GP10 Ultra Lite LED Projector User Manual

GP10 Ultra Lite LED Projector User Manual
GP10
Ultra Lite LED Projector
User Manual
http://www.pureglare.com.au
Table of contents
Important safety
instructions ................... 3
Introduction.................. 6
Projector features.....................................6
Shipping contents ......................................7
Projector exterior view...........................8
Controls and functions ............................9
Positioning your
projector ..................... 14
Obtaining a preferred projected image
size..............................................................14
Connection ................. 16
Connecting the power...........................16
Connecting the DVD player.................16
Connecting a computer.........................17
Connecting Video source devices.......19
Connecting an HDMI source device ..20
Connecting a Component Video source
device.........................................................21
Connecting a composite Video source
device.........................................................22
Connecting an external speaker..........23
Connecting to an external memory
device.........................................................24
Playing sound through the projector..25
Selecting the aspect ratio...................... 31
Optimizing the image............................. 32
Operating in a high
altitude environment ............................. 34
Adjusting the sound ............................... 34
Displaying images with PC and Video
source devices......................................... 36
Using PC/ Video pop-up menus .......... 37
Displaying files with internal memory,
USB Drive and SD card......................... 39
Using USB streaming ............................. 51
Using wireless streaming ...................... 53
Using settings menu ............................... 60
Shutting down the projector ............... 65
Maintenance ............... 66
Care of the projector............................ 66
Troubleshooting......... 68
Specifications.............. 69
Projector specifications......................... 69
Dimensions .............................................. 70
Timing chart............................................. 71
Warranty and Copyright
information................. 74
Operation ................... 26
Starting up the projector ......................26
Switching input signal .............................26
Adjusting the projected image .............27
Hiding the image......................................28
Securing the projector...........................29
Firmware upgrade...................................31
2
Table of contents
http://www.pureglare.com.au
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that
you follow the instructions mentioned in this manual and marked on the product.
Safety Instructions
1.
Please read this manual before
you operate your projector. Save
it for future reference.
2.
Do not look straight at the
projector lens during operation.
The intense light beam may damage
your eyes.
3.
4.
In some countries, the line voltage is
NOT stable. This projector is
designed to operate safely within a
mains voltage of 19 volts DC, but
could fail if power cuts or surges of
10 volts occur. In areas where the
mains voltage may fluctuate or
cut out, it is recommended that
you connect your projector
through a power stabilizer, surge
protector or uninterruptible
power supply (UPS).
5.
Do not block the projection lens with
any objects when the projector is
under operation as this could cause
the objects to become heated and
deformed or even cause a fire.
Refer servicing to qualified
service personnel.
Important safety instructions
http://www.pureglare.com.au
3
Safety Instructions (Continued)
6.
Never replace any electronic
components unless the projector is
unplugged.
9.
10.
4
7.
Do not place this product on an
unstable cart, stand, or table. The
product may fall, sustaining serious
damage.
8.
Do not attempt to disassemble this
projector. There are dangerous high
voltages inside which may cause
death if you should come into
contact with live parts. Refer
servicing only to suitably qualified
professional service personnel.
When the projector is under
operation, you may sense some
heated air and odor from its
ventilation grill. It is a normal
phenomenon and not a product
defect.
Do not place this projector in any
of the following environments.
- Space that is poorly ventilated or
confined. Allow at least 50 cm
clearance from walls and free flow of
air around the projector.
- Locations where temperatures may
become excessively high, such as the
inside of a car with all windows rolled
up.
- Locations where excessive humidity,
dust, or cigarette smoke may
contaminate optical components,
shortening the projector's life span
and darkening the image.
Important safety instructions
http://www.pureglare.com.au
Safety Instructions (Continued)
- Locations near fire alarms
13.
- Locations with an ambient temperature
above 40°C / 104°F
- Locations where the altitudes are higher
than 3000 m (10000 feet).
Do not stand the projector on end
vertically. Doing so may cause the
projector to fall over, causing injury or
resulting in damage to the projector.
3000 m
(10000 feet)
0m
(0 feet)
11.
14.
Do not step on the projector or place
any objects upon it. Besides probable
physical damage to the projector,
doing so may result in accidents and
possible injury.
15.
If the ventilation holes are seriously
obstructed, overheating inside the
projector may result in a fire.
Always place the projector on a level,
horizontal surface during operation.
Do not place liquids near or on the
projector. Liquids spilled into the
projector may cause it to fail. If the
projector does become wet,
disconnect it from the power supply's
wall socket and call BenQ to have the
projector serviced.
Do not block the ventilation holes.
- Do not place this projector on a blanket,
bedding or any other soft surface.
- Do not cover this projector with a cloth
or any other item.
- Do not place inflammables near the
projector.
12.
Important safety instructions
http://www.pureglare.com.au
5
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features.
•
•
•
•
•
•
•
6
Advanced LED light source
Long lasting LEDs provides a longer life span than traditional lamps.
Optical engine with DLP technologies
WXGA resolution and a bright picture.
Various useful features
Supports iPhone/iPod player, multimedia player, document viewer, internal memory, SD
card, USB flash drive, and USB display
Easy to carry
The projector is small and light, making it useful for business trips and leisure activities.
You can view documents, videos and photos anywhere.
Multiple input ports
Multiple input ports, including PC, AV, HDMI, USB, and SD card provide flexible
connectivity with peripheral devices.
Audio input & output
Equipped with 3W x 2 speakers with RCA & mini-jack input ports and phone jack
output port
Convenient menu items
Friendly menu is used for all types of inputs, making the projector easy to use.
•
The apparent brightness of the projected image will vary depending on the ambient lighting
conditions, selected input signal contrast/brightness settings, and is proportional to
projection distance.
•
The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
Introduction
http://www.pureglare.com.au
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these items
are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those illustrated.
*The warranty card is only supplied in some specific regions. Please consult your dealer for
detailed information.
Projector
Power cord
VGA cable
Warranty card*
Projector carrying bag
Joybee GP2
Mini Projector
User Manual
Quick start guide
Pull the tab before using
the remote control.
Remote control with
battery
Wi-Fi dongle
User manual is inside the Projector device internal memory. Please use USB cable to link PC/
Notebook and Projector device. In main UI page, choose "USB streaming" > "USB File
transfer". Meanwhile, projector device will be treated as external storage and you can access
UM via PC/Notebook.
Optional accessories
DVD Player
Introduction
http://www.pureglare.com.au
7
Projector exterior view
Front/upper side
1
2
7
3
3
1
4
8
2
5
8.
9.
10.
11.
12.
13.
14.
6
Rear/lower side
10 11 12 13 14 15 16 17
9
1.
2.
3.
4.
5.
6.
7.
18
19
15.
16.
17.
18.
19.
20.
Vent (cold air intake)
Internal Speakers
Vent (heated air exhaust)
Front IR remote sensor
Projection lens
Lens cover
External control panel
(See "Projector" on page 9 for
details.)
Focus ring
AC power jack
SD card slot
Type A USB jack
Mini-B USB jack
HDMI input jack
RGB (PC)/Component Video
(YPbPr/ YCbCr) signal input jack
Video input jack
Audio input jack
Audio output jack
Kensington anti-theft lock slot
Adjuster feet
Tripod socket
20
19
Do not block the ventilation openings. Blocking the ventilation openings can cause your
projector to overheat and may cause it to fail.
8
Introduction
http://www.pureglare.com.au
Controls and functions
Projector
4.
8
1
9
10
2
3
4
5
6
11
12
7
5.
1.
POWER indicator light
Lights up or flashes when the projector is
under operation.
2.
Power
Toggles the projector between standby
mode and on.
See "Starting up the projector" on page 26
and "Shutting down the projector" on page
65 for details.
6.
Up/Volume up key
When the On-Screen Display (OSD)
7.
menu is on:
- Navigate up to select the desired menu
items.
- Make adjustments. (e.g. manual
keystone...)
When the On-Screen Display (OSD) menu
is off: (Only applied to SD card, internal
memory and USB Drive)
- Magnifies the volume level.
3.
I
I
Left key
When the On-Screen Display (OSD)
menu is on:
- Navigate left to select the desired menu
items.
- Make adjustments. (e.g. brightness,
contrast...)
When the On-Screen Display (OSD)
menu is off: (Only applied to SD card,
internal memory and USB Drive)
- Play previous video and audio file.
- Press and hold to rewind video and
audio file.
OK/Blank
Short press:
- Confirms a selected function when a
menu is displayed.
- Plays or pauses a video, music, photo
slideshow. (Only applied to SD card,
internal memory and USB Drive)
Long press (3 seconds):
Toggles the Blank.
Menu
Turns on the Pop-up setting menu.
Down/Volume down key
When the On-Screen Display (OSD)
menu is on:
- Navigate to down to select the desired
menu items.
- Make adjustments. (e.g. manual
keystone...)
When the On-Screen Display (OSD)
menu is off: (Only applied to SD card,
internal memory and USB Drive)
- Reduces the volume level.
Introduction
http://www.pureglare.com.au
9
8.
TEMPerature indicator light
Lights up red if the projector's
temperature becomes too high.
9.
LED indicator light
Indicates the status of the light source.
Lights up or flashes when the light source
has developed a problem.
10. Home
Directly returns to home screen from
lower level of OSD.
Exits application/pop-up message and back
to home screen directly.
11. Right key
When the On-Screen Display (OSD) menu
is on:
- Navigate right to select the desired menu
items.
- Make adjustments. (e.g. brightness,
contrast...)
When the On-Screen Display (OSD) menu
is off: (Only applied to SD card, internal
memory and USB Drive)
- Play next video and audio file.
- Press and hold to fast forward video and
audio file.
12. Back
Goes back to previous OSD menu, exits
and saves menu settings.
10
Introduction
http://www.pureglare.com.au
Remote control
4.
1
8
2
9
3
4
5
6
7
10
11
12
5.
1.
2.
3.
POWER
Toggles the projector between standby
mode and on. See "Starting up the
projector" on page 26 and "Shutting down
the projector" on page 65 for details.
Blank
Toggles Blank on and off. See "Hiding the
6.
image" on page 28 for details.
Up/Volume up key
When the On-Screen Display (OSD)
menu is on:
- Navigate up to select the desired menu 7.
items.
- Make adjustments. (e.g. manual
keystone...)
When the On-Screen Display (OSD)
8.
menu is off: (Only applied to SD card,
internal memory and USB Drive)
- Magnifies the volume level.
9.
I
I
Left key
When the On-Screen Display (OSD)
menu is on:
- Navigate left to select the desired menu
items.
- Make adjustments. (e.g. brightness,
contrast...)
When the On-Screen Display (OSD)
menu is off: (Only applied to SD card,
internal memory and USB Drive)
- Play previous video and audio file.
- Press and hold to rewind video and
audio file.
Down/Volume down key
When the On-Screen Display (OSD)
menu is on:
- Navigate to down to select the desired
menu items.
- Make adjustments. (e.g. manual
keystone...)
When the On-Screen Display (OSD)
menu is off: (Only applied to SD card,
internal memory and USB Drive)
- Reduces the volume level.
Back
Returns to upper level of OSD.
Closes pop-up setting menu of OSD.
Leave current application of OSD.
Home
Directly returns to home screen from
lower level of OSD.
Exits application/pop-up message and
back to home screen directly.
Mute
Toggles projector audio between on and
off.
Auto
Automatically determines the best
picture timings for the displayed
computer image. See "Auto-adjusting the
image" on page 27 for details.
Introduction
http://www.pureglare.com.au
11
10. Right key
When the On-Screen Display (OSD) menu
is on:
- Navigate right to select the desired menu
items.
- Make adjustments. (e.g. brightness,
contrast...)
When the On-Screen Display (OSD) menu
is off: (Only applied to SD card, internal
memory and USB Drive)
- Play next video and audio file.
- Press and hold to fast forward video and
audio file.
11. OK
Confirms a selected function when a menu
is displayed.
Plays or pauses a video, music, photo
slideshow. (Only applied to SD card,
internal memory and USB Drive)
12. Menu
Turns on the Pop-up setting menu.
12
Introduction
http://www.pureglare.com.au
Remote control effective range
Infra-Red (IR) remote control sensor is located on
the front of the projector. The remote control must
be held at an angle within 15 degrees perpendicular
to the projector's IR remote control sensor to
function correctly. The distance between the remote
control and the sensor should not exceed 7 meters
(~ 23 feet).
Appr
ox. 1
5°
Make sure that there are no obstacles between the
remote control and the IR sensor on the projector
that might obstruct the infra-red beam.
Replacing the remote control battery
1.
Pull out the battery holder.
Please follow the illustrated instructions. Push and hold
the locking arm while pulling out the battery holder.
2.
3.
Insert the new battery in the holder. Note the
positive polarity should face outward.
Push the holder into the remote control.
•
Avoid excessive heat and humidity.
•
There may be battery damage if the battery is
incorrectly replaced.
•
Replace only with the same or equivalent type recommended by the battery manufacturer.
•
Dispose of the used battery according to the battery manufacturer’s instructions.
•
Never throw a battery into a fire. There may be danger of an explosion.
•
If the battery is dead or if you will not be using the remote control for a long time, remove
the battery to prevent damage to the remote control from possible battery leakage.
Introduction
http://www.pureglare.com.au
13
Positioning your projector
Obtaining a preferred projected image size
The distance from the projector lens to the screen, the zoom setting (if available), and the
video format each factors in the projected image size.
16:10 is the native aspect ratio of this projector.
16:10 aspect image scaled to a 4:3 aspect
display area
The projector should always be placed horizontally level (like flat on a table), and
positioned directly perpendicular (90° right-angle square) to the horizontal center of the
screen. This prevents image distortion caused by angled projections (or projecting onto
angled surfaces).
The modern digital projector does not project directly forward (like older style reel-toreel film projectors did). Instead, digital projectors are designed to project at a slightly
upward angle above the horizontal plane of the projector. This is so that they can be
readily placed on a table and will project forward and upwards onto a screen positioned so
that the bottom edge of the screen is above the level of the table (and everyone in the
room can see the screen).
If the projector is mounted on a ceiling, it must be mounted upside-down so that it
projects at a slightly downward angle.
You can see from the diagram on page 15, that this type of projection causes the bottom
edge of the projected image to be vertically offset from the horizontal plane of the
projector. When ceiling mounted, this refers to the top edge of the projected image.
If the projector is positioned further away from the screen, the projected image size
increases, and the vertical offset also increases proportionately.
When determining the position of the screen and projector, you will need to account for
both the projected image size and the vertical offset dimension, which are proportional to
the projection distance.
BenQ has provided a table of screen size to assist you in determining the ideal location for
your projector. Refer to "Projection dimensions" on page 15 depending on the projector
you are using. There are two dimensions to consider, the perpendicular horizontal distance
from the center of the screen (projection distance), and the vertical offset height of the
projector from the horizontal edge of the screen (offset).
14
Positioning your projector
http://www.pureglare.com.au
Projection dimensions
Refer to "Dimensions" on page 70 for the center of lens dimensions of this projector
before calculating the appropriate position.
1280:800 screen diagonal
Screen
Center of lens
Projection distance
Screen Size
Diagonal
W (mm)
Inches
mm
30
40
50
60
80
100
120
150
200
220
250
300
762
1016
1270
1524
2032
2540
3048
3810
5080
5588
6350
7620
646
862
1077
1292
1723
2154
2585
3231
4308
4739
5385
6462
H (mm)
404
538
673
808
1077
1346
1615
2019
2692
2962
3365
4039
Projection distance in mm
750
1000
1250
1500
2000
2500
3000
3750
5000
5500
6250
7500
All measurements are approximate and may vary from the actual sizes. BenQ recommends that
if you intend to permanently install the projector, you should physically test the projection size
and distance using the actual projector in situ before you permanently install it, so as to make
allowance for this projector's optical characteristics. This will help you determine the exact
mounting position so that it best suits your installation location.
Positioning your projector
http://www.pureglare.com.au
15
Connection
In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 7). They are commercially available from electronics stores.
Connecting the power
1.
2.
Insert one end of the provided power cord into the AC IN terminal.
Insert the plug on the power cord into a wall outlet. Check that the Power LED
indicator on the projector lights orange when using the AC adapter.
Connecting the DVD player
1.
2.
3.
4.
5.
16
Take the DVD player (optional) and connect it to the projector as illustrated below.
Connect the projector power and insert the disc.
Turn on the projector and press
/ to select DVD and press OK to connect.
Use the remote control for the DVD player to operate the DVD player.
To disconnect the DVD player, remove the disc. And press the button on the front of
the DVD player while removing the DVD player from the projector.
•
The projector automatically starts the disc when it is inserted.
•
The DVD player supports hot-plugging function. You can connect or disconnect the DVD
player while the projector is turned on.
Connection
http://www.pureglare.com.au
Connecting a computer
The projector provides a VGA input socket that allows you to connect it to both IBM®
compatibles and Macintosh® computers. A Mac adapter is needed if you are connecting
legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
• Using a VGA cable
1.
Take the supplied VGA cable and connect one end to the D-Sub output socket of the
computer.
2.
Connect the other end of the VGA cable to the COMPUTER socket on the
projector.
3.
If you wish to make use of the projector speaker, take a suitable audio cable and
connect one end of the cable to the audio output socket of the computer, and the
other end to the audio input socket on the projector.
Notebook or desktop computer
Audio
cable
VGA cable
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press
FN and the labeled function key simultaneously. Refer to your notebook's documentation to find
your notebook's key combination.
Connection
http://www.pureglare.com.au
17
• Using an HDMI cable
1.
Take an HDMI cable and connect one end to the HDMI output jack of the computer.
2.
Connect the other end of the HDMI cable to the HDMI jack on the projector.
• Using a USB cable
1.
Take a USB cable and connect the type A end to the USB output jack of the
computer.
2.
Connect the mini-B type end of the USB cable to the mini-B USB jack on the
projector. When you connect the projector to a computer, you can display
computer’s image or transfer files from your computer to the internal memory of the
projector.
3.
4.
18
If you select USB Display, follow the on-screen message to install the USB driver in
your computer first.
If you select USB File Transfer, go to My Computer or Windows Explorer to access
the projector's files. The projector appears as a Removable Disk. Transfer the files
from your computer to the projector by dragging and dropping or copying and
pasting.
To disconnect the projector from a computer:
i. Click
on the Windows Taskbar.
ii. Click the pop-up message.
Connection
http://www.pureglare.com.au
iii. Disconnect the USB cable only when the message says that it is safe to remove
the hardware.
•
Do not disconnect the USB cable while the files are being copied, as this could result in loss
of data or damage to the projector.
•
The connection will not end if you have projector files open on the computer. Close all
projector files and try again.
•
Other versions of Windows operate similarly. Follow the correct procedure for removing a
USB device from your computer safely for your version of Windows.
Connecting Video source devices
You need only connect the projector to a Video source device using just one of the above
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the Video source device as described below:
Terminal name
Terminal appearance
Picture quality
HDMI
HDMI
Best
Component Video
VGA
Better
Video
Video
Good
If the selected video image is not displayed after the projector is turned on and the correct video
source has been selected, check that the Video source device is turned on and operating
correctly. Also check that the signal cables have been connected correctly.
Connection
http://www.pureglare.com.au
19
Connecting an HDMI source device
The projector provides a HDMI input jack that allows you to connect it to an HDMI
source device like a Blu-Ray player, a DTV tuner or a display.
HDMI (High-Definition Multimedia Interface) supports uncompressed video data
transmission between compatible devices like DTV tuners, Blu-Ray player and displays over
a single cable. It provides pure digital viewing and listening experience.
Examine your Video source device to determine if it has a set of unused HDMI output
jacks available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an HDMI source device:
1.
2.
20
Take an HDMI cable and connect one end to the HDMI output jack of the HDMI
source device.
Connect the other end of the HDMI cable to the HDMI jack on the projector.
•
The HDMI cable (shown in this example) for connection your video output device is not
supplied as standard.
•
The Apple Digital AV Adapter can be purchased from www.apple.com.
Connection
http://www.pureglare.com.au
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video
output sockets available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1.
2.
3.
Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3
RCA type connectors to the Component Video output sockets of the Video source
device. Match the color of the plugs to the color of the sockets; green to green, blue
to blue, and red to red.
Connect the other end to the COMPUTER socket on the projector.
If you wish to make use of the projector speaker, take a suitable audio cable and
connect one end of the cable to the audio output sockets of the Video source
device, and the other end to the audio input socket on the projector.
AV device
Audio cable
Component Video to VGA
(D-Sub) adaptor cable
•
When audio output jack is connected with the earphone or external speaker, the sound will
not come out from the projector speaker.
•
No sound will come out from the speaker or audio output jack if video signals are not input.
Besides, the sound cannot be adjusted either.
Connection
http://www.pureglare.com.au
21
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video
output sockets available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1.
2.
3.
Take a Video cable and connect one end to the composite Video output socket of
the Video source device.
Connect the other end of the Video cable to the Video jack on the projector.
If you wish to make use of the projector speaker, take a suitable audio cable and
connect one end of the cable to the audio output sockets of the Video source
device, and the other end to the audio input socket on the projector.
AV device
Audio cable
Video cable
You need only connect to this device using a composite Video connection if Component Video
input is unavailable for use. See "Connecting Video source devices" on page 19 for details.
22
Connection
http://www.pureglare.com.au
Connecting an external speaker
You can hear sound through an external speaker instead of the internal speakers built into
the projector.
To connect the projector to an external speaker source device:
1.
Connect an appropriate stereo cable to the external speaker and the audio output
jack on the projector.
When the audio cable is connected to the audio output jack, the speaker output is muted.
Connection
http://www.pureglare.com.au
23
Connecting to an external memory device
Connecting an SD card
To connect the projector to an SD card:
1.
Connect an SD card to the SD card slot on the projector.
•
The maximum memory capacity supported for an SD(HC) card is 32 GB. (The maximum
capacity supported for external memory is based on our factory test. Your experience may
differ depending on the manufacturer of the memory device.)
•
The projector may not be compatible with some SD cards.
Connecting a USB storage device
To connect the projector to a USB storage device:
1.
Plug the USB storage device into the Type A USB socket.
USB flash drive
24
•
This product supports USB memory device and HDD (Hard Disk Drive). Only one and only
last one of partitions will be mounted. (The maximum capacity supported for external
memory is based on our factory test. Your experience may differ depending on the
manufacturer of the memory device.)
•
This product does not support multi-card readers.
•
This product does not work if the USB storage device is connected by a USB HUB.
•
Some products which do not comply with standard USB specifications might not operate
normally.
•
A USB storage device with an automatic recognition application or its own driver might not
operate normally.
Connection
http://www.pureglare.com.au
•
A USB storage device that uses only a designated driver might not be recognized.
•
Recognition speed for USB storage device may vary by device.
•
Do not turn off the product or pull a connected USB storage device out while the USB
storage device is in use. Doing so may result in damage to the USB storage device or stored
file.
•
Use a USB storage device which contains normal files. Abnormal files can cause a
malfunction or the files may not play.
•
USB storages must be formatted in FAT16/FAT32/NTFS. FAT32 and NTFS are
recommended for HDD (Hard Disk Drive).
•
As the data in the USB storage device can be damaged, please back up important data to
avoid loss. The user is responsible for data management. BenQ shall not be held liable for
any data loss.
•
File tree in USB storage should be as simple as possible. Too many or too many layers of
folders will result in lag of access time.
•
If an external memory device does not operate after you’ve connected it to the projector,
try to connect it to a PC. If it still does not operate normally, contact the memory device’s
manufacturer service center or related customer center.
Playing sound through the projector
You can make use of the projector speaker in your presentations, and also connect
separate amplified speakers to the audio output jack of the projector.
The table below describes the connection methods for different devices, and where the
sound is from.
Device
PC/Component video
Audio input (L/R)
Audio input jack
The projector can play the
sound from...
AUDIO-IN
Audio input (L/R)
AUDIO-IN
Video
Audio input (L/R)
Audio input (L/R)
Audio output jack
•
The selected input signal determines which sound will be played by the projector speaker,
and which sound will be output from the projector when audio output jack is connected.
•
There’s no need to connect to an audio input jack because the projector can play the sound
from an HDMI, external memory and iPhone/iPod source device. However, you can connect
to an external device to play the sound.
•
USB display doesn’t support audio function.
Connection
http://www.pureglare.com.au
25
Operation
Starting up the projector
1.
Connect the power using the power cord. The Power indicator turns into orange.
2.
Press II Power on the projector or remote
control to start the projector. The Power
indicator lights green when the projector is
on.
The start up procedure takes several seconds.
In the later stage of start up, a startup logo is
projected.
(If necessary) Rotate the focus ring to adjust
the image clearness.
If the projector is activated for the first time, select your OSD language following the
onscreen instructions.
If you are prompted for a password, press the
arrow keys to enter a six digit password. See
"Utilizing the password function" on page 29
for details.
Switch all of the connected equipment on.
The projector will display the home screen.
3.
4.
5.
6.
If the frequency/resolution of the input signal exceeds
the projector's operating range, you will see the
message 'Out of Range' displayed on a blank screen.
Please change to an input signal which is compatible with the projector's resolution or set the
input signal to a lower setting. See "Timing chart" on page 71 for details.
Switching input signal
The projector can be connected to multiple devices
at the same time. However, it can only display one
full screen at a time. Press
/ on the projector
or remote control to select your desired input
signal.
26
•
The input signal type effects the options available
for the Picture Mode. See "Selecting a picture
mode" on page 32 for details.
•
The native display resolution of this projector is in a
16:10 aspect ratio. For best display picture results, you should select and use an input signal
which outputs at this resolution. Any other resolutions will be scaled by the projector
depending upon the 'aspect ratio' setting, which may cause some image distortion or loss of
picture clarity. See "Selecting the aspect ratio" on page 31 for details.
Operation
http://www.pureglare.com.au
Adjusting the projected image
Adjusting the image height
The projector is equipped with 2 adjuster feet. This adjusters change the image height. To
adjust the projector:
1.
Screw the adjuster feet to adjust the image
height.
To retract the feet, screw the adjuster feet in a
reverse direction.
If the projector is not placed on a flat surface or
the screen and the projector are not
perpendicular to each other, the projected image
becomes trapezoidal. To correct this situation, see
"Correcting keystone" on page 28 for details.
•
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyes.
•
Be careful when you screw the adjuster foot as it is close to the exhaust vent where hot air
comes from.
Fine-tuning the image clarity
1.
Rotate the focus ring to sharpen the image.
Auto-adjusting the image
In some cases, you may need to optimize the picture quality.
• Using the remote control
Press AUTO.
Within 3 seconds, the built-in Intelligent Auto
Adjustment function will re-adjust the values of
Frequency and Clock to provide the best picture
quality.
The current source information will be displayed
in the upper left corner of the screen for 3
seconds.
This function is only available when PC signal (analog RGB) is selected.
Operation
http://www.pureglare.com.au
27
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either
the top or bottom. It occurs when the projector is not perpendicular to the screen.
Correcting keystone when an image is displayed on the screen.
To correct this, besides adjusting the height of the projector, you will need to manually
correct it following one of these steps.
1.
2.
Press
and then press
to highlight
Keystone. The Keystone pop-up menu
displays.
Press
to correct keystoning at the
bottom of the image or press
to correct
keystoning at the top of the image.
Press
.
Hiding the image
In order to draw the audience's full attention to the presenter, you can:
• Using the remote control
Use Blank on the remote control to hide the screen
image. Press again Blank or any keys on the remote
control to restore the image.
• Using the projector
Press and hold Blank for 3 seconds on the projector
to hide the screen image. Press again Blank or any
keys on the projector to restore the image.
Do not block the projection lens from projecting as this
could cause the blocking object to become heated and
deformed or even cause a fire.
28
Operation
http://www.pureglare.com.au
Press
.
Securing the projector
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an
option for setting up password security. The password can be set through the Settings
menu.
You will be inconvenienced if you activate the power-on lock functionality and subsequently
forget the password. Print out this manual (if necessary) and write the password you used in this
manual, and keep the manual in a safe place for later recall.
Setting power on lock
•
Once a password has been set, the projector cannot be used unless the correct password is
entered every time the projector is started.
•
When setting a password for the projector that its password function is used for the first
time, enter the default password (1, 1, 1, 1, 1, 1) of the projector by pressing the arrow key
five times if you are prompted for a password.
1.
2.
3.
4.
5.
6.
7.
Press
/
until the Settings menu is highlighted and then press OK to enter.
Go to the Advanced > Security Settings > Change Security Settings menu.
Press OK. The message 'Input Current Password' displays.
As pictured to the right, the four arrow keys
( ,
, , ) respectively represent 4 digits
(1, 2, 3, 4). Press the arrow keys to enter six
digits for the password.
Once the correct password is set, the OSD
menu returns to the Change Security
Settings menu.
Highlight Power on Lock and press OK. The
pop-up menu displays. Select On and press OK to complete power on lock setting.
To leave the OSD menu, press
or .
If you forget the password
If the password function is activated, you will be asked
to enter the six-digit password every time you turn on
the projector. If you enter the wrong password, the
password error message displays lasting for three
seconds, and the message 'Input Password' follows.
If you enter an incorrect password 5 times in
succession, the projector will automatically shut down
in a short time.
Operation
http://www.pureglare.com.au
29
Entering the password recall procedure
1.
2.
3.
Press and hold
on the remote control for 3
seconds. The projector will display a coded
number on the screen.
Write down the number and turn off your
projector.
Seek help from the local BenQ service center to
decode the number. You may be required to
provide proof of purchase documentation to
verify that you are an authorized user of the projector.
Changing the password
1.
2.
3.
4.
Go to the Settings > Advanced > Security Settings > Change password
menu.
Press OK. The message 'Input Current Password' displays.
Enter the old password.
•
If the password is correct, another message 'Input New Password' displays.
•
If the password is incorrect, the password error message displays lasting for three
seconds, and the message 'Input Current Password' displays for your retry.
You can press
to cancel the change or try another password.
Enter a new password.
The digits being input will display as asterisks on-screen. Write your selected password down
here in this manual in advance or right after the password is entered so that it is available to you
should you ever forget it.
Password: __ __ __ __ __ __
Keep this manual in a safe place.
5.
6.
7.
Confirm the new password by re-entering the
new password.
You have successfully assigned a new password
to the projector. Remember to enter the new
password next time the projector is started.
To leave the OSD menu, press
or .
Disabling the password function
To disable password protection, go back to the Settings > Advanced > Security
Settings > Power on Lock menu. Select Off and press OK. The message'Input
Password'displays. Enter the current password.
30
•
If the password is correct, the OSD menu returns to the Security Settings
page with 'Off' shown in the row of Power on Lock. You will not have to enter
the password next time you turn on the projector.
•
If the password is incorrect, the password error message displays lasting for three
seconds, and the message'Input Password'displays for your retry. You can press
to cancel the change or try another password.
Operation
http://www.pureglare.com.au
Though the password function is disabled, you need to keep the old password in hand should you
ever need to re-activate the password function by entering the old password.
Firmware upgrade
Follow below procedures to upgrade firmware version.
•
Only an SD Card is supported for a firmware update.
•
Do not remove the SD Card while an update is in progress.
•
Do not operate any buttons during the update.
•
Do not turn the projector off during the update.
•
To confirm that the firmware has been successfully updated, go to Settings > Information
> Firmware version.
Updating the Firmware
1.
2.
3.
4.
5.
Connect the SD card containing the latest firmware to the projector.
Select Settings > Advanced > Firmware Upgrade in the main menu page.
Select OK to begin.
After the firmware is updated, please turn off the projector.
Power on the projector and check the firmware version.
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and
computers are in 4:3 ratio, which is the default for this projector, and digital TV and DVDs
are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can
dynamically stretch and scale the image output to a different aspect than that of the image
input signal.
To change the projected image ratio (no matter what aspect the source is):
1.
2.
3.
Press
to open the pop-up menu in one of the computer, DVD player, composite
video, component and HDMI modes.
Press
to highlight Aspect Ratio.
Press
/
to select an aspect ratio to suit the format of the video signal and your
display requirements.
Operation
http://www.pureglare.com.au
31
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined picture
modes so that you can choose one to suit your
operating environment and input signal picture type.
To select an operation mode that suits your need, you
can follow one of the following steps.
•
•
•
Make sure the input source is on computer, DVD
player, composite video, component and HDMI
mode and the projection screen is displayed.
Press Mode on the remote control projector repeatedly until your desired mode is
selected.
You may press
to open the pop-up menu. Press
to select Picture Mode
Settings and press OK to enter. Select Picture Mode and press
/
to select a
desired mode.
The picture modes are listed below.
1.
2.
3.
4.
5.
Bright mode: Maximizes the brightness of the projected image. This mode is
suitable for environments where extra-high brightness is required, such as using the
projector in well lit rooms.
Standard mode (Default): Is designed for presentations. The brightness is
emphasized in this mode.
Cinema mode: Is appropriate for playing colorful movies, video clips from digital
cameras or DVs through the PC input for best viewing in a blackened (little light)
environment.
Game mode: Is appropriate for playing games.
User mode: Recalls the settings customized based on the current available picture
modes. See "Setting the User mode" on page 32 for details.
Setting the User mode
There is one user-definable modes if the current available picture modes are not suitable
for your need. You can use one of the picture modes (except the User) as a starting point
and customize the settings.
1.
2.
3.
4.
Press
to open the pop-up menu.
Press
to select Picture Mode Settings and press OK to enter.
Select Picture Mode and press
/
to select User.
Press
to highlight Reference Mode.
This function is only available when User mode is selected in the Picture Mode sub-menu item.
5.
6.
7.
8.
32
Press
/
to select a picture mode that is closest to your need.
Press
to select a sub-menu item to be changed and adjust the value with
/ .
See "Fine-tuning the image clarity" below for details.
When all settings have been done, highlight Save Settings and press OK to store
the settings.
The confirmation message 'Setting Saved' displays.
Operation
http://www.pureglare.com.au
Using Wall Color
In the situation where you are projecting onto a colored surface such as a painted wall
which may not be white, the Wall Color feature can help correct the projected picture’s
color to prevent possible color difference between the source and projected pictures.
To use this function, press
to open the pop-up menu in one of the computer, iPhone/
iPod, composite video, component and HDMI modes. Select Wall Color and press
/
to select a color which is the closest to the color of the projection surface. There are
several precalibrated colors to choose from: Light Yellow, Pink, Light Green, Blue, and
Blackboard.
Fine-tuning the image quality in user mode
According to the detected signal type, there are some user-definable functions available
when User mode is selected. Based on your needs, you can make adjustments tothese
functions by highlighting them and pressing
/
on the projector or remote control
Adjusting Brightness
The higher the value, the brighter the image. And the
lower the setting, the darker the image. Adjust this
control so the black areas of the image appear just as
black and that detail in the dark areas is visible.
+30
+50
+70
+30
0
-30
Adjusting Contrast
The higher the value, the greater the contrast. Use this
to set the peak white level after you have previously
adjusted the Brightness setting to suit your selected
input and viewing environment.
Adjusting Color
Lower setting produces less saturated colors. If the setting is too high, colors on the image
will be overpowering, which makes the image unrealistic.
Adjusting Tint
The higher the value, the more reddish the picture becomes. The lower the value, the
more greenish the picture becomes.
Adjusting Sharpness
The higher the value, the sharper the picture becomes. The lower the value, the softer the
picture becomes.
Selecting a Color Temperature
There are a number of options available for color temperature* settings vary according to
the signal type selected.
*About color temperatures:
There are many different shades that are considered to be "white" for various purposes.
One of the common methods of representing white color is known as the “color
temperature”. A white color with a low color temperature appears to be reddish white. A
white color with a high color temperature appears to have more blue in it.
Operation
http://www.pureglare.com.au
33
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between
1500 m –3000 m above sea level, and ambient temperature is between 0°C–30°C.
Do not use the High Altitude Mode if your altitude is between 0 m and 1499 m and ambient
temperature is between 0°C and 35°C. The projector will be over cooled, if you turn the mode
on under such a condition.
To activate the High Altitude Mode:
1.
2.
3.
4.
Hightlight Settings and press OK to enter.
Go to Advanced > High Altitude Mode and press OK.
Highlight On and press OK to confirm.
To leave the OSD, press
until the projector returns to the home screen, or press
to go back to the home screen directly.
Operation under "High Altitude Mode" may cause a higher decibel operating noise level
because of increased fan speed necessary to improve overall system cooling and
performance.
If you use this projector under other extreme conditions excluding the above, it may
display auto shut-down symptoms, which is designed to protect your projector from overheating. In cases like this, you should switch to High Altitude mode to solve these
symptoms. However, this is not to state that this projector can operate under any and all
harsh or extreme conditions.
Adjusting the sound
The sound adjustments made as below will have an effect on the projector speaker(s). Be
sure you have made a correct connection to the projector audio input. See "Connection"
on page 16 for how the audio input is connected.
SRS HD
Activating this function enables the SRS HD technology. The projector can provide a
surround sound and restore natural sound.
1.
2.
3.
4.
5.
Hightlight Settings and press OK to enter.
Go to Advanced > Audio Settings and press
OK to enter.
Highlight SRS HD and press OK to open the popup menu.
Highlight On and press OK to confirm.
To leave the OSD, press
until the projector
returns to the home screen, or press
to go back to the home screen directly.
Muting the sound
To temporarily turn off the sound, press
control, or:
34
on the remote
Operation
http://www.pureglare.com.au
1.
2.
3.
4.
5.
Hightlight Settings and press OK to enter.
Go to Advanced > Audio Settings and press
OK to enter.
Highlight Mute and press OK to open the pop-up
menu.
Highlight On and press OK to confirm.
To leave the OSD, press
until the projector
returns to the home screen, or press
to go back to the home screen directly.
Adjusting the sound level
To adjust the sound level, press + or - on the remote control.
Turning off Power on/off ring tone
To turn off the Power on/off ring tone:
1.
2.
3.
Repeat steps 1-2 above.
Highlight Power on/off ring tone and press OK
to open the pop-up menu.
Highlight Off and press OK to confirm.
The only way to change Power On/Off Ring Tone is setting
On or Off here. Setting the sound mute or changing the sound level will not affect the Power
On/Off Ring Tone.
Operation
http://www.pureglare.com.au
35
Displaying images with PC and Video source
devices
You can connect your projector to a PC and various Video source devices. (e.g. HDMI,
composite video, component video) However, you need only connect the projector to an
input source device.
To display images:
1.
2.
3.
4.
36
Connect the projector to one of the above signal source.
Turn on the power of the projector and your source device. The projector displays
the home screen.
Press
/
on the projector or remote control to select the input signal and then
press OK to enter.
Press
or
to go back to home screen.
Operation
http://www.pureglare.com.au
Using PC/ Video pop-up menus
The projector has a multilingual OSD that allows you to make image adjustments and
change a variety of settings. This menu is for the settings to be used in computer, DVD
player, composite video, component and HDMI modes.
Using the menu
1.
2.
3.
To open the OSD menu, press
on the projector or remote control when the
projection screen is displayed.
When the OSD is displayed, press / to select the desired item and adjust the
settings by using
/ .
To leave the OSD, press
again.
Menu system
Menu Item
Sub-menu
Options
Wall Color
Off/Light Yellow/Pink/Light Green/
Blue/Blackboard
Aspect Ratio
Auto/Real/4:3/16:9/16:10
Auto Keystone
On/Off
Keystone
Picture Mode
Bright/Standard/Cinema/Game/User
Reference Mode
Bright/Standard/Cinema/Game/User
Brightness
Picture Mode
Settings
Contrast
Color
Tint
Sharpness
Color Temperature
Normal/Cold/Warm
Save Settings
3D Sync Invert
Disable/Invert
Source
Information
Resolution
Color System
Operation
http://www.pureglare.com.au
37
Description of each menu
FUNCTION
DESCRIPTION
Wall Color
Auto Keystone
Corrects the projected picture’s color when the projection surface is
not white. See "Using Wall Color" on page 33 for details.
There are four options to set the image's aspect ratio depending
on your input signal source. See "Selecting the aspect ratio" on
page 31 for details.
Auto corrects any keystoning of the image.
Keystone
Corrects any keystoning of the image. See "Correcting keystone"
on page 28 for details.
Aspect Ratio
Picture Mode
See "Selecting a picture mode" on page 32 for details.
Reference Mode
See "Setting the User mode" on page 32 for details.
This function is only available when User is selected.
Brightness
See "Adjusting Brightness" on page 33 for details.
Contrast
See "Adjusting Contrast" on page 33 for details.
Picture Mode
Settings
Color
See "Adjusting Color" on page 33 for details.
Tint
See "Adjusting Tint" on page 33 for details.
This function is only available the system format is NTSC.
Sharpness
See "Adjusting Sharpness" on page 33 for details.
Color Temperature
See "Selecting a Color Temperature" on page 33 for details.
Save Settings
3D Sync Invert
Saves the settings made for User mode.
When you discover the inversion of the image depth, enable this
function to correct the problem.
Source
Shows the current signal source.
Information
Resolution
Shows the native resolution of the input signal.
Color System
Shows input system format, NTSC, PAL, SECAM, or RGB.
38
Operation
http://www.pureglare.com.au
Displaying files with internal memory, USB
Drive and SD card
The projector can display files saved in internal memory or external storage like an SD
card or a USB Drive when you have connected to projector.
To display files:
1.
2.
3.
Turn on the power of the projector and the projector displays the home screen.
Connect the projector to one of the above external memory devices.
Press
/ to select SD card, USB Drive/Wireless Display or internal memory.
4.
Storages are classified into Videos, Photos, Music, Documents menu in home
screen. Press / to select desired item and then press OK to enter different file
browser.
See “WDRT8192 Wireless Dongle Quick Start Guide” for details about the wireless display.
File browser window
Videos
Photos
Music
Documents
You will only see relevant and supported files in each of file browser.
Operation
http://www.pureglare.com.au
39
When playing videos
NAME
OK
/
DESCRIPTION
Play/Pause
Volume
Prev
Next
Menu
Back
Home
Plays or pauses a video.
Volume up/down.
• Plays the previous video.
• Press and hold to rewind the video.
- The rewind speed increases to x2, x4, x8 and x16 at 2second intervals.
• Plays the next video.
• Press and hold to fast forward the video.
- The fast-forward speed increases to x2, x4, x8 and x16
at 2-second intervals.
Open/close video pop-up settings menu.
• Return to upper level of OSD.
• Close video pop-up setting menu.
• Leave current video player and back to video file
browser.
Exit video player and go back to home screen.
Video player pop-up settings menu
The video player pop-up menu provides an on-screen display (OSD) for adjustments when
playing videos.
Using the menu
1.
2.
3.
40
To open the OSD menu, press
on the projector or remote control when the
projection screen is displayed.
When the OSD is displayed, press / to select the desired item and adjust the
settings by using
/ .
To exit the OSD, press
on the projector or remote control again.
Operation
http://www.pureglare.com.au
•
See the table for supported subtitle file types. Refer to "Supported file formats" on page 50.
Menu system
Menu Item
Sub-menu
Options
Wall Color
Off/Light Yellow/Pink/Light Green/
Blue/Blackboard
Screen Settings Auto Keystone
On/Off
Keystone
Picture Mode
Bright/Standard/Cinema/Game/User
Reference Mode
Bright/Standard/Cinema/Game
Brightness
Picture Mode
Settings
Contrast
Color
Tint
Sharpness
Color Temperature
Warm/Normal/Cool
Save Settings
Play Settings
Play Mode
All in folder/One video
Play Order
Normal/Shuffle
Repeat
On/Off
Operation
http://www.pureglare.com.au
41
Description of each menu
FUNCTION
DESCRIPTION
Wall Color
Corrects the projected picture’s color when the projection surface is
not white. See "Using Wall Color" on page 33 for details.
Screen Settings
Auto Keystone
Auto corrects any keystoning of the image.
Keystone
Corrects any keystoning of the image. See "Correcting keystone"
on page 28 for details.
Picture Mode
Pre-defined picture modes are provided so you can optimize your
projector image set-up to suit your program type.
Reference Mode
Selects a picture mode that best suits your need for the image
quality and further fine-tune the image based on the selections
listed on the same page below.
This function is only available when User is selected.
Brightness
Adjusts the brightness of the image.
Contrast
Picture Mode
Settings
Adjusts the degree of difference between dark and light in the image.
Color
Adjusts the color saturation level -- the amount of each color in a
video image.
Tint
Adjusts the red and green color tones of the image.
This function is only available the system format is NTSC.
Sharpness
Adjusts the image to make it look sharper or softer.
Color Temperature
Adjusts the color temperature. Cool makes images appear bluish
white. Normal maintains normal colorings for white. Warm
makes images appear reddish white..
Save Settings
Saves the settings made for User mode.
Play Mode
Lets you choose to play one video or all videos in a folder.
Play Settings
Play Order
Lets you select the playback order of video files.
Repeat
Lets you select whether to repeat video playback.
42
Operation
http://www.pureglare.com.au
When playing music
NAME
OK
/
DESCRIPTION
Play/Pause
Volume
Prev
Next
Menu
Back
Home
Plays or pauses a music.
Volume up/down.
• Plays the previous music.
• Press and hold to rewind the music.
• Plays the next music.
• Press and hold to fast forward the music.
Open/close music pop-up settings menu.
• Return to upper level of OSD.
• Close video pop-up setting menu.
• Leave current music player and back to music file
browser.
Exit music player and go back to home screen.
Music player pop-up settings menu
The music player pop-up menu provides an on-screen display (OSD) for adjustments when
playing music.
Using the menu
1.
2.
3.
To open the OSD menu, press
on the projector or remote control when the
projection screen is displayed.
When the OSD is displayed, press / to select the desired item and adjust the
settings by using
/ .
To exit the OSD, press
on the projector or remote control again.
Operation
http://www.pureglare.com.au
43
Menu system
Menu Item
Options
Play Mode
All in folder/One music
Play Order
Normal / Shuffle
Repeat
On/Off
Description of each menu
44
FUNCTION
DESCRIPTION
Play Mode
Lets you choose to play one music or all music in a folder.
Play Order
Lets you select the playback order of music files.
Repeat
Lets you select whether to repeat music playback.
Operation
http://www.pureglare.com.au
When viewing photos
NAME
OK
DESCRIPTION
Play/Pause
Prev
Next
Menu
Back
Home
Plays or pauses a slideshow.
Previous photo.
Next photo.
Open/close photo pop-up settings menu.
• Return to upper level of OSD.
• Close photo pop-up setting menu.
• Leave current photo player and back to photo file
browser.
Exit photo player and go back to home screen.
Photo viewer pop-up settings menu
The photo view pop-up menu provides an on-screen display (OSD) for adjustments when
viewing photos.
Using the menu
1.
2.
3.
To open the OSD menu, press
on the projector or remote control when the
projection screen is displayed.
When the OSD is displayed, press / to select the desired item and adjust the
settings by using
/ .
To exit the OSD, press
on the projector or remote control again.
Operation
http://www.pureglare.com.au
45
Menu system
Menu Item
Sub-menu
Options
Wall Color
Off/Light Yellow/Pink/Light Green/
Blue/Blackboard
Screen Settings Auto Keystone
On/Off
Keystone
Picture Mode
Bright/Standard/Cinema/Game/User
Reference Mode
Bright/Standard/Cinema/Game
Brightness
Picture Mode
Settings
Contrast
Color
Tint
Sharpness
Color Temperature
Warm/Normal/Cool
Save Settings
Slideshow Speed
Play Settings
Fast/ Normal/ Slow
Slideshow Mode
All in folder / One photo
Slideshow Order
Normal / Shuffle
Repeat
On/Off
Description of each menu
FUNCTION
DESCRIPTION
Wall Color
Corrects the projected picture’s color when the projection surface is
not white. See "Using Wall Color" on page 33 for details.
Screen Settings
Auto Keystone
Auto corrects any keystoning of the image.
Keystone
Corrects any keystoning of the image. See "Correcting keystone"
on page 28 for details.
46
Operation
http://www.pureglare.com.au
Picture Mode
Pre-defined picture modes are provided so you can optimize your
projector image set-up to suit your program type.
Reference Mode
Selects a picture mode that best suits your need for the image
quality and further fine-tune the image based on the selections
listed on the same page below.
This function is only available when User is selected.
Brightness
Adjusts the brightness of the image.
Contrast
Picture Mode
Settings
Adjusts the degree of difference between dark and light in the image.
Color
Adjusts the color saturation level -- the amount of each color in a
video image.
Tint
Adjusts the red and green color tones of the image.
This function is only available the system format is NTSC.
Sharpness
Adjusts the image to make it look sharper or softer.
Color Temperature
Adjusts the color temperature. Cool makes images appear bluish
white. Normal maintains normal colorings for white. Warm
makes images appear reddish white..
Save Settings
Slideshow
Speed
Saves the settings made for User mode.
Lets you select slideshow speed.
Slideshow
Mode
Lets you choose to slideshow one photo or all photos in a folder.
Slideshow
Order
Lets you select the slideshow order of photo files.
Repeat
Lets you select whether to repeat slideshow.
Operation
http://www.pureglare.com.au
47
When viewing documents
NAME
OK
Enter
Up
Down
Left
Right
Menu
Back
Home
48
DESCRIPTION
Enlarge the current page. Magnify the page with a further
press.
1.
When the page is not enlarged:
/ : Move to the previous page.
/ : Move to the next page.
2.
When the page is enlarged:
/ / / : Move to the top/down/left/right portion of the
page.
Bring out the pop-up menu.
Leave current document viewer and back to document file
browser.
Exit document viewer and go back to home screen.
•
Loading time may be longer for large files.
•
Document viewer may not work properly when a file does not comply with standards or it is
damaged.
•
Document viewer may not work when a file contains too much data to display on a screen.
(For example, too much data on one sheet in an Excel file.)
•
Document viewer supports only one font. If a screen uses other fonts, the image Media Play
displays may be different than the original screen.
•
For example:
•
1. The position of line breaks in a sentence might be dissimilar.
•
2. The position of page breaks in a MS Word document might be changed. In this case, the
document might be shown incompletely according to the Layout properties for Picture or
Shapes or Object in MS word . (Please refer to the manual of MS Word for more
information on the Layout properties.)
•
Some functions supported on your PC are not supported by the projector, such as these
PowerPoint functions: Animation, 3D, Smart Art, Hyper Link, and Transparency and
Gradation.
•
This product does not support encrypted files (DRM).
Operation
http://www.pureglare.com.au
Document viewer pop-up settings menu
The document view pop-up menu provides an on-screen display (OSD) for adjustments
when viewing photos.
Using the menu
1.
2.
3.
To open the OSD menu, press
on the projector or remote control when the
projection screen is displayed.
When the OSD is displayed, press / to select the desired item and adjust the
settings by using
/ .
To exit the OSD, press
on the projector or remote control again..
Menu system
Menu Item
Options
Page Navigation
Aspect Ratio
Fit to Width / Fit to Height
Description of each menu
FUNCTION
Page
Navigation
Aspect Ratio
DESCRIPTION
Goes directly to a specific page.
Enter a page number using the / / / buttons, check the
page number in the preview window on the upper right corner of
the screen, and then select <Go> to move to that page.
Fit to Width displays a document so that it fits the screen
width.
Fit to Height displays a document so that it fits the screen
height.
Operation
http://www.pureglare.com.au
49
Supported file formats
•
Document, Photo, Music
ITEM
FILE EXTENSION
Adobe PDF 1.0~1.4 (PDF)
MS PowerPoint 97~2010 (ppt, pptx)
MS Excel 95~2010, Office XP (xls, xlsx)
MS Word 95~2010, Office XP (doc, docx)
JPG (.jpg, .jpeg) , BMP (.bmp)
MP3, MP2, MP1, OGG, AAC, WAV
Document
Photo
Music
•
Video, Subtitles
ITEM
FILE EXTENSION
Video
AVI (Xvid, MJPEG), MKV
(XVID), DVIX (MJPEG, XVID),
DAT (MPEG1), MPG(MPEG1),
MPEG(MPEG1)
DESCRIPTION
•
•
Subtitles
SRT (.srt)
•
Subtitle files must be in the same
directory as the video files.
The name of subtitle files shall be
the same as the name of video
files.
SRT only supports for UTF
(unicode 8).
Bit rate range : If peak bit rate of a video file is larger than 10MB, it might cause video
playback lag.
Please visit BenQ.com to know more details about the latest supported formats.
50
Operation
http://www.pureglare.com.au
Using USB streaming
The projector supports USB streaming for USB display and USB file transfer.
BenQ EZ USB display
The projector can project computer screen via a USB cable instead of a VGA cable.
To use USB display:
1.
2.
3.
4.
5.
6.
7.
Connect the projector to a computer using a USB cable.
Turn on the power of the projector and your
source device. The projector displays the home
screen.
Press
/ to select USB Streaming.
Press / to select USB Display and then
press OK to enter.
If your computer can automatically install USB
driver, you can see computer’s screen.
If computer's screen can't be projected, please go to "My Computer", find the
“BenQUSB EZ Display” (same as using a flash disk drive), then run the “Autorun.exe”
file.
Press
or
to leave computer projection screen and back to projector home
screen.
System requirements
CPU
Windows
Graphic card
OS
DRAM
CPU
Graphic card
Mac
OS
DRAM
Recommended Models
Intel/AMD Dual Core 2 GHz or
higher (ATOM not supported)
Intel, nVIDIA or AMD graphic card
with 64MB VRAM or above
Windows XP Professional SP3, Vista
SP3, Windows 7 SP2
1 GB DDR
Intel Dual Core 1.4 GHz or higher
(PowerPC not supported)
Intel, nVIDIA or AMD graphic card
with 64MB VRAM or above
Mac OS X 10.6.5 and above
1 GB DDR
MacBook after 2009-01-21
All series of MacBook Pro
MacBook Air after 2010-06-08
USB file transfer
You can connect the projector to transfer files from your computer to the projetor. The
files will be saved in the internal menory, and you can project images from the projector.
To use USB file transfer:
1.
Connect the projector to a computer using a USB cable.
Operation
http://www.pureglare.com.au
51
2.
Turn on the power of the projector and your
source device. The projector displays the home
screen.
3.
Press
/ to select USB Streaming.
4.
Press / to select USB File Transfer and
then press OK to enter.
5.
If the connection is sucessful, you will see “It is
in USB file transfer mode.” message on the
screen.
6.
Look for a new “removable disk” icon. This “removable disk” is actually the internal
memory in your projector.
7.
Copy & Paste or Drag-N-Drop files from your computer to the removable disk.
8.
If you want to display those files, use
/ to select Internal Memory. See
"Displaying files with internal memory, USB Drive and SD card" on page 39 for
details.
9.
Press
or
to leave USB File Transfer mode and back to projector home screen.
To disconnect the projector from a PC:
Make sure to end the connection properly to prevent damage to the projector or your
data.
52
1.
2.
3.
Click on the Windows Taskbar.
Click the pop-up message.
Disconnect the USB cable only when the message says that it is safe to remove the
hardware.
•
Do not disconnect the USB cable while the files are being copied, as this could result in loss
of data or damage to the projector.
•
The connection will not end if you have projector files open on the PC. Close all projector
files and try again.
•
Other versions of Windows operate similarly. Follow the correct procedure for removing a
USB device from your PC safely for your version of Windows.
Operation
http://www.pureglare.com.au
Using wireless streaming
Display PC screen to projector wirelessly
BenQ EZ QPresenter is a power program to project your PC/NB screen to projector
wirelessly. It also brings you extension display function so that you can show different
content in the secondary display.
Follow the steps below to get it all set up in just a few minutes.
1.
Connect the wireless dongle to the USB jack of the projector.
2.
Select “USB Drive/Wireless Streaming” by pressing
and press “OK” on
your projector. Choose “PC Display”.
Operation
http://www.pureglare.com.au
53
3.
4.
You will be prompted to the “To install BenQ EZ QPresenter” page and follow
the steps as instructed.
Select “BenQ GP10” as your
5.
WLAN connection on your
computer (make sure your computer
is equipped with wireless network
Start a web browser and key in IP
address 192.168.100.10 into the
address bar and press “Enter”.
card).
54
Operation
http://www.pureglare.com.au
6.
Select OS version and start downloading and installing BenQ EZ QPresenter by
following the on-screen instructions on you PC.
7.
Open BenQ EZ QPresenter to start wireless projection
i. Select “BenQ GP10” from wireless access point menu of your PC/NB.
ii. Open BenQ EZ QPresenter to start projection in mirror mode (default).
Tips:
•
If you have installed BenQ EZ QPrensenter prior to step i., it will be connected
to GP10 automatically.
•
You can disable or enable audio streaming baed on your preferences.
Frequently Asked Questions
•
•
•
•
Q: Why does my CPU become busier after launching the BenQ EZ
QPrensenter?
A: BenQ EZ QPresenter counts on your PC CPU to encode the screen images to
reduce the data that needs to be transferred to the receiver. Hence there will be some
overhead to your PC. In general, for a 4+ ranking PCs, it would need up to 30% of CPU
overhead to perform wireless display.
Q: Why can’t I project my screen?
A: BenQ EZ QPresenter needs to access the network connection at some point. As a
result, when your Anti-virus or network security software prompts you for permission
to allow the sender software to access the network, please grant access to proceed, or
choose “add rule” to the fire wall settings.
Operation
http://www.pureglare.com.au
55
•
•
Q: Why does my display frame rate slow down?
A: BenQ EZ QPresenter needs to encode display content while sending massive realtime data to the projector.
i. PC: A dual core PC (excluding Atom processors) or Mac is required to encode
the screen images at 30FPS (Frame Per Second) speed. However, if you would
like to increase the FPS speed, you can:
a. Use better media players, such as GOM player
b. Close all unused apps
c. Use a faster PC with Windows Experience Score higher than 4 (4+ recommended)
ii. Network:
Using 802.11n WiFi
a. Move your laptop closer to the projector
b. Disable the “Minimum Power Consumption” option from the “Advanced Tab” in
your WiFi network Adopter Property setting
c. Lower PC screen resolution
System Requirements for PC Wireless Display
CPU
Graphic card
Windows
OS
Wi-Fi
CPU
Graphic card
Mac
OS
Recommended
Models
Wi-Fi
56
Intel/AMD Dual core 2 GHz or higher (ATOM not
supported)
Intel, NVIDIA or AMD graphic card with 64MB VRAM
or above
Windows XP Professional SP3, Vista SP3, Windows 7
SP2
802.11n
Intel Dual core 1.4 GHz or higher (PowerPC not
supported)
Intel, NVIDIA or AMD graphic card with 64MB VRAM
or above
Mac OS X 10.6.5 and above
MacBook after 2009-01-21
All series of Macbook Pro
Macbook Air after 2010-06-08
802.11n
Operation
http://www.pureglare.com.au
Display iPhone/iPAD content to projector wirelessly
BenQ GP10 QPresenter is an easy-to-use app which enables your mobile devices to
project the display to BenQ GP10 Ultra Lite LED projector. You can display your photos/
documents including PDF, MS-Office and iWorks.
Follow the steps below to get it all set up in just a few minutes.
1.
2.
Connect the wireless dongle to the USB jack of the projector.
Select “USB Drive/Wireless Streaming” by pressing and press “OK” on
your projector. Choose “Mobile Display”.
3.
You will be prompted to the “Mobile Display” welcome page.
Please download GP10 QPresenter in App store and install on your iPhone or iPad.
Operation
http://www.pureglare.com.au
57
4.
Connect your iPhone or iPad to NB/PC. Open iTunes and sync the documents from
NB/PC to your iPhone or iPad. After it’s done, you can disconnect your iPhone/iPad.
5.
Turn on your iPhone/iPad WiFi , find BenQ GP10 or the projector SSID you defined
to projector and connect with it directly. After WiFi connection is established, you
can execute BenQ GP10 QPresenter app on your iPhone/iPad, and you will be able
to see the device’s IP address now. Click it to enjoy BenQ GP10 QPresenter’s
complete functions!!
Features of GP10 QPresenter:
i. View MS-Office files (Word, Excel, PowerPoint), Adobe PDF, Apple iWorks
(Pages, Numbers, Keynote), and it also supports Sketch function and save to
photo roll.
ii. View local photo gallery and do sketch.
Supported device:
i. iPhone 4 and iPhone 4S, iPhone 5
ii. iPad 2, and New iPad (gen 3 iPad)
Supported file format:
PDF: Adobe PDF 1.6 or later
Photo: JPEG/JPG/PNG
Office: MS Office 2003 or later
iWorks: iWorks’ 09 (Pages’ 09, Numbers’ 09, Keynote’ 09)
Not support:
Animation and embedded object in MS-Office or iWorks
58
Operation
http://www.pureglare.com.au
Wi-Fi Dongle Specifications
Model Name
Wireless Standard
Interface
Data Transfer Rate
Frequency Band
Security
Supported OS
Minimum PC System Requirement
WDRT8192
IEEE 802.11 b/g/n
USB 2.0
up to 300Mbps
2.4GHz ISM Band
64 bit/128 bit WEP, TKIP, AES, WPA, WPA2
Windows 2000/XP/Vista/7
CPU: 200MHz or above
RAM: 64MB RAM or above, 128MB recommended
Operation
http://www.pureglare.com.au
59
Using settings menu
This menu is to set the projector’s operating environment.
Using the menu
1.
2.
3.
4.
5.
6.
7.
60
To open the OSD menu, press
/ to select Settings icon in home screen.
When the OSD is displayed, press / to select any item in the main menu.
After selecting the desired main menu item, press OK to enter the feature settings
submenu.
Press / to select the desired item and press OK to open the pop-up menu.
Select the settings using / / / and press OK to confirm. Once the setting is
selected, the OSD menu returns to the selected item.
Press
to return to the main menu.
You may press
to go back to home screen directly.
Press
again to go back to home screen.
Operation
http://www.pureglare.com.au
Menu system
Main menu
Sub-menu
Options
Language
1.
Basic
LED Mode
Normal/Eco
Wall Color
Off/Light Yellow/Pink/Light Green/
Blue/Blackboard
Auto Keystone
On/Off
Eye Protection
On/Off
Auto Power Off
Disable/5 min/10 min/15 min/20
min/25 min/30 min
Splash Screen
BenQ/ Black/Blue
High Altitude Mode
Audio Settings
On/Off
SRS HD
On/Off
Mute
On/Off
Volume
Power on/off ring
tone
Menu Display Time
2.
Advanced
On/Off
5 sec/10 sec/15 sec/20 sec/25 sec/
30 sec
Change Password
Recall Password
Security Settings
Closed Caption
Change Security
Settings
Power On Lock
On/Off
Closed Caption
Enable
On/Off
Caption Version
CC1/CC2/CC3/CC4
Test Pattern
Firmware Upgrade
Reset All Settings
Source
Picture Mode
Color System
3.
Information
Resolution
Memory / Internal Memory
DLP 3D
LED Lamp Life
Firmware Version
Operation
http://www.pureglare.com.au
61
Description of each menu
FUNCTION
Language
LED Mode
Wall Color
1. Basic menu
Auto
Keystone
Eye
Protection
Auto Power
Off
DESCRIPTION
Sets the language for the On-Screen Display (OSD) menus.
Choose Eco to dim the projector LED which will lower power
consumption, extend the LED life and reduce noise. Choose
Normal to return normal mode.
Corrects the projected picture’s color when the projection surface is
not white.
Auto corrects any keystoning of the image.
When detecting something is in front of the projection lens, the
projector automatically hides the image. The effective range is 20 cm30 cm (varies with different ambient light and colors of reflected
objects). See "Hiding the image" on page 28 for details on how to
restore the image.
Allows the projector to turn off automatically if no input signal is
detected after a set period of time.
Allows you to select which logo screen will display during projector
Splash Screen start-up. Three options are available: BenQ logo, Black screen, or
Blue screen.
62
Operation
http://www.pureglare.com.au
FUNCTION
DESCRIPTION
High Altitude A mode for operation in high altitude areas. See "Operating in a high
altitude environment" on page 34for details.
Mode
Audio
Settings
See "Adjusting the sound" on page 34 for details.
Menu Display Sets the length of time the OSD will remain active after your last key
press. The range is from 5 to 30 seconds in 5-second increments.
Time
Security
Settings
See "Securing the projector" on page 29 for details.
2. Advanced menu
Closed Caption Enable
Activates the function by selecting On when the selected input signal
carries closed captions.
Closed
Caption
•
Captions: An on-screen display of the dialogue, narration, and
sound effects of TV programs and videos that are closed
captioned (usually marked as "CC" in TV listings).
Caption Version
Test Pattern
Firmware
Upgrade
Reset All
Settings
Selects a preferred closed captioning mode. To view captions, select
CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary
language in your area).
Selecting OK enables the function and the projector displays the grid
test pattern. It helps you adjust the image size and focus and check
that the projected image is free from distortion.
Updating the latest firmware are only allowed via an SD card.
Returns all settings to the factory preset values.
Operation
http://www.pureglare.com.au
63
FUNCTION
Source
DESCRIPTION
Shows the current signal source.
Picture Mode Shows the selected mode.
Color System Shows input system format: RGB or YUV.
3. Information menu
64
Resolution
Shows the native resolution of the input signal.
Memory /
Internal
Memory
Shows the memory capacity status: Internal Memory.
DLP 3D
Shows the DLP 3D status.
LED Lamp
Life
Displays the number of hours the lamp has been used.
Firmware
Version
Shows firmware version.
Operation
http://www.pureglare.com.au
Shutting down the projector
1.
Press II Power and a confirmation message
displays prompting you.
If you don't respond in a few seconds, the
message will disappear.
2.
3.
Press II Power a second time.
The Power LED indicator flashes orange
slowly and fans stop.
Disconnect the power cord from the wall socket if the projector will not be used in
an extended period of time.
4.
Operation
http://www.pureglare.com.au
65
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis
is to keep the lens clean.
Never remove any parts of the projector. Contact your dealer if other parts need
replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
•
•
Use a canister of compressed air to remove dust.
If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens
cleaner and gently wipe the lens surface.
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as
described in "Shutting down the projector" on page 65 and unplug the power cord.
•
•
To remove dirt or dust, wipe the case with a soft, lint-free cloth.
To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions
below:
•
•
•
•
Make sure the temperature and humidity of the storage area are within the
recommended range for the projector. Please refer to "Specifications" on page 69 or
consult your dealer about the range.
Retract the adjuster feet.
Remove the battery from the remote control.
Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent.
66
Maintenance
http://www.pureglare.com.au
LED Indicators
Status / Problems
LED indicators
LED Behavior
Power
Fan
Temp
Standby
Orange
solid on
Off
Off
Power LED slow flash
Power warm up
Green
blanking
Power on
Green
Off
Off
Light solid on sequence:
Power->Key->Ring & OK
Cooling
Orange
blanking
Off
Off
Power LED slow flash
Fan1 error
Off
On
Off
Ring & OK LED flash first and
then key LED flash (1.5 seconds
interval)
Temp error
Off
Off
On
Ring & OK LED and Key LED
flash at the same time (1.5
seconds interval for LED flash)
Maintenance
http://www.pureglare.com.au
67
Troubleshooting
The projector does not turn on.
Cause
Remedy
Plug the AC adapter into the DC IN socket on the
projector, plug the power cord into the AC inlet
There is no power from the power cable. on the AC adapter, plug the power cord into the
power outlet. If the power outlet has a switch,
make sure that it is switched on.
Attempting to turn the projector on again Wait until the cooling down process has
during the cooling process.
completed.
No picture
Cause
Remedy
The source is not turned on or
connected correctly.
Turn the source on and check that the signal cable
is connected correctly.
The projector is not correctly connected
to the input signal device.
Check the connection.
The input signal has not been correctly
selected.
Select the correct input signal with the
on the projector or remote control.
/
key
Blurred image
Cause
Remedy
The projection lens is not correctly
focused.
Adjust the focus of the lens using the focus ring.
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as well
as the height of the unit if necessary.
Remote control does not work
Cause
Remedy
The battery is out of power.
Replace the battery with new one.
There is an obstacle between the remote
control and the projector.
Remove the obstacle.
You are too far away from the projector.
Stand within 7 meters (23 feet) of the projector.
The password is incorrect
68
Cause
Remedy
You do not remember the password.
Please see "Entering the password recall
procedure" on page 30 for details.
Troubleshooting
http://www.pureglare.com.au
Specifications
Projector specifications
All specifications are subject to change without notice.
General
Product name
Model name
Ultra Lite LED Projector
GP10
Optical
Resolution
Display system
Lens F/Number
Lamp
Throw Ratio
1280 x 800 WXGA
1-CHIP DMD
F = 1.65
3LED
1.2:1 (40"@1m)
Electrical
Power supply
Power consumption
Keystone Adjustment
AC100–240V, 50-60 Hz (Automatic)
125 W (Max.); < 0.5 W (Standby)
1D, Vertical +/- 30 degrees
Mechanical
Dimensions
Weight
220 mm (W) x 61.8 mm (H) x 177 mm (D)
1.5 kg
Input terminal
Multi-input
Computer input
Video input
HDMI
Audio input
USB-A type
mini-B USB type
SD card slot
Internal memory
D-Sub 15-pin (female) x 1
VIDEO
RCA jack x 1
SD/HDTV signal input
Analog - Component RCA jack x 3 (through RGB input)
HDMI x1
3.5 mm stereo mini jack x 1
For USB flash drive. Supports videos/photos/music/
documents.
Supports USB display and USB file transfer
Supports videos/photos/music/documents
2GB
Output terminal
Audio output
Speaker
3.5 mm stereo mini jack x 1
3 watt x 2
Environmental Requirements
Operating temperature
0° C- 40° C at sea level
Specifications
http://www.pureglare.com.au
69
Operating relative
humidity
Operating altitude
10%-90% (without condensation)
0–1499 m at 0°C–35°C
1500–3000 m at 0°C–30°C (with High Altitude Mode on)
Dimensions
•
•
Without DVD player: 220 mm (W) x 61.8 mm (H) x 177 mm (D)
With DVD player: 220 mm (W) x 95.0 mm (H) x 177 mm (D)
220
61.8
220
177
81
29
81
62.2
95.0
Unit: mm
70
Specifications
http://www.pureglare.com.au
Timing chart
Supported timing for PC input
Resolution
640 x 480
720 x 400
800 x 600
1024 x 768
1152 x 864
1024 x 576
1024 x 600
1280 x 720
1280 x 768
1280 x 800
1280 x 1024
1280 x 960
1360 x 768
1440 x 900
1400 x 1050
1680 x 1050
640 x 480
@67Hz
832 x [email protected]
1024 x
[email protected]
1152 x
[email protected]
Vertical
Frequency (Hz)
Mode
VGA_60
VGA_72
VGA_75
VGA_85
720 x 400_70
SVGA_60
SVGA_72
SVGA_75
SVGA_85
SVGA_120*
XGA_60
XGA_70
XGA_75
XGA_85
XGA_120* (Reduce
Blanking)
1152 x 864_75
BenQ Notebook
Timing
BenQ Notebook
Timing
1280 x 720_60
1280 x 768_60
WXGA_60
WXGA_75
WXGA_85
WXGA_120*
(Reduce Blanking)
SXGA_60
SXGA_75
1280 x 960_60
1280 x 960_85
1360 x 768_60
WXGA+_60
SXGA+_60
1680 x 1050_60
Horizontal
Frequency (kHz)
59.940
72.809
75.000
85.008
70.087
60.317
72.188
75.000
85.061
119.854
60.004
70.069
75.029
84.997
31.469
37.861
37.500
43.269
31.469
37.879
48.077
46.875
53.674
77.425
48.363
56.476
60.023
68.667
119.989
97.551
75.00
67.500
60.0
35.820
64.995
41.467
60
45.000
59.870
59.810
74.934
84.880
47.776
49.702
62.795
71.554
119.909
101.563
60.020
75.025
60.000
85.002
60.015
59.887
59.978
59.954
63.981
79.976
60.000
85.938
47.712
55.935
65.317
65.290
MAC13
66.667
35.000
MAC16
74.546
49.722
MAC19
75.020
60.241
MAC21
75.06
68.68
*Supported timing for 3D signal with frame sequential format.
Specifications
http://www.pureglare.com.au
71
Supported timing for HDMI input
PC timings:
Resolution
640 x 480
720 x 400
800 x 600
1024 x 768
1152 x 864
1024 x 576
1024 x 600
1280 x 720
1280 x 768
1280 x 800
1280 x 1024
1280 x 960
1360 x 768
1440 x 900
1400 x 1050
1680 x 1050
640 x [email protected]
832 x [email protected]
1024 x
[email protected]
1152 x
[email protected]
Vertical
Frequency (Hz)
Mode
VGA_60
VGA_72
VGA_75
VGA_85
720 x 400_70
SVGA_60
SVGA_72
SVGA_75
SVGA_85
SVGA_120*
XGA_60
XGA_70
XGA_75
XGA_85
XGA_120* (Reduce
Blanking)
1152 x 864_75
BenQ Notebook
Timing
BenQ Notebook
Timing
1280 x 720_60
1280 x 768_60
WXGA_60
WXGA_75
WXGA_85
WXGA_120*
(Reduce Blanking)
SXGA_60
SXGA_75
1280 x 960_60
1280 x 960_85
1360 x 768_60
WXGA+_60
SXGA+_60
1680 x 1050_60
MAC13
MAC16
59.940
72.809
75.000
85.008
70.087
60.317
72.188
75.000
85.061
119.854
60.004
70.069
75.029
84.997
31.469
37.861
37.500
43.269
31.469
37.879
48.077
46.875
53.674
77.425
48.363
56.476
60.023
68.667
119.989
97.551
75.00
67.500
60.000
35.820
64.995
41.467
60
59.870
59.810
74.934
84.880
45.000
47.776
49.702
62.795
71.554
119.909
101.563
60.020
75.025
60.000
85.002
60.015
59.887
59.978
59.954
66.667
74.546
63.981
79.976
60.000
85.938
47.712
55.935
65.317
65.290
35.000
49.772
MAC19
75.020
60.241
MAC21
75.06
68.68
*Supported timing for 3D signal with frame sequential format.
72
Horizontal
Frequency (kHz)
Specifications
http://www.pureglare.com.au
Video timings:
Timing
480i
480p
576i
576p
720/50p
720/60p
1080/24P
1080/25P
1080/30P
1080/50i
1080/60i
1080/50P
1080/60P
Resolution
Vertical
Frequency (Hz)
720 (1440) x 480
720 x 480
720 (1440) x 576
720 x 576
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
Horizontal
Frequency (kHz)
59.94
59.94
50
50
50
60
24
25
30
50
60
50
60
15.73
31.47
15.63
31.25
37.5
45.00
27
28.13
33.75
28.13
33.75
56.25
67.5
Supported timing for Component-YPbPr input
Timing
480i
480p
576i
576p
720/50p
720/60p
1080/50i
1080/60i
1080/24P
1080/25P
1080/30P
1080/50P
1080/60P
Resolution
Vertical
Frequency (Hz)
720 x 480
720 x 480
720 x 576
720 x 576
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
59.94
59.94
50
50
50
60
50
60
24
25
30
50
60
Horizontal
Frequency (kHz)
15.73
31.47
15.63
31.25
37.5
45.00
28.13
33.75
27
28.13
33.75
56.25
67.5
Supported timing for Video input
Video mode
NTSC
PAL
SECAM
PAL-M
PAL-N
PAL-60
NTSC4.43
Vertical Frequency
(Hz)
60
50
50
60
50
60
60
Horizontal Frequency
(kHz)
15.73
15.63
15.63
15.73
15.63
15.73
15.73
Specifications
http://www.pureglare.com.au
73
Warranty and Copyright information
Patents
This BenQ projector is covered by the following patents:
U.S. patents 6,837,608; 7,275,834; 7,181,318; TW patents 202690; 205470; I228635;
I259932; China Patents ( 中国发明专利 ) ZL01143168.7; ZL03119907.0;
ZL200510051609.2
Limited warranty
BenQ warrants this product against any defects in material and workmanship, under
normal usage and storage.
Proof of purchase date will be required with any warranty claim. In the event this product
is found to be defective within the warranty period, BenQ's only obligation and your
exclusive remedy shall be replacement of any defective parts (labor included). To obtain
warranty service, immediately notify the dealer from which you purchased the product of
any defects.
Important: The above warranty shall be void if the customer fails to operate the product in
accordance with BenQ's written instructions, especially the ambient humidity must be inbetween 10% and 90%, temperature in-between 0°C and 35°C, altitude lower than 4920
feet, and avoiding to operate the projector in a dusty environment. This warranty gives you
specific legal rights, and you may have other rights which vary from country to country.
For other information, please visit www.BenQ.com.
Copyright
© 2012 BenQ Corp. Specification may vary by region, please visit your local stores for
details. Actual product’s features and specifications are subject to change without notice.
This material may include corporate names and trademarks of third parties which are the
properties of the third parties respectively. Apple, the Apple logo, iPad, iPhone, iPod, iPod
classic, iPod nano, iPod shuffle, and iPod touch are trademarks of Apple Inc., registered in
the U.S. and other countries.
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves
the right to revise this publication and to make changes from time to time in the contents
hereof without obligation to notify any person of such revision or changes.
*DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others
are copyrights of their respective companies or organizations.
74
Warranty and Copyright information
http://www.pureglare.com.au
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement