72129A ZYYT | Motorola 72128A XT, 72129A XT, ZYYT Ethernet Switch User's Manual

72128A, 72129A Hardened Managed Ethernet Switch

Preface

This manual describes how to install and use the 72128A and

72129A Hardened Managed Ethernet Switch. This switch introduced here is designed to deliver full scalability with

SNMP/RMON web-based management functions by providing:

72128AX T

72129AX T

12-port 10/100Base-TX + 1-port Gigabit

Hardened Managed Ethernet Switch




72129A-Z YY T


Gigabit Options:

X

= 1 : 1000Base-SX (SC)

2 : 10/100/1000Base-TX

YY

= DA : Combination of 1-port 10/100/1000Base-TX and 1-port 1000Base-SX (SC)

Power Type:

T

= Terminal Block power input

To get the most out of this manual, you should have an understanding of Ethernet networking concepts.

In this manual, you will find:

Features on the 72128A and 72129A Hardened Managed Ethernet Switch z Illustrative LED functions z Installation z

Management z SNMP, DHCP, IGMP… z Specifications

User’s Manual 1


Table of Contents

P

REFACE

T

ABLE OF

C

ONTENTS

1

2

P

RODUCT

O

VERVIEW

M

ANAGED

E

THERNET

S

WITCH

P

ACKAGE

C

ONTENTS

P

RODUCT

H

IGHLIGHTS

Basic Features

Management Support

F

RONT

P

ANEL

D

ISPLAY

P

HYSICAL

P

ORTS

S

WITCH

M

ANAGEMENT

Web-based browser interface

Administration console via RS-232 serial port (CLI)

External SNMP-based network management application

I

NSTALLATION

10

S

ELECTING A

S

ITE FOR THE

S

WITCH

10

C

ONNECTING TO

P

OWER

10

DC Terminal Block power input 10

C

ONNECTING TO

Y

OUR

N

ETWORK

11

Cable Type & Length

Cabling

11

12

4

5

7

8

9

4

4

5

5

9

9

9

S

WITCH

M

ANAGEMENT

13

M

ANAGEMENT

A

CCESS

O

VERVIEW

13

A

DMINISTRATION

C

ONSOLE

(CLI) 14

Direct Access

Modem Access

14

15

W

EB

M

ANAGEMENT

15

SNMP-B

ASED

N

ETWORK

M

ANAGEMENT

15

P

ROTOCOLS

16

M

ANAGEMENT

A

RCHITECTURE

16

W

EB

-B

ASED

B

ROWSER

M

ANAGEMENT

17

SNMP & RMON M

ANAGEMENT

18

O

VERVIEW

18

SNMP A

GENT AND

MIB-2 (RFC 1213) 18

RMON MIB (RFC 1757)

AND

B

RIDGE

MIB (RFC 1493) 19

RMON Groups Supported

Bridge Groups Supported

19

20

2 User’s Manual


W

EB

-B

ASED

B

ROWSER

M

ANAGEMENT

21

L

OGGING ON TO THE SWITCH

21

U

NDERSTANDING THE

B

ROWSER

I

NTERFACE

23

S

YSTEM

25

P

ORT

34

S

WITCHING

39

T

RUNKING

42

STP 43

VLAN 45

Q

O

S 51

SNMP 54

O

THER

P

ROTOCOLS

59

C

OMMAND

L

INE

C

ONSOLE

M

ANAGEMENT

62

A

DMINISTRATION

C

ONSOLE

62

Exec Mode (View Mode) 63

Privileged Exec Mode (Enable Mode)

Configure Mode (Configure Terminal Mode)

67

71

S

YSTEM

75

P

ORT

82

S

WITCHING

86

T

RUNKING

91

STP 92

VLAN 99

Q

O

S 105

SNMP 108

O

THER

P

ROTOCOLS

116

S

PECIFICATIONS

124

A

PPENDIX

126



Product Overview

Managed Ethernet Switch

Front View

Package Contents

When you unpack the product package, you shall find the items listed below. Please inspect the contents, and report any apparent damage or missing items immediately to your authorized reseller.

•

The Managed Ethernet Switch

Manual

• RS232

•

Panel-mount brackets with screws



Product Highlights

Basic Features

z Complies with NEMA TS1 & TS2 Environmental requirements for Traffic control equipment z Complies with EN61000-6-2 EMC Generic standard immunity for

Industrial environment z Supports 8192 MAC addresses z Provides 256K Bytes memory buffer z Auto-negotiation for speed and duplexity on all TX ports z Auto-MDIX on all TX ports z Full wire-speed forwarding rate z Store-and-forward z Half-duplex back-pressure and IEEE802.3x full-duplex compliant flow control z Power input: 24VDC (Terminal Block) z -40℃ to 75℃ (-40℉ to 167℉) operating temperature range

Tested for functional operation @ -40℃ to 85℃ (-40℉ to 185℉) z Front panel reset button z Front panel port status LEDs z

Hardened aluminum case z Supports DIN-Rail, Panel, Rack Mounting installation

Management Support

VLAN

z VLAN z IEEE802.1Q tagged VLAN

TRUNKING

z MAC-based Trunking with automatic link fail-over

PORT-SECURITY

z Per-port programmable MAC address locking z Up to 24 Static Secure MAC addresses per port

PORT-MIRRORING

z Port-mirroring

QOS

(IEEE802.1p Quality of Service) z 4 priority queues

INTERNETWORKING PROTOCOLS

z Bridging:



IEEE802.1w Rapid Spanning Tree

IEEE802.1D Spanning Tree compatible

IEEE802.1Q – GVRP z IP z Rate

IGMP Snooping

Control

NETWORK MANAGEMENT METHODS

z Console port access via RS-232 cable (CLI, Command Line Interface) z Telnet remote access z agent:

MIB-2 (RFC1213)

Bridge MIB (RFC1493)

RMON MIB (RFC1757) – statistics, history, alarm and events

VLAN MIB (IEEE802.1Q/RFC2674)

Private MIB z Web z TFTP software-upgrade capability



Front Panel Display

c POWER

This LED comes on when the switch is properly connected to power and turned on. d Port Status LEDs

The LEDs are located at the left side of the front panel, displaying status for each respective port. Please refer to the following table for more details.

10/100TX

Link/ACT

10/100

On

Flashing

On

Off

A valid network connection established

Transmitting or receiving data

ACT stands for ACTIVITY

Communication speed is 100Mbps


10/100/1000TX, 1000SX

On

LNK/ACT

Flashing

1000

On

Off

A valid network connection established

Transmitting or receiving data

ACT stands for ACTIVITY


Communication speed is 10/100Mbps



Physical Ports

The Managed Ethernet Switch provides:

72128AX T

72129AX T






72129A-Z YY T


Gigabit Options:

X

= 1 : 1000Base-SX (SC)

2 : 10/100/1000Base-TX

YY

= DA : Combination of 1-port 10/100/1000Base-TX and 1-port 1000Base-SX (SC)

Power Type:

T

= Terminal Block power input

CONNECTIVITY

z z

SC connectors on 1000SX ports

RJ-45 connectors on TX ports

MODE SELECTION

z

10BaseT full-duplex mode z z z z z

10BaseT half-duplex mode

100BaseTX full-duplex mode

100BaseTX half-duplex mode

1000BaseT/SX full-duplex mode

Auto-negotiating mode



Switch Management

Web-based browser interface

The switch also boasts a point-and-click browser-based interface that lets user access full switch configuration and functionality from a

Netscape or Internet Explorer browser.

Administration console via RS-232 serial port (CLI)

The switch provides an onboard serial port, which allows the switch to be configured via a directly connected terminal.

External SNMP-based network management application

The switch can also be configured via SNMP.



Installation

This chapter gives step-by-step instructions about how to install the switch:

Selecting a Site for the Switch

As with any electric device, you should place the switch where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference. Specifically, the site you select should meet the following requirements:

-The ambient temperature should be between -40°C to 75℃ (-40℉ to

167℉).

-The relative humidity should be less than 95 percent, non-condensing.

-Surrounding electrical devices should not exceed the electromagnetic field

(RFC) standards.

-Make sure that the switch receives adequate ventilation. Do not block the ventilation holes on each side of the switch.

Connecting to Power

DC Terminal Block power input

Step 1: Connect the supplied DC power cord to the terminal block on the back of the switch, and then plug it into a standard DC outlet with a voltage 24 VDC. Turn on the DC power supply.

Step 2: Turn off the DC power supply if you want to shut down the switch.

Rear view

10 User ’s Manual


Connecting to Your Network

Cable Type & Length

It is necessary to follow the cable specifications below when connecting the switch to your network. Use appropriate cables that meet your speed and cabling requirements.

Cable Specifications

Speed Connector Port

Speed

Half/Full

Duplex

Cable Max.

Distance

1000BaseSX

(*Wavelength of

850nm)

SC

UTP/STP

Cat. 3, 4, 5

100 m

Mbps UTP/STP

Cat. 5

100 m

UTP/STP

Cat. 5

2000 Mbps 50 or

62.5/125µm multi-mode fiber

550 m



Cabling

Step 1: First, ensure the power of the switch and end devices are turned off.

<Note>

Always ensure that the power is off before any installation.

Step 2: Prepare cable with corresponding connectors for each type of port in use.

Step 3: Consult Cable Specifications Table on previous page for cabling requirements based on connectors and speed.

Step 4: Connect one end of the cable to the switch and the other end to a desired device.

Step 5: Once the connections between two end devices are made successfully, turn on the power and the switch is operational.



Switch Management

This chapter explains the methods that you can use to configure management access to the switch. It describes the types of management applications and the communication and management protocols that deliver data between your management device (workstation or personal computer) and the system. It also contains information about port connection options.

This chapter covers the following topics:

•

Management Access Overview

•

Key Concepts

•

Key Guidelines for Implementation

•

Web Management Access

•

Administration Console Access

•

SNMP Access

•

Standards, Protocols, and Related Reading

Management Access Overview

The switch gives you the flexibility to access and manage the switch using any or all of the following methods.

The web browser interface and administration console (CLI) support are embedded in the switch software and are available for immediate use.



Administration Console (CLI)

The administration console is an internal, character-oriented,

Command Line Interface (CLI) for performing system administration such as displaying statistics or changing option settings.

Using this method, you can view the administration console from a terminal, personal computer, Apple Macintosh, or workstation connected to the switch’s console port.

There are two ways to use this management method: direct access or modem access. The following sections describe these methods.

Direct Access

Direct access to the administration console is achieved by directly connecting a terminal or a PC equipped with a terminal-emulation program (such as HyperTerminal) to the switch console port.

When using the management method, configure the terminal-emulation program to use the following parameters (you can change these settings after login):

[DEFAULT PARAMETERS]

♦ 115,200bps

♦ 8 data bits

♦ No parity

♦ 1 stop bit

This management method is often preferred because you can remain connected and monitor the system during system reboots. Also, certain error messages are sent to the serial port, regardless of the interface through which the associated action was initiated. A Macintosh or PC attachment can use any terminal-emulation program for connecting to the terminal serial port. A workstation attachment under UNIX can use an emulator such as TIP.



Modem Access

You can access the switch’s administration console from a PC or

Macintosh using an external modem attached to the console port. The switch management program provides Console Port screen, accessible from the Basic Management screen that lets you configure parameters for modem access.

When you have configured the external modem from the administration console, the switch transmits characters that you have entered as output on the modem port. The switch echoes characters that it receives as input on the modem port to the current administration console session.

The console appears to be directly connected to the external modem.

Web Management

The switch provides a browser interface that lets you configure and manage the switch remotely.

After you set up your IP address for the switch, you can access the switch’s web interface applications directly in your web browser by entering the IP address of the switch. You can then use your web browser to list and manage switch configuration parameters from one central location, just as if you were directly connected to the switch’s console port.

SNMP-Based Network Management

You can use an external SNMP-based application to configure and manage the switch. This management method requires the SNMP agent on the switch and the SNMP

Network Management Station to use the same community string. This management method, in fact, uses two community strings: the get community string and the set community string. If the SNMP Network management station only knows the set community string, it can read and write to the MIBs. However, if it only knows the get community string, it can only read MIBs. The default get and set community

strings for the switch are public.



Protocols

The switch supports the following protocols:

VIRTUAL TERMINAL PROTOCOLS, SUCH AS TELNET

A virtual terminal protocol is a software program, such as Telnet, that allows you to establish a management session from a Macintosh, a PC, or a UNIX workstation. Because Telnet runs over TCP/IP, you must have at least one IP address configured on the switch before you can establish access to it with a virtual terminal protocol.

<Note>

Terminal emulation is different from a virtual terminal protocol in that you must connect a terminal directly to the console port.

SIMPLE NETWORK MANAGEMENT PROTOCOL (SNMP)

SNMP is the standard management protocol for multivendor IP networks.

SNMP supports transaction-based queries that allow the protocol to format messages and to transmit information between reporting devices and data-collection programs. SNMP runs on top of the User Datagram Protocol

(UDP), offering a connectionless-mode service.

Management Architecture

All of the management application modules use the same

Messaging Application Programming Interface (MAPI). By unifying management methods with a single MAPI, configuration parameters set using one method (e.g. console port) are immediately displayed the other management methods (e.g. SNMP agent of web browser).

The management architecture of the switch adheres to the

IEEE open standard. This compliance assures customers that the switch is compatible with, and will interoperate with other solutions that adhere to the same open standard.



Web-Based Browser Management

The switch provides a web-based browser interface for configuring and managing the switch. This interface allows you to access the switch using a preferred web browser.

This chapter describes how to configure the switch using its web-based browser interface.



SNMP & RMON Management

This chapter describes the switch’s Simple Network

Management Protocol (SNMP) and Remote Monitoring

(RMON) capabilities.

Overview

RMON is an abbreviation for the Remote Monitoring MIB

(Management Information Base). RMON is a system defined by the Internet Engineering Task Force (IETF) document RFC

1757, which defines how networks can be monitored remotely.

RMONs typically consist of two components: an RMON probe and a management workstation:

- The RMON probe is an intelligent device or software agent that continually collects statistics about a LAN segment or VLAN. The RMON probe transfers the collected data to a management workstation on request or when a pre-defined threshold is reached.

- The management workstation collects the statistics that the RMON probe gathers. The workstation can reside on the same network as the probe, or it can have an in-band or out-of-band connection to the probe.

The switch provides RMON capabilities that allow network administrators to set parameters and view statistical counters defined in MIB-II, Bridge MIB, and RMON MIB. RMON activities are performed at a Network Management Station running an SNMP network management application with graphical user interface.

SNMP Agent and MIB-2 (RFC 1213)

The SNMP Agent running on the switch manager CPU is responsible for:



- Retrieving MIB counters from various layers of software modules according to the SNMP GET/GET NEXT frame messages.

- Setting MIB variables according to the SNMP SET frame message.

- Generating an SNMP TRAP frame message to the Network Management

Station if the threshold of a certain MIB counter is reached or if other trap conditions (such as the following) are met:

WARM START

COLD START

LINK UP

LINK DOWN

AUTHENTICATION FAILURE

RISING ALARM

FALLING ALARM

TOPOLOGY ALARM

MIB-II defines a set of managed objects in various layers of the TCP/IP protocol suites. MIB-II covers all managed objects from layer 1 to layer 4, and, as a result, is the major SNMP

MIB supported by all vendors in the networking industry. The switch supports a complete implementation of SNMP Agent and MIB-II.

RMON MIB (RFC 1757) and Bridge MIB (RFC

1493)

The switch provides hardware-based RMON counters in the switch chipset. The switch manager CPU polls these counters periodically to collect the statistics in a format that complies with the RMON MIB definition.

RMON Groups Supported

The switch supports the following RMON MIB groups defined in RFC 1757:

- RMON Statistics Group – maintains utilization and error statistics for the switch port being monitored.



- RMON History Group – gathers and stores periodic statistical samples from the previous Statistics Group.

- RMON Alarm Group – allows a network administrator to define alarm thresholds for any MIB variable. An alarm can be associated with Low

Threshold, High Threshold, or both. A trigger can trigger an alarm when the value of a specific MIB variable exceeds a threshold, falls below a threshold, or exceeds or falls below a threshold.

- RMON Event Group – allows a network administrator to define actions based on alarms. SNMP Traps are generated when RMON Alarms are triggered. The action taken in the Network Management Station depends on the specific network management application.

Bridge Groups Supported

The switch supports the following four groups of Bridge MIB (RFC 1493):

- The dot1dBase Group – a mandatory group that contains the objects applicable to all types of bridges.

- The dot1dStp Group – contains objects that denote the bridge’s state with respect to the Spanning Tree Protocol. If a node does not implement the

Spanning Tree Protocol, this group will not be implemented. This group is applicable to any transparent only, source route, or SRT bridge that implements the Spanning Tree Protocol.

- The dot1dTp Group – contains objects that describe the entity’s transparent bridging status. This group is applicable to transparent operation only and

SRT bridges.

- The dot1dStatic Group – contains objects that describe the entity’s destination-address filtering status. This group is applicable to any type of bridge which performs destination-address filtering.



Web-Based Browser Management

The switch provides a web-based browser interface for configuring and managing the switch. This interface allows you to access the switch using a preferred web browser.

This chapter describes how to configure the switch using its web-based browser interface.

Logging on to the switch

SWITCH IP ADDRESS

In your web browser, specify the IP address of the switch. Default IP address is 169.254.1.1.

LOGIN

Enter the factory default login ID: root.



PASSWORD

Enter the factory default password (no password).

Or enter a user-defined password if you followed the instructions later and changed the factory default password.

Then click on the “Login” button to log on to the switch.



Understanding the Browser Interface

The web browser interface provides eight groups of point-and-click buttons at the left field of the screen for configuring and managing the switch.

SYSTEM

System Information, System Name/Password, IP Address, Save

Configuration, Firmware Upgrade, Reboot, Logout

PORT

Configuration, Port Status, Rate Control, RMON Statistics, Per Port Vlan

Activities

SWITCHING

Bridging, Static MAC Entry, Port Mirroring

TRUNKING

Port Trunking

STP

Global Configuration, RSTP Port Setting



VLAN

VLAN Mode Setting, 802.1Q VLAN Setting, 802.1Q Port Setting, Port Based

VLAN

QOS

Global Configuration, 802.1p priority, DSCP

SNMP

SNMP General Setting, SNMP v1/v2c, SNMP v3

OTHER PROTOCOLS

GVRP, IGMP Snooping


System




System Name/Password

1. System Name: Click in “System Name” text box. Type a system name if it is blank, or replace the current system name with a new one.

2. Password: Click in “Password” text box. Type a password.

3. Retype Password: Click in “Retype Password” text box. Type the same password in “Password” text box again to verify it.

4. Updating setting: Click “Updating setting” button to update your settings.



IP Address

1. IP Address: Click in “IP Address” text box and type a new address to change the IP Address.

2. IP Subnet Mask: Click in “IP Subnet Mask” text box and type a new address to change the IP Subnet Mask.

3. Submit: Click “Submit” button when you finished these selections.

4. You need to enter the new IP address on the browser and reconnect to the switch after IP or subnet mask are changed.

5. Default Gateway: Click “Default Gateway” drop-down menu to choose

“Disable” or “Enable” from the “Default Gateway” drop-down list to disable or enable Default Gateway Setting for the switch.

Click the text box and type a new address to change the Default

Gateway. (Need to choose “Enable” from the “Default Gateway” drop-down menu.)

6. Submit: Click “Submit” button when you finished Default Gateway.



Save Configuration

1. Load config from TFTP server:

Click in “TFTP Server” text box and type the TFTP server IP address from where the file will be obtained.

Click in “FILE” text box and type the name of the file that will be obtained.

Click “Load” button to load the file from the TFTP server.

2. Backup config to TFTP server:

Click in “TFTP Server” text box and type the TFTP server IP address to where the file will be back upped.

Click in “FILE” text box and type the name of the file that will be back upped.

Click “Backup” button to backup the file to the TFTP server.

3. Save Configuration: Click “Save Configuration” button to save your configuration settings.

4. Restore Default: Click “Restore Default” button to restore the default settings of the switch.

5. Auto save: Click “Auto save” drop-down menu to choose “Disable” or

“Enable” from the “Auto save” drop-down list to disable or enable Auto save for the switch.

6. Auto save interval (5~65536 sec): Click in “Auto save interval” text box and type a decimal number between 5 and 65536.

7. Submit: Click “Submit” button when you finished Auto save configuration.



Firmware Upgrade

1. Filename: Click in “Filename” text box and type the name of the file that you intend to upgrade it to the switch.

2. TFTP server IP: Click in “TFTP server IP” text box and type the TFTP server IP address from where the file will be obtained.

3. Upgrade: Click “upgrade” button to upgrade firmware to the switch.

Please flow the message on the screen during the firmware upgrade process. Do not turn off the power or perform other functions during this period of time. Reboot the switch after completing the upgrade process.



Please follow the message on the screen during the firmware upgrade process. Do not turn off the power or perform other functions during this period of time.



Firmware has been upgraded successfully to the switch. Reboot the switch



after completing the upgrade process.



Reboot

Reboot: Click “Reboot” button to restart the switch.

Logout

Logout: Click “Logout” button to logout of the switch.



Port

Configuration

1. Admin Setting: Click “Admin Setting” drop-down menu to choose “Link down” or “Link up” from the “Admin Setting” drop-down list to disable or enable Admin Setting for the port.

2. Speed: Click “Speed” drop-down menu to change the line speed and duplex settings from the “Speed” drop-down list for the port.

3. Flow control: Click “Flow control” drop-down menu to choose “Disable” or “Enable” from the “Flow control” drop-down list to disable or enable

Flow control for the port.

4. Submit: Click “Submit” button when you finished configurations.



Port Status

View the Link Status, Speed, Duplex, and Flow control status for all ports.



Rate Control

1. Ingress: Click in “Ingress” text box and type a new Rate to change the

Ingress Rate Control for the port.

Rate Values: 64kbps, 128kbps, 192kbps, … , 1.792mbps; 2mbps,

3mbps, 4mbps, … , 100mbps; 104mbps, 112mbps, 120mbps, … ,

1000mbps.

2. Egress: Click in “Egress” text box and type a new Rate to change the

Egress Rate Control for the port.

Rate Values: 64kbps, 128kbps, 192kbps, … , 1.792mbps; 2mbps,

3mbps, 4mbps, … , 100mbps; 104mbps, 112mbps, 120mbps, … ,

1000mbps.

3. Update setting: Click “Update setting” button when you finished these

Rate Control settings.



RMON Statistics

Click Port 1 ~ Port 14 to view corresponding RMON Statistics.



Per port vlan activities

Click Port 1 ~ Port 14 to view corresponding vlan activities.


Switching


Bridging

1. Aging Time (seconds): Click the text box and type a decimal number as

Bridging Aging Time in seconds.

2. Update setting: Click “update setting” button when you finished Aging

Time settings.

3. Threshold level (0-100): Click in “Level” text box and type a decimal number for the port. Need to choose “Broadcast” and/or

“DFL-Multicast“ from “Storm-control enabled type” for the port. DLF

(Destination Lookup Failure).

4. Storm-control enabled type: Choose “Broadcast” and/or “DLF-Multicast” from “Storm-control enabled type” for the port.

5. Update Setting: Click “Update Setting” button when you finished

Threshold level and Storm-control enabled type settings.



Static MAC Entry

1. Add MAC address: Click in “Add MAC address” text box and type a locked forwarding MAC address for the port.

2. Delete MAC address: Click “Delete MAC address” drop-down menu and choose a locked forwarding MAC address from the “Delete MAC address” drop-down list to be deleted from the port.

3. Submit: Click “Submit” button when you finished Add MAC address and

Delete MAC address settings.

Static-MAC-Entry Discard:

1. Add MAC address: Click in “Add MAC address” text box and type a

MAC address to be discarded for the port.

2. VLAN ID: VLAN ID: Click “VLAN ID” drop-down menu and choose a

VLAN ID from the “VLAN ID” drop-down list.

3. Delete MAC address: Click “Delete MAC address” drop-down menu and choose a MAC address from the “Delete MAC address” drop-down list to be discarded from the port.



4. Submit: Click “Submit” button when you finished Static-MAC-Entry

Discard settings.

Port Mirroring

1. Mirror From: Choose Mirror From port from Port 1 ~ Port 14.

2. Mirror To: Click “Mirror To” drop-down menu to Choose Mirror To port

(Port 1 ~ Port 14) from “Mirror To” drop-down list.

3. Mirror Mode: Click “Mirror Mode” drop-down menu to Choose “Tx/Rx”,

“Tx”, or “Rx” from “Mirror Mode” drop-down list.

4. Submit: Click “Submit” button when you finished Port Mirroring settings.



Trunking

Port Trunking

Static Channel Group:

1. Trunk 1: Click Port 1 ~ Port 12 to assign ports to Trunk 1. (Maximum 4 ports in Trunk 1.)

GE Trunking:

1. Trunk 3: Click “Static” or “Disable” for Trunk 3. (Trunk 3 includes Port 13 and Port 14.)

2. Submit: Click “Submit” button when you finished Port Trunking settings.


STP


Global Configuration

1. Spanning Tree Protocol: Click “Spanning Tree Protocol” drop-down menu to Choose “Enable” or “Disable” from “Spanning Tree Protocol” drop-down list to enable or disable Spanning Tree Protocol.

2. Bridge Priority (0..61440): Click in “Bridge Priority” text box and type a decimal number between 0 and 61440.

3. Hello Time (sec) (1..9): Click in “Hello Time” text box and type a decimal number between 1 and 9.

4. Max Age (sec) (6..28): Click in “Max Age” text box and type a decimal number between 6 and 28.

5. Forward Delay (sec) (4..30): Click in “Forward Delay” text box and type a decimal number between 4 and 30.

6. STP Version: Click “STP Version” drop-down menu to choose “RSTP” or

“STP compatible” from “STP Version” drop-down list.

7. Update setting: Click “Update setting” button when you finished Global

Configuration.



RSTP Port Setting

1. STP Version: Click “STP Version” drop-down menu to choose “RSTP” from “STP Version” drop-down list.

2. Port: Click “Port” drop-down menu to Choose Port 1 ~ Port 14 from

“Port” drop-down list.

3. Priority(Granularity 16): Click in “Priority” text box and enter a value between 0 and 240 to set the priority for the port. A higher priority will designate the port to forward packets first. A lower number denotes a higher priority. This entry must be divisible by 16. The default priority setting is 128.

4. Admin. Path Cost: Click in “Admin. Path Cost” text box and enter a value between 0 and 2000000 to set the Admin. Path Cost for the port. 0 (auto)

- Setting 0 for the Admin. Path Cost will automatically set the speed for forwarding packets to the port for optimal efficiency. Default port cost:

100Mbps port = 200000. Gigabit port = 20000.

5. Point to Point Link: Click “Point to Point Link” drop-down menu to

Choose “Enable” or “Disable” from “Point to Point Link” drop-down list to enable or disable Point to Point Link for the port.

6. Edge Port: Click “Edge Port” drop-down menu to Choose “Enable”,

“Disable”, or “Auto” from “Edge Port” drop-down list to set Enable,

Disable, or Auto Edge Port for the port.

7. Update setting: Click “Update setting” button when you finished RSTP

Port Setting.


VLAN


VLAN Mode Setting

1. VLAN Mode Setting: Click “VLAN Mode Setting” drop-down menu to

Choose “Tag-based VLAN” or “Port-based VLAN” from “VLAN Mode

Setting” drop-down list.

2. Update Setting: Click “Update Setting” button when you finished VLAN

Mode Setting.





802.1Q VLAN Setting

Add VLAN:

1. VLAN setting: Click “VLAN setting”. The “VLAN Setting” window appears.

2. Add VLAN: Click “Add VLAN” button to create a new VLAN from “VLAN

Setting” window.

3. VLAN ID(2-4094): Click in the “VLAN ID” textbox and specify a new

VLAN ID number from 2 ~ 4094.

4. VLAN Name: Click in the “VLAN Name” textbox and type a name for this newly created VLAN.

Add port to or delete port from VLAN:

1. VLAN Member: Choose the port to be added to or deleted from the

VLAN.

2. Tag or Untag: Click “Tag or Untag” drop-down menu to Choose “Tag” or

“Untag” from “Tag or Untag” drop-down list for a “Hybrid” port.

3. Submit: Click “Submit” button when you finished VLAN setting.

Delete VLAN:

1. VLAN setting: Click “VLAN setting”. The “VLAN Setting” window appears.

2. Delete VLAN: Click “Delete VLAN” button.

3. Select a VLAN ID: Click “Select a VLAN ID” drop-down menu from

“Select a VLAN ID” drop-down list to choose the VLAN to be deleted.

4. Submit: Click “Submit” button when you finished VLAN setting.



802.1Q Port Setting

1. VLAN Port Setting: Click “VLAN Port Setting”. The “VLAN Port Setting” window appears.

2. Mode: Click “Mode” drop-down menu to Choose “Access”, “Trunk”, or

“Hybrid” from “Mode” drop-down list for the port. The port will be Tag port if you choose “Trunk” Mode for the port. And the port will be Tag or

Untag port if you choose “Hybrid” Mode for the port.

3. PVID: Click in the “PVID” textbox and specify a new PVID number for the port.

4. Update Setting: Click “Update Setting” button when you finished VLAN

Port Setting.



Port Based VLAN

1. VLAN: Choose the port to be added to or deleted from the VLAN.



2. Select all: Click “select all” button to choose Port 1 ~ Port 14 all to be added to the VLAN.

3. Delete all: Click “delete all” button to choose Port 1 ~ Port 14 all to be deleted from the VLAN.

4. Submit: Click “Submit” button when you finished Port Based VLAN setting.


QoS



1. QoS: Click “QoS” drop-down menu from “QoS” drop-down list to choose

“Enable” or “Disable” to enable or disable QoS.

2. Trust: Enable or disable the switch port to trust the CoS (Class of

Service) labels of all traffic received on that port. Enable or disable a routed port to trust the DSCP (Differentiated Service Code Point) labels of all traffic received on that port.

3. Policy: Choose “Strict Priority(Queue3) + WRR(Queue0-2)” or

“WRR(Queue0-3)”. A strict priority queue is always emptied first. The queues that are used in the WRR (Weighted Round Robin) are emptied in a round−robin fashion, and you can configure the weight for each queue.

4. Weighted Round Robin: Click in the “Weight(1~55)” textbox and specify a new number from 1 ~ 55 for Queue 0 ~ 3.

5. Submit: Click “Submit” button when you finished Global Configuration.



802.1p Priority

1. Priority: Click “Priority” drop-down menu from “Priority” drop-down list to choose 0 ~ 3 for VLAN Priority 0 ~ 7.

2. Submit: Click “Submit” button when you finished 802.1p priority.



DSCP

1. Priority: Click “Priority” drop-down menu from “Priority” drop-down list to choose 0 ~ 3 for DSCP Priority 0 ~ 63.

2. Submit: Click “Submit” button when you finished DSCP.



SNMP

SNMP General Setting

1. SNMP Status: Click “SNMP Status” drop-down menu from “SNMP

Status” drop-down list to choose “Enable” or “Disable” to enable or disable SNMP.

2. Description: Click in the “Description” textbox and specify a new description for SNMP.

3. Location: Click in the “Location” textbox and specify a new location for

SNMP.

4. Contact: Click in the “Contact” textbox and specify a new contact for



SNMP.

5. Trap Community Name: For each “Trap Community Name”, Click in the

“Trap Community Name” textbox and specify a trap community name.

6. Trap Host IP Address: For each “Trap Host IP Address”, Click in the

“Trap Host IP Address” textbox and specify a trap host IP address.

7. Cold Start Trap: Click “Cold Start Trap” drop-down menu from “Cold

Start Trap” drop-down list to choose “Enable” or “Disable” to enable or disable cold start trap.

8. Warm Start Trap: Click “Warm Start Trap” drop-down menu from “Warm

Start Trap” drop-down list to choose “Enable” or “Disable” to enable or disable warm start trap.

9. Link Down Trap: Click “Link Down Trap” drop-down menu from “Link

Down Trap” drop-down list to choose “Enable” or “Disable” to enable or disable link down trap.

10. Link Up Trap: Click “Link Up Trap” drop-down menu from “Link Up Trap” drop-down list to choose “Enable” or “Disable” to enable or disable link up trap.

11. Authentication Failure Trap: Click “Authentication Failure Trap” drop-down menu from “Authentication Failure Trap” drop-down list to choose “Enable” or “Disable” to enable or disable authentication failure trap.

12. Topology Change Trap: Click “Topology Change Trap” drop-down menu from “Topology Change Trap” drop-down list to choose “Enable” or

“Disable” to enable or disable topology change trap.

13. Update Setting: Click “Update Setting” button when you finished SNMP

General Setting.

SNMP v1/v2c

1. Get Community Name: Click in the “Get Community Name” textbox and



specify a get community name.

2. Set Community Name: Click in the “Set Community Name” textbox and specify a set community name.

3. Update Setting: Click “Update Setting” button when you finished SNMP

V1/V2c Setting.



SNM P v3

Add User:

1. Add User: Click “Add User” button. The “SNMP V3 Setting” window

2. appears.

SNMP Version: Click “SNM P Version” drop-down menu from “SNMP

Version” drop-down list to choose “SNMPv3 No-Auth”, “SNMPv3

Auth-MD5”, “SNMPv3 Auth-SHA”, “SNMPv3 Priv Auth-MD5”, or

“S NMPv3 Priv Auth-SHA”. y SNMPv3 No -Auth: Add a user using SNMP v3 without authentication. y SNMPv3 Auth-MD5: Add a user using SNMP v3 with authentication.

Click in the “Auth. Password” textbox and specify an authentication password. y SNMPv3 Auth-SHA: Add a user using SNMP v3 with authentication.

Click in the “Auth. Password” textbox and specify an authentication password. y SNMPv3 Priv Auth-MD5: Add a user using SNMP v3 with authentication and privacy. Click in the “Auth. Password” textbox and specify an authentication password. Click in the “Privacy y

PassPhrase” textbox and specify a privacy pass phrase.

SNMPv3 Priv Auth-SHA: Add a user using SNM P v3 with authentication and privacy. Click in the “Auth. Password” textbox and

3. specify an authentic ation password. Click in the “Privacy

PassPhrase” textbox and specify a privacy pass phrase.

User Name: Click in the “User Name” textbox and specify a u ser name for user using SNMP v3.

4. Access Mode: Click “Access Mode” drop-down menu from “Access

Mo de” drop-d own list to choose “Read Only” or “Read/Write”. y Read Only: Add a user using SNMP v3 with read-only access m ode. y Read/Write: Add an user using SNMP v3 with read-write access mode

5. Sumit: Click “Sumit” button when you finished SNMP V3 Setting.



Delete User:

1. Delete User: Click “Delete User” button. The “Select User Name” window appears.

2. Select User Name: Click “Select User Name” drop-down menu from

“Select User Name” drop-down list to choose the user to be deleted from using SNMP v3.

3. Sumit: Click “Sumit” button when you finished user deletion.



Other Protocols

GVRP

GVRP Global Setting:

1. GVRP: Click “GVRP” drop-down menu from “GVRP” drop-down list to choose “Enable” or “Disable” to enable or disable GVRP (GARP VLAN

Registration Protocol).

2. Dynamic VLAN creation: Click “Dynamic VLAN creation” drop-down menu from “Dynamic VLAN creation” drop-down list to choose “Enable” or “Disable” to enable or disable Dynamic VLAN creation. GARP

(Generic Attribute Registration Protocol) provides IEEE802.1Q compliant VLAN pruning and dynamic VLAN creation on IEEE802.1Q trunk ports.



3. Update Setting: Click “Update Setting” button when you finished GVRP

Global Setting.

Per port setting (include LAG):

1. GVRP: Click “GVRP” drop-down menu from “GVRP” drop-down list to choose “Enable” or “Disable” to enable or disable GVRP for the port.

2. GVRP applicant: Click “GVRP applicant” drop-down menu from “GVRP applicant” drop-down list to choose “Active” or “Normal” to the port.

Ports in the GVRP active applicant state send GVRP VLAN declarations when they are in the STP (Spanning Tree Protocol) blocking state, which prevents the STP bridge protocol data units (BPDUs) from being pruned from the other port. Ports in the GVRP normal applicant state do not declare GVRP VLANs when in the STP blocking state.

3. GVRP registration: Click “GVRP registration” drop-down menu from

“GVRP registration” drop-down list to choose “Enable” or “Disable” to enable or disable GVRP registration to the port. Configuring an

IEEE802.1Q trunk port in registration mode allows dynamic creation (if dynamic VLAN creation is enabled), registration, and deregistration of

VLANs on the trunk port.

4. Update Setting: Click “Update Setting” button when you finished Per port setting.

IGMP Snooping

1. IGMP mode: Click “IGMP mode” drop-down menu from “IGMP mode” drop-down list to choose “Disable”, “Passive”, or “querier” for the switch.

Disable: Disable IGMP on the switch. Passive: The switch with only multicast-data-forwarding capability. Querier: The switch acts as the



querier for the network. There is only one querier on a network at any time.

2. Update Setting: Click “Update Setting” button when you finished IGMP mode settings.

3. VLAN ID: Click “VLAN ID” drop-down menu from “VLAN ID” drop-down list to choose the VLAN under configuration for the switch.

4. IGMP version: Click “IGMP version” drop-down menu from “IGMP version” drop-down list to choose “1”, “2”, or “3” for the switch.

5. Fast-leave: Click “fast-leave” drop-down menu from “fast-leave” drop-down list to choose “Enable” or “Disable” for the switch. Enable this function will allow members of a multicast group to leave the group immediately when an IGMP Leave Report Packet is received by the

Switch.

IGMP querier:

1. Query-interval: Click in the “query-interval” textbox and specify a new number from 1 ~ 18000. The query-interval field is used to set the time

(in seconds) between transmitting IGMP queries. Entries between 1 and

18000 seconds are allowed. Default = 125.

2. Max-response-time: Click in the “max-response-time” textbox and specify a new number from 1 ~ 124. This determines the maximum amount of time in seconds allowed before sending an IGMP response report. The max-response-time field allows an entry between 1 and 124

(seconds). Default = 10.

IGMP passive snooping:

1. Report suppression: Click “report suppression” drop-down menu from

“report suppression” drop-down list to choose “Enable” or “Disable” for the switch. Use this command to enable report suppression for IGMP version 1 and version 2. Report suppression does not apply to IGMP version 3, and is turned off by default for IGMP versionn1 and IGMP version 2 reports. The switch uses IGMP report suppression to forward only one IGMP report per multicast router query to multicast devices.

When IGMP router suppression is enabled, the switch sends the first

IGMP report from all hosts for a group to all the multicast routers. The switch does not send the remaining IGMP reports for the group to the multicast routers. This feature prevents duplicate reports from being sent to the multicast devices.

2. Update Setting: Click “Update Setting” button when you finished IGMP

Snooping.



Command Line Console Management

The switch provides a command line console interface for configuration purposes. The switch can be configured either locally through its RS-232 port or remotely via a Telnet session. For the later, you must specify an IP address for the switch first.

This chapter describes how to configure the switch using its console by Commend Line.

Administration Console

Connect the DB9 null-modem or cross over cable to the RS-232 serial port of the device to the RS-232 serial port of the terminal or computer running the terminal emulation application.

Direct access to the administration console is achieved by directly connecting a terminal or a PC equipped with a terminal-emulation program (such as

HyperTerminal) to the switch console port.

When using the management method, configure the terminal-emulation program to use the following parameters (you can change these settings after login):

[Default parameters]

115,200bps

8 data bits

No parity

1 stop bit



Exec Mode (View Mode)

Logon to Exec Mode (View Mode)

At the switch_a login: prompt just type in “root” and press <Enter> to logon to Exec Mode (or View Mode). switch_a login: root



Basic commands

Exec Mode (or View Mode) is the base mode from where users can perform basic commands like: clear, debug, disable, enable, exit, help, logout, no, quit, show, terminal

The CLI contains a text-based help facility. Access this help by typing in the full or partial command string then typing a question mark “?”. The CLI displays the command keywords or parameters along with a short description.

At the switch_a> prompt just press <?> to list the above basic commands. switch_a>?

At the switch_a> prompt just type in the full or partial command string then typing a question mark “?” to display the command keywords or parameters along with a short description. switch_a>show ?



Login timed out

The login session to Exec Mode (or View Mode) has timed out due to an extended period of inactivity (60 seconds) to indicate authentication attempt timed out. And the switch_a login: prompt will show on the screen.

Logon back to Exec Mode (View Mode)

At the switch_a login: prompt just type in “root” and press <Enter> to logon



back to Exec Mode (or View Mode). switch_a login: root

Exit from Exec Mode (View Mode)

At the switch_a> prompt just type in “exit” and press <Enter> to exit from

Exec Mode (or View Mode). switch_a>exit



Privileged Exec Mode (Enable Mode)

Logon to Privileged Exec Mode (Enable Mode)

At the switch_a> prompt just type in “enable” and press <Enter> to logon to

Privileged Exec Mode (or Enable Mode). And the switch_a# prompt will show on the screen. switch_a>enable

Commands

Privileged Exec Mode (or Enable Mode) allows users to run commands as following.

At the switch_a# prompt just press <?> to list the commands. switch_a#?



At the switch_a# prompt just type in the full or partial command string then typing a question mark “?” to display the command keywords or parameters along with a short description. switch_a#show ?



Login timed out

The login session to Privileged Exec Mode (or Enable Mode) has timed out due to an extended period of inactivity (60 seconds) to indicate authentication attempt timed out. And the switch_a login: prompt will show on the screen.


At the switch_a login: prompt just type in “root” and press <Enter> to logon



back to Exec Mode (or View Mode). switch_a login: root

Exit from Privileged Exec Mode (or Enable Mode)

At the switch_a# prompt just type in “exit” and press <Enter> to exit from

Privileged Exec Mode (or Enable Mode). switch_a#exit



Configure Mode (Configure Terminal Mode)

Logon to Configure Mode (Configure Terminal Mode)

At the switch_a# prompt just type in “configure terminal” and press <Enter> to logon to Configure Mode (or Configure Terminal Mode). And the

switch_a(config)#

prompt will show on the screen. switch_a#configure terminal

Commands

Configure Mode (or Configure Terminal Mode) serves as a gateway into the modes as following.

At the switch_a(config)# prompt just press <?> to list the commands. switch_a(config)#?



At the switch_a(config)# prompt just type in the full or partial command string then typing a question mark “?” to display the command keywords or parameters along with a short description. switch_a(config)#show ?



Login timed out

The login session to Configure Mode (or Configure Terminal Mode) has timed out due to an extended period of inactivity (60 seconds) to indicate authentication attempt timed out. And the switch_a login: prompt will show on the screen.


At the switch_a login: prompt just type in “root” and press <Enter> to logon back to Exec Mode (or View Mode). switch_a login: root



Exit from Configure Mode (or Configure Terminal Mode)

At the switch_a(config)# prompt just type in “exit” and press <Enter> to exit from Configure Mode (or Configure Terminal Mode). switch_a(config)#exit



System

System Information, System Name/Password, IP Address, Save

Configuration, Firmware Upgrade, Reboot, Logout.

System Name/Password

System Name:

1. Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).

The switch_a(config)# prompt will show on the screen. switch_a(config)#

2. Command:

Use hostname command to set or change the network server name.

Use the no hostname command to disable this function.

(no) hostname HOSTNAME

HOSTNAME specifies the network name of the system.

4. Example:

The following example sets the hostname to switch, and shows the change in the prompt: switch_a(config)#hostname switch switch(config)#

Password:




2. Command:

Use enable password command to modify or create a password to be used when entering the Enable mode. enable password PASSWORD

PASSWORD specifies the new password of the system.

4. Example:

The following example sets the new password mypasswd to switch: switch_a(config)#enable password mypasswd switch_a(config)#



IP Address

IP Address/IP Subnet Mask:




2. Command:

Use ip address command to set the IP address of an interface.

Use the no ip address command to remove the IP address from an interface.

Syntax: ip address IP-ADDRESS no ip address IP-ADDRESS no ip address

IP-ADDRESS A.B.C.D/M specifies the IP address and prefix length of an interface.

M specifies IP subnet mask, 8: 255.0.0.0, 16: 255.255.0.0, 24:

255.255.255.0.

4. Example:

The following example sets the new IP address 169.254.1.1 and new IP subnet mask 255.255.0.0 to switch: switch_a(config-if)#ip address 169.254.1.1/16 switch_a(config-if)#

Default Gateway:




2. Command:

Use ip default-gateway command to set the IP address of the default gateway.

Use the no ip default-gateway command to remove the IP address of the default gateway. ip default-gateway IP-ADDRESS no ip default-gateway

IP-ADDRESS A.B.C.D specifies the IP address of the default gateway.

4. Example:

The following example sets the default gateway 169.254.1.254 to switch: switch_a(config)#ip default-gateway 169.254.1.254 switch_a(config)#



Save Configuration

Load config from TFTP server:

1. Command Mode: Privileged Exec mode

Logon to Privileged Exec Mode (Enable Mode).

The switch_a# prompt will show on the screen. switch_a#

2. Command:

Use install image command to load configuration file from tftp server to switch. install image IP-ADDRESS WORD

IP-ADDRESS specifies the IP address of tftp server.

WORD specifies the file name to be loaded to switch.

4. Example:

The following example specifies loading configuration file (file name: WORD) from tftp server (IP address: 169.254.1.2) to switch: switch_a#install image 169.254.1.2 WORD switch_a#

Load config to TFTP server:




2. Command:

Use write config-file command to backup configuration file to tftp server.

Syntax: write config-file IP-ADDRESS


4. Example:

The following example backups configuration file to tftp server (IP address:

169.254.1.2)

: switch_a#write config-file 169.254.1.2 switch_a#

Save Configuration:




2. Command:

Use copy running-config startup-config command to write configurations



to the file to be used at startup. This is the same as the write memory command. copy running-config startup-config

4. Example:

The following example specifies writing configurations to the file to be used at startup to switch: switch_a#copy running-config startup-config switch_a#

Restore Default:




2. Command:

Use restore default command to restore default setting of the switch. restore default

4. Example:

The following example restores default setting of the switch: switch_a#restore default switch_a#

Auto Save:




2. Usage:

Use this command to enable auto save configuration function. The configuration will be automatically saved at every configured interval while this command is enabled. Use the no form of this command to disable this feature. service auto-config enable no service auto-config enable

4. Example:

The following example enables or disables auto save configuration to switch: switch_a(config)#service auto-config enable switch_a(config)#no service auto-config enable



switch_a(config)#

Auto Save Interval (5~65536 sec):




2. Usage:

Use this command to set the interval when the configuration would be automatically saved. The range of interval value is from 5 to 65535. And the default value is 30 seconds. service auto-config interval WORD

WORD specifies the interval value.

4. Example:

The following example sets the interval WORD (10) when the configuration would be automatically saved to switch: switch_a(config)#service auto-config interval 10 switch_a(config)#

Firmware Upgrade




2. Command:

Use install image command to upgrade firmware from tftp server to switch. install image IP-ADDRESS WORD


WORD specifies the file name to be upgraded to switch.

4. Example:

The following example specifies upgrading firmware (file name: WORD) from tftp server (IP address: 169.254.1.2) to switch: switch_a#install image 169.254.1.2 WORD switch_a#

Please follow the message on the screen during the firmware upgrade process. Do not turn off the power or perform other functions during this period of time.



At the “switch_a#” prompt just type in “reload” and press <Enter> to reboot the switch after completing the upgrade process.



Reboot




2. Command:

Use reload command to restart switch. reload

4. Example:

The following example specifies restarting switch: switch_a#reload switch_a login:

Logout

1. Command Mode: Exec mode or Privileged Exec mode

Logon to Exec Mode (View Mode) or Privileged Exec Mode (Enable Mode).

The switch_a> or switch_a# prompt will show on the screen. switch_a> switch_a#

2. Command:

Use logout command to exit from the Exec mode or Privileged Exec mode. logout

4. Example:

The following example specifies to exit from the Exec mode or Privileged

Exec mode. switch_a>logout switch_a login:



Port

Configuration, Port Status, Rate Control, RMON Statistics, Per Port Vlan

Activities.

Configuration

Admin Setting:

1. Command Mode: Interface mode


Then logon to Interface mode. fe1 means port 1.

The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface fe1 switch_a(config-if)#

2. Command:

Use the shutdown command to shut down the selected interface.

Use the no shutdown to disable this function.

(no) shutdown

4. Example:

The following example shows the use of the shutdown command to shut down the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if)#shutdown switch_a(config-if)#

Duplex:





2. Command:

Use duplex command to specify the duplex mode to be used for each interface.

Use the no duplex to disable this function.

Syntax:

(no) duplex MODE

MODE specifies the duplex mode: auto, full, half.



4. Example:

The following example shows the use of duplex MODE (full) to the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if)#duplex full switch_a(config-if)#

Flow control:





2. Command:

Use flowcontrol on command to enable flow control, and configure the flow control mode for the port.

Use the no flowcontrol to disable this function. flowcontrol on no flowcontrol

4. Example:

The following example shows the use of flowcontrol on to the interface fe1

(port 1): switch_a(config)#interface fe1 switch_a(config-if)#flowcontrol on switch_a(config-if)#

Port Status




2. Command:

Use the show interface command to display interface configuration and status. show interface IFNAME

IFNAME specifies the name of the interface for which status and configuration information is desired.



4. Example:

The following example shows the use of show interface to display interface configuration and status of the interface fe1 (port 1): switch_a>show interface fe1

Rate Control





2. Command:

Use this command to specify the ingress/egress rate to be used for each interface. The bandwidth value is in bits.

Use the no parameter with this command to remove the ingress/egress rate to be used for each interface.

(no) rate-control ingress/egress VALUE

VALUE

<1-10000000000 bits> (usable units: k, m, g)

<1-999>k|m for 1 to 999 kilo bits or mega bits.

1g for 1 giga bits.

4. Example:

The following example shows the use of rate-control ingress VALUE (10

mega bits

) to the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if)#rate-control ingress 10m switch_a(config-if)#

RMON Statistics




2. Command:

Use the show interface statistics command to display RMON statistics of interface.

Syntax: show interface statistics IFNAME



IFNAME specifies the name of the interface for which RMON statistics is desired.

4. Example:

The following example shows the use of show interface statistics to display

RMON statistics of the interface fe1 (port 1): switch_a>show interface statistics fe1

Per Port Vlan Activities




2. Command:

Use show vlan command to display information about a particular VLAN by specifying the VLAN ID. show vlan <2-4094>

<2-4094> VLAN ID.

4. Example:

The following is an output of show vlan command displaying information about VLAN 2: switch_a>show vlan 2



Switching

Bridging, Static MAC Entry, Port Mirroring

Bridging

Aging Time (seconds):




2. Command:

Use this command to specify an ageing-out time for a learned MAC address.

The learned MAC address will persist till this specified time.

Bridge GROUP ageing-time AGEINGTIME no bridge GROUP ageing-time

Group = <1-1> The ID of the bridge-group that this ageing time is for.

AGEINGTIME = <10-1000000> The number of seconds of persistence.

4. Example:

The following example sets the new AGEINGTIME (1000) to bridge GROUP

(1): switch_a(config)#bridge 1 ageing-time 1000 switch_a(config)#

Threshold level (0-100):





2. Command:

Use storm-control level command to specify the rising threshold level for broadcasting, multicast, or destination lookup failure traffic. The storm control action occurs when traffic utilization reaches this level. storm-control level LEVEL

LEVEL <0-100> specifies the percentage of the threshold; percentage of the maximum speed (pps) of the interface.



4. Example:

The following example shows setting storm-control level LEVEL (30) to the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if)#storm-control level 30 switch_a(config-if)#

Broadcast:





2. Command:

Use storm-control broadcast enable command to enable broadcast traffic.

Use no storm-control broadcast command to disable broadcast traffic.

Syntax: storm-control broadcast enable no storm-control broadcast

4. Example:

The following example shows setting storm-control broadcast enable to the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if)#storm-control broadcast enable switch_a(config-if)#

Multicast:





2. Command:

Use storm-control multicast enable command to enable multicast traffic.

Use no storm-control multicast command to disable multicast traffic.

Syntax: storm-control multicast enable no storm-control multicast

4. Example:



The following example shows setting storm-control multicast enable to the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if)#storm-control multicast enable switch_a(config-if)#

DLF:





2. Command:

Use storm-control dlf enable command to enable destination lookup failure traffic.

Use no storm-control dlf command to disable destination lookup failure traffic. storm-control dlf enable no storm-control dlf

dlf destination lookup failure

4. Example:

The following example shows setting storm-control dlf enable to the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if)#storm-control dlf enable switch_a(config-if)#

Static MAC Entry

Add MAC address/Delete MAC address:




2. Command:

Use this command to statically configure a bridge entry to forward or discard matching frames.

Syntax: bridge GROUP address MAC forward|discard IFNAME no bridge GROUP address MAC forward|discard IFNAME

GROUP <1-1> Bridge-group ID used for bridging.

MAC the Media Access Control (MAC) address in the HHHH.HHHH.HHHH



format.

IFNAME the interface on which the frame comes in.

4. Example:

The following example configures a bridge GROUP (1) to forward matching frames (MAC address 2222.2222.2222) to the interface fe1 (port 1): switch_a(config)#bridge 1 address 2222.2222.2222 forward fe1 switch_a(config)#

Static-MAC-Entry Discard:




2. Usage:

Use this command to statically configure a bridge entry to discard matching frames.

Syntax: bridge GROUP address MAC discard IFNAME no bridge GROUP address MAC discard IFNAME

GROUP <1-1> Bridge-group ID used for bridging.

MAC the Media Access Control (MAC) address in the HHHH.HHHH.HHHH format.

IFNAME the interface on which the frame comes in.

4. Example:

The following example configures a bridge GROUP (1) to discard matching frames (MAC address 2222.2222.2222) to the interface fe1 (port 1): switch_a(config)#bridge 1 address 2222.2222.2222 discard fe1 switch_a(config)#

Port Mirroring





2. Command:

Use this command to define a mirror source port and its direction.

Use the no parameter with this command to disable port mirroring by the destination port on the specified source port. mirror interface SOURCEPORT direction SNOOPDIRECTION



no mirror interface SOURCEPORT

SOURCEPORT Name of the Source interface to be used.

SNOOPDIRECTION [both|receive|transmit] both Specifies mirroring of traffic in both directions. receive Specifies mirroring of received traffic. transmit Specifies mirroring of transmitted traffic.

4. Example:

The following example enables port mirroring by the destination port fe1 (port

1) on the specified source port fe2 (port 2): switch_a(config)#interface fe1 switch_a(config-if)#mirror interface fe2 direction both switch_a(config-if)#



Trunking

Port Trunking

Port Trunking





2. Usage:

Use static-channel-group command to create a static aggregator, or add a member port to an already-existing static aggregator.

Use the no static-channel-group command to detach the port from the static aggregator. static-channel-group <1-3> no static-channel-group

<1-3> Channel group number.

Maximum 4 ports in static-channel-group 1 and static-channel-group 2.

Maximum 2 ports in static-channel-group 3

4. Example:

The following example adding the interface fe1 (port 1) to

static-channel-group 1

: switch_a(config)#interface fe1 switch_a(config-if)#static-channel-group 1 switch_a(config-if)#



STP

Global Configuration, RSTP Port Setting


STP Version:




2. Command:

Use this command to choose the Spanning Tree protocol or Rapid Spanning

Tree protocol. bridge GROUP protocol PROTOCOL vlan-bridge

GROUP <1-1> Bridge group name used for bridging.

PROTOCOL

ieee IEEE 802.1Q spanning-tree protocol.

rstp IEEE 802.1w rapid spanning-tree protocol.

4. Example:

The following example chooses the PROTOCOL (rstp) on bridge GROUP

(1): switch_a(config)#bridge 1 protocol rstp vlan-bridge switch_a(config)#

Rapid Spanning Tree Protocol:




2. Command:

Use this command to enable the Rapid Spanning Tree protocol on a bridge.

Use the no form of the command to disable the Rapid Spanning Tree protocol on a bridge. bridge GROUP rapid-spanning-tree enable no bridge GROUP rapid-spanning-tree enable BRIDGE-FORWARD


BRIDGE-FORWARD Puts all ports of the specified bridge into the forwarding state.



4. Example:

The following example enables or disables the rapid-spanning-tree on bridge GROUP (1): switch_a(config)#bridge 1 rapid-spanning-tree enable switch_a(config)#no bridge 1 rapid-spanning-tree enable bridge-forward switch_a(config)#

Spanning Tree Protocol:




2. Command:

Use this command to enable the Spanning Tree protocol on a bridge.

Use the no form of the command to disable the Spanning Tree protocol on a bridge. bridge GROUP spanning-tree enable no bridge GROUP spanning-tree enable BRIDGE-FORWARD


BRIDGE-FORWARD Puts all ports of the specified bridge into the forwarding state.

4. Example:

The following example enables or disables the spanning-tree on bridge

GROUP (1): switch_a(config)#bridge 1 spanning-tree enable switch_a(config)#no bridge 1 spanning-tree enable bridge-forward switch_a(config)#

Bridge Priority (0..61440):




2. Command:

Use this command to set bridge priority for the common instance. Using a lower priority indicates a greater likelihood of the bridge becoming root. bridge GROUP priority PRIORITY no bridge GROUP priority

GROUP <1-1> The ID of the bridge group for which the priority is set.

PRIORITY <0-61440> The bridge priority.

4. Example:



The following example sets the priority PRIORITY (4096) of bridge GROUP

(1): switch_a(config)#bridge 1 priority 4096 switch_a(config)#

Hello Time (sec) (1..9):




2. Command:

Use this command to set the hello-time, the time in seconds after which (if this bridge is the root bridge) all the bridges in a bridged LAN exchange

Bridge Protocol Data Units (BPDUs). bridge GROUP hello-time HELLOTIME no bridge GROUP hello-time

GROUP <1-1> The ID of the bridge group to which this hello time is assigned.

HELLOTIME <1-9> The hello BPDU interval in seconds.

4. Example:

The following example sets the hello-time HELLOTIME (9) of bridge GROUP

(1): switch_a(config)#bridge 1 hello-time 9 switch_a(config)#

Max Age (sec) (6..28):




2. Command:

Use this command to set the max-age for a bridge.

Use the no parameter with this command to restore the default value of max-age.

Syntax: bridge GROUP max-age MAXAGE no bridge GROUP max-age

GROUP <1-1> The ID of the bridge group to which this maximum age time is assigned.

MAXAGE <6-28> The maximum time, in seconds, to listen for the root bridge.

4. Example:



The following example sets the max-age MAXAGE (28) of bridge GROUP

(1): switch_a(config)#bridge 1 max-age 28 switch_a(config)#

Forward Delay (sec) (4..30):




2. Command:

Use this command to set the time (in seconds) after which (if this bridge is the root bridge) each port changes states to learning and forwarding.

Use the no parameter with this command to restore the default value. bridge GROUP forward-time FORWARD_DELAY no bridge GROUP forward-time

GROUP <1-1> The ID of the bridge group to which this delay time is assigned.

FORWARD_DELAY <4-30> the forwarding time delay in seconds.

4. Example:

The following example sets the forward-time FORWARD_DELAY (30) of bridge GROUP (1): switch_a(config)#bridge 1 forward-time 30 switch_a(config)#

RSTP Port Setting

Priority(Granularity 16):





2. Command:

Use this command to set the port priority for a bridge. The lower priority indicates a greater likelihood of the bridge becoming root. bridge GROUP priority PRIORITY

GROUP <1-1> the ID of the bridge group.

PRIORITY <0-240> The priority to be assigned to the group.

4. Example:



The following example sets the priority PRIORITY (100) of the interface fe1

(port 1) of bridge GROUP (1): switch_a(config)#interface fe1 switch_a(config-if)#bridge 1 priority 100 switch_a(config-if)#

Admin. Path Cost:





2. Command:

Use this command to set the cost of a path associated with a bridge-group.

Use the no parameter with this command to restore the default cost of a path associated with a bridge-group.

Syntax: bridge GROUP path-cost PATHCOST no bridge GROUP path-cost

GROUP <1-1> the ID of the bridge group.

PATHCOST <1-200000000> The cost to be assigned to the group.

4. Example:

The following example sets the cost (123) of the interface fe1 (port 1) of bridge GROUP (1): switch_a(config)#interface fe1 switch_a(config-if)#bridge 1 path-cost 123 switch_a(config-if)#

Point to Point Link:





2. Command:

Use spanning-tree link-type command to set the link type of a port to enable or disable rapid transition.

Use the no spanning-tree link-type command to set a port to its default state and to disable rapid transition.



(no) spanning-tree link-type LINKTYPE

LINKTYPE The link type to be assigned to the port.

point-to-point Enable rapid transition.

shared Disable rapid transition.

4. Example:

The following example sets the link-type LINKTYPE (point-to-point) of the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if)#spanning-tree link-type point-to-point switch_a(config-if)#

Autoedge:





2. Command:

Use spanning-tree autoedge command to assist in automatic identification of the edge port.

Use the no spanning-tree autoedge command to disable this feature.

(no) spanning-tree autoedge

4. Example:

The following example enables the spanning-tree autoedge of the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if)#spanning-tree autoedge switch_a(config-if)#

Edgeport:





2. Command:

Use spanning-tree edgeport command to set a port as an edge-port and to enable rapid transitions.

Use the no spanning-tree edgeport command to set a port to its default



state (not an edge-port) and to disable rapid transitions.

(no) spanning-tree edgeport

4. Example:

The following example enables the spanning-tree edgeport of the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if)#spanning-tree edgeport switch_a(config-if)#



VLAN

VLAN Mode Setting, 802.1Q VLAN Setting, 802.1Q Port Setting, Port Based

VLAN

802.1Q VLAN Setting

VLAN Database:




2. Usage:

Use vlan database command to enter the VLAN configuration mode. vlan database

4. Example:

The following example changes to VLAN configuration mode from Configure mode: switch_a(config)#vlan database switch_a(config-vlan)#

Add VLAN/Delete VLAN:

1. Command Mode: VLAN Configure mode


Logon to VLAN Configure Mode.

The switch_a(config-vlan)# prompt will show on the screen. switch_a(config)#vlan database switch_a(config-vlan)#

2. Usage:

This command enables or disables the state of a particular VLAN on a bridge basis. Specifying the disable state causes all forwarding over the specified

VLAN ID on the specified bridge to cease. Specifying the enable state allows forwarding of frames on the specified VLAN-aware bridge.

Syntax: vlan VLANID bridge GROUP name VLAN_NAME state enable/disable no vlan VLANID bridge GROUP

VLANID The VID of the VLAN that will be enabled or disabled on the bridge

<2-4094>.

GROUP <1-1> The ID of the bridge-group on which the VLAN will be affected.

VLAN_NAME The ASCII name of the VLAN. Maximum length: 16



characters. enable Sets VLAN into an enable state. disable Sets VLAN into a disable state.

4. Example:

The following example enables the vlan VLANID (2) and name VLAN_NAME

(vlan2) of bridge GROUP (1): switch_a(config-vlan)#vlan 2 bridge 1 name vlan2 state enable switch_a(config-vlan)#

802.1Q Port Setting

Switchport mode access:





2. Usage:

Use switchport mode access command to set the switching characteristics of the Layer-2 interface to access mode, and classify untagged frames only.

Use the no switchport access command to reset the mode of the Layer-2 interface to access (default). switchport mode access no switchport access

4. Example:

The following example sets the switchport mode access of the interface fe1

(port 1): switch_a(config)#interface fe1 switch_a(config-if)#switchport mode access switch_a(config-if)#

Switchport mode hybrid:





2. Usage:

Use switchport mode hybrid command to set the switching characteristics of the Layer-2 interface as hybrid, and classify both tagged and untagged



frames.

Use the no switchport hybrid command to reset the mode of the Layer-2 interface to access (default).

Syntax: switchport mode hybrid switchport mode hybrid acceptable-frame-type all/vlan-tagged no switchport hybrid

all Set all frames can be received.

vlan-tagged Set vlan-tagged frames can only be received.

4. Example:

The following example sets the switchport mode hybrid of the interface fe1

(port 1) and all frames to be received on interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if)#switchport mode hybrid acceptable-frame-type all switch_a(config-if)#

Switchport mode trunk:





2. Usage:

Use switchport mode trunk command to set the switching characteristics of the Layer-2 interface as trunk, and specify only tagged frames.

Use the no switchport trunk command to reset the mode of the Layer-2 interface to access (default). switchport mode trunk no switchport trunk

4. Example:

The following example sets the switchport mode trunk of the interface fe1

(port 1): switch_a(config)#interface fe1 switch_a(config-if)#switchport mode trunk switch_a(config-if)#

Switchport hybrid allowed vlan:







2. Usage:

Use this command to set the switching characteristics of the Layer-2 interface to hybrid. Both tagged and untagged frames will be classified over hybrid interfaces.

Use the no parameter to turn off allowed hybrid switching. switchport hybrid allowed vlan all switchport hybrid allowed vlan none switchport hybrid allowed vlan add VLANID egress-tagged enable/disable switchport hybrid allowed vlan remove VLANID no switchport hybrid vlan all Allow all VLANs to transmit and receive through the Layer-2 interface. none Allow no VLANs to transmit and receive through the Layer-2 interface. add Add a VLAN to the member set. remove Remove a VLAN from the member set.

VLANID <2-4094> The ID of the VLAN or VLANs that will be added to, or removed from, the Layer-2 interface.

For a VLAN range, specify two VLAN numbers: lowest, then highest number in the range, separated by a hyphen.

For a VLAN list, specify the VLAN numbers separated by commas. egress-tagged enable Enable the egress tagging for the outgoing frames. disable Disable the egress tagging for the outgoing frames.

4. Example:

The following example specifies to add the interface fe1 (port 1) to VLANID

(2) and enable the egress-tagged for the outgoing frames on interface fe1

(port 1): switch_a(config)#interface fe1 switch_a(config-if)#switchport hybrid allowed vlan add 2 egress-tagged enable switch_a(config-if)#

Switchport trunk allowed vlan:





2. Usage:

Use this command to set the switching characteristics of the Layer-2 interface to trunk. The all parameter indicates that any VLAN ID is part of its port’s member set. The none parameter indicates that no VLAN ID is configured on



this port. The add and remove parameters will add and remove VLAN IDs to/from the port’s member set.

Use the no parameter to remove all VLAN IDs configured on this port.

Syntax: switchport trunk allowed vlan all switchport trunk allowed vlan none switchport trunk allowed vlan add VLANID switchport trunk allowed vlan remove VLANID switchport trunk allowed vlan except VLANID no switchport trunk vlan all Allow all VLANs to transmit and receive through the Layer-2 interface. none Allow no VLANs to transmit and receive through the Layer-2 interface. add Add a VLAN to transmit and receive through the Layer-2 interface. remove Remove a VLAN from transmit and receive through the Layer-2 interface. except All VLANs, except the VLAN for which the ID is specified, are part of its ports member set.

VLANID <2-4094> The ID of the VLAN or VLANs that will be added to, or removed from, the Layer-2 interface. A single VLAN, VLAN range, or VLAN list can be set.

For a VLAN range, specify two VLAN numbers: lowest, then highest number in the range, separated by a hyphen.

For a VLAN list, specify the VLAN numbers separated by commas.

4. Example:


(2): switch_a(config)#interface fe1 switch_a(config-if)#switchport trunk allowed vlan add 2 switch_a(config-if)#

Port Based VLAN

Switchport portbase add/remove vlan:





2. Usage:

Use this command to set or remove the default VLAN for the interface.

Syntax: switchport portbase add｜remove vlan VLANID

VLANID The ID of the VLAN will be added to or removed from the Layer-2 interface.



4. Example:


(2): switch_a(config)#interface fe1 switch_a(config-if)#switchport portbase add vlan 2 switch_a(config-if)#



QoS

Global Configuration, 802.1p Priority, DSCP


QoS:




2. Command:

Use mls qos enable command to globally enable QoS.

Use the no mls qos command to globally disable QoS. mls qos enable

(no) mls qos

4. Example:

The following example globally enables QoS on the switch: switch_a(config)#mls qos enable switch_a(config)#

Trust:




2. Command:

Use mls qos trust command to turn on QoS trust CoS or DSCP.

Use the no mls qos trust command to turn off QoS trust CoS or DSCP.

(no) mls qos trust cos/dscp

cos Class of Service.

dscp Differentiated Service Code Point.

4. Example:

The following example turns on QoS trust CoS on the switch: switch_a(config)#mls qos trust cos switch_a(config)#

Strict Priority:






2. Command:

Use priority-queue out command to enable the egress expedite queue.

Use the no priority-queue out command to disable the egress expedite queue.

(no) priority-queue out

4. Example:

The following example enables the egress expedite queue on the switch: switch_a(config)#priority-queue out switch_a(config)#

Weighted Round Robin:




2. Command:

Use wrr-queue bandwidth command to specify the bandwidth ratios of the transmit queues.

Syntax: wrr-queue bandwidth WRR_WTS

WRR_WTS Weighted Round Robin (WRR) weights for the 4 queues (4 values separated by spaces). Range is 1-55.

4. Example:

The following example specifies the bandwidth ratios of the transmit queues on the switch: switch_a(config)#wrr-queue bandwidth 1 2 4 8 switch_a(config)#

802.1p Priority




2. Command:

Use wrr-queue cos-map command to specify CoS values for a queue.

Syntax: wrr-queue cos-map QUEUE_ID COS_VALUE



QUEUE_ID Queue ID. Range is 0-3.

COS_VALUE CoS values. Up to 8 values (separated by spaces). Range is

0-7.

4. Example:

The following example shows mapping CoS values 0 and 1 to queue 1 on the switch: switch_a(config)#wrr-queue cos-map 1 0 1 switch_a(config)#

DSCP




2. Command:

Use mls qos map dscp-queue command to map the DSCP values to a queue.

Syntax: mls qos map dscp-queue DSCP_VALUE to QUEUE_ID

DSCP_VALUE DSCP values. Up to 8 values (separated by spaces). Range is 0-63.

QUEUE_ID Queue ID. Range is 0-3.

4. Example:

The following example shows mapping DSCP values 0 to 3 to queue 1 on the switch: switch_a(config)#mls qos map dscp-queue 0 1 2 3 to 1 switch_a(config)#



SNMP

SNMP General Setting, SNMP v1/v2c, SNMP v3

SNMP General Setting

SNMP Status:




2. Command:

Use snmp-server enable command to enable and no snmp-server enable command to disable SNMP to the switch.

(no) snmp-server enable

4. Example:

The following example enables SNMP to the switch: switch_a(config)#snmp-server enable switch_a(config)#

Description:




2. Command:

Use snmp-server description command to specify and no snmp-server

description

command to remove description for SNMP. snmp-server description DESCRIPTION no snmp-server description

DESCRIPTION The description for SNMP.

4. Example:

The following example specifies description (description) for SNMP: switch_a(config)#snmp-server description description switch_a(config)#

Location:






2. Command:

Use snmp-server location command to specify and no snmp-server

location

command to remove location for SNMP.

Syntax: snmp-server location LOCATION no snmp-server location

LOCATION The location for SNMP.

4. Example:

The following example specifies location (location) for SNMP: switch_a(config)#snmp-server location location switch_a(config)#

Contact:




2. Command:

Use snmp-server contact command to specify and no snmp-server

contact

command to remove contact for SNMP. snmp-server contact CONTACT no snmp-server contact

CONTACT The contact for SNMP.

4. Example:

The following example specifies contact (contact) for SNMP: switch_a(config)#snmp-server contact contact switch_a(config)#

Trap Community Name:




2. Command:

Use this command to specify trap community name for SNMP.

Use the no parameter with this command to remove trap community name for

SNMP.



snmp-server trap-community <1-5> NAME no snmp-server trap-community <1-5>

<1-5> The trap community 1-5.

NAME The trap community name for SNMP.

4. Example:

The following example specifies trap community name 1 (name) for SNMP: switch_a(config)#snmp-server trap-community 1 name switch_a(config)#

Trap Host IP Address:




2. Command:

Use this command to specify trap host IP address for SNMP.

Use the no parameter with this command to remove trap host IP address for

SNMP. snmp-server trap-ipaddress <1-5> IP-ADDRESS no snmp-server trap-ipaddress <1-5>

<1-5> The trap host IP address 1-5.

IP-ADDRESS The trap host IP address for SNMP. A.B.C.D specifies the IP address.

4. Example:

The following example specifies trap host 1 IP address (169.254.1.2) for

SNMP: switch_a(config)#snmp-server trap-ipaddress 169.254.1.2 switch_a(config)#

Cold Start Trap:




2. Command:

Use snmp-server trap-type enable coldStart command to enable cold start trap for SNMP.

Use the no snmp-server trap-type enable coldStart command to disable cold start trap for SNMP.

(no) snmp-server trap-type enable coldStart



4. Example:

The following example enables cold start trap for SNMP: switch_a(config)#snmp-server trap-type enable coldStart switch_a(config)#

Warm Start Trap:




2. Command:

Use snmp-server trap-type enable warmStart command to enable warm start trap for SNMP.

Use the no snmp-server trap-type enable warmStart command to disable warm start trap for SNMP.

(no) snmp-server trap-type enable warmStart

4. Example:

The following example enables warm start trap for SNMP: switch_a(config)#snmp-server trap-type enable warmStart switch_a(config)#

Link Down Trap:




2. Command:

Use snmp-server trap-type enable linkDown command to enable link down trap for SNMP.

Use the no snmp-server trap-type enable linkDown command to disable link down trap for SNMP.

Syntax:

(no) snmp-server trap-type enable linkDown

4. Example:

The following example enables link down trap for SNMP: switch_a(config)#snmp-server trap-type enable linkDown switch_a(config)#

Link Up Trap:



The switch_a(config)# prompt will show on the screen.



switch_a(config)#

2. Command:

Use snmp-server trap-type enable linkUp command to enable link up trap for SNMP.

Use the no snmp-server trap-type enable linkUp command to disable link up trap for SNMP.

(no) snmp-server trap-type enable linkUp

4. Example:

The following example enables link up trap for SNMP: switch_a(config)#snmp-server trap-type enable linkUp switch_a(config)#

Authentication Failure Trap:




2. Command:

Use snmp-server trap-type enable authenticationFailure command to enable authentication failure trap for SNMP.

Use the no snmp-server trap-type enable authenticationFailure command to disable authentication failure trap for SNMP.

(no) snmp-server trap-type enable authenticationFailure

4. Example:

The following example enables authentication failure trap for SNMP: switch_a(config)#snmp-server trap-type enable authenticationFailure switch_a(config)#

Topology Change Trap:




2. Command:

Use snmp-server trap-type enable topologyChange command to enable topology change trap for SNMP.

Use the no snmp-server trap-type enable topologyChange command to disable topology change trap for SNMP.



(no) snmp-server trap-type enable topologyChange

4. Example:

The following example enables topology change trap for SNMP: switch_a(config)#snmp-server trap-type enable topologyChange switch_a(config)#

SNMP v1/v2c

Get Community Name:




2. Command:

Use snmp-server community get command to specify and no

snmp-server community get

command to remove get community name for

SNMP.

Syntax: snmp-server community get NAME no snmp-server community get

NAME The get community name for SNMP.

4. Example:

The following example specifies get community name (name) for SNMP: switch_a(config)#snmp-server community get name switch_a(config)#

Set Community Name:




2. Command:

Use snmp-server community set command to specify and no

snmp-server community set

command to remove get community name for

SNMP. snmp-server community set NAME no snmp-server community set

NAME The set community name for SNMP.

4. Example:

The following example specifies set community name (name) for SNMP: switch_a(config)#snmp-server community set name switch_a(config)#



SNMP v3

SNMPv3 No-Auth:




2. Command:

Add a user using snmp v3 with read-only or read-write access mode and without authentication. Use the no form of the command to delete this user.

(no) snmp-server v3-user USERNAME (ro｜rw) noauth

USERNAME Specify a user name. ro read-only access mode rw read-write access mode

4. Example:

The following example adds a user (myuser) using snmp v3 with read-only access mode and without authentication: switch_a(config)#snmp-server v3-user myuser ro noauth switch_a(config)#

SNMPv3 Auth-MD5, SNMPv3 Auth-SHA:




2. Command:

Add a user using snmp v3 with read-only or read-write access mode and with

MD5 or SHA authentication. Use the no form of the command to delete this user.

(no) snmp-server v3-user USERNAME (ro ｜ rw) auth (md5 ｜ sha)

AUTH_PASSWORD

USERNAME Specify a user name. ro read-only access mode rw read-write access mode md5 authentication method sha authentication method

AUTH_PASSWORD authentication password

4. Example:

The following example adds a user (myuser) using snmp v3 with read-write access mode and MD5 authentication (mypassword): switch_a(config)#snmp-server v3-user myuser rw auth md5 mypassword



switch_a(config)#

SNMPv3 Priv Auth-MD5, SNMPv3 Priv Auth-SHA:




2. Command:

Add a user using snmp v3 with read-only or read-write access mode, MD5 or

SHA authentication, and privacy. Use the no form of the command to delete this user.

(no) snmp-server v3-user USERNAME (ro ｜ rw) priv auth (md5 ｜ sha)

AUTH_PASSWORD des PRIV_PASS_PHRASE

USERNAME Specify a user name. ro read-only access mode rw read-write access mode md5 authentication method sha authentication method

AUTH_PASSWORD authentication password

PRIV_PASS_PHRASE encryption pass phrase

4. Example:

The following example adds a user (myuser) using snmp v3 with read-write access mode, MD5 authentication (mypassword), and encryption pass phrase (mypassphrase): switch_a(config)#snmp-server v3-user myuser rw priv md5 mypassword des mypassphrase switch_a(config)#



Other Protocols

GVRP, IGMP Snooping

GVRP

GVRP:




2. Command:

Use set gvrp enable bridge command to enable (set) and set gvrp disable

bridge

command to disable (reset) GVRP globally for the bridge instance.

This command does not enable/disable GVRP in all ports of the bridge. After enabling GVRP globally, use the set port gvrp enable command to enable

GVRP on individual ports of the bridge.

Syntax: set gvrp enable bridge GROUP set gvrp disable bridge GROUP

GROUP Bridge-group ID used for bridging.

4. Example:

The following example globally enables GVRP to bridge GROUP (1): switch_a(config)#set gvrp enable bridge 1 switch_a(config)#

Dynamic VLAN creation:




2. Command:

Use set gvrp dynamic-vlan-creation enable bridge command to enable and set gvrp dynamic-vlan-creation disable bridge command to disable dynamic VLAN creation for a specific bridge instance. set gvrp dynamic-vlan-creation enable bridge GROUP set gvrp dynamic-vlan-creation disable bridge GROUP

GROUP Bridge-group ID used for bridging.

4. Example:

The following example enables dynamic VLAN creation for bridge GROUP



(1): switch_a(config)#set gvrp dynamic-vlan-creation enable bridge 1 switch_a(config)#

Per port setting:

GVRP:




2. Command:

Use set port gvrp enable command to enable and set port gvrp disable command to disable GVRP on a port or all ports in a bridge.

Syntax: set port gvrp enable all/IFNAME set port gvrp disable all/IFNAME all All ports added to recently configured bridge.

IFNAME The name of the interface.

4. Example:

The following example enables GVRP on the interface fe1 (port 1): switch_a(config)#set port gvrp enable fe1 switch_a(config)#

Per port setting:

GVRP applicant:




2. Command:

Use this command to set the GVRP applicant state to normal or active. set gvrp applicant state active/normal IFNAME active Active state normal Normal state

IFNAME Name of the interface.

4. Example:

The following example sets GVRP applicant state to active on the interface fe1 (port 1): switch_a(config)#set gvrp applicant state active fe1 switch_a(config)#

Per port setting:



GVRP registration:




2. Command:

Use this command to set GVRP registration to normal, fixed, and forbidden registration mode for a given port. set gvrp registration normal IF_NAME set gvrp registration fixed IF_NAME set gvrp registration forbidden IF_NAME normal Specify dynamic GVRP multicast registration and deregistration on the port. fixed Specify the multicast groups currently registered on the switch are applied to the port, but any subsequent registrations or deregistrations do not affect the port. Any registered multicast groups on the port are not deregistered based on the GARP timers. forbidden Specify that all GVRP multicasts are deregistered, and prevent any further GVRP multicast registration on the port.

IF_NAME The name of the interface.

4. Example:

The following example sets GVRP registration to fixed registration mode on the interface fe1 (port 1): switch_a(config)#set gvrp registration fixed fe1 switch_a(config)#

IGMP Snooping

IGMP mode:

Querier:



Then logon to Interface mode. vlan1.1 means vlan 1.

The switch_a(config-if)# prompt will show on the screen. switch_a(config)#interface vlan1.1 switch_a(config-if)#

2. Command:

Use ip igmp snooping querier command to enable IGMP querier operation on a subnet (VLAN) when no multicast routing protocol is configured in the subnet (VLAN). When enabled, the IGMP Snooping querier sends out periodic IGMP queries for all interfaces on that VLAN.

Use the no ip igmp snooping querier command to disable IGMP querier configuration.



(no) ip igmp snooping querier

4. Example:

The following example enables IGMP snooping querier on vlan1.1: switch_a(config)#interface vlan1.1 switch_a(config-if)#ip igmp snooping querier

IGMP mode:

Passive:

1. Command Mode: Configure mode or Interface mode


The switch_a(config)# prompt will show on the screen.


The switch_a(config-if)# prompt will show on the screen. switch_a#configure terminal switch_a(config)# switch_a(config)#interface vlan1.1 switch_a(config-if)#

2. Command:

Use ip igmp snooping command to enable IGMP Snooping. When this command is given in the Global Config mode, IGMP Snooping is enabled at the switch level. When this command is given at the VLAN interface level,

IGMP Snooping is enabled for that VLAN.

Use the no ip igmp snooping command to globally disable IGMP Snooping, or for the specified interface.

(no) ip igmp snooping

4. Example:

The following example enables IGMP snooping on the switch or vlan1.1: switch_a#configure terminal switch_a(config)# ip igmp snooping switch_a(config)#interface vlan1.1 switch_a(config-if)#ip igmp snooping

IGMP version:







2. Command:

Use ip igmp version command to set the current IGMP protocol version on an interface.

To return to the default version, use the no ip igmp version command.

Syntax: ip igmp version VERSION no ip igmp version

VERSION IGMP protocol version number.

4. Example:

The following example sets the IGMP protocol version 3 on the interface fe1

(port 1): switch_a(config)#interface fe1 switch_a(config-if)#ip igmp version 3

Fast-leave:





2. Command:

Use ip igmp snooping fast-leave command to enable IGMP Snooping fast-leave processing. Fast-leave processing is analogous to immediate leave processing; the IGMP group-membership is removed, as soon as an

IGMP leave group message is received without sending out a group-specific query.

Use the no ip igmp snooping fast-leave command to disable fast-leave processing.

Syntax:

(no) ip igmp snooping fast-leave

4. Example:

The following example enables IGMP snooping fast-leave on vlan1.1: switch_a(config)#interface vlan1.1 switch_a(config-if)#ip igmp snooping fast-leave

IGMP querier:

Query-interval:




The switch_a(config-if)# prompt will show on the screen.



switch_a(config)#interface fe1 switch_a(config-if)#

2. Command:

Use ip igmp query-interval command to configure the frequency of sending

IGMP host query messages.

To return to the default frequency, use the no ip igmp query-interval command. ip igmp query-interval INTERVAL no ip igmp query-interval

INTERVAL <1-18000> Frequency (in seconds) at which IGMP host query messages are sent.

4. Example:

The following example changes the frequency of sending IGMP host-query messages to 2 minutes on the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if)#ip igmp query-interval 120

IGMP querier:

Max-response-time:





2. Command:

Use ip igmp query-max-response-time command to configure the frequency of sending IGMP host query messages.

To return to the default frequency, use the no ip igmp

query-max-response-time

command.

Syntax: ip igmp query-max-response-time RESPONSETIME no ip igmp query-max-response-time

RESPONSETIME <1-240> Maximum response time (in seconds) advertised in IGMP queries.

4. Example:

The following example configures a maximum response time of 8 seconds on the interface fe1 (port 1): switch_a(config)#interface fe1 switch_a(config-if)#ip igmp query-max-response-time 8




Static mc router port:





2. Command:

Use ip igmp snooping mrouter interface command to statically configure the specified VLAN constituent interface as a multicast router interface for

IGMP Snooping in that VLAN.

Use the no ip igmp snooping mrouter interface command to remove the static configuration of the interface as a multicast router interface.

Syntax:

(no) ip igmp snooping mrouter interface IFNAME

IFNAME Specify the name of the interface

4. Example:

The following example shows interface fe1 (port 1) statically configured to be a multicast router interface on vlan1.1: switch_a(config)#interface vlan1.1 switch_a(config-if)#ip igmp snooping mrouter interface fe1


Report suppression:





2. Command:

Use ip igmp snooping report-suppression command to enable report suppression for IGMP versions 1 and 2.

Use the no ip igmp snooping report-suppression command to disable report suppression.

(no) ip igmp snooping report-suppression

4. Example:

The following example enables report suppression for IGMPv2 reports on

vlan1.1

:



switch_a(config)#interface vlan1.1 switch_a(config-if)#ip igmp version 2 switch_a(config-if)#ip igmp snooping report-suppression



Specifications

Applicable Standards

Switching Method

Forwarding Rate

10BaseT

100BaseTX

1000BaseT

1000BaseSX

Performance

Cable

10BaseT

100BaseTX

1000BaseT

1000BaseSX

LED Indicators

Dimensions

Net Weight

Power Input

Power Consumption

Operating

Temperature

Storage Temperature

Humidity

Safety

EMI

EMS

IEEE 802.3 10BaseT

IEEE 802.3u 100BaseTX

IEEE 802.3ab 1000BaseT

IEEE 802.3z 1000BaseSX

Store-and-Forward

10 / 20Mbps half / full-duplex

100 / 200Mbps half / full-duplex

2000Mbps full-duplex

2000Mbps full-duplex

14,880pps for 10Mbps

148,810pps for 100Mbps

1,488,100pps for 1000Mbps

2-pair UTP/STP Cat. 3, 4, 5

Up to 100m (328ft)

2-pair UTP/STP Cat. 5

Up to 100m (328ft)

4-pair UTP/STP Cat. 5

Up to 100m (328ft)

50 or 62.5/125µm multi-mode fiber (850nm) up to 550m

Per unit – Power status (Power 1, 2, 3)

Per port – Link/ACT and 10/100 or 1000 Mbps

235mm (W) * 125mm(D) * 50mm( H)

1.5kg approx.

Terminal Block: 24VDC

15W max.

-40°C to 75℃ (-40℉ to 167℉)

Tested for functional operation @

-40℃ to 85℃ (-40℉ to 185℉)

-40°C to 85℃ (-40℉ to 185℉)

5%-95% non-condensing

UL508, EN60950-1, IEC60950-1

FCC Part 15, Class B

EN61000-6-3: EN55022, EN61000-3-2, EN61000-3-3

EN61000-4-2 (ESD Standard)

EN61000-4-3 (Radiated RFI Standards)

EN61000-4-4 (Burst Standards)

EN61000-4-5 (Surge Standards)

EN61000-4-6 (Induced RFI Standards)

EN61000-4-8 (Magnetic Field Standards)

EN61000-4-11 (Voltage Dips Standards)



Environmental Test

Compliance

IEC60068-2-6 Fc (Vibration Resistance)

IEC60068-2-27 Ea (Shock)

IEC60068-2-32 Ed (Free Fall)

NEMA TS1/2 Environmental requirements for traffic control equipment



Appendix

B9 DCE pin assignment

Pin no. Name

1 DCD

2 RxD

3 TxD

4 ---

5 GND

6 DSR

7 ---

8 CTS

9 ---

RS232 Signal name

Data Carrier detect

N/C

Data set Ready

N/C

Clear to send

N/C


72129A ZYYT | Motorola 72128A XT, 72129A XT, ZYYT Ethernet Switch User's Manual 126 Pages

72129A ZYYT | Motorola 72128A XT, 72129A XT, ZYYT Ethernet Switch User's Manual

Preface

Table of Contents

REFACE

ABLE OF

ONTENTS

RODUCT

VERVIEW

NSTALLATION

WITCH

ANAGEMENT

EB

ASED

ROWSER

ANAGEMENT

ANAGEMENT

EB

ASED

ROWSER

ANAGEMENT

OMMAND

INE

ONSOLE

ANAGEMENT

PECIFICATIONS

PPENDIX

Product Overview

Managed Ethernet Switch

Package Contents

Product Highlights

Basic Features

Management Support

Front Panel Display

Physical Ports

Switch Management

Web-based browser interface

Administration console via RS-232 serial port (CLI)

External SNMP-based network management application

Installation

Selecting a Site for the Switch

Connecting to Power

DC Terminal Block power input

Connecting to Your Network

Cable Type & Length

Speed Connector Port

Speed

Half/Full

Duplex

Cable Max.

Distance

Cabling

Switch Management

Management Access Overview

Administration Console (CLI)

Direct Access

♦ 115,200bps

♦ 8 data bits

♦ No parity

♦ 1 stop bit

Modem Access

Web Management

SNMP-Based Network Management

strings for the switch are public.

Protocols

Management Architecture

SNMP & RMON Management

Overview

SNMP Agent and MIB-2 (RFC 1213)

RMON MIB (RFC 1757) and Bridge MIB (RFC

1493)

RMON Groups Supported

Bridge Groups Supported

Web-Based Browser Management

Logging on to the switch

Understanding the Browser Interface

System

Port

Switching

Trunking