IEI Integration POC-17C-ULT3 17” Medical Grade Panel PC User Manual

POC-17C-ULT3 Medical Panel PC

MODEL:

POC-17C-ULT3

17” Medical Panel PC with Intel® Core™ i7-6600U/Core™ i5-6300U/

Celeron® 3855U CPU, 4 GB DDR4 RAM, Wi-Fi 802.11a/b/g/n/ac,

PCAP Touchscreen, 2-Megapixel Camera and Microphone

Rev. 1.03 - November 28, 2017

Page i


Revision

November 28, 2017 1.03

October 18, 2017 1.02

September 29, 2017 1.01

August 9, 2017 1.00

Added the 150W/19V power adapter as the power supply option

Modified environment and power adapter information

Added a note on Page 66

Initial release

Page ii


Copyright

COPYRIGHT NOTICE

The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

TRADEMARKS

All registered trademarks and product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective owners.

CONTACT INFORMATION

IEI Integration Corp.

Address: No. 29, Zongxing Rd., Xizhi Dist.,

Phone:

New Taipei City 221, Taiwan

+886-2-8691-6798

Fax:

Web Site:

+886-2-6616-0028 www.ieiworld.com

Sales Email: [email protected]

Page iii


Manual Conventions

WARNING

Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously.

CAUTION

Cautionary messages should be heeded to help reduce the chance of losing data or damaging the product.

NOTE

These messages inform the reader of essential but non-critical information. These messages should be read carefully as any directions or instructions contained therein can help avoid making mistakes.

HOT SURFACE

This symbol indicates a hot surface that should not be touched without taking care.

OPERATING INSTRUCTION

Follow operating instructions or consult instructions for use.

Page iv


Table of Contents

1 INTRODUCTION.......................................................................................................... 1

1.1

O

VERVIEW

.................................................................................................................. 2

1.2

M

ODEL

V

ARIATIONS

................................................................................................... 3

1.3

F

EATURES

................................................................................................................... 3

1.4

F

RONT

P

ANEL

............................................................................................................. 4

1.4.1 Backlit Touch Buttons ........................................................................................ 5

1.5

S

IDE

P

ANELS

.............................................................................................................. 6

1.6

B

OTTOM

P

ANEL

.......................................................................................................... 6

1.7

R

EAR

P

ANEL

............................................................................................................... 7

1.8

S

YSTEM

S

PECIFICATIONS

............................................................................................ 8

1.9

D

IMENSIONS

..............................................................................................................11

2 UNPACKING ............................................................................................................... 12

2.1

U

NPACKING

.............................................................................................................. 13

2.2

P

ACKING

L

IST

........................................................................................................... 14

2.3

O

PTIONAL

I

TEMS

...................................................................................................... 15

3 INSTALLATION ......................................................................................................... 18

3.1

A

NTI

-

STATIC

P

RECAUTIONS

...................................................................................... 19

3.2

I

NSTALLATION

P

RECAUTIONS

................................................................................... 19

3.3

I

NSTALLATION AND

C

ONFIGURATION

S

TEPS

............................................................. 20

3.4

HDD I

NSTALLATION

................................................................................................. 20

3.5

H

ANDSET

I

NSTALLATION

(O

PTIONAL

) ...................................................................... 22

3.5.1 Using VoIP Handset ......................................................................................... 24

3.6

H

ANDLE

I

NSTALLATION

(O

PTIONAL

)........................................................................ 28

3.6.1 Barcode Reader Installation ............................................................................ 29

3.6.2 Reading Light................................................................................................... 31

3.7

3-

IN

-1 C

OMBO

R

EADER

I

NSTALLATION

(O

PTIONAL

) ................................................ 31

3.8

U

SING

RFID R

EADER

(O

PTIONAL

)........................................................................... 33

3.9

RS-232/422/485 S

ERIAL

P

ORT

C

ONNECTION

........................................................... 36

3.10

AT/ATX M

ODE

S

ELECTION

.................................................................................... 36

Page v


3.10.1 AT Power Mode.............................................................................................. 36

3.10.2 ATX Power Mode ........................................................................................... 37

3.11

C

ABLE

C

OVER

I

NSTALLATION

................................................................................ 37

3.12

M

OUNTING THE

S

YSTEM

........................................................................................ 39

3.12.1 Wall Mounting................................................................................................ 39

3.12.2 Arm Mounting ................................................................................................ 42

3.12.3 Stand Mounting .............................................................................................. 44

3.13

P

OWERING

O

N THE

S

YSTEM

................................................................................... 45

3.14

R

ESET THE

S

YSTEM

................................................................................................ 46

4 BIOS SETUP ................................................................................................................ 47

4.1

I

NTRODUCTION

......................................................................................................... 48

4.1.1 Starting Setup ................................................................................................... 48

4.1.2 Using Setup ...................................................................................................... 48

4.1.3 Getting Help..................................................................................................... 49

4.1.4 BIOS Menu Bar................................................................................................ 49

4.2

M

AIN

........................................................................................................................ 50

4.3

A

DVANCED

............................................................................................................... 51

4.3.1 Trusted Computing ........................................................................................... 52

4.3.2 ACPI Settings ................................................................................................... 53

4.3.3 F81866 Super IO Configuration ...................................................................... 54

4.3.3.1 Serial Port n Configuration ....................................................................... 54

4.3.3.1.1 Serial Port 1 Configuration ................................................................ 55

4.3.3.1.2 Serial Port 2 Configuration ................................................................ 56

4.3.4 F81866 H/W Monitor....................................................................................... 57

4.3.5 RTC Wake Settings ........................................................................................... 58

4.3.6 Serial Port Console Redirection ...................................................................... 59

4.3.6.1 Console Redirection Settings .................................................................... 60

4.3.6.2 Legacy Console Redirection Settings ....................................................... 62

4.3.7 CPU Configuration .......................................................................................... 63

4.3.8 SATA Configuration ......................................................................................... 65

4.3.9 USB Configuration........................................................................................... 67

4.3.10 IEI Feature ..................................................................................................... 68

4.4

C

HIPSET

................................................................................................................... 69

4.4.1 System Agent (SA) Configuration .................................................................... 70

Page vi


4.4.1.1 Graphics Configuration............................................................................. 71

4.4.1.1.1 LCD Control ...................................................................................... 73

4.4.1.2 Memory Configuration ............................................................................. 74

4.4.2 PCH-IO Configuration .................................................................................... 74

4.4.2.1 PCI Express Configuration ....................................................................... 75

4.4.2.2 HD Audio Configuration........................................................................... 76

4.5

S

ECURITY

................................................................................................................. 77

4.6

B

OOT

........................................................................................................................ 78

4.7

S

AVE

& E

XIT

............................................................................................................ 80

5 DRIVER INSTALLATION......................................................................................... 82

5.1

A

VAILABLE

S

OFTWARE

D

RIVERS

.............................................................................. 83

5.2

I

NTEL

® C

HIPSET

D

RIVER

......................................................................................... 84

5.3

I

NTEL

® G

RAPHICS

D

RIVER

...................................................................................... 85

5.4

A

UDIO

D

RIVER

......................................................................................................... 86

5.5

LAN D

RIVER

........................................................................................................... 87

5.6

I

NTEL

® M

ANAGEMENT

E

NGINE

............................................................................... 88

5.7

W

IRELESS

LAN D

RIVER

.......................................................................................... 89

5.8

B

LUETOOTH

D

RIVER

................................................................................................ 90

5.9

K

EYPAD

AP .............................................................................................................. 91

5.10

RFID D

RIVER

(O

PTIONAL

)..................................................................................... 92

5.11

3-

IN

-1 C

OMBO

R

EADER

D

RIVER

(O

PTIONAL

) ......................................................... 95

5.11.1 SCR Driver ..................................................................................................... 95

5.11.2 MSR Driver .................................................................................................... 99

5.11.3 Fingerprint Reader Driver ........................................................................... 102

5.12

B

ARCODE

R

EADER

D

RIVER

(O

PTIONAL

) .............................................................. 104

6 SYSTEM MAINTENANCE ..................................................................................... 106

6.1

S

YSTEM

M

AINTENANCE

I

NTRODUCTION

................................................................ 107

6.2

A

NTI

-

STATIC

P

RECAUTIONS

.................................................................................... 107

6.3

T

URN OFF THE

P

OWER

............................................................................................ 108

6.4

R

EMOVING THE

C

OVERS

........................................................................................ 108

6.5

SO-DIMM R

EPLACEMENT

......................................................................................110

6.6

PCI

E

M

INI

C

ARD

I

NSTALLATION

.............................................................................111

6.7

R

EINSTALLING THE

C

OVERS

....................................................................................112

Page vii


7 INTERFACE CONNECTORS ..................................................................................113

7.1

P

ERIPHERAL

I

NTERFACE

C

ONNECTORS

....................................................................114

7.2

I

NTERNAL

P

ERIPHERAL

C

ONNECTORS

.....................................................................115

7.2.1 Audio Connector (AUDIO_OUT1) .................................................................116

7.2.2 Audio Out Connector (AMP_OUT1) ..............................................................116

7.2.3 Battery Connector (BAT1) ..............................................................................116

7.2.4 Debug Connector (DBG_PORT1) ..................................................................117

7.2.5 Inverter Connector (INVERTER1)..................................................................117

7.2.6 LVDS Connector (LVDS1) ..............................................................................117

7.2.7 MCU Connector (HOTKEY_CN1) .................................................................118

7.2.8 MCU Flash Connector (JP8)..........................................................................119

7.2.9 MCU Flash SPI ROM Connector (MCU_SPI1) .............................................119

7.2.10 Microphone Connector (DMIC1) .................................................................119

7.2.11 Power Button Connector (PWR_BTN1)....................................................... 120

7.2.12 Power LED Connector (PW_LED1)............................................................ 120

7.2.13 RS-232 Serial Port Connector (COM2)....................................................... 120

7.2.14 SATA Connectors (SATA1 & SATA2) ........................................................... 121

7.2.15 SPI Flash Connector (JSPI1)....................................................................... 121

7.2.16 TPM Connector (TPM1) .............................................................................. 121

7.2.17 USB Connector (BT_USB1)......................................................................... 122

7.2.18 USB Connector (CAM_USB1) ..................................................................... 122

7.2.19 USB Connector (RFID_USB1) .................................................................... 123

7.2.20 USB Connector (TOUCH_USB1)................................................................ 123

7.3

E

XTERNAL

I

NTERFACE

P

ANEL

C

ONNECTORS

.......................................................... 123

7.3.1 GbE Connectors (LAN1 & LAN2) ................................................................. 124

7.3.2 HDMI Output Connector (HDMI_OUT1) ..................................................... 124

7.3.3 Power Connector (PWR1) ............................................................................. 125

7.3.4 RS-232/422/485 DB-9 Serial Port (COM1)................................................... 125

7.3.5 USB 2.0 Connectors (USB20_CN1) .............................................................. 125

7.3.6 USB 3.0 Connectors (USB_CON1)................................................................ 126

7.3.7 USB 3.0 Connectors (USB_CON2)................................................................ 126

7.4

P

RECONFIGURED

J

UMPER

S

ETTINGS

....................................................................... 127

7.4.1 Flash Descriptor Security Override Jumper (ME_FLASH1) ........................ 127

7.4.2 LVDS Panel Voltage Selection Jumper (J_VLVDS1) ..................................... 127

Page viii


7.4.3 LVDS Panel Resolution Selection Jumper (SW1) .......................................... 128

7.4.4 PCIe Mini/mSATA Mode Selection (MSATA_CN1) ....................................... 128

A REGULATORY COMPLIANCE ............................................................................ 129

B SAFETY PRECAUTIONS ....................................................................................... 134

B.1

S

AFETY

P

RECAUTIONS

........................................................................................... 135

B.1.1 General Safety Precautions ........................................................................... 135

B.1.2 Anti-static Precautions .................................................................................. 136

B.1.3 Product Disposal ........................................................................................... 137

B.1.4 Classification ................................................................................................. 138

B.2

M

AINTENANCE AND

C

LEANING

P

RECAUTIONS

...................................................... 138

B.2.1 Maintenance and Cleaning............................................................................ 139

B.2.2 Cleaning Tools ............................................................................................... 139

C BIOS MENU OPTIONS ........................................................................................... 140

D WATCHDOG TIMER .............................................................................................. 143

E HAZARDOUS MATERIALS DISCLOSURE ....................................................... 146

Page ix


List of Figures

Figure 1-1: POC-17C-ULT3 Medical Panel PC .............................................................................2

Figure 1-2: Front View ....................................................................................................................4

Figure 1-3: Backlit Touch Buttons ................................................................................................5

Figure 1-4: Side View......................................................................................................................6

Figure 1-5: Bottom Panel ...............................................................................................................7

Figure 1-6: Rear View .....................................................................................................................7

Figure 1-7: Dimensions (mm) ......................................................................................................11

Figure 3-1: HDD Cover Retention Screws..................................................................................20

Figure 3-2: HDD Bracket Retention Screws...............................................................................21

Figure 3-3: HDD Retention Screws .............................................................................................21

Figure 3-4: HDD Installation ........................................................................................................22

Figure 3-5: Handset Holder Retention Screws ..........................................................................23

Figure 3-6: Handset Installation ..................................................................................................23

Figure 3-7: Handset Driver Folder...............................................................................................24

Figure 3-8: Handset Driver Installation.......................................................................................25

Figure 3-9: Allow API Access ......................................................................................................25

Figure 3-10: Manage Program Access to Skype .......................................................................26

Figure 3-11: Handle Installation ..................................................................................................28

Figure 3-12: Insert Barcode Reader Set .....................................................................................29

Figure 3-13: Install and Connect Barcode Reader Set..............................................................30

Figure 3-14: Barcode Reader Button ..........................................................................................30

Figure 3-15: Reading Light ..........................................................................................................31

Figure 3-16: 3-in-1 Combo Reader ..............................................................................................31

Figure 3-17: USB Ports on the Side Panel .................................................................................32

Figure 3-18: Combo Reader Installation ....................................................................................32

Figure 3-19: RFID Program Location ..........................................................................................33

Figure 3-20: IRFR-100 Icon ..........................................................................................................33

Figure 3-21: IRFR Screen.............................................................................................................34

Figure 3-22: IRFR – Find Tags.....................................................................................................34

Figure 3-23: IRFR – UIDs..............................................................................................................35

Figure 3-24: AT/ATX Switch Location.........................................................................................36

Page x


Figure 3-25: Aligning the Tab on the Bottom Panel..................................................................37

Figure 3-26: Cable Cover Installation .........................................................................................38

Figure 3-27: Cable Cover Removal .............................................................................................38

Figure 3-28: Wall-mounting Bracket ...........................................................................................40

Figure 3-29: Chassis Support Screws ........................................................................................41

Figure 3-30: Secure the Panel PC ...............................................................................................42

Figure 3-31: VESA 75 and VESA 100 Mounting Retention Screw Holes.................................43

Figure 3-32: Arm Mounting..........................................................................................................44

Figure 3-33: Powering On the System........................................................................................45

Figure 3-34: Reset Button Location............................................................................................46

Figure 5-1: Available Drivers .......................................................................................................83

Figure 5-2: Intel® Chipset Device Software Installation Wizard ..............................................84

Figure 5-3: Intel® Graphics Driver Installation Wizard .............................................................85

Figure 5-4: Realtek HD Audio Driver InstallShield Wizard .......................................................86

Figure 5-5: LAN Driver Installation Wizard ................................................................................87

Figure 5-6: Intel® ME Components Installation Wizard............................................................88

Figure 5-7: Wireless LAN InstallShield Wizard..........................................................................89

Figure 5-8: Bluetooth Driver InstallShield Wizard.....................................................................90

Figure 5-9: Keypad AP Setup Wizard .........................................................................................91

Figure 5-10: Keypad AP ...............................................................................................................91

Figure 5-11: Device Manager - Update Driver Software............................................................92

Figure 5-12: Update Driver Software Window ...........................................................................93

Figure 5-13: Browse for Driver Software Window.....................................................................93

Figure 5-14: Driver Installation Complete Window ...................................................................94

Figure 5-15: Device Manager Window–RFID Devices...............................................................94


Figure 5-17: Update Driver Software Window ...........................................................................96

Figure 5-18: Browse for Driver Software Window.....................................................................96

Figure 5-19: Installing Driver Window ........................................................................................97

Figure 5-20: Driver Installation Complete Window ...................................................................97

Figure 5-21: Device Manager Window–SCR Device..................................................................98


Figure 5-23: Update Driver Software Window ........................................................................ 100

Figure 5-24: Browse for Driver Software Window.................................................................. 100

Figure 5-25: Installing Driver Window ..................................................................................... 101

Page xi


Figure 5-26: Driver Installation Complete Window ................................................................ 101

Figure 5-27: Device Manager Window–MSR Device .............................................................. 102

Figure 5-28: Fingerprint Reader Driver Folder ....................................................................... 102

Figure 5-29: Fingerprint Reader Driver InstallShield Wizard ................................................ 103

Figure 5-30: Barcode Reader Driver Folder ............................................................................ 104

Figure 5-31: Barcode Reader Driver Installation .................................................................... 104

Figure 5-32: Device Manager Window–Barcode Reader Device .......................................... 105

Figure 6-1: HDD Cover Retention Screws............................................................................... 108

Figure 6-2: Back Cover Retention Screws .............................................................................. 109

Figure 6-3: Aluminum Cover Retention Screws ..................................................................... 109

Figure 6-4: SO-DIMM Slot Locations ....................................................................................... 110

Figure 6-5: SO-DIMM Installation ............................................................................................. 111

Figure 6-6: PCIe Mini Card Slot Location ................................................................................ 111

Figure 6-7: PCIe Mini Card Installation.................................................................................... 112

Figure 7-1: Main Board Layout Diagram ................................................................................. 114

Page xii


List of Tables

Table 1-1: Model Variations ...........................................................................................................3

Table 1-2: Touch Button Functions ..............................................................................................5

Table 1-3: System Specifications................................................................................................10

Table 3-1: Handset Button Functions.........................................................................................27

Table 3-2: RS-232/422/485 Serial Port Pinouts ..........................................................................36

Table 4-1: BIOS Navigation Keys ................................................................................................49

Table 7-1: Peripheral Interface Connectors ............................................................................ 116

Table 7-2: Audio Connector (AUDIO_OUT1) Pinouts............................................................. 116

Table 7-3: Audio Out Connector (AMP_OUT1) Pinouts ......................................................... 116

Table 7-4: Battery Connector (BAT1) Pinouts ........................................................................ 116

Table 7-5: Debug Connector (DBG_PORT1) Pinouts............................................................. 117

Table 7-6: Inverter Connector (INVERTER1) Pinouts............................................................. 117

Table 7-7: LVDS Connector (LVDS1) Pinouts......................................................................... 118

Table 7-8: MCU Connector (HOTKEY_CN1) Pinouts.............................................................. 118

Table 7-9: MCU Flash Connector (JP8) Pinouts ..................................................................... 119

Table 7-10: MCU Flash SPI ROM Connector (MCU_SPI1) Pinouts ....................................... 119

Table 7-11: Microphone Connector (DMIC1) Pinouts ............................................................ 119

Table 7-12: Power Button Connector (PWR_BTN1) Pinouts................................................. 120

Table 7-13: Power LED Connector (PW_LED1) Pinouts ........................................................ 120

Table 7-14: RS-232 Serial Port Connector (COM2) Pinouts .................................................. 120

Table 7-15: SATA Connectors (SATA1 & SATA2) Pinouts .................................................... 121

Table 7-16: SPI Flash Connector (JSPI1) Pinouts .................................................................. 121

Table 7-17: TPM Connector (TPM1) Pinouts........................................................................... 122

Table 7-18: USB Connector (BT_USB1) Pinouts .................................................................... 122

Table 7-19: USB Connector (CAM_USB1) Pinouts................................................................. 122

Table 7-20: USB Connector (RFID_USB1) Pinouts ................................................................ 123

Table 7-21: USB Connector (TOUCH_USB1) Pinouts ............................................................ 123

Table 7-22: Rear Panel Connectors ......................................................................................... 124

Table 7-23: GbE Connectors (LAN1 & LAN2) Pinouts ........................................................... 124

Table 7-24: HDMI Connector (HDMI1) Pinouts........................................................................ 125

Table 7-25: Power Connector (PWR1) Pinouts....................................................................... 125

Page xiii


Table 7-26: RS-232/422/485 DB-9 Serial Port (COM1) Pinouts.............................................. 125

Table 7-27: USB 2.0 Connector (USB20_CN1) Pinouts.......................................................... 125

Table 7-28: USB 3.0 Connector (USB_CON12) Pinouts......................................................... 126

Table 7-29: USB 3.0 Connector (USB_CON2) Pinouts........................................................... 126

Table 7-30: Preconfigured Jumpers ........................................................................................ 127

Table 7-31: Flash Descriptor Security Override Jumper (ME_FLASH1) Settings ............... 127

Table 7-32: LVDS Voltage Selection Jumper (J_VLVDS1) Settings ..................................... 127

Table 7-33: LVDS Resolution Selection Jumper (SW1) Settings.......................................... 128

Table 7-34: PCIe Mini/mSATA Mode Selection (MSATA_CN1) Settings .............................. 128

Page xiv


List of BIOS Menus

BIOS Menu 1: Main .......................................................................................................................50

BIOS Menu 2: Advanced ..............................................................................................................51

BIOS Menu 3: Trusted Computing ..............................................................................................52

BIOS Menu 4: ACPI Settings .......................................................................................................53

BIOS Menu 5: F81866 Super IO Configuration ..........................................................................54

BIOS Menu 6: Serial Port n Configuration Menu.......................................................................54

BIOS Menu 7: F81866 H/W Monitor.............................................................................................57

BIOS Menu 8: RTC Wake Settings ..............................................................................................58

BIOS Menu 9: Serial Port Console Redirection .........................................................................59

BIOS Menu 10: Console Redirection Settings...........................................................................60

BIOS Menu 11: Legacy Console Redirection Settings .............................................................62

BIOS Menu 12: CPU Configuration .............................................................................................63

BIOS Menu 13: SATA Configuration ...........................................................................................65

BIOS Menu 14: USB Configuration .............................................................................................67

BIOS Menu 15: IEI Feature...........................................................................................................68

BIOS Menu 16: Chipset ................................................................................................................69

BIOS Menu 17: System Agent (SA) Configuration ....................................................................70

BIOS Menu 18: Graphics Configuration .....................................................................................71

BIOS Menu 19: LCD Control ........................................................................................................73

BIOS Menu 20: Memory Configuration.......................................................................................74

BIOS Menu 21: PCH-IO Configuration ........................................................................................74

BIOS Menu 22: PCI Express Configuration ...............................................................................75

BIOS Menu 23: HD Audio Configuration ....................................................................................76

BIOS Menu 24: Security ...............................................................................................................77

BIOS Menu 25: Boot .....................................................................................................................78

BIOS Menu 26: Save & Exit..........................................................................................................80

Page xv


Chapter

1

1

Introduction

Page 1

1.1 Overview


Figure 1-1: POC-17C-ULT3 Medical Panel PC

The POC-17C-ULT3 is a 6 th

generation Intel® Core™/Celeron® mobile CPU powered medical-grade panel PC with a rich variety of functions and peripherals. All

POC-17C-ULT3 models are designed for easy and simplified integration into point-of-care

(POC) applications. The system comes with 4 GB of preinstalled DDR4 memory and supports a maximum of 32 GB ensuring smooth data throughputs with reduced bottlenecks and fast system access.

One RS-232/422/485 serial port, four USB 3.0 ports and four USB 2.0 ports provide simplified connectivity to a variety of external peripheral devices. Wi-Fi 802.11a/b/g/n/ac high speed wireless and two RJ-45 GbE connectors allow for smooth connection of the system to an external LAN. The system also equips with two SATA interfaces, supporting both SATA HDD and SSD.

NOTE:

The POC-17C-ULT3 medical panel PC is intended to be used to display general purpose medical images. The device shall not be used for diagnosis purpose or life supporting system.

Page 2


1.2 Model Variations

There are three models in the POC-17C-ULT3 series. All models are preinstalled with one

4 GB DDR4 memory module and an 802.11a/b/g/n/ac Wi-Fi module. The model numbers and model variations are listed below.

Model CPU

POC-17C-ULT3-i7/PC/4G Intel® Core™ i7-6600U

POC-17C-ULT3-i5/PC/4G Intel® Core™ i5-6300U

POC-17C-ULT3-C/PC/4G Intel® Celeron® 3855U

Table 1-1: Model Variations

1.3 Features

The POC-17C-ULT3 features are listed below:

17” (5:4) flat-bezel LCD with LED backlight

Anti-bacteria

Projected capacitive type touchscreen

Intel

®

Core™ i7-6600U/i5-6300U or Intel

®

Celeron

®

3855U processor

Preinstalled with 4 GB of DDR4 memory (system max. 32 GB)

Two GbE RJ-45 connectors and Wi-Fi 802.11a/b/g/n/ac high speed wireless

Two internal 2 W speakers

Four USB 3.0 ports and four USB 2.0 ports

RAID funciton supported (RAID 0/1)

12 V ~ 28 V wide range DC power input

One RS-232/422/485 DB-9 connector

IP 65 compliant front panel

Optional Mifare RFID reader

Optional 3-in-1 card reader (supports magnetic stripe card, smart card and fingerprint)

Optional VoIP phone handset

Optional handle module with 1D/2D barcode scanner and reading light

Page 3


1.4 Front Panel

The front side of the POC-17C-ULT3 is a flat-bezel panel with a TFT LCD screen

surrounded by a PC+ABS plastic frame ( Figure 1-2 ).

Figure 1-2: Front View

Page 4


1.4.1 Backlit Touch Buttons

The front panel of the POC-17C-ULT3 contains several backlit touch buttons that control audio volume, LCD brightness and some other system components.

Figure 1-3: Backlit Touch Buttons

The following table describes the function of each button.

Button Function

LCD on/off

(the touch buttons blink when the LCD is turned off)

− : Brightness down or lock/unlock OSD (with function key)

(minimum brightness: 5%)

+: Brightness up (maximum brightness: 100%)

− : Volume down

+: Volume up

Touch lock for cleaning: long-press for 3 seconds to lock or unlock the touch function of the screen. The touch buttons blink when the touch function is locked. The lock will be automatically disabled after 2 minutes.

Lock or unlock the touch buttons: long-press for 3 seconds to lock or unlock the touch buttons. The touch buttons blink when the touch buttons are locked.

Power on: long-press for 3 seconds. All touch buttons blink

3 times, and the system starts to boot.

Power off: long-press for 3 seconds. All touch buttons blink

3 times, and the system starts to shut down.

Note: Press the touch button for at least one second to activate it.

Table 1-2: Touch Button Functions

Page 5


1.5 Side Panels

The left side panel has two USB 2.0 ports which are protected by a waterproof cover and the IEI E-Window for I/O interface expansion by installing a PCIe Mini card. In addition, the

POC-17C-ULT3 equips with two 2 W speakers located on the side panels as shown in

Figure 1-4 .

Figure 1-4: Side View

1.6 Bottom Panel

The bottom panel of the POC-17C-ULT3 has the following connectors and switches

(

Figure 1-5 ):

1 x 12 V ~ 28 V DC input power jack

1 x RS-232/422/485 DB-9 connector

1 x Barcode reader RJ-11 connector

2 x GbE RJ-45 connectors

4 x USB 3.0 connectors


Page 6


1 x HDMI output connector

1 x AT/ATX switch

1 x Reset button

Figure 1-5: Bottom Panel

1.7 Rear Panel

The rear panel contains the power button, camera cover on/off switch and the retention screw holes that support VESA 75/100 mounting (

Figure 1-6

). Besides, the rear panel has several screw holes for installing the optional items, such as the 3-in-1 reader. For detailed information on installation of the optional items, please refer to Chapter 3.

Figure 1-6: Rear View

Page 7


1.8 System Specifications

The technical specifications for the POC-17C-ULT3 systems are listed in

Table 1-3

.

LCD and Touchscreen

LCD Size

Max. Resolution

Brightness (cd/m

2

)

Contrast Ratio

LCD Color

Pixel Pitch (mm)

Viewing Angle (H-V)

Backlight MTBF

Touchscreen

Touch Controller

Surface Hardness

System

CPU

Memory

I/O Ports

Storage

17" (5:4)

1280 (W) x 1024 (H)

350

1000:1

16.7M (RGB 6-bit)

0.264 (H) x 0.264 (V)

170°/160°

30,000 hrs (LED backlight)

Projected capacitive type with USB interface

ILITEK

6H

Intel® Core™ i7-6600U/i5-6300U or Intel® Celeron® 3855U

Two 260-pin 2133/1866 MHz dual-channel non-ECC unbuffered DDR4 SO-DIMMs supported (system max. 32 GB)

Preinstalled with 4 GB memory

1 x 12 V ~ 28 V DC input jack

1 x Barcode reader connector (RJ-11)

1 x HDMI output connector

1 x RS-232/422/485 serial port (DB-9 connector)

2 x GbE LAN (RJ-45 connector)


4 x USB 2.0 connectors (2 on side panel)

Two 2.5” SATA 6Gb/s HDD bays

One mSATA (reserved, PCIe Mini interface)

Page 8


Audio

Webcam & Microphone

Expansion Interface

LED Indicator

Two 2 W speakers

2-megapixel CMOS front-facing camera with auto focus and digital microphone

One PCIe Mini slot (reserved)

RFID LED indicator (optional)

Other Features

Mifare RFID Optional Mifare 13.56 MHz card reader (with LED indicator)

1 x LCD on/off

1 x Brightness up

1 x Brightness down

1 x Volume up

1 x Volume down

1 x Touch lock for cleaning

Function Keys

Combinations:

1 x Lock/unlock OSD

1 x Power on/off

Light Sensor

Cooling Method

Ambient light sensor for panel brightness adjustment

Fanless

Connectivity

Wi-Fi and Bluetooth

LAN

IEEE 802.11a/b/g/n/ac 2T2R module with Bluetooth v4.1

(M.2 2230 A-E key module)

Two GbE LAN connectors

Physical

Construction Material

Mounting

PC+ABS plastic with anti-bacterial material

Wall, stand and arm mounting

VESA 75 mm x 75 mm or 100 mm x 100 mm

Net Weight 5.8 kg

Dimensions (W x H x D)

435 mm x 376 mm x 64.5 mm

Page 9


Environment

Storage/Transportation

Temperature -20ºC ~ 60ºC

Humidity 10% ~ 95% (non-condensing)

Pressure 700 hPa ~ 1060 hPa

Temperature 0ºC ~ 40ºC

Operating Humidity 10% ~ 95% (non-condensing)

Vibration

Shock

Pressure 700 hPa ~ 1060 hPa

1G

Operating Shock: 5G peak acceleration (11ms duration)

Non-Operating Shock: 15G peak acceleration (11ms duration)

IP 65 compliant front panel IP Level

Power

Power Input

Power Adapter

12 V ~ 28 V DC

120 W medical-grade power adapter

( P/N : 63040-010120-010-RS)

150 W medical-grade power adapter

( P/N : 63040-010150-400-RS)

Input : 100 V AC ~ 240 V AC,

47 Hz ~ 63 Hz, 1.4 A ~ 0.6 A

Input : 100 V AC ~ 240 V AC,

47 Hz ~ 63 Hz, 2 A ~ 0.85 A

Output : 19 V 6.32 A Output : 19 V 7.89 A

Table 1-3: System Specifications

Page 10


1.9 Dimensions

The POC-17C-ULT3 dimensions are shown below.

Figure 1-7: Dimensions (mm)

Page 11


Chapter

2

2

Unpacking

Page 12


2.1 Unpacking

To unpack the medical panel PC, follow the steps below:

WARNING!

The front side LCD screen has a protective plastic cover stuck to the screen. Only remove the plastic cover after the medical panel PC has been properly installed. This ensures the screen is protected during the installation process.

Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the external (second) box.

Step 2: Open the external (second) box.

Step 3: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the internal (first) box.

Step 4: Lift the monitor out of the boxes.

Step 5: Remove both polystyrene ends, one from each side.

Step 6: Pull the plastic cover off the medical panel PC.

Step 7: Make sure all the components listed in the packing list are present. Step 0:

Page 13

2.2 Packing List


NOTE:

If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the

POC-17C-ULT3 was purchased from or contact an IEI sales representative directly by sending an email to

[email protected]

.

The POC-17C-ULT3 medical panel PC is shipped with the following components:

Image Quantity Item

1 POC-17C-ULT3 medical panel PC

1

4

120 W/19 V medical-grade power adapter

( P/N : 63040-010120-010-RS) or

150 W/19 V medical-grade power adapter

( P/N : 63040-010150-400-RS)

( P/N : 32702-000200-100-RS)

Pan-head screw (M3*5) for HDD installation

( P/N : 44043-030051-RS)

Page 14


1 Quick Installation Guide

1 One Key Recovery CD

2.3 Optional Items

The following are optional components which may be separately purchased:

Item and Part Number

3-in-1 reader (smart card, magnetic card and fingerprint)

( P/N : MEDP-CR-R10)

Image

Handle

( P/N : MEDP-HD-R10)

Handle with 1D/2D barcode reader and reading light

( P/N : MEDP-HD-BR-R10)

Page 15


Handset (USB interface) and holder

( P/N : MEDP-HS-R10)


Image

VESA 100 wall mount kit (four M3*6 screws included)

( P/N : AFLWK-19B)

Arm

( P/N : ARM-31-RS)

Stand

( P/N : STAND-A21-R10)

EZ Stand with cabling hole, VESA 100

( P/N : MEDP-EZS-R10)

Page 16



Trusted platform module (assemble-to-order)

( P/N : MEDP-TPM-R10)

Mifare RFID reader compliant with ISO 14443A, ISO

14443B and ISO 15693 protocols (assemble-to-order)

( P/N : MEDP-MF-RFID-R10)

Cable cover

Image

Page 17


Chapter

3

3

Installation

Page 18


3.1 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the maintenance of the

POC-17C-ULT3 may result in permanent damage to the

POC-17C-ULT3 and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components, including the POC-17C-ULT3. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the POC-17C-ULT3 is accessed internally, or any other electrical component is handled, the following anti-static precautions are strictly adhered to.

Wear an anti-static wristband : Wearing a simple anti-static wristband can help to prevent ESD from damaging the board.

Self-grounding : Before handling the board, touch any grounded conducting material. During the time the board is handled, frequently touch any conducting materials that are connected to the ground.

Use an anti-static pad : When configuring the POC-17C-ULT3, place it on an anti-static pad. This reduces the possibility of ESD damaging the POC-17C-ULT3.

Only handle the edges of the PCB : When handling the PCB, hold the PCB by the edges.

3.2 Installation Precautions

When installing the medical panel PC, please follow the precautions listed below:

Manufacturer authorization : Do not modify this equipment without authorization of manufacturer.

Certified Engineers : Only certified engineers should install and modify the hardware settings.

Power turned off : When installing the medical panel PC, make sure the power is off. Failing to turn off the power may cause severe injury to the body and/or damage to the system.

Page 19


Anti-static Discharge : If a user open the rear panel of the medical panel PC, to configure the jumpers or plug in added peripheral devices, ground themselves first and wear an anti-static wristband.

3.3 Installation and Configuration Steps

The following installation steps must be followed.

Step 1: Unpack the medical panel PC.

Step 2: Install an HDD.

Step 3: Install necessary accessories (handset, handle or combo reader).

Step 4: Configure the system.

Step 5: Connect peripheral devices to the medical panel PC.

Step 6: Mount the medical panel PC.

Step 0:

3.4 HDD Installation

To install the HDD into the system, please follow the steps below:

Step 1:

Remove the three retention screws from the HDD cover ( Figure 3-1 ).

Figure 3-1: HDD Cover Retention Screws

Page 20


Step 2: Remove the HDD cover. The POC-17C-ULT3 equips with two 2.5” HDD bays.

Select one to install the HDD.

Step 3:

Remove the three HDD bracket retention screws ( Figure 3-2

) and lift the HDD bracket off the panel PC.

Figure 3-2: HDD Bracket Retention Screws

Step 4: Slide the HDD into the HDD bracket, aligning the four retention screw holes in the both sides of the HDD bracket with the retention screw holes on the sides of

the HDD ( Figure 3-3 ).

Step 5: Insert four retention screws (M3*5) into the bracket (

Figure 3-3

).

Figure 3-3: HDD Retention Screws

Page 21


Step 6: Replace the HDD bracket by securing the three retention screws previously removed. Then, connect the SATA cable from the POC-17C-ULT3 to the rear of

the HDD ( Figure 3-4

).

Figure 3-4: HDD Installation

Step 7: Replace the HDD cover. Step 0:

3.5 Handset Installation (Optional)

An optional phone handset can be installed on the side of the POC-17C-ULT3 to make

VoIP calls. To install the handset and the holder, please follow the instruction below.

Step 1: Locate the two retention screw holes for installing the handset holder on the rear

panel ( Figure 3-5 ).

Page 22


Step 2: Secure the handset holder with the POC-17C-ULT3 by two retention screws

(M3*8, flat head).

Figure 3-5: Handset Holder Retention Screws

Step 3: Plug the handset cord into a USB connector on the bottom panel.

Step 4: Place the handset in the holder.

Figure 3-6: Handset Installation

Page 23


3.5.1 Using VoIP Handset

The VoIP handset is designed for Skype. To use the handset to place or receive a call via

Skype, please follow the steps below.

Step 1: Install the Skype program ( http://www.skype.com/en/ ).

Step 2: Select Other from the list of the driver CD. Double click the setup file in the

POCP-W22A-HS-R10_U-2000H folder to install the handset driver (

Figure 3-7 ).

Figure 3-7: Handset Driver Folder

Step 3:

Follow the step-by-step instruction of the installation wizard ( Figure 3-8

) to install the handset driver.

Page 24


Figure 3-8: Handset Driver Installation

Step 4: Launch Skype. Press the Allow access button on Skype (

Figure 3-9

) to allow handset API access.

Figure 3-9: Allow API Access

Page 25


API access can also be managed through Tools Æ Options Æ Advanced settings in Skype. See

Figure 3-10 .

Figure 3-10: Manage Program Access to Skype

Page 26


Step 5: The user can now use Skype via the handset. The function description of each button on the handset is listed in the following table.

Button Function

LED indicator :

Clear – no call activity

Blinking green – incoming call ringing

Steady green – active call

Hot key :

No call activity – launch Skype and select menus

* long-press the hot key for 2 seconds to turn off Skype

Ringing – terminate the incoming call

Active call – mute or unmute the handset microphone i j

No call activity – scroll up through incoming and outgoing call history

Active call – handset speaker volume up

No call activity – scroll down through incoming and outgoing call history

Active call – handset speaker volume down

Place, answer or hang up a call.

Table 3-1: Handset Button Functions

Page 27


3.6 Handle Installation (Optional)

An optional handle can be installed on the POC-17C-ULT3 for the user to easily adjust the viewing angle and the position of the POC-17C-ULT3. To install the handle, please follow the instruction below.

Step 1: Locate the retention screw holes for installing the handle on the rear panel

(

Figure 3-11 ). If a cable cover is installed on the rear panel, please remove it

first.

Step 2: Secure the handle with the POC-17C-ULT3 by inserting eight retention screws

(M3*6L, flat head).

Figure 3-11: Handle Installation

Page 28


3.6.1 Barcode Reader Installation

The optional handle may come with a barcode reader set which also contains a reading light with three levels of brightness. To install the barcode reader set, please follow the instruction below.

Step 1: Follow the instruction described in

Section 3.6

to install the handle.

Step 2: Insert the barcode reader set into the slot in the center of the handle. To be able to insert the barcode reader, the side with barcode reader must face toward the

right side of the POC-17C-ULT3 as shown in Figure 3-12 .

Figure 3-12: Insert Barcode Reader Set

Step 3: Push the barcode reader set all the way down, and then rotate the barcode

reader anti-clockwise to a proper position ( Figure 3-13

).

Step 4: Connect the barcode reader cable to the RJ-11 connector on the bottom panel of

the POC-17C-ULT3 ( Figure 3-13

).

Page 29


Figure 3-13: Install and Connect Barcode Reader Set

Step 5: Install the driver for the barcode reader by following the instructions described in

Section 5.12

.

Step 6: After driver installation is complete, push the barcode reader button to trigger the barcode reader.

Figure 3-14: Barcode Reader Button

WARNING:

Do not stare into beam of the laser light. The human eye can be damaged. Avoid that the laser beam hits reflective surfaces such as mirrors, etc. Any changes at the device are forbidden these could cause a dangerous laser light.

Page 30


3.6.2 Reading Light

The barcode reader is also equipped with a reading light with 3-level of brightness. Push the reading light button to turn on or to toggle illumination brightness levels.

Figure 3-15: Reading Light

3.7 3-in-1 Combo Reader Installation (Optional)

The 3-in-1 combo reader is an optional item for the POC-17C-ULT3. The combo reader combines fingerprint reader, smart card reader (SCR) and magnetic stripe reader (MSR) into one compact device.

Figure 3-16: 3-in-1 Combo Reader

Page 31


To install the combo reader to the POC-17C-ULT3, please follow the steps below.

Step 1: Open the USB port cover on the side panel of the POC-17C-ULT3.

Figure 3-17: USB Ports on the Side Panel

Step 2: Align the USB connectors on the reader with the two USB connectors on the side panel of the POC-17C-ULT3.

Step 3: Insert and connect the USB connectors to install the combo reader.

Step 4: Secure the combo reader to the system by inserting two retention screws

(M3x5L) into the rear panel of the POC-17C-ULT3 and tightening them.

Figure 3-18: Combo Reader Installation

Page 32


Step 5: Install the drivers for these three readers by following the instructions described in Chapter 5 :

Section : SCR Driver

Section : MSR Driver

Section : Fingerprint Reader Driver

3.8 Using RFID Reader (Optional)

The POC-17C-ULT3 may come with an optional RFID reader pre-installed inside the

bottom left corner of the front panel ( Figure 1-2

). To use the RFID reader, follow the steps below.

Step 1: Install the RFID driver (refer to

Section 5.10

).

Step 2: Locate the IRFR-100.exe file in the following folder of the driver CD:

\Docs\12.Other\POCP-MF-RFID-R10\RFID\D490. Copy the IRFR-100.exe

program to the desktop.

Figure 3-19: RFID Program Location

Step 3: Double click the IRFR-100 icon on the desktop.

Figure 3-20: IRFR-100 Icon

Page 33


Step 4:

The IRFR-100 window appears ( Figure 3-21 ).

Figure 3-21: IRFR Screen

Step 5: Select the Find tags tab and click the Run button to enable the RFID reader

(

Figure 3-22 ).

Figure 3-22: IRFR – Find Tags

Page 34


Step 6: Place an RFID card near the RFID reader on the bottom right corner of the

front panel ( Figure 1-2 ) then remove it. The card number will be shown in the

UIDs column ( Figure 3-23 ).

Figure 3-23: IRFR – UIDs

NOTE:

Please refer to the IRFR-100 user guide in the driver CD

(IRFR-100_AP_UserGuide.pdf) for detailed instruction on how to use the IRFR-100.

Page 35


3.9 RS-232/422/485 Serial Port Connection

The bottom panel of the POC-17C-ULT3 has one DB-9 male connectors for

RS-232/422/485 connection. The serial communication mode selection can be made through the BIOS options. Please refer to

Section 4.3.3.1.1

for detailed information. The

pinouts of the DB-9 connector are listed below.

Pin RS-232 RS-422 RS-485

2 RX

3 TX RXD422+

4 DTR RXD422-

5 GND

6 DSR

7 RTS

8 CTS

9 RI

Table 3-2: RS-232/422/485 Serial Port Pinouts

3.10 AT/ATX Mode Selection

AT or ATX power mode can be used on the POC-17C-ULT3. The selection is made through an AT/ATX switch located on the bottom panel (

Figure 3-24 ).

Figure 3-24: AT/ATX Switch Location

3.10.1 AT Power Mode

With the AT mode selected, the power is controlled by a central power unit rather than a power switch. The POC-17C-ULT3 panel PC turns on automatically when the power is connected.

Page 36


3.10.2 ATX Power Mode

With the ATX mode selected, the POC-17C-ULT3 panel PC goes in a standby mode when it is turned off. The panel PC can be easily turned on via network or a power switch in standby mode.

3.11 Cable Cover Installation

An optional cable cover can be installed on the POC-17C-ULT3 for the user to easily manage cables. To install the cable cover, please follow the instruction below.

Step 1: Align the slot on the rear of the cable cover with the tab on the bottom panel of

the POC-17C-ULT3 ( Figure 3-25

). Then, attach the slot to the tab.

Figure 3-25: Aligning the Tab on the Bottom Panel

Step 2: Push six tabs on the cable cover (as shown in

Figure 3-26)

into the slots on the rear panel of the POC-17C-ULT3. More strength is required to push the tabs into the slots.

Page 37


Figure 3-26: Cable Cover Installation

Step 3: To remove the cable cover, push the tabs inwards to release the cover (

Figure

3-27 ), and lift the cover from the POC-17C-ULT3.

Figure 3-27: Cable Cover Removal

Page 38


3.12 Mounting the System

The methods of mounting the POC-17C-ULT3 are listed below.

Wall

Arm

Stand

The mounting methods are described below.

WARNING:

Use suitable mounting apparatus and be sure to secure the screws of the mounting apparatus tightly to avoid risk of injury.

3.12.1 Wall Mounting

To mount the medical panel PC onto the wall, please follow the steps below.

Step 1: Select the location on the wall for the wall-mounting bracket.

Step 2: Carefully mark the locations of the four screw holes in the bracket on the wall.

Step 3: Drill four pilot holes at the marked locations on the wall for the bracket retention screws.

Step 4: Align the wall-mounting bracket screw holes with the pilot holes.

Step 5: Secure the mounting bracket to the wall by inserting the retention screws into

the four pilot holes and tightening them ( Figure 3-28

).

Page 39


Figure 3-28: Wall-mounting Bracket

Step 6: Insert the four monitor mounting screws provided in the wall mount kit into the four screw holes on the real panel of the medical panel PC and tighten until the screw shank is secured against the rear panel (

Figure 3-29 ).

WARNING:

Please use the M4 screws provided in the wall mount kit for the rear panel.

If the screw is missing, the thread depth of the replacement screw should be not more than 4 mm.

Step 7: Align the mounting screws on the monitor rear panel with the mounting holes on the bracket.

Page 40


Step 8: Carefully insert the screws through the holes and gently pull the monitor

downwards until the monitor rests securely in the slotted holes ( Figure 3-29

).

Ensure that all four of the mounting screws fit snugly into their respective slotted holes.

NOTE:

In the diagram below the bracket is already installed on the wall.

Figure 3-29: Chassis Support Screws

Page 41


Step 9: Secure the panel PC by fastening the retention screw of the wall-mounting bracket (

Figure 3-30 ).

Figure 3-30: Secure the Panel PC

3.12.2 Arm Mounting

The POC-17C-ULT3 is VESA (Video Electronics Standards Association) compliant and can be mounted on an arm with a 75 mm or a 100 mm interface pad. To mount the

POC-17C-ULT3 on an arm, please follow the steps below.

Step 1: The arm is a separately purchased item. Please correctly mount the arm onto the surface it uses as a base. To do this, refer to the installation documentation that came with the mounting arm.

Page 42


NOTE:

When purchasing the arm please ensure that it is VESA compliant and that the arm has a 75 mm or a 100 mm interface pad. If the mounting arm is not

VESA compliant it cannot be used to support the POC-17C-ULT3 medical panel PC.

Step 2: Once the mounting arm has been firmly attached to the surface, lift the panel PC onto the interface pad of the mounting arm.

Step 3: Align the retention screw holes on the mounting arm interface with those in the

panel PC ( Figure 3-31

).

Figure 3-31: VESA 75 and VESA 100 Mounting Retention Screw Holes

Step 4: Secure the POC-17C-ULT3 to the interface pad by inserting four retention screws through the mounting arm interface pad and into the POC-17C-ULT3.

Page 43


Figure 3-32: Arm Mounting

3.12.3 Stand Mounting

To mount the POC-17C-ULT3 using the stand mounting kit, please follow the steps below.

Step 1: Locate the VESA mounting screw holes on the rear of the POC-17C-ULT3

(

Figure 3-31 ). This is where the bracket will be attached.

Step 2: Align the bracket of the stand with the screw holes.

Step 3: To secure the bracket to the POC-17C-ULT3, insert the retention screws into the screw holes and tighten them.

NOTE:

If the EZ stand (MEDP-EZS-R10) is mounted, the handle

(MEDP-HD-R10 or MEDP-HD-BR-R10) can not be installed.

Page 44


3.13 Powering On the System

WARNING:

To avoid risk of electric shock, this equipment must only be connected to supply mains with protective earth.

CAUTION:

The FSP PMP120-13-2 power adapter came with the POC-17C-ULT3 is a forming part of the medical device.

To power on the system, follow the steps below:

Step 1: Connect the power cord to the power adapter. Connect the other end of the power cord to a power source.

Step 2: Connect the power adapter to the power connector of the POC-17C-ULT3.

Step 3: Locate the power button on the rear panel.

Step 4: Short press the power button to turn on the POC-17C-ULT3.

The user can also long-press the touch buttons on the front panel

for three seconds to power on the system (please refer to Table 1-2

). Step 0:

Figure 3-33: Powering On the System

Page 45


3.14 Reset the System

The reset button enables user to reboot the system when the system is turned on. The reset button location is shown in

Figure 3-34 . Press the reset button to reboot the system.

Figure 3-34: Reset Button Location

Page 46


Chapter

4

4

BIOS Setup

Page 47


4.1 Introduction

The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed.

4.1.1 Starting Setup

The UEFI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. the key as soon as the system is turned on or the key when the “ Press DEL to enter SETUP ” message appears on the screen. 0.

If the message disappears before the DEL key is pressed, restart the computer and try again.

4.1.2 Using Setup

Use the arrow keys to highlight items, press E

NTER

to select, use the PageUp and

PageDown keys to change entries, press F1 for help and press E

SC

to quit. Navigation keys are shown in the following table.

Key Function

Up arrow Move to the item above

Down arrow Move to the item below

Left arrow Move to the item on the left hand side

Right arrow Move to the item on the right hand side

+ Increase the numeric value or make changes

Page 48

NOTE:

Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice.


-

F1 key

F2 key

F3 key

F4 key

Esc key

Decrease the numeric value or make changes

General help, only for Status Page Setup Menu and Option

Page Setup Menu

Load previous values.

Load optimized defaults

Save changes and Exit BIOS

Main Menu – Quit and do not save changes into CMOS

Status Page Setup Menu and Option Page Setup Menu --

Exit current page and return to Main Menu

Table 4-1: BIOS Navigation Keys

4.1.3 Getting Help

When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press E SC

or the F1 key again.

4.1.4 BIOS Menu Bar

The menu bar on top of the BIOS screen has the following main items:

Main – Changes the basic system configuration.

Advanced – Changes the advanced system settings.

Chipset – Changes the chipset settings.

Security – Sets User and Supervisor Passwords.

Boot – Changes the system boot configuration.

Save & Exit – Selects exit options and loads default settings

The following sections completely describe the configuration options found in the menu items at the top of the BIOS screen and listed above.

Page 49


4.2 Main

The Main

BIOS menu ( BIOS Menu 1 ) appears when the

BIOS Setup program is entered.

The Main menu gives an overview of the basic system information.

Aptio Setup Utility – Copyright (C) 2017 American Megatrends, Inc.

Main Advanced Chipset Security Boot Save & Exit

BIOS Information

BIOS Vendor

Core Version

Compliancy

Project Version

American Megatrends

5.11

UEFI 2.4; PI 1.3

E422AR10.ROM

Set the Date. Use Tab to switch between Date elements.

Build Date and Time 05/02/2017 14:37:58

Processor Information

Name

Brand String

Skylake

Intel(R) Core(TM) i7-6600U CPU @ 2.60GHz

MHz

----------------------

406E3 Processor ID

Stepping D0/K0

ÆÅ

: Select Screen

Number of Processors 2Core(S)/4Thread(s)

↑ ↓

: Select Item

Microcode Revision 7c

Enter: Select

GT Info GT2

+/-: Change Opt.

IGF VBIOS Version 1040

Memory RC Version

Total Memory

Memory Frequency

PCH Information

1.9.0.0

4096 MB

2133 MHz

Name

PCH SKU

LynxPoint

PCH-LP Mobile(U)

Stepping 21/C1

N/A LAN PHY Revision

ME FW Version

ME Firmware SKU

SPI Clock Frequency

11.0.0.1202

Corporate SKU

F4: Save & Exit

ESC: Exit

D0FR Support Unsupported

Read Status Clock Frequency 17 MHz

Write Status Clock Frequency 17 MHz

Fast Read Status Clock Frequency 17 MHz

System Date [Thu 07/06/2017]

System Time [16:49:37]

Access Level Administrator

Version 2.17.1255. Copyright (C) 2017 American Megatrends, Inc.

BIOS Menu 1: Main

Page 50


Î System Date [xx/xx/xx]

Use the System Date option to set the system date. Manually enter the day, month and year.

Î System Time [xx:xx:xx]

Use the System Time option to set the system time. Manually enter the hours, minutes and seconds.

4.3 Advanced

Use the Advanced

menu ( BIOS Menu 2

) to configure the CPU and peripheral devices through the following sub-menus:

WARNING:

Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware.

> Trusted Computing

> ACPI Settings

> F81866 Super IO Configuration

> F81866 H/M Monitor

> RTC Wake Settings

> Serial Port Console Redirection

> CPU Configuration

> SATA Configuration

> USB Configuration

> iEi Feature



Trusted Computing

Settings

----------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 2: Advanced

Page 51


4.3.1 Trusted Computing

Use the Trusted Computing


) to configure settings related to the

Trusted Computing Group (TCG) Trusted Platform Module (TPM).


Advanced

Configuration

Security Device Support

NO Security Device Found

[Enable]

Enables or Disables BIOS support for security device. O.S. will not show Security Device.

TCG EFI protocol and

INT1A interface will not be available.

----------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 3: Trusted Computing

Î Security Device Support [Enable]

Use the Security Device Support option to configure support for the security devices.

Î

Disable Security device support is disabled.

Î

Enable D EFAULT

Security device support is enabled.

Page 52


4.3.2 ACPI Settings

The ACPI Settings

menu ( BIOS Menu 4 ) configures the Advanced Configuration and

Power Interface (ACPI) options.


Advanced

ACPI Settings

ACPI Sleep State [S3 (Suspend to RAM)]

Select ACPI sleep state the system will enter when the SUSPEND button is pressed.

----------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 4: ACPI Settings

Î ACPI Sleep State [S3 (Suspend to RAM)]

Use the ACPI Sleep State option to specify the sleep state the system enters when it is not being used.

Î

S3 (Suspend to

RAM)

D EFAULT

The caches are flushed and the CPU is powered off. Power to the RAM is maintained. The computer returns slower to a working state, but more power is saved.

Page 53


4.3.3 F81866 Super IO Configuration

Use the F81866 Super IO Configuration

menu ( BIOS Menu 5 ) to set or change the

configurations for the serial ports.


Advanced

F81866 Super IO Configuration

Super IO Chip

> Serial Port 1 Configuration

> Serial Port 2 Configuration

F81866

Set Parameters of Serial

Port 1 (COMA)

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 5: F81866 Super IO Configuration

4.3.3.1 Serial Port n Configuration

Use the Serial Port n Configuration

menu ( BIOS Menu 6 ) to configure the serial port n.


Advanced

Serial Port 1 Configuration

Serial Port

Device Settings

Change Settings

[Enabled]

IO=3F8h; IRQ=4

[Auto]

Enable or Disable Serial

Port (COM)

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 6: Serial Port n Configuration Menu

Page 54


4.3.3.1.1 Serial Port 1 Configuration

Î Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.

Î

Disabled

Î

Enabled D EFAULT

Disable the serial port

Enable the serial port

Î Change Settings [Auto]

Use the Change Settings option to change the serial port IO port address and interrupt address.

Î

Auto D EFAULT

The serial port IO port address and interrupt address are automatically detected.

Î

IO=3F8h; IRQ=4 Serial Port I/O port address is 3F8h and the interrupt address is IRQ4

Î

IO=3F8h;

IRQ=3, 4, 5, 6, 7,

9, 10, 11, 12

Serial Port I/O port address is 3F8h and the interrupt address is IRQ3, 4, 5, 6, 7, 9, 10, 11,

12

Î

IO=2F8h;

IRQ=3, 4, 5, 6, 7,

9, 10, 11, 12


12

Î

IO=3E8h;

IRQ=3, 4, 5, 6, 7,

9, 10, 11, 12

Serial Port I/O port address is 3E8h and the interrupt address is IRQ3, 4, 5, 6, 7, 9, 10, 11,

12

Î

IO=2E8h;

IRQ=3, 4, 5, 6, 7,

9, 10, 11, 12


12

Î Device Mode [RS232]

Use the Device Mode option to set the Serial Port 1 signaling mode.

Page 55


Î

RS422

Î

RS232 D EFAULT

Î

RS485

Configure Serial Port 1 as RS-422



4.3.3.1.2 Serial Port 2 Configuration

Î Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.

Î

Disabled

Î


Disable the serial port

Enable the serial port

Î Change Settings [Auto]

Use the Change Settings option to change the serial port IO port address and interrupt address.

Î

Auto D EFAULT

The serial port IO port address and interrupt address are automatically detected.

Î

IO=2F8h; IRQ=3 Serial Port I/O port address is 2F8h and the interrupt address is IRQ3

Î

IO=3F8h;

IRQ=3, 4, 5, 6, 7,

9, 10, 11, 12


12

Î

IO=2F8h;

IRQ=3, 4, 5, 6, 7,

9, 10, 11, 12


12

Î

IO=3E8h;

IRQ=3, 4, 5, 6, 7,

9, 10, 11, 12


12

Î

IO=2E8h;

IRQ=3, 4, 5, 6, 7,

9, 10, 11, 12


12

Page 56


4.3.4 F81866 H/W Monitor

The F81866 H/W Monitor

menu ( BIOS Menu 7 ) shows the operating temperatures and

voltages.


Advanced

PC Health Status Smart Fan Mode Select

>Smart Fan Mode Configuration

CPU temperature

System temperature

: +51 ° C

: +49 ° C

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

CPU_CORE

Enter: Select

+5V

+/-: Change Opt.

+12V :

+DDR :

+3.3V :

+3.3VSB

F4: Save & Exit

+5VSB

ESC: Exit


BIOS Menu 7: F81866 H/W Monitor

Î PC Health Status

The following system parameters and values are shown. The system parameters that are monitored are:

Temperature: o CPU Temperature o System Temperature

Voltages: o CPU_CORE o +5V o +12V o +DDR o +3.3V o +3.3VSB o +5VSB

Page 57


4.3.5 RTC Wake Settings

The RTC Wake Settings

menu ( BIOS Menu 8 ) configures RTC wake event.


Advanced

Wake system with Fixed Time [Disabled] Enable or disable System wake on alarm event. When enabled, System will wake on the dat::hr::min::sec specified

----------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 8: RTC Wake Settings

Î Wake System with Fixed Time [Disabled]

Use the Wake System with Fixed Time option to specify the time the system should be roused from a suspended state.

Î

Disabled D

EFAULT

The real time clock (RTC) cannot generate a wake event

Page 58


Î

Enabled If selected, the following appears with values that can be selected:

*Wake up every day

*Wake up date

*Wake up hour

*Wake up minute

*Wake up second

After setting the alarm, the computer turns itself on from a suspend state when the alarm goes off.

4.3.6 Serial Port Console Redirection

The Serial Port Console Redirection menu (

BIOS Menu 9

) allows the console redirection options to be configured. Console redirection allows users to maintain a system remotely by re-directing keyboard input and text output through the serial port.


Advanced

COM1

Console Redirection

> Console Redirection Settings

[Disabled]

COM2

Console Redirection

> Console Redirection Settings

[Disabled]

Legacy Console Redirection

> Legacy Console Redirection Settings

Console Redirection

Enable or Disable.

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 9: Serial Port Console Redirection

Page 59


Î Console Redirection [Disabled]

Use Console Redirection option to enable or disable the console redirection function.

Î

Disabled D EFAULT

Î

Enabled

Disabled the console redirection function

Enabled the console redirection function

4.3.6.1 Console Redirection Settings

Use the Console Redirection Settings menu (

BIOS Menu 10 ) to configure console redirection settings of the specified serial port. This menu appears only when the

Console

Redirection option is enabled.


Advanced

COM1

Console Redirection Settings

Terminal Type

Bits per second

Data Bits

[ANSI]

[115200]

[8]

Emulation: ANSI: Extended

ASCII char set. VT100:

ASCII char set. VT100+:

Extends VT100 to support color, function keys, etc.

VT-UTF8: Uses UTF8

Stop Bits [1] chars onto 1 or more bytes.

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 10: Console Redirection Settings

Î Terminal Type [ANSI]

Use the Terminal Type option to specify the remote terminal type.

Î

VT100

Î

VT100+

The target terminal type is VT100

The target terminal type is VT100+

Page 60


Î

VT-UTF8

Î

ANSI D EFAULT

The target terminal type is VT-UTF8

The target terminal type is ANSI

Î Bits per second [115200]

Use the Bits per second option to specify the serial port transmission speed. The speed must match the other side. Long or noisy lines may require lower speeds.

Î

9600

Î

19200

Î

57600

Î

115200 D EFAULT

Sets the serial port transmission speed at 9600.




Î Data Bits [8]

Use the Data Bits option to specify the number of data bits.

Î

7 Sets the data bits at 7.

Î

8 D EFAULT

Sets the data bits at 8.

Î Parity [None]

Use the Parity option to specify the parity bit that can be sent with the data bits for detecting the transmission errors.

Î

None D EFAULT

Î

Even

Î

Î

Î

Odd

Mark

Space

No parity bit is sent with the data bits.

The parity bit is 0 if the number of ones in the data bits is even.

The parity bit is 0 if the number of ones in the data bits is odd.

The parity bit is always 1. This option does not provide error detection.

The parity bit is always 0. This option does not provide error detection.

Page 61


Î Stop Bits [1]

Use the Stop Bits option to specify the number of stop bits used to indicate the end of a serial data packet. Communication with slow devices may require more than 1 stop bit.

Î

1 D EFAULT

Î

Sets the number of stop bits at 1.

2

Sets the number of stop bits at 2.

4.3.6.2 Legacy Console Redirection Settings

The Legacy Console Redirection Settings menu (

BIOS Menu 11 ) allows the legacy

console redirection options to be configured.


Advanced

Legacy Serial Redirection Port [COM1] Select a COM port to display redirection of

Legacy OS and Legacy

OPROM Messages

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 11: Legacy Console Redirection Settings

Î Legacy Serial Redirection Port [COM1]

Use the Legacy Serial Redirection Port option to specify a COM port to display redirection of legacy OS and legacy OPROM messages. The options include:

COM1

COM2

D EFAULT

COM3 (Pci Bus0, Dev0, Func0) (Disabled)

Page 62


4.3.7 CPU Configuration

Use the CPU Configuration

( BIOS Menu 12 ) to view detailed CPU specifications and

configure the CPU.


Advanced

CPU Configuration

Intel(R) Core(TM) i7-6600U CPU @ 2.60GHz

CPU Signature

Microcode Patch

Max CPU Speed

Min CPU Speed

406E3

7C

2600 MHz

400 MHz

CPU Speed

Processor Cores

Hyper Threading Technology

Intel VT-x Technology

Intel SMX Technology

2500 MHz

2

Supported

Supported

Supported

Enable for Windows XP and

Linux (OS optimized for

Hyper-Threading

Technology) and Disabled for other OS (OS not optimized for

Hyper-Threading

Technology). When

Disabled only one thread per enabled core is enabled.

EIST Technology

L1 Data Cache

Supported

32 kB x 2

32 kB x 2

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

L1 Code Cache

L2 Cache

+/-: Change Opt.

256 kB x 2

L3 Cache 4 MB

F3: Optimized

Hyper-threading [Enabled]

Defaults

F4: Save & Exit

Active Processor Cores [All]

ESC: Exit

Intel Virtualization Technology [Disabled]

Intel(R) SpeedStep(tm) [Enabled]

CPU C states [Disabled]


BIOS Menu 12: CPU Configuration

The CPU Configuration menu lists the following CPU details:

Processor Type: Lists the brand name of the CPU being used

CPU Signature: Lists the CPU signature value.

Microcode Patch: Lists the microcode patch being used.

Max CPU Speed: Lists the maximum CPU processing speed.

Min CPU Speed: Lists the minimum CPU processing speed.

CPU Speed: Lists the CPU processing speed.

Processor Cores: Lists the number of the processor core

Hyper Threading Technology: Indicates if Intel HT Technology is supported by the CPU.

Page 63


Intel VT-x Technology: Indicates if Intel VT-x Technology is supported by the

CPU.

Intel SMX Technology: Indicates if Intel SMX Technology is supported by the

CPU.

64-bit: Indicates if 64-bit OS is supported by the CPU.

EIST Technology: Indicates if EIST Technology is supported by the CPU.

L1 Data Cache: Lists the amount of data storage space on the L1 cache.

L1 Code Cache: Lists the amount of code storage space on the L1 cache.

L2 Cache: Lists the amount of storage space on the L2 cache.

L3 Cache: Lists the amount of storage space on the L3 cache.

Î Hyper-threading [Enabled]

Use the Hyper-threading option to enable or disable the Intel® Hyper-Threading

Technology.

Î

Disabled

Disable Intel® Hyper-Threading Technology

Î


Enable Intel® Hyper-Threading Technology

Î Active Processor Cores [All]

Use the Active Processor Cores BIOS option to enable numbers of cores in the processor package.

Î

All

Î

D EFAULT

Enable all cores in the processor package.

Î Intel Virtualization Technology [Disabled]

Use the Intel Virtualization Technology option to enable or disable virtualization on the system. When combined with third party software, Intel® Virtualization technology allows several OSs to run on the same system at the same time.

Î


Disables Intel Virtualization Technology.

Î

Enabled Enables Intel Virtualization Technology.

Page 64


Î Intel

®

SpeedStep(tm) [Enabled]

Use the Intel

®

SpeedStep™ option to enable or disable the Intel ® SpeedStep

Technology.

Î

Disabled

Î


Disables the Intel ® SpeedStep Technology.

Enables the Intel ® SpeedStep Technology.

Î CPU C State [Disabled]

Use the CPU C State option to enable or disable CPU C state.

Î


Î

Enabled

Disables CPU C state.

Enables CPU C state.

4.3.8 SATA Configuration

Use the SATA Configuration


) to change and/or set the configuration of the SATA devices installed in the system.


Advanced

SATA Controller(s)

SATA Mode Selection

[Enabled]

[AHCI]

Enable/Disable SATA

Device.

---------------------

Hot Plug

SATA2

Hot Plug

[Disabled]

Empty

[Disabled]

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

Hot Plug [Disabled]

F4: Save & Exit

ESC: Exit


BIOS Menu 13: SATA Configuration

Page 65


Î SATA Controller(s) [Enabled]

Use the SATA Controller(s) option to configure the SATA controller(s).

Î


Enable the on-board SATA controller(s).

Î

Disabled

Disable the on-board SATA controller(s).

Î SATA Mode Selection [AHCI]

Use the SATA Mode Selection option to determine how SATA devices operate.

Î

AHCI

Î

RAID

D EFAULT

Configures SATA devices as AHCI device.

Configures SATA devices as RAID device.

NOTE:

Before accessing the RAID configuration utility, ensure to set the

Option ROM Messages BIOS option in the Boot menu to Force

BIOS . This is to allow the “Press <CTRL+I> to enter Configuration

Utility……” message to appear during POST. Press Ctrl+I when prompted to enter the RAID configuration utility.

NOTE:

1. For the Windows 7 user, please install the Intel® RAID driver included in the driver CD.

2. In case of the need of RAID surveillance function, please complete the .Net Framework 4.5 installation and download the Intel® RAID management software from the Intel® website: https://downloadcenter.intel.com/zh-tw/product/55005/Intel-Intel-RST.

Page 66


Î Hot Plug [Disabled]

Use the Hot Plug option to enable or disable the SATA device hot plug.

Î


Disables the SATA device hot plug.

Î

Enabled

Enables the SATA device hot plug

4.3.9 USB Configuration

Use the USB Configuration menu (

BIOS Menu 14 ) to read USB configuration

information and configure the USB settings.


Advanced

USB Configuration

USB Controllers:

1 XHCI

USB Devices:

1 Keyboard, 1 Mouse, 1 Point, 2 Hubs

Legacy USB Support [Enabled]

Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 14: USB Configuration

Î USB Devices

The USB Devices Enabled field lists the USB devices that are enabled on the system

Î Legacy USB Support [Enabled]

Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support. Normally if this option is not enabled, any attached USB mouse or USB keyboard

Page 67

POC-17C-ULT3 Medical Panel PC does not become available until a USB compatible operating system is fully booted with all

USB drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard can control the system even when there is no USB driver loaded onto the system.

Î


Î

Disabled

Î

Auto

Legacy USB support enabled

Legacy USB support disabled

Legacy USB support disabled if no USB devices are connected

4.3.10 IEI Feature

Use the IEI Feature


) to configure One Key Recovery function.


Advanced iEi Feature

Auto Recovery Function [Disabled]

Auto Recovery Function

Reboot and recover system automatically within 10 min, when OS crashes. Please install

Auto Recovery API service before enabling this funciton.

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 15: IEI Feature

Î Auto Recovery Function [Disabled]

Use the Auto Recovery Function BIOS option to enable or disable the auto recovery function of the IEI One Key Recovery.

Page 68


Î


Î

Enabled

Auto recovery function disabled

Auto recovery function enabled

4.4 Chipset

Use the Chipset menu (

BIOS Menu 16

) to configure the system chipset.



> System Agent (SA) Configuration

> PCH-IO Configuration

System Agent (SA)

Parameters

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 16: Chipset

Page 69


4.4.1 System Agent (SA) Configuration

Use the System Agent (SA) Configuration menu (

BIOS Menu 17 ) to configure the

System Agent (SA) parameters.


Chipset

VT-d

> Graphics Configuration

> Memory Configuration

[Disabled] VT-d capability

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 17: System Agent (SA) Configuration

Î VT-d [Disabled]

Use the VT-d option to enable or disable VT-d support.

Î


Disable VT-d support.

Î

Enabled Enable VT-d support.

Page 70


4.4.1.1 Graphics Configuration

Use the Graphics Configuration menu (

BIOS Menu 18 ) to configure the graphics

settings.

Graphics Configuration

Primary Display

Internal Graphics

DVMT Pre-Allocated

DVMT Total Gfx Mem

> LCD Control


Chipset

[Auto]

[Enabled]

[256M]

[MAX]

Select which of IGFX/PCIE

Graphics device should be

Primary Display.

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 18: Graphics Configuration

Î Primary Display [Auto]

Use the Primary Display option to select the graphics controller used as the primary boot device. Configuration options are listed below:

Auto

IGFX

PCIE

D EFAULT

Î Internal Graphics [Enabled]

Use the Internal Graphics option to enable or disable the internal graphics device.

Î

Auto

Î

Disabled

The internal graphics device is automatically detected and enabled.

Disable the internal graphics device.

Page 71


Î


Enable the internal graphics device. The following options/submenu appear with values that can be selected:

Total Mem

Î DVMT Pre-Allocated [256M]

Use the DVMT Pre-Allocated option to set the amount of system memory allocated to the integrated graphics processor when the system boots. The system memory allocated can then only be used as graphics memory, and is no longer available to applications or the operating system. Configuration options are listed below:

32M

64M

128M

256M

512M

D

EFAULT

Î DVMT Total Gfx Mem [MAX]

Use the DVMT Total Gfx Mem option to select DVMT5.0 total graphic memory size used by the internal graphic device. The following options are available:

128M

256M

 MAX D EFAULT

Page 72


4.4.1.1.1 LCD Control

Use the LCD Control submenu (

BIOS Menu 19 ) to select a display device which will be

activated during POST.


Chipset

LCD Control

Primary IGFX Boot Display [VBIOS Default]

Select the Video Device which will be activated during POST. This has no effect if external graphics present.

Secondary boot display selection will appear based on your selection.

VGA modes will be supported only on primary display.

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 19: LCD Control

Î Primary IGFX Boot Display [VBIOS Default]

Use the Primary IGFX Boot Display option to select the display device used by the system when it boots.

VBIOS

HDMI

LVDS

D EFAULT

Page 73


4.4.1.2 Memory Configuration

Use the Memory Configuration submenu ( BIOS Menu 20 ) to display the memory information.


Chipset

Memory Information

Total Memory

DIMM1

DIMM2

4096 MB

Not Present

4096 MB

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 20: Memory Configuration

4.4.2 PCH-IO Configuration

Use the PCH-IO Configuration menu (

BIOS Menu 21

) to configure the PCH-IO chipset.


Chipset

Auto Power Button Status

> PCI Express Configuration

> HD Audio Configuration

[Disable (ATX)] Select AC power state when power is re-applied after a power failure.

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 21: PCH-IO Configuration

Page 74


4.4.2.1 PCI Express Configuration

Use the PCI Express Configuration

submenu ( BIOS Menu 22

) to configure the PCI

Express slots.


Chipset

PCI Express Configuration

> M_PCIE1

> M2_CN1

M_PCIE1 Settings.

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 22: PCI Express Configuration

The M_PCIE1 and M2_CN1 submenus both contain the following options:

Î PCIe Speed [Auto]

Use the PCIe Speed option to configure the PCIe interface speed.

Auto

Gen

Gen

Gen

D EFAULT

Î Detect Non-Compliance Device [Disabled]

Use the Detect Non-Compliance Device option to enable or disable detecting if a non-compliance PCI Express device is connected to the PCI Express slot.

Page 75


Î


Disables to detect if a non-compliance PCI

Express device is connected to the PCI Express slot.

Î

Enabled Enables to detect if a non-compliance PCI Express device is connected to the PCI Express slot.

4.4.2.2 HD Audio Configuration

Use the HD Audio Configuration

submenu ( BIOS Menu 23

) to configure the High

Definition Audio codec.


Chipset

HD Audio Configuration

HD Audio [Enabled]

Control Detection of the

HD-Audio device.

Disable = HDA will be unconditionally disabled

Enabled = HDA will be unconditionally enabled.

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 23: HD Audio Configuration

Î HD Audio [Enabled]

Use the HD Audio BIOS option to enable or disable the High Definition Audio controller.

Î

Disabled

Î

The High Definition Audio controller is disabled.


The High Definition Audio controller is enabled.

Page 76


4.5 Security

Use the Security menu (

BIOS Menu 24 ) to set system and user passwords.



Password Description

If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup.

If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights.

The password must be

In the following range:

Maximum length

Minimum length

Administrator Password

3

20

Set Administrator

Password

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

User Password

F4: Save & Exit

ESC: Exit


BIOS Menu 24: Security

Î Administrator Password

Use the Administrator Password field to set or change an administrator password.

Î User Password

Use the User Password field to set or change a user password.

Page 77


4.6 Boot

Use the Boot menu (

BIOS Menu 25 ) to configure system boot options.

Boot Configuration

Bootup NumLock State

Quiet Boot

UEFI Boot

Launch PXE OpROM

Option ROM Messages

Boot Option Priorities



[On]

[Enabled]

[Disabled]

[Disabled]

[Force BIOS]

Select the keyboard

NumLock state

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 25: Boot

Î Bootup NumLock State [On]

Use the Bootup NumLock State BIOS option to specify if the number lock setting must be modified during boot up.

Î

On D EFAULT

Allows the Number Lock on the keyboard to be enabled automatically when the computer system boots up. This allows the immediate use of the

10-key numeric keypad located on the right side of the keyboard. To confirm this, the Number Lock LED light on the keyboard is lit.

Î

Off Does not enable the keyboard Number Lock automatically. To use the 10-keys on the keyboard, press the Number Lock key located on the upper left-hand corner of the 10-key pad. The Number

Lock LED on the keyboard lights up when the

Number Lock is engaged.

Page 78


Î Quiet Boot [Enabled]

Use the Quiet Boot BIOS option to select the screen display when the system boots.

Î

Disabled

Î


Normal POST messages displayed

OEM Logo displayed instead of POST messages

Î UEFI Boot [Disabled]

Use the UEFI Boot BIOS option to enable or disable UEFI boot.

Î


Î

Enabled

Disable UEFI boot.

Enable UEFI boot if the 1 st

boot device is a GPT

HDD.

Î Launch PXE OpROM [Disabled]

Use the Launch PXE OpROM option to enable or disable boot option for legacy network devices.

Î


Î

Enabled

Ignore all PXE Option ROMs

Load PXE Option ROMs

Î Option ROM Messages [Force BIOS]

Use the Option ROM Messages option to set the Option ROM display mode.

Î

Force

BIOS

Î

Keep

Current

D

EFAULT

Sets display mode to force BIOS.

Sets display mode to current.

Page 79


4.7 Save & Exit

Use the Save & Exit menu (

BIOS Menu 26 ) to load default BIOS values, optimal failsafe

values and to save configuration changes.

Restore Defaults

Save as User Defaults

Restore User Defaults



Save Changes and Reset

Discard Changes and Reset

Reset the system after saving the changes.

---------------------

ÆÅ

: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F4: Save & Exit

ESC: Exit


BIOS Menu 26: Save & Exit

Î Save Changes and Reset

Use the Save Changes and Reset option to save the changes made to the BIOS options and reset the system.

Î Discard Changes and Reset

Use the Discard Changes and Reset option to exit the system without saving the changes made to the BIOS configuration setup program.

Î Restore Defaults

Use the Restore Defaults option to load the optimal default values for each of the parameters on the Setup menus. F3 key can be used for this operation.

Page 80


Î Save as User Defaults

Use the Save as User Defaults option to save the changes done so far as user defaults.

Î Restore User Defaults

Use the Restore User Defaults option to restore the user defaults to all the setup options.

Page 81


Chapter

5

5

Driver Installation

Page 82


5.1 Available Software Drivers

NOTE:

The contents of the driver folder may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates.

All the drivers for the POC-17C-ULT3 are on the utility CD that came with the system. To install the drivers, please follow the steps below.

Step 1: Insert the CD into a CD drive connected to the system.

Step 2:

The driver main menu with a list of available drivers appears ( Figure 5-1 ).

Figure 5-1: Available Drivers

Step 3: Install all of the necessary drivers in this menu.

Step 0:

Page 83


5.2 Intel® Chipset Driver

To install the chipset driver, please follow the steps below.

Step 1: Select Chipset from the list of the driver CD.

Step 2: Double click the setup file in the folder. The Intel® Chipset Device Software installation wizard appears.

Figure 5-2: Intel® Chipset Device Software Installation Wizard

Step 3: Follow the step-by-step instruction of the installation wizard to install the driver.

Step 0:

Page 84


5.3 Intel® Graphics Driver

To install the graphics driver, please follow the steps below.

Step 1: Select VGA from the list of the driver CD. Locate the driver setup file for the corresponding operating system.

Step 2: Double click the setup file in the folder. The Intel® Graphics Driver installation wizard appears (

Figure 5-3 ).

Figure 5-3: Intel® Graphics Driver Installation Wizard

Step 3: Follow the step-by-step instruction of the installation wizard to install the graphics driver.

Step 0:

Page 85


5.4 Audio Driver

To install the driver for the speaker and the microphone, please follow the steps below.

Step 1: Select Audio from the list of the driver CD.

Step 2: Double click the setup file in the folder. The InstallShield Wizard screen

appears ( Figure 5-4 ).

Figure 5-4: Realtek HD Audio Driver InstallShield Wizard

Step 3: Follow the step-by-step instruction of the installation wizard to install the HD

Audio driver.

Step 0:

Page 86


5.5 LAN Driver

To install the LAN driver, please follow the steps below.

Step 1: Select LAN from the list of the driver CD. Locate the driver setup file for the corresponding operating system.

Step 2: Double click the setup file in the folder. The Install Wizard screen appears

(

Figure 5-4 ).

Figure 5-5: LAN Driver Installation Wizard

Step 3: Follow the step-by-step instruction of the installation wizard to install the Intel®

Network Connection driver.

Step 0:

Page 87


5.6 Intel® Management Engine

To install the Intel® Management Engine Components, please follow the steps below.

Step 1: Select ME from the list of the driver CD. Locate the driver setup file.

Step 2: Double click the setup file. The installation wizard window appears (

Figure 5-3 ).

Figure 5-6: Intel® ME Components Installation Wizard

Step 3: Follow the step-by-step instruction of the installation wizard to install the Intel®

Management Engine Components.

Step 0:

Page 88


5.7 Wireless LAN Driver

To install the wireless LAN driver, please follow the steps below.

Step 1: Select WIFI from the list of the driver CD. Locate the setup file from the WLAN folder.

Step 2: Double click the setup file in the folder, and then select the language for the installation. The InstallShield Wizard screen appears (

Figure 5-7

).

Figure 5-7: Wireless LAN InstallShield Wizard

Step 3: Follow the step-by-step instruction of the installation wizard to install the

Wireless LAN driver.

Step 0:

Page 89


5.8 Bluetooth Driver

To install the Bluetooth driver, please follow the steps below.

Step 1: Select WIFI from the list of the driver CD. Locate the setup file from the BT folder.

Step 2: Double click the setup file in the folder. The InstallShield Wizard screen appears

(

Figure 5-8

).

Figure 5-8: Bluetooth Driver InstallShield Wizard

Step 3: Follow the step-by-step instruction of the installation wizard to install the

Bluetooth driver.

Step 0:

Page 90


5.9 Keypad AP

The Keypad AP is an OSD control tool developed by IEI. To install the Keypad AP, please follow the steps below.

Step 1: Select Keypad AP from the list of the driver CD.

Step 2: Double click the setup file in the folder, and then select Yes from the dialog box.

The Setup Wizard screen appears ( Figure 5-9

).

Figure 5-9: Keypad AP Setup Wizard

Step 3: Follow the step-by-step instruction of the installation wizard to install the Keypad AP.

Step 4: After the installation, the Keypad AP can be accessed by pressing the brightness up/down buttons or the volume up/down buttons on the bottom frame of the monitor. It allows users to control screen brightness and audio volume.

Figure 5-10: Keypad AP

Page 91


5.10 RFID Driver (Optional)

To install the RFID driver, please follow the steps below.

Step 1: Open the Device Manager window. Long press or right click USB <-> Serial .

Select Update Driver Software from the pop-up window.

Figure 5-11: Device Manager - Update Driver Software

Step 2: The Update Driver Software window appears. Select Browse my computer for driver software .

Page 92


Figure 5-12: Update Driver Software Window

Step 3: The following window appears. Press/Click the Browse button to specify the

RFID driver directory (\Docs\12.Other\ POCP-MF-RFID-R10\RFID\D490). Then, press/click the Next button.

Figure 5-13: Browse for Driver Software Window

Step 4: The system starts installing the RFID driver.

Step 5: After the driver installation process is complete, a confirmation screen appears.

Click Close to exit the program.

Page 93


Figure 5-14: Driver Installation Complete Window

Step 6: Repeat Step 1 ~ Step 5 to install the RFID driver again.

Step 7: The Device Manager Window now shows the installed RFID devices.

Step 0:

Figure 5-15: Device Manager Window – RFID Devices

Page 94


5.11 3-in-1 Combo Reader Driver (Optional)

The drivers for the optional 3-in-1 combo reader are all located in the following folder of the driver CD: \Docs\12.Other\POCP-W22A-CR-R10 . Please follow the instructions below to install the drivers.

5.11.1 SCR Driver

Follow the steps below to install the SCR driver.

Step 1: Open the Device Manager window. Long press or right click Singular VCOM

Card Reader . Select Update Driver Software from the pop-up window.



Page 95




SCR driver directory (\Docs\12.Other\POCP-W22A-CR-R10\SCR). Then, press/click the Next button.


Page 96


Step 4:

The following window ( Figure 5-19

) appears as the driver is installed.

Figure 5-19: Installing Driver Window




Page 97


Step 6: The Device Manager Window now shows the installed SCR device.

Step 0:

Figure 5-21: Device Manager Window – SCR Device

Page 98


5.11.2 MSR Driver

Follow the steps below to install the MSR driver.

Step 1: Open the Device Manager window. Long press or right click Singular VCOM

Card Reader . Select Update Driver Software from the pop-up window.



Page 99




MSR driver directory (\Docs\12.Other\POCP-W22A-CR-R10\MSR). Then, press/click the Next button.


Page 100


Step 4:

The following window ( Figure 5-25

) appears as the driver is installed.

Figure 5-25: Installing Driver Window




Page 101


Step 6: The Device Manager Window now shows the installed MSR device.

Step 0:

Figure 5-27: Device Manager Window – MSR Device

5.11.3 Fingerprint Reader Driver

Follow the steps below to install the fingerprint reader driver.

Step 1: Select Other from the list of the driver CD.

Step 2:

The fingerprint reader driver is located in the following folder ( Figure 5-28

):

\Docs\12.Other\POCP-W22A-CR-R10\Finger Printer . Double click the setup.exe

file in this folder to install the driver.

Figure 5-28: Fingerprint Reader Driver Folder

Page 102


Step 3: The Egis ES603 WDM Driver welcome window appears.

Figure 5-29: Fingerprint Reader Driver InstallShield Wizard

Step 4: Follow the step-by-step instruction of the installation wizard to install the fingerprint reader driver.

Step 0:

Page 103


5.12 Barcode Reader Driver (Optional)

To install the barcode reader driver, please follow the steps below.

Step 1: Select Other from the list of the driver CD. Double click the Install_x86.bat

file

(or Install_x64.bat

for 64-bit OS) in the POCP-W22A-HD-BR-R10 folder shown in Figure 5-30 to install the barcode reader driver .

Figure 5-30: Barcode Reader Driver Folder

Step 2: The following window shows and starts installing the barcode reader driver.

When the installation is complete, the window will close automatically.

Figure 5-31: Barcode Reader Driver Installation

Page 104


Step 3: The Device Manager Window now shows the installed barcode reader device.

Step 0:

Figure 5-32: Device Manager Window – Barcode Reader Device

Page 105


Chapter

6

6

System Maintenance

Page 106


6.1 System Maintenance Introduction

If the components of the POC-17C-ULT3 fail they must be replaced. Please contact the system reseller or vendor to purchase the replacement parts.

6.2 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the maintenance of the



Electrostatic discharge (ESD) can cause serious damage to electronic components, including the POC-17C-ULT3. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the POC-17C-ULT3 is accessed internally, or any other electrical component is handled, the following anti-static precautions are strictly adhered to.

Wear an anti-static wristband : - Wearing a simple anti-static wristband can help to prevent ESD from damaging the board.

Self-grounding : - Before handling the board touch any grounded conducting material. During the time the board is handled, frequently touch any conducting materials that are connected to the ground.

Use an anti-static pad : - When configuring the POC-17C-ULT3, place it on an anti-static pad. This reduces the possibility of ESD damaging the

POC-17C-ULT3.

Only handle the edges of the PCB : - When handling the PCB, hold the PCB by the edges.

Page 107

6.3 Turn off the Power


WARNING:

Failing to turn off the system before opening it can cause permanent damage to the system and serious or fatal injury to the user.

Before any maintenance procedures are carried out on the system, make sure the system is turned off.

6.4 Removing the Covers

To access the POC-17C-ULT3 internally, the HDD cover, the plastic back cover and the internal aluminum cover must be removed. To remove the covers, please follow the steps below.

Step 1: Remove the three retention screws from the HDD cover ( Figure 6-1 ).

Figure 6-1: HDD Cover Retention Screws

Step 2: Lift the HDD cover off the POC-17C-ULT3.

Page 108


Step 3: Remove the six retention screws from the back cover ( Figure 6-2 ).

Figure 6-2: Back Cover Retention Screws

Step 4: Lift the back cover off the POC-17C-ULT3.

Step 5: Remove the 10 retention screws from the internal aluminum cover. ( Figure 6-3 ).

Figure 6-3: Aluminum Cover Retention Screws

Step 6: Lift the aluminum cover off the POC-17C-ULT3. Step 0:

Page 109


6.5 SO-DIMM Replacement

The POC-17C-ULT3 has two SO-DIMM slots, and is pre-installed with one 4 GB DDR4

SO-DIMM. To replace/install the SO-DIMM, please follow the instructions below.

Step 1: Remove the covers. See Section 6.4

.

Step 2: Locate the SO-DIMM slots ( Figure 6-4 ).

Figure 6-4: SO-DIMM Slot Locations

Step 3: To remove the SO-DIMM, push the two handles outwards. The memory module is ejected by a mechanism in the socket.

Step 4: Grasp the memory module by the edges and carefully pull it out of the socket.

Step 5: To install a new SO-DIMM, align the SO-DIMM so the notch on the memory module lines up with the notch on the memory socket ( Figure 6-5 ).

Step 6: Push the SO-DIMM into the socket at an angle ( Figure 6-5 ).

Step 7: Gently push downwards and the arms clip into place ( Figure 6-5 ).

Step 0:

Page 110


Figure 6-5: SO-DIMM Installation

6.6 PCIe Mini Card Installation

The POC-17C-ULT3 equips with a half-size PCIe Mini card slot that supports mSATA. To install a PCIe Mini card into the POC-17C-ULT3, please follow the steps below:

Step 1: Remove the covers. See Section 6.4

.

Step 2: Locate the PCIe Mini card slot ( M_PCIE1 ) on the motherboard. Remove the preinstalled retention screw on the screw pillar of the PCIe Mini slot ( Figure 6-6 ).

Figure 6-6: PCIe Mini Card Slot Location

Page 111


Step 3: Line up the notch on the PCIe Mini card with the notch on the connector. Slide the PCIe Mini card into the socket at an angle of about 20º ( Figure 6-7 ).

Step 4: Press the other end of the PCIe Mini card down and secure the card with the previously removed retention screw ( Figure 6-7 ).

Step 0:

Figure 6-7: PCIe Mini Card Installation

6.7 Reinstalling the Covers

WARNING:

Failing to reinstall the covers may result in permanent damage to the system. Please make sure all coverings are properly installed.

When maintenance procedures are complete, please make sure the internal aluminum cover, plastic back cover and HDD cover are replaced.

Page 112


Chapter

7

7

Interface Connectors

Page 113


7.1 Peripheral Interface Connectors

The POC-17C-ULT3 panel PC motherboard comes with a number of peripheral interface connectors and configuration jumpers. The connector locations are shown in Figure 7-1 .

The Pin 1 locations of the on-board connectors are also indicated in the diagram below.

The connector pinouts for these connectors are listed in the following sections.

Figure 7-1: Main Board Layout Diagram

Page 114


7.2 Internal Peripheral Connectors

Internal peripheral connectors are found on the motherboard and are only accessible when the motherboard is outside of the chassis. The table below shows a list of the peripheral interface connectors on the motherboard. Pinouts of these connectors can be found in the following sections.

Connector

Audio connector

Audio out connector

Battery connector

Clear CMOS button

Type

4-pin wafer

4-pin wafer

2-pin wafer

Push button

Label

AUDIO_OUT1

AMP_OUT1

BAT1

J_CMOS1

DDR4 SO-DIMM slots

260-pin DDR4

SO-DIMM slot

12-pin wafer Debug connector

Inverter connector

LVDS connector

6-pin wafer

40-pin crimp

M.2 slot (installed with WLAN module) M.2 A-E key slot

MCU connector 9-pin wafer

MCU flash connector

MCU flash SPI ROM connector

10-pin header

6-pin wafer

Microphone connector

PCIe Mini card slot (supports mSATA module)

DIMM4, DIMM5

DBG_PORT1

INVERTER1

LVDS1

M2_CN1

HOTKEY_CN1

JP8

MCU_SPI1

4-pin wafer DMIC1

Half-size PCIe Mini slot M_PCIE1

Power button connector

Power LED connector

RS-232 serial port connector

SATA connector

SPI flash connector

TPM connector

2-pin wafer

3-pin wafer

10-pin header

7-pin connector

6-pin wafer

20-pin crimp

PWR_BTN1

PW_LED1

COM2

SATA1, SATA2

JSPI1

TPM1

Page 115

Connector

USB connectors


Type

4-pin wafer

Label

BT_USB1

CAM_USB1

RFID_USB1

TOUCH_USB1

Table 7-1: Peripheral Interface Connectors

7.2.1 Audio Connector (AUDIO_OUT1)

PIN NO. DESCRIPTION

1 AMP_INL

2 OUT1L

3 OUT1R

4 AMP_INR

Table 7-2: Audio Connector (AUDIO_OUT1) Pinouts

7.2.2 Audio Out Connector (AMP_OUT1)

PIN NO. DESCRIPTION

1 SPK_OUT_P_L

2 SPK_OUT_N_L

3 SPK_OUT_N_R

4 SPK_OUT_P_R

Table 7-3: Audio Out Connector (AMP_OUT1) Pinouts

7.2.3 Battery Connector (BAT1)

PIN NO. DESCRIPTION

1 VBATT

2 GND

Table 7-4: Battery Connector (BAT1) Pinouts

Page 116


7.2.4 Debug Connector (DBG_PORT1)

PIN NO. DESCRIPTION

1 NC

3 GND

5 LPC_AD3

7 LPC_AD1

9 FRAME#

11 PLT_CLK

PIN NO. DESCRIPTION

2 +3.3S

4 INT_SERIRQ

6 LPC_AD2

8 LPC_AD0

10 PLT_RST#

12 GND

Table 7-5: Debug Connector (DBG_PORT1) Pinouts

7.2.5 Inverter Connector (INVERTER1)

PIN NO. DESCRIPTION

1 +12V

2 +12V

3 ENABKL

4 BRIGHTNESS

5 GND

6 GND

Table 7-6: Inverter Connector (INVERTER1) Pinouts

7.2.6 LVDS Connector (LVDS1)

PIN NO. DESCRIPTION

1 GND

3 A0M_L

5 A0P_L

7 GND

9 A2M_L

11 A2P_L

13 GND

PIN NO. DESCRIPTION

2 GND

4 A1M_L

6 A1P_L

8 GND

10 CLK1M_L

12 CLK1P_L

14 GND

Page 117


PIN NO. DESCRIPTION

15 A3M_L

17 A3P_L

19 GND

21 A5M_L

23 A5P_L

25 GND

27 CLK2M_L

29 CLK2P_L

31 GND

33 GND

35 PANEL_VCC

37 PANEL_VCC

39 PANEL_VCC

PIN NO. DESCRIPTION

16 A4M_L

18 A4P_L

20 GND

22 A6M_L

24 A6P_L

26 GND

28 A7M_L

30 A8P_L

32 GND

34 GND

36 PANEL_VCC

38 PANEL_VCC

40 PANEL_VCC

Table 7-7: LVDS Connector (LVDS1) Pinouts

7.2.7 MCU Connector (HOTKEY_CN1)

PIN NO. DESCRIPTION

1 +5V

2 AUTO_DIMMING

3 VOL+

4 VOL-

5 BRIGHT+

6 BRIGHT-

8 N/A

9 GND

Table 7-8: MCU Connector (HOTKEY_CN1) Pinouts

Page 118


7.2.8 MCU Flash Connector (JP8)

PIN NO. DESCRIPTION

1 MCLR

3 +5V

5 GND

7 ICSPCLK

9 ICSPDAT

PIN NO. DESCRIPTION

2 +3.3A

4 MCU_IR

6 AUTO_CLK

8 AUTO_DATA

10 GND

Table 7-9: MCU Flash Connector (JP8) Pinouts

7.2.9 MCU Flash SPI ROM Connector (MCU_SPI1)

PIN NO. DESCRIPTION

1 MCU2_MCLR

2 VCC_MCU2

3 GND

4 MCU2_ICSPCLK

5 MCU2_ICSPDAT

6 NC

Table 7-10: MCU Flash SPI ROM Connector (MCU_SPI1) Pinouts

7.2.10 Microphone Connector (DMIC1)

PIN NO. DESCRIPTION

1 DMIC_CLK

2 DMIC_DATA

3 +3.3V

4 GND

Table 7-11: Microphone Connector (DMIC1) Pinouts

Page 119


7.2.11 Power Button Connector (PWR_BTN1)

PIN NO. DESCRIPTION

1 PW_BN

2 GND

Table 7-12: Power Button Connector (PWR_BTN1) Pinouts

7.2.12 Power LED Connector (PW_LED1)

PIN NO. DESCRIPTION

2 GND

3 SUS PW LED +5V

Table 7-13: Power LED Connector (PW_LED1) Pinouts

7.2.13 RS-232 Serial Port Connector (COM2)

PIN NO. DESCRIPTION

1 -NDCD2

3 NSIN2

5 NSOUT2

7 -NDTR2

9 GND

PIN NO. DESCRIPTION

2 -NDSR2

4 -NRTS2

6 -NCTS2

8 -XRI2

10 N/C

Table 7-14: RS-232 Serial Port Connector (COM2) Pinouts

Page 120


7.2.14 SATA Connectors (SATA1 & SATA2)

PIN NO. DESCRIPTION

1 GND

2 TX+

3 TX-

4 GND

5 RX-

6 RX+

7 GND

Table 7-15: SATA Connectors (SATA1 & SATA2) Pinouts

7.2.15 SPI Flash Connector (JSPI1)

PIN NO. DESCRIPTION

1 +V3.3M_SPI_CON

2 SPI_CS#0_CN

3 SPI_SO_SW

4 SPI_CLK_SW

5 SPI_SI_SW

6 GND

Table 7-16: SPI Flash Connector (JSPI1) Pinouts

7.2.16 TPM Connector (TPM1)

PIN NO. DESCRIPTION

1 LCLK

3 LFRAME#

5 LRERST#

7 LAD3

9 +3V

11 LAD0

PIN NO. DESCRIPTION

2 GND

4 KEY

6 +5V

8 LAD2

10 LAD1

12 GND

Page 121


PIN NO. DESCRIPTION

13 SCL

15 SB3V

17 GND

19 LPCPD#

PIN NO. DESCRIPTION

14 SDA

16 SERIRQ

18 GLKRUN#

20 LDRQ#

Table 7-17: TPM Connector (TPM1) Pinouts

7.2.17 USB Connector (BT_USB1)

PIN NO. DESCRIPTION

1 +5A

2 HUB_D1F-

3 HUB_D1F+

4 GND

Table 7-18: USB Connector (BT_USB1) Pinouts

7.2.18 USB Connector (CAM_USB1)

PIN NO. DESCRIPTION

1 +5A

2 HUB_D2F-

3 HUB_D2F+

4 GND

Table 7-19: USB Connector (CAM_USB1) Pinouts

Page 122


7.2.19 USB Connector (RFID_USB1)

PIN NO. DESCRIPTION

1 +5A

2 HUB_D3F-

3 HUB_D3F+

4 GND

Table 7-20: USB Connector (RFID_USB1) Pinouts

7.2.20 USB Connector (TOUCH_USB1)

PIN NO. DESCRIPTION

1 +5A

2 D4F-

3 D4F+

4 GND

Table 7-21: USB Connector (TOUCH_USB1) Pinouts

7.3 External Interface Panel Connectors

The table below lists the rear panel connectors on the POC-17C-ULT3 panel PC motherboard. Pinouts of these connectors can be found in the following sections.

Connector

AT/ATX mode selection switch

Barcode reader connector

GbE connectors

HDMI output connector

Power connector

Reset button

RS-232/422/485 serial port

Type

Switch

RJ-11

RJ-45

HDMI connector

4-pin DIN

Push button

DB-9

Label

J_ATX_AT1

BAR_CN1

LAN1, LAN2

HDMI_OUT1

PWR1

RST1

COM1

Page 123


Connector

USB 2.0 connectors

USB 3.0 connectors

Table 7-22: Rear Panel Connectors

Type

USB 2.0 port

USB 3.0 port

Label

USB20_CN1

USB_CON1

USB_CON2

7.3.1 GbE Connectors (LAN1 & LAN2)

PIN NO. DESCRIPTION

1 MDI0+

2 MDI0-

3 MDI1+

4 MDI1-

5 N/A

6 N/A

7 MDI2+

8 MDI2-

9 MDI3+

PIN NO. DESCRIPTION

10 MDI3-

11 +3.3Vsus

12 ACT-1

15 GND

16 GND

17 N/A

18 N/A

Table 7-23: GbE Connectors (LAN1 & LAN2) Pinouts

7.3.2 HDMI Output Connector (HDMI_OUT1)

PIN NO. DESCRIPTION PIN NO. DESCRIPTION

2 GND 12 HDMI_CLK#

5 GND 15 HDMI_SCL

8 GND 18 +5VCC

Page 124


10 HDMI_CLK+

Table 7-24: HDMI Connector (HDMI1) Pinouts

7.3.3 Power Connector (PWR1)

Table 7-25: Power Connector (PWR1) Pinouts

7.3.4 RS-232/422/485 DB-9 Serial Port (COM1)

PIN NO. DESCRIPTION PIN NO. DESCRIPTION

1 NDCD1 6 NDSR1

2 NSIN1 7 NRTS1

3 NSOUT1 8 NCTS1

4 NDTR1

5 GND

9 XRI1

Table 7-26: RS-232/422/485 DB-9 Serial Port (COM1) Pinouts

7.3.5 USB 2.0 Connectors (USB20_CN1)

PIN NO. DESCRIPTION

1 +5A

3 D8F-

5 D8F+

7 GND

PIN NO. DESCRIPTION

2 GND

4 D9F+

6 D9F-

8 +5A

Table 7-27: USB 2.0 Connector (USB20_CN1) Pinouts

Page 125


7.3.6 USB 3.0 Connectors (USB_CON1)

PIN NO. DESCRIPTION

1 +5A

2 2.0_D0-

3 2.0_D0+

4 GND

5 3.0_RX0-

6 3.0_RX0+

7 GND

8 3.0_TX0-

9 3.0_TX0+

PIN NO. DESCRIPTION

10 +5A

11 2.0_D1-

12 2.0_D1+

13 GND

14 3.0_RX1-

15 3.0_RX1+

16 GND

17 3.0_TX1-

18 3.0_TX1+

Table 7-28: USB 3.0 Connector (USB_CON12) Pinouts

7.3.7 USB 3.0 Connectors (USB_CON2)

PIN NO. DESCRIPTION

1 +5A

2 2.0_D2-

3 2.0_D2+

4 GND

5 3.0_RX2-

6 3.0_RX2+

7 GND

8 3.0_TX2-

9 3.0_TX2+

PIN NO. DESCRIPTION

10 +5A

11 2.0_D3-

12 2.0_D3+

13 GND

14 3.0_RX3-

15 3.0_RX3+

16 GND

17 3.0_TX3-

18 3.0_TX3+

Table 7-29: USB 3.0 Connector (USB_CON2) Pinouts

Page 126


7.4 Preconfigured Jumper Settings

CAUTION:

The following jumpers are preconfigured for the POC-17C-ULT3. Users should not change these jumpers ( Table 7-30 ).

Jumper Name

Flash descriptor security override

LVDS voltage selection

LVDS panel resolution selection

PCIe Mini/mSATA mode selection

Table 7-30: Preconfigured Jumpers

Type

2-pin header

6-pin header

Switch

Switch

Label

ME_FLASH1

J_VLVDS1

SW1

MSATA_CN1

7.4.1 Flash Descriptor Security Override Jumper (ME_FLASH1)

Pin Description

Short 1-2 Clear ME

Table 7-31: Flash Descriptor Security Override Jumper (ME_FLASH1) Settings

7.4.2 LVDS Panel Voltage Selection Jumper (J_VLVDS1)

Pin Description

Short 1-2

Short 3-4

Short 5-6

+3.3 V (Default)

+5 V

+12 V

Table 7-32: LVDS Voltage Selection Jumper (J_VLVDS1) Settings

Page 127


7.4.3 LVDS Panel Resolution Selection Jumper (SW1)

* ON=0, OFF=1; Single=S, Dual=D

SW1 (4-3-2-1) Description

0000

0001

800x600 18bit S (Default)

1024x768 18bit S

0010

0011

0100

0101

1024x768 24bit S

1280x768 18bit S

1280x800 18bit S

1280x960 18bit S

0111

1000

1001

1366x768 18bit S

1366x768 24bit S

1440x960 24bit D

1011 1600x900 24bit D

Table 7-33: LVDS Resolution Selection Jumper (SW1) Settings

7.4.4 PCIe Mini/mSATA Mode Selection (MSATA_CN1)

Pin Description

Short A-B

Short B-C mSATA (Default)

PCIe Mini

Table 7-34: PCIe Mini/mSATA Mode Selection (MSATA_CN1) Settings

Page 128


Appendix

A

A

Regulatory Compliance

Page 129


DECLARATION OF CONFORMITY

This equipment is in conformity with the following EU directives:

EMC Directive (2004/108/EC, 2014/30/EU)

Low-Voltage Directive (2006/95/EC, 2014/35/EU)

RoHS II Directive (2011/65/EU, 2015/863/EU)

Medical Device Directive 93/42/EEC: EN 60601-1

If the user modifies and/or install other devices in the equipment, the CE conformity declaration may no longer apply.

If this equipment has telecommunications functionality, it also complies with the requirements of the Radio Equipment Directive 2014/53/EU.

English

IEI Integration Corp declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.

Български [Bulgarian]

IEI Integration Corp. декларира , че този оборудване е в съответствие със съществените изисквания и другите приложими правила на Директива 2014/53/EU.

Č esky [Czech]

IEI Integration Corp tímto prohlašuje, že tento za ř ízení je ve shod ě se základními požadavky a dalšími p ř íslušnými ustanoveními sm ě rnice 2014/53/EU.

Dansk [Danish]

IEI Integration Corp erklærer herved, at følgende udstyr overholder de væsentlige krav og

øvrige relevante krav i direktiv 2014/53/EU.

Deutsch [German]

IEI Integration Corp, erklärt dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 2014/53/EU.

Eesti [Estonian]

IEI Integration Corp deklareerib seadme seadme vastavust direktiivi 2014/53/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

Page 130


Español [Spanish]

IEI Integration Corp declara que el equipo cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 2014/53/EU.

Ελληνική [Greek]

IEI Integration Corp ΔΗΛΩΝΕΙ ΟΤΙ ΕΞΟΠΛΙΣΜΟΣ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ

ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ

2014/53/EU.

Français [French]

IEI Integration Corp déclare que l'appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 2014/53/EU.

Italiano [Italian]

IEI Integration Corp dichiara che questo apparecchio è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 2014/53/EU.

Latviski [Latvian]

IEI Integration Corp deklar ē , ka iek ā rta atbilst b ū tiskaj ā m pras ī b ā m un citiem ar to saist ī tajiem noteikumiem Direkt ī vas 2014/53/EU.

Lietuvi ų [Lithuanian]

IEI Integration Corp deklaruoja, kad šis į ranga atitinka esminius reikalavimus ir kitas

2014/53/EU Direktyvos nuostatas.

Nederlands [Dutch]

IEI Integration Corp dat het toestel toestel in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 2014/53/EU.

Malti [Maltese]

IEI Integration Corp jiddikjara li dan prodott jikkonforma malħ ti ġ ijiet essenzjali u ma provvedimenti o ħ rajn relevanti li hemm fid-Dirrettiva 2014/53/EU.

Magyar [Hungarian]

IEI Integration Corp nyilatkozom, hogy a berendezés megfelel a vonatkozó alapvetõ követelményeknek és az 2014/53/EU irányelv egyéb elõírásainak.

Polski [Polish]

IEI Integration Corp o ś wiadcza, ż e wyrobu jest zgodny z zasadniczymi wymogami oraz pozosta ł ymi stosownymi postanowieniami Dyrektywy 2014/53/EU.

Português [Portuguese]

IEI Integration Corp declara que este equipamento está conforme com os requisitos essenciais e outras disposições da Directiva 2014/53/EU.

Page 131


Româna [Romanian]

IEI Integration Corp declar ă c ă acest echipament este in conformitate cu cerin ţ ele esen ţ iale ş i cu celelalte prevederi relevante ale Directivei 2014/53/EU.

Slovensko [Slovenian]

IEI Integration Corp izjavlja, da je ta opreme v skladu z bistvenimi zahtevami in ostalimi relevantnimi dolo č ili direktive 2014/53/EU.

Slovensky [Slovak]

IEI Integration Corp týmto vyhlasuje, že zariadenia sp ĺň a základné požiadavky a všetky príslušné ustanovenia Smernice 2014/53/EU.

Suomi [Finnish]

IEI Integration Corp vakuuttaa täten että laitteet on direktiivin 2014/53/EU oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Svenska [Swedish]

IEI Integration Corp förklarar att denna utrustningstyp står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv

2014/53/EU.

FCC WARNING

This equipment complies with part 18 of the FCC Rules.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Page 132


ROHS STATEMENT

The label on the product indicates this product conforms to European (EU) Restriction of

Hazardous Substances (RoHS) that set maximum concentration limits on hazardous materials used in electrical and electronic equipment.

CHINA ROHS

The label on the product indicates the estimated “Environmentally Friendly Use Period”

(EFUP). This is an estimate of the number of years that these substances would “not leak out or undergo abrupt change.” This product may contain replaceable sub-assemblies/components which have a shorter EFUP such as batteries and lamps.

These components will be separately marked.

Page 133


Appendix

B

B

Safety Precautions

Page 134


WARNING:

The precautions outlined in this chapter should be strictly followed.

Failure to follow these precautions may result in permanent damage to the POC-17C-ULT3.

B.1 Safety Precautions

Please follow the safety precautions outlined in the sections that follow:

B.1.1 General Safety Precautions

Please ensure the following safety precautions are adhered to at all times.

 To prevent the risk of electric shock, make sure power cord is unplugged from wall socket.

To fully disengage the power to the unit, please disconnect the power cord from the ac outlet. Refer servicing to qualified service personnel. The AC outlet shall be readily available and accessible.

 Users must not allow SIP/SOPs and the patient to come into contact at the same time.

Grounding reliability can only be achieved when the equipment is connected to an equivalent receptacle marked “Hospital Only” or “Hospital

Grade”.

Follow the electrostatic precautions outlined below whenever the

POC-17C-ULT3 is opened.

Make sure the power is turned off and the power cord is disconnected whenever the POC-17C-ULT3 is being installed, moved or modified.

Do not apply voltage levels that exceed the specified voltage range .

Doing so may cause fire and/or an electrical shock. Use a power cord that matches the voltage of the power outlet, which has been approved and complies with the safety standard of your particular country.

Page 135


Electric shocks can occur if the POC-17C-ULT3 chassis is opened when the POC-17C-ULT3 is running. To avoid risk of electric shock, this equipment must only be connected to a supply mains with protective earth.

Do not drop or insert any objects into the ventilation openings of the

POC-17C-ULT3.

 If considerable amounts of dust, water, or fluids enter the

POC-17C-ULT3 , turn off the power supply immediately, unplug the power cord, and contact the POC-17C-ULT3 vendor.

DO NOT : o Drop the POC-17C-ULT3 against a hard surface. o Strike or exert excessive force onto the LCD panel. o Touch any of the LCD panels with a sharp object o In a site where the ambient temperature exceeds the rated temperature

B.1.2 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the installation of the



Electrostatic discharge (ESD) can cause serious damage to electronic components, including the POC-17C-ULT3. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the POC-17C-ULT3 is opened and any of the electrical components are handled, the following anti-static precautions are strictly adhered to.

Wear an anti-static wristband : Wearing a simple anti-static wristband can help to prevent ESD from damaging any electrical component.

Self-grounding : Before handling any electrical component, touch any grounded conducting material. During the time the electrical component is handled, frequently touch any conducting materials that are connected to the ground.

Page 136


Use an anti-static pad : When configuring or working with an electrical component, place it on an anti-static pad. This reduces the possibility of ESD damage.

Only handle the edges of the electrical component : When handling the electrical component, hold the electrical component by its edges.

B.1.3 Product Disposal

CAUTION:

Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery.

Dispose of used batteries according to instructions and local regulations.

Outside the European Union - If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method.

Within the European Union – The device that produces less waste and is easier to recycle is classified as electronic device in terms of the European

Directive 2012/19/EU (WEEE), and must not be disposed of as domestic garbage.

EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. This includes monitors and electrical accessories, such as signal cables or power cords.

When you need to dispose of your display products, please follow the guidance of your local authority, or ask the shop where you purchased the product. The mark on electrical and electronic products only applies to the current European Union

Member States.

Please follow the national guidelines for electrical and electronic product disposal.

Page 137


B.1.4

Classification

Power by Class I power supply (IEI, POC-17C-ULT3)

No Part.

No protection against the ingress of water: IPX0

Mode of operation: Continuous Operation

The equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide: Not AP or APG Category.

B.2 Maintenance and Cleaning Precautions

When maintaining or cleaning the POC-17C-ULT3, please follow the guidelines below.

WARNING:

If you dropped any material or liquid such as water onto the panel PC when cleaning, unplug the power cable immediately and contact your dealer or the nearest service center. Always make sure your hands are dry when unplugging the power cable.

CAUTION:

For safety reasons, turn-off the power switch and unplug the panel

PC before cleaning.

Do not scratch or rub the screen with a hard object.

Never use any of the following solvents on the medical panel PC.

Harsh chemicals may cause damage to the cabinet and the touch sensor.

Thinner Spray-type cleaner, Benzene, Wax, Abrasive cleaner,

Acid or Alkaline solvent.

Page 138


B.2.1 Maintenance and Cleaning

Prior to cleaning any part or component of the POC-17C-ULT3, please read the details below.

To clean the POC-17C-ULT3, o remove dirt with a lightly moistened cloth. Then wipe the external chassis with a soft dry cloth. o use 75% ethanol alcohol to clean the external chassis.

Cleaning frequency: follow the cleaning method guidelines of the hospital.

Except for the LCD panel, never spray or squirt liquids directly onto any other components.

The interior of the POC-17C-ULT3 does not require cleaning. Keep fluids away from the POC-17C-ULT3 interior.

Never drop any objects or liquids through the openings of the

POC-17C-ULT3.

B.2.2 Cleaning Tools

Some components in the POC-17C-ULT3 may only be cleaned using a product specifically designed for the purpose. In such case, the product will be explicitly mentioned in the cleaning tips. Below is a list of items to use when cleaning the POC-17C-ULT3.

Cloth – Although paper towels or tissues can be used, a soft, clean piece of cloth is recommended when cleaning the POC-17C-ULT3.

Water/Ethanol alcohol – A cloth moistened with water or 75% ethanol alcohol can be used to clean the POC-17C-ULT3.

Using solvents – The use of solvents is not recommended when cleaning the

POC-17C-ULT3 as they may damage the plastic parts.

Cotton swabs - Cotton swaps moistened with water are excellent tools for wiping hard to reach areas.

Foam swabs - Whenever possible, it is best to use lint free swabs such as foam swabs for cleaning.

Page 139


Appendix

C

C

BIOS Menu Options

Page 140


　 System Date [xx/xx/xx] ........................................................................................................

51

　 System Time [xx:xx:xx] .......................................................................................................

51

　 Security Device Support [Enable] ......................................................................................

52

　 ACPI Sleep State [S3 (Suspend to RAM)]..........................................................................

53

　 Serial Port [Enabled]............................................................................................................

55

　 Change Settings [Auto] .......................................................................................................

55

　 Device Mode [RS232]...........................................................................................................

55

　 Serial Port [Enabled]............................................................................................................

56

　 Change Settings [Auto] .......................................................................................................

56

　 PC Health Status ..................................................................................................................

57

　 Wake System with Fixed Time [Disabled] .........................................................................

58

　 Console Redirection [Disabled] .........................................................................................

60

　 Terminal Type [ANSI]...........................................................................................................

60

　 Bits per second [115200].....................................................................................................

61

　 Data Bits [8] ..........................................................................................................................

61

　 Parity [None].........................................................................................................................

61

　 Stop Bits [1] ..........................................................................................................................

62

　 Legacy Serial Redirection Port [COM1].............................................................................

62

　 Hyper-threading [Enabled]..................................................................................................

64

　 Active Processor Cores [All] ..............................................................................................

64

　 Intel Virtualization Technology [Disabled] ........................................................................

64

　 Intel

®

SpeedStep(tm) [Enabled] ..........................................................................................

65

　 CPU C State [Disabled]........................................................................................................

65

　 SATA Controller(s) [Enabled] .............................................................................................

66

　 SATA Mode Selection [AHCI]..............................................................................................

66

　 Hot Plug [Disabled]..............................................................................................................

67

　 USB Devices .........................................................................................................................

67

　 Legacy USB Support [Enabled]..........................................................................................

67

　 Auto Recovery Function [Disabled]...................................................................................

68

　 VT-d [Disabled].....................................................................................................................

70

　 Primary Display [Auto] ........................................................................................................

71

　 Internal Graphics [Enabled] ................................................................................................

71

　 DVMT Pre-Allocated [256M] ................................................................................................

72

　 DVMT Total Gfx Mem [MAX]................................................................................................

72

Page 141


　 Primary IGFX Boot Display [VBIOS Default] .....................................................................

73

　 PCIe Speed [Auto]................................................................................................................

75

　 Detect Non-Compliance Device [Disabled] .......................................................................

75

　 HD Audio [Enabled] .............................................................................................................

76

　 Administrator Password .....................................................................................................

77

　 User Password .....................................................................................................................

77

　 Bootup NumLock State [On]...............................................................................................

78

　 Quiet Boot [Enabled] ...........................................................................................................

79

　 UEFI Boot [Disabled] ...........................................................................................................

79

　 Launch PXE OpROM [Disabled] .........................................................................................

79

　 Option ROM Messages [Force BIOS].................................................................................

79

　 Save Changes and Reset ....................................................................................................

80

　 Discard Changes and Reset ...............................................................................................

80

　 Restore Defaults ..................................................................................................................

80

　 Save as User Defaults .........................................................................................................

81

　 Restore User Defaults .........................................................................................................

81

Page 142


Appendix

D

D

Watchdog Timer

Page 143


NOTE:

The following discussion applies to DOS. Contact IEI support or visit the IEI website for drivers for other operating systems.

The Watchdog Timer is a hardware-based timer that attempts to restart the system when it stops working. The system may stop working because of external EMI or software bugs.

The Watchdog Timer ensures that standalone systems like ATMs will automatically attempt to restart in the case of system problems.

A BIOS function call (INT 15H) is used to control the Watchdog Timer.

INT 15H:

AH – 6FH Sub-function:

AL – 2: Sets the Watchdog Timer’s period.

BL: Time-out value (Its unit-second is dependent on the item “Watchdog

Timer unit select” in CMOS setup).

Table D-1: AH-6FH Sub-function

Call sub-function 2 to set the time-out period of Watchdog Timer first. If the time-out value is not zero, the Watchdog Timer starts counting down. When the timer value reaches zero, the system resets. To ensure that this reset condition does not occur, calling sub-function

2 must periodically refresh the Watchdog Timer. However, the watchdog timer is disabled if the time-out value is set to zero.

A tolerance of at least 10% must be maintained to avoid unknown routines within the operating system (DOS), such as disk I/O that can be very time-consuming.

Page 144


NOTE:

The Watchdog Timer is activated through software. The software application that activates the Watchdog Timer must also deactivate it when closed. If the Watchdog Timer is not deactivated, the system will automatically restart after the Timer has finished its countdown.

EXAMPLE PROGRAM:

; INITIAL TIMER PERIOD COUNTER

;

W_LOOP:

;

MOV AX, 6F02H ;setting the time-out value

MOV BL, 30 ;time-out value is 48 seconds

INT 15H

;

; ADD THE APPLICATION PROGRAM HERE

;

CMP EXIT_AP, 1 ;is the application over?

JNE W_LOOP ;No, restart the application

MOV AX, 6F02H ;disable Watchdog Timer

MOV BL, 0 ;

INT 15H

;

; EXIT ;

Page 145


Appendix

E

E

Hazardous Materials

Disclosure

Page 146


The details provided in this appendix are to ensure that the product is compliant with the

Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China

RoHS only.

A label will be placed on each product to indicate the estimated “Environmentally Friendly

Use Period” (EFUP). This is an estimate of the number of years that these substances would “not leak out or undergo abrupt change.” This product may contain replaceable sub-assemblies/components which have a shorter EFUP such as batteries and lamps.

These components will be separately marked.

Please refer to the following table.

Part Name Toxic or Hazardous Substances and Elements

Lead Mercury Cadmium Hexavalent

(Pb) (Hg) (Cd) Chromium

(CR(VI))

Polybrominated

Biphenyls

(PBB)

Polybrominated

Diphenyl Ethers

(PBDE)

Housing

Display

O O O O

O O O O

O

O

O

O

Printed Circuit

Board

Metal Fasteners

O O O O O O

Cable Assembly

O O O O

O O O O

O

O

O

O

Fan Assembly

Power Supply

Assemblies

O O O O

O O O O

O

O

O

O

Battery O O O O O O

O: This toxic or hazardous substance is contained in all of the homogeneous materials for the part is below the limit requirement in SJ/T11363-2006 (now replaced by GB/T 26572-2011).

X: This toxic or hazardous substance is contained in at least one of the homogeneous materials for this part is above the limit requirement in SJ/T11363-2006 (now replaced by GB/T 26572-2011).

Page 147


此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符

合中国 RoHS 标准规定的限量要求。

本产品上会附有 ” 环境友好使用期限 ” 的标签，此期限是估算这些物质 ” 不会有泄漏或突变 ” 的

年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元

件将会单独标示出来。

部件名称有毒有害物质或元素

壳体

显示

印刷电路板

铅

(Pb)

汞

(Hg)

镉

(Cd)

六价铬

(CR(VI))

多溴联苯

(PBB)

多溴二苯

醚

(PBDE)

O O O O O O

O O O O O O

O O O O O O

金属螺帽

电缆组装

O O O O O O

O O O O O O

风扇组装

电力供应组装

O O O O O O

O O O O O O

电池 O O O O O O

O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T 11363-2006 ( 现由 GB/T 26572-2011 取代 )

标准规定的限量要求以下。

X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 ( 现由 GB/T

26572-2011 取代 ) 标准规定的限量要求。

Page 148