IEI Integration POCm-W24C-ULT3 24” Medical Panel PC ULT Core™ i7/i5/Celeron® processor User Manual

POCm-W22/24C-ULT3 Medical Panel PC

MODEL:

POCm-W22/24C-ULT3

Medical Panel PC with 6

th

Gen. Intel® Core™ / Celeron® CPU,

4 GB DDR4 RAM, Wi-Fi 802.11a/b/g/n/ac, P-CAP Touchscreen,

Three Battery Bays, 5-Megapixel Camera and Microphone

Rev. 1.10 - March 5, 2021

Page i


Date

March 5, 2021

August 17, 2018

Revision

Version Changes

1.10

Updated Section 2.3: Optional Items

1.00 Initial release

Page ii


Copyright

COPYRIGHT NOTICE

The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

TRADEMARKS

All registered trademarks and product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective owners.

CONTACT INFORMATION

Manufactured by:

IEI Integration Corp.

Address:

Phone:

Fax:

No. 29, Zongxing Rd., Xizhi Dist.,

New Taipei City 221, Taiwan

+886-2-8691-6798

+886-2-6616-0028

Web Site: www.ieiworld.com

Sales Email: [email protected]

Page iii


Manual Conventions

WARNING

Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously.

CAUTION

Cautionary messages should be heeded to help reduce the chance of losing data or damaging the product.

NOTE

These messages inform the reader of essential but non-critical information. These messages should be read carefully as any directions or instructions contained therein can help avoid making mistakes.

Page iv


Table of Contents

1 INTRODUCTION .......................................................................................................... 1

1.1

O

VERVIEW

.................................................................................................................. 2

1.2

M

ODEL

V

ARIATIONS

................................................................................................... 3

1.3

F

EATURES

................................................................................................................... 3

1.4

F

RONT

P

ANEL

............................................................................................................. 4

1.4.1 Backlit Touch Buttons ........................................................................................ 5

1.4.2 LED Indicators ................................................................................................... 6

1.5

B

OTTOM

P

ANEL

.......................................................................................................... 7

1.6

S

IDE

P

ANELS

.............................................................................................................. 8

1.7

R

EAR

P

ANEL

............................................................................................................... 9

1.8

S

YSTEM

S

PECIFICATIONS

.......................................................................................... 10

1.9

D

IMENSIONS

............................................................................................................. 13

2 UNPACKING ............................................................................................................... 15

2.1

U

NPACKING

.............................................................................................................. 16

2.2

P

ACKING

L

IST

........................................................................................................... 17

2.3

O

PTIONAL

I

TEMS

...................................................................................................... 18

3 INSTALLATION ......................................................................................................... 20

3.1

S

AFETY

P

RECAUTIONS

............................................................................................. 21

3.2

A

NTI

-

STATIC

P

RECAUTIONS

...................................................................................... 22

3.3

I

NSTALLATION

P

RECAUTIONS

................................................................................... 23

3.4

I

NSTALLATION AND

C

ONFIGURATION

S

TEPS

............................................................. 23

3.5

HDD I

NSTALLATION

................................................................................................. 24

3.6

M.2

M-K

EY

M

ODULE

I

NSTALLATION

....................................................................... 26

3.7

B

ATTERY

I

NSTALLATION

(O

PTIONAL

) ....................................................................... 28

3.7.1 Battery Pack Specifications ............................................................................. 30

3.8

U

SING

RFID R

EADER

(O

PTIONAL

) ........................................................................... 30

3.9

RS-232/422/485 S

ERIAL

P

ORT

C

ONNECTION

........................................................... 33

3.10

AT/ATX M

ODE

S

ELECTION

.................................................................................... 34

3.10.1 AT Power Mode .............................................................................................. 34

Page v


3.10.2 ATX Power Mode ........................................................................................... 34

3.11

C

ABLE

C

OVER

I

NSTALLATION

(O

PTIONAL

)............................................................. 34

3.12

M

OUNTING THE

S

YSTEM

........................................................................................ 35

3.12.1 Wall Mounting ................................................................................................ 36

3.12.2 Arm Mounting ................................................................................................ 39

3.13

P

OWERING

O

N THE

S

YSTEM

................................................................................... 41

3.14

R

ESET THE

S

YSTEM

................................................................................................ 43

4 BIOS SETUP ................................................................................................................ 44

4.1

I

NTRODUCTION

......................................................................................................... 45

4.1.1 Starting Setup ................................................................................................... 45

4.1.2 Using Setup ...................................................................................................... 45

4.1.3 Getting Help ..................................................................................................... 46

4.1.4 BIOS Menu Bar ................................................................................................ 46

4.2

M

AIN

........................................................................................................................ 47

4.3

A

DVANCED

............................................................................................................... 48

4.3.1 CPU Configuration .......................................................................................... 49

4.3.2 PCH-FW Configuration ................................................................................... 50

4.3.3 Trusted Computing ........................................................................................... 52

4.3.4 ACPI Settings ................................................................................................... 53

4.3.5 F81866 Super IO Configuration ...................................................................... 54

4.3.5.1 Serial Port n Configuration ....................................................................... 54

4.3.5.1.1 Serial Port 1 Configuration ................................................................ 55

4.3.5.1.2 Serial Port 2 Configuration ................................................................ 56

4.3.6 iWDD H/W Monitor ......................................................................................... 57

4.3.7 RTC Wake Settings ........................................................................................... 58

4.3.8 Serial Port Console Redirection ...................................................................... 59

4.3.8.1 Console Redirection Settings .................................................................... 60

4.3.8.2 Legacy Console Redirection Settings ....................................................... 62

4.3.9 USB Configuration ........................................................................................... 63

4.3.10 IEI Feature ..................................................................................................... 64

4.4

C

HIPSET

................................................................................................................... 65

4.4.1 System Agent (SA) Configuration .................................................................... 65

4.4.1.1 Memory Configuration ............................................................................. 66

4.4.1.2 Graphics Configuration ............................................................................. 67

Page vi


4.4.1.2.1 LCD Control ...................................................................................... 69

4.4.2 PCH-IO Configuration .................................................................................... 70

4.4.2.1 PCI Express Configuration ....................................................................... 71

4.4.2.2 SATA Configuration .................................................................................. 73

4.4.2.3 HD Audio Configuration ........................................................................... 75

4.5

S

ECURITY

................................................................................................................. 76

4.6

B

OOT

........................................................................................................................ 77

4.7

S

AVE

& E

XIT

............................................................................................................ 79

5 DRIVER INSTALLATION ......................................................................................... 81

5.1

A

VAILABLE

D

RIVERS

................................................................................................ 82

5.2

D

RIVER

D

OWNLOAD

................................................................................................ 82

5.3

I

NTEL

® C

HIPSET

D

RIVER

......................................................................................... 84

5.4

I

NTEL

® G

RAPHICS

D

RIVER

...................................................................................... 85

5.5

A

UDIO

D

RIVER

......................................................................................................... 86

5.6

LAN D

RIVER

........................................................................................................... 87

5.7

I

NTEL

® M

ANAGEMENT

E

NGINE

............................................................................... 88

5.8

W

IRELESS

LAN D

RIVER

.......................................................................................... 89

5.9

B

LUETOOTH

D

RIVER

................................................................................................ 90

5.10

RFID D

RIVER

(O

PTIONAL

) ..................................................................................... 91

A REGULATORY COMPLIANCE .............................................................................. 94

B PRODUCT DISPOSAL .............................................................................................. 99

C MAINTENANCE AND CLEANING PRECAUTIONS ........................................ 101

C.1.1 Maintenance and Cleaning ........................................................................... 102

C.1.2 Cleaning Tools ............................................................................................... 103

D SYMBOL DEFINITIONS ........................................................................................ 104

E BIOS MENU OPTIONS ........................................................................................... 106

F WATCHDOG TIMER ............................................................................................... 109

G HAZARDOUS MATERIALS DISCLOSURE ........................................................ 112

Page vii


List of Figures

Figure 1-1: POCm-W22/24C-ULT3 Medical Panel PC .................................................................. 2

Figure 1-2: Front View .................................................................................................................... 4

Figure 1-3: Backlit Touch Buttons ................................................................................................ 5

Figure 1-4: LED Indicators ............................................................................................................. 6

Figure 1-5: Bottom Panel ............................................................................................................... 7

Figure 1-6: Side Views ................................................................................................................... 8

Figure 1-7: Rear View ..................................................................................................................... 9

Figure 1-8: POCm-W22C-ULT3 Dimensions (mm) .................................................................... 13

Figure 1-9: POCm-W24C-ULT3 Dimensions (mm) .................................................................... 14

Figure 3-1: HDD Cover Retention Screws .................................................................................. 24

Figure 3-2: HDD Bracket Retention Screws ............................................................................... 24

Figure 3-3: Secure HDD ............................................................................................................... 25

Figure 3-4: HDD Installation ........................................................................................................ 25

Figure 3-5: Bracket Retention Screws ........................................................................................ 26

Figure 3-6: M.2 Slots and Standoffs ........................................................................................... 27

Figure 3-7: Inserting the M.2 Module into the Slot at an Angle ............................................... 27

Figure 3-8: Securing the M.2 Module .......................................................................................... 28

Figure 3-9: Battery Cover Button ................................................................................................ 29

Figure 3-10: Battery Installation .................................................................................................. 29

Figure 3-11: RFID Program Location .......................................................................................... 31

Figure 3-12: IRFR-100 Icon .......................................................................................................... 31

Figure 3-13: IRFR Screen ............................................................................................................. 31

Figure 3-14: IRFR – Find Tags ..................................................................................................... 32

Figure 3-15: IRFR – UIDs .............................................................................................................. 32

Figure 3-16: AT/ATX Switch Location ......................................................................................... 34

Figure 3-17: Cable Cover Installation ......................................................................................... 35

Figure 3-18: Cable Cover Removal ............................................................................................. 35

Figure 3-19: Wall-mounting Bracket ........................................................................................... 37

Figure 3-20: Chassis Support Screws ........................................................................................ 38

Figure 3-21: Secure the Panel PC ............................................................................................... 39

Figure 3-22: Arm Mounting Retention Screw Holes .................................................................. 40

Page viii


Figure 3-23: Arm Mounting .......................................................................................................... 41

Figure 3-24: Power Input Connector ........................................................................................... 42

Figure 3-25: Reset Button Location ............................................................................................ 43

Figure 5-1: IEI Resource Download Center ................................................................................ 82

Figure 5-2: Intel® Chipset Device Software Installation Wizard .............................................. 84

Figure 5-3: Intel® Graphics Driver Installation Wizard ............................................................. 85

Figure 5-4: Realtek HD Audio Driver InstallShield Wizard ....................................................... 86

Figure 5-5: LAN Driver Installation Wizard ................................................................................ 87

Figure 5-6: Intel® ME Components Installation Wizard ............................................................ 88

Figure 5-7: Wireless LAN InstallShield Wizard .......................................................................... 89

Figure 5-8: Bluetooth Driver InstallShield Wizard ..................................................................... 90

Figure 5-9: Device Manager - Update Driver Software .............................................................. 91

Figure 5-10: Update Driver Software Window ........................................................................... 92

Figure 5-11: Browse for Driver Software Window ..................................................................... 92

Figure 5-12: Driver Installation Complete Window ................................................................... 93

Figure 5-13: Device Manager Window–RFID Devices ............................................................... 93

Page ix


List of Tables

Table 1-1: Model Variations ........................................................................................................... 3

Table 1-2: Touch Button Functions .............................................................................................. 5

Table 1-3: LED Indicators .............................................................................................................. 6

Table 1-4: System Specifications ................................................................................................ 12

Table 3-1: RS-232/422/485 Serial Port Pinouts .......................................................................... 33

Table 4-1: BIOS Navigation Keys ................................................................................................ 46

Page x


List of BIOS Menus

BIOS Menu 1: Main ....................................................................................................................... 47

BIOS Menu 2: Advanced .............................................................................................................. 48

BIOS Menu 3: CPU Configuration ............................................................................................... 49

BIOS Menu 4: PCH-FW Configuration ........................................................................................ 51

BIOS Menu 5: Trusted Computing .............................................................................................. 52

BIOS Menu 6: ACPI Settings ....................................................................................................... 53

BIOS Menu 7: F81866 Super IO Configuration .......................................................................... 54

BIOS Menu 8: Serial Port n Configuration Menu ....................................................................... 54

BIOS Menu 9: iWDD H/W Monitor ............................................................................................... 57

BIOS Menu 10: RTC Wake Settings ............................................................................................ 58

BIOS Menu 11: Serial Port Console Redirection ....................................................................... 59

BIOS Menu 12: Console Redirection Settings ........................................................................... 60

BIOS Menu 13: Legacy Console Redirection Settings ............................................................. 62

BIOS Menu 14: USB Configuration ............................................................................................. 63

BIOS Menu 15: IEI Feature ........................................................................................................... 64

BIOS Menu 16: Chipset ................................................................................................................ 65

BIOS Menu 17: System Agent (SA) Configuration .................................................................... 65

BIOS Menu 18: Memory Configuration ....................................................................................... 66

BIOS Menu 19: Graphics Configuration ..................................................................................... 67

BIOS Menu 20: LCD Control ........................................................................................................ 69

BIOS Menu 21: PCH-IO Configuration ........................................................................................ 70

BIOS Menu 22: PCI Express Configuration ............................................................................... 71

BIOS Menu 23: SATA Configuration ........................................................................................... 73

BIOS Menu 24: HD Audio Configuration .................................................................................... 75

BIOS Menu 25: Security ............................................................................................................... 76

BIOS Menu 26: Boot ..................................................................................................................... 77

BIOS Menu 27: Save & Exit .......................................................................................................... 79

Page xi


Chapter

1

1

Introduction

Page 1

1.1 Overview


Figure 1-1: POCm-W22/24C-ULT3 Medical Panel PC

The POCm-W22/24C-ULT3 is a 6 th

generation Intel® Core™ i5-6300U processor powered medical-grade panel PC with a rich variety of functions and peripherals. All

POCm-W22/24C-ULT3 models are designed for easy and simplified integration into point-of-care (POC) applications. The system comes with 4 GB of preinstalled DDR4 memory and supports a maximum of 32 GB ensuring smooth data throughputs with reduced bottlenecks and fast system access.

Two RS-232/422/485 serial ports, four USB 3.0 ports and two USB 2.0 ports provide simplified connectivity to a variety of external peripheral devices. Wi-Fi 802.11a/b/g/n/ac high speed wireless and two RJ-45 GbE connectors allow for smooth connection of the system to an external LAN. Three hot-swappable battery bays allow installation of three batteries to provide continuous power for 8~16 hours.

NOTE:

The POCm-W22/24C-ULT3 medical panel PC is intended to be used to display general purpose medical images. The device shall not be used for diagnosis purpose or life supporting system.

Page 2


1.2 Model Variations

There are six models in the POCm-W22/24C-ULT3 series. All models are preinstalled with one 4 GB DDR4 memory module and an 802.11a/b/g/n/ac Wi-Fi module. The model numbers and model variations are listed below.

Model

POCm-W22C-ULT3-C/PC/4G

POCm-W22C-ULT3-i5/PC/4G


POCm-W24C-ULT3-C/PC/4G



Table 1-1: Model Variations

CPU

Intel® Celeron® 3855U

Intel® Core™ i5-6300U


Intel® Celeron® 3855U



Size

21.5"

21.5"

21.5"

23.8"

23.8"

23.8"

1.3 Features

The POCm-W22/24C-ULT3 features are listed below:

 Fanless medical-grade panel PC with anti-bacteria cover

 Projected capacitive type touchscreen allows 10-point multi-touch, multi-layer gloves and water-on-screen operation

 Intel® Celeron® 3855U / Core™ i5-6300U / Core™ i7-6600U processor

 Preinstalled with 4 GB of DDR4 memory (system max. 32 GB)

 Two HDMI ports support additional displays

 Two GbE RJ-45 connectors and Wi-Fi 802.11a/b/g/n/ac high speed wireless

 Two internal 3 W speakers

 Four USB 3.0 ports and two USB 2.0 ports

 Two RS-232/422/485 DB-9 connector

 Support three hot-swappable batteries ideal for non-powered medical cart use

 IP 65 compliant front panel

Page 3


1.4 Front Panel

The front side of the POCm-W22/24C-ULT3 is a flat-bezel panel with a TFT LCD screen

surrounded by a PC+ABS plastic frame ( Figure 1-2 ).

Figure 1-2: Front View

Page 4


1.4.1 Backlit Touch Buttons

The front panel of the POCm-W22/24C-ULT3 contains several backlit touch buttons that control audio volume, LCD brightness and some other system components.

Figure 1-3: Backlit Touch Buttons

The following table describes the function of each button.

Button Function

Power on/off: long-press for 5 seconds.

−

: Brightness down (minimum brightness: 30%)

+: Brightness up (maximum brightness: 100%)

−

: Volume down

+: Volume up

Touch lock for cleaning: long-press for 3 seconds to lock or unlock the touch function of the screen. The touch buttons blink when the touch function is locked. The lock will be automatically released after 60 seconds.

LCD on/off: long-press for 5 seconds

Note: Press the touch button for at least one second to activate it.

Table 1-2: Touch Button Functions

Page 5


1.4.2 LED Indicators

The LED indicators on the front panel of the POCm-W22/24C-ULT3 are shown below.

Figure 1-4: LED Indicators

The descriptions of each LED indicator are listed below.

LED Indicator

Power

Description

Solid Blue: Power on

Solid Orange: Standby

Battery

Solid Blue: Battery capacity is above 25% (non-AC mode); Or battery is fully charged (AC mode)

Solid Orange: Battery capacity is 25%-10%

Blinking Orange: Battery capacity is less than 10%

Blinking Blue: Battery is charging

Table 1-3: LED Indicators

Page 6


1.5 Bottom Panel

The bottom panel of the POCm-W22/24C-ULT3 has the following connectors and

switches ( Figure 1-5 ):

 1 x DC input jack

 2 x HDMI output connector

 2 x GbE LAN (RJ-45 connector)

 2 x RS-232/422/485 serial port (DB-9 connector)

 4 x USB 3.0 connectors

 1 x AT/ATX switch

 1 x Reset button

 1 x Digital microphone

Figure 1-5: Bottom Panel

Page 7


1.6 Side Panels

The side panels have several I/O interfaces which are protected by waterproof covers.

The E-Window for I/O interface allows expansion by installing a PCIe Mini card.

Figure 1-6: Side Views

Page 8


1.7 Rear Panel

The rear panel contains three battery bays, two 3 W speakers, the camera cover on/off

switch and the retention screw holes that support VESA 75/100 mounting ( Figure 1-7 ).

HDD and M.2 modules can also be installed by removing the HDD cover located on the rear panel.

Figure 1-7: Rear View

Page 9


1.8 System Specifications

The technical specifications for the POCm-W22/24C-ULT3 systems are listed below.

LCD and Touchscreen

POCm-W22C-ULT3

LCD Size

Max. Resolution

Brightness (cd/m

2

)

21.5" (16:9)

1920 (W) x 1080 (H)

250

1000:1 Contrast Ratio

LCD Color 16.7M (RGB 6-bit)

0.24825 (H) x 0. 24825 (V) Pixel Pitch (mm)

Viewing Angle (H-V) 170°/160°

30,000 hrs (LED backlight) Backlight MTBF

Touchscreen

POCm-W24C-ULT3

23.8" (16:9)

1920 (W) x 1080 (H)

16.7M (RGB 6-bit + Hi-FRC)

0.2745 (H) x 0. 2745 (V)

Projected capacitive type with USB interface

10-point touch Multi-touch

Touch Controller

250

1000:1

178°/178°

30,000 hrs (LED backlight)

EETI

6H Surface Hardness

System

CPU

Memory

Intel® Celeron® 3855U / Intel® Core™ i5-6300U /


Two 260-pin 2133/1866 MHz dual-channel non-ECC unbuffered

DDR4 SO-DIMMs supported (system max. 32 GB)

Preinstalled with 4 GB memory

GbE Controller

I/O Ports

LAN1: Intel I211 Ethernet controller

LAN2: Intel® I219 Ethernet controller

1 x DC input jack

2 x HDMI output connector

2 x GbE LAN (RJ-45 connector)

2 x RS-232/422/485 serial port (DB-9 connector)

Page 10


4 x USB 3.0 connectors

2 x USB 2.0 connectors (side panel)

1 x Audio out (side panel)

1 x Mic-in (side panel)

1 x Digital microphone

One 2.5” SATA 6Gb/s HDD bay Storage

Audio Two 3 W speakers

Webcam & Microphone

5-megapixel CMOS front-facing camera with auto focus and digital microphone

Expansion Interface

2 x M.2 M-key 2242/2260/2280 slot (PCIe + SATA) with RAID

1 x M.2 A-/E-key 2242 slot (PCIe + USB)

1 x Full-size/Half-size PCIe Mini (PCIe + USB)

TPM 2.0 (optional) TPM

Other Features

Function Keys

LED Indicators

1 x Power on/off

1 x Brightness up

1 x Brightness down

1 x Volume up

1 x Volume down

1 x Touch lock (clean mode) or LCD on/off

3 x Battery indicator

1 x Power indicator

Fanless Cooling Method

Connectivity

Wi-Fi and Bluetooth

LAN

802.11a/b/g/n/ac dual band, Bluetooth v4.2

(M.2 2230 module, Intel® 8265)

Two GbE LAN connectors

Page 11


Physical

Construction Material PC+ABS plastic with anti-bacterial material

Mounting

Wall and stand mounting

VESA 75 mm x 75 mm or 100 mm x 100 mm

594.6 x 379.6 x 71 (mm) Dimensions (W x H x D) 543 x 350 x 71 (mm)

Net Weight 7.07 kg 8.18 kg

Environment

Temperature -20ºC ~ 60ºC

Storage/Transportation Humidity 10% ~ 90% (non-condensing)

700 hPa ~ 1060 hPa Pressure

Temperature 0ºC ~ 40ºC

Operating

Vibration

Shock

Humidity 10% ~ 90% (non-condensing)

Pressure 700 hPa ~ 1060 hPa

1G

Operating Shock: 5G peak acceleration (11ms duration)

Non-Operating Shock: 10G peak acceleration (11ms duration)

IP 65 compliant front panel IP Level

Power

Power Input 19 V DC

150 W FSP FSP150M-ABA medical-grade power adapter

( P/N : 63040-010150-400-RS)

Power Adapter

Input : 100 V AC ~ 240 V AC, 50 Hz ~ 60 Hz, 2 A ~ 0.85 A

Output : 19 V 7.89 A

3 x Hot-swappable battery bay Battery

Table 1-4: System Specifications

Page 12


1.9 Dimensions

The POCm-W22C-ULT3 dimensions are shown below.

Figure 1-8: POCm-W22C-ULT3 Dimensions (mm)

Page 13


The POCm-W24C-ULT3 dimensions are shown below.

Figure 1-9: POCm-W24C-ULT3 Dimensions (mm)

Page 14


Chapter

2

2

Unpacking

Page 15


2.1 Unpacking

To unpack the medical panel PC, follow the steps below:

WARNING!

The front side LCD screen has a protective plastic cover stuck to the screen. Only remove the plastic cover after the medical panel PC has been properly installed. This ensures the screen is protected during the installation process.

Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the external (second) box.

Step 2: Open the external (second) box.

Step 3: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the internal (first) box.

Step 4: Lift the panel PC out of the boxes.

Step 5: Remove both polystyrene ends, one from each side.

Step 6: Pull the plastic cover off the medical panel PC.

Step 7: Make sure all the components listed in the packing list are present. Step 0:

Page 16


2.2 Packing List

NOTE:

If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the

POCm-W22/24C-ULT3 was purchased from or contact an IEI sales representative directly by sending an email to [email protected]

.

The POCm-W22/24C-ULT3 medical panel PC is shipped with the following components:

Quantity Item

1

POCm-W22/24C-ULT3 medical panel PC

Image

1

4

1 150 W FSP FSP150M-ABA medical-grade power adapter

( P/N : 63040-010150-400-RS)

Power cord (EU)

( P/N : 32702-000200-100-RS)

Round-head screw (M3*3) for HDD installation

( P/N : 44003-030032-RS)

Page 17


2.3 Optional Items

The following are optional components which may be separately purchased:

Item and Part Number

Li-ion battery pack, 3S3P, 7800 mAh

( P/N : MEDP-HSBAT-R10)

Image

Cable cover

( P/N : 43106-0272Q7-00-RS)

VESA 100 wall mount kit (four M3*6 screws included)

( P/N : AFLWK-19B)

Arm

( P/N : ARM-31-RS)

Stand

( P/N : STAND-A21-R10)

Page 18


Item and Part Number

Mifare RFID reader compliant with ISO 14443A, ISO

14443B and ISO 15693 protocols (assemble-to-order)

( P/N : MEDP-MF-RFID-R10)

20-pin Infineon TPM 2.0 module, software management tool, firmware v5.5 (assemble-to-order)

( P/N : TPM-IN02-R20)

Image

6-slot charging station dock, 300 W

( P/N : POCm-DOCKING-6BAY-R10)

Page 19


Chapter

3

3

Installation

Page 20


3.1 Safety Precautions

Please ensure the following safety precautions are adhered to at all times.

 To prevent the risk of electric shock, make sure power cord is unplugged from wall socket.

To fully disengage the power to the unit, please disconnect the power cord from the ac outlet. Refer servicing to qualified service personnel. The AC outlet shall be readily available and accessible.

 Users must not allow SIP/SOPs and the patient to come into contact at the same time.

 Grounding reliability can only be achieved when the equipment is connected to an equivalent receptacle marked “Hospital Only” or “Hospital

Grade”.

 Follow the electrostatic precautions outlined below whenever the

POCm-W22/24C-ULT3 is opened.

 Make sure the power is turned off and the power cord is disconnected whenever the POCm-W22/24C-ULT3 is being installed, moved or modified.

 Do not apply voltage levels that exceed the specified voltage range .

Doing so may cause fire and/or an electrical shock. Use a power cord that matches the voltage of the power outlet, which has been approved and complies with the safety standard of your particular country.

 Electric shocks can occur if the POCm-W22/24C-ULT3 chassis is opened when the POCm-W22/24C-ULT3 is running. To avoid risk of electric shock, this equipment must only be connected to a supply mains with protective earth.

 DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED

ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°

C (-4°F) OR ABOVE 60° C (140° F). IT MAY DAMAGE THE EQUIPMENT.

 Do not drop or insert any objects into the ventilation openings of the

POCm-W22/24C-ULT3.

 If considerable amounts of dust, water, or fluids enter the

POCm-W22/24C-ULT3 , turn off the power supply immediately, unplug the power cord, and contact the POCm-W22/24C-ULT3 vendor.

Page 21


 DO NOT : o Drop the POCm-W22/24C-ULT3 against a hard surface. o Strike or exert excessive force onto the LCD panel. o Touch any of the LCD panels with a sharp object o In a site where the ambient temperature exceeds the rated temperature

3.2 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the maintenance of the

POCm-W22/24C-ULT3 may result in permanent damage to the

POCm-W22/24C-ULT3 and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components, including the POCm-W22/24C-ULT3. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the POCm-W22/24C-ULT3 is accessed internally, or any other electrical component is handled, the following anti-static precautions are strictly adhered to.

 Wear an anti-static wristband : Wearing a simple anti-static wristband can help to prevent ESD from damaging the board.

 Self-grounding : Before handling the board, touch any grounded conducting material. During the time the board is handled, frequently touch any conducting materials that are connected to the ground.

 Use an anti-static pad : When configuring the POCm-W22/24C-ULT3, place it on an anti-static pad. This reduces the possibility of ESD damaging the

POCm-W22/24C-ULT3.

 Only handle the edges of the PCB : When handling the PCB, hold the PCB by the edges.

Page 22


3.3 Installation Precautions

When installing the medical panel PC, please follow the precautions listed below:

 Manufacturer authorization : Do not modify this equipment without authorization of manufacturer.

 Certified Engineers : Only certified engineers should install and modify the hardware settings.

 Power turned off : When installing the medical panel PC, make sure the power is off. Failing to turn off the power may cause severe injury to the body and/or damage to the system.

 Anti-static Discharge : If a user open the rear panel of the medical panel PC, to configure the jumpers or plug in added peripheral devices, ground themselves first and wear an anti-static wristband.

WARNING:

DO NOT power up the POCm-W22/24C-ULT3 while the front panel is facing down on a sheet of conductive foam. Doing so may cause the touch panel to malfunction due to the large surface area of contact between the conductive form and the touch panel.

3.4 Installation and Configuration Steps

The following installation steps must be followed.

Step 1: Unpack the medical panel PC.

Step 2: Install an HDD.

Step 3: Configure the system.

Step 4: Connect peripheral devices to the medical panel PC.

Step 5: Mount the medical panel PC.

Step 0:

Page 23


3.5 HDD Installation

To install the HDD into the system, please follow the steps below:

Step 1:

Remove the two HDD cover retention screws on the rear panel ( Figure 3-1 ).

Figure 3-1: HDD Cover Retention Screws

Step 2: Remove the HDD cover.

Step 3:

Remove the two HDD bracket retention screws ( Figure 3-2 ) and lift the HDD

bracket off the panel PC.

Page 24

Figure 3-2: HDD Bracket Retention Screws


Step 4: Insert an HDD into the HDD bracket, aligning the four retention screw holes on the bottom of the HDD bracket with the retention screw holes on the bottom of

the HDD ( Figure 3-3 ).

Step 5:

Insert four retention screws (M3*3) into the bracket ( Figure 3-3 ).

Figure 3-3: Secure HDD

Step 6: Place the HDD and slide it to securely connect to the SATA connector of the

POCm-W22/24C-ULT3 ( Figure 3-4 ).

Step 7: Secure the HDD bracket by fastening the two retention screws previously

removed ( Figure 3-4 ).

Figure 3-4: HDD Installation

Step 8: Re-install the HDD cover. Step 0:

Page 25


3.6 M.2 M-Key Module Installation

NOTE:

The two M.2 M-key slots are both set to PCIe mode by default.

Configure the M.2 slots as mSATA interface in BIOS before installing mSATA modules (please refer to

Section 4.4.2.1

). Please be noted

that the C SKUs do not support M.2 mSATA modules due to Intel®

Celeron® 3855U CPU limitation.

To install M.2 modules into the system, please follow the steps below:

Step 1: Follow the Step 1 ~ Step 3 instruction described in

Section 3.5

to remove HDD

cover and HDD bracket.

Step 2: Remove the three retention screws shown below to lift the bracket off the panel

PC.

Figure 3-5: Bracket Retention Screws

Step 3: Locate the M.2 M-key slots. Each slot has its brass standoff on the side for installation.

Step 4: Remove the screw on the brass standoff first, and then remove the standoff.

Page 26


Install the standoff into the corresponding screw hole based on the size of the

M.2 module to be installed. See Figure 3-6 .

Figure 3-6: M.2 Slots and Standoffs

Step 5: Line up the notch on the M.2 module with the notch on the slot. Slide the M.2

module into the socket at an angle of about 20º ( Figure 3-7 ).

Figure 3-7: Inserting the M.2 Module into the Slot at an Angle

Step 6: Secure the M.2 module with the previously removed retention screw

( Figure 3-8 ).

Page 27


Figure 3-8: Securing the M.2 Module

Step 7: Re-install the brackets and the HDD cover. Step 0:

3.7 Battery Installation (Optional)

WARNING:

 Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.

 Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.

 Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.

 A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

The POCm-W22/24C-ULT3 has three battery bays for Li-ion battery pack installation. To install battery, please follow the steps below.

Step 1: Press the battery door button to release the latch and open the battery door.

Page 28


Figure 3-9: Battery Cover Button

Step 2: Insert a battery in the direction shown below and push it to the bottom.

Figure 3-10: Battery Installation

Step 3: Fold the battery strap inwards and close the battery door.

Page 29

3.7.1 Battery Pack Specifications


The followings are some of the specifications of the optional Li-ion battery pack.

 Capacity: 7800 mAh

 Normal voltage: 11.1V

 Charge voltage: 12.6 V

 Continuous charge current: 2.6 A

 Continuous discharge current: 5 A

 Storage temperature: 0ºC ~ 40ºC

Each battery pack provides four LED indicators, allowing the user to get an indication of battery capacity by pushing the button below the indicators. The LED level meanings are listed below:

 1 LED: 1~25% capacity level

 2 LEDs: 26~50% capacity level



3.8 Using RFID Reader (Optional)

The POCm-W22/24C-ULT3 may come with an optional RFID reader pre-installed inside the bottom of the front panel. To use the RFID reader, follow the steps below.

Step 1: Install the RFID driver (refer to

Section 5.10

).

Step 1: Locate the IRFR-100.exe file in the following driver directory: \11.RFID\D490.

Copy the IRFR-100.exe

program to the desktop.

Page 30


Figure 3-11: RFID Program Location

Step 2: Double click the IRFR-100 icon on the desktop.

Figure 3-12: IRFR-100 Icon

Step 3:

The IRFR-100 window appears ( Figure 3-13 ).

Figure 3-13: IRFR Screen

Step 4: Select the Find tags tab and click the Run button to enable the RFID reader

( Figure 3-14 ).

Page 31


Figure 3-14: IRFR – Find Tags

Step 5: Place an RFID card near the RFID reader on the bottom of the front

panel ( Figure 1-2 ) then remove it. The card number will be shown in the UIDs

column ( Figure 3-15 ).

Figure 3-15: IRFR – UIDs

Page 32


NOTE:

Please refer to the IRFR-100 user guide in the driver folder

(IRFR-100_AP_UserGuide.pdf) for detailed instruction on how to use the IRFR-100.

3.9 RS-232/422/485 Serial Port Connection

The bottom panel of the POCm-W22/24C-ULT3 has two DB-9 male connectors for

RS-232/422/485 connection. The serial communication mode selection can be made through the BIOS options. Please refer to

Section 4.3.5.1

for detailed information. The

pinouts of the DB-9 connector are listed below.

Pin

7

8

5

6

3

4

1

2

9

RS-232

DCD

RX

TX

DTR

GND

DSR

RTS

CTS

RI

RS-422

TXD422-

TXD422+

RXD422+

RXD422-

Table 3-1: RS-232/422/485 Serial Port Pinouts

RS-485

TXD485-

TXD485+

Page 33


3.10 AT/ATX Mode Selection

AT or ATX power mode can be used on the POCm-W22/24C-ULT3. The selection is

made through an AT/ATX switch located on the bottom panel ( Figure 3-16 ).

Figure 3-16: AT/ATX Switch Location

3.10.1 AT Power Mode

With the AT mode selected, the power is controlled by a central power unit rather than a power switch. The POCm-W22/24C-ULT3 panel PC turns on automatically when the power is connected.

3.10.2 ATX Power Mode

With the ATX mode selected, the POCm-W22/24C-ULT3 panel PC goes in a standby mode when it is turned off. The panel PC can be easily turned on via network or a power switch in standby mode.

3.11 Cable Cover Installation (Optional)

An optional cable cover can be installed on the POCm-W22/24C-ULT3 for the user to easily manage cables. To install the cable cover, please follow the instruction below.

Step 1: Align the two tabs on cable cover with the slots on the bottom panel of the

POCm-W22/24C-ULT3 ( Figure 3-17 ). Then, insert the tabs into the slots.

Step 2:

Push the cable cover down to clip the cover into place ( Figure 3-17 ).

Page 34


Figure 3-17: Cable Cover Installation

Step 3: To remove the cable cover, push the two tabs inwards to release the cover

( Figure 3-18 ), and lift the cover from the POCm-W22/24C-ULT3.

Figure 3-18: Cable Cover Removal

3.12 Mounting the System

The methods of mounting the POCm-W22/24C-ULT3 are listed below.

 Wall mounting

 Arm mounting

The mounting methods are described below.

Page 35


WARNING:

1. When mounting the POCm-W22/24C-ULT3 flat panel PC, it is better to have more than one person to help with the installation to make sure the POCm-W22/24C-ULT3 does not fall down and get damaged.

2. Use suitable mounting apparatus and be sure to secure the screws of the mounting apparatus tightly to avoid risk of injury.

3.12.1 Wall Mounting

To mount the medical panel PC onto the wall, please follow the steps below.

Step 1: Select the location on the wall for the wall-mounting bracket.

Step 2: Carefully mark the locations of the four screw holes in the bracket on the wall.

Step 3: Drill four pilot holes at the marked locations on the wall for the bracket retention screws.

Step 4: Align the wall-mounting bracket screw holes with the pilot holes.

Step 5: Secure the mounting-bracket to the wall by inserting the retention screws into

the four pilot holes and tightening them ( Figure 3-19 ).

Page 36


Figure 3-19: Wall-mounting Bracket

Step 6: Insert the four mounting screws provided in the wall mount kit into the four screw holes on the real panel of the medical panel PC and tighten until the screw

shank is secured against the rear panel ( Figure 3-20 ).

WARNING:

Please use the M4 screws provided in the wall mount kit for the rear panel.

If the screw is missing, the thread depth of the replacement screw should be not more than 4 mm.

Step 7: Align the mounting screws on the rear panel with the mounting holes on the bracket.

Step 8: Carefully insert the screws through the holes and gently pull the panel PC downwards until the panel PC rests securely in the slotted holes ( Figure 3-20 ).

Page 37


Ensure that all four of the mounting screws fit snugly into their respective slotted holes.

NOTE:

In the diagram below the bracket is already installed on the wall.

Figure 3-20: Chassis Support Screws

Step 9: Secure the panel PC by fastening the retention screw of the wall-mounting bracket ( Figure 3-21 ).

Page 38


Figure 3-21: Secure the Panel PC

3.12.2 Arm Mounting

The POCm-W22/24C-ULT3 is VESA (Video Electronics Standards Association) compliant and can be mounted on an arm with a 75 mm or 100 mm interface pad. To mount the

POCm-W22/24C-ULT3 on an arm, please follow the steps below.

Step 1: The arm is a separately purchased item. Please correctly mount the arm onto the surface it uses as a base. To do this, refer to the installation documentation that came with the mounting arm.

Page 39


NOTE:

When purchasing the arm please ensure that it is VESA compliant and that the arm has a 75 mm or 100 mm interface pad. If the mounting arm is not

VESA compliant it cannot be used to support the POCm-W22/24C-ULT3 medical panel PC.

Step 2: Once the mounting arm has been firmly attached to the surface, lift the panel PC onto the interface pad of the mounting arm.

Step 3: Align the retention screw holes on the mounting arm interface with those in the

panel PC ( Figure 3-22 ).

Figure 3-22: Arm Mounting Retention Screw Holes

Step 4: Secure the POCm-W22/24C-ULT3 to the interface pad by inserting four retention screws through the mounting arm interface pad and into the

POCm-W22/24C-ULT3.

p

Page 40


Figure 3-23: Arm Mounting

3.13 Powering On the System

WARNING:

To avoid risk of electric shock, this equipment must only be connected to supply mains with protective earth.

CAUTION:

The FSP FSP150M-ABA power adapter came with the

POCm-W22/24C-ULT3 is a forming part of the medical device.

Page 41


To power on the system, follow the steps below:

Step 1: Connect the power cord to the power adapter. Connect the other end of the power cord to a power source.

Step 2: Connect the power adapter to the power connector of the

POCm-W22/24C-ULT3.

Figure 3-24: Power Input Connector

Step 3:

Locate the power button on the right panel ( Figure 1-6 ).

Step 4: Short press the power button to turn on the POCm-W22/24C-ULT3. Step 0:

NOTE:

1. The user can also long-press the touch button on the front

panel for 5 seconds to power on the system (please refer to Table 1-2 ).

2. Long-press the power button for 10 seconds to force shutdown the panel PC.

Page 42


3.14 Reset the System

The reset button enables user to reboot the system when the system is turned on. The

reset button location is shown in Figure 3-25 . Press the reset button to reboot the system.

Figure 3-25: Reset Button Location

Page 43


Chapter

4

4

BIOS Setup

Page 44


4.1 Introduction

The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed.

NOTE:

Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice.

4.1.1 Starting Setup

The UEFI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways.

1. Press the DEL key as soon as the system is turned on or

2. Press the DEL key when the “ Press DEL to enter SETUP ” message appears on the screen. 0.

If the message disappears before the DEL key is pressed, restart the computer and try again.

4.1.2 Using Setup

Use the arrow keys to highlight items, press E

NTER

to select, use the PageUp and

PageDown keys to change entries, press F1 for help and press E

SC

to quit. Navigation keys are shown in the following table.

Key Function

Up arrow Move to the item above

Down arrow Move to the item below

Left arrow Move to the item on the left hand side

Right arrow Move to the item on the right hand side

+ Increase the numeric value or make changes

Page 45

-

F1 key

F2 key

F3 key

F4 key

Esc key


Decrease the numeric value or make changes

General help, only for Status Page Setup Menu and Option

Page Setup Menu

Load previous values.

Load optimized defaults

Save changes and Exit BIOS

Main Menu – Quit and do not save changes into CMOS

Status Page Setup Menu and Option Page Setup Menu --

Exit current page and return to Main Menu

Table 4-1: BIOS Navigation Keys

4.1.3 Getting Help

When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press E SC or the F1 key again.

4.1.4 BIOS Menu Bar

The menu bar on top of the BIOS screen has the following main items:

 Main – Changes the basic system configuration.

 Advanced – Changes the advanced system settings.

 Chipset – Changes the chipset settings.

 Security – Sets User and Supervisor Passwords.

 Boot – Changes the system boot configuration.

 Save & Exit – Selects exit options and loads default settings

The following sections completely describe the configuration options found in the menu items at the top of the BIOS screen and listed above.

Page 46


4.2 Main

The Main

BIOS menu ( BIOS Menu 1 ) appears when the

BIOS Setup program is entered.

The Main menu gives an overview of the basic system information.

Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc.

Main Advanced Chipset Security Boot Save & Exit

BIOS Information

BIOS Vendor

Core Version

Compliancy

Project Version

Build Date and Time iWDD Vendor iWDD Version

Processor Information

Name

American Megatrends

5.12

UEFI 2.6; PI 1.4

V3SNAT11.ROM

06/21/2018 11:08:07 iEi

Z450ER11.bin

Set the Date. Use Tab to switch between Date elements.

Skylake ULT

Intel(R) Core(TM) i5-6300U CPU @ 2.40GHz

2500 MHz

0x406E3

D0/K0

2Core(S)/4Thread(s)

C2

GT2 (0x1916)

Type

Speed

ID

Stepping

Number of Processors

Microcode Revision

GT Info

IGF VBIOS Version

Memory RC Version

Total Memory

Memory Frequency

PCH Information

Name

PCH SKU

Stepping

LAN PHY Revision

ME FW Version

ME Firmware SKU

SPI Clock Frequency

1054

2.0.0.6

4096 MB

2133 MHz

SKL PCH-LP

(U) Premium SKU

C1

A6 (B2 Stepping)

11.8.50.3425

Corporate SKU

----------------------



: Select Screen

↑ ↓

: Select Item

D0FR Support Not supported

Read Status Clock Frequency 17 MHz

Write Status Clock Frequency 17 MHz

Fast Read Status Clock Frequency 17 MHz

System Date [Thu 07/27/2018]

[16:49:37] System Time

Access Level Administrator

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Version 2.18.1263. Copyright (C) 2018 American Megatrends, Inc.

BIOS Menu 1: Main

Page 47


 System Date [xx/xx/xx]

Use the System Date option to set the system date. Manually enter the day, month and year.

 System Time [xx:xx:xx]

Use the System Time option to set the system time. Manually enter the hours, minutes and seconds.

4.3 Advanced

Use the Advanced

menu ( BIOS Menu 2 ) to configure the CPU and peripheral devices

through the following sub-menus:

WARNING:

Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware.



> CPU Configuration Trusted Computing

> PCH-FW Configuration

> Trusted Computing

Settings

> ACPI Settings

> F81866 Super IO Configuration

> iWDD H/M Monitor

> RTC Wake Settings

----------------------



: Select Screen

↑ ↓

: Select Item

> Serial Port Console Redirection

> USB Configuration

> iEi Feature

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 2: Advanced

Page 48


4.3.1 CPU Configuration

Use the CPU Configuration

( BIOS Menu 3 ) to view detailed CPU specifications and

configure the CPU.


Advanced

CPU Configuration

Type

ID

Speed

L1 Data Cache

L1 Instruction Cache

L2 Cache

L3 Cache

L4 Cache

VTX

SMX/TXT

Intel(R) Core(TM) i5-6300U CPU @ 2.40GHz

0x406E3

2500 MHz

32 kB x 2

32 kB x 2

256 kB x 2

3 MB

N/A

Supported

Supported

When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool

Technology.

----------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

Intel (VMX) Virtualization [Disabled]

F1: General Help

Technology

F2: Previous Values

Active Processor Cores [All]


Hyper-Threading [Enabled]

F4: Save & Exit

Intel Trusted Execution Technology [Disabled]

ESC: Exit

Intel(R) SpeedStep(tm) [Enabled]

CPU C states [Disabled]


BIOS Menu 3: CPU Configuration

 Intel (VMX) Virtualization Technology [Disabled]

Use the Intel (VMX) Virtualization Technology option to enable or disable virtualization on the system. When combined with third party software, Intel® Virtualization technology allows several OSs to run on the same system at the same time.



Disabled



Enabled

D EFAULT

Disables Intel Virtualization Technology.

Enables Intel Virtualization Technology.

 Active Processor Cores [All]

Use the Active Processor Cores BIOS option to enable numbers of cores in the processor package.

Page 49



All



1


D EFAULT Enable all cores in the processor package.

Enable one core in the processor package.

 Hyper-Threading [Enabled]

Use the Hyper-Threading option to enable or disable the Intel® Hyper-Threading

Technology.



Disabled



Enabled

Disable Intel® Hyper-Threading Technology

D EFAULT

Enable Intel® Hyper-Threading Technology

 Intel

®

SpeedStep(tm) [Enabled]

Use the Intel

®

SpeedStep™ option to enable or disable the Intel

®

SpeedStep

Technology.



Disabled



Enabled D EFAULT

Disables the Intel

®

SpeedStep Technology.

Enables the Intel

®

SpeedStep Technology.

 CPU C State [Disabled]

Use the CPU C State option to enable or disable CPU C state.



Enabled



Disabled D EFAULT

Enables CPU C state.

Disables CPU C state.

4.3.2 PCH-FW Configuration

The PCH-FW Configuration

menu ( BIOS Menu 4 ) allows Intel® Active Management

Technology (AMT) options to be configured.

Page 50



Advanced

AMT BIOS Features

Unconfigure ME

[Enabled]

[Disabled]

When disabled AMT BIOS

Features are no longer supported and user is no longer able to access

MEBx Setup.

Note:

This option does not disable Manageability

Features in FW.

---------------------



: Select Screen

↑ ↓

: Select Item

F1 General Help

F2 Previous Values

F3 Optimized

Defaults

F4 Save

ESC Exit


BIOS Menu 4: PCH-FW Configuration

 AMT BIOS Features [Enabled]

Use AMT BIOS Features option to enable or disable the access to MEBx Setup.



Disabled




Unable to access MEBx Setup

Allow access to MEBx Setup

 Unconfigure ME [Disabled]

Use the Unconfigure ME option to perform ME unconfigure without password operation.



Disabled D

EFAULT



Enabled

Not perform AMT/ME unconfigure

To perform AMT/ME unconfigure

Page 51


4.3.3 Trusted Computing

Use the Trusted Computing

menu ( BIOS Menu 5 ) to configure settings related to the

Trusted Computing Group (TCG) Trusted Platform Module (TPM).


Advanced

Configuration

Security Device Support

NO Security Device Found

[Disable]

Enables or Disables BIOS support for security device. O.S. will not show Security Device.

TCG EFI protocol and

INT1A interface will not be available.

----------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 5: Trusted Computing

 Security Device Support [Disable]

Use the Security Device Support option to configure support for the security devices.



Disable D EFAULT Security device support is disabled.



Enable Security device support is enabled.

Page 52


4.3.4 ACPI Settings

The ACPI Settings

menu ( BIOS Menu 6 ) configures the Advanced Configuration and

Power Interface (ACPI) options.


Advanced

ACPI Settings

ACPI Sleep State [S3 (Suspend to RAM)]

Select ACPI sleep state the system will enter when the SUSPEND button is pressed.

----------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 6: ACPI Settings

 ACPI Sleep State [S3 (Suspend to RAM)]

Use the ACPI Sleep State option to specify the sleep state the system enters when it is not being used.



S3 (Suspend to

RAM)

D EFAULT

The caches are flushed and the CPU is powered off. Power to the RAM is maintained. The computer returns slower to a working state, but more power is saved.

Page 53


4.3.5 F81866 Super IO Configuration

Use the F81866 Super IO Configuration

menu ( BIOS Menu 7 ) to set or change the

configurations for the serial ports.


Advanced

F81866 Super IO Configuration

Super IO Chip

> Serial Port 1 Configuration

> Serial Port 2 Configuration

F81866

Set Parameters of Serial

Port 1 (COMA)

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 7: F81866 Super IO Configuration

4.3.5.1 Serial Port n Configuration

Use the Serial Port n Configuration

menu ( BIOS Menu 8 ) to configure the serial port n.


Advanced

Serial Port 1 Configuration

Serial Port

Device Settings

Change Settings

Device Mode

[Enabled]

IO=3F8h; IRQ=4

[Auto]

[RS232]

Enable or Disable Serial

Port (COM)

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 8: Serial Port n Configuration Menu

Page 54


4.3.5.1.1 Serial Port 1 Configuration

 Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.



Disabled




Disable the serial port

Enable the serial port

 Change Settings [Auto]

Use the Change Settings option to change the serial port IO port address and interrupt address.



Auto



IO=3F8h; IRQ=4

D EFAULT

The serial port IO port address and interrupt address are automatically detected.

Serial Port I/O port address is 3F8h and the interrupt address is IRQ4



IO=3F8h;

IRQ=3, 4, 5, 6, 7,

9, 10, 11, 12

Serial Port I/O port address is 3F8h and the interrupt address is IRQ3, 4, 5, 6, 7, 9, 10, 11,

12



IO=2F8h;

IRQ=3, 4, 5, 6, 7,

9, 10, 11, 12


12



IO=3E8h;

IRQ=3, 4, 5, 6, 7,

9, 10, 11, 12

Serial Port I/O port address is 3E8h and the interrupt address is IRQ3, 4, 5, 6, 7, 9, 10, 11,

12



IO=2E8h;

IRQ=3, 4, 5, 6, 7,

9, 10, 11, 12


12

 Device Mode [RS232]

Use the Device Mode option to set the Serial Port 1 signaling mode.

Page 55



RS422



RS232



RS485

D EFAULT


Configure Serial Port 1 as RS-422



4.3.5.1.2 Serial Port 2 Configuration

 Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.



Disabled




Disable the serial port

Enable the serial port

 Change Settings [Auto]

Use the Change Settings option to change the serial port IO port address and interrupt address.



Auto



IO=2F8h; IRQ=3

D EFAULT

The serial port IO port address and interrupt address are automatically detected.

Serial Port I/O port address is 2F8h and the interrupt address is IRQ3



IO=3F8h;

IRQ=3, 4, 5, 6, 7,

9, 10, 11, 12


12



IO=2F8h;

IRQ=3, 4, 5, 6, 7,

9, 10, 11, 12


12



IO=3E8h;

IRQ=3, 4, 5, 6, 7,

9, 10, 11, 12


12



IO=2E8h;

IRQ=3, 4, 5, 6, 7,

9, 10, 11, 12


12

Page 56


 Device Mode [RS232]

Use the Device Mode option to set the Serial Port 2 signaling mode.



RS422



RS232



RS485

D EFAULT




4.3.6 iWDD H/W Monitor

The iWDD H/W Monitor

menu ( BIOS Menu 9 ) shows the operating temperatures and

voltages.


Advanced

PC Health Status

CPU temperature

System temperature

CPU_CORE

+5V

+5VSB

+3.3V

+3.3VSB

: +31 °C

: +34 °C

: +0.880 V

: +5.003 V

:

:

:

+4.944 V

+3.328 V

+3.344 V

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 9: iWDD H/W Monitor

 PC Health Status

The following system parameters and values are shown. The system parameters that are monitored are:

 Temperature: o CPU Temperature o System Temperature

 Voltages: o CPU_CORE

Page 57

POCm-W22/24C-ULT3 Medical Panel PC o +5V o +5VSB o +3.3V o +3.3VSB

4.3.7 RTC Wake Settings

The RTC Wake Settings

menu ( BIOS Menu 10 ) configures RTC wake event.


Advanced

Wake system with Fixed Time [Disabled] Enable or disable System wake on alarm event. When enabled, System will wake on the dat::hr::min::sec specified

----------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 10: RTC Wake Settings

 Wake System with Fixed Time [Disabled]

Use the Wake System with Fixed Time option to specify the time the system should be roused from a suspended state.



Disabled D

EFAULT

The real time clock (RTC) cannot generate a wake event

Page 58




Enabled If selected, the following appears with values that can be selected:

*Wake up every day

*Wake up date

*Wake up hour

*Wake up minute

*Wake up second

After setting the alarm, the computer turns itself on from a suspend state when the alarm goes off.

4.3.8 Serial Port Console Redirection

The Serial Port Console Redirection

menu ( BIOS Menu 11 ) allows the console

redirection options to be configured. Console redirection allows users to maintain a system remotely by re-directing keyboard input and text output through the serial port.


Advanced

COM1

Console Redirection

> Console Redirection Settings

[Disabled]

Console Redirection

Enable or Disable.

COM2

Console Redirection

> Console Redirection Settings iAMT SOL

COM3(PCi Bus0,Dev22,Func3)

Console Redirection

[Disabled]

[Disabled]

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

> Console Redirection Settings

Legacy Console Redirection

> Legacy Console Redirection Settings

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 11: Serial Port Console Redirection

Page 59

 Console Redirection [Disabled]


Use Console Redirection option to enable or disable the console redirection function.






Enabled

Disabled the console redirection function

Enabled the console redirection function

4.3.8.1 Console Redirection Settings

Use the Console Redirection Settings

menu ( BIOS Menu 12 ) to configure console

redirection settings of the specified serial port. This menu appears only when the Console

Redirection option is enabled.


Advanced

COM1

Console Redirection Settings

Terminal Type

Bits per second

Data Bits

Parity

Stop Bits

[ANSI]

[115200]

[8]

[None]

[1]

Emulation: ANSI: Extended

ASCII char set. VT100:

ASCII char set. VT100+:

Extends VT100 to support color, function keys, etc.

VT-UTF8: Uses UTF8 encoding to map Unicode chars onto 1 or more bytes.

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 12: Console Redirection Settings

 Terminal Type [ANSI]

Use the Terminal Type option to specify the remote terminal type.



VT100



VT100+

The target terminal type is VT100

The target terminal type is VT100+

Page 60




VT-UTF8 The target terminal type is VT-UTF8



ANSI D EFAULT The target terminal type is ANSI

 Bits per second [115200]

Use the Bits per second option to specify the serial port transmission speed. The speed must match the other side. Long or noisy lines may require lower speeds.



9600



19200



57600



115200 D EFAULT

Sets the serial port transmission speed at 9600.




 Data Bits [8]

Use the Data Bits option to specify the number of data bits.



7



8 D EFAULT

Sets the data bits at 7.

Sets the data bits at 8.

 Parity [None]

Use the Parity option to specify the parity bit that can be sent with the data bits for detecting the transmission errors.



None



Even

D EFAULT







Odd

Mark

Space

No parity bit is sent with the data bits.

The parity bit is 0 if the number of ones in the data bits is even.

The parity bit is 0 if the number of ones in the data bits is odd.

The parity bit is always 1. This option does not provide error detection.

The parity bit is always 0. This option does not provide error detection.

Page 61


 Stop Bits [1]

Use the Stop Bits option to specify the number of stop bits used to indicate the end of a serial data packet. Communication with slow devices may require more than 1 stop bit.



1



2

D EFAULT

Sets the number of stop bits at 1.

Sets the number of stop bits at 2.

4.3.8.2 Legacy Console Redirection Settings

The Legacy Console Redirection Settings

menu ( BIOS Menu 13 ) allows the legacy

console redirection options to be configured.


Advanced

Legacy Serial Redirection Port [COM1] Select a COM port to display redirection of

Legacy OS and Legacy

OPROM Messages

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 13: Legacy Console Redirection Settings

 Legacy Serial Redirection Port [COM1]

Use the Legacy Serial Redirection Port option to specify a COM port to display redirection of legacy OS and legacy OPROM messages. The options include:

 COM1

 COM2

D EFAULT

 COM3 (Pci Bus0, Dev0, Func0) (Disabled)

Page 62


4.3.9 USB Configuration

Use the USB Configuration

menu ( BIOS Menu 14 ) to read USB configuration

information and configure the USB settings.


Advanced

USB Configuration

USB Controllers:

1 XHCI

USB Devices:

1 Keyboard, 1 Mouse, 1 Point, 2 Hubs

Legacy USB Support [Enabled]

Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 14: USB Configuration

 USB Devices

The USB Devices Enabled field lists the USB devices that are enabled on the system

 Legacy USB Support [Enabled]

Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support. Normally if this option is not enabled, any attached USB mouse or USB keyboard does not become available until a USB compatible operating system is fully booted with all

USB drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard can control the system even when there is no USB driver loaded onto the system.

Page 63



Enabled



Disabled

D EFAULT



Auto


Legacy USB support enabled

Legacy USB support disabled

Legacy USB support disabled if no USB devices are connected

4.3.10 IEI Feature

Use the IEI Feature

menu ( BIOS Menu 15 ) to configure One Key Recovery function.


Advanced iEi Feature

Auto Recovery Function [Disabled]

Auto Recovery Function

Reboot and recover system automatically within 10 min, when OS crashes. Please install

Auto Recovery API service before enabling this funciton.

---------------------



: Select Screen

↑ ↓

: Select Item

+ - Change Opt.

F1 General Help

F2 Previous Values

F3 Optimized Defaults

F4 Save

ESC Exit


BIOS Menu 15: IEI Feature

 Auto Recovery Function [Disabled]

Use the Auto Recovery Function BIOS option to enable or disable the auto recovery function of the IEI One Key Recovery.






Enabled

Auto recovery function disabled

Auto recovery function enabled

Page 64


4.4 Chipset

Use the Chipset

menu ( BIOS Menu 16 ) to configure the system chipset.



> System Agent (SA) Configuration

> PCH-IO Configuration

System Agent (SA)

Parameters

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 16: Chipset

4.4.1 System Agent (SA) Configuration

Use the System Agent (SA) Configuration

menu ( BIOS Menu 17 ) to configure the

System Agent (SA) parameters.


Chipset

System Agent (SA) Configuration

VT-d

VT-d

> Memory Configuration

> Graphics Configuration

Supported

[Disabled]

VT-d capability

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 17: System Agent (SA) Configuration

Page 65


 VT-d [Disabled]

Use the VT-d option to enable or disable VT-d support.




Disable VT-d support.



Enabled Enable VT-d support.

4.4.1.1 Memory Configuration

Use the Memory Configuration

submenu ( BIOS Menu 18 ) to display the memory

information.


Chipset

Memory Information

Size

Number of Ranks

Manufacturer

DIMM2

DIMM1 Populated & Enabled

4096 MB (DDR4)

1

Unknown

Not Populated /Disabled

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 18: Memory Configuration

Page 66


4.4.1.2 Graphics Configuration

Use the Graphics Configuration

menu ( BIOS Menu 19 ) to configure the graphics

settings.


Chipset

Graphics Configuration

Primary Display

Internal Graphics

DVMT Pre-Allocated

DVMT Total Gfx Mem

> LCD Control

[Auto]

[Enabled]

[64M]

[MAX]

Select which of IGFX/PCIE

Graphics device should be

Primary Display.

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 19: Graphics Configuration

 Primary Display [Auto]

Use the Primary Display option to select the graphics controller used as the primary boot device. Configuration options are listed below:

 Auto

 IGFX

D EFAULT

 Internal Graphics [Enabled]

Use the Internal Graphics option to enable or disable the internal graphics device.



Auto



Disabled

The internal graphics device is automatically detected and enabled.

Disable the internal graphics device.

Page 67




Enabled D EFAULT Enable the internal graphics device. The following options/submenu appear with values that can be selected:

DVMT Pre-Allocated

DVMT Total Gfx Mem

LCD Control

 DVMT Pre-Allocated [256M]

Use the DVMT Pre-Allocated option to set the amount of system memory allocated to the integrated graphics processor when the system boots. The system memory allocated can then only be used as graphics memory, and is no longer available to applications or the operating system. Configuration options are listed below:

 32M

 64M D

EFAULT

 DVMT Total Gfx Mem [MAX]

Use the DVMT Total Gfx Mem option to select DVMT5.0 total graphic memory size used by the internal graphic device. The following options are available:

 256M

 128M

 MAX D EFAULT

Page 68


4.4.1.2.1 LCD Control

Use the LCD Control

submenu ( BIOS Menu 20 ) to select a display device which will be

activated during POST.


Chipset

LCD Control

Primary IGFX Boot Display [VBIOS Default]

Select the Video Device which will be activated during POST. This has no effect if external graphics present.

Secondary boot display selection will appear based on your selection.

VGA modes will be supported only on primary display.

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 20: LCD Control

 Primary IGFX Boot Display [VBIOS Default]

Use the Primary IGFX Boot Display option to select the display device used by the system when it boots.

 VBIOS Default

 HDMI1

 LVDS

 HDMI2

D EFAULT

Page 69


4.4.2 PCH-IO Configuration

Use the PCH-IO Configuration

menu ( BIOS Menu 21 ) to configure the PCH-IO chipset.


Chipset

PCH-IO Configuration

Auto Power Button Status

Restore AC Power Loss

Power Saving Function(ERP)

USB Power SW1

[Disable (ATX)]

[Last State]

[Disabled]

[+5V]

Select AC power state when power is re-applied after a power failure.

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

> SATA Configuration

> HD Audio Configuration

> PCI Express Configuration

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 21: PCH-IO Configuration

 Restore on AC Power Loss [Last State]

Use the Restore on AC Power Loss BIOS option to specify what state the system returns to if there is a sudden loss of power to the system.



Power Off



Power On



The system remains turned off

The system turns on

Last State D EFAULT The system returns to its previous state. If it was on, it turns itself on. If it was off, it remains off.

Page 70


 Power Saving Function(ERP) [Disabled]

Use the Power Saving Function(ERP) BIOS option to enable or reduce power consumption in the S5 state. When enabled, the system can only be powered-up using the power button.






Enabled

Power Saving Function support disabled

Power Saving Function support enabled

 USB Power SW1 [+5V]

Use the USB Power SW1 BIOS option to configure the USB power source for all of the

USB 3.0 and USB 2.0 connectors of the panel PC.



+5V



+5V DUAL

D EFAULT

Set the USB power source to +5V

Set the USB power source to +5V dual

4.4.2.1 PCI Express Configuration

Use the PCI Express Configuration

submenu ( BIOS Menu 22 ) to configure the PCI

Express slots.


Chipset

PCI Express Configuration

M2_M1 Card Selection


> M2_M1

> M2_M2

> M1

> CN2

[PCIE]

[PCIE]


Settings.

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 22: PCI Express Configuration

Page 71


 M2_M1 Card Selection / M2_M2 Card Selection [PCIE]

Use the M2_M1 Card Selection / M2_M2 Card Selection option to configure M.2 device mode.

 mSATA



PCIE

Configures M.2 slot as mSATA interface.

D EFAULT

Configures M.2 slot as PCIe interface.

The M2_M1 , M2_M2 , M1 and CN2 indicate the slots on the motherboard listed below:

 M2_M1: M.2 M-key 2242/2260/2280 slot (PCIe + SATA) with RAID

 M2_M2: M.2 M-key 2242/2260/2280 slot (PCIe + SATA) with RAID

 M2: M.2 A-/E-key 2242 slot (PCIe + USB)

 CN2: Full-size/Half-size PCIe Mini slot (PCIe + USB)

All submenus contain the following options:

 PCIe Speed [Auto]

Use the PCIe Speed option to configure the PCIe interface speed.

 Auto

 Gen 1

 Gen 2

 Gen 3

D EFAULT

 Detect Non-Compliance Device [Disabled]

Use the Detect Non-Compliance Device option to enable or disable detecting if a non-compliance PCI Express device is connected to the PCI Express slot.



Disabled



Enabled

D EFAULT Disables to detect if a non-compliance PCI

Express device is connected to the PCI Express slot.

Enables to detect if a non-compliance PCI Express device is connected to the PCI Express slot.

Page 72


4.4.2.2 SATA Configuration

Use the SATA Configuration

menu ( BIOS Menu 23 ) to change and/or set the

configuration of the SATA devices installed in the system.


Chipset

SATA Configuration

SATA Controller(s)

SATA Mode Selection

SATA1

[Enabled]

[AHCI]

Empty

Enable/Disable SATA

Device.

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select mSATA(M2_M1) mSATA(M2_M2)

Empty

Empty

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 23: SATA Configuration

 SATA Controller(s) [Enabled]

Use the SATA Controller(s) option to configure the SATA controller(s).



Enabled



Disabled

D EFAULT Enable the on-board SATA controller(s).

Disable the on-board SATA controller(s).

 SATA Mode Selection [AHCI]

Use the SATA Mode Selection option to determine how SATA devices operate.



AHCI



RAID

D EFAULT

Configures SATA devices as AHCI device.

Configures SATA devices as RAID device.

Page 73


NOTE:

Before accessing the RAID configuration utility, ensure to set the

Option ROM Messages BIOS option in the Boot menu to Force

BIOS . This is to allow the “Press <CTRL+I> to enter Configuration

Utility……” message to appear during POST. Press Ctrl+I when prompted to enter the RAID configuration utility.

NOTE:

1. For the Windows 7 user, please install the Intel® RAID driver.

2. In case of the need of RAID surveillance function, please complete the .Net Framework 4.5 installation and download the Intel® RAID management software from the Intel® website: https://downloadcenter.intel.com/zh-tw/product/55005/Intel-Intel-RST.

Page 74


4.4.2.3 HD Audio Configuration

Use the HD Audio Configuration

submenu ( BIOS Menu 24 ) to configure the High

Definition Audio codec.


Chipset

HD Audio Configuration

HD Audio [Enabled]

Control Detection of the

HD-Audio device.

Disable = HDA will be unconditionally disabled

Enabled = HDA will be unconditionally enabled.

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 24: HD Audio Configuration

 HD Audio [Enabled]

Use the HD Audio BIOS option to enable or disable the High Definition Audio controller.



Disabled



Enabled

The High Definition Audio controller is disabled.

D EFAULT The High Definition Audio controller is enabled.

Page 75


4.5 Security

Use the Security

menu ( BIOS Menu 25 ) to set system and user passwords.



Password Description

If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup.

If ONLY the User’s password is set, then this is a power on password and must be entered to

Set Administrator

Password boot or enter Setup. In Setup the User will have Administrator rights.

The password must be

In the following range:

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

Maximum length

Minimum length

Administrator Password

3

20

+/-: Change Opt.

F1: General Help

F2: Previous Values


User Password

F4: Save & Exit

ESC: Exit


BIOS Menu 25: Security

 Administrator Password

Use the Administrator Password field to set or change an administrator password.

 User Password

Use the User Password field to set or change a user password.

Page 76


4.6 Boot

Use the Boot

menu ( BIOS Menu 26 ) to configure system boot options.



Boot Configuration

Bootup NumLock State

Quiet Boot

UEFI Boot

Driver Option Priorities

Launch PXE OpROM

[On]

[Enabled]

[Disabled]

Select the keyboard

NumLock state

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

Option ROM Messages

Boot Option Priorities

[Disabled]

[Force BIOS]

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 26: Boot

 Bootup NumLock State [On]

Use the Bootup NumLock State BIOS option to specify if the number lock setting must be modified during boot up.



On D EFAULT



Off

Allows the Number Lock on the keyboard to be enabled automatically when the computer system boots up. This allows the immediate use of the

10-key numeric keypad located on the right side of the keyboard. To confirm this, the Number Lock LED light on the keyboard is lit.

Does not enable the keyboard Number Lock automatically. To use the 10-keys on the keyboard, press the Number Lock key located on the upper left-hand corner of the 10-key pad. The Number

Lock LED on the keyboard lights up when the

Number Lock is engaged.

Page 77


 Quiet Boot [Enabled]

Use the Quiet Boot BIOS option to select the screen display when the system boots.



Disabled




Normal POST messages displayed

OEM Logo displayed instead of POST messages

 UEFI Boot [Disabled]

Use the UEFI Boot BIOS option to enable or disable UEFI boot.



Enabled




Enable UEFI boot if the 1 st

boot device is a GPT

HDD.

Disable UEFI boot.

 Launch PXE OpROM [Disabled]

Use the Launch PXE OpROM option to enable or disable boot option for legacy network devices.






Enabled

Ignore all PXE Option ROMs

Load PXE Option ROMs

 Option ROM Messages [Force BIOS]

Use the Option ROM Messages option to set the Option ROM display mode.



Force

BIOS



Keep

Current

D

EFAULT

Sets display mode to force BIOS.

Sets display mode to current.

Page 78


4.7 Save & Exit

Use the Save & Exit

menu ( BIOS Menu 27 ) to load default BIOS values, optimal failsafe

values and to save configuration changes.



Save Changes and Reset

Discard Changes and Reset

Restore Defaults

Save as User Defaults

Restore User Defaults

Reset the system after saving the changes.

---------------------



: Select Screen

↑ ↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values


F4: Save & Exit

ESC: Exit


BIOS Menu 27: Save & Exit

 Save Changes and Reset

Use the Save Changes and Reset option to save the changes made to the BIOS options and reset the system.

 Discard Changes and Reset

Use the Discard Changes and Reset option to exit the system without saving the changes made to the BIOS configuration setup program.

 Restore Defaults

Use the Restore Defaults option to load the optimal default values for each of the parameters on the Setup menus. F3 key can be used for this operation.

Page 79


 Save as User Defaults

Use the Save as User Defaults option to save the changes done so far as user defaults.

 Restore User Defaults

Use the Restore User Defaults option to restore the user defaults to all the setup options.

Page 80


Chapter

5

5

Driver Installation

Page 81


5.1 Available Drivers

All the drivers for the POCm-W22/24C-ULT3 are available on IEI Resource Download

Center ( https://download.ieiworld.com

). Type POCm-W22C-ULT3 or POCm-W24C-ULT3, and press Enter to find all the relevant software, utilities, and documentation.

Figure 5-1: IEI Resource Download Center

5.2 Driver Download

To download drivers from IEI Resource Download Center, follow the steps below.

Step 1: Go to https://download.ieiworld.com

. Type POCm-W22C-ULT3 or

POCm-W24C-ULT3, and press Enter.

Step 2: All product-related software, utilities, and documentation will be listed. You can choose Driver to filter the result.

Page 82


Step 3: Click the driver file name on the page and you will be prompted with the following window. You can download the entire ISO file (



), or click the small arrow to find an individual driver and click the file name to download (



).

NOTE:

To install software from the downloaded ISO image file in Windows 8,

8.1 or 10, double-click the ISO file to mount it as a virtual drive to view its content. On Windows 7 system, an additional tool (such as Virtual

CD-ROM Control Panel from Microsoft) is needed to mount the file.

Page 83


5.3 Intel® Chipset Driver

To install the chipset driver, please follow the steps below.

Step 1: Navigate to the Chipset folder downloaded from IEI website.

Step 2: Double click the setup file in the folder. The Intel® Chipset Device Software installation wizard appears.

Figure 5-2: Intel® Chipset Device Software Installation Wizard

Step 3: Follow the step-by-step instruction of the installation wizard to install the driver.

Step 0:

Page 84


5.4 Intel® Graphics Driver

To install the graphics driver, please follow the steps below.

Step 1: Navigate to the VGA folder downloaded from IEI website. Locate the driver setup file for the corresponding operating system.

Step 2: Double click the setup file in the folder. The Intel® Graphics Driver installation wizard

appears ( Figure 5-3 ).

Figure 5-3: Intel® Graphics Driver Installation Wizard

Step 3: Follow the step-by-step instruction of the installation wizard to install the graphics driver.

Step 0:

Page 85


5.5 Audio Driver

To install the driver for the speaker and the microphone, please follow the steps below.

Step 1: Navigate to the Audio folder downloaded from IEI website.

Step 2: Double click the setup file in the folder. The InstallShield Wizard screen

appears ( Figure 5-4 ).

Figure 5-4: Realtek HD Audio Driver InstallShield Wizard

Step 3: Follow the step-by-step instruction of the installation wizard to install the HD

Audio driver.

Step 0:

Page 86


5.6 LAN Driver

To install the LAN driver, please follow the steps below.

Step 1: Select Lan from the list of the driver menu. Locate the driver setup file for the corresponding operating system.

Step 2: Double click the setup file in the folder. The Install Wizard screen appears

( Figure 5-4 ).

Figure 5-5: LAN Driver Installation Wizard

Step 3: Follow the step-by-step instruction of the installation wizard to install the Intel®

Network Connection driver.

Step 0:

Page 87

5.7 Intel® Management Engine


To install the Intel® Management Engine Components, please follow the steps below.

Step 1: Navigate to the ME folder downloaded from IEI website. Locate the driver setup file.

Step 2:

Double click the setup file. The installation wizard window appears ( Figure 5-3 ).

Figure 5-6: Intel® ME Components Installation Wizard

Step 3: Follow the step-by-step instruction of the installation wizard to install the Intel®

Management Engine Components.

Step 0:

Page 88


5.8 Wireless LAN Driver

To install the wireless LAN driver, please follow the steps below.

Step 1: Navigate to the Intel AC8265 (Wifi+BT) folder downloaded from IEI website.

Locate the driver setup file for the corresponding operating system in the Wifi driver folder.

Step 2: Double click the setup file in the folder, and then select the language for the

installation. The InstallShield Wizard screen appears ( Figure 5-7 ).

Figure 5-7: Wireless LAN InstallShield Wizard

Step 3: Check to agree the End User License Agreement and click Install . Follow the step-by-step instruction of the installation wizard to install the Wireless LAN driver.

Step 0:

Page 89


5.9 Bluetooth Driver

To install the Bluetooth driver, please follow the steps below.

Step 1: Navigate to the Intel AC8265 (Wifi+BT) folder downloaded from IEI website.

Locate the BT driver setup file for the corresponding operating system in the BT driver folder.

Step 2: Double click the setup file in the folder. The InstallShield Wizard screen appears

( Figure 5-8 ).

Figure 5-8: Bluetooth Driver InstallShield Wizard

Step 3: Follow the step-by-step instruction of the installation wizard to install the

Bluetooth driver.

Step 0:

Page 90


5.10 RFID Driver (Optional)

To install the RFID driver, please follow the steps below.

Step 1: Open the Device Manager window. Long press or right click USB <-> Serial .

Select Update Driver Software from the pop-up window.

Figure 5-9: Device Manager - Update Driver Software

Step 2: The Update Driver Software window appears. Select Browse my computer for driver software .

Page 91


Figure 5-10: Update Driver Software Window

Step 3: The following window appears. Press/Click the Browse button to specify the

RFID driver directory (\11.RFID\D490). Then, press/click the Next button.

Figure 5-11: Browse for Driver Software Window

Step 4: The system starts installing the RFID driver.

Step 5: After the driver installation process is complete, a confirmation screen appears.

Click Close to exit the program.

Page 92


Figure 5-12: Driver Installation Complete Window

Step 6: Repeat Step 1 ~ Step 5 to install the RFID driver again.

Step 7: The Device Manager Window now shows the installed RFID devices.

Step 0:

Figure 5-13: Device Manager Window – RFID Devices

Page 93


Appendix

A

A

Regulatory Compliance

Page 94


DECLARATION OF CONFORMITY

This equipment is in conformity with the following EU directives:

 EMC Directive (2004/108/EC, 2014/30/EU)

 Low-Voltage Directive (2006/95/EC, 2014/35/EU)

 RoHS II Directive (2011/65/EU, 2015/863/EU)

 Medical Device Directive 93/42/EEC: EN 60601-1

If the user modifies and/or install other devices in the equipment, the CE conformity declaration may no longer apply.

If this equipment has telecommunications functionality, it also complies with the requirements of the Radio Equipment Directive 2014/53/EU.

English

IEI Integration Corp declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.

Български [Bulgarian]

IEI Integration Corp. декларира, че този оборудване е в съответствие със съществените изисквания и другите приложими правила на Директива 2014/53/EU

.

Česky [Czech]

IEI Integration Corp tímto prohlašuje, že tento zařízení je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 2014/53/EU.

Dansk [Danish]

IEI Integration Corp erklærer herved, at følgende udstyr overholder de væsentlige krav o

øvrige relevante krav i direktiv 2014/53/EU.

Deutsch [German]

IEI Integration Co p, erklärt dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 2014/53/EU.

Eesti [Estonian]

IEI Integration Corp deklareerib seadme seadme vastavust direktiivi 2014/53/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

Page 95


Español [Spanish]

IEI Integration Corp declara que el equipo cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 2014/53/EU.

Ελληνική [Greek]

IEI Integration Corp ΔΗΛΩΝΕΙ ΟΤΙ ΕΞΟΠΛΙΣΜΟΣ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ

ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ

2014/53/EU.

Français [French]

IEI Integration Corp déclare que l'appareil est conforme aux exigences ssentielles et aux autres dispositions pertinentes de la directive 2014/53/EU.

Italiano [Italian]

IEI Integration Corp dichiara che questo apparecchio è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 2014/53/EU.

Latviski [Latvian]

IEI Integration Corp deklarē, ka iekārta atbilst būtiskajām prasībām un citiem ar to saistītajiem noteikumiem Direktīvas 2014/53/EU.

Lietuvių [Lithuanian]

IEI Integration Corp deklaruoja, kad šis įranga atitinka esminius reikalavimus ir kitas

2014/53/EU Direktyvos nuostatas.

Nederlands [Dutch]

IEI Integr tion Corp dat het toestel toestel in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 2014/53/EU.

Malti [Maltese]

IEI Integration Corp jiddikjara li dan prodott jikkonforma malħ ti ġ ijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid

-Dirrettiva 2014/53/EU.

Magyar [Hungarian]

IEI Integration Corp nyilatkozom, hogy a berendezés megfelel a vonatkozó alapvetõ követelményeknek és az 2014/53/EU irányel egyéb elõírásainak.

Polski [Polish]

IEI Integration Corp oświadcza, że wyrobu jest zgodny z zasadn iczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 2014/53/EU.

Português [Portuguese]

IEI Integration Corp declara que este equipamento está conforme com os requisitos essenciais e outras disposições da Directiva 2014/53/EU.

Page 96


Româna [Romanian]

IEI Integration Corp declară că acest echipament este in conformitate cu cerinţele esenţiale şi cu celelalte prevederi relevante ale Directivei 2014/53/EU.

Slovensko [Slovenian]

IEI Integration Corp izjavlja, da je ta opreme v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 2014/53/EU.

Slovensky [Slovak]

IEI Integration Corp týmto vyhlasuje, že zariadenia spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 2014/53/EU.

Suomi [Finnish]

IEI Integration Corp vakuuttaa täten että laitteet on direktiivin 2014/53/EU oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Svenska [Swedish]

IEI Integration Corp förklarar att denna utrustnin styp står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv

2014/53/EU.

FCC WARNING

This equipment complies with part 18 of the FCC Rules.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:







Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Page 97


ROHS STATEMENT

The label on the product indicates this product conforms to European (EU) Restriction of

Hazardous Substances (RoHS) that set maximum concentration limits on hazardous materials used in electrical and electronic equipment.

CHINA ROHS

The label on the product indicates the estimated “Environmentally Friendly Use Period”

(EFUP). This is an estimate of the number of years that these substances would “not leak out or undergo abrupt change.” This product may contain replaceable sub-assemblies/components which have a shorter EFUP such as batteries and lamps.

These components will be separately marked.

Page 98


Appendix

B

B

Product Disposal

Page 99


CAUTION:

Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery.

Dispose of used batteries according to instructions and local regulations.

 Outside the European Union - If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method.

 Within the European Union–The device that produces less waste and is easier to recycle is classified as electronic device in terms of the European

Directive 2012/19/EU (WEEE), and must not be disposed of as domestic garbage.

EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. This includes monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your display products, please follow the guidance of your local authority, or ask the shop where you purchased the product.

The mark on electrical and electronic products only applies to the current European Union

Member States.

Please follow the national guidelines for electrical and electronic product disposal.

Page 100


Appendix

C

C

Maintenance and

Cleaning Precautions

Page 101


When maintaining or cleaning the POCm-W22/24C-ULT3, please follow the guidelines below.

WARNING:

If you dropped any material or liquid such as water onto the panel PC when cleaning, unplug the power cable immediately and contact your dealer or the nearest service center. Always make sure your hands are dry when unplugging the power cable.

CAUTION:

 For safety reasons, turn-off the power switch and unplug the panel

PC before cleaning.

 Do not scratch or rub the screen with a hard object.

 Never use any of the following solvents on the medical panel PC.

Harsh chemicals may cause damage to the cabinet and the touch sensor.

Thinner Spray-type cleaner, Benzene, Wax, Abrasive cleaner,

Acid or Alkaline solvent.

C.1.1 Maintenance and Cleaning

Prior to cleaning any part or component of the POCm-W22/24C-ULT3, please read the details below.

 To clean the POCm-W22/24C-ULT3, o remove dirt with a lightly moistened cloth. Then wipe the external chassis with a soft dry cloth. o use 75% ethanol alcohol to clean the external chassis.

 Cleaning frequency: follow the cleaning method guidelines of the hospital.

 Except for the LCD panel, never spray or squirt liquids directly onto any other components.

 The interior of the POCm-W22/24C-ULT3 does not require cleaning. Keep fluids away from the POCm-W22/24C-ULT3 interior.

Page 102


 Never drop any objects or liquids through the openings of the

POCm-W22/24C-ULT3.

C.1.2 Cleaning Tools

Some components in the POCm-W22/24C-ULT3 may only be cleaned using a product specifically designed for the purpose. In such case, the product will be explicitly mentioned in the cleaning tips. Below is a list of items to use when cleaning the

POCm-W22/24C-ULT3.

 Cloth – Although paper towels or tissues can be used, a soft, clean piece of cloth is recommended when cleaning the POCm-W22/24C-ULT3.

 Water/Ethanol alcohol – A cloth moistened with water or 75% ethanol alcohol can be used to clean the POCm-W22/24C-ULT3.

 Using solvents – The use of solvents is not recommended when cleaning the

POCm-W22/24C-ULT3 as they may damage the plastic parts.

 Cotton swabs - Cotton swaps moistened with water are excellent tools for wiping hard to reach areas.

 Foam swabs - Whenever possible, it is best to use lint free swabs such as foam swabs for cleaning.

Page 103


Appendix

D

D

Symbol Definitions

Page 104


The following symbols appear on the product, its labeling, or the product packing. Each symbol carries a special definition, as defined below:

Direct current

This side up

Consult the operating instructions

Fragile, handle with care

Keep dry

Refer to instruction manual

Indicates the manufacturer

Indicates proof of conformity to applicable European Economic Community

Council directives and to harmonized standards published in the official journal of the European Communities.

Tested to comply with FCC Class B standard.

This symbol indicates that the waste of electronic equipment must not be disposed as unsorted municipal waste and must be collected separately.

Please contact the manufacturer or other authorized disposal company to decommission your equipment.

This product is recyclable.

Page 105


Appendix

E

E

BIOS Menu Options

Page 106


 System Date [xx/xx/xx] ........................................................................................................ 48

 System Time [xx:xx:xx] ....................................................................................................... 48

 Intel (VMX) Virtualization Technology [Disabled] ............................................................. 49

 Active Processor Cores [All] .............................................................................................. 49

 Hyper-Threading [Enabled] ................................................................................................. 50

 Intel

®

SpeedStep(tm) [Enabled] .......................................................................................... 50

 CPU C State [Disabled] ........................................................................................................ 50

 AMT BIOS Features [Enabled] ............................................................................................ 51

 Unconfigure ME [Disabled] ................................................................................................. 51

 Security Device Support [Disable] ..................................................................................... 52

 ACPI Sleep State [S3 (Suspend to RAM)] .......................................................................... 53

 Serial Port [Enabled] ............................................................................................................ 55

 Change Settings [Auto] ....................................................................................................... 55

 Device Mode [RS232] ........................................................................................................... 55

 Serial Port [Enabled] ............................................................................................................ 56

 Change Settings [Auto] ....................................................................................................... 56

 Device Mode [RS232] ........................................................................................................... 57

 PC Health Status .................................................................................................................. 57

 Wake System with Fixed Time [Disabled] ......................................................................... 58

 Console Redirection [Disabled] ......................................................................................... 60

 Terminal Type [ANSI] ........................................................................................................... 60

 Bits per second [115200] ..................................................................................................... 61

 Data Bits [8] .......................................................................................................................... 61

 Parity [None] ......................................................................................................................... 61

 Stop Bits [1] .......................................................................................................................... 62

 Legacy Serial Redirection Port [COM1] ............................................................................. 62

 USB Devices ......................................................................................................................... 63

 Legacy USB Support [Enabled] .......................................................................................... 63

 Auto Recovery Function [Disabled] ................................................................................... 64

 VT-d [Disabled] ..................................................................................................................... 66

 Primary Display [Auto] ........................................................................................................ 67

 Internal Graphics [Enabled] ................................................................................................ 67

 DVMT Pre-Allocated [256M] ................................................................................................ 68

 DVMT Total Gfx Mem [MAX] ................................................................................................ 68

 Primary IGFX Boot Display [VBIOS Default] ..................................................................... 69

Page 107


 Restore on AC Power Loss [Last State] ............................................................................ 70

 Power Saving Function(ERP) [Disabled] ........................................................................... 71

 USB Power SW1 [+5V] ......................................................................................................... 71

 M2_M1 Card Selection / M2_M2 Card Selection [PCIE] ................................................... 72

 PCIe Speed [Auto] ................................................................................................................ 72

 Detect Non-Compliance Device [Disabled] ....................................................................... 72

 SATA Controller(s) [Enabled] ............................................................................................. 73

 SATA Mode Selection [AHCI] .............................................................................................. 73

 HD Audio [Enabled] ............................................................................................................. 75

 Administrator Password ..................................................................................................... 76

 User Password ..................................................................................................................... 76

 Bootup NumLock State [On] ............................................................................................... 77

 Quiet Boot [Enabled] ........................................................................................................... 78

 UEFI Boot [Disabled] ........................................................................................................... 78

 Launch PXE OpROM [Disabled] ......................................................................................... 78

 Option ROM Messages [Force BIOS] ................................................................................. 78

 Save Changes and Reset .................................................................................................... 79

 Discard Changes and Reset ............................................................................................... 79

 Restore Defaults .................................................................................................................. 79

 Save as User Defaults ......................................................................................................... 80

 Restore User Defaults ......................................................................................................... 80

Page 108


Appendix

F

F

Watchdog Timer

Page 109


NOTE:

The following discussion applies to DOS. Contact IEI support or visit the IEI website for drivers for other operating systems.

The Watchdog Timer is a hardware-based timer that attempts to restart the system when it stops working. The system may stop working because of external EMI or software bugs.

The Watchdog Timer ensures that standalone systems like ATMs will automatically attempt to restart in the case of system problems.

A BIOS function call (INT 15H) is used to control the Watchdog Timer.

INT 15H:

AH – 6FH Sub-function:

AL – 2: Sets the Watchdog Timer’s period.

BL: Time-out value (Its unit-second is dependent on the item “Watchdog

Timer unit select” in CMOS setup).

Table F-1: AH-6FH Sub-function

Call sub-function 2 to set the time-out period of Watchdog Timer first. If the time-out value is not zero, the Watchdog Timer starts counting down. When the timer value reaches zero, the system resets. To ensure that this reset condition does not occur, calling sub-function

2 must periodically refresh the Watchdog Timer. However, the watchdog timer is disabled if the time-out value is set to zero.

A tolerance of at least 10% must be maintained to avoid unknown routines within the operating system (DOS), such as disk I/O that can be very time-consuming.

Page 110


NOTE:

The Watchdog Timer is activated through software. The software application that activates the Watchdog Timer must also deactivate it when closed. If the Watchdog Timer is not deactivated, the system will automatically restart after the Timer has finished its countdown.

EXAMPLE PROGRAM:

; INITIAL TIMER PERIOD COUNTER

;

W_LOOP:

;

MOV

MOV

INT 15H

AX, 6F02H

BL, 30

;setting the time-out value

;time-out value is 48 seconds

;

; ADD THE APPLICATION PROGRAM HERE

;

CMP

JNE

EXIT_AP, 1

W_LOOP

;is the application over?

;No, restart the application

MOV

MOV

INT 15H

AX, 6F02H

BL, 0 ;

;disable Watchdog Timer

;

; EXIT ;

Page 111


Appendix

G

G

Hazardous Materials

Disclosure

Page 112


The details provided in this appendix are to ensure that the product is compliant with the

Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China

RoHS only.

A label will be placed on each product to indicate the estimated “Environmentally Friendly

Use Period” (EFUP). This is an estimate of the number of years that these substances would “not leak out or undergo abrupt change.” This product may contain replaceable sub-assemblies/components which have a shorter EFUP such as batteries and lamps.

These components will be separately marked.

Please refer to the following table.

Part Name Toxic or Hazardous Substances and Elements

Lead

(Pb)

Mercury

(Hg)

Cadmium

(Cd)

Hexavalent

Chromium

(CR(VI))

Polybrominated

Biphenyls

(PBB)

Polybrominated

Diphenyl Ethers

(PBDE)

Housing

Display

Printed Circuit

Board

Metal Fasteners

Cable Assembly

Fan Assembly

Power Supply

Assemblies

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

Battery O O O O O O

O: This toxic or hazardous substance is contained in all of the homogeneous materials for the part is below the limit requirement in SJ/T11363-2006 (now replaced by GB/T 26572-2011).

X: This toxic or hazardous substance is contained in at least one of the homogeneous materials for this part is above the limit requirement in SJ/T11363-2006 (now replaced by GB/T 26572-2011).

Page 113


此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符

合中国 RoHS 标准规定的限量要求。

本产品上会附有 ” 环境友好使用期限 ” 的标签，此期限是估算这些物质 ” 不会有泄漏或突变 ” 的

年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元

件将会单独标示出来。

部件名称有毒有害物质或元素

铅

(Pb)

汞

(Hg)

镉

(Cd)

六价铬

(CR(VI))

多溴联苯

(PBB)

多溴二苯

醚

(PBDE)

壳体 O O O O O O

显示

印刷电路板

金属螺帽

O

O

O

O

O

O

O

O

O

O

O

O

O O O O O O

电缆组装 O O O O O O

风扇组装

电力供应组装

电池

O

O

O

O

O

O

O

O

O

O

O

O

O O O O O O

O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T 11363-2006 ( 现由 GB/T 26572-2011 取代 )

标准规定的限量要求以下。

X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 ( 现由 GB/T

26572-2011 取代 ) 标准规定的限量要求。

Page 114

No results