EcoFasten Clickfit Manual

RAPID

INSTALLATION,

HIGH-QUALITY SOLAR

MOUNTING SYSTEM

FOR SHINGLE AND

TILE ROOFS

VERSION: 2.0

TABLE OF CONTENTS

Subject Page #

Introduction 3

Product Description 4

Ratings 5

System Components

Required Tools

Array Layout

Installing ClickFit

8

9

6

7

Flashing and L feet

Installing Tile Hooks

Tile Hook Sub-Flashing

Installing the Rail

10

11

12

13

Module Installation

Bonding and Grounding

MLPE Clip Intallation

UL2703 Certified Modules

Clamp Tables

14 - 17

18 - 19

20

21-29

30

2

REV DATE: 07/16/2020

INTRODUCTION

1.0 Introduction

This manual describes the installation of the ClickFit mounting system for photovoltaic modules on steepslope roofs. Described within are details for composition shingle and tile, attachments for ClickFit for other roof types are available at www.EcoFastenSolar.com.

All installation manuals are available for download at www.EcoFastenSolar.com.

2.0 General Installation Conditions

2.1 General

Failure to observe the requirements in this document can lead to the exclusion of all guarantees and product liability. EcoFasten Solar reserves the right to amend this document without prior notice.

2.2 Stability and Condition of the Roof

The roof must be in good condition and strong enough to support the weight of the modules, including the additional equipment, wind and snow loads. When in doubt, consult with the engineer of record, and/or the local building inspector.

2.3 Application Range of ClickFit

• Refer to Compatibility module list on page 21.

• Please refer to the Ecofasten ClickFit span tables for system structural certification and allowable spans.

2.4 Warranty

Guarantee according to the warranty conditions and general terms and conditions of EcoFasten Solar. These conditions can be found on the website at www.EcoFastenSolar.com.

2.5 Liability

EcoFasten Solar cannot accept any liability whatsoever for damage or injury caused by not taking adequate safety precautions or (accurately) following the instructions given, or resulting from negligence during the installation of the product and any corresponding accessories specified in this document.

*Printing errors reserved

VERSION: 2.0

3

REV DATE: 07/16/2020

PRODUCT DESCRIPTION

The ClickFit mounting system consists of patented adjustable tile hooks and L feet, rails, and the installation materials required for the mounting of photovoltaic modules on composition shingle or tile roofs. For simplicity, tile hooks and L feet will be referred to as

“attachments”.

3.1 Attaching to the Roof

The attachments are fastened to the rafters. Attachments are height-adjustable to level the system on uneven roof surfaces.

3.2 Attaching the Rail

The rail assembles to the attachments with a click-connector, or Clicker. The rail simply clicks into place without the use of any tools.

3.3 Attaching the modules

The modules are attached to the rails by means of mid clamps and end clamps.

Installer must review the module manufacturer’s installation manual to confirm compliance to the warranty terms and conditions.

VERSION: 2.0

4

REV DATE: 07/16/2020

RATINGS

Fire Rating**

Max System Voltage

Max Fuse Rating

Certification

Warranty

UL 2703 Markings

Roof Pitch

UL 2703 Allowable Design Load Rating

Max Module Size

Module Orientation:

Class A System Fire Rating

1500 VDC

30A

Conforms to UL STD 2703

20 Year Material and Workmanship

Product listing label is located on the rail end-caps

2:12 – 12:12

10 psf downward, 5 psf upward, and 5 psf lateral

24 sqft

Portrait or Landscape

**Class A System fire rating with Type 1 & 2 PV modules. Any module-to-roof gap is permitted, with no skirt required. This rating is applicable with any roof attachment.

NOTE: Mid Clamp, MLPE Clip, and MLPE Bracket have been evaluated for multiple use, position independent.

UL 2703 Marking Example:

TM

CLICKFIT

SYSTEM

MFG ID CODE: XXX-MM-YYYY

1234567

Conforms to UL STD 2703

Torque Specifications

Lag Screw

Component

Mid-Clamp

End-Clamp

Rail Clicker Leveling Bolt

Hook Height Bolt

Ground Lug

MLPE Clip

MLPE Mount

Torque (in-lb)

N/A

144

96

142

N/A

N/A

144

144

Notes

Fully Seat. Use visual indicator of the black EPDM ring around the bonded washer for torquing.

Pre-torqued upon delivery. Applies to Tile Hook and L-Foot/Clicker

Lightly clamp hook to flush with top of next tile row

Refer to specific ground lug manufacturer’s installation manual

VERSION: 2.0

5

REV DATE: 07/16/2020

VERSION: 2.0

SYSTEM COMPONENTS

1) ClickFit Rail

1500033 (2130mm)

1500034 (3166mm)

1500035 (4202mm)

2) Rail Splice

1008061

3) CF Tile Hook and L foot

1500005 - Tile Hook

1500004 - L foot

4) CF End Clamp

See Section 10

5) CF End Cap

1510041 (Black)

1510042 (Grey)

6) CF Mid Clamp

See Section 10

7) MLPE Mount

1510057

8) MLPE Clip (RockIt Clip 2.0)

9) Module Jumper

1500028

6

REV DATE: 07/16/2020

REQUIRED TOOLS

Checklist of tools and accessories

Note: *Proper PPE shall be worn at all times*

VERSION: 2.0

Tape measure

Roof crayon or chalk (a chalk line can be helpful as well)

Cordless drill with torque adjustment and the following bits:

• 1/2” Hex socket

• 1/4” diameter drill bit. (Drilling length no less than lag bolt depth)

Brush for clearing debris from roof surface. Hint: Leaf blowers work well to remove any leftover moisture prior to installation.

Torque wrench capable of 0-150 in-lbs

7

REV DATE: 07/16/2020

ARRAY LAYOUT

• Refer to span tables, local jurisdiction, or engineer of record specifications when determining setbacks from roof edges, attachment spans, etc.

• Mark the perimeter and corners of the array on the roof surface.

*Add 3/4” to account for the gap between modules in each direction*

• Draw or snap chalk lines where the rails will be installed,(refer to module manufacturer specs to determine allowable mounting locations).

• Locate rafters within the area of the array. It may be necessary to shift the array East or West on the roof in order to fall within the rail cantilever specs (l/3) of span).

• Stagger rafters every row if required by the local jurisdiction, engineer of record, or company policy.

VERSION: 2.0

8

REV DATE: 07/16/2020

INSTALLING CLICKFIT

Pre-installing rail splices

1. Determine the number of rails required per row of modules.

2. Insert a rail splice into one rail. *Do not push it past the center bump.*

3. Slide the next rail onto the rail splice until the two rail ends meet.

4. Repeat steps 2 and 3 until the desired length is achieved. *This is usually easiest to do from the ground.*

VERSION: 2.0

9

REV DATE: 07/16/2020

FLASHING AND L FEET

Installation of flashing and L feet

• ClickFit for comp shingle roofs uses EcoFasten Solar’s GFl watertight flashing system

• Other roof types may use different EcoFasten Solar attachments, see www.EcoFastenSolar.com for more information.

Installation Steps:

1. Locate rafter lines from section 5.2.

2. Drill l/4” pilot holes at all attachment points and back fill using roof-compatible sealant.

3. Separate shingles where flashing is to be installed. Insert the flashing so the top portion is under the next row of shingles North. Ensure the flashing is pushed to the third-course of shingle to prevent water infiltration through the vertical joints between shingles.

4. Align GFl flashing hole with pilot hole. Insert the lag bolt with pre-installed bonded washer through the L foot and EPDM grommet. Tighten the lag bolt until a ring of EPDM is visible around the circumference of the bonded washer.

Tighten the lag until fully seated. The EPDM Ring visual indicator is the most effective way to ensure a watertight seal.

VERSION: 2.0

*Note the orientation of the L foot and Clicker. The two

Clicker “arms” should be facing downslope*

10

REV DATE: 07/16/2020

INSTALLING TILE HOOKS

1. Locate rafters on the roof, mark the tiles to be removed. Hint: In some cases rafter tails are visible at the eaves of the roof, making it easy to find the rough location of the rafters. In other cases, the fascia board may have nail heads visible where it was attached to the rafters. In the worst-case a row of tiles may need to be moved to determine the rafter locations.

2. Slide the tile at the desired location upward to expose the roof sub surface. If the tile is to be notched, or if using a replacement flashing, remove it entirely. Clean the sub surface with a brush to remove any debris that could affect the sealing.

3. Locate the rafter center and mark it.

4. Place the tile hook with the hook itself in the valley of the next tile below. Drill one l/4” pilot hole in the rafter center, taking care to keep the hook in the valley of the tile below. Backfill this hole with a roof- compatible sealant. For flat tiles, try to avoid having the hook land directly under a joint between tiles, this will create a larger gap or more notching than necessary.

5. Install one 5/16” x 4” lag screw on the row of holes closest to the tile hook arm. If possible, install the screw in one of the three holes directly next to the arm. If the lag screw must be installed in one of the seven holes furthest from the arm (denoted by the red rectangle below), install three deck screws in the pattern shown by the green circles below.

6. Adjust the height of the tile hook as necessary using the bolt shown in the fourth image.

7. Flash the surrounding area and lag screw head with roof-compatible sealant as necessary. Refer to Tile

Hook Subflashing Installation guide on the next page.

8. Replace the tile that was moved and/or removed, or install the tile replacement flashing. If it is to be notched, mark the tile for notching. Notching can be done with a grinding wheel or by using a chisel.

5.

6.

VERSION: 2.0

11

REV DATE: 07/16/2020

TILE HOOK SUB-FLASHING

CLICKFIT TILE HOOK SUB-FLASHING INSTALLATION STEPS:

Tools Required: Caulking gun, roofing mastic applicator

Materials Required: Roofing mastic, reinforcing fabric, roof sealant

Apply a continuous line of the roofing manufacturer’s approved sealant on the underside of the ClickFit tile hook sub-flashing to form a U-shape around the raised edges.

Lower the sub-flashing over the tile hook base. It may be necessary to move adjacent tiles to easily lower the sub-flashing onto the roof deck.

Place the sub-flashing over the base of the tile hook so the flashing covers the entire base.

EcoFasten recommends following the TRI guidelines three-course sealing method. Start the three-course sealing method by applying a layer of roofing mastic over the edges of the tile hook sub-flashing.

Place strips of reinforcing fabric over mastic to cover approximately 2” from the edge of the sub-flashing in both directions. Place strips on the side first, then the top edge.

VERSION: 2.0

Apply a final layer of mastic to completely cover the reinforcing fabric. The flashing is now installed and sealed.

REV DATE: 07/16/2020

INSTALLING THE RAIL

1. Place the rail in the Clickers.

2. Ensure the rails extend a minimum of 2” past the last attachments in each row and that each rail is aligned with the next row North and/or South.

3. Roll the rail into each Clicker, an audible “click” should be heard. If attachments are extremely misaligned it may be necessary to loosen the leveling bolt, snap the Clicker onto the rail, then re-tighten the leveling bolt to 142 in-lbs.

4. Level the rail if necessary by loosening the bolt attaching the Clicker to the L foot or tile hook.

*Ensure the tab on the Clicker is aligned with the rail edge as shown below*

VERSION: 2.0

13

REV DATE: 07/16/2020

MODULE INSTALLATION

1. Install the end clamps on each rail on whatever end you are starting with.

• Snap the end clamp onto the rail.

• Slide the end cap onto the rail.

• Turn the leg of the end clamp around the cap.

2. Place the module on the rail.

*Ensure module junction box is up-slope.*

3. Slide the module to the end clamp and align it with the array corners. Tighten the end clamp to 96 in-lb.

VERSION: 2.0

14

REV DATE: 07/16/2020

MODULE INSTALLATION

6.6 Installing additional modules on the rail

1. Click a mid clamp onto each rail.

2. Slide the mid clamps until they are flush with the side of the existing module.

3. Place and slide the next module firmly against the mid clamps. Align the bottom edges of the modules. Tighten mid clamps to 144 in-lb.

VERSION: 2.0

15

REV DATE: 07/16/2020

MODULE INSTALLATION

6.7 INSTALLING END CLAMPS AT THE END OF A ROW

1. Install the last mid clamps in the row.

2. Measure the rails from the last mid clamp to the module width plus l”.

3. Cut the rails at this mark. There is some adjustment in the end cap/clamp so it does not need to be a perfect cut.

4. Install end clamps and end caps, tighten to 96 in-lb

Alternative method:

1. Install the last module in the row, tighten the mid clamps.

2. Using a circular saw with a metal blade, or carefully with a reciprocating saw, cut the rail approximately l” past the edge of the last module.

3. Install end clamps and end caps, tighten to 96 in-lb

VERSION: 2.0

16

REV DATE: 07/16/2020

MODULE INSTALLATION

6.8 Installing additional rows of modules

1. Place the first module of the next row against the end clamps.

2. Temporarily place a mid clamp in the N-S gap between rows of modules, slide the modules up to the mid clamp as shown below.

3. Once the modules are aligned tighten the end clamps.

4. Install Dynobond clip on the bottom lip of the module frames to bond rows together.

5. Repeat steps 6.5-6.7 until the array is complete.

VERSION: 2.0

17

REV DATE: 07/16/2020

BONDING AND GROUNDING

Bonding Paths

All bond paths are carried either module-to-module through the mid clamp, or module-to- module through the module jumper shown below (bond paths shown in green):

1 ground lug per continuous array

VERSION: 2.0

18

REV DATE: 07/16/2020

7.2 Grounding

GROUNDING LUG INSTALL

BONDING AND GROUNDING

Install ground lug on the module per ground lug and module manufacturer’s instructions

NECESSARY COMPONENTS:

On of the following ground lugs (or any UL 2703 compliant ground lug):

• BurndyCL50-1TN Ground Lug (UL 2703 - E3514343 / UL 467-E9999)

• ILSCO SGB-4 Ground Lug (UL 2703 - E354420 I UL 467 - E34440)

• ILSCOGBL-40BT(UL2703 - E354420 I UL467 - E34440l

• ILSCO GBL-4DBTH (UL 2703 - E354420 / UL 467 - E34440)

• ILSCO GBL-455 (UL 2703 - E354420 I UL 467 - E34440)

This system needs to be grounded in accordance with the National Electrical Code, ANSI/NFPA 70.

*Copper wire should not come in direct contact with aluminum at any point on the array*

7.3 MLPE Clip Installation (Optional)

VERSION: 2.0

INSTALL MLPE CLIP ACCESSORY

• Determine mounting location of the MLPE and MLPE Clip on the module frame. Take care not to block drainage holes on the frame.

• Push the nut/bolt of the MLPE Clip so the carriage bolt head is furthest away from the stainless plate.

• Slide the bolt shaft into the slot on the MLPE mounting flange.

• Place the assembly onto the module flange, MLPE mounting flange on the far face (upper side) of the module frame flange, stainless plate on the closer face

(bottom side) of the module frame flange.

• Hold the carriage bolt into the MLPE mounting flange slot with your finger, this will keep the carriage bolt from spinning in the slot. Tighten the nut to 144 in-lbs using a

1/2” hex socket.

MLPE CLIP IS COMPATIBLE WITH:

• Enphase Products: M250-72, 250-60, M215-60, C250-72, S230, S280, IQ

6, IQ 6+, IQ, IQ7, IQ 7A, IQ 7+, IQ 7X, Q Aggregator

• SolarEdge Products: P300, P320, P340, P370, P400, P405, P485, P505,

P600, P700, P730, P800p, P800s, P850, P860

• See page 21 for compatible module list with MLPE Clip

19

REV DATE: 07/16/2020

MLPE MOUNT INTALLATION

Lower the MLPE Mount to the rail

Tilt and hook the mount around the top “dog ear” of the rail

Set the MLPE Mount flush with the top of the rail

Slide the microinverter flange between the

MLPE Mount and the serrated bolt flange

Tighten the bolt to 144 in-lbs

Repeat this process for all other microinverter and/or optimizer installations

MLPE MOUNT IS COMPATIBLE WITH:

Enphase Products: M250-72, 250-60, M215-60, C250-72, S230, S280, IQ 6, IQ 6+, IQ, IQ7, IQ 7A, IQ 7+, IQ 7X, Q Aggregator

SolarEdge Products: P300, P320, P340, P370, P400, P405, P485, P505, P600, P700, P730, P800p, P800s, P850, P860

VERSION: 2.0

20

REV DATE: 07/16/2020

UL2703 CERTIFIED MODULES

8.2 COMPATIBLE MODULE LIST

This racking system may be used to ground and/or mount a PV module complying with UL 1703 or UL 61730 only when the specific module has been evaluated for grounding and/or mounting in compliance with the included instructions.

Unless otherwise noted, “xxx” refers to the module power rating and both black and silver frames are included in the certification.

Manufacturer

AMERISOLAR

APTOS SOLAR

ASTRONERGY

SOLAR

ASUN

AUXIN

AXITEC

List of UL2703 Approved Modules

AMERISOLAR MODULES WITH 35, 40 AND 50 MM FRAMES

AS-BYXXXZ

WHERE "B" CAN BE 5 OR 6; "Y" CAN BE M, P, M27, P27, M30, OR P30; AND

"Z" CAN BE BLANK, W OR WB

APTOS MODULES WITH 35 AND 40 MM FRAMES

DNA-YY-ZZ23-XXX

WHERE "YY" CAN BE 120 OR 144; AND "ZZ" CAN BE MF OR BF

ASTRONERGY MODULES WITH 30, 35, 40, AND 45 MM FRAMES

AASMBBYYC/ZZ-XXX

WHERE “AA” CAN BE CH OR A; "BB" CAN BE 60, 66, OR 72; “YY” CAN BE

BLANK, 10 OR 12; "C" CAN M, P, M(BL), M-HC, M(BL)-HC, P-HC, M(DG), OR

M(DGT); AND “ZZ” CAN BE BLANK, HV, F-B, OR F-BH

ASUN MODULES WITH 35 AND 40 MM FRAMES

ASUN-XXX-YYZZ-AA

WHERE "YY" CAN BE 60 OR 72; "ZZ" CAN BE M,OR MH5; AND "AA" CAN BE

BLANK OR BB

AUXIN MODULES WITH 40 MM FRAMES

AXN6Y6ZAXXX

WHERE “Y” CAN BE M OR P; “Z” CAN BE 08, 09, 10, 11, OR 12; AND “A” CAN

BE F OR T

AXITEC MODULES WITH 35 AND 40 MM FRAMES

AC-XXXY/AAZZB

WHERE “Y” CAN BE M, P OR MH; “AA” CAN BE BLANK, 125- OR 156-; “ZZ”

CAN BE 54, 60, 72, 120, OR 144; “B” CAN BE S, X, V, XV, OR MX

VERSION: 2.0

21

REV DATE: 07/16/2020

UL2703 CERTIFIED MODULES

BOVIET

BYD

CANADIAN

SOLAR

CERTAINTEED

CSUN

ECOSOLARGY

ET SOLAR

FLEX

BOVIET MODULES WITH 35 AND 40MM FRAMES

BVM66AAYY-XXXBB

WHERE “AA” CAN BE 9, 10 OR 12; “YY” IS M OR P; AND “BB” CAN BE BLANK

OR

BYD MODULES WITH 35 MM FRAMES

BYDXXXAY-ZZ

WHERE “A” CAN BE M6, P6, MH OR PH; “Y” CAN BE C OR K; AND “ZZ” CAN

BE 30 OR 36

CANADIAN SOLAR MODULES WITH 30, 35 AND 40 MM FRAMES

CSBY-XXXZ

WHERE “B” CAN BE 1, 3 OR 6; “Y” CAN BE H, K, P, U, V, W, OR X; AND “Z” CAN

BE M, P, MS, PX , M-SD, P-AG, P-SD, MB-AG, PB-AG, MS-AG, OR MS-SD

CERTAINTEED MODULES WITH 35 AND 40 FRAMES

CTXXXYZZ-AA

WHERE “Y” CAN BE M, P, OR HC; “ZZ” CAN BE 00,01, 10, OR 11; AND “AA”

CAN BE 01, 02, 03, OR 04

CSUN MODULES WITH 35 AND 40 MM FRAMES

YYXXX-ZZABB

WHERE “YY” IS CSUN OR SST; “ZZ” IS BLANK, 60, OR 72; AND “A” IS BLANK, P

OR M; “BB” IS BLANK, BB, BW, OR ROOF

ECOSOLARGY MODULES WITH 35, 40, AND 50 MM FRAMES

ECOXXXYZZA-BBD

WHERE “Y” CAN BE A, H, S, OR T; “ZZ” CAN BE 125 OR 156; “A” CAN BE M OR

P; “BB” CAN BE 60 OR 72; AND “D” CAN BE BLANK OR B

ET SOLAR MODULES WITH 35, 40, AND 50 MM FRAMES

ET-Y6ZZXXXAA

WHERE “Y” CAN BE P, L, OR M; “ZZ” CAN BE 60 OR 72; AND “AA” CAN BE WB,

WW, BB, WBG, WWG, WBAC, WBCO, WWCO, WWBCO OR BBAC

FLEX MODULES WITH 35, 40, AND 50 MM FRAMES

FXS-XXXYY-ZZ;

WHERE “YY” CAN BE BB OR BC; AND “ZZ” CAN BE MAA1B, MAA1W, MAB1W,

SAA1B, SAA1W, SAC1B, SAC1W, SAD1W, SBA1B, SBA1W, SBC1B, OR SBC1W

VERSION: 2.0

22

REV DATE: 07/16/2020

UL2703 CERTIFIED MODULES

GCL

GIGAWATT

SOLAR

HANSOL

HANWHA SO-

LAR

HANWHA Q

CELLS

HELIENE

GCL MODULES WITH 35 MM AND 40 MM FRAMES

GCL-AB/YY XXX

WHERE “A” CAN BE M OR P; “B” CAN BE 3 OR 6; AND “YY” CAN BE 60, 72,

72H, OR 72DH

GIGAWATT MODULES WITH 40 MM FRAMES

GWXXXYY

WHERE “YY” CAN BE EITHER PB OR MB

HANSOL MODULES WITH 35 AND 40 FRAMES

HSXXXYY-ZZ

WHERE “YY” CAN BE PB, PD, PE, TB, TD, UB, UD, OR UE; AND “ZZ” CAN BE

AH2, AN1, AN3, AN4, HV1, OR JH2

HANWHA SOLAR MODULES WITH 40, 45, AND 50 MM FRAMES

HSLAAP6-YY-1-XXXZ

WHERE “AA” CAN BE EITHER 60 OR 72; “YY” CAN BE PA OR PB; AND “Z” CAN

BE BLANK OR B

HANWHA Q CELLS MODULES WITH 32, 35, 40, AND 42MM FRAMES

AAYY-ZZ-XXX

WHERE “AA” CAN BE Q. OR B.; “YY” CAN BE PLUS, PRO, PEAK, LINE PRO,

LINE PLUS, PLUS DUO OR PEAK DUO; AND “ZZ” CAN BE G3, G3.1, G4, G4.1,

L-G2, L-G2.3, L-G3, L-G3.1, L-G3Y, L-G4, L-G4.2, L-G4Y, LG4.2/TAA, BFR-G3,

BLK-G3, BFR-G3.1, BLK-G3.1, BFR-G4, BFR-G4.1, BFR G4.3, BLK-G4.1, G4/SC,

G4.1/SC, G4.1/TAA, G4.1/MAX, BFR G4.1/TAA, BFR G4.1/MAX, BLK G4.1/TAA,

BLK G4.1/SC, EC-G4.4, G5, G5/SC, BLK-G5, BLK-G5/SC, L-G5, L-G5.1, L-G5.2,

L-G5.2/H, L-G5.3, G6, G6/SC, G6+, BLK-G6, L-G6, L-G6.1, L-G6.2, L-G6.3,

G7, BLK-G6+, BLK-G6+/AC, BLK-G6+/SC, BLK-G7, G7.2, G8, BLK-G8, G8+,

BLK-G8+ L-G7, L-G7.1, L-G7.2, L-G7.3, L-G8, L-G8.1, L-G8.2, L-G8.3, L-G8.3/

BFF, L-G8.3/BFG, ML-G9 OR XL-G9.3

HELIENE MODULES WITH 40 MM FRAMES

YYZZXXXA

WHERE “YY” CAN BE 36, 60, 72, OR 96; “ZZ” CAN BE M, P, OR MBLK; AND “A”

CAN BE BLANK, HOMEPV, OR BIFACIAL

VERSION: 2.0

23

REV DATE: 07/16/2020

UL2703 CERTIFIED MODULES

HT-SAAE

HYUNDAI

ITEK

JA SOLAR

JINKO

KYOCERA

LG

HT-SAAE MODULES WITH 35 AND 40 MM FRAMES

HTYY-156Z-XXX

WHERE “YY” CAN BE 60 OR 72, “Z” CAN BE M, P, M-C, P-C, M(S), M(VS), M(V),

P(V), M(V)-C, P(V)-C

HYUNDAI MODULES WITH 33, 35, 40 AND 50 MM FRAMES

HIY-SXXXZZ

WHERE “Y” CAN BE A, D, M OR S; AND “ZZ” CAN BE HG, HI, KI, MI, MF, MG, RI,

RG, RG(BF), RG(BK), SG, TI, OR TG

ITEK MODULES WITH 40 AND 50 MM FRAMES

IT-XXX-YY

WHERE “YY” CAN BE BLANK, HE, OR SE, OR SE72

JA SOLAR MODULES WITH 30, 35, 40 AND 45 MM FRAMES

JAYYZZ-BBWW-XXX/AA

WHERE “YY” CAN BE M, P, M6 OR P6; “ZZ” CAN BE BLANK, (K), (L), (R), (V),

(BK), (FA), (TG), (FA)(R), (L)(BK), (L)(TG), (R)(BK), (R)(TG), (V)(BK), (BK)(TG), OR

(L)(BK)(TG); “BB” CAN BE 48, 60, OR 72; “WW” CAN BE D09, S01, S02, S03,

S06, S09, S10, OR S12; AND “AA” CAN BE BP, MP, SI, SC, PR, 3BB, 4BB, 4BB/

RE, 5BB

JINKO MODULES WITH 35 AND 40 MM FRAMES

JKMYXXXZZ-AA

WHERE “Y” CAN EITHER BE BLANK OR S; “ZZ” CAN BE M, P, OR PP; AND “AA”

CAN BE BLANK, 60, 60B, 60H, 60L, 60BL, 60HL, 60HB, 60HBL, 6HBL-EP, 60-

J4, 60B-J4, 60B-EP, 60(PLUS), 60-V, 60-MX, 72, 72-V, 72H-V, 72L-V, 72HL-V,

72-MX, 72H-BDVP, 72HL-TV, OR 72HL-V-MX3

KYOCERA MODULES WITH 46MM FRAMES

KYXXXZZ-AA

WHERE “Y” CAN BE D OR U; “ZZ” CAN BE BLANK, GX, OR SX; AND “AA” CAN

BE LPU, LFU, UPU, LPS, LPB, LFB, LFBS, LFB2, LPB2, 3AC, 3BC, 3FC, 4AC, 4BC,

4FC, 4UC, 5AC, 5BC, 5FC, 5UC, 6BC, 6FC, 8BC, 6MCA, OR 6MPA

LG MODULES WITH 35, 40, AND 46 MM FRAMES

LGXXXYAZ-BB

WHERE “Y” CAN BE A, E, N, Q, S; “A” CAN BE 1 OR 2; “Z” CAN BE C, K, T, OR

W; AND “BB” CAN BE A3, A5, B3, G3, G4, J5, K4, OR V5

VERSION: 2.0

24

REV DATE: 07/16/2020

UL2703 CERTIFIED MODULES

LONGI

MISSION SO-

LAR

MITSUBISHI

MOTECH

NEO SOLAR

POWER

PANASONIC

PEIMAR

PHILADELPHIA

SOLAR

PHONO SO-

LAR

LONGI MODULES WITH 30, 35 AND 40 MM FRAMES

LRA-YYZZ-XXXM

WHERE “A” CAN BE 4 OR 6; “YY” CAN BE BLANK, 60 OR 72; AND “ZZ” CAN BE

BLANK, BK, BP, HV, PB, PE, PH, HBD, HIB, HIH, HPB, HPH, OR HIBD

MISSION SOLAR MODULES WITH 33 AND 40 MM FRAMES

MSEBBXXXZZAA

WHERE “BB” CAN BE BLANK OR 60A; “ZZ” CAN BE BLANK, MM, SE, SO, SQ ,

SR, OR TS; AND “AA” CAN BE BLANK, 1J, 4J, 4S, 5K, 5T, 60, 6J, 6S, 6W, 8K, 8T,

OR 9S

MITSUBISHI MODULES WITH 46 MM FRAMES

PV-MYYXXXZZ

WHERE “YY” CAN BE LE OR JE; AND “ZZ” CAN BE EITHER HD, HD2, OR FB

IM AND XS SERIES MODULES WITH 40, 45, AND 50 MM FRAMES

NEO SOLAR POWER MODULES WITH 35 MM FRAMES

D6YXXXZZAA

WHERE “Y” CAN BE M OR P; “ZZ” CAN BE B3A, B4A, E3A, E4A, H3A, H4A; AND

“AA” CAN BE BLANK, (TF), ME OR ME (TF)

PANASONIC MODULES WITH 35 AND 40 MM FRAMES

VBHNXXXYYZZA

WHERE “YY” CAN BE EITHER KA, RA, SA OR ZA; “ZZ” CAN BE EITHER 01, 02,

03, 04, 06, 06B, 11, 11B, 15, 15B, 16, 16B, 17, OR 18; AND “A” CAN BE BLANK

E, G OR N

PEIMAR MODULES WITH 40 MM FRAMES

SBXXXYZZ

WHERE “B” CAN BE G, M OR P; “Y” CAN BE M OR P; AND “ZZ” CAN BE BLANK,

(BF), OR (FB)

PHILADELPHIA MODULES WITH 35 AND 40 MM FRAMES

PS-YZZAA-XXX

WHERE “Y” CAN BE M OR P; “ZZ” CAN BE 60 OR 72; AND “AA” CAN BE BLANK

OR (BF)

PHONO SOLAR MODULES WITH 35, 40, AND 45 MM FRAMES

PSXXXY-ZZ/A

WHERE “Y” CAN BE M, M1, MH, OR M1H OR P; “ZZ” CAN BE 20 OR 24; AND

“A” CAN BE F, T, U, OR TH

VERSION: 2.0

25

REV DATE: 07/16/2020

UL2703 CERTIFIED MODULES

RECOM

REC SOLAR

RENESOLA

RENOGY

RISEN

S-ENERGY

SERAPHIM EN-

ERGY GROUP

SERAPHIM

USA

SHARP

RECOM MODULES WITH 35 AND 40 MM FRAMES

RCM-XXX-6YY

WHERE “YY” CAN BE MA, OR MB, ME OR MF

REC MODULES WITH 30, 38 AND 45 MM FRAMES

RECXXXYYZZ

WHERE “YY” CAN BE AA, M, NP, PE, PE72, TP, TP2, TP2M, TP2SM, OR TP2S;

AND “ZZ” CAN BE BLANK, BLACK, BLK, BLK2, SLV, OR 72

RENESOLA MODULES WITH 35, 40 AND 50 MM FRAMES

AAXXXY-ZZ

WHERE “AA” CAN BE SPM(SLP) OR JC; “Y” CAN BE BLANK, F, M OR S; AND

“ZZ” CAN BE BLANK, AB, AB-B, ABH, ABH-B, ABV, ABV-B, BB, BB-B, BBH,

BBH-B, BBV, BBV-B, DB, DB-B, OR 24/BB

RENOGY MODULES WITH 40 AND 50 MM FRAMES

RNG-XXXY

WHERE “XXX” IS THE MODULE POWER RATING; AND “Y” CAN BE D OR P

RISEN MODULES WITH 35 AND 40 MM FRAMES

RSMYY-6-XXXZZ

WHERE “YY” CAN BE 60, 72, 120, 132 OR 144; AND “ZZ” CAN BE M OR P

S-ENERGY MODULES WITH 40 FRAMES

SNXXXY-ZZ

WHERE “Y” CAN BE M OR P; AND “ZZ” CAN BE 10, OR 15

SERAPHIM MODULES WITH 35 AND 40 MM FRAMES

SEG-AYY-XXXZZ

WHERE “A” CAN BE BLANK, 6 OR B; “YY” CAN BE BLANK, MA, MB, PA, OR PB;

AND “ZZ” CAN BE BLANK, BB, BG, BW, HV, WB, WW, BMB, BMB-HV

SERAPHIM MODULES WITH 40 AND 50 MM FRAMES

SRP-XXX-6YY-ZZ

WHERE “XXX” IS THE MODULE POWER RATING; AND “YY” CAN BE MA, MB,

PA, PB, QA-XX-XX, AND QB-XX-XX; ZZ IS BLANK, BB OR HV

SHARP MODULES WITH 35 AND 40 MM FRAMES

NUYYXXX

WHERE “YY” CAN BE SA OR SC

VERSION: 2.0

26

REV DATE: 07/16/2020

UL2703 CERTIFIED MODULES

SILFAB

SOLARIA

SOLARCITY

(TESLA)

SOLARTECH

SOLARWORLD

AG

SOLARWORLD

AMERICAS

SONALI

STION

SUNEDISON

SILFAB MODULES WITH 38 MM FRAMES

SYY-Z-XXXAB

WHERE “YY” CAN BE IL, SA, LA, SG OR LG; “Z” CAN BE BLANK, M, P, OR X; “A”

CAN BE BLANK, B, H, M, N; AND “B” CAN BE A, L, G, OR T

SOLARIA MODULES WITH 40 MM FRAMES

POWERXT XXXY-ZZ

WHERE “Y” CAN BE R OR C; AND “ZZ” CAN BE AC, BD, BX, BY, PD, PM, PM-AC,

PX, PZ, WX OR WZ

SOLARCITY MODULES WITH 40 MM FRAMES

SCXXXYY

WHERE “YY” CAN BE BLANK, B1 OR B2

SOLARTECH MODULES WITH 42 MM FRAMES

STU-XXXYY

WHERE “YY” CAN BE PERC OR HJT

SOLARWORLD SUNMODULE PLUS, PROTECT, BISUN, XL, BISUN XL, MAY BE

FOLLOWED BY MONO, POLY, DUO, BLACK, BK, OR CLEAR; MODULES WITH

31, 33 OR 46 MM FRAMES

SW-XXX

SOLARWORLD SUNMODULE PLUS, PROTECT, BISUN, XL, BISUN XL, MAY BE

FOLLOWED BY MONO, POLY, DUO, BLACK, BK, OR CLEAR; MODULES WITH

33 MM FRAMES

SWA-XXX

SONALI MODULES WITH 40 MM FRAMES

SSXXX

STION THIN FILM MODULES WITH 35 MM FRAMES

STO-XXX OR STO-XXXA

SUNEDISON MODULES WITH 35, 40 & 50 MM FRAMES

SE-YXXXZABCDE

WHERE “Y” CAN BE B, F, H, P, R, OR Z; “Z” CAN BE 0 OR 4; “A” CAN BE

B,C,D,E,H,I,J,K,L,M, OR N ; “B” CAN BE B OR W; “C” CAN BE A OR C; “D” CAN

BE 3, 7, 8, OR 9; AND “E” CAN BE 0, 1 OR 2

VERSION: 2.0

27

REV DATE: 07/16/2020

UL2703 CERTIFIED MODULES

SUNIVA

SUNPOWER

SUNSPARK

SUNTECH

TALESUN

TRINA

URE

SUNIVA MODULES WITH 35, 38, 40, 46, AND 50 MM FRAMES

OPTXXX-AA-B-YYY-Z

MVXXXX-AA-B-YYY-Z

WHERE “AA” IS EITHER 60 OR 72; “B” IS EITHER 4 OR 5; “YYY” IS EITHER

100,101,700,1B0, OR 1B1; AND “Z” IS BLANK OR B

SUNPOWER STANDARD (G3 OR G4) OR INVISIMOUNT (G5) 40 AND 46 MM

FRAMES

SPR-ZB-XXX-YY

WHERE “Z” IS EITHER A, E, P OR X; “B” CAN BE BLANK, 17, 18, 19, 20, 21, OR

22; AND “YY” CAN BE BLANK, BLK, COM, C-AC, D-AC, E-AC, G-AC, BLK-C-AC,

OR BLK-D-AC

SUNSPARK MODULES WITH 40 MM FRAMES

SYY-XXXZ

WHERE “YY” CAN BE MX OR ST; AND “Z” CAN BE M, P OR W

SUNTECH MODULES WITH 35, 40 AND 50MM FRAMES

STPXXXY-ZZ/AA

WHERE “Y” IS BLANK OR S; AND “ZZ” CAN BE 20, 24; AND “AA” CAN BE VD,

VEM, VFW, WDB, WDE OR WD

TALESUN MODULES WITH 35 AND 40 FRAMES

TP6YZZAAXXX-B

WHERE “YY” CAN BE BLANK, F OR H; “ZZ” CAN BE 60 OR 72; “AA” CAN BE M

OR P; AND “B” CAN BE BLANK, B, T, OR (H)

TRINA MODULES WITH 30, 35, 40 AND 46MM FRAMES

TSM-XXXYYZZ

WHERE “YY” CAN BE DD05, DD06, DD14, DE14, DE15, DEG15, PA05, PC05,

PD05, PD06, PA14, PC14, PD14, PE14, OR PE15 ; AND “ZZ” CAN BE BLANK,

.05, .08, .10, .18, .08D, .18D, 0.82, .002, .00S, 05S, 08S, A, A.05, A.08, A.10,

A.18, A(II), A.05(II), A.08(II), A.082(II), A.10(II), A.18(II), H, H(II), H.05(II), H.08(II),

HC.20(II), HC.20(II), M, M(II), M.05(II), MC.20(II)

URE MODULES WITH 35 MM FRAMES

DYZXXXHAA

WHERE “Y” CAN BE 6 OR 7; “Z” CAN BE K OR M; AND “AA” CAN BE H3A, H4A,

OR H8A

VERSION: 2.0

28

REV DATE: 07/16/2020

UL2703 CERTIFIED MODULES

VIKRAM

VSUN

WINAICO

YINGLI

ZNSHINE

VIKRAM SOLAR MODULES WITH 40 MM FRAMES

VSYY.ZZ.AAA.BB

WHERE “YY” CAN BE M, P, MBB, MH, MS, MHBB, OR PBB; “ZZ” CAN BE 60 OR

72; “AAA” IS THE MODULE POWER RATING; AND “BB” CAN BE 03.04 OR 05

VSUN MODULES WITH 35 AND 40 MM FRAMES

VSUNXXX-YYZ-AA

WHERE “YY” CAN BE 60, 72, 120, OR 144; “Z” CAN BE M, P, MH, PH, OR BMH;

AND “AA” CAN BE BLANK, BB, OR DG

WINAICO MODULES WITH 35 AND 40 MM FRAMES

WSY-XXXZA

WHERE “Y” CAN BE EITHER P OR T; “Z” CAN BE EITHER M, P, OR MX; AND “A”

CAN BE BLANK OR 6

PANDA, YGE, YGE-U, AND YLM SERIES MODULES WITH 35, 40, AND 50 MM

FRAMES

ZNSHINE MODULES WITH 30, 35, AND 40MM FRAMES

ZXY6-ZZAA-XXX/B

WHERE “Y” CAN BE M OR P; “ZZ” CAN BE BLANK, H, HLD, HLDD, LD, LDD,

NH, NHLD OR NHLDD; “AA” CAN BE 60, 72, 120 OR 144; AND “B” CAN BE M

OR P

VERSION: 2.0

29

REV DATE: 07/16/2020

CLAMP TABLES

Frame Thickness

30 mm

32 mm

35 mm

38 mm

40 mm

45 mm

50 mm

End Clamps

Article Number

1510015

1510016

1510017

1510018

1510019

1510020

1510021

Frame Thickness

30-40 mm

40-50 mm

Mid Clamps

Article Number

1510011

1510012

INSTALLER RESPONSIBILITIES

Periodic reinspection of components shall be performed to verify that there is no corrosion detrimental to system strength and electrical conductivity, no loose bolts, and/or other variables that could compromise array safety. Any corroded or damaged components shall be immediately replaced.

VERSION: 2.0

30

REV DATE: 07/16/2020