T2000 Explosion Proof I/P & E/P Transducers

T2000 Explosion Proof I/P & E/P Transducers
T2000 Explosion Proof
I/P & E/P Transducers
•
•
•
Field-selectable inputs and direct/reverse/split ranging
Multiple input/output/mounting configurations
Precise, reliable performance under extreme conditions of
temperature, vibration, orientation, supply pressure changes,
supply voltage changes, RFI/EMI, humid/oil-laden media,
and corrosive surroundings
The T2000EX is a robust electronic instrument that regulates
an incoming supply pressure down to a precise output pressure
which is directly proportional to an electrical control signal. The
secret to the T2000EX’s precise, reliable performance under a variety of demanding environmental conditions is a patented piezoceramic actuator with many industry-wide firsts.
Applications
•
•
•
•
Valve Actuators •
Valve Positioners •
Relay
•
Controllers
Chemical & Petrochemical Industries
Petroleum Production
Pipeline Transmission
Principle of Operation
The T2000EX I/P and E/P transducers utilize closed-loop pressure feedback-control for precision pressure output and minimized effects of temperature, supply pressure changes, supply
voltage changes, and mounting angle.
Supply pressure is reduced by the supply valve to provide an output pressure which is internally routed to a precision temperature
compensated piezo resistive pressure sensor. Supply pressure is
also routed to an externally removable orifice which provides a reduced pilot pressure to a chamber containing a servo diaphragm
and nozzle. Pilot pressure is controlled by modulating the gap
between the face of a nozzle and an adjacent piezo-ceramic actuator, which is part of a unique patented mechanism.
The piezo-ceramic actuator serves as a control link between electrical input and pressure output as follows:
•
•
•
•
•
The input current (I/P) or voltage (E/P) signal is conditioned
to provide a normalized control signal directly proportional
to the desired pressure output.
Simultaneously the output of the pressure sensor is amplified and conditioned to produce a feedback signal.
The sum of the control signal and the feedback signal produce a command signal which is delivered as a DC voltage
to the piezo-ceramic actuator.
As voltage increases, the force applied by the actuator
increases, so as to restrict nozzle bleed and thus increase
pilot pressure.
Increased pilot pressure applied to the servo diaphragm
directly causes opening of the supply valve and an increase
in the output pressure until the output feedback signal and
control signal combine to produce the correct command
signal.
Air Quality
Instrument-quality air consists of
a. A dew point less than 35˚F
b. No particles larger than three microns
c. Maximum oil content of 1 ppm
belgas.net
Fine-Tuning Your Application
For optimal performance in your application, the calibration of the
Type 2000EX can be fine-tuned in the field. An easily-removable
cover provides access to the isolated electronics. All potentiometers, connections, jumpers, and switches are clearly marked on
the circuit board or on the handy chart located on the inside
of the cover. The three elements of calibration (Gain, Zero, and
Span) are described below. Consult the T2000EX User’s Manual
for detailed calibration procedures, cautions, and instrumentation
requirements.
Gain (Damping) Adjustment
The output response of the T2000EX can be optimized for varying downstream volumes by adjusting the system gain of the control circuit. Adjust the Gain Pot counterclockwise for increased
gain; clockwise for increased oscillation damping. For maximum
allowable gain in your application, the pot should be turned clockwise until oscillation just disappears.
Zero & Span Adjustments
The T2000EX contains multi-turn Coarse-Zero, Fine-Zero, and
Span adjustment potentiometers which are clockwise positive.
Adjustment of either Zero Pot changes the unit’s minimum output
while the Span Pot changes the maximum output. The adjustments are interactive, so it may take iterations to reach the desired calibration.
Wide Rangeability
The T2000EX can be field calibrated to pressure ranges other
than the standard ones by combinations of recalibration, pressure
range switching, and split high/low ranging. A unit should not be
switched to a range outside its pressure sensor family (eg., 0-15
PSIG can be switched to a 3-15 PSIG, but not to 0-30 PSIG). (Caution: Do not exceed the range of the onboard pressure sensor.)
For example, the easiest way to recalibrate a 0-30 PSIG unit to
3-15 PSIG would be to change the switch setting to 3-27 PSIG,
then switch to split range low.
Field-Selectable Features
Onboard switches allow the user to easily reconfigure the
T2000EX for any of several electrical inputs, direct/reverse acting, or output split-ranging high/low. Fine tuning of the unit’s
calibration may be necessary after a reconfiguration.
< 109 >
T2000 Part Matrix
Direct/Reverse Acting
Direct Acting transducers regulate to their minimum output when supplied with minimum input;
maximum out with maximum in. Reverse Acting
transducers regulate to their maximum output at
minimum input.
2K E
1
00
Electrical Port
1⁄2 NPT Conduit
Pneumatic Ports
NPT
BSPT
BSPP
Manifold Mount*
Agency Approval
FM/CSA
FM Natural Gas
Approval for US and
Canada, includes factory
conduit seal
Electrical Input
4-20 mA
N
Split Ranging–High & Low
N
T
P
M
The T2000EX can be configured to regulate either
half (top or bottom) of it’s normal output range,
when supplied with it’s normal full-ranging electrical input. For example, a 0-10V 0-30 PSIG unit set
to split range low will regulate 0-15 PSIG @ 0-10V.
It will regulate 15-30 PSIG @ 0-10V if set to split
range high.
F
G
Hazardous Area &
Usage Classification
42
05
15
19
11
01
“F” model: Dual Listing of FM/CSA for following approvals:
Explosion Proof: Class I, Division 1, Groups A,B,C,D, T6 @ 60°C Max
Dust Ignition Proof: Class II, III, Division 1, Groups E,F,G; T6 @
60°C Max
Intrinsic Safety: FM/CSA Class I II III, Division 1, Groups
A,B,C,D,E,F,G, T4 @ 60°C Max
Non-incendive: Class I, Division 2, Groups A, B, C, D. T4 @ 60°C Max
0-10 V
Environmental rating: TYPE 4X, IP66
F
H
L
Note: Certified by FM, “F” model can be used in Natural Gas application in US and Canada, merely in a condition that a suitably rated NRTL listed or certified conduit seal is mandatory.
1
“G” model: Listing of FM for using Natural Gas as a process medium
in US and Canada for following approvals:
005
015
315
117
030
630
327
060
100
120
Explosion Proof: Class I, Division 1, Groups A,B,C,D, T6 @ 60°C Max
Dust Ignition Proof: Class II, III, Division 1, Groups E,F,G; T6 @
60°C Max
Intrinsic Safety: FM Class I II III, Division 1, Groups A,B,C,D,E,F,G
T4 @ 60°C Max
Non-incendive: Class I, Division 2, Groups A, B, C, D. T4 @ 60°C Max
Suitable for use in Class II III, Division 2, Groups F, G. T4 @ 60°C Max
Environmental rating: TYPE 4X, IP66
Note: “G” model includes a factory conduit seal. No additional NRTL
certified seal is required for Natural Gas application.
CE: (Conduit Connector Only) EN 50081-1 Residential, commercial &
light industry; EN-50082-2 Heavy Industrial.
It is mandatory for the user to install a suitably
rated NRTL Listed or Certified conduit seal.
Bottom O-Ring Ports
0-5 V
1-5 V
1-9 V
1-10 V
D
R
Suitable for use in Class II III, Division 2, Groups F, G. T4 @ 60°C Max
*
Direct Acting
Reverse Acting
Pneumatic Output
Full Range
Split Range High
Split Range Low
Pressure Ranges
PSIG
BAR
0-5
0-0.3
0-15
0-1.0
3-15
0.2-1.0
1-17
0.07-1.2
0-30
0-2.1
6-30
0.4-2.1
3-27
0.2-1.9
0-60
0-4.1
0-100
0-6.9
0-120
0-8.3
Specials
00 None
Maximum supply for
these pressure ranges
is 100 psig.
Maximum supply for
these pressure ranges
is 140 psig.
Terminal Block
I/P Transducer
E/P Transducer
S
+
-
N/C
+ Signal
- Signal
+ Signal
+ Power Supply
Common
Type 2000 Wiring Connections and Switch Positions
Switch #
ON
Switch #
OFF
< 110 >
1: psig
0-15
3-15
1-17
0-30
3-27
6-30
0-100
1: psig
BAR
0-1.0
0.2-1.0
0.07-1.2
0-2.1
0.2-1.9
0.4-2.1
0-6.9
BAR
0-60
0-120
0-4.1
0-8.3
2
1-5 VDC
0-5 VDC
2
1-9 VDC
0-10 VDC
4-20 mA
3
4
5
6: psig
BAR
7
8
9
Split Low
Voltage
Input
(E/P)
Split Low
Full
0-15
1-17
0-30
0-60
0-100
0-120
0-1.0
0.07-1.2
0-2.1
0-4.1
0-6.9
0-8.3
Reverse
Acting
Full
I/P
3
4
5
8
9
Current
Input (I/P)
Split High
BAR
0.2-1.0
0.2-1.9
0.4-2.1
7
Full
Split High
6: psig
3-15
3-27
6-30
Direct
Acting
Split Low
Split High
E/P
belgas.net
Accessories
Mounting Options
Mounting Method
In-Line
Direct Mounting
Panel Bracket
Valve Bracket
Pipe Bracket
DIN-Rail Bracket
Manifold Plate
Explosion-Proof (E) Model
Yes
Side or Bottom Holes
Accessory
Supplied
Accessory
Accessory
Accessory
Mounting: The Type 2000 can be mounted in-line, or directly to a panel via mounting holes
located in the side and bottom of the unit. In addition, the S model includes a panel-mounting
bracket; while the E model includes a valve-mounting bracket. Kits are available for mounting of either model to panel, valve, pipe, or DIN-Rail. A custom plate is available for mounting of the bottom-ported version to a manifold. (See Accessories)
Panel Mounting Kit
Valve Mounting Kit
2" Pipe Mounting Kit (Valve Mounting Kit is required)
DIN Rail Adapter
Manifold Adapter Kit
Filter Kit, 60 microns
Pressure Gauge Kit 15 psig (1 BAR)
Pressure Gauge Kit 30 psig (2.1 BAR)
Pressure Gauge Kit 60 psig (4.1 BAR)
Pressure Gauge Kit 160 psig (11 BAR)
Part Number
010-135-000
010-134-000
010-143-000
010-115-000
971-158-000
010-139-000
010-138-000
010-138-001
010-138-002
010-138-003
T2000 Specifications
Accuracy
Electrical
0.1% of full-scale output typical (0.25% guaranteed);
includes effects of hysteresis, dead band, and repeatability
Switch-Selectable
4-20mA. 0-5, 1-5, 1-9, 1-10, or 0-10VDC
Connections
1/2 NPT or 20mm Conduit
Power Supply
5-28VDC (with voltage inputs only)
Direct/Reverse Acting Switch-Selectable
Pneumatic
0-5, 0-15, 3-15, 1-17, 0-30, 6-30, 3-27, 0-60,
PSIG
0-100, or 120
Outputs
0-0.1, 0-0.3, 0-1.0, 0.2-1.0, 0.07-1.2, 0-2.1,
BAR
0.4-2.1, 0.2-1.9, 0-4.1, 0-6.9, 0-8.3
1/4 (NPT, BSPT, or BSPP threads)
Ports (Input/Output)
Bottom-ported for Manifold Mounting
Exhaust
(Explosion proof only) 1/8 - 27 NPT
Ports (Gauge)
1/8 NPT
For 0–5 PSIG (0.3 BAR) Through 0–60 PSIG
From 5 PSIG (0.3 BAR) above maximum output to 100
PSIG maximum
Supply
For 0-100 PSIG and 0–120 PSIG Ranges
From 5 PSIG (0.3 BAR) above maximum output to 140
PSIG maximum
Switch-Selectable, Full-Range or Split-Range High or
Split-Ranging
Split-Range Low
Consumption
4 scfh maximum (1.9 LPM)
Range
Sensor
Flow
PSIG
BAR
PSIG BAR scfm
LPM
0-5
0-0.3
5
0.3
11
312
0-15
0-1.0
15
1.0
15
423
3-15
0.2-1.0
15
1.0
15
423
1-17
0.07-1.2
15
1.0
15
423
0-30
0-2.1
30
2.1
15
423
Flow Capacity
3-27
0.2-1.9
30
2.1
15
423
6-30
0.4-2.1
30
2.1
15
423
0-60
0-4.1
50
3.5
15
423
(Typical Flow @ 100 PSIG (6.9 BAR) in and maximum out)
0-100
0-6.9
100
6.9
21
595
0-120
0-8.3
100
6.9
21
595
(Typical Flow @ 140 PSIG (9.7 BAR) in and maximum out)
3 SCFM (85 LPM) @ 5 PSIG (0.3 BAR) above setpoint
Exhaust Capacity
(0-15 PSIG range unit set at mid range)
Stability
Supply Voltage Effect None
Supply Pressure
None
Effect
Vibration Effect
<1% FS (+/-1G; 5-1000Hz)
Mounting Position
None
Effect
RFI/EMI
CE-Compliant
Temperature Effect
0.02% FS/˚F (-40˚ to 180˚F [-40˚ to 82˚C])
Storage Temperature -40˚to 200˚F (-40 to 93˚C)
Approximate Weight 3.0 lbs, 1.35 kg
Inputs
Sealing Fittings for FM approved
T2000 EX Transducers
Application & Installation
Class I, Divisions 1 & 2
Seals in a Class I hazardous location is to minimize the passage
of gases and vapors and prevent the passage of flames from
one electrical installation to another through the conduit system.
Seals are required to be installed within 18 inches on any conduit run entering an enclosure which contains devices that may
produce arcs, sparks or high temperatures.
The T2000 Explosion Proof Transducer is available with the seal
fitted to the transducer conduit port or can be supplied as a component to be applied at the installation of the system.
It is mandatory for a suitably rated conduit
seal to be installed with the FM approved
T2000 EXP Transducer.
Vertical or Horizontal Seals
All seal housings are approx. 3-1/2" in laying length and 1-1/2" OD
Part Number
SF-04AMM
SF-04AMF
SF-04IMM
SF-04IMF
Description
1/2" Aluminum
1/2" Aluminum w/nipple
1/2" Iron
1/2" Iron w/nipple
Sealing Materials
Per seal housing installed, approx. 1/16 oz of packing fiber is used
for the dam and 1.5 oz of compound is used for the seal.
Part Number
SC-4
SC-8
FP-4
Description
4 oz. Sealing Compound
8 oz. Sealing Compound
4 oz. Packing Fiber
Larger quantities of fiber and compound available upon request.
belgas.net
< 111 >
Type 2000 Explosion Proof Dimensions
Agency Approvals - Applies only to units ordered with approvals
Factory Mutual
T-2000 I/P & E/P Transducers Explosion Proof / Intrinsically Safe Model
Explosion Proof: Class I, Division 1, Groups A, B, C, & D, T6 Ta = 60°C
Dust-Ignition Proof: Classes II & III, Division 1, Groups E, F, & G , T6 Ta = 60°C; Type 4X
NEMA 4X, IP66
Intrinsically Safe: Classes I, II, & III, Division 1, Groups A, B, C, D, E, F, & G , T4 Ta =
60°C; Entity; Type 4X NEMA 4X, IP66
Non-incendive: Class I, Division 2, Groups A, B, C, & D, T4 Ta = 60°C
Suitable: Class II, Division 2, Groups F & G , T4 Ta = 60°C
Suitable: Class III, Division 2, T4 Ta = 60°C, Type 4X, IP66
Entity Parameters:
Input Option b = 42: VMax = 30 V, IMax = 200 mA, PMax = 1 W, Ci = 0, Li = 0.
Input Option b = 01, 05, 11, 15 or 19: VMax = 30 V, IMax = 100 mA, PMax = 0.75 W, Ci = 0, Li = 0.
Special Conditions of Use:
The T-2000 for use with natural gas as a process medium, where a NRTL listed or certified conduit
seal or a factory conduit seal is used.
T-2000 E/P or I/P Transducers Intrinsically Safe Model
Intrinsically Safe: Classes I, II, & III, Division 1, Groups A, B, C, D, E, F, & G, T4 Ta =
60°C; Entity;
Non-Incendive: Class I, Division 2, Groups A, B, C, & D, T4 Ta = 60°C
Suitable: Class II, Division 2, Groups F & G, T4 Ta = 60°C
Suitable: Class III, Division 2, T4 Ta = 60°C Type 4X NEMA 4X
Entity Parameters:
When Electrical Input Option c = 42: VMax = 30 V, IMax = 200 mA, PMax = 1 W, Ci = 0, Li = 0.
When Electrical Input Option c = 05, 15, 19, 11 or 01: VMax = 30 V, IMax = 100 mA, PMax = 0.75
W, Ci = 0, Li = 0.
T-2000 E/P or I/P Transducers Intrinsically Safe with Terminal Block Model
Intrinsically Safe: Class I, Division 1, Groups A, B, C, & D, T4 Ta = 60°C Entity;
Non-Incendive: Class I, Division 2, Groups A, B, C, & D, T4 Ta = 60°C
Entity Parameters:
When Electrical Input Option c = 42: VMax = 30 V, IMax = 200 mA, PMax = 1 W, Ci = 0, Li = 0.
When Electrical Input Option c = 05, 15, 19, 11 or 01: VMax = 30 V, IMax = 100 mA, PMax = 0.75
W, Ci = 0, Li = 0.
Drawings and
dimensions are for
reference only.
REGULATED PRESSURE VS . FLOW
PSIG BAR
70 4.8
140 psig supply pressure
Canadian Standards Association - T-2000 I/P & E/P Transducers
Hazardous Locations: Class I, Division 1, Groups A, B, C, & D; Class II, Groups E, F &
G; Class III.
Explosion Proof I/P & E/P Transducer, Rated: 28Vdc, 8mA;
T-Code T6; Enclosure Type 4X NEMA 4X, IP66;
Max Ambient Temperature: +60°C. IN COMPLIANCE WITH STD C22.2 No 213.
T-2000 I/P & E/P Transducers
Intrinsically Safe, Entity - Hazardous Locations: Class I,
Divisions 1 & 2, Groups A , B, C, & D; Class II, Division 1, Groups E, F, & G,
Division 2, Groups F & G; Class III Hazardous Locations
Electro-Pneumatic I/P and E/P Transducers. Maximum Ambient Temperature:
+60°C. Enclosure Type 4X NEMA 4X, T4. Intrinsically Safe when installed.
Explosion proof: Class I, Division 1, Groups A, B, C & D; Class II, Groups
E, F, & G; Class III. NEMA 4X
Rated: 28Vdc, 8mA; T-Code T6; Enclosure Type 4X, IP66; Max Ambient
Temperature: +60°C. Intrinsically Safe when installed. Two sets of Entity
Parameters may be used in the installation of this product.
Entity Parameters
I/P: VMax = 30V Imax = 200mA PMax = 1.0W Ci = 0mF Li = 0mH
E/P: VMax = 30V IMax = 100mA PMax = 0.75W Ci = 0mF Li = 0mH
ATEX (EUROPEAN MODEL)
T-2000 I/P & E/P Transducers
INTRINSIC SAFETY: II 1 G EEx ia IIC T4 (-20<Ta<+60) EN 50014:1997 (A2) EN
50020:1994 EN 500284:1999
Regulated Pressure
60 4.1
50 3.4
40 2.8
30 2.1
It is mandatory for the user to install a
suitably rated NRTL Listed or Certified conduit seal
20 1.4
10 0.7
0 0
SCFM 0
LPM 0
< 112 >
2
57
4 6 8 10 12 14 16 18 20 22 24
113 170 227 283 340 397 453 510 566 623 680
Forward Flow
The Bellofram T-2000 Transducers were tested and found to comply with Electromagnetic
Compatibility Directive effective January 1, 1996. The relevant EMC specifications tested were
the following: EN 50081-1 (1992) and EN 50082-1 (1992). A Technical Construction File, Serial
#107 was written and Certificate of Conformity issued by a Competent Body.
belgas.net
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement