User`s Manual for Biometric/Key Pad Safe

Add to my manuals
2 Pages

advertisement

User`s Manual for Biometric/Key Pad Safe | Manualzz

User’s Manual for

Biometric/Key Pad Safe

Read all instructions before using this safe.

WARNING

- Safe can be opened by either Fingerprint, PIN code,

and/or Emergency Keys.

- If user resets the safe to Factory Default mode: ANY

fingerprint and Factory Default PIN code can open

the safe.

- Register both Fingerprint and PIN code to disable

Factory Default mode.

- Register at least two different fingerprints and test a few

times before closing the safe door.

- Test with a non-registered fingerprint. If the safe opens,

the safe is still in Factory Default mode.

- Avoid leaving safe door open and unattended; it will allow

unauthorized individuals to add their fingerprints and/or

reprogram the safe, gaining full access to the safe and

the contents.

- Test the Emergency Keys and store them in a secure

place, NOT inside of the safe.

- To maximize the security and performance of the safe,

test registered fingerprints every 6 months.

I

A B

H

* Actual model may vary

A. Initialization Button

B. Battery Compartment

C. Bolts

D. Fingerprint Scanner

E. Indicator Lights

U n loc k

Lo c k

C

E

G

F. Enter Button

G. Key Pad

H. Knob

I. Logo Plate and

Emergency Key Access

D

F

GETTING STARTED

1. Remove Emergency Keys from accessory package

- To expose the Emergency Key Access, remove Logo Plate

(I) screws with provided tool

- Insert Emergency Key into key access, push and turn

counter-clockwise

- Turn the Knob (H) clockwise to open

Note: Store Emergency Keys in a secure place, NOT inside of

the safe

2. Continue with INSTALL BATTERIES

INSTALL BATTERIES

1. With safe door open, remove Battery Compartment (B) cover

- Insert 4 AA batteries and restore battery cover

- Continue with FINGERPRINT REGISTRATION

FINGERPRINT REGISTRATION

IMPORTANT: The safe is in either Factory Default mode or

Pre-registered mode, test safe to determine factory settings below

Factory Default mode: Safe can be opened with ANY fingerprint(s)

Pre-registered mode: Safe can NOT open with any fingerprint(s)

During registration the door must remain open and Bolts (C) must be in the retracted position. Otherwise, the fingerprint will not be saved

To retract bolts:

- Insert Emergency Key into key access, push and turn

counter-clockwise

- Turn the Knob (H) clockwise to retract bolts

1. Press and release Initialization Button (A)

2. Immediately place a finger on the Fingerprint Scanner (D)

- Hold finger still

- Two beeps will be heard recognizing the fingerprint; followed

by one long beep

- Remove finger

- Registration is complete

Successful Registration

Registration is successful when two short beeps are heard, followed by one long beep

Unsuccessful Registration

Registration failed if two short beeps are heard, followed by three short beeps

3. To register another fingerprint, repeat steps 1 - 2

4. Continue with TEST A (NON) REGISTERED FINGERPRINT

Fingerprint Memory Full

If the Indicator Lights (E) flash and beep twice followed by a few green flashes, it indicates the memory is full. Refer to DELETE

STORED FINGERPRINTS AND PIN CODE / RESET TO

FACTORY DEFAULT MODE for more options

TEST A (NON) REGISTERED FINGERPRINT

1. Test multiple Non-Registered fingerprints

- Close safe door and lock by turning the Knob (H) counter-

clockwise

- To begin the testing process, press and release Enter

Button (F)

- Place a non-registered finger on the Fingerprint Scanner (D)

- Door should NOT open; three short beeps will be heard

- If the door opens with a non-registered fingerprint,

registration was unsuccessful; the safe remains in Factory

Default mode

IMPORTANT: If registration was unsuccessful repeat steps under FINGERPRINT REGISTRATION, and test non-registered fingerprint

2. Test Registered fingerprint

- Close safe door and lock by turning the Knob (H) counter-

clockwise

- To begin the testing process, press and release Enter

Button (F)

- Place a registered finger on the Fingerprint Scanner (D)

- Door should OPEN, one long beep will be heard, turn the

Knob (H) clockwise to open the safe

- Fingerprint registration was successful

3. Continue with PIN CODE REGISTRATION

PIN CODE REGISTRATION

IMPORTANT: Safe only retains one PIN code; Factory Default

PIN code is 1234

1. Press and HOLD number “1” key until the green Indicator

Light (E) turns on, release button

- Enter Factory Default PIN code 1234, press Enter Button

(F), one long beep will be heard

- Enter new PIN code (four to eight digits), press Enter Button

(F), two short beeps will be heard

- Re-enter new PIN code, press Enter Button (F), one long

beep will be heard

- Registration is complete

2. If you hear three short beeps with red/green Indicator Lights

(E) flashing, it indicates the new PIN code registration was

unsuccessful, repeat step 1

3. Continue with TEST A (NON) REGISTERED PIN CODE

See reverse side for more information

10/12

BC256

TEST A (NON) REGISTERED PIN CODE

1. Test Factory Default PIN code 1234

- Close safe door and lock by turning the Knob (H) counter-

clockwise

- To begin the testing process, enter PIN code 1234, press

and release Enter Button (F)

- Door should NOT open; three short beeps will be heard

indicating PIN entry was incorrect

- If Factory Default PIN code 1234 opens the safe door, PIN

code registration was unsuccessful; and safe remains in

Factory Default PIN code mode

IMPORTANT: If registration was unsuccessful repeat steps under PIN CODE REGISTRATION, and test Factory Default

PIN code

2. Test Registered PIN code

- Close safe door and lock by turning the Knob (H) counter-

clockwise

- To begin the testing process, enter new registered PIN code,

press and release Enter Button (F)

- Door should OPEN, one long beep will be heard indicating

PIN entry was correct, turn the Knob (H) clockwise to open

the safe

- PIN code registration was successful

CHANGE PIN CODE

1. Press and HOLD number “1” key until the green Indicator

Light (E) turns on, release button

- Enter current PIN code, press Enter Button (F), one long

beep will be heard

- Enter new PIN code (four to eight digits), press Enter Button

(F), two short beeps will be heard

- Re-enter new PIN code, press Enter Button (F), one long

beep will be heard

- PIN code has been changed

2. If you hear three short beeps with red/green Indicator Lights

(E) flashing, it indicates the new PIN code registration was

unsuccessful, repeat steps under CHANGE PIN CODE

3. Continue with TEST A (NON) REGISTERED PIN CODE

CLOSE/OPEN SAFE DOOR

CLOSE: Close the safe door and turn the Knob (H) counterclockwise to lock the safe

OPEN WITH FINGERPRINT:

- Press and release Enter Button (F)

- Place a registered finger on the Fingerprint Scanner (D)

- One long beep will be heard and the green Indicator Light

(E) turns on

- Turn the Knob (H) clockwise to open the safe

OPEN WITH PIN CODE:

- Enter PIN code, press Enter Button (F)

- One long beep will be heard and the green Indicator Light

(E) turns on

- Turn the Knob (H) clockwise to open the safe

DOOR OPEN ALARM

The door alarm is activated ONLY when the safe door is left open and the Bolts (C) are retracted

1. Within 1 minute, the green Indicator Light (E) will start

flashing, followed by one beep

- It will beep every 3-5 seconds

- Close the safe door, and turn the Knob (H) counter-

clockwise to cease the alarm

2. With the safe door open and the Bolts (C) extended, no

Indicator Lights (E) or beeps will be heard

LOW BATTERY WARNING

1. When the door is closed and the Indicator Light (E) displays

red, this indicates batteries are low. Replace batteries

immediately

2. Use Emergency Key to open safe

- To expose the Emergency Key Access, remove Logo Plate

(I) screws with tool provided

- Insert Emergency Key into key access, push and turn

counter-clockwise

- Turn the Knob (H) clockwise to open

3. Replace batteries

- Remove Battery Compartment (B) cover and all

4 AA batteries

- Insert 4 new AA batteries and restore Battery

Compartment (B) cover

Note: All registered fingerprints and PIN code remain stored

DELETE STORED FINGERPRINTS AND PIN CODE /

RESET TO FACTORY DEFAULT MODE

1. Open the safe door

- Press and HOLD the Initialization Button (A)

- The green Indicator Light (E) will flash approximately fifteen

times, followed by one long beep

- RELEASE Initialization Button (A)

2. If the green Indicator Light (E) did not flash and one long

beep was not heard, repeat step 1

3. All fingerprints and the PIN code stored in the safe have

been deleted

Note: The safe is in Factory Default mode. ANY fingerprint and

Factory Default PIN code 1234 can open the safe

CARE AND MAINTENANCE

- To maximize the security and performance of the safe, keep

Fingerprint Scanner (D) clean; use a dry cloth to remove any

smudges or prints off the Fingerprint Scanner after each use

- Test registered fingerprints and PIN code every 6 months

- Keep liquids away from the control panel. Spills on the control

panel will cause damage and possibly electric shock

- Secure safe in a proper area to prevent from falling and

causing damage or injury

- DO NOT disassemble the product. For all repairs, contact

BARSKA Customer Service

- DO NOT use chemicals or cleaning agents to clean the safe

MOUNTING INSTRUCTIONS

The safe may be mounted to a wall or floor. Be aware of the load bearing. Failure to do so can result in personal injury and/or damage to property. Use

Mounting Holes appropriate tools when performing work and always use eye protection

Wall Mounting

Do not mount the safe without anchoring to the wall

- Find the studs in the wall, at

your desired location. Most

studs are 16 inches or 24

inches apart

* Actual model may vary

- Check the wall for concealed wires or pipes

- Measure the location of the pre-set drill holes; mark their exact

position onto the wall ensuring that the studs or anything else

behind will not interfere

- Drill the appropriate size holes for the anchors you are using

- Carefully press the anchor into the holes at this time

- Mount the safe by running screws from inside of the safe and

securing to anchors; ensure the safe is mounted securely

Floor Mounting

- Use proper drill tools depending on the type of floor you are

mounting the safe (wood, tile, or concrete)

- Measure the location of the pre-set drill holes; mark their exact

position onto the floor

- Drill the appropriate size holes for the anchors you are using

- Carefully press the anchor into the holes at this time

- Mount the safe by running screws from inside of the safe and

securing to anchors; ensure the safe is mounted securely

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement