Allen-Bradley PV 300, PV 550, PV 600, PV 900, PV 1000, PV 1400 PanelView Terminal User Manual
Below you will find brief information for PanelView Terminal PV300, PanelView Terminal PV550, PanelView Terminal PV600, PanelView Terminal PV900, PanelView Terminal PV1000. The PanelView terminals provide operator interface functionality for industrial applications. These terminals can be used to control and monitor various processes, such as machine control, data acquisition, and system status monitoring. With their intuitive interfaces, the PanelView terminals allow operators to interact with the control system easily and efficiently.
Advertisement
Advertisement
PanelView
Standard Operator
Terminals
PV300, PV550, PV600, PV900,
PV1000, PV1400
User Manual
Important User Information
Because of the variety of uses for the products described in this publication, those responsible for the application and use of this control equipment must satisfy themselves that all necessary steps have been taken to assure that each application and use meets all performance and safety requirements, including any applicable laws, regulations, codes and standards.
The illustrations, charts, sample programs and layout examples shown in this guide are intended solely for purposes of example.
Since there are many variables and requirements associated with any particular installation, Allen-Bradley does not assume responsibility or liability (to include intellectual property liability) for actual use based upon the examples shown in this publication.
Allen-Bradley publication SGI-1.1, Safety Guidelines for the
Application, Installation and Maintenance of Solid-State Control
(available from your local Allen-Bradley office), describes some important differences between solid-state equipment and electromechanical devices that should be taken into consideration when applying products such as those described in this publication.
Reproduction of the contents of this copyrighted publication, in whole or part, without written permission of Rockwell Automation, is prohibited.
Throughout this manual we use notes to make you aware of safety considerations:
!
ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property damage or economic loss.
Attention statements help you to:
• identify a hazard
• avoid a hazard
• recognize the consequences
Important: Identifies information that is critical for successful application and understanding of the product.
PanelBuilder32, PanelView, SLC, SLC 500, SLC 5/01, SLC 5/02, SLC 5/03, SLC 5/0, MicroLogix,
ControlLogix, Data Highway Plus are trademarks of Allen-Bradley Company, Inc.
PLC and PLC-5 are registered trademarks of Allen-Bradley, Inc.
Microsoft, MS-DOS and Windows are trademarks or registered trademarks of Microsoft Corporation.
x-4
Preface
Terminal Overview
Initial Setup
Contents of Manual . . . . . . . . . . . . . . . . . . . . . . . P-2
Intended Audience . . . . . . . . . . . . . . . . . . . . . . . P-3
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . P-3
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . P-3
Installing PanelView Terminals . . . . . . . . . . . . . P-3
European Union Directive Compliance . . . . . . . P-3
Related Publications . . . . . . . . . . . . . . . . . . . . . . P-4
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . P-4
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . 1-1
Intended Uses . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Terminal Types . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
PanelView 300 Features . . . . . . . . . . . . . . . . . . . 1-7
PanelView 550 Features . . . . . . . . . . . . . . . . . . 1-10
PanelView 600 Features . . . . . . . . . . . . . . . . . . 1-16
PanelView 900/1000 Features . . . . . . . . . . . . . 1-22
PanelView 1400 Features . . . . . . . . . . . . . . . . . 1-26
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-30
Configuration Mode Menu . . . . . . . . . . . . . . . . 1-32
Terminal Messages . . . . . . . . . . . . . . . . . . . . . . 1-32
Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32
Alarm List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-33
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-34
Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 1-36
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . 2-1
Wiring and Safety Guidelines . . . . . . . . . . . . . . . 2-1
Connecting AC Power . . . . . . . . . . . . . . . . . . . . 2-2
Connecting DC Power . . . . . . . . . . . . . . . . . . . . 2-5
Resetting the Terminal . . . . . . . . . . . . . . . . . . . . 2-7
Power-up Sequence . . . . . . . . . . . . . . . . . . . . . . . 2-8
Publication 2711-6.1
ii
Table of Contents
Configuring the Terminal
Using a Memory Card
Running Applications
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . 3-1
Application Settings . . . . . . . . . . . . . . . . . . . . . . 3-1
Accessing the Configuration Mode Menu . . . . . 3-2
Selecting a Language . . . . . . . . . . . . . . . . . . . . . 3-4
Using a Memory Card . . . . . . . . . . . . . . . . . . . . . 3-5
Configuring Communications . . . . . . . . . . . . . . . 3-6
DH-485 Communications . . . . . . . . . . . . . . . . 3-6
DH+ Communications . . . . . . . . . . . . . . . . . . 3-8
Remote I/O Communications . . . . . . . . . . . . . 3-9
ControlNet Communications. . . . . . . . . . . . . 3-10
DeviceNet Communications . . . . . . . . . . . . . 3-12
DF1 Communications . . . . . . . . . . . . . . . . . . 3-14
Configuring Presets . . . . . . . . . . . . . . . . . . . . . . 3-16
Viewing Terminal Information . . . . . . . . . . . . . 3-17
Adjusting Screen Parameters . . . . . . . . . . . . . . 3-18
Setting the Time and Date . . . . . . . . . . . . . . . . . 3-25
Setting up the Printer . . . . . . . . . . . . . . . . . . . . . 3-26
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . 4-1
Supported Memory Cards . . . . . . . . . . . . . . . . . . 4-1
Using the Memory Card Retainer . . . . . . . . . . . . 4-2
Loading Application from a Memory Card . . . . 4-4
Loading Application on a Memory Card . . . . . . 4-6
Storing Font Files on a Memory Card . . . . . . . . 4-8
Removing a Memory Card . . . . . . . . . . . . . . . . . 4-8
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . 5-1
Application Information . . . . . . . . . . . . . . . . . . . 5-1
Push Button Operation . . . . . . . . . . . . . . . . . . . . 5-2
Control Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Numeric Entry Controls . . . . . . . . . . . . . . . . . . . 5-6
ASCII Entry Controls . . . . . . . . . . . . . . . . . . . . . 5-8
Screen Selectors . . . . . . . . . . . . . . . . . . . . . . . . 5-12
List Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
Multistate Indicators . . . . . . . . . . . . . . . . . . . . . 5-14
Bar Graph Displays . . . . . . . . . . . . . . . . . . . . . . 5-14
Numeric Data Displays . . . . . . . . . . . . . . . . . . . 5-15
Message Displays . . . . . . . . . . . . . . . . . . . . . . . 5-15
Time or Date . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
Publication 2711-6.1
Installing the PV300 Terminal
Table of Contents
iii
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . 6-1
Hazardous Locations . . . . . . . . . . . . . . . . . . . . . . 6-1
Enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . 6-2
Cutout Dimensions . . . . . . . . . . . . . . . . . . . . . . . 6-2
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Installing the PV300 in a Panel . . . . . . . . . . . . . . 6-4
Installing the PV550 Terminal
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . 7-1
Hazardous Locations . . . . . . . . . . . . . . . . . . . . . . 7-1
Enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . 7-2
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Cutout Dimensions . . . . . . . . . . . . . . . . . . . . . . . 7-4
Installing the PV550 in a Panel . . . . . . . . . . . . . . 7-5
Installing the PV600 Terminal
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . 8-1
Hazardous Locations . . . . . . . . . . . . . . . . . . . . . . 8-1
Enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . 8-2
Cutout Dimensions . . . . . . . . . . . . . . . . . . . . . . . 8-3
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
Installing the PV600 in a Panel . . . . . . . . . . . . . . 8-5
Installing the PV900/1000
Terminals
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . 9-1
Hazardous Locations . . . . . . . . . . . . . . . . . . . . . . 9-1
Enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . 9-2
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4
Cutout Dimensions . . . . . . . . . . . . . . . . . . . . . . . 9-5
Installing the PV900/PV1000 in a Panel . . . . . . . 9-6
Publication 2711-6.1
iv
Table of Contents
Installing the PV1400
Terminal
Making Terminal
Connections
Troubleshooting and
Maintenance
Appendix A
Appendix B
Appendix C
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . 10-1
Enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Mounting Dimensions . . . . . . . . . . . . . . . . . . . . 10-2
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
Cutout Dimensions . . . . . . . . . . . . . . . . . . . . . . 10-4
Installing the PV1400 in a Panel . . . . . . . . . . . . 10-5
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . 11-1
Wiring and Safety Guidelines . . . . . . . . . . . . . . 11-1
Remote I/O Terminal Connections . . . . . . . . . . 11-2
DH-485 Terminal Connections . . . . . . . . . . . . . 11-6
DH+ Terminal Connections . . . . . . . . . . . . . . 11-13
RS-232 Terminal Connections . . . . . . . . . . . . 11-16
ControlNet Connections . . . . . . . . . . . . . . . . . 11-20
DeviceNet Terminal Connections . . . . . . . . . . 11-25
DF1 Terminal Connections . . . . . . . . . . . . . . . 11-27
Connecting a Computer/Printer to the Terminal 11-30
Chapter Objectives . . . . . . . . . . . . . . . . . . . . . 12-31
Equipment Required . . . . . . . . . . . . . . . . . . . . 12-31
Using the Troubleshooting Chart . . . . . . . . . . 12-31
Replacing the Clock Module . . . . . . . . . . . . . . 12-35
Replacing the Backlight . . . . . . . . . . . . . . . . . 12-35
Specifications
Messages, Codes and Self-Test Numbers B-1
European Union Directive Compliance C-1
Glossary
Index
Publication 2711-6.1
Preface
Preface
Read this preface to familiarize yourself with the rest of this manual.
• contents of this manual
• intended audience
• conventions used
• terminology
• installing PanelView terminals
• European Union Directive Compliance
• related publications
• technical support
Publication 2711-6.1
P-2
Preface
Contents of Manual
The following table gives an overview of this manual.
Chapter
1
2
3
4
5
6
7
8
9
10
11
12
Title
Terminal Overview
Initial Setup
Configuring the Terminal
Using a Memory Card
Running Applications
Installing the PanelView 300
Terminal
Installing the PanelView 550
Terminal
Installing the PanelView 600
Terminal
Installing the
PanelView 900/1000 terminal
Installing the PanelView 1400
Terminal
Making Terminal Connections
Troubleshooting and
Maintenance
Purpose
Describes features of the PanelView terminals.
Describes how to apply power and reset the PanelView terminals.
Shows how to configure the terminal using the Configuration Mode menu.
Tells how to copy applications to and from a memory card.
Describes objects common to most applications.
Describes enclosure or panel mounting of the PanelView 300 terminal.
Describes enclosure or panel mounting of the PanelView 550 terminal.
Describes enclosure or panel mounting of the PanelView 600 terminal.
Describes enclosure or panel mounting of the PanelView 900/1000 terminal.
Describes enclosure or panel mounting of the PanelView 1400 terminal.
Describes connections for the
Remote I/O, DH-485, DH+, RS-232,
DF1, ControlNet and DeviceNet versions of the PanelView terminals.
Also shows how to connect a computer or printer to terminals with an RS-232 serial port.
Provides assistance in identifying and correcting common operating problems. Also gives procedures for routine maintenance.
Publication 2711-6.1
Intended Audience
Conventions
Terminology
Installing PanelView Terminals
European Union Directive
Compliance
Preface
P-3
No special knowledge is required to understand this manual or operate the PanelView terminals. Before running an application, you must know the functions of all screens and screen objects. This information is available from the application designer.
Equipment installers must be familiar with standard panel installation techniques.
The manual uses the following conventions:
• PV300 refers to the PanelView 300 terminal.
• PV550 refers to the PanelView 550 terminal.
• PV600 refers to the PanelView 600 terminal.
• PV900 refers to the PanelView 900 terminal.
• PV1000 refers to the PanelView 1000 terminal.
• PV1400 refers to the PanelView 1400 terminal.
• PanelView terminal refers to any one of the PanelView terminals.
This manual contains some terms that may be unfamiliar. Use the glossary of this manual for assistance.
Each terminal is shipped with installation instructions and a panel cutout. Please follow these instructions when installing your
PanelView terminal in a panel or enclosure.
Refer to Appendix C for details on installing the PanelView terminals in industrial environments requiring compliance with European
Union Directives.
Publication 2711-6.1
P-4
Preface
Related Publications
Technical Support
Refer to extensive online help for the PanelBuilder32 software or the following publications if necessary.
Publication
2711-6.19
2711-6.20
2711-6.3
2711-6.9
2711-6.0.4
2711-6.10
2711-805
1770-4.1
1770-6.2.2
1785-5.7
Description
PanelBuilder32 Software Getting Results Manual
PanelBuilder32 Quick Start Manual
PROFIBUS DP Communications for PanelView Terminals
Modbus Communications for PanelView Terminals
DeviceNet Communications for PanelView Terminals
ControlNet Communications for PanelView Terminals
PanelView File Transfer Utility
Programmable Controller Wiring and Grounding Guidelines
Data Highway/Data Highway Plus/Data Highway-485
Cable Installation Manual
Enhanced PLC-5 Programmable Controllers Installation
Instructions
For information relating to your controller, refer to the appropriate manual.
If you have questions about the PanelView terminals or the
PanelBuilder32 software, please refer to the online manuals or online help provided with the PanelBuilder32 installation CD. These publications are also available from the Automation Bookstore or Manuals
Online at the www.ab.com website.
If you can’t find the answer, contact Rockwell Automation Technical support:
Rockwell International
Technical Support
6680 Beta Drive
Mayfield Village, Ohio 44143
Or call 1-440-646-7800, 1-440-646-5800 or fax 1-440-646-7801 for technical support between 8 AM and 8 PM, Monday through Friday.
Frequently Asked Questions
Documents asking frequently asked questions are available from:
• AutoFax service at 1-440-646-5436
• www.ab.com/support and then Knowledge Base.
Firmware Upgrades
To receive firmware upgrades for your PanelView terminal:
• locate on PanelBuilder32 installation CD.
• access www.ab.com/support and download the upgrade by selecting Downloads.
Publication 2711-6.1
Chapter Objectives
Intended Uses
Terminal Types
Chapter
1
Terminal Overview
This chapter gives an overview of the PanelView Operator Terminals.
• intended uses
• terminal types and features
• applications
• configuration mode
• terminal messages
• printing
• accessories and replacement parts
You can use the PanelView operator terminals for a wide variety of machine control and monitoring applications.
!
ATTENTION: Do not use a PanelView terminal for emergency stops or other controls critical to the safety of personnel or equipment. Use separate hardwired operator interface devices that do not depend on solid state electronics. See the inside front cover of this manual for guidelines.
PanelView terminals are available in a variety of options.
• display size and type (monochrome, grayscale, color)
• operator input (touch screen or keypad)
• communication port (DH-485, RS-232, Remote I/O, DH+,
ControlNet, DeviceNet, DF1)
• RS-232 printer port support
In addition, some terminals are available with:
• AC or DC power (L1 at the end of a catalog number indicates a
DC terminal, for example, 2711-B5A1L1, or -T9C1L1).
• Stainless steel bezel available on PanelView 550 keypad or keypad & touch terminals.
Contact your Allen-Bradley representative for availability.
Publication 2711-6.1
1-2
Terminal Overview
Color and Grayscale Terminals
Color terminals support a fixed palette of 16 standard EGA colors.
Grayscale terminals support a fixed palette of 4 colors (shades of gray). All color in an application is defined when the application is created. Colors are not selectable at the terminal.
PanelView 300 Monochrome Terminals
The PanelView 300 terminal is only available with 24V dc input power.
Operator
Input
Keypad
Communication Ports
RIO DH-485 RS-232 DH+ DeviceNet ControlNet DF1 x x x x
Printer
Port
RS-232 x
Catalog
Number
2711-K3A2L1
2711-K3A5L1
2711-K3A10 L1
2711-K3A17L1
Publication 2711-6.1
Terminal Overview
1-3
PanelView 550 Monochrome Terminals
The Touch Screen version of the PanelView 550 terminal is available only with 24V dc power. The L1 in the catalog number indicates DC power.
Operator
Input
Touch Screen and Keypad
Keypad
Touch
Screen
(24V dc only)
Communication Ports
RIO DH-485 RS-232 DH+ DeviceNet ControlNet DF1 x x x x x x x x x x x x x x x x x x x x x x x x x x x
Printer Port
RS-232 x x x x x x x x x x x x x x x x x x x x x
Catalog
1
Number
2711-B5A1
2711-B5A2
2711-B5A3
2711-B5A5
2711-B5A8
2711-B5A9
2711-B5A10
2711-B5A15
2711-B5A16
2711-K5A1
2711-K5A2
2711-K5A3
2711-K5A5
2711-K5A8
2711-K5A9
2711-K5A10
2711-K5A15
2711-K5A16
2711-T5A1L1
2711-T5A2L1
2711-T5A3L1
2711-T5A5L1
2711-T5A8L1
2711-T5A9L1
2711-T5A10L1
2711-T5A15L1
2711-T5A16L1
1
Add L1 to the end of a catalog number for 24V dc power.
Add L2 to the end of a catalog number for stainless steel. Not available for the touch screen terminals.
Add L3 to the end of a catalog number for 24V dc power and stainless steel.
Stainless steel is not available for the touch screen terminals.
Publication 2711-6.1
1-4
Terminal Overview
PanelView 600 Color Terminals
Operator
Input
Touch Screen and Keypad
Keypad
Touch Screen
(24V dc only)
RIO DH-485 RS-232 DH+ DeviceNet ControlNet DF1 x x x x x x x x x x x x x x x x x x x x x x x x x x x
1
Communication Ports
Printer Port
RS-232 x x x x x x x x x x x x x x x x x x x x x
L1 added to the end of a catalog number indicates 24V dc power.
Catalog
1
Number
2711-B6C1
2711-B6C2
2711-B6C3
2711-B6C5
2711-B6C8
2711-B6C9
2711-B6C10
2711-B6C15
2711-B6C16
2711-K6C1
2711-K6C2
2711-K6C3
2711-K6C5
2711-K6C8
2711-K6C9
2711-K6C10
2711-K6C15
2711-K6C16
2711-T6C1L1
2711-T6C2L1
2711-T6C3L1
2711-T6C5L1
2711-T6C8L1
2711-T6C9L1
2711-T6C10L1
2711-T6C15L1
2711-T6C16L1
Publication 2711-6.1
Terminal Overview
1-5
PanelView 900 Monochrome Terminals
Operator
Input
Touch Screen
Keypad
1
Communication Ports
RIO DH-485 RS-232 DH+ DeviceNet ControlNet DF1 x x x x x x x x x x x x x x x x x x
Printer Port
RS-232 x x x x x x x x x x x x x x
L1 added to the end of a catalog number indicates 24V dc power.
Catalog
1
Number
2711-T9A1
2711-T9A2
2711-T9A3
2711-T9A5
2711-T9A8
2711-T9A9
2711-T9A10
2711-T9A15
2711-K5A16
2711-K9A1
2711-K9A2
2711-K9A3
2711-K9A5
2711-K9A8
2711-K9A9
2711-K9A10
2711-K9A15
2711-K9A16
PanelView 900 Color Terminals
Operator
Input
Communication Ports
Touch Screen
Keypad
RIO DH-485 RS-232 DH+ DeviceNet ControlNet DF1 x x x x x x x x x x x x x x
1
L1 added to the end of a catalog number indicates 24V dc power.
x x x x x x x x x x x x x x
Printer Port
RS-232
Catalog
1
Number
2711-T9C1
2711-T9C3
2711-T9C8
2711-T9C9
2711-T9C10
2711-T9C15
2711-T9C16
2711-K9C1
2711-K9C3
2711-K9C8
2711-K9C9
2711-K9C10
2711-K9C15
2711-K9C16
Publication 2711-6.1
1-6
Terminal Overview
PanelView 1000 Color Terminals
Operator
Input
Touch Screen
Keypad
Communication Ports
RIO DH-485 RS-232 DH+ DeviceNet ControlNet DF1 x x x x x x x x x x x x x x
Printer Port
RS-232 x x x x x x x x x x x x x x
Catalog
1
Number
2711-T10C1
2711-T10C3
2711-T10C8
2711-T10C9
2711-T10C10
2711-T10C15
2711-T10C16
2711-K10C1
2711-K10C3
2711-K10C8
2711-K10C9
2711-K10C10
2711-K10C15
2711-K10C16
1
L1 added to the end of a catalog number indicates 24V dc power.
PanelView 1000 Grayscale Terminals
Operator
Input
Touch Screen
Keypad
Communication Ports
RIO DH-485 RS-232 DH+ DeviceNet ControlNet DF1 x x x x x x x x x x x x x x
Printer Port
RS-232 x x x x x x x x x x x x x x
Catalog
1
Number
2711-T10G1
2711-T10G3
2711-T10G8
2711-T10G9
2711-T10G10
2711-T10G15
2711-T10G16
2711-K10G1
2711-K10G3
2711-K10G8
2711-K10G9
2711-K10G10
2711-K10G15
2711-K10G16
1
L1 added to the end of a catalog number indicates 24V dc power.
Publication 2711-6.1
Terminal Overview
1-7
PanelView 1400 Color Terminals
Operator
Input
Touch Screen
Keypad
Communication Ports
RIO DH-485 RS-232 DH+ DeviceNet ControlNet DF1 x x x x x x x x x x x x x x
Printer Port
RS-232 x x x x x x x x x x x x x x
Catalog
1
Number
2711-T14C1
2711-T14C3
2711-T14C8
2711-T14C9
2711-T14C10
2711-T14C15
2711-T14C16
2711-K14C1
2711-K14C3
2711-K14C8
2711-K14C9
2711-K14C10
2711-K14C15
2711-K14C16
Publication 2711-6.1
1-8
Terminal Overview
PanelView 300 Features
This section defines features of the PanelView 300 keypad terminal.
PanelView 300 Features (Front)
4
1
3
2
#
1
2
3
4
Feature
Function Keys
(F1 - F8)
Cursor Keys
Numeric Entry Keys
Keypad
Terminal Display
Description
Use the function keys to initiate functions on the terminal display. These keys may have custom legends.
Use the cursor keys to move the cursor in displayed lists, to select a numeric entry object, or to enter configuration mode.
.
0-9
-
←
↵
Enters numeric values.
Enters a decimal point.
Enters a negative value.
Clears entered digits or cancels the scratchpad.
Stores an entered value.
Initiate the function of a displayed object, such as an
ON or OFF push button, by pressing the corresponding function key (F1 - F8).
Publication 2711-6.1
DeviceNet with RS-232 Port
PanelView 300 Features (Back)
3
4
Terminal Overview
5
10 12
DH-485 Version without RS-232 Port
2
1
6
7
8
DF1 or RS-232 without RS-232 Port
7, 8, 9, 10, 11, 12
1-9
9 or 11
#
5
6
7
3
4
1
2
8
9
10
11
12
Feature
Nameplate Label
Sealing Gasket
COMM LED (Green)
FAULT LED (Red)
Memory Card Slot
Power Connection Terminals
DH-485 Communication Port
DH-485
Programming Connector
RS-232 Communication Port
DeviceNet Connector
DF1 Communication Port
RS-232 Printer/
File Transfer Port
Description
Provides product information.
Seals the front of the terminal to an enclosure or panel.
Indicates when communications is occurring.
Indicates firmware or hardware faults.
Accepts a memory card which stores applications.
Connects to external power source.
Connects to an SLC controller, DH-485 network, or Wallmount
Power Supply (Cat. No. 1747-NP1).
Connects to a Personal Computer Interface Converter (Cat. No.
1747-PIC) for transferring applications. Also connects to an SLC programmer, such as the Hand-Held Terminal (Cat. No. 1747-PT1).
Connects to the Channel 0 port of an SLC 5/03 or 5/04 controller for point-to-point DH-485 communications. Connects to a MicroLogix controller through an AIC+ Link Coupler. Also connects to the RS-
232 serial port of a computer for transferring applications.
Channel 0 Port is configured for DH-485 communications using the
Advanced Programming Software.
Connects to a DeviceNet network.
Connects to a PLC, SLC or MicroLogix controller with a DF1 port.
Connects to a printer (K3A10L1 version only).
On a DeviceNet terminal, this port also connects to the RS-232 port of a computer for transferring applications.
Publication 2711-6.1
1-10
Terminal Overview
PanelView 550 Features
4
This section defines features of the PanelView 550 terminals.
PanelView 550 Features (Front) yp
3
Cell 1
Cell 113
5
6
1
2
Keypad & Touch Screen Terminal
Cell 16
Cell 128
Touch Screen Terminal
Cell 1
5
6
Cell 113
Cell 16
Cell 128
Publication 2711-6.1
Terminal Overview
1-11
#
1
2
3
4
5
6
Feature
Function Keys
(F1 - F10)
Cursor Keys
Numeric Entry Keys
Keypad
Terminal Display
Touch Screen
Terminal Display
Touch Cells
(Touch Screen terminal)
Description
On keypad terminals, use the function keys to initiate functions on the terminal display. These keys may have custom legends.
On keypad & touch screen terminals, you can initiate functions using the function keys and/or touch screen objects.
Use the cursor keys to move the cursor in displayed lists, to select a numeric entry object, or to enter configuration mode.
.
0-9
-
←
↵
Enters numeric values.
Enters a decimal point.
Enters a negative value.
Clears entered digits or cancels the scratchpad.
Stores an entered value.
On keypad terminals, initiate the function of a displayed object, such as an ON or OFF push button, by pressing a function key (F1 - F10).
On touch screen or keypad & touch screen terminals, initiate the function of a displayed object, such as an ON or OFF push button, by touching the screen object.
Each interactive screen object occupies one or more of
128 cells.
On keypad & touch screen terminals, you can initiate functions using the function keys and/or touch screen objects.
The 128 touch cells (16 columns x 8 rows) let you initiate functions by touching the screen. Interactive screen objects are aligned with touch cells when the application is created.
Publication 2711-6.1
1-12
Terminal Overview
3
2
PanelView 550 Keypad or Keypad & Touch Screen Terminals (Back)
DH-485 Version without RS-232 Port
4
5
6
7
1
AC connector shown,
DC connector looks different
DH-485 Version with RS-232 Port
11
10
8
9
18
11
RS-232 Version
10
Backlight lamp behind access cover
Remote I/O, DH+, DeviceNet, ControlNet or
DF1 Version with RS-232 Port
13, 14, 15, 16 or 17
18
18
12
RS-232 Version with additional RS-232 Port
12
Publication 2711-6.1
Terminal Overview
1-13
#
7
8
5
6
3
4
1
2
9
10
11
12
13
14
15
16
17
18
Feature
Power Connection Terminals
Nameplate Label
Sealing Gasket
COMM LED (Green)
FAULT LED (Red)
Memory Card Slot
Access Cover
Backlight Lamp
Spare Bulb Holder
DH-485 Communication Port
DH-485
Programming Connector
RS-232 Communication Port
Remote I/O Port
DH+ Communication Port
DeviceNet Connector
ControlNet Connectors
DF1 Communication Port
RS-232 Printer/
File Transfer Port
Description
Connects to external power source.
Provides product information.
Seals the front of the terminal to an enclosure or panel.
Indicates when communications is occurring.
Indicates firmware or hardware faults.
Accepts a memory card which stores applications.
Provides access to the replaceable backlight lamp.
Light source for the display backlight. Light transmits through a fiberoptic bundle to the back of the LCD display.
Stores a spare backlight lamp.
Connects to an SLC or MicroLogix controller, DH-485 network, or
Wallmount Power Supply (Cat. No. 1747-NP1).
Connects to a Personal Computer Interface Converter (Cat. No.
1747-PIC) for transferring applications. Also connects to an SLC programmer, such as the Hand-Held Terminal (Cat. No. 1747-PT1).
Connects to the Channel 0 port of an SLC 5/03 or 5/04 controller for point-to-point DH-485 communications. Connects to a MicroLogix controller through an AIC+ Link Coupler. Also connects to the RS-
232 serial port of a computer for transferring applications.
Channel 0 Port is configured for DH-485 communications using the
Advanced Programming Software.
Connects to a scanner or sub-scanner on a Remote I/O network.
Connects to a PLC or SLC 5/04 controller on a DH+ link.
Connects to a DeviceNet network.
Connects to a ControlNet network.
Connects to a PLC, SLC or MicroLogix controller with a DF1 port.
Connects to a printer.
On Remote I/O, DH+, DF1, DeviceNet and ControlNet terminals, this port also connects to the RS-232 port of a computer for transferring applications.
Publication 2711-6.1
1-14
Terminal Overview
4
3
2
PanelView 550 Touch Screen Terminal Features (Back)
DH-485 Version without RS-232 Port
5
6
7
1
DH-485 Version with RS-232 Port
11
10
9
8
Backlight lamp behind access cover
9
11
10
18
RS-232 Version
Remote I/O, DH+, DeviceNet, ControlNet or
DF1 Version with RS-232 Port
12
RS-232 Version with additional RS-232 Port
18
13, 14, 15, 16 or 17
12
18
Publication 2711-6.1
Terminal Overview
1-15
#
7
8
5
6
3
4
1
2
9
10
11
12
13
14
15
16
17
18
Feature
Power Connection Terminals
Sealing Gasket
FAULT LED (Red)
COMM LED (Green)
Nameplate Label
Memory Card Slot
Reset Button
Access Cover
Backlight Lamp
DH-485 Communication Port
DH-485
Programming Connector
RS-232 Communication Port
Remote I/O Port
DH+ Communication Port
DeviceNet Connector
ControlNet Connectors
DF1 Communication Port
RS-232 Printer/
File Transfer Port
Description
Connects to external DC power source.
Seals the front of the terminal to an enclosure or panel.
Indicates firmware or hardware faults.
Indicates when communications is occurring.
Provides product information.
Accepts a memory card which stores applications.
Resets the terminal.
Provides access to the replaceable backlight lamp.
Light source for the display backlight.
Connects to an SLC or MicroLogix controller, DH-485 network, or
Wallmount Power Supply (Cat. No. 1747-NP1).
Connects to a Personal Computer Interface Converter (Cat. No.
1747-PIC) for transferring applications. Also connects to an SLC programmer, such as the Hand-Held Terminal (Cat. No. 1747-PT1).
Connects to the Channel 0 port of an SLC 5/03 or 5/04 controller for point-to-point DH-485 communications. Connects to a MicroLogix controller through an AIC+ Link Coupler. Also connects to the RS-
232 serial port of a computer for transferring applications.
Channel 0 Port is configured for DH-485 communications using the
Advanced Programming Software.
Connects to a scanner or sub-scanner on a Remote I/O network.
Connects to a PLC or SLC 5/04 controller on a DH+ link.
Connects to a DeviceNet network.
Connects to a ControlNet network.
Connects to a PLC, SLC or MicroLogix controller with a DF1 port.
Connects to a printer.
On Remote I/O, DH+, DF1, DeviceNet or ControlNet terminals, this port also connects to the RS-232 port of a computer for transferring applications.
Publication 2711-6.1
1-16
Terminal Overview
PanelView 600 Features
This section defines features of the PanelView 600 terminals.
PanelView 600 Features (Front)
Keypad Terminal
3
4
Cell 1
5
6
Cell 113
1
2
Keypad & Touch Screen Terminal
Cell 16
Cell 128
Cell 1
5
6
Cell 113
Touch Screen Terminal
Cell 16
Cell 128
Publication 2711-6.1
Terminal Overview
1-17
#
1
2
3
4
5
6
Feature
Function Keys (F1 - F10)
Cursor Keys
Numeric Entry Keys
Keypad Terminal Display
Touch Screen
Terminal Display
Touch Cells
(Touch Screen terminal)
Description
Use the function keys on keypad terminals to initiate functions on the terminal display. These keys may have custom legends.
On the keypad & touch screen terminals, you can initiate functions using the function keys and/or touch screen objects.
Use the cursor keys to move the cursor in displayed lists, to select a numeric entry object, or to enter configuration mode.
.
0-9
-
←
↵
Enters numeric values.
Enters a decimal point.
Enters a negative value.
Clears entered digits or cancels the scratchpad.
Stores an entered value.
On keypad terminals, initiate the function of a displayed object, such as an ON or OFF push button, by pressing a function key (F1 - F10).
On keypad & touch screen terminals, initiate the function of a displayed object, such as an ON or OFF push button, by touching the screen object. Each interactive screen object occupies one or more of 128 cells.
On touch screen & keypad terminals, you can initiate functions, using the function keys and/or touch screen objects.
The 128 touch cells (16 columns x 8 rows) let you initiate functions by touching the screen. Interactive screen objects are aligned with touch cells when the application is created.
Publication 2711-6.1
1-18
Terminal Overview
PanelView 600 Keypad or Keypad & Touch Screen Terminal (Back)
Remote I/O, DH+, DeviceNet, ControlNet or DF1 Version with RS-232 Port
4
10, 11, 12, 13 or 14
15
DH-485 Version
3
2
7
8
DH-485 Version with RS-232 Port
1
7, 8, 9, 10
11, 12, 13, 14, 15
6
5
15 7 8
RS-232 Version
9
RS-232 Version with additional RS-232 Port
15
9
Publication 2711-6.1
Terminal Overview
1-19
#
5
6
7
3
4
1
2
8
9
10
11
12
13
14
15
Feature
Power Connection Terminals
Nameplate Label
Memory Card Slot
Sealing Gasket
FAULT LED (Red)
COMM LED (Green)
DH-485 Communication Port
DH-485
Programming Connector
RS-232 Communication Port
Remote I/O Port
DH+ Communication Port
DeviceNet Connector
ControlNet Connectors
DF1 Communication Port
RS-232 Printer/
File Transfer Port
Description
Connects to external power source.
Provides product information.
Accepts a memory card which stores applications.
Seals the front of the terminal to an enclosure or panel.
Indicates firmware or hardware faults.
Indicates when communications is occurring.
Connects to an SLC or MicroLogix controller, DH-485 network, or
Wallmount Power Supply (Cat. No. 1747-NP1).
Connects to a Personal Computer Interface Converter (Cat. No.
1747-PIC) for transferring applications. Also connects to an SLC programmer, such as the Hand-Held Terminal (Cat. No. 1747-PT1).
Connects to the Channel 0 port of an SLC 5/03 or 5/04 controller for point-to-point DH-485 communications. Connects to a MicroLogix controller through an AIC+ Link Coupler. Also connects to the RS-
232 serial port of a computer for transferring applications.
Channel 0 Port is configured for DH-485 communications using the
Advanced Programming Software.
Connects to a scanner or sub-scanner on a Remote I/O network.
Connects to a PLC or SLC 5/04 controller on a DH+ link.
Connects to a DeviceNet network.
Connects to a ControlNet network.
Connects to a PLC, SLC or MicroLogix controller with a DF1 port.
Connects to a printer.
On Remote I/O, DH+, DF1, DeviceNet or ControlNet terminals, this port also connects to the RS-232 port of a computer for transferring applications.
Publication 2711-6.1
1-20
Terminal Overview
PanelView 600 Touch-Screen Terminal Features (Back)
Remote I/O, DH+, DeviceNet, ControlNet or DF1 Version with RS-232 Port
5
11, 12, 13, 14 or 15
16
DH-485 Version
4
3
2
1
8
9
DH-485 Version with RS-232 Port
8, 9, 10, 11
12, 13, 14, 15, 16
7
6
16
8
RS-232 Version
9
10
RS-232 Version with additional RS-232 Port
16 10
Publication 2711-6.1
Terminal Overview
1-21
#
7
8
5
6
3
4
1
2
9
10
11
12
13
14
15
16
Feature Description
Power Connection Terminals
Nameplate Label
Fault LED (Red)
COMM LED (Green)
Connects to external power source.
Provides product information.
Indicates firmware or hardware faults.
Indicates when communications is occurring.
Sealing Gasket
Reset Button
Memory Card Slot
Accepts a memory card which stores applications.
DH-485 Communications Port
Connects to an SLC controller, DH-485 network, or Wallmount
Power Supply (Cat. No. 1747-NP1).
DH-485
Programming Connector
Seals the front of the terminal to an enclosure or panel.
Resets the terminal.
RS-232 Communication Port
Connects to a Personal Computer Interface Converter (Cat. No.
1747-PIC) for transferring applications. Also connects to an SLC programmer, such as the Hand-Held Terminal (Cat. No. 1747-PT1).
Connects to the Channel 0 port of an SLC 5/03 or 5/04 controller for point-to-point DH-485 communications. Connects to a MicroLogix controller through an AIC+ Link Coupler. Also connects to the RS-
232 serial port of a computer for transferring applications.
Channel 0 Port is configured for DH-485 communications using the
Advanced Programming Software.
Remote I/O Port
DH+ Communication Port
DeviceNet Connector
ControlNet Connectors
DF1 Communication Port
RS-232 Printer/
File Transfer Port
Connects to a scanner or sub-scanner on a Remote I/O network.
Connects to a PLC or SLC 5/04 controller on a DH+ link.
Connects to a DeviceNet network.
Connects to a ControlNet network.
Connects to a PLC, SLC or MicroLogix controller with a DF1 port.
Connects to a printer.
On Remote I/O, DH+, DF1, DeviceNet or ControlNet terminals, this port also connects to the RS-232 port of a computer for transferring applications.
Publication 2711-6.1
1-22
Terminal Overview
PanelView 900/1000 Features
This section defines features of the PanelView 900 and 1000 terminals.
PanelView 900/1000 Terminal Features (Front)
Keypad Terminal
4
Cell 1
5
6
Cell 361
1
2
Touch Screen Terminal
3
Cell 24
Cell 384
Publication 2711-6.1
Terminal Overview
1-23
#
1
2
3
4
5
6
Feature Description
Function Keys (F1 - F16)
Cursor Keys
Numeric Entry Keys
Keypad Terminal Display
Touch Screen
Terminal Display
Touch Cells
(Touch Screen terminal)
Use the function keys on keypad terminals to initiate functions on the terminal display. These keys may have custom legends.
Use the cursor keys to move the cursor in displayed lists, to select a numeric entry object or to enter configuration mode.
.
0-9
-
←
↵
Enters numeric values.
Enters a decimal point.
Enters a negative value.
Clears entered digits or cancels the scratchpad.
Stores an entered value.
On keypad terminals, initiate the function of a displayed object, such as an ON or OFF push button, by pressing a function key (F1 - F16).
On touch screen terminals, initiate the function of a displayed object, such as an ON or OFF push button, by touching the screen object. Each interactive screen object occupies one or more of 384 cells.
The 384 touch cells (24 columns x 16 rows) let you initiate functions by touching the screen. Interactive screen objects are aligned with touch cells when the application is created.
Publication 2711-6.1
1-24
Terminal Overview
PanelView 900/1000 Terminal Features (Back)
Remote I/O, DH+, DF1, DeviceNet, or ControlNet Version with RS-232 Port
4
Back View
Touch Screen Terminal
3
11, 12, 13, 14 or 15 16
2
DH-485 Version
5
6
8 9
1
8, 9, 10
11, 12, 13, 14, 15, 16
7
DH-485 Version with RS-232 Port
4
Back View
Keypad Terminal
16
8
9
RS-232 Version
3
5
6
10
2
RS-232 Version with additional RS-232 Port
1
8, 9, 10
11, 12, 13, 14, 15, 16
7
16
10
Publication 2711-6.1
Terminal Overview
1-25
#
7
8
5
6
3
4
1
2
9
10
11
12
13
14
15
16
Feature
Power Connection Terminals
Nameplate Label
Reset Button
Sealing Gasket
Memory Card Slot
FAULT LED (Red)
COMM LED (Green)
DH-485 Communication Port
DH-485
Programming Connector
RS-232 Communication Port
Remote I/O Port
DH+ Communication Port
DeviceNet Connector
ControlNet Connectors
DF1 Communication Port
RS-232 Printer/
File Transfer Port
Description
Connects to external power source.
Provides product information.
Resets the terminal.
Seals the front of the terminal to an enclosure or panel.
Accepts a memory card which stores applications.
Indicates firmware or hardware faults.
Indicates when communications is occurring.
Connects to an SLC or MicroLogix controller, DH-485 network, or
Wallmount Power Supply (Cat. No. 1747-NP1).
Connects to a Personal Computer Interface Converter (Cat. No.
1747-PIC) for transferring applications. Also connects to an SLC programmer, such as the Hand-Held Terminal (Cat. No. 1747-PT1).
Connects to the Channel 0 port of an SLC 5/03 or 5/04 controller for point-to-point DH-485 communications. Connects to a MicroLogix controller through an AIC+ Link Coupler. Also connects to the RS-
232 serial port of a computer for transferring applications.
Channel 0 Port is configured for DH-485 communications using the
Advanced Programming Software.
Connects to a scanner or sub-scanner on a Remote I/O network.
Connects to a PLC or SLC 5/04 controller on a DH+ link.
Connects to a DeviceNet network.
Connects to a ControlNet network.
Connects to a PLC, SLC or MicroLogix controller with a DF1 port.
Connects to a printer.
On Remote I/O, DH+, DF1, DeviceNet and ControlNet terminals, this port also connects to the RS-232 port of a computer for transferring applications.
Publication 2711-6.1
1-26
Terminal Overview
PanelView 1400 Features
This section defines features of the PanelView 1400 terminals.
Panel View 1400 Terminal Features (Front)
Keypad Terminal
3
4
Cell 1
5
6
Cell 361
1
Touch Screen Terminal
2
Cell 24
Cell 384
Publication 2711-6.1
Terminal Overview
1-27
#
1
2
3
4
5
6
Feature
Function Keys (F1 - F21)
Cursor Keys
Numeric Entry Keys
Keypad Terminal Display
Touch Screen
Terminal Display
Touch Cells
(Touch Screen terminal)
Description
Use the function keys on keypad terminals to initiate functions on the terminal display. These keys may have custom legends.
Use the cursor keys to move the cursor in displayed lists, to select a numeric entry object, or to enter configuration mode.
.
0-9
-
←
↵
Enters numeric values.
Enters a decimal point.
Enters a negative value.
Clears entered digits or cancels the scratchpad.
Stores an entered value.
On keypad terminals, initiate the function of a displayed object, such as an ON or OFF push button, by pressing a function key (F1 - F21).
On touch screen terminals, initiate the function of a displayed object, such as an ON or OFF push button, by touching the screen object. Each interactive screen object occupies one or more of 384 cells.
The 384 touch cells (24 columns x 16 rows) let you initiate functions by touching the screen. Interactive screen objects are aligned with touch cells when the application is created.
Publication 2711-6.1
1-28
Terminal Overview
PanelView 1400 Terminal Features (Back and Sides)
Remote I/O, DH+, DeviceNet, ControlNet or DF1 Version with RS-232 Port
18
15
7, 8, 9
10, 11, 12
13, 14, 15
10, 11, 12, 13 or 14
17
16
DH-485 Version with RS-232 Port
6
5
Left Side
4
7
8
15
3
19
2
1
RS-232 Version with additional RS-232 Port
9
15
Right Side
20
Publication 2711-6.1
Terminal Overview
1-29
#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Feature
Brightness Control
Contrast Control
Nameplate Label
FAULT LED (Red)
COMM LED (Green)
Power Connection Terminals
DH-485 Communication Port
DH-485
Programming Connector
RS-232 Communication Port
Remote I/O Port
DH+ Communication Port
DeviceNet Connector
ControlNet Connector
DF1 Communication Port
RS-232 Printer/
File Transfer Port
Memory Card Eject Button
Memory Card Slot
Sealing Gasket
Reset Button
CRT Board Adjustments
Description
Adjusts the brightness of the color display.
Adjusts the contrast of the color display.
Provides product information.
Indicates firmware or hardware faults.
Indicates when communications is occurring.
Connects to external power source.
Connects to an SLC or MicroLogix controller, DH-485 network, or
Wallmount Power Supply (Cat. No. 1747-NP1).
Connects to a Personal Computer Interface Converter (Cat. No.
1747-PIC) for transferring applications. Also connects to an SLC programmer, such as the Hand-Held Terminal (Cat. No. 1747-PT1).
Connects to the Channel 0 port of an SLC 5/03 or 5/04 controller for point-to-point DH-485 communications. Connects to a MicroLogix controller through an AIC+ Link Coupler. Also connects to the RS-
232 serial port of a computer for transferring applications.
Connects to a scanner or sub-scanner on a Remote I/O network.
Connects to a PLC or SLC 5/04 controller on a DH+ link.
Connects to a DeviceNet network.
Connects to a ControlNet network.
Connects to a PLC, SLC or MicroLogix controller with a DF1 port.
Connects to a printer. On Remote I/O, DH+, DF1, DeviceNet or ControlNet terminals, this port also connects to the RS-232 port of a computer for transferring applications.
Ejects memory card from slot.
Accepts a memory card which stores applications.
Seals the front of the terminal to an enclosure or panel.
Resets the terminal.
See the warning below.
!
ATTENTION: Only qualified service technicians should access the CRT board adjustments. Failure to follow this caution could result in electrical shock, a misadjusted monitor, or a damaged monitor.
Publication 2711-6.1
1-30
Applications
Terminal Overview
PanelView terminals operate with custom designed applications. The first time you power on the terminal, (no application file loaded), the terminal displays the Configuration Mode menu. Chapter 3 describes the terminal functions you can configure from this menu.
Note: Remote I/O terminals provide an out-of-box application for setting Remote I/O communication parameters.
If an application is loaded, the terminal displays the application’s start-up screen.
Note: The application designer is responsible for documenting the operation of the application and selecting a startup screen.
How the terminal operates depends on the application and the type of terminal (touch screen or keypad).
Publication 2711-6.1
Terminal Overview
1-31
Touch Screen Operation
Applications for touch screen terminals are controlled by touching screen objects.
Keypad Operation
Applications for keypad terminals are controlled by pressing function keys that correspond to screen objects. Data is entered manually using the numeric entry keys.
A function key legend kit is available for each terminal to create custom labels for the function keys. See the accessories at the end of this chapter.
!
ATTENTION: Do not press multiple touch screen objects or multiple function keys at the same time. This may result in unintended operation.
Publication 2711-6.1
1-32
Terminal Overview
Configuration Mode Menu
Terminal Messages
Printing
You can configure terminal functions from the Configuration Mode menu including:
• select a language
• upload/download applications with a memory card
• set or display serial communication parameters
• select preset values
• obtain terminal and application information
• adjust screen parameters
• set time and date
• set printer parameters (for terminals with an RS-232 printer port)
• return to run mode
Chapter 3 describes how to enter configuration mode and the operations you can perform the Configuration Mode menu.
Terminals messages display:
• status of an operation
• minor faults, errors, or numeric entry mistakes
• operator prompts
Appendix B describes terminal messages and provides a list of recommended actions.
PanelView terminals equipped with an RS-232 printer port can print:
• triggered messages in a message display
• triggered states of a multistate indicator
• alarm messages
• alarm list
Print attributes for objects are defined in the application.
Any printer that supports the IBM enhanced character set can be connected to the RS-232 printer port of a PanelView terminal.
Publication 2711-6.1
Alarm List
Terminal Overview
1-33
PanelView terminals support an Alarm List queue to store information on triggered alarms. The Alarm List stores a maximum of
100 alarms or as many as the terminal can hold in nonvolatile RAM.
The number of alarms stored in the list is configured using the
PanelBuilder32 software.
The Alarm List stores the following data for each alarm:
• acknowledge indicator
• alarm date and time
• acknowledge date and time
• alarm trigger value
• alarm text including variables
The Alarm List is cleared:
• when an application is downloaded to the terminal
• when the terminal is reset or power is cycled
The Alarm List object may appear on the Alarm Banner or other application screens. The data that displays in the Alarm List is configured using the PanelBuilder32 Software.
Publication 2711-6.1
1-34
Accessories
Terminal Overview
Software
Catalog No.
300 550 600 900 1000 1400
2711-ND3
x x x x x x
Description
Windows software required for creating Panel-
View applications on a personal computer.
Function Key Legend Kits
Catalog No.
300 550 600 900 1000 1400
2711-NF1
x
2711-NF2A
2711-NF2C
2711-NF4
2711-NF5
2711-NF6
2711-NF7
x x x x x
Description
5 legend inserts with key labels F1-F10 on one side. Use blank side to create custom labels.
1 legend insert for PV900 keypad (monochrome) terminal with key labels F1-F16 on one side. Use blank side to create custom labels.
1 legend insert for PV900 keypad (color) terminal with key labels F1-F16 on one side. Use blank side to create custom labels.
1 legend insert with key labels F1-F10 on one side. Use blank side to create custom labels.
x
2 legend inserts. One has key labels F1-F16; the other has key labels F17-F21. Use blank sides to create custom labels.
1 legend insert with key labels F1-F16. Use blank side to create custom labels.
2 legend inserts with key labels F1-F4 and F5-
F8. Use blank side to create custom labels.
Memory Cards and Retainer
Catalog No.
300 550 600 900 1000 1400
2711-NM11
1
2711-NM12
1
2711-NM13
2711-NM14
2711-NM24
x x x x x x x x x x x x x x x x x x x x x x x x
2711-NM28
2711-NM216
1
2711-NMCC
2711-NMCD
2711-NMCE
x x x x x x x x x x x x x x x x x
Description x
256K memory card for storing applications.
x
1M flash memory card for storing applications.
x
2M flash memory card for storing applications.
x
4M flash memory card for storing applications.
x
4M flash ATA card for storing applications and font files.
x
8M flash ATA card for storing applications and font files.
x
8M flash ATA card for storing applications and font files.
Secures memory card in all terminals except the PV1400 and PV550 touch screen. Prevents electrostatic discharge.
Secures memory card in 550 touch screen terminal and prevents electrostatic discharge.
Secures memory card in PanelView 300 keypad and 600 touch screen terminals and prevents electrostatic discharge.
1 Contact Allen-Bradley for availability
Publication 2711-6.1
Terminal Overview
1-35
Antiglare Overlay
Self-adhesive filters are available to minimize the reflection of terminal displays.
600 900 1000 1400 Catalog No.
2711-NV4 (Keypad)
2711-NV4T (Touch Screen Terminals)
2711-NV3K (Keypad)
2711-NV3T (Touch Screen Terminals)
2711-NV5 (Keypad)
2711-NV7K (Keypad Terminals)
2711-NV7T (Touch Screen Terminals)
2711-NV6K (Keypad Terminals)
2711-NV6T (Touch Screen Terminals)
2711-NV8 (Keypad Terminals)
300 550 x x x x x x x x x x x
DH-485 Operating and Programming Cables
Catalog No.
Description
1747-PIC
1747-C10
1747-C11
Personal Computer Interface Converter converts RS-232 signals to/from
RS-485 signals. Use to transfer applications between a DH-485 terminal and a computer.
1.83 meter (6 foot) cable connects a DH-485 terminal to an SLC or DH-485 network.
0.30 meter (1 foot) cable connects a DH-485 terminal to an SLC or DH-485 network.
1747-C20
1747-CP3
6.1 meter (20 foot) cable connects a DH-485 terminal to an SLC or DH-485 network.
45 cm (17.7 inch) cable connects an RS-232 terminal to an AIC+ (Port1) through a null modem adapter.
1761-CBL-AP00 45 cm (17.7 inch) cable connects an RS-232 terminal to an AIC+ (Port2) through a null modem adapter.
1761-CBL-AC00 3 meter (9.8 foot) cable connects an RS-232 terminal to an AIC+ (Port1) through a null modem adapter.
1761-CBL-PM02 2 meter (6.5 foot) cable connects an RS-232 terminal to an AIC+ (Port2) through a null modem adapter.
1761-CBL-AS03 3 meter (9.8 foot) cable connects a DH-485 terminal to an AIC+ (Port3).
1761-CBL-AS09 9.9 meter (29.5 foot) cable connects a DH-485 terminal to an AIC+ (Port3).
PanelView File Transfer Utility
Catalog No.
2711-ND7
Description
Transfers .PVA files between a DH-485 terminal and a computer from the
DOS environment. Does not require Windows.
Power Supply and Link Couplers
The following items are available for all DH-485 PanelView terminals.
Catalog No.
Description
1747-NP1
1747-AIC
1747-NET-AIC
Wallmount Power supply provides power for DH-485 communications when an SLC or network is not connected.
AIC Link Coupler links devices on a DH-485 network.
AIC+ Link Coupler links devices on a DH-485 network including MicroLogix.
Publication 2711-6.1
1-36
Terminal Overview
Replacement Parts
RS-232 Cables
Catalog No.
2711-NC13
2711-NC14
2706-NC13
Description
5 meter (16.4 foot) connects an RS-232 terminal to the Channel 0 port of an
SLC 5/03 controller or the RS-232 port of a computer or printer.
10 meter (32.7 foot) cable connects an RS-232 terminal to the Channel 0 port of an SLC 5/03 controller or the RS-232 port of a computer or printer.
3 meter (10 ft) cable connects an RS-232 terminal to an SLC 5/03 controller or the RS-232 port of a computer or printer.
1770-CD
Remote I/O Cable
Catalog No.
Description
Shielded, 3-conductor cable (Belden 9463) for connecting a Remote I/O terminal to a Remote I/O network.
Backlight Lamps
Catalog No.
300 550 600 900 1000
2711-NL1
x
2711-NL2
2711-NL3
2711-NL4
x x
Description
Halogen backlight lamp for all PV550 terminals.
Provides backlighting for LCD display.
Backlight for PV900 color terminal.
Backlight for PV600 color terminal.
x
Backlight for PV1000 color terminal.
Real Time Clock Modules
Catalog No.
300 550 600 900 1000 1400
2711-NB2
x
2711-NB3
2711-NB4
x x x x x x x
Description
Real time clock module for PV550 (Series D or earlier). Does not apply to the PV550 touch screen terminals. Contains lithium battery.
x
Real time clock module for PV600, PV900,
PV1000, PV1400 or PV550 (Series E or later).
Does not apply to PV550 touch screen terminals. Contains lithium battery.
Real time clock module for PV300 keypad,
PV550/PV600 touch screen only terminals.
Contains lithium battery.
Panel Mount Clips and Studs
Catalog No.
300 550 600 900 1000 1400
2711-NP1
2711-NP2
x x x
2711-NP3
Description x
10 panel mount clips for PV1400 terminal.
6 panel mount clips for PV600, PV900 or
PV1000 terminals.
x
Optional panel mount studs (18) for PV1400 terminals.
Remote I/O Connector
Catalog No.
550 600 900 1000 1400
22112-046-03
x x x x x
Description
Terminal block connector plugs into Remote I/O port of Remote I/O terminals.
Publication 2711-6.1
Chapter Objectives
Wiring and Safety Guidelines
Chapter
2
Initial Setup
This chapter provides information on:
• wiring and safety guidelines
• connecting AC or DC power
• resetting the terminal
• power-up sequence
Use publication NFPA 70E, Electrical Safety Requirements for
Employee Workplaces when wiring the PanelView terminals. In addition to the NFPA general guidelines:
• connect the terminal to its own branch circuit.
The input power should be protected by a fuse or circuit breaker rated at no more than 15 Amps.
• route incoming power to the PanelView terminal by a separate path from the communications cable.
ATTENTION: Do not run signal wiring and power wiring in the same conduit.
!
• where power and communication lines must cross, they should cross at right angles. Communication lines can be installed in the same conduit as low level DC I/O lines (less than 10 volts).
Publication 2711-6.1
2-2
Initial Setup
Connecting AC Power
Below are AC electrical ratings for the PanelView terminals. The
PV550/PV600 touch screen only terminal is available only with DC power, not AC power.
Terminal Type
PV550
PV600
PV900M/PV900C
PV1000G/PV1000C
PV1400
Supply Voltage
85 to 264V ac, 47 to 63 Hz
85 to 264V ac, 43 to 63 Hz
85 to 264V ac, 47 to 63 Hz
85 to 264V ac, 47 to 63 Hz
85 to 264V ac, 43 to 63 Hz
Power Consumption
45 VA maximum
60 VA maximum
110 VA maximum
100 VA maximum
200 VA maximum
!
ATTENTION: Do not apply power to the PanelView terminal until all wiring connections have been made.
Failure to do so may result in electrical shock.
AC Power Connections
The PanelView terminals are IEC 1131-2 Equipment Class I devices and require you to connect the GND (Ground) or (Protective
Earth) terminal to an earth conductor.
!
ATTENTION: The PanelView terminals are designed for safe use when installed in a NEMA Type 12, 13, 4X
(indoor use only), IP54 or IP65 rated enclosure.
!
ATTENTION: Explosion Hazard - Do not connect or disconnect equipment while circuit is live unless area is known to be non-hazardous.
To connect power to the AC versions of the PanelView terminals:
1. Secure AC power wires to the L1 and L2N terminal block screws.
2. Secure the Earth Ground/Protective Earth wire to the GND or the screw on the terminal block.
!
ATTENTION: Improper wiring of the power terminals may result in voltage at the communication connector shells. Refer to the figure below when wiring.
3. Apply power to the terminal.
Publication 2711-6.1
PanelView 550 Terminal
PanelView 550 Terminal
Initial Setup
2-3
120/240V ac, 3 Wire,
U.S. Color Code
Black (Line)
White (Neutral)
Green (Earth Ground)
L1 L2N
GND
120/240V ac, 3 Wire,
European Harmonized Color Code
L1 L2N
GND
Brown (Line)
Blue (Neutral)
Green/Yellow (Protective Earth)
To Power Source
To Power Source
Publication 2711-6.1
2-4
Initial Setup
PanelView 900/1000 Terminal
Power Terminal
Block (fixed)
120/240V ac, 3 Wire,
U.S. Color Code
L1 L2N
GND/PE
Black (Line)
White (Neutral)
Green (Earth Ground)
120/240V ac, 3 Wire
European Harmonized Color Code
L1 L2N
GND/PE
Brown (Line)
Blue (Neutral)
Green/Yellow
(Protective
Earth)
To Power Source
To Power Source
PanelView 1400 Terminal
Screwdriver Slot
Power Terminal Block (fixed)
120/240V ac, 3 Wire,
U.S. Color Code
L2/N
L1/L
120/240V ac, 3 Wire
European Harmonized Color Code
GND/PE
L2/N
Green (Earth Ground)
White (Neutral)
Black (Line)
L1/L
Green/Yellow (Protective Earth)
Blue (Neutral)
Brown (Line)
Publication 2711-6.1
Connecting DC Power
Initial Setup
2-5
The L1 versions (Cat. No. 2711-K5A1L1, -T9C1L1) of the PV300,
PV550, PV600, PV900, and PV1000 terminals connect to a 24V dc power source.
The table below shows the electrical ratings for the DC versions of the terminals. Electronic circuitry and an internal fuse protect the terminals from reverse polarity and over-voltage conditions.
Terminal Type
PV300
PV550
PV550
(touch only)
PV600
PV600
(touch only)
PV900M
PV900C
PV1000G
PV1000C
Supply Voltage
(24V dc nominal)
18 to 32V dc
18 to 30V dc
18 to 32V dc
18 to 32V dc
18 to 32V dc
18 to 30V dc
18 to 32V dc
18 to 32V dc
18 to 32V dc
Power Consumption
18 Watts max. (0.75A @ 24V dc)
18 Watts max. (0.75A @ 24V dc)
18 Watts max. (0.75A @ 24V dc)
34 Watts max. (1.4A @ 24V dc)
17 Watts max. (0.71A @ 24V dc)
58 Watts max. (2.5A @ 24V dc)
50 Watts max. (2.1A @ 24V dc)
40 Watts max. (1.7A @ 24V dc)
50 Watts max. (2.1A @ 24V dc)
!
ATTENTION: Do not connect the PanelView terminal to an AC power source. Connecting to an AC power source may damage the terminal.
Do no
!
ATTENTION: The PanelView terminals are designed for safe use when installed in a NEMA Type 12, 13,
14X (indoor use only), IP54 or IP65 rated enclosure.
!
ATTENTION: Use only a safety extra-low voltage
(SELV) power supply as a source for the PanelView 300 or 550 touch screen terminal. A SELV power supply does not exceed 42.4V dc.
Publication 2711-6.1
2-6
Initial Setup
PanelView 300 Terminal
DC Power Connections
Connect the power source to the terminal at the 3-screw terminal block (fixed).
To connect power to the DC versions of the PanelView terminals:
1. Secure the DC power wires to the terminal block screws.
2. Secure the Earth Ground wire to the correct terminal block screw.
!
ATTENTION: Explosion Hazard - Do not connect or disconnect equipment while circuit is live unless area is known to be non-hazardous.
!
ATTENTION: Do not apply power to the PanelView terminal until all wiring connections have been made.
Failure to do so may result in electrical shock.
3. Apply 24V dc power to the terminal.
PanelView 550/600 Terminal PanelView 900/1000 Terminal
Power Terminal
Block (fixed)
+
-
Earth Ground
DC Negative
DC Positive
Power Terminal
Block (fixed)
Publication 2711-6.1
Resetting the Terminal
Initial Setup
2-7
Resetting the terminal re-initializes the PanelView terminal (same as cycling power).
To reset the PV300, PV550 (keypad, keypad & touch) or the
PV600 (keypad & touch):
Simultaneously press the Left arrow , Right arrow , and Enter
↵ keys. The terminal performs its powerup sequence.
The sequence in which keys are pressed (while running an application), determines what appears after the reset.
• If you press the Left and Right arrow keys before the Enter
↵ key, the Configuration Mode menu appears.
• If you press the Enter
↵
=key before the arrow keys, the terminal runs the loaded application.
To reset the PV550/PV600 (touch only)/PV900/PV1000/PV1400:
• Use a narrow non-conductive tool to press the reset button shown below. The terminal performs its powerup sequence.
!
ATTENTION: Use a nonconducting object to press the Reset button. Do not use a conducting object such as a paper clip which may damage the terminal. Do not use the tip of a pencil, graphite may damage the terminal.
PanelView 900/1000
PanelView 1400
Reset Button
On the PV550/PV600 touch screen terminals, the Reset button is located on the right, below the Memory Card slot.
Publication 2711-6.1
2-8
Initial Setup
Power-up Sequence
When resetting or applying power to a PanelView terminal, the terminal runs a series of self-tests. The initial display shows copyright information and the status of each self-test number. See Appendix B for a description of the self-test numbers.
COPYRIGHT ALLEN-BRADLEY COMPANY
1999, ALL RIGHTS RESERVED VXX.XX
TESTING VERIFICANADO PRUFEN
VERIFICATION AUTOTEST
2
Self-test Number
For DH-485 and RS-232 Terminals
• If an application is loaded, the terminal displays either the screen that was present prior to reset or power down, or the startup screen.
• If an application is not loaded, the Configuration Mode menu appears.
PV900 Keypad Terminal
Note: On PV550/600 terminals, the Reset Video Button is F9.
Function keys do not appear on touch screen terminals.
Publication 2711-6.1
Initial Setup
2-9
For Remote I/O Terminals
An out-of-box application screen opens allowing you to set Remote
I/O parameters for the terminal. This screen is only available for initial setup. Once an application is downloaded, the Remote I/O setup screen is erased.
The table on the next page defines the Remote I/O Parameters.
PV550 Terminal
0
PanelView 900 Keypad Terminal
Publication 2711-6.1
2-10
Initial Setup
Press this function key on:
550/600
↵
900/1000/1400
F1
To set this RIO Parameter Description
Rack #
F1
F2
F3
F4
F5
F6
F2
F3
F4
F5
F6
Rack Size
Starting Module Group
Pass-Through Enabled
Last Chassis
Block Transfer Timeout
Baud Rate
Options
Rack address of terminal on RIO network.
On PV550/600: Press
↵ to open the scratchpad. Enter the rack address and press
↵ again.
On PV900/PV1000/PV1400: Press
F1 to set the rack #, then use the up and down arrow keys to select an address.
Rack size of terminal. Each key press displays a different size. The terminal occupies a single rack.
Starting module group number of the terminal in the assigned rack. Each key press displays a different module group.
Enables or Disables Pass-Through, which lets you transfer applications between a computer on a DH+ link and a terminal on a Remote I/O link.
A PLC-5 controller passes data between the networks.
Specifies whether the terminal occupies the last module group in the assigned rack (applies only to PLC2 controllers).
Timeout value for block transfers.
Each key press toggles a value.
Baud rate at which the terminal will communicate on the RIO network.
0 to 76
1/4, 1/2, 3/4, Full
0,1 2,3 4,5 6,7
Yes or No
Yes or No
0 to 60 seconds
(0 is the default)
Baud Max. Cable
Length
57.6K
10,000 ft
115.2K 5,000 ft
230.4K 2,500ft
Publication 2711-6.1
Chapter Objectives
Application Settings
Chapter
3
Configuring the Terminal
This chapter shows how to use the Configuration Mode menu to configure terminal settings and perform operations including how to:
• access the Configuration Mode menu
• select a language
• use a memory card
• configure communications (DH485, DH+, Remote I/O,
ControlNet, DeviceNet, DF1)
• configure presets
• view terminal information
• set the time and date
• adjust display parameters
• set up the printer
Configuration parameters are set from the terminal or from the
PanelBuilder32 software when creating the application. Settings downloaded with the application have priority over terminal settings if the following option is enabled in the Terminal Setup dialog of the
PanelBuilder32 software.
x Use Downloaded configuration settings
In addition, the application may allow the controller to change the following while the application is running:
• time and date
• current display screen
• piloted control lists
Publication 2711-6.1
3-2
Configuring the Terminal
Accessing the
Configuration Mode Menu
The Configuration Mode menu appears on powerup if an application is not loaded or if the menu was last displayed prior to a reset or power down.
To access Configuration Mode on keypad terminals:
If an application is running, simultaneously press the Left and
Right arrow keys on the terminal keypad.
To access Configuration Mode on touch screen terminals:
• press the Goto Config. Screen button on an application screen or
• press the filled box in the lower right corner of the screen during powerup.
Note: Most of the screens in this chapter are for the PanelView 900 keypad terminal. The screens for other terminals are similar. On keypad terminals you press terminal function keys to modify settings these keys may differ between terminals depending on the screen size and function key placement. On touch screen terminals, you press the screen field or button.
Scrolling
List
PV300 Keypad Terminal
Function keys do not appear on touch screen terminals.
Note: On PV550/PV600 terminals, the Reset Video button is F9.
On PanelView 300 terminals, Reset Video is F2 and Run Mode is F1.
Operations List
Select an operation using the Up or Down arrow keys. Press the
Enter
↵
=key (keypad terminals) or press
(touch screen terminals) to enter the selection.
Language [F8]
Displays the language menu.
Run Mode [F2] or [F1]
Runs the loaded application.
Reset Video [F15] or [F9]
Resets the video to default settings. The reset video function is useful if the screen is set to non-viewable settings.
Publication 2711-6.1
Configuring the Terminal
3-3
Comm and Fault LED
The 2 LEDs on the Configuration Mode menu indicate the operating state of the terminal. The operating states vary for each communication protocol.
DH-485/DH+
LED Indicators
Comm
This pattern
Fault
Solid Fill
Blinking
Flashing
No Fill
Blinking
Indicates
Normal operating state
No communications
When power is first applied (momentarily)
Normal operating state
Hardware is functioning but no application file is loaded or the current application is corrupt.
Remote I/O
LED Indicators
Comm
This pattern
Fault
Solid Fill
No Fill
Blinking
Flashing
No Fill
Blinking
Indicates
Normal operating state
No communications
PLC controller is in program mode
When power is first applied (momentarily)
Normal operating state
Hardware is functioning but no application file is loaded or the current application is corrupt.
Publication 2711-6.1
3-4
Configuring the Terminal
Selecting a Language
Press the Language button, [F8] key, from the Configuration Mode menu to display the Language Selection screen. Note: On PV300 terminals, scroll down on the main configuration menu to select a language.
Choisir Français
Deutsches Meün auswãhlen
Scagliere Italiano
Escoger Español
Select English
FIN
EXIT
USCITA
SALIR
EXIT
The terminal supports 5 languages:
• French
• German
• Italian
• Spanish
• English
Language List
Select a language using the up or down arrow keys. All configuration screens and terminal messages will be displayed in the selected language.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
Using a Memory Card
Configuring the Terminal
3-5
Select Memory Card from the Configuration Mode menu to transfer applications between a memory card and the terminal. Chapter 4 describes the transfer procedure.
Valid Card Inserted
APPLICATIONS ON CARD
\*.PVA
############
F1
Memory
Card
Listing
F8
Disconnect
Card
F2 Restore from Card
F3 Save to Card
F4 Erase / Format Card
EXIT
F16
Memory Card Listing [F1]
Displays the file names of applications on the memory card. Only 1 file name is displayed at a time. Press the Memory Card Listing button or [F1] to scroll through the file names. This button does not display the names of font files (*.OTF).
Disconnect Card [F8] or [F5]
Closes all files on the memory card. Press Disconnect before removing the card from the slot to ensure all files are closed. A message appears when you can remove the card from the card slot.
Failure to follow this procedure could damage the card.
Applications on Card
Displays the selected application file stored on the memory card.
Restore From Card [F2]
Transfers the application under Applications on Card to the terminal.
Any application in the terminal is overwritten.
Save to Card [F3]
Saves the current application in the terminal to the memory card.
Erase/Format Card [F4]
Erases and formats a 2711-NM11, -12, -13, -14 memory card. This function deletes all applications on the card. You can’t delete individual files. Don’t perform this operation on a 2711-NM22, -24,
-26 ATA card or the card will be inoperable.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-6
Configuring the Terminal
Configuring Communications
Select Communication Setup from the Configuration Mode menu to display or change the communication settings for your PanelView terminal. The screen that appears depends on the communication protocol of the terminal.
DH-485 Communications
The DH-485 screen lets you modify or display DH-485 settings for either a DH-485 or RS-232 PanelView terminal. Default settings are:
• Max Node Address = 31
• Node Address = 2
• Baud Rate = 19200
!
ATTENTION: Settings downloaded with a DH-485 application take priority over terminal settings and take effect immediately after the download.
Max Node:
Node:
Baud:
DH-485
31
2
19200
F1
F2
F3
Comm
LED
Fault
LED
EXIT
F16
Max Node [F1]
Opens the numeric entry scratchpad. Enter the highest node number on the network (up to 31) and press the Enter
↵
=key. (On touch screen terminals, press the
↵
=key on the scratchpad). A change to the maximum node address takes effect immediately.
Node [F2]
Opens the numeric entry scratchpad. Enter the node address of the terminal (0 - 31) and press the Enter
↵
=key. (On touch screen terminals, press the
↵
=key on the scratchpad). If you enter a value greater than the maximum node address, the value is accepted and the maximum node address is updated. A node address change takes effect immediately.
Baud [F3]
Steps through the baud rates with each key press: 1200, 2400, 9600,
19200. The selected baud rate takes effect immediately.
Publication 2711-6.1
Configuring the Terminal
Comm LED
Pattern Indicates
Solid Fill
Blinking
Normal operating state
No communications established
Fault LED
Pattern
No Fill
Blinking
Indicates
Normal operating state
Hardware is functioning but no application file is loaded or the current application is corrupted.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
3-7
Publication 2711-6.1
3-8
Configuring the Terminal
DH+ Communications
The DH+ screen lets you display or modify communication settings for the DH+ version of the PanelView terminals.
!
ATTENTION: Settings downloaded with a DH+ application take priority over terminal settings and take effect immediately after the download.
Node:
Baud:
DH+
2
57.6 K
F1
F2
Comm
LED
Fault
LED
EXIT
F16
Node [F1]
Opens the numeric entry scratchpad. Enter the node address (0 - 77 octal) of the terminal on the DH+ link and press the Enter
↵
=key. (On touch screen terminals, press the Enter key on the scratchpad). A node change takes effect immediately.
Baud [F2]
Steps through the baud rates with each key press: 57.6K (default),
115.2K, 230.4K. The selected rate takes effect immediately. The maximum cable length is restricted at higher baud rates.
Comm LED
• solid fill - normal operating state
• blinking - no communications established
• no fill - hardware failure
Fault LED
• no fill - normal operating state
• blinking - hardware is functioning but an application is not loaded or the current application is corrupted.
• solid fill - hardware failure
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
Configuring the Terminal
3-9
Remote I/O Communications
The RIO Configuration screen lets you display communication settings for a Remote I/O terminal. Remote I/O settings are configured with the out-of-box application provided with the terminal or from the PanelBuilder32 software.
RIO Configuration
Rack Number:
Rack Size:
Starting Group:
Pass-Through Enabled:
Last Chassis:
Baud:
No PLC Communication
3
Full
0,1
Yes
Yes
115.2K
F3
EXIT
F16
Settings are read only, except for baud rate.
Rack Number (read only)
Displays the current rack number (0 to 76 octal) of the terminal.
Rack Size (read only)
Displays the current rack size (1/4, 1/2, 3/4 or Full) of the terminal.
Starting Group (read only)
Displays the starting module group of the terminal: 0,1 2,3 4,5 6,7
Pass-Through Enabled (read only)
Enables/disables Pass-Through which allows you to transfer applications between a computer on the Allen-Bradley DH+ network and a terminal on the Remote I/O link. A PLC-5 controller passes data between the two networks.
Last Chassis (ready only)
Indicates whether the terminal occupies the last module group in its assigned rack.
Baud [F3]
Steps through the baud rates with each key press: 57.6K (default),
115.2K, 230.4K. The selected rate takes effect immediately. The maximum cable length is restricted at higher baud rates.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-10
Configuring the Terminal
ControlNet Communications
The ControlNet screen lets you display communications settings for a
ControlNet terminal. You are only allowed to change the Node
Address and Interscan Delay settings.
!
ATTENTION: Settings downloaded with a
ControlNet application take priority over terminal settings and take effect immediately after the download.
ControlNet
New Node Address F2:
##
Active Node Address:
03
Interscan Delay F3:
100 ms
Restart
Terminal
F1
FW Revision: ########
Channel
Status
Comms
Status
Channel B
Connected
Serial #: ########
F16
New Node Address [F2]
Opens the numeric entry scratchpad. Enter the node address (01 - 99 decimal) of the terminal and press the Enter
↵
=key. On touch screen terminals, press the
↵ key on the scratchpad. The initial default is 3.
The change takes effect after the terminal is reset. If you enter a value greater than the UMAX node address, the terminal will not go online with the network.
Active Node Address (read only)
Displays the current address of the PanelView terminal.
Interscan Delay [F3]
Opens the numeric entry scratchpad so you can change the Interscan
Delay. Enter the delay (100 to 1000 milliseconds in multiples of 100) and press the Enter key. On touch screen terminals, press the
↵ key on the scratchpad. The initial default is 100. A change takes effect immediately.
FW Revision (read only)
Shows the revision # of the firmware in the ControlNet terminal.
Serial Number (read only)
Displays a unique, 32-bit serial number for the PanelView terminal.
Comms Status
Displays the current status of the communication card. Connected appears when the PanelView is connected to the network and operating properly.
Publication 2711-6.1
Configuring the Terminal
3-11
Channel Status
Displays a value indicating the current status of channel A and B. The definition of each status condition follows the table. If multiple status conditions apply, the highest priority condition is displayed.
Displayed
Value
119
118
117
116
115
102
101
100
99
114
113
112
103
98
97
96
4
3
6
5
0
7
2
1
2
1
0
4
3
6
5
Status
A B
7 7
7
7
7
7
6
6
6
6
6
6
6
7
6
7
7
70
69
68
67
82
81
80
71
Displayed
Value
87
86
85
84
83
66
65
64
4
3
6
5
0
7
2
1
2
1
0
4
3
6
5
A
Status
B
7 5
5
5
5
5
4
4
4
4
4
4
4
5
4
5
5
38
37
36
35
50
49
48
39
Displayed
Value
55
54
53
52
51
34
33
32
4
3
6
5
0
7
2
1
2
1
0
4
3
6
5
Status
A B
7 3
3
3
3
3
2
2
2
2
2
2
2
3
2
3
3
4
3
6
5
18
17
16
7
Displayed
Value
23
22
21
20
19
2
1
0
4
3
6
5
0
7
2
1
2
1
0
4
3
6
5
A
Status
B
7 1
1
1
1
1
0
0
0
0
0
0
0
1
0
1
1
Status
7
6
5
4
3
2
1
0
Indicates
Terminal failure. Contact Allen-Bradley for technical support.
Self test being performed. Wait for end of test.
Incorrect node configuration. Check for duplicate nodes.
Incorrect network configuration (such as overflow/ underflow if signaled by host, out-of-step). Check for a node greater than UMAX.
Cable fault or lonely connection (such as disconnected cable, redundancy warning).
Temporary network errors (such as bad MAC frame, screeners not programmed).
Channel ok.
Channel disabled.
2
3
Priority
1 (Highest)
4
5
6
7
8 (Lowest)
Restart Terminal [F1]
Resets the PanelView terminal. A new node address takes affect after a reset.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-12
Configuring the Terminal
DeviceNet Communications
The DeviceNet screen lets you display or modify communication settings for a DeviceNet terminal.
!
ATTENTION: Settings downloaded with a
DeviceNet application take priority over terminal settings and take effect immediately after the download.
DeviceNet
New Node Address F2:
Active Node Address:
New Baud F3:
Active Baud:
2
125K
125K
Restart
Terminal
F1
Mod/Net LED:
Not Connected
Input Size:
Output Size:
Bus-off Interrupt F4:
Interscan Delay F5:
Comms Firmware Revision:
Hold in Reset
500 ms
Serial Number:
0
0
EXIT
F16
Restart Terminal [F1]
Resets the terminal.
New Node Address [F2]
Opens the numeric entry scratchpad. Type the node address (0 - 63) of the PanelView on the DeviceNet link or enter 64 to use the address stored on the communications card (Program Mode “PGM” displayed). Press the Enter
↵
=key to store the address. On touch screen terminals, press the
↵
=key on the scratchpad. A node change takes effect on reset. If 64 is entered, the node address can be set from the network using a DeviceNet network configuration tool.
Active Node Address (read only)
Displays the current network operating address of the PanelView terminal. The default is 63.
New Baud [F3]
Step through the baud rates with each key press: 125K (default),
250K, 500K, AutoBaud, PGM. If you select AutoBaud, the terminal determines the baud rate on startup (provided there is sufficient network traffic). If you select PGM, the terminal uses the most recent baud rate stored on the communications card. The selected baud rate takes effect on reset. The maximum cable length is restricted at higher baud rates.
Publication 2711-6.1
Configuring the Terminal
3-13
Active Baud (read only)
Displays the current baud rate of the PanelView terminal. The new baud is displayed after a reset. If the baud rate was set to AutoBaud, active baud displays the rate set by the terminal. If the baud rate was set to PGM, the active baud displays the most recent baud stored on the communications card.
Bus-off Interrupt [F4]
Specifies what occurs when a CAN bus-off interrupt occurs on the
DeviceNet network. The PanelView is not allowed network access when Hold on Reset is selected and a Bus-off Interrupt occurs.
• Hold in Reset holds the PanelView and waits for a communications reset or a terminal reset.
• Reset and Continue Communications resets DeviceNet communications and re-establishes the communications link.
Interscan Delay [F5]
Opens the numeric entry scratchpad so you can change the delay between scans of the Explicit-Client tags. Enter a value of 0 to 65535 milliseconds and press the Enter
↵
=key. (On touch screen terminals, press the
↵ key on the scratchpad.) The default is 500 milliseconds.
This time delay is inserted between each full scan of the Explicit-
Client tags in the current screen context. The value is initially set by the downloaded application but can be changed by an operator. The new value takes effect at the end of the current scan delay.
Explicit-Client mode will generate low priority, network messaging at intervals less than 500 milliseconds.
Input Size
Displays the number of words (0 to 64) sent by the PanelView in an
I/O message. The default value is 0, which indicates that no input data is exchanged with the scanner. This value is set by the downloaded application.
Output Size
Displays the number of words (0 to 64) received by the PanelView in an I/O message. The default value is 0, which indicates no output data is exchanged with the scanner. This value is set by the downloaded application.
Comm LED
• solid fill - normal operating state
• blinking - no communications established
• no fill - hardware failure
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-14
Configuring the Terminal
DF1 Communications
The DF1 screen lets you display or modify DF1/full duplex communication settings for a DF1 PanelView terminal.
!
ATTENTION: Settings downloaded with a DF1 application have priority over terminal settings and take effect immediately after the download.
F1
Communication
Parameters
No Parity
8 Data Bits
1 Stop Bit
DF1 - Full Duplex
F2
Baud Rate
9600
F4
Node
64
F3
Error
Detection
CRC
F5
Handshaking
OFF
Comm
LED
Fault
LED
Connected
EXIT
F16
Communication Parameters [F1]
Sets the communication parameters for the DF1 port on the
PanelView terminal. The settings must match the target device. Each key press toggles through the available combinations for:
• Parity = None (default), Even or Odd
• Data Bits = 8
• Stop Bits = 1 (default) or 2
The DF1 port on the PLC-5 controllers allows a parity of Even or
None parity with 8 Data Bits. For the SLC controllers, the parity is fixed at None and uses CRC error detection.
Baud Rate [F2]
Steps through the baud rates for the DF1 communications port with each key press: 1200, 2400, 4800, 9600, 19200. The initial default is
9600.The baud rate must match the baud rate of the target device.
Error Detection [F3]
Specifies the type of error checking performed on data. The default is
CRC (Cyclic Redundancy Check).
• BCC (Block Check Character) - modulo-256 arithmetic sum of an array of data bytes used for medium-level data verification.
• CRC (Cyclic Redundancy Code) - calculated on an array of data bytes and used for high-level data verification.
Publication 2711-6.1
Configuring the Terminal
3-15
Node [F4]
Specifies the node number (0 - 254 decimal) for DF1 network communications. For point-to-point communications with an SLC,
PLC, MicroLogix or a 1761-NET DNI module, the default node number of 64 is used.
When you press F4, the numeric entry scratchpad opens. Enter a node number and press the Enter
↵
=key. (On touch screen terminals, press the
↵ key on the scratchpad.)
Handshaking [F5]
Specifies the type of handshaking used by the RS-232 port.
• On (CTS/RTS enabled)
• OFF (CTS/RTS disabled)
Press F5 or touch the box to select an option. The default is Off.
Comm LED
• solid fill - normal operating state
• blinking - no communications established with logic controller
• no fill - hardware failure
Fault LED
• no fill - normal operating state
• blinking - hardware is functioning but an application is not loaded or the current application is corrupted.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-16
Configuring the Terminal
Configuring Presets
Select Preset Operations from the Configuration Mode menu to set the values of control objects after a reset or power cycle. You can set presets to:
• values provided by the PanelView application or
• last values entered from terminal prior to a reset or power down.
PRESET OPERATIONS
Power Up With:
Presets
Last States
Key Repeat
Rate
F7
1000 ms
F1
Restart Unit
And
Load Values
F15
Key Repeat
Delay
200 ms
EXIT
F16
Power-Up with Presets or Last States
Displays the current power-up selection. Use the up
% and down
& arrow keys on keypad terminals (or the up and down keys on touch screen terminals) to select an option. The selection takes effect the next time the terminal is powered on.
• Select Presets to load initial values of control objects (into PLC/
SLC data tables) with values supplied by application.
• Select Last States to load initial values of control objects (into
PLC/SLC data tables) with values entered at the terminal prior to a terminal reset or power down.
Restart Unit and Load Values [F1]
Loads the values selected in the Power-Up With list and resets the terminal.
Key Repeat Rate [F4] or [F7]
Specifies the number of repeats that occur per second when a key is pressed and held. Steps through key repeat rates: 0 (disabled), 200ms
(5 times/sec), 250ms (4 times/sec), 330ms (3 times/sec), 500ms (2 times/sec), 1000ms (1 time/sec).
Key Repeat Delay [F9] or [F15]
Specifies how long a key must be pressed before it is repeated. Steps through delay rates: 200ms, 400ms, 600ms, 800ms, 1000ms, 1500ms,
2000ms, 2500ms.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
Viewing Terminal Information
Configuring the Terminal
3-17
Select Terminal Info from the Configuration Mode menu to display information about your terminal. This information may be needed when calling for technical support.
TERMINAL INFO
Boot: ############
Firmware:
############
Hardware:
#######################################
Filename:
Fontfile:
############
############
Bytes Used
Bytes Free
############
############
EXIT
F16
Boot
Displays the boot code revision.
Firmware
Displays the firmware revision.
Hardware
Displays the hardware configuration.
Keypad (CPS)
Touch Screen (TS)
Keypad and Touch Screen (TS CPS)
Communications Port (P0.485,P0.232,P1.RIO,P1.DH+,P1.232,P1.DF1)
Screen Size (SS5.5, SS6.0, SS9.0, SS10.0, SS14.0)
Filename
Displays the name of the active application file. If the application file exists but is invalid, the file name appears as ********.
• Bytes Used displays the number of bytes used by the loaded application.
• Bytes Free displays the number of bytes available.
Font File
Displays the name of the external font file used by the application.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-18
Configuring the Terminal
Adjusting Screen Parameters
Select Screen Setup from the Configuration Mode menu to adjust settings of the terminal display. Changes take effect immediately.
PanelView 550 Screen Setup (PanelView 300 Similar)
F2
Backlight
Off
SCREEN SETUP
F3
Contrast
10
F4
Video Mode
Reverse
F7
Backlight
Timeout
10 min.
F9
Reset
Video
EXIT
F10
Note: Certain settings may make viewing the screen difficult. Do not exit this screen until viewing adjustments are acceptable.
Backlight [F2]
Turns the backlight On, Off or to Timed mode. When set to Timed, the Backlight Timeout value determines when the backlight is turned off. Backlight settings are not available on PanelView 300 terminals.
Contrast [F3]
Increases or decreases the display contrast. The contrast settings range from 0 to 10.
Video Mode [F4]
Toggles between normal video (dark text/graphics on a light background) and reverse video (light text/graphics on a dark background). Changes take effect immediately.
Backlight Timeout [F7]
Specifies when the backlight turns off if user input or a controller screen change is not received. The timeout settings are 5, 10, 20, 25, or 30 minutes. The Backlight Timeout value is used when the
Backlight parameter is set to Timed. Backlight timeout is not available on PanelView 300 terminals.
Reset Video [F9]
Resets the display to normal (default settings). The [F9] key is also active on the Configuration Mode menu. If the screen is set to a nonviewable setting, press the Left and Right arrow keys simultaneously. Then press [F9] to reset the screen.
Screen Saver Mode [F1] and Timeout [F2] ( PanelView 300 only)
Mode - Select Timed or Off screen saver. When Timed, the screen intensity is reduced if user input or a controller screen change is not received within the time specified in the Screen Saver Timeout
Timeout - Specifies when an inactive screen enters screen saver mode. The timeout is adjusted in steps with each key press: 5, 10, 15,
20, 25, or 30 minutes.
Exit [F10]
Returns to the Configuration Mode menu.
Publication 2711-6.1
Screen
Saver
Off
SCREEN SETUP
Normal
Intensity
100
F1 F2
SCREEN SAVER
Timeout
Intensity
10 min.
F9
0
F10
PV600/900/1000 color
Configuring the Terminal
3-19
PanelView 600/900/1000 Color - Screen Setup
Reset
Video
F15
EXIT
F16
SCREEN SETUP
SCREEN SAVER
Timed
F1
Timeout
10 min.
F9
Intensity
0
F10
Contrast
14
F2
Reset
Video
F15
color palette adjusts with contrast
PV600 color touch-screen only
EXIT
F16
Note: Certain settings may make viewing the screen difficult. Do not exit this screen until viewing adjustments are acceptable.
Normal Intensity [F2]
Adjusts the intensity of the display with each key press. PV600/1000 settings are 10 - 100, in 10 step increments. PV900 settings are 50 -
100, in 10 step increments.
Contrast [F2] (PV600 touch-screen only)
Adjusts the contrast of the display with each key press. Valid settings are 1 - 32. The initial default is 14.
Screen Saver Mode [F1]
Sets the screen saver to Timed or Off. When Timed, the screen intensity is reduced if user input or a controller screen change is not received within the time specified in the Screen Saver Timeout box.
Screen Saver Timeout [F6] or [F9]
Specifies when an inactive screen enters screen saver mode. The timeout is adjusted in steps with each key press: 5, 10, 15, 20, 25, or
30 minutes.
Screen Saver Intensity [F7] or [F10]
Adjusts the intensity of the display during screen saver mode. PV600/
1000 settings are 0 - 100, in 10 step increments. PV600 touch-screen only settings are 0 or 100. PV900 settings are 0, and 50 - 100, in 10 step increments. It is recommended that you set the intensity to a value less than 100 to prolong the life of the backlight.
Reset Video [F9] or [F15]
Resets the display to normal video (default settings). The [F9] and
[F15] keys are active on the Configuration Mode menu. If the screen is non-viewable, press the left and right arrow keys simultaneously. Then press [F9] or [F15] to reset the screen.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-20
Configuring the Terminal
PanelView 900 Monochrome - Screen Setup
Normal Intensity
80
F1
Video Mode
Normal
F2
Reset
Video
F15
SCREEN SETUP
SCREEN SAVER
Mode
Timed
F3
Timeout
10 min.
F4
Intensity
80
F5
SCREEN CONDITIONER
Mode
Disabled
F6
Hour
##
:
F7
Minute
0#
F8
EXIT
F16
Note: Certain settings may make viewing the screen difficult. Do not exit this screen until viewing adjustments are acceptable.
Normal Intensity [F1]
Adjusts the intensity of the display with each key press: 35, 40, 50,
60, 70, 80, 90, 100. A new setting takes effect immediately.
Video Mode [F2]
Toggles between normal video (light text/graphics on a dark background) and reverse video (dark text/graphics on a light background). The change takes effect immediately. Normal video is recommended.
Screen Saver Mode [F3]
Sets the screen saver to Timed or Off. When Timed, the screen intensity is reduced if user input or a controller screen change is not received within the time specified in the Screen Saver Timeout box.
Screen Saver Timeout [F4]
Specifies when an inactive screen enters screen saver mode. The timeout is adjusted in steps with each key press: 5, 10, 15, 20, 25 or
30 minutes.
Screen Saver Intensity [F5]
Adjusts the intensity of the display during screen saver mode. The intensity is adjusted with each key press: 0, 35, 40, 50, 60, 70, 80, 90,
100.
Publication 2711-6.1
Configuring the Terminal
3-21
Screen Conditioner Mode [F6]
Enables or disables the screen conditioner. This parameter sets a daily schedule for conditioning the display of a PV900 monochrome terminal to prevent image burn-in.
The conditioning process takes approximately 30 minutes and will not start until the terminal is inactive and in screen saver mode. You can interrupt the screen saver or conditioner at any time by pressing a key or the touch screen. If the screen conditioner is interrupted, it will resume when the screen saver is reactivated.
If you do not use the conditioner, random pixels will illuminate around objects after a period of time (approximately one year).
Screen Conditioner Hour [F7]
Specifies the hour at which to start the screen conditioner. The numeric entry scratchpad opens. Enter a value between 0 - 23, then press the Enter
↵
=key (on touch screen terminals, press the Enter key on the scratchpad).
Screen Conditioner Minute [F8]
Specifies the minute at which to start the screen conditioner. The numeric entry scratchpad opens. Enter a value between 0-59, then press the Enter
↵
=key (on touch screen terminals, press the Enter key on the scratchpad).
Reset Video [F15]
Resets the display to normal video (default settings).
On keypad terminals, the [F15] key is also active on the
Configuration Mode menu. If the screen is non-viewable, press the
Left and Right arrow keys simultaneously. Then press [F15] to reset the screen.
Exit [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-22
Configuring the Terminal
PanelView 1000 Grayscale -Screen Setup
Screen
Saver
Off
SCREEN SETUP
Video
Mode
Normal
F1
F2
SCREEN SAVER
Timeout Intensity
10 min.
0
F9 F10
Reset
Video
F15
EXIT
F16
Note: Certain settings may make viewing the screen difficult. Do not exit this screen until viewing adjustments are acceptable.
Video Mode [F2]
Toggles between normal video (darker text/graphics on a light background) and reverse video (lighter text/graphics on a dark background). The change takes effect immediately. Normal video is recommended.
Screen Saver Mode [F1]
Sets the screen saver to Timed or Off. When Timed, the screen intensity is reduced if user input or a controller screen change is not received within the time specified in the Screen Saver Timeout box.
Screen Saver Timeout [F9]
Specifies when an inactive screen enters screen saver mode. The timeout is adjusted in 5 minute increments with each key press, from
5 to 30 minutes.
Screen Saver Intensity [F10]
Adjusts the intensity of the display during screen saver mode.
Settings are 0 (lowest intensity) or 100 (highest intensity). 0 is recommended to prolong the display life.
Reset Video [F15]
Resets the display to normal video (default settings).
On keypad terminals, the [F15] key is also active on the
Configuration Mode menu. If the screen is non-viewable, press the
Left and Right arrow keys simultaneously. Then press [F15] to reset the screen.
Exit [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
Configuring the Terminal
PanelView 1400 Color Setup
SCREEN
SAVER
Mode
Off
F1
Timeout
5 min.
F2
Intensity
100
F3
SCREEN SETUP
DEGAUSS
Auto
Enabled
F4
Hour Minute
##
:
0#
F5 F6
Normal
Intensity
100
F8
Reset
Video
F15
Manual
Degauss
F7
ALIGN
TOUCH
GRID
EXIT
F16
Touch Screen only
3-23
Note: Certain settings may make viewing the screen difficult. Do not exit this screen until viewing adjustments are acceptable.
Screen Saver Mode [F1]
Sets the screen saver to Timed or Off. When Timed, the screen intensity is reduced if user input or a controller screen change is not received within the time specified in the Screen Saver Timeout box.
Screen Saver Timeout [F2]
Specifies when an inactive screen enters screen saver mode. The timeout is adjusted in 5 minute increments with each key press, from
5 to 30 minutes.
Screen Saver Intensity [F3]
Adjusts the intensity of the display during screen saver mode. The intensity is adjusted with each key press: 0, 25, 50, 75, 100.
Degauss Auto [F4]
Enables or disables automatic degaussing. The degauss process takes a few seconds and will not start until the terminal is inactive.
Automatic degaussing occurs at midnight unless you adjust the hour and time parameters.
Degauss Hour [F5]
Specifies the hour to start automatic degaussing. The numeric entry scratchpad opens. Enter a value between 0 - 23, then press the Enter
↵
= key (on touch screen terminals, press the Enter key on the scratchpad).
Degauss Minute [F6]
Specifies the minute to start automatic degaussing. The numeric entry scratchpad opens. Enter a value between 0 - 59, then press the Enter
↵
= key (on touch screen terminals, press the Enter key on the scratchpad).
Manual Degauss [F7]
Allows you to manually degauss the display. When you press [F7], the display is degaussed immediately.
Publication 2711-6.1
3-24
Configuring the Terminal
Normal Intensity [F8]
Adjusts the intensity of the display with each key press: 25, 50, 75,
100. The new setting takes effect immediately.
Reset Video [F15]
Resets the display to normal video (default settings).
On keypad terminals, the [F15] key is also active on the
Configuration Mode menu. If the screen is non-viewable, press the
Left and Right arrow keys simultaneously. Then press [F15] to reset the screen.
Align Touch Grid - PV1400 Touch Screen only
Opens the touch alignment screen, which lets you realign the screen with the touch grid. This function is useful when the terminal is positioned at an angle and viewing the screen is difficult unless you realign the screen.
EXIT
F16
Move the screen until it aligns with the touch cells. Alignment changes are permanent.
Press:
Exit
To:
Move the screen up one pixel.
Move the screen down one pixel.
Move the screen to the right 2 pixels.
Move the screen to the left 2 pixels.
Move the screen to its factory default position.
Exit the touch alignment screen and return to Screen Setup.
Exit [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
Setting the Time and Date
Configuring the Terminal
3-25
Select Date/Time from the Configuration Mode menu to reset the data and/or time.
Year
####
DATE/TIME
Month
####
Day
####
F1
Hour
####
F9
M MM/DD/YYYY
F2
Minute
####
F3
Second
####
F10
F11
M HH:MM:SS PM
EXIT
F16
Setting the Time
Use screen buttons (touch screens) or function keys to set the time.
On PV550/PV600 Press:
Hours button [F6] key
Minute button [F7]
Second button [F8]
On PV900/1000/1400 Press:
Hour button [F9] key
Minute button [F10]
Second button [F11]
To:
Set current hour
Set minutes
Set seconds
The scratchpad opens to enter each setting. Use the terminal keypad to enter the values. Press
↵
=after each entry. Changes take effect immediately.
Setting the Date
Use screen buttons (touch screens) or function keys to set the date.
Press:
Year button [F1] key
Month button [F2]
Day button [F3]
To:
Set current year
Set month (1 to 12)
Set day (1 to 31)
The scratchpad opens to enter each setting. Use the terminal keypad to enter the values. Press
↵
=after each entry. Changes take effect immediately.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-26
Configuring the Terminal
Setting up the Printer
Select Printer Setup from the Configuration Mode menu to set parameters for those terminals equipped with an RS-232 printer port.
Any printer that supports the IBM enhanced character set can be connected to the RS-232 printer port.
Handshaking
XON/XOFF
F1
Top Of
Form
F9
PRINTER SETUP
Communication Parameters
No Parity
8 Data Bits
1 Stop Bit
F2
Port Mode
Printing
Enabled
F10
Baud Rate
19200
F3
EXIT
F16
Printer settings are maintained between power cycles.
Page format parameters for printing are defined in the Terminal Setup dialog and downloaded with the application.
Handshaking [F1]
Specifies the type of handshaking used by the RS-232 port.
• None (initial default)
• Hardware
• XON/XOFF
If you change the type of handshaking used, you must reset your
PanelView before the change takes effect.
Communication Parameters [F2]
Sets the communication parameters for the printer port. Each key press toggles through the available combinations for:
• Parity (None, Even or Odd)
• Data Bits (7 or 8)
• Stop Bits (1 or 2)
Baud Rate [F3]
Sets the baud rate of the printer port. The baud rate must match the baud rate of the printer. The baud rate is adjusted with each key press:
1200, 2400, 4800, 9600, 19200. The initial default is 9600.
Publication 2711-6.1
Configuring the Terminal
3-27
Top of Form [F6] or [F9]
Notifies the PanelView terminal the printer is at the top of a page.
Manually adjust the printer to the top of the page before pressing the
Top of Form button. The printer also uses the Perforation Skip Value
(if defined in the Printer Setup of the PanelBuilder32 software) when the Top of Form button is pressed.
On powerup, the terminal assumes the printer is at the top of a page.
We recommend that you also set the PanelView terminal to the top of the page so that the printer and PanelView are at the same starting point. Otherwise your printout may not start at the top of the page.
Port Mode [F7] or [F10]
Enables or disables printing for the RS-232 port.
The RS-232 port on some terminals supports both printing and application transfers. If you disable printing, the port is used for application transfers.
Exit [F10] or [F16]
Returns to the Configuration Mode menu.
Publication 2711-6.1
3-28
Configuring the Terminal
Publication 2711-6.1
Chapter Objectives
Supported Memory Cards
Chapter
4
Using a Memory Card
This chapter describes:
• supported memory cards
• using the memory card retainer
• loading application from a memory card
• loading application on a memory card
• storing font files on a memory card
• removing a memory card
Memory cards are available to transfer application files to/from a
PanelView terminal.
PanelView terminals running firmware 3.0 (or later) and computers with an ATA card drive support the following cards.
• 4M flash ATA card (Catalog No. 2711-NM24)
• 8M flash ATA card (Catalog No. 2711-NM28)
• 16M flash ATA card (Catalog No. 2711-NM216)
All PanelView terminals and computers with a DataBook TMB240 or
TMB250 card drive support these cards:
• 256K flash memory card (Catalog No. 2711-NM11)
• 1M flash memory card (Catalog No. 2711-NM12)
• 2M flash memory card (Catalog No. 2711-NM13)
• 4M flash memory card (Catalog No. 2711-NM14)
Publication 2711-6.1
4-2
Using a Memory Card
Using the Memory Card Retainer
A Memory Card Retainer (Catalog No. 2711-NMCC, -NMCD,
-NMCE) is shipped with all PanelView terminals, except the PV1400.
It is required for:
• UL508 installations
• vibration/mechanical shock environments
• CE certified installations
• installations where the application uses a font file on a memory card, and the card must remain in the terminal during operation.
The following illustration shows the memory card and the memory card retainer. The card loads in the back of the terminal with the key slot on top.
Key Slot
Memory Card Retainer
Connector Slots
A-B logo on right side
Memory Card Slot
Note: The back of the PanelView 900 terminal is shown above. The location of the card slot will vary between the different terminals.
Publication 2711-6.1
Using a Memory Card
The Memory Card Retainer protects against:
• electrical shock from loose high voltage wires in an electrical enclosure per UL508
!
ATTENTION: When permanently installing a memory card in an electrical enclosure, the memory card retainer must be used to avoid accidental contact of high voltage leads to metal surfaces on the card.
Failure to use the retainer could result in physical injury or damage to the terminal.
4-3
• electrostatic discharge (ESD) up to 15KV
!
ATTENTION: Without the memory card retainer installed, electrostatic discharge could reset or damage the PanelView terminal.
• accidental removal or ejection of the memory card from the card slot.
!
ATTENTION: Accidental removal of an ATA flash card from the card slot could result in damage to the card.
Publication 2711-6.1
4-4
Using a Memory Card
Loading Application from a Memory Card
The procedure below shows how to load an application on a memory card into the PanelView terminal.
!
ATTENTION: Explosion Hazard - Do not install or remove memory card unless power has been switched off or the area is known to be non-hazardous.
To load an application from a memory card:
1. Insert the memory card in the card slot of the terminal.
If the terminal does not have an application loaded, the
Configuration Mode menu appears. Skip step 2.
2. Open the Configuration Mode menu by simultaneously pressing the Left and Right arrows (on keypad terminals), or the Goto
Config. Screen button (on touch screen terminals).
Function keys do not appear on touch screen terminals.
3. Select Memory Card and press the Enter
↵
=key.
4. Press Memory Card Listing, [F1] on keypad terminals, until the application file you want to load is displayed.
Publication 2711-6.1
Using a Memory Card
4-5
5. Press Restore From Card, [F2] on keypad terminals, to begin the transfer.
Because this operation overwrites the current application in the terminal, you are prompted to abort or continue.
Proceed with download?
F1 - Abort
F2 - Continue
The terminal displays the status of the transfer.
In progress . . .
6. When the transfer is complete, the PanelView terminal checks the validity of the application, resets and runs the application.
Publication 2711-6.1
4-6
Using a Memory Card
Loading Application on a Memory Card
The steps below show how to load an application in the terminal onto a memory card.
!
ATTENTION: Explosion Hazard - Do not install or remove memory card unless power has been switched off or the area is known to be non-hazardous.
To transfer an application to a memory card:
1. Insert the memory card into the card slot of the terminal.
2. Open the Configuration Mode menu by simultaneously pressing the Left and Right arrows (on keypad terminals), or the Goto
Config. Screen button (on touch screen terminals).
Function keys do not appear on touch screen terminals.
3. Select Memory Card and press the Enter
↵
=key.
4. If necessary, press Erase/Format Card, [F4] key on keypad terminals, to format or erase a 2711-NM11, -12, -13, -14 memory card.
Do not perform this operation on a 2711-NM2xx ATA card
(where xx is size in megabytes). The card becomes inoperable.
Because this operation erases all data on the memory card, you are prompted to abort or continue.
Format erases entire card?
F1 - Abort
F2 - Continue
Publication 2711-6.1
Using a Memory Card
5. Press Save to Card, [F3] on keypad terminals, to transfer the application in the terminal to the card.
If the application already exists on the memory card, you are prompted to abort or continue.
The .PVA file exits:
F1 - Abort
F2 - Upload with new PVA file
The terminal displays the status of the transfer.
4-7
In progress . . .
6. When the transfer is complete, the application file name appears in the Applications on Card list. Press Memory Card Listing, [F1] key on keypad terminals, to scroll through the list.
Note: If you upload a file that exists on the memory card, the uploaded file name is altered with a sequential digit as a suffix.
For example, Control.pva becomes Control0.pva.
For files with eight character names, a digit overwrites the last character. For example, Motorcon.pva becomes Motorco0.pva.
Publication 2711-6.1
4-8
Using a Memory Card
Storing Font Files on a Memory Card
Removing a Memory Card
Memory cards also store font files for languages used by PanelView applications. The font file contains the character set for the language.
The memory card containing the font file must be inserted in the
PanelView terminal while the application is running. The terminal uses the font file to display characters on the application screen.
To view the name of the font file used by an application, select
Terminal Info from the Configuration Mode menu.
Because the memory card must remain in the terminal while the application is running, it is recommended that you use the Memory
Card Retainer (Cat. No. 2711-NMCC, -NMCD, -NMCE) to secure the card in the card slot. The retainer ensures the card is not accidentally removed or dislodged during terminal operation.
Follow the procedure below to remove a memory card from the
PanelView terminal. Failure to follow this procedure may result in damage to the card.
1. Select Memory Card from the Configuration Mode menu.
2. Press the Disconnect Card button. This ensures that all files are closed on the card.
A message prompts you to remove the card from the slot. You can continue or abort the operation.
3. Press the Continue button.
4. Remove the memory card from the card slot.
On PV1400 terminals, press the Memory Card Eject button.
Publication 2711-6.1
Chapter Objectives
Application Information
Chapter
5
Running Applications
This chapter describes operating procedures common to most applications:
• screen security
• push button operation
• control lists
• numeric entry controls
• ASCII entry controls
• screen selectors
• list indicators
• multistate indicators
• analog gauges
• bar graphs
• numeric data displays
• message displays
• time or date
• printing
• alarms
The application designer is responsible for documenting the operation of an application. Before running the application, you should understand what processes are being controlled and monitored.
!
ATTENTION: Do not press multiple touch screen objects at the same time. Pressing multiple objects simultaneously may result unintended operation.
Publication 2711-6.1
5-2
Running Applications
Screen Security
Push Button Operation
Access to some application screens (including the terminal configuration screens) may be restricted. Secured screens require you to enter a password before the screen is displayed. It is the responsibility of the application designer to provide operators with required passwords.
Other screens may allow an authorized operator to select and change the passwords of operators at the terminal.
Screen push buttons function like mechanical push buttons.
Push Button
ON
OFF
Push buttons have a variety of appearances. Push buttons may change their inner text, fill pattern, border or shape when pressed (each state assigned different attributes).
OFF
Toggle Foreground/
Background
ON
Border, White Fill
SLOW
No Border,
Diagonal Fill
STOP
Ellipse, White Fill
The following are common to most push buttons:
• All push buttons are momentarily disabled (0.5 second) after a screen change. This prevents multiple buttons, in the same location on different screens, from being pressed inadvertently.
• All push buttons must be released on the previous screen before buttons can be pressed on the new screen.
• Momentary push buttons are assigned a hold time. The hold time maintains the pressed state so that each change of state can be read by the controller at least once. The hold time varies between
0 and 1 second depending on the configured setting.
Publication 2711-6.1
Control Lists
Active selection is highlighted
Running Applications
5-3
Control lists perform functions similar to push buttons. They can modify either individual bits or values at a controller address.
Cursor indicates selected item
Vertical bar indicates active control list
Active List Item
Active item is highlighted.
Active Control List
Has a vertical indicator bar on the left side of the list. Only one control list or numeric entry cursor point can be active on a screen.
To activate a control list:
• touch the object (touch screen terminals only)
• or press the assigned function key
• or on a screen with multiple control lists or numeric entry cursor points, press the Left or Right arrows to move the indicator bar between the objects.
Tank Level Control
Empty Tank
1/4 Fill Level
1/2 Fill Level
Full Tank
Hopper Control
Open Hopper 1
Open Hopper 2
Open Hopper 2
Close Hopper 2
Moves the vertical bar
Publication 2711-6.1
5-4
Running Applications
Cursor
Indicates the selected item. Move the cursor up or down the control list using the Up and Down arrow keys. Cursor operation is configured by the application designer. If the cursor is at the first or last item in a control list pressing the Up arrow (when at the top) or the Down arrow (when at the bottom) will either:
• cause no movement of the cursor, or
• move the cursor to the top or bottom of the list.
Tank Level Control
Empty Tank
Tank Level Control
Empty Tank
1/2 Fill Level
Full Tank
1/2 Fill Level
Full Tank
If the list contains more items than can appear at one time, the list scrolls. If the cursor is at the top or bottom of a scrolling list, the list scrolls one row at a time as the arrow keys are pressed.
List Keys
Touch screen terminals require list keys on the screen to move the cursor in a control list and select entries. The following table shows the list keys.
List Key Type
Move Up
Move Down
Home
End
Page Up
Page Down
Backspace
Enter
Description
Moves the cursor to the previous item in the list.
Moves the cursor to the next item in the list.
Moves the cursor to the first item in the list.
Moves the cursor to the last item in the list.
Moves the cursor up one page in a scrolling list.
Moves the cursor down one page in a scrolling list.
Returns the cursor to the currently highlighted selection.
Confirms a selection and sends the value to the controller if Write on Enter was configured for the control list.
Publication 2711-6.1
Running Applications
5-5
Cursor - Piloted Control Lists
On a piloted control list, some items are under controller operation only. In addition, some items may be designated as inactive. You cannot select controller items or inactive items. In both cases, the cursor is hollow when you select the item.
Active State
State 1
State 2
State 3
State 4
State 5
Cursor at state 2, an active state
Inactive State
State 1
State 2
State 3
State 4
State 5
Cursor at inactive state 3,
Cursor changes and highlight remains in original position
Active State
State 1
State 3
State 4
State 5
Cursor at active state 4,
Cursor changes back and highlight moves to selection.
To select an item on a control list:
1. Select the control list by:
• touching the screen object (touch screen terminals only)
• or pressing its function key
• or pressing the Left or Right arrow keys until the control list has a vertical bar indicating it is active
2. Move the cursor up or down the list using the Up or Down arrows. If the cursor is hollow, the item cannot be selected.
3. Depending on the application design, you may or may not have to press
↵
=to enter the selection indicated by the cursor.
Publication 2711-6.1
5-6
Running Applications
Numeric Entry Controls
Two types of controls allow a numeric value at a controller address:
Cursor Point and Keypad Enable button.
Cursor Point
Active
Cursor Point
Press F1 to Enter New Speed
Current Speed = 100 RPM
Motor 1
45
Motor 2
100
34962
Numeric Entry Cursor Point
Cursor points appear as a box. A vertical line on the left side of the box appears when the cursor point is selected. Data is entered in a numeric entry scratchpad.
Enter
Value
367
Keypad Enable Button
A keypad enable button appears like a standard push button. The data displayed in the button is the last value sent to the button’s tag address. When selected, a numeric entry scratchpad opens.
Scratchpad
Both controls display a numeric entry scratchpad in the center of the screen. The scratchpad shows the current value entered and the range of possible values you can enter.
Current value entered in scratchpad
550/600 Touch Screen only
Terminal Scratchpad
Keypad and Keypad/Touch Screen
Terminal Scratchpad
900/1000/1400Touch Screen
Terminal Scratchpad
During data entry, wait until the number you enter appears in the scratchpad before entering the next number.
Publication 2711-6.1
Running Applications
5-7
To enter a cursor point:
1. Select the cursor point by:
• touching the object (touch screen terminal only)
• pressing the associated function key
• press the Left or Right arrows until the cursor point shows a vertical bar
2. Press Enter
↵
=or type the first digit of the number you want to enter.
The scratchpad opens.
3. Enter the value using the terminal keypad and press Enter
↵
.
To enter a value using the keypad enable button:
1. Press the keypad enable button.
The scratchpad opens.
2. Enter the value using the terminal keypad and press Enter
↵
.
To change an entry on a scratchpad:
1. Press the backspace
←
= key to delete one character at a time.
2. Enter a new value and press Enter
↵
.
To cancel a scratchpad:
1. Press the Backspace
←
= key to delete one character at a time.
2. When pressing Backspace
← in an empty scratchpad (value = 0), the scratchpad is removed.
Publication 2711-6.1
5-8
Running Applications
ASCII Entry Controls
Display Area
ASCII entry controls allow you to send an alphanumeric string (up to
128 characters) to a controller. Like numeric entry controls, the
ASCII entry control can appear on a screen as a keypad enable button or a cursor point. When either object is activated, the ASCII scratchpad opens.The look of the scratchpad depends on the terminal.
ASCII Scratchpad - Keypad or Keypad/Touch Screen Terminals
Character Keyboard
←
↵
Controls Location
Terminal Keypad
Terminal Keypad
Terminal Keypad
SEL F1
INS F2
Function Keys
Function Keys
<< F3
>> F4
ESC 5
CTRL F6
Function Keys
Function Keys
Function Keys
Function Keys
Controls
Select characters from the Character Keyboard by moving the cursor
(with the keypad arrows) over a character and pressing the Sel-F1 function key. The character appears in the Display Area. This area scrolls so you can enter a string that is longer than the Display Area.
All characters are sent to the controller even if not visible.
After entering characters, press
↵ to send the string to the controller.
The leftmost character is placed in the high byte of the first word (of the write tag), the next character in the low byte, and so on.
Note: DeviceNet ASCII entry allows for byte swapping.
Function
Moves the cursor up, down, left, or right in the Character Keyboard.
Deletes the character to the left of the cursor in the Display Area. If the cursor is at the leftmost position when you press
←,
= the scratchpad closes.
Sends the character string to the assigned write tag address in the controller.
When opening the ASCII scratchpad, the string is highlighted. If you select a character immediately, the terminal clears the Display Area and displays the selected character. If you press a control key, the terminal continues to display the existing string, allowing you to edit it.
Selects the highlighted character and places it at the cursor position in the Display Area.
Toggles between Insert and Overstrike mode. Overstrike mode appears in reverse video. In
Insert mode, the selected character is inserted before the cursor in the Display Area. If the maximum number of characters is entered in the Display Area, new characters are ignored. In
Overstrike mode, the selected character replaces the character at the cursor in the Display
Area.
Moves the cursor one character to the left in the Display Area.
Moves the cursor one character to the right in the Display Area.
Closes the scratchpad without making any changes.
Clears the string in the Display Area.
Publication 2711-6.1
Cursor
Control Keys
Running Applications
ASCII Scratchpad - 550/600 Touch Screen Terminals
Character Keyboard
Cursor
Display Area
5-9
Controls
<<
>>
ESC
CLR
←
↵
Controls
SEL
INS
To select characters from the Character Keyboard, press the cursor control keys to move the cursor over a character and then press the
SEL key. The character is entered in the Display Area. This area scrolls so you can enter a string that is longer than the Display Area.
All characters are sent to the controller even if not visible.
After entering the characters, press
↵ to send the string to the controller. The leftmost character is placed in the high byte of the first word (of the write tag), the next character in the low byte, and so on.
Note: DeviceNet ASCII entry allows for byte swapping.
Function
Moves the cursor up, down, left, or right in the Character Keyboard.
Selects the highlighted character and places it at the cursor position in the Display Area.
Toggles between Insert and Overstrike mode. Overstrike mode appears in reverse video. In
Insert mode, the selected character is inserted before the cursor in the Display Area. If the maximum number of characters is entered in the Display Area, new characters are ignored. In
Overstrike mode, the selected character replaces the character at the cursor in the Display
Area.
Moves the cursor one character to the left in the Display Area.
Moves the cursor one character to the right in the Display Area.
Closes the scratchpad without making any changes
Clears the string in the Display Area.
Deletes the character to the left of the cursor in the Display Area.
Sends the character string to the assigned write tag address in the controller.
When opening the ASCII scratchpad, the string is highlighted. If you select a character immediately, the terminal clears the Display Area and displays the selected character. If you press a control key, the terminal continues to display the existing string so you can edit it.
Publication 2711-6.1
5-10
Running Applications
Display Area
Character Keyboard
ASCII Scratchpad - 900/1000/1400 Touch Screen Terminals
Controls
<<
>>
ESC
CLR
←
↵
Controls
SHF
(Shift)
CAPS
INS
Select characters by touching the Character Keyboard on the screen.
The character is entered in the Display Area. This area scrolls so you can enter a string that is longer than the Display Area. All characters are sent to the controller even if not visible.
After entering the characters, press
↵
= on the scratchpad to send the characters to the controller. The leftmost character is placed in the high byte of the first word (of the write tag), the next character in the low byte, and so on.
Note: DeviceNet ASCII entry allows for byte swapping.
Function
By default this function is off and keys are in unshifted state. When you press SHF, the button appears in reverse video. All character keys, including numbers and symbols, appear in the shifted state. For example, a becomes A; 2 becomes @.
By default, keys appear in lowercase. When you press CAPS, the button appears in reverse video. Letters appear and are entered in uppercase but numbers and symbols are not shifted.
This state is maintained between power cycles.
Toggles between Insert and Overstrike mode. Overstrike mode appears in reverse video.
In Insert mode, the selected character is inserted before the cursor in the Display Area. If the maximum number of characters is entered in the Display Area, new characters are ignored.
In Overstrike mode, the selected character is replaced at the cursor in the Display Area.
Moves the cursor one character to the left in the Display Area.
Moves the cursor one character to the right in the Display Area.
Closes the scratchpad without making any changes.
Clears the string in the Display Area.
Deletes the character to the left of the cursor in the Display Area.
Sends the character string to the assigned write tag address in the controller.
After pressing
↵
= to open the ASCII scratchpad, the string is highlighted. If you select a character immediately, the terminal clears the Display Area and displays the selected character. If you press a control key, the terminal continues to display the existing string so you can edit it.
Publication 2711-6.1
Running Applications
5-11
ASCII Scratchpads in Other Languages
The ASCII Scratchpad is available with character keyboards in:
• French
• German
• Italian
• Spanish
If the PanelView terminal is configured for operation in one these languages, the ASCII scratchpad will display the appropriate
Character Keyboard.
The SHF control toggles between SHF/SHF2. In SHF mode, the
Character Keyboard displays the shifted state characters (e.g., a to A, and 3 to #). In SHF2 mode, the Character Keyboard displays additional characters available for the language.
Publication 2711-6.1
5-12
Running Applications
Screen Selectors
The 2 types of screen selector controls are Screen List Selectors and
Screen buttons.
Screen List
Selector
Vertical bar indicates active list
Screen Controls
Monitor
Pump Status
Valve Status
Tank Control
Tank
Screen
Previous
Screen
Goto
Screen Button
Return
Screen Button
Goto and Return screen buttons can have a variety of appearances such as unique inner text, fill pattern, border or shape. Return screen buttons display the previous screen. Goto screen buttons display the assigned screen.
Screen lists display a list of application screens. The selected screen is highlighted.
To activate a screen list:
• touch the object (touch screen only)
• or press the assigned function key
• or on a screen with multiple screen lists, press the Left or Right arrow key until a vertical bar appears.
To select an item on a screen list:
1. Move the cursor up or down the list using the Up or Down arrow keys.
2. Press Enter
↵
=to enter the selection.
The selected screen is displayed.
Publication 2711-6.1
Running Applications
5-13
Cursor Operation
Cursor operation is configured by the application designer. If the cursor is at the first or last item in a screen list, pressing the Up
= arrow (when at top) or Down arrow (when at bottom) will either:
• cause no movement of the cursor, or
• move the cursor to the top or bottom of the list
Screen Controls
Monitor
Pump Status
Valve Status
Tank Control
Screen Controls
Monitor
Pump Status
Valve Status
Tank Control
If a screen list contains more items than can appear at one time, the list scrolls. If the cursor is at the top or bottom of a scrolling list, the list scrolls one row at a time as the Up/Down arrows are pressed.
List Keys
Touch screen terminals require list keys on the screen to move the cursor in a screen list and select an entry. The following table shows the list keys.
List Key Type
Move Up
Move Down
Home
End
Page Up
Page Down
Backspace
Enter
Description
Moves the cursor to the previous item in the list.
Moves the cursor to the next item in the list.
Moves the cursor to the first item in the list.
Moves the cursor to the last item in the list.
Moves the cursor up one page in a scrolling list.
Moves the cursor down one page in a scrolling list.
Returns the cursor to the currently highlighted selection.
Confirms a selection and displays the screen.
Publication 2711-6.1
5-14
Running Applications
List Indicators
Multistate Indicators
Bar Graph Displays
Analog Gauges
List indicators highlight an item from a list depending upon the status of either a bit or value at a controller address.
List Indicator
Mixer Speed
Off
Low
Medium
High
Mixer
On
Mixer
Off
Current status is highlighted
An indicator list may have a maximum of 255 entries. The list automatically scrolls to display the status of an item. Note: List indicators do not have a cursor like control or screen selector lists.
Multistate indicators display the status of either a bit or value at a controller address.
Multistate indicators can have a variety of appearances. In addition, multistate indicators may change their inner text, fill pattern, or graphic with each state (each state assigned different attributes). Each indicator may have up to 2,000 states.
Temp
High
Toggle Foreground/
Background
Temp
Low
Border, White Fill
OFF
Cross Hatch,
No Border
Normal
Ellipse, White Fill
Bar graphs provide a graphical representation of a variable value. Bar graphs can appear with or without scales and border, and can have a variety of fill patterns.
100 +200
-10 0 +10
Vertical Bar
Hatched Fill,
No Scale
0
Vertical Bar
Solid Fill, with Scale
-200
3 Vertical Bars
Various Fills, with Scale
2 Horizontal Bars
Different Fill, with Scale
The analog gauge uses a rotating needle to display a process variable such as speed, temperature or pressure. The gauge consists of a circular scale with tick-marks, 1 to 4 needles, and a label with text or variable data. The circular scale is an integral part of the gauge but can be created separately.
80
100
120
60 140
Pressure
40
160
20
0
200
180
Publication 2711-6.1
Numeric Data Displays
Message Displays
Time or Date
Running Applications
5-15
Numeric Data Displays may appear with or without supporting text.
Flow= 37 Gallons
0 0 0 2 3 9 . 4 5
Depending on the application design, displayed data may have these properties:
• zero fill
• fixed, floating or no decimal point
• different field widths (number of digits)
• various text sizes
• scaled
Message displays contain alphanumeric characters and are displayed when triggered by a controller. The message display can be any size and will not overlap other controls. Messages may contain:
• alphanumeric text
• variable data
• graphics
• time and date
Time and date information can appear as a separate item or in some control/display objects (push buttons, multistate indicators, message displays or data displays). A time and date can appear with or without supporting text.
The date can have a variety of formats.
Month/Day/Year
7/3/99
Day/Month/Year
3/7/99
Year/Month/Day
99/7/3
With Leading Zeroes
07/03/99
With 4 Digit Year
3/7/99
With User-Defined Separator
7*3*99
The time can also have a variety of formats.
12 Hour Format
2:56
24 Hour Format
14:56 with Seconds
14:56:29
With Time Zone & Time
Standard Designations
07/03/97
With Leading Zeroes
02:56
With User-Defined Separator
14*56*29
Publication 2711-6.1
5-16
Printing
Running Applications
Alarms
Terminals equipped with an RS-232 printer port can print:
• triggered messages in a message display
• triggered states of a multistate indicator
• alarm messages
• alarm list
Text is printed without formatting options. Print attributes for objects and alarms are defined in the application.
Printing is a background operation. While printing, the terminal continues to update and you can perform other terminal operations.
The terminal prints messages in the order they are received. If the print buffer is full, the terminal displays a queue full warning message. New print requests are aborted.
The print queue is not maintained between power cycles. Any messages in the queue when the terminal is reset are cleared.
Applications that support alarms may contain:
• Alarm Banner display that pops up when an alarm is triggered
• Alarm buttons that enable the operator to act on an alarm (Print
Alarm, Acknowledge Alarm, Clear Alarm, Acknowledge All)
• Alarm List which stores information on triggered alarms (Print
Alarm List or Clear Alarm List button)
Alarm configurations are application dependent. Consult your application designer for details on how to handle alarms for your application.
Publication 2711-6.1
Chapter Objectives
Hazardous Locations
Enclosures
Chapter
6
Installing the PV300 Terminal
This chapter describes how to mount the PV300 terminal in a panel or enclosure including:
• hazardous locations
• enclosures
• required tools
• mounting dimensions
• clearances
• cutout dimensions
• installing the PV300 terminal in a panel
See the nameplate label on terminal for hazardous locations certifications.
!
ATTENTION: In Class 1, Division 2 Hazardous locations, the Plainview 300 terminal must be wired per the National Electric Code as it applies to hazardous locations. Peripheral equipment must also be suitable for the location in which it is installed.
The PV300 terminals have an operating temperature code of T4
(maximum operating temperature of 135
°
C or 275° F). Do not install these terminals in environments where atmospheric gases have ignition temperatures less than 135° C (275° F).
Mount the PV300 terminal in a panel or enclosure to protect the internal circuitry. The terminal meets NEMA Type 12/13 and 4X
(indoor use) ratings only when mounted in a panel or enclosure with the equivalent rating.
Allow enough space within the enclosure for adequate ventilation.
Consider heat produced by other devices in the enclosure. The ambient temperature around the terminals must be between 0° and
55° C (32° and 131° F).
Make provisions to access the back panel of the terminal for wiring, maintenance, installing a memory card and troubleshooting.
Publication 2711-6.1
6-2
Installing the PV300 Terminal
Required Tools
Mounting Dimensions
Other than the tools required to make the PV300 panel cutout, the tools required for installation are:
• 7 am (M4) deep well socket wrench or nut driver
• small slotted screwdriver
• torque wrench (in / labs)
The illustration below shows mounting dimensions for the PV300 keypad terminals
Top View
197 mm
(7.76 in)
69mm
(2.73 in)
82 mm
(3.21 in)
Cutout Dimensions
140 mm
(5.53 in)
Use the full size template shipped with the PV300 terminal to mark the cutout dimensions. Below is a reduce size cutout.
120 am
4.71 in)
109 mm
4.29 in)
R 4.5 am via
(0.178 in)
Recommended Panel
Cutout Dimensions
140 am
5.53 in)
178 am
6.99 in)
Publication 2711-6.1
Clearances
Leave 64 mm (2.5 in) for Mounting and Air Flow
Installing the PV300 Terminal
6-3
When installing the PV300 terminal, allow space for mounting, air flow, maintenance, memory card and legend strip installation.
Side, Top and Bottom Clearances
Terminal Cutout
Use full size template shipped with terminal
Leave 64 am (2.5 in) for Mounting and Air Flow
Back Clearance
69 am
(2.73 in)
Memory Card Retainer
134.6 mm
5.3 in)
Card
215.9 am (8.5 in) is required with card retainer. Allows 6mm (.25) in clearance) to insert and remove a memory card with the memory
Publication 2711-6.1
6-4
Installing the PV300 Terminal
Installing the PV300 in a Panel
To install the PV300 terminal in a panel:
!
ATTENTION: Disconnect all electrical power from the panel before making the cutout.
Make sure the area around the panel cutout is clear.
Do not allow metal cuttings to enter any components that may already be installed in the panel.
Failure to follow this warning may result in personal injury or damage to the panel components.
1. Cut an opening in the panel using the panel cutout provided with the terminal. Remove any sharp edges or burrs.
2. Make sure the terminal sealing gasket is properly positioned on the terminal as shown below. This gasket forms a compression type seal. Do not use sealing compounds.
Sealing Gasket
Legend Strip
3. Verify that the end of the legend strip is fully inserted and does not interfere with the sealing gasket.
4. Place the terminal in the panel cutout.
5. Verify that the opening is the proper size to clear the bezel and to allow the gasket to contact the panel.
Publication 2711-6.1
Installing the PV300 Terminal
6. Install the self-locking nuts hand tight.
Protective installation label
Self-locking nuts
(4 used, 6 provided)
Mounting Studs (2 left, 2 right)
6-5
7. Alternately tighten the self-locking nuts until the terminal is held firmly against the panel. Tighten nuts to a torque of 10 inchpounds. Do not over-tighten.
!
ATTENTION: Mounting nuts must be tightened to a torque of 10 inch-pounds to provide a proper seal and to prevent potential damage to the terminal. Allen-
Bradley assumes no responsibility for water or chemical damage to the terminal or other equipment within the enclosure because of improper installation.
8. Remove the protective installation label covering the top vents of the terminal.
!
ATTENTION: Failure to remove the protective installation label covering the top vents could result in overheating and damage to the terminal.
Publication 2711-6.1
6-6
Installing the PV300 Terminal
Publication 2711-6.1
Chapter Objectives
Hazardous Locations
Chapter
7
Installing the PV550 Terminal
This chapter describes how to mount the PV550 terminal in a panel or enclosure including:
• hazardous locations
• enclosures
• required tools
• mounting dimensions
• clearances
• cutout dimensions
• installing the PV550 terminal in a panel
See the nameplate label on terminal for hazardous locations certifications.
!
ATTENTION: In Class 1, Division 2 Hazardous locations, the PanelView 550 terminal must be wired per the National Electric Code as it applies to hazardous locations. Peripheral equipment must also be suitable for the location in which it is installed.
The following PV550 terminals have an operating temperature code of T2 (maximum operating temperature of 300
°
C or 572° F).
• keypad terminals (series C or higher)
• keypad & touch screen terminals (series C or higher)
• all touch screen only terminals
Do not install these terminals in environments where atmospheric gases have ignition temperatures less than 300° C (572° F).
Publication 2711-6.1
7-2
Enclosures
Installing the PV550 Terminal
Required Tools
Mounting Dimensions
Mount the PV550 terminal in a panel or enclosure to protect the internal circuitry. The terminal meets NEMA Type 12/13 and 4X
(indoor ruse) ratings only when mounted in a panel or enclosure with the equivalent rating.
Allow enough space within the enclosure for adequate ventilation.
Consider heat produced by other devices in the enclosure. The ambient temperature around the terminals must be between 0° and
55° C (32° and 131° F).
Make provisions to access the back panel of the terminal for wiring, maintenance, installing a memory card and troubleshooting.
Other than the tools required to make the PV550 panel cutout, the tools required for installation are:
• 7 mm (M4) deep well socket wrench or nut driver
• small slotted screwdriver
• torque wrench (in / lbs)
The illustration below shows mounting dimensions for the PV550 terminals.
PV550 Keypad, Keypad & Touch Screen Terminals
Top View
167 mm
(6.57 in)
86 mm
(3.39 in)
106 mm
(4.17 in)
266 mm
(10.47 in)
152 mm
(6.00 in)
PV550 Touch Screen Terminals
Top View
64 mm
(2.54 in)
82 mm
(3.20 in)
185 mm
(7.28 in)
Publication 2711-6.1
Clearances
PV550 Touch Screen Terminals
Installing the PV550 Terminal
7-3
When installing the PV550 terminal, allow space for mounting, air flow, maintenance, memory card and legend strip installation.
PV550 Keypad, Keypad & Touch Screen Terminals
Leave 25 mm (1.0 in) for Mounting and Air Flow
Terminal Cutout
Use full size template shipped with terminal
Leave 25 mm (1.0 in) for Mounting and Air Flow
Terminal Cutout
Use full size template shipped with terminal
Leave 38 mm (1.5 in) for Mounting, Air Flow and Wiring Connections
Back Clearance
64 mm
(2.54 in)
Memory Card Retainer
109 mm
(4.3 in)
Card
188 mm (7.40 in) is required to insert and remove a memory card with the memory card retainer.
Back Clearance
86 mm
(3.39 in)
Card
207 mm (8.15 in) is required to insert and remove a memory card with the memory card retainer.
Memory Card Retainer
Publication 2711-6.1
7-4
Installing the PV550 Terminal
Cutout Dimensions
Use the full size template shipped with the PV550 terminal to mark the cutout dimensions. Below is a reduce size cutout.
25.9 mm
(1.02 in)
PV550 Keypad, Keypad & Touch Screen Terminals
106 mm
(4.19 in)
191 mm
(7.51 in)
243 mm
(9.55 in)
3.3 mm
(0.13 in)
85 mm
(3.33 in)
4.8 mm dia
(0.188 in)
3.3 mm
(0.13 in)
150 mm
(5.91 in)
Front
Recommended Panel Cutout Dimensions
144 mm
(5.66 in)
4.8 mm dia.
(0.188 in)
PV550 Touch Screen Terminals
165 mm
(6.49 in)
158 mm
(6.20 in)
R 1.8 mm
(0.07 in)
98 mm
(3.86 in)
Recommended Panel Cutout Dimensions
125 mm
(4.91 in)
Publication 2711-6.1
Installing the PV550 in a Panel
Installing the PV550 Terminal
7-5
To install the PV550 terminal in a panel:
!
ATTENTION: Disconnect all electrical power from the panel before making the cutout.
Make sure the area around the panel cutout is clear.
Do not allow metal cuttings to enter any components that may already be installed in the panel.
Failure to follow this warning may result in personal injury or damage to the panel components.
1. Cut an opening in the panel using the panel cutout provided with the terminal. Remove any sharp edges or burrs.
2. Make sure the terminal sealing gasket is properly positioned on the terminal as shown below. This gasket forms a compression type seal. Do not use sealing compounds.
Sealing Gasket
Adhesive Legend Strip
(Keypad and Keypad &Touch Screen Terminals only)
3. On the keypad and keypad & touch screen terminals, secure the ends of the legend strips to the legend strip adhesive.
4. Place the terminal in the panel cutout.
5. Verify that the opening is the proper size to clear the bezel and to allow the gasket to contact the panel.
6. On the keypad and keypad & touch screen terminals, position the ends of the legend inserts behind the panel cutout.
7. Install the self-locking nuts hand tight.
Publication 2711-6.1
7-6
Installing the PV550 Terminal
PV550 Keypad, Keypad & Touch Screen Terminals.
Mounting Studs (3 Top, 3 Bottom)
Protective installation label
Self-locking nuts
(6 used, 8 provided)
PV550 Touch Screen Terminal
Protective installation label
Mounting Studs (2 left, 2 right)
Self-locking nuts
(4 used, 8 provided)
8. Alternately tighten the self-locking nuts until the terminal is held firmly against the panel. Tighten nuts to a torque of 10 inchpounds. Do not over-tighten.
!
ATTENTION: Mounting nuts must be tightened to a torque of 10 inch-pounds to provide a proper seal and to prevent potential damage to the terminal. Allen-
Bradley assumes no responsibility for water or chemical damage to the terminal or other equipment within the enclosure because of improper installation.
9. Remove the protective installation label covering the top vents of the terminal.
!
ATTENTION: Failure to remove the protective installation label covering the top vents could result in overheating and damage to the terminal.
Publication 2711-6.1
Chapter Objectives
Hazardous Locations
Enclosures
Chapter
8
Installing the PV600 Terminal
This chapter describes how to mount the PV600 terminal in a panel or enclosure including:
• hazardous locations
• enclosures
• required tools
• mounting dimensions
• cutout dimensions
• clearances
• installing the PV600 terminal in a panel
See the nameplate label on terminal for certifications on hazardous locations.
!
ATTENTION: In Class 1, Division 2 Hazardous locations, the PanelView terminal must be wired per the
National Electric Code as it applies to hazardous locations. Peripheral equipment must also be suitable for the location in which it is installed.
The PV600 terminals have an operating temperature code of T4
(maximum operating temperature of 135
°
C or 275° F). Do not install the terminals in environments where atmospheric gases have ignition temperatures less than 135° C (275° F).
Mount the PV600 terminal in a panel or enclosure to protect the internal circuitry. The terminal meets NEMA Type 12/13 and 4X
(indoor ruse) ratings only when mounted in a panel or enclosure with the equivalent rating.
Allow enough space within the enclosure for adequate ventilation.
Consider heat produced by other devices in the enclosure. The ambient temperature around the terminals must be between:
• 0° and 55° C (32° and 131° F) for the PV600 keypad or keypad
& touch screen terminal
• 0° and 50° C (32° and 122° F) for the PV00 touch screen only terminal
Make provisions to access the back panel of the terminal for wiring, maintenance, installing a memory card and troubleshooting.
Publication 2711-6.1
8-2
Installing the PV600 Terminal
Required Tools
Mounting Dimensions
Other than the tools required to make the PV600 panel cutout, the tools required for installation are:
• small slotted screwdriver
• torque wrench (in. / lbs)
• #2 phillips screwdriver
• #2 phillips bit for torque wrench
The illustration below shows mounting dimensions for the PV600 terminals.
PV600 Keypad, Keypad & Touch Screen Terminals
6.9 mm
(0.27 in)
Top View
192 mm
(7.55 in)
91 mm
(3.60 in)
116 mm
(4.57 in)
290 mm
(11.40 in)
PV600 Touch Screen Terminals
Top View
152 mm
(6.00 in)
79 mm
(3.12 in)
96 mm
(3.80 in)
185 mm
(7.28 in)
Publication 2711-6.1
Cutout Dimensions
Installing the PV600 Terminal
8-3
Use the full size template shipped with the PV600 terminal to mark the cutout dimensions. Below is a reduce size cutout.
PV600 Keypad, Keypad & Touch Screen Terminals
167 mm
(6.57 in)
Recommended Panel Cut-out Dimensions
264 mm
(10.39 in)
PV600 Touch Screen Terminals
4.8 mm dia.
(0.188 in)
165 mm
(6.49 in)
158 mm
(6.20 in)
R 1.8 mm
(0.07 in)
98 mm
(3.86 in)
Recommended Panel Cutout Dimensions
125 mm
(4.91 in)
Publication 2711-6.1
8-4
Clearances
Installing the PV600 Terminal
51 mm (2.0 in) for Mounting and Air Flow
When installing the PV600 terminal, allow adequate space for mounting, air flow, maintenance, memory card and legend strip installation.
PV600 Keypad and Keypad & Touch Screen Terminals
Side, Top and Bottom Clearances
6.9 mm
(0.27 in)
Back Clearance
25 mm (1.0 in) for Mounting and Air Flow
Terminal Cutout - Front View
Use full size template shipped with terminal
91 mm
(3.60 in)
51 mm (2.0 in) for Mounting and Wiring Connections
38 mm (1.5 in) for Mounting, Air Flow and Legend Insert
Card
Memory Card Retainer
220 mm (8.65 in) is required to insert and remove a memory card with the memory card retainer.
25 mm (1.0 in) for Mounting and Air Flow
PV600 Touch Screen Terminals
Side, Top and Bottom Clearances
Back Clearance
Terminal Cutout
Use full size template shipped with terminal
79 mm
(3.12 in)
Memory Card Retainer
132 mm
(5.21 in)
211 mm (8.30 in.) is required to insert and remove a memory card with the memory card retainer.
38 mm (1.5 in) for Mounting, Air Flow and Wiring Connections
Publication 2711-6.1
Installing the PV600 in a Panel
Installing the PV600 Terminal
8-5
To install the PV600 terminal in a panel:
!
ATTENTION: Disconnect all electrical power from the panel before making the cutout.
Make sure the area around the panel cutout is clear.
Do not allow metal cuttings to enter any components that may already be installed in the panel.
Failure to follow this warning may result in personal injury or damage to the panel components.
1. Cut an opening in the panel using the panel cutout provided with the terminal. Remove any sharp edges or burrs.
2. Make sure the terminal sealing gasket is properly positioned on the terminal as shown below. This gasket forms a compression type seal. Do not use sealing compounds.
Sealing Gasket
3. Although the keypad legend strip can be installed on the keypad and keypad & touch screen terminals at any time, we recommend that you install the strip after the terminal is installed.
4. Place the terminal in the panel cutout.
Publication 2711-6.1
8-6
Installing the PV600 Terminal
PV600 Touch Screen Terminal
1 Protective installation label
5. Install the 4 mounting clips (2 on top, 2 on bottom). The ends of the clips slide into the slots on the terminal. Tighten the clip mounting screws by hand until the gasket seal contacts the mounting surface uniformly.
PV600 Keypad, Keypad & Touch Screen Terminal
2 Protective installation labels
Install 4 mounting clips:
Top - left and right slots
Bottom - left and right slots
Self-Locking Nuts
(4 used, 8 provided)
Mounting Studs
(2 left / 2 right)
6. Alternately tighten the self-locking nuts or mounting clip screws until the terminal is held firmly against the panel.Tighten the nuts or screws to a torque of 10 inch-pounds. Do not over-tighten.
!
ATTENTION: Tighten nuts or mounting clips to a torque of 10 inch-pounds to provide a proper seal and to prevent potential damage to the terminal. Allen-
Bradley assumes no responsibility for water or chemical damage to the terminal or other equipment within the enclosure because of improper installation.
7. Remove the protective installation labels covering the top vents of the terminal.
!
ATTENTION: Remove the protective installation labels covering the top vents to prevent overheating and damage to the terminal.
Publication 2711-6.1
Chapter Objectives
Hazardous Locations
Enclosures
Chapter
9
Installing the PV900/1000 Terminals
This chapter describes how to mount the PV900 and PV1000 terminals in a panel or enclosure including:
• hazardous locations and enclosures
• required tools
• mounting dimensions
• clearances
• cutout dimensions
• installing the PV900/PV1000 terminal in a panel
See the nameplate label on terminal for certifications on hazardous locations.
!
ATTENTION: In Class 1, Division 2 Hazardous locations, the PanelView terminal must be wired per the
National Electric Code as it applies to hazardous locations. Peripheral equipment must also be suitable for the location in which it is installed.
The PV900/PV1000 terminals have an operating temperature code of
T4 (maximum operating temperature of 135
°
C or 275° F). Do not install the terminals in environments where atmospheric gases have ignition temperatures less than 135° C (275° F).
The PV900/PV1000 terminal must be mounted in an environment that provides IEC-1131-2 Pollution degree 2 protection.
Mount the terminal in a panel or enclosure to protect the internal circuitry. The terminal meets NEMA Type 12/13 and 4X (indoor ruse) ratings only when mounted in a panel or enclosure with the equivalent rating.
Allow enough space within the enclosure for adequate ventilation.
Consider heat produced by other devices in the enclosure. The ambient temperature around the terminals must be between 0° and
55° C (32° and 131° F).
Make provisions to access the back panel of the terminal for wiring, maintenance, installing a memory card and troubleshooting.
Publication 2711-6.1
9-2
Installing the PV900/1000 Terminals
Required Tools
Mounting Dimensions
Other than the tools required to make the panel cutout, the tools required for installation are:
• small slotted screwdriver
• torque wrench (in. / lbs) with slotted or phillips head driver
PV900 Terminals
The illustrations below show mounting dimensions for the PV900 monochrome and color terminals.
PV900 Touch Terminal Mounting Dimensions
6.9 mm
(0.27 in)
Top View
249 mm
(9.80 in)
90 mm
(3.54 in)
112 mm
(4.40 in)
336 mm
(13.24 in)
PV900 Keypad Terminal Mounting Dimensions
6.9 mm
(0.27 in)
Top View
249 mm
(9.80 in)
90 mm
(3.54 in)
406 mm
(15.97 in)
112 mm
(4.40 in)
Publication 2711-6.1
Installing the PV900/1000 Terminals
PV1000 Terminals
The illustrations below show the mounting dimensions for the
PV1000 grayscale and color terminals.
PV1000 Touch Terminal Mounting Dimensions
9-3
6.9 mm
(0.27 in)
282 mm
(11.11 in)
90 mm
(3.54 in)
Top View
112 mm
(4.40 in)
370 mm
(14.58 in)
PV1000 Keypad Terminal Mounting Dimensions
6.9 mm
(0.27 in)
282 mm
(11.11 in)
90 mm
(3.54 in)
Top View
112 mm
(4.40 in)
423 mm
(16.64 in)
Publication 2711-6.1
9-4
Clearances
Installing the PV900/1000 Terminals
Allow adequate space for mounting, air flow, maintenance, memory card and legend strip installation.
Important: If using a memory card and/or memory card retainer, allow a back clearance to load the card.
Side, Top and Bottom Clearances
Leave 51 mm (2.0 in) for Mounting and Air Flow
Leave 51 mm (2.0 in) for Mounting and Air Flow
Terminal Cutout - Front View
Use full size template shipped with terminal
Leave 51 mm (2.0 in) for Mounting, Air Flow and Legend Insert
Leave 51 mm (2.0 in) for Mounting and Wiring Connections
Back Clearance
Memory Card Retainer
6.9 mm
(0.27 in)
90 mm
(3.54 in)
Card
222 mm (8.73 in) is required to insert and remove a memory card with the memory card retainer.
Publication 2711-6.1
Cutout Dimensions
Installing the PV900/1000 Terminals
9-5
Use the full size template shipped with the PV900 and PV1000 terminals to mark the cutout dimensions. The following illustrations show reduced cutouts for these terminals with dimensions.
PV900 Panel Cutout Dimensions
PV900 Keypad Terminals
PV900 Touch Screen Terminals
224 mm
(8.8 in)
Recommended Panel Cut-out Dimensions
224 mm
(8.8 in)
Recommended Panel Cut-out Dimensions
375 mm
(14.75 in)
305 mm
(12.00 in)
PV1000 Panel Cutout Dimensions
PV1000 Keypad Terminals
PV1000 Touch Screen Terminals
257 mm
(10.11 in)
Recommended Panel Cut-out Dimensions
257 mm
(10.11 in)
Recommended Panel Cut-out Dimensions
390 mm
(15.35 in)
338 mm
(13.29 in)
Publication 2711-6.1
9-6
Installing the PV900/1000 Terminals
Installing the
PV900/PV1000 in a Panel
To install the PV900/PV1000 terminal in a panel:
!
ATTENTION: Disconnect all electrical power from the panel before making the cutout.
Make sure the area around the panel cutout is clear.
Do not allow metal cuttings to enter any components that may already be installed in the panel.
Failure to follow this warning may result in personal injury or damage to the panel components.
1. Cut an opening in the panel using the panel cutout provided with the terminal. Remove any sharp edges or burrs.
2. Make sure the terminal sealing gasket is properly positioned on the terminal as shown below. This gasket forms a compression type seal. Do not use sealing compounds.
Sealing Gasket
3. Although the keypad legend strip can be installed any time, we recommend that you install it after the terminal is installed.
4. Place the terminal in the panel cutout.
Publication 2711-6.1
Installing the PV900/1000 Terminals
9-7
5. Install the 6 mounting clips (2 on top, 2 on bottom, 1 on each side). The ends of the clips slide into the slots on the terminal.
Tighten the clip mounting screws by hand until the gasket seal contacts the mounting surface uniformly.
Protective installation labels
Install 6 mounting clips:
Top - left and right slots
Bottom - left and right slots
Sides - left and right
6. Alternately tighten the mounting clip screws to a torque of 10 inch-pounds. Do not over-tighten.
!
ATTENTION: Tighten mounting clips to a torque of
10 inch-pounds to provide a proper seal and to prevent potential damage to the terminal. Allen-Bradley assumes no responsibility for water or chemical damage to the terminal or other equipment within the enclosure because of improper installation.
7. Remove the 2 protective labels covering the top vents of the terminal.
!
ATTENTION: Remove the protective installation labels covering the top vents to prevent overheating and damage to the terminal.
Publication 2711-6.1
9-8
Installing the PV900/1000 Terminals
Publication 2711-6.1
Chapter Objectives
Enclosures
Required Tools
Chapter
10
Installing the PV1400 Terminal
This chapter describes how to mount the PV1400 terminal in a panel or enclosure including:
• enclosures
• recommended tools
• mounting dimensions
• clearances
• cutout dimensions
• installing the PV1400 terminal in a panel
The PV1400 terminal must be mounted in an environment that provides IEC-1131-2 Pollution degree 2 protection.
Mount the PV1400 terminal in a panel or enclosure to protect the internal circuitry. The terminal meets NEMA Type 12/13 and 4X
(indoor ruse) ratings only when mounted in a panel or enclosure with the equivalent rating.
Allow enough space within the enclosure for adequate ventilation.
Consider heat produced by other devices in the enclosure. The ambient temperature around the terminals must be between 0° and
55° C (32° and 131° F).
Make provisions to access the back sides of the terminal. Access is required for wiring, routine maintenance, adjusting brightness/ contrast, installing a memory card and troubleshooting.
In addition to the tools required to make the panel cutout, you need the tools below.
For clip mounting:
• socket screwdriver (phillips head or slotted)
• 16-inch (406 am) extension rod (minimum)
• socket driver (in/lab torque wrench recommended)
For stud mounting:
• 7/32 and 3/8 inch socket
• 16-inch (406 mm) extension rod (minimum)
• socket driver (in/lb torque wrench recommended)
Publication 2711-6.1
10-2
Installing the PV1400 Terminal
Mounting Dimensions
The illustrations below show mounting dimensions for the PV1400 terminals.
PV1400 Touch Terminal Mounting Dimensions
3.3 mm
(0.13 in)
Top View
355 mm
(13.97 in)
370 mm
(14.58 in)
394 mm
(15.53 in)
441 mm
(17.37 in)
PV1400 Keypad Terminal Mounting Dimensions
3.3 mm
(0.13 in)
Top View
355 mm
(13.97 in)
370 mm
(14.58 in)
394 mm
(15.53 in)
483 mm
(19.0 in)
Publication 2711-6.1
Clearances
Installing the PV1400 Terminal
10-3
Allow adequate space for mounting, air flow, maintenance, adjusting brightness/contrast, memory card and legend strip installation.
Important: If using a memory card, allow a back clearance to load the card.
Side, Top and Bottom Clearances
Leave 51 mm (2.0 in) for Mounting and Air Flow
Terminal Cutout - Front View
Use full size template shipped with terminal
Leave 51 mm (2.0 in) for Mounting
Back Clearance
Leave 51 mm (2.0 in) for Mounting and Air Flow
3.3 mm
(0.13 in)
370 mm
(14.58 in)
Approximately
400 mm (15.74 in) is required to insert and load a memory card.
Card
Publication 2711-6.1
10-4
Installing the PV1400 Terminal
Cutout Dimensions
170 mm
(6.70 in)
Use the full size template provided with the terminal to mark cutout dimensions. The illustration below shows reduced size cutouts with dimensions.
PV1400 Keypad Terminals
419 mm
(16.50 in)
110 mm
(4.35 in)
221 mm
(8.70 in)
7/32 in (5.56 mm) Typical
18 Holes
140 mm
(5.50 in)
38mm
1.50 in
305 mm
(12.0 in)
Ignore stud holes if mounting terminal using panel clips.
Ignore stud holes if mounting terminal using panel clips.
169 mm
(6.65 in)
PV1400 Touch Screen Terminals
391 mm
(15.40 in)
127 mm
(5.0 in)
233 mm
(9.16 in)
7/32 in (5.56 am) Typical
18 Holes
140 mm
(5.50 in)
305 mm
(12.0 in)
212 mm
(8.35 in)
Publication 2711-6.1
Installing the PV1400 in a Panel
Installing the PV1400 Terminal
10-5
This section gives procedures for mounting a PV1400 using:
• mounting clips (10 shipped with terminal, 10 required)
• mounting studs (ordered separately, Catalog No. 2711-NP3)
!
ATTENTION: Disconnect all electrical power from the panel before making the cutout.
Make sure the area around the panel cutout is clear.
Do not allow metal cuttings to enter any components that may already be installed in the panel.
Failure to follow this warning may result in personal injury or damage to the panel components.
To install the PV1400 terminal in a panel using clips:
1. Cut an opening in the panel using the panel cutout provided with the terminal. Remove any sharp edges or burrs. Do not drill the mounting stud holes if you are using clips.
2. Make sure the sealing gasket is properly positioned on the terminal as shown below. This gasket forms a compression type seal.
Do not use sealing compounds.
Sealing Gasket
3. Although the keypad legend strip can be installed any time, we recommend that you install them after the terminal is installed.
4. Place the PV1400 in the panel cutout. The terminal will snap into the panel as the temporary retaining tabs lock against the panel.
Note: The PV1400 has 2 metal tabs (on bottom edge) that temporarily lock the terminal against the panel. These tabs only facilitate installation of the mounting hardware. The tabs are not designed to provide permanent mounting.
Publication 2711-6.1
10-6
Installing the PV1400 Terminal
5. Install the 10 mounting clips (3 on top, 3 on bottom, 2 on each side). The ends of the clips slide into slots on the terminal.Tighten
the clip mounting screws hand tight.
Install 10 Mounting Clips
= Recommended
Placement
Keypad Version
Touch Screen Version
6. Alternately tighten the mounting clip screws until the terminal is held firmly against the panel. Tighten mounting screws to a torque of 10 inch-pounds. Do not over-tighten.
!
ATTENTION: Tighten mounting clips to a torque of
10 inch-pounds to provide a proper seal and to prevent potential damage to the terminal. Allen-Bradley assumes no responsibility for water or chemical damage to the terminal or other equipment within the enclosure because of improper installation.
Publication 2711-6.1
Installing the PV1400 Terminal
10-7
To install the PV1400 terminal in a panel using mounting studs:
1. Cut an opening in the panel using the panel cutout shipped with the terminal. Carefully drill 5.56 mm (7/32 inch) holes for studs as indicated.
2. Install the mounting studs (Catalog No. 2711-NP3) using a 7/32inch socket on the end of the stud. Turn stud clockwise and tighten to approximately 10-inch pounds (1.1 N•m).
Gasket
Bezel
Mounting Studs
(Qty 18 for Keypad, 12 for Touch)
Panel or Enclosure
Self-locking Nuts
Spacer
3. Make sure the sealing gasket is properly positioned on the terminal. This gasket forms a compression type seal (NEMA Type 4).
Do not use sealing compounds
!
ATTENTION: Be careful not to damage the sealing gasket when installing or removing studs. A damaged seal may result in damage to the PanelView terminal and other panel components due to a leaking seal.
4. Place the PV1400 in the panel cutout aligning the studs with the mounting holes.
Publication 2711-6.1
10-8
Installing the PV1400 Terminal
5. Install the self-locking nuts hand tight.
!
ATTENTION: Tighten mounting nuts to a torque of
10 inch-pounds (1.1 N•m) to provide a proper seal and prevent potential damage to the terminal. Allen-Bradley assumes no responsibility for water or chemical damage to the terminal or other equipment within the enclosure because of improper installation.
6. Alternately tighten the self-locking nuts (use 3/8 inch socket) until the PV1400 is held firmly against the panel. (The recommended tightening sequence is shown below).
The studs have an integral spacer that prevents the gasket from being over-compressed. The amount of torque required increases significantly as the gasket reaches the proper compression.
Tighten nuts to a torque of 10 inch-pounds (1.1 N•m).
16
18
4
9 1 5
Recommended
Torque Sequence
Keypad Terminals
7
12
13
15
3
8
11
17 10 2 6 14
7
4
12
9 1
Recommended
5
Torque Sequence
Touch Terminals
8
3
11
10 2 6
Note that sequence starts at center studs and continues to the corner studs.
Publication 2711-6.1
Chapter Objectives
Wiring and Safety Guidelines
Chapter
11
Making Terminal Connections
This chapter describes network and device connections for PanelView terminals.
• wiring and safety guidelines
• Remote I/O connections
• DH+ connections
• DH-485 connections
• RS-232 (DH-485) connections
• ControlNet connections
• DeviceNet connections
• DF1 connections
• Computer or printer connection to RS-232 serial port
Use publication NFPA 70E, Electrical Safety Requirements for
Employee Workplaces when wiring the PanelView terminals. In addition to the NFPA general guidelines:
• route communication cables to terminal by a separate path from incoming power.
ATTENTION: Do not run signal wiring and power wiring in the same conduit.
!
• where power and communication lines must cross, they should cross at right angles. Communication lines can be installed in the same conduit as low level DC I/O lines (less than 10 volts).
• grounding minimizes noise from Electromagnetic Interference
(EMI) and is a safety measure in electrical installations.
• use the National Electric Code published by the National Fire
Protection Association as a source for grounding.
Publication 2711-6.1
11-2
Making Terminal Connections
Remote I/O Terminal Connections
This section describes connections for the Remote I/O PanelView terminals including:
• Remote I/O port
• supported controllers
• making Remote I/O connections
• Remote I/O Pass-Through
Remote I/O Terminal Ports
The Remote I/O versions of the PanelView terminal (catalog numbers ending in 1) have a Remote I/O port and an RS-232 port.
Use the Remote I/O port to:
• communicate with the Remote I/O scanner port on a PLC controller
• communicate with SLC controllers using a 1747-SN Remote I/O scanner module
• communicate with other Remote I/O scanners
• transfer applications using Remote I/O Pass-Through
Use the RS-232 Port to:
• transfer PanelView applications between a computer and the terminal.
• connect a printer.
For details on connecting to the RS-232 port, see the last section in this chapter.
PanelView 550
Keypad (2711-K5A1) Shown
PanelView 1000
Keypad (2711-K10C1) Shown
Remote I/O Port
RS-232 Port
Remote I/O Port RS-232 Port
Publication 2711-6.1
Making Terminal Connections
11-3
Supported Controllers
The Remote I/O terminal connects to any Allen-Bradley 1771
Remote I/O link. Applicable host controllers include almost all Allen-
Bradley PLCs, computers, VME controllers, and DEC Q-Bus controllers with a Remote I/O scanner module. New PLC product releases that support 1771 Remote I/O will also work with
PanelView.
When connecting a PanelView terminal to a controller refer to the user manual for your controller or scanner module for connection diagrams and any Remote I/O limitations. The table below provides a summary of possible connections.
Controller Scanner Comments
PLC-5/11, 5/15
5/20, 5/25,
5/30, 5/60, 5/250
PLC-5/10, 5/12
PLC-2
PLC-3 and
PLC-3/10
SLC-5/00, 5/02,
5/03, 5/04,
5/05
1
,
PLC Integral
1771-SN
1771-SN
1771-SN or
1772-SD2
None
PLC-3/10
Remote I/O
Scanner
1747-SN
3
2
Connect PanelView terminals directly to the Remote I/O port (scanner mode). Connect PanelView terminals through the 1771-SN subscanner module.
Connect PanelView terminals through the 1771-SN subscanner module.
Connect PanelView terminals to the
PLC-2 family of processors through a
1771-SN I/O subscanner module.
Connect PanelView terminals directly to a PLC-3.
Connect PanelView terminals to the
PLC-3/10 through the Remote I/O scanner.
Connect PanelView terminals through the 1747-SN subscanner module. Each module provides an additional Remote I/O link for up to 4 racks.
Important: Only Series B and later versions of the 1747-SN subscanner support block transfers.
IBM PC 6008-SI 6008-SI I/O scanner is compatible with IBM PC or compatible computers. The scanner provides a computer access to the 1771 Remote I/O link.
VME 6008-SV 6008-SV I/O scanner provides access to the 1771 Remote I/O link for VME controllers.
DEC Q-BUS 6008-SQ 6008-SQ I/O scanner provides access to the 1771 Remote I/O link for DEC Q-BUS controllers.
1
If using a PLC-5/15 with partial rack addressing and block transfers, you must use Series B, Rev. J or later.
2
If using a 1775-SD2 Remote Scanner/Distribution Panel, use revision 3 or later.
3
If using a 1775-S4A Remote Scanner/Distribution Panel, user Series B or later.
Publication 2711-6.1
11-4
Making Terminal Connections
Making Remote I/O Connections
To connect a PanelView terminal to a Remote I/O scanner, use cable
Catalog No. 1770-CD (equivalent to Belden 9463). The maximum cable length (link distance) is determined by the baud rate.
• 2,800 meters (10,000 feet) for 57.6K baud
• 1,400 meters (5,000 feet) for 115.2K baud
• 700 meters (2,500 feet) for 230.4K
See Programmable Controller Wiring and Grounding Guidelines
(Publication 1770-4.1). The user manual for the I/O scanner module also provides cabling information.
PanelView 550
Keypad (2711-K5A1) Shown
PanelView 1000
Keypad (2711-K10C1) Shown
Remote I/O Port
3-pin Terminal Block Connector
Clear = 2
Shield
Blue = 1
To PLC or Scanner Remote I/O Port
Connector
(One provided with each terminal)
Cable (Catalog No. 1770-CD)
Note: The polarity of the Remote I/O Connector on the PanelView terminal is reversed from the PLC Scanner connector. However, the polarity is the same as the scanner card connection to the SLC.
Publication 2711-6.1
Making Terminal Connections
11-5
Remote I/O Pass-Through
Remote I/O terminals allow the transfer of applications from a computer on the Allen-Bradley DH+ link to a PLC-5 controller. The controller passes data to the PanelView terminal over the Remote I/O network.
PLC-5
DH+
Computer
Remote I/O
Pass-Through
Remote I/O Network
PanelView
To transfer an application using Remote I/O Pass-Through:
1. A Data Highway Plus Interface Module must be installed in the computer. Allen-Bradley offers a variety of interface cards for a
DH+ connection between a computer and a controller.
2. The appropriate communication driver must be configured on the computer.
3. Connect the computer to the PLC. See the instruction sheets provided with the communication module or card to select the proper cable. Connect the cable between the computer and the controller.
4. Pass-Through must be enabled for the terminal. Check the RIO
Configuration screen on the terminal’s Configuration Mode menu. Pass-Through is enabled using the out-of-box application provided with the terminal or when defining Remote I/O parameters in the PanelBuilder32 software.
5. Refer to the online help in the PanelBuilder32 software for procedures on how to transfer applications using Pass-Through.
Publication 2711-6.1
11-6
Making Terminal Connections
DH-485 Terminal Connections
This section describes connections for the DH-485 PanelView terminals.
• DH-485 terminal ports
• Connecting to a single SLC controller (Point-to-Point)
• Connecting to a DH-485 network
• Connecting a Hand-held terminal
• Connecting a computer
DH-485 Terminal Ports
DH-485 PanelView terminals with catalog numbers ending in 2 have two DH-485 ports. Terminals with catalog numbers ending in 3 also have an RS-232 printer port.
Use the DH-485 Communications port to:
• communicate with a single or multiple SLC controllers over a
DH-485 network.
Use the DH-485 SLC Programming connector to:
• upload/download PanelView applications
• monitor SLC operation, enter/modify SLC programs, test network devices
Use the RS-232 Printer port to:
• connect a printer that supports the IBM enhanced character set.
For details on connecting to the RS-232 port, see the last section in this chapter.
The DH-485 communications port and programming connector may appear in different locations on specific terminals. Identify the ports by their size and shape or by the port labels.
PanelView 550
Keypad (2711-K5A3) Shown
PanelView 1000
Keypad (2711-K10C3) Shown
RS-232 Printer Port DH-485
DH-485 SLC
Communications Port
Programming Connector
RS-232 Printer Port
DH-485 SLC
Programming Connector
DH-485
Communications Port
Publication 2711-6.1
Making Terminal Connections
11-7
Connecting to a Single SLC Controller (Point-to-Point)
To connect a DH-485 terminal to a single SLC controller use one of these cables:
• 0.3 meter (1 foot) Catalog No. 1747-C11
• 1.83 meter (6 foot) Catalog No. 1747-C10
• 6.1 meter (20 foot) Catalog No. 1747-C20
PanelView 1000
Touch Screen (2711-T10C3) Shown
SLC
SLC 500
Communications Connector
Pin 1
DH-485 Communications Port
Pin 8
Cable, Catalog No. 1747-C10
Cable, Catalog No. 1747-C11
Cable, Catalog No. 1747-C20
Pin 1
Pin 8
Side shown is opposite latch
To PanelView Terminal
8-pin Female Plug
Connection Diagram
Pin #
Pin #
Connect to:
5
6
3
4
7
8
1
2
5
6
7
3
4
1
2
8
To SLC Communications Connector
8-pin, Male, Modular Plug
The DH-485 connectors are not electrically isolated. If electrical isolation is required, use Link Couplers (Catalog No. 1747-AIC) as shown on next page.
!
ATTENTION: Electrical isolation using Link
Couplers (Catalog No. 1747-IC) is required where the distance between the PanelView terminal and the SLC is greater than 6.1 meters (20 feet).
Publication 2711-6.1
11-8
Making Terminal Connections
Connecting to a DH-485 Network
This section shows how to connect a DH-485 terminal to multiple
SLC controllers on a DH-485 network through the AIC Link Coupler.
Link Coupler
Catalog No. 1747-AIC
Network with Link Couplers
SLC
PanelView 1000
Touch Screen (2711-T10C3) Shown
Power Source or 1747-NP1
Belden 9842
Cable-
Catalog No. 1747-C10
Catalog No. 1747-C11
Catalog No. 1747-C20
SLC 5/01
Important: The DH-485 network cable requires proper shielding, grounding and termination. Refer to Data Highway / Data
Highway Plus / Data Highway-485 Cable Installation
Manual (Publication No. 1770-6.2.2).
Publication 2711-6.1
Making Terminal Connections
11-9
The illustration below shows how to connect a DH-485 terminal to a
MicroLogix or SLC controller using the AIC+ Link Coupler (Catalog
No. 1761-NET-AIC).
AIC+
Catalog No. 1761-NET-AIC
Cable-
Catalog No. 1761-CBL-AS03
Catalog No. 1761-CBL-AS09
MicroLogix 1000
Catalog No.
1761-CBL-HM02
1761-CBL-AM00
PanelView 1000
Touch Screen (2711-T10C3) Shown
PanelView 1000
Touch Screen (2711-T10C3) Shown
SLC 5/03, 5/04, 5/05
AIC+
Catalog No. 1761-NET-AIC
Cable-
Catalog No. 1761-CBL-AS03
Catalog No. 1761-CBL-AS09
Channel 0 Port
Catalog No. 1747-CP3
To 24V DC Power
To PanelView
AIC
Catalog No. 1747-AIC
AIC+
Catalog No. 1761-NET-AIC
Belden 9842
MicroLogix 1000
Catalog No.
1761-CBL-HM02
1761-CBL-AM00
PanelView 1000
Do not connect the PanelView to
Port 3 of the AIC+ when Port 3 is networked to other devices.
Cable-
Catalog No. 1747-C10
Catalog No. 1747-C11
Catalog No. 1747-C20
Publication 2711-6.1
11-10
Making Terminal Connections
Connecting a Computer
On DH-485 terminals, PanelView applications are transferred:
• through the DH-485 programming connector to the terminal.
• through any node on a DH-485 network.
To connect a computer to the PanelView terminal, you need:
• a cable (same cables used to transfer applications from APS software to SLC)
- 0.3 meter (1 foot) cable, Catalog No. 1747-C11
- 1.83 meter (6 foot) cable, Catalog No. 1747-C10
- 6.1 meter (20 foot) cable, Catalog No. 1747-C20
• Personal Computer Interface Converter (PIC), Catalog No. 1747-
PIC. The PIC connects to the computer. The cable connects the
PIC to the DH-485 programming connector.
Personal Computer Interface Converter (PIC)
The Personal Computer Interface Converter (PIC) receives power from a controller through DH-485 connections. When connecting a computer directly to a PanelView terminal without a controller connected, you need to use a power supply (Catalog No. 1747-NP1).
The power supply connects to the DH-485 communications connector with the same cables used to connect an SLC.
Important: The terminal must be connected to an SLC, DH-485 network, or power supply (Catalog No. 1747-NP1). This connection provides power to the PIC.
Connecting Earth Ground to PanelView Terminals
When using the 1747-PIC converter with the PV600, PV900, PV1000 color and PV1000 grayscale terminals, you must connect the Earth
Ground terminal on the back of the terminal to Earth Ground.
Connect the Earth Ground terminal using 14-gauge, stranded wire no longer than 1 meter (40 inches).
Earth Ground Terminal
PV900 Color Terminals
Publication 2711-6.1
Making Terminal Connections
11-11
Connecting a Computer to DH-485 Connector using a Power Supply
PanelView 1000
Touch Screen (2711-T10C3) Shown
PanelBuilder32
Wallmount Power Supply
(Catalog No. 1747-NP!)
To DH-485
Programming Connector
To DH-485
Communications Port
25-pin to 9-pin Adapter
(if required)
Personal Computer
Interface Converter
(Catalog No. 1747-PIC)
Cable
Catalog No. 1747-C10
Catalog No. 1747-C11
Catalog No. 1747-C20
Connecting a Computer to DH-485 Connector using a DH-485 Powered Device
PanelView 1000
Touch Screen (2711-T10C3) Shown
PanelBuilder32
To DH-485
Programming Connector
To DH-485
Communications Port
SLC 500 or
DH-485 Network
(if required)
25-pin to 9-pin Adapter
Personal Computer
Interface Converter
(Catalog No. 1747-PIC)
Note: The computer can connect to any node on the network. It is not necessary to directly connect the computer to the PanelView terminal.
Cable
Catalog No. 1747-C10
Catalog No. 1747-C11
Catalog No. 1747-C20
Publication 2711-6.1
11-12
Making Terminal Connections
Connecting a Hand-Held Terminal
To connect a Hand-Held Terminal (HHT) to the PanelView terminal, use cable Catalog No. 1747-C10. One end of the cable connect to the
HHT connector and the other end connects to the DH-485 programming connector on the terminal. All power is supplied to the
HHT through the cable.
Important: The PanelView terminal must be connected to an SLC,
DH-485 network or power supply. This connection provides power for the HHT.
Hand-Held Terminal
Catalog No. 1747-PT1
PanelView 1000
Touch Screen (2711-T10C3) Shown
To DH-485
Programming Connector
DH-485 Communications Port
Must be connected to an SLC, DH-485 network, or wallmount power supply (Cat. No. 1747-NP1) to provide power for the HHT.
Cable, 1.83 meters (6 feet) Catalog No. 1747-C10
Publication 2711-6.1
DH+ Terminal Connections
Making Terminal Connections
11-13
This section describes connections for the DH+ PanelView terminals including:
• DH+ connectors
• typical DH+ system configuration
• making DH+ connections
DH+ Terminal Ports
The DH+ versions of the PanelView terminals have a DH+ port and an RS-232 port.
Use the DH+ port to:
• communicate with a PLC-5 controller on the Allen-Bradley DH+ link via the processor’s DH+ port.
• communicate with an SLC 5/04 controller (Channel 0 port) on the
Allen-Bradley DH+ link via the processor’s DH+ port.
Use the RS-232 port to:
• transfer PanelView applications between a computer and the
DH+ terminal using a direct connection.
• connect a printer. For connection details, see the last section in this chapter.
PanelView 550
Keypad (2711-K5A8) Shown
PanelView 1000
Keypad (2711-K10C8) Shown
DH+ Port
RS-232 Port
DH+ Port
RS-232 Port
Publication 2711-6.1
11-14
Making Terminal Connections
SLC 5/04
Typical DH+ System Configuration
For more information on the Allen-Bradley DH+ link, refer to:
• 1785-5.7 Enhanced PLC-5 Programmable Controllers Installation
Instructions
• 1770-6.2.2 Data Highway/Data Highway Plus/Data Highway II/
Data Highway 485 Cable Installation Manual.
PLC-5
Download application to PanelView
1 over local DH+ link
2 over a direct serial link or
1
PanelView 1000 DH+ Terminal
DH+ RSLinx Port
DH+ communication card installed in computer
1
PanelView 550 DH+ Terminal
DH+ Port
DH+ Port
2
Serial Link
RS-232 Port
Computer for developing
PanelView applications
Publication 2711-6.1
Making Terminal Connections
11-15
Making DH+ Connections
Use the Belden 9463 twin axial cable (1770-CD) to connect a DH+
PanelView terminal to the DH+ link.
You can connect a DH+ link in 2 ways:
• trunk line/drop line - from the drop line to the connector screw terminals on the DH+ connectors of the processor
• daisy chain - to the connector screw terminals on the DH+ connectors on the processor
Follow these guidelines when installing DH+ communication links:
• do not exceed these cable lengths:
- trunk line-cable length: 3,048 m (10,000 cable ft)
- drop-cable length: 30.4 m (100 cable-ft)
• do not connect more than 64 stations on a single DH+ link
PLC-5/30, -5/40, -5/46, -5/40L, -5/60, -5/60C
-5/60L, -5/80, 5/80C, -5/86 Processor
PLC 5/11, -5/20, -5/26 Processor
PanelView 550 DH+ Terminal
Clear 1
Shield SH
Blue 2
2 1
1770-CD
(Belden Cable)
Blue 2
Shield SH
Clear 1
82
Ω or 150
Ω
=resistor
PanelView 1000 DH+ Terminal
2 1
Blue 2
Shield SH
Clear 1
82
Ω or 150
Ω =resistor
Publication 2711-6.1
11-16
Making Terminal Connections
RS-232 Terminal Connections
This section describes connections for the RS-232 PanelView terminals including:
• RS-232 ports
• connecting to Channel 0 of an SLC 5/03, 5/04, 5/05 Controller
(point-to-point)
• connecting to a MicroLogix Controller
• connecting a computer
• connecting to a DH+ link
RS-232 Terminal Ports
RS-232 versions of the PanelView terminals with catalog numbers ending in 5 have a single RS-232 communications port. Terminals with catalog numbers ending in 9 have an RS-232 communications port and an RS-232 printer port.
Use the RS-232 communications port to:
• communicate with a single SLC 5/03, 5/04, or 5/05 controller
(Channel 0 port) using point-to-point communications
• download/upload PanelView applications
Use the RS-232 printer port to:
• connect a printer that supports the IBM enhanced character set.
For connection details, see the last section in this chapter.
The RS-232 communications port and the printer port are reversed on the PanelView 550 touch screen terminals.
PanelView 550
Keypad (2711-K5A9) Shown
PanelView 1000
Keypad (2711-K10C9) Shown
RS-232 Printer Port
RS-232 Communications Port
RS-232 Printer Port
RS-232 Communications Port
Publication 2711-6.1
Making Terminal Connections
11-17
Connecting to an SLC 5/03, 5/04, 5/05 Controller (Point-to-Point)
This section shows how to connect an SLC-5/03, 5/04 or 5/05 controller to the RS-232 PanelView terminal for point-to-point communications. On terminals with two ports, use the RS-232
Communications Port.
Use one of these cables:
• 5 meter (16.4 foot) Catalog No. 2711-NC13
• 10 meter (32.7 foot) Catalog No. 2711-NC14
• 3 meter (10 foot) Catalog No. 2706-NC13
PanelView 1000
Touch Screen (2711-T10C9) Shown
SLC 5/03, 5/04, 5/05
RS-232 Communications Port
Channel 0 Port
RS-232 Connector
5
9 6
11
Cable, Catalog No. 2711-NC13
Cable, Catalog No. 2711-NC14
Cable, Catalog No. 2706-NC13
To PanelView Terminal
9-pin, Male, D-Shell Connector
Pin #
Required pins
Data Out (TXD)
Data In (RXD)
1
2
3
4
Signal Common
5
6
7
8
9
Pin #
1
8
9
6
7
4
5
2
3
5
9 6
1
To SLC 5/03, 5/04, 5/05 Channel 0 Port
9-pin, Male, D-Shell Connector
Data In (RXD)
Data Out (TXD)
Signal Common
Important: You must configure the Channel 0 Port of the SLC 5/03,
5/04, 5/05 controller for DH-485 communications using the RSLogix 500, or AI500 software.
Publication 2711-6.1
11-18
Making Terminal Connections
Connecting to a MicroLogix Controller
This section shows how to connect the RS-232 (DH-485) version of the PanelView terminal to a MicroLogix 1000 controller through an
AIC+ Link Coupler.
AIC+
Catalog No. 1761-NET-AIC
Belden Cable 9842
Catalog No. 1747-CP3
MicroLogix 1000
Catalog No.
1761-CBL-HM02
1761-CBL-AM00
PanelView 900
(2711-T9C9)
RS-232 Communications Cables
Catalog No. 2711-NC13
Catalog No. 2711-NC14
Catalog No. 2706-NC13
Computer
Note: On PanelView 550 terminals, pin 8 on the RS-232 connector is pulled high.
Do not use the 2711-NC13 cable.
Connecting a Computer
This section shows how to connect a computer to the RS-232 (DH-
485) PanelView terminal for transferring applications.
Computer
PanelView 1000
Touch Screen (2711-T10C9) Shown
PanelBuilder32
To Comm 1 or Comm 2 Port
To RS-232 Communications Port
9-pin to 25-pin Adapter
(if required)
RS-232 Communications Cables
Catalog No. 2711-NC13, 5 m (16.4 ft)
Catalog No. 2711-NC14, 10 m (32.7 ft)
Catalog No. 2706-NC13, 3 m (10 ft)
Publication 2711-6.1
Making Terminal Connections
11-19
Connecting to a DH+ to DH-485 Pass-Through Link
This section shows connections for transferring applications between a computer on the Allen-Bradley DH+ link and an RS-232 (DH-485)
PanelView terminal, through an SLC 5/04 controller.
The RS-232 (DH-485) Communications port on the terminal connects to the CH0 port of the controller using one of the cables listed below.
PanelView 1000
Touch Screen (2711-T10C9) Shown
Computer
PanelBuilder32
To 1784-KT/B Port
DH+ Network Cable
Catalog No. 1784-CP6 or
Catalog No. 1784-CP with 1784-CP7 Adapter
To RS-232 Communications Port
SLC 5/04 CPU
Cable
Catalog No. 2706-NC13,
2711-NC13,-NC14
To CH1 Port
To CH0 Port
Publication 2711-6.1
11-20
Making Terminal Connections
ControlNet Connections
This section describes connections for the ControlNet PanelView terminals including:
• ControlNet Protocol
• Compatible ControlNet Controllers
• ControlNet ports on the PanelView terminal
• Typical ControlNet network
• Making ControlNet connections
Related Information
For more information on ControlNet products, refer to the following publications.
• ControlNet System Overview (Publication 1786-2.9)
• ControlNet System Planning and Installation Manual (1786-
6.2.1)
• ControlNet Cable System Component List (AG-2.2)
The Allen-Bradley website (www.ab.com) provides information and product descriptions of ControlNet products. Under the Products and
Services heading, select Communications.
ControlNet Protocol
The PanelView terminal supports release 1.5 of ControlNet.
Unscheduled (peer) addressing of tags is supported. Scheduled (I/O) addressing is not supported.
ControlNet allows a flexible control architecture that can work with multiple processors and up to 99 nodes (via taps) anywhere along the trunk cable of the network. There is no minimum tap separation and you can access the ControlNet network from every node (including adapters).
Publication 2711-6.1
Making Terminal Connections
11-21
Compatible ControlNet Controllers
The ControlNet PanelView supports unscheduled PCCC
(Programmable Controller Communication Command) messaging with the following controllers:
• PLC-5/20C
• PLC-5/40C
• PLC-5/60C
• PLC-5/80C
ControlNet Terminal Ports
ControlNet versions of the PanelView terminal (catalog numbers ending in 15) have a ControlNet communication port and an RS-232 serial port.
• Use the ControlNet port to connect to devices on a ControlNet network.
• Use the RS-232 port to transfer applications between a computer and the terminal or to connect a printer.
For details on connecting to the RS-232 port, see the last section in this chapter.
PanelView 1000 shown
ControlNet
Communications Port
RS-232 Port
Publication 2711-6.1
11-22
Making Terminal Connections
Typical ControlNet Network
Below is a typical ControlNet network with a PanelView terminal installed on a network drop.
PanelView 1000
2711-T10C15 Shown
Personal
Computer
Serial Link
1770-KFC
ControlNet Port
BNC Coaxial Cable
PLC-5/40C
RS-232 Port
Computer for developing
PanelView applications or
Serial Link
Printer
1784-KTC(X) Card to
ControlNet (RSLinx) & WinPFT
ControlLogix 5550
1784-CNB Module
Personal
Computer
1784-KTC(X)
Interface Card
1786-RG6 Cable
PLC-5/80C
Flex I/O
(1784-ACN)
= Taps
= Terminators
Repeater
(1786-RPT)
Publication 2711-6.1
Making Terminal Connections
11-23
Making ControlNet Connections
Use the pinout information below to connect the PanelView to a
ControlNet network.
Important: Follow the ControlNet network layout and design as specified in the ControlNet Cable System Planning and
Installation Manual (Publication 1786-6.2).
Redundant BNC Cable Connectors
NAP Connector
Pin #
1
2
3
6
7
4
5
8
Shell
NAP Signal
Signal Common
No Connection
TX_H
TX_L
RX_L
RX_H
No Connection
Signal Common
Earth Ground
Channel B
Channel A
Pin 1
Publication 2711-6.1
11-24
Making Terminal Connections
NAP and Redundant Cables
ControlNet cables, taps, connectors. Refer to the ControlNet Cable
System Planning and Installation manual (Publication 1786-6.2.1) for descriptions of these components. For information on purchasing these items, refer to the Allen-Bradley ControlNet Cable System
Component List (Publication AG-2.2).
Item
RG-6 quad-shield
Coax repeater
Coax taps
Network access cable
Coax tool kit
Segment terminators
BNC connectors
Catalog Number
1786-RG6
1786-RPT, -RPTD
1786-TPR, -TPS, -TPYR, -TPYS
1786-CP
1786-CTK
1786-XT
1786-BNC, -BNCJ, -BNCP, -BNCJ1
Important: Do not connect to a network using both the redundant cable BNC connector and the Network Access Port
(NAP).
Publication 2711-6.1
DeviceNet Terminal Connections
Making Terminal Connections
11-25
This section describes connections for the DeviceNet PanelView terminals including:
• DeviceNet connectors
• typical DeviceNet network
DeviceNet Terminal Ports
The DeviceNet versions of the PanelView terminals (catalog numbers ending in 10) have a DeviceNet port and an RS-232 serial port.
• Use the DeviceNet port to connect to devices on a DeviceNet network.
• Use the RS-232 port to transfer applications between a computer and the terminal or to connect a printer.
For details on connecting to the RS-232 port, see the last section in this chapter.
PanelView 1000 shown
5 1
DeviceNet Port RS-232 Port
Making DeviceNet Connections
Use one of the cables below to connect the DeviceNet version of the
PanelView terminal to a DeviceNet network.
Cable
DeviceNet Cable, 50 meters (164 feet)
DeviceNet Cable, 100 meters (328 feet)
DeviceNet Cable, 150 meters (492 feet)
Publication No.
1485C-P1A50
1485C-P1A150
1485C-P1A300
Important: Refer to DeviceNet Cable System Planning and
Installation manual (Publication 1485-6.7.1) for network layout and design information
DeviceNet
Terminal Block
1
Terminal
3
4
5
1
2
5
Signal
COM
CAN_L
SHIELD
CAN_H
VDC+
Function
Common
Signal Low
Shield
Signal High
Power Supply
Color
Black
Blue
Uninsulated
White
Red
Publication 2711-6.1
11-26
Making Terminal Connections
DeviceNet
Scanner Module
(Catalog No. 1747-SDN)
Typical DeviceNet Network
Below is a typical DeviceNet network with PanelView terminals installed on 2 of the network drops.
A DeviceNet network requires a 24V dc power supply. DeviceNet power consumption is 24mA - 90mA @24V dc. The PanelView terminal does not receive its power from the network.
PLC-5
SLC 5/04 or
PanelView
DeviceNet
Scanner Module
(Catalog No. 1771-SDN)
PanelView
DeviceNet Port
DeviceNet Port
Serial Link
RS-232 Port
Computer for developing
PanelView applications
1770-KFD
Module
Download/
Upload
RediSTATION
Drive
SM
C
Smart Motor Controller
Publication 2711-6.1
DF1 Terminal Connections
Making Terminal Connections
11-27
This section describes connections for the DF1 versions of the
PanelView terminal including:
• compatible controllers
• DF1 terminal ports
• connecting to a controller (point-to-point)
• using a modem
• connecting to a DeviceNet network
Compatible Controllers
The DF1 terminals support full duplex communications with the following controllers.
• SLC, PLC or MicroLogix 1000 via 1761-Net DNI module
• SLC 5/03, 5/04, or 5/05E (Ethernet version) via Channel 0/DF1 port
• PLC-5/10, 5/12, 5/15, or 5/25 via bridge such as the 1770-KF2, or
1785-KE
• PLC-5/11, 5/20, 5/26, 5/40, 5/46, 5/60, 5/80 via Channel 0/DF1 port
• Ethernet versions of the PLC-5/20E, 5/40E, 5/80E, SLC 5/05E via Channel 0/DF1 port
• ControlNet versions of the PLC-5/20C, 5/40C, 5/60C, 5/80C via
Channel 0/DF1 port
DF1 Terminal Ports
The DF1 versions of the PanelView terminals have a DF1 (Full
Duplex) communications port and an RS-232 serial port.
• Use the DF1 port to communicate with a logic controller using
DF1 full duplex communications.
• Use the RS-232 serial port to transfer applications between a computer and the terminal or to connect a printer. For connection details, see the last section in this chapter.
PanelView 1000 shown
DF1 Port
RS-232 File Transfer/Printer Port
Publication 2711-6.1
11-28
Making Terminal Connections
DF1/RS-232 Port Connector
The DF1 port on the PanelView terminal is a 9-pin, male, RS-232 connector. The table below shows the pinout descriptions for this port and how these pins map to the DF1 ports on the controllers.
7
8
5
6
9
DF1 Port
9-pin DCE
1
2
3
4
Signal
RXD
TXD
DTR
SG
DSR
RTS
CTS
Signal
SLC
9-pin
PLC
25-pin
RXD
TXD
DTR
SG
DSR
RTS
CTS
6
7
8
4
5
2
3
6
4
5
20
7
3
2
MicroLogix/
DNI 8-pin DIN
4
7
2
The maximum cable length for DF1/full duplex communications is
15.24 meters (50 feet).
Connecting to a MicroLogix 1000
The following shows a point-to-point connection between the DF1 port of the PanelView terminal and a MicroLogix 1000.
PanelView
AIC+
1761-NET-AIC
DF1 Port
1761-CBL-HM02
MicroLogix 1000
DF1 Port
2711-NC13, -NC14 Cable
The 1761-NET-AIC is used only with the MicroLogix and eliminates grounding level differences between the controller and PanelView.
Connecting to an SLC or PLC
The following shows a point-to-point connection between the DF1 port of the PanelView terminal and an SLC or PLC controller.
PanelView
SLC 5/03, 5/04, 5/05
DF1 Port
2711-NC13, -NC14 Cable DF1 Port
PLC 5
2711-NC13, -NC14 Cable
9 to 25-Pin
Adapter
DF1 Port
Use an optical isolator or equivalent when grounding level differences exist between the controller or modem and the PanelView.
Publication 2711-6.1
Making Terminal Connections
11-29
Using a Modem
Wire or radio modem communications is possible between a DF1 terminal and controller. Each modem must support full duplex communications. Refer to your modem user manual for details on settings and configuration.
PanelView
Optical Isolator
DF1 Port
Controller
Modem
Modem
Connecting to a DeviceNet Network
The following illustration shows a DF1 PanelView terminal connected to a single controller (MicroLogix, SLC or PLC) in a
DeviceNet network.
DF1 PanelView
DF1 port
Null Modem Cable
MicroLogix 1000
1761-NET DNI Module
1761-CBL-PM02
1761-NET DNI Module
1761-CBL-HM02
DeviceNet
DF1 or
SLC 5/03, 5/04, 5/05
1761-CBL-PM02
DF1
24V dc Power Supply
2755-PW46 or
PLC 5/40C
The SLC or PLC requires the PM02 cable.
Only a single processor can be connected.
DF1
Constructing a Null Modem Cable
To construct a null modem cable, refer to the following pinout:
9-pin
3
1
4
2
5
6
8
7
25-pin
3
2
7
8
20
6
5
4
9-pin
3
1
4
2
5
6
8
7
Publication 2711-6.1
11-30
Making Terminal Connections
Connecting a Computer or Printer to the Terminal
Most of the PanelView terminals have an RS-232 serial port to:
• download/upload applications over a serial link
• and/or connect a printer that supports the IBM enhanced character set
The illustration below shows how to make these connections.
Communication parameters for the RS-232 port are set on the Printer
Setup screen of the Configuration Mode menu.
Computer
PanelView 1000 DH+ Terminal
RS-232 Port
PanelView 550 DH+ Terminal
RS-232 Port
7
8
5
6
9
3
4
1
2
Available Cables
2711-NC13
5 m (16.4 ft)
2711-NC14 10 m (32.7 ft)
2706-NC13 3 m (10 ft)
6
7
8
9
3
4
5
1
2
9-pin to 25-pin Adapter
(if required)
Printer
RS-232 Port
PV550 Printer Port (DCE)
9-pin male
COM
7
8
9
5
6
3
4
PV600/900/1000/1400 Printer Port (DCE)
9-pin male
1
2
NC
RXD or TR1 (Data Receive)
TXD or TX1 (Data Transmit)
NC
COM
DSR (pulled high to +12V)
RTS or RX2 (Data Receive)
CTS or TX2 (Data Transmit)
NC
Upload/Download or Printer Cable without Hardware Handshaking
PV550 Printer Port (DCE)
9-pin male
2
RXD or RX1 (Data Receive)
3 TXD or TX1 (Data Transmit)
5 COM
Printer/Computer Port (DTE)
9-pin 25-pin
2
3
5
3
2
7
RXD (Data Receive)
TXD (Data Transmit)
TXD COM
Printer/Computer Port (DTE)
9-pin female
1
2
3
DCD
RXD (Data Receive)
TXD (Data Transmit)
6
7
4
5
DTR
COM
DSR
8
9
RTS
CTS
NC
Publication 2711-6.1
Chapter
12
Chapter Objectives
Equipment Required
Using the Troubleshooting Chart
Troubleshooting and Maintenance
This chapter tells how to isolate and correct common operating problems and perform routine maintenance tasks.
• equipment required
• using troubleshooting chart
• LED indicators
• cleaning display window
• replacing clock module
• replacing backlight
Other than verifying that the correct power source is connected to the terminal (use a voltmeter), no electronic diagnostic equipment is required for troubleshooting.
The following pages provide a troubleshooting chart for the terminal.
This chart lists the most common operating problems, causes, and steps to correct them.
!
ATTENTION: The PanelView terminals contain hazardous voltages. Do not insert objects or let objects fall into the terminal through ventilation slots. Always disconnect power when checking wiring connections.
Failure to take adequate precautions may result in electrical shock.
Publication 2711-6.1
12-2
Troubleshooting and Maintenance
Problem
Terminal does not power up.
No communications with SLC or PLC controller.
No communications with PLC but COMM
LED is green.
No communications with computer.
Troubleshooting Chart
Probable Cause(s)
Improper connection to power source.
1. Communications (COMM) fault.
2. Baud rates not set properly.
3. Controller is not in run mode.
4. Terminal node and maximum node numbers are not set correctly.
5. Controller fault.
Clock Module Battery
Low message is displayed.
Cannot transfer application from memory card.
Clock module needs replacing.
1. Memory card is not properly installed.
2. Application is too large for terminal memory.
3. Data checksum is incorrect.
4. Invalid file format.
Corrective Action(s)
Verify correct voltage at power terminals on the back of the terminal.
1. Check status of COMM LED.
Verify cable connections using cable diagrams in Chapters 11.
2. Verify that terminal and controller are set at the same baud rate.
3. Place controller in run mode.
4. Verify node number settings.
5. Refer to controller user manual.
1. Verify address of the controller.
2. Change setting of the inhibit bit.
1. PanelView is trying to communicate with a controller at a different address.
2. The inhibit bit is set as the default on the Channel Status Screen in the PLC.
1. Communications (COMM) fault.
2. No SLC, network, or power supply connection at terminal’s DH-485 port.
3. Baud rates not set correctly.
4. Terminal node and maximum node numbers are not set correctly.
5. Computer fault.
6. Communication driver not properly loaded.
7. Printer port is enabled.
1. Check status of COMM LED.
Verify cable connections using cable diagrams in Chapter 10.
2. Personal Computer Interface Converter (PIC) receives power from
DH-485 connection. Verify that the terminal is connected to an SLC, network, or wallmount power supply as shown in Chapter 11.
3. Verify that terminal and computer are set at the correct baud rate.
4. Verify node number settings.
5. Refer to user manual for computer.
6. Refer to RSLinx online help or manual.
7. Disable printing on the Printer
Setup screen of the Configuration
Mode menu.
Replace clock module as described in instructions provided with clock module kit.
1. Verify correct installation.
2. Reduce size of application file.
3. Check that memory card is properly seated. Application may be corrupt.
4. Verify file format (.PVA) being transferred.
Publication 2711-6.1
Troubleshooting and Maintenance
12-3
Problem
Cannot transfer application to memory card.
Probable Cause(s)
1. Memory card is not properly installed.
2. Memory card is write protected.
1
3. File currently exists on memory card.
1
4. Application file is too large, not enough space on memory card.
5. Invalid memory card format.
1
6. Data checksum is incorrect.
7. Application does not exist.
1
Corrective Action(s)
1. Verify correct installation.
2. Change memory card protection switch.
3. Erase and reformat card.
4. Reduce size of application file or erase/format memory card.
5. Replace or reformat memory card. If problem continues, try another card.
6. Check that card is installed correctly.
If problem continues, try another card.
7. Check the Terminal Info screen to verify that an application exists.
Screen objects do not function.
1
Communications problem.
Check status of COMM LED.
See problem ’No communications with
SLC or PLC controller’ for more information.
1. Download application and try again.
2. Download new application.
Application file name appears as ******* on Terminal Info screen.
Area on color screen appears dark.
Screen objects are not visible.
1. Application is invalid.
2. Application is unusable because of error.
One of the backlight tubes has burnt out.
1. Correct power is not applied.
2. Contrast or intensity is not set correctly.
3. Terminal is in screen saver mode.
4. PV550 backlight lamp is not on.
5. Terminal’s backlight is burnt out.
Replace color backlight.
1. Verify power connections.
2. Access Screen Setup on the Configuration Mode menu and adjust the contrast. On keypad terminals, press the left and right arrow keys simultaneously, then press [F9] or
[F15].
3. Access Screen Setup on the Configuration Mode menu to see if terminal is set for screen saver mode.
4. Access Screen Setup on the Configuration Mode menu and turn on backlight.
5. Replace backlight.
Values do not update on display but appear as asterisks
****
1. Terminal is not communicating with controller.
2. Value is invalid or exceeds the field width defined for the object.
1. Check status of COMM LED.
Refer to problem ’No communication with SLC or PLC controller’ for more details.
2. Change the field width for the object.
1
Terminal displays a warning message with instructions if these errors occur.
Publication 2711-6.1
12-4
Troubleshooting and Maintenance
LED Indicators
Use the COMM and Fault LED indicators to isolate operating problems. The illustration below shows the location of these indicators.
COMM LED
Fault LED
COMM LED
Fault LED
PV550 Back View
PV900 Back View
PV600/PV1000 is similar
DH-485 and DH+ LED Indications
LED
Comm
Fault
1
State
On (steady green)
Off (power applied)
Blinking
Off
On (steady red)
Flashing
Indicates
Normal operating state (no communication faults).
Good hardware connection.
Fault detected.
• Make sure controller is run mode
• Verify baud settings of terminal and controller
• Verify proper terminal to controller connections
No communications established
Normal operating state
Fault detected. Cycle power to the terminal. If the fault still exists, the terminal requires servicing.
Hardware is functioning but no application is loaded or the current application is corrupt.
1
Comm LED stays on until powerup self-tests are complete.
Remote I/O LED Indications
LED
Comm
Fault
1
Off
State
On (steady green)
Off (power applied)
Blinking
On (steady red)
Flashing
Indicates
Normal operating state (no communication faults)
Communications not functioning
• Verify that baud rate and rack settings match the PLC settings
• Verify proper terminal to controller connections
• Verify that the PLC enables Remote I/O communications
No communications established. PLC is in program mode.
Normal operating state
Fault detected. Cycle power to the terminal. If the fault still exists, the terminal requires servicing.
Hardware is functioning but no application is loaded or the current application is corrupt.
1
Comm LED stays on until powerup self-tests are complete
Publication 2711-6.1
Cleaning the Display Window
Replacing the Clock Module
Replacing the Backlight
Troubleshooting and Maintenance
12-5
To clean the display window:
ATTENTION: Use of abrasive cleansers or solvents may damage the window. Do not scrub or use brushes.
!
1. Disconnect power from the terminal at the power source.
2. Use a clean sponge or a soft cloth to clean the display with a mild soap or detergent.
3. Dry the display with a chamois or moist cellulose sponge to avoid water spots.
Removing Paint and Grease
Remove fresh paint splashes and grease before drying by rubbing lightly with isoproply alcohol (70% concentration). Afterward, provide a final wash using a mild soap or detergent solution. Rinse with clean water.
Equipment Hose Downs
Be aware that screen objects on touch cell terminals may activate during equipment hose downs.
!
ATTENTION:
Because touch terminals have sensitive touch cell regions, it is possible for screen objects to activate during equipment hose downs.
The Real-Time Clock (RTC) module contains a lithium battery used only by the real-time clock. The battery is not used for application backup or input retention. The clock module has a typical life expectancy of 7 years.
The clock module replacement kits for the PanelView terminals are listed in Chapter 1 under Replacement Parts. Replacement instructions are provided with the kits.
!
ATTENTION: The clock module contains lithium.
Do not attempt to dispose of the module in a fire or incinerator. Doing so may cause the clock module to explode. Follow disposal regulations in your area for lithium battery disposal.
Replacement backlights are available for the PanelView terminals.
See Replacement Parts in Chapter 1 for the catalog numbers.
Replacement instructions are provided with the kits.
Publication 2711-6.1
12-6
Troubleshooting and Maintenance
Publication 2711-6.1
PanelView 300 Terminals
Appendix
A
Specifications
Electrical
DC Power
Supply Voltage Limits
Power Consumption
Mechanical
Enclosure
LED Indicators
COMM
Fault
Weight
Dimensions
Installed Depth
18 to 32V dc (24V dc nominal)
18 Watts, max. (0.75A @ 24V dc) mm
Inches
NEMA Type 12/13, 4X (Indoor use only), IP54, IP65
Green
Red
673 grams (1.48 lbs)
197 (H) x 140 (W) x 82 (D)
7.76 (H) x 5.53 (W) x 3.21 (D)
69mm (2.73 inches)
122.4 mm (4.82 inches) with memory card retainer
216 mm (8.5 inches) with memory card retainer and clearance to insert and remove memory card
Display
Type
Size
Pixels
Liquid Crystal Display (LCD) with integral LED backlight (100,000 hour life)
73 mm (w) x 42 mm (h)
2.87 in. (w) x 1.67 in. (h)
128 x 64
Terminal Memory
Total Application Flash Memory
240K bytes (application screens)
Environment
Operating Temperature
Storage Temperature
Relative Humidity (non-condensing)
Heat Dissipation
Impulse Shock (operating/non-operating)
Vibration (operating)
0 to 55
°
C (32 to 131
°
F)
-25 to 85
°
C (-4 to 188
°
F)
5 to 95% at 0 to 55
°
C (32 to 131
°
F)
18 Watts (69 BTU/HR)
15G/30G
2G up to 2,000 Hz
Publication 2711-6.1
A-2
Specifications
PanelView 550 Terminals
Character Sizes (Pixel size = 0.48 x 0.48 mm)
Size in Pixels
(width x height)
4 x 6
6 x 8
6 x 16
6 x 24
12 x 8
12 x 16
12 x 24
18 x 8
18 x 16
18 x 24
Characters/Row
10
10
6
6
6
31
20
20
20
10
Maximum Rows
3
2
7
3
2
3
2
7
10
7
Dimensions in mm
Width x Height
1.9 x 2.9
2.9 x 3.8
2.9 x 7.7
2.9 x 11.5
5.8 x 3.8
5.8 x 7.7
5.8 x 11.5
8.6 x 3.8
8.6 x 7.7
8.6 x 11.5
Electrical
AC Power
Supply Voltage Limits
Power Consumption
DC Power
Supply Voltage Limits
Power Consumption
Supply Voltage Limits (touch screen only)
Power Consumption (touch screen only)
85 to 264V ac, 47 to 63 Hz
45 VA maximum
18 to 30V dc (24V dc nominal)
18 Watts, max. (0.75A @ 24V dc)
18 to 32V dc (24V dc nominal)
18 Watts, max. (0.75A @ 24V dc)
Mechanical
Enclosure
LED Indicators
COMM
Fault
Weight
Keypad, Keypad & Touch
Touch Screen
Dimensions- Keypad, Keypad & Touch mm
Inches
Dimensions- Touch Screen mm inches
Installed Depth- Keypad, Keypad & Touch
Installed Depth- Touch Screen
NEMA Type 12/13, 4X (Indoor use only), IP54, IP65
Green
Red
1.2 kg (2.7 lbs)
.93 kg (2.1 lbs)
167 (H) x 266 (W) x 106 (D)
6.57 (H) x 10.47 (W) x 4.17 (D)
152 (H) x 185 (W) x 82 (D)
6.00 (H) x 7.28 (W) x 3.20 (D)
86 mm (3.39 inches)
118 mm (4.64 inches) with memory card retainer
207 mm (8.15 inches) with memory card retainer and clearance to insert and remove memory card
64 mm (2.54 inches)
109 mm (4.30 inches) with memory card retainer
188 mm (7.40 inches) with memory card retainer and clearance to insert and remove memory card
Publication 2711-6.1
Specifications
A-3
Display
Type
Size
Pixels
Touch Cells
Touch Cell Size
Terminal Memory
PV550 ( Series E or later) or
PV550T (Series A or later)
Total Application Flash Memory
PV550 (Prior to Series E)
Total Application Flash Memory
Liquid Crystal Display (LCD)
120 x 60 mm (4.75 x 2.38 in.)
256 x 128
128 (16 columns x 8 rows)
16 x 16 pixels
240K bytes (application screens)
112K bytes (application screens)
Environment
Operating Temperature
Storage Temperature
Relative Humidity (non-condensing)
Heat Dissipation
Impulse Shock (operating/non-operating)
Vibration (operating)
0 to 55
°
C (32 to 131
°
F)
-20 to 70
°
C (-4 to 158
°
F)
5 to 95% at 0 to 30
°
C (32 to 86
°
F)
5 to 75% at 31 to 40
°
C (88 to 104
°
F)
5 to 50% at 41 to 55
°
C (106 to 131
°
F)
20 Watts (69 BTU/HR) for AC Power or DC Power
30G/50G
2G up to 2,000 Hz
Character Sizes (Pixel size = 0.47 x 0.47 mm)
Size in Pixels
(width x height)
6 x 8
6 x 16
6 x 24
12 x 8
12 x 16
12 x 24
18 x 8
18 x 16
18 x 24
Characters/Row
20
13
40
20
13
40
20
13
40
Maximum Rows
5
5
8
8
5
16
16
16
8
Dimensions in mm
Width x Height
2.2 x 3.2
3.8 x 5.6
3.8 x 8.4
7.6 x 2.8
7.6 x 5.6
7.6 x 8.4
11.2 x 2.8
11.2 x 5.6
11.2 x 8.4
Publication 2711-6.1
A-4
Specifications
PanelView 600 Color Terminal
Keypad & Touch
Electrical
AC Power
Supply Voltage Limits
Power Consumption
DC Power
Supply Voltage Limits
Power Consumption
Mechanical
Enclosure
LED Indicators
COMM
Fault
Weight
Dimensions
Installed Depth
85 to 264V ac, 43 to 63 Hz
60 VA maximum
18 to 32V dc (24V dc nominal)
34 Watts max. (1.4A @ 24V dc) mm inches
NEMA Type 12/13, 4X (Indoor use only), IP54, IP65
Green
Red
2 kg (4.4 lbs)
192 (H) x 290 (W) x 116 (D)
7.55 (H) x 11.40 (W) x 4.57 (D)
99 mm (3.89 inches)
131 mm (5.14 inches) with memory card retainer
220 mm (8.65 inches) with memory card retainer and clearance to insert and remove memory card
Display
Type
Size
Pixels
Touch Cells
Touch Cell Size
Active Matrix Thin-Film Resistor (TFT) with Cold
Cathode Fluorescent (CCF) Backlight
115 x 86 mm (4.54 x 3.4 in.)
320 x 234
128 (16 columns x 8 rows)
20 x 29 pixels
Terminal Memory
Total Application Flash Memory 240K bytes (application screens)
Environment
Operating Temperature
Storage Temperature
Relative Humidity (non-condensing)
Heat Dissipation
Impulse Shock (operating/non-operating)
Vibration (operating)
0 to 55
°
C (32 to 131
°
F)
-25 to 70
°
C (-13 to 158
°
F)
5 to 95% at 0 to 55
°
C (32 to 131
°
F)
32 Watts (107 BTU/HR) for AC or DC Power
30G/50G
2G up to 2,000 Hz
Publication 2711-6.1
Specifications
A-5
Character Sizes (Pixel size = 0.36 x 0.37 mm)
Size in Pixels
(width x height)
6 x 9
8 x 16
8 x 24
16 x 24
24 x 32
32x 40
Characters/Row
52
39
39
19
13
9
Maximum Rows
9
9
7
25
14
5
Dimensions in mm
Width x Height
2.9 x 5.9
2.9 x 5.9
2.9 x 8.9
5.8 x 8.9
8.6 x 11.8
11.5 x 14.8
PanelView 600 Color Terminals
Touch Only
Electrical
DC Power
Supply Voltage Limits
Power Consumption
Mechanical
Enclosure
LED Indicators
COMM
Fault
Weight
Dimensions
Installed Depth
18 to 32V dc (24V dc nominal)
17 Watts max. (0.71A @ 24V dc) mm inches
NEMA Type 12/13, 4X (Indoor use only), IP54, IP65
Green
Red
1 kg (2.3 lbs)
152 (H) x 185 (W) x 96 (D)
6.00 (H) x 7.28 (W) x 3.80 (D)
79 mm (3.12 inches)
132 mm (5.21 inches) with memory card retainer
211 mm (8.30 inches) with memory card retainer and clearance to insert and remove memory card
Display
Type
Size
Pixels
Touch Cells
Touch Cell Size
Terminal Memory
Total Application Flash Memory
Passive Matrix LCD with Cold Cathode Fluorescent
(CCF) Backlight
115 x 87 mm (4.54 x 3.43 in.)
320 x 240
128 (16 columns x 8 rows)
20 x 30 pixels
240K bytes (application screens)
Publication 2711-6.1
A-6
Specifications
Environment
Operating Temperature
Storage Temperature
Relative Humidity (non-condensing)
Heat Dissipation
Impulse Shock (operating/non-operating)
Vibration (operating)
0 to 50
°
C (32 to 122
°
F)
-25 to 70
°
C (-13 to 158
°
F)
5 to 95% at 0 to 40
°
C (32 to 104
°
F)
17 Watts (57 BTU/HR)
15G/30G
2G up to 2,000 Hz
Character Sizes (Pixel size = 0.35 x 0.35 mm)
Size in Pixels
(width x height)
6 x 9
8 x 16
8 x 24
16 x 24
24 x 32
32x 40
Characters/Row
52
39
39
19
13
9
Maximum Rows
9
9
25
14
7
5
Dimensions in mm
Width x Height
2.1 x 3.1
2.8 x 5.6
2.8 x 8.4
5.6 x 8.4
8.4 x 11.1
11.1 x 13.9
Publication 2711-6.1
Specifications
A-7
PanelView 900 Monochrome and
Color Terminals
Electrical
AC Power - PV900M and PV900C
Supply Voltage Limits
Power Consumption
DC Power - PV900M
Supply Voltage Limits
Power Consumption
DC Power - PV900C
Supply Voltage Limits
Power Consumption
85 to 264V ac, 47 to 63 Hz
110 VA maximum
18 to 30 V dc (24V dc nominal)
58 Watts max. (2.5A @ 24V dc)
18 to 32 V dc (24V dc nominal)
50 Watts max. (2.1A @ 24V dc)
Mechanical
Enclosure
LED Indicators
COMM
Fault
Weight - PV900M
Keypad
Touch Screen
Weight - PV900C
Keypad
Touch Screen
Dimensions - PV900M/900C Keypad mm inches
Dimensions - PV900M/900C Touch Screen mm inches
Installed Depth - PV900M
Installed Depth - PV900C
NEMA Type 12/13, 4X (Indoor use only) IP54, IP65
Green
Red
3.14 kg (4.4 lbs)
2.91 kg (6.4 lbs)
3.18 kg (7.0 lbs)
2.95 kg (6.5 lbs)
249 (H) x 406 (W) x 112 (D)
9.80 (H) x 15.97 (W) x 4.40 (D)
249 (H) x 336 (W) x 112 (D)
9.80 (H) x 13.24 (W) x 4.40 (D)
97 mm (3.81 inches)
129 mm (5.06 inches) with memory card retainer
220 mm (8.65 inches) with memory card retainer and clearance to insert and remove memory card
99 mm (3.89 inches)
131 mm (5.14 inches) with memory card retainer
222 mm (8.73 inches) with memory card retainer and clearance to insert and remove memory card
Publication 2711-6.1
A-8
Specifications
Display
PV900M
Type
Size
Pixels
Touch Cells
Touch Cell Size
PV900C
Type
Size
Pixels
Touch Cells
Touch Cell Size
AC Gas Plasma
210 x 131 mm (8.27 x 5.17 in.)
640 x 400
384 (24 columns x 16 rows)
26 x 25 pixels
Active Matrix Thin-Film Resistor (TFT) with Cold
Cathode Fluorescent (CCF) Backlight
171 x 130 mm (6.73 x 5.12 in.)
640 x 480
384 (24 columns x 16 rows)
26 x 30 pixels
Terminal Memory
PV900M (prior to Series E)
Total Application Flash Memory
PV900M (Series E, firmware 3.0 or later),
PV900C
Total Application Flash Memory
240K bytes (application screens)
1008K bytes (application screens)
Environment
PV900M
Operating Temperature
Storage Temperature
Relative Humidity (non-condensing)
Heat Dissipation
Impulse Shock (operating/non-operating)
Vibration (operating)
PV900C
Operating Temperature
Storage Temperature
Relative Humidity (non-condensing)
Heat Dissipation
Impulse Shock (operating/non-operating)
Vibration (operating)
0 to 55
°
C (32 to 131
°
F)
-25 to 70
°
C (-13 to 158
°
F)
5 to 85% at 0 to 30
°
C (32 to 86
°
F)
50 Watts (165 BTU/HR) for AC Power or
DC Power
15G/30G
1G up to 2,000 Hz
0 to 55
°
C (32 to 131
°
F)
-25 to 70
°
C (-13 to 158
°
F)
5 to 95% at 0 to 55
°
C (32 to 131
°
F)
39 Watts (133 BTU/HR)
15G/30G
1G up to 2,000 Hz
Publication 2711-6.1
Specifications
A-9
Character Sizes - PV900M (Pixel size = 0.33 x 0.33 mm)
Size in Pixels
(width x height)
Characters/Row Maximum Rows
8 x 16
8 x 24
16 x 24
24 x 32
32x 40
79
79
39
26
19
24
16
16
12
9
Character Sizes - PV900C (Pixel size = 0.27 x 0.27 mm)
Size in Pixels
(width x height)
8 x 16
8 x 24
16 x 24
24 x 32
32x 40
Characters/Row
79
79
39
26
19
Maximum Rows
24
19
19
14
11
Dimensions in mm
Width x Height
2.6 x 5.3
2.6 x 7.9
5.3 x 7.9
7.9 x 10.6
10.6 x 13.2
Dimensions in mm
Width x Height
2.2 x 4.3
2.2 x 6.5
4.3 x 6.5
6.5 x 8.6
8.6 x 10.8
Publication 2711-6.1
A-10
Specifications
PanelView 1000 Grayscale and
Color Terminals
Electrical
AC Power - PV1000G and PV1000C
Supply Voltage Limits
Power Consumption
DC Power - PV1000G
Supply Voltage Limits
Power Consumption
DC Power - PV1000C
Supply Voltage Limits
Power Consumption
85 to 264V ac, 47 to 63 Hz
100 VA maximum
18 to 32 V dc (24V dc nominal)
40 Watts max. (1.7A @ 24V dc)
18 to 32 V dc (24V dc nominal)
50 Watts max. (2.1A @ 24V dc)
Mechanical
Enclosure
LED Indicators
COMM
Fault
Weight - PV1000G
Keypad
Touch
Weight - PV1000C
Keypad
Touch Screen
Dimensions-PV1000G/1000C Keypad mm inches
Dimensions - PV1000G/1000C Touch Screen mm inches
Installed Depth - PV1000G
Installed Depth - PV1000C
NEMA Type 12/13, 4X (Indoor use only) IP54, IP65
Green
Red
3.27 kg (7.2 lbs)
3.18 kg (7.0 lbs)
3.72 kg (8.2 lbs)
3.58 kg (7.9 lbs)
282 (H) x 423 (W) x 112 (D)
11.11 (H) x 16.64 (W) x 4.40 (D)
282 (H) x 370 (W) x 112 (D)
11.11 (H) x 14.58 (W) x 4.40 (D)
97 mm (3.81 inches)
129 mm (5.06 inches) with memory card retainer
220 mm (8.65 inches) with memory card retainer and clearance to insert and remove memory card
99 mm (3.89 inches)
131 mm (5.14 inches) with memory card retainer
222 mm (8.73 inches) with memory card retainer and clearance to insert and remove memory card
Terminal Memory
Total Application Flash Memory 1008K bytes (application screens)
Publication 2711-6.1
Specifications
A-11
Display
PV1000G
Type
Size
Pixels
Touch Cells
Touch Cell Size
PV1000C
Type
Size
Pixels
Touch Cells
Touch Cell Size
Electroluminescent
211 x 158 mm (8.3 x 6.2 in.)
640 x 480
384 (24 columns x 16 rows)
26 x 30 pixels
Active Matrix Thin-Film Resistor (TFT) with Cold
Cathode Fluorescent (CCF) Backlight
211 x 158 mm (8.3 x 6.2 in.)
640 x 480
384 (24 columns x 16 rows)
26 x 30 pixels
Environment
Operating Temperature
Storage Temperature
Relative Humidity (non-condensing)
Heat Dissipation
0 to 55
°
C (32 to 131
°
F)
-25 to 70
°
C (-13 to 158
°
F)
5 to 95% at 0 to 55
°
C (32 to 131
°
F)
39 Watts (132 BTU/HR) for Grayscale and Color
Impulse Shock (operating/non-operating) 15G/30G
Vibration (operating) 2G up to 2,000 Hz
Character Sizes - PV1000G and PV1000C (Pixel size = 0.33 x 0.33 mm)
Size in Pixels
(width x height)
8 x 16
8 x 24
16 x 24
24 x 32
32x 40
Characters/Row
79
79
39
26
19
Maximum Rows
24
19
19
14
11
Dimensions in mm
Width x Height
2.2 x 5.3
2.6 x 7.9
5.3 x 7.9
7.9 x 10.6
10.6 x 13.2
Publication 2711-6.1
A-12
Specifications
PanelView 1400 Color Terminals
Electrical
AC Power
Supply Voltage Limits
Power Consumption
Terminal Memory
Total Application Flash Memory
85 to 264V ac, 43 to 63 Hz
200 VA maximum
Mechanical
Enclosure
LED Indicators
COMM
Fault
Weight
Keypad
Touch Screen
Dimensions - PV1400 Keypad mm iinches
Dimensions - PV1400 Touch Screen mm inches
Installed Depth
NEMA Type 12/13, 4X (Indoor use only) IP54, IP65
Green
Red
20.3 kg (44.75 lbs)
19.6 kg (43.2 lbs)
355 (H) x 483 (W) x 394 (D)
13.97 (H) x 19.0 (W) x 15.53 (D)
355 (H) x 441 (W) x 394 (D)
13.97 (H) x 17.37 (W) x 15.53 (D)
370 mm (14.58 inches)
400 mm (15.75 inches) with clearance to insert and remove memory card
1008K bytes (application screens)
Display
Type
Size
Pixels
Touch Cells
Touch Cell Size
Color CRT
255 x 191 mm (10.0 x 7.5 in.)
800 x 600
384 (24 columns x 16 rows)
33 x 37 pixels
Environment
Operating Temperature
Storage Temperature
0 to 55
°
C (32 to 131
°
F)
-40 to 85
°
C (-40 to 185
°
F)
5 to 95% at 0 to 55
°
C (32 to 131
°
F) Relative Humidity (non-condensing)
Heat Dissipation 78 Watts (264 BTU/HR)
Impulse Shock (operating/non-operating) 15G/30G
Vibration (operating) 1G up to 2,000 Hz
Publication 2711-6.1
Communications
Specifications
A-13
Character Sizes - PV1400 (Pixel size = 0.32 x 0.32 mm)
Size in Pixels
(width x height)
8 x 20
16 x 24
24 x 32
32 x 40
32 x 64
Characters/Row
99
49
33
24
24
Maximum Rows
29
24
18
14
9
Dimensions in mm
Width x Height
2.5 x 6.4
5.1 x 7.6
7.6 x 10.2
10.2 x 12.7
10.2 x 20.4
DH-485 Network
Baud Rate
Distance Maximum
DH+ Network
Baud Rate
Distance Maximum
RS-232 or DH-485 Point-to-Point
Baud Rates
Distance Maximum
Remote I/O
Baud Rates
DeviceNet
Baud Rates
ControlNet Network
Baud Rate
Distance Maximum
DF1/Full Duplex Communications
Baud Rate
Distance Maximum
RS-232 Printer Port
Baud Rates
Parity
Data Bits
Stop Bits
Handshaking
1200, 2400, 9600, 19.2K
1219 meters (4,000 feet)
57.6K, 115.2K, 230.4K
3048 meters (10,000 feet)
1200, 2400, 9600, 19.2K
6.1 meters (20 feet)
57.6K, 2,800 meters (10,000 feet)
115.2K, 1,400 meters (5,000 feet)
125K, 250K, 500K
5M
1,000 meters (3,280 feet)
1200, 2400, 4800, 9600, 19.2K
15.24 meters (50 feet)
1200, 2400, 9600, 19.2K
None, Even, Odd
7 or 8
1 or 2
None, Software (XON, XOFF), Hardware
Publication 2711-6.1
A-14
Specifications
Agency Certifications
See Nameplate label on each terminal for certifications.
300 550 600 900M 900C 1000G 1000C
Emissions (Class B: Light Industrial) EN50081- 1:1992
x
1 x
1
Emissions (Class A: Industrial)
EN50081-2:1993
Immunity (Industrial)
EN50082-2:1995
Programmable Controllers
Equipment Requirements and
Tests) EN61131 2:1995
Low Voltage Directive
(Safety Sections of EN61131-2)
UL508
UL1604 Class 1, Div 2,
Groups A, B, C, D, T4
UL2279 (IEC79-15) Class 1,
Zone 2, Groups IIC, T4
DEMKO prEN5002 1 Ex Na
Group IIC, T4
CSA 22.2, No. 142
x x x x x x x x x x x x
2,4 x x x x x x x x
5 x x x x x x
3 x x x x x x x x x x x x x x x x x x x x x x x x x x x
CSA 22.2, No. 213 Class 1,
Div 2, Groups A, B, C, D, T4
x x
2,4 x x
3 x x x
1
DeviceNet PanelView terminals are Class A for Emissions
2
PV550 (Series C or later) or PV550 Touch Screen Only (Series A or later)
3
PV900M (Series C or later)
4
All PV550 terminals have a Temperature Code Rating of T2
5
Does not apply to 600 touch screen only terminals
1400 x x x x x x
Publication 2711-6.1
Types of Terminal Messages
Appendix
B
Messages, Codes and Self-Test Numbers
This appendix lists:
• terminal messages and codes that may appear during terminal operation
• description of self-test numbers
Status Messages
Indicate the terminal is performing an operation that may limit access to the terminal, such as an application download or a communication problem. The message disappears when the terminal completes the operation or when the condition is satisfied.
Reminder Messages
Indicate a minor fault or mistake. Reminder messages appear when an invalid operation is attempted, such as entering an out-of-range value.
Pressing any key removes the message.
Warning Messages
Indicate the operation may produce undesirable results. You must respond to warning messages as indicated in the message.
Fault Messages
Indicate the terminal has detected a condition which prevents further operation. The current application will halt. The terminal must be reset (power cycled) to recover from this type of error.
Publication 2711-6.1
B-2
Messages, Codes and Self-Test Numbers
General Terminal Messages
Error Number Terminal Messages Type
200-206, 300,
318-321, 328,
329, 331, 346,
347, 355, 356,
358, 367, 404,
411, 416, 417,
421-425, 447-
449, 457, 459,
700, 1105,
1111, 1113,
1115, 1207-
1211, 2002-
2009, 2016,
2018, 2021,
2028 and
2029
A fault has occurred.
Error = X
Minor Fault or
Terminal Fault
208 Write to logic controller failed
Comm Status
303
304
305
307
308
309-311
312
313
314
Aborted.
File read access error
File write access error
File not supported
Timeout
Data corrupted. Verify file and retry.
Unknown device
File too large
No Card Inserted
Meaning
A minor fault was detected that could impact terminal operation or a terminal fault was detected.
Recommended Action
Press any key to recover from a minor fault. For terminal faults, contact technical support with the error code.
Reminder/File
Transfer Status
Reminder
Reminder
Reminder/File
Transfer Status
Reminder / File
Transfer Status
Reminder/File
Transfer Status
Reminder / File
Transfer Status
Reminder/File
Transfer Status
Reminder
Controller does not accept data from the terminal. Controller is not connected.
The terminal received an abort command during a file transfer.
Error reading the source file from a source device.
Error writing source file.
Check connections (on
Remote I/O units). Verify that controller is in run mode and not busy. Verify that controller data files are not in use by other applications.
Try again.
File is incompatible with the terminal’s firmware.
The terminal was waiting for the partner device in a file transfer, but the terminal timed out before the data or expected reply was received.
The data checksum failed in a file transfer.
Try again. If problem continues, contact technical support.
Try again. If problem continues, contact technical support.
Contact technical support to verify compatibility. File must be a .PVA file.
Check cable connections or data corruption with noise on cable. Verify that the computer was not reset. Try again.
Check electrical and cable connections. Try the file transfer again.
Verify the file type entered. Try again.
Destination or source device is invalid for a read or write application transfer.
File too large to be transferred to the terminal. In a memory card transfer, the card does not have enough space.
You tried to transfer data to/ from a memory card but there is no card in the card slot.
Reduce application size. See
Appendix A for terminal requirements. If copying to a card, check card space.
Install a memory card and try again.
Publication 2711-6.1
Messages, Codes and Self-Test Numbers
B-3
Error Number
315
316
317
323
324
325
326
327
330
332
333
334
340
341
Terminal Message
Unformatted card
Write Protected Card
File exists. Cannot overwrite
No application on PV terminal
Check card status
Unformatted card
No Card Inserted
No files
Write Protected Card
No application on PV terminal
File in use - Request denied
Unexpected card removal. Please disconnect card before removal.
Format erases entire card:
0 or F1 Abort
1 or F2 - Continue
Proceed with download?
0 or F1 -Abort
1 or F2 - Continue
Type
Reminder
Reminder / File
Transfer Status
Reminder/File
Transfer Status
Reminder/File
Transfer Status
Reminder/File
Transfer Status
Reminder
Reminder
Reminder
Reminder / File
Transfer Status
Reminder/File
Transfer Status
Reminder
Reminder / File
Transfer Status
Warning
Warning
Meaning
Memory card is unformatted, contains an unrecognizable format or is corrupt.
A write command to the card failed because the card switch is in the protected mode.
See message 342. This message only occurs when the file cannot be renamed.
You tried to load an application on a memory card but there is no application in the terminal.
Problem formatting the memory card.
Memory card is unformatted, contains an unrecognizable format or is corrupt.
You tried to transfer data to/ from a memory card but there is no card in the card slot.
You tried to transfer a file from the memory card but there are no files on the card.
A write command to the card failed because the card switch is in protected mode.
You tried to load an application on a memory card but there is no application in the terminal.
Attempt to format memory card containing a file used by the application. This usually occurs when an application requires a font file on the memory card.
You removed the memory card during normal operation and did not press the Disconnect button on the Memory Card configuration screen.
Operator pressed [F4] Erase /
Format Card on the Memory
Card configuration screen.
Recommended Action
Reformat the card or replace it with a new card if corrupt. Try again.
Select write mode by changing the switch on the top edge of the card. Try again.
Change the file name or save to a new memory card.
View the Terminal Info screen to see if an application is loaded in the terminal.
Try a new memory card.
Reformat the card or replace it with a new card. Try again.
Install a memory card and try again.
Use memory card containing application (.PVA) files.
Select write mode by changing the switch on the top edge of the card. Try again.
View the Terminal Info screen to see if an application is loaded in the terminal.
Format the memory card on a computer or a PanelView terminal that does not have an application loaded.
Press the Disconnect Card button to close the files on the card. When prompted, remove the card from the slot and then re-insert the card. Enter Configuration Mode and press the
Run Mode button.
Enter appropriate response:
0 or F1 to abort
1 or F2 to continue
You pressed [F2], Restore
From Card on the Memory
Card configuration screen.
Enter appropriate response:
0 or F1 to abort
1 or F2 to continue
Publication 2711-6.1
B-4
Messages, Codes and Self-Test Numbers
Error Number Terminal Message
342 The PVA File exists.
0 or F1 -Abort
1 or F2 - Upload with new PVA filename
361 Value not in range
Type
Reminder / File
Transfer Status
Meaning
You pressed [F3], Save To
Card on the Memory Card configuration screen when the file exists on the card.
Recommended Action
Enter appropriate response:
0 or F1 to abort file.
1 or F2 to upload new PVA
364
365
366
392
393
394
395
396
415
436
Closing Files . . .
Remove card . . .
Card disconnection will require card removal to continue operation.
File not supported
File not supported
File not supported
File not supported
File not supported
Retained memory lost.
Presets were loaded.
Logic Controller has screen control
Reminder
Status
Reminder
Warning
Reminder/File
Transfer Status
Reminder/File
Transfer Status
Reminder/File
Transfer Status
Reminder/File
Transfer Status
Reminder/File
Transfer Status
Reminder
Reminder
Entered value is outside of valid range.
Terminal is preparing for removal of memory card.
You must remove the memory card for the terminal to continues operation.
Attempt to disconnect the memory card.
Enter a value within the valid range.
Wait for files to close before removing memory card.
Remove the memory card.
File is incompatible with the terminal type.
File is incompatible with the communication protocol of the terminal.
File is incompatible with the terminal’s firmware.
File is incompatible with the operator input type (keypad, touch or keypad and touch) of terminal.
File is incompatible with the terminal.
After memory card is disconnected it must be removed from card slot before the terminal will operate.
In PanelBuilder32, select the
Setup tab on the Application
Settings dialog and select the correct terminal type.
In PanelBuilder32, select the
Setup tab on the Application
Settings dialog and make sure the protocol matches your terminal.
In PanelBuilder32, click the
Catalog & Revisions button on the Setup tab on the Application Settings dialog. Select a firmware version that matches your terminal.
In PanelBuilder32, select the
Setup tab on the Application
Settings dialog. Select the type of operator input that matches your terminal.
Download the file to the terminal again. If problem reoccurs, contact technical support.
No action necessary. Terminal reverts to defaults.
The battery backed memory was invalid during startup. The system defaulted to preset values instead of the last states.
You tried to change the application screen but it is configured for controller only access.
No action required, controller will change screens as programmed.
Publication 2711-6.1
Messages, Codes and Self-Test Numbers
B-5
Error Number Terminal Message
1109 Font file unavailable,
Font error = ****
1110
1118
1119
1120
1121
1122
1123
1124
1125
1126
1127
2005
2007 - 2010
2011
2012
2014
No valid application
Access denied.
Access denied.
Security tampering.
No operator selected.
Password change is not allowed.
Password change is not allowed.
New password must be entered before it can be verified.
New and verify passwords differ.
Please verify new password.
Password changed
Application file:
Insufficient RAM
Application file contains errors
Retained memory lost. Presets were loaded.
Application file: Too many retained memory devices
Hardware configuration is corrupted
Type
Minor Fault or
Terminal Fault
Reminder
Status
Status
Status
Status
Reminder
Reminder
Reminder
Status
Reminder
Reminder
Terminal Fault
Terminal Fault
Reminder
Terminal Fault
Terminal Fault
Meaning
You downloaded an application to the PanelView without the appropriate memory card (containing the font file) inserted in the card slot of the terminal.
You tried to run an application that has not been downloaded to the terminal.
Wrong password entered.
Password not recognized
PVA file was corrupted attempt to bypass security was detected
There is no currently selected operator, but a password change has been requested
Password is unchangeable
Recommended Action
From the Memory Card screen, press the Disconnect button to close the files on the card.
Remove the card from the card slot. Locate the card containing the font file or copy the correct font file to a card. Insert the correct memory card in the card slot and enter Run mode.
Download application to terminal.
Enter a valid password.
Enter a valid password.
New application file must be downloaded to the terminal.
Select the operator requiring the new password.
Operator cannot change password
New pass words must be entered twice.
Password cannot be changed at the current level of security.
Current operator does not have access for password changes.
Enter the new password again to verify that it was entered correctly.
Enter the same password for
New and Verify.
Enter the new password again.
The same password was not entered for verification.
New pass words must be entered twice.
Password change is effective.
Application file may be too large.
Application contains incompatible data.
The battery backed memory was invalid during startup. The system defaulted to preset values instead of the last states.
The battery-backed RAM is too full to hold all devices requiring presets.
The terminal hardware configuration is corrupt.
You must use new password for security access.
Try again. If possible, reduce the size of the application.
Check application and try again.
No action necessary. Terminal reverts to defaults.
Reduce the number of control objects. Use global objects.
Contact technical support.
Publication 2711-6.1
B-6
Messages, Codes and Self-Test Numbers
2030, 2031 Hardware and firmware do not match
Terminal Fault A mismatch exists between the terminal firmware and the terminal hardware.
Verify that the series and revision markings on the back of the terminal are compatible with the firmware.
ControlLogix Terminal Messages
Error Number Terminal Message
634 Write Fail
634 Read Fail
See Terminal Codes for messages below
Type Meaning
Comm Status
Comm Status
ControlLogix Tag or address does not exist or is the wrong data type.
Designated slot does not contain a ControlLogix Processor.
ControlLogix Tag or address does not exist or is the wrong data type.
Designated slot does not contain a ControlLogix Processor.
Recommended Action
Check tag address.
Check for data type mismatch.
Verify ControlLogix slot location.
Check tag address.
Check for data type mismatch.
Verify ControlLogix slot location.
Publication 2711-6.1
Messages, Codes and Self-Test Numbers
DH-485 Terminal Messages
B-7
Error Number Terminal Message
612 No active node(s) found on network
613
615
616
Required network node(s) not found
Duplicate node address
Data errors on the link
Type
Comm Status
Comm Status
Comm Status
Comm Status
Meaning
No other DH-485 devices can be located on the network.
1. If the message is flashing, the terminal is trying to read or write one or more SLC files that are unavailable.
2. The network is active, but
SLCs are not located at the expected nodes. Node and maximum node numbers may not be set correctly.
More than one node was assigned the same address.
Corrupt data packets were detected on DH-485 network.
Recommended Action
Verify that the PanelView terminal and SLC are correctly connected to the system. If the error occurs. again, check the node addresses, baud rates, and maximum node addresses. Reset the terminal.
1. The files do not exist on
SLC. Create files on SLC.
2. Verify that the SLC(s) required by the application are at the expected node addresses with the communication parameters set properly.
Verify all device nodes.
Verify controller addressing and baud rate settings. Check for loose or reversed wiring.
ControlNet Terminal Messages
634 PanelView offline
See Terminal Codes for messages below
Comm Warning PanelView is offline.
Check connections
634
634
634
634
636
Write fail.
Write timeout.
Read fail.
Read timeout.
Initial write failed.
Comm Warning
Comm Warning
Comm Warning
Comm Warning
Reminder
PanelView is communicating with the controller. The data table address does not exist.
PanelView is not communicating with the logic controller.
PanelView is communicating with the controller. The data table address does not exist.
PanelView is not communicating with the controller.
Write to Logic Controller on
Startup was configured and on powerup, the PanelView could not write initial values to a node's data table address.
or
Write to Logic Controller on
Startup was not configured and the PanelView was unable to write a controller. Note: The error is only displayed on the first write attempt.
Check / define data table address in the controller.
Check connections and node configuration in the application.
Check/define data table address in the controller.
Check/define data table address in the controller.
Check/define data table address in the controller.
Check communication connections and node configuration in the application.
Publication 2711-6.1
B-8
Messages, Codes and Self-Test Numbers
Remote I/O Terminal Messages
Error Number
661
662
663
664
665
666
667
Terminal Message
Timeout - No Block
Transfer Writes
Timeout - No Block
Transfer Reads
No PLC communications
PLC in program mode
Timeout - No Block
Transfer Requests
Invalid Rack Configuration
Remote I/O Hardware Failed
Type
Comm Status
Comm Status
Comm Status
Comm Status
Comm Status
Comm Status
Comm Status
Meaning
The PLC is communicating with the terminal, but the PanelView is not receiving BTW requests required by the application.
The PLC is communicating with the terminal, but the PanelView is not receiving BTR requests required by the application.
The PLC is not communicating.
Possible causes are disconnected cable, no power to PLC, incorrect baud rate or rack settings for PLC configuration.
COMM LED is off.
Recommended Action
Check ladder logic for missing
BTW instructions (instructions are not enabled) or addressing errors. Check for logic controller errors.
Check ladder logic for missing
BTR instructions (instructions are not enabled) or addressing errors. Check for logic controller errors.
Check for pulled cables and
PLC power. Check baud rate settings and rack configurations.
Check wiring of connector.
Communication resumes when problem is corrected.
Place the PLC in run mode to resume communication.
The PLC is offline (in Program
Mode). The COMM LED on the
Configuration Mode menu is off.
The PLC is communicating with the terminal, but the PanelView is not receiving BTR or
BTW requests required by the application.
No communications can occur because of an invalid rack configuration.
During startup, the terminal detected a missing, corrupt or nonfunctional Remote I/O card.
The terminal will run but not communicate.
Check ladder logic for missing
BTR or BTW instructions
(instructions are not enabled) or addressing errors. Check for logic controller errors.
Correct the RIO rack configuration.
Contact technical support and provide specific message.
Publication 2711-6.1
Messages, Codes and Self-Test Numbers
B-9
Error Number Terminal Message
675 or 684 Required network node(s) not found
676 or 685
677 or 686
678 or 687
679 or 688
681 or 690
File access error
Unstable DH+ network
Duplicate node detected
No active Node(s) found on network
DH+ hardware failed
DH+ Terminal Messages
Type
Comm Status
Comm Status
Comm Status
Comm Status
Comm Status
Meaning
The network is active, but the logic controller(s) are not located at the expected nodes.
Recommended Action
Verify that the logic controller(s) required by the application are at the expected node addresses and that the communication parameters are set properly.
1. The data files do not exist on the controller. Create the data files.
1. The terminal is trying to access one or more controller data files that are unavailable.
2. If the message is flashing, the terminal is trying to read or write data files that are unavailable.
Corrupt data packets or intermittent system configuration was detected on DH+ network.
More than one node was assigned the same address.
No other DH+ devices can be located on the network.
2. The data file is smaller than what is required. For example, the PanelView uses
N7:10 but only N7:0 is defined in the controller.
Verify all controller addressing and baud rate settings. Check for loose or reversed wiring.
Verify all device nodes.
Verify that PanelView terminal and logic controller(s) are correctly connected to the system.
Check cable and wiring.
Comm Status During startup, the terminal detected a missing, corrupt, or nonfunctional DH+ card. The terminal will run but not communicate.
If error continues, verify that baud rates on the terminal and controller are the same. Communication resumes when the problem is corrected.
Contact technical support and provide the specific terminal message.
Publication 2711-6.1
B-10
Messages, Codes and Self-Test Numbers
Error Number
675 or 682
676 or 683
679 or 686
681 or 688
Terminal Message
Required network node(s) not found
File access error
Panelview offline
DF1 hardware failed
DF1 Terminal Messages
Type
Comm Status
Comm Status
Comm Warning
Comm Status
Meaning
The network is active, but the logic controller(s) are not located at the expected nodes.
Recommended Action
Verify that the logic controller(s) required by the application are at the expected node addresses and that the communication parameters are set properly.
The data files do not exist on the controller. Create the data files.
The terminal is trying to access one or more controller data files that are unavailable. If the message is flashing, the terminal is trying to read or write data files that are unavailable.
PanelView is offline.
During startup the terminal detected a missing, corrupt, or nonfunctional DF1+ card. The terminal will run but not communicate.
Check connections
Contact technical support and provide terminal message.
Publication 2711-6.1
Messages, Codes and Self-Test Numbers
B-11
Terminal Codes
Terminal Codes are displayed on the PanelView terminal during operation or terminal configuration.
DeviceNet Codes
Comm Status codes appear as a banner at the top of an application screen or as an LED status on the terminal’s Configuration screen.
Error 634 appears in upper left of banner. Codes less than 12 are minor faults and clear automatically when corrected. Codes above 12 require a terminal reset to clear.
DeviceNet
Comm Status
Code
1
Indicates:
2
3
4
5
6
7
10
11
12
13
Recommended Action
No connections established. Occurs on power-up until a device connection is established on the network.
A connection is in the timed out state. Occurs when I/O polling stops after an I/O poll connection is running.
An peer tag cannot be obtained. Occurs if the device associated with a peer tag is not responding or the peer tag does not exist at the specified class, instance, and attribute number.
A zero length I/O message was received placing the I/O application in idle mode. Occurs when scanner is in program mode.
Message Overrun. Message traffic from the PanelView is being generated quicker than it is possible to send the data. Occurs with large I/O sizes when Change-Of-State is being used and state changes are occurring very quickly or if polling too fast.
Offline Connection Set Identify Received. An Offline Connection Set Point-to-Point Identify Message has been received. Occurs if a Client device on the network capable of executing the Offline Connection Set sends a Point-to-
Point Identify message to the terminal while it is in the
Offline State. (It failed Duplicate MAC ID Detection on startup).
A Listen Only connection has timed out. It has not received a message in at least four times the expected packet rate value. This occurs if the message associated with the Listen Only tag is not occurring or was not identified correctly.
Autobaud in Progress. Occurs on startup while the Autobaud process is executing.
No network power detected. Occurs if network 24V is not present.
Dup MAC Failure. Occurs if the PanelView powers up with the same Node Address present on the network.
Bus-off Interrupt occurred. CAN Chip is held in reset.
Caused by noise on network signal lines or an attempt to connect to the network at the wrong baud rate.
Establish a connection over DeviceNet to the PanelView.
Check that the network wiring and that the master device
(scanner) is operational.
Ensure the data location is correct and that the end device is attached and operational. For write tags, ensure that the appropriate attribute is targeted. If the targeted device is UCMM capable, ensure it has enough explicit message connections to allow the PanelView to take one. If the targeted device is not UCMM capable, ensure that it is owned by a Master device (scanner).
Error clears when switched back to run. Correct the problem of the Master sending the I/O idle condition.
Slow down I/O polling or the state changes generating
Change-of-State I/O messages. Use Cyclic I/O at a fast heartbeat rate rather than Change-of-State. Use the production inhibit capability on the master.
No action required. The error clears within 500 ms of the last Identify message sent.
Check that the Listen Only tags are properly configured.
Verify that the associated message is occurring at the expected packet rate. DeviceNet traffic monitor may be helpful.
No action required. The error clears within 10 seconds, the maximum time allowed to detect a baud rate.
Check the wiring. This message will clear automatically when 24V power is restored.
Change the node address to an unused address and reset the terminal.
Check baud rate and network wiring, including termination resistors. Reset the terminal.
Publication 2711-6.1
B-12
Messages, Codes and Self-Test Numbers
Alert codes appear as a box in the middle of the screen. Error 636 appears in the upper left corner. Operation of the terminal continues.
Alert messages can be cleared.
DeviceNet
Alert Code
2
Indicates:
3
4
7
8
10
12
14
15
16
19
20
23
38
Recommended Action
Unsupported DeviceNet Message received. The Network Access Object received a message that is not supported.
Initial Writes Failure. The Motherboard failed to send all input data to the daughter card prior to network startup.
Invalid Peer Address. Occurs at runtime if the node address of a peer tag is the same as the PanelView.
Should not occur in normal operation. Clear the message. If problem re-occurs, contact technical support.
Should not occur during normal operation.
Clear the message. If problem reoccurs, contact technical support.
Change-Of-State Input Overrun. Occurs if PanelView state changes on I/O input data occurs faster than the
PanelView can send them to the I/O scanner.
Clear the message and determine which tag in the application is pointing to the Panel-
View’s node address. Correct the application.
Clear the message. Excessive network traffic could cause this problem if inputs are changing rapidly.
An external network process has caused the reset of the network access process. Connections are temporarily lost. Occurs if an external device sends an Identify Object Reset Service to the terminal or if an external device changes the terminal’s node address
(directly or using the Offline Connection Set).
No action required. Any server connections will need to be re-established.
Unsupported DeviceNet message received.
Invalid ASA Number (0x00000000 or 0xFFFFFFFF).
Occurs if the flash memory is corrupt or an invalid
ASA number was programmed.
Should not occur during normal operation.
Clear the message. If problem reoccurs, contact technical support.
Clear the message. The message occurs each time the terminal is reset. The terminal operates normally but you should correct the problem. Contact technical support.
Get Next Scan Item Failed in peer mode.
Should not occur in normal operation. Clear the message. If problem reoccurs, contact technical support.
Peer Input Data not received. Will occur if an input
(push button) changes a second time before its previous state was sent on the network. Only for Peer tags.
Clear the message. Excessive network traffic could cause this problem if inputs are changing rapidly. Handle high speed input data over
I/O connections if possible.
Clear the message and if the problem reoccurs, consult technical support.
I/O Connection Size does not match size of I/O data in
Assembly Instances 1 & 2. Programmed connection sizes for I/O do not match the amount of data represented by the I/O type tags.
Get Next Contact Request Failure. In Peer Mode scanning, the request to obtain the next tag in current context failed.
Should not occur in normal operation. Clear the message. If problem reoccurs, contact technical support.
Start the terminal when network traffic exists or use a fixed baud rate.
Autobaud Failure. The autobaud process failed to detect a valid baud rate within 10 seconds. Occurs if network traffic is nonexistent or intermittent.
Nonvolatile Objects have been reset. Nonvolatile storage of some objects required a full reset on powerup.
Certain nonvolatile values will be reset to defaults.
Can occur when the daughtercard firmware in the terminal is upgraded. Clear the message and continue. If problem reoccurs, contact technical support.
An external client device on the network has performed a Set Attribute request on the Baud Rate setting. The baud may be different on next terminal reset.
Confirm the Active Baud on the
Communication Setup screen of the terminal.
Publication 2711-6.1
Messages, Codes and Self-Test Numbers
B-13
Fault codes appear as a full screen box with Error 635 appears in the upper left corner. Reset the terminal to clear the condition. If the problem reoccurs, note the 2-digit code and contact technical support.
DeviceNet
Fault Code
5
Indicates: Recommended Action
6
13
17
18
33
37
39
20xx
9-11, 21, 22,
24-36
PCCC Message Transaction error during the transfer Should not occur in normal operation. Clear the message. If problem re-occurs, contact technical support.
Stack overflow fault Should not occur during normal operation.
Clear the message. If problem reoccurs, contact technical support.
Invalid Screen Context Priority Received
Client Object Failed
Should not occur during normal operation.
Clear the message. If problem reoccurs, contact technical support.
Should not occur during normal operation.
Clear the message. If problem reoccurs, contact technical support.
CAN Chip Failed to initialize
I/O Assembly Remap Error
Should not occur during normal operation.
Clear the message. If problem reoccurs, contact technical support.
Revalidate the application and download. If problem re-occurs, contact technical support.
The size of a particular channel exceeds the size limitation set by the daughtercard.
Should not occur during normal operation.
Clear the message. If problem reoccurs, contact technical support.
The application contains more Listen Only channels that the daughtercard supports.
Critical Internal DeviceNet firmware fault
Internal faults associated with motherboard/daughtercard communications
Reset the terminal. If problem re-occurs, contact technical support.
Should not occur during normal operation.
Clear the message. If problem reoccurs, contact technical support.
Should not occur during normal operation.
Clear the message. If problem reoccurs, contact technical support.
Publication 2711-6.1
B-14
Messages, Codes and Self-Test Numbers
ControlLogix Codes
ControlLogix
Terminal
Alert Code
603
9020
Alert Type
Critical fault
Critical fault
Indicates:
File download error
An internal fault occurred.
Recommended Action(s)
Reset the terminal. If problem occurs again, contact technical support.
Reset the terminal. If problem occurs again, contact technical support.
ControlNet Codes
These errors appear at the top of the application screen or on the terminal’s configuration screen. If you should get an alert number that is not listed, contact technical support.
ControlNet
Error Code
1803
1824
1826
1828
1829
3333
Alert Type
Informational
Warning
Warning
Warning
Warning
Warning
Indicates: Recommended Action(s)
The communications device has completed the request to force the device into the listen-only state.
The PanelView was detected as having a duplicate node address and is in the listen-only mode. Check the node address (MAC ID) of the devices on the network to verify that addresses are not duplicated.
The PanelView was forced to a listenonly state.
A fixed tag packet was received but there is no place to route the packet.
The data packet is discarded and the error message is displayed.
An attempt was made to open an unsupported transport class.
An attempt was made to open a
Class 1 transport with application triggering or a Class 3 transport with cyclic triggering.
A connection has timed out.
Contact technical support.
Contact technical support.
Contact technical support.
Contact technical support.
A file transfer was unexpectedly interrupted. Try to transfer again.
Publication 2711-6.1
Messages, Codes and Self-Test Numbers
B-15
These messages appear on the terminal screen as DC Error = xx. If you get an alert number that is not listed here, contact technical support.
ControlNet
Alert Code
9000
9003
9004
9010
9012
9014
9015
9016
9017
9018
9019
9020
Alert Type
Critical fault
Critical fault
Critical fault
Critical fault
Communications Warning
Critical fault
Critical fault
Critical fault
Critical fault
Critical fault
Critical fault
Critical fault
Indicates:
Interface startup failed.
CIP S/N is not valid.
Out of buffers.
Invalid target node, target node is the same as the PanelView, or larger than the UMAX.
ControlNet object received a reset request.
A fatal CPU fault occurred.
A ControlNet hardware fault occurred.
RAM verification failed at startup.
CRC verification failed at startup.
A critical internal error occurred.
An internal fault occurred.
An internal fault occurred.
Recommended Action(s)
Contact technical support.
Contact technical support.
Contact technical support.
Check node address of all devices on the network including the PanelView terminal.
Contact technical support.
Contact technical support.
Contact technical support.
Contact technical support.
Contact technical support.
Contact technical support.
Reset terminal, if problem occurs again, contact technical support.
Reset terminal. If problem occurs again, reload application. If problem persists, contact technical support.
Publication 2711-6.1
B-16
Messages, Codes and Self-Test Numbers
Remote I/O Communication Loss
When communication fails on a Remote I/O network:
• Object states are maintained and the message "No PLC
Communication" is displayed on the screen.
• If Block Transfers are defined for the application, but no BTR or
BTW instructions are received, another message appears when the Block Transfer Timeout occurs.
These messages continue to display until communications is established. If a write operation is attempted to the logic program controlling the PanelView objects, the terminal will display the message "Error: Write to Logic Controller failed".
If a PanelView object is activated during a communication loss, the object retains its new state and sends this state value to the controller when communications is established.
Publication 2711-6.1
Self-test Numbers
Messages, Codes and Self-Test Numbers
The self-test numbers appear on the screen during powerup.
B-17
COPYRIGHT ALLEN-BRADLEY COMPANY
1999, ALL RIGHTS RESERVED VXX.XX
TESTING VERIFICANADO PRUFEN
VERIFICATION AUTOTEST
2
Self-test Number
Test Number
1
2
10
11
12
13
24
25
26
30
20
21
22
23
31
32
33
34
Indicates
STATIC RAM test
Terminal searching for a file to download.
Erase boot flash area.
Copy boot code
Boot code copy successful
Boot code copy failed. Check for error after boot code is copied to the onboard flash EPROM.
Erase firmware from flash EPROM
Copy firmware to firmware flash memory
Firmware copy successful
Firmware copy failed
Performed CRC base firmware check
Firmware not compatible with boot code
Firmware not compatible with hardware
Watchdog test
Stuck key test
Real time clock test
LCD RAM failed
Performed CRC extended firmware check
Note: You may not see all of these test numbers during a powerup.
If a test fails, the terminal displays:
ERROR!
FEHLER!
ERREUR!
ERRORE!
The following test numbers appear only if a problem occurs.
Test Number
40
50
60
Indicates
No executable code to run after boot
Wrong memory card format
CPU could not execute code
Publication 2711-6.1
B-18
Messages, Codes and Self-Test Numbers
The table below shows fault conditions that may occur during powerup.
Fault Indicator
Solid Red
Blinking Red
(6 times per second)
Blinking Red
(5 seconds on/5 seconds off)
Indicates
Static RAM Test failed. Contact technical support.
Checksum test on boot code failed. Contact technical support.
Boot code is incorrect for terminal type
(touch screen or keypad). Contact technical support.
Publication 2711-6.1
Appendix
C
European Union Directive Compliance
If the PanelView Operator Terminals are installed within the European
Union or EEA regions and have the CE mark, the following regulations apply.
EMC and Low Voltage Directives
These apparatuses are tested to meet Council Directive 89/336/EEC
Electromagnetic Compatibility (EMC), and amending directives
92/31/EEC, 93/68/EEC; 73/23/EEC Low Voltage Directive, and amending directive 93/68/EEC using the following standards, in whole or in part:
Emissions (Class B: Light Industrial)
EN50081- 1:1992
Emissions (Class A: Industrial)
EN50081-2:1993
Immunity (Industrial) EN50082-2:1995
Programmable Controllers
Equipment Requirements and Tests)
EN61131 2:1995
Low Voltage Directive
(Safety Sections of EN61131-2)
300 x x x x
550 x x x x
600 x x x x
2
900M 900C 1000G 1000C 1400 x x x x x x x x
1
DEMKO prEN5002 1 Ex Na Group IIC, T4
x
1
DeviceNet PanelView terminals are Class A for Emissions
2 Does not apply to 600 touch screen only terminals
x
1
x x x x x x x x x x x x
Intended Use of Product
According to these Standards, the factor which determines, for EMC purposes, whether a product is deemed to be "Industrial" rather than
"Residential, commercial or light industrial", is given in clause 1 of
EN50081-2 as follows:
Apparatus covered by this standard is not intended for connection to a public mains network supplied from a high- or mediumvoltage transformer dedicated for the supply of an installation feeding a manufacturing or similar plant.
When installed in Europe, any other application is in contravention of
European Union Directives, and a breach of these laws.
The PanelView 900 color, the 1000 grayscale and the 1400 terminals are certified for direct connection to a low-voltage public mains supply or to a dedicated source, which is intended to interface to a low-voltage public mains supply.
Publication 2711-6.1
C-2
European Union Directive Complaince
Wiring Recommendations
To reduce electrical noise, connect the PanelView terminal to its own branch circuit. The input power source should be protected by a fuse or circuit breaker rated no more than 15 amps. Route incoming power to the PanelView terminal by a separate path from the communications cable.
Where power and communication lines must cross, they should cross at right angles. Communication lines can be installed in the same conduit as low level DC I/O lines (less than 10 Volts).
Declarations of Conformity
Declarations of Conformity are available for each of the PanelView terminals at the website www.ab.com/support under Product
Certification.
Publication 2711-6.1
Glossary
adapter
ControlNet device which responds to scanner messages (also called slave device).
address
1) A character string that uniquely identifies a memory location. 2) A character string that uniquely identifies the physical location of an input or output circuit.
application
In the context of PanelBuilder32, an application is a logical arrangement of screens which replace the functions of a control panel and consist of push buttons, data entry objects, control lists and indicators. The application runs in a PanelView terminal.
application file
File containing configuration information for a PanelView terminal.
Files exist in either a PanelView (.PVA) or a PanelBuilder32 (.PBA) format. Files transferred to a terminal are in a .PVA format. Files within PanelBuilder32 are in a .PBA format.
ATA card
Advanced Technology Attachment (ATA), Intelligent Drive
Electronics (IDE), PC Cards (formerly PCMCIA) combine the drive controller and memory storage device. ATA cards can be accessed with standard Copy or Delete commands on a computer. The card looks like a hard drive to the user. You can use the card on a variety of computers without any special setup.
baud
A unit of signaling speed equal to the number of discrete conditions or signal events per second.Where one bit is encoded on each signalling event, the number of baud is the same as the number of bit/s.
boot revision
Revision number of the terminal boot code.
bridge
Device that allows network data to pass from one link to another link.
controller
A unit, such as a programmable controller or relay panel, that controls machine or process elements.
Publication 2711-6.1
G-2
Glossary
cursor keys
Up, down, left, right arrows on the terminal keypad. These keys are used to move a selection cursor or the active object indicator bar.
DF1
Allen-Bradley communication protocol based on an ANSI X3.28-
1976 specification.
download
See upload/download.
DH-485 link
Data Highway 485 link. An Allen-Bradley token-passing carrier-band link for a local area network.
DH+ link
Data Highway Plus link. An Allen-Bradley token-passing baseband link for a local area network.
EMI
Electromagnetic Interference. Any electromagnetic disturbance that interrupts, obstructs, or otherwise impairs the performance of electronic equipment.
EPROM
Erasable Programmable Read-only Memory. A PROM that can be erased, usually with ultraviolet light, then re-programmed with electrical signals. As with all PROMs, it is nonvolatile random-access memory.
EEPROM (flash)
Electrically-Erasable PROM. A type of PROM that can be erased and re-programmed by electrical signals. As with all PROMs, it is nonvolatile random-access memory. Used by the PanelView terminals to stored applications.
firmware
Logic stored in read-only memory.
function keys
Set of keys (labeled F1-F10, F1-F16 or F1-21) on the PanelView terminals used to initiate functions. The function keys are userdefined and may have custom labels.
Publication 2711-6.1
Glossary
G-3 interscan delay
Determines the amount of time the PanelView waits before re-reading the current screen data from the logic controller.
keeper
The network controller of a ControlNet network.
keypad
Set of 14 keys (numeric 0-9, decimal point, backspace, minus, and enter) to the right of the display on keypad terminals. These keys are used to enter data.
LED
Light-Emitting Diode.
Memory Card
A storage medium which can store a PanelView application and/or a font file.
MicroLogix
An Allen-Bradley programmable controller.
NEMA standards
Consensus standards in the United States for electrical equipment approved by the members of the National Electrical Manufacturers
Association (NEMA).
network
Collection of connected nodes including the connection paths, repeaters, and bridges.
Network Access Point (NAP)
Port providing temporary access to a ControlNet network through the
RJ-45 connector.
Network Update Time (NUT)
The ControlNet network update time established for the communications link.
node
The connection point at which medium access is provided.
PanelBuilder32 software
A Windows program used to develop applications which run in
PanelView terminals.
PanelView terminal
An Allen-Bradley keypad or touch screen terminal providing the operator interface to the logic controller when an application is executing.
Publication 2711-6.1
G-4
Glossary
PC
1) Personal Computer. 2) Programmable Controller. 3) Printed
Circuit.
PCCC
Acronym for Programmable Controller Communication Commands.
PLC controller
1) An Allen-Bradley programmable controller with a name that has the prefix PLC. See programmable controller.
preset value
A value loaded into a controller data table when an application is first started.
programmable controller
A solid-state control system that has a user-programmable memory for storage of instructions to implement specific functions such as I/O control, logic, timing, counting, report generation, communication, arithmetic, and data file manipulation. A controller consists of a central processor, input/output interface, and memory. A controller is designed as an industrial control system.
real time clock
Internal clock that provides time, day, month and year.
remote I/O
1) I/O connected to a processor across a serial link. With a serial link, remote I/O can be located long distances from the processor.
remote I/O link
A serial link for carrying I/O data between a PLC or SLC processor/ scanner and remote I/O adapters.
repeater
Two-port component that receives and transmits all data from one segment to another.
restore
To load an application from a memory (PC) card.
RS-232
An EIA standard that specifies electrical, mechanical, and functional characteristics for serial binary communication circuits in a point-topoint link.
RS-485
An EIA standard that specifies electrical characteristics of balancedvoltage digital interface circuits in a multi-point link.
Publication 2711-6.1
Glossary
G-5 scheduled messages
Messages that occur at a regular specified interval. They are assigned a particular portion of the network update time (NUT) and are always transmitted at that time.
safety extra-low voltage (SELV)
A voltage which, under all operating conditions does not exceed 42.4
V peak or dc between conductors, or between any conductor and earth, in a circuit which is isolated from the main power supply by means of a safety isolating transformer or an equivalent means.
National regulations have to be considered for a correct isolation voltage rating.
scratchpad
A window that appears in the center of the terminal display that allows data entry using the terminal or screen keypad.
screen
1) the viewing surface on which data is displayed. 2) The visual image on a screen.
segment
Trunk-cable sections connected through taps with terminators at each end and no repeaters.
SLC
An Allen-Bradley programmable controller with a name that has the prefix SLC.
SMAX
Highest ControlNet node address which can communicate during the scheduled portion of the network update interval.
tap
Hardware component that connects devices to the ControlNet trunk cable.
touch cell
1 of 128 or 384 rectangular areas on the terminal display that can sense when touched.
touch screen
The display window of the terminal that responds when touched.
trunk cable
Bus or central part of a cable system.
unscheduled messages
Messages that are sent on an as needed basis. Unscheduled messages are sent during the unscheduled portion of the network update interval.
Publication 2711-6.1
G-6
Glossary
UMAX
Highest ControlNet node address which can communicate during the unscheduled portion of the network update interval.
upload/download
Commonly referred to the reading/writing across a link relatively large blocks of data from one device to another. Whether it is considered an upload or download may depend upon whether it is a read or write and upon which device initiates the transaction. When data is transferred to a programming device, it is considered an upload. When data is transferred from a programming device, it is considered a download.
Publication 2711-6.1
A
AC power
accessories
alarms
Allen-Bradley, contacting for assistance
application files
ASCII entry controls
entering data
scratchpads
audience
B
C
cables
DF1
DH-485
RS-232
certifications
Comm LED
communication ports, available
configuration screens
DF1
DH-485
printer setup
screen setup
time and date
activating
ControlNet communications
Index
Publication 2711-6.1
I-ii
Index
D
data entry
ASCII entry keypad enable button
, 5-6 numeric entry cursor point
date and time setup
DC power
degaussing PanelView 1400 enabling/disabling
DeviceNet communications
output size
DF1 communications
Comm LED
connecting to a DeviceNet network
connecting to a MicroLogix 1000
, 11-28 connecting to an SLC or PLC
DF1 port pinouts
serial communication parameters
using a modem
Publication 2711-6.1
DH+ communications
cable
node
DH-485 communications
node address
ports
SLC connection
display
displays
E
European Union Directive Compliance
F
I
indicators
Installing the PanelView 1000
Installing the PanelView 1400 clip mounting
stud mounting
Installing the PanelView 300
Installing the PanelView 550
Installing the PanelView 600
Index I-iii
Installing the PanelView 900
K
key repeat
keypad terminals
L
language selection
types
LEDs
Comm
list keys
M
restoring application from card
Publication 2711-6.1
I-iv
Index
types
messages
Remote I/O
, B-14 status
warning
N
numeric entry controls
entering data
scratchpad
P
PanelView 1000
screen adjustments
PanelView 1400
, 3-24 aligning the touch grid
screen adjustments
Publication 2711-6.1
PanelView 300
PanelView 550
screen adjustments
PanelView 600
screen adjustments
PanelView 900
screen adjustments
PanelView terminals
types
Pass-Through
personal computer interface converter
PIC converter
power connection
RS-232 terminals
preset operations
powerup screen
, 3-16 restart and load values
printer port setup
configuring
printing
push buttons
R
Remote I/O communications
cable
connecting to a Remote I/O scanner
last chassis
Pass-Through
rack number
resetting
PanelView 1000
PanelView 1400
Index
RS-232 (DH-485) communications
SLC connection
RS-232 serial port
configuring
run mode
S
scale, bar graph
scratchpad
screen selectors
specifications
PanelView 1000
PanelView 1400
T
terminal information
terminals
types
I-v
Publication 2711-6.1
I-vi
Index
time and date setup
touch screen terminals
troubleshooting
W
write protection
Publication 2711-6.1
Index I-vii
Publication 2711-6.1
Back Cover
Publication 2711-6.1 - March 2000
Supersedes Publication 2711-6.1 - November 1999
40061-360-01(F)
© Copyright 2000 Rockwell International Corporation. Printed in the U.S.A.
Advertisement
Key Features
- Various display sizes and types
- Touch screen or keypad operator input
- Multiple communication options
- Memory card support for application storage
- User-friendly interface for easy operation
- Built-in alarm handling
- RS-232 printer port for outputting data
- Configuration mode for customization
- Support for various programming software
- Wide range of accessories available
