USER`S MANUAL - Bison Gear and Engineering Corporation

USER`S MANUAL - Bison Gear and Engineering Corporation
USER’S MANUAL
Models
170-303-0003
170-303-0010
170-343-0003
170-343-0010
SCR, Dual Voltage, Adjustable-Speed
Regenerative Drives for DC Brush Motors
Copyright © 2006 by
Bison Gear & Engineering
All rights reserved. No part of this manual may be reproduced or transmitted in any form
without written permission from Bison Gear & Engineering. The information and technical data in this manual are subject to change without notice. Bison Gear & Engineering
and its Divisions make no warranty of any kind with respect to this material, including,
but not limited to, the implied warranties of its merchantability and fitness for a given
purpose. Bison Gear & Engineering and its Divisions assume no responsibility for any
errors that may appear in this manual and make no commitment to update or to keep
current the information in this manual.
Printed in the United States of America.
i
Safety Warnings
•
This symbol
denotes an important safety tip or warning.
Please read these sections carefully prior to performing any of
the instructions contained in that section.
•
Have a qualified electrical maintenance technician install, adjust
and service this equipment. Follow the National Electrical Code
and all other applicable electrical and safety codes, including the
provisions of the Occupational Safety
and Health Act (OSHA), when installing equipment.
•
Reduce the chance of an electrical fire, shock, or explosion by
proper grounding, over-current protection, thermal protection, and
enclosure. Follow sound maintenance procedures.
•
It is possible for a drive to run at full speed as a result of a
component failure. Please ensure that a master switch has been
placed in the AC line to stop the drive in an emergency.
•
This drive is not isolated from earth ground. Circuit potentials
are at 115 VAC or 230 VAC above earth ground. Avoid direct
contact with the printed circuit board or with circuit elements to
prevent the risk of serious injury or fatality. Use a non-metallic
screwdriver for adjusting the calibration trimpots.
ii
Contents
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Regenerative Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Mounting chassis drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Mounting cased drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Heat sinking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
AC line and motor connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Cage-clamp terminal block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Field output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Tachogenerator feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Speed adjust potentiometer installation . . . . . . . . . . . . . . . . . . . . 13
Speed adjust potentiometer connections . . . . . . . . . . . . . . . . . . . 14
+15 and –15 terminals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Line Fusing Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Voltage follower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Before applying power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Selector switch settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Chassis drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Cased drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Starting and Stopping Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Line starting and line stopping . . . . . . . . . . . . . . . . . . . . . . . 22
Automatic restart upon power restoration . . . . . . . . . . . . . . 22
Regenerative deceleration . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Regenerative brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Coast to a stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Decelerate to zero speed . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
iii
MINIMUM SPEED (MIN SPD) . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
MAXIMUM SPEED (MAX SPD) . . . . . . . . . . . . . . . . . . . . . . . . . 29
FORWARD TORQUE (FWD TQ) . . . . . . . . . . . . . . . . . . . . . . . . . 30
REVERSE TORQUE (REV TQ) . . . . . . . . . . . . . . . . . . . . . . . . . . 31
IR COMPENSATION (IR COMP) . . . . . . . . . . . . . . . . . . . . . . . . . 32
FORWARD ACCELERATION (FWD ACC) . . . . . . . . . . . . . . . . . 33
REVERSE ACCELERATION (REV ACC) . . . . . . . . . . . . . . . . . . 33
DEADBAND (DB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
TACHOGENERATOR (TACH) . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Application Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Connection to other Bison devices . . . . . . . . . . . . . . . . . . . . . . . . 38
Optional speed adjust potentiometer connections . . . . . . . . . . . . 39
Forward-Stop-Reverse Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Forward-Reverse Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Independent Adjustable Speeds (Forward Direction Only) . . . . . . 40
Independent Forward and Reverse Speeds . . . . . . . . . . . . . . . . . 41
Independent Forward and Reverse Speeds with
FWD-STOP-REV Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Factory Prewired Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Certificate of Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Unconditional Warranty . . . . . . . . . . . . . . . . . . . . . . . . inside back cover
iv
Illustrations
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
1. 170-303-0010 and 170-303-0003 Dimensions . . . . . . . . . . . . . . . . . . . . 3
2. 170-343-0010 and 170-343-0003 Dimensions . . . . . . . . . . . . . . . . . . . . 4
3. Four Quadrant Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. Chassis Drive Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5. Cased Drive Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6. Cage-Clamp Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7. Speed Adjust Potentiometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
8. Speed Adjust Potentiometer Connections . . . . . . . . . . . . . . . . . . . . . . 14
9. TB502 Terminal Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
10. Voltage Follower Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
11. Selector Switch Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
12. Regenerative Deceleration Switch Connection . . . . . . . . . . . . . . . . . . 22
13. INHIBIT Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
14. Inhibit - Run Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
15. Inhibit - Run Terminals Location and Run / Coast Switch . . . . . . . . . . 25
16. Run/Decelerate to Zero Speed Switch . . . . . . . . . . . . . . . . . . . . . . . . 26
17. Typical FWD TQ, REV TQ, and IR COMP Settings . . . . . . . . . . . . . . 34
18. Deadband Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
19. Connections to 170-993-0200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
20. Forward-Reverse Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
21. Forward-Stop-Reverse Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
22. Independent Adjustable Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
23. Independent Forward and Reverse Speeds . . . . . . . . . . . . . . . . . . . . 41
24. Independent Forward and Reverse Speeds with a
Forward-Stop-Reverse Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 25. Prewired Connections to L1, L2(115) and L2(230) . . . . . . . . . . . . . . . 47
Figure 26. Prewired Speed Adjust Potentiometer Connections . . . . . . . . . . . . . . 48
v
Tables
Table 1. Field Output Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 2. Fuse Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 3. Corcom® Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
1
Specifications
Model
Max.
Armature
Current
(Amps DC)
HP Range
with 115 VAC
Applied
HP Range
with 230 VAC
Applied
* 170-343-0010, 170-303-0010
10.0 †
1/4–1 †
1/2–2 †
* 170-343-0003, 170-303-0003
3.0
1/20–1/8
1/10–1/4
† Maximum armature current and horsepower range apply when drive is attached to additional heat sink: Bison part number 170-990-0200. Use heat sink when armature current
is above 7 ADC. Heat sinks are pre-mounted on cased drives.
* See page 2 for part number descriptions.
AC Line Voltage
115/230 VAC, ±10%, 50/60 Hz, single phase
Armature Voltage (115 VAC Input)
0–90 VDC
Armature Voltage (230 VAC Input)
0–180 VDC
Form Factor
1.37 at base speed
Field Voltage (115 VAC Input)
50 VDC (F1 to L1); 100 VDC (F1 to F2)
Field Voltage (230 VAC Input)
100 VDC (F1 to L1); 200 VDC (F1 to F2)
Max. Field Current
1 ADC
Accel. Time Range (with no load)
0.5 – 15 seconds
Decel. Time Range (with no load)
0.5 – 15 seconds
2
Analog Input Voltage Range (signal must be isolated; S0 to S2)
Input Impedance (S0 to S2)
0 - ±10 VDC
32K ohms
Load Regulation
with Armature Feedback
with Tachogenerator Feedback
1% of base speed or better
0.1% of base speed
Ambient Temp. Range (chassis drives)
10°C–55°C
Ambient Temp. Range (cased drives)
10°C–40°C
Vibration
0.5g max (0 – 50 Hz)
0.1g max (above 50 Hz)
3
Dimensions
4 .7 8 [1 2 1 ]
4.78
[121]
0 .2 8 [7
]
0.28
[7]
4 .0 0 0 [1 0 2 ]
4.000
[102]
[1 8 [18]
]
0.70
.7 0
L1
L2
230V
GND
L2
11 5 V
F1
F2
A2
0 .1 8 8[5]
[5 ]
0.188
A1
C 504
C 505
TB 502
S3
TB 501
C 503
SW 501
11 5
FU502
FU501
IC 5 0 2
230 230
FA S T A C T IN G
FU S ES O N LY
S 0 R B 1 R B 2 - 15 + 15 T 1
L2
S1
L1
S2
115
SW 502
C 502
SC R501
IC 5 0 1
T505
FU 504
SC R502
R501
SO502
SO501
IN H IB IT
IN H - R U N
T2
T501
SC R503
IN V
SC R504
P502
C 501
P501
M IN S P D F W D T Q
8.40
8 .4 0 [213]
[2 1 3 ]
26]
8.90[2[228]
8 .9 0
T502
P503
SC R505
P504
SC R506
T503
R504
P505
P506
R505
SC R507
R506
SC R508
T504
P507
TAC H
P509
SW 504
DB
P508
SW 503
R E V T Q IR C O M P M A X S P DF W D A C CR E V A C C
FEED B A C K
A R M A TU R E
TA C H
90
1 8 0A R M
C 5 10
R502
R503
4]
0.93[2[24]
0 .9 3
0 .6 4
1 .8 5 [4 7 ]
1.85
[47]
[1 6 ]
0.84 [18]
3 .5 0 [8
9]
3.50
[89]
0.125
0 .1 2 5[3]
[3 ] REF
REF
Optional 170-990-0200 Heatsink Dimensions: 9.8” x 6.9” x 1”
Figure 1. 170-303-0010 and 170-303-0003 Dimensions
4
Figure 2. 170-343-0010 and 170-343-0003 Dimensions
5
Regenerative Drives
In most non-regenerative, variable speed, DC drives control current flows to a motor in one direction. The direction of current
flow is the same direction as the motor rotation.
Non-regenerative drives operate in Quadrant 1, and also in
Quadrant 3 if the drive is reversible (see Figure 3, page 6).
Motors must stop before reversing direction. Non-regenerative
drives cannot oppose an overhauling load, and cannot decelerate
a load faster than coasting to a lower speed.
Regenerative drives operate in two additional quadrants:
Quadrant 2 and Quadrant 4. In these quadrants, motor torque is
in the opposite direction of motor rotation.
Regenerative drives can reverse a motor without contactors,
switches, brake resistors, and inhibit plugs. They can also control
an overhauling load and decelerate a load faster than it would
take to coast to a lower speed.
6
Figure 3. Four Quadrant Operation
7
Installation
Mounting chassis drives
Drive components are sensitive to electrostatic fields. Avoid contact with the circuit board directly. Hold the drive by the chassis
only.
Protect the drive from dirt, moisture, and accidental contact.
Provide sufficient room for access to the terminal block and calibration trimpots.
Mount the drive away from other heat sources. Operate
the drive within the specified ambient operating temperature
range.
Prevent loose connections by avoiding excessive vibration
of the drive.
Mount the drive with its board in either a horizontal or
vertical plane. Six 0.18 inch (4.57 mm) wide slots in the chassis
accept #8 pan head screws. Fasten either the large
base or the narrow flange of the chassis to the subplate.
The chassis must be earth grounded for noise suppression. To
ground the chassis, connect earth ground to the GND terminal
on terminal block TB501.
8
Mounting cased drives
NEMA 4X cased drives come with three 0.88 inch (22 mm) conduit knockout holes at the bottom of the case. The units may be
vertically wall mounted using the four 0.25 inch
(6 mm) slotted holes on the attached heat sink. For motor loads
less than 5 ADC, the drive may be bench mounted horizontally,
or operated without mounting.
1. Set the POWER switch to the “0” or OFF position before
applying the AC line voltage.
2. Install the mounting screws.
3. For access to the terminal strip, turn the slotted screw on the
front cover counterclockwise until it is free from the case. The
right side of the cover is hinged to the case. Lift or pull the
slotted screw to open the case.
4. Carefully remove the conduit knockouts by tapping them into
the case and twisting them off with pliers.
5. Install conduit hardware through the 0.88 inch (22 mm) conduit holes. Connect external wiring to the terminal block.
6. Grasp the slotted screw and tilt the front cover back into
place. Avoid pinching any wires between the front cover and
the case.
7. Turn the slotted screw clockwise until tight to secure the front
cover.
9
Heat sinking
170-303-0010 models require an additional heat sink
when the continuous armature current is above 7 ADC. Use
Bison® part number 170-990-0200. All cased drives have sufficient heat sinking in their basic configurations. Use a thermally
conductive heat sink compound (such as Dow Corning® 340
Heat Sink compound) between the drive chassis and the heat
sink surface for optimum heat transfer.
AC line and motor connections
S3
Use 14 AWG or 16 AWG standard wire for connecting the
line and the armature. Use 16 AWG or 18 AWG standard wire
when connecting the field of a shunt wound motor. Strip the wire
insulation 0.25 inches (6 mm). See Figures 4 and 5 (page 10)
for AC line and motor connections to chassis and cased drives.
TB501
C504
TB502
C505
L1
L2
230V
L2
115V
GND F1
F2
A2
A1
A
AC LINE
INPUT
230 VAC
115 VAC
FIELD OUTPUT
115 OR 230 VAC
For Shunt Wound
Motors Only.
See field output section for
connections
Figure 4. Chassis Drive Connections
ARMATURE
OUTPUT
REV
SC R504
P50
10
P502
M IN S P D F W D T Q
T502
T2
SO502
C 502
S0 RB 1RB 2 - 15 + 15 T1
3
SO501
2
IN H - R U N
1
IN H IB IT
P501
C 501
IC 5 0 1
FU501 FU502
F A S T A C T IN G
FU S ES O N LY
SW 501
IC 5 0 2
C 503
S2
230 VAC
S1
L2
115
L1
S3
115
VAC
230 230
115
SW 502
AC LINE INPUT
C 504
TB 501
L1
L2
230V
L2
115 V
GND F 1
F2
A2
A1
TB 502
C 505
115 OR 230 VAC
A
FIELD OUTPUT
For shunt wound motors
only. See field output section for connections.
Figure 5. Cased Drive Connections
ARMATURE
OUTPUT
11
Cage-clamp terminal block
Connections to these drives are made to a cage-clamp terminal
block (see Figure 6). To insert a wire into the terminal block,
press down on the lever arm using a small screwdriver. Insert
stripped wire into the large opening in front of the terminal
block. Release the lever arm to clamp the wire.
Lever Arm
Wire Clamp
Figure 6. Cage-Clamp Terminal Block
12
Field output
The field output is for shunt wound motors only. Do not
make any connections to F1 and F2 when using a permanent
magnet motor.
Use 18 AWG wire to connect the field output to a shunt wound
motor. Table 1 lists the field output connections.
Table 1. Field Output Connections
Line Voltage
(VAC)
115
115
230
230
Approximate
Field Voltage (VDC)
50
100
100
200
Connect Motor
Field To
F1 and L1
F1 and F2
F1 and L1
F1 and F2
Tachogenerator feedback
Using tachogenerator feedback improves speed regulation from
approximately 1% of motor base speed to approximately 0.1%
of motor base speed. Use tachogenerators rated from
7 VDC per 1000 RPM to 50 VDC per 1000 RPM. Connect the
tachogenerator to terminals T1 and T2 of terminal block TB502.
The polarity is + for T1 and – for T2 when the motor running in
the forward direction. The polarity is reversed when the motor is
running in the reverse direction.
13
Speed adjust potentiometer installation
Warning
Be sure that the potentiometer tabs do not make contact with
the potentiometer enclosure. Grounding the input will cause
damage to the drive.
On chassis drives, install the circular insulating disk between the
panel and the 10KΩ speed adjust potentiometer. Mount the
speed adjust potentiometer through a 0.38 in. (0.96 cm) hole
with the hardware provided (see Figure 7). Twist the speed
adjust potentiometer wire to avoid picking up unwanted electrical noise. If potentiometer leads are longer than 18 in. (46 cm),
use shielded cable. Speed adjust potentiometers are installed on
all cased drives.
MOUNT
THROUGH
0.38 IN.
IN. (10
MOUNT
THROUGH
A A0.38
(10MM)
MM)HOLE
HOLE
CW
CW
WIPER
WIPER
CCW
CCW
NUT
NUT
STAR
STAR
WASHER
WASHER
SPEED
SPEED ADJUST
ADJUST
POTENTIOMETER
POTENTIOMETER
INSULATING DISK
INSULATING
DISK
POT
ASSIGNMENTS
POT TAB
TAB ASSIGNMENTS
PANEL
PANEL
Figure 7. Speed Adjust Potentiometer
14
Speed adjust potentiometer connections
The motor can operate in one direction (unidirectional) or in two
directions (bidirectional) depending on how the speed adjust
potentiometer is connected to the drive.
Connect the speed adjust potentiometer as shown in Figure 8(a)
for speed control in one direction.
Connect the speed adjust potentiometer as shown in Figure 8(b)
for speed control in two directions. The motor does not rotate
when the wiper is in the center position. Turning the wiper CW
from the center position causes the motor to rotate in one direction, while turning the wiper CCW from the center position
causes the motor to rotate in the opposite direction.
Refer to the Application Notes section for additional speed
adjust potentiometer connections.
TB502
TB502
10K OHM
10K
OHM
SPEED ADJUST
SPEED
ADJUST
POTENTIOMETER
S2
S2
POTENTIOMETER
10K
2W
10K OHM,
OHM, 2W
SPEED ADJUST
SPEED
ADJUST
POTENTIOMETER
POTENTIOMETER
REV
REV
TB502
TB502
S3
S3
S1
S1
S2
S2
S0
S0
FWD
FWD
S1
S1
CW
CCW
CCW
(a)
(b)
Figure 8. Speed Adjust Potentiometer Connections
for (a) Unidirectional Operation and (b) Bidirectional Operation
15
+15 and –15 terminals
Warning
Do not short the +15 and -15 terminals for any reason.
Shorting these terminals may damage the drive.
These drives can supply a regulated +15 and –15 VDC signal
(each sourcing 15 mA maximum) to isolated, external devices.
These voltage supply terminals are located on terminal block
TB502 (see figure 9).
T TB502
B 502
S3
S3
S2
S2
S1
S1
S0 RRB1
S0
B 1 RRB2
B 2 --15
15 ++15
15
T1
T1
Figure 9. TB502 Terminal Assignments
T2
T2
16
Line Fusing
Bison drives require fuses for protection. Use fast acting fuses
rated for 250 VAC or higher, and approximately 150% of the maximum
armature current. Fuse L1 when using 115 VAC line voltage. Fuse both
L1 and L2 when the line voltage is 230 VAC.
The fuse chart below lists the recommended line fuse sizes.
Table 2. Fuse Chart
90 VDC Motor
Horsepower
1/20
1/15
1/8
1/6
1/4
1/3
1/2
3/4
1
180 VDC
Horsepower
1/10
1/8
1/4
1/3
1/2
3/4
1
1 1/2
2
AC Line Fuse
Size (amps)
3
3
5
5
8
8
10
15
20
17
All drives have line fuses installed. Line fuses are rated for maximum rated curent. Use line fuses rated for 20 A or less.
Voltage follower
The drive may be wired to follow a isolated 0 to ±10V signal
instead of using a speed adjust potentiometer. Connect the signal
input to S2, and the signal common to RB1 (see Figure 10).
±10 VDC
±10VDC
S2
S2
S1
S1
COMMON
COMMON
RB1
RB1
Figure 10. Voltage Follower Connection
18
Operation
Warning
Dangerous voltages exist on the drive when it is powered.
BE ALERT. High voltages can cause serious or fatal injury.
For your safety, use personal protective equipment (PPE)
when operating this drive.
Before applying power
1. Check connections before applying AC line voltage to the
drive.
2. Check that no conductive material is present on the printed
circuit board.
3. Verify that all selector switches are set correctly (see the following section for selector switch settings).
19
Selector switch settings
1. Set the line voltage selector switches (SW501 and SW502) to
115 if using 115 VAC line voltage, or to 230 if using 230
VAC line voltage.
2. Set the armature voltage selector switch (SW503) to 90 if
using a 90 VDC motor, or to 180 if using a 180 VDC motor.
3. Set the feedback selector switch (SW504) to TACH if using a
tachogenerator; otherwise set to ARM for armature feedback.
Note: You may be required to derate a 90 VDC motor
when 230 VAC is applied to the drive.
Contact the factory for details.
See Figure 11 (page 21) for all switch locations.
Startup
Chassis drives
1. Set the speed adjust potentiometer for zero speed.
2. Apply AC line voltage.
3. Slowly advance the speed adjust potentiometer clockwise
(CW). The motor slowly accelerates as the potentiometer is
turned CW. Continue until the desired speed is reached.
4. Remove AC line voltage from the drive to coast the motor to a
stop.
20
Cased drives
1. Set the FORWARD/BRAKE/REVERSE switch to the
BRAKE position.
2. Set the speed adjust potentiometer to “0” (full CCW).
3. Apply AC line voltage.
4. Set the POWER switch to the “I” (ON) position.
5. Set the FORWARD/BRAKE/REVERSE switch to the desired
direction of rotation.
7. Slowly advance the speed adjust potentiometer clockwise
(CW). The motor slowly accelerates as the potentiometer is
turned CW. Continue until the desired speed is reached.
8. To brake the motor, set the FORWARD/BRAKE/REVERSE
switch to the BRAKE position. To coast the motor to a stop,
set the POWER switch to the “O” (OFF) position.
9. To reverse direction:
a. Set the FORWARD/BRAKE/REVERSE switch to the
BRAKE position.
b. After the motor comes to a complete stop, set the FORWARD/BRAKE/REVERSE switch to the desired direction of rotation.
10. Set the POWER switch to “O” (OFF) to remove power from
the drive.
C 504
L1
L2
230V
L2
115V
S1
S0
115
T1
SO 502
T505
SW 501
GN D
F1
F2
T2
R 5 01
SW 502
C 502
C 503
A2
IN H IB IT
M IN SP D
P 5 01
IN V
SC R 5 03
C 501
FW D TQ
P 5 02
P 5 03
R E V TQ
SC R 5 04
T503
IR C O M P
P 5 04
SC R 5 05
M A X SPD
P 5 05
P 5 06
SC R 5 07
SC R 5 08
P 5 08
DB
REV ACC
R 5 06
P 5 07
R 5 05
T504
FW D A C C
SC R 5 06
R 5 04
TA C H
P 5 09
SW 504
SO 501
IN H - R U N
SC R 5 02
FE E D B A C K
ARM
TA C H
SW 503
IC 5 01
R B 1 R B 2 - 15 + 15
230
FU 504
A R M A TU R E
90
180
S2
L2
230
SC R 5 01
C 510
R 5 02
TB 501
S3
115
FU 502
L1
FA ST A C TIN G
FU SE S O N LY
FU 501
21
R 5 03
Feedback
Selector Switch
Armature Voltage
Selector Switch
T502
T501
Line Voltage
Selector Switches
IC 5 02
TB 502
A1
C 505
Figure 11. Selector Switch Locations
22
Starting and Stopping Methods
Line starting and line stopping
Line starting and line stopping (applying and removing
AC line voltage) is recommended for infrequent starting and
stopping of a drive only. When AC line voltage is applied to the
drive, the motor accelerates to the speed set by the speed adjust
potentiometer. When AC line voltage is removed, the motor
coasts to a stop.
Automatic restart upon power restoration
All drives automatically run to set speed when power is applied.
Wiring a latching relay into the AC line is one way
to prevent automatic restarting following a power outage.
Regenerative deceleration
Short terminals RB1 and RB2
to regeneratively decelerate a
motor to a stop (Figure 12).
Since terminal RB1 bypasses
the MIN SPD circuit, shorting
RB1 and RB2 will decelerate a
motor to a stop instead of minimum speed. Calibrate the
deceleration time
by adjusting the opposite-direction acceleration trimpot.
RB1
STOP
RB2
RUN
Figure 12. Regenerative
Deceleration Switch
Connection
23
Regenerative brake
Short the INHIBIT terminals to regeneratively brake the motor
(see Figure 13 for INHIBIT terminal location). Reopening the
INHIBIT terminals causes the motor to accelerate to set speed.
The INHIBIT terminals bypass both the MIN SPD circuit
and the deceleration circuit. This causes the motor to stop rapidly when the INHIBIT terminals are shorted. Braking torque is
determined by the opposite-direction torque setting.
L1
FU 501
L2
FU 502
C 504
SC R 5 01
SC R 5 02
SC R 5 03
S
C 501
L1
FA ST A C TIN G
FU SE S O N LY
L2
230V
230
R 5 01
230
FU 504
SW 502
SW 501
L2
115V
115
115
T505
T501
GN D
SO 502
F1
F2
INHIBIT
Terminals
IN H - R U N
C 502
C 503
TB 501
A2
SO 501
IC 5 01
IC 5 02
A1
IN H IB IT
IN V
C 505
TB 502
P 5 01
S3
S2
S1
S0
R B 1 R B 2 - 15 + 15
T1
T2
M IN SP D
P 5 02
FW D
Figure 13. INHIBIT Terminals
24
Bison Gear & Engineering offers an accessory plug harness for
the INHIBIT terminals:
Bison®
Part Number
170-998-0100
Description
Inhibit plug with 36 in. (91 cm) wires
Twist inhibit wires and separate them from other power-carrying
wires or sources of electrical noise. Use shielded cable if the
inhibit wires are longer than 18 in. (46 cm). If shielded cable is
used, ground only one end of the shield to earth ground. Do not
ground both ends of the shield.
Coast to a stop
To coast the motor to a stop without
removing power to the drive, jumper
INHIBIT–RUN terminals 1 and 2.
To restart the motor, jumper
INHIBIT–RUN terminals 2 and 3. A
single-pole, double-throw switch may
be used as a COAST/RUN switch
(see Figure 15, page 25).
1
Each drive is assembled with
INHIBIT–RUN terminals 2 and 3
jumpered. These terminals must
be connected for the motor to run.
2
3
INHIBIT
1
2
3
RUN
Figure 14. Inhibit Run Jumper
Settings
25
COAST
TO
COAST
TOSTOP
STOP
RUN
RUN
11
22
33
SS0502
O502
COAST / RUN
SWITCH
ININH-RUN
H-RUN
L2
230V
115
T501
GND
T505
R501
FU504
230 230
SW502
SW501
L2
115V
115
2
3
SO502
F1
1
F2
IN H - R U N
C502
C503
TB 501
A2
IC 5 0 1
IC 5 0 2
A1
INHIBIT- RUN
TERMINALS
SO501
IN H IB IT
IN V
C505
TB 502
P501
S3
S2
S1
S 0 R B 1 R B 2 - 15 + 15 T1
T2
P
M IN S P D F W
Figure 15. Inhibit - Run Terminals Location
and Run / Coast Switch
26
Decelerate to zero speed
The circuit shown in Figure 16 may be used to decelerate a
motor to a zero speed. Closing the switch between S2 and S0
decelerates the motor from set speed to zero speed. The DECEL
trimpot setting determines the rate at which the drive decelerates. Set the switch to the RUN position to accelerate the motor
to set speed at a rate determined by the ACCEL trimpot setting.
REV
REV
10K
10K OHM
OHM
SPEED
SPEEDADJUST
ADJUST
POTENTIOMETER
POTENTIOMETER
S3
S3
RUN
RUN
S2
S2
DECEL
DECELTO
TO
ZEROSPEED
SPEED
ZERO
FWD
FWD
CW
CW
S1
S1
S0
S0
Figure 16. Run/Decelerate to Zero Speed Switch
(shown with bidirectional speed adjust
potentiometer connection)
27
Warning
For frequent starts and stops, use regenerative deceleration
(shorting RB1 and RB2), regenerative braking (shorting
INHIBIT terminals to each other), coasting to a stop (shorting INHIBIT–RUN terminals 1 and 2), or decelerating to
minimum speed (shorting S2 to S0). Do not use any of these
methods for emergency stopping. They may not stop a drive
that is malfunctioning.
Removing AC line power (both L1 and L2) is the only
acceptable method for emergency stopping.
CURRENT LIMIT (FWD TQ and REV TQ on regenerative
drives) is still active while the drive is regeneratively braking.
Frequent regenerative deceleration, regenerative braking, coasting to a stop, or decelerating to minimum speed produces high
torque. This may cause damage to motors, especially gearmotors
that are not properly sized for the application.
28
Calibration
Warning
Dangerous voltages exist on the drive when it is powered.
When possible, disconnect the voltage input from the drive
before adjusting the trimpots. If the trimpots must be adjusted with power applied, use insulated tools and the appropriate
personal protection equipment. BE ALERT. High voltages
can cause serious or fatal injury.
Each drive is factory calibrated to its maximum current rating.
Readjust the calibration trimpot settings to accommodate lower
current rated motors.
All adjustments increase with CW rotation, and decrease with
CCW rotation. Use a non-metallic screwdriver for calibration.
Each trimpot is identified on the printed circuit board.
29
MINIMUM SPEED (MIN SPD)
The MIN SPD trimpot setting determines the motor speed when
the speed adjust potentiometer is turned full CCW. It is factory
set to zero speed. The minimum speed feature applies only
when the drive is operating in unidirectional mode.
To calibrate, set the speed adjust potentiometer full CCW. Adjust
the MIN SPD trimpot until the motor turns at the desired minimum speed.
MAXIMUM SPEED (MAX SPD)
The MAX SPD setting determines the maximum motor speed
when the speed adjust potentiometer is turned full CW. It is factory set for maximum rated motor speed.
To calibrate, set the speed adjust potentiometer full CW. Adjust
the MAX SPD trimpot until the motor turns at the desired maximum speed.
30
FORWARD TORQUE (FWD TQ)
Warning
FWD TQ should be set to 120% of drive nameplate current
rating. Continuous operation beyond this rating may damage
the motor. If you intend to operate beyond the rating, contact
your Bison representative for assistance.
The FWD TQ trimpot setting determines the maximum torque for
accelerating and driving the motor in the forward direction. It also
sets the maximum torque for decelerating the motor in the reverse
direction. Refer to Figure 17 (page 34) for recommended FWD
TQ trimpot settings or recalibrate using the following procedure:
1. With the power disconnected from the drive, connect a DC
ammeter in series with the armature.
2. Set the FWD TQ trimpot to minimum (full CCW).
3. Set the speed adjust potentiometer to maximum forward speed.
4. Lock the motor shaft. Be sure that the motor is firmly mounted
to withstand maximum torque generated by the motor.
5. Apply line power. The motor should be stopped.
6. Slowly adjust the FWD TQ trimpot CW until the armature current is 120% of rated drive current.
7. Set the speed adjust potentiometer to minimum.
8. Remove the power from the drive and unlock the motor shaft.
9. Remove the ammeter in series with the motor armature if it is
no longer needed and re-apply power to the drive.
31
REVERSE TORQUE (REV TQ)
Warning
REV TQ should be set to 120% of drive nameplate current
rating. Continuous operation beyond this rating may damage
the motor. If you intend to operate beyond the rating, contact
your Bison representative for assistance.
The REV TQ trimpot setting determines the maximum torque for
accelerating and driving the motor in the reverse direction. It also
sets the maximum torque for decelerating the motor in the forward
direction. Refer to Figure 17 (page 34) for recommended REV TQ
trimpot settings or recalibrate using the following procedure:
1. With the power disconnected from the drive, connect a DC
ammeter in series with the armature.
2. Set the REV TQ trimpot to minimum (full CCW).
3. Set the speed adjust potentiometer to maximum reverse speed.
4. Lock the motor shaft. Be sure that the motor is firmly mounted
to withstand maximum torque generated by the motor.
5. Apply line power. The motor should be stopped.
6. Slowly adjust the REV TQ trimpot CW until the armature current is 120% of rated drive current.
7. Set the speed adjust potentiometer to minimum.
8. Remove the power from the drive and unlock the motor shaft.
9. Remove the ammeter in series with the motor armature if it is
no longer needed and re-apply power to the drive.
32
IR COMPENSATION (IR COMP)
The IR COMP trimpot setting determines the degree to which
motor speed is held constant as the motor load changes. It is
factory set for optimum motor regulation.
Recalibrate the IR COMP setting when using a lower curernt
rated motor. See Figure 17 (page 34), for typical IR COMP
trimpot settings, or recalibrate using the following procedure:
1. Set the IR COMP trimpot to minimum (full CCW).
2. Rotate the speed adjust potentiometer until the motor runs at
midspeed without load (for example, 900 RPM for an 1800
RPM motor). A hand held tachometer may be used to measure motor speed.
3. Load the motor armature to its full load armature current rating. The motor should slow down.
4. While keeping the load on the motor, rotate the IR COMP
trimpot until the motor runs at the speed measured in
step 2. If the motor oscillates (overcompensation), the IR
COMP trimpot may be set too high (CW). Turn the IR
COMP trimpot CCW to stabilize the motor.
5. Unload the motor.
33
FORWARD ACCELERATION (FWD ACC)
The FWD ACC trimpot setting determines the time the motor
takes to ramp to either a higher speed in the forward direction or
a lower speed in the reverse direction, within the limits of available torque. The FWD ACC setting is factory set for its fastest
forward acceleration time.
Turn the FWD ACC trimpot CW to increase the forward acceleration time, and CCW to decrease the forward acceleration time.
REVERSE ACCELERATION (REV ACC)
The REV ACC trimpot setting determines the time the motor
takes to ramp to either a higher speed in the reverse direction or
a lower speed in the forward direction, within the limits of available torque. The REV ACC setting is factory set for its fastest
reverse acceleration time.
Turn the REV ACC trimpot CW to increase the reverse acceleration time, and CCW to decrease the reverse acceleration time.
34
170-303-0010 / 170-343-0010
F W D TQ
TQ
FWD
F W D TQ
TQ
FWD
F W D TQ
TQ
FWD
F W D TQ
TQ
FWD
RREV
E V TQ
TQ
RREV
E V TQ
TQ
RREV
E V TQ
TQ
RREV
E V TQ
TQ
IR COMP
COMP
IR
11 HP
HP
90VDC
VDC
90
10
ADC
10 ADC
COMP
IR COMP
3/4
3/4HP
HP
90VDC
VDC
90
7.6ADC
ADC
7.6
IR COMP
COMP
1/2
1/2HP
HP
90
90VDC
VDC
ADC
55ADC
COMP
IR COMP
1/4
1/4HP
HP
90
90VDC
VDC
2.7
2.7ADC
ADC
F W D TQ
TQ
FWD
F W D TQ
TQ
FWD
F W D TQ
TQ
FWD
F W D TQ
TQ
FWD
RREV
E V TQ
TQ
RREV
E V TQ
TQ
RREV
E V TQ
TQ
RREV
E V TQ
TQ
IR
COMP
IR COMP
2 HP
HP
VDC
180 VDC
9.2
ADC
9.2 ADC
IR
COMP
IR COMP
1 HP
HP
VDC
180 VDC
5 ADC
ADC
5
IR
COMP
IR COMP
3/4
3/4HP
HP
180 VDC
VDC
ADC
3.8 ADC
IR
COMP
IR COMP
1/2
1/2HP
HP
180
180 VDC
VDC
2.5 ADC
ADC
170-303-0003 / 170-343-0003
F W D TQ
TQ
FWD
F W D TQ
TQ
FWD
F W D TQ
TQ
FWD
RREV
E V TQ
TQ
RREV
E V TQ
TQ
RREV
E V TQ
TQ
COMP
IR COMP
1/8
1/8HP
HP
90
90VDC
VDC
1.3
ADC
1.3 ADC
COMP
IR COMP
1/10
1/10HP
HP
90VDC
VDC
90
1.1
ADC
1.1 ADC
COMP
IR COMP
1/20
1/20HP
HP
90VDC
VDC
90
0.56
ADC
0.56 ADC
F W D TQ
TQ
FWD
F W D TQ
TQ
FWD
R
E V TQ
TQ
REV
RREV
E V TQ
TQ
COMP
IR COMP
1/4
HP
1/4 HP
180
VDC
180 VDC
1.4
ADC
1.4 ADC
COMP
IR COMP
1/8
HP
1/8 HP
180
180 VDC
0.67
ADC
0.67 ADC
Figure 17. Typical FWD TQ, REV TQ, and IR COMP Settings
(actual settings may vary with each application)
35
DEADBAND (DB)
The deadband trimmer potentiometer determines the time
that will elapse between the application of current in one direction before current is applied in the opposite direction.
The deadband trimmer potentiometer affects the
resistance that a motor has to changes in shaft position at
zero speed. It does this by applying AC voltage to the motor
armature.
Deadband is factory calibrated to approximately the
3 o’clock position for 60 Hz AC line operation. Recalibrate
the deadband to the 9 o’clock position for 50 Hz AC line operation. See Figure 18, for recommended deadband settings.
60 Hz
60
Hz
APPLICATIONS
Applications
D
B
DB
50 Hz
Hz
50
APPLICATIONS
Applications
DB
DB
Figure 18. Deadband Settings
36
TACHOGENERATOR (TACH)
Calibrate the TACH setting only when a tachogenerator is used.
The TACH setting, like the IR COMP setting, determines the
degree to which motor speed is held constant as the motor load
changes.
To calibrate the TACH trimpot:
1. Remove power from the drive.
2. Rotate the TACH trimmer pot to full clockwise (full CW),
3. Rotate the MAX SPD trimmer pot to full counterclockwise
(full CCW).
4. Rotate the IR COMP trimmer pot to full CCW.
5. Place the feedback selector switch (SW504) to the ARMATURE (ARM) position.
6. Rotate the main speed potentiometer to midrange.
7. Wire the DC tach to the drive. Note: The polarity of the
Tach voltage input to the drive should be T1 (+) and T2 (-).
This polarity may be measured with a DC voltmeter. If the
polarity is incorrect, swap the two tach input leads to the T1
and T2 terminals on TB502.
8. Apply power to the drive. The motor should be running at
minimum speed.
9. Rotate the main speed potentiometer to full speed in the forward direction.
10. Turn the maximum speed trimmer pot clockwise until the
desired maximum speed is reached.
11. Remove all power from the drive. The motor should stop.
12. Place the Feedback selector switch (SW504) to the
Tachogenerator (TACH) position.
37
13. Apply power to the drive. The motor should run in the forward direction.
14. Rotate the TACH trimmer pot CCW so that the maximum
speed is reached. this is the same speed as was obtained in
step 10.
15. Rotate the main speed potentiometer to the reverse direction
(S2 should be negative with respect to S1). The motor
speed should follow the speed potentiometer position.
Check that the tachogenerator is properly calibrated. The motor
should run at the same set speed when SW504 is set to either
armature or tachogenerator feedback
38
Application Notes
Connection to other Bison devices
TB502
S2
TB501
2
REGENERATIVE
DRIVE
170-993-0200
SIGNAL ISOLATOR
RB1
1
Figure 19. Connections to 170-993-0200
39
Optional speed adjust potentiometer connections
Forward-Reverse Switch
Use a single-pole, two-position switch with a single
speed adjust potentiometer to
plug reverse the motor
(Figure 20). The MIN SPD
setting is in effect for either
direction.
S0
S1
10K
OHM
S2
REV
CW
S3
FWD
Figure 20. Forward-Reverse Switch
Forward-Stop-Reverse Switch
Use a single-pole, three-position switch with a single
speed adjust potentiometer to
stop a motor between reversals (Figure 21). Set the
switch to the center position
to decelerate the motor to a
stop.
S0
S1
10K
OHM
S2
S3
REV
STOP
FWD
Figure 21. Forward-Stop-Reverse Switch
CW
40
Independent Adjustable Speeds (Forward
Direction Only)
Connect two speed adjust potentiometers with a single-pole twoposition switch to select between two independent speeds shown
in the forward direction (Figure 22). The speed adjust potentiometers can be mounted at two separate operating stations.
S0
S1
SPEED 1
P1
20K OHM
P2
20K OHM
CW
CW
S2
SPEED 2
Figure 22. Independent Adjustable Speeds
(Forward Direction)
41
Independent Forward and Reverse Speeds
Connect two speed adjust potentiometers as shown in Figure 23
to select between independent forward and reverse speeds.
S0
FWD
10K OHM
S1
FORWARD
CW
REV
10K OHM
CW
S2
REVERSE
S3
Figure 23. Independent Forward and Reverse Speeds
42
Independent Forward and Reverse Speeds
with FWD-STOP-REV Switch
Use a single-pole, three-position switch to stop the motor when
the switch is in the center position (Figure 24).
S0
S1
S2
S3
FORWARD
FWD
10K OHM
REV
10K OHM
CW
CW
STOP
REVERSE
Figure 24. Independent Forward and Reverse Speeds with a
Forward-Stop-Reverse Switch
43
Troubleshooting
Warning
Dangerous voltages exist on the drive when it is powered.
When possible, disconnect the drive while troubleshooting.
High voltages can cause serious or fatal injury.
Check the following steps before proceeding:
1. The AC line voltage must match the voltage on the drive
nameplate.
2. On dual voltage drives, check that the voltage switches are
set to the correct position.
3. The deadband (DB) must be set approximately at the
3 o’clock position for 60 Hz AC line frequency or at
9 o’clock for 50 Hz AC line frequency.
4. The motor must be rated for the drive’s rated armature
(all motors) and field outputs (shunt wound motors only).
5. Do not make any connections to F1 and F2 if using a permanent magnet motor.
6. Terminal block connections should be consistent with the
connections shown in this manual.
7. Check that line fuse FU501 (and FU502 for 230 VAC line
voltage) is properly sized and not blown.
8. Check that field fuse FU503 is 1.5 A and not blown.
44
Line fuse blows
1. Disconnect AC line voltage from the drive.
2. Check that the motor cable and armature is not shorted or
grounded.
a. The motor’s armature resistance should measure approximately 1 to 100 ohms, depending on motor horsepower.
b. A resistance reading from the motor frame to either
armature side should show open when an ohmmeter is
used on its high resistance scale.
3. Check that the field circuit is not open.
45
Motor pulsates or surges under load
1. Readjust the IR COMP setting slightly CCW until the motor
speed is stabilized.
2. Verify that the motor is not going in and out of current limit.
If so, re-adjust FWD TQ and REV TQ pots.
Line fuse does not blow, but the motor does not run
1. Verify that the speed adjust potentiometer is not set to its zero
speed position. If in voltage follower mode, verify that reference voltage is not set to zero.
2. Check the speed adjust potentiometer for continuity.
3. Verify that the inhibit pins are not shorted together.
4. Check that INHIBIT–RUN terminals 2 and 3 are connected.
5. Verify that the drive is receiving AC line voltage.
6. Check that the drive is not in current limit. If the drive is in
current limit, verify that the motor is not jammed. It may be
necessary to increase the FWD TQ or REV TQ setting if it is
set lower than the current rating of the motor.
7. Check that the speed adjust potentiometer connections to the
terminal block are correct and not open.
Motor runs too fast at the maximum speed setting
1. Check that the MIN SPD and MAX SPD setting are not set
too high.
2. Check that the field output connections are secure if you are
using a shunt wound motor.
46
Motor will not reach the desired speed
1. Check the MAX SPD setting and increase if necessary.
2. Check that the IR COMP setting is not set too low.
3. Check that the motor is not overloaded.
For additional assistance, contact your local Bison® distributor, or
the factory direct at:
PHONE: 1-800-AT-BISON
47
Factory Prewired Connections
(for Cased Drives)
1
2
3
WHITE/BLACK
WHITE
L2 (230)
BLACK
POWER
LIGHT
BLACK
BLACK
BLACK/WHITE
L1
WHITE/BLACK
L2 (115)
Figure 25. Prewired Connections to L1, L2(115) and L2(230)
48
S0
S0
GREY
grey
GREY/WHITE
grey/white
FWD
FW
D
S1
S1
S2
S2
green
GREEN
REV
REV
blue/
BLUE/
white
WHITE
BBRAKE
RAKE
CW
C
W
10K
10K
OHMW
BLUE
blue
S3
S3
Figure 26. Prewired Speed Adjust Potentiometer Connections
49
Certificate of Compliance
Bison Gear & Engineering hereby certifies that the series of drives
covered in this manual have been approved to bear the “CE” mark
provided the conditions of approval (listed in Exhibit “A”) have
been met by the end user.
This series has been tested to the following test specifications:
EN55011:1991 (emissions), and EN50082-1:1992 (immunity).
Compliance allows this series to bear the CE mark.
The end user, as described herein, falls into one of two categories:
1. The Consumer will deploy a stand-alone unit as an integral, yet external, portion of the machine he/she is operating.
2. The Original Equipment Manufacturer (OEM) will implement the product as a component of the machine being
manufactured.
50
Exhibit “A”
In addition to EMI/RFI safeguards inherent in this series’ design,
external filtering is required.
Bison requires the Corcom® filters listed in Table 3. If the exact filter is not available, the specifications are as follows:
L = 1.8 milliHenries.
C = 0.01 microFarad (Line to Ground); 1.1 microFarads (Line
to Line).
Discharge Resistor = 330Kohms.
Rated current: 1.4 times maximum DC motor current.
Filter type: Balanced 2-section.
Table 3. Corcom® Filters
Nameplate Current of
Motor Wired to the Drive
0 to 4 amps
4.1 to 13 amps
Corcom® Filter Part Number
6VV1
20VV1
The filters in Table 3 should be wired to the AC line within 0.25
meters of the drive. The ground connection from the filter must be
wired to solid earth ground (resistance less than 500 ohms); not
machine ground. This is very important!
If the end-user is using a CE-approved motor, the correct filter
from Table 3 is all that is necessary to meet the EMC directives
listed herein.
51
The end user must use the filtration listed in Exhibit A to comply
with CE. The OEM may choose to provide alternative filtering that
encompasses the Bison drive and other electronics within the
same panel.
The OEM has this liberty because CE is a machinery directive.
Whether or not every component in the OEM’s machinery meets
CE, the OEM must still submit his machine for CE approval. meet
CE, the machine will not necessarily meet CE as a machine.
Thus, no component must necessarily meet CE within the
machine, as long as the OEM takes the necessary steps to guarantee the machine does meet CE. By the same token, even if
every component in the OEM’s machine does meet CE, the
machine will not necessarily meet CE as a machine.
Use of CE-approved wiring practices, such as proper shielding,
and the filters listed in Exhibit A guarantee the drive will meet
EN55011 (1991 emissions standard) and EN50082-1 (1992 immunity standard).
52
Bison Warranty Policy
The Company warrants to the Buyer the products sold hereunder to be free
of defects in material and workmanship under normal use and service for a
period of one (1) year from the date of shipment. The obligation of the
Company under this warranty is limited to repair or replacing at its option,
any part or parts, which upon examination shall disclose to the reasonable
satisfaction of the Company to have been defective in material or workmanship. Buyer must return the products to the Company’s factory, shipping
charges prepaid, and with complete information as to alleged defects and
the installation, operation and service of the products. Except as otherwise
expressly stated herein the Company makes no representation of warranty
of any kind, express or implied, as to merchantability, fitness for a particular
purpose, or any other matter with respect to the products sold hereunder.
Bison Gear & Engineering Corp.
3850 Ohio Ave. -- St. Charles, IL 60174
Phone: 1-800-AT-BISON
www.bisongear.com
Document Number: 250-0416; Revision 0 -- May 2006
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement