Newport Brass 9451-1/07 Fairfield 3-Hole Bridge Kitchen Faucet Installation instructions

Add to My manuals
4 Pages

advertisement

Newport Brass 9451-1/07 Fairfield 3-Hole Bridge Kitchen Faucet Installation instructions | Manualzz

INSTALLATION INSTRUCTIONS

KITCHEN BRIDGE FAUCET

WITH SIDE SPRAY

Model No's: 9451-1

Congratulations on the purchase of this Newport Brass product, an excellent choice, that will give you years of quality service and enhance the look and style of your home.

Recommended Installation by a Professional Plumbing Contractor

Note: The use of petroleum base plumbers putty on our products will nullify the warranty.

We recommend the use of clear silicone sealing materials. Use plumbers tape or equivalent to seal all threaded joints. If mounting faucet to a stainless steel rim, an under-mounting support, (e.g. wood, appropriate size x 1/2” thick), should be utilized.

Recommended deck hole Ø1.25. Drill holes in mounting surface, center spacing for bridge faucet to be between 8” - 9-11/16” and the side spray hole to be a minimum of 4-3/4” away from the nearest mounting hole of faucet.

1. Place bridge faucet body through holes on mounting surface and secure into place with flange nuts. See Fig. 1 .

2. Thread quick connect adapter, with o-ring inserted, onto the base of each shank. See Fig. 1 .

3. Attach the diverter assembly to quick connect adapters - one side at a time (cold block to the cold side of faucet) as follows: Reference Fig. 2 a. Engage stem connector on to broached stem extention, located inside shank. See

Detail A.

b. Rotate to align exterior hex of upper and lower adapters and mate together so there is NO GAP between the two. See Detail B.

c. Check the alignment of the clip groove of upper adapter and the side slots of lower adapter. Secure position by pushing clips though slot and into groove. See Fig. 2 .

4. Place the side spray escutcheon with shank through mounting surface and secure into place with mounting kit . See Fig. 3 .

5. Drop side spray hose through escutcheon and thread onto diverter assembly. See Fig. 3.

6. Attach hot and cold water supply hoses (1/2-14NPS, not included) to appropriate valve . See

Fig. 4.

7. Adjust handle alignment as required by, removing set screws on handle base. Lift handle from stem, rotate to proper alignment and lower back onto stem. Secure into place with setscrews.

8. Remove aerator from spout, turn on water supply, and flush valves until water is clear. Check for leaks and make any final adjustments required. Re-attach aerator to the spout.

Important:

1. If the cold block of the diverter assembly is installed on the hot side of the faucet, the faucet will have no flow.

2. Faucet can operate without side spray by replacing the side spray connection to cold block with 1/4-18 NPMS or 1/4-18 NPT thread cap.

NWP-9451-1

REV B

Bridge faucet assembly

Detail A

Stem extention

Stem connection

Align hex-sides

(No gap between)

Detail B

NO

GAP

8” - 9-11/16”

4-3/4” min.

Shank

Clip groove

Clip

Slot

Diverter assembly

Flange nut

Quick connect adapter w/ o-ring

Figure 1

Escutcheon / shank

Side spray / hose

Figure 2

Cold block

NWP-9451-1

REV C

Figure 3

Mounting

Kit

Hot water supply

1/2-14NPS

(Not included)

Cold side

Cold water supply

1/2-14NPS

(Not included)

Figure 4

Adjust Handle Alignment:

1. In Figure 5 , ensure cartridges in full closed position and check HANDLE alignment. If the

HANDLE is not correctly aligned, temporary remove the HANDLE, loosen up (but do not completely remove) the ADAPTER SCREW and rotate CARTRIDGE ADAPTER one tooth clockwise (18 degrees), reassemble the HANDLE and recheck alignment. Repeat until the

HANDLE is aligned.

2. Remove the HANDLE and tighten the ADAPTER SCREW to firmly secure the CARTRIDGE

ADAPTER to cartridge. Reattach the HANDLE to the CARTRIDGE ADAPTER and secure the

HANDLE in place with set screw(s).

Note: When reattaching the HANDLE, assure a small gap between HANDLE and BONNET to prevent from metal-to-metal contact.

NWP-9451-1

REV C

Figure 5

2001 CARNEGIE AVE, SANTA ANA CA 92705

(949) 417-5207

WWW.NEWPORTBRASS.COM

01/07/2019

advertisement

Related manuals

Download PDF

advertisement