DXV D35105100RB.100 Percy Single Handle Monoblock Bathroom Sink Faucet Installation instructions

Add to My manuals
8 Pages

advertisement

DXV D35105100RB.100 Percy Single Handle Monoblock Bathroom Sink Faucet Installation instructions | Manualzz

INSTALLATION INSTRUCTIONS

Percy

®

Single Control Lavatory and Vessel Faucet

Loop Handle Lavatory

Models D35105104, D35105104RB

Pixie Handle Lavatory

Models D35105100 , D35105100RB

Loop Handle Vessel

Models D35105154, D35105154RB

Pixie Handle Vessel

Models D35105150, D35105150RB

Thank you for selecting DXV. To ensure that your installation proceeds smoothly, please read these instructions carefully before you begin.

RECOMMENDED TOOLS AND MATERIALS

Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing supply stores. It is essential that the tools and materials be on hand before work is begun.

14-1/8"

(359 mm)

Flat Blade Screwdriver

ROUGHING-IN DIMENSIONS:

• For reference

14-7/8"

(378 mm)

6-3/4"

(171 mm)

Channel Locks

4-1/2"

(114 mm)

8-15/16"

(227 mm)

2-1/4"

(57 mm)

2-1/4"

(57 mm)

NOTE: MOUNTING HOLE 1-1/4" (32 mm) D.

In the United States:

DXV

One Centennial Avenue

Piscataway, New Jersey 08855

Attention: Director of Customer Care

For residents of the United States, warranty information may also be obtained by calling the following toll free number: (800) 227-2734 www.DXV.com

Product names listed herein are trademarks of AS America, Inc.

© AS America, Inc. 2017

In Canada:

DXV

5900 Avebury Road

Mississauga, Ontario

L5R 3M3

Canada

Toll Free: 1-800-387-0369

Local: 905-306-1093

Fax: 1-800-395-1498 www.DXV.ca

- 1 -

Adjustable Wrench

6-3/4"

(171 mm)

4-1/2"

(114 mm) 3-5/8"

(92 mm)

8-13/16"

(223 mm)

PIXIE

HANDLE

9-9/16"

(243 mm)

1-1/2"

(38 mm) MAX.

2"

(51 mm) MAX.

12-1/2"

(318 mm)

1-1/4" OD

(32 mm OD)

SUPPLY CONNECTIONS ARE 3/8" COMPRESSION

2-7/16"

(63 mm) D.

LOOP

HANDLE

MOUNTING

SURFACE

20"

(508mm)

FLEXIBLE

HOSES

In Mexico:

DXV

Via Morelos 330

Col. Santa Clara Coatitla

Ecatepec, Estado de México 55540

Toll Free: 01-800-8391200 www.DXV.mx

M965530 Rev. 1.5 (10/17)

1

INSTALL FAUCET

CAUTION

• Seat O-RING SEAL (1) into under side of FAUCET BASE (2) .

• Feed FAUCET SUPPLIES (3) , MOUNTING STUD (4) and DRAIN CABLE ASSEMBLY (8) through the mounting hole of lavatory or mounting surface. Fig. A.

• From below, push GASKET (7) and RETAINING WASHER (5) onto MOUNTING STUD (4) . Secure Faucet with MOUNTING

NUT (6), pulling faucet to front of sink, so SUPPLIES (3) rests against mounting hole. Before final tightening, make sure collar on MOUNTING NUT (6) is seated into RETAINING WASHER (5) .

Fig. B.

• Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6) to complete faucet mounting.

Fig.

B.

COLLAR ON

MOUNTING NUT

7

5

6

4

Fig.

A.

2

GROOVE

(FAUCET BASE)

4

MOUNTING SURFACE

8

1

3

- 2 -

M965530 Rev. 1.5 (10/17)

2

POP-UP DRAIN

• Remove CLEAR PLASTIC COVER (1) . Fig. A.

• Remove FOAM SPACER (2) from under DRAIN POP-UP (3) . Fig. A.

• Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B.

Fig.

A.

1

3

2

Fig.

B.

DRAIN

BODY

4

3

REMOVE MOUNTING WASHERS

AND LOCKNUT

• Thread LOCKNUT (1) counter-clockwise and remove from drain body. Remove

PLASTIC WASHER (2) and pull off

RUBBER CONE WASHER (3) Fig. A.

• Drop DRAIN BODY (4) through sink drain

hole. Make sure WHITE FOAM GASKET (5)

is under flange of DRAIN BODY (4) . Fig. B.

Note: No plumber’s putty or caulk is required.

• The CABLE ATTACHMENT POINT (6) must

face towards the rear of the SINK. Fig. B.

Fig.

A.

3

2

1

Fig.

B.

5

REAR OF

SINK

4

6

4

ATTACH DRAIN FROM

BELOW FIXTURE

• From under side of SINK install

RUBBER CONE WASHER (3) ,

PLASTIC WASHER (2) and

LOCKNUT (1) onto DRAINBODY (4) .

Note: The CABLE ATTACHMENT

POINT (5) must face towards the rear of the SINK.

4

3

2

1

5

5

SINK

DRAIN

HOLE

TIGHTEN LOCKNUT

• Tighten LOCKNUT (1) firmly with

Adjustable Wrench or Channel Locks.

6

FLANGE GASKET AND POP-UP KNOB

• Check DRAIN FLANGE in SINK to ensure that

WHITE FOAM GASKET (3) is fully compressed and not visible. Fig. A .

• POP-UP KNOB (1) must be fully down. Fig. B.

Fig.

A.

WHITE FOAM

GASKET

NOT VISIBLE

DRAIN

FLANGE

Fig.

B.

UP

1

DOWN

1

- 3 -

M965530 Rev. 1.5 (10/17)

7

ATTACH CABLE CONNECTOR

• Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A.

• Your new POP-UP DRAIN installation is now complete. Fig. B.

Note: Tailpeice on pop-up drain is

1-1/4" (32 mm) O.D. Fig. B.

Fig.

A.

1

Fig.

B.

2

1-1/4” O.D.

8

CHECK OPERATION OF POP-UP

• Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes.

Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.

1

2

9

MAKE WATER SUPPLY AND WASTE CONNECTIONS

• Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.

Connection on fitting supplies are 3/8" (10 mm) compression. Connect

SUPPLY SUPPLY (1) (Marked with a Red Band) to the Hot wall valve and SUPPLY HOSE (2) (Marked with a Blue Band) to the

Cold wall valve.

• Faucet supplies are 20” long from faucet base.

Note: If additional supply length is required, installer must purchase additional parts separately.

Important: If SUPPLY HOSES (1, 2 ) are to long, loop as illustrated to avoid kinking.

• Connect 1-1/4" O.D. (32 mm) tailpiece on POP-UP DRAIN to waste outlet.

APPROX.

20" (508 mm )

1

- 4 -

1

HOT

2

3/8" COMPRESSION

COLD

M965530 Rev. 1.5 (10/17)

10

TEST INSTALLED FITTING

• With HANDLE

(1)

in OFF position, remove AERATOR (3) . Turn on WATER SUPPLIES (2) and check all connections for leaks.

• Operate HANDLE

(1)

to flush water lines thoroughly. Replace AERATOR

(3)

.

CHECK DRAIN CONNECTIONS

• Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains

water in sink. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting section in these instructions.

• Release POP-UP KNOB (4) down and check all drain connections and “P” trap for leaks. Tighten if necessary.

ON

1

OFF

COLD

HOT

4

3

5

WASTE

OUTLET

2

2

“P” TRAP

11

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A

CLOTH WITH A COARSE SURFACE.

- 5 -

M965530 Rev. 1.5 (10/17)

Speed Connect ® Drain

Troubleshooting Guide

If sink does not hold water even though Stopper is in the “down” position:

• Follow CABLE ADJUSTMENT PROCEDURE.

If Stopper does not raise up fully or sink drains too slowly:

• Follow CABLE ADJUSTMENT PROCEDURE.

If you need to remove the Stopper:

• Follow STOPPER REMOVAL PROCEDURE.

If you would like the ability to remove your Stopper simply by lifting it out of the drain:

• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode .

CABLE ADJUSTMENT PROCEDURE

• Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.

• Look at the area on the Drain Body where the Cable was attached and locate the component labeled as

“Cam” in the illustration. Fig. B.

• Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the

Stopper should be in the UP position. Fig. B, C.

• Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.

• Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the

Drain Body Connection (2) and hand-tighten. Fig. A.

Fig.

Fig.

A.

A.

1

1

RE-ATTACH

RE-ATTACH

CAM

CAM

Fig.

B.

Fig.

B.

Fig.

Fig.

C.

C.

DOWN

DOWN

1

1

CAM CAP

CAM CAP DISCONNECT

DISCONNECT

2

2

STOPPER REMOVAL PROCEDURE

• Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.

• Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig. B.

• Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain.

Fig. D.

• Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.

• The Stopper can now be removed by lifting it out of the Drain. Fig. F.

Fig.

Fig.

D.

D.

Fig.

Fig.

E.

E.

REMOVE

REMOVE

CAM

Fig.

Fig.

F.

F.

REMOVE

REMOVE

CAM CAP

- 6 -

M965530 Rev. 1.5 (10/17)

STOPPER INSTALLATION PROCEDURE

The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable).

LOCKED MODE:

• Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G.

• To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the

Sink. Rotate Stopper slightly if necessary so that the Stopper slides all the way down. Fig. G.

• Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig. J.

• Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not “snap” into place, then rotate the Cam to make sure it is fully inserted. Fig. K.

• Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in

Troubling Shooting Guide to complete installation. Stopper will be in “Locked” mode and not be removable.

UNLOCKED MODE:

• Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper.

Fig. H.

• To install the stopper in “Unlocked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the

Sink. Rotate Stopper slightly if necessary so that the Stopper slides all the way down. Fig. H.

• Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted.

Fig. J.

• Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not “snap” into place, then rotate the Cam to make sure it is fully inserted. Fig. K.

• Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in

“Troublingshooting Guide” to complete installation. Stopper will be in “Unlocked” mode and removable.

LOOP TOWARD

REAR OF SINK

DRAIN

Locked Mode

(Vandal Proof)

Fig.

Fig.

LOOP TOWARD

FRONT OF SINK

DRAIN

G.

H.

Unlocked Mode

Fig.

J.

INSTALL CAM

CAM

Fig.

K.

INSTALL

CAM CAP

- 7 -

M965530 Rev. 1.5 (10/17)

M964631-YYY0A

LOOP HANDLE KIT

(D35105104, D35105154)

M964633-0070A

CARTRIDGE KIT

M964634-0070A

MANIFOLD SEAL KIT

M964635-YYY0A

LIFT KNOB & ROD

(MONOBLOCK)

M964637-YYY0A

LIFT KNOB & ROD

(VESSEL)

M964712-0070A

O-RING SEAL

M964638-0070A

MOUNTING KIT

M952430-0070A

SPPED CONNECT

ASSEMBLY

®

M921935-0070A

ADAPTOR

- 8 -

Percy

®

Single Lever Lavatory and Vessel Faucets

MODEL NUMBERS

Lavatory

Loop Handle

D35105104, D35105104RB

Pixie Handle

D35105100, D35105100RB

Vessel

Loop Handle

D35105154, D35105154RB

Pixie Handle

D35105150, D35105150RB

Replace the “YYY” with appropriate finish code

POLISHED CHROME

BRUSHED NICKEL

100

144

M964632-YYY0A

PIXIE HANDLE KIT

(D35105100, D35105150)

M964636-0070A

AERATOR KIT

874214.XXX

DRAIN ASSEMBLY

M965530 Rev. 1.5 (10/17)

advertisement

Related manuals

Download PDF

advertisement