Haws 8356WCDD Axion® Recessed Pull-Down Eye Wash User guide

Add to My manuals
5 Pages

advertisement

Haws 8356WCDD Axion® Recessed Pull-Down Eye Wash User guide | Manualzz

Model 8356WCDD

Pull-Down Shower Eye/Face Wash

NOTE TO INSTALLER: Please leave this information with the Maintenance Department.

INSTALLATION, OPERATION

&

MAINTENANCE INSTRUCTIONS

1455 Kleppe Lane

Sparks, NV 89431-6467

(775) 359-4712

Fax (775) 359-7424

E-mail: [email protected]

website: www.hawsco.com

No. 2080154(7)

LIMITED WARRANTY

HAWS warrants that this specific product is guaranteed against defective material or poor workmanship for a period of one year from date of shipment . HAWS liability under this warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any goods, or part thereof, which shall appear to the Company upon inspection to be of defective material or not of first class workmanship, provided that claim is made in writing to Haws within a reasonable period after receipt of the product. Where claims for defects are made, the defective part or parts shall be delivered to the Company, prepaid, for inspection. HAWS will not be liable for the cost of repairs, alterations or replacements, or for any expense connected therewith made by the owner or his agents, except upon written authority from

HAWS, Sparks, Nevada. HAWS will not be liable for any damages caused by defective materials or poor workmanship, except for replacements, as provided above. Buyer agrees that Haws has made no other warranties either expressed or implied in addition to those above stated, except that of title with respect to any of the products or equipment sold hereunder and that HAWS shall not be liable for general, special, or consequential damages claimed to arise under the contract of sale.

The emergency equipment manufactured by HAWS is warranted to function if installation and maintenance instructions provided are adhered to. The units also must be used for the purpose for which they were intended. This product is intended to supplement first-aid treatment. Due to widely varying conditions, Haws cannot guarantee that the use of this emergency equipment will prevent serious injury or the aggravation of existing or prior injuries.

NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED, PROVIDED

OR GIVEN BY HAWS.

SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS

MODEL PLEASE CALL:

TECHNICAL SUPPORT:

1-800-766-5612

FOR CUSTOMER SERVICE:

1-888-640-4297

11/17 Model 8356WCDD Page 1 of 5

RECOMMENDED TOOLS: Adjustable wrench, pipe wrench, pipe joint sealant, Phillips screw driver, ¼” hex key wrench.

LOCATION OF UNIT: The Model 8356WCDD eye/face wash should be installed in close proximity to potential accident areas. It should be clearly identified free from obstructions and easy to access. See ANSI Z358.1 guidelines for more information.

SUPPLY LINE: The minimum recommended line size is 1" IPS with 30-90 psi (2-6 ATM) flowing pressure at supply inlet. Where sediment or mineral content is a problem, an inlet filter is recommended.

PLUMBING CONNECTIONS: Inlet supply is male 1" IPS; waste is 2” IPS.

INSTALLATION PROCEDURE

Refer to installation drawing for clarification. Check Parts List to ensure all required parts are included.

1. Install all items at dimensions shown in installation drawing.

2. Once valve assembly is installed, install mounting frame(s) over valve assembly.

3. IMPORTANT: Showerhead must be positioned in-line with eye/face wash to allow for simultaneous use by the same user per ANSI Z358.1.

4. Install remaining items to dimensions shown.

5. Each unit is factory preset to meet the 5 pound (22.2 N) maximum activation force requirement for disabled persons. If adjustment is required after installation, follow the adjustment directions below. a) Locate the two ball detents, one on each side of the eyewash tray. See installation drawing. b) Using a flat screwdriver, adjust each ball detent to make slight contact with the eyewash housing just before the ball detent snaps into its locating position on the housing. c) Once both ball detents are adjusted as above, tighten each ball detent ¼ turn. d) Using a force gauge, ensure the force required to open the eyewash unit does not exceed 5 pounds (22.2 N).

CLEANING INSTRUCTIONS FOR STAINLESS BEAD-BLASTED PRODUCTS

Haws recommended cleaning procedure for stainless bead blasted products is as follows:

1. Use a stainless steel polish and cleaner for removing stains and finger prints.

2. Spray cleaner onto stainless surfaces and wipe dry with clean cloth. Cleaned surface will resist new stains and fingerprints.

11/17 Model 8356WCDD Page 2 of 5

MODEL PACKAGE

8356WCDD

INCLUDED PARTS

QUANTITY

1

1

1

1

1

1

1

1

1

1

1

ITEMS INCLUDED

Mounting Frame/Eyewash assembly

Valve assembly

Handle/screw assembly

Showerhead

Drain assembly

Escutcheon

1” x 5” Nipple

1” X 22” Nipple

1” Elbow

Emergency Eyewash/shower sign

Test Tag

PROBLEM

1. No flow.

TROUBLESHOOTING

REPAIR CHECKLIST

1. Check the main shut-off valve.

2. Insufficient water flow at eye/face wash.

2a. Verify minimum 30 psi (2 ATM) flowing supply line pressure.

b. Probable clogging of flow control due to inadequate line flushing. Unscrew eye/face wash head and remove the four screws to disassemble the head, clean the flow control and reassemble head. c.

Remove cap located on in-line strainer housing using a ¼” Allen wrench to access and clean filter screen. See installation drawing for location.

3a. Possible blocked flow control, see above solution.

3. Eye/face wash streams do not meet desired eye level.

5. Tray too hard to open or does not stay closed.

b. Possible non-leveled eye/face wash assembly.

4. Insufficient water flow at the showerhead, however, eye/face wash is sufficient.

c. Possible low supply pressure.

4.

Probable clogging of flow control inside showerhead. Remove showerhead by unscrewing it and clean rubber flow control.

5.

See “Installation Procedure” Step 5.

For more information about Haws Products, see our website: www.hawsco.com

.

© 2017 Haws

®

Corporation – All Rights Reserved

HAWS ® and other trademarks used in these materials are the exclusive property of Haws Corporation.

11/17 Model 8356WCDD Page 3 of 5

THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS

MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.

ITEM

5

6

3

4

1

2

7

DESCRIPTION

TEST TAG

SHOWER/EYEWASH SIGN

SHOWER HEAD

1" IPS SHOWER BALL VALVE

FLOW CONTROL

EYE/FACE WASH

VALVE REPAIR KIT

PART NO.

SP170

SP178

SP829SS

0006575900

0003138392.3

SP65PD

VRK 7650

3 5

7

6

2

4

1

C

WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.

PARTS BREAKDOWN

ECN NO.

4290

REVISED PER

ECN: 5242

BY

VWC

DRAWN DATE

I.ROBERTS

7/12/10

APPROVED

FV

DATE

CHKD

VWC

11/23/17

MODEL(S)

SCALE:

1455 KLEPPE LANE

SPARKS, NEVADA 89431

(775) 359-4712 FAX (775) 359-7424

E-MAIL: [email protected]

WEBSITE: WWW.HAWSCO.COM

PULLDOWN SHOWER EYE/FACE WASH

NA DRAWING TYPE:

8356WCDD

PARTS BREAKDOWN SIZE: A

PART NUMBER

0002080154

REVISION

SHEET 1

7

OF 1

PAGE 4 OF 5

THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS

MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.

(NOT SUPPLIED)

OPTIONAL SHOWER HEAD

HANGER BRACKET

INSTALLATION

SUSPENDED

CEILING

NOTES:

1. WHEN INSTALLING THIS UNIT, LOCAL , STATE, OR FEDERAL CODES SHOULD BE ADHERED TO FOR INSTALLATION DIMENSIONS (LOCATIONS),

WASTE AND SUPPLY REQUIREMENTS OTHER THAN SHOWN.

2. TO COMPLY WITH ANSI Z358.1-2014 FOR EMERGENCY EYEWASH OR EYE/FACE WASH:

EYEWASH OR EYE/FACE WASH SHALL BE POSITIONED SUCH THAT FLUSHING FLUID PATTERN IS NOT LESS THAN 33" (838mm), NO GREATER

THAN 53" (1346mm) FROM SURFACE ON WHICH USER STANDS,AND 6.0" (153mm) MINIMUM FROM WALL OR NEAREST OBSTRUCTION.

3 SHOWER MUST BE POSITIONED IN-LINE WITH EYE/FACEWASH HEAD TO ALLOW FOR SIMULTANEOUS USE BY THE SAME USER PER ANSI Z358.1.

4 MOUNTING HARDWARE NOT SUPPLIED.

5. DIMENSIONS MAY VARY BY ±1/2" (13 mm).

1 X 5" GALV NIPPLE

(SUPPLIED)

(9-1/2") (241mm)

10"

254mm

ESCUTCHEON

(SUPPLIED)

1 X 22" S.S. NIPPLE

(SUPPLIED)

3 STAINLESS STEEL

SHOWER HEAD

WITH 20 GPM

FLOW CONTROL

EYE/FACE WASH "PANIC BAR"

(SHOWN IN OFF POSITION-

PULL DOWN TO ACTIVATE)

4X 4-1/2"

114mm

32"

813mm

2-11/16"

68mm

4"

102mm

SEE DETAIL "A"

Ø 10-1/2"

267mm

FLANGE 34"

864mm

RECOMMENDED

22"

559mm

11"

23-5/16"

592mm

6X Ø3/16" 4

4.8mm

MOUNTING

HOLE

1" IPS BRASS

STAY OPEN

BALL VALVE

WITH INLET

AND OUTLET

UNION

82"-96"

2083mm-2438mm

1" IPS

FEMALE

SUPPLY

INLET

IN-LINE STRAINER

HOUSING

REMOVABLE

ACCESS PANELS

(NOT SHOWN)

1-1/2" OD

DRAIN TAILPIECE

EXTERNAL

DRAIN COVER

EYE/FACE WASH

(SHOWN IN ON

POSITION)

(46")

(1168mm)

33"-53"

838mm-1346mm

FLOW PATTERN

(34-5/8")

(879mm)

2X

BALL

DETENT

FLOOR LINE

SHOWER "PANIC BAR"

IN OFF POSITION

PULL DOWN TO

ACTIVATE SHOWER

(29-5/8")

(752mm)

18-3/4"

476mm

1"

25mm

FLANGE

ALL AROUND

1" IPS (NOT

SUPPLIED)

3-1/2"

89 mm

(47-1/2")

(1207mm)

30-1/4"

768mm

21-7/8" (556mm)

TO FINISHED FLOOR

(BOTTOM OF

ROUGH IN)

20-1/8"

511mm

2-5/8"

67mm

1-7/8"

48mm

DETAIL "A"

ROTATED FOR CLARITY

ECN NO.

4290

REVISED PER

ECN: 5242

DATE:

BY:

VWC

DRAWN:

I. ROBERTS 7/12/10

APPROVED: DATE:

FV

CHK'D.:

VWC

11/23/17

MODEL(S)

SCALE: NA DRAWING TYPE:

8356WCDD

1455 KLEPPE LANE

SPARKS, NEVADA 89431

(775) 359-4712 FAX (775) 359-7424

E-MAIL: [email protected]

WEBSITE: WWW.HAWSCO.COM

INSTALLATION SIZE: A

PART NUMBER

0002080154.D

REVISION

SHEET 1

7

OF 1

C

advertisement

Related manuals

Download PDF

advertisement