Haws 7655WCSM Axion® MSR 1/2 x 1/2 User guide

Add to My manuals
4 Pages

advertisement

Haws 7655WCSM Axion® MSR 1/2 x 1/2 User guide | Manualzz

INSTALLATION, OPERATION

&

MAINTENANCE INSTRUCTIONS

1455 Kleppe Lane

Sparks, NV 89431-6467

(775) 359-4712

Fax (775) 359-7424

E-mail: [email protected]

website: www.hawsco.com

Model 7655WCSM

Eye/face Wash

No. 2080062(3)

NOTE TO INSTALLER: Please leave this information with the Maintenance Department.

LIMITED WARRANTY

HAWS ® warrants that all of its products are guaranteed against defective material or poor workmanship for a period of one year from date of shipment.

HAWS liability under this warranty shall be discharged by furnishing without charge F.O.B. HAWS Factory any goods, or part thereof, which shall appear to the Company upon inspection to be of defective material or not of first class workmanship, provided that claim is made in writing to company within a reasonable period after receipt of the product. Where claims for defects are made, the defective part or parts shall be delivered to the Company, prepaid, for inspection. HAWS will not be liable for the cost of repairs, alterations or replacements, or for any expense connected therewith made by the owner or his agents, except upon written authority from HAWS, Sparks, Nevada. HAWS will not be liable for any damages caused by defective materials or poor workmanship, except for replacements, as provided above.

Buyer agrees that Haws has made no other warranties either expressed or implied in addition to those above stated, except that of title with respect to any of the products or equipment sold hereunder and that HAWS shall not be liable for general, special, or consequential damages claimed to arise under the contract of sale.

The emergency equipment manufactured by HAWS is warranted to function if installation and maintenance instructions provided are adhered to. The units also must be used for the purpose, which they were intended. This product is intended to supplement first-aid treatment. Due to widely varying conditions HAWS cannot guarantee that the use of this emergency equipment will prevent serious injury or the aggravation of existing or prior injuries.

NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,

PROVIDED OR GIVEN BY HAWS.

SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS

MODEL PLEASE CALL:

TECHNICAL SUPPORT:

1-800-766-5612

FOR CUSTOMER SERVICE:

1-888-640-4297

10/17 Model 7655WCSM Page 1 of 4

RECOMMENDED TOOLS: Adjustable wrench, pipe wrench, pipe joint sealant, Phillips screw driver, ¼” hex key wrench.

LOCATION OF UNIT: The Model 7655WCSM eye/face wash should be installed in close proximity to potential accident areas. It should be clearly identified free from obstructions and easy to access. See ANSI Z358.1 guidelines for more information.

SUPPLY LINE: The minimum recommended line size is 1/2" IPS with 30-90 psi (2-6 ATM) flowing pressure at supply inlet. Where sediment or mineral content is a problem, an inlet filter is recommended.

PLUMBING CONNECTIONS: Inlet supply is male 1/2" IPS, no drain.

CLEANING INSTRUCTIONS FOR STAINLESS BEAD-BLASTED PRODUCTS

Haws recommended cleaning procedure for stainless bead blasted products is as follows:

1. Use a stainless steel polish and cleaner for removing stains and finger prints.

2. Spray cleaner onto stainless surfaces and wipe dry with clean cloth. Cleaned surface will resist new stains and fingerprints.

MODEL PACKAGE

7655WCSM

INCLUDED PARTS

QUANTITY

1

1

1

1

ITEMS INCLUDED

Mounting Frame/Eyewash assembly

Surface Mount Frame

Emergency Eyewash Sign

Test Tag

TROUBLESHOOTING

PROBLEM

1. No flow.

REPAIR CHECKLIST

1a. Check the main shut-off valve.

2. Insufficient water flow at eye/face wash.

3. Eye/face wash streams do not meet desired eye level.

2a. Verify minimum 30 psi (2 ATM) flowing supply line pressure.

b. Probable clogging of flow control due to inadequate line flushing. Unscrew eye/face wash head and remove the four screws to disassemble head. Clean flow control and reassemble head. c. Remove cap located on L – Strainer using a

1/4” allen wrench to access and clean filter screen.

3a. Possible blocked flow control, see above solution. b. Possible non-leveled eye/face wash assembly.

For more information about Haws Products, see our website: www.hawsco.com

.

© 2017 Haws ® Corporation – All Rights Reserved

HAWS ® and other trademarks used in these materials are the exclusive property of Haws Corporation.

10/17 Model 7655WCSM Page 2 of 4

THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS

MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.

PARTS BREAKDOWN

SP65PD

EYE/FACEWASH HEAD

VRK7650 VALVE REPAIR KIT

O-RING O-RING SEAT

SP170

TEST TAG

SP175

EYEWASH SIGN

C

WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.

ECN NO.

4290

DRAWN

I.

APPROVED

FV

REVISED PER

ECN: 5240

BY

VWC

DATE

7/13/10

CHKD

VWC

DATE

11/23/17

MODEL(S)

SCALE: NA DRAWING TYPE:

7655WCSM

.

1455 KLEPPE LANE

SPARKS, NEVADA 89431

(775) 359-4712 FAX (775) 359-7424

E-MAIL: [email protected]

WEBSITE: WWW.HAWSCO.COM

PARTS BREAKDOWN SIZE: A

PART NUMBER

0002080062

REVISION

3

SHEET 1 OF 1

PAGE 3 OF 4

THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS

MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.

14-1/2"

368mm

11-1/4"

286mm

6X Ø3/16" 3

4.8mm

MOUNTING

HOLE

32-1/2"

826mm

1/2" IPS SUPPLY

CL

PULL DOWN

VALVE WITH

EYE/FACE WASH

HEADS

IN-LINE STRAINER

6-3/4"

171mm

REMOVABLE

ACCESS PANEL

(NOT SHOWN)

2-3/16"

56mm

SUPPLY

23"

584mm

PULL DOWN

TO OPEN

EYE/FACE WASH

3-3/4"

95mm

33"- 53"

838mm-1346mm

FLOW PATTERN

(34-1/2")

(876mm)

(31-5/8")

(803mm)

21"

533mm

18-5/16"

465mm

FLOOR LINE

NOTES:

1. WHEN INSTALLING THIS UNIT, LOCAL , STATE, OR FEDERAL CODES SHOULD BE ADHERED TO FOR

INSTALLATION DIMENSIONS (LOCATIONS), WASTE AND SUPPLY REQUIREMENTS OTHER THAN SHOWN.

2. TO COMPLY WITH ANSI Z358.1-2014 FOR EMERGENCY EYEWASH OR EYE/FACE WASH:

EYEWASH OR EYE/FACE WASH SHALL BE POSITIONED SUCH THAT FLUSHING FLUID PATTERN IS

NOT LESS THAN 33" (838mm) AND NO GREATER THAN 53" (1346mm) FROM SURFACE ON WHICH

USER STANDS; AND 6.0" (153mm) MINIMUM FROM WALL OR NEAREST OBSTRUCTION.

3 MOUNTING HARDWARE NOT SUPPLIED.

4. DIMENSIONS MAY VARY BY ±1/2" (13 mm).

ECN NO.

4290

DRAWN:

REVISED PER

ECN: 5240

DATE:

I.ROBERTS

7/13/10

APPROVED:

FV

BY:

VWC

CHK'D.:

VWC

DATE:

11/23/17

MODEL(S)

SCALE: NA

C

DRAWING TYPE:

7655WCSM

.

1455 KLEPPE LANE

SPARKS, NEVADA 89431

(775) 359-4712 FAX (775) 359-7424

E-MAIL: [email protected]

WEBSITE: WWW.HAWSCO.COM

INSTALLATION SIZE: A

PART NUMBER

0002080062.D

REVISION

SHEET 1

3

OF 1

advertisement

Related manuals

Download PDF

advertisement