QuickSpec User`s Manual - QuickCheck

QuickSpec User`s Manual - QuickCheck
CUMMINS QUICKSPEC
User's Manual
Copyright © 2004
Cummins Inc.
QUICKSPEC, QuickCheck, and INLINE are trademarks of Cummins Inc.
HotSync is a registered trademark of Palm, Inc.
DISCLAIMER
QUICKSPEC SOFTWARE, REFERRED TO HEREAFTER AS COVERED CODE, IS
PROVIDED UNDER THIS LICENSE ON AN ``AS IS'' BASIS, WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
WITHOUT LIMITATION, WARRANTIES THAT THE COVERED CODE IS FREE
OF DEFECTS, MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE OR NONINFRINGING. LICENSEE BEARS THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE COVERED CODE. SHOULD ANY COVERED CODE
PROVE INEFFECTIVE IN ANY RESPECT, LICENSEE SHALL ASSUME THE
COST OF ANY NECESSARY SERVICING, REPAIR OR CORRECTION. THIS
DISCLAIMER OF WARRANTY CONSTITUTES AN ESSENTIAL PART OF THIS
LICENSE. NO USE OF ANY COVERED CODE IS AUTHORIZED HEREUNDER
EXCEPT UNDER THIS DISCLAIMER.
LICENSEE AGREES NOT TO
TRANSLATE, REVERSE ASSEMBLE, REVERSE COMPILE, ADAPT,
TRANSLATE, ALTAR, MODIFY, OR CHANGE IN ANY WAY THE LICENSED
SOFTWARE OR ANY UPDATE THERETO WITHOUT THE PRIOR WRITTEN
AUTHORIZATION OF CUMMINS. LICENSEE AGREES THAT UNDER NO
CIRCUMSTANCES SHALL LICENSOR BE RESPONSIBLE FOR ANY DAMAGES,
WHETHER DIRECT, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY OR
PUNITIVE, STEMMING FROM LOSS OF USE, DATA, PROFITS OR OTHER
LOSSES RESULTING IN WHOLE OR IN PART FROM LICENSEE’S
INSTALLATION OR USE OF THE COVERED CODE. BY ITS INSTALLATION OF
THE COVERED CODE, LICENSEE AFFIRMS ITS ACCEPTANCE OF THE ABOVE
DISCLAIMER AND RELEASES LICENSOR, ITS SUBSIDIARIES AND ITS
AFFILIATES FROM ANY AND ALL CLAIMS FOR DAMAGE STEMMING EITHER
FROM LICENSEE’S INSTALLATION OR USE OF THE COVERED CODE.
Copyright © 2004
Cummins Inc.
QUICKSPEC, QuickCheck, and INLINE are trademarks of Cummins Inc.
HotSync is a registered trademark of Palm, Inc.
QUICKSPEC User's Manual
Table of Contents
WELCOME .............................................................................................................. 4
Handheld Device Requirements .............................................................................. 4
PC Requirements ...................................................................................................... 5
INSTALLATION ......................................................................................................... 6
Software Installation ................................................................................................. 6
Adapter Installation................................................................................................... 9
APPLICATION ........................................................................................................ 10
Activating QuickSpec ............................................................................................. 10
QuickSpec Basic Navigation.................................................................................. 10
Engine Info Screen.................................................................................................. 11
Settings Screen ....................................................................................................... 11
Expansion Switches ..........................................................................................................12
Scrollbar.............................................................................................................................12
Tap and Hold Tool-tip ........................................................................................................12
Gearing Screen........................................................................................................ 12
ARCHIVING DATA TO THE PC ................................................................................. 13
BASIC TUTORIAL ................................................................................................... 14
APPENDIX A: MAINTAINING YOUR QUICKSPEC HARDWARE ..................................... 15
Datalink Cable Storage ........................................................................................... 15
Care .......................................................................................................................... 15
APPENDIX B: QUICKCHECK III KIT CONTENTS ........................................................ 16
Optional Cables for QuickCheck III: ..................................................................................16
APPENDIX C: FREQUENTLY ASKED QUESTIONS ...................................................... 17
Installation Problems.............................................................................................. 18
Hardware Problems ................................................................................................ 19
Application Problems ............................................................................................. 19
HotSync Problems .................................................................................................. 19
Beaming Problems.................................................................................................. 20
Help Desk Support Center...................................................................................... 20
APPENDIX D: CONNECTOR PIN-OUTS ..................................................................... 21
GLOSSARY ........................................................................................................... 23
INDEX ................................................................................................................... 25
Rev. 1.0
Cummins Inc.
Page 3
QUICKSPEC User's Manual
WELCOME
We thank you for purchasing the QUICKCHECK™ III datalink adapter for Cummins
diesel engine applications. It is our hope that this device, coupled with your
Palm™ handheld organizer, will add value to your already valuable Cummins
engine by giving you the ability to view trim and adjustment information quickly
and conveniently. QUICKSPEC supported engine applications include: ISM, ISM
02, ISX, ISX 02, ISB, ISB 02, ISC, ISC 03, ISL, and ISL 03.
The QUICKSPEC application uses the QUICKCHECK III datalink adapter2 to
communicate with the engine ECM (electronic control module) component on the
SAE J1587 and J1939 datalinks. It is designed to complement the existing
POWERSPEC™ tool by providing a more portable, affordable, and convenient tool
for reading Cummins engine trim and adjustment settings.
Handheld Device Requirements
QUICKSPEC is compatible with the Garmin® IQue 3600 and Palm M500™,
M505™, M515™, I705™, and Tungsten™ T, T2, C, and W handheld computing
devices. QUICKSPEC is NOT compatible with Handspring™ computing devices.
For convenience, this manual refers to all Palm computing devices as handheld
organizers, handheld devices, or simply handhelds or organizers without
including the Palm name or model.
QUICKSPEC requires version 3.5 or later of the Palm OS software for your
handheld device
To operate the QUICKCHECK III datalink adapter, your handheld organizer requires
version 3.3 or later of the Palm HotSync® synchronization technology software.
If your software is an earlier version, update it to the latest version without cost at
the Palm web site: http://www.palm.com.
2
QuickSpec is NOT compatible with the QuickCheck II datalink adapter.
Rev. 1.0
Cummins Inc.
Page 4
QUICKSPEC User's Manual
PC Requirements
These are the minimum requirements for your computer system to synchronize
with a Palm handheld organizer as listed in the Palm computing device
Handbook:
ƒ
IBM-compatible Pentium-class class computer
ƒ
Windows 98/Me/2000/XP (Windows 95/NT operating systems require
a serial cradle, sold separately)
ƒ
16 MB RAM (64 MB recommended with Windows 2000)
ƒ
30 MB available hard disk space
ƒ
VGA monitor or better (256 color video display)
ƒ
CD-ROM drive (you can also download the Palm Desktop software
from http://www.palmone.com)
ƒ
Mouse
ƒ
One USB port or available serial port with the organizer cradle plugged
in (serial cradle sold separately)
Rev. 1.0
Cummins Inc.
Page 5
QUICKSPEC User's Manual
INSTALLATION
CAUTION: Connect and operate QUICKSPEC only when the
vehicle is stationary. (The key switch must be in the on
position.)
Software Installation
The QUICKSPEC installation is a typical Windows, self-extracting installation. It
sets up the application for the handheld.
The QUICKSPEC software installation instructions are listed below. The following
steps assume that you have already installed the handheld Desktop software and
you have performed a HotSync operation with the handheld device at least once.
If you have not installed this software and performed a HotSync operation, see
the handheld handbook for instructions on installing the Desktop software.
1. Insert the QUICKSPEC CD-ROM3 into your computer.
2. Click on the Windows Start menu and select Run.
3. Type e:QSpec Setup.exe, where e: is the letter assigned to the CD-ROM
drive.
4. Click the OK button to begin the installation.
5. The Welcome window is displayed. Click on the Next button.
6. The message box below is then displayed. Select OK if you have
already installed the Palm Computing Desktop Software. If not, select
Cancel to exit the QUICKSPEC installation. After installing the Palm
Computing Desktop Software, restart the QUICKSPEC installation.
3
In the event the QSpec Setup.exe installation file was obtained by a different means (e.g., the
Internet), simply specify the source file and location in Step 3 using the Browse button, rather
than specifying the computer drive.
Rev. 1.0
Cummins Inc.
Page 6
QUICKSPEC User's Manual
7. Read the License Agreement and select Accept or Decline. If you decline
the agreement, the installation will exit.
8. Read the information displayed, then click Next.
9. The installation will now install the necessary files to the PC.
10. After the files are copied, the window below is displayed. Select your
Palm User ID from the list of registered Palm users, and then click OK.
You must select the User ID for the handheld device you want to install
the QUICKSPEC application on in order for the HotSync operation to install
the QUICKSPEC application on that handheld device. If you want to install
the QUICKSPEC software on another handheld device, the installation must
be run again.
Rev. 1.0
Cummins Inc.
Page 7
QUICKSPEC User's Manual
NOTE: If there are no user IDs listed in this window, you most likely do not have
the Palm Computing Desktop Software installed or have never HotSync’ed the
handheld device. In this case, select Cancel and exit the installation. You must
then install the Palm Computing Desktop Software, perform a HotSync operation
on the handheld device, and run the QUICKSPEC installation again.
11. Click Finish on the Installation Complete window. The installation has now
placed all needed PC components into the root directory for the handheld
device (typically C:\palm). However, QUICKSPEC components are placed
in the \qSpec directory immediately below the Palm root directory (e.g.,
C:\Palm\qSpec or C:\Program Files\Palm\qspec).
12. Perform a HotSync operation to install the QUICKSPEC application on the
handheld organizer.
Important:
Due to the amount of data required by the QUICKSPEC
application, it will take several minutes for the HotSync to install the
required databases. Please be patient during the installation process.
Rev. 1.0
Cummins Inc.
Page 8
QUICKSPEC User's Manual
Adapter Installation
The QUICKSPEC application uses only the QUICKCHECK III datalink adapter to
connect to the vehicle’s datalink. The QUICKCHECK II datalink adapter is not
compatible with the QUICKSPEC application.
The picture below illustrates how to connect the handheld device to the vehicle’s
datalink connector.
Connect to
vehicle’s datalink
connector
Handheld
Device
6-pin or 9-pin
Deutsch cable to
DB25F
Palm Universal Cable
16-pin to DB9M
6-pin P/N 3165160
9-pin P/N 3165159
P/N 3165017
QuickCheck III
Datalink Adapter
P/N 3165015
Rev. 1.0
Cummins Inc.
Page 9
QUICKSPEC User's Manual
APPLICATION
The QUICKSPEC application, in conjunction with the QUICKCHECK III datalink
adapter, allows you to read and view trim and adjustment settings on your
Cummins diesel-powered vehicle.
With QUICKSPEC, you can:
•
Read and view engine dataplate information, such as engine type, serial
number, and owner information
•
Read and view both trim and adjustment settings
•
Calculate Gearing information
Activating QuickSpec
After successfully installing the QUICKSPEC application and performing a HotSync
operation on the handheld device, the QUICKSPEC application icon depicted at the
right appears in the handheld organizer’s application launcher. Tap the icon to
launch the QUICKSPEC application.
The QUICKSPEC application checks for a vehicle on the datalink each time it is
activated. After a vehicle is detected and the information is processed, the
QUICKSPEC application must be exited and re-activated to detect another vehicle.
Exit icon in the top right-hand corner to close the application.
Tap the
QuickSpec Basic Navigation
When the QUICKSPEC application is launched, the three available data screens
are displayed in tabular form. The Engine Info screen is the default active screen
when the application is started. To view the Settings and Gearing screens, simply
tap the screen’s tab. Tapping the screen’s tab will bring that screen forward and
display the related information.
Help Button
Screen Tabs
Exit Button
Scroll Buttons
Tap the
Help About icon to display version information about the QUICKSPEC
application and adapter.
Rev. 1.0
Cummins Inc.
Page 10
QUICKSPEC User's Manual
Tap the
Exit icon to close the QUICKSPEC application.
Tap the
Scroll arrows to scroll up and down to view additional data that may
be available on the current screen.
Engine Info Screen
The Engine Info data display screen is the default active screen once the
application has completed reading the engine settings. This screen lists
a select set of parameters and their values.
Below is a complete list of the parameters displayed on the Engine Info
screen:
•
•
•
•
•
•
•
•
Engine Type
Serial Number
Engine Build Date
Owner Name
Owner Location
Last Tool to Modify the Engine Settings
PowerSpec Enabled
Vehicle Unit Number
Settings Screen
The Settings screen's primary purpose is to display engine trims and settings as
they are currently recorded on the vehicle. Due to the limited screen real estate
and large amount of data that needs to be displayed, several features exist to
ease navigation.
Scrollbar
Expansion Switches
Tap and hold tool-tip
Rev. 1.0
Cummins Inc.
Page 11
QUICKSPEC User's Manual
Expansion Switches
These buttons appear on the left-hand side of the screen and are used to
collapse and expand categories. The parameters are organized by headings
identified by all capital letters. Parameters are further subdivided into categories
which have an expansion switch.
Scrollbar
This is a standard scrollbar which is moved by a tap and hold of the slider,
followed by a vertical movement. The arrows are only for aesthetics and are not
buttons.
Tap and Hold Tool-tip
Each Column on this screen can be expanded to see more data by a tap and
hold of the row. The figure above shows an example of this feature. The
parameter Accelerator Maximum Road Speed can be seen in its entirety. This
was accomplished by tapping and holding the text in the Parameter column.
Additionally the same results can be achieved for the Value and Units columns.
As soon as the stylus is lifted from the screen, the application will revert to its
normal display status.
Gearing Screen
The Gearing screen lists a select set of parameters used to calculate engine
speed in top gear at top road speed, their value, and the units they are displayed
in.
Below is a complete list of the trip parameters displayed on the Gearing screen:
Rev. 1.0
•
Transmission Top Gear Ratio
•
Transmission Gear Down Ratio
•
Tire Revolutions Per Mile
•
Rear Axle Ratio
•
RPM at Cummins recommended Gearing
Speed
•
RPM at Road Speed Governor
Cummins Inc.
Page 12
QUICKSPEC User's Manual
ARCHIVING DATA TO THE PC
The QUICKSPEC data cannot be saved on the handheld nor transferred from the
device to a PC for longer-term storage.
Rev. 1.0
Cummins Inc.
Page 13
QUICKSPEC User's Manual
BASIC TUTORIAL
This section describes a typical data-gathering session.
It begins with
connecting to a vehicle, collecting (scanning) the data, and viewing the data on a
handheld device.
This tutorial assumes the following:
•
The handheld organizer will be connected to a vehicle that it has not been
previously connected to;
•
The user is familiar with Palm handheld organizer standard operations;
•
The QUICKSPEC cable, adapter, and handheld have been properly connected.
Step 1: Attach the 16-pin connector on the Palm Universal Cable to the bottom of the
Connecting handheld organizer. Attach the DB9 male connector on the Palm Universal
Cables Cable to the connector on the QuickCheck III Datalink Adapter labeled “To
PC/PDA”. Attach the DB25 Female connector of the Deutsch cable to the
QuickCheck III Datalink Adapter connector labeled “To Engine”. Connect the
appropriate 6-pin or 9-pin Deutsch connector to the vehicle’s datalink connector.
See the Adapter Installation section on page 9 for an illustration.
Step 2: The engine should be keyed “On”. Tap the QUICKSPEC application icon. The
Connect to QUICKSPEC application immediately attempts to connect to the datalink.
Vehicle
Step 3: When a successful connection is established, QUICKSPEC displays the message
Reading Identifying ECM in the status window. After the vehicle’s ECM has been
Data identified, the status window will display Loading Tables, then begin reading the
engine information in the following order: Reading Dataplate, Reading Features,
Reading Passwords, Reading Trims, Reading Trip Data.
Step 4: Finally, after the data has been gathered, the status window displays Generating
Generating Report. The data is then displayed on the handheld device. The information is
Report viewable by tapping on the tab labels across the top of the window. The Engine
Info screen is on top. Tap the Settings or Gearing tab labels to see the data
related to that category.
Rev. 1.0
Cummins Inc.
Page 14
QUICKSPEC User's Manual
APPENDIX A:
HARDWARE
MAINTAINING YOUR QUICKSPEC
Datalink Cable Storage
The datalink end of the cable should be disconnected from the vehicle datalink
when the adapter is not in use.
Care
Treat the datalink adapter with care, just as you do the Palm handheld organizer.
Neither is waterproof and should not be exposed to rain or moisture.
Also, like the handheld, the adapter should be protected from temperature
extremes. Do not leave it on the vehicle dashboard on a hot day and keep it
away from other heat sources, including heaters.
Rev. 1.0
Cummins Inc.
Page 15
QUICKSPEC User's Manual
APPENDIX B: QUICKCHECK III KIT CONTENTS
P/N 3165142
QuickCheck III RS-232 Kit
Kit Contents
P/N 3165015
QuickCheck III Adapter RS-232
P/N 3165159
QuickCheck 9-pin Deutsch Cable to DB25F
P/N 3165160
QuickCheck 6-pin Deutsch Cable to DB25F
P/N 3165017
Palm Universal Cable, 16-pin to DB9M
P/N 3165149
QuickCheck III Software CD-ROM:
P/N 3165143
•
QuickCheck III installation program
•
QuickTrip installation program
•
QuickSpec installation program
Storage Case
Optional Cables for QuickCheck III:
P/N 3165141
DB25F 2-pin Weather-Pack/3-pin Deutsch/Cigarette Plug
connector
P/N 3824438
DB25F 2-pin Weather-Pack/Cigarette Plug connector
P/N 3824440
DB25F 8-pin AMP connector
P/N 3162849
2-pin Weather-Pack/Cigarette Plug connector
P/N 3162851
Extension DB9F to DB9M (30.48M [100ft])
P/N 3162847
DB25F 3-pin Deutsch/2-pin Weather-Pack connector
P/N 3163096
J1939 Backbone adapter
P/N 3163597
J1939 gender changer adapter
P/N 3163646
3-pin Deutsch/3-pin Weather-Pack adapter for Dodge pickup
Rev. 1.0
Cummins Inc.
Page 16
QUICKSPEC User's Manual
APPENDIX C: FREQUENTLY ASKED QUESTIONS
Before contacting your local Cummins distributor for support, please experiment
a bit to reproduce and isolate the problem. If you find it necessary to contact
your distributor, please be ready to provide the following information:
•
The version of the Windows operating system you are using on your PC
•
The actual error message or state that you are experiencing
•
The steps you take to reproduce the problem
•
The version of organizer software you are using and available memory
•
The version of QuickSpec software you are using
•
The version of HotSync Manager you are using on your PC
To find Windows operating system version information:
1. Click the Start menu in the Windows system tray on the bottom left side of
your computer screen in the Taskbar
2. Choose Settings, then click Control Panel
3. Double-Click System
To find organizer version and memory information:
1. Tap the application icon on the handheld organizer
2. Tap the menu button located on the handheld organizer
3. Tap App, and then tap info
4. Tap Version to see version numbers, and tap Size to see the amount of free
memory, in kilobytes
To find QUICKSPEC version information:
1. Tap the QUICKSPEC application icon
2. Tap the
Help/Setup button located in the top right corner
3. The version information is displayed
4. Tap the
Rev. 1.0
Exit icon to close the window
Cummins Inc.
Page 17
QUICKSPEC User's Manual
To find HotSync Manager version information:
1. Click the HotSync Manager icon in the Windows system tray on the bottom
right side of your computer screen in the Taskbar
2. Click About
Installation Problems
I’m having problems installing •
my Desktop organizer software.
Review the Palm Handbook, including its
Frequently Asked Questions. Use Palm
Technical Support if needed.
I tried to install the QuickSpec •
software on my computer and it
would not install.
Verify that your computer meets the system
requirements listed on page 5. The
QuickSpec software is not Mac-compatible.
•
HotSync Manager and the Palm Desktop
software must be installed on your computer
before QuickSpec software can be installed.
If they are not installed on your computer,
then insert the Palm Desktop CD-ROM into
your computer and wait for the Installer
Menu Screen. Click INSTALL and follow the
instructions onscreen.
I am using Desktop organizer •
software other than the Palm
Desktop software and my
QuickSpec software would not
install.
Activate the Palm Desktop software, install
the QuickSpec software, then activate the
Desktop software that you use. The latest
version of the Palm Desktop software can
be downloaded without cost at the Palm
web site: http://www.palm.com
I tried to install a new version of •
QuickSpec software and it
would not install properly on my
organizer.
Delete the old version of software from the
Palm organizer, then install the new version
of software.
Rev. 1.0
Cummins Inc.
Page 18
QUICKSPEC User's Manual
Hardware Problems
My adapter won’t turn on Try each of these in turn:
(QuickSpec shows a No Adapter
• Verify the cables are properly installed and
status).
firmly connected to the handheld device
and to the adapter.
•
Verify the Power LED on the adapter is on
steady and not blinking.
I cannot read engine/vehicle •
data (QuickSpec shows a
Datalink Down! Status).
Take the datalink cable off and install
again. Verify that the vehicle key is in the
On position and the ECM is getting power.
•
Verify the extension cables are properly
installed and firmly connected.
•
Check for loose, bent, broken, or incorrectly
installed connector pins on the cables.
•
Verify the J1708 and RS-232 LEDs on the
adapter are blinking fast.
Application Problems
I cannot save engine/vehicle •
data
QuickSpec does not save any engine data
I cannot view the data in Metric •
units
QuickSpec currently does not support
metric units
I cannot adjust any settings
•
For adjustments you must use PowerSpec
HotSync Problems
I did a HotSync operation, but •
the QuickSpec application did
not synchronize.
Verify that the HotSync Manager is running.
If the HotSync Manager is running, exit and
restart it.
•
The Palm Desktop software must be
installed and activated on your computer to
HotSync the QuickSpec software.
Rev. 1.0
Cummins Inc.
Page 19
QUICKSPEC User's Manual
Beaming Problems
I cannot beam the QuickSpec •
application to another organizer.
The QuickSpec application is
protected and cannot be beamed.
copy-
Help Desk Support Center
If you encounter a problem with your QUICKSPEC product, please contact your
local Cummins distributor only after you have reviewed the previous list of
Frequently Asked Questions, the updated Frequently Asked Questions on the
QuickCheck web site at http://quickcheck.cummins.com, and the Palm
Handbook, including its list of Frequently Asked Questions. Information about
your local Cummins distributor can be found at our web site:
http://www.cummins.com.
Note: Cummins distributors are not able to provide support for Palm
computing device platform issues. If you are having a problem with
the Palm organizer, please review the Palm Handbook, then contact
Palm Technical Support if necessary. The Handbook also includes a
list of Frequently Asked Questions that should be reviewed.
Rev. 1.0
Cummins Inc.
Page 20
QUICKSPEC User's Manual
APPENDIX D: CONNECTOR PIN-OUTS
DEUTSCH HD16 - 6 - 12S
6-position connector
-------------------------------A - J1587 +
B - J1587 C - Power +
D - NC
E - Ground
F – NC
DEUTSCH HD16 - 9 - 1939S
9-position connector
-------------------------------A - Ground
B - Power +
C - J1939 +
D - J1939 E – J1939 Shield
F - J1587 +
G - J1587 H - NC
J - NC
Rev. 1.0
Cummins Inc.
Page 21
QUICKSPEC User's Manual
6-Pin Cable P/N 3165160
DEUTSCH HD16 - 6 - 12S
DB25 Female
6-position connector
FROM PIN
TO PIN
FUNCTION
A
3
J1587 +
B
4
J1587 -
E
23
Ground
C
25
Power +
9-Pin Cable P/N 3165159
DEUTSCH HD16 - 9 - 1939S
DB25 Female
9-position connector
Rev. 1.0
FROM PIN
TO PIN
F
3
J1587 +
G
4
J1587 -
C
6
J1939 +
E
7
J1939 Shield
D
8
J1939 -
A
23
Ground
B
25
Power +
Cummins Inc.
FUNCTION
Page 22
QUICKSPEC User's Manual
GLOSSARY
Communicating
QuickSpec is in the process of re-establishing
communications on the datalink after saving data
Datalink Down!
QuickSpec is not reading any data from the
datalink
Disconnected
Parameter data is not being read from the
datalink
ECM
Electronic Control Module
Engine Info Screen
Displays Cummins engine dataplate and owner
information
Gearing Screen
Registers and displays gearing information from
a Cummins-powered vehicle
Generating Report
Indicates that QuickSpec is preparing to display
the data it has just gathered
handheld organizer
handheld device
Palm computing devices for QUICKCHECK datalink
reader:
Garmin® IQue 3600, Palm M500™, M505™,
M515™, I705™, and Tungsten™ T, T2, C, and
W
HotSync Manager®
Palm computing device synchronization
technology control software
HotSync® process
Palm computing device synchronization
technology
Identifying ECM
QuickSpec is in the process of identifying the
connected ECM
INLINE™
another Cummins Inc. datalink adapter
INSITE™
another Cummins Inc. service tool
J1587
a low-speed SAE-defined message format used
on a J1708 interface
J1939
a high-speed SAE-defined message format used
on a CAN interface
J1708
the SAE-defined hardware interface for J1587
(and J1922) messages
N/A
Data for the parameter is not available to read
Rev. 1.0
Cummins Inc.
Page 23
QUICKSPEC User's Manual
No Adapter
QuickSpec is not communicating with the adapter
QUICKCHECK™ II Adapter
Cummins Inc. datalink reader compatible with the
QuickCheck II application, but not compatible
with the QuickSpec application
QUICKCHECK™ III Adapter
Cummins Inc. datalink reader compatible with the
QuickSpec application
Reading Dataplate
Indicates that data is being read by QuickSpec
Reading Features
Reading Passwords
Reading Trims
Reading Trip Data
SAE
Settings Screen
Rev. 1.0
Society
of
Automotive
Engineers,
the
organization that establishes on-road and offroad motor vehicle standards
Displays settings and trims from a Cummins
engine
Cummins Inc.
Page 24
QUICKSPEC User's Manual
INDEX
software · 6
A
Activating QuickSpec · 10
Application · 10
Archiving data · 13
C
J
J1939 · 4
P
Palm Computing
handheld organizers · 4
Cables
kit contents · 16
optional cables · 16
pin-outs · 21
Q
QUICKSPEC
definition · 4
version · 17
D
Datalink adapter · 9
E
R
Requirements
handheld device · 4
HotSync software · 4
PC · 5
Expansion Switches · 12
H
Help
about box · 10
basic navigation · 10
frequently asked questions · 17
support center · 20
tutorial · 14
HotSync
software · 4
S
SAE J1587 · 4
Screen
Gearing · 12
Engine Info · 11
Settings · 11
Scrollbar · 12
I
T
Installation
Tap and Hold Tool-tip · 12
Tutorial · 14
adapter · 9
Rev. 1.0
Cummins Inc.
Page 25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement