FACT_Manual_Keyboard_Menu_Flow_3_3

FACT_Manual_Keyboard_Menu_Flow_3_3
Futura Advanced Continuity Tester (FACT)
User’s manual version 3.3,
Firmware version FACT_512 M: D.4, Slave 2.3
FACT Editor Version 5.2
By
Futura Apsol Pvt. Ltd.
1212/B, "Seeta Apts.", Apte Road, Shivajinagar,
Pune - 411 004
India
Tel: 020 -25531832 / 9881138785
[email protected]
www.futuras.com
1: IMPORTANT NOTES:
1.1: Packing: Preserve the packing sent along with the tester which is specially designed for protection of the tester during transportation. In case tester is to be sent back to Futura, use the same
packing.
1.2: Safety notes:
Safety Notes! Please read before putting the system into operation!
This system has been checked for safe and correct functioning before being shipped. In order to keep
this safety, the user has to pay attention to the corresponding notes and advice of the operating
manual.
#
Before connecting test samples to the instrument, check for strictly separation of the sample from
power!
Any connection of the test sample to power can be dangerous for the operator and can damage
electronics.
#
Before connecting test samples to the instrument, check for static charges of the test sample, fixtures
and operator which are to be eliminated. Otherwise the test electronics can be damaged.
#
Any external continuity meter like buzzer, bulb or multimeter should be strictly avoided. Use of these
will damage the test electronic.
#
While changing the board; removal and fitting of D type connectors on the back side of the tester or
Centronics connector on the board should be done with utmost care. These connectors are polarised
and hence should not be inserted in wrong direction. There is a tendency to push the connector hard
in the tester even if polarization is incorrect. Pushing might damage the connectors on I/O cards or
on the board of the tester.
# Check proper earthing at the power supply input of the Cable Harness Tester.
Warranty void if equipment is opened by unauthorized person.
FACT : Is an easy to use tester with self explanatory menus displayed.
Following are details of keys and menus.
Power on the ‘FACT’:
FACT is provided with Power supply and main’s cord. Three pin connector
receptacle is must for powering. Input range of power supply is variable from
100 to 240VAC (50/60 HZ).
At power on the “FACT”, following activities being done.
A) Self test is carried out
B) Initial display i.e. firmware version, tester serial number etc. is displayed
as below.
FUTURA
FACT
SR. No.
TEST POINTS
VER xxx
xxxxxxxx
xxxx
C) Above display is preceded by next one which is control gateway for functional operations.
MENU: MAIN
>TEST
BRD_CHK
SETUP
PN xxx
SELECT
ANALYSE
COUNT
“ >” symbol can be used as cursor to select menu items.
For menu navigation, four keys have been provided.
• Diagonal, Up and Down arrow buttons are used to move the cursor.
• Grey square button is to enter or select particular menu or function.
• Red square button is used to escape from existing menu or to go back.
FACT Keyboard & Menu Flow:
Main Menu:
This is the main menu displayed at Power on when program stops execution
and display becomes idle.
• First line displays default current menu appeared and last program selected. If no program is selected then program number 01 is appeared
by default.
• Rest all three lines displays various sub menus under upper menu.
(* this scheme is repeated for various menus and sub menus thought
the program flow)
MENU: MAIN PN xxx
>TEST
SELECT
BRD_CHK
ANALYSE
SETUP
COUNT
Shows current menu & last selected Prg
Sub menus
Sub menus
Sub menus
MAIN > TEST : (AUTHO: OPERATOR +)
MENU: MAIN PN xxx
>TEST
SELECT
BRD_CHK
ANALYSE
SETUP
COUNT
PROGRAM NUMBER xx
OPEN
xxxxxxxxx
OR
NAME
.…..
OR
……
PUT CABLE
MAIN > SELECT: (AUTHO: OPERATOR +)
• Select menu is provided to select a program.
• Total program location capacity user configurable, depending on label data size
and no. of I/O cards.
• Selected program remains selected through execution and after power off also;
unless override by new one.
• After selecting the program, all the settings and data with respect to program location are retrieved.
MENU: MAIN
PN xxx
TEST
> SELECT
BRD_CHK
ANALYSE
SETUP
COUNT
PROGRAM NO (PN) -> xxx
STAGES. xx
PTS xxxx
PRESS ENT TO SELECT
Display Meanings:
1st line: Currently Selected Program number or name.
2nd line: No. of stages present at location.
3rd line: Total number of points present.
4th line: Action for selection.
Key Board Action:
: Enter scroll single digit
ENT: Select the digit and proceed
ESC: Return to main menu
MAIN > BRD_CHK: (AUTHO: OPERATOR +)
•
•
•
FACT now is in board check mode.
User should connect the probe at BRD CHK terminal and physically connect
other terminal at fixture points.
Point at which probe is connected is displayed.
MENU: MAIN
TEST
>BRD_CHK
SETUP
PN xxx
SELECT
ANALYSE
COUNT
Display Meanings:
1st line: Indicative information.
2nd line: Indicative information.
3rd line: Indicative information.
4th line: Displays point read during board check.
! BOARD DIAGNOSTICS!
! CONNECT PROBE!
POINT--------- > 0000
Key Board Action:
: No action
ENTER: No action
ESC : Return to main menu
MAIN: ANALYSE: (AUTHO: SUPERVISOR +)
•
•
This menu is provided for analyzing settings, data, and current configuration
Various sub menus can be accessed
MENU: MAIN
TEST
BRD_CHK
>
SETUP
PN xxx
SELECT
ANALYSE
COUNT
MENU: ANALYSE PN xxx
>DSP_HRN
GEN-SETT
CBL-SETT
CMP FLG
COUNT
BRDCHK
Display Meanings:
1st line: Shows current menu & last selected Program
2nd line: Sub menus.
3rd line: Sub menus.
4th line: Sub menus.
Key Board Action:
: Navigate through A menu
ENTER: Selected the menu
ESC : Back to main menu
MAIN > SETUP: (AUTHO: SUPERVISOR +)
•
•
•
•
This is the most important menu in FACT.
To access set-up menu soft key i.e. configured key (USB) is necessary.
Setup menu has various authority levels.
Editing in stored data, Storing and overriding new data ,changes in settings,
Authority assignments, and all other controlled activities can be done through
Set up menu.
MENU: MAIN
TEST
BRD_CHK
> SETUP
PN xxx
SELECT
ANALYSE
COUNT
MENU: SETUP
PN xxx
FCT-DATA
OTH-DATA
GEN-SETT
PRG-SETT
DIAGNO
FCTRY-SET
Display Meanings:
1st line: Shows current menu
2nd line: Sub menus.
3rd line: Sub menus.
4th line: Sub menus.
Key Board Action:
: Navigate through Set up menu
ENTER: Selected the menu
ESC : Back to main menu
MAIN: COUNT (AUTHO: OPERATOR +)
•
•
•
This function tells current status of pass and fails counts.
Selected program location is shown
User can analyze count status.
MENU: MAIN PN xxx
TEST
SELECT
BRD_CHK
ANALYSE
SETUP
>COUNT
Display Meanings:
1st line : Currently selected program.
2nd line: Indicative information
3rd line: Indicative information.
4th line: Blank.
Key Board Action:
: No Action
ENTER: No Actions
ESC : Back to main menu
PROGRAM NO (PN) xxx
PASS xxx
FAIL xxx
MAIN > ANALYSE > DISP HRN: (AUTHO: SUPERVISOR +)
•
•
•
•
•
Sub menu of Analyze.
This menu displaces harness data which is stored into the memory.
After display tester comes back to Analyze menu.
Harness data for selected program location is displayed.
If any diodes configured then diode data is displayed.
MENU: ANALYSE PN xxx
>DISP-HRN
GEN-SETT
PRG-SETT
CMP FLG
COUNT
BRDCHK
PROGRAM NO (PN) -> xxx
POINTS
….
Display Meanings:
1st line: Currently selected program.
2nd line: Points.
3rd line: Actual points.
4th line: Actual points.
Key Board Action:
: No action
ENTER: No action
ESC : Back to Analyze menu
MAIN>ANALYSE> GEN-SETT: (AUTHO: (MANAGER + ) IS COMPULSORY)
•
Status of the various general settings can be viewed through this menu.
MENU:ANALYSE PN xxx
DISP-HRN
>GEN-SETT
CBL-SETT
CMP FLG
COUNT
BRDCHK
MENU: GEN-SETT PN xxx
>AUTO MODE
- ON
LEARN
- OFF
GLB BAR
- OFF
Display Meanings:
1st line: Shows current menu & last selected Program.
2nd line: General Setting.
3rd line: General Settings.
4th line: General Settings.
Key Board Action:
: Navigate through setting.
ENTER: No action.
ESC : Back to Analyze menu.
ANALYSE > PRG-SETT: (AUTHO: SUPERVISOR +)
•
Status of the various program specific settings can be viewed through this
menu.
MENU:ANALYSE PN xxx
DISP-HRN
GEN-SETT
>PRG-SETT
CMP FLG
COUNT
BRDCHK
MENU: CBL-SETT PN xxx
>2STG
--- ON
--------------- OFF
--------------- OFF
Display Meanings:
1st line: Currently selected program.
2nd line: Program Settings
3rd line: Program Settings.
4th line: Program Settings.
Key Board Action:
: Navigate through settings.
ENTER: No action.
ESC : Back to Analyse menu.
MAIN > ANALYSE > CMP FLG: (AUTHO: SUPERVISOR +)
•
This feature is not available in this version so control returns back to ANALYSE
MENU.
MENU: ANALYSE PN xxx
DISP-HRN
GEN-SETT
PRG-SETT
>CMP FLG
COUNT
BRDCHK
“NOT AVAILABLE”
MAIN > ANALYSE >COUNT: (AUTHO: SUPERVISOR +)
•
This menu provides Pass and Fail count status for selected program number.
Display
Meanings:
MENU:ANALYSE
PN xxx
DISP-HRN
GEN-SETT
PRG-SETT
CMP FLG
>COUNT
BRDCHK
PROGRAM NO (PN) xxx
PASS xxx
FAIL xxx
1st line: Shows current menu & last selected Program.
2nd line: Pass count.
3rd line: Fail Count.
4th line: Blank.
Key Board Action:
: Navigate through setting
ENTER: No action
ESC : Back to Analyze menu
MAIN >ANALYSE > BRDCHK: (AUTHO: SUPERVISOR +)
•
•
•
FACT now is in board check mode
User should connect the probe at BRD CHK terminal and physically connect at
fixture point
Point at which probe is connected is displayed.
MENU:MAIN
TEST
>BRDCHK
SETUP
PN xxx
SELECT
ANALYSE
COUNT
Display Meanings:
1st line: Indicative information
2nd line: Indicative information
3rd line: Indicative information
4th line: Displays point read during board check.
Key Board Action:
: No action
ENTER: No action
! BOARD DIAGNOSTICS !
! CONNECT PROBE !
POINT ……. 0000
ESC
: Return to main menu
MAIN > SET UP > FCT-DATA > DATA: (AUTHO: SUPERVISOR +)
•
•
•
•
•
This menu will learn the harness present on the board.
This option will only available for HRN DATA.
For any other menu it is unavailable.
If the harness is not mounted then old data will be retained.
This option is not available for LBL data menu.
MENU: FCT-DATA PN xxx
>LRN DATA
PC-DATA?
DATA-PC?
USB-DATA?
DATA-USB?
DEMO-LBL?
PROGRAM NO (PN) xxx
.
LEARNING
PTS ….
SAVING MEMORY
MEMORY CHK-PASS
Display Meanings:
1st line: Selected Program
2nd line: Indicative information.
3rd line: Indicative information.
4th line: Indicative information.
Key Board Action:
: Navigate through menu
ENTER : Select a function
ESC : Return to setup menu
MAIN > SET UP > FCT-DATA > PC- DATA: (AUTHO: SUPERVISOR +)
•
•
•
•
Tester is in wail state for data from PC
Use only Futura’s FACT editor software for interfacing with tester.
Data can be transferred through PC via serial port.
After valid data reception control will reach towards parent menu.
MENU: FCT DATA PN xxx
LRN DATA
>PC-DATA?
DATA-PC?
USB-DATA?
DATA-USB?
DEMO-LBL?
Display Meanings:
RECEIVING MODE
SEND DATA
1st line: Blank.
2nd line: Indicative information.
3rd line: Indicative information.
4th line: Blank.
Key Board Action:
: No action
ENTER : No action
ESC : Back to parent menu
MAIN > SET UP > FCT-DATA > DATA-PC: (AUTHO: SUPERVISOR +)
•
•
•
Data is sent on serial port to PC which can be gathered by FACT editor.
FACT editor only can be interfaced for serial reception.
After execution control reaches to parent menu.
MENU: FCT DATA PN xxx
LRN DATA
PC-DATA?
>DATA-PC?
USB-DATA?
Display
Meanings:
DATA-USB?
DEMO-LBL?
PROGRAM NO (PN) xxx
SENDING
MEMORY CHK-----PASS
1st line: Shows current selected program
2nd line: Indicative information.
3rd line: Blank.
4th line: Indicative information.
Key Board Action:
: No action
ENTER : No action
ESC : No action
MAIN > SET UP > FCT-DATA > USB-DATA: (AUTHO: SUPERVISOR +)
•
•
Before entering into menu, USB pen drive requires .f01 files.
After selection, file will be saved to corresponding location and control returns
back.
MENU: FCT DATA PN xxx
LRN DATA
PC-DATA?
DATA-PC?
>USB-DATA?
DATA-USB?
DEMO-LBL?
PROGRAM NO (PN) xxx
>xxx.F01
xxx.F01
xxx.F01
Display Meanings:
1st line: Shows current selected program
2nd line: File Name.
3rd line: File Name.
4th line: File Name.
Key Board Action:
: Navigate through files
ENTER : Select & save a file
ESC
: Return to parent menu
MAIN > SET UP > FCT-DATA > DATA-USB: (AUTHO: SUPERVISOR +)
•
•
•
File stored in the current program location will be saved in the pen drive.
File name and extension will define what kind of file it is.
Example: 12FCT.F01
12 Current selected location.
.FO1 Usb file format for harness data.
MENU: FCT DATA
PN xxx
LRN DATA?
PC-DATA?
DATA-PC?
USB-DATA?
>DATA-USB?
DEMO-LBL?
SENDING
Display Meanings:
1st line: Blank.
2nd line: Indicative information
3rd line: Blank.
4th line: Blank.
Key Board Action:
: Navigation
ENTER : Send selected file to USB & control returns to parent menu.
ESC : Back to HRN data menu
MAIN > SET UP > FCT-DATA > DEMO - LBL: (AUTHO: SUPERVISOR +)
•
•
User can take demo label print for reference.
Serial number in demo print always remains steady.
MENU: FCT DATA
PN xxx
LRN DATA?
PC-DATA?
DATA-PC?
USB-DATA?
>DATA-USB?
DEMO-LBL?
PRINTING……
Display Meanings:
1st line: Blank.
2nd line: Indicative information.
3rd line: Blank.
4th line: Blank.
Key Board Action:
: Navigate through setting
ENTER : Allowed action is performed.
ESC
: Back to set up menu.
MAIN> SET-UP > OTH-DATA: (AUTHO: SUPERVISOR +)
•
•
•
•
Various other settings can be changed through this menu.
Date and time can be configured through RTC menu.
Operator codes can be set through OPCODE menu.
Two operator codes are allowed to scan.
MENU: OTH-DAT
PN xxx
>RTC
-----------OPCODE1
OPCODE2
-------------------------
DATE_TIME 24 HRS
00/00/0000
00:00:00
Display Meanings:
1st line: Shows current menu & last selected Program.
2nd line: Program Setting.
Allowed action?
3rd line: Program Settings.
Allowed action?
4th line: Program Settings.
Allowed action?
Key Board Action:
: Navigate through setting
ENTER: Select the menu
ESC : Back to set up menu.
MENU: OTH-DAT
PN xxx
RTC
----------->OPCODE1
OPCODE2
-------------------------
Display Meanings:
1st line: Blank
2nd line: Indicative information.
3rd line: Blank
4th line: Blank
Key Board Action:
: Navigate through setting
ENTER: Select the menu
ESC : Back to set up menu.
RECEVING MODE
MAIN > SET-UP > GEN-SETT: (AUTHO: (MANAGER + ) IS COMPULSORY)
•
Various general settings can be changed through this menu.
MENU: SETUP
FCT-DATA
OTH-DATA
>GEN-SETT
PRG-SETT
DIAGNO
FCTRY-SET
MENU: GEN-SETT
AUTO MODE
LEARN
GLB BAR
PN xxx
ON ?
OFF ?
ON ?
Display Meanings:
1st line: Shows current menu & last selected Program.
2nd line: General Setting.
Allowed action?
3rd line: General Settings.
Allowed action?
4th line: General Settings.
Allowed action?
Key Board Action:
: Navigate through setting
ENTER : Allowed action is configured.
ESC
: Back to set up menu.
MAIN > SET-UP > PRG-SETT: (AUTHO: SUPERVISOR +)
•
Various general settings can be changed through this menu.
MENU: SETUP
FCT-DATA
OTH-DATA
GEN-SETT
>PRG-SETT
DIAGNO
FCTRY-SET
MENU: PRG-SETT PN xxx
>2 STG
ON ?
-------------OFF ?
-------------ON ?
Display Meanings:
1st line: Shows current menu & last selected Program.
2nd line: Program Setting.
Allowed action?
rd
3 line: Program Settings.
Allowed action?
4th line: Program Settings.
Allowed action?
Key Board Action:
: Navigate through setting
ENTER: Select the menu
ESC : Back to set up menu.
MAIN >SET-UP> DIAGNO: (AUTHO: SUPERVISOR +)
•
•
Diagnostic menu is used to diagnose various peripherals of tester.
IO cards, serial port, Parallel port, Buzzer, Digital I/O box can be diagnosed.
MENU: SETUP
FCT-DATA
OTH-DATA
GEN-SETT
CBL-SETT
>DIAGNO
FCTRY-SET
MENU: DIAGNO
>I/O TEST
PARALLEL
DIG I/O
PN xxx
RS232
BUZZER
E2PROM
Display Meanings:
1st line: Shows current menu & last selected Program.
2nd line: Sub Menu.
3rd line: Sub Menu.
4th line: Sub Menu.
Key Board Action:
: Navigate through setting
ENTER : Select the menu
ESC
: Back to set up menu.
MAIN >SET-UP> FCTRY-SET: (AUTHO: SUPERVISOR +)
•
•
•
Tester is set to factory settings i.e. default settings.
All general settings, counters, volume, tone, relay on time etc are set to default.
Tester restarts after factory settings.
MENU: SETUP
FCT-DATA
OTH-DATA
GEN-SETT
CBL-SETT
DIAGNO
>FCTRY-SET
Display Meanings:
1st line: Indicative information.
2nd line: Indicative information.
3rd line: Blank
4th line: Blank
SET TESTER TO
FACTORY SETTINGS?
Key Board Action:
: No action
ENTER : Allowed action is executed.
ESC
: Back to set up menu.
MAIN > SET UP > FUT-DND: :(AUTHO: FUTURA DND)
•
This menu is restricted to Futura only.
MAIN > SET UP> VOLUME: (AUTHO: SUPERVISOR +)
MENU: SETUP
PN xxx
GEN-SETT
CBL-SETT
DIAGNO
AUTHORITY
FUT-DND
>VOLUME
VOLUME LEVEL
------> 08?
Display Meanings:
1st line: Shows current menu & last selected Program.
2nd line: Sub Menu.
3rd line: Sub Menu.
4th line: Blank.
Key Board Action:
: Volume increase
: Volume decrease
ENTER : Select volume & back to set up menu
ESC
: Back to setup menu
MAIN > SET UP > CHNG TONE: (AUTHO: SUPERVISOR +)
•
Any tone combination can be set.
MENU: SETUP
PN xxx
DIAGNO
AUTHORITY
FUT-DND
VOLUME
>CHNG TONE
RELAYTIME
TONE TYPE 1?
PASS TONES
Display Meanings:
1st line: Tone Type
2nd line: Pass or fail tone.
3rd line:
4th line:
Key Board Action:
: Navigate through tone menu
ENTER : Select tone & back to set up menu
ESC
: Back to setup menu
MAIN >SET UP > RELAY TIME: (AUTHO: SUPERVISOR +)
•
•
FACT tester is given with 2 relay drivers
Relay on time can be configured through this menu
MENU: SETUP
PN xxx
DIAGNO
AUTHORITY
FUT-DND
VOLUME
CHNG TONE > RELAYTIME
RELAY ON TIME
-----> 2?
Display Meanings:
1st line: Indicative information
2nd line: On time display.
3rd line:
4th line:
Key Board Action:
: Navigation through relay on time
ENTER : Select the real time & go back to set up menu
ESC : Return to setup menu
MAIN> SET UP> CLR CNTS: (AUTHO: SUPERVISOR +)
•
•
Various counters can be cleared through this menu
Relay on time can be configured through this menu
MENU: SETUP
PN xxx
FUT-DND
VOLUME
CHNG TONE
RELAYTIME
>CLR CNTS
CONFIGURE
PROGRAM NO (PN) xxx
PASS CNT
CLEAR?
FAIL CNT
CLEAR?
SR. NO.
CLEAR?
Display Meanings:
1st line: Selected program
2nd line: Count
Allowed action
3rd line: Count
Allowed action
4th line: Count
Allowed action
Key Board Action:
: Navigation through menu
ENTER: Clear desired count & go back to set up menu
ESC : Return to setup menu
MAIN >SET UP > CONFIGURE: (AUTHO: (MANAGER +) IS COMPULSORY)
Tester can be set at four different memory schemes.
Combinations:
1k label --- max test points 512, 128 locations available.
2k label --- max test points 512, 096 locations available.
4k label --- max test points 512, 064 locations available.
8k label --- max test points 512, 032 locations available.
• Tester restarts after configuration.
•
•
MENU: SETUP
PN xxx
FUT-DND
VOLUME
CHNG TONE
RELAYTIME
CLR CNTS
>CONFIGURE
Display Meanings:
1st line: Indicative information
2nd line: Indicative information
3rd line: Blank
4th line: Blank
Key Board Action:
: Navigation through various combinations.
ENTER : Select combination.
ESC
: Return to setup menu
LABEL DATA SIZE
-----> 1K ?
MAIN >SET UP > DIAGNO > IO TEST: (AUTHO: SUPERVISOR +)
•
•
Self test of all IO cards is carried out.
On pass or fail respective buzzer sounds.
MENU: DIAGNO
>I/O TEST
PARALLEL
DIG I/O
PN xxx
RS232
BUZZER
E2PROM
SELF IO TEST
PASS OR FAIL
Display Meanings:
1st line: Indicative Information
2nd line: Indicative Information
3rd line: Blank
4th line: Blank.
Key Board Action:
: Navigate through setting
ENTER: Select the menu
ESC
: Back to diagno up menu.
MAIN >SET UP > DIAGNO > RS 232: (AUTHO: SUPERVISOR +)
•
•
Rs232 functionality test is carried out.
After connecting of RS232 dongle test is carried and result is shown.
MENU: DIAGNO
PN xxx
I/O TEST
> RS232
PARALLEL
BUZZER
DIG I/O
E2PROM
Display Meanings:
1st line: Blank.
2nd line: Indicative Information
3rd line: Indicative Information
4th line: Blank.
Key Board Action:
: NO Action
CONNECT DONGLE AND
PRESS ENT
ENTER: Serial test and return to diagno menu.
ESC
: Back to diagno menu.
MAIN >SET UP > DIAGNO > PARALLEL: (AUTHO: SUPERVISOR +)
•
•
Dot matrix printer with parallel port is required for this test.
Tester prints “test print” ensures proper working of parallel port.
MENU: DIAGNO
PN xxx
I/O TEST
RS232
>PARALLEL
BUZZER
DIG I/O
E2PROM
CONNECT DOT MATRX
PRINTER AND
PRESS ENT
Display Meanings:
1st line: Indicative Information
2nd line: Indicative Information
3rd line: Indicative Information
4th line: Blank.
Key Board Action:
: NO Action
ENTER : Performs parallel test.
ESC
: Back to diagno menu.
MAIN >SET UP > DIAGNO > BUZZER: (AUTHO: SUPERVISOR +)
•
•
Buzzer sounds continuously in incrementing decrementing cyclic manner.
Buzzer is tested.
MENU: DIAGNO
PN xxx
I/O TEST
RS232
PARALLEL
> BUZZER
DIG I/O
E2PROM
BUZZER TONE
Display Meanings:
1st line: Blank
2nd line: Indicative Information
3rd line: Blank
4th line: Blank
Key Board Action:
: NO Action
ENTER : Performs buzzer test.
ESC
: Back to diagno menu.
Factory settings:
1. General settings
AUTO MOD
LEARN
GLB BAR
GLB PRN
EXTRA PT
ALL CKT
RLYPASS1
RLYPASS2
TWO BAR
TMOUT PRN
AUTHORITY
CMPR ONLY
HACG
SUP_VISOR
OPERATOR
HRN FAIL
POKA-YOKE
FAIL-BIN
FIRST FAIL
CLR-BIN
ON.
ON.
OFF.
ON.
OFF.
OFF.
ON.
ON.
OFF.
OFF.
OFF.
OFF.
OFF.
OFF.
OFF.
OFF.
OFF
OFF
OFF.
OFF
2. Volume is set at level 5.
3. Relay on time is set at 1 second for both relay outputs.
4. All counters such as pass, fail, serial number etc are cleared.
FACT Message Code and their meanings:
•
Message 82: MSD (mass storage device) or pen drive in not connected or MSD
is not detected.
•
Message 83: MSD is not burned with appropriate authority.
•
Message 84: MSD is not burned with login data base.
•
Message 85: File in the USB format .f01 is not found in MSD.
•
Message 86: Error occurred during file opening in MSD.
•
Message 87: MSD is not properly burned with authority.
•
Message 88: MSD is not properly burned with login data base.
•
Message 89: FCT file is corrupted in MSD.
•
Message 8A: Data format in file in MSD is incorrect.
•
•
Message 8B: FACT internal communication error (revert back to Futura support).
Message 8C: File cannot be created in MSD USB error.
•
Message 8D: Invalid tone number selected.
•
Message 8E: Manager Authority is not present.
Version Change record
FACT_512 M: D.1 S: 2.3:•
Diode testing facility is added.
•
Factory settings are added.
•
Tester is available with new memory scheme.
FACT_512 M: D.1 S: 2.3 modification note:
•
Diode testing feature is added in this version.
•
FACT editor with ver 5.2 and higher are only applicable for this version.
•
User must use FACT editor ver 5.2 or higher for proper operation.
•
Up to 50 diodes can be tested in each harness.
•
Faults such as
•
Diode open: Diode missing or open from inside.
•
Diode short: Diode short from inside or wire assembled instead of diode.
•
Can be found out.
•
Diode data has to be configured from .fct file in diode tag given. (Refer
demo.fct file given along with.)
•
Two harness points in which diode exists, must be present in harness data in
stage tag in .fct file.
•
Refer demo.fct file for data configuration.
FACT_512 M: D.4 S: 2.3 modification note:
•
Special poka-yoke testing mode is added for full proof operation.
•
Fail bin sensor input is added.
•
Stop at first fault settings added poka-yoke mode.
Packing list:
FACT Tester--------------------------------- 1 NO.
Power supply--------------------------------- 1 NO.
Mains cod------------------------------------ 1 NO.
Relay and digital input unit---------------- 1 NO.
Relay and digital input interfacing cable (15 P M- 15 P M)-1 NO.
Standard modem cable (9 P M – 9 P F)-1 NO.
Futura 121 cable (9 P M- 9 P M) ----1 NO.
Futura Cross cable (9 P M-9 P M) ---1 NO.
FACT FRC cable (64 P FRC F- 64 P FRC F) ------- 1 NO for every IO card.
FUTURA INTERFACE PBT 0410 PCB--------------1 NO for every IO card.
Board check probe--------------------------------------- 1 NO.
Serial Dongle---------------------------------------------1 NO
Futura CD ------------------------------------------------ 1 NO.
This users manual-----------------------------------------1 NO.
Serial number---------------------------
Futura Advanced Continuity Tester (FACT)
User’s manual version 3.2,
Firmware version FACT_512 M:D.4, Slave 2.3
FACT Editor Version 5.2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement