GOT2000 Series

Video/RGB Input Unit

User's Manual

GT27-V4-Z

Set of GT16M-V4-Z and GT27-IF1000

GT27-V4R1-Z

Set of GT16M-V4R1-Z and GT27-IF1000

GT27-R2-Z

Set of GT16M-R2-Z and GT27-IF1000

Thank you for purchasing the GOT2000 Series.

Prior to use, please read both this manual and detailed manual thoroughly to fully understand the product.

MODEL

MODEL

CODE

GT27-V4R1-Z-U-JE

1D7ML4

IB(NA)-0800519-B(1407)MEE

 SAFETY PRECAUTIONS

(Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly.

The precautions given in this manual are concerned with this product.

In this manual, the safety precautions are ranked as "WARNING" and "CAUTION".

WARNING

Indicates that incorrect handling may cause hazardous conditions, resulting in death or severe injury.

CAUTION

Indicates that incorrect handling may cause hazardous conditions, resulting in medium or slight personal injury or physical damage.

Note that the circumstances.

CAUTION level may lead to a serious accident according to the

Always follow the precautions of both levels because they are important to personal safety.

Please save this manual to make it accessible when required and always forward it to the end user.

[DESIGN PRECAUTIONS]

CAUTION

 Do not bunch the control wires or communication cables with the main circuit or power wires, or lay them close to each other.

As a guide, separate the lines by a distance of at least 100mm (3.94 inches) otherwise malfunctions may occur due to noise.

[INSTALLATION PRECAUTIONS]

WARNING

 Be sure to shut off all phases of the external power supply used by the system before mounting or removing this unit to/from the GOT. Not doing so can cause a unit failure or malfunction.

 Before connecting the Bus connection cable to this unit, always shut off GOT power and PLC CPU power externally in all phases.Not doing so can cause a malfunction.

CAUTION

 Use this unit in the environment that satisfies the general specifications described in the User's Manual for the GOT used. Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration.

 Do not drop the unit or subject it to string shock.

A unit damage may result.

 When installing this unit to the GOT, fit it to the connection interface of the

GOT and tighten the mounting screws in the specified torque range (0.36

N•m to 0.48 N•m) with a Phillips-head screwdriver No.2.

Undertightening can cause a drop, failure or malfunction. Overtightening can cause a drop, failure or malfunction due to screw or unit damage.

[WIRING PRECAUTIONS]

WARNING

 Be sure to shut off all phases of the external power supply used by the system before wiring.

Failure to do so may result in an electric shock, product damage or malfunctions.

CAUTION

 Exercise care to avoid foreign matter such as chips and wire offcuts entering the unit.

Not doing so can cause a fire, failure or malfunction.

 Make sure to securely connect the cable to the connector of unit.

Incorrect connection may cause malfunctions.

[STARTUP AND MAINTENANCE PRECAUTIONS]

WARNING

 Before starting cleaning, always shut off GOT power externally in all phases.

Not doing so can cause a unit failure or malfunction. Undertightening can cause the GOT to drop, short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit.

 Do not disassemble or modify any unit.

This will cause failure, malfunction, injuries, or fire.

 Do not touch the conductive areas and electronic parts of this unit directly.

Doing so can cause a unit malfunction or failure.

CAUTION

 Always secure the cables connected to the unit, e.g. run them in conduits or clamp them. Not doing so can cause unit or cable damage due to dangling, moved or accidentally pulled cables or can cause a malfunction due to a cable contact fault.

 Do not hold the cable part when unplugging any cable connected to the unit.

Doing so can cause unit or cable damage or a malfunction due to a cable contact fault.

 Always make sure to touch the grounded metal to discharge the electricity charged in the body, etc., before touching the unit. Failure to do so may cause a failure or malfunctions of the unit.

[DISPOSAL PRECAUTIONS]

CAUTION

 Dispose of this product as industrial waste.

[TRANSPORTATION PRECAUTIONS]

CAUTION

 Make sure to transport the GOT main unit and/or relevant unit(s) in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of the User's Manual for the GOT used, as they are precision devices.

Failure to do so may cause the unit to fail.

Check if the unit operates correctly after transportation.

[TRANSPORTATION PRECAUTIONS]

CAUTION

 When fumigants that contain halogen materials such as fluorine, chlorine, bromine, and iodine are used for disinfecting and protecting wooden packaging from insects, they cause malfunction when entering our products.

Please take necessary precautions to ensure that remaining materials from fumigant do not enter our products, or treat packaging with methods other than fumigation (heat method).

Additionally, disinfect and protect wood from insects before packing products.

Manuals

The following shows manuals relevant to this product.

Detailed Manual

Manual name

GOT2000 Series User's Manual (Hardware)

(Sold separately)

Manual number

(Model code)

SH-081194ENG

(1D7MJ5)

GOT2000 Series Connection Manual

(Microcomputers, MODBUS Products,

Peripherals) For GT Works3 Version1

SH-081200ENG

(1D7MK2)

For detailed manuals, refer to the PDF manuals stored in the DVD-ROM for the drawing software used.

Relevant Manuals

For relevant manuals, refer to the Help or the :PDF manuals stored in the DVD-

ROM for the drawing software used.

The latest manuals are also available from MITSUBISHI ELECTRIC FA Global

Website (http://www.MitsubishiElectric.co.jp/fa/).

© 2013 MITSUBISHI ELECTRIC CORPORATION

Compliance with the EMC and Low Voltage

Directives

To configure a system meeting the requirements of the EMC and Low Voltage

Directives when incorporating the Mitsubishi GOT (EMC and Low Voltage

Directives compliant) into other machinery or equipment, refer to "EMC AND LOW

VOLTAGE DIRECTIVES" of the General Description included with the GOT used.

The CE mark, indicating compliance with the EMC and Low Voltage Directives, is printed on the rating plate of the GOT.

Packing List

After unpacking the box, check that the following products are included.

Model Product Quantity

GT16 Video input unit GT16M-V4-Z 1

GT27-V4-Z Video Interface Converter Unit GT27-IF1000

Mounting screw set (2 screws (26mm), 2 stickers)

1

4

GT27-V4R1-Z

GT27-R2-Z

GT16 Video/RGB input unit GT16M-V4R1-Z

Video Interface Converter Unit GT27-IF1000

Mounting screw set (2 screws (26mm), 2 stickers)

GT16 RGB input unit GT16M-R2-Z

Video Interface Converter Unit GT27-IF1000

Mounting screw set (2 screws (26mm), 2 stickers)

4

1

1

1

1

4

1. OVERVIEW

This User's Manual describes the following units.

When mounting the following units with the GT27, the GOT can display video images taken by a camcorder or a RGB screen.

• The GT 27 video input unit GT27-V4-Z (hereinafter referred to as the video input unit) is configured with the GT 16 video unit and the Video Interface Converter

Unit.

For the video input unit, the GOT can display video images taken by up to four camcorders.

• The GT 27 video/RGB input unit GT27-V4-Z (hereinafter referred to as the video/RGB input unit) is configured with the GT16 video/RGB input unit and the

Video Interface Converter Unit.

For the video/RGB input unit, the GOT can display video images taken by up to four camcorders or a RGB screen for up to one device for the RGB input.

• The GT27 RGB input unit GT27-R2-Z (hereinafter referred to as the RGB input unit) is configured with the GT16 RGB input unit and the Video Interface

Converter Unit.

For the RGB input unit, the GOT can display only one RGB screen by switching up to two video input channels.

For the video input with using the above units, the GOT can be used as a vision sensor monitor.

For the RGB input unit with using the above units, the units can be used as the

RGB output type vision sensor.

GOT *1

A 1254

B 348

GT27-V4R1-Z

注意 CAUTION

誤動作の 恐れあり

通電中 着脱しないでください

Do not mount not desmount supplied.

Video camera

*1*2

Personal computer *3*4 PLCs for line control

* 1:Power on the GOT simultaneously with the camcorder.

*2:Depending on the camcorder type, noise from the power supply cable of the camcorder may cause malfunction of the GOT or a programmable controller.

In this case, attach the following line filter to the power supply line of the camcorder.

Recommended line filter: TDK-Lambda RSHN-2003 (or equivalent products)

*3:If the flickering of the screen occurs due to the noise from the RGB cable, attach the following ferrite core to the RGB input section.

Recommended ferrite core: TDK-Lambda ZCAT3035-1330 (or equivalent products)

*4:When connecting any of the above units to a personal computer, ground the ground cable of the personal computer.

To use the video input unit, video/RGB input unit, and RGB input unit, set the controller settings.

For the settings and system configurations, refer to GOT2000 Series Connection

Manual (Microcomputer, MODBUS Products, Peripherals) for GT Works3 Version

1.

For the details of the video input, video/RGB input, and RGB input function, refer to

GT Designer3 (GOT2000) Help.

2. SPECIFICATIONS

The performance specifications of the video input unit, video/RGB input unit, and RGB input unit are indicated below.

The general specifications of the video input unit, video/RGB input unit, and RGB input unit are the same as those of the GOT.

Refer to the User's Manual for the GOT used for the general specifications of the

GOT.

Video input section *2

RGB input section

Item

GT16M-V4

NTSC format, PAL format(interlaced format)

EIA format, CCIR format

(interlaced format)

Specifications

GT16M-V4R1

Video input format

Color

Number of video input channels

Input signal

Monochro me

4 channel

Display size

IVp-p, 75

640

768

, composite signal

480 dot

576 dot, 720 480 dot *1

Connector for external connection

BNC connector

RGB input method -

GT16M-R2

-

-

-

-

-

-

Analog RGB(XGA:1024 768 dot,

SVGA: 800 600 dot,

VGA:640 480 dot)

Number of video input channels

Input image signal

Synchronizing signal

Display size -

-

-

1 channel

1Vp-p, 75

TTL, 1k

2 channels

*3

1024 768 dot (refresh rate 60Hz)

800 600 dot (refresh rate 60, 72,

75Hz)

640 480 dot (refresh rate 60, 72,

75, 85Hz)

Connector for external connection D-Sub15 pin: female

3.3

VDC

0.32A

0.51A

0.49A

Internal current consumption

Weight

5.0

VDC

0.34A accompanied with the

GT27-IF1000

0.34kg accompanied with the

GT27-IF1000

0.39A accompanied with the GT27-

IF1000

0.36kg accompanied with the GT27-

IF1000

0.35A accompanied with the

GT27-IF1000

0.33kg accompanied with the GT27-IF1000

*1:Compatible with PAL and CCIR formats only.

*2:The GOT cannot display both video images and RGB screens at the same time.

*3:The GOT can display only one RGB screen.

3. PART NAMES AND EXTERNAL

DIMENSIONS

3.1 GT16 Video/RGB Input Unit, GT16 Video

Input Unit, and GT16 RGB Input Unit

The external dimensions for all the units are the same except the connector dimensions of the video input section and the RGB input section.

GT16M-V4R1-Z

1)

133 (5.24)

2) GT16M-V4R1-Z

GT16M-V4-Z

GT16M-R2-Z

3)

2)

7) GT16M-V4R1-Z

7)

6)

GT16M-V4-Z

18

(0.71)

18

(0.71)

34

(1.34)

26

(1.02)

19

(0.75)

5)

4)

44.5 (1.75)

GT27-IF1000

GOT main unit

6)

GT16M-R2-Z

18

(0.71)

18

(0.71)

34

(1.34)

45

(1.77)

5)

4)

No.

1)

2)

3)

4)

5)

6)

7)

6)

Name

Extension connector

Mounting screw

68.5

(2.70)

19

(0.75)

5)

Description

Unit : mm (inch)

Connector for connecting an extension unit

Screw for fixing the Video Interface Converter Unit

Rating plate -

Connector for RGB input Connector for connecting 9-core combined cables

Video connector

Interface connector

Video connector connected to the Video Interface

Converter Unit

Connector connected to the Video Interface Converter

Unit

Connector for video input Connector for connecting a coaxial cable

3.2 Video Interface Converter Unit

3)

4)

2)

21.5 (0.85)

6)

No.

1)

2)

3)

Name

Extension connector

Mounting screw

Rating plate

4) Video connector

5)

6)

Auxiliary extension connector

Interface connector

Unit : mm (inch)

5)

Description

Connector for connecting the GT16 Video/RGB Input

Unit, GT16 Video Input Unit, or GT16 RGB Input Unit

Screw for fixing the GOT

-

Video connector for connecting the GT16 Video/RGB

Input Unit, GT16 Video Input Unit, or GT16 RGB

Input Unit

Auxiliary extension connector connected to the GOT

Extension connector connected to the GOT

4. INSTALLATION AND REMOVAL PRO-

CEDURE

4.1 Unit Installation

The installation procedure for the video/RGB input unit is explained using the

GT2712.

1) Turn off the GOT.

2) Pull up the two hooks in the extension unit cover (two covers) of the GOT to remove the cover toward the opposite side of the hoots of the cover as a fulcrum.

3) Connect the Video Interface Converter Unit to the auxiliary extension interface and the extension interface on the GOT. After connecting it, tighten four mounting screws (26mm) with a torque of 0.36N•m to 0.48N•m to fix the unit.

4)The connector for video input has the protection cap.

Remove the protection cap for the connector to be used.

(Store the removed protection cap.)

5) Fit the GT16 video/RGB input unit n the Video Interface Converter Unit case.

6) Tighten four mounting screws (40mm) of GT16 video/RGB input unit with a torque of 0.36N•m to 0.48N•m to fix the unit.

8) For mounting no extension unit on the unit, cover over four mounting screws with the accessory stickers to the GT16 video/RGB input unit, the GT16 video/

RGB input unit, or the Video Interface Converter Unit to avoid static electricity.

Keep the connector cover fixed.

Keep all the stickers fixed.

Connector cover Accessory sticker

Sticker

Accessory sticker

4.2 Unit Removal

For removing the Video/RGB Input Unit, Video Input Unit, and RGB Input Unit, reverse the procedure of the installation.

Warranty

Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi; machine damage or lost profits caused by faults in the Mitsubishi products; damage, secondary damage, accident compensation caused by special factors unpredictable by Mitsubishi; damages to products other than

Mitsubishi products; and to other duties.

For safe use

• This product has been manufactured as a general-purpose part for general industries, and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life.

• Before using the product for special purposes such as nuclear power, electric power, aerospace, medicine or passenger movement vehicles, consult with Mitsubishi.

• This product has been manufactured under strict quality control.

However, when installing the product where major accidents or losses could occur if the product fails, install appropriate backup or failsafe functions in the system.

Country/Region Sales office/Tel

Italy

Spain

U.S.A

Brazil

Germany

U.K

Mitsubishi Electric Automation Inc.

500 Corporate Woods Parkway Vernon Hills, IL 60061, U.S.A.

Tel : +1-847-478-2100

MELCO-TEC Rep. Com.e Assessoria Tecnica Ltda.

Rua Correia Dias, 184, Edificio Paraiso Trade Center-8 andar

Paraiso, Sao Paulo, SP Brazil

Tel : +55-11-5908-8331

Mitsubishi Electric Europe B.V. German Branch

Gothaer Strasse 8 D-40880 Ratingen, GERMANY

Tel : +49-2102-486-0

Mitsubishi Electric Europe B.V. UK Branch

Travellers Lane, Hatfield, Hertfordshire., AL10 8XB, U.K.

Tel : +44-1707-276100

Mitsubishi Electric Europe B.V. Italian Branch

Centro Dir. Colleoni, Pal. Perseo-Ingr.2

Via Paracelso 12, I-20041 Agrate Brianza., Milano, Italy

Tel : +39-039-60531

Mitsubishi Electric Europe B.V. Spanish Branch

Carretera de Rubi 76-80,

E-08190 Sant Cugat del Valles, Barcelona, Spain

Tel : +34-93-565-3131

France

South Africa

Hong Kong

Mitsubishi Electric Europe B.V. French Branch

25, Boulevard des Bouvets, F-92741 Nanterre Cedex, France

Tel : +33-1-5568-5568

Circuit Breaker Industries Ltd.

Private Bag 2016, ZA-1600 Isando, South Africa

Tel : +27-11-928-2000

Mitsubishi Electric Automation (Hong Kong) Ltd.

10th Floor, Manulife Tower, 169 Electric

Road, North Point, Hong Kong

Tel : +852-2887-8870

China

Taiwan

Korea

Mitsubishi Electric Automation (China) Ltd.

4/F Zhi Fu Plazz, No.80 Xin Chang Road,

Shanghai 200003, China

Tel : +86-21-6120-0808

Setsuyo Enterprise Co., Ltd.

6F No.105 Wu-Kung 3rd.Rd, Wu-Ku Hsiang,

Taipei Hsine, Taiwan

Tel : +886-2-2299-2499

Mitsubishi Electric Automation Korea Co., Ltd.

1480-6, Gayang-dong, Gangseo-ku Seoul

157-200,

Singapore

Tel : +82-2-3660-9552

Mitsubishi Electric Asia Pte, Ltd.

Thailand

Indonesia

307 Alexandra Road #05-01/02,

Mitsubishi Electric Building, Singapore 159943

Tel : +65-6470-2460

Mitsubishi Electric Automation (Thailand) Co., Ltd.

Bang-Chan Industrial Estate No.111 Moo 4, Serithai Rd,

T.Kannayao, A.Kannayao, Bangkok 10230 Thailand

Tel : +66-2-517-1326

P.T. Autoteknindo Sumber Makmur

Muara Karang Selatan, Block A/Utara

India

No.1 Kav. No.11 Kawasan Industri Pergudangan

Jakarta - Utara 14440, P.O.Box 5045 Jakarta, 11050 Indonesia

Tel : +62-21-6630833

Messung Systems Pvt, Ltd.

Electronic Sadan NO:III Unit No15, M.I.D.C Bhosari,

Pune-411026,

Australia

Tel : +91-20-2712-3130

Mitsubishi Electric Australia Pty. Ltd.

348 Victoria Road, Rydalmere, N.S.W 2116, Australia

Tel : +61-2-9684-7777

HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN

When exported from Japan, this manual does not require application to the Ministry of Economy, Trade and Industry for service transaction permission.

Specifications subject to change without notice.

Printed in Japan, July 2014.