Untitled

Untitled
Test Report issued under the responsibility of:
TEST REPORT
IEC 60950-1: 2005 (2nd Edition) and/or EN 60950-1:2006
Information technology equipment – Safety –
Part 1: General requirements
Report Reference No...................... :
11019890 001
Date of issue .................................... :
March 11, 2010
Total number of pages ......................
68
CB/CCA Testing Laboratory.......... :
TÜV Rheinland Taiwan Ltd., Taichung Laboratory
Address ............................................ :
10F, No. 219, Min Chuan Road, Taichung 403, Taiwan
Applicant’s name............................ :
Micro-Star Int’l Co., Ltd.
Address ............................................ :
69, Li-De St., Chung Ho City, Taipei Hsien 235 Taiwan
Manufacturer’s name ..................... :
Same as applicant.
Address ............................................ :
Same as applicant.
Factory’s name ............................... :
See the following pages.
Address ............................................ :
See the following pages.
Test specification:
Standard ........................................... :
IEC 60950-1:2005 (2nd Edition) and/or
EN 60950-1:2006 + A11:2009
Test procedure ................................. :
CB
Non-standard test method…………..:
N/A
Test Report Form No...................... :
IECEN60950_1C
Test Report Form(s) Originator ........ :
SGS Fimko Ltd
Master TRF ...................................... :
Dated 2007-06
Copyright © 2006 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as
copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from
the reader's interpretation of the reproduced material due to its placement and context.
If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB Scheme
procedure shall be removed.
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended
to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
If this Test Report Form is used by non-CCA members, the CIG logo and the reference to the CCA Procedure shall be
removed.
This report is not valid as a CCA Test Report unless signed by an approved CCA Testing Laboratory and
appended to a CCA Test Certificate issued by an NCB in accordance with CCA
Test item description ..................... :
All in one PC
Trade Mark ....................................... :
Manufacturer .................................... :
Same as applicant.
Model/Type reference ...................... :
MS-AE1XXXX (X= any alphanumeric character or blank)
Ratings ............................................. :
I/P: 19Vdc, 9.5A
Page 3 of 68
Report No. 11019890 001
Summary of testing:
Tests performed (name of test and test clause):
All applicable tests as described in Test Case and
Measurement Sections were performed.
• The maximum ambient temperature is specified as
40°C.
Testing location:
All tests as described in Test Case were
performed at the laboratory described on page
1.
• The CPU: Intel® Pentium® E5400 2.7GHz and
4.0GB memory are provided during tests.
• The user’s manual stated as below:
“The cable shield shall be earthed in accordance with
the building installation of National requirement.”
• The load conditions used during testing: Maximum
brightness and contrast of the LCD backlight circuit,
CPU are running 100%, reading and writing between
HDD and card reader, optical device playing a disk,
the dummy loads of 0.5A in each USB ports.
• Pre-production without serial number.
Summary of compliance with National Differences:
EU Group Differences, EU Special National Conditions, EU A-Deviations, AT, AU, CA, CH, DE, DK, FI, FR,
GB, IT, KR, NL, NO, PL, SE, SI, US.
Explanation of used codes: AT=Austria, AU=Australia, CA=Canada, CH=Switzerland, DE=Germany,
DK=Denmark, FI=Finland, FR=France, GB=United Kingdom, IT=Italy, KR=Korea, NL=The Netherlands,
NO=Norway, PL=Poland, SE=Sweden, SI=Slovenia, US=United States of America.
For National Differences see corresponding Attachment.
TRF No. IECEN60950_1C
Page 4 of 68
Report No. 11019890 001
Copy of marking plate:
TRF No. IECEN60950_1C
Page 5 of 68
Report No. 11019890 001
Test item particulars .................................................. :
Equipment mobility .................................................... : [X] movable
[] stationary
[] hand-held
[] transportable
[] for building-in [] direct plug-in
Connection to the mains............................................ : [] pluggable equipment [] permanent connection
[] detachable power supply cord
[] non-detachable power supply cord
[X] not directly connected to the mains
Operating condition ................................................... : [X] continuous
[] rated operating / resting time:
Access location ........................................................ : [X] operator accessible
[] restricted access location
Over voltage category (OVC) ................................... : [] OVC I [] OVC II [] OVC III [] OVC IV
[X] other: No direct mains connection
Mains supply tolerance (%) or absolute mains supply
values ....................................................................... : N/A
Tested for IT power systems .................................... : [] Yes
[X] No
IT testing, phase-phase voltage (V) ......................... : N/A
Class of equipment ................................................... : [] Class I [] Class II
[] Not classified
[X] Class III
Considered current rating (A) ................................... : Not directly connected to the mains
Pollution degree (PD) ............................................... : [] PD 1
[X] PD 2
[] PD 3
IP protection class .................................................... : IPX0
Altitude during operation (m) .................................... : Up to 2000
Altitude of test laboratory (m) ................................... : Up to 2000
Mass of equipment (kg) ............................................ : 5.15
Possible test case verdicts:
- test case does not apply to the test object.................: N/A
- test object does meet the requirement.......................: P (Pass)
- test object does not meet the requirement.................: F (Fail)
Testing ......................................................................... :
Date of receipt of test item ............................................: February – March, 2010
Date(s) of performance of tests ....................................: February – March, 2010
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(See Enclosure #)" refers to additional information appended to the report.
"(See appended table)" refers to a table appended to the report.
Note: This TRF includes EN Group Differences together with National Differences and Special
National Conditions, if any. All Differences are located in the Appendix to the main body of this TRF.
Throughout this report a point is used as the decimal separator.
TRF No. IECEN60950_1C
Page 6 of 68
Report No. 11019890 001
General product information:
•
The equipment under test (EUT) model MS-AE1XXXX is all in one PC for use in the scope of information
technology equipment.
• Motherboard type: MS-AE111.
Engineering Considerations
•
The product was submitted and tested for use at the maximum ambient temperature (Tma) permitted
by the manufacturer’s specification of: 40°C.
•
The following accessible locations are within a limited current circuit (see subclause 2.4): Output of
DC/AC inverter
•
The following circuit locations were investigated as a limited power source (see subclause 2.5): Output
ports.
The following terminals to be connected to a Cable Distribution System were investigated to Clause 7:
TV tuner
Additional Information
•
•
This end product is for use with field installable optical transceivers not provided with the product
when shipped from the original equipment manufacturer. This end product was evaluated with
representative optical transceivers during the type test investigation. The end product with optical
transceivers installed is required to comply with IEC 60950-1 and IEC 60825-1 and –2, including any
declared national differences. The decision on certification of the end product without the optical
transceivers rests with the recognizing NCB.
•
This report contains all national deviation as the class III equipment itself is subject of this CB report,
but CB countries should investigate this matter for external adapter while the equipment under test is
submitted for national approval.
•
The Label in Copy of marking plate is a draft of an artwork pending approval by National Certification
Bodies and it shall not be affixed to products prior to such an approval.
•
The power supply unit used with the product is a certified product which was investigated according to
the standard of earlier version. The suitability of use has been evaluated in this report.
Some components are pre-certified, which have been evaluated according to the relevant
requirements of IEC 60950-1, are employed in this product. Their suitability of use has been checked
according to subclauses 1.5.1 and 1.5.2.
Markings and Instructions
•
•
(IEC 60417-5009) for the stand-by condition. (See subclause 1.7.8.3)
Other comments:
Factory(ies):
MSI Computer (Shenzhen) Co., Ltd.
Longma Information Technology Industrial Park, Tangtou Village Shiyan Town, Baoan District, Shenzhen,
Guangdong 518108, P.R. China
Definition of variable(s):
Variable:
Range of variable:
Content:
X
any alphanumeric character or blank
For marketing purpose.
Attachments to this Test Report:
- Photo Documentation
- National Differences
- Measurement Section
TRF No. IECEN60950_1C
Page 7 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
1
GENERAL
P
1.5
Components
P
1.5.1
General
See below.
P
Comply with IEC 60950 or relevant component
standard
(see appended table 1.5.1)
P
1.5.2
Evaluation and testing of components
Components certified to IEC
standards and/or their
harmonized standards, are
used within their ratings and
are checked for correct
application.
P
1.5.3
Thermal controls
N/A
1.5.4
Transformers
N/A
1.5.5
Interconnecting cables
Interconnection cable to power
adaptor is only carrying SELV
on an energy level below
240VA.
Verdict
P
Except for the insulation
material there are no further
requirements to the
interconnection cable.
1.5.6
Capacitors bridging insulation
N/A
1.5.7
Resistors bridging insulation
N/A
1.5.7.1
Resistors bridging functional, basic or
supplementary insulation
N/A
1.5.7.2
Resistors bridging double or reinforced insulation
between a.c. mains and other circuits
N/A
1.5.7.3
Resistors bridging double or reinforced insulation
between a.c. mains and antenna or coaxial cable
N/A
1.5.8
Components in equipment for IT power systems
N/A
1.5.9
Surge suppressors
N/A
1.5.9.1
General
N/A
1.5.9.2
Protection of VDRs
N/A
1.5.9.3
Bridging of functional insulation by a VDR
N/A
1.5.9.4
Bridging of basic insulation by a VDR
N/A
1.5.9.5
Bridging of supplementary, double or reinforced
insulation by a VDR
N/A
1.6
Power interface
TRF No. IECEN60950_1C
P
Page 8 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
1.6.1
AC power distribution systems
No direct mains connection
N/A
1.6.2
Input current
(see appended table 1.6.2)
P
1.6.3
Voltage limit of hand-held equipment
1.6.4
Neutral conductor
1.7
Marking and instructions
1.7.1
Power rating
P
Equipment is not directly
connected to the AC mains
supply.
N/A
P
The power rating marking is
provided and is readily visible in
operator access area.
P
Rated voltage(s) or voltage range(s) (V) ...............: No direct connection to the
mains supply.
N/A
Symbol for nature of supply, for d.c. only ...............:
N/A
Rated frequency or rated frequency range (Hz) ....: No direct connection to the
mains supply.
N/A
Rated current (mA or A) ........................................: No direct connection to the
mains supply.
N/A
Manufacturer’s name or trade-mark or
See copy of marking plate.
identification mark ..................................................:
P
Model identification or type reference ...................: See copy of marking plate.
P
Symbol for Class II equipment only .......................:
N/A
Other markings and symbols .................................: Other markings and symbols
do not give rise to
misunderstanding.
P
1.7.2
Safety instructions and marking
See below.
P
1.7.2.1
General
Instructions are available.
P
1.7.2.2
Disconnect devices
1.7.2.3
Overcurrent protective device
N/A
1.7.2.4
IT power distribution systems
N/A
1.7.2.5
Operator access with a tool
N/A
1.7.2.6
Ozone
N/A
1.7.3
Short duty cycles
N/A
1.7.4
Supply voltage adjustment ....................................:
N/A
Methods and means of adjustment; reference to
installation instructions ..........................................:
N/A
Power outlets on the equipment ............................:
N/A
1.7.5
TRF No. IECEN60950_1C
P
Page 9 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
1.7.6
Fuse identification (marking, special fusing
characteristics, cross-reference) ...........................:
N/A
1.7.7
Wiring terminals
N/A
1.7.7.1
Protective earthing and bonding terminals ............:
N/A
1.7.7.2
Terminals for a.c. mains supply conductors
N/A
1.7.7.3
Terminals for d.c. mains supply conductors
N/A
1.7.8
Controls and indicators
1.7.8.1
Identification, location and marking .......................: The function of indicators and
controls is clearly identified.
P
1.7.8.2
Colours .................................................................: Colors are used and safety is
not involved.
P
1.7.8.3
Symbols according to IEC 60417 ...........................: See General product
information - Markings and
Instructions
P
1.7.8.4
Markings using figures ..........................................:
N/A
1.7.9
Isolation of multiple power sources .......................:
N/A
1.7.10
Thermostats and other regulating devices ............:
N/A
1.7.11
Durability
Marking is legible. The marking
plate has no curling and is not
able to be removed easily.
1.7.12
Removable parts
No removable parts.
1.7.13
Replaceable batteries ............................................: Warning text provided in user’s
manual.
P
Language(s) ...........................................................: English.

See below.
Verdict
P
P
N/A
N/A
1.7.14
Equipment for restricted access locations..............:
2
PROTECTION FROM HAZARDS
P
2.1
Protection from electric shock and energy hazards
P
2.1.1
Protection in operator access areas
2.1.1.1
Access to energized parts
P
Test by inspection ..................................................: The EUT is supplied from an
approved SPS adaptor that
provides only SELV.
P
Test with test finger (Figure 2A) ............................:
P
Test with test pin (Figure 2B) .................................:
P
Test with test probe (Figure 2C) ............................:
P
See below.
P
2.1.1.2
Battery compartments
N/A
2.1.1.3
Access to ELV wiring
N/A
TRF No. IECEN60950_1C
Page 10 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Working voltage (Vpeak or Vrms); minimum
distance through insulation (mm)
Verdict

2.1.1.4
Access to hazardous voltage circuit wiring
N/A
2.1.1.5
Energy hazards .....................................................: No energy hazard in operator
access area. The connectors of
the equipment below 240VA.
2.1.1.6
Manual controls
N/A
2.1.1.7
Discharge of capacitors in equipment
N/A
Measured voltage (V); time-constant (s) ................:
2.1.1.8
P

Energy hazards – d.c. mains supply
N/A
a) Capacitor connected to the d.c. mains supply ..:
N/A
b) Internal battery connected to the d.c. mains
supply ....................................................................:
N/A
2.1.1.9
Audio amplifiers .....................................................:
N/A
2.1.2
Protection in service access areas
N/A
2.1.3
Protection in restricted access locations
N/A
2.2
SELV circuits
2.2.1
General requirements
2.2.2
Voltages under normal conditions (V) ...................:
P
2.2.3
Voltages under fault conditions (V) .......................:
P
2.2.4
Connection of SELV circuits to other circuits ......:
2.3
TNV circuits
N/A
2.3.1
Limits
N/A
P
The equipment supplied by
external power adaptor which
provides SELV only.
See 2.2.2, 2.2.3 and 2.4.3.
No direct connection between
SELV and any primary circuits.
P
P
Type of TNV circuits ...............................................:

2.3.2
Separation from other circuits and from accessible
parts
N/A
2.3.2.1
General requirements
N/A
2.3.2.2
Protection by basic insulation
N/A
2.3.2.3
Protection by earthing
N/A
2.3.2.4
Protection by other constructions ..........................:
N/A
2.3.3
Separation from hazardous voltages
N/A
TRF No. IECEN60950_1C
Page 11 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Insulation employed................................................:
2.3.4
Verdict

Connection of TNV circuits to other circuits
N/A
Insulation employed................................................:

2.3.5
Test for operating voltages generated externally
N/A
2.4
Limited current circuits
2.4.1
General requirements
See below.
P
2.4.2
Limit values
The peak drop voltage was
measured with an oscilloscope
at a 2kΩ non-inductive
resistor.
P
P
Frequency (Hz) .......................................................: See appended table 2.4.2.

Measured current (mA)...........................................: See appended table 2.4.2.

Measured voltage (V) .............................................: See appended table 2.4.2.

Measured circuit capacitance (nF or µF)................: Less than 0.1µF.

2.4.3
Connection of limited current circuits to other
circuits
P
2.5
Limited power sources
Complied.
P
a) Inherently limited output
b) Impedance limited output
N/A
Approved sources of
polyswitch provided. See
appended table 1.5.1 for
details.
P
c) Regulating network limited output under normal
operating and single fault condition
N/A
d) Overcurrent protective device limited output
N/A
Max. output voltage (V), max. output current (A),
Results see appended table
max. apparent power (VA)......................................: 2.5.

Current rating of overcurrent protective device (A)

2.6
Provisions for earthing and bonding
N/A
2.6.1
Protective earthing
N/A
2.6.2
Functional earthing
N/A
2.6.3
Protective earthing and protective bonding
conductors
N/A
2.6.3.1
General
N/A
2.6.3.2
Size of protective earthing conductors
N/A
TRF No. IECEN60950_1C
Page 12 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
2
Rated current (A), cross-sectional area (mm ),
AWG .......................................................................:
2.6.3.3
Size of protective bonding conductors
Verdict

N/A
2
Rated current (A), cross-sectional area (mm ),
AWG .......................................................................:

Protective current rating (A), cross-sectional area
2
(mm ), AWG ...........................................................:
2.6.3.4
Resistance of earthing conductors and their
terminations; resistance (Ω), voltage drop (V), test
current (A), duration (min) ......................................:
N/A
2.6.3.5
Colour of insulation.................................................:
N/A
2.6.4
Terminals
N/A
2.6.4.1
General
N/A
2.6.4.2
Protective earthing and bonding terminals
N/A
Rated current (A), type, nominal thread diameter
(mm) .......................................................................:

2.6.4.3
Separation of the protective earthing conductor
from protective bonding conductors
N/A
2.6.5
Integrity of protective earthing
N/A
2.6.5.1
Interconnection of equipment
N/A
2.6.5.2
Components in protective earthing conductors and
protective bonding conductors
N/A
2.6.5.3
Disconnection of protective earth
N/A
2.6.5.4
Parts that can be removed by an operator
N/A
2.6.5.5
Parts removed during servicing
N/A
2.6.5.6
Corrosion resistance
N/A
2.6.5.7
Screws for protective bonding
N/A
2.6.5.8
Reliance on telecommunication network or cable
distribution system
N/A
2.7
Overcurrent and earth fault protection in primary circuits
N/A
2.7.1
Basic requirements
N/A
Instructions when protection relies on building
installation
N/A
2.7.2
Faults not simulated in 5.3.7
N/A
2.7.3
Short-circuit backup protection
N/A
2.7.4
Number and location of protective devices ...........:
N/A
TRF No. IECEN60950_1C
Page 13 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
2.7.5
Protection by several devices
N/A
2.7.6
Warning to service personnel ................................:
N/A
2.8
Safety interlocks
N/A
2.8.1
General principles
N/A
2.8.2
Protection requirements
N/A
2.8.3
Inadvertent reactivation
N/A
2.8.4
Fail-safe operation
N/A
2.8.5
Moving parts
N/A
2.8.6
Overriding
N/A
2.8.7
Switches and relays
N/A
2.8.7.1
Contact gaps (mm) ................................................:
N/A
2.8.7.2
Overload test
N/A
2.8.7.3
Endurance test
N/A
2.8.7.4
Electric strength test
N/A
2.8.8
Mechanical actuators
N/A
2.9
Electrical insulation
2.9.1
Properties of insulating materials
Natural rubber, asbestos or
hygroscopic material is not
used.
P
2.9.2
Humidity conditioning
120 hours
P
P
Relative humidity (%), temperature (°C) ................: 95% R.H, 40°C

2.9.3
Grade of insulation
P
2.9.4
Separation from hazardous voltages
P
Method(s) used ......................................................: 1

The adequate levels of safety
insulation is provided and
maintained to comply with the
requirements of this standard.
2.10
Clearances, creepage distances and distances through insulation
N/A
2.10.1
General
N/A
2.10.1.1
Frequency ..............................................................:
N/A
2.10.1.2
Pollution degrees ...................................................:
N/A
2.10.1.3
Reduced values for functional insulation
N/A
2.10.1.4
Intervening unconnected conductive parts
N/A
TRF No. IECEN60950_1C
Page 14 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
2.10.1.5
Insulation with varying dimensions
N/A
2.10.1.6
Special separation requirements
N/A
2.10.1.7
Insulation in circuits generating starting pulses
N/A
2.10.2
Determination of working voltage
N/A
2.10.2.1
General
N/A
2.10.2.2
RMS working voltage
N/A
2.10.2.3
Peak working voltage
N/A
2.10.3
Clearances
N/A
2.10.3.1
General
N/A
2.10.3.2
Mains transient voltages
N/A
a) AC mains supply ...............................................:
N/A
b) Earthed d.c. mains supplies ..............................:
N/A
c) Unearthed d.c. mains supplies ..........................:
N/A
d) Battery operation ...............................................:
N/A
2.10.3.3
Clearances in primary circuits
N/A
2.10.3.4
Clearances in secondary circuits
N/A
2.10.3.5
Clearances in circuits having starting pulses
N/A
2.10.3.6
Transients from a.c. mains supply .........................:
N/A
2.10.3.7
Transients from d.c. mains supply .........................:
N/A
2.10.3.8
Transients from telecommunication networks and
cable distribution systems .....................................:
N/A
2.10.3.9
Measurement of transient voltage levels
N/A
a) Transients from a mains supply
N/A
For an a.c. mains supply .......................................:
N/A
For a d.c. mains supply .........................................:
N/A
b) Transients from a telecommunication network .:
N/A
2.10.4
Creepage distances
N/A
2.10.4.1
General
N/A
2.10.4.2
Material group and comparative tracking index
N/A
CTI tests .................................................................:
Result - Remark
Verdict

2.10.4.3
Minimum creepage distances
N/A
2.10.5
Solid insulation
N/A
2.10.5.1
General
N/A
2.10.5.2
Distances through insulation
N/A
2.10.5.3
Insulating compound as solid insulation
N/A
TRF No. IECEN60950_1C
Page 15 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
2.10.5.4
Semiconductor devices
N/A
2.10.5.5.
Cemented joints
N/A
2.10.5.6
Thin sheet material – General
N/A
2.10.5.7
Separable thin sheet material
N/A
Number of layers (pcs) ..........................................:
Result - Remark
Verdict

2.10.5.8
Non-separable thin sheet material
N/A
2.10.5.9
Thin sheet material – standard test procedure
N/A
Electric strength test
2.10.5.10
Thin sheet material – alternative test procedure
Electric strength test

N/A

2.10.5.11
Insulation in wound components
N/A
2.10.5.12
Wire in wound components
N/A
Working voltage .....................................................:
N/A
a) Basic insulation not under stress ......................:
N/A
b) Basic, supplementary, reinforced insulation ......:
N/A
c) Compliance with Annex U .................................:
N/A
Two wires in contact inside wound component;
angle between 45° and 90° ...................................:
N/A
Wire with solvent-based enamel in wound
components
N/A
2.10.5.13
Electric strength test

Routine test
N/A
Additional insulation in wound components
N/A
Working voltage .....................................................:
N/A
- Basic insulation not under stress ........................:
N/A
- Supplementary, reinforced insulation ..................:
N/A
2.10.6
Construction of printed boards
N/A
2.10.6.1
Uncoated printed boards
N/A
2.10.6.2
Coated printed boards
N/A
2.10.6.3
Insulation between conductors on the same inner
surface of a printed board
N/A
2.10.6.4
Insulation between conductors on different layers
of a printed board
N/A
Distance through insulation
N/A
Number of insulation layers (pcs) ..........................:
N/A
Component external terminations
N/A
2.10.5.14
2.10.7
TRF No. IECEN60950_1C
Page 16 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
2.10.8
Tests on coated printed boards and coated
components
N/A
2.10.8.1
Sample preparation and preliminary inspection
N/A
2.10.8.2
Thermal conditioning
N/A
2.10.8.3
Electric strength test
N/A
2.10.8.4
Abrasion resistance test
N/A
2.10.9
Thermal cycling
N/A
2.10.10
Test for Pollution Degree 1 environment and
insulating compound
N/A
2.10.11
Tests for semiconductor devices and cemented
joints
N/A
2.10.12
Enclosed and sealed parts
N/A
3
WIRING, CONNECTIONS AND SUPPLY
P
3.1
General
P
3.1.1
Current rating and overcurrent protection
All internal wires are UL
recognized wiring which is
PVC insulated, rated VW-1,
minimum 80°C. Internal wiring
gauge is suitable for current
intended to be carried.
P
3.1.2
Protection against mechanical damage
Wires do not touch sharp
edges, which could damage
the insulation.
P
3.1.3
Securing of internal wiring
Internal wires are secured by
quick connection, so that a
loosening of the terminal
connection is unlikely.
P
3.1.4
Insulation of conductors
The insulation of the individual
conductors is suitable for the
application and the working
voltage. For the insulation
material see 3.1.1.
P
3.1.5
Beads and ceramic insulators
N/A
3.1.6
Screws for electrical contact pressure
N/A
3.1.7
Insulating materials in electrical connections
N/A
3.1.8
Self-tapping and spaced thread screws
No self- tapping or spaced
thread screws are used.
N/A
3.1.9
Termination of conductors
All conductors are reliably
secured.
P
TRF No. IECEN60950_1C
Result - Remark
Verdict
Page 17 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
10 N pull test
10N pull test performed for all
relevant conductors. No
hazards caused hereby.
Verdict
P
3.1.10
Sleeving on wiring
N/A
3.2
Connection to a mains supply
N/A
3.2.1
Means of connection
N/A
3.2.1.1
Connection to an a.c. mains supply
N/A
3.2.1.2
Connection to a d.c. mains supply
N/A
3.2.2
Multiple supply connections
N/A
3.2.3
Permanently connected equipment
N/A
Number of conductors, diameter of cable and
conduits (mm) ........................................................:

3.2.4
Appliance inlets
N/A
3.2.5
Power supply cords
N/A
3.2.5.1
AC power supply cords
N/A
Type .......................................................................:

Rated current (A), cross-sectional area (mm²),
AWG ......................................................................:

3.2.5.2
DC power supply cords
N/A
3.2.6
Cord anchorages and strain relief
N/A
Mass of equipment (kg), pull (N) ..........................:

Longitudinal displacement (mm) ...........................:

3.2.7
Protection against mechanical damage
N/A
3.2.8
Cord guards
N/A
Diameter or minor dimension D (mm); test mass
(g) ..........................................................................:

Radius of curvature of cord (mm)...........................:

3.2.9
Supply wiring space
N/A
3.3
Wiring terminals for connection of external conductors
N/A
3.3.1
Wiring terminals
N/A
3.3.2
Connection of non-detachable power supply cords
N/A
3.3.3
Screw terminals
N/A
3.3.4
Conductor sizes to be connected
N/A
TRF No. IECEN60950_1C
Page 18 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Rated current (A), cord/cable type, cross-sectional
2
area (mm )..............................................................:
3.3.5
Verdict

Wiring terminal sizes
N/A
Rated current (A), type, nominal thread diameter
(mm) ......................................................................:

3.3.6
Wiring terminal design
N/A
3.3.7
Grouping of wiring terminals
N/A
3.3.8
Stranded wire
N/A
3.4
Disconnection from the mains supply
N/A
3.4.1
General requirement
N/A
3.4.2
Disconnect devices
N/A
3.4.3
Permanently connected equipment
N/A
3.4.4
Parts which remain energized
N/A
3.4.5
Switches in flexible cords
N/A
3.4.6
Number of poles - single-phase and d.c.
equipment
N/A
3.4.7
Number of poles - three-phase equipment
N/A
3.4.8
Switches as disconnect devices
N/A
3.4.9
Plugs as disconnect devices
N/A
3.4.10
Interconnected equipment
N/A
3.4.11
Multiple power sources
N/A
3.5
Interconnection of equipment
3.5.1
General requirements
3.5.2
Types of interconnection circuits ...........................: Interconnection circuits of
SELV and LCC through
secondary output connector.
3.5.3
ELV circuits as interconnection circuits
No ELV interconnection circuit.
3.5.4
Data ports for additional equipment
See appended table 2.5.
4
PHYSICAL REQUIREMENTS
4.1
Stability
Angle of 10°
Test force (N) .........................................................:
TRF No. IECEN60950_1C
P
Conformance to 2.2 is
continued.
P
P
N/A
P
P
N/A
The equipment mass less than
7kg.
N/A
N/A
Page 19 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
4.2
Mechanical strength
4.2.1
General
4.2.2
Steady force test, 10 N
N/A
4.2.3
Steady force test, 30 N
N/A
4.2.4
Steady force test, 250 N
250N applied to outer
enclosure. No energy or other
hazards.
P
4.2.5
Impact test
See below.
P
Fall test
No hazard as result from steel
ball fall test.
P
Swing test
No hazard as result from steel
ball swing test.
P
P
See below. After tests, unit
complies with 4.4.1.
P
4.2.6
Drop test; height (mm) ...........................................: No hazard as result from
1000mm drop test.
P
4.2.7
Stress relief test
P
4.2.8
Cathode ray tubes
N/A
Picture tube separately certified ............................:
N/A
4.2.9
High pressure lamps
N/A
4.2.10
Wall or ceiling mounted equipment; force (N) .......: 151.5N applied for downward
through the geometric centre.
No damage and hazards.
P
4.3
Design and construction
P
4.3.1
Edges and corners
4.3.2
Handles and manual controls; force (N).................:
4.3.3
Adjustable controls
None that would cause hazard.
N/A
4.3.4
Securing of parts
Electrical and mechanical
connections can be expected
to withstand usual mechanical
stress.
P
4.3.5
Connection by plugs and sockets
Mismatch of connectors were
prevented by incompatible
form or location.
P
4.3.6
Direct plug-in equipment
Not direct plug-in type.
TRF No. IECEN60950_1C
Test performed at 71°C for
7 hours. No safety relevant
damages of the enclosure.
Edges and corners of the
enclosure are rounded.
P
N/A
N/A
Page 20 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
Torque ...................................................................:

Compliance with the relevant mains plug standard
................................................................................:
N/A
4.3.7
Heating elements in earthed equipment
N/A
4.3.8
Batteries
Approved battery used and
which was protected by a
circuit.
- D5 short= 3.0mA
- R198 short= 0mA
P
- Overcharging of a rechargeable battery
N/A
- Unintentional charging of a non-rechargeable
battery
N/A
- Reverse charging of a rechargeable battery
N/A
- Excessive discharging rate for any battery
N/A
4.3.9
Oil and grease
N/A
4.3.10
Dust, powders, liquids and gases
N/A
4.3.11
Containers for liquids or gases
N/A
4.3.12
Flammable liquids ..................................................:
N/A
Quantity of liquid (l) ................................................:
N/A
Flash point (°C) ......................................................:
N/A
4.3.13
Radiation
4.3.13.1
General
4.3.13.2
Ionizing radiation
4.3.13.3
4.3.13.4
No radiation is generated
inside the equipment. The
energy of the indicator LED is
far below the limit for Class 1
Laser products.
For other component refer to
appended table 1.5.1.
P
P
N/A
Measured radiation (pA/kg) ...................................:

Measured high-voltage (kV) ..................................:

Measured focus voltage (kV) .................................:

CRT markings ........................................................:

Effect of ultraviolet (UV) radiation on materials
N/A
Part, property, retention after test, flammability
classification ..........................................................:
N/A
Human exposure to ultraviolet (UV) radiation .......:
N/A
TRF No. IECEN60950_1C
Page 21 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
4.3.13.5
Laser (including LEDs)
The energy of the indicator
LED is far below the limit for
Class 1 LED products.
Laser class .............................................................: See above.
Verdict
P

4.3.13.6
Other types ............................................................:
N/A
4.4
Protection against hazardous moving parts
4.4.1
General
4.4.2
Protection in operator access areas ......................: Motor used in the appliance
are certified HDD, ODD.
The DC fan is located in the
notebook which blocked by
heaksink, therefore user can
not contact to any moving part
and course hazards.
4.4.3
Protection in restricted access locations ...............: Not limited for restricted
access locations.
N/A
4.4.4
Protection in service access areas
N/A
4.5
Thermal requirements
4.5.1
General
No exceeding temperature.
P
4.5.2
Temperature tests
(See appended table 4.5)
P
P
See below.
P
P
P
Normal load condition per Annex L .......................: (See Annex L)

4.5.3
Temperature limits for materials
(see appended table 4.5)
P
4.5.4
Touch temperature limits
(see appended table 4.5)
P
4.5.5
Resistance to abnormal heat .................................:
4.6
Openings in enclosures
P
4.6.1
Top and side openings
P
Dimensions (mm) ..................................................: See appended table 4.6.1 and
4.6.2.

Bottoms of fire enclosures
P
Construction of the bottom, dimensions (mm) .......: See appended table 4.6.1 and
4.6.2.

4.6.2
N/A
4.6.3
Doors or covers in fire enclosures
N/A
4.6.4
Openings in transportable equipment
N/A
4.6.4.1
Constructional design measures
N/A
Dimensions (mm) ..................................................:
TRF No. IECEN60950_1C

Page 22 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
4.6.4.2
Evaluation measures for larger openings
N/A
4.6.4.3
Use of metallized parts
N/A
4.6.5
Adhesives for constructional purposes
N/A
Conditioning temperature (°C), time (weeks) .........:

4.7
Resistance to fire
P
4.7.1
Reducing the risk of ignition and spread of flame
See below.
Method 1, selection and application of components (see appended table 1.5.1)
wiring and materials
Method 2, application of all of simulated fault
condition tests
P
P
N/A
4.7.2
Conditions for a fire enclosure
See below.
P
4.7.2.1
Parts requiring a fire enclosure
With having the following parts:
P
• Components in secondary
(not supplied by LPS)
• Insulated wiring
The fire enclosure is required.
4.7.2.2
Parts not requiring a fire enclosure
4.7.3
Materials
4.7.3.1
General
PCB rated accordingly. See
appended table 1.5.1 for
details.
P
4.7.3.2
Materials for fire enclosures
See appended table 1.5.1.
N/A
4.7.3.3
Materials for components and other parts outside
fire enclosures
4.7.3.4
Materials for components and other parts inside
fire enclosures
4.7.3.5
Materials for air filter assemblies
N/A
4.7.3.6
Materials used in high-voltage components
N/A
5
ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS
5.1
Touch current and protective conductor current
N/A
5.1.1
General
N/A
5.1.2
Configuration of equipment under test (EUT)
N/A
5.1.2.1
Single connection to an a.c. mains supply
N/A
5.1.2.2
Redundant multiple connections to an a.c. mains
supply
N/A
TRF No. IECEN60950_1C
N/A
P
N/A
The material is made of V-2,
HF-2 material.
N/A
P
Page 23 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
5.1.2.3
Simultaneous multiple connections to an a.c.
mains supply
N/A
5.1.3
Test circuit
N/A
5.1.4
Application of measuring instrument
N/A
5.1.5
Test procedure
N/A
5.1.6
Test measurements
N/A
Supply voltage (V) .................................................:

Measured touch current (mA) ................................:

Max. allowed touch current (mA) ...........................:

Measured protective conductor current (mA) ........:

Max. allowed protective conductor current (mA) ....:

5.1.7
Equipment with touch current exceeding 3,5 mA
N/A
5.1.7.1
General ..................................................................:
N/A
5.1.7.2
Simultaneous multiple connections to the supply
N/A
5.1.8
Touch currents to telecommunication networks and
cable distribution systems and from
telecommunication networks
N/A
5.1.8.1
Limitation of the touch current to a
telecommunication network or to a cable
distribution system
N/A
5.1.8.2
Supply voltage (V) .................................................:

Measured touch current (mA) ................................:

Max. allowed touch current (mA) ...........................:

Summation of touch currents from
telecommunication networks
N/A
a) EUT with earthed telecommunication ports ......:
N/A
b) EUT whose telecommunication ports have no
reference to protective earth
N/A
5.2
Electric strength
P
5.2.1
General
P
5.2.2
Test procedure
P
5.3
Abnormal operating and fault conditions
P
5.3.1
Protection against overload and abnormal
operation
TRF No. IECEN60950_1C
See below.
P
Page 24 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
5.3.2
Motors
Motor is used in the
appliances that are certified
HDD, ODD and DC fan, see
appended table 1.5.1.
5.3.3
Transformers
No safety isolation
transformer.
5.3.4
Functional insulation...............................................: Method c). Results see
appended table 5.3.
5.3.5
Electromechanical components
N/A
5.3.6
Audio amplifiers in ITE ...........................................:
N/A
5.3.7
Simulation of faults
5.3.8
Unattended equipment
5.3.9
Compliance criteria for abnormal operating and
fault conditions
See below.
P
5.3.9.1
During the tests
No fire occurred. No molten
metal was emitted.
P
5.3.9.2
After the tests
N/A
6
CONNECTION TO TELECOMMUNICATION NETWORKS
N/A
6.1
Protection of telecommunication network service persons, and users of other
equipment connected to the network, from hazards in the equipment
N/A
6.1.1
Protection from hazardous voltages
N/A
6.1.2
Separation of the telecommunication network from earth
N/A
6.1.2.1
Requirements
N/A
Results see appended table
5.3.
Verdict
P
N/A
P
P
N/A
Supply voltage (V) .................................................:

Current in the test circuit (mA) .............................:

6.1.2.2
Exclusions ..............................................................:
N/A
6.2
Protection of equipment users from overvoltages on telecommunication networks
N/A
6.2.1
Separation requirements
N/A
6.2.2
Electric strength test procedure
N/A
6.2.2.1
Impulse test
N/A
6.2.2.2
Steady-state test
N/A
6.2.2.3
Compliance criteria
N/A
6.3
Protection of the telecommunication wiring system from overheating
N/A
TRF No. IECEN60950_1C
Page 25 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
Max. output current (A) ..........................................:

Current limiting method .........................................:

7
CONNECTION TO CABLE DISTRIBUTION SYSTEMS
P
7.1
General
P
7.2
Protection of cable distribution system service
persons, and users of other equipment connected
to the system, from hazardous voltages in the
equipment
The cable distribution systems
are assumed as TNV-1.
P
7.3
Protection of equipment users from overvoltages
on the cable distribution system
Due to:
- The circuit under
consideration is TNV-1.
- The common of the circuit
and accessible is connected
to the screen of coaxial
cable.
- The screen of the coaxial
cable is intended to be
connected to earth in the
building insulation
Therefore the separation
requirement and tests of 6.2.1
is not applied.
P
7.4
Insulation between primary circuits and cable
distribution systems
P
7.4.1
General
P
7.4.2
Voltage surge test
Voltage surge test conducted.
See appended table 5.2.
P
7.4.3
Impulse test
Impulse test conducted. See
appended table 5.2.
P
A
ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE
N/A
A.1
Flammability test for fire enclosures of movable
equipment having a total mass exceeding 18 kg,
and of stationary equipment (see 4.7.3.2)
N/A
A.1.1
Samples..................................................................:

Wall thickness (mm) ...............................................:

A.1.2
Conditioning of samples; temperature (°C) ...........:
N/A
A.1.3
Mounting of samples .............................................:
N/A
A.1.4
Test flame (see IEC 60695-11-3)
N/A
Flame A, B, C or D ................................................:
TRF No. IECEN60950_1C

Page 26 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
A.1.5
Test procedure
N/A
A.1.6
Compliance criteria
N/A
Sample 1 burning time (s) ......................................:

Sample 2 burning time (s) ......................................:

Sample 3 burning time (s) ......................................:

A.2
Flammability test for fire enclosures of movable equipment having a total mass not
exceeding 18 kg, and for material and components located inside fire enclosures
(see 4.7.3.2 and 4.7.3.4)
A.2.1
Samples, material ...................................................:

Wall thickness (mm) ...............................................:

A.2.2
Conditioning of samples; temperature (°C) ...........:
N/A
A.2.3
Mounting of samples .............................................:
N/A
A.2.4
Test flame (see IEC 60695-11-4)
N/A
Flame A, B or C .....................................................:
N/A

A.2.5
Test procedure
N/A
A.2.6
Compliance criteria
N/A
A.2.7
Sample 1 burning time (s) ......................................:

Sample 2 burning time (s) ......................................:

Sample 3 burning time (s) ......................................:

Alternative test acc. to IEC 60695-11-5, cl. 5 and 9
N/A
Sample 1 burning time (s) ......................................:

Sample 2 burning time (s) ......................................:

Sample 3 burning time (s) ......................................:

A.3
Hot flaming oil test (see 4.6.2)
N/A
A.3.1
Mounting of samples
N/A
A.3.2
Test procedure
N/A
A.3.3
Compliance criterion
N/A
B
ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see 4.7.2.2 and
5.3.2)
N/A
B.1
General requirements
N/A
Position ..................................................................:

Manufacturer ..........................................................:

Type .......................................................................:

TRF No. IECEN60950_1C
Page 27 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Rated values .........................................................:
Result - Remark
Verdict

B.2
Test conditions
N/A
B.3
Maximum temperatures
N/A
B.4
Running overload test
N/A
B.5
Locked-rotor overload test
N/A
Test duration (days) ...............................................:

Electric strength test: test voltage (V) ....................:

B.6
Running overload test for d.c. motors in secondary
circuits
N/A
B.6.1
General
N/A
B.6.2
Test procedure
N/A
B.6.3
Alternative test procedure
N/A
B.6.4
Electric strength test; test voltage (V) ....................:
N/A
B.7
Locked-rotor overload test for d.c. motors in
secondary circuits
N/A
B.7.1
General
N/A
B.7.2
Test procedure
N/A
B.7.3
Alternative test procedure
N/A
B.7.4
Electric strength test; test voltage (V) ....................:
N/A
B.8
Test for motors with capacitors
N/A
B.9
Test for three-phase motors
N/A
B.10
Test for series motors
N/A
C
Operating voltage (V) ............................................:

ANNEX C, TRANSFORMERS (see 1.5.4 and 5.3.3)
N/A
Position ..................................................................:

Manufacturer ..........................................................:

Type .......................................................................:

Rated values .........................................................:

Method of protection...............................................:

C.1
Overload test
N/A
C.2
Insulation
N/A
Protection from displacement of windings..............:
N/A
TRF No. IECEN60950_1C
Page 28 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
D
ANNEX D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS
(see 5.1.4)
N/A
D.1
Measuring instrument
N/A
D.2
Alternative measuring instrument
N/A
E
ANNEX E, TEMPERATURE RISE OF A WINDING (see 1.4.13)
N/A
F
ANNEX F, MEASUREMENT OF CLEARANCES AND CREEPAGE DISTANCES
(see 2.10 and Annex G)
N/A
G
ANNEX G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM
CLEARANCES
N/A
G.1
Clearances
N/A
G.1.1
General
N/A
G.1.2
Summary of the procedure for determining
minimum clearances
N/A
G.2
Determination of mains transient voltage (V)
N/A
G.2.1
AC mains supply ....................................................:
N/A
G.2.2
Earthed d.c. mains supplies ..................................:
N/A
G.2.3
Unearthed d.c. mains supplies ..............................:
N/A
G.2.4
Battery operation ...................................................:
N/A
G.3
Determination of telecommunication network
transient voltage (V) ..............................................:
N/A
G.4
Determination of required withstand voltage (V)
N/A
G.4.1
Mains transients and internal repetitive peaks ......:
N/A
G.4.2
Transients from telecommunication networks .......:
N/A
G.4.3
Combination of transients
N/A
G.4.4
Transients from cable distribution systems
N/A
G.5
Measurement of transient voltages (V)
N/A
a) Transients from a mains supply
N/A
For an a.c. mains supply
N/A
For a d.c. mains supply
N/A
b) Transients from a telecommunication network
N/A
G.6
Determination of minimum clearances ..................:
N/A
H
ANNEX H, IONIZING RADIATION (see 4.3.13)
N/A
TRF No. IECEN60950_1C
Result - Remark
Verdict
Page 29 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
J
ANNEX J, TABLE OF ELECTROCHEMICAL POTENTIALS (see 2.6.5.6)
Metal(s) used .........................................................:
Verdict
N/A

K
ANNEX K, THERMAL CONTROLS (see 1.5.3 and 5.3.8)
N/A
K.1
Making and breaking capacity
N/A
K.2
Thermostat reliability; operating voltage (V) ..........:
N/A
K.3
Thermostat endurance test; operating voltage (V) :
N/A
K.4
Temperature limiter endurance; operating voltage
(V) ..........................................................................:
N/A
K.5
Thermal cut-out reliability
N/A
K.6
Stability of operation
N/A
L
ANNEX L, NORMAL LOAD CONDITIONS FOR SOME TYPES OF ELECTRICAL
BUSINESS EQUIPMENT (see 1.2.2.1 and 4.5.2)
L.1
Typewriters
N/A
L.2
Adding machines and cash registers
N/A
L.3
Erasers
N/A
L.4
Pencil sharpeners
N/A
L.5
Duplicators and copy machines
N/A
L.6
Motor-operated files
N/A
L.7
Other business equipment
M
ANNEX M, CRITERIA FOR TELEPHONE RINGING SIGNALS (see 2.3.1)
N/A
M.1
Introduction
N/A
M.2
Method A
N/A
M.3
Method B
N/A
M.3.1
Ringing signal
N/A
M.3.1.1
Frequency (Hz) ......................................................:

M.3.1.2
Voltage (V) .............................................................:

M.3.1.3
Cadence; time (s), voltage (V) ...............................:

M.3.1.4
Single fault current (mA) ........................................:

M.3.2
Tripping device and monitoring voltage .................:
N/A
M.3.2.1
Conditions for use of a tripping device or a
monitoring voltage
N/A
M.3.2.2
Tripping device
N/A
M.3.2.3
Monitoring voltage (V) ...........................................:
N/A
TRF No. IECEN60950_1C
See “summary of testing”.
P
P
Page 30 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
N
ANNEX N, IMPULSE TEST GENERATORS (see 1.5.7.2, 1.5.7.3, 2.10.3.9, 6.2.2.1,
7.3.2, 7.4.3 and Clause G.5)
N/A
N.1
ITU-T impulse test generators
N/A
N.2
IEC 60065 impulse test generator
N/A
P
ANNEX P, NORMATIVE REFERENCES
Q
ANNEX Q, Voltage dependent resistors (VDRs) (see 1.5.9.1)
N/A
a) Preferred climatic categories .............................:
N/A
b) Maximum continuous voltage ............................:
N/A
c) Pulse current .....................................................:
N/A
R
Annex R, EXAMPLES OF REQUIREMENTS FOR QUALITY CONTROL
PROGRAMMES
N/A
R.1
Minimum separation distances for unpopulated
coated printed boards (see 2.10.6.2)
N/A
R.2
Reduced clearances (see 2.10.3)
N/A
S
ANNEX S, PROCEDURE FOR IMPULSE TESTING (see 6.2.2.3)
N/A
S.1
Test equipment
N/A
S.2
Test procedure
N/A
S.3
Examples of waveforms during impulse testing
N/A
T
ANNEX T, GUIDANCE ON PROTECTION AGAINST INGRESS OF WATER
(see 1.1.2)
N/A


U
ANNEX U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED
INSULATION (see 2.10.5.4)
N/A

V
ANNEX V, AC POWER DISTRIBUTION SYSTEMS (see 1.6.1)
N/A
V.1
Introduction
N/A
V.2
TN power distribution systems
N/A
TRF No. IECEN60950_1C
Page 31 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
W
ANNEX W, SUMMATION OF TOUCH CURRENTS
N/A
W.1
Touch current from electronic circuits
N/A
W.1.1
Floating circuits
N/A
W.1.2
Earthed circuits
N/A
W.2
Interconnection of several equipments
N/A
W.2.1
Isolation
N/A
W.2.2
Common return, isolated from earth
N/A
W.2.3
Common return, connected to protective earth
N/A
X
ANNEX X, MAXIMUM HEATING EFFECT IN TRANSFORMER TESTS (see clause
C.1)
N/A
X.1
Determination of maximum input current
N/A
X.2
Overload test procedure
N/A
Y
ANNEX Y, ULTRAVIOLET LIGHT CONDITIONING TEST (see 4.3.13.3)
N/A
Y.1
Test apparatus .......................................................:
N/A
Y.2
Mounting of test samples .......................................:
N/A
Y.3
Carbon-arc light-exposure apparatus ....................:
N/A
Y.4
Xenon-arc light exposure apparatus .....................:
N/A
Z
ANNEX Z, OVERVOLTAGE CATEGORIES (see 2.10.3.2 and Clause G.2)
N/A
AA
ANNEX AA, MANDREL TEST (see 2.10.5.8)
N/A
BB
ANNEX BB, CHANGES IN THE SECOND EDITION
TRF No. IECEN60950_1C
Result - Remark
Verdict

Page 32 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
EN 60950-1:2006 – CENELEC COMMON MODIFICATIONS
Contents
Add the following annexes:
Annex ZA (normative)
Normative references to international publications with
their corresponding European publications
Annex ZB (normative)
Special national conditions
Annex ZC (informative) A-deviations
P
General
Delete all the “country” notes in the reference document according to the following
list:
1.4.8
Note 2
1.5.1
Note 2 & 3
1.5.7.1
Note
1.5.8
Note 2
1.5.9.4
Note
1.7.2.1
Note 4, 5 & 6
2.2.3
Note
2.2.4
Note
2.3.2
Note
2.3.2.1 Note 2
2.3.4
Note 2
2.6.3.3
Note 2 & 3
2.7.1
Note
2.10.3.2 Note 2
2.10.5.13 Note 3
3.2.1.1 Note
3.2.4
Note 3.
2.5.1
Note 2
4.3.6
Note 1 & 2
4.7
Note 4
4.7.2.2
Note
4.7.3.1 Note 2
5.1.7.1
Note 3 & 4
5.3.7
Note 1
6
Note 2 & 5
6.1.2.1
Note 2
6.1.2.2
Note
6.2.2
Note 6.
2.2.1
Note 2
6.2.2.2
Note
7.1
Note 3
7.2
Note
7.3
Note 1 & 2
G.2.1
Note 2
Annex H Note 2
P
1.3.Z1
Add the following subclause:
1.3.Z1 Exposure to excessive sound pressure
The apparatus shall be so designed and constructed as to present no danger when
used for its intended purpose, either in normal operating conditions or under fault
conditions, particularly providing protection against exposure to excessive sound
pressures from headphones or earphones.
P
NOTE Z1 A new method of measurement is described in EN 50332-1, Sound system
equipment:
Headphones and earphones associated with portable audio equipment - Maximum sound
pressure level measurement methodology and limit considerations - Part 1: General method
for “one package equipment”, and in EN 50332-2, Sound system equipment: Headphones
and earphones associated with portable audio equipment - Maximum sound pressure level
measurement methodology and limit considerations - Part 2: Guidelines to associate sets
with headphones coming from different manufacturers.
1.5.1
Add the following NOTE:
N/A
NOTE Z1 The use of certain substances in electrical and electronic equipment is restricted
within the EU: see Directive 2002/95/EC
1.7.2.1
Add the following NOTE:
NOTE Z1 In addition, the instructions shall include, as far as applicable, a warning that
excessive sound pressure from earphones and headphones can cause hearing loss
TRF No. IECEN60950_1C
N/A
Page 33 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
2.7.1
Replace the subclause as follows:
Basic requirements
To protect against excessive current, short-circuits and earth faults in PRIMARY
CIRCUITS, protective devices shall be included either as integral parts of the
equipment or as parts of the building installation, subject to the following, a), b) and
c):
a) except as detailed in b) and c), protective devices necessary to comply with the
requirements of 5.3 shall be included as parts of the equipment;
b) for components in series with the mains input to the equipment such as the
supply cord, appliance coupler, r.f.i. filter and switch, short-circuit and earth fault
protection may be provided by protective devices in the building installation;
c) it is permitted for PLUGGABLE EQUIPMENT TYPE B or PERMANENTLY
CONNECTED EQUIPMENT, to rely on dedicated overcurrent and short-circuit
protection in the building installation, provided that the means of protection, e.g.
fuses or circuit breakers, is fully specified in the installation instructions.
If reliance is placed on protection in the building installation, the installation
instructions shall so state, except that for PLUGGABLE EQUIPMENT TYPE A the
building installation shall be regarded as providing protection in accordance with the
rating of the wall socket outlet.
N/A
2.7.2
This subclause has been declared ‘void’.
N/A
3.2.3
Delete the NOTE in Table 3A, and delete also in this table the conduit sizes in
parentheses.
N/A
3.2.5.1
Replace
“60245 IEC 53” by “H05 RR-F”;
“60227 IEC 52” by “H03 VV-F or H03 VVH2-F”;
“60227 IEC 53” by “H05 VV-F or H05 VVH2-F2”.
In Table 3B, replace the first four lines by the following:
a)
| Up to and including 6
|
0,75
|
b)
| Over 6 up to and including 10
|
(0,75)
1,0
|
c)
1,5
|
| Over 10 up to and including 16
|
(1,0)
In the conditions applicable to Table 3B delete the words “in some countries” in
a)
condition .
In NOTE 1, applicable to Table 3B, delete the second sentence.
N/A
3.3.4
In Table 3D, delete the fourth line: conductor sizes for 10 to 13 A, and replace with
the following:
| Over 10 up to and including 16 |
1,5 to 2,5
|
1,5 to 4
|
Delete the fifth line: conductor sizes for 13 to 16 A.
N/A
Add the following NOTE:
N/A
4.3.13.6
Result - Remark
NOTE Z1 Attention is drawn to 1999/519/EC: Council Recommendation on the limitation of
exposure of the general public to electromagnetic fields 0 Hz to 300 GHz. Standards taking
into account this Recommendation which demonstrate compliance with the applicable EU
Directive are indicated in the OJEC.
TRF No. IECEN60950_1C
Verdict
Page 34 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Annex H
Replace the last paragraph of this annex by:
At any point 10 cm from the surface of the OPERATOR ACCESS AREA, the dose
rate shall not exceed 1 µSv/h (0,1 mR/h) (see NOTE). Account is taken of the
background level.
Replace the notes as follows:
Verdict
N/A
NOTE These values appear in Directive 96/29/Euratom.
Delete NOTE 2.
Bibliography
Additional EN standards.

ZA
NORMATIVE REFERENCES TO INTERNATIONAL PUBLICATIONS WITH THEIR
CORRESPONDING EUROPEAN PUBLICATIONS

ZB
SPECIAL NATIONAL CONDITIONS
P
1.2.4.1
In Denmark, certain types of Class I appliances (see 3.2.1.1) may be provided with
a plug not establishing earthing conditions when inserted into Danish socket-outlets.
N/A
1.5.7.1
In Finland, Norway and Sweden, resistors bridging BASIC INSULATION in
CLASS I PLUGGABLE EQUIPMENT TYPE A must comply with the requirements in
1.5.7.2.
N/A
1.5.8
In Norway, due to the IT power system used (see annex V, Figure V.7), capacitors
are required to be rated for the applicable line-to-line voltage (230 V).
N/A
1.5.9.4
In Finland, Norway and Sweden, the third dashed sentence is applicable only to
equipment as defined in 6.1.2.2 of this annex.
N/A
1.7.2.1
In Finland, Norway and Sweden, CLASS I PLUGGABLE EQUIPMENT TYPE A
intended for connection to other equipment or a network shall, if safety relies on
connection to protective earth or if surge suppressors are connected between the
network terminals and accessible parts, have a marking stating that the equipment
must be connected to an earthed mains socket-outlet.
The marking text in the applicable countries shall be as follows:
In Finland: "Laite on liitettävä suojamaadoituskoskettimilla varustettuun
pistorasiaan"
In Norway: “Apparatet må tilkoples jordet stikkontakt”
In Sweden: “Apparaten skall anslutas till jordat uttag”
N/A
1.7.5
In Denmark, socket-outlets for providing power to other equipment shall be in
accordance with the Heavy Current Regulations, Section 107-2-D1, Standard Sheet
DK 1-3a, DK 1-5a or DK 1-7a, when used on Class I equipment. For STATIONARY
EQUIPMENT the socket-outlet shall be in accordance with Standard Sheet DK 1-1b
or DK 1-5a.
N/A
2.2.4
In Norway, for requirements see 1.7.2.1, 6.1.2.1 and 6.1.2.2 of this annex.
N/A
2.3.2
In Finland, Norway and Sweden there are additional requirements for the
insulation. See 6.1.2.1 and 6.1.2.2 of this annex.
N/A
2.3.4
In Norway, for requirements see 1.7.2.1, 6.1.2.1 and 6.1.2.2 of this annex.
N/A
TRF No. IECEN60950_1C
Page 35 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
2.6.3.3
In the United Kingdom, the current rating of the circuit shall be taken as 13 A, not
16 A.
N/A
2.7.1
In the United Kingdom, to protect against excessive currents and short-circuits in
the PRIMARY CIRCUIT of DIRECT PLUG-IN EQUIPMENT, tests according to 5.3
shall be conducted, using an external protective device rated 30 A or 32 A. If these
tests fail, suitable protective devices shall be included as integral parts of the
DIRECT PLUG-IN EQUIPMENT, so that the requirements of 5.3 are met.
N/A
2.10.5.13
In Finland, Norway and Sweden, there are additional requirements for the
insulation, see 6.1.2.1 and 6.1.2.2 of this annex.
N/A
3.2.1.1
In Switzerland, supply cords of equipment having a RATED CURRENT not
exceeding 10 A shall be provided with a plug complying with SEV 1011 or IEC
60884-1 and one of the following dimension sheets:
SEV 6532-2.1991
Plug Type 15 3P+N+PE
250/400 V, 10 A
SEV 6533-2.1991
Plug Type 11 L+N
250 V, 10 A
SEV 6534-2.1991
Plug Type 12 L+N+PE
250 V, 10 A
In general, EN 60309 applies for plugs for currents exceeding 10 A. However, a 16
A plug and socket-outlet system is being introduced in Switzerland, the plugs of
which are according to the following dimension sheets, published in February 1998:
SEV 5932-2.1998
Plug Type 25 3L+N+PE
230/400 V, 16 A
SEV 5933-2.1998
Plug Type 21 L+N
250 V, 16 A
SEV 5934-2.1998
Plug Type 23 L+N+PE
250 V, 16 A
N/A
3.2.1.1
In Denmark, supply cords of single-phase equipment having a rated current not
exceeding13 A shall be provided with a plug according to the Heavy Current
Regulations, Section 107-2-D1.
CLASS I EQUIPMENT provided with socket-outlets with earth contacts or which are
intended to be used in locations where protection against indirect contact is
required according to the wiring rules shall be provided with a plug in accordance
with standard sheet DK 2-1a or DK 2-5a.
If poly-phase equipment and single-phase equipment having a RATED CURRENT
exceeding 13 A is provided with a supply cord with a plug, this plug shall be in
accordance with the Heavy Current Regulations, Section 107-2-D1 or EN 60309-2.
N/A
3.2.1.1
In Spain, supply cords of single-phase equipment having a rated current not
exceeding 10 A shall be provided with a plug according to UNE 20315:1994.
Supply cords of single-phase equipment having a rated current not exceeding 2,5 A
shall be provided with a plug according to UNE-EN 50075:1993.
CLASS I EQUIPMENT provided with socket-outlets with earth contacts or which are
intended to be used in locations where protection against indirect contact is
required according to the wiring rules, shall be provided with a plug in accordance
with standard UNE 20315:1994.
If poly-phase equipment is provided with a supply cord with a plug, this plug shall be
in accordance with UNE-EN 60309-2.
N/A
TRF No. IECEN60950_1C
Result - Remark
Verdict
Page 36 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
3.2.1.1
In the United Kingdom, apparatus which is fitted with a flexible cable or cord and is
designed to be connected to a mains socket conforming to BS 1363 by means of
that flexible cable or cord and plug, shall be fitted with a ‘standard plug’ in
accordance with Statutory Instrument 1768:1994 - The Plugs and Sockets etc.
(Safety) Regulations 1994, unless exempted by those regulations.
Verdict
N/A
NOTE ‘Standard plug’ is defined in SI 1768:1994 and essentially means an approved plug
conforming to BS 1363 or an approved conversion plug.
3.2.1.1
In Ireland, apparatus which is fitted with a flexible cable or cord and is designed to
be connected to a mains socket conforming to I.S. 411 by means of that flexible
cable or cord and plug, shall be fitted with a 13 A plug in accordance with Statutory
Instrument 525:1997 - National Standards Authority of Ireland (section 28) (13 A
Plugs and Conversion Adaptors for Domestic Use) Regulations 1997.
N/A
3.2.4
In Switzerland, for requirements see 3.2.1.1 of this annex.
N/A
3.2.5.1
In the United Kingdom, a power supply cord with conductor of 1,25 mm2 is
allowed for equipment with a rated current over 10 A and up to and including 13 A.
N/A
3.3.4
In the United Kingdom, the range of conductor sizes of flexible cords to be
accepted by terminals for equipment with a RATED CURRENT of over 10 A up to
and including 13 A is:
2
2
• 1,25 mm to 1,5 mm nominal cross-sectional area.
N/A
4.3.6
In the United Kingdom, the torque test is performed using a socket outlet
complying with BS 1363 part 1:1995, including Amendment 1:1997 and Amendment
2:2003 and the plug part of DIRECT PLUG-IN EQUIPMENT shall be assessed to
BS 1363: Part 1, 12.1, 12.2, 12.3, 12.9, 12.11, 12.12, 12.13, 12.16 and 12.17,
except that the test of 12.17 is performed at not less than 125 °C. Where the metal
earth pin is replaced by an Insulated Shutter Opening Device (ISOD), the
requirements of clauses 22.2 and 23 also apply.
N/A
4.3.6
In Ireland, DIRECT PLUG-IN EQUIPMENT is known as plug similar devices. Such
devices shall comply with Statutory Instrument 526:1997 - National Standards
Authority of Ireland (Section 28) (Electrical plugs, plug similar devices and sockets
for domestic use) Regulations, 1997.
N/A
5.1.7.1
In Finland, Norway and Sweden TOUCH CURRENT measurement results
exceeding 3,5 mA r.m.s. are permitted only for the following equipment:
• STATIONARY PLUGGABLE EQUIPMENT TYPE A that
is intended to be used in a RESTRICTED ACCESS LOCATION where
equipotential bonding has been applied, for example, in a
telecommunication centre; and
has provision for a permanently connected PROTECTIVE EARTHING
CONDUCTOR; and
is provided with instructions for the installation of that conductor by a
SERVICE PERSON;
• STATIONARY PLUGGABLE EQUIPMENT TYPE B;
• STATIONARY PERMANENTLY CONNECTED EQUIPMENT.
N/A
TRF No. IECEN60950_1C
Page 37 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
6.1.2.1
In Finland, Norway and Sweden, add the following text between the first and
second paragraph of the compliance clause:
If this insulation is solid, including insulation forming part of a component, it shall at
least consist of either
two layers of thin sheet material, each of which shall pass the electric
strength test below, or
one layer having a distance through insulation of at least 0,4 mm, which
shall pass the electric strength test below.
If this insulation forms part of a semiconductor component (e.g. an optocoupler),
there is no distance through insulation requirement for the insulation consisting of
an insulating compound completely filling the casing, so that CLEARANCES and
CREEPAGE DISTANCES do not exist, if the component passes the electric
strength test in accordance with the compliance clause below and in addition
passes the tests and inspection criteria of 2.10.11 with an electric strength
test of 1,5 kV multiplied by 1,6 (the electric strength test of 2.10.10 shall be
performed using 1,5 kV), and
is subject to ROUTINE TESTING for electric strength during manufacturing,
using a test voltage of 1,5 kV.
It is permitted to bridge this insulation with a capacitor complying with
EN 132400:1994, subclass Y2.
A capacitor classified Y3 according to EN 132400:1994, may bridge this insulation
under the following conditions:
the insulation requirements are satisfied by having a capacitor classified Y3
as defined by EN 132400, which in addition to the Y3 testing, is tested with
an impulse test of 2,5 kV defined in EN 60950-1:2006, 6.2.2.1;
the additional testing shall be performed on all the test specimens as
described in EN 132400;
the impulse test of 2,5 kV is to be performed before the endurance test in
EN 132400, in the sequence of tests as described in EN 132400.
N/A
6.1.2.2
In Finland, Norway and Sweden, the exclusions are applicable for
PERMANENTLY CONNECTED EQUIPMENT, PLUGGABLE EQUIPMENT TYPE B
and equipment intended to be used in a RESTRICTED ACCESS LOCATION where
equipotential bonding has been applied, e.g. in a telecommunication centre, and
which has provision for a permanently connected PROTECTIVE EARTHING
CONDUCTOR and is provided with instructions for the installation of that conductor
by a SERVICE PERSON.
N/A
7.2
In Finland, Norway and Sweden, for requirements see 6.1.2.1 and 6.1.2.2 of this
annex.
The term TELECOMMUNICATION NETWORK in 6.1.2 being replaced by the term
CABLE DISTRIBUTION SYSTEM.
N/A
7.3
In Norway and Sweden, there are many buildings where the screen of the coaxial
cable is normally not connected to the earth in the building installation.
N/A
7.3
In Norway, for installation conditions see EN 60728-11:2005.
N/A
ZC
A-DEVIATIONS (informative)
TRF No. IECEN60950_1C
Result - Remark
Verdict
P
Page 38 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
1.5.1
Sweden (Ordinance 1990:944)
Add the following:
Result - Remark
Verdict
N/A
NOTE In Sweden, switches containing mercury are not permitted.
1.5.1
Switzerland (Ordinance on environmentally hazardous substances SR 814.081,
Annex 1.7, Mercury - Annex 1.7 of SR 814.81 applies for mercury.)
Add the following:
N/A
NOTE In Switzerland, switches containing mercury such as thermostats, relays and level
controllers are not allowed.
1.7.2.1
Denmark (Heavy Current Regulations)
Supply cords of CLASS I EQUIPMENT, which is delivered without a plug, must be
provided with a visible tag with the following text:
Vigtigt!
Lederen med grøn/gul isolation
må kun tilsluttes en klemme mærket
N/A
eller
If essential for the safety of the equipment, the tag must in addition be provided with
a diagram, which shows the connection of the other conductors, or be provided with
the following text:
“For tilslutning af de øvrige ledere, se medfølgende installationsvejledning.”
1.7.2.1
Germany (Gesetz über technische Arbeitsmittel und Verbraucherprodukte (Geräteund Produktsicherheitsgesetz – GPSG) [Law on technical labour equipment and
consumer products], of 6th January 2004, Section 2, Article 4, Clause (4), Item 2).
If for the assurance of safety and health certain rules during use, amending or
maintenance of a technical labour equipment or readymade consumer product are
to be followed, a manual in German language has to be delivered when placing the
product on the market.
Of this requirement, rules for use even only by SERVICE PERSONS are not
exempted.
N/A
1.7.5
Denmark (Heavy Current Regulations)
With the exception of CLASS II EQUIPMENT provided with a socket outlet in
accordance with the Heavy Current Regulations, Section 107-2-D1, Standard Sheet
DK 1-4a, CLASS II EQUIPMENT shall not be fitted with socket-outlets for providing
power to other equipment.
N/A
1.7.13
Switzerland (Ordinance on chemical hazardous risk reduction SR 814.81, Annex
2.15 Batteries)
Annex 2.15 of SR 814.81 applies for batteries.
N/A
5.1.7.1
Denmark (Heavy Current Regulations, Chapter 707, clause 707.4)
TOUCH CURRENT measurement results exceeding 3,5 mA r.m.s. are permitted
only for PERMANENTLY CONNECTED EQUIPMENT and PLUGGABLE
EQUIPMENT TYPE B.
N/A
TRF No. IECEN60950_1C
Page 39 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
1.5.1
TABLE: List of critical components
Verdict
P
Object/part no.
Manufacturer/
trademark
Type/model
Technical data
Standard
Mark(s) of
1.
conformity
PCB
--
--
V-1 or better
min. 105°C
UL 94
UL
Enclosure
CHI MEI
PA-757(+)
CORPORATION
HB or better,
min. 1.9mm
thick, 80°C
UL 94
UL
PA-765A (+)
CHI MEI
CORPORATION
V-1 or better,
min. 1.9 mm
thick. 80°C
UL 94
UL
Metal chassis
--
--
Min. 0.8mm
thick
--
--
Metal mesh
--
--
Min. 0.5 mm
thick
--
--
VGA Fan
AVC
BATA0716R2H- 12Vdc, 0.3A,
001
10.95CFM
EN 60950-1:
2001,
UL 507
TÜV, UL
CPU Fan
AVC
BATA0822R2H- 12Vdc, 0.52A,
001
21.73CFM
EN 60950-1:
2001,
UL 507
TÜV, UL
System Fan
AVC
C3010S12H505K
12Vdc, 0.10A,
3.31CFM
EN 60950-1:
2001,
UL 507
TÜV, UL
LCD Panel
CHI MEI (CMO)
M236H1-L01
TFT type, 23.6”
--
--
ADAPTOR
Delta Electronics ADP-180HB B
Inc.
FSP
I/P: 100-240V~, IEC/EN 60950-1: TÜV, UL, CB
(issued by
50-60Hz, 2.25A 2001,
TÜV/RH Ref.
UL
60950-1
O/P: +19V/ 9.5A
Certif. No.
40°C, Class I
JPTUV-018297)
FSP180-ABAN1 I/P: 100-240V~,
50-60Hz, 2.5A
O/P: +19V/
9.47A
40°C, Class I.
RTC Battery
(Lithium)
FDK ENERGY
CO LTD
TRF No. IECEN60950_1C
CR2032
3V, 220mAh,
maximum
abnormal
charge current=
5mA.
IEC/EN 60950-1: TÜV, UL, CB
(issued by
2001,
TÜV/RH Ref.
UL 60950-1
Certif. No.
JPTUV-021834)
UL 1642
UL
Page 40 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
Matsushita
Electric
Industrial Co.
Ltd. (Panasonic
Corp Of North
America)
CR2032
3V, 220mAh,
maximum
abnormal
charge current=
10mA.
UL 1642
UL
Vic-Dawn
Enterprise Co.
Ltd.(KTS)
CR2032
3V, 220mAh,
maximum
abnormal
charge current=
10mA.
UL 1642
UL
HDD Drive
(Optional)
Seagate or
equivalent
ST3 series or
3.5 series or
equivalent
+5/+12Vdc,
max. 1.5A
IEC/EN 609501: 2001,
UL 60950-1
TÜV, UL, CB
(issued by UL
Ref. Certif. No.
US/10879/UL)
Speaker (Two
Provided)
--
--
8Ω, 5W
--
--
Speaker (One
Provided)
--
--
6.4Ω, 10W
--
--
DVD Multi Drive
(Optional)
Hitachi-LG Data GCC-T2** (* =
Storage, Inc. or any
alphanumeric
equivalent
character) or
equivalent
5Vdc, 1.8A,
Laser Class 1
IEC/EN 609501: 2001,
IEC 60825-1:
1993+A1+A2,
UL 60950-1
TÜV, UL, CB
(issued by ETL
Ref. Certif. No.
SE-50804)
Hitachi-LG Data GSA-T5** (first 5Vdc, 1.5A,
Storage, Inc. or “*”= any number Laser Class 1
0-9; second “*”=
equivalent
any
alphanumeric
character) or
equivalent
IEC/EN 609501: 2001,
IEC 60825-1:
1993+A1+A2,
UL 60950-1
TÜV, UL, CB
(issued by ETL
Ref. Certif. No.
SE-53474)
Hitachi-LG Data GT10* (* = any
Storage, Inc. or alphanumeric
character) or
equivalent
equivalent
5Vdc, 1.8A,
Laser Class 1
IEC/EN 609501: 2001,
IEC 60825-1:
1993+A1+A2,
UL 60950-1
TÜV, UL, CB
(issued by ETL
Ref. Certif. No.
SE-54328)
Hitachi-LG Data GT3** ( *= any
Storage, Inc. or alphanumeric
character) or
equivalent
equivalent
5Vdc, 1.8A,
Laser Class 1
IEC/EN 609501: 2001, IEC
60825-1:
1993+A1+A2,
UL 60950-1
TÜV, UL, CB
(issued by ETL
Ref. Certif. No.
JSE-57485)
5Vdc, 1.5A,
DS-xx2Lxxx,
DS-xx2Sxxx (x = Laser Class 1
any
alphanumeric or
blank) or
equivalent
IEC/EN 609501: 2001,
IEC 60825-1:
1993+A1+A2,
UL 60950-1
TÜV, UL, CB
(issued by TÜV/
RH Ref. Certif.
No. JPTUV019661)
Philips & Lite-On
Digital Solutions
Corporation or
equivalent
TRF No. IECEN60950_1C
Page 41 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
Philips & Lite-On
Digital Solutions
Corporation or
equivalent
5Vdc, 1.5A,
DS-xx3Lxxx,
DS-xx3Sxxx (x = Laser Class 1
any
alphanumeric or
blank) or
equivalent
IEC/EN 609501: 2001,
IEC 60825-1:
1993+A1+A2,
UL 60950-1
TÜV, UL, CB
(issued by TÜV/
RH Ref. Certif.
No. JPTUV024410)
Philips & Lite-On
Digital Solutions
Corporation or
equivalent
5Vdc, 1.5A,
DS-xx4Lxxx,
DS-xx4Sxxx (x = Laser Class 1
any
alphanumeric or
blank) or
equivalent
IEC/EN 609501: 2001,
IEC 60825-1:
1993+A1+A2,
UL 60950-1
TÜV, UL, CB
(issued by TÜV/
RH Ref. Certif.
No. JPTUV027914)
SONY NEC
optiarc Inc or
equivalent
AD-X58XSXXX 5Vdc, 1.5A,
Laser Class 1
(X= 0-9, A-Z,
blank or hyphen)
or equivalent
IEC/EN 609501: 2001,
IEC 60825-1:
1993+A1+A2,
UL 60950-1
TÜV, UL, CB
(issued by TÜV/
RH Ref. Certif.
No. JPTUV022707)
SONY NEC
optiarc Inc or
equivalent
AX-X56XS-XX
(X = 0-9, A-Z or
blank) or
equivalent
5Vdc, 1.5A,
Laser Class 1
EN 60950-1:
2001,
EN 60825-1:
1993+A1+A2,
UL 60950-1
TÜV, UL
Toshiba
Samsung
Storage
Technology
Korea
Corporation or
equivalent
TS-L632, SNS082, TS-L633,
SN-S083 or
equivalent
5Vdc, 1.5A or
1.3A, Laser
Class 1
IEC/EN 609501: 2001,
IEC 60825-1:
1993+A1+A2,
UL 60950-1
TÜV, UL, CB
(issued by
Nemko Ref.
Certif. No.
NO42511)
Toshiba
Samsung
Storage
Technology
Korea
Corporation or
equivalent
TS-T633, SNT083 or
equivalent
5Vdc, 1.3A,
Laser Class 1
IEC/EN 609501: 2001,
IEC 60825-1:
1993+A1+A2,
UL 60950-1
TÜV, UL, CB
(issued by
Nemko Ref.
Certif. No.
NO45550)
Toshiba
Samsung
Storage
Technology
Korea
Corporation or
equivalent
TS-U633*; SU- 5Vdc, 1.3A,
Laser Class 1
S083 (* = any
alphanumeric or
blank) or
equivalent
IEC 60950-1:
2005,
EN 60950-1:
2006,
IEC 60825-1:
2007,
UL 60950-1
TÜV, UL, CB
(issued by
Nemko Ref.
Certif. No.
NO49136)
TRF No. IECEN60950_1C
Page 42 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
Hitachi-LG Data GU1**, GSAStorage, Inc. or U20N-Z (*= any
alphanumeric or
equivalent
blank) or
equivalent
5Vdc, 1.5A,
Laser Class 1
IEC 60950-1:
2005,
EN 60950-1:
2006,
IEC 60825-1:
1993+A1+A2,
UL 60950-1
TÜV, UL, CB
(issued by ETL
Ref. Certif. No.
SE-56621)
UJ892
Panasonic
Communications
Co., Ltd.
5Vdc, 1.6A,
Laser Class 1
IEC/EN 60950-1:
2001,
IEC 60825-1:
1993+A1+A2,
UL 60950-1
TÜV, UL, CB
(issued by
TÜV/RH Ref.
Certif. No.
JPTUV-025231)
5Vdc,1.5A,
Laser Class 1
IEC/EN 609501: 2001,
IEC 60825-1:
1993+A1+A2,
UL 60950-1
TÜV, UL, CB
(issued by ETL
Ref. Certif. No.
SE-54876)
BC-5500Sxxx (x 5Vdc,2.0A,
= blank, “-“, A-Z Laser Class 1
or 0-9) or
equivalent
IEC/EN 609501: 2001,
IEC 60825-1:
1993+A1+A2,
UL 60950-1
TÜV, UL, CB
(issued by TÜV/
RH Ref. Certif.
No. JPTUV018596)
BLUE RAY Disc Hitachi-LG Data CT1** (* = any
Drive (ODD)
Storage, Inc. or alphanumeric
character) or
equivalent
equivalent
SONY NEC
optiarc Inc or
equivalent
Hitachi-LG Data CT2** (* = any
Storage, Inc. or alphanumeric
character) or
equivalent
equivalent
5Vdc,1.5A,
Laser Class 1
IEC 60950-1:
2005,
EN 60950-1:
2006,
IEC 60825-1:
1993+A1+A2,
UL 60950-1
TÜV, UL, CB
(issued by ETL
Ref. Certif. No.
SE-56244)
DC/AC Inverter
FSP
INV22-4007
Input: 12Vdc,
max. 2.8A
Output: 2100V,
max. 7.8mA
--
--
- Transformer
(T1, T2)
FSP
FSP083-3L01
130°C
--
--
- Fuse (F1)
WICKMANN
392
3.15A, 250V
EN 60127-3
UL, VDE
- PCB
--
--
V-1 or better
min. 105°C
UL 94
UL
TV-tuner
(optional)
AVerMedia
A336_AF
+3.3Vdc
--
--
AVerMedia
A320
+3.3Vdc
--
--
AVerMedia
A369
+3.3Vdc
--
--
AVerMedia
A336_AE
+3.3Vdc
--
--
TRF No. IECEN60950_1C
Page 43 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
BOURNS
PolySwitch
provide to VGA,
USB, Card
Reader,
Camera, HDMI,
Touch pad (FS1,
FS2, FS3, FS4,
FS8, FS12,
FS10, F1, FS5,
FS6)
Result - Remark
MFMSMF150/24X2
24Vdc, 1.5A
Verdict
EN 60730-1,
UL 1434
TÜV, UL
BOURNS
MF-MSMF260-2 6Vdc, 2.6A
EN 60730-1,
UL 1434
TÜV, UL
BOURNS
MF-USMF110-2 6Vdc, 1.1A
EN 60730-1,
UL 1434
TÜV, UL
LITTELFUSE
1206L050/15YR 15Vdc, 0.5A
EN 60730-1,
UL 1434
TÜV, UL
POLYTRONICS SMD1206P050T 15Vdc, 0.5A
F/15
EN 60730-1,
UL 1434
TÜV, UL
POLYTRONICS SMD1812P150T 24Vdc, 1.5A
F/24
EN 60730-1,
UL 1434
TÜV, UL
Tyco Electronics microSMD110F- 6Vdc, 1.1A
2
Corp.
(Raychem)
EN 60730-1,
UL 1434
TÜV, UL
Tyco Electronics miniSMDC110F 6Vdc or 8Vdc,
Corp.
1.1A
(Raychem)
EN 60730-1,
UL 1434
TÜV, UL
Tyco Electronics miniSMDC150F/ 24Vdc, 1.5A
24-2
Corp.
(Raychem)
EN 60730-1,
UL 1434
TÜV, UL
Supplementary information:
1. An asterisk indicates a mark that assures the agreed level of surveillance.
1.6.2
TABLE: Electrical data (in normal conditions)
P
U (Vdc)
I (A)
Irated (A)
P (W)
Fuse #
Ifuse (A)
19
6.9
9.5
131.1
--
--
Condition/status
Maximum normal load.
Supplementary information:
2.10.3 and TABLE: Clearance and creepage distance measurements
2.10.4
TRF No. IECEN60950_1C
N/A
Page 44 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Clearance (cl) and creepage
distance (cr) at/of/between:
Result - Remark
U peak
(V)
U r.m.s.
(V)
Required
cl (mm)
cl
(mm)
Verdict
Required
cr (mm)
cr
(mm)
Supplementary information:
2.10.5
TABLE: Distance through insulation measurements
Distance through insulation (DTI) at/of:
U peak
(V)
N/A
U r.m.s.
(V)
Test
voltage
(V)
Required
DTI
(mm)
DTI
(mm)
Supplementary information:
4.3.8
TABLE: Batteries
N/A
The tests of 4.3.8 are applicable only when appropriate battery
data is not available
N/A
Is it possible to install the battery in a reverse polarity position?
N/A
Non-rechargeable batteries
Discharging
Meas.
current
Manuf.
Specs.
Unintentional
charging
Rechargeable batteries
Charging
Meas.
current
Manuf.
Specs.
Discharging
Meas.
current
Manuf.
Specs.
Reversed charging
Meas.
current
Manuf.
Specs.
Max.
current
during
normal
condition
Max.
current
during
fault
condition
Test results:
Verdict
- Chemical leaks
N/A
- Explosion of the battery
N/A
- Emission of flame or expulsion of molten metal
N/A
- Electric strength tests of equipment after completion of tests
N/A
TRF No. IECEN60950_1C
Page 45 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
Supplementary information:
4.5
TABLE: Thermal requirements
P
Supply voltage (V) ........................... :
19Vdc

Ambient Tmin (°C) ............................. :
--

Ambient Tmax (°C) ............................ :
See below

T (°C)
Allowed
Tmax (°C)
1. PCB body near CPU
75.4
105
2. Heat sink body CPU
64.9
105
3. Heat sink body U95
63.4
105
4. Heat sink body U18
83.6
105
5. RTC battery body
61.5
--
6. DRAM body
82.8
105
7. HDD body
65.1
--
8. ODD body
55.3
--
9. Interanl metal enclosure near CPU
60.7
--
10. Outside of enclosure near CPU
50.5
95
11. Panel body
46.0
95
12. T2 coil (DC/AC Inverter)
73.3
130
13. U1 body (DC/AC Inverter)
67.7
105
14. Operating ambient
40.0
--
15. Actual ambient
21.5
--
Maximum measured temperature T of part/at::
Supplementary information:
Temperature T of winding:
t1 (°C)
R1 (Ω)
t2 (°C)
R2 (Ω)
T (°C)
Allowed Insulation
class
Tmax (°C)
Supplementary information:
• The temperatures were measured under worst normal mode defined in 1.2.2.1 and as described in subclause 1.6.2 and at voltages as described above.
• With a maximum ambient temperature of +40°C as declared by the manufacturer.
• All values for T (°C) are re-calculated from actual ambient.
4.5.5
TABLE: Ball pressure test of thermoplastic parts
Allowed impression diameter (mm) .................. : ≤ 2 mm
TRF No. IECEN60950_1C
N/A

Page 46 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Part
Result - Remark
Verdict
Test temperature
(°C)
Impression diameter
(mm)
Supplementary information:
4.7
Table: Resistance to fire
Part
P
Manufacturer of
material
Type of material
Thickness
(mm)
Flammability
class
Evidence
Chi Mei
PA-757(+)
1.9
HB
--
Mesh
--
metal
0.5
--
--
Internal enclosure
--
metal
0.8
--
--
PCB
--
--
--
V-1
--
External enclosure
Supplementary information:
5.2
TABLE: Electric strength tests, impulse tests and voltage surge tests
Test voltage applied between:
P
Voltage shape
(AC, DC,
impulse, surge)
Test voltage
(V)
Breakdown
Yes / No
Insulation
Resistance
Primary (External SPS) to SELV (Equipment)
DC
4242
No
Primary (External SPS) to enclosure with foil
(Equipment)
DC
4242
No
After voltage surge test and impulse test
Supplementary information:
5.3
TABLE: Fault condition tests
P
Ambient temperature (°C) ..................................... : See below

Power source for EUT: Manufacturer, model/type, See appended table 1.5.1.
output rating ........................................................... :

Component
No.
Fault
TRF No. IECEN60950_1C
Supply
voltage
(V)
Test
time
Fuse #
Fuse
current
(A)
Observation
Page 47 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
CPU Fan
Stalled
19Vdc
2 hr
--
6.9
Unit operating normally. No
hazardous.
CPU= 81.7°C,
U95= 49.6°C,
U18= 80.1°C,
Ambient= 21.7°C
VGA Fan
Stalled
19Vdc
2 hr
--
6.9
Unit operating normally. No
hazardous.
CPU= 58.3°C,
U95= 57.5°C,
U18= 66.2°C,
Ambient= 22.3°C
System Fan
Stalled
19Vdc
1.5 hr
--
1.0
System shutdown after 10 min.
No hazardous.
CPU= 60.9°C,
U95= 48.8°C,
U18= 67.7°C,
Ambient= 22.5°C
Ventilation
Blocked
19Vdc
3.5 hr
--
6.9
Unit operating normally. No
hazardous.
CPU= 77.1°C,
U95= 72.8°C,
U18= 75.7°C,
Ambient= 21.7°C
VGA Port
(JVGA1) pin
1, 2, 3, 4, 5,
6, 7, 8, 10,
11, 13, 14,
15 – Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 0V. No
hazardous.
VGA Port
(JVGA1) pin
12 – Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 4.9V,
available current= 1mA. No
hazardous.
RJ-45 Port
(LAN1) pin 1,
2, 3, 4, 5, 6,
7, 8 – Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 0V. No
hazardous.
USB Port
(USB1) pin 2,
3, 4 – Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 0V. No
hazardous.
USB Port
(USB2) pin 2,
3, 4 – Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 0V. No
hazardous.
USB Port
(USB3) pin 2,
3, 4 – Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 0V. No
hazardous.
TRF No. IECEN60950_1C
Page 48 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
USB Port
(USB4) pin 2,
3, 4 – Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 0V. No
hazardous.
USB Port
(JUSB1) pin
2, 3, 4 –
Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 0V. No
hazardous.
USB Port
(JUSB2) pin
2, 3, 4 –
Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 0V. No
hazardous.
ESATA Port
(ESATA1) pin
1, 2, 3, 4, 5,
6, 7 – Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 0V. No
hazardous.
HDMI Port
(HDMI_IN1)
pin 1, 2, 3, 4,
5, 6, 7, 8, 9,
10, 12, 14,
15, 16, 17,
18, 19 –
Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 0V. No
hazardous.
HDMI Port
(HDMI_IN1)
pin 11 –
Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 3.16V,
available current= 1mA. No
hazardous.
HDMI Port
(HDMI_IN1)
pin 13 –
Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 2.8V,
available current= 1mA. No
hazardous.
Webcam
(JCAMERA1)
Pan 2, 3, 4 –
Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 0V. No
hazardous.
Touch Panel
(JTOUCH1)
pin 2, 4, 5, 6,
8 – Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 0V. No
hazardous.
Touch Panel
(JTOUCH1)
pin 3 – Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 3.0V,
available current= 1mA. No
hazardous.
Touch Pad
(JFP1) pin 1 –
Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 4.9V,
available current= 7mA. No
hazardous.
TRF No. IECEN60950_1C
Page 49 of 68
Report No. 11019890 001
IEC/EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
Touch Pad
(JFP1) pin 3 –
Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 2.5V,
available current= 1mA. No
hazardous.
Touch Pad
(JFP1) pin 6 –
Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 3.2V,
available current= 1mA. No
hazardous.
Touch Pad
(JFP1) pin 8 –
Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 0V. No
hazardous.
Touch Pad
(JFP2) pin 1,
3, 5, 7 –
Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 0V. No
hazardous.
Touch Pad
(JFP2) pin 2 –
Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 3.2V,
available current= 1mA. No
hazardous.
Touch Pad
(JFP2) pin 6 –
Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 2.8V,
available current= 1mA. No
hazardous.
B-CAS Card
Reader Slot
(JBCAS1) pin
1, 2, 3, 4, 5,
6, 7, 8 –
Return
o-l
19Vdc
1 sec.
--
--
Open circuit voltage= 0V. No
hazardous.
Supplementary information:
In fault column, where s-c = short-circuited, o-l = overload.
TRF No. IECEN60950_1C
ATTACHMENT
Measurement Section
Page 50 of 68
Clause
Requirement + Test
2.1.1.5
TABLE: Energy hazard measurement
Voltage (rated)
(V)
Report No.:
11019890 001
Result - Remark
Current (rated)
(A)
Verdict
N/A
Voltage (max.)
(V)
Current (max.)
(A)
VA (max.)
(VA)
Supplementary information:
2.1.1.7
Condition
TABLE: Discharge test
N/A
τ calculated τ measured
(s)
(s)
t u→ 0V
(s)
Comments
Supplementary information:
2.2.2
TABLE: SELV measurement (under normal conditions)
Transformer
Location
N/A
Voltage (max.) (V)
V peak
V d.c.
Voltage Limitation
Component
Supplementary information:
2.2.3
TABLE: SELV measurement (under fault conditions)
Location
Voltage (max.) (V)
N/A
Comments
Supplementary information:
2.4.2
Location
TABLE: Limited current circuit measurement
P
Voltage
(V)
Current
(mA)
Freq.
(kHz)
Limit
(mA)
Comments
CN2 (1 – 2)
35.2
17.6
47
32.9
Normal
CN2 (1 – 2)
36
18
47
32.9
C21A short
Rev. 0
ATTACHMENT
Measurement Section
Page 51 of 68
Clause
Requirement + Test
Report No.:
11019890 001
Result - Remark
Verdict
CN2 (1 – 2)
--
--
--
--
CN2 (1 – 2)
37.6
18.8
46
32.2
D12 open
CN2 (1 – 2)
31.4
15.7
47
32.9
U2 (5, 6 – 7, 8) short
CN2 (1 – 2)
18
9
47
32.9
T1 (1, 3 – 8) short
CN2 (1 – earth)
38
19
47
32.9
Normal
CN2 (1 – earth)
37.2
18.6
46
32.2
C21A short
CN2 (1 – earth)
--
--
--
--
C22 short, panel shutdown
CN2 (1 – earth)
--
--
--
--
D12 open, panel shutdown
CN2 (1 – earth)
32.8
16.4
47
32.9
U2 (5, 6 – 7, 8) short
CN2 (1 – earth)
14.2
7.1
47
32.9
T1 (1, 3 – 8) short
CN2 (2 – earth)
16.4
8.2
47
32.9
Normal
CN2 (2 – earth)
16
8
48
33.6
C21A short
CN2 (2 – earth)
--
--
--
--
C22 short, panel shutdown
CN2 (2 – earth)
--
--
--
--
D12 open, panel shutdown
CN2 (2 – earth)
5.2
2.6
48
33.6
CN2 (2 – earth)
--
--
--
--
T1 (1, 3 – 8) short, panel
shutdown
T1 (8 – 9)
--
--
--
--
Normal, panel shutdown
T1 (8 – 9)
--
--
--
--
C21A short, panel shutdown
T1 (8 – 9)
--
--
--
--
C22 short, panel shutdown
T1 (8 – 9)
--
--
--
--
D12 open, panel shutdown
T1 (8 – 9)
--
--
--
--
U2 (5, 6 – 7, 8) short, panel
shutdown
T1 (8 – 9)
--
--
--
--
T1 (1, 3 – 8) short, panel
shutdown
T1 (8 – earth)
38
19
47
32.9
Normal
T1 (8 – earth)
37.2
18.6
46
32.2
C21A short
T1 (8 – earth)
--
--
--
--
C22 short, panel shutdown
T1 (8 – earth)
--
--
--
--
D12 open, panel shutdown
T1 (8 – earth)
32.8
16.4
47
32.9
U2 (5, 6 – 7, 8) short
T1 (8 – earth)
14.2
7.1
47
32.9
T1 (1, 3 – 8) short
T1 (9 – earth)
38
19
47
32.9
Normal
T1 (9 – earth)
37.2
18.6
46
32.2
C21A short
T1 (9 – earth)
--
--
--
--
C22 short, panel shutdown
T1 (9 – earth)
--
--
--
--
D12 open, panel shutdown
Rev. 0
C22 short, panel shutdown
U2 (5, 6 – 7, 8) short
ATTACHMENT
Measurement Section
Page 52 of 68
Clause
Requirement + Test
Report No.:
11019890 001
Result - Remark
T1 (9 – earth)
32.8
16.4
47
32.9
U2 (5, 6 – 7, 8) short
T1 (9 – earth)
14.2
7.1
47
32.9
T1 (1, 3 – 8) short
CN2 (1 – 2)
1300
--
--
--
Open circuit
CN2 (1 – earth)
1300
--
--
--
Open circuit
CN2 (2 – earth)
36
--
--
--
Open circuit
T1 (8 – 9)
1340
--
--
--
Open circuit
T1 (8 – earth)
1300
--
--
--
Open circuit
T1 (9 – earth)
1300
--
--
--
Open circuit
Verdict
Supplementary information:
2.5
TABLE: Limited power source measurement
Limits
P
Measured
Verdict
8
4.4
P
100
11.0
P
8
4.4
P
100
11.0
P
8
4.5
P
100
13.5
P
8
4.5
P
100
13.5
P
8
3.5
P
100
9.5
P
8
3.5
P
100
9.5
P
8
2.7
P
100
9.4
P
According to Table 2B (normal condition) for USB1, Uoc= 4.98V
current (in A)
apparent power (in VA)
According to Table 2B (normal condition) for USB2, Uoc= 4.98V
current (in A)
apparent power (in VA)
According to Table 2B (normal condition) for USB3, Uoc= 4.99V
current (in A)
apparent power (in VA)
According to Table 2B (normal condition) for USB4, Uoc= 4.99V
current (in A)
apparent power (in VA)
According to Table 2B (normal condition) for JUSB1, Uoc= 4.98V
current (in A)
apparent power (in VA)
According to Table 2B (normal condition) for JUSB2, Uoc= 4.98V
current (in A)
apparent power (in VA)
According to Table 2B (normal condition) for JVGA1 (Pin 9), Uoc= 4.96V
current (in A)
apparent power (in VA)
Rev. 0
ATTACHMENT
Measurement Section
Page 53 of 68
Clause
Requirement + Test
Report No.:
Result - Remark
11019890 001
Verdict
According to Table 2B (normal condition) for (Webcam) JCAMERA1(Pin 1), Uoc= 3.2V
current (in A)
apparent power (in VA)
8
4.8
P
100
5.4
P
According to Table 2B (normal condition) for (Touch Panel) JTOUCH1 (Pin 1), Uoc= 4.93V
current (in A)
apparent power (in VA)
8
4.6
P
100
8.6
P
According to Table 2B (normal condition) for (Touch Pad ) JFP2 (Pin 4), Uoc= 5.01V
current (in A)
apparent power (in VA)
8
4.5
P
100
13.1
P
According to Table 2B (normal condition) for (Touch Pad ) JFP2 (Pin 8), Uoc= 3.2V
current (in A)
apparent power (in VA)
8
1.1
P
100
9
P
Supplementary information:
2.6.3.4
TABLE: Resistance of earthing measurement
Location
N/A
Resistance measured (mΩ) Comments
Supplementary information:
2.10.2
Table: Working voltage measurement
Location
RMS voltage (V)
N/A
Peak voltage (V) Comments
Supplementary information:
4.6.1, 4.6.2 Table: Enclosure opening measurements
Location
Top
Rev. 0
Size (mm)
2.2 x 31.8mm
P
Comments
- Numerous line shape openings which
covered an area 70 x 31.8mm.
- No component under those openings.
ATTACHMENT
Measurement Section
Page 54 of 68
Clause
Requirement + Test
Rear
Bottom
Other than above mentioned
Rev. 0
Report No.:
Result - Remark
11019890 001
Verdict
2.2 x 31.8mm
- Numerous line shape openings which
covered an area 97.4 x 31.8mm.
- Those openings were blocked by internal
heatsink.
- No hazardous voltage and energy
hazardous conductive parts were located
within 5° projection under those openings.
2.2 x 31.8mm
- Numerous line shape openings which
covered an area 66.0 x 31.8mm.
- Those openings were blocked by internal
heatsink.
- No hazardous voltage and energy
hazardous conductive parts were located
within 5° projection under those openings.
2.5 x 22.0mm
- Numerous line shape openings which
covered an area 86.6 x 22.0mm.
- No components were located within 5°
projection under those openings.
1.2 x 29.5mm
- Numerous line shape openings which
covered an area 86.6 x 22.0mm.
- Those openings were blocked by internal
mesh with diameter 1.5mm width hexagon
shape openings.
- Those openings were located near
memory stick.
2.0 x 30.0mm
- Numerous line shape openings which
covered an area 61.3 x 61.7mm.
- Those openings were blocked by internal
mesh with diameter 1.5mm width hexagon
shape openings.
- Those openings were located near DC
fan.
2.1 x 46.11mm
- Numerous line shape openings which
covered an area 46.11 x 44.2mm.
- Those openings were blocked by internal
mesh with diameter 1.5mm width hexagon
shape openings.
- Those openings were located near DC
fan.
1.2 x 36.1mm Max.
- Numerous line shape openings which
covered an area 462 x 36.1mm.
- The internal above the openings and
covers most of components, therefore
there’s no components were located
within 5° projection above those openings.
--
No opening.
ATTACHMENT
Measurement Section
Page 55 of 68
Clause
Requirement + Test
Report No.:
11019890 001
Result - Remark
Verdict
Supplementary information:
5.1.6
Condition
TABLE: Touch current and protective conductor current measurement
L→ terminal A
(mA)
N → terminal
A
(mA)
Limit
(mA)
N/A
Comments
Supplementary information:
C.2
TABLE: Insulation of transformers
Transformer part name ........................... :

Manufacturer........................................... :

Type ........................................................ :

Clearance (cl) and creepage
distance (cr) at/of/between:
Primary /input winding and
secondary/output winding
(internal)
Primary/input winding and core
(internal)
Secondary/output winding and
core (internal)
Primary/input part and
secondary/output part
(external)
Primary/input part and core
(external)
Primary/input part and
secondary/output winding
(external)
Secondary/output part and
core (external)
Secondary/output part and
primary/input winding
(external)
Description of design:
Rev. 0
N/A
U peak
(V)
U r.m.s.
(V)
Required
cl (mm)
cl
(mm)
Required
cr (mm)
cr
(mm)
ATTACHMENT
Measurement Section
Page 56 of 68
Clause
Requirement + Test
Result - Remark
(a) Bobbin
Primary/input pins
:
Secondary/output pins ............................................. :
Material (manufacturer, type, ratings) ...................... :
Thickness (mm)........................................................ :
(b) General
Supplementary information:
Rev. 0
Report No.:
11019890 001
Verdict
ATTACHMENT
National Differences
Page 57 of 68
Report No.:
11019890 001
National Differences
Clause
Result – Remark
Requirement − Test
Verdict
EUROPEAN GROUP DIFFERENCES AND NATIONAL DIFFERENCES
Differences according to................:
EN 60950-1:2006+A11:2009
CENELEC COMMON MODIFICATIONS (EN)
Normative references to international publications with their corresponding
European publications
P

ZB
ANNEX ZB, SPECIAL NATIONAL CONDITIONS (EN)
P
1.2.13.14
In Norway and Sweden, for requirements see
1.7.2.1 and 7.3 of this annex.
Replace the existing SNC by the following:
In Finland, Norway and Sweden, resistors
bridging BASIC INSULATION in CLASS I PLUGGABLE
EQUIPMENT TYPE A must comply with the
requirements in 1.5.7.1. In addition when a single
resistor is used, the resistor must withstand the
resistor test in 1.5.7.2.
Add as new SNC:
In Norway and Sweden, the screen of the cable
distribution system is normally not earthed at
the entrance of the building and there is normally
no equipotential bonding system within the
building. Therefore the protective earthing of the
building installation need to be isolated from
the screen of a cable distribution system.
It is however accepted to provide the insulation
external to the equipment by an adapter or an
interconnection cable with galvanic isolator, which
may be provided by e.g. a retailer.
The user manual shall then have the following or
similar information in Norwegian and
Swedish language respectively, depending on in
what country the equipment is intended to be
used in:
“Equipment connected to the protective earthing
of the building installation through the
mains connection or through other equipment
with a connection to protective earthing –
and to a cable distribution system using coaxial
cable, may in some circumstances
create a fire hazard. Connection to a cable
distribution system has therefore to be
provided through a device providing electrical
isolation below a certain frequency range
(galvanic isolator, see EN 60728-11).”
ZA
1.5.7.1
1.7.2.1
N/A
N/A
N/A
NOTE In Norway, due to regulation for installations of cable
distribution systems, and in Sweden, a galvanic isolator
shall provide electrical insulation below 5 MHz. The insulation
shall withstand a dielectric strength of 1,5 kV r.m.s.,
50 Hz or 60 Hz, for 1 min.
Translation to Norwegian (the Swedish text will
IECEE CB Bulletin on 2009-04-16
European Group Differences and National Differences
ATTACHMENT
National Differences
Page 58 of 68
Report No.:
11019890 001
National Differences
Clause
1.7.5
7.3
Result – Remark
Requirement − Test
also be accepted in Norway):
“Utstyr som er koplet til beskyttelsesjord via
nettplugg og/eller via annet jordtilkoplet
utstyr – og er tilkoplet et kabel-TV nett, kan
forårsake brannfare. For å unngå dette skal
det ved tilkopling av utstyret til kabel-TV nettet
installeres en galvanisk isolator mellom
utstyret og kabel- TV nettet.”
Translation to Swedish:
”Utrustning som är kopplad till skyddsjord via
jordat vägguttag och/eller via annan
utrustning och samtidigt är kopplad till kabel-TV
nät kan i vissa fall medfőra risk főr
brand. Főr att undvika detta skall vid anslutning
av utrustningen till kabel-TV nät
galvanisk isolator finnas mellan utrustningen och
kabel-TV nätet.”
Add the following paragraph to the existing SNC
for Denmark:
For CLASS II EQUIPMENT the socket outlet shall be
in accordance with Standard Sheet
DKA 1-4a.
Delete the existing SNC for Norway and Sweden
(based on NOTE 1 of IEC 60950-1:2005 +
corr. 1).
Add as new SNC (based on future NOTE 3 of
IEC 60950-1:200X):
In Norway and Sweden, for requirements see
1.2.13.14 and 1.7.2.1 of this annex.
ZC
ANNEX ZC, NATIONAL DEVIATIONS (EN)
1.5.1
Sweden
Delete the A-deviation.
Denmark
Delete the A-deviation.
Denmark
Delete the A-deviation.
Denmark
Delete the A-deviation.
1.7.2.1
1.7.5
5.1.7.1
IECEE CB Bulletin on 2009-04-16
Verdict
N/A
N/A
P
N/A
N/A
N/A
N/A
European Group Differences and National Differences
ATTACHMENT
National Differences
Page 59 of 68
Report No.:
11019890 001
National Differences
Clause
Result – Remark
Requirement − Test
Canadian National Differences
Verdict
P
SPECIAL NATIONAL CONDITIONS
1.1.1
1.4.14
1.5.5
1.7.1
1.7.7
2.5
All equipment is to be designed to allow
installation in accordance with the National
Electrical Code (NEC), ANSI/NFPA 70, the
Canadian Electrical Code (CEC), Part I,
CAN/CSA C22.1, and when applicable, the
National Electrical Safety Code, IEEE C2. Also,
unless marked or otherwise identified, installation
is allowed per the Standard for the Protection of
Electronic Computer/Data-Processing Equipment,
ANSI/NFPA 75.
For Pluggable Equipment Type A, the protection
in the installation is assumed to be 20A.
For lengths exceeding 3.05 m, external
interconnecting flexible cord and cable
assemblies are required to be a suitable cable
type (e.g., DP, CL2) specified in the CEC/NEC.
For lengths 3.05 m or less, external
interconnecting flexible cord and cable
assemblies that are not types specified in the
CEC are required to have special construction
features and identification markings.
Equipment for use on a.c. mains supply systems
with a neutral and more than one phase
conductor (e.g. 120/240 V, 3-wire) require a
special marking format for electrical ratings.
A voltage rating that exceeds an attachment plug
cap rating is only permitted if it does not exceed
the extreme operating conditions in Table 2 of
CAN/CSA C22.2 No. 235, and if it is part of a
range that extends into the Table 2 "Normal
Operating Conditions." Likewise, a voltage rating
shall not be lower than the specified "Normal
Operating Conditions," unless it is part of a range
that extends into the "Normal Operating
Conditions."
Wiring terminals intended to supply Class 2
outputs in accordance with CEC Part 1 or NEC
shall be marked with the voltage rating and
“Class 2” or equivalent. Marking shall be located
adjacent to the terminals and shall be visible
during wiring.
Where a fuse is used to provide Class 2, Limited
Power Source, or TNV current limiting, it shall not
be operator-accessible unless it is not
interchangeable.
IECEE CB Bulletin on 2008-07-31
Equipment in compliance with
IEC 60950-1. Overall
acceptance has to be
evaluated during the national
approval process.
N/A
N/A
N/A
N/A
N/A
N/A
Canadian National Differences
ATTACHMENT
National Differences
Page 60 of 68
Report No.:
11019890 001
National Differences
Clause
Requirement − Test
2.7.1
Suitable NEC/CEC branch circuit protection rated
at the maximum circuit rating is required for all
standard supply outlets and receptacles (such as
supplied in power distribution units) if the supply
branch circuit protection is not suitable.
Power distribution transformers distributing power
at 100 volts or more, and rated 10 kVA or more,
require special transformer overcurrent
protection.
Wiring methods (terminals, leads, etc.) used for
the connection of the equipment to the mains
shall be in accordance with the NEC/CEC.
Power supply cords are required to have
attachment plugs rated not less than 125 percent
of the rated current of the equipment.
Equipment connected to a centralized d.c. power
system, and having one pole of the DC mains
input terminal connected to the main protective
earthing terminal in the equipment, is required to
comply with special earthing, wiring, marking and
installation instruction requirements.
Permanent connection of equipment to the mains
supply by a power supply cord is not permitted,
except for certain equipment, such as ATMs.
Power supply cords are required to be no longer
than 4.5 m in length.
Flexible power supply cords are required to be
compatible with Tables 11 and 12 of the CEC and
Article 400 of the NEC.
Permanently connected equipment is required to
have a suitable wiring compartment and wire
bending space.
Wiring terminals and associated spacings for field
wiring connections shall comply with CSA C22.2
No. 0.
Wire binding screws are not permitted to attach
2
conductors larger than 10 AWG (5.3 mm ).
Terminals for permanent wiring, including
protective earthing terminals, are required to be
suitable for Canadian/US wire gauge sizes, rated
125 percent of the equipment rating, and be
specially marked when specified (1.7.7).
Motor control devices are required for
cord-connected equipment with a motor if the
equipment is rated more than 12 A, or if the motor
has a nominal voltage rating greater than 120 V,
or is rated more than 1/3 hp (locked rotor current
over 43 A).
Vertically-mounted disconnect switches and
circuit breakers are required to have the "on"
position indicated by the handle in the up
position.
3.2
3.2.1
3.2.1.2
3.2.3
3.2.5
3.2.9
3.3
3.3.3
3.3.4
3.4.2
3.4.8
IECEE CB Bulletin on 2008-07-31
Result – Remark
Verdict
N/A
N/A
No power supply cords
provided.
N/A
N/A
N/A
No power supply cords
provided.
N/A
N/A
N/A
No wire binding screws.
N/A
N/A
Equipment is not such a
device.
N/A
No such device incorporated.
N/A
Canadian National Differences
ATTACHMENT
National Differences
Page 61 of 68
Report No.:
11019890 001
National Differences
Clause
Requirement − Test
Result – Remark
3.4.11
For computer room applications, equipment with
battery systems capable of supplying 750 VA for
five minutes are required to have a battery
disconnect means that may be connected to the
computer room remote power-off circuit.
The maximum quantity of flammable liquid stored
in equipment is required to comply with NFPA 30.
Equipment with lasers is required to meet the
Canadian Radiation Emitting Devices Act, REDR
C1370 and/or Code of Federal Regulations 21
CFR 1040, as applicable.
For computer room applications, automated
information storage systems with combustible
3
media greater than 0.76 m (27 cu ft) are required
to have a provision for connection of either
automatic sprinklers or a gaseous agent
extinguishing system with an extended discharge.
For computer room applications, enclosures with
combustible material measuring greater than 0.9
2
m (10 sq ft) or a single dimension greater than
1.8 m (6 ft) are required to have a flame spread
rating of 50 or less. For other applications,
enclosures with the same dimensions require a
flame spread rating of 200 or less.
Equipment that produces ionizing radiation is
required to comply with the Canadian Radiation
Emitting Devices Act, REDR C1370 and/or Code
of Federal Regulations, 21 CFR 1020, as
applicable.
Not such an application.
4.3.12
4.3.13.5
4.7
4.7.3.1
Annex H
Verdict
N/A
N/A
No laser contained.
N/A
Not such an application.
N/A
Not such an application.
N/A
N/A
OTHER DIFFERENCES
1.5.1
Some components and materials associated with Complied.
the risk of fire, electric shock, or personal injury
are required to have component or material
ratings in accordance with the applicable national
(Canadian and/or U.S.) component or material
standard requirements. These components
include:
attachment plugs, battery packs (rechargeable
type, used with transportable equipment),
cathode ray tubes, circuit breakers,
communication circuit accessories, connectors
(used for current interruption of non-LPS circuits),
cord sets and power supply cords, direct plug-in
equipment, enclosures (outdoor), flexible cords
and cables, fuses (branch circuit), fuseholders,
ground-fault current interrupters, industrial control
equipment, insulating tape, interconnecting
cables, lampholders, limit controls, printed wiring,
protectors for communications circuits,
receptacles, solid state controls, supplementary
protectors, switches (including interlock
switches), thermal cutoffs, thermostats, (multi-
IECEE CB Bulletin on 2008-07-31
P
Canadian National Differences
ATTACHMENT
National Differences
Page 62 of 68
Report No.:
11019890 001
National Differences
Clause
1.6.1.2
2.3.1
2.3.2.1
2.6.3.4
4.2.8.1
4.2.11
4.3.2
5.1.8.3
5.3.7
Requirement − Test
layer) transformer winding wire, transient voltage
surge suppressors, tubing, wire connectors, and
wire and cables.
A circuit for connection to the DC Mains Supply is
classified as either a SELV Circuit, TNV-2 Circuit
or Hazardous Voltage Circuit depending on the
maximum operating voltage of the supply. This
maximum operating voltage shall include
consideration of the battery charging “float
voltage” associated with the intended supply
system, regardless of the marked power rating of
the equipment.
For TNV-2 and TNV-3 circuits with other than
ringing signals and with voltages exceeding 42.4
Vpeak or 60 Vd.c., the maximum acceptable
current through a 2000 ohm resistor (or greater)
connected across the voltage source with other
loads disconnected is 7.1 mA peak or 30 mA d.c.
under normal operating conditions.
In the event of a single fault between TNV and
SELV circuits, the limits of 2.2.3 apply to SELV
Circuits and accessible conductive parts.
Protective bonding conductors of non-standard
protective bonding constructions (e.g., printed
circuit traces) may be subjected to the additional
limited short circuit test conditions specified.
Enclosures around CRTs with a face diameter of
160 mm or more are required to reduce the risk of
injury due to the implosion of the CRT.
For equipment intended for mounting on racks
and provided with slide/rails allowing the
equipment to slide away from the rack for
installation, service and maintenance, additional
construction, performance and marking
requirements are applicable to determine the
adequacy of the slide/rails.
Equipment with handles is required to comply
with special loading tests.
Equipment intended to receive
telecommunication ringing signals is required to
comply with a special touch current measurement
tests.
Internal (e.g., card cage) SELV circuit connectors
and printed wiring board connectors that are
accessible to the operator and that deliver power
are to be overloaded.
During abnormal operating testing, if a circuit is
interrupted by the opening of a component, the
test shall be repeated twice (three tests total)
using new components as necessary.
IECEE CB Bulletin on 2008-07-31
Result – Remark
Verdict
N/A
No TNV circuits.
N/A
No TNV circuits.
N/A
N/A
N/A
N/A
N/A
Not applicable for this
equipment.
N/A
N/A
Canadian National Differences
ATTACHMENT
National Differences
Page 63 of 68
Report No.:
11019890 001
National Differences
Clause
Requirement − Test
6.4
Equipment intended for connection to
telecommunication network outside plant cable is
required to be protected against overvoltage from
power line crosses in accordance with 6.4 and
Annex NAC.
Continuous ringing signals up to 16 mA only are
permitted if the equipment is subjected to special
installation and performance restrictions.
Equipment connected to a telecommunication
and cable distribution networks and supplied with
an earphone intended to be held against, or in the
ear is required to comply with special acoustic
pressure requirements.
Document (paper) shredders likely to be used in
a home or home office (Pluggable Equipment
Type A plug configuration) are required to comply
with additional requirements, including
markings/instructions, protection against
inadvertent reactivation of a safety interlock,
disconnection from the mains supply (via
provision of an isolating switch), and protection
against operator access (accessibility determined
via new accessibility probe & probe/wedge).
M.2
Annex
NAD
Annex
NAF
IECEE CB Bulletin on 2008-07-31
Result – Remark
Verdict
N/A
N/A
N/A
N/A
Canadian National Differences
ATTACHMENT
National Differences
Page 64 of 68
Report No.:
11019890 001
National Differences
Clause
Requirement − Test
Result – Remark
Verdict
Korean National Differences
P
Corresponding National Standard: K 60950-1
P
1.5.101
Addition:
Plugs for the connection of the apparatus to the
supply mains shall comply with the Korean
requirement (KSC 8305).
No power supply cords
provided.
N/A
8
Addition: EMC
The apparatus shall comply with the relevant
CISPR standards.
Compliance shall be evaluated
during the national approval.
N/A
IECEE CB Bulletin on 2007-05-29
Korean National Differences
ATTACHMENT
National Differences
Page 65 of 68
Report No.:
11019890 001
National Differences
Clause
Requirement − Test
Result – Remark
Verdict
US National Differences
P
SPECIAL NATIONAL CONDITIONS BASED ON FEDERAL REGULATIONS
1.1.1
1.4.14
1.5.5
1.7.1
2.5
2.7.1
3.2
3.2.1
3.2.1.2
3.2.3
All equipment is to be designed to allow
installation in accordance with the National
Electrical Code (NEC), ANSI/NFPA 70, and when
applicable, the National Electrical Safety Code,
IEEE C2. Also, unless marked or otherwise
identified, installation is allowed per the Standard
for the Protection of Electronic Computer/DataProcessing Equipment, ANSI/NFPA 75.
For Pluggable Equipment Type A, the protection
in the installation is assumed to be 20A.
For lengths exceeding 3.05 m, external
interconnecting flexible cord and cable
assemblies are required to be a suitable cable
type specified in the NEC. For lengths 3.05 m or
less, external interconnecting flexible cord and
cable assemblies that are not types specified in
the NEC are required to have special construction
features and identification markings.
Equipment for use on a.c. mains supply systems
with a neutral and more than one phase
conductor (e.g. 120/240 V, 3-wire) require a
special marking format for electrical ratings.
Where a fuse is used to provide Class 2, Limited
Power Source, or TNV current limiting, it shall not
be operator-accessible unless it is not
interchangeable.
Suitable NEC branch circuit protection rated at
the maximum circuit rating is required for all
standard supply outlets and receptacles (such as
supplied in power distribution units) if the supply
branch circuit protection is not suitable. Power
distribution transformers distributing power at 100
volts or more, and rated 10 kVA or more, require
special transformer overcurrent protection.
Wiring methods (terminals, leads, etc.) used for
the connection of the equipment to the mains
shall be in accordance with the NEC.
Power supply cords are required to have
attachment plugs rated not less than 125 percent
of the rated current of the equipment.
Equipment connected to a centralized d.c. power
system, and having one pole of the DC mains
input terminal connected to the main protective
earthing terminal in the equipment, is required to
comply with special earthing, wiring, marking and
installation instruction requirements.
Permanent connection of equipment to the mains
supply by a power supply cord is not permitted,
except for certain equipment, such as ATMs.
IECEE CB Bulletin on 2007-08-08
Equipment in compliance with
IEC 60950-1. Overall
acceptance has to be
evaluated during the national
approval process.
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
US National Differences
ATTACHMENT
National Differences
Page 66 of 68
Report No.:
11019890 001
National Differences
Clause
Requirement − Test
3.2.5
Power supply cords are required to be no longer
than 4.5 m in length and minimum length shall be
1.5 m. Flexible power supply cords are required
to be compatible with Article 400 of the NEC.
Permanently connected equipment must have a
suitable wiring compartment and wire bending
space.
Wire binding screws are not permitted to attach
conductors larger than 10 AWG (5.3 mm2).
Terminals for permanent wiring, including
protective earthing terminals, must be suitable for
U.S wire gauge sizes, rated 125 percent of the
equipment rating, and be specially marked when
specified (1.7.7).
Motor control devices are required for cordconnected equipment with a motor if the
equipment is rated more than 12 A, or if the motor
has a nominal voltage rating greater than 120 V,
or is rated more than 1/3 hp (locked rotor current
over 43 A).
Vertically-mounted disconnect switches and
circuit breakers are required to have the "on"
position indicated by the handle in the up
position.
For computer room applications, equipment with
battery systems capable of supplying 750 VA for
five minutes are required to have a battery
disconnect means that may be connected to the
computer room remote power-off circuit.
The maximum quantity of flammable liquid stored
in equipment is required to comply with NFPA 30.
Equipment with lasers is required to meet the
Code of Federal Regulations 21 CFR 1040.
For computer room applications, automated
information storage systems with combustible
media greater than 0.76 m3 (27 cu ft) are
required to have a provision for connection of
either automatic sprinklers or a gaseous agent
extinguishing system with an extended discharge.
For computer room applications, enclosures with
combustible material measuring greater than 0.9
m2 (10 sq ft) or a single dimension greater than
1.8 m (6 ft) are required to have a flame spread
rating of 50 or less. For other applications,
enclosures with the same dimensions require a
flame spread rating of 200 or less.
Equipment that produces ionizing radiation must
comply with Federal Regulations, 21 CFR 1020
3.2.9
3.3.3
3.3.4
3.4.2
3.4.8
3.4.11
4.3.12
4.3.13.5
4.7
4.7.3.1
Annex H
IECEE CB Bulletin on 2007-08-08
Result – Remark
Verdict
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
US National Differences
ATTACHMENT
National Differences
Page 67 of 68
Report No.:
11019890 001
National Differences
Clause
Requirement − Test
Result – Remark
1.5.1
Some components and materials associated with Complied.
the risk of fire, electric shock, or personal injury
are required to have component or material
ratings in accordance with the applicable national
(U.S. and Canadian) component or material
requirements. These components include:
attachment plugs, battery packs (rechargeable
type, used with transportable equipment),
cathode ray tubes, circuit breakers,
communication circuit accessories, connectors
(used for current interruption of non-LPS circuits),
cord sets and power supply cords, direct plug-in
equipment, enclosures (outdoor), flexible cords
and cables, fuses (branch circuit), fuseholders,
ground-fault current interrupters, industrial control
equipment, insulating tape, interconnecting
cables, lampholders, limit controls, printed wiring,
protectors for communications circuits,
receptacles, solid state controls, supplementary
protectors, switches (including interlock
switches), thermal cutoffs, thermostats, (multilayer) transformer winding wire, transient voltage
surge suppressors, tubing, wire connectors, and
wire and cables.
A circuit for connection to the DC Mains Supply is
classified as either a SELV Circuit, TNV-2 Circuit
or Hazardous Voltage Circuit depending on the
maximum operating voltage of the supply. This
maximum operating voltage it to include
consideration of the battery charging “float
voltage” associated with the intended supply
system, regardless of the marked power rating of
the equipment.
For TNV-2 and TNV-3 circuits with other than
ringing signals and with voltages exceeding 42.4
Vpeak or 60 Vd.c., the max. acceptable current
through a 2000 ohm resistor (or greater)
connected across the voltage source with other
loads disconnected is 7.1 mA peak or 30 mA d.c.
under normal operating conditions.
In the event of a single fault between TNV and
SELV circuits, the limits of 2.2.3 apply to SELV
Circuits and accessible conductive parts.
Protective bonding conductors of non-standard
protective bonding constructions (e.g., printed
circuit traces) may be subjected to the additional
limited short circuit test conditions specified.
Enclosures around CRTs with a face diameter of
160 mm or more are required to reduce the risk of
injury due to the implosion of the CRT.
Verdict
OTHER NATIONAL DIFFERENCES
1.6.1.2
2.3.1
2.3.2.1
2.6.3.4
4.2.8.1
IECEE CB Bulletin on 2007-08-08
P
N/A
N/A
N/A
N/A
N/A
US National Differences
ATTACHMENT
National Differences
Page 68 of 68
Report No.:
11019890 001
National Differences
Clause
Requirement − Test
4.2.11
For equipment intended for mounting on racks
and provided with slide/rails allowing the
equipment to slide away from the rack for
installation, service and maintenance, additional
construction, performance and marking
requirements are applicable to determine the
adequacy of the slide/rails.
Equipment with handles is required to comply
with special loading tests.
Equipment intended to receive
telecommunication ringing signals is required to
comply with a special touch current measurement
tests.
Internal (e.g., card cage) SELV circuit connectors
and printed wiring board connectors that are
accessible to the operator and that deliver power
are to be overloaded. During abnormal operating
testing, if a circuit is interrupted by the opening of
a component, the test shall be repeated twice
(three tests total) using new components as
necessary.
Equipment intended for connection to
telecommunication network outside plant cable is
required to be protected against overvoltage from
power line crosses in accordance with 6.4 and
Annex NAC.
Continuous ringing signals up to 16 mA only are
permitted if the equipment is subjected to special
installation and performance restrictions.
Equipment connected to a telecommunication
and cable distribution networks and supplied with
an earphone intended to be held against, or in the
ear is required to comply with special acoustic
pressure requirements.
Document (paper) shredders likely to be used in
a home or home office (Pluggable Equipment
Type A plug configuration) are required to comply
with additional requirements, including
markings/instructions, protection against
inadvertent reactivation of a safety interlock,
disconnection from the mains supply (via
provision of an isolating switch), and protection
against operator access (accessibility determined
via new accessibility probe & probe/wedge).
4.3.2
5.1.8.3
5.3.7
6.4
M.2
Annex
NAD
Annex
NAF
IECEE CB Bulletin on 2007-08-08
Result – Remark
Verdict
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
US National Differences
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement