1 - TOPCOMED
FRONT COVER
USER MANUAL
COMPUTERIZED LENSMETER
CL-300
INTRODUCTION
Thank you for purchasing the TOPCON Computerized Lensmeter CL-300.
FEATURES
This instrument has the following features:
• High accuracy measurements with ease of operation
• The LCD touch panel will facilitate operation
PURPOSE OF THIS MANUAL
This Instruction Manual covers an overview of the TOPCON Computerized Lensmeter CL300, basic operations, troubleshooting, maintenance and cleaning.
To ensure the efficient, safe use, read through “DISPLAYS AND SYMBOLS FOR SAFE USE”
and “GENERAL SAFETY INFORMATION” and use the instrument correctly.
Keep this Instruction Manual within reach for future reference.
1
1. No part of this manual may be copied or reprinted, in whole or in part, without
prior written permission.
2. The contents of this manual are subject to change without prior notice and without legal obligation.
3. The contents of this manual are correct to the best of our knowledge. Please
inform us of any ambiguous or erroneous descriptions, missing information, etc.
©2012 TOPCON CORPORATION
ALL RIGHTS RESERVED
2
CONTENT
INTRODUCTION ........................................................................................................1
GENERAL SAFETY INFORMATION..........................................................................5
HOW TO READ THIS MANUAL .................................................................................6
GENERAL MAINTENANCE INFORMATION .............................................................6
USER MAINTENANCE...............................................................................................6
DISCLAIMERS ...........................................................................................................6
DISPLAYS AND SYMBOLS FOR SAFE USE ............................................................7
SYMBOLS ..................................................................................................................7
WARNING INDICATIONS AND POSITIONS .............................................................8
COMPONENTS
ACCESSORIES ..........................................................................................................9
COMPONENT NAMES.............................................................................................10
COMPARTMENT SPACE.........................................................................................11
OPERATION METHOD OF CONTROL ...................................................................11
CONTROL PANEL COMPONENTS.........................................................................12
MEASUREMENT SCREEN ......................................................................................14
SETUP SCREEN ......................................................................................................17
PREPARATION
INSTALLATION ........................................................................................................18
SETTING THE PAPER .............................................................................................19
AUTO POWER SAVE FUNCTION ...........................................................................20
USING THE INSTRUMENT
CHECKING BEFORE MEASURING ........................................................................21
SETTING OF A LENS ..............................................................................................21
MEASURING A SINGLE FOCAL LENS ...................................................................22
MEASURING A PROGRESSIVE LENS ...................................................................24
MEASURING BI-FOCAL AND TRI-FOCAL LENSES...............................................28
MEASURING BI-FOCAL AND TRI-FOCAL LENSES (MEASURING THE DIOPTER
POWER OF LENSES WITH THE CONCAVE SIDE UP) .........................................29
MEASURING A CONTACT LENS ............................................................................30
A:STEP MODE .........................................................................................................32
UV TRANSMISSION MEASUREMENT....................................................................32
AXIS MARKING
(CARTRIDGE SPECIFICATION/STEEL NEEDLE SPECIFICATION) .....................34
PRINTING ADDITIONAL TEXTBOX (WITH PRINTER SPECIFICATION) ..............37
SETTING A SEQUENCE NO. ..................................................................................38
LENS PROTECTION PAD .......................................................................................38
MEASURING PD (PD FITTING) (WITH PD SPECIFICATION)................................39
HOW TO OUTPUT DATA.........................................................................................41
3
SETTING FUNCTIONS ON SETUP SCREEN
OPERATING THE SETUP SCREEN........................................................................42
LIST OF SETUP ITEMS ...........................................................................................45
MAINTENANCE ........................................................................................................49
BEFORE REQUESTING SERVICE
CAUTION MESSAGES ............................................................................................51
CHECK ITEMS .........................................................................................................51
SPECIFICATIONS
SPECIFICATIONS ....................................................................................................52
WITH PRINTER SPECIFICATION ...........................................................................52
OPTIONAL ACCESSORIES.....................................................................................52
GENERAL INFORMATION ON USAGE AND MAINTENANCE
ENVIRONMENTAL CONDITIONS FOR USE ..........................................................53
STORAGE, USAGE PERIOD AND OTHERS ..........................................................53
SAFETY DESIGNATIONS PER IEC 60601-1 STANDARD .....................................53
MAINTENANCE AND CHECKS ...............................................................................54
DISPOSAL ................................................................................................................54
INTENDED USER PROFILE ....................................................................................54
ELECTROMAGNETIC COMPATIBILITY..................................................................55
SHAPE OF PLUG .....................................................................................................59
USING THE INSTRUMENT AS A SYSTEM
ON - LINE SYSTEM .................................................................................................60
4
GENERAL SAFETY INFORMATION
WARNINGS
Preventing Electric Shocks and Fire
To avoid fire and electric shocks, do not place a cup or vessel containing water/fluid on the
instrument.
To avoid electric shocks, do not insert objects through vent holes or gaps or force them
inside the machine body.
To avoid electric shocks, do not attempt disassembling, rebuilding or repairing. For repairs,
call your dealer.
To avoid fire/electric shocks, do not install the instrument in a place where it may get wet.
If there is a malfunction or if the instrument produces smoke, immediately turn OFF the
POWER switch and unplug the power cable. To a avoid a possible fire due to malfunction,
call your dealer and ask for repairs.
CAUTIONS
Ensuring the Safety of Patients and Operators
To avoid injury by falling, do not install the instrument on a slope or in an unstable place.
Preventing Electric Shocks and Fire
Do not open the cover. For repairs, contact your Topcon dealer.
[The instrument may injure someone by electric shock.]
Electromagnetic Compatibility (EMC)
This instrument has been tested (with120V/ 230V) and found to comply with IEC60601-1-2
Ed.3.0:2007. This instrument radiates radio frequency energy within standard and may affect
other devices in vicinity. If you have found out by turning on/off the instrument that it affects
other devices, it is recommended to change the direction, keep a proper distance against
other devices or change the outlet. If you have a question, consult with the selling agent.
5
HOW TO READ THIS MANUAL
• Read the instructions on pages 5 to 8 before using the machine.
• If you would like an overview of the system, begin by reading "USING THE INSTRUMENT"(page 21).
• For setting various functions, see "SETTING FUNCTIONS ON SETUP SCREEN" on page
42.
GENERAL MAINTENANCE INFORMATION
USER MAINTENANCE
To maintain the safety and performance of the equipment, never attempt to repair or perform
maintenance. These tasks should be performed by an authorized service representative.
Maintenance tasks that can be performed by the user are as follows; for details, follow the
manual’s instructions.
CLEANING COVER GLASSES
For details, see page 50 of this manual.
DISCLAIMERS
• TOPCON shall not take any responsibility for damages due to fire, groundquake, actions by
third person, or the negligence and misuse by the user and used under unusual conditions.
• TOPCON shall not take any responsibility for damage derived from the inability to use this
equipment, such as a loss of business profit and suspension of business.
• TOPCON shall not take any responsibility for damage caused by operations other than
those described in this Instruction Manual.
6
DISPLAYS AND SYMBOLS FOR SAFE USE
In order to encourage the safe use of this product, warnings labels are placed on the product and
written in the instruction manual.
We suggest that everyone understands the meaning of the following displays and icons before
reading the “GENERAL SAFETY INFORMATION” and text.
DISPLAYS
Display
Meaning
WARNINGS
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTIONS
Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
NOTES
Useful functions to know and attentions to prevent
troubles are noted.
SYMBOLS
Symbol
IEC/ISO Publication
Description
IEC 60417-5032
Alternating Current
Description (French)
Courant alternatif
IEC 60417-5008
Off (power: disconnection
Éteint (courant: coupure
from the main power supply) avec le secteur)
IEC 60417-5007
On (power: connection to
the main power supply)
Allumé (courant: raccordement sur le secteur)
ISO 7010-W001
General warning sign
Symbole d'avertissement
général
7
WARNING INDICATIONS AND POSITIONS
To insure safety, warning labels are provided.
Use the equipment correctly by following the warning instructions. If any of the following labels
are missing, please contact us at the address stated on the back cover.
1
No.
1
Label
Meaning
WARNING
To avoid injury caused by electric shock, do not open the cover.
Ask your dealer for service.
WARNING
To avoid injury, do not touch the AC adapter jack while using the
AC adapter.
8
COMPONENTS
ACCESSORIES
The following are standard accessories. Make sure that all these items are included (quantity).
Power cable (1)
Lens protection pad (1)
AC adapter (1) Model name: BPM040S09F02
Silicon cloth (1)
Contact lens support (1)
Dust cover (1)
Printer paper (2)
(with printer specification)
User manual (1)
Instruction manual (1)
INSTRUC
COMPUT TION MANU
AL
ERIZED
LENSME
TER
CL-30
0
Guarantee sheet (1)
9
COMPONENTS
COMPONENT NAMES
with PD
Back side
Nose reset
Port cover
LCD
Power LED
Power switch
Axis marker lever
Marking ink
cartridge
Lens retainer
Lens table
Lens support
RS-232C
IN
Lens table
lever
MEMORY button
AC adapter
jack
OUT
USB
IN
OUT
*LAN
Printer
cover
*The model without LAN is also provided.
• Use a LAN cable within 30m.
• The USB is for maintenance, not used normally.
• Power LED
Orange lamp ON: Power OFF
Green lamp ON:
Power ON
Green lamp blinks: Under power save
• The model without PD and LAN function is not provided nose-pad and LAN.
10
COMPONENTS
COMPARTMENT SPACE
A space for keeping the contact lens holder, printer paper, etc. is secured in the back.
OPERATION METHOD OF CONTROL
The control panel is a touch panel. Do not use any sharp tools; e.g. ball point pen.
Tap
To select any relevant item.
Touch the screen softly with a finger.
Continue to press
Used for long button press.
Continue to touch the screen softly with a finger.
11
COMPONENTS
CONTROL PANEL COMPONENTS
THE FUNCTION BUTTONS
The control panel is designed as a touch panel for performing various operations and settings.
It displays images and shows information, including set conditions and measurement results.
SINGLE MODE
R button
S button
Measurement mode
Settings button
CLEAR button
+/- button
PRINT button
STEP button
Prism button
UV button
R/L MODE
L button
12
COMPONENTS
R button
BUTTON NAMES
Settings button
Displays the SETUP screen.
+/- button
Used to change the degree (performed when an orange frame
is displayed).
STEP button
Used to change the step of measurement value.
(Press it long time for A:step setting.)
Long button press:
Prism button
Used to change the prism display.
UV button
Used to change ON/OFF of UV measurement.
(performed when an orange frame is displayed).
PRINT button
Press to obtain a print out readings.
Press to output data trough RS-232C.
CLEAR button
Used to delete all data in memory.
To delete R and L separately, hold the button down.
Measurement mode button
Used to change the setting of measurement mode.
13
COMPONENTS
MEASUREMENT SCREEN
SINGLE MODE
Lens measurement value
Target
Message bar
OFF CENTER
ERROR
ALIGNMENT OK
MARKING OK
Setup icon
Refer to
LIST OF SETUP ITEMS
R/L MODE
Measurement value of
left-eye lens
Measurement value of
right-eye lens
• When saved, S/R/L changes the color and stops.
• When the measurement value turns white, the measurement is finished.
• When the measurement value is yellow, the measurement of a multi-focal lens is being performed.
14
COMPONENTS
TARGET
Optical center's off.
[OFF CENTER] is displayed
when the optical center is off
by 4 or more.
Blue: , measurement value
[ALIGNMENT OK]
mark appears when the
lens is ready for measurement.
Green: , measurement value
[MARKING OK]
Place in
mark, the lateral
line will extend, getting the
instrument ready for marking.
Pink: , measurement value
The target indicates optical center position.
And it varies depending on the symbol used in the spherical equivalent power.
Be noted that the target motion is different from that of Topcon telescopic lensmeters.
For axis marking procedures, don't use target's position but the prism value.
Refer the instruction in Page 27.
15
COMPONENTS
RESULT DISPLAY
When INITIAL/DISPLAY/NORMAL is selected, the display is normal.
When INITIAL/DISPLAY/HORIZONTAL LARGE is selected, the SCA display is horizontally
enlarged.
When INITIAL/DISPLAY/VERTICAL LARGE is selected, the SCA display is vertically
enlarged. The graphic moves to the opposite side.
16
COMPONENTS
SCREEN PRINT DISPLAY: (WHEN ENLARGED)
For framed lenses, of which both R and L are memorized, pressing the PRINT button enlarges
the SCA of both eyes. To return to the original state, tap the
button.
The button which is not allowed change.
• When the setting is PRINT/AUTO PRINT/ON , printing is performed automatically after saving the measurement value of both eyes.
• By tapping the
button, the measurement screen is returned, leaving measurement values as saved.
• By tapping the
surement values.
button, the measurement screen is returned, clearing mea-
SETUP SCREEN
The Setup screen is displayed by tapping the Settings button
on Measurement screen.
17
COMPONENTS
PREPARATION
INSTALLATION
1
2
3
WARNING
To avoid fire/electric shocks, connect the power plug to a 3P
AC outlet (with ground) and secure grounding.
CAUTION
To avoid injury by falling, do not install the instrument on a
slope or in an unstable place.
Remove the tape from the lens support.
Remove the tape from the marking ink cartridge.
Remove the port cover. Push the etched mark and move the cover to the arrow direction.
Etched mark
4
5
6
Plug in the power cable to the AC adapter.
Pass the cable through the cable clamp.
Connect the AC adapter plug to the AC adapter jack located on the rear panel of the main
body.
IN
OUT
AC adapter cable
Cable clamp
18
PREPARATION
7
Setting the Port Cover.
Etched mark
The stop to be
fitted first
Fit the stop of the figure above to the
main body. After fitting the stop, turn
the cover along the arrow direction.
Fit the stop by pushing the etched mark.
By connecting an AC adapter, the main body starts automatically.
SETTING THE PAPER
1
Press the PRINTER button and open the cover.
2
Open the printer cover to the limit.
19
PREPARATION
3
Insert the printer paper in the direction shown below and pull out the paper end to your
side by 7 to 8cm.
4
Bring the paper into the center, then close the printer cover.
• Printer feed function: Hold PRINTER button down.
• In case the printer cover is not firmly closed, printing will not start.
• A 58mm wide paper roll (example: TP-50KJ-R [Nippon Paper Co.]) is recommended.
Other paper rolls may cause abnormal printing noise or unclear print.
AUTO POWER SAVE FUNCTION
1
When switch/tap operations are not done for about 10 minutes, or if no patient lens is set,
power save starts automatically.
2
3
During power save, the screen saver is actuated.
4
For reset, either tap the monitor, or press the Memory button, or press the Power switch
When the Memory button
is pressed continuously for more than 2 seconds, the
backlight of the monitor goes off and the Power switch LED blink.
. Incidentally, press the Power switch
power is shut off
5
6
short, or if pressed and held long, the
If auto power save function is not required, select INITIAL/AUTO OFF/NO .
To actuate power save manually, press the Memory button
20
PREPARATION
longer than 2 seconds.
USING THE INSTRUMENT
CHECKING BEFORE MEASURING
1
2
3
Check to see that there is no lens on the lens support.
Turn on the power switch.
Display will appear on the screen in a few seconds.
The ERROR screen will appear when there is a
lens left on the lens support or dust left on the
cover glass. Remove the lens or dust.
By tapping the screen, the error screen is cleared.
SETTING OF A LENS
A SINGLE LENS SETTING
1
2
3
Place the lens with the concave surface facing down on the lens support.
Lift and place down the lens retainer.
When holding a sharp-curve lens, provide your hand in case the lens falls.
A FRAMED LENS SETTING
1
2
Place the flamed lens on the lens support.
3
Lift and place down the lens retainer.
Turn the lens table lever and place the glass frame
against the lens table for measurement.
Alignment
Right and left....Place the frame against the lens
table, and move the frame right
and left finely.
Vertically ..........Move the table finely with the
lens table lever.
21
USING THE INSTRUMENT
MEASURING A SINGLE FOCAL LENS
When a measurement mode button is
, a single focal lens can be measured.
INITIAL/PROGRESSIVE/AUTO , INITIAL/PROGRESSIVE/OFF
1
2
Move the lens and move the target near the center.
ALIGNMENT OK will be displayed when the target image center is within the minimum circle (0.5
3
or smaller).
The MARKING OK is displayed when the target image center is reached. If
is displayed, "single focal lens" is memorized automatically.
When BEEP function is ON, the buzzer will sound.
(Note) The target may move in a contrary manner immediately after the lens is placed.
WHEN R/L DESIGNATION IS REQUIRED:
Tap the R button. The R/L display screen is displayed.
By tapping the L button, L is displayed. By tapping the CLEAR button, S is returned.
Single lens
R lens
R button
CLEAR button
CLEAR button
L button
R button
L lens
• When the setting is INITIAL/AUTO R/L/ R/L , the Single Lens screen is
returned by tapping the CLEAR button.
• By tapping the CLEAR button, saved measurement values are cleared.
22
USING THE INSTRUMENT
MANUAL SAVING:
Press the Memory button
. The flicker-zooming “S” stops at the zoomed-up state and the
color is changed. (When R/L is displayed, R and L are changed.)
• When printing
Tap the PRINT button
. When connecting with computer, data is transmitted.
MEASURING A FRAMED LENS
• When INITIAL/AUTO R/L OFF
Tap the R button.
is set. (
is not displayed):
First align the right lens and press the Memory button
Tap the L button.
Align the left lens and press the Memory button
• When INITIAL/AUTO R/L / R/L
.
.
& INITIAL/AUTO MEMORY/ON
is set.
(
are displayed):
*Measurement of framed lens.
First, align the right lens to display “MARKING OK”. Then the result is automatically memorized, when the right lens is hold.
Removing the right lens will automatically move to the L measurement.
Align the left lens, then the result is automatically memorized, when the left lens is hold.
• When INITIAL/AUTO R/L/ R/L & INITIAL/AUTO MEMORY/ S:OFF R/L:ON
is set.
(
are displayed):
*Measurement of single lens/framed lens
Tap the R button. (
is displayed)
At first, align the right lens to display "MARKING OK". Then the result is automatically memorized, when the right lens is hold.
Removing the right lens will automatically move to the L measurement.
Align & hold the left lens. The result is automatically memorized.
23
USING THE INSTRUMENT
MEASURING A PROGRESSIVE LENS
When a measurement mode button is
or
When auto progressive recognition mode is on.
, a progressive lens can be measured.
INITIAL/PROGRESSIVE/AUTO
Discrimination of single focal lens and progressive focal lens can be done, which is not
easily possible from appearance.
When progressive only is set.
INITIAL/PROGRESSIVE/PROGRESSIVE ONLY
The auto progressive recognition measurement can be omitted. Start measurement from
step 3 below.
1
Measure the lower frame center
The figure blinks and
the size changes.
(position in the measurement mode button 1 );
If the measurement is finished, Measurement mode button
changes to
2
.
Measure the frame center
(position in the measurement mode button 2 );
If the difference is over 0.50D or more, the screen changes.
The figure blinks and
the size changes.
3
Measure progressive lens for distance vision. (Excluding horizontal prism prescription
lenses) By moving the frame in all directions along the arrow mark displayed on the
screen, align with
.
24
USING THE INSTRUMENT
4
When the distance vision measurement is obtained and saved, the screen automatically
changes to the near vision measurement display.
(The distance vision region can be easily detected, as you repeat moving and stopping
the lens little by little at measuring.)
• By pressing the Memory button
, you may manually store
the result of distance vision power measurement. The screen
will then switch to the near vision measurement.
When
is selected as the
INITIAL/FAR MEMORY/OFF
default setting, the result of the distance vision measurement is
not automatically stored. With this setting, you must press the
Memory button
to save the distance vision.
• For high-power lenses, sometimes the distance vision region
cannot be easily detected. In this case, obtain the measurement in the approximate position that is shown on the above, and then press Memory button
.
10mm approx.
• For horizontal prism prescription lenses, press the MEMORY button
distance reference point.
at the
eye point
10mm approx.
5
Measure progressive lens for near vision.
While watching the screen, draw out the lens table forward: the bar-meter extends and the
“+” appears. To bring this “+” to the bar-meter center, swing the lens right-left and extend
the bar-meter.
25
USING THE INSTRUMENT
6
The condition illustrated below indicates that a position outside of the progressive zone is
being measured. Move the lens in the direction of the arrow to bring the "+" into the center
of the progressive zone.
7
8
The “+” becomes larger as it comes closer to the near vision position.
The ADD power is saved, the progressive lens measurement is completed.
Knock-out black
1.42
• By pressing the MEMORY button
, you may manually store the result of
near vision power measurement.
When INITIAL/NEAR MEMORY/OFF
is selected as the default setting, the
result of the near vision measurement is not automatically stored. With this setting, you must press the MEMORY button
to save the near vision.
• When measuring a lens mounted in a large frame,
the ADD power may be higher because some lenses
increase the ADD power at a position below the near
vision region. Accordingly, if the lens is measured at
a point lower than the near vision eye point, the ADD
power reading may be higher. If you want to know
the accurate prescription, it is advisable to check the
measurement position at the hidden mark.
26
USING THE INSTRUMENT
ASPHERICAL RANGE PROGRESSIVE RECOGNITION
If a progressive lens is position so that the lens is outside of the progressive zone, the icon
of a screen bottom will change to
. By tapping the
button, the screen will automatically switch to the distance vision measurement screen.
This appears when measuring the aspherical range of the progressive lens.
When the
button is displayed, auto saving is not available.
MEASURING AN UNPROCESSED PROGRESSIVE LENS
As each unprocessed lens has a mark on the measuring point. Do measurement on the
mark position.
Distance vision region marked
Near vision region marked
• The measuring point for the distance or near vision region may be narrowed by
marks. Take care that the luminous flux may not be shaded during measurement.
ADD values will flicker when the luminous flux is shaded by marks or off the progressive zone at the time of measuring the near vision region.
An EX lens may not be provided with accurate measurements when measured
in the boundary.
• When the Setup screen appeared in the middle of measurement, measurement
values are cleared when the Measurement screen is returned.
27
USING THE INSTRUMENT
MEASURING BI-FOCAL AND TRI-FOCAL LENSES
When a measurement mode button is
, bi-focal and tri-focal lenses can be mea-
sured.
INITIAL/PROGRESSIVE/AUTO ,
1
INITIAL/PROGRESSIVE/OFF
Align the distance vision in the center of the target image and press the MEMORY button
.
2
Move the lens into the near vision region (bi-focal segment).
3
Press the Memory button
(Near Vision Measurement Start button in this case).
The measurement mode button is changed to
4
.
Measure the bi-focal power and press the MEMORY button
nd
To measure the 2
near vision of tri-focal lenses, storing the
matically changes the
measurement.
button to the
again.
1st
mid vision power auto-
button. Tap the button starts the near vision
ADD : +1.75
+2.50
When the Setup screen appeared in the middle of measurement, measurement
values are cleared when the Measurement screen is returned.
28
USING THE INSTRUMENT
MEASURING BI-FOCAL AND TRI-FOCAL LENSES (MEASURING THE
DIOPTER POWER OF LENSES WITH THE CONCAVE SIDE UP)
Measurement is possible when the measurement mode is
.
INITIAL/PROGRESSIVE/REVERSE
1
Set the lens with the concave side down as
usual, align the distance vision region, and
press the MEMORY button
2
Screen
.
Set the lens with the concave side up, align the
distance vision region, and press the MEMORY
button
3
Lens position
.
Leaving the lens with the concave side up, align
the near vision region and press the MEMORY
button
.
When the Setup screen appeared in the
middle of measurement, measurement
values are cleared when the Measurement screen is returned.
29
USING THE INSTRUMENT
MEASURING A CONTACT LENS
MEASURING A HARD CONTACT LENS
1
Replace the lens support with the contact lens support.
2
Select INITIAL/LENS/HARD CONTACT . Setup icon
screen.
3
Put the contact lens on contact lens support with special tweezer.
Tweezer
30
USING THE INSTRUMENT
will be displayed on the
MEASURING A SOFT CONTACT LENS WITHOUT ASTIGMATISM
A soft contact lens cannot be accurately measured because of its structure.
Although you can measure a soft contact lens power in following way, consider the
results an average and not the exact value.
1
2
Use the contact lens support for measuring as measuring a hard contact lens.
3
Pinch the soft contact lens with special tweezers to remove moisture from the lens. Put
the lens between paper and move three times to remove moisture from the surface.
Select INITIAL/LENS/SOFT CONTACT
screen.
. Setup icon
will be displayed on the
If there is moisture on the soft contact lens surface, it is not possible to measure
because the luminous flux malfunctions.
4
If there is moisture dews on the surface when the contact lens is held to the light, put the
lens in the special solution again, and repeat the above. Moreover, take care about turning
inside out. When in the normal position, the lens looks like a bowl. However, when the
lens turns inside out, the rim looks warped. If the lens is ready for measurement, place it
on the contact lens holder and observe the shape (with tweezers) for alignment. After 30
seconds or more, the lens power changes since the internal moisture evaporates, therefore, measure it as quickly as possible.
Use the hard contact mode when measuring a toric soft contact lens.
When Contact Lens is selected, the measurement mode button is changed to
, and this cannot be changed.
31
USING THE INSTRUMENT
A:STEP MODE
Select INITIAL/A:STEP/5 and hold STEP button down, change to the A:STEP
button.
The axial angle is rounded to 5°.
It is convenient for inputting the result by doing measurement with the trial lens left in the
temporary frame.
For release, press the
button long.
Return to the STEP button
, the 5° rounding is reset.
STEP of the measurement value is the state before changing to the temporary
frame (A:step).
UV TRANSMISSION MEASUREMENT
UV Transmission Measurement is available when the UV button is orange-framed
.
If not orange-framed, tap the UV button and make it orange-framed.
1
2
Move the lens and move the target near the center.
ALIGNMENT OK is displayed when the target image center is within the smallest circle
(within 0.5 ).
3
4
5
MARKING OK is displayed when the target image center is reached.
Press the Memory button
.
The SCA value is saved, and the UV transmission measurement value is displayed in a
few seconds.
After pressing the Memory button
, do not move the lens until an UV transmission measurement value is displayed.
UV transmission
measurement value
32
USING THE INSTRUMENT
CORRECTING THE UV TRANSMISSION
If UV transmission is not 100% after removing the lens, perform correction.
1
2
3
Confirm that no lens is put on the lens support.
Press and hold the UV button.
When correction is finished, the buzzer beeps.
During the UV transmission measurement/correction, do not look into the LED
irradiation part.
LED irradiation part
33
USING THE INSTRUMENT
AXIS MARKING
(CARTRIDGE SPECIFICATION/STEEL NEEDLE SPECIFICATION)
Using the cartridge, one light touch to the lens can put a clear ink mark.
MARKING A LENS WITHOUT ASTIGMATISM
1
Move the lens until the centering mark coincides with the target image completely, and
MARKING OK will appear.
Centering mark
Line extends laterally to the target
2
Depress the marking lever to mark the lens.
34
USING THE INSTRUMENT
MARKING A LENS WITH ASTIGMATISM
• Axis marking, maintaining the axis as prescribed
Align the target image with the center mark, approximating the axis angle mark to the angle as
prescribed. Finally, adjust by the numerical display of axis angle A:.
Before performing alignment, set auto memory to off.
Confirm
is not displayed at the setup icon.
Check here
Axis angle mark (every 5°)
• Marking a cylindrical axis
Match the center mark with the target image, approximating the axis angle mark to 180
degrees.
Adjust A of the axis angle to 180 degrees.
Adjust to 180°.
Axis angle mark (every 5°)
35
USING THE INSTRUMENT
MARKING A LENS WITH PRISM POWER
• When the prescription is displayed with X-Y (orthogonal
coordinates) ( INITIAL/PRISM/X-Y )
Tap the prism button and get
display.
Carry out aligning according to the prism value as
prescribed and as displayed on the screen.
I in prism value: Base In
O in prism value: Base Out
U in prism value: Base Up
D in prism value: Base Down
• When the prescription is displayed with P-B (polar coordinates) ( INITIAL/PRISM/P-B )
Tap the prism button and get
display.
Carry out aligning according to the prism value as
prescribed and as displayed on the screen.
P: Prism value
B: Base orientation
Take care that the polar coordinates are not the
same as the value on the angular scale in the
target image.
• When the unit is mm ( INITIAL/PRISM/mm
Tap the prism button and get
)
display.
The
marks show the optical center
reaches the center of measurement by moving the
lens in the arrow directions by the distance as displayed.
: 3.0mm
: 2.0mm
The position is shown in the right figure.
• 0 will be displayed if the spherical power S is around 0.
• When the prism value is more than 10 (vertical direction), the measurement
value is recognized as a reference value. For reference value, * (asterisk) is displayed at the measurement result. Measurement values recognized as reference value: SCA value, prism value, ADD value
36
USING THE INSTRUMENT
PRINTING ADDITIONAL TEXTBOX (WITH PRINTER SPECIFICATION)
On the print out with the measuring data, the user can input his own text, like office name,
address or special message. The available space is three line of 24 characters each.
Tap the PRINT/NAME/INPUT .
Text enter screen will appear.
Enter window
Tap the desired enter window, tap the
button and input with keyboard.
Setting is completed by tapping the OK button.
Printout
Printing the
additional textbox
37
USING THE INSTRUMENT
SETTING A SEQUENCE NO.
Setting is carried out when writing a sequence No. on printing paper and transferring the
serial No., using RS-232C.
Tap the INITIAL/SEQ.NO./INPUT , and the screen as shown below will appear.
Enter numerals and fix by tapping the OK button.
No printing or counting is carried out in case of 0000.
Press MEMORY button
, PRINT button
and CLEAR button
and counting will be carried out. (except for single lens).
in this order,
If the OK button is tapped without filling all 4 digits, the empty digit is saved as "0."
Example) 1 2
OK
0 0 1 2 is saved.
LENS PROTECTION PAD
The attached lens protection pad allows a soft contact with the measuring lens.
1
2
Fit the lens protection pad according to the instructions.
Select INITIAL/LENS/NORMAL(PAD) , and the measurement result will be automatically compensated.
38
USING THE INSTRUMENT
MEASURING PD (PD FITTING) (WITH PD SPECIFICATION)
1
2
Select
INITIAL/PD/ON .
Put the spectacle frame onto the nose rest.
Nose rest
Lens support
3
Align the lens until marking is OK. OK if the spectacle frame is horizontal along the lens
table line. If the spectacle frame has a camber, align it horizontally.
Errors will appear when the spectacle frame is not horizontally aligned.
RPD
4
Press the lens retainer since the lens is in contact with the lens support sideways.
Let your hand go with the spectacle frame to prevent PD value shifting.
5
Press Memory button.
39
USING THE INSTRUMENT
6
Follow the similar steps to measure the lens on the opposite side.
Totaled PD will be displayed.
7
Bring the nose rest to the extreme right and fold it. It will stick to the lens table by means of
a magnet.
Range 25~45mm on one side (minimum 0.5mm)
If the measured PD value differs from that of marking PD.
8
Difference may occur by the measurement technique and with low-power lenses having a
large camber angle.
No camber angle
Marking PD
A camber angle
0
flux
Marking
Principal point
Since the optical center of the glasses mounted for
the infinite far is searched, the measured PD value
of CL-300 is called the PD/fitting value.
40
USING THE INSTRUMENT
PD fitting
(by PD mechanism)
When the pupil is on the marking
position in the case of a concave
lens, a prism is added outside.
HOW TO OUTPUT DATA
OUTPUT USING RS232C
This instrument can output data to a PC, etc. via the RS232C interface.
1
2
3
Connect the RS232C cable to RS232C OUT.
4
5
Perform measurements.
Connect the other end of the cable to the PC., etc.
Confirm that set up of data communication settings.
For details, refer to “DATA COMMUNICATION (COMM.)” on page 47.
Tap the PRINT button
of the control panel.
Data is outputted to the connected external device.
OUTPUT USING LAN
This instrument can output data to a PC, etc. via the LAN interface.
1
2
3
Connect the network cable to LAN OUT.
4
5
Perform measurements.
Connect the other end of the cable to the PC., etc.
Confirm that set up of LAN connection settings.
For details, refer to “LAN CONNECTION (LAN)” on page 48.
Tap the PRINT button
of the control panel.
Data is outputted to the connected external device.
41
USING THE INSTRUMENT
SETTING FUNCTIONS ON SETUP SCREEN
OPERATING THE SETUP SCREEN
Various functions can be set on the SETUP screen.
PREPARATONS FOR SETTING
1
Make sure that the power cable is connected.
For connection, refer to “PREPARATION” on page 18.
2
3
Turn ON the POWER switch.
Tap the SETTINGS button
on the control panel.
SETTINGS button
The SETUP screen is displayed.
Back Page button
Page display
Next Page button
Index
Return button
Descriptions
42
SETTING FUNCTIONS ON SETUP SCREEN
Current condition button
By tapping a current condition button,
the options buttons are displayed.
OUTLINE OF SETUP SCREEN OPERATIONS
1
Tap
2
Operate the NEXT PAGE button
the page to confirm/change.
3
Tap the Current condition button of the item to be changed and find the options button.
INDEX
and select the subject of setting.
or
BACK PAGE button , as necessary, and display
Options button
4
Tap the options button and change the setting.
43
SETTING FUNCTIONS ON SETUP SCREEN
• Instead of the options button, ten-key and keyboard would be displayed.
TEN-KEY:
Tap ten-key on the screen and enter the figure. If there are several windows to enter, tap the
window to enter the figure by ten-key. Setting is complete by tapping OK .
Enter window
KEYBOARD:
Tap keyboard on the screen and enter characters. If there are several windows to enter, tap
the desired window, then enter the character by keyboard. Setting is complete by tapping
OK .
Enter window
5
After entering all setting items, save the setting items and return to the Measurement
screen by tapping the Return button
.
To return the setting to the previous status, turn off the power before tapping the
Return button
.
44
SETTING FUNCTIONS ON SETUP SCREEN
LIST OF SETUP ITEMS
Setup items are categorized into 5 large indexes.
"Initial"..................items related to the initial status after power on
"Print"...................items related to output from the internal printer
"Comm"................items related to data input/output with the external device
"LAN" ...................items related to output using the LAN
"Special"...............items related to maintenance (for service engineer only)
INITIAL (INITIAL SETTING)
Initial contains settings related to the initial status after power on.
Descriptions
LENS
DISPLAY
PROGRESSIVE
FAR MEMORY
NEAR MEMORY
Options button
Contents of setup
NORMAL
Measures a normal lens.
NORMAL (PAD)
Measures a normal lens wearing the
lens protection pad.
SOFT CONTACT
Measures a soft contact lens.
HARD CONTACT
Measures a hard contact lens.
HORIZONTAL LARGE
Horizontally enlarges the SCA display.
VERTICAL LARGE
Vertically enlarges the SCA display.
NORMAL
Normal display
OFF
Auto progressive recognition mode
OFF.
AUTO
Auto progressive recognition mode
ON.
PROGRESSIVE
ONLY
Always begins with the Progressive
zone center search mode of the progressive lens.
REVERSE
Measures the diopter power with the
concave side up.
ON
Auto memory of distance vision measurement.
OFF
Manual memory of distance vision
measurement.
ON
Auto memory of near vision measurement
OFF
Manual memory of near vision measurement
Display of
Setup icon/
Display of button
Default
NORMAL
NORMAL
AUTO
ON
ON
45
SETTING FUNCTIONS ON SETUP SCREEN
AUTO R/L
R/L
Measurement of framed lens:
Auto R/L switching
S/R/L
Measurement of single lens/framed
lens: Auto R/L switching
OFF
S/R/L switching
ON
Auto memory is ON when the lens
optical axis is aligned.
S : OFF R/L : ON
Auto memory OFF at measurement of
single lens. It is ON at measurement
of framed lens.
OFF
Auto memory OFF.
ON
UV measurement is ON
OFF
UV measurement is OFF
1% STEP
UV measurement is ON: Step 1%
5% STEP
UV measurement is ON: Step 5%
ON
Buzzer sounds when a measured
value is stored or a button is pushed.
OFF
Buzzer OFF
0.25
0.25-step measurement.
0.12
0.12-step measurement.
0.01
0.01-step measurement.
A:STEP
5
Rounds axial angle settings to 5°
PRISM
NO DISPLAY
No prism display.
X-Y
Rectangular coordinate display
P-B
Polar coordinate display
mm
mm display at PD/OFF
MIX
Mixed display
+
Plus-fixed display
-
Minus-fixed display
AUTO MEMORY
UV
UV STEP
BEEP
STEP
S/R/L
S : OFF
R/L : ON
OFF
1% STEP
ON
0.25
5
1
CYLINDER
46
SETTING FUNCTIONS ON SETUP SCREEN
X-Y
MIX
AUTO OFF
BRIGHTNESS
YES
Power save ON
NO
Power save OFF
LEVEL1
Level of LCD brightness
level 1(dark)
level 6 (bright)
LEVEL2
YES
LEVEL6
LEVEL3
LEVEL4
LEVEL5
LEVEL6
ABBE
PD
SEQ.NO.
NORMAL
50-60 Abbe
MID
40-50 Abbe
LOW
30-40 Abbe
NORMAL
ON
PD value display
OFF
No PD value display
INPUT
Serial No. print mode
ON
SETTING OF INTERNAL PRINTER (PRINT)
Print contains settings related to output from the internal printer.
Descriptions
PRINTER
AUTO PRINT
NAME
Options button
Contents of setup
ON
Printer output ON
OFF
Printer output OFF
ON
Auto memory output (S: When the
lens is removed)
R/L: When both lenses are the same
class (1st/2nd near vision of distance
vision)
OFF
Manual memory output
SET
Printing additional textbox
Display of
Setup icon/
Display of button
Default
ON
ON
DATA COMMUNICATION (COMM.)
Comm contains settings related to data input/output with the external device.
Descriptions
RS-232C
Options button
Contents of setup
NEW FORMAT
External output (NEW FORMAT)
OLD FORMAT
External output (OLD FORMAT)
STD1
External output (STD FORMAT)
Display of
Setup icon/
Display of button
Default
STD1
47
SETTING FUNCTIONS ON SETUP SCREEN
LAN CONNECTION (LAN)
LAN contains settings related to data input/output via LAN.
Descriptions
IP ADDRESS
Options button
INPUT
Contents of setup
Display of
Setup icon/
Display of button
Set the IP address of CL-300.
Set the subnet mask of CL-300.
Set the default gateway of CL-300.
• When not used, set 0.0.0.0.
SETTING1
INPUT
Set the IP address of the PC to output
data.
Set the shared name of the PC to output data.
SETTING2
INPUT
Set the folder name of the PC to output data.
• The holder name which can be set
up is in the directly under hierarchy
of a shared name.
Set the name of the user who makes
access to the PC to output data.
Set a password to make access to the
PC to output data.
SPECIAL
SPECIAL is the mode for service engineer only; it can not be accessed.
For models without LAN function, LAN connection is not possible.
48
SETTING FUNCTIONS ON SETUP SCREEN
Default
MAINTENANCE
REPLACING THE MARKING INK CARTRIDGE
(THE SAME APPLIES TO STEEL NEEDLE SPECIFICATION)
1
To replace the marking ink cartridge, remove the top screw. Pull out the cartridge while
applying pressure to it so as the spring not jump out from the inside.
Work the lens holder/stopper under the lowered condition.
When not in use, put the dust cover over the cartridge (to prevent insect damage).
2
To set the cartridge, insert the spring and keep the cartridge top well above the marking
ink holder, and then fasten the screw.
Screw
Marking ink holder
Spring
Steel needle
(optional accessory)
Marking ink
cartridge
49
MAINTENANCE
SUPPLY OF INK FOR THE OPTIONAL STEEL NEEDLE
1
2
3
4
Replenish ink when poor marking happens.
Slide laterally and pull out the inkpot.
Slide off cover from the inkpot.
Infiltrate supply ink into the sponge well.
CLEANING COVER GLASSES
If the glass is dirty as indicated by arrows, it will affect
measurement accuracy adversely. If this occurs, clean
them with the attached silicon cloth.
Remove the lens support before cleaning the cover glass.
If the mark illustrated right appears at the lower part on
the screen, it means that the cover glass is dirty.
Carry out the following operation;
1
2
Wipe off the cover glass for cleaning.
Press CLEAR and TRANS buttons simultaneously and the instrument will restart. If the
measurement screen appears, continue the operation.
CLEANING THE INSTRUMENT
1
Wipe cover with damp cloth at regular interval. Never use cleanser or other chemicals.
50
MAINTENANCE
BEFORE REQUESTING SERVICE
CAUTION MESSAGES
CLEAN THE COVER GLASS
Carry out cleaning of the cover glass.
DIOPTER OVER
PRISM OVER
ERROR
Check to see that the lens is in the measurable scope.
Check to see that the lens is free from any flaw, dust or oil.
Clean both glasses and turn power on again.
PAPER END
Printer paper is out. Load new paper.
CLOSE PRINTER COVER
Close printer cover.
UV CALIBRATION NG
Is the lens left on lens support?
Remove the lens from the lens support, and perform calibration again.
PRINTER HEAD OVER HEAT
It is possible that the temperature of a printer head is rising.
Please turn off the power, and switch on a power supply
again after waiting for a while.
PRINTER CUTTER ERROR
Please check whether the printer cover has closed or
whether there is not any foreign object in a printer.
PRINTER THERMISTOR NG
Call service engineer.
INITIAL ERROR
(ERROR CODE)
Call service engineer. The error code of four digits is displayed.
CHECK ITEMS
The instrument does not get
ready for operation even if the
power switch is turned on.
Re-plug the power cord.
Operation of a button is not
effective.
Power supply cannot be turned
off even if you push the power
switch.
Press and hold the power switch for 10 seconds or more.
Then, the power supply turns off.
S, C values are wrong.
Is the lens place with power on?
Remove the lens and turn on power again.
Is the measuring beam blocked by, dust, marks, grease, etc.
in the measured lens?
Marking is poor.
Replace the marking ink cartridge. For a lens with sharp surface curve, use the optional steel needle marking set.
The screen went out all of a
sudden.
The auto shut-off function is on.
Tap the control power, and the instrument will resume.
Pushed the PRINT button but
the printer does not work.
Is printer paper set properly?
Not inside out?
51
BEFORE REQUESTING SERVICE
SPECIFICATIONS
SPECIFICATIONS
Measurable scope
Cylinder mode
Prism mode
Contact lens
Progressive focal lens
Display screen
Frame
Menu screen
Lens diameter
Power supply
Dimensions, weight
S: 0~ 25D, C: 0~ 10D, ADD: 0~+10D (0.01/0.12/0.25)
P: 0~13 (horizontal) 0~18 (vertical) (0.01/0.12/0.25),
A: 1~180° (1°)
MIX/-/+
No display / X-Y (Rectangular coordinates) /
P-B (polar coordinates) / mm
Contact lenses are measurable.
Single focal/progressive lens recognition, distance vision detection,
ADD power bar-meter display
Color LCD 320x240 dots 5.7 Type
S, C, A, P, ADD, ADD R/L display, Enlarged SCA display.
Auto R/L function
Easy-to-watch screen with icon display
5-100mm
100-240V~ 50-60VA 1.2A (Auto shut-off in 10 minutes)
197 (W)x220 (D)x404 (H) 3.8kg approx.
* Subject to changes in design and/or specifications, without advanced notice.
WITH PRINTER SPECIFICATION
Printer : Thermal printer, paper width 58mm, Printing additional textbox, AUTO PRINT
OPTIONAL ACCESSORIES
Steel needle marking set (steel needle x3, supply ink, inkpot, holder)
ORDERING CONSUMABLE SUPPLIES AND SPARES
When ordering consumable supplies, please tell the Product name, Part code number, necessary quantity and this Machine type.
Consumables
Product name
Marking ink cartridge
(3 cartridges/set, white)
Lens protection pad
Printer paper
Steel needle marking set
Supply ink
Marking ink cartridge
(3 cartridges/set, red)
52
SPECIFICATIONS
Part code No.
42028 4020
Remark
Standard accessory
42036
44800
42039
42039
42039
Standard accessory
Standard accessory
Optional accessory
Optional accessory
Optional accessory
5500
4001
4010
4001
4030
GENERAL INFORMATION ON USAGE AND
MAINTENANCE
ENVIRONMENTAL CONDITIONS FOR USE
Indoor use Altitude up to 2,000m
Pollution degree II Temperature range: 5-40°C
Maximum relative humidity 80% for temperatures up to 31°C decreasing linearly to 50% relative humidity at 40°C
STORAGE, USAGE PERIOD AND OTHERS
1. Environmental conditions for use
Indoor use Altitude up to 2,000m
Pollution degree II Temperature range: 5-40°C
Maximum relative humidity 80% for temperatures up to 31°C decreasing linearly 50% relative humidity at 40°C
2. When storing the instrument, ensure that the following conditions are met:
(1) The instrument should not be splashed with water.
(2) Store the instrument where air pressure, temperature, moisture, ventilation, sunlight,
dust, salt/sulfurous air, etc. do not give any negative side effect.
(3) Do not store or transport the instrument on a slope or uneven surface or in an area
where it is subject to vibrations or instability.
(4) Do not store the instrument where chemicals are stored or gas is generated.
3. Usage period
8 years from delivery providing regular maintenance is performed (according to the self-certification [TOPCON data]).
SAFETY DESIGNATIONS PER IEC 60601-1 STANDARD
• Type of protection against electric shocks: Class I equipment
Class I equipment does not depend on basic insulation only for protection against electric
shocks. It can also be earthed; therefore, the metal parts with which one comes into contact
do not become conductive if the basic insulation fails.
• Degree of protection against harmful ingress of water: IPx0
CL-300 has no protection against ingress of water. (The degree of protection against harmful
ingress of water defined in IEC 60529 is IPx0)
• Classification according to the method(s) of sterilization or disinfection recommended by the
manufacturer: not applicable.
• Classification according to the degree of safety of application in the presence of a flammable
anaesthetic mixture with air or with oxygen or nitrous oxide: Equipment not suitable for use in
the presence of a flammable anaesthetic mixture with air or with oxygen or nitrous oxide. CL300 should be used in environments where no flammable anesthetics and/or flammable gases
are presents.
• Classification according to the mode of operation: Continuos operation.
Continuos operation is the operation under normal load for an unlimited period, without the
specified limits of temperature being exceeded.
53
GENERAL INFORMATION ON USAGE AND MAINTENANCE
MAINTENANCE AND CHECKS
1. Regularly maintain and check all equipment and parts.
2. When using the instrument after a prolonged period of inactivity, confirm normal and safe
operation beforehand.
3. Take care not mar the cover glass with fingerprints and dirt.
4. When this instrument is not in use, apply the dust cover to it.
5. When the cover glass gets dirty, clean it following the "CLEANING COVER GLASSES" of
the User Manual.
DISPOSAL
Dispose of the instrument according to local disposal and recycling laws.
This symbol is applicable for EU member countries only.
To avoid potential negative consequences for the environment and possibly human
health, this instrument should be disposed of (i) for EU member countries - in
accordance with WEEE (Directive on Waste Electrical and Electronic Equipment),
or (ii) for all other countries, in accordance with local disposal and recycling laws.
INTENDED USER PROFILE
This lensmeter is an electric instrument and it must be used in accordance with its Instruction
Manual.
54
GENERAL INFORMATION ON USAGE AND MAINTENANCE
ELECTROMAGNETIC COMPATIBILITY
This product conforms to the EMC Standard (IEC 60601-1-2 Ed.3.0 : 2007).
a) MEDICAL ELECTRICAL EQUIPMENT needs special precautions regarding EMC and needs to
be installed and put into service according to the EMC information provided in the ACCOMPANYING DOCUMENTS.
b) Portable and mobile RF communications equipment can affect MEDICAL ELECTRICAL
EQUIPMENT.
c) The use of ACCESSORIES, transducers and cables other than those specified, with the
exception of transducers and cables sold by the manufacturer of the EQUIPMENT or SYSTEM
as replacement parts for internal components, may result in increased EMISSIONS or
decreased IMMUNITY of the EQUIPMENT or SYSTEM.
d) The EQUIPMENT or SYSTEM should not be used adjacent to or stacked with other equipment.
IF adjacent or stacked use is necessary, the EQUIPMENT or SYSTEM should be observed to
verify normal operation in the configuration in which it will be used.
e) The use of the ACCESSORY, transducer or cable with EQUIPMENT and SYSTEMS other than
those specified may result in increased EMISSION or decreased IMMUNITY of the EQUIPMENT or SYSTEM.
Item
RS-232C cross cable
Article code
Model No.
Length (m)
418120002
-
4.9
-
-
5.1
LAN CABLE
Guidance and manufacturer's declaration - electromagnetic emissions
The CL-300 is intended for use in the electromagnetic environment specified below.
The customer or the user of the CL-300 should assure that it is used in such an environment.
Compliance
Electromagnetic environment - guidance
RF emissions
CISPR 11
Emissions test
Group 1
The CL-300 uses RF energy only for its internal
function. Therefore, its RF emissions are very low
and are not likely to cause any interference in
nearby electronic equipment.
RF emissions
CISPR 11
Class B
The CL-300 is suitable for use in all establishments other than domestic and those directly connected to the public low-voltage power supply
network that supplies buildings used for domestic
purposes.
Harmonic emissions
IEC61000-3-2
Complies
Voltage fluctuations/
flicker emissions
IEC61000-3-3
Complies
55
GENERAL INFORMATION ON USAGE AND MAINTENANCE
Guidance and manufacturer's declaration - electromagnetic immunity
The CL-300 is intended for use in the electromagnetic environment specified below.
The customer or the user of the CL-300 should assure that it is used in such an environment.
Immunity test
IEC 60601
Compliance
Electromagnetic environment test level
level
guidance
Electrostatic
±6 kV contact
±6 kV contact
Floors should be wood, concrete
discharge (ESD)
or ceramic tile. If floors are covIEC 61000-4-2
±8 kV air
±8 kV air
ered with synthetic material, the
relative humidity should be at
least 30%.
Electrical fast
±2 kV for power
±2 kV for power
Mains power quality should be
transient/burst
supply lines
supply lines
that of a typical commercial or
IEC 61000-4-4
hospital environment.
±1 kV for
±1 kV for
input/output lines input/output lines
Mains power quality should be
±1 kV
Surge
±1 kV
IEC 61000-4-5
differential mode differential mode that of a typical commercial or
hospital environment.
±2 kV
±2 kV
common mode
common mode
Voltage dips, short <5% Ut
<5% Ut
Mains power quality should be
interruptions and
that of a typical commercial or
(>95% dip in Ut)
(>95% dip in Ut)
Voltage variations
hospital environment. If the user
for 0.5 cycle
for 0.5 cycle
on power supply
or the CL-300 requires continued
40% Ut
40% Ut
input lines
operation during power mains
(60% dip in Ut)
(60% dip in Ut)
IEC 61000-4-11
interruptions, it is recommended
for 5 cycles
for 5 cycles
that the CL-300 be powered from
70% Ut
70% Ut
an uninterruptible power supply
(30% dip in Ut)
(30% dip in Ut)
or battery.
for 25 cycles
for 25 cycles
<5% Ut
<5% Ut
(>95% dip in Ut)
(>95% dip in Ut)
for 5 sec.
for 5 sec.
3 A/m
3 A/m
Power frequency magnetic fields
Power frequency
should be at levels characteristic
(50/60 Hz)
of a typical location in a typical
magnetic field
commercial or hospital environIEC 61000-4-8
ment.
NOTE Ut is the a.c. mains voltage prior to application of the test level.
56
GENERAL INFORMATION ON USAGE AND MAINTENANCE
Guidance and manufacturer's declaration - electromagnetic immunity
The CL-300 is intended for use in the electromagnetic environment specified below.
The customer or the user of the CL-300 should assure that it is used in such an environment.
Immunity test
IEC 60601
test level
Compliance
level
Electromagnetic environmentguidance
Portable and mobile RF communications equipment should be used no
closer to any part of the CL-300,
including cables, than the recommended separation distance calculated from the equation applicable to
the frequency of the transmitter.
Recommended separation distance
Conducted RF
IEC 61000-4-6
3 Vrms
150kHz to 80MHz
Radiated RF
IEC 61000-4-3
3 V/m
80MHz to 2.5GHz
d = 1.2 P
3V
3 V/m
d = 1.2 P 80MHz to 800MHz
d = 2.3 P 800MHz to 2.5GHz
wh er e P i s the ma xi mum o utpu t
power rating of the transmitter in watts
(W) according to the transmitter manufacturer and d is the recommended
separation distance in meters (m).
Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey, a should be less
than the compliance level in each frequency range. b
Interference may occur in the vicinity
of equipment marked with the following symbol:
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is
affected by absorption and reflection from structures, objects and people.
a
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and
land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted
theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an
electromagnetic site survey should be considered. If the measured field strength in the location in which
the CL-300 is used exceeds the applicable RF compliance level above, the CL-300 should be observed
to verify normal operation. If abnormal performance is observed, additional measures may be necessary,
such as reorienting or relocating the CL-300.
b
Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
57
GENERAL INFORMATION ON USAGE AND MAINTENANCE
Recommended separation distance between portable and mobile RF
communications equipment and the CL-300
The CL-300 is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the CL-300 can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF
communications equipment (transmitters) and the CL-300 as recommended below, according
to the maximum output power of the communications equipment.
Rated maximum
output power of
transmitter
W
Separation distance according to frequency of transmitter
m
150kHz to 80MHz
80MHz to 800MHz
800MHz to 2.5GHz
d = 1.2 P
d = 1.2 P
d = 2.3 P
0.01
0.12
0.12
0.23
0.1
0.38
0.38
0.73
1
1.2
1.2
2.3
10
3.8
3.8
7.3
100
12
12
23
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in metres (m) can be estimated using the equation applicable to the frequency of
the transmitter, where P is the maximum output power rating of the transmitter in watts (W)
according to the transmitter manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range
applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is
affected by absorption and reflection from structures, objects and people.
58
GENERAL INFORMATION ON USAGE AND MAINTENANCE
SHAPE OF PLUG
Country
Voltage/frequency
Shape of plug
Mexico
110V/50Hz
Type C&E
Argentina
220V/60Hz
Type A
Peru
220V/60Hz
Type A
Venezuela
110V/50Hz
Type C&E
Bolivia & Paraguay
220V/60Hz
Type A (Most common)
Type H (infrequently)
Chile
220V/60Hz
Type A
Colombia
110V/50Hz
Type C
Brazil
220V/60Hz
127V/60Hz
Type A
Type C
Ecuador
110V/50Hz
Type C&E
USA
120V/60Hz
Type A (Hospital Grade)
Canada
120V/60Hz
Type A (Hospital Grade)
59
GENERAL INFORMATION ON USAGE AND MAINTENANCE
USING THE INSTRUMENT AS A SYSTEM
This product can perform data transfer with other devices.
For connectable devices and conditions for connection, ask your dealer/service engineer.
ON - LINE SYSTEM
The data of computerized lensmeter can be transferred to the instruments through RS232C interface, and also measuring data of the instruments can be transferred to computerized visiontester.
CL
CV
Computer
CONNECTING EXTERNAL I/O TERMINALS
When connecting this product with a commercial personal computer, use one conforming to IEC60950-1, with a separation unit.
60
USING THE INSTRUMENT AS A SYSTEM
When calling please give us the following information about
your unit:
• Machine type: CL-300
• Manufacturing No. (Shown on the rating plate on the back
of the instrument)
• Period of Usage (Please give us the date of purchase).
• Description of Problem (as detailed as possible).
COMPUTERIZED LENSMETER CL-300
USER MANUAL
Version of 2012 (2012.02-100LW0)
Date of issue: 15, February, 2012
Published by TOPCON CORPORATION
75-1 Hasunuma-cho, Itabashi-ku, Tokyo, 174-8580 Japan.
©2012 TOPCON CORPORATION
ALL RIGHTS RESERVED
BACK COVER
COMPUTERIZED LENSMETER
CL-300
42028 90050
Printed in Japan 2012.02-100LW0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement