Waldso Desktop Attendance Machine User Manual
Below you will find brief information for Desktop Attendance Machine. This device allows for the enrollment and identification of users using fingerprints, passwords, ID cards, or Mifare cards. You can set attendance rules, query attendance records, and print reports. This device is ideal for businesses looking to automate their time and attendance tracking.
Advertisement
Advertisement
Desktopstyled Attendance Machine
User Manual
Ver 1.0
Desktopstyled Attendance Machine
User Manual V1.0
Contents
2.6 Authentications of fingerprint, password and card. ................................. 15
I
Desktopstyled Attendance Machine
User Manual V1.0
1. Before use
Read through this manual before operating this machine.
Must know
Firstly installing fingerprint machine well, then the fingerprint enrollment and identification will be taken.
Installation Enrollment Identification
Enrollment Installation Identification
Enroll a finger
Use the index finger, middle finger or ring finger, but not the thumb and little finger (because they are usually clumsy when pushing on the sensor window). How to place the finger:
1) The correct way:
Place a finger flatware on the sensor surface
Place it to the center of the sensor surface
1
Desktopstyled Attendance Machine
User Manual V1.0
2) The wrong ways:
Components
Component name
Quantity
USB cable
1
Switch power Universal Adaptor plug Backup battery
1 1 1
About Use
The recommended steps:
Step 1: install the machine completely and power on.
Step 2: enroll the administrator and users. That is to enroll fingerprints, passwords, ID or Mifare cards.
Step 3: user identification. Confirm whether the enrolled fingerprints,
2
Desktopstyled Attendance Machine
User Manual V1.0 passwords, ID or Mifare cards are available.
Step 4: user attendance
Step 5: connect with PC and use the corresponding attendance software to download data, assign departments, and arrange shifts etc.
Step 6: set attendance rules, query attendances and print reports in attendance software.
Introduction
The product is developed for practical function and easy use. It uses the keypad to realize functions. Since its convenient operations, fashionable performance, desktopseated design, lightweight and flexibility, it is really a good choice for user attendance.
Panel:
LED LCD Fingerprint Sensor
Keypad
3
Speaker
Desktopstyled Attendance Machine
User Manual V1.0
LED indicator: it displays green during normal work, and it displays red when the authentication is failed.
Keypad: It includes the digit keys, power key, ESC key, OK key, and six function keys of Enroll FP, PW/Card, Del User, Time Set, IN, OUT.
As below shown:
Enroll FP:
Enroll fingerprint
PW/Card:
Enroll password, ID or Mifare cards
TimeSet:
Set device time and fixedtime of bell to ring
Digit keys
Del User:
Delete users
OUT:
‘CheckOut’ status and ‘down’ key
Power Exit
IN:
‘Checkin’ status and ‘up’ key
OK
Original window
After power on, the original window is as below shown:
Or ‘CheckOut’
CheckIn
10:12
090811 TUE
4
Desktopstyled Attendance Machine
User Manual V1.0
2. Enrollment and Identification
For the first time to use the device, no administrator at this moment, press the function key to enroll the administrator and users. Only one administrator can be enrolled in the system, the number is 8888. Firstly enrolling the administrator is recommended. If the administrator is enrolled in the device, only users can be enrolled.
If there is no administrator, users can be enrolled by anyone. If there is an enrolled administrator, users can’t be enrolled until passing the administration identification.
Three enrollment modes of fingerprint, password, Mifare card are applied to three people groups with different fingerprint quality individually. Fingerprint enrollment is applied to the people group with good fingerprint quality, and most people are in this group. Fingerprint enrollment as well as password enrollment is applied to the people group who can enroll easily but authenticate difficultly, and a small part of people are in this group. Password enrollment is applied to the people group who can’t enroll fingerprints successfully, and about 1% of people are in this group, maybe a little change in the actual use.
Before enrolling users, if there is an enrolled administrator, you must authenticate the administrator status, Firstly press ‘Enroll’ key, then the device displays ‘Administrator affirm’, at last press the fingerprint or password of administrator to authenticate.
Note: if no administrator is enrolled, you don’t need the administrator authentication.
5
Desktopstyled Attendance Machine
User Manual V1.0
2.1 Fingerprint Enrollment
1) In the original window, press ‘Enroll FP’ key to pop up the window as follows:
Enroll FP
New Enroll?
ESC OK
2)Press OK key to continue to display the window as follows:
Note: The ID number is 5 bits. If your ID number is less than 5 bits, system will add 0 at the front of the digit automatically. For example: the ID number is 1, the machine will display it as 00001.
New Enroll
User ID: 00001
ESC OK
3) In ‘User ID’ column, input the number you want to enroll (the number is from 165534) and press ‘OK’ key to confirm, then the screen will inform ‘Place finger …’ as follows:
Note: If the User ID is 8888, you will enroll the only administrator.
New Enroll
000010
Place Finger……
ESC/Exit
4) After pressing the fingerprint for three times, system will enter into the following window automatically. The fingerprint is enrolled successfully. In this window, press ‘OK’ key to enroll new users, or
6
Desktopstyled Attendance Machine
User Manual V1.0 press ‘ESC’ key to enroll backup fingerprints of just enrolled user.
New Enroll
000010
ESC OK (Save)
5) In step 4), if press ‘OK’ key, you can continue to enroll new users by referring to step 1)4) in the windows as follows:
New Enroll
Continue?
ESC OK
6) In step 4) 5), if press ‘ESC’ key, you will start to enroll the backup fingerprints by referring to step 1)4) in the window as follows. You can enroll nine backup fingerprints of the same user at most.
Backup Enroll
Continue?
User ID 00001
ESC OK
7) During the enrollment, you can press ‘ESC’ key one time or continually to exit and return to the original window.
7
Desktopstyled Attendance Machine
User Manual V1.0
2.2 Password Enrollment
1) Press ‘PW/Card’ key to enter into the menu. There are three situations here. (No card, ID card, Mifare card). a. No card: enter into the enrollment window directly.
New Enroll
User ID 00003
ESC OK b. ID card (optional): select Enroll Pwd and press OK key.
Menu
Enroll Pwd
Reg RF ID c. Mifare card (optional): select Enroll Pwd and press OK key.
Menu
Enroll Pwd
FPCard Mng
2) In User ID column, input the number that you want to enroll (the number is from 165534), and press ‘OK’ key to confirm.
New Enroll
User ID 00003
ESC OK
8
Desktopstyled Attendance Machine
User Manual V1.0
3) In Input Pwd column, input the password (5 bits) and press ‘OK’ key.
New Enroll
Input Pwd *****
ESC OK
4) Input the password again, if two passwords are not in the same, system will inform you to input the password again.
New Enroll
Input Pwd *****
Pwd Affirm *****
5) If they are in the same, you will enter into the following window automatically. The password is enrolled successfully. Press ‘OK’ key to continue enrolling the password of new user, or press ‘ESC’ key to change the password of just enrolled user.
Note: the letter ‘P’ in 00003P indicates the password.
New Enroll
00003P
ESC OK(Save)
6) In step 5), if press ‘OK’ key, you will start to enroll a new user by referring to step 2)5) in the window as follows:
New Enroll
Continue?
ESC OK(Save)
9
Desktopstyled Attendance Machine
User Manual V1.0
7) In step 5), if press ‘ESC’ key, you will start to change the password by referring to step 2)5) in the window as follows:
Chg Password
Continue?
ESC OK(Save)
8) During the enrollment, you can press ‘ESC’ key one time or continually to exit and return to the original window.
2.3 ID card enrollment★
1) Press ‘PW/Card’ to enter into the window as follows:
Menu
Enroll Pwd
Reg RF ID
2) Press ‘IN5’ or ‘OUT6’ to select Reg RF ID and press ‘OK’ key to enter into the window as follows:
Reg RF ID
New Enroll?
ESC OK
3) Press ‘OK’ key to continue.
10
Desktopstyled Attendance Machine
User Manual V1.0
New Enroll
User ID: 00006
ESC OK
4) In User ID column, input the number that you want to enroll (the number is from 165534) and press ‘OK’ key.
New Enroll
Show the card
User ID: 00006
ESC OK
5) Show the card according to the prompt. After reading the card number, the displayed information is as follows:
New Enroll
Card:16650449
User ID: 00006
ESC OK
6) Press ‘OK’ key to enter into the following window. The card is enrolled successfully. In this window, press ‘OK’ key to continue enrolling new cards, or press ‘ESC’ key to enter into the change ID card window.
Note: the letter ‘C’ in 00006C indicates the ID card.
New Enroll
00006C
ESC OK(Save)
11
Desktopstyled Attendance Machine
User Manual V1.0
7) In step 5), if press ‘OK’ key, you can continue to enroll new cards by referring to step 2)6) in the window as follows.
New Enroll
Continue?
ESC OK
8) In step 5), if press ‘ESC’ key, you can change the just enrolled card by referring to step 4)6) in the window as follows.
Chge ID Card
Continue?
ESC OK
9) During the enrollment, you can press ‘ESC’ key once or continually to exit and return to the original window.
Note: ID card is the optional function. If the ID card function is wanted, please consult our commercial representatives or presale technicians. If more information is wanted, please refer to <<User
Guide of ID card>>.
2.4 Mifare card enrollment★
1. In the original window, press ‘PW/Card’ key to enter into the following window.
Menu
Enroll Pwd
FPCard Mng
12
Desktopstyled Attendance Machine
User Manual V1.0
2. Press ‘OUT6’ key to select ‘FPCard Mng’ and press ‘OK’ key to enter into the following window. Press ‘IN5’ or ‘OUT6’ key to move the cursor up or down.
.
FPCard Mng
Create PINCard
Enroll FPCard
Create FPCard
Reg FPCard
Unreg FPcard
Empty FPCard
Dump FPCard
Move To FPCard
Card Only Y
Create PINCard: Create the number card of enrolled user in the fingerprint machine. User can use ‘card’ to check attendance and doesn’t need to press the fingerprint.
Enroll FPCard: Store the enrolled fingerprint into the card, at this time the fingerprint is saved into the card directly but not saved in the device.
Users can use ‘Card+Fingerprint’ to authenticate the status, that is, firstly show the card and then press the fingerprint.
Create FPCard: Copy the enrolled fingerprint (fingerprint in device) to the card. User can use the fingerprint to authenticate the status and can also use ‘Card+Fingerprint’ to authenticate the status.
Reg FPCard: Before using the fingerprint card of one fingerprint machine in another fingerprint machine, you must register the fingerprint card in this machine.
Unreg FPCard: In order to forbid the card to be used in some machine, you should unregister the fingerprint card in this machine.
Empty FPCard: Empty all information (fingerprint, number) in the
13
Desktopstyled Attendance Machine
User Manual V1.0 fingerprint card.
Dump FPCard: Copy the fingerprint in card into fingerprint machine.
After copying, you can use the fingerprint to authenticate.
Move To FPCard: Move the fingerprint in fingerprint machine into the fingerprint card, then the fingerprint is only saved in card and not in fingerprint machine any more.
Card only: If select ‘Yes’ here, you can pass the authentication by only authenticating the number card. If select ‘No’ here, you still need to authenticate the fingerprint after authenticating the card.
Note: Mifare card is the optional function. If the Mifare card function is wanted, please consult our commercial representatives or presale technicians. If more information is wanted, please refer to
<<User Guide of Mifare card>>.
2.5 Delete a user
Delete the enrolled users in system.
In the original window, press ‘Del User’ key to pop up the following window. In User ID column, input the number that you want to delete, then press ‘OK’ key to delete it from the device.
Del User
User ID 00001
ESC OK
After deleting, the next user ID is displayed in the window. You can press ‘OK’ key to continue deleting, or press ‘ESC’ key to exit.
14
Desktopstyled Attendance Machine
User Manual V1.0
2.6 Authentications of fingerprint, password and card.
Users can save attendance records in machine through fingerprint or password authentications.
Ø Fingerprint attendance
(1) 1:1 fingerprint verification (ID + fingerprint)
Verify the current fingerprint pressed on sensor with the corresponding
ID number of user inputted by keypad
Step 1: input the user ID that you want to verify in original window.
Step 2: press the fingerprint on the sensor correctly.
Step 3: if device informs ‘thanks’, it means a successful enrollment. If device informs ‘please try again’, return to step 1 to reoperate.
(2) 1: N fingerprint identification
Identify the pressed fingerprint with all fingerprints in device.
Step 1: press the fingerprint on the sensor correctly.
Step 2: if device informs ‘Thanks’, it means a successful identification.
If device informs ‘please try again’, return to step 1 to reoperate.
Ø Password attendance
Step 1: input the ID number of user you want to verify in original window and press ‘OK’ key.
Step 2: input the password.
Step 3: if device informs ‘thanks’, it means a successful verification. If device informs ‘error password’, return to step 1 to reoperate.
Ø Mifare card attendance
15
Desktopstyled Attendance Machine
User Manual V1.0
If use ‘Create PINCard’ to enroll the Mifare card, firstly press
‘PW/Card’ key to enter into Menu, secondly select FPCard Mng and press ‘OK’ key, thirdly select the Card Only item. There are two situations here.
(1) If select ‘Y’ in Card Only item:
In the original window, place the number card over the sensor area (the distance should be short, otherwise system can’t sense the card). Display the window as follows:
Verify
User ID 00001
Verified
Note: If use the other method to enroll the Mifare card (For example:
Enroll fingerprint card) and select ‘Y’ in card only item, you will find that the authentication is as same as the above.
(2) If select ‘N’ in Card Only item:
In the original window, place the number card over the sense area (the distance should be short, otherwise system can’t sense the card). Display the widow as follows:
FP Verify
User ID: 00002
Place finger…
After pressing the fingerprint, display the window as follows:
1:N FP Match
Remove Finger
16
Desktopstyled Attendance Machine
User Manual V1.0
About 0.5 second later, if a successful authentication, the device will issue a voice of ‘Thanks’ and display the window as follows:
Verify
User ID: 00002
Verified
If a failed authentication, system will inform you to place finger again.
If no operation in 0.5 second, system will return to the original window.
Ø ID card attendance
If the ID card is enrolled in the device already, you can pass the authentication by punching the card in the sense area.
17
Desktopstyled Attendance Machine
User Manual V1.0
3. Other functions
3.1 Time Setting
In the original window, press ‘TimeSet’ key to enter into the time setting window.
Scheduled 00:00
2009730
ESC
9:38:55
OK
Press up or down key (IN or OUT key) to move the cursor to the different position, and then change the corresponding time.
When the cursor is located in Scheduled, you can set the time for the bell to ring. Then the bell will ring at the fixedtime 00.00. If the cursor in located in Scheduled, you can press ‘Del User’ to change the time as ‘: ’, that is to close the fixedtime bell.
After setting, press ‘OK’ key to save the time and exit from the time setting window with prompt voice ‘Thanks’
3.2 Power Management
The device is equipped with power with USB connector and backup battery. When use power adapter with USB connector to supply power, the backup battery is charged at the same time and the charging time shouldn’t be less than 8 hours. When the power is off or unable to be powered by power with USB connector, the device will be powered by backup battery automatically and the saturated backup battery can supply power to device for 3 hours.
18
Desktopstyled Attendance Machine
User Manual V1.0
There is an electricity icon at the upright corner of LCD, which is convenient for users to view the status and the electricity of backup battery. When the device is only powered by the backup battery, the icon indicates the battery electricity; when the device uses the power adapter and the backup battery at the same time, the icon indicates the charging status and electricity of backup battery; when the device is powered by the power adapter, no icon is displayed.
When the battery electricity is displayed as 0 grid, the battery icon flashes and the buzzer will buzz to alarm per a second for five minutes.
3.3 Attendance Status
During checking attendance, if you want to check in, firstly press ‘IN’ key to display ‘CheckIN’ on the screen, then press fingerprint or password to authenticate. If you want to check out, firstly press ‘OUT’ key to display ‘CheckOut’ on the screen, then press fingerprint or password to authenticate.
3.4 Test Automatically
In the original window, press ‘6’ digital key for four times, and then press ‘TimeSet’ key to display as follows:
Flash Test
Pls Keep Pwr ON
Continue?
ESC OK
Press OK key to start testing. The testing order is Flash, LCD, Voice, fingerprint reader, Key, RTC. During testing especially flash testing,
19
Desktopstyled Attendance Machine
User Manual V1.0 please guarantee the stability of power, otherwise the hardware of system maybe be damaged.
4. Attendance Management
This device is to record attendance time, and the attendance software is to deal with report statistics. The device can be connected with PC directly through USB cable. The way to operation the attendance software, please refer to <<Management System Explanation>>.
20

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Fingerprint, password, ID card, and Mifare card authentication
- Attendance record management
- Time setting
- Power management
- Automatic testing
- USB connectivity for data download and software management