USER MANUAL HDMI Over Ethernet 1、Introduction 2

USER MANUAL HDMI Over Ethernet 1、Introduction 2
USER MANUAL
HDMI Over Ethernet
1、Introduction
2、Specifications
3、Package Contents
4、Panel Descriptions
5、 Connection and operation
6、 Application diagram
1、Introduction
HDMI Over Ethernet is based on TCP/IP standard. It transmit your HD display
with the high resolutions up to 395 feet (120 meters) away from your HDMI or DVI-D
source by using one CAT5e/6 cable. With the advantage of TCP/IP standard,you can
extend your HD video to multiple displays by using an Ethernet Switch.
2 、Specifications
1. Following TCP/IP standard.
2. Support HDMI1.3 protocol.
3. HDCP1.1 & 1.2 protocol compliant
4. Support point-to-point mode, one point-to-many mode and cascade connection
mode.
5. Support IR extender function allows IR remote control of Source devices from
remote viewing location by sending IR commands received in the vicinity of the
Display back to the Source devices.
HDTV Resolutions
480p,576p,720p,1080p
Audio Sample rate
32kHz, 44.1kHz and 48kHz
IR remote control
38KHz; NEC
HDMI
HDMI 1.3
HDCP
HDCP 1.2
Power adapter
Input: 100V - 240V (50 - 60Hz)
Output: 5V/1A
Power consumption
HDMI Sender: 3W
3W
Size(L-W-H)
100×60×25mm
HDMI Receiver:
Weight
128g*2PCS
Operating
0 - 70 Degree Celsius / 10% - 80%RH
Temperature/Humidity
(no condensation)
Storage
-10 - 80 Degree Celsius / 5% -90%
Temperature/Humidity
RH(no condensation)
3. PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and make sure the
following items are contained in the shipping carton:
1) Main unit No. 1 Sender , Main unit No. 2 Receiver
2) Two pieces of 5V DC Power Supply.
3) a pieces of IR transmitter and a pieces of IR receiver
4) User’s Manual
4、 Panel Descriptions
HDMI Sender
5V/1A
Supply power for the Sender
RESET
Hold down the key for 10 seconds, the model will Restore the
default setting
IR-OUT
Connect IR transmitter to this Port.
HDMI - IN
Connect HDMI Source to this Port.
STATUS
When system start up, the Green LED will be on,When transmit
video, the led will blink.
Power
Power on, The Red led is on
HDMI Receiver
5V/1A
Supply power for the Receiver
RESET
Hold down the key for 10 seconds, the model will Restore the
default setting
IR-IN
Connect IR receiver to this Port.
HDMI - Out Connect HDMI sink device to this Port.
STATUS
When system start up, the Green LED will be on,When transmit
video, the led will blink.
Power
Power on, The Red led is on
5、Connection and operation
1) Connect the HDMI source (such as DVD, PS3, STB ) to the HDMI IN of Sender.
2) Connect the IR sender to the Sender IR OUT Port, and Be Directed at HDMI video
source’s IR receiver.
3) Connect the HDMI out of Receiver to HDTV display.
4) Connect the IR receiver to the Receiver IR IN Port.
5) Use one Cat5e/6 cable up to 120m to connect the Sender and Receiver.
6) Plug two pieces of 5V power supply into the Sender and Receiver.
7) Power on the HDTV display and HDMI source.
6、Application diagram
Application 1
Application 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement