Manual - EasternCCTV
Advanced Digital Fingerprint Lock
= Fingerprint Lock
Manual
Fingerprint Securily Door Locks User's Manual
Tr Copyright Note
All contents of this Manual, including texts and images related to the door locks products
and the micro-computer programs, are copyright of our company, and any imitation and copy is
an act of tort,
vr Upgrade Description
As the continuous improvement and development of technology, our company will
continuously upgrade the product functions to meet the market demand. Any difference
between the purchased product and the Manual is subject to change without notice, In box of
doubt, please contact directly with our company for the latest product information.
Fingerprint Security Door Locks User's Manual
Table of Contents
CHAPTER 1 OPERATING INSTRUCTION
1.1 FACTORY DEFAULT 4
1.2 REGISTER THE ADMINISTRATOR PASSWORD 4
1.3 ADD COMMON USERS FINGERPRINTS OF NUMBER 10 TO 49 5
1.4 DELETE A FINGERPRINT 7
1.5 OPERATION INSTRUCTION FOR MECHANICAL KEY B
1.6 NOTES FOR USE 6
CHAFTER 2 INSTALLATION INSTRUCTION 10
3 INSTALLATION [INSTRUCTION 10
2.2 INSTALLATION REQUIREMENTS 10
2.2.1 Left & right hand door 1
22.2 Installation conditions HH
33.3 Hole dimensions H
2.3 TOOLS OF INSTALLATION 13
2.4 INSTALLATION 14
2.4.1 Installation p } H
2.4.2 Notes for installation 19
2.5 ADDITIONAL ATTENTICMS 19
CHAPTER 3 EXCEPTION HANDLING 20
BATTERY REPLACEMENT 20
Y MECHANICAL KEYS 20
CHAPTER 4 MAINTENANCE 21
vr LOCK SURFACE CLEANING 21
wr OIL TIE LOCK 21
YX REPLACE THE LOCK FACT AND HANDLE 21
APPENDIX 1: PACKTNG LIST 1
APPENDIX 3: WARRANTY CARD 22
AFTER-SALE SERVICES 7
Fingerprint Security Door Locks User's Manual
Chapter 1 Operating Instruction
The fingerprint lock can store 100 fingerprints, of which the No 00 is the fingerprint of
administrator, No 01 — 09 are fingerprints of super users, and the fingerprints of No 10 — 99 are
of normal users. The fingerprint of No. 00 is authorized to add/remove the fingerprints of No 01
- 99, and the super fingerprints of No. 01 — 09 are authorized to add/remove the fingerprints of
No 10 — 99, There are four keys on the exterior lock face, namely, key 0, 1, 2 and 3 as shown in
the following figures.
EEES
Fingerprini — aoquisition
а . Digital display sercen
window
Key 3; Fower on/coafirm
Key E: ESC
Cover of lack
Kay 0: acc Pape up
| Key 1: Deleto'Page down |
Lulenor kck sel
Series sketch map of exterior lock set
Key 0——add/page up
Key |——delete /page down
Key 2— Esc
Key 3—— Power up/confirm
|
a A a a алое a
Eo наденет .
ko.
Series sketch map of interior lock set
Interior Jack sel
| Ky constant open |
Fingerprint Security Door Locks User's Manual
1.1 Factory default
The factory fingerprint database is empty and the default user password is 000000. Enter the
default password to unlock the door.
1.2 Register the administrator password
1.2.1 Register of administrator password: (change the administrator password)
|: Remove any battery, and hold down the 0 key and then reinstall the removed battery.
After a long “Beep” and “0” appears on the display, then enter the state of password setting.
2: Release key 0 and press key 0 or | again to select the password to be set, and input a
six numeric password.
3: The roles of each key when input the administrator password:
2:07” key, input numbers and page-up from 0.
b:“1” key, input numbers and page-down from 0.
c:7” key, exit from inputting password
d:*3" key, confirm the current password
4: The 2-digit numbers on the display when input password: units digit is the password
to be entered currently and the tens digit is the password confirmed for the previous time, and
key 3 should be pressed after deciding a single digit. After the six available digits are input,
there will be a long “Beep” and the green light on the display will be on. Repeat the 6-digit
password just entered. The system will automatically exit and save the password as the
administrator password.
5: If another effective 6-numeric password is entered by the above mentioned method,
the system will cover the former password and save the last one as an available password.
1.2.2 Register the administrator fingerprint (fingerprint of No 00)
|: Remove any battery, and hold down key |, and reinstall the battery just removed. A
long “Beep” can be heard and the red light on the Fingerprint acquisition window is on after a
flicker.
2: Release key 1 and enter the state of collecting administrators fingerprint.
3: Administrator should put a finger on the acquisition window for fingerprint
acquisition (don’t press any key). After hearing the first long “Beep”, move the finger away,
and put the finger on it again after 0.5 second. And there will be the second “Beep” and the
green light will be on, “00” will appear on the display screen. That means the acquisition of
administrator's fingerprint is successful. The system will automatically exit and save the
administrator fingerprint.
4: If another fingerprint is collected in the mentioned way, the system will cover the
former fingerprint and save the last one as the administrator fingerprint.
5: The fingerprint set as the administrators fingerprint can’t be set as super fingerprint
or common fingerprint anymore.
1.2.3 Add Super fingerprint with the administrator fingerprint: (the 9 fingerprints from
01 to 09 are super fingerprints)
|: Press key 3, the red light on the acquisition window will bc on after a flicker, put in
the administrator fingerprint for confirmation within 3 seconds.
Fingerprint Security Door Locks User's Manual
2: After the successful verification, there will be a long “Beep” and the No “00”,
which stands for the administrator, in the display. And the green light will flick to show the
successful verification for administrator 1D.
3: Press key O within five seconds and there will be a “Beep”, and the number “01”
will flicker on the display screen (it may also be 02, 03, etc according to the number of
fingerprint saved in the lock), and the green light will be on. Press key 3 to confirm the
current serial number of fingerprint. The red light is on after a flicker, and the lock enters the
state of super fingerprint acquisition.
4: Put the finger to be registered on the acquisition window for acquisition. (Don’t
press any key at this time), and there will be a long tone of “Beep” during acquisition, and put
the finger on it again after 0.5 second. And there will bc the second “Beep” in | second and
the green light will be on, then “01” will appear on the display screen. That means the
acquisition of super fingerprint No 1 is successful. The system will then exit and save the
administrator fingerprint automatically.
5: The same fingerprint that has been set as the super fingerprint can’t be set as
common user fingerprint anymore.
1.3 Add common users fingerprints of number 10 to 99
1.3.1 Add common user fingerprint with super fingerprint user
1: Press key 3 directly, the red light on the acquisition window is on after a flicker, and
verification of super fingerprint will be started within 5 seconds.
2: When the verification 13 succeeded, there will be a long “Beep” and the super
fingerprint number “01 will flicker on the display screen. After successful verification of
super fingerprint ID, the super fingerprint user is allowed to add common fingerprint user (If
the numbers of super fingerprints are 02 and 03, 02 and 03 will be displayed on the screen).
3: Press key 0 within five seconds and there will be a long “Beep”, and the number “10”
will flicker on the display screen, and the green light will be on. Press key 3 to confirm the
current number of fingerprint. The red indicator lamp will be on after a flicker, and the lock
enters the state of fingerprint acquisition of common users.
4: Put the finger to be registered on the acquisition window for acquisition. (Don’t press
any key at this time), and there will be a long tone of “Beep” during acquisition, and put the
finger on it again after 0.5 second. And there will be the second “Beep” in 1 second and the
green light will be on, then “10” will appear on the display screen. That means the
acquisition of super fingerprint No 10 is successful. The system will then exit and save the
administrator fingerprint automatically.
5: The fingerprint that has been set as the common user fingerprint can’t be sel as super
fingerprint anymore.
Remark: © Bcfore verify the number of fingerprint, you can press key D'or | to choose other
fingerprint numbers: any unregistered number between 10 and 99 can be chosen.
(@The fingerprint that has been set as the super fingerprint can’t be set as common
user fingerprint anymore. If the number of a fingerprint is found to be registered, the
system will prompt and then exit.
(@Common users’ fingerprint can also be added by the administrator fingerprint: press
key 0 or } to select other number: super users will be added if choosing a number
between 01 and 09; and common users will be added i choosing a number between
Fingerprint Security Door Locks User's Manual
10 and 99.
1.3.2 Add a user of fingerprint with administrator password
l: Press key O or | to select the password and press key 3 to confirm, and there will be
a long “Beep” and green light will be on after verifying the correct 6-digit administrator
password, which means the successful password verification.
2: Press O within 5 seconds, and there will be a long “Beep”, “02” will flicker on the
display screen, the green light will be on, and press key 3 to confirm the number of
fingerprint to be registered; the red light on the fingerprint acquisition window will be on
after a flicker.
3: The new user should put the finger on the acquisition window in 5 scconds. (Don’t
press any key at this time), and there will be a long tonc of “Beep” during acquisition, and put
the finger on it again after 0.5 second. And there will be the second “Beep” in | second and
the green light will be on, then “02” will appear on the display screen. That means the
acquisition of super fingerprint No 02 is successful. The system will then exit and save the
administrator fingerprint automatically.
4: If the acquisition fails, there will be two short “Beep” and “- -” will appear on the
display and the red light for alarm will be on. Then the system will exit automatically.
5: Before verify the number of a fingerprint, you can press key 0 or 1 to choose other
fingerprint numbers: super users will be added if choosing a number between 01 and 09; and
common users will be added if choosing a number between 10 and 99.
1.3.3 Normal use of the fingerprint lock
l: Press key 3, the red light will be on after a flicker, and to start the state of scanning
preparation.
2: Press the registered fingerprint on the window within 5 seconds to carry out
fingerprint acquisition.
3: After a successful verification, there will be long “Beep”. the registration No. of the
user will appear on the display screen and the green light will be on. Open the door with the
front handle within 5 seconds.
4: The system will exit after 5 seconds and return to the state of being locked.
5: If the acquisition fails, there will be two short “Beep”, “- -” will appear on the
display meanwhile the red light for alarm will be on. The system will exit automatically.
6: If, for any reason, the system can’t recognize a fingerprint, you can unlock the door
with the mechanical key. (Or with the administrator password)
7: It is suggested that one user register with a finger of cach hand in box that the
accident such as injuring fingers happens.
1.3.4 Use of constant open function
I: Enter the state of constant open:
|> Press key 3, verify a registered finger, and press the key of constant open within 5
seconds after the successful verification. After a long “Beep”, the green light on the display
screen will flicker once every 3 seconds (Verification is not needed to open the door in the
state of constant open).
2=Input the administrator password and press the key of constant open after verification,
then the door will be in the state of constant open.
2: Exit the state of constant open:
Fingerprint Security Door Locks User's anual
I> The state of constant open can be cancelled by inputting a fingerprint which can
unlock the door and verifying it successfully.
2> The state of constant open can be cancelled by inputting a administrator password
and verifying it successfully,
1.4 Delete a fingerprint
1.4.1 Delete a super fingerprint
1: Press key 3 directly, the red light on the acquisition screen will be on after a flicker,
Put the administrator fingerprint on the window for acquisition within 5 seconds.
2: After the successful verification of administrator fingerprint, the speaker will give
off a long “Beep” and “00”, the number of administrator fingerprint flickers on the display
screen. The verification of administrator ID is succeeded. (The administrator is allowed to
delete a user).
3: Press key | within 5 seconds, the speaker will give off a long “Beep”, and the
number of fingerprint will appear on the display screen: press key 0 or | to page up or down
to find the No of the fingerprint to be deleted. Press key 3 to confirm to delete the fingerprint
appearing on the display screen.
4: After a successful deletion, the speaker will give off a long “Beep”.
1.4.2 Deleting a user with the password
|: Press key 0 or | to select the number of password and key 3 to confirm. After
confirming the 6-digit password the speaker will give off a long “Beep” and the green light
on the display screen will flicker. Then press key | and the green light is on to enter the state
to delete a user. .
2: At this time, a group of fingerprint numbers will appear on the display screen: press
key 0 or 1 to select the number of the fingerprint to be deleted. And press key 3 to confirm to
delete the fingerprint represented by the number on the display screen.
3: With the administrator fingerprint and password, one can delete any fingerprint with
the number between 01 and 99.
1.4.3 Delete a fingerprint of common user with a super fingerprint
1: Press key 3 directly, the red light on the acquisition screen will be on afer a flicker,
Put the super fingerprint on the window for acquisition within 5 seconds.
2: After the successful verification of super fingerprint, the speaker will give off a long
“Beep” and “01”, the number of the super fingerprint flickers on the display screen. The
verification of ID is succeeded. {The displayed super fingerprint number may be 02, 03, etc.
according to the registered fingerprint).
3: Press key 1 within $ seconds, the speaker will give off a long “Beep”, and the
number of fingerprint between 10 and 99 will appcar on the display screen: press key D or |
to page up or down to find the Mo of the fingerprint to be deleted. Press key 3 to confirm to
delete the fingerprint appearing on the display screen.
4: With a super fingerprint, one can only delete the common users” fingerprint in the
range of 10-99,
1.4.4 Delete all the users
All the fingerprints can be deleted by registering the administrator fingerprint once again.
{Refer to the section “Register the administrator fingerprint” for the operation method)
7
Fingerprint Security Door Locks User's Manual
1.4.5 Modify the administrator password
Repeat the operation of registering the administrator password.
1.5 Operation instruction for mechanical key
1.5.1 The mechanical key
There are 3 mechanical keys in the accessories of the lock which arc also called
emergency key, and they can be used to unlock the door if the password and fingerprint fail to
unlock it.
1.5.2 Unlock the door with a mechanical key
1. Insert the key to the lock cover parallelly into the hole in cover of lock (sec Figure
1-5-0)
2. Rotate the key by 90° clockwise.
3. Pull back the key and remove the cover of lock.
4. Insert the mechanical key into the lock hole vertically. See Figure(1-5-1)
5. Rotate the key by 90° (clockwise for right hand door and counterclockwise for the left
hand door), and now the key is in the horizontal state and the door is opened. See Figure
(1-5-2)
6. Rotate the exterior handle downward by 50° and the door can be opened.
Figure (1-5-0) Figure (1-5-1) Figure (1-5-2)
1.5.3 Lock the door with the mechanical key
1. Rotate the key (counterclockwise for right handed door and clockwise for the left
handed door) by 90°, where the key becomes vertical, and pull out the key, then the door is
locked.
2. Fix the cover of lock when the mechanical key 15 not used.
1.6 Notes for use
To guarantee the safety of your properties, please set yourself as the administrator
and change the default password before putting the fingerprint lock into use.
1.6.1 Low voltage alarm
During the process of normal use, push down key 3 and hear three long tones of
К
Fingerprint Security Door Locks User's Manual
“Beep...becp...becp”. That means the batteries are running out and need to be changed
promptly.
1.6.2 Prompt of successful & failure operation
In normal condition, the speaker will give off a long tone of “beep” and the green light
on the display screen will be on in box of a successful operation. And then enter the
corresponding state. A failure operation will result two short tones of “beep” by the speaker
and the red alarming light on the display screen will be on. Then, exit the state.
1.6.3 The difference between administrator fingerprint and administrator password
The users will not be deleted by covering the prior password with a new one. While the
all the users will be deleted by covering the prior administrator's fingerprint with a new one.
(Except the password)
1.6.4 External emergency power supply
If the batteries are not changed promptly for special reasons, and the power is out, a 9
voltage battery can work as an external emergency power supply. See figure (1-6-0).
Figure (1-6-0)
1.6.5 The lock needs 4 1.5-voltage 5# alkaline batteries. The positive and negative
polarity can’t be connected in the wrong position.
1.6.6 During fingerprint acquisition, the finger shall be flattened against the fingerprint
acquisition window a little stronger.
Fingerprint Security Dwor Locks User's Manual
Chapter 2 Installation instruction
2.1Installation instruction
The instruction is applicable to the following model of lock:
| Smart fingerprint lock of model | |
2.2 Installation requirements
2.2.1 Left & right hand door
[Consider a person outside the door as the reference]
Left hand door (push inward): The person stands outside the door and faces the door. The
hinge of door lock is in the left to the person and the door can only be opened by pushing the door
inward.
Right hand door (push inward): The person stands outside the door and faces the door. The
hinge of door lock is in the right to the person and the door can only be opened by pushing the door
inward.
Left hand door (pull outward): The person stands outside the door and faces the door.
The hinge of door lock is in the left to the person and the door can only be opened by pulling
the door outward.
Right hand door (pull outward): The person stands outside the door and faces the door.
The hinge of door lock is in the right to the person and the door can only be opened by pulling
the door outward.
pe ee a Y
Indoor
— Y
— L
Left hand door (push inward) Right hand door {push inward)
Indoor
—
'
J
В
Left hand door {push outward) Right hand door {push outward)
Figure (1) Schematic drawing of the direction of opening doors
As shown m Figure (1), the door locks can be divided into four types accordingly, i.e. left
hand door (push inward), right hand door (push inward), left hand door (pull outward) and right
hand door (pull outward). During installation, choose the door lock of the same direction as that
of opening the door, or ask the professionals to modify on site
Fingerprint Security Door Locks User's Manual
2.2.2 Installation conditions
1. Wood door. fire-proof door (The hole dimensions should be in accordance with the size
shown in 2.2.3 );
2. Door thickness requirement:
model Smart fingerprint lock series
Minimum scope 35mm
Maximum scope 80mm
To facilitate the installation, please first make sure that whether the thickness of the door
meets the above requirements. When the door thickness is less than the above requirements,
please use the pad provided by our Company.
3. The handle center shall be 1 meter above the floor.
2.2.3 Hole dimensions
= | nn
0.00 Г H | 1 9.00
Pad | | + ta?
eH Nil sh ,
Ly! № “=u Al. 00
y! | | TR TES 50, PA | |
il, ВЖЕ Г м 3.00- 7
ges © cee | high 40.00
sa | % LL” >" above 100. 00--
ем | he |
- ! oor |
rt wo] I ' Ш Ш
Cross section A-A
Figure (2) Hole pattern for smart fingerprint lock series (for door)
Fingerprint Security Door Locks User's Manual
_ ©,
CN | pe
777 | NL TT
| : 1 Е TA -
7 ES
и | ! |
ира = 25.00 RT 1
4 18:09 ab 414.70 O
2 et OC
rd = 1 |
7 Noa]
и —_ | l | |
Va ! | | Em
1 | | | a
AN | 1 SS
«2 i =F | || =.)
QQ | gir | | |
| E
| | |
pi | | |
N po |
_ Г Lil |
Br ® |
a NA.
Cross section A-A
The center of the hole comesponds 10 the center
hing of the door cylinder.
Figure 3 Hole pattern for smart fingerprint lock series (for door frame)
Fingerprint Security Door Locks User's Manual
2.3 Tools of installation
_—
Tape measure Pencil
+
Chisel
~~
Pisto! Drill Solid center bit
Hammer
i pr .
aa" 2
utter kmife Screwdriver Power board
Alloy bio Rg Alloy bile20's; Alloy bito] Ny
Figure 4 Tools required for door lock installation
Fingerprint Security Door Locks User's Manual
2.4 Installation
[the installation procedure takes right hand door (push outward) for example ]
Figure 5 Perspective drawing of the lock
01 Exterior lock set 02 Shim plate of the exterior lock set
03 Square shaft 04 lock cylinder
05 Flat hcad long flat nose self-tapping screw (KA e 06 striking plate
4.0x25)
07 Striking box 08 Door jamb
09 Button head long flat nose [SO-metric screw 10 Button head long Mat nose ISO-metric screw
(OMat.3XMS5X65) (OMa8.5XM5X35)
11 Interior lock set 12 Sham plate of interior lock set
13 Wood door
2.4.1 Installation procedure
1. Determine the baselines and positions of holes
Draw a horizontal line at a certain height (e.g. 100cm) above the bottom of the door as the
centerline of door handle. Align the nick of the centerline of handle on the template with the
centerline of handle, and align the edge of paper board with door edge. Draw the position line
of the hole on both outside and inside of the door (including the outline and centerline of the
hole), and extend the handle centerline to side of the door and draw the side-panel and lock set
outline (as shown in the following figure).
Fingerprint Security Door Locks User's Manual
== Template
Er Door
— = Handle
Е [centerline
— m
Smart fingerprint lock series
2. Drilling holes
Drill holes from both outside and inside of the door. The drilling depth shall be about
half of the door thickness to avoid cracking the door. When drilling the square hole, drill at
the centerline with a drill first, and then with saw the hole to be square with a curve sawing
in accordance with the outline.
la
Smart fingerprint lock series
3. Slotting
Slot the side-panel tank and lock cylinder tank along the door centerline with chisel and
drill in accordance with the size drawing in Section 2.2.3.
Smart fingerprint lock series
4. Installation of lock cylinder
Insert the lock cylinder into the repaired wood door, and fix it on the wood door with
countersunk head self-tapping screws (KA4x25mm), and ensure that the lock-bolt can extend
and retract freely
Fingerprint Security Door Locks User's Manual
Smart fingerprint
lock series
5. Install the exterior lock set
(1): Install the square shaft according to the figure below
Figure 6 Installation of square shaft
(2): Pass the cylinder wire through square hole on (as shown in figure(D) ), then install
the exterior lock set on the door (When the door is not thick enough, please use a
corresponding shim plate, as shown in figure (2) below)
6. Install the interior lock set.
Remove the battery cover and batteries at first, and connect the wire on the interior lock
set with the one on the front lock set (as shown in figure (1), then install the interior lock set
onto the door (as shown in [email protected]), if the thickness or the door is not sufficient, the
corresponding plate should be added)
Fingerprint Security Dwor Locks User's Manual
7. Fix the exterior and interior lock set
First, insert the screws into the corresponding holes, as shown in the following figure D.
Second, tighten the screws with a cross screwdriver (keeping the exterior and interior lock set a
little loose); then, set up the exterior and interior lock set (keeping the exterior and interior lock
set to be symmetric, the lock side shall be parallel with the door side, and the handle and latch
lock-bolt shall move freely); after setting up the exterior and interior lock set and tighten the
screws (keeping the exterior and interior lock set tightened); finally, install the batteries and
interior sliding cover to the interior lock set.
Figure (1)
8. Determine the holes" positions for door striking box and door striking plate
Put the door closc to the door frame and draw the handle centerline on the door frame, and
draw the frames of door striking box and door striking plate in accordance with the hole
dimension on figure 2.2.3.
Fingerprint Security Door Locks User's Manual
|
|
|
|
|
9. Drilling holes for door striking box and door striking plate
Drilling holes for door striking box and door striking plate according to the specified
dimension and trim with a chisel.
hr
f Les
si à
| Lu |
| | Gi |
|
|
= i
10. Install the door striking box and door striking plate
Insert the door striking box and door striking plate into the door jamb, and tighten them
with KA4x25 countersunk head tapping screws.
11. Test the door lock
Test the door lock according to the contents in Chapter | Operating Instructions.
Smart fingerprint lock series
Fingerprint Security Door Locks User's Manual
2.4.2 Notes for installation
I. Examine whether the door thickness is in accordance with the corresponding thickness limit
before installation. In box that the door is not thick enough, please use the shim plate provided
by our Company;
2. During installation, please handle the door lock with care to avoid scratching the surface and
damage to the wires;
3. Before the installation of front lock set, please check if the convex column at the back is in
the state corresponding to that in the figure below:
|. 0 em aa
1% The direction of (he smaller triangle points >
k
to the arrow downside
Scale: 2.0
Smart fingerprint lock series
4. When tightening the M3 screw below the back handle, please turn the handle to the open
state and then tighten the screw;
5. When tightening the front and interior lock set, do not get the internal connection wires under
any thing.
2.5 Additional attentions
77 Standard 1.5V alkaline batteries are required for computer door lock. Do not use acid
batteries to avoid corrosion of the door lock.
Ÿr The computer door lock should be installed after the indoor decoration to avoid pollution
and damage.
77 Install the door closer and door stopper before installing the door lock to avoid damaging
the handle and lock-bolt (square bolt).
TT Protect the handle with protecting jacket before being put to use.
7c Prohibit the illegal operation with foreign bodies to avoid damage to the communication
contacts,
Fingerprint Security Door Locks User's Manual
Chapter 3 Exception Handling
37 Battery replacement
7 Mechanical keys
I the computer board is damaged and the door can’t be unlocked, the mechanical key can
be used to unlock the door.
20
Fingerprint Security Door Locks User's Manual
Chapter 4 Maintenance
ir Lock surface cleaning
To keep the lock surface smooth, please wipe the lock surface with soft, clean and dry
cloth regularly. In order to avoid damage or corrosion, water, alcohol or other chemicals are not
applicable to wipe the lock surface.
Yr Oil the lock
If the lock can not be turned freely or can not maintain correct position, professionals
should be invited to add some mechanical lubricants to the lock cylinder.
+ Replace the lock face and handle
If the lock face and handle have been scratched, new ones can be purchased from our
company for replacement.
Appendix 1: Packing List
| No | _ Name | Quantity Unit Remarks
| 1 | exterior lock set | 1 sel
г 2 interior lock set | set
| 3_| Single lock bolt and cylinder | sel — |
4 striking box |
5 | striking plate ]
6 | Exterior and interior shim plate | foreach | sheet — See fit
— 7 | AA batterics 4 piece I
8 countersunk head self-lapping 4 Used for fixing lock cylinder
screw KA4x25 and striking plate
9 Fixing spindle 2
10 | Cross recessed raised 3
| countersunk head screws
|| Square shaft 1
12 | Mechanical keys 3
13 | Kevs to the lock cover ||
14 | Template ] sheet
[5 | User's manual ]
¡16 | Certificate of Quality ]
| 17 | Warranty card |
Appendix 2: Accessories
Produet accessories are the products-related parts necessary for the use of the product.
Finger print Security Door Locks User's Manual
p =
le 6 Ра al
striking box striking plate Mechanical Key
Bam SSI E
Key cylinder with a
single Lich bolt
F 4 À
= 1 À _—
A x
ju mais X ) и:
, :108 sacd
Key lo the Jock | countersunk head TOS Tecesse
: . Fixed spindle | raised countersunk
“ylinder cover tapping screw
mii ppins head screws
. ' В 4 Me
7 ED i:
| === — В _ J
Big square shall AA batteries shim plate Template
Appendix 3: Warranty Card
After-Sale Services
1. Our company offer free service for one year. The warranty period free of charge is within one
year from the date of purchase.
2. If any of the following situations, which are in the scope of warranty, appear during the
— warranty period, the maintenance shall be charged.
(1) The warranty period is expired or the products are purchased through informal channels
(2) Damages due to improper use, self-demolition, manmade damage or force majeure and
other accidental factors.
(3) Door locks that have been repaired at non-appointed maintenance points.
3. We offer lifelong maintenance, but cost will be charged for the maintenance exceeding the
one-year period.
22
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement