Beechcraft Bonanza V35B Pilot Operating Handbook

Below you will find brief information for V35B. Explore the operational capabilities of the Beechcraft Bonanza V35B with this handbook. It provides essential guidance on airspeed limitations, emergency procedures, normal operations including preflight checks, takeoff, climb, cruise, descent, landing, and shutdown, systems descriptions, and performance data.

PDF

Document

Beechcraft V35B Bonanza

Pilot Operating Handbook

BEECHCRAFT Bonanza V35B

THANK YOU ... for displaying confidence in us by selecting our V35B Bonanza for Microsoft Flight

Simulator. Our design and technical team have utilized their skills and years of experience to ensure that the Bonanza meets the high standards of quality and performance for which FlightSim Developers airplanes have become famous throughout the world.

IMPORTANT NOTICE

This handbook must be read carefully by the owner and operator in order to become familiar with the operation of the V35B Bonanza. The handbook presents suggestions and recommendations to help enhance your simulation experience and efficiently operate the aircraft.

EULA

No part of this manual may be scanned, reproduced, copied, transmitted, distributed, downloaded or used for any purpose without the express written consent of FSD International, Inc.

Information contained herein is subject to change without notice.

USE OF THE HANDBOOK

The Pilot's Operating Handbook is designed to maintain documents necessary for the safe and efficient operation of the Bonanza.

- 1 -

3-View Diagram

Beechcraft V35B Bonanza

Pilot Operating Handbook

- 2 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

BEECHCRAFT Bonanza V35B .....................................................................................................1

Section I General .................................................................................................................5

DESCRIPTIVE DATA ...........................................................................................................5

ENGINE .........................................................................................................................5

PROPELLER....................................................................................................................5

FUEL .............................................................................................................................5

OIL CAPACITY ................................................................................................................5

WEIGHTS ......................................................................................................................5

CABIN DIMENSIONS ........................................................................................................5

BAGGAGE ......................................................................................................................5

Terminology And Symbols ...................................................................................................6

GENERAL AIRSPEED TERMINOLOGY ...................................................................................6

METEOROLOGICAL TERMINOLOGY .....................................................................................7

POWER TERMINOLOGY .....................................................................................................7

ENGINE CONTROLS AND INSTRUMENTS .............................................................................7

WEIGHT AND BALANCE TERMINOLOGY ...............................................................................8

Section II Limitations .......................................................................................................... 10

AIRSPEED LIMITATIONS ................................................................................................... 10

AIRSPEED INDI CATOR MARKINGS ................................................................................... 10

POWER PLANT LIMITATIONS .............................................................................................. 11

ENGINE ....................................................................................................................... 11

FUEL ........................................................................................................................... 11

OIL............................................................................................................................. 11

PROPELLER.................................................................................................................. 11

POWER PLANT INSTRUMENT MARKINGS ........................................................................... 12

WEIGHT AND CENTER OF GRAVITY .................................................................................. 12

APPROVED MANEUVERS (2650 POUNDS) .......................................................................... 13

FLIGHT LOAD FACTORS (2650 POUNDS) ........................................................................... 13

REQUIRED EQUIPMENT FOR VARIOUS CONDITIONS OF FLIGHT ............................................ 13

Emergency Procedures ........................................................................................................ 14

EMERGENCY AIRSPEEDS ................................................................................................... 14

ENGINE FIRE (GROUND) ................................................................................................... 14

ENGINE FAILURE ON TAKE-OFF.......................................................................................... 14

ENGINE MALFUNCTION IN FLIGHT ...................................................................................... 14

ENGINE FAILURE .......................................................................................................... 14

DISCREPANCY CHECKS .................................................................................................. 14

AIR START PROCEDURE ................................................................................................. 15

ENGINE FIRE (FLIGHT) .................................................................................................. 15

EMERGENCY DESCENT ................................................................................................... 15

MAXIMUM GLIDE CONFIGURATION ..................................................................................... 16

EMERGENCY LANDING...................................................................................................... 16

GEAR-UP LANDING........................................................................................................ 16

UNLATCHED DOOR IN FLIGHT ......................................................................................... 16

GENERATOR OUT PROCEDURE ........................................................................................... 16

SPINS ............................................................................................................................ 16

INDUCTION SYSTEM ICING ............................................................................................... 17

EMERGENCY SPEED REDUCTION ........................................................................................ 17

Normal Procedures ............................................................................................................. 18

SPEEDS FOR SAFE OPERATION .......................................................................................... 18

- 3 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

PREFLIGHT INSPECTION ................................................................................................... 18

BEFORE STARTING .......................................................................................................... 18

STARTING ...................................................................................................................... 19

BEFORE TAKE-OFF ........................................................................................................... 20

TAKE-OFF....................................................................................................................... 20

CLIMB ........................................................................................................................... 20

CRUISE.......................................................................................................................... 20

DESCENT ....................................................................................................................... 21

BEFORE LANDING............................................................................................................ 21

SHUTDOWN.................................................................................................................... 21

Systems Description ........................................................................................................... 22

TRIM CONTROL ............................................................................................................... 22

WING FLAPS ................................................................................................................... 22

INSTRUMENT PANEL ........................................................................................................ 22

ENGINE INSTRUMENTS..................................................................................................... 24

MANIFOLD PRESSURE GAUGE AND TACHOMETER............................................................... 24

ENGINE CONTROLS.......................................................................................................... 25

THROTTLE, MIXTURE AND PROPELLER.............................................................................. 25

COWL FLAPS ................................................................................................................ 25

OIL SYSTEM................................................................................................................. 25

STARTER..................................................................................................................... 26

PROPELLER.................................................................................................................. 27

FUEL SYSTEM ............................................................................................................... 27

FUEL QUANTITY............................................................................................................ 28

FUEL TANK SELECTION .................................................................................................. 28

FUEL REQUIRED FOR FLIGHT .......................................................................................... 29

LANDING GEAR SYSTEM ................................................................................................... 29

CONTROL SWITCH ........................................................................................................ 29

POSITION INDICATORS .................................................................................................. 29

WARNING HORN ........................................................................................................... 29

BRAKES....................................................................................................................... 29

GROUND CONTROL ....................................................................................................... 30

ELECTRICAL SYSTEM........................................................................................................ 30

GENERATOR................................................................................................................. 30

LIGHTING SYSTEM........................................................................................................... 31

INTERIOR LIGHTING...................................................................................................... 31

EXTERIOR LIGHTING ..................................................................................................... 31

HEATING AND VENTILATION SYSTEM CABIN HEATING........................................................... 31

PITOT AND STATIC SYSTEM .............................................................................................. 33

VACUUM SYSTEM............................................................................................................. 33

STALL WARNING ............................................................................................................. 33

Performance...................................................................................................................... 34

INTRODUCTION TO PERFORMANCE AND FLIGHT PLANNING .................................................... 34

- 4 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

Section I General

DESCRIPTIVE DATA

ENGINE

The V35B Bonanza is powered by either a Continental E185-1 or E185-8 six cylinder engine rated for a maximum take-off power of 185 hp at 2300 rpm (max. one minute). The maximum continuous rating is

165 hp at 2050 rpm.

PROPELLER

Beech electrically controlled variable pitch, two blade, 88¬inch diameter propeller with Beech pitch control motor and spinner. The propeller uses a Beech R203-100 hub with either R201-217-88 or R203-

218-88 blades.

FUEL

Aviation Gasoline 80/87 (red) minimum grade or alternate grades 100LL (blue) or 100/130 (green).

Standard fuel system: Two 20-gallon tanks in wings. Total 34 gallons usable.

Optional fuel system: Two 20 gallon main tanks in wings and either one 10 gallon or one 20 gallon auxiliary tank installed in the baggage compartment. All of the capacity of the 10 gallon tank is usable.

The 20 gallon tank adds 19 gallons usable fuel to the system.

OIL CAPACITY

The oil capacity is 10 quarts.

WEIGHTS

Maximum Ramp Weight 2660 lbs

Maximum Take-Off Weight 2650 lbs

Maximum Landing Weight 2650 lbs

CABIN DIMENSIONS

Length

Height

6 ft 11 in.

4 ft 2 in,

Width

Entrance Door

BAGGAGE

Volume

Capacity

Baggage Door

3 ft 6 in.

36 in. x 37 in.

16.5 cu ft

270 lbs

22.5 in. x 18.5 in.

- 5 -

TERMINOLOGY AND SYMBOLS

GENERAL AIRSPEED TERMINOLOGY

CAS Calibrated Airspeed is the indicated speed of an airplane, corrected for position and

GS instrument error. Calibrated airspeed is equal to true airspeed in standard atmosphere at sea level.

Ground Speed is the speed of an airplane relative to the ground

IAS

Beechcraft V35B Bonanza

Pilot Operating Handbook

KCAS

KIAS

TAS

Indicated Airspeed is the speed of an airplane as shown on the airspeed indicator when corrected for instrument error. IAS values published in this handbook assume zero instrument error.

Calibrated Airspeed expressed in "knots".

Indicated Airspeed exp ressed in "knots".

True Airspeed is the airspeed of an airplane relative to undisturbed air which is the CAS corrected for altitude, temperature, and compressibility.

Maneuvering Speed is the maximum speed at which application of full available aerodynamic control will not overstress the airplane.

Maximum Flap Extended Speed is the highest speed permissible with wing flaps in a prescribed extended position.

Maximum Landing Gear Extended Speed is the maximum speed at which an airpla ne can be safely flown with the landing gear extended.

Maximum Landing Gear Operating Speed is the maximum speed at which the landing gear can be safely extended or retracted.

Never Exceed Speed is the speed limit that may not be exceeded at any time.

Maximum Structural Cruising Speed is the or Vc speed that should not be exceeded except in smooth air and then only with caution.

Stalling Speed or the minimum steady flight speed at which the airplane is controllable.

Stalling Speed or the minimum steady flight speed at which the airplane is controllable in the landing configuration.

Best Angle-of-Climb Speed is the airspeed which delivers the greatest gain ot altitude in the shortest possible horizontal distance.

Best Rate-of-Climb Speed is the airspeed which delivers the greatest gain in altitude in the shortest possible time.

- 6 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

METEOROLOGICAL TERMINOLOGY

ISA International Standard Atmosphere in which

(1) The air is a dry perfect gas;

(2) The temperature at sea level is 15° Celsius (59° Fahrenheit);

(3) The pressure at sea level is 29.92 inches Hg. (1013.2 millibars);

OAT

(4) The temperature gradient from sea level to the altitude at which the temperature is -56.5° C (-

69.7° F) is -0.00198° C (-0.003566° F) per foot and zero above that altitude.

Outside Air Temperature is the free air static temperature obtained either from in-flight temperature indications adjusted for instrument error and compressibility effects, or ground

Indicated

Pressure

Altitude

Pressure

Altitude

Station

Pressure meteorological sources.

The number actually read from an altimeter when the barometric sub¬scale has been set to

29.92 inches of mercury (1013.2 millibars).

Altitude measured from standard sea-level pressure (29.92 in. Hg) by a pressure or baro metric altimeter.

It is the indicated pressure altitude corrected for position and instrument error. In this

Handbook, altimeter instrument errors are assumed to be zero. Position errors may be obtained from the Altimeter Correction Chart. Actual atmospheric pressure at field elevation.

The wind velocities recorded as variables on the charts of this handbook are to be understood Wind as the headwind or tailwind components of the reported winds.

POWER TERMINOLOGY

Take off Maximum power rating, limited by time.

Maximum

Continuous

Cruise

Highest power rating not limited by time.

Power recommended for cruise climb.

Climb

ENGINE CONTROLS AND INSTRUMENTS

Throttle Used to control power by introducing fuel-air mixture into the intake passages of the engine. Settings are reflected by readings on the manifold pressure gauge. Control

Mixture

Control

This control is used to set fuel to air ratio in all modes of operation and cuts off fuel completely for engine shut down.

EGT

Tachometer

ADI

Exhaust Gas Temperature Indicator. This indicator is used to identify the lean and best power fuel/air mixtures for various power settings.

Indicates the rpm of the engine/ propeller.

Automatic Direction Indicator (artific ial horizon)

RMI Radio Magnetic Indicator

- 7 -

Standard

Empty

Weight

Basic

Empty

Weight

Payload

Useful

Load

Maximum

Ramp

Weight

Maximum

Take-off

Weight

WEIGHT AND BALANCE TERMINOLOGY

Reference

Datum

An imaginary vertical plane from which all horizontal distances are measured for balance purposes.

Station

Arm

A location along the airplane fuselage usually given in terms of distance from the reference datum.

The horizontal distance from the reference datum to the center of gravity (C.G.) of an item.

Moment

Airplane

Center of

Gravity

(C. G.)

C.G. Arm

Beechcraft V35B Bonanza

Pilot Operating Handbook

The product of the weight of an item multiplied by its arm. (Moment divided by a constant is used to simplify balance calculations by reducing the number of digits.)

The point at which an airplane would balance if suspended. Its distance from the reference datum is found by dividing the total moment by the total weight of the airplane.

C.G.

Limits

Usable

Fuel

Unusable

Fuel

The arm obtained by adding the airplane’s individual moments and dividing the sum by the total weight.

The extreme center of gravity locations within which the airplane must be operated at a given weight.

Fuel available for flight planning.

Fuel remaining after a runout test has been completed in accordance with governmental regulations.

Weight of a standard airplane including unusable fuel, full operating flu ids and full oil.

Standard empty weight plus optional equipment.

Weight of occupants, cargo and baggage.

Difference between take off weight, or ramp weight if applicable, and basic empty weight.

Maximum weight approved for ground maneuvering. (It includes weight of start, taxi, and run up fuel).

Maximum weight approved for the start of the take off run.

- 8 -

Maximum

Landing

Weight

Zero Fuel

Weight

Maximum weight approved for the landing touchdown.

Weight exclusive of usable fuel.

This space left intentionally blank

Beechcraft V35B Bonanza

Pilot Operating Handbook

- 9 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

Section II Limitations

The limitations included in this section have been approved by the Federal Aviation Administration.

The following limitations must be observed In the operation of this airplane.

AIRSPEED LIMITATIONS

SPEED

Never Exceed

VNE

CAS IAS

REMARKS

KNOTS MPH KNOTS MPH

176 202 177 204 Do not exceed this speed in any operation

Maximum Structural

Cruising V

or Vc

139 160 140

Maneuvering

113

Maximum Flap

Extension/Extended

VFE

Maximum Landing

Gear Operating!

Extended VLO and VLE

109

130

105

125

114

110

161 Do not exceed this speed except in smooth air and then only with caution

131 Do not make full or abrupt control movements above this speed

105 Do not extend flaps or operate with flaps extended above this speed

127 Do not extend, retract or operate with landing gear extended above this speed except in emergency

AIRSPEED INDICATOR MARKINGS

CAS

MARKING

KNOTS MPH

IAS

KNOTS MPH

White Arc 49-91 56-105 45-91

SIGNIFICANCE

52-105 Full Flap Operating Range

Green Arc

Yellow Arc

Red Line

58-139 67-160 54- 140 62-161 Normal Operating Range

139-176 160-202 140-1 77 161-204 Operate with caution only in smooth air

176 202 177 204 Maximum speed for ALL operations

- 10 -

POWER PLANT LIMITATIONS

ENGINE

A35 Continental E 185-1 or E 185-8

Take-off

(one minute) ………………………………… 2300 rpm, Full throttle

Maximum continuous operation ……………………………………… 2050 rpm, Full throttle

Beechcraft V35B Bonanza

Pilot Operating Handbook

B35 Continental E185-8 (S/N 51220 and above)

Take-off

(one minute)………………………………… 2450 rpm, Full throttle

Maximum continuous operation …………………………………….. 2050 rpm, Full throttle

NOTE

Other engines are approved for this model Bonanza but not installed as original equipment. These are listed in the FAA

Aircraft Specification A-777 or approved by Supplemental

Type Certificate.

FUEL

Aviation Gasoline 80/87 (red) minimum grade or alternate grades 100LL (blue) or 100/130 (green). See

Engine Manufacturer's Bulletin.

OIL

Ashless dispersant oils must meet Continental Motors Corporation Specification MHS-24A.

PROPELLER

Beech - two blade. 88 inch diameter (max.) propeller.

- 11 -

POWER PLANT INSTRUMENT MARKINGS

OIL TEMPERATURE

Caution (Yellow Radial)

Operating Range (Green Arc)

100°F/38°C

100° to 225°F/38° to 107°C

Maximum (Red Radial)

OIL PRESSURE

Minimum Pressure (Red Radial)

Operating Range (Green Arc)

225°F/107°C

30 psi

30 to 60 psi

Beechcraft V35B Bonanza

Pilot Operating Handbook

Maximum Pressure (Red Radial)

TACHOMETER

Operating Range (Green Arc)

Cautionary Range (Yellow Arc)

80 psi

1300 to 2050 rpm

2050 to 2300 rpm

Maximum RPM (Red Radial)

CYLINDER HEAD TEMPERATURE

Operating Range (Green Arc)

2300 rpm

300° to 460°Fj149° to 238°C

Maximum Temperature (Red Radial) 525°F;274°C

MANIFOLD PRESSURE

Operating Range (Green Arc)

Maximum (Red Radial)

FUEL PRESSURE

Minimum (Red Radial)

Operating Range (Green Arc)

Maximum (Red Radial)

15 to 29.6 in. Hg

29.6 in. Hg

9 psi

11 to 14 psi

14 psi

WEIGHT AND CENTER OF GRAVITY

Maximum Take-off and Landing Weight

Maximum Ramp Weight

Zero Fuel Weight

Aft:

2650 lbs

2660 lbs

No Structural Limitation

Datum is 83.1 inches forward of center line through forward jack points.

MAC leading edge is 66.7 inches aft of datum. MAC length is 65.3 inches.

CG LIMITS (Gear Down)

Forward: 75.9 inches aft of datum to 2140 lbs with straight line variation to 83.7 inches at 2650 lbs.

85.4 inches aft of datum to 2405 lbs with straight line variation to 84.4 inches at 2650 lbs.

- 12 -

APPROVED MANEUVERS (2650 POUNDS)

MANEUVER

Chandelle

Steep Turn

Lazy Eight

ENTRY SPEED (CAS)

113 kts/130 mph

Stall (Except Whip) Use slow deceleration

Spins are prohibited.

FLIGHT LOAD FACTORS (2650 POUNDS)

Beechcraft V35B Bonanza

Pilot Operating Handbook

4.4G positive maneuvering load factor with flaps up. 2.0G positive maneuvering load factor with flaps down.

REQUIRED EQUIPMENT FOR VARIOUS CONDITIONS OF FLIGHT

Federal Aviation Regulations (91.3(a), 91.24, 91.25, 91.32, 91.33, 91.52, 91.90, 91.97,91.170) specify the minimum numbers and types of airplane instruments and equipment which must be installed and operable for various kinds of flight conditions. This includes VFR day, VFR night, IFR day, and IFR night.

Regulations also require that all airplanes be certificated by the manufacturer for operations under various flight conditions. At certification, all required equipment must be in operating condition and should be maintained to assure continued airworthiness. If deviations from the installed equipment were not permitted, or if the operating rules did not provide for various flight conditions, the airplane could not be flown unless all equipment was operable. With appropriate limitations. the operation of every system or component installed in the airplane is not necessary, when the remaining operative instruments and equipment provide for continued safe operation. Operation in accordance with limitations established to maintain airworthiness, can permit continued or uninterrupted operation of the airplane temporarily.

For the sake of brevity, the Required Equipment Listing does not include obviously required items such as wings, rudders, flaps, engine, landing gear, etc. Also the list does not include items which do not affect the airworthiness of the aircraft such as galley equipment, entertainment systems, passenger convenience items, etc. However, it is important to note that ALL ITEMS WHICH ARE RELATED TO THE

AIRWORTHINESS OF THE AIRPLANE AND NOT INCLUDED ON THE LIST ARE AUTOMATICALLY REQUIRED

TO BE OPERATIVE.

To enable the pilot to rapidly determine the FAA equipment requirements necessary for a flight into specific conditions, the following equipment requirements and exceptions are presented. It is the final responsibility of the pilot to determine whether the lack of, or inoperative status of a piece of equipment on his airplane, will limit the conditions under which he may operate the airplane.

NOTE

FLIGHT IN KNOWN ICING CONDITIONS PROHIBITED.

- 13 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

Emergency Procedures

EMERGENCY AIRSPEEDS

Emergency Descent 110 kts/127 mph

Glide

Emergency Landing

Approach

105 kts/121 mph

70-76 kts/81-87 mph

All airspeeds quoted in this section are indicated airspeeds (IAS).

The following information is presented to enable the pilot to form, in advance, a definite plan of action for coping with the most probable emergency situations which could occur in the operation of the airplane. Where practicable, the emergencies requiring immediate corrective action are treated in check list form for easy reference and familiarization. Other situations, in which more time is usually permitted to decide on and execute a plan of action, are discussed at some length.

ENGINE FIRE (GROUND)

Mixture - IDLE CUT -OFF

Fuel Selector Valve - OFF

ENGINE FAILURE ON TAKE-OFF

Battery, Generator and Ignition Switches - OFF

Extinguish with Fire Extinguisher.

DURING GROUND ROLL

Throttle - CLOSED

Braking - MAXIMUM

Fuel Selector Valve - OFF

Battery and Generator Switches - OFF

If airborne and insufficient runway remains for landing:

Fuel Selector Valve - SELECT OTHER MAIN TANK

Auxiliary (Wobble) Fuel Pump - PUMP (9 TO 10 P.S.I.)

Mixture - FULL RICH

IF NO RESTART

Ignition - CHECK, ON BOTH

Select most favorable landing site.

See EMERGENCY LANDING procedure.

3. The use of landing gear is dependent on the terrain where landing must be made.

ENGINE MALFUNCTION IN FLIGHT

ENGINE FAILURE

The most probable cause of engine failure would be loss of fuel flow or improper functioning of the ignition system.

DISCREPANCY CHECKS

(Rough running engine, loss of engine power, loss of fuel flow, etc.)

1. Rough Running Engine a. Mixture - FULL RICH, then lean as required b. Ignition Switch - CHECK on BOTH position

- 14 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

2. Loss of Power a. Fuel Pressure Gage - CHECK (fuel pressure abnormally low)

(1) Mixture - FULL RICH

(2) Auxiliary (Wobble) Fuel Pump - MAINTAIN FUEL PRESSURE

(3) Auxiliary (Wobble) Fuel Pump - STOP if performance does not improve in a few moments b. Fuel Quantity Indicator - CHECK (fuel tank being used is empty)

(1) Select other tank (check to feel detent) c. Carburetor Heat - Pull full carburetor heat and check for manifold pressure drop. Push

3. a. b. c. carburetor heat to cold position - manifold pressure should return to original position.

Propeller Overspeed

Retard throttle to reduce RPM to red line.

Propeller switch to manual LO RPM.

Reduce speed to assist in maintaining altitude. d.

AIR START PROCEDURE a. b.

Select nearest landing site, follow emergency landing procedures.

Mixture - IDLE CUT -OFF

Fuel Selector Valve - OFF to clear engine then TO MAIN TANK MORE NEARLY FULL

NOTE

If the failure was due to the fuel metering valve sticking in the full open position, the carburetor will deliver an excess of fuel, with constant flooding. Shutting off fuel momentarily will clear the engine and may restore normal operation by allowing the spring in the carburetor to reseat the valve. c. d. e.

Throttle - 1/4 INCH OPEN

Mixture - FULL RICH

Auxiliary (Wobble) Fuel Pump - MAINTAIN FUEL PRESSURE f. Throttle - ADVANCE to desired power

ENGINE FIRE (FLIGHT)

The red VENT SHUTOFF control on the outboard side of the right lower subpanel is used to close off all heating system outlets so that smoke and fumes will not enter the cabin. In the event of engine fire, shut down the engine as follows and make a landing:

Vent Shutoff Control - PULL TO CLOSE

Mixture - IDLE CUT -OFF

Fuel Selector Valve - OFF

Battery, Generator, and Ignition Switches - OFF (Extending the landing gear can be accomplished manually if desired.)

Do not attempt to restart engine.

EMERGENCY DESCENT

Power - IDLE

Propeller - HI RPM

Landing Gear - DOWN

Airspeed - ESTABLISH 110 kts/127 mph

- 15 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

MAXIMUM GLIDE CONFIGURATION

Landing Gear - UP

Flaps - UP

Cowl Flaps - CLOSED

Glide distance is approximately 1.7 nautical miles (2 statute miles) per 1000 feet of altitude above the terrain.

Propeller - LO RPM

Airspeed - 105 kts/121 mph

EMERGENCY LANDING

When assured of reaching the landing site selected, and on final approach:

Airspeed - Establish 70 to 76 kts;81 to 87 mph

Fuel Selector Valve - OFF

Mixture - IDLE CUT -OFF

Flaps - AS REQUIRED

Landing Gear - DOWN OR UP, DEPENDING ON TERRAIN

Battery, Generator and Ignition Switches - OFF

GEAR- UP LANDING

If possible, choose firm sod or foamed runway. Make a normal approach, using flaps as necessary. When you are sure of making the selected landing spot:

Throttle - CLOSED

Mixture - IDLE CUT -OFF

Battery, Generator and Ignition Switches - OFF

Fuel Selector Valve - OFF

Keep wings level during touchdown.

Get clear of the airplane as soon as possible after it stops.

UNLATCHED DOOR IN FLIGHT

If the cabin door is not locked it may come unlatched in flight. This may occur during or just after takeoff. The door will trail in a position approximately 3 inches open, but the flight characteristics of the airplane will not be affected. except that rate of climb will be reduced. Return to the field in a normal manner. If practicable, during the landing flare-out have a passenger hold the door to prevent it from swinging open.

GENERATOR OUT PROCEDURE

A failure of the generator will place the entire electrical operatio n of the aircraft on the battery.

Generator failure may be indicated by the ammeter. When a generator failure occurs in flight, all nonessential electrical load should be discontinued to conserve the battery life.

SPINS

Spins are prohibited. If a spin is entered inadvertently:

Immediately move the control column full forward and simultaneously apply full rudder opposite to the direction of the spin; continue to hold this control position until rotation stops and then neutralize all

- 16 -

Beechcraft V35B Bonanza

Pilot Operating Handbook controls and execute a smooth pullout. Ailerons should be neutral and throttle in idle position at all times during recovery.

INDUCTION SYSTEM ICING

The possibility of fuel icing is reduced by the design of the pressure carburetor. Under certain conditions, however, impact ice can form at several points in the induction system. As with fuel ice, the first indication of impact ice formation probably will be a slight drop in manifold pressure. During possible icing conditions, any such drop should be investigated immediately.

To check for carburetor ice in possible icing conditions: a.

Note manifold pressure, then, apply full carburetor heat. Manifold pressure will drop slightly. Do not correct for this drop.

After one or two minutes, switch back to cold air. If manifold pressure rises higher than the point observed before applying carburetor heat, carburetor icing is indicated.

Apply carburetor heat immediately until icing conditions no longer exist. Use high

EMERGENCY SPEED REDUCTION power settings and lean mixtures to produce maximum heat under possible icing conditions.

In an emergency, the landing gear may be used to create additional drag. Should disorientation occur under instrument conditions, the lowering of the landing gear will reduce the tendency for excessive speed build-up. This procedure would also be appropriate for a non-instrument rated pilot who unavoidably encounters instrument conditions or in other emergencies such as severe turbulence.

Should the landing gear be used at speeds higher than the maximum extension speed, a special inspection of the gear doors in accordance with maintenance manual procedures is required, with repair as necessary.

- 17 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

Normal Procedures

All airspeeds quoted in this section are indicated airspeeds (IAS)

SPEEDS FOR SAFE OPERATION

Take-off

Lift-off 50 Ft.

64 kts

70 kts

Maximum Climb

Best Rate

Best Angle

89 kts

72 kts

Cruise Climb

Maximum Turbulent

Air Penetration

Balked Landing

Landing Approach

Maximum Demonstrated

104 kts/120 mph

114 kts

65 kts

Crosswind

PREFLIGHT INSPECTION

CABIN: a.

17 Kts

Parking Brake - SET

Control Lock - REMOVE

All Switches - OFF

Emergency Locator Transmitter - ARMED

RIGHT FUSELAGE:

Baggage Compartment Door - SECURE

Static Pressure Button - UNOBSTRUCTED

EMPENNAGE: a.

Control Surfaces - CHECK

Tie Down - REMOVE

Position Light - CHECK

BEFORE STARTING

Seat Belts and Shoulder Harnesses - FASTEN

Parking Brake - SET

All Avionics - OFF

Circuit Breakers - IN

Landing Gear Handle - DOWN

Flaps - UP

Cowl Flaps - OPEN

Light Switches - OFF

Battery and Generator Switches - ON (If external power is used, turn Generator Switch - OFF)

10.

Ignition Switch - BATTERY

11.

Fuel Quantity Indicators - CHECK QUANTITY

- 18 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

WARNING

Do not take off if gauges indicate in yellow arc or with less than 10 gallons in each main tank.

12.

Activate the selector valve several times by rotating the handle from tank to tank to ensure that the se• lector valve is free.

13.

Fuel Selector Valve - SELECT LEFT MAIN TANK.

STARTING

CAUTION

Vernier-type engine controls should not be rotated clockwise after being advanced to the full forward position.

Mixture - FULL RICH

NOTE

Propeller - HI RPM

On governor equipped propeller, switch in AUTO and governor control at TAKE-OFF.

Throttle - OPEN (2 or 3 turns of vernier.)

Ignition Switch - BOTH

Auxiliary (wobble) Fuel Pump - Pump and maintain 9 to 10 P.S.I.

Starter Button - Press until engine starts.

NOTE

Primer - Brief shots until engine starts firing

If a false start occurs or the starter button is released after the ignition switch has been turned to the

BOTH position, the ignition switch must be turned to the BATT position before the starter button will again energize the starter.

NOTE

If starting fuel pressure is low, maintain pressure with auxiliary (wobble) fuel pump until pressure stabilizes.

In the Event of Overprime Condition: a.

Mixture - IDLE CUT -OFF

Throttle - OPEN

Starter Button - PRESS

As engine starts reduce throttle to IDLE and advance mixture to FULL RICH

Oil Pressure - CHECK

10.

External Power (if used) - DISCONNECT. Battery and Generator Switches ON.

11.

Warm up - 1000 to 1200 rpm.

NOTE

Do not operate engine above warm-up speed until oil temperature reaches 100°F (38°C).

12.

13.

All Engine Indicators - CHECK

Avionics Equipment - AS REQUIRED

14.

Lights - AS REQUIRED

- 19 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

BEFORE TAKE-OFF

Parking Brake - SET

Radios - CHECK

Engine Instruments - CHECK

Flight Instruments - CHECK and SET

Throttle - 1900 RPM

Propeller - Hold Propeller Control Switch in LO RPM position until a decrease in RPM is noted, and then hold switch to HI RPM until RPM is regained.

Check Automatic Propeller Control by moving propeller switch to the AUTO position and

turning APC knob full left until RPM starts to decrease, then turn knob to the Take-Off position (full right),

Magnetos - CHECK at 1600 rpm. Drop should not exceed 75 rpm on either magneto, and should be within 50 rpm of each other.

Carburetor Heat - CHECK and return to COLD

Trim - SET a.

Aileron - NEUTRAL

Elevator - 00 (30 nose down for aft loading)

10.

Flaps - UP

11.

Door and Windows - SECURE

12.

Seat Belts and Shoulder Harnesses - SECURE

NOTE

All reclining seats must be in the upright position during take-off.

13.

Controls - FREE

14.

Mixture - FULL RICH (or as required by field elevation)

15.

Brakes - RELEASED

16.

Instruments - CHECK, make final check of manifold pressure, fuel pressure, and rpm at the start of the take-off run. Oil temperature less than 215°F.

TAKE-OFF

Take-Off Power (B35)

(1 min.) Full throttle, 2450 rpm

Power - SET TAKE-OFF POWER AND RELEASE BRAKES

Airspeed - ACCELERATE TO RECOMMENDED SPEED

Landing Gear - RETRACT (when positive rate of climb is established)

Airspeed - ESTABLISH DESIRED CLIMB SPEED (when clear of obstacles)

Propeller - 2050 rpm.

CLIMB

Climb Full throttle, 2050 rpm

Engine Temperatures - MONITOR

Power - SET AS DESIRED.

CRUISE

Cowl Flaps - CLOSED

Power - SET

Mixture - ADJUST

- 20 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

DESCENT

Power - SET AS DESIRED (Avoid prolonged idle setting and low cylinder head temperatures)

Mixture - Enrich as required.

Carburetor Heat - As required.

BEFORE LANDING

NOTE

Seat Belts and Shoulder Harnesses - SECURE

All reclining seats must be in the upright position during landing.

Fuel Selector Valve - SELECT MAIN TANK MORE NEARLY FULL

Cowl Flaps - AS REQUIRED

Mixture - FULL RICH

Carburetor Heat - COLD

NOTE

If icing conditions are indicated, carburetor heat may be carried: however, less power will be available for a go-around.

Landing Gear - DOWN and CHECK. (Maximum extension speed 110 kts/127 mph)

Flaps - DOWN (Maximum extension speed 92 kts/106 mph)

Airspeed - ESTABLISH NORMAL LANDING AP¬PROACH SPEED.

Propeller a.

NOTE

Manual - Hold to HI RPM until maximum is attained.

Automatic Propeller Control (APC) - Select AUTO CLIMB.

For Balked Landing, advance throttle, retract gear and flaps, select AUTO TAKE-OFF, moni¬tor engine

RPM and do not exceed red line.

SHUTDOWN

1, Cowl Flaps - OPEN

Brakes - SET

Electrical and Radio Equipment - OFF

Flaps - UP

Propeller - HI RPM

Carburetor Heat - COLD

Throttle - CLOSE

Mixture - IDLE CUT -OFF

Ignition Switch - OFF, after engine stops

10.

Battery and Generator Switches - OFF

11.

Control lock - INSTALL, if conditions warrant.

12.

Install wheel chocks and release brakes if the airplane is to be left unattended.

- 21 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

Systems Description

TRIM CONTROL

Elevator trim is controlled by a handwheel located to the left of the throttle.

An elevator tab indicator dial is located immediately below the control column.

WING FLAPS

The flaps are raised and lowered electrically by jackscrew actuators driven through flexible shafts from a single motor and gearbox under the front seat.

INSTRUMENT PANEL

The instrument panel for this airplane consists of fixed and floating panels, an engine instrument cluster on the center of the instrument panel above the control column, a radio grouping on the left side of the instrument panel and subpanels which provide a compact circuit breaker group on the right side, and switch panels on both sides.

Standard instrumentation on the Bonanza includes an airspeed indicator, altimeter and electric turn-andbank indicator mounted in the instrument panel; magnetic compass mounted on the windshield divider; a clock mounted in the instrument panel, and outside air thermometer at the top of the divider.

In addition to several radio-navigation combinations, optional instruments for which openings are provided in the instrument panel include a vacuum-operated directional gyro and attitude gyro, and the suction gauge necessary when these instruments are installed.

The battery master switch and generator switches are located under a door in a panel under the right side of the instrument panel. The key operated battery ignition switch is located below the control column.

Toggle type key switches on the right and left subpanels operate landing gear, flaps, exterior lighting, fuel gauge selectors, and radios.

The Bonanza is powered by a Continental E185-8 six-cylinder, horizontally opposed engine rated at 185 hp at 2300 rpm for take-off (max. one minute).

- 22 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

1. Clock

2. Airspeed

3. ADI

4. Altimeter

5. Manifold Pressure

6. Tachometer

7. OAT Gauge

8. RMI

9. Turn Coordinator

10. HSI 19. Switch Panel

11. Vertical Speed

12. Oil Gauge

20. Heat/AC Ctrls

21. Vacuum Gauge

13. CHT Gauge 22. Batter Bus Volts

14. Battery Bus Amps 23. Elevator Trim

15. Left Fuel Qty

16. Wing Tanks Qty

24. Cowl Flaps Ctrl

25. Flaps Ctrl

17. Right Fuel Qty 26. Gear Ctrls

18. Starter/Magnetos 27. Throttle

28. Prop RPM Ctrl

29. Fuel Mixture

30. Alt Air Source

31. Audio Panel

32. GNS 480 GPS

33. NAV/COM Radio

34. DME Radio

35. ADF Radio

36. Autopilot

- 23 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

ENGINE INSTRUMENTS

The engine instruments include: cylinder head temperature, oil temperature, oil pressure indicators, tachometer, manifold pressure, fuel pressure, and fuel quantity indicators, and an ammeter.

Except for the tachometer and manifold pressure gauge, the power plant instruments are grouped together immediately above the control console. The engine gauge cluster includes the fuel quantity and fuel pressure gauges, oil pressure gauge, the oil temperature and cylinder head temperature indicators and ammeter.

MANIFOLD PRESSURE GAUGE AND TACHOMETER

The manifold pressure gauge and tachometer are mounted in the instrument panel proper. The tachometer is driven by a flexible shaft from the engine accessory section.

Incorporated in the tachometer is an engine hour meter which automatically records the total engine operating time.

- 24 -

ENGINE CONTROLS

THROTTLE, MIXTURE AND PROPELLER

COWL FLAPS

Beechcraft V35B Bonanza

Pilot Operating Handbook

The push-pull throttle and mixture controls are located on and to the left of the control console respectively. These controls are released for repositioning by pushing a button on the knob.

With the button extended.

On the mixture control, releasing the knob locks the control. The control is pushed in for full rich and pulled out to the end of its travel for idle cutoff.

Propeller pitch is controlled by a three-position toggle switch on the control console, just to the left of the throttle.

The push-pull cowl flap control is located to the left of the control console on the subpanel. Except in extremely low temperatures. The cowl flaps should be open during ground operation, take-off, and climb.

OIL SYSTEM

In the Bonanza's oil system, oil is fed to the engine oil pump from a supply tank mounted just above and behind the engine. The return oil is picked up by a scavenging pump and returned to the supply tank, passing through a cooler which is an integral part of the tank. The oil tank capacity is 2-1;2 gallons. The filler neck of the A35 is accessible by raising the left engine cowling. The B35 has an access door on the left upper cowl. The level should be checked after each flight using the dipstick fastened to the filler cap.

The normal oil operating level should be maintained at 8 to 10 quarts. Both oil pumps, the oil screen and a check valve to prevent oil from draining from the tank into the engine sump are incorporated in the engine accessory section. There is no engine oil shut-off valve and the system is so designed that oil bypass arrangements are unnecessary.

- 25 -

OIL SYSTEM SCHEMATIC

Beechcraft V35B Bonanza

Pilot Operating Handbook

STARTER

The starter is relay-controlled to minimize the length of heavy cable required to carry the high amperage of the starter circuit. The starter is actuated by a key type, momentary-on switch located on the left of the control column. To energize the starter circuit, rotate the ignition switch to the START position and hold. Before starting it is necessary that the subpanel battery switch be turned on.

- 26 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

PROPELLER

Beech electrically controlled variable pitch, two blade, 88 inch diameter propeller with Beech pitch control motor and spinner. The propeller uses a Beech R203-100 hub with either R201 -217 -88 or

R203-218-88 blades.

FUEL SYSTEM

The airplane is designed for operation on 80A37 grade (red) aviation gasoline. In the event this grade is not available only a higher rated fuel shall be used.

CAUTION

Before refueling, make certain the airplane and fuel dispensing unit are properly grounded. Failure to do so creates a fire hazard.

- 27 -

FUEL QUANTITY

Fuel quantity is measured by float operated sensors, located in each fuel tank. These transmit electrical signals to the indicator through selector switches on the panel that indicate fuel remaining in the tank selected. There are sensors in each fuel tank connected to the switches and indicator.

The fuel level of the fuselage auxiliary cell may be read by switching the auxiliary fuel gauge selector switch on the subpanel to Aux position.

FUEL TANK SELECTION

Beechcraft V35B Bonanza

Pilot Operating Handbook

The fuel selector unit handle is located forward and to the left of the pilot's seat.

Take-offs should be made using the left main tank and landings should be made using the main tank that is more nearly full. In no case should a take-off be made if the fuel indicators are in the yellow band or, with less than 10 gallons of fuel in each main tank.

SWITCHING FUEL TANKS

When switching fuel tanks, if one tank is allowed to run completely dry, it may be necessary to place the mixture control to Full

Rich position and maintain fuel pressure with the Auxiliary Fuel Pump switch to aid in restarting the engine. Close the throttle as necessary to prevent engine overspeed on starting. As soon as the engine is running normally, discontinue the Auxiliary Fuel

Pump and reset the mixture control.

The pressure type carburetor returns about 3 gallons per hour of excess fuel to the left main cell regardless of the cell selected. To provide space for the returned fuel, the left main cell should be used to approximately half full before switching. If the engine is allowed to stop firing due to insufficient fuel refer to the EMERGENCY PROCEDURES section for the Air Start procedures.

- 28 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

FUEL REQUIRED FOR FLIGHT

It is the pilot's responsibility to ascertain that the fuel quantity indicators are functioning and maintaining a reasonable degree of accuracy, and be certain of ample fuel for a flight. Takeoff is prohibited if the fuel quantity indicators do not indicate above the yellow arc. An inaccurate indic ator could give an erroneous indication of fuel quantity. A minimum of 10 gallons of fuel is required in each main tank before takeoff.

LANDING GEAR SYSTEM

CAUTION

Never taxi with a flat strut.

The landing gears are operated through adjustable linkage connected to an actuator assembly mounted beneath the front seats. The actuator assembly is driven by an electric motor. The landing gears may be electrically retracted and extended, and in an emergency may be extended manually.

CONTROL SWITCH

The landing gear is controlled by a two-position switch on the right side of the subpanel. A latch on the control switch must be moved aside to place the switch in the up position.

POSITION INDICATORS

Landing gear position indicator lights on the right side of the control console show red when the gear is up, or green when it is down, illuminating only when the actuator assembly reaches either extreme. In addition, a mechanical indicator on the floorboard beneath the control console shows the position of the nose gear. Its pointer is linked by a cable to the actuating mechanism and moves simultaneously with it.

Limit switches and a dynamic brake automatically stop the retract mechanism when the gear reaches it’s full up or full down position.

CAUTION

Never rely on the safety switch to keep the gear down during taxi or on take-off, landing roll, or in a static position. Always make certain that the landing gear switch is in the down position during these operations.

WARNING HORN

With the landing gear retracted, if the throttle is retarded below approximately 12 in. Hg manifold pressure, a warning horn will sound intermittently.

BRAKES

The brakes on the main landing gear wheels are operated by applying toe pressure to the rudder pedals.

The parking brake handle is located on the left side of the control console. To set the parking brakes, pull handle back and depress both toe pedals until firm. Push the handle forward to release the brakes.

NOTE

The parking brake should be left off and wheel chocks installed if the airplane is to be left unattended.

Changes in ambient temperature can cause the brakes to release or to exert excessive pressures.

- 29 -

GROUND CONTROL

Steering is accomplished by use of the rudder pedals through a linkage arrangement which connects the nose strut to the rudder pedal shaft. Nose wheel straightening is accomplished by engagement of a roller with a track as the nose wheel is retracted. The steering link attaches to the steering mechanism on the nose strut with a swivel connection which permits the mechanism to disengage when the nose gear is retracted and operation of the rudder pedals will have no tendency to turn the nose wheel with the gear retracted.

ELECTRICAL SYSTEM

Beechcraft V35B Bonanza

Pilot Operating Handbook

The system circuitry is the single wire, ground return type, with the aircraft structure used as the ground return. The battery ON-

OFF switch and the generator ON-OFF switch are located on the switch subpanel on the pilot’s lower panel.

GENERATOR

Direct-current electric power is supplied by a 25 ampere engine-driven generator controlled by a voltage-current regulator which automatically adjusts generator output to its load, including recharging the battery.

The ammeter is of the conventional charge-discharge type, showing the rate of charge or discharge of the battery. A zero reading, which should be the normal condition in cruising flight, indicates that the battery is fully charged and the generator output has been adjusted by the regulator to balance the load of electrical equipment then in use.

- 30 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

LIGHTING SYSTEM

The Light Control Panel is located on the switch panel on the lower section of the pilot’s instrument panel.

INTERIOR LIGHTING

Lighting for the instrument panel is furnished by a light in the cabin ceiling. It is controlled by the INST switch on the Light Control Panel.

EXTERIOR LIGHTING

The switches for all of the exterior lights are located on the Light Control Panel. The exterior lights consist of navigation lights and landing lights. For longer battery and lamp life, use the landing lights sparingly; avoid prolonged operation which could cause overheating during ground maneuvering.

HEATING AND VENTILATION SYSTEM CABIN HEATING

A heater muffler on the left exhaust stack provides for heated air to five outlets in forward and aft areas of the cabin. Two forward outlets are located above and forward of each set of rudder pedals. One aft outlet is installed behind the right front seat. Two outlets provide heated air for windshield defrosting.

HEATER OPERATION

The cabin heat control is located on the lower pilot's subpanel. To obtain heated air to the cabin outlets, pull the

CABIN HEAT control. The control regulates the amount of cold air that is mixed with the air from the heater muff.

When the control is pulled fully out, the cold air is shut off and only heated air enters the cabin.

The forward vents, located on the firewall forward of the rudder pedals, deliver heated air to the forward cabin when the CABIN HEAT control is pulled out. For maximum heat the control is pulled fully out.

To obtain increased heated air for defrosting the windshield close the toe-pedal type valves at the front hot air outlets.

CABIN VENTILATION

In moderate temperatures, ventilation air can be obtained from the same outlets used for heating, by pushing the CABIN HEAT control full forward.

- 31 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

- 32 -

PITOT AND STATIC SYSTEM

Beechcraft V35B Bonanza

Pilot Operating Handbook

The pitot and static system provides a source of impact and static air for the operation of the altimeter, rate of climb and airspeed indicator. The pitot mast is located on the leading edge of the left wing. The static system provides a source of static air to the flight instruments through a flush static fitting on each side of the airplane fuselage.

Heating the Pitot element is essential. The heater switch is located on the switch panel on the pilot’s lower instrument panel.

VACUUM SYSTEM

Vacuum for air driven gyroscopic flight instruments and other air driven equipment is supplied by an engine driven vacuum pump. An adjustable relief valve controls suction by bleeding outside air into the vacuum pump. The relief valve and an oil separator, which removes oil from the air, are located on the forward side of the firewall.

A suction gauge indicates system vacuum in inches Hg. This instrument is located on the instrument panel; exact location may vary according to panel configuration. The vacuum should be maintained within 4-6 In.Hg. for proper operation of the air driven instruments.

STALL WARNING

To help prevent accidental stalls, a warning horn sounds as an incipient stall develops, while there is time for the pilot to correct the attitude. The horn, triggered by a sensing vane forward of the flap on the left wing, is effective in all flight attitudes and at all weights and airspeeds.

- 33 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

Performance

INTRODUCTION TO PERFORMANCE AND FLIGHT PLANNING

The graphs and tables in this section present performance information for flight planning at various parameters of weight, power, altitude and temperature. Examples have been presented on all performance graphs. In addition, the calculations for flight time, block speed and fuel required for a proposed flight are detailed below. All examples and calculations utilize the following conditions:

CONDITIONS At Denver:

Outside Air Temperature

Field Elevation

Altimeter Setting

Wind

15°C (59°F)

5330 ft

29.60 in. Hg

270° at 10 kts

10,010 ft Runway 26L length

Route of Trip

*DEN-V81-AMA

For VFR Cruise at 11, 500 feet

ROUTE

SEGMENT

DEN-COS

COS-PUB

MAGNETIC

COURSE

1610

1530

DIST NM

WIND

11500

FEET

DIR/KTS

010/30

OAT

11500

FEET °C

-5

ALT

SETTING

IN.HG

29.60

PUB-TBE

TBE-DHT

DHT-AMA

1340

1320

1250

At Amarillo:

Outside Air Temperature 25°C (77°F)

Field Elevation 3605 ft

100/20

200/20

29.56

Altimeter Setting

Wind

Runway 21 Length

29.56 in. Hg

180° at 10 kts

13,500 ft

To determine pressure altitude at origin and destination airports, add 100 feet to field elevation for each

.1 in. Hg below 29.92, and subtract 100 feet from field elevation for each .1 in. Hg above 29.92.

Pressure Altitude at DEN:

29.92 - 29.60 = .32 in. Hg

The pressure altitude at DEN is 320 feet above the field elevation.

5330 + 320 = 5650 ft

Pressure Altitude at AMA:

29.92 - 29.56 = .36 in. Hg

The pressure altitude at AMA is 360 feet above the field elevation.

3605 + 360 = 3965 ft

- 34 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

NOTE

For flight planning, the difference between cruise altitude and cruise pressure altitude has been ignored.

Calculations for flight time, block speed and fuel requirement:

Cruise Climb:

Enter the graph for CRUISE CLIMB at 15°C to 5,650 ft and to 2650 lbs. Enter at -5°C to 11,500 ft and to

2650 lbs. Read:

Time to Climb = (21.1 - 8) = 13.1 min

Fuel Used to Climb = (4 - 1.5) = 2.5 gal

Distance Traveled = (39 - 14) = 25 NM

The cruise power setting is assumed to be at 2050 rpm. Since cruise at 11,500 feet requires full throttle.

The manifold pressure and fuel flow may be read from either the cruise power setting table for 139 HP or 120 HP.

The temperatures for cruise are presented for a standard day (ISA); 20°C (36°F) above a standard day

(ISA + 20°C); and 20°C (36°F) below a standard day ((SA - 20°C). These should be used for flight planning. The IOAT values are true temperature values which have been adjusted for the compressibility effects IOAT should be used for setting cruise power while enroute.

Enter the graph for ISA conversion at 11,500 feet and the temperature for the route segment:

DEN-PUB

PUB- TBE OAT

OAT

ISA Condition

-5°C

ISA + 3°C

0°C

ISA + 8°C

TBE-DHT

DHT-AMA

OAT

ISA Condition

9°C

ISA + 8°C

10°C

ISA + 18°C

- 35 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

Enter the cruise power settings table for 139 HP (or full throttle) at 10,000 ft, 12,000 ft, ISA and ISA +

20°C.

TEMPERATURE ISA TEMPERATURE ISA + 20°C

ALTITUDE

FEET MAN

PRESS

FUEL

FLOW

PPH/GPH

TAS

KNOTS

MAN

PRESS

FUEL

FLOW

PPH/GPH

TAS

KNOTS

10,000 19.9 56.0/9.3 141 19.9 54.2/9.0 141

12,000 18.4 52.7/8.8 138 18.4 51.3/8.6 138

Interpolate for 11,500 feet and the temperature for the appropriate route segment. Results of the interpolations are:

ROUTE

SEGMENT

MAN

PRESS

FUEL

FLOW

PPH/GPH

TAS

KNOTS

DEN-PUB 18.8 53.3/8.9 139

PUB-TBE

TBE-DHT

18.8

52.9/8.8

52.2/8.7

139

DHT -AMA 18.8 52.2/8.7

NOTE

The preceding are exact values for the assumed conditions.

139

- 36 -

Time and fuel used were calculated as follows:

Time = Distance ÷ Ground Speed

Fuel Used = (Time) x (Fuel Flow)

Results are:

ROUTE

SEGMENT

DISTANCE

EST

GROUND

SPEED

KNOTS

TIME AT

CRUISE

ALTITUDE

HRS: MIN

FUEL

USED

FOR

CRUISE

GAL

DEN-COS *30 168 0:13 1.9

COS-PUB 40 167 0:14 2.1

PUB-TBE 74 125 0:35 5.1

TBE-DHT 87 128 0:41 5.9

DHT-AMA 65 131 0:30 4.4

"Distance required to climb has been subtracted from segment distance.

TIME - FUEL - DISTANCE

TIME

HRS: MINS

FUEL

GAL

DISTANCE

NM ITEM

Start, Runup,

Taxi and Take- off acceleration

0:05 1.4 0

Climb

Cruise

0:13

2:13

2.5

19.4

296

Beechcraft V35B Bonanza

Pilot Operating Handbook

Total 2:31 23.3 321

Total Flight Time: 2 hours, 31 minutes

Block Speed: (321 NM .;- 2 hours, 31 minutes) = 128 knots

Reserve Fuel (45 minutes at 83 HP)

Enter the cruise power settings table for 83 HP (or full throttle). The fuel flow for 83 HP is 7.1 gallons per hour.

Reserve fuel = (45 min) (7.1 GPH) = 5.3 gallons

Total Fuel = (23.3 + 5.3) = 28.6 gallons

- 37 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

The estimated landing weight is determined by subtracting the fuel required for the trip from the ramp weight:

Assumed ramp weight = 2660 lbs

Estimated fuel from DEN to AMA = (28.6 gal) (6Ibsjgal) = 171 lbs

Estimated landing weight = (2660 - 171) = 2489 lbs

Examples have been provided on the performance graphs. The above conditions have been used throughout. Rate of climb was determined for the initial cruise altitude conditions.

COMMENTS PERTINENT TO THE USE OF PERFORMANCE GRAPHS

The example, in addition to presenting an answer for a particular set of conditions, also presents the order in which the graphs should normally be used, Le., if the first item in the example is

OAT, then enter the graph at the known OAT.

The reference lines indicate where to begin following guide lines. Always project to the reference line first, and then follow the guide lines to the next known item.

Indicated airspeeds (IAS) were obtained by using the AIRSPEED CALIBRATION Graph.

The associated conditions define the specific conditions from which performance parameters have been determined. They are not intended to be used as instructions.

The full amount of usable fuel is available for all approved flight conditions.

- 38 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

- 39 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

- 40 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

- 41 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

- 42 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

- 43 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

- 44 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

- 45 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

- 46 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

- 47 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

- 48 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

- 49 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

Flight Sim Developers (FSD) EULA Agreement

FSD add-on software for Microsoft Flight Simulator.

IMPORTANT-READ CAREFULLY: BY INSTALLING THIS SOFTWARE YOU ARE AGREEING TO THE TERMS SPECIFIED BELOW!

This FSD End User License Agreement (" EULA ") is a legal agreement between you (either an individual or a single entity) and FSD, for the software product. " SOFTWARE PRODUCT " is hereby identified as, and includes, any or all computer software, associated media, printed materials, and "online" or electronic documentation associated with it. By installing, copying, or otherwise using the SOFTWARE PRODUCT, you agree to be bound by the terms of this EULA. If you do not agree to the terms of this EULA, do not install or use the SOFTWARE PRODUCT.

SOFTWARE PRODUCT LICENSE

The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The SOFTWARE PRODUCT is licensed, not sold. FSD maintains ownership of the software.

1. GRANT OF LICENSE .

Installation and usage

FSD grants to you the rights to install and use the software, for your own personal use only, on one (1) computer. Installation on a second computer or any number of additional computers is prohibited. The license may be transferred to another computer with permission from FSD provided you can demonstrate that the software has first been removed from the original computer. FSD can provide you with a utility which will remove all files and the license from the original computer and create a data file demonstrating this. You may inquire with FSD regarding this by contacting us in the manner described below under Contacting FSD . Other arrangements on subsequent to evaluation by FSD can also be made, and inquiries are welcome.

- Reproduction and Distribution.

You may NOT reproduce or distribute any number of copies of the SOFTWARE PRODUCT. Webmasters may NOT upload the SOFTWARE

PRODUCT to their web sites, or distribute the SOFTWARE PRODUCT in any way. At no time may the SOFTWARE PRODUCT be placed on a web site, newsgroup, Internet mailing list, or Bulletin Board (BBS), or copy/redistribute the software and documentation by any other means.

DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS.

-Limitations on Reverse Engineering, Decompilation, and Disassembly.

You may not reverse engineer, decompile, or disassemble the SOFTWARE PRODUCT.

- Use of "key generator" or other license "hacking" tools.

Use of any such utility or tool on your system, designed to circumvent the FSD license/license system for this or any other FSD aircraft shall be considered a violation of this agreement and cause for termination of this license agreement and all other FSD licenses.

- Separation of Components.

The SOFTWARE PRODUCT is licensed as a single product. Its component parts may not be separated for use on more than one computer.

- Software Transfer.

You may not transfer this license without the specific permission of FSD International.

- Termination.

Without prejudice to any other rights, FSD may terminate this EULA if you fail to comply with the terms and conditions of this EULA. In such event, you must destroy all copies of the SOFTWARE PRODUCT and all of its component parts.

- 50 -

Beechcraft V35B Bonanza

Pilot Operating Handbook

3. COPYRIGHT

All title and copyrights in and to the SOFTWARE PRODUCT (including but not limited to any images, photographs, animations, video, audio, music, text, and "applets" incorporated into the SOFTWARE PRODUCT) and any copies of the SOFTWARE PRODUCT are owned by FSD. The

SOFTWARE PRODUCT is protected by copyright laws and international treaty provisions. Therefore, you must treat the SOFTWARE PRODUCT like any other copyrighted material except that you may install the SOFTWARE PRODUCT on a single computer provided you keep the original solely for backup or archival purposes.

4. U.S. GOVERNMENT RESTRICTED RIGHTS

The SOFTWARE PRODUCT and documentation are provided with RESTRICTED RIGHTS. Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-

7013 or subparagraphs (c)(1) and (2) of the Commercial Computer Software-Restricted Rights at 48 CFR 52.227-19, as applicable.

Manufacturer is FSD International, Olathe, Kansas.

5 . MISCELLANEOUS

If you acquired this product in the United States, this EULA is governed by the laws of the State of Kansas.

If you acquired this product in Canada, this EULA is governed by the laws of the Province of Ontario, Canada. Each of the parties hereto irrevocably attorns to the jurisdiction of the courts of the Province of Ontario and further agrees to commence any litigation, which may arise hereunder in the courts located in the Judicial District of York, Province of Ontario.

If this product was acquired outside the United States, then local law may apply.

Should you have any questions concerning this EULA, or if you may do so in the manner described below under Contacting FSD

6 . LIMITED WARRANTY

NO WARRANTIES . FSD expressly disclaims any warranty for the SOFTWARE PRODUCT. The SOFTWARE PRODUCT and any related documentation is provided "as is" without warranty of any kind, either express or implied, including, without limitation, the implied warranties or merchantability, fitness for a particular purpose, or non infringement. The entire risk arising out of use or performance of the SOFTWARE

PRODUCT remains with you.

7 . NO LIABILITY FOR DAMAGES . In no event shall FSD be liable for any damages whatsoever (including, without limitation, damages for loss of business profits, business interruption, loss of business information, or any other pecuniary loss) arising out of the use of or inability to use this

FSD product, even if FSD has been advised of the possibility of such damages. Because some states /jurisdictions do not allow the exclusion or limitation of liability for consequential or incidental damages, the above limitation may not apply to you.

Any attempts to distribute or alter the files without permission of FSD will be considered an act of piracy and will be dealt with according to domestic, or as applicable, international law.

8. U.S. Government Restricted Rights . The Software is a "commercial item," as that term is defined at 48 C.F.R. 2.101 (OCT 1995), consisting of "commercial computer software" and "commercial computer software documentation," as such terms are used in 48 C.F.R. 12.212 (SEPT

1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227-7202-1 through 227-7202-4 (JUNE 1995), all U.S. Government End Users acquire the Software with only those rights set forth herein.

Contacting FSD . Please use our E-mail message terminal for support inquires. You can access it from our front page or from our Tech Support page. This will insure that your support request will go to the right place, and the information on the forms will provide us with the minimal information we need to assist you.

- 51 -