Quick Start Guide - Toshiba America Business Solutions

Quick Start Guide - Toshiba America Business Solutions
DIGITAL MULTIFUNCTIONAL SYSTEM
Quick Start Guide
BEFORE FIRST USE
NOTICE for users in the USA
BE SURE TO ASK YOUR AUTHORIZED TOSHIBA DEALER ABOUT THE WARRANTY THAT YOUR SELLING DEALER
EXTENDS TO YOU. In order to assure you, the end-user, of warranty protection, Toshiba extends a limited warranty to
each of its authorized dealers and, in turn, requires each of its authorized dealers to extend its own warranty to you on terms
that are no less favorable than those given to the dealer by Toshiba. You should be aware, however, that Toshiba does not
itself extend any warranties, either express or implied, directly to you, the end-user, and no one is authorized to make any
representations or warranties on behalf of Toshiba. Specifically, TOSHIBA DOES NOT EXTEND TO YOU, THE END-USER,
ANY EXPRESS WARRANTY OR ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR USE OR FITNESS
FOR ANY PARTICULAR PURPOSE IN CONNECTION WITH THE HARDWARE, SOFTWARE OR FIRMWARE EMBODIED
IN, OR USED IN CONJUNCTION WITH THIS PRODUCT. Toshiba is not responsible for any damages or loss, either direct,
incidental or consequential, which you, the end-user, may experience as a result of your purchase or use of the hardware,
software or firmware embodied in or used in conjunction with this Product. Your sole remedy, in the event that you encounter
any difficulties with this Product, is against the authorized dealer from which you purchased the Product.
e-STUDIO907/e-STUDIO1057/e-STUDIO1207 (DP-9077/DP-1057/DP-1207) Digital Multifunctional System
In the event that this authorized dealer does not honor its warranty commitments, please contact Toshiba America
Business Solutions, Inc., so that Toshiba can try to help assure complete satisfaction of all the warranty rights to which you
are entitled from the authorized dealer.
Toshiba America Business Solutions, Inc.
9740 Irvine Blvd.
Irvine, CA 92618
Each instruction also covers the optional units used with these products.
California Proposition 65 Warning: USA-California only
This Product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
Caution!
For complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
FOR YOUR RECORDS ...
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
This machine contains the software having modules developed by Independent JPEG Group.
Copyright© 1995-2007 Adobe Macromedia Software LLC. All rights reserved.
This product uses "InstantBoot" provided by IT Access Co., Ltd., Japan.
PostScript is a registered trademark of Adobe Systems Incorporated.
SOFTWARE LICENSE
The SOFTWARE LICENSE will appear when you install the software from the CD-ROM. By using all or any portion of the
software on the CD-ROM or in the machine, you are agreeing to be bound by the terms of the SOFTWARE LICENSE.
The explanations in this manual are based on American English and the North American version of the software.
Software for other countries and regions may vary slightly from the North American version.
• The explanations in this manual assume that you have a working knowledge of your Windows or Macintosh computer.
• For information on your operating system, please refer to your operating system manual or the online Help function.
• The explanations of screens and procedures in this manual are primarily for Windows Vista® in Windows®
environments. The screens may vary depending on the version of the operating system.
• Considerable care has been taken in preparing this manual. If you have any comments or concerns about
the manual, please contact your dealer or nearest TOSHIBA Service Department.
• This product has undergone strict quality control and inspection procedures. In the unlikely event that a
defect or other problem is discovered, please contact your dealer or nearest TOSHIBA Service Department.
• Aside from instances provided for by law, TOSHIBA is not responsible for failures occurring during the use
of the product or its options, or failures due to incorrect operation of the product and its options, or other
failures, or for any damage that occurs due to use of the product.
To protect against loss or theft, record and retain for reference the machine’s serial number located at the lower left corner
of the left side of the machine.
Model Number
Serial Number
Date of Purchase
Place of Purchase
Authorized TOSHIBA Printer
Service Department Number
Notice for Users in U.S.A.
EMC (this machine and peripheral devices)
„„ WARNING:
FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the
manufacturer could void the user’s authority to operate this equipment.
Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations.
Products that have earned the ENERGY STAR® are designed to protect the environment
through superior energy efficiency.
The products that meet the ENERGY STAR® guidelines carry the logo shown above.
The products without the logo may not meet the ENERGY STAR® guidelines.
„„ Warranty
While every effort has been made to make this document as accurate and helpful as possible, TOSHIBA TEC Corporation
makes no warranty of any kind with regard to its content. All information included herein is subject to change without notice.
TOSHIBA is not responsible for any loss or damages, direct or indirect, arising from or related to the use of this operation manual.
© Copyright TOSHIBA TEC Corporation 2014. All rights reserved. Reproduction, adaptation or translation without prior
written permission is prohibited, except as allowed under copyright laws.
3
OPERATION MANUALS AND HOW TO USE THEM
Quick Start Guide (this document)
Software Setup Guide (CD-PDF)
Features important safety notes, names of parts
and components, information about the power-on
procedure, operation overviews, information for people
who manage the machine, and information about other
aspects of this machine.
Read this section before using the machine for the first
time.
Explains how to install the various drivers needed when
using this machine as a printer or network scanner.
Refer to this document when using this machine from a
computer. The Software Setup Guide can be found on
the “Software CD-ROM”.
User's Manual (PC)
Operation Guide (Built-in)
Can be downloaded from the machine to a computer
and viewed. Refer to this document to learn more
about printer mode and settings mode, and to learn
about the details of each type of mode.
Can be viewed by touching the operation guide icon
on the machine’s touch panel. When you are using
this machine, use this document to see an overview
of a particular mode or when you are having trouble
operating the machine.
DIGITAL MULTIFUNCTIONAL SYSTEM
Software Setup Guide
Downloading the User's Manual
You can download the [User's Manual] by following the procedures below while the machine is connected to the network.
1Confirm the machine’s IP address
First, tap the [Settings] key on the home screen, and then tap [System Settings] → [List
Print (User)] in the left menu.
Next, tap the [Print] key in the [All Custom Setting List], and confirm the IP address in
the printed list.
2Insert the machine’s IP address into the
3Download the [User's Manual]
Click [Operation Guide Download] on the displayed page. Next, select the desired
language from the “Language to download” list, and then click the [Download] button.
4Double-click on the downloaded file to display the User's Manual.
address bar of your web browser to access
the machine.
http://machine’s IP address/
User verification may be required depending on the
machine’s settings.
Please check with the machine’s administrator
to obtain the account information necessary for
verification.
"BATTERY DISPOSAL"
THIS PRODUCT CONTAINS A LITHIUM PRIMARY MEMORY BACK-UP BATTERY THAT MUST BE DISPOSED
OF PROPERLY. PLEASE CONTACT YOUR LOCAL DEALER OR AUTHORIZED SERVICE REPRESENTATIVE
FOR ASSISTANCE IN DISPOSING OF THIS BATTERY.
This product utilizes a CR coin Lithium battery which contains a Perchlorate material. Special handling for this
material may apply, California residents,
See www.dtsc.ca.gov/hazardouswaste/perchlorate/
Others, consult local environmental officers.
4
CAUTIONS
Symbols in this manual
WARNING
To ensure safe use of the machine, this manual uses various safety symbols. The safety symbols are
classified as explained below. Be sure you understand the meaning of the symbols when reading the manual.
Meaning of the symbols
CAUTION!
HOT
PINCH POINT
KEEP CLEAR
PROHIBITED
ACTIONS
Indicates a risk of death or serious injury.
DO NOT
DISASSEMBLE
MANDATORY
ACTIONS
CAUTION
Indicates a risk of human injury or property
damage.
Handling precautions
WARNING
If you notice smoke, a strange odor, or other abnormality, do not use the machine.
If used in this condition, fire or electrical shock may result.
Immediately switch off the main power and remove the power plug from the power outlet.
Contact your dealer or nearest TOSHIBA Service Department.
Do not use a flammable spray to clean the machine.
If gas from the spray comes in contact with hot electrical components or the fusing unit inside the machine, fire or
electrical shock may result.
Do not make any modifications to this machine.
Doing so may result in personal injury or damage to the machine.
Do not look directly at the light source.
Doing so may damage your eyes.
Do not block the ventilation ports on the machine. Do not install the machine in a location that will block
the ventilation ports.
Blocking the ventilation ports will cause heat to build up in the machine, creating a risk of fire.
The fusing unit and paper exit area are hot. When removing a misfeed, do not touch
the fusing unit and paper exit area. Take care not to burn yourself.
Do not remove the machine casing.
High-voltage parts inside the machine may cause electrical shock.
Do not place a container of water or other liquid, or a metal object that might fall inside, on the machine.
If the liquid spills or the object falls into the machine, fire or electrical shock may result.
If a thunder storm begins, switch off the main power and remove the power plug from the outlet to
prevent electrical shock and fire due to lightning.
When loading paper, removing a misfeed, performing maintenance,
closing the front and side covers, and inserting and removing trays, take
care that your fingers are not pinched.
The machine includes the document filing function, which stores document image data on the machine's hard drive. Stored documents can be called up and printed or transmitted as needed. If a hard drive failure occurs, it will no longer be possible to call
up the stored document data. To prevent the loss of important documents in the unlikely event of a hard drive failure, keep the originals of important documents or store the original data elsewhere.
With the exception of instances provided for by law, TOSHIBA TEC Corporation bears no responsibility for any damages or loss due to the loss of stored document data.
Laser information
Wave length
788 nm +12nm / -13nm
Pulse times
e-STUDIO907:
Normal paper mode (P/S = 420 mm/s) = 4.786 µs ± 0.020 µs / 7mm
Heavy paper mode (P/S = 420 mm/s) = 4.786 µs ± 0.020 µs / 7 mm
e-STUDIO1057/1207:
Normal paper mode (P/S = 580 mm/s) = 3.470 µs ± 0.014 µs / 7 mm
Heavy paper mode (P/S = 580 mm/s) = 3.470 µs ± 0.014 µs / 7 mm
Output power
Max 2.5 mW (LD1+LD2+LD3+LD4)
„„ Caution
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous
radiation exposure.
This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition 2-2007)
„„ SAFETY PRECAUTIONS
This Digital Equipment is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This
means that the equipment does not produce hazardous laser radiation. For your safety, observe the precautions below.
• Do not remove the cabinet, operation panel or any other covers.
• The equipment’s exterior covers contain several safety interlock switches. Do not bypass any safety interlock by
inserting wedges or other items into switch slots.
5
CAUTIONS
Power notes
WARNING
Do not insert or remove the power plug with wet hands.
If you will not use the machine for a long time, be sure to remove the power plug from the outlet for
safety.
This may cause electrical shock.
When removing the power plug from the outlet, do not pull on the cord.
Be sure to connect the power cord only to a power outlet that meets the specified voltage and current
requirements.
Also make certain the outlet is properly grounded. Do not use an extension cord or adapter to connect other devices to
the power outlet used by the machine. Using an improper power supply may cause fire or electrical shock.
* For
the power supply requirements, see the name plate in the lower left corner of the left side of the machine.
Pulling on the cord may cause damage such as wire exposure and breakage,
and may result in fire or electrical shock.
Installation notes
WARNING
Do not install the machine in a location with poor air circulation.
A small amount of ozone is created inside the machine during printing. The amount of ozone created is not
sufficient to be harmful; however, an unpleasant odor may be noticed during large copy runs, and thus the
machine should be installed in a room with a ventilation fan or windows that provide sufficient air circulation. (The
odor may occasionally cause headaches.)
Do not install the machine on an unstable or slanted surface. Install the machine on a surface that can
withstand the weight of the machine.
Risk of injury due to the machine falling or toppling.
Be sure to connect the power cord only to a power outlet that meets the specified voltage and current
requirements. Also make certain the outlet is properly grounded. Do not use an extension cord or adapter
to connect other devices to the power outlet used by the machine. Using an improper power supply may
cause fire or electrical shock.
Locations exposed to direct sunlight
Plastic parts may become deformed and dirty output may result.
Locations with ammonia gas
Installing the machine next to a diazo copy machine may cause dirty output.
* For the power supply requirements, see the name plate of each machines and devices.
Near a wall
Be sure to leave the clearances shown right between the unit and the nearest
wall or other surface.
For easy maintenance, you should also leave the clearances shown right around
the unit.
Locations subject to vibration.
Vibration may cause failure.
30cm
30cm
45cm
CAUTION
Locations that are excessively hot, cold, humid, or dry. (near heaters, humidifiers, air conditioners, etc.)
The paper will become damp and condensation may form inside the machine, causing misfeeds and dirty output.
The machine includes a built-in hard drive. Do not subject the machine to shock or vibration. In particular,
never move the machine while the power is on.
• The machine should be installed near an accessible power outlet for easy connection.
• Connect the machine to a power outlet which is not used for other electric appliances. If a lighting
fixture is connected to the same outlet, the light may flicker.
About consumables
WARNING
Do not throw a toner cartridge into a fire.
Store a toner cartridge out of the reach of children.
Toner may fly and cause burns.
6
NAMES OF PARTS AND POWER INPUT
The machine has two power switches: The main power switch inside the front cover located in the lower left corner, and the [Power] button (
) on the operation panel.
Turning on the power
[Power] button
• Turn the main power switch to the " " position.
• After the main power indicator lights up green, press the [Power]
button ( ).
Status Indicator *
Turning off the power
Turn off the power by pressing the [Power] button (
power switch to the "
" position.
), then turn the main
Restarting the machine
In order for some settings to take effect, the machine must be restarted.
Follow the message displayed on the touch panel to restart the system
(turn off the power by pressing the [Power] button (
again to turn the power back on).
Main power indicator
USB connector (A type)
Operation panel
Automatic document feeder
Keyboard
Toner tray
Front cover
Bypass-tray *
Tray 5 (MX-LC12) *
) and then press it
Tray 2
Tray 3
Tray 4
Caution:
Tray 1
• When turning off the main power switch, make sure that all indicators other than the
main power are turned off.
• In the case of a sudden main power outage, turn the power for the machine back on
and then turn it off in the correct order. If you turn off the main power switch or unplug
the power cord while the indicator is lit up or blinking, the hard disk drive may be damaged or data may be lost.
• Turn off both the [Power] button ( ) and the main power switch and unplug the power
cord if you suspect a machine failure, if there is a bad thunderstorm nearby, or before
you move the machine.
Curl Correction Unit *
Saddle finisher
*
*
Optional
Main power switch
In some machine operating states, restarting using the [Power] button ( ) may not
make the settings take effect. In this case, turn off the main power switch and then
turn it on again.
• When you change a toner cartridge while the keyboard is installed, be sure to store it in
the operation panel unit. If a toner cartridge is changed while the keyboard is pulled out,
the cartridge may come in contact with the keyboard and cause damage.
7
HOME SCREEN
This screen appears first. When you touch an icon, the corresponding screen appears.
Pressing the [Home Screen] button ( ) on the operation panel also displays this screen.
* The screen may differ from the actual one depending on the model or customization.
Copy
The scanned document is printed.
E-mail
A scanned document is attached to an e-mail and sent.
FTP
The scanned document is sent to the specified FTP
server directory or the specified folder in a computer
connected to the network.
Network Folder
The scanned document is sent to the computer network
folder specified in the Windows network.
HDD File retrieve
The scanned document is saved on the
hard disk drive of the machine or an
external memory device.
This icon can also be tapped to edit or
operate the stored data.
Action panel
Tap an item to edit Home
Screen or other operation.
Scrolling area
Up to 12 icons are displayed.
You can view hidden icons by scrolling
the screen horizontally.
Fixed area
Up to 10 icons are always displayed.
Operation Guide
See this document when you need help to
use the machine.
Settings
In setting mode, various settings can be configured to suit
the aims and needs of your application.
Job Status
Tap this icon to check the status of the job currently
being executed.
Page switch keys
Use these keys to view a hidden page in the scrolling area.
Operating the touch panel
In addition to the conventional method of single tapping, the touch panel of the machine can be operated by long touching, flicking and sliding.
Tapping

Double
tapping
Touch and then quickly release the finger.
Use this method to select a key, tab or
checkbox.

Long touching Touch the key with your finger and hold it for
a while.

Flicking

Lightly tap the touch panel twice. Use this
method to switch preview modes or enlarge a
preview image.
Flick the panel to scroll a preview image.
Dragging

Sliding

Drag (slide your finger touching the panel
in a random direction) to replace or delete
pages in the original displayed on the preview
screen.
Slide the scroll bar (with your finger touching
the panel) to scroll up and down a list
containing a large number of items.
8
PRINTER
Basic printing
�In a Windows environment
This section explains how to print a document from "WordPad", which is a standard accessory application in Windows.
1 Select [Print] from the [File]
2Select the printer driver for
menu
the machine and click the
[Preferences] button
3Click the [Paper] tab and select
4Click the [OK] button to
the paper size
start printing




*Make sure the paper size is the same
as the paper size set in the application.
�For Mac OS X environments
The following example explains how to print a document from the standard accessory application "TextEdit" in Mac OS X.
1Select [Page Setup] from
the [File] menu and select
the printer

2Configure paper and click
the [OK] button

3Select [Print] from the [File] menu.
Make sure that the correct printer is
selected.
4Print
settings
5 Click the [Print]
button to start
printing

• Different types of paper sheets can be inserted for covers, etc.
• For Windows environments, different paper can be inserted into the specified
page, or the paper can be inserted as inserts.
9
COPY
Basic operations
1Place the
2Copy settings
original
3Preview
4Set the
5Start
number of
copies

1 Copy settings
2 Displays the [Function Review] dialog
3 Scans the original and displays it in the preview area (if preview is required)
4 Cancels all settings
Corrects the number
of copies
Copy settings
Paper Select
Auto
Paper Select
8 12 X11
Plain
3
8 12 X11
Plain
4
8 12 X11
Plain
2
8 12 X11
Plain
Off
Output
Output
Type and Size
Bypass Tray (Optional)
Specify the type and size of paper.
Middle
tray
Large Capacity Tray (Optional)
Offset
Tray
Outputs to the middle tray of the machine
100%
Displays the basic ratio menu.
Zoom
Displays the XY Zoom ratio menu.
XY Zoom
Auto Image
5
8 12 X11
Plain
Sort
2-Sided Copy
1-Sided->1-Sided
2-sided copy
Group
Separator
Page
1-Sided->1-Sided
1-sided copy
1-Sided->2-Sided
Outputs two 1-Side original sheets to one
2-Side sheet
Top Tray
2-Sided->2-Sided
Outputs one 2-Side original sheet to one
2-Side sheet
Stacker Tray
2-Sided->1-Sided
Outputs one 2-Side original sheet to two
1-Side sheets
Outputs to the offset tray of the finisher
11x17->8 1/2x11
8 1/2x11->5 1/2x8 1/2
8 1/2x14->11x17
77%
Outputs by sorting on a set basis
Outputs by sorting on a page basis
Inserts separator pages for every specified
number of copies
Outputs into the top tray (option)
Outputs into the stacker tray (option)
129%
11x17->8 1/2x14
8 1/2x14->8 1/2x11
100
Automatically sets the ratio based on the
original settings and paper settings.
121%
64%
Large Capacity Tray
Copy Ratio
Copy Ratio
Tray 1/Tray 2/Tray 3/Tray 4
Bypass Tray
8 12X11
Plain
Multi Shot
Copying a multi-page original to a single sheet
Paper Tray
1
Multi Shot
Sets the ratio based on the original
settings and paper settings.
8 1/2x11->11x17
5 1/2x8 1/2->8 1/2x11
( 25㨪200 )
%
Other Ratio
by Paper
by Size
Enlarges or reduces the image in increments
or decrements of 1%
Transits to the "Other Ratio" screen
Transits to the "by Paper" screen
Transits to the "by Size" screen
10
Exposure
Exposure
Auto
Auto 8 12 x11
Selects automatically
Photo
Best for photo originals
Text
Best for text originals
Map
Best for maps containing fine text
Text/Printed Photo
Prioritizes the quality of text and printed photo
images
Light Original
Best for faint colored originals such as those
written using pencil
Text/Photo
Best for text originals to which photos are
pasted
Printed Photo
Prioritizes the quality of photo images
Auto
Original
Original
1
.
.
.
3
.
.
.
5
Tap a darker or lighter area to adjust shading
Auto
Selects automatically
Inch
Displays inch size list
AB
Displays AB size list
Direct Entry
Displays the direct entry screen
Custom Size
Displays the custom size list
51/2×81/2
81/2×11
81/2×13
11×17
Inch
51/2 x 81/2 R
81/2 x 11R
81/2×14
AB
A5
A5R
B5
B5R
A4
A4R
B4
A3
216 × 340
216×343
81/2×132/5
Others
Others
Margin Shift
Adds margins
Erase
Specify the edge erase (center erase) and erase width
of the original for copies
Pamphlet Copy
Arranges a pamphlet format
Covers/Inserts
Inserts cover or insertion sheets
Transparency
Inserts
Outputs transparency films in a way that they do not
stick together
Blank Page
Skip
Skipping blank pages in an original
Card Shot
Copies both sides of a card as a single page
Position Image
Specify the image print position
Tab Copy
Copies captions onto tab paper
Dual Page
Copy
Copies each facing page
Book Copy
Copies a pamphlet
Book Divide
Splits a pamphlet original by page in a copy
Stamp
Prints dates, the number of pages, and stamps
Custom Image
Adds a registered image to an original
Hidden Pattern
Print
Padding unauthorized copy deterrent data
Repeat Layout
Repeats the same image on one sheet in a copy
Multi-Page
Enlargement
Making a poster-sized copy
Mirror
Image
Inverts the original into a mirror image
Full Bleed Copy
Copies originals with no edge cut-off
Centering
Copying in the center of the paper
B/W Reverse
Reverses white and black
Job Build
Copies many originals at once
Tandem Copy
Using two machines to copy in parallel
Original
Count
Check the number of scanned document sheets
Reverse Order
Copies originals in reverse order
Mixed Size
Original
Copies originals of different sizes together
Slow Scan Mode
This mode switches document feeder controls for
originals with thin paper thickness
Sharpness
Adjust the sharpness of an image
Scan
Resolution
Specify the resolution of the original
Suppress
Background
Suppresses light background area in copies
Toner Save
Mode
Reduces toner consumption during copying *
File
Uses document filingdrive of the machine
Quick File
Temporarily saves the scanned data on the hard
disk drive of the machine
* Items may not be displayed depending on the machine settings.
COPY
11
SCAN
Basic Operations (Scan to E-mail)
1Place the
2Scan settings
original
3Preview
4Specify the destination
5Start
1 Scan settings
2 Displays the [Function Review] dialog
3 Scans the original and displays it in the preview area (if preview is required)
4 Cancels all settings
Scan settings
Address Book
Address Book
To
Touch to input
Address
Touch to input Address
Tap this to display the address book screen to select a destination.
1
Tap this to switch between To and Cc.
File Name
File Name
Select a file name or enter it directly.
Subject
Subject
.
.
.
3
Exposure
Selects automatically
.
.
.
5
Touch a darker or lighter area to adjust shading
Resolution
200x200dpi
Searches a destination
Auto
Auto
Enter an address directory.
To
Exposure
Resolution
100x100dpi
300x300dpi
150x150dpi
400x400dpi
200x200dpi
600x600dpi
100 x 100 dpi
150 x 150 dpi
200 x 200 dpi
300 x 300 dpi
400 x 400 dpi
600 x 600 dpi
Text
Best for text originals
Text/Printed Photo
Prioritizes the quality of text and printed photo
images
Text/Photo
Best for text originals to which photos are
pasted
Printed Photo
Prioritizes the quality of photo images
Photo
Best for photo originals
Map
Best for maps containing fine text
Select a subject or enter it directly.
12
File Format
File Format
PDF
This function sets the file format and compression mode (ratio) of send data.
File format
Compression mode
Color/Grayscale
TIFF
B/W
Transmittable formats:
TIFF, XPS, JPEG, PDF, PDF/A
Low
Transmittable formats:
TIFF, XPS, PDF, PDF/A
Middle
XPS
PDF/A
Creates an
encrypted PDF
file
Encry.
Creates an
encrypted PDF
file
SCAN
Sends data by reducing
its size
U-Fine
Sends data by reducing
its size but without
reducing the image
quality
None
MH (G3)
MMR (G4)
Others
Compact
Bk Letter Emphasis
Encry.
B/W
Color/Grayscale/Black & white
Compressible modes:
Compressible modes:
None, MH (G3), MMR
Low, Medium, High, Bk Letter Emphasis
(G4)
High
JPEG
PDF
Number of pages setting
Color/Grayscale
Specified Pages per File
( 1㨪99 )
Page
Specify the number
of pages per file
Displays the number
of pages per file
Increases or
decreases the
number of pages per
file
Others
Job Build
Tap this to switch the job build mode on or off.
Setting it to On scans a large number of originals
in segments.
Slow Scan Mode
Scans a thin original
Mixed Size
Original
Scans originals of different sizes together
Original
Count
Tap this to switch the original count setting on or
off.
Setting it to On checks the scanned number of
original sheets.
Erase
Specify the edge erase (center erase) and erase
width of the original to be sent
Dual Page Scan
Scans an original as two separate pages
Book Divide
Sends a pamphlet original by splitting it by page
Card Shot
Sends both sides of a card as a single page
Timer
Automatically performs transmission at the
specified time
Verif.
Stamp
Stamps scanned documents
Suppress
Background
Scans originals by suppressing light background area
Blank Page
Skip
Erases blank pages mixed in an original after
scanning
Drop Out
Color
Removes chromatic colors from the scanned
document before transmission
Sharpness
Adjust the sharpness of an image to produce a
sharper or softer image.
Contrast
Adding contrast to the scanned document before
transmission.
File
Saves the send data on the hard disk drive of
the machine.
Quick File
Temporarily saves the send data on the hard disk
drive of the machine
13
DOCUMENT FILING
This function saves the original scanned on the machine or print data from a PC on the hard disk drive of the machine or on an external memory device.
The saved data can be printed or sent. Editing of the stored files, for example combining, is also possible.
Basic operations
1HOME SCREEN
2Select the folder
3Place the original
4Start
Folder select screen
My Folder
Main Folder
Use this to save the original you wish to
share among users.
Displays the private screen for the
login user.
Quick File Folder
Custom Folder
Saves files temporarily.
The folder for the registered user.
Reset button
Use this button to reset all settings.
HDD Status
The usage of the machine's hard disk
drive is displayed in graphical format,
separately for Main Folder, Custom
Folder, and Quick File Folder.
• Files stored using [Quick File] are provided with the "Sharing" property that can be
accessed by any person for output and sending. Therefore, do not store sensitive
documents or documents that you do not want to be used by others using the [Quick
File] function.
14
File list view
File thumbnails view
You can select the method to display files. List view or thumbnails view can be selected.
�Viewing by folder
�Viewing by job
Job settings menu
Select a file you wish to retrieve, then select a desired operation. The following operations are displayed on the action panel.
The [Print Now] operation is not displayed on the action panel but displayed as a button in the trigger area.
Choose Print Settings
Prints a file from the reprint screen
This item changes to [Print] when multiple files are selected.
Send
Sends a file from the resend screen
This item is not displayed when multiple files are selected.
Move
Moves a file
You can also edit the file name using this option.
Combine File
Merges the selected two files into a single file
This item is not displayed when only one file or three or more files are selected.
Check Image
Check the content of the original file by image
This item is not displayed when multiple files are selected.
DOCUMENT FILING
See Detail Information
Print and Delete
the Data
Views property change and file detail information
This item is not displayed when multiple files are selected.
Select this item if you wish to delete data after printing.
Prints the selected file immediately
Delete
Deletes data
15
COPY OUTPUT
Configure the output settings for copies using Sort, Group, Offset, Staple, Punch, or Fold.
Basic operations
1Select [Output]
2Copy output settings
3Check the preview image
4Start
1 Specify the output tray
2 Select the output and paper output type
3 Specify the details of output mode
Output tray settings
Output tray settings
Specify the destination to output copies.
The output tray currently selected is indicated by an arrow.
(When a finisher (50-sheet stapling) or saddle finisher (50-sheet
stapling) is installed)
The [Top Tray] key can be selected.
(When a finisher (100-sheet stapling) or saddle finisher
(100-sheet stapling) is installed)
The [Middle Tray] key can be selected.
When a large capacity stacker is installed
You can select the [Top Tray] key or [Stacker Tray] key.
Offset
Tray
Separator
Page
Outputs to the offset tray
Separator Function
You can insert separator pages for every specified number of
copies or before or after each job.
Sort/Group function
This function sets the sorting method when copying a scanned
document.
Sort staple
This function staples the output copies and deliver them to the tray.
Sort
Sorts the scanned document on a set basis,
and outputs them
1 staple in back
Group
Groups the scanned document on a page
basis, and outputs them.
1 staple in front
2 Staples
Offset
Offset function
Select this function when you wish to output copies while shifting
them set by set.
Selecting the staple function clears the Offset checkmark
automatically.
Saddle
Stitch
Slant
Staple
Copies can be folded at the center, stapled,
and output.
This function is only available when a saddle
finisher is installed.
Enables slant stapling.
This function is available when [1 Staple at
Back] is selected while a finisher (50-sheet
stapling) or saddle finisher (50-sheet stapling)
is installed.
16
Saddle Stitch
Saddle
Stitch
(When a saddle finisher is installed)
Copies can be folded at the center, stapled, and output.
(When a trimming module is installed on the saddle finisher)
For saddle folding, it trims a side drop, offering a good-looking output
image.
Off
Releases saddle stitch
Left Binding
This selects left binding
Right Binding
Cover Setting
Tap this to switch the cover setting Off or On, or to
configure the paper tray settings.
(When a trimming module is installed on the saddle finisher)
Enabling "Saddle Stitch" allows you to configure the trimmer
settings.
Scans 1-Sided originals
1-Sided
Off
Turns off the trimmer setting
On
Turns on the trimmer setting
2
( 2.0㨪20.0 )
mm
0
Saddle
Fold
Selects saddle fold
Z-Fold
Selects Z-fold
Inside
Outside
Fold Multiple Sheets Together
Original Image
Selects accordion fold
Double
Fold
Selects double fold
Selects half fold
Folds paper so that the print side faces downward
during output
Folds paper so that the print side faces upward
during output
Select this option to fold multiple sheets together
A3
B4
A4R
11 X17
812 X14
812 X11R
Open Left
Select the size of paper to be folded with
Z-fold
(One of either 11" x 17", 8-1/2" x 14", 8-1/2"
x 11"R, A3, B4 and A4R can be selected)
Folds paper for left binding during output
Output Image
Displays a folding image
Selects C-fold
Accordion Fold
Specify the trimming width
within the range of 2.0 to
20.0 mm
Detail setting screen for each folding type
(When a saddle finisher or folding unit is installed)
Copies can be folded and output.
Half
Fold
Scanning 2-Sided originals
2-Sided
This selects right binding
Folding function
C-Fold
Trimmer Setting
Trimmer
Setting
Open Right
Folds paper for right binding during output
Punch function
(When a punch module is installed)
This function punches copies and outputs them. It is available for paper sizes 8-1/2"x11"R to 11"x17".
2 Hole Punch
Punches holes during output
3 Hole Punch
COPY OUTPUT
17
MANUAL FINISHING
This function allows you to set for finish on copied or printed pages.
You can select the manual finishing mode if the inserter is installed.
When the finisher, saddle finisher, punch module, or folding unit is installed, finishing operations, such as stapling, punching or folding, can be performed.
Basic operations
1Place the original
2Switch to the manual finishing
mode
�Changing modes from the Home
Screen
3Finishing method settings
4Start
�Changing modes from the screen
for each mode
1 Select the appropriate finishing method
2 Change the paper tray or output tray as
required
Adjust the inserter tray guide to the paper size, and load paper.
(Special media such as transparency
film and tab paper cannot be used.)
Paper Loading and Output Settings
Plain
Upper
Tray
8 12 x11
Plain
Lower
Tray
8 12 x11
Checking and changing
the output tray
You can check the type and size of paper loaded.
As needed, the paper type and size can be specified for each of the
upper and lower trays.
If you wish to change the paper sizes or types, select [System
Settings] > [Paper Tray Settings] > [Inserter].
Plain
8 x11
1
2
Check the paper type and size
Upper
Tray
Selects the upper tray as paper tray
Lower
Tray
Selects the lower tray as paper tray
Middle
tray
Offset
Tray
Checking and changing
the output tray
The output tray is automatically selected based on the output
function you set. If Z-Fold, Half Fold, or Punch is selected, however,
you can select the middle or offset tray for the output tray.
If you have changed the output tray, the output function may be
deselected depending on the original output settings.
Middle
tray
Selects the middle tray as the output tray
Offset
Tray
Selects the offset tray as the output tray
Orientation of placed original
For stapling or punching on the desired position,
place the paper as shown in the following:
• For staple function, place the paper face up and
align text with the direction of the touch panel
display. (For the saddle stitch function, place the
paper so that middle surface faces up.
• When using punch or folding function, place the paper face up, and align text horizontally and upward
with the scan (right) direction.
18
Staple
(When a finisher installed)
This function staples the loaded paper sheets into a sheaf.
1 staple in back
1 staple in front
2 Staples
Setting the number of
copies (number of pages)
Copies/Pages
This function loads previously sorted sheets and outputs multiple
sets at once.
Number of copies setting
1
(1-999)
Enter the number of output copies
(from 1 to 999)
Number of pages setting
All Pages
Folding function
(When a saddle finisher is installed)
This function staples each set of copies at two positions in the
center of paper, folds them in half, and outputs them.
(When a trimming module is installed on the saddle finisher)
For saddle stitch, it trims a side drop, offering a good-looking output
image.
(When a folding unit is installed)
This function folds paper in Z-fold, C-fold, or other types of shapes.
(When a saddle finisher is installed)
Paper can be folded in a saddle fold.
*
The paper sizes that can be selected vary depending on the type
of paper fold.
*
Special media such as transparency film and tab paper cannot be
used.
Saddle
Stitch
Trimmer
Setting
Middle
tray
Offset
Tray
Staples each set of copies at two positions
in the center of paper, and folds them in half
during output
Trims a side drop for saddle folding during
output
Specify the trimming width within the range of
2.0 to 20.0 mm
Checking and changing
the output tray
The output tray is automatically selected based on the output
function you set. If Z-Fold, Half Fold, or Punch is selected, however,
you can select the middle or offset tray for the output tray.
If you have changed the output tray, the output function may be
deselected depending on the original output settings.
Middle
tray
Selects the middle tray as the output tray
Offset
Tray
Selects the offset tray as the output tray
Saddle
Fold
Z-Fold
C-Fold
Accordion Fold
Double
Fold
Select this to set all pages as one set
*
If this setting is enabled, set the [Number
of Copies] to "1".
Half
Fold
Allowable paper sizes:
12"x18", 11"x17", 8-1/2"x14", 8-1/2"x11"R, 8K,
A3W, A3, B4, A4R, SRA3
The fold settings can be configured in [Detail].
B5R can be used only in a saddle finisher
(50-sheet stapling).
Allowable paper sizes:
11"x17", 8-1/2"x14", 8-1/2"x11"R, A3, B4, A4R
This function can be used with the staple and
punch functions if a folding unit is installed in a
finisher (100-sheet stapling) or saddle finisher
(100-sheet stapling) while the paper size is 11”
x 17”, or A3, B4.
Allowable paper sizes:
8-1/2”x11”R, A4R
Allowable paper sizes:
8-1/2”x11”R, A4R
Allowable paper sizes:
8-1/2”x11”R, A4R
Allowable paper sizes:
8-1/2”x11”R, A4R
Select this to specify the number of page for
each set
Manual
1
Saddle Stitch
(1-200)
Enter a numeric value when [Manual] is
selected.
(from 1 to 200 pages)
Punch function
(When a punch module is installed)
This function punches holes in paper. It is available for paper sizes 8-1/2"x11"R to 11"x17".
You cannot use 12" x 18" (A3W) size paper, and special media such as transparency film.
2 Hole Punch
Punches holes during output
This function can be used with the Z-Fold function if a folding unit is attached to a finisher (100-sheet stapling) or saddle
finisher (100-sheet stapling) while the paper size is 11” x 17”, or A3, B4.
3 Hole Punch
MANUAL FINISHING
19
SPECIFICATIONS
Basic Specifications / Copier specifications
Name
e-STUDIO907/e-STUDIO1057/e-STUDIO1207
Type
Console
Color
Monochrome
Copier system
Laser electrostatic copier
Resolution
Read: 600 × 600 dpi, 600 × 400 dpi, 600 × 300 dpi
Write: 600 × 600 dpi, 1,200 × 1,200dpi
Gradation
Read: equivalent to 256 levels / Write: equivalent to 256 levels
Original paper
sizes
Max. 11" × 17” (A3) for sheets and bound documents
Copy sizes
12" × 18" (A3 wide) to 5-1/2" × 8-1/2"R, A5R, Transparency film, Heavy paper
Tray 1: 8-1/2" x 11", A4, B5
Tray 2: 8-1/2" × 11", A4
Tray 3: 12" × 18" (A3 wide), 11" × 17", 8-1/2" × 14", 8-1/2" × 13-1/2", 8-1/2" × 13-2/5", 8-1/2" × 13",
8-1/2" × 11", 8-1/2" × 11"R, 7-1/4 × 10-1/2"R, A3, B4, A4W, A4, A4R, B5, B5R
Tray 4: 12" × 18" (A3 wide), 11" × 17", 8-1/2" × 14", 8-1/2" × 13-1/2", 8-1/2" × 13-2/5", 8-1/2" × 13",
8-1/2" × 11", 8-1/2" × 11"R, 7-1/4 × 10-1/2"R, 5-1/2" × 8-1/2"R, A3, B4, A4W, A4, A4R, B5, B5R, A5R
Warm-up time
210 seconds
 This may vary depending on the ambient conditions.
First-copy time
e-STUDIO907:
4.0 seconds
e-STUDIO1057:
3.2 seconds
e-STUDIO1207:
3.2 seconds
 This may vary depending on the state of the machine.
 Portrait feeding of 8-1/2" x 11" (A4) sheets.
Continuous
copying speeds*
(when shifter is
not in operation)
e-STUDIO907e-STUDIO1057 e-STUDIO1207
8-1/2" × 11", A4, B5:
90 copies/min. 105 copies/min.
120 copies/min.
8-1/2" × 11"R, 7-1/4" × 10-1/2"R, A4R, B5R: 58 copies/min.
67 copies/min.
76 copies/min.
8-1/2" × 14", B4:
50 copies/min.
58 copies/min.
66 copies/min.
11" × 17", A3:
47 copies/min.
52 copies/min.
54 copies/min.
*C
ontinuous speed for same original source. Output may be temporarily interrupted to stabilize
image quality.
Copy ratios
Same size: 1:1 ± 0.8 % Enlarge: 121 %, 129 %, 200 %, 400 %
Reduce: 25 %, 50 %, 64 %, 77 %
Zoom range: 25 to 400 % (25 - 200 % using DSPF) in 1 % increments, total 376
increments. Can calculate zoom rate when mm is specified.
Useable paper
Tray 1: 16 lbs bond to 28 lbs bond (60 to105 g/m2)
Tray 2: 16 lbs bond to 28 lbs bond (60 to105 g/m2)
Tray 3: 16 lbs bond to 80 lbs cover (60 to 220 g/m2)
Tray 4: 16 lbs bond to 80 lbs cover (60 to 220 g/m2)
Paper feed / capacity
1,200 plus 800 plus 500 plus 500 ( = 3,000) sheets in 4 trays
sing 21 lbs (80 g/m2) weight paper
U
Max. paper feed / max. capacity
1,200 plus 800 plus 500 plus 500 ( = 3,000) sheets in 4 trays plus 500-sheet
multi-bypass tray plus 5,000 sheets in large capacity trays plus 5,000 sheets in
large capacity trays (total 13,500 sheets)
2
 Using 21 lbs (80 g/m ) weight paper
Continuous copy
Max. 9,999 copies
Memory
Standard: 5 GB HDD: 1 TB SD card: 4GB
 1 GB = One billion bytes when referring to hard drive capacity. Actual format
capacity is less.
Ambient environment
Operating environment
54 °F (10 °C) to 91 °F (35 °C) (20 % to 85 % RH) (Humidity is 60% or
below while the temperature is 91°F (35°C), and the temperature is 86°F
(30°C) or below while the humidity is more than 85%.) 590 - 1,013 hpa
Standard environment
68 °F (20 °C) to 77 °F (25 °C) (65 ± 5 % RH)
Required power supply
AC 208-240V/15A, 60Hz
Power consumption Max. 3.55 kW
Dimensions
42-43/64" (W) × 31-3/32" (D) × 48-11/16" (H)
(1,084 mm (W) × 790 mm (D) × 1,237 mm (H))
(When the operation panel is set to the default position)
Weight
Approx. 651 lbs (295 kg)
Overall dimensions
48-13/16" (W) × 34-9/16" (D)
(1,240 mm (W) × 878 mm (D))
20
Automatic document feeder (Standard equipment)
Name
Duplex Single Pass Feeder (DSPF)
Document feeder types
Duplex Single Pass Feeder (DSPF)
Original paper sizes
11" × 17" (A3) to 5-1/2" × 8-1/2" (A5)
2
Original paper types
Paper storage capacity
250 sheets (21 lbs (80 g/m2))
(or maximum stack height of 1-9/32" (32.5 mm))
Scan speed (copy)
120 one-sided sheets/minute (8-1/2" × 11" (A4) horizontal)
(600 × 300 dpi)
Dimensions
When paper tray is closed
4-39/64" (W) × 19-61/64" (D) × 16-7/64" (H) (117 mm (W) × 507 mm (D) × 409 mm (H))
When paper tray is pulled out
14-11/16" (W) × 19-61/64" (D) × 16-7/64" (H) (373 mm (W) × 507 mm (D) × 409 mm (H))
Weight
16.5 lbs (7.5 kg) or less
2
Paper weightThin paper 10 lbs bond (38 g/m ) to 13 lbs bond (49 g/m )
Plain paper 13 lbs bond (50 g/m2) to 110 lbs index (205 g/m2)
Two-sided
13 lbs index (52 g/m2) to 110 lbs index (205 g/m2)
Multi Bypass Tray
Name
Multi Bypass Tray (MX-MFX1)
Paper sizes
12" × 18" to 5-1/2" × 8-1/2"R (A5R)
Useable paper
16 lbs bond to 110 lbs cover (52 to 300 g/m2)
Paper capacity
100 sheets (21 lbs (80 g/m2))
Large Capacity Trays
MX-LC13
MX-MF11
Name
Large Capacity Trays
Name
Multi Bypass Tray
Paper sizes
12" × 18" (A3W) to 8-1/2" × 11" (B5R) ,SRA3, SRA4
Paper sizes
12" × 18" (A3W) to 5-1/2" × 8-1/2"R (A5R) ,SRA3, SRA4
Useable paper
13 lbs bond to 110 lbs cover (52 to 300 g/m2)
Useable paper
16 lbs bond to 80 lbs cover (52 to 220 g/m2)
5,000 sheets (2,500 × 2 21 lbs (80 g/m ))
Paper capacity
500 sheets (21 lbs (80 g/m2))
Required power supply
AC 120V 60Hz
Required power supply
Supplied from large capacity trays
Dimensions
35-1/4" (W) × 30-1/32" (D) × 38-13/16" (H)
(895 mm (W) × 763 mm (D) × 986 mm (H))
Weight
Approx. 288 lbs (131 kg)
Dimensions
When paper tray is closed
27-3/4" (W) × 21-57/64" (D) × 8" (H) (705 mm (W) × 556 mm (D) × 203 mm (H))
When paper tray is pulled out
34-9/16" (W) × 21-57/64" (D) × 8" (H) (878 mm (W) × 556 mm (D) × 203 mm (H))
Weight
Approx. 39.7 lbs (18 kg)
Paper capacity
2
Large Capacity Tray
MX-LC12
MX-LCX3 N
Name
Large Capacity Tray
Name
Large Capacity Tray
Paper sizes
8-1/2" × 11", A4, B5
Paper sizes
12" × 18" (A3W) to 8-1/2" × 11"R
Useable paper
16 lbs bond to 80 lbs cover (60 to 220 g/m )
Useable paper
16 lbs bond to 80 lbs cover (60 to 220 g/m2)
Paper capacity
3,500 sheets (21 lbs (80 g/m ))
Paper capacity
3,000 sheets (21 lbs (80 g/m2))
2
2
Dimensions
14-13/16" (W) × 22-43/64" (D) × 20-5/8" (H) (376 mm (W) × 576 mm (D) × 524 mm (H))
Dimensions
26-3/8" (W) × 22-7/16" (D) × 20-43/64" (H) (670 mm (W) × 570 mm (D) × 525 mm (H))
Weight
Approx. 63 lbs (28.5 kg)
Weight
Approx. 110 lbs (50 kg)
Required power supply
Supplied from the machine
Required power supply
Supplied from the machine
SPECIFICATIONS
21
SPECIFICATIONS
Finisher
MX-FN24
MX-FN21
Name
Finisher (50-sheet stapling)
Name
Finisher (100-sheet stapling)
Paper sizes
Depends on feeder specifications
Paper sizes
Depends on feeder specifications
Useable paper
13 lbs bond to 110 lbs cover (52 to 300 g/m2)
Useable paper
13 lbs bond to 110 lbs cover (52 to 300 g/m2)
No. of trays
2
No. of trays
3
Tray capacity (21 lbs (80 g/m2)) *
Upper tray
Non-stapled12" × 18" (A3W) / 9" × 12" (A4W) / 11" × 17" (A3) / 8-1/2"
× 14" (B4):50 sheets
8-1/2" × 11" (A4) to 5-1/2" × 8-1/2"R (A5R): 250 sheets
Lower tray
Non-stapled
12" × 18" (A3W) / 9" × 12" (A4W) / 11" × 17" (A3) / 8-1/2"
× 14" (B4) / 8-1/2" × 11"R (A4R) / 5-1/2" × 8-1/2" (B5) /
7-1/4" × 10-1/2"R (B5R): 1,500 sheets
8-1/2" × 11" (A4): 3,000 sheets
5-1/2" × 8-1/2"R (A5R): 100 sheets
Staple function
8-1/2" × 11" (A4): 150 units (2 to 19 sheets)
8-1/2" × 11"R (A4R) / 5-1/2" × 8-1/2" (B5): 100 units (2 to
14 sheets)
11" × 17" (A3) / 8-1/2" × 14" (B4): 100 units (2 to 14
sheets)
Tray capacity (21 lbs (80 g/m2)) *
Upper tray
Non-stapled
12" × 18" (A3W) / 9" × 12" (A4W) / 11" × 17" (A3) /8-1/2"
× 14" (B4) / SRA3 / SRA4: 750 sheets
8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5) /7-1/4" × 101/2"R (B5R) / 5-1/2" × 8-1/2"R (A5R): 1,500 sheets
Staple function
11" × 17" (A3) / 8-1/2" × 14" (B4): 50 units or 750 sheets
8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5): 100 units or
1,500 sheets
Center tray
Non-stapled
12" × 18" (A3W) / 9" × 12" (A4W) / 11" × 17" (A3) / 8-1/2"
× 14" (B4) / SRA3 / SRA4: 125 sheets
8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5) / 7-1/4" × 101/2"R (B5R) / 5-1/2" × 8-1/2"R (A5R): 250 sheets
Lower tray
Non-stapled
12" × 18" (A3W) / 9" × 12" (A4W) / 11" × 17" (A3) / 8-1/2"
× 14" (B4) / SRA3 / SRA4: 750 sheets
8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5) / 7-1/4" × 101/2"R (B5R) / 5-1/2" × 8-1/2"R (A5R): 1,500 sheets
8-1/2" x 11"/A4/B5 Non offset: 2,500 sheets
Staple function
11" × 17" (A3) / 8-1/2" × 14" (B4): 50 units or 750 sheets
8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5): 100 units or
1,500 sheets
Max. no. of stapled sheets
(21 lbs (80 g/m2))
Max. no. of 50 sheets (8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R)/ 5-1/2" × 8-1/2" (B5)
/ 7-1/4" × 10-1/2"R (B5R))
Max. no. of 30 sheets (11" × 17" (A3) /8-1/2" × 14" (B4))
Staple position
Front: 1 position, Back: 1 position, Center: 2 positions, At slant: 1 position
Required power supply
Supplied from the machine
Dimensions
When output paper tray is stored
25-55/64" (W) × 24-13/64" (D) × 38-17/32" (H)
(657 mm (W) × 615 mm (D) × 979 mm (H))
When output paper tray is extended
29-13/32" (W) × 24-13/64" (D) × 40-13/16" (H)
(747 mm (W) × 615 mm (D) × 1,037 mm (H))
Max. no. of stapled sheets
(21 lbs (80 g/m2))
Max. no. of 100 sheets (8-1/2" × 11" (A4), B5)
Max. no. of 50 sheets (11" × 17" (A3), 8-1/2" × 14" (B4), 8-1/2" × 11"R (A4R))
Approx. 103.6 lbs (47 kg)
Staple position
1 bottom, 1 top, 2 middle
Required power supply
AC 120V 60Hz
Dimensions
When output paper tray is stored
25-3/4" (W) × 30-1/8" (D) × 40-15/16" (H)
(654 mm (W) × 765 mm (D) × 1040 mm (H))
When output paper tray is extended
30-51/64" (W) × 30-1/8" (D) × 40-15/16" (H)
(782 mm (W) × 765 mm (D) × 1040 mm (H))
Weight
Approx. 134.5 lbs (61 kg)
Weight
• Offset output is not available for 12" × 18" (A3W) / 7-1/4" × 10-1/2"R (B5R) /
5-1/2" × 8-1/2"R (A5R).
* The amount of paper able to be used may vary depending on the environment the machine is operated in, the type of
paper used, and how the paper is stored.
22
Saddle stitch finisher
MX-FN25
MX-FN22
Name
Saddle Stitch Finisher (50-sheet stapling)
Name
Saddle Stitch Finisher (100-sheet stapling)
Paper sizes
Depends on feeder specifications
Paper sizes
Depends on feeder specifications
Useable paper
13 lbs bond to 110 lbs cover (52 to 300 g/m2)
Useable paper
13 lbs bond to 110 lbs cover (52 to 300 g/m2)
No. of trays
3
No. of trays
4
Tray capacity (21 lbs (80 g/m2)) *
Upper tray
Non-stapled
12" × 18" (A3W) / 11" × 17" (A3) / 8-1/2" × 14" (B4):50 sheets
8-1/2" × 11" (A4) to 5-1/2" × 8-1/2"R (A5R): 250 sheets
Lower tray
Non-sort12" × 18" (A3W) / 11" × 17" (A3) / 8-1/2" × 14" (B4) / 8-1/2" ×
11"R (A4R) / 5-1/2" × 8-1/2" (B5) / 7-1/4" × 10-1/2"R (B5R):
1,000 sheets
8-1/2" × 11" (A4): 2,000 sheets
5-1/2" × 8-1/2"R (A5R): 100 sheets
Staple function
8-1/2" × 11" (A4): 150 units (2 to 12 sheets)
8-1/2" × 11"R (A4R) / 5-1/2" × 8-1/2" (B5): 100 units (2 to
9 sheets)
11" × 17" (A3) / 8-1/2" × 14" (B4): 100 units (2 to 9
sheets)
Saddle stitch tray
10 units (11 to 15 sheets), 15 units (6 to 10 sheets),
30 units (2 to 5 sheets)
Max. no. of stapled sheets
(21 lbs (80 g/m2))
Max. no. of 50 sheets (8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R) / 5-1/2" × 8-1/2" /
7-1/4" × 10-1/2"R (B5R))
Max. no. of 30 sheets (11" × 17" (A3) /8-1/2" × 14" (B4))
Tray capacity (21 lbs (80 g/m2)) *
Upper tray
Non-stapled
12" × 18" (A3W) / 9" × 12" (A4W) / 11" × 17" (A3) /8-1/2" × 14" (B4) /
SRA3 / SRA4: 750 sheets
8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5) /7-1/4" × 10-1/2"R (B5R) /
5-1/2" × 8-1/2"R (A5R): 1,500 sheets
Staple function
11" × 17" (A3) / 8-1/2" × 14" (B4): 50 units or 750 sheets
8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5): 100 units or 1,500 sheets
Center tray
Non-stapled
12" × 18" (A3W) / 9" × 12" (A4W) / 11" × 17" (A3) /8-1/2" × 14" (B4) /
SRA3 / SRA4: 125 sheets
8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5) /7-1/4" × 10-1/2"R (B5R) /
5-1/2" × 8-1/2"R (A5R): 250 sheets
(Offset output is not available)
Lower tray
Non-stapled12" × 18" (A3W) / 9" × 12" (A4W) / 11" × 17" (A3) /8-1/2" × 14" (B4) /
SRA3 / SRA4: 750 sheets
8-1/2" × 11"R (A4R) / 7-1/4" × 10-1/2"R (B5R) / 5-1/2" × 8-1/2"R (A5R):
1,500 sheets
8-1/2" x 11"/ (A4/B5): 2,500 sheets
(Offset output is not available)
Staple function11" × 17" (A3) / 8-1/2" × 14" (B4): 50 units or 750 sheets
8-1/2" × 11" (A4) / 8-1/2" × 11"R (A4R, B5): 100 units or 1,500 sheets
Saddle stitch tray
Non-stapled
16 lbs bond to 28 lbs bond (60 to 105 g/m2): 5 sheets
Staple function
16 lbs bond to 21 lbs bond (60 to 81.4 g/m2): 5 units (16 to 20
sheets), 10 units (11 to 15 sheets), 15 units (6 to 10 sheets), 25 units
(1 to 5 sheets)
21 lbs bond over to 28 lbs bond (81.4 g/m2 over to 105 g/m2): 15 units
(6 to 10 sheets), 25 units (1 to 5 sheets)
Staple function in cover mode
16 lbs bond to 21 lbs bond (60 to 81.4 g/m2): 5 units (16 to 20
sheets), 10 units (1 to 15 sheets)
21 lbs bond over to 28 lbs bond (81.4 g/m2 over to 105 g/m2): 10 units
(1 to 10 sheets)
• Offset output is not available for 12" × 18" (A3W) / 7-1/4" × 10-1/2"R (B5R) /
5-1/2" × 8-1/2"R (A5R).
Max. no. of stapled sheets
(21 lbs (80 g/m2))
Max. no. of 100 sheets (8-1/2" × 11" (A4), B5)
Max. no. of 50 sheets (11" × 17" (A3), 8-1/2" × 14" (B4), 8-1/2" × 11"R (A4R))
Staple position
Front: 1 position, Back: 1 position, Center: 2 positions, At slant: 1 position
Staple method (for saddle stitch)
Centered fold with stapling in 2 center places
Saddle stitch fold position
Centered fold
Saddle usable sizes
11" × 17" (A3) / 8-1/2 × 14" (B4) / 8-1/2" × 11"R (A4R) / 12" × 18" (A3W) / SRA3
Saddle usable paper weight
16 lbs bond (60 g/m2) to 65 lbs cover (176 g/m2)
Paper weighting 28 lbs bond (106 g/m2) to 65 lbs cover (176 g/m2). 65 lbs cover
(176 g/m2) is only able to be used in cover mode and for single sheet fold.
Max. no. of saddle-stitched sheets
Max. no. of 15 sheets (21 lbs (80 g/m2)):
14 sheets (21 lbs bond (80 g/m2)) + 1 sheet (65 lbs cover (176 g/m2))
Required power supply
Supplied from the machine
Dimensions
When output paper tray is stored
25-13/32" (W) × 24-13/64" (D) × 38-17/32" (H)
(657 mm (W) × 615 mm (D) × 979 mm (H))
When output paper tray is extended
29-26/64" (W) × 24-13/64" (D) × 40-13/16" (H)
(747 mm (W) × 615 mm (D) × 1,037 mm (H))
Weight
Approx. 136.7 lbs (62 kg)
* The amount of paper able to be used may vary depending on the environment the machine is operated in, the type of
paper used, and how the paper is stored.
SPECIFICATIONS
Staple position
1 bottom, 1 top, 2 middle
Staple method (for saddle stitch)
Centered fold with stapling in 2 center places
Saddle stitch fold position
Centered fold
Saddle usable sizes
11" × 17" (A3) / 8-1/2 × 14" (B4) / 8-1/2" × 11"R (A4R) / 12" × 18" (A3W) / SRA3
Saddle usable paper weight
16 lbs bond (60 g/m2) to 110 lbs cover (300 g/m2)
Paper weighting 28 lbs bond (106 g/m2) to 110 lbs cover (300 g/m2) is only able
to be used in cover mode and for single sheet fold.
Max. no. of saddle-stitched sheets
Max. no. of 20 sheets (21 lbs (80 g/m2)):
19 sheets (21 lbs bond (80 g/m2)) + 1 sheet (140 lbs index (256 g/m2))
Required power supply
AC 120V 60Hz
Dimensions
When output paper tray is stored
30-13/64" (W) × 30-1/8" (D) × 40-15/16" (H)
(767 mm (W) × 765 mm (D) × 1040 mm (H))
When output paper tray is extended
35-9/32" (W) × 30-1/8" (D) × 40-15/16" (H)
(896 mm (W) × 765 mm (D) × 1040 mm (H))
Weight
Approx. 238.1 lbs (108 kg)
23
SPECIFICATIONS
Curl Correction Unit
Name
Curl Correction Unit (MX-RB18)
Paper sizes
Depends on feeder specifications
Useable paper
Dimensions
8-7/16" (W) × 29-59/64" (D) × 38-13/16" (H)
(214 mm (W) × 760 mm (D) × 986 mm (H))
Depends on feeder specifications
Weight
39.3 lbs (18.5 kg)
Name
Relay Unit (MX-RB13)
Weight
29.5 lbs (13.4 kg)
Dimensions
8-7/16" (W) × 29-59/64" (D) × 38-13/16" (H)
(214 mm (W) × 760 mm (D) × 986 mm (H))
Required power supply
AC 100V-240V 50/60Hz
Dimensions
36-1/64" (W) × 29-27/32" (D) × 38-13/16" (H)
(915 mm (W) × 758 mm (D) × 986 mm (H))
Weight
High Capacity Stacker: 220 lbs (100 kg)
Cart: 33 lbs (15 kg)
Relay Unit
High Capacity Stacker
Name
High Capacity Stacker (MX-ST10)
Paper sizes
12" × 18" (A3W) to 5-1/2" × 8-1/2"R (A5R), SRA3, SRA4
Useable paper
13 lbs bond to 110 lbs cover (52 to 300 g/m2)
No. of trays
2
Upper tray
12" × 18" (A3W) to 5-1/2" × 8-1/2"R (A5R) / SRA3 / SRA4: 250 sheets
Tray capacity (21 lbs (80 g/m ))
2
* Do not load sheets of different sizes.
Lower tray *
12" × 18" (A3W) / 11" × 17" (A3) / 8-1/2" × 14" (B4) / 8-1/2" × 11" (A4) / 8-1/2" ×
11"R (A4R) / SRA3 / SRA4: 5,000 sheets
7-1/4" × 10-1/2" (B5) / 7-1/4" × 10-1/2"R (B5R) / 5-1/2" × 8-1/2"R (A5R): 2,500
sheets
24
Punch module (MX-PNX4B)
Name
Punch module
MX-PNX4B
Paper size for punch module
11" × 17" (A3) to 7-1/4" × 10-1/2"R (B5R)
Holes
2 holes / 3 holes (Manual select)
Required power supply
Supplied from finisher/saddle stitch finisher
Dimensions
5-1/8" (W) × 20-9/32" (D) × 5-33/64" (H)
(130 mm (W) × 515 mm (D) × 140 mm (H))
Weight
Approx. 3 lbs (1.4 kg)
Required power supply
Supplied from finisher/saddle stitch finisher
Dimensions
3-47/64" (W) × 28-5/32" (D) × 9-13/32" (H)
(95 mm (W) × 715 mm (D) × 392 mm (H))
Weight
Approx. 8.6 lbs (3.7 kg)
Punch module (MX-PN13B)
Name
Punch module
MX-PN13B
Paper size for punch module
11" × 17" (A3) to 7-1/4" × 10-1/2"R (B5R)
Holes
2 holes / 3 holes (Auto select)
SPECIFICATIONS
25
SPECIFICATIONS
Network Printer Specifications
Type
Built-in type
Internal fonts (options)
80 fonts for PCL, 139 fonts for Adobe® PostScript®3
Continuous print speed
Same as continuous copy speed
Memory
Machine system memory and hard disk
Resolution
Data processing: 600 × 600 dpi, 1,200 × 1,200 dpi
Print: 600 × 600 dpi, 1,200 × 1,200 dpi
Interface
10BASE-T/100BASE-TX/1000BASE-T, USB 1.1, USB 2.0 (high speed mode)
Page description language
Standard: PCL6 emulation, Adobe® PostScript®3
*:There are cases when a connection cannot be established. Please contact your local dealer for more information.
Compatible protocols
TCP/IP (IPv4/IPv6), IPX/SPX, IPP, EtherTalk
Compatible OS *
Windows Vista, Windows Server 2008, Windows 7,Windows 8, Windows Server 2012
Macintosh (Mac OS × 10.4, 10.5, 10.6, 10.7, 10.8, 10.9 )
Network Scanner Specifications
Type
Color scanner
Scan resolution (main × vertical)
100 × 100 dpi, 150 × 150 dpi, 200 × 200 dpi, 300 × 300 dpi,
400 × 400 dpi, 600 × 600 dpi (push scan)
50 to 9,600 dpi *1 (pull scan)
Scan speed
(8-1/2" × 11" (A4))
B/W:
120 sheets/minute (one-sided)
Color:
120 sheets/minute (one-sided)
hen in standard mode using TOSHIBA standard paper (8-1/2" × 11" (A4)
W
size with 6% coverage) and the auto color detector is turned off. The speed
varies depending on the data volume of the original.
Interface
10BASE-T/100BASE-TX/1000BASE-T,
USB 2.0 (during USB memory scanning)
Compatible protocols
Compatible OS *
2
TCP/IP (IPV4)
Output format
(B/W)
TIFF, PDF, PDF/A, encrypted PDF, XPS *4
Compression method: decompression, G3 (MH), G4 (MMR)
(Gray scale/color)
TIFF, JPEG, PDF, PDF/A, encrypted PDF, high compression PDF *3, XPS *4
Compression method: high, mid, and low compression, Emphasis black letter *5
Driver
TWAIN compliant
*1:You must decrease the scan size when increasing the resolution.
*2:There are cases when a connection cannot be established. Please contact your local dealer for more information.
*3:A scanner function expansion kit (MX-EB11) is required.
*4:XPS (XML Paper Specification)
*5:When PDF, PDF/A, or Encrypt PDF is selected
Pull scan (TWAIN)Windows Vista, Windows Server 2008, Windows 7,
Windows 8, Windows Server 2012
26
Trimming Module
Name
Trimming module (MX-TM10)
Required power supply
Supplied from saddle stitch finisher
Useable size for trimming module
12" × 18" (A3W), 11" × 17", 8-1/2" × 14", 8-1/2" × 13-1/2", 8-1/2" × 13-2/5",
8-1/2" × 13", 8-1/2" × 11"R, SRA3, A3, B4, A4R
Dimensions
9-7/8" (W) × 24-15/32" (D) × 15-7/8" (H)
(251 mm (W) × 625 mm (D) × 403 mm (H))
Weight
Approx. 70.6 lbs (32 kg)
Max. no. of sheets to be trimmed
2 to 20 sheets (16 lbs bond to 21 lbs bond (60 g/m2 to 81.4 g/m2))
2 to 10 sheets (21 lbs bond over to 28 lbs bond (81.4 g/m2 over to 105 g/m2))
2 to 3 sheets (28 lbs bond over to 80 lbs cover (105 g/m2 over to 220 g/m2))
• When plain paper trimmed. Including one front cover of 110 lbs cover (300
g/m2) or less.
Folding Unit
Name
Folding unit (MX-FD10)
Folding types
Z-Fold, C-Fold, Accordion Fold, Double Fold, Half Fold.
Useable size for folding unit
Z-Fold: 11" × 17", 8-1/2" × 14", 8-1/2" × 11"R, A3, B4, A4R
C-Fold, Accordion Fold, Double Fold, Half Fold: 8-1/2" × 11"R, A4R
Useable paper
13 lbs bond to 28 lbs bond (52 g/m2 to 105 g/m2))
Tray capacity (21 lbs (80 g/m ))
C-Fold/Accordion Fold/Double Fold
2-23/64" (60 mm) (Equivalent to 40 sheets. (Equivalent to 25 sheets for Double Fold))
• Copies made in Z-Fold or Half Fold are output to the tray of the finisher (large
stacker) or saddle stitch finisher (large stacker).
Required power supply
Supplied from finisher/saddle stitch finisher
Dimensions
13-15/32" (W) × 30-5/16" (D) × 41-11/32" (H)
(336 mm (W) × 770 mm (D) × 1050 mm (H))
Weight
Approx. 145.5 lbs (66 kg)
Tray capacity (21 lbs (80 g/m2))
Upper tray: 200 sheets
Lower tray: 200 sheets
Required power supply
Supplied from the machine
Dimensions
21-1/4" (W) × 29-7/8" (D) × 50-1/4" (H)
(540 mm (W) × 760 mm (D) × 1276 mm (H))
Weight
Approx. 99.2 lbs (45 kg)
2
Inserter
Name
Inserter (MX-CF11)
Useable size for inserter
12" × 18" (A3W), 9" × 12" (A4W), 11" × 17", 8-1/2" × 14", 8-1/2" × 13-1/2",
8-1/2" × 13-2/5", 8-1/2" × 13", 8-1/2" × 11", 8-1/2" × 11"R, 7-1/4 × 10-1/2"R,
5-1/2" × 8-1/2"R, A3, B4, A4, A4R, B5, B5R, A5R, SRA3, SRA4
Useable paper
16 lbs bond to 80 lbs cover (60 g/m2 to 220 g/m2))
No. of trays
2
SPECIFICATIONS
27
SUPPLIES
Standard supplies for this product that can be replaced by the user include paper,
toner cartridges, and staple cartridges for the finisher.
Be sure to use only TOSHIBA-specified products for the toner cartridges, finisher
staple cartridge, and transparency film.
GENUINE SUPPLIES
For best copying results, be sure to use only TOSHIBA Genuine Supplies which are
designed, engineered, and tested to maximize the life and performance of TOSHIBA
products. Look for the Genuine Supplies label on the toner package.
Storage of supplies
„„ Proper storage
„„ Storing toner cartridges
1.Store the supplies in a location that is:
Store a new toner cartridge box horizontally with the top side up. Do not store a toner
cartridge standing on end. If stored standing on end, the toner may not distribute
well even after shaking the cartridge vigorously, and will remain inside the cartridge
without flowing out.
• clean and dry,
• at a stable temperature,
• not exposed to direct sunlight.
2.Store paper in the wrapper and lying flat.
3.Paper stored in packages standing up or out of the wrapper may curl or become
damp, resulting in paper misfeeds.
„„ Staple cartridge
The finisher and saddle finisher require the following staple cartridge:
MX-SCX3 (for saddle stitch of saddle stitch finisher)
Approx. 2000 per cartridge 4 cartridges
MX-SCX2 (for finisher (large stacker) and saddle stitch finisher (large stacker))
Approx. 5000 per cartridge 3 cartridges
MX-SCX1 (for saddle stitch of saddle stitch finisher (large stacker))
Approx. 5000 per cartridge x 3 cartridges
AR-SC2 (for finisher and saddle stitch finisher)
Approx. 5000 per cartridge x 3 cartridges
Supply of spare parts and consumables
The supply of spare parts for repair of the machine is guaranteed for at least 7 years following the termination of production. Spare parts are those parts of the machine which
may break down within the scope of the ordinary use of the product, whereas those parts which normally exceed the life of the product are not to be considered as spare parts.
Consumables too, are available for 7 years following the termination of production.
28
OPTIONS
Optional Units
When optional units are installed, finishing operations such as stapling, punching or folding, can be performed.
9
1
2
3
4
5
6
7
1 Finisher/Saddle Stitch Finisher
6 This Unit
2 Folding Unit
7 Multi Bypass Tray
3 High Capacity Stacker
8 Large Capacity Trays
4 Inserter
9 Status Indicator
8
5 Curl Correction Unit
29
OPTIONS
Finisher/Saddle Stitch Finisher
Folding Unit
Each set of copies can be stapled, or the sheets can be folded and stapled.
Installing a punch module automatically enables hole punching that is convenient
for filing.
Each set of copies can be folded.
Finisher
MX-FN24
Finisher
MX-FN21
• e-STUDIO907 only
• 50 sheets
• 100 sheets
Saddle Stitch Finisher
MX-FN25
Saddle Stitch Finisher
MX-FN22
• e-STUDIO907 only
• 50 sheets
• 15 sheet (saddle stitch finisher)
• 100 sheets
• 20 sheets (saddle stitch
finisher)
• For saddle folding, it trims a
side drop, offering a goodlooking output image (In use of
trimming module).
Folding Unit
MX-FD10
•
•
•
•
•
Half Fold
Z-Fold
C-Fold
Accordion Fold
Double Fold
High Capacity Stacker
Inserter
Stacks a large number of sheets in the stacker tray of the paper cart, enabling you
to move the stacker tray on the stacker cart. This stacker provides an LED that
notifies users of the status. You can connect up to two large capacity stackers.
Inserts a sheet of paper into a specific page as an insertion sheet.
High Capacity Stacker
MX-ST10
Inserter
MX-CF11
• 200 sheets x 2
PAPER CART
MX-CA10
30
Large Capacity Trays
Curl Correction Unit
You can drastically reduce the time to load the large number of paper.
Perform the curl correction of the output.
Large Capacity Tray
MX-LC12
Large Capacity Tray
MX-LCX3 N
• 8-1/2" x 11", A4 or B5 paper
can be loaded.
• e-STUDIO907 only
• 12" x 18" (A3W) to 8-1/2" x 11"
(B5) paper can be loaded.
Curl Correction Unit
MX-RB18
Large Capacity Trays
MX-LC13
• Up to two large capacity trays
can be connected.
• 2 trays
Status Indicator
These indicators show the status of the machine.
Status Indicator
MX-SL10 N
OPTIONS
31
ADMINISTRATOR
Forwarding all sent or received data to the administrator (document administration function)
This function is used to forward all data sent and received by the machine to a specified destination (Scan to E-mail address, Scan to FTP destination or Scan to Network Folder destination). This function can be used by the administrator of the machine to archive all sent and received data. To configure the document administration settings, click [Application Settings] and
then [Document Administration Function] in "Settings mode". (Administrator rights are required.)
The forwarding data, exposure, and resolution settings of sent and received data
remain in effect.
Setting mode password
An administrator password is required to configure the machine settings using administrator
rights.
The settings can be configured from either the operation panel or by using a computer web
browser.
After setting up the machine, refer to "Settings mode" in the User’s Manual to set a new
password.
The same administrator password is used for the operation panel and the Web page.
If the administrator changes a password on the operation panel, the password will be
valid when logging in to the Web page.
The factory default passwords for respective accounts are shown in the following.
Logging in as an "Administrator" or "System Administrator" allows you to manage all the
settings available via Web browser.
User
Account
Password
users
users
Administrator
admin
admin
System administrator
sysadmin
sysadmin
Do not forget the new administrator password.
Password for logging in from a computer
As factory default, "Administrator" is the only account allowed to log in from a Web browser. By
setting user authentication, "System Administrator" will also be allowed to log in from the Web
browser. You can also specify a device account as a login user.
32
OTHERS (NOISE EMISSION)
Noise emission
Sound pressure level LpAm
Noise emission values
Operating
The following shows noise emission values as measured according to ISO7779.
Standby
Sound power level LWAd
Operating
Standby
e-STUDIO907
e-STUDIO1057
e-STUDIO1207
7.9 B
8.0 B
8.1 B
-
-
-
e-STUDIO907
e-STUDIO1057
e-STUDIO1207
61 dB
62 dB
62 dB
-
-
-
• Operating: With options MX-FN21, MX-RB18, and MX-MFX1.
• Standby: “ -” = less than background noise.
Security Precautions
In order to make correct use of this product’s security function, first read the following precautions
carefully. Be sure to assign administrators who have enough capability to sustain responsible management since significant privileges for managing and handling this equipment will be given them.
To Administrators
• To avoid physical security problems, such as hardware removal or inappropriate
disassembly at the installation site, take all necessary measures, such as checking
who enters and leaves the site.
• When connecting this product with an outer network such as the Internet, only
operate it in a network environment protected by a firewall, etc. to prevent
information from being leaked due to incorrect settings or avoid illegal access by
unauthorized users.
• To prevent the configuration settings from being altered improperly or similar, before
you use this product, change the administrator and user registration passwords set
by factory default. Also, be sure periodically to change each password set for this
product.
• In order to make proper use of the network and user management functions, be
sure to read the User's Manual first.
• Be sure to understand the security policy and its procedure in your organization, and
manage and operate this equipment and external devices according to the policy after
first reading the operator's manual. Then explain the security instructions to general
users who are authorized to use this equipment to let them conform to the security rule.
• Provide general users with the appropriate privilege of using this equipment and
keep supervising its correct operation.
• Always check if the network function and user management function are enabled
in order to maintain security. Should you happen to come across any abnormality,
contact your service technician immediately. See the User's Manual for the checking
method.
• If any failure or unauthorized access occurs in this equipment, check the logs in Job
Logs to find the cause. For details of checking logs, refer to the User's Manual.
• Check your log regularly to guard against unauthorized access by identity theft.
To general users
• After you have finished operating the equipment, be careful not to forget to remove
any originals, printed paper or USB storage devices.
• Change the password regularly. Make sure not to use any predictable number such
as your birthday or employee ID number, and keep it secret.
• Do not leave the equipment during the performance of the job since your originals
may be seen or the output paper could be taken by someone.
33
PRINTED IN CHINA
2014L YT1
TINSE5315FCZZ
DIGITAL MULTIFUNCTIONAL SYSTEM
Quick Start Guide
1-11-1, OSAKI, SHINAGAWA-KU, TOKYO, 141-8562, JAPAN
2014 TOSHIBA TEC CORPORATION All rights reserved
DP-9077/1057/1207
OME14009800
R140820P1700-TTEC
Ver00 F 2014-09
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement