Allen-Bradley 140G-K-PB3H Installationsanleitung
Allen-Bradley 140G-K-PB3H is a phase barrier used to separate different phases in an electrical system. It is designed to prevent the flow of current between the phases, and to protect the equipment from damage. The 140G-K-PB3H is made of a high-quality plastic material that is resistant to heat and chemicals. It is also UV-resistant, which makes it suitable for outdoor use. The 140G-K-PB3H is easy to install and can be used in a variety of applications, including:
- Electrical distribution systems: The 140G-K-PB3H can be used to separate different phases in an electrical distribution system. This helps to prevent the flow of current between the phases, and to protect the equipment from damage.
Advertisement
Advertisement
Bul. 140G/140MG
DIR 1000436R0644 Version 01 - 140G-K-PB3L, 140G-K-PB4L, 140G-K-PB3H, 140G-K-PB4H, 140G-R-PB3L, 140G-R-PB4L, 140G-R-PB3H, 140G-R-PB4H
Phase barriers 140G-K,-N,-NS,-R
Separatori di fase
Trennwande zwischen den Phasen
Sèparateurs de phase
Separadores de fase
相间隔板
Installation - Installazione - Instalación
Instalação - -
WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
(Seguire i requisiti NFPA70E).
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen
Sie die Anforderungen nach NFPA70E).
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs. (Vous devez respecter la norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de contaminantes. (Cumpra as exigências da norma NFPA70E).
警告:感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
確認してください。(
NFPA70E
の要件に従ってください)
警告:为了防止触电,在安装或维修之前必须先切断电源。安装在合适的设备
物
140G-K-PB_H
140G-K-PB_L
1
140G-K
2
3p
4p
140G-K 140G-N 140G-NS 140G-R x4 x6 x4 x6 x4 x6 x2 x3
140G-N,-NS
DIR 1000436R0644 Version 01
3
140G-R
4
140G-R
5
140G-R
10.6 lb-in
1.2 Nm
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/ sustainability-ethics/product-environmental-compliance.page
Publication 140G-IN015B-MU-P - April 2016 DIR 1000436R0644 Version 01 (L5651) - B0822
Copyright © 2016 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.
Advertisement