F11 Installation Guide

F11 Installation Guide
F11 Installation Guide
Version: 1.0
Date: Jul. 2010
Table of Contents
Table of Contents
1. Before Installing .................................................................................................... 1
1.1 Notice About Installing .............................................................................. 1
1.2 Operation Panel:......................................................................................... 3
2. System Configuration............................................................................................ 5
3. Installation............................................................................................................. 5
3.1 Device Installation...................................................................................... 5
3.2 Connect with External Equipment.............................................................. 6
3.2.1 Connect to the Access Controller ................................................... 7
3.2.2 Connect to Alarm ........................................................................... 7
3.2.3 Door Lock Connection ................................................................... 7
3.2.4 Communication Mode.................................................................... 7
3.2.5 Complementary Communications .................................................. 7
3.2.7 Power Connections......................................................................... 7
3.3 Fixed the Device......................................................................................... 7
4. Other Functions ..................................................................................................... 7
4.1 Reset Button ............................................................................................... 7
4.2 Tamper Switch............................................................................................ 7
4.3 Built-in EM Card Reader (Optional) .......................................................... 7
4.4 Built-in MIFARE Card Reader (Optional) ................................................. 7
5. Trouble Shooting ................................................................................................... 7
1. Before Installing
1. Before Installing
1.1 Notice About Installing
This device is a mass-produced product. It strictly tested comply
with the standard of China, U.S.A, and EU. This file contains important
information. It is better for you to read it carefully prior to use. If you
ignore it, the incorrect installation may cause the unit damage.
Although we could do our best to offer you service, the neglect to the
guide could cause unwanted cost for you.
1. Before installation, please make sure the power is cut off,
because it is very dangerous if the power is on. The short circuit of
power cable may cause the core parts damage.
2. All exposed part of connection wire end cannot be exceeded
5mm to prevent the bared wire accidental connection which leads to
device break down. And also suggest using different color cable to
connect.
3. In the place where the static is strong or in winter, please
connect the grounding firstly, in order to prevent the instant mass static
damage the device.
4. Connect power supply with device in the last for the wiring
connection. If you find any unusual thing occur, please firstly cut off the
power, then go to examine. Keep in mind: wiring operation under power
on will lead to device sudden damage; we are not liable for damages
and troubles due to such operation.
1
F11 Installation Guide V1.0
5. The height to mount device is about 1.4-1.5 meter.
6. After installation, please take off protection film on the fingerprint
sensor to get best recognize result.
7. After installation finish, when go to test the exit button, please
keep a personal in the outside, because sometimes the accidental issue
can bring on you that you are not able to go outside.
8. It is good to use more than 12V/1.5A independent DC power
supply for this device. It can reduce the electric interference between
the device with controller or electric lock, current ripple wave is less
than 150mV.
9. In connecting of the Fingerprint reader, 8-shielding cable (RVVP
8X0.3MM2) is recommended to reduce the interference in the course of
transmission, please read and always follow "F11 Installation Guide"
closely. Because the wrong wiring will cause the core block and sensor
to burn out, lead to device breaking down, at this cause we are not liable
for any damages and troubles.
10. +12VDC power supply cable by two-core power cord (RVV
2X2.5MM2), If the distance between power adapters and device is too
long, please do not use the other type wire for replacement. When you
select the power wire, you should pay attenuation to the voltage decay
of long distance transfer.
11. Please use specialized RS485 cable,the internationally popular
RVVP (shielded twisted pair) is recommended, Model RVVP
2x0.5-1.5mm2 (two core shielded twisted pair) and the active
RS232/RS485 converter to connect with the network, the bus structure
apply to connect with each device. When a long cable is used to transfer
2
1. Before Installing
signal, it is need to connect a matching resistance to each terminal, and
its value is 120Ώ.
12. Signal cable (such as RS485 cable) and high-power electricity
cable (such as AC electric, locking cable) can not place in parallel. If it
is necessary, please put them about 50cm away.
More details please see to the F11 User Manual, the appendix, the
other instructions and so on.
1.2 Operation Panel
Power Button
LED Indicator
Fingerprint Sensor
Sensor Area
1. Power Button: Press and hold the power button for three
seconds to turn the power off, press and hold the power button one
second to turn it on.
2. Fingerprint Sensor:Used to enroll or match fingerprint and
delete user.
3
F11 Installation Guide V1.0
3. LED Indicator: The LED indicator is used to display device
operation, enrollment, deletion or verification state.
4. Card Sensor Area: Used to sense the administrator card for
management, or the ordinary card for enrollment, matching and deletion.
4
2. Installation
2. Installation
2.1 Standard Connection
There are three modes that the PC software communicate and
exchange information with the device: RS232, RS485, TCP/IP. RS485 and
TCP/IP modes support remote control.
The standard connection diagram shown below:
2.2 Device Installation
This product is designed for indoor installation, if it has to be
installed outdoor, please place the equipment in proper surroundings, you
must beware of not exposing it to water or harsh condition , we
recommend to embed the cable into the wall, if it isn’t capable to do, you
must obtain the user’s permission before installing.
5
F11 Installation Guide V1.0
2.3 Connect with External Equipment
To avoid the possible damage to the device, before connecting or
disconnecting external equipment, you should make sure to disconnect the
power cable first. Please follow the installation guide to connect the
external equipment.
1. Access Controller.
2. Alarm.
3. Various network..
4. Auxiliary communication interface.
6
2. Installation
5. Power supply.
Wiring terminal for external equipment shown as below:
2.3.1 Connect with Access Controller
As a fingerprint reader, F11 can not work alone until it connect with
the access controller. It is only a fingerprint identification device in the
system, and provide the controller with a standard or self-define Wiegand
signal. Such as others card reader we adopt the standard signal (D0, D1,
GND) connection mode (See Standard Connection Diagram).
"Notice: Whether the power of F11 supply by the access controller or
7
F11 Installation Guide V1.0
not, the two equipment’s GND must be in common connection. Do not
replace Weigand signal GND with power GND. To ensure the wiegand
signal transfer steady, please separately plot wiring.
THD
TIW
TSD
SS
WD0
TDW
SS
WD1
Specifications:
TDW pulse: 400 um
TIW cycle: 2000 ms
Output drive capability: 200 mA
Definition terminal connection (7 PIN Cable) :
Terminals
Function
1
ALM
Alarm Signal
2
/
3
/
4
/
5
WD1
Wiegand Output
6
WD0
Wiegand Input
7
GND
Power Output
8
2. Installation
2.3.2 Connect to Alarm
F11 can connect a alarm signal (Alarm) to system, which mainly use
to remind that the F11 has been dismantled. No matter what condition,
when it is removed, F11 will trigger alarm output in the power on state,
otherwise, the wire doesn’t send any signal. F11 will link GND through
the wire if the system be triggered, follow this principle we can achieve
the remind function of dismantled alarm. Connect the negative of alarm
power to alarm output, the positive of alarm power connect to the positive
of F11 power (See the figure below), F11 alarm output only support
12VDC alarm.
"Notice: There is a tamper switch in the bottom of F11. For details, see
3.2 Tamper Switch.
Alarm connection diagram shown as below:
9
F11 Installation Guide V1.0
"Notice: The power output of the alarm is no more than DC12V.
2.3.3 Door Lock Connection
The way of installing door lock depends on the type of lock and local
condition. Internal resistor which comes from long distance transfer
should be taken into consideration when selecting the cable of electric
power. The door lock should be installed reliable and stable. Ensure the
wiring is correct. For the strike lock and electromagnetic lock, you should
pay attention to positive and negative terminal connection. The unused
10
2. Installation
bare end of wire should be cut off and use insulating tape to wrap it. The
delay time of strike lock is adjustable according to different conditions.
Select electric lock:It is better to use electric drop bolt for the two
direction opening glass door (Both open to inside or outside direction). For
the single opening wood door in company internal, we recommend to use
magnetic lock, the magnetic lock also be called as electric magnetic lock.
The magnetic lock is more reliable than the electric drop bolt, but the
electric drop bolt is much safer than the magnetic lock. In the small living
community, it is better to use electric drop bolt and magnetic force lock.
The electric control lock gives out higher noise. The electric control lock
is commonly used to building communication. Now there is a soundless
electric control lock which is able to be applied. Please pay attention, the
lock is made of iron and easy rust, so you must beware of not exposing it
to water or harsh condition, there are some other electric locks available,
we don’t recommend you to use them.
Connect with electric lock:The Normal Open lock is open when the
power is off. The Normal-Close lock is closed when power is off. The
device supports both of the two kinds of locks at the same time. The way
of lock connection changes with the type of lock. For NO lock, the NO
terminal will be used; for NC lock, the NC terminal will be used.
When the DC power electrical lock is connected to the system, you
need to parallel one FR 107 diode (Equipped in the package) to prevent
the self-inductance EMF affect the system, do not reverse the polarities
This access control device is powered by DC12V and the work
current is 400mA. If the lock work electric power is DC12V and the work
current is less than 1000mA, the fingerprint device and lock are able to be
powered by one adapter together, please refer to the table 1), 2).
11
F11 Installation Guide V1.0
In the following three cases, we recommend that fingerprint device
and lock are powered separately.
1. The working voltage of the lock is DC12V, but the current
difference of the fingerprint device and the lock doesn’t exceed 1A.
2. The lock voltage is not DC12V.
3. The distance between lock and fingerprint device is too far.
Lock Connection Diagram
1) NC lock connection
(The device and lock
power by one adapter).
2) NO lock connection
(The device and lock
power by one adapter).
12
2. Installation
3) NC lock connection
(The device and lock
powered by independent
adapters).
4) NO lock connection
(The device and lock
powered by independent
adapters).
2.3.4 Communication Mode
The communication line should be as far as possible away from the
high voltage wire. It should not be parallel with the power cable, do not
13
F11 Installation Guide V1.0
bundle them together.
Terminals
Function
RXD
RS232 Data Receiver
TXD
RS232 Data Transmit
GND
Ground
485-
RS485-
485+
RS485+
RJ45-6
RJ45-3
RJ45-2
Ethernet
RJ45-1
RS485 Communication Mode:
1. While using RS485 communication mode, specified RS485 cable
and active RS232/485 converter required, bus structure is recommended.
14
2. Installation
2. If RS485 communication distance is over 300 meters, add a
terminal matched resistor (with 120Ω) to RS485 bus. See the diagram
below, add the resistor to 0# and 7# devices.
2.3.5 Complementary Communications
The complementary communications such as Ethernet and RS232
Mode, shown below.
15
F11 Installation Guide V1.0
1. Ethernet Mode:
Connect the device with PC through crossover cable.
2. Ethernet Mode:
Using the straight cable to connect the device and the PC to the
Switch/Hub.
3. RS232 Mode:
16
2. Installation
2.3.6 Power Connections
F11 power supply is 12VDC, standby current about 50mA, operating
current of about 300mA, please use only approved the power adapter, the
power adapter must be rated for the product and for the voltage and
current marked on the product’s electrical rating, otherwise it will cause
serious damage. (See standard connecting figure). Power requirements:
DC 12V (- / + 2V) - 1A.
"Note: F11 directly power on through the power supply of the access
controller, can also be an external sources of power.
The define of terminal connection:
Terminals
Function
GND
Cathode
+12V
Positive
DC +12V
2.4 Fixed the Device
After be sure all cable are inserted correctly into, fix installed
17
F11 Installation Guide V1.0
backplane, and mount F11 on the backplane.
"Note: Please strictly in accordance with the definition to connect, and
connect completed, All exposed part of connection wire end cannot be
exceeded 5mm to prevent the bared wire accidental connection which
leads to device break down. in particular the red cable, as a 12 V output
voltage, when there is no an external card reader, in any case ensure to cut
this cable and use the insulation adhesive plaster to dress it, so as to avoid
short-circuit.
18
3. Other Functions
3. Other Functions
3.1 Reset Button
Due to operation error or other accidence, which leads the device
not to work, you can restart device through reset key.
1. Take a small tool which diameter is no more than 2mm.
2. Find the “Reset” mark on the left of the small hole at the bottom
of device, see following figure.
3. Use the tool stick into the hole refer to the picture below, then
the device restart.
Reset Button
3.2 Tamper Switch
The tamper switch is pressed and held down with the rear cover.
When the device is dismantled, the tamper switch will be lifted up and
then it will send an signal to trigger an alarm.
Clear alarm: The user can clear the alarm by unlocking the door
upon successful verification.
19
F11 Installation Guide V1.0
Restore factory defaults: The factory defaults can be restored
through the tamper switch.
When the system generates an alarm for 30–60 seconds, the user
can press the tamper switch three times (Till the speaker sounds) to
restore default settings, including the device number, system password,
IP address, 485 address, and keyboard password.
#
Tip: The user information stored on device will be cleared
after the device is restored to factory defaults, please be cautious.
Tamper Switch
3.3 Embed EM Card Reader (Optional)
Embed a non-contact EM card reader module, the distance of
flashing card is 5-10cm. it completely supports the thick card (1.88mm),
middle card (1.05mm), and thin card (0.88mm), whose operating
frequency is at 125KHz, the card sensor area as following illustration.
20
3. Other Functions
3.4 Embed MIFARE Card Reader (Optional)
Contain a non-contact MIFARE card reader module , the distance
to detect card is 5-10cm, it completely supports MIFARE cards that
provide operating frequency 13.56MHZ, communication speed
106KBPS, the card sensor area is as following illustration.
Card Sensor Area
21
4. Trouble Shooting
4. Trouble Shooting
Trouble
Cause & Measure
Power LED is off
Cause: No power or lack of voltage.
Measure:
①Check and examine the connection of PWR,
GND, make sure they contact well.
②Measure the supply voltage, ensure that it is
12VDC.
Device is unable
to connect with
PC
Cause:
①The connection problem.
②Communication parameters not configure right,
such as IP address RS232/ RS485 baud rate,
system password, etc.
Measure:
①Check and examine the connection of
RS232/RS485 or TCP/IP, whether its connection is
correct or not.
②Change the communication mode to connect
with PC, and check the parameters.
After the power
is on, the device
cycle reboot.
Cause:
①For long time used, surface of fingerprint sensor
becomes dirty, or there are some scratches on it,
the device takes it as a fingerprint and does
verification.
②Fingerprint connection cable of fingerprint
sensor is loosed.
③ Chip-on-board is broken.
22
4. Trouble Shooting
④Lack of power.
Measure:
①Under such situation you can use scotch
tape to adhere the dirt.
②, ③Need to contact suppler and apply for repair.
④Use a multimeter to measure the power voltage.
The fingerprint
sensor light is off
Cause:
①Fingerprint connection cable is broken.
②Fingerprint sensor broke down.
Measure:
①Please take out the FFC from slot of fingerprint
sensor, plug it again.
②Contact suppler, apply for repair.
Wiegand output
problems:
After
correctly
match fingerprint
or swipe card, the
controller can not
accept the card
number
or
numbers error.
Cause:
①communication distance between fingerprint
reader and access controller is too long
②Poor communications environment
③Access Controllers request fingerprint reader
have a stronger signal drive capability
④Output circuit damage, put a multimeter to DC
profile and measure WD0, WD1 pins, when
verification successful, two pins voltage is subject
to fluctuations, without fluctuations or 0 V, the
circuit has proved damage.
Measure:
①Communications distance between fingerprint
reader and access controller is no more than 100
meters, longer distance need to connect
conversion circuit
②Improve communications environment, use a
better shielding cable to reduce external
interference.
③Modify the WIEGAND output signal of the
fingerprint reader, adjust the low-pulse cycle to
500us, adjusted the cycle to 2ms. Then add the
resistance to offset the access controller’s input
pull-up resistor.
④Contact with the vendor for warranty.
Failed
RS485
communication
Cause:
①RS485 communications line connection wrong.
②Communications baud rate is too high (In the
proposed multiple device networking as 9600)
③Too long distance of communication or poor
environment
④ Among network, a RS485 chip of the
fingerprint reader damaged, that caused the
network paralysis.
⑤Two machines have the same IP address.
⑥Too many devices over the network will affect
the communication distance and the RS485 signal
stability.
⑦ RS232/485 converters drive capability no
enough.
Measure:
①The theory longest distance between fingerprint
reader and access controller is 1,200 meters
24
4. Trouble Shooting
(Actual apply is not recommended more than 500
meters), longer distance than add repeaters.
②Communication baud rate adjust to 9600.
③Add the terminal matched resistance to RS485
bus in the starting terminal and the end terminal,
resistance is about 120 Ω.
④ Improve
communications
surrounding
environment, use a good shielding cable and
smaller distributed capacitance wires to reduce
external interference.
⑤Cut off the power of fingerprint reader one by
one to position the failure terminal.
⑥ Reducing the number of machines, or
increasing RS232/485 converter or RS485
network/
⑦Recommend to use active RS232/485 converter.
Information in this document is subject to change without notice.
Printed in China
26
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement