Sony MZ-R55 portable minidisc recorder Operating instructions

S O N Y 3-864-987-21 (1)
Portable
MiniDisc Recorder
Operating instructions
UN
|
Un
A
E
5 |
D
x
=
2)
=)
MZ-R55
©1998 by Sony Corporation
To prevent fire or shock
hazard, do not expose the
unit to rain or moisture.
To avoid electrical shock,
do not open the cabinet.
Refer servicing to
qualified personnel only.
Caution
The use of optical instruments with this
product will increase eye hazard.
Information
For Customers in the USA
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are
designed to provide reasonable protection
against harmful interference in a
residential installation. This equipment
generates, uses. and can radiate radio
frequency energy and, if not installed and
used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
following measures:
— Reorient or relocate the receiving
antenna.
— Increase the separation between the
equipment and receiver.
— Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
— Consult the dealer or an experienced
radio/ TV technician for help.
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
The built-in battery should be replaced by
qualified personnel only.
For Customers in Australia
If the supply cord of the AC power
adaptor is damaged, the AC power
adaptor must be returned to the
manufacturer or his agent for the cord to
be replaced.
For the customers in the USA
DISPOSAL OF NICKEL METAL
HYDRIDE BATTERY
NICKEL METAL HYDRIDE BATTERY.
DISPOSE OF PROPERLY.
You can return your unwanted nickel
metal hydride batteries to your nearest
Sony Service Center.
Note: In some areas the disposal of nickel
metal hydride batteries in household or
business trash may be prohibited.
For the Sony Service Center nearest you
call 1-800-222-SONY (United States only)
Caution: Do not handle damaged or
leaking nickel metal hydride battery.
IN NO EVENT SHALL SELLER BE
LIABLE FOR ANY DIRECT,
INCIDENTAL OR CONSEQUENTIAL
DAMAGES OF ANY NATURE, OR
LOSSES OR EXPENSES RESULTING
FROM ANY DEFECTIVE PRODUCT
OR THE USE OF ANY PRODUCT.
Owner's Record
The serial number is located at the rear of
the disc compartment lid and the model
number is located at the top and bottom.
Record the serial number in the space
provided below. Refer to them whenever
you call upon your Sony dealer regarding
this product.
Model No. MZ-R55
Serial No.
"MD WALKMAN" is a trademark of Sony
Corporation.
|] . Title function —_ You can see disc and
Welcome! track titles in the display while you are
playing/recording an MD.
Welcome to the world of the MiniDisc!
Here are some of the capabilities and
features you'll discover with the new
MiniDisc Recorder. N
* Recording MD Walkman in an ultra-
compact body — Almost as small as a
playback-only MD Walkman; easy to
carry in your pocket or bag.
* Low power consumption design —
Runs on a single "chewing gum” type
rechargeable battery.
* Simultaneous labeling feature — No
more waiting for the recording to end;
you can label tracks and discs while the
MD is being recorded.
* O-letter, backlit LCD remote control
with editing capabilities — You can
now label tracks and discs, change
track sequence, etc., with the easy-to-
operate stick remote control.
» Shock-resistant memory — Offsets up
to 40 seconds of optical read errors.
* High-fidelity recording — Low-noise,
low-distortion, high-fidelity recording
through the optical digital input jack.
* Digital synchro-recording — When
recording from a digital equipment
with optical output, the recorder
automatically starts and pauses
recording in sync with operation on the
digital source.
* Sampling rate converter — This unit
enables you to record programs from
digital equipment using other
sampling rates, such as a BS tuner or
DAT deck.
* Digital AGC (Auto Gain Control) —
Automatic recording level adjustment
without sacrificing superb digital
sound. |
* Long-time recording with monaural
sound — You can record up to 148
minutes on a disc using monaural
recording.
* Date and time stamp function — The
built-in clock automatically records the
date and time whenever you make a
recording.
Table of contents
Recording an MD right away! .................ee..—. «===... 6
Playing án MD right away! .............e====...=.e.eeenaneo 8
Various ways of recording ...............-.........e..e=...... 10
Two ways of connecting to a sound SOUFCE ...................e..100e ie... 10
Recording with digital input (optical cable required) ...................... 11
To start/stop recording in sync with the source player
(Synchro-recording) .....................e..eieee ee eee 11
Recording from a microphone ..................0veeeereee see. 12
Recording in monaural for double the normal recording time ...... 13
Adjusting the recording level manually (Manual recording) ......... 13
Checking the remaining time or the recording position .................. 14
Оп the recordeT esse ee, 14
On the remote contrOl esse EEE 15
Setting the clock to stamp the recorded time ……….…...….….…….…..…….….…….….…. 16
ЕР
Various ways of playback .................——.... eee... 17
Playing tracks repeatedly .........................0e0 DD DD 17
Emphasizing bass (DIGITAL MEGA BASS) ....................e0e 00... 18
Protecting your hearing (AVLS) essen ee 18
Checking the remaining time or the playing position ..................... 19
On the recorder ...........................ieemimecene ere RDA. 19
On the remote control .....................e......e.i ie ee ee 19
Locking the controls (HOLD) .......................e.eme cavernes 20
Connecting to a stereo system ……..……..….....…..rrrecnnnnnennnnnnsnnnnsmn 20
Editing recorded tracks .............. penounana nene nnnac anne na. 21
Erasing tracks ......................ee0m0 EEE RR EEE 21
To erase a track ………………nnannnnennnnmnmnnnnnenenn 21
To erase the whole disc .........................eeeieciic e ee reee eerece. 21
Adding a track mark ...................e..eiiee e De ee eee eee 22
Егазтр а track mark ....................e.ee eee eee 22
Moving recorded tracks esse EEE 23
On the recordet essen eee eee eee encens 23
On the remote contrOl essen EEE EEE De 23
Labeling recordinfS esse cece ees 24
On the recorder ........................eeeirieeriricec ccoo aace error rece sans 24
On the remote control .......................iieerirre nece e een renacer. 25
POWEr SOUFCES .................00suocssaeenensenane en cnsnencamacn es 27
Charging the nickel metal hydride rechargeable battery ................ 27
Using dry batteries ......................000 e DD DR e er eres 28
Additional information TR HERR 29
Precautions ........................iiieieiie rene eee eee eee eee eee eee eee ee eee eee eee, 29
Troubleshooting ............................... eee a ee es 31
System limitations ................. mv... Ree eee 33
MESSAGES coos etree eee e e reee reee reee eee 34
“ Specifications ....................eeemen in een Danone neon erre ere. 36
What is an MD? ........................eeiecereeceree eee reerecen ooo er erre. 37
Looking at the controls .............................eiee reee. 39
The sound will be sent from the connected equipment as analog
signal but will be recorded digitally on the disc. To record from a
digital source, see “Recording with digital input” (page 11).
Po Sd nl air RE J HE SL EL LL LN ER EE RE EET EEE EEE EEE Er IIT SE
a +
hols mE ree
1
R (red) Line cable
(RK-G129, not supplied)*
CD player,
cassette recorder,
etc. (source)
о
to a wall outlet
to LINE OUT L (white)
AC power adaptor
(supplied)
* Use the connecting cords
without an attenuator. To
connect to a portable CD player
having a stereo mini-jack, use
the RK-G136 connecting cord
(not supplied).
to LINE IN (OPTICAL)
(D Press OPEN and open the lid. @ Insert a recordable MD with the label side
facing up, and press the lid down to close.
ENE ESS SEERA SAAS EEE EES ESS SSE * EE SEE EE EEN EY SEES SS EEE EYE SEE E NEE EEE EEE
2 0 1 0 5 6 E 6 A a E A dE E IEEE EEE EEE EE EEE EEE EEE TETE EEE EEE EEE Essa.
dlr A nn A
- Fe Fre
>
A
т
...
rue Fu № &
ФБ.
vibra
Seer +
nee
un it
DD »
"e"
CA
..
L5
A
+
+
»
©
ED ”
rr
"e
-
i»
A
CD player, cassette
recorder, etc. (source)
Ч
vu
rir, PE LL SC SC BC ACE SL NCEE NEL Nu a Cru Sat a
LL EE EEE EN EEE ER EE EE EE ee U CE
ir.
"EEE AES SEER EEE ES EEA EEE ERY SSeS SES ES EYEE BE RSE NEY EE
Record an MD.
(1) Press and slide REC to the right .
“REC” lights up and recording starts.
(2 Play the CD or tape you want to
record.
To stop recording, press M.
“Data Save” or “Toc Edit” flashes while data
of the recording (the track's start and end
points, etc.) is being recorded. Do not move
or jog the recorder or disconnect the power
source while the indication is flashing in the
display.
To Press
Pause E
Press II again to resume recording.
Record from the end of the END SEARCH and slide REC.
previous recording
Record partway through the
previous recording.
p> ppl or << to find the start point
of recording and press IM to stop. Then
slide REC.
Remove the MD.
H and open the lid.”
» À track mark is added at the point where you press II; thus the remainder of the track will be
counted as a new track.
» Once you open the lid, the point to start recording will change to the beginning of the first track.
Check the point to start recording on the display.
If the recording does not start
* Make sure the recorder is not locked (page
20).
* Make sure the MD is not record-protected
(page 30).
* Premastered MDs cannot be recorded over.
Note
If the power supply is disrupted (i.e. the
battery is removed or becomes exhausted or
the AC power adaptor is disconnected)
when the recorder is operating, the lid will
not open until the power is restored.
* The level of the recorded sound is adjusted
automatically.
* You can monitor the sound during
recording. Connect the supplied
headphones with remote control to ©}
- REMOTE and adjust the volume by
pressing VOLUME +/- (VOL +/- on the
remote control). This does not affect the
recording level.
To use the recorder on d rechargeable battery or dry batteries, see
“Power Sources” (pages 27, 28).
rE тета Тала. бл Отт от "отт"... ,т.о то. ч навыков ванн нетто EUER EEE]
боб об обе oT ee a a a a tT Tt TT TL TL OL NT St Rt ENN Tree EE ERAN NEESER ERA NE REE EEE EEE AE EEE Em EE EEE EEE een eae eee eee a ee a "ee
POES OBESE =o NES EEE L ELSE EEE EES EAL Ena YEE eRe EE SEES ES SSeS ENE EE EE EE RE EEE EE EEE EE EEE EEE EE a en eae ee
lA A I VL mm ed = 7 mM WB BB Sm a 9 m 9 MOM SR BSR SEN SR E UE EE EU EU i iy Wh i Hf HF HE
a a a rr mm mamma LL LL EU EE EEE E e e e 7 E UE,
Di a wall outlet
to (REMOTE AC power adaptor
(supplied)
Headphones with a х
remote control to DC IN 3V
(supplied) .
Wear the earpiece
marked ® in your
right ear and the one
marked (D in your
left ear.
© Press OPEN and open the lid. (2) Insert an MD with the label side facing
up, and press the lid down to close.
(® Press > (Turn the control to
pp on the remote control).
A short beep sounds in the headphones
when you operate on the remote control.
(2) Press VOLUME (VOL on the remote
control) +/- to adjust the volume.
The volume will be shown in the display.
To stop play, press Ш.
A long beep sounds in the headphones when
you operate on the remote control.
To
Press (Beeps in the headphones)
Pause
II (Continuous short beeps)
Press II again to resume play.
Find the beginning of the current track
HE once (Turn the control to He on the
remote control)
(Three short beeps)
Find the beginning of the next track
Bi once (Turn the control to > »>>l on
the remote control)
(Two short beeps)
Go backwards while playing?
keep pressing 4d (Turn and hold the
control to 4d on the remote control)
Go forward while playing? keep pressing PI (Turn and hold the
control to B»- >» on the remote control)
Remove the MD MM and open the lid.”
9 To go backward or forward quickly without listening, press Il and keep pressing 44 or 1.
> Once you open the lid, the point to start play will change to the beginning of the first track.
If the play does not start
Make sure the recorder is not locked (page
20). |
When using optional headphones
Use only headphones with stereo mini plugs.
You cannot use headphones with micro
plugs.
Playback will switch automatically between
stereo and monaural according to the sound
source.
Notes
* The sound may skip during playback when
. the recorder is exposed to continuous
vibration, such as while jogging.
«If the power supply is disrupted (i.e. the
battery is removed or becomes exhausted
or the AC power adaptor is disconnected)
when the recorder is operating, the lid may
not open until the power is restored.
10
» Various ways of recording
|
Two ways of connecting to a sound source
The input jack of this recorder works as both digital and analog input jacks. Connect the
recorder to a CD player or a cassette recorder using either digital input or analog input. To
record, see “Recording with digital input” (page 11) to record using digital input, and
“Recording an MD right away!” (page 6) to record using analog input.
Difference between digital and analog inputs
Difference Input Digital input Analog (line) input
Connectable source Equipment with an optical Equipment with an analog
digital output jack (line) output jack
Usable cord Digital cable (with an optical Line cable (with 2 phono
or an optical-mini plug) plugs or a stereo-mini plug)
Signal from the source Digital Analog
Even when a digital source
(such as a CD) is connected,
the signal sent to the recorder
is analog.
Recorded track Marked (copied) Marked automatically
numbers automatically * after more than 2 seconds
*at the same positions asthe of blank or low-level
— source. segment.
» when the recorder is paused * when the recorder is paused
while recording. while recording.
You can erase unnecessary YOu can erase unnecessary
marks after recording marks after recording
(“Erasing a track mark”, (“Erasing a track mark”, page
page 22). 22).
Recorded sound level Same as the source Adjusted automatically. Can
also be adjusted manually
(“Adjusting the recording
level manually”, page 13).
Note
Track marks may be copied incorrectly :
*when you record from some CD players or multi disc players using ; digital input.
when the source is in shuffle or program play mode while recording using digital input. In this
case, play the source in normal play mode. |
*when recording BS or CS programs through digital input.
Recording with digital
input (optical cable
required)
Connect to a digital source using an
optical cable (POC-5B or POC-5AB, not
supplied) to make digital recordings.
Digital recording is possible even from
digital equipment with different sampling
rates, such as a DAT deck or a BS tuner,
using the built-in sampling rate converter.
Notes
* You can make a digital recording only from an
optical type output.
* When recording from a portable CD player,
play it on AC power and disable the anti-skip
function (such as ESP”.
* Digital output may be disabled on some
portable CD players when the player is not run
on AC power.
* Electronic Shock Protection
CD player, MD
player, digital
amplifier, etc.
Portable CD
player, etc.
$ Optical
Optical = mini-
plug POC-5B etc. plug
(not supplied)
POC-5AB etc.
(not supplied)
a
A Bl
to LINE IN Q = :
(OPTICAL) NI ~
GT
1 Insert a recordable MD and start
recording.
For recording operations, see
“Recording an MD right away !”
(page 6). To record from a portable
CD player, set the CD player to pause
and then start recording.
LINE IN (OPTICAL) jack is for both
digital and analog input
The recorder automatically recognizes the
type of line cable and switches to digital or
analog input.
To start/stop recording in
sync with the source player
(Synchro-recording)
You can easily make digital recordings of
a digital source on an MD.
Before synchro-recording, make
connections to the digital source with a
digital cable, and insert a recordable MD.
CD players,
etc. SYNCHRO REC
1 Slide SYNCHRO REC to ON.
“SYNC” appears in the display.
End 897
Ava, SYNC 1 1 HM
Ya Ei E EI
AAA IA II)
\
177i]
2 Press and slide REC to the right.
The recorder stands by for recording.
3 Play the source sound.
The recorder starts recording when it
receives the playing sound.
continued
11
12
To stop recording, press №.
e
*You cannot pause manually during
synchro-recording.
* When there is no sound from the player for
more than 3 seconds during synchro-
recording, the recorder goes into the
standby mode automatically. When the
sound comes from the player again, the
recorder resumes synchro-recording. If the
recorder is kept in the standby mode for 5
minutes or longer, the recorder stops
automatically.
Notes
* Do not switch SYNCHRO REC after step 2.
Recording may not be done properly.
* When recording in monaural, follow steps
1 and 2 of “Recording in monaural for
double the normal recording time” (page
13) before synchro-recording .
* Even when there is no recorded sound on
the sound source, there may be cases when
recording does not pause automatically
during synchro-recording due to the noise
level emitted from the sound source.
MM———]] ———;;—;——É[;;;;—;——;——],——]——lg”——s[]];].—l;]
Recording from a
microphone
Connect a stereo microphone (ECM-717,
ECM-MS907, ECM-MS957, etc.; not
supplied) to the MIC (PLUG IN POWER)
jack.
Stereo microphone
to MIC
(PLUG IN
POWER)
ell JU
NE
LL 5 À
2
—
MIC SENS (at the bottom)
1 Select the sensitivity with MIC SENS
(at the bottom of the recorder) .
Usually, set it to HIGH. When
recording loud sounds such as a live
concert, set it to LOW.
2 Insert a recordable MD and start
recording.
Press and slide REC to the right.
“REC” lights up and recording starts.
For other operations, see “Recording
an MD right away!” (page 6).
Notes
* You cannot record through the microphone
while an optical cable is connected to the
LINE IN (OPTICAL) jack. The recorder
automatically switches input in the
following order; optical input, microphone
input, and analog input.
* The microphone may pick up the operating
sound of the recorder itself. Use the
microphone away from the recorder in
such cases.
FE EE
Recording in monaural
for double the normal
recording time
For longer recordings, choose to record in
monaural. The recording time becomes
double the normal.
MODE In
1 While pressing Il, press and slide
REC to the right.
The recorder stands by for recording.
2 Press MODE.
"Mono REC” appears in the display,
and the recorder switches to
monaural recording.
Press MODEL again to record in
stereo. |
3 Press II again to start recording.
4 Play the sound source.
To stop recording, press №.
The recorder switches back to stereo
recording when you record the next time.
Notes
* [f you record a stereo source in monaural,
the sounds from left and right will be
mixed. |
* You cannot record in monaural if
SYNCHRO REC is slid to ON.
* The MDs recorded in monaural can be
played back only with an MD player/
recorder that has the monaural playing
function.
+ Sound recorded through digital input can
be monitored in stereo through
headphones, etc.
A
Adjusting the recording
level manually
(Manual recording)
When you record with an analog input,
the sound level is adjusted automatically.
If necessary, you can set the level
manually.
iH REC
1 While holding down I, press and
hold REC to the right for more than 2
seconds.
“ManualREC” appears and the
recorder stands by for recording.
To return to the automatic control,
while the recorder is in standby
mode, press and hold REC to the
right again for more than 2 seconds.
Manual REC
LZÉA
© & 8 8
aa их A oo FUI FT rire
pa: e ==: Li - Li Ch
2, Play the source.
ps
continued
13
14
3 While observing the level meter in
the display, adjust the recording level
by pressing »>»1 (+) or He< (>).
Set the level so that it hits the -12dB
at maximum input level.
Volume decreases increases
—
FECEHE 1+
=
5 = > |
TE E > Го = 7 vo
“Va vase” Li LH j
Note
Adjust the recording level while the
recorder is in standby mode. You
cannot adjust it while recording.
4 Press Il again to start recording.
To stop recording, press M.
The recording level control is switched back
to automatic control when you record the
next time.
When you record with microphone input,
select the sensitivity with MIC SENS (page
12).
DL
Checking the remaining
time or the recording
position
You can check the remaining time, track
number, etc. when recording or during
stop.
On the recorder
DISPLAY
REC indicator
1 Press DISPLAY while recording or in
stop mode. Each time you press the
button, the display changes as
follows. |
While recording
© ©
Track number
Elapsed time
Track number Remaining time for
recording
Current date? Current time?
Y Appears only when the clock is set.
In stop mode
© ©
Track number
Elapsed time
Track name? Remaining time for
8
recording
Disc name” Remaining time
after the current
location
Current date” Current time”
"Appears only if the track has been labeled.
9 Appears only when the clock is set.
On the remote control
DISPLAY
1 Press DISPLAY while recording or in
stop mode. Each time you press the
button, the display changes as
follows.
Cor TT — _
ail on 31 [5 : => REC |
©
©
While recording
O ©
Elapsed time
Track number
Remaining time
for recording
Track number
In stop mode
O
©
Track number
Elapsed time
Track number
Track name?
Number of tracks
in the disc
Disc name?
Current time?
UAppears only if the track has been labeled.
4 Appears only when the clock is set.
To know the recording condition
The REC indicator lights up or flashes
according to the recording condition.
Recording
condition
REC indicator
While recording
lights up
flashes according to
the loudness of the
source while
recording with a
microphone (voice
mirror)
Recording standby
flashes
— | Current time?
I Appears only when the clock is set.
Less than 3
minutes’ recording
time available
flashes slowly
A track mark has goes off
been added momentarily
©
If you want to check the playing position or
track name while playing, see page 19.
15
16
FE Ta
Setting the clock to
stamp the recorded
time
To stamp the date and time on the MD
when you record, you first need to set the
clock.
CLOCK SET
(at the bottom)
1 Connect the power source.
Use the supplied AC power adaptor.
2 Press CLOCK SET at the bottom of
the recorder.
Use a pointed object.
The digits of the year flash.
Ч im 1d
2
To DATE Za
AE AM THAT
Pat” IL "LILI
I PIE DN BS EC CC)
3 Change the current year by pressing
He or PP.
To change the digits rapidly, keep
pressing FH. or PP.
4 Press Be to enter the year.
The digit of the month flashes.
5 Repeat steps 3 and 4 to enter the
current month, date, hour, and
minute.
When you press PP to enter the
minute, the clock starts operating.
If you make a mistake while
setting the clock
Press IM, and set the clock again from step
2. You can skip a step by pressing ==.
To display the current time
When the recorder is not operating or
while recording, press DISPLAY
repeatedly until the current time appears
in the display.
To display the time in the 24-
hour system
While setting the clock, press DISPLAY.
To display the time in the 12-hour system,
press DISPLAY again.
Charging the built-in battery for the
clock
When you use the recorder for the first time
or after a long period of disuse, charge the
built-in battery. After setting the clock, leave
the recorder connected to the AC power for
about 2 hours to charge the built-in battery.
Once charged, the built-in battery should last
about a month without connecting to any of
the power sources. The recorder will
automatically charge the built-in battery
while connected to AC power, dry batteries
or a rechargeable battery.
» Various ways of
playback
FE
Playing tracks
repeatedly
You can play tracks repeatedly in three
ways — all repeat, single repeat, and
shuffle repeat.
MODE
1 Press MODE (PLAY MODE on the
remote control) while the recorder is
playing an MD.
Each time you press the button, the
“ play mode indication changes as
follows.
Ex; Display on the main unit
984
<
rr 5 vu co
ox = hl LOLA
pe E VU — [— |
Play mode indication
Indication Play mode
none All the tracks are
(normal play) played once.
‘SC All the tracks are
(all repeat) played repeatedly.
‘ST A single track is
(single repeat) played repeatedly.
CG SHUF” All the tracks are
(shuffle repeat) played repeatedly in
random order.
17
18
|
Emphasizing bass
(DIGITAL MEGA BASS)
Mega Bass function intensifies low
frequency sound for richer quality audio
reproduction. It affects only thesound
from the headphones.
DIGITAL MEGA BASS
1 Press DIGITAL MEGA BASS.
Each time you press DIGITAL MEGA
BASS, the Mega Bass indication
changes as follows.
Mega Bass indication
SHE
=
wl
Indication Play mode
none Normal play
“BASS CI” Mega Bass
(moderate effect)
"BAS CC]
Mega Bass (strong
effect)
Notes
«If the sound becomes distorted when
emphasizing bass, turn down the volume.
* Mega Bass function does not affect the
sound being recorded.
* Mega Bass does not function when a line
cable is connected to the LINE OUT jack on
the recorder.
DB.
Protecting your hearing
(AVLS)
The AVLS (Automatic Volume Limiter
System) function keeps down the
maximum volume to protect your ears.
AVLS
1 Set AVLSat the bottom of the
recorder to LIMIT.
When you try to turn the volume too
high, “AVLS” appears in the display.
The volume is kept to a moderate
level.
A.
Checking the remaining
time or the playing
position
You can check the track name, disc name,
etc. during playback. >
On the recorder
DISPLAY
Я Press DISPLAY while playing.
Each time you press DISPLAY, the
display changes as follows.
O
©
© ©
Track number
Elapsed time
Track name? Remaining time of
the current track
Disc name” Remaining time
after the current
location
Recorded date? Recorded time?
Appears only if the track has been labeled.
9 Appears only when the clock is set.
On the remote control
DISPLAY
1 Press DISPLAY while playing.
Each time you press DISPLAY, the
display changes as follows.
O O
=
<= |
HB
tt
O ©
Track number
Elapsed time
Track number Track name?
The number of Disc name!
tracks in the disc
— Recorded time”
Appears only if the track has been labeled.
4 Appears only when the clock is set.
If you want to check the remaining time or
the recording position while recording or in
stop mode, see page 14.
19
20
A
Locking the controls
(HOLD)
To prevent the buttons from being
accidentally operated when you carry the
recorder, use this function. *-
HOLD
1 Slide HOLD in the direction of the
— - -
On the recorder, slide HOLD to lock
the controls of the recorder. On the
remote control, slide HOLD to lock
the controls of the remote control.
Slide HOLD in the opposite direction
of the arrow to unlock the controls.
E
Connecting to a stereo
system
Connect the LINE OUT jack of the
recorder to the LINE IN jacks of an
amplifier or a tape player with a line cable
(RK-G129 or RK-G136, not supplied). The
output is analog. The recorder plays the
MD digitally and sends analog signals to
the connected equipment.
Portable DAT || Stereo
recorder system, etc.
to LINE IN
2 phono plugs
Stereo .
mini-plug f| R L (white)
(red)
RK-G136 RK-G129
(not (not
supplied) supplied)
\ >
Cu CAC na E
A
|
"e
1
OS
Note
The Mega Bass does not function or will be
cancelled when the LINE OUT jack is
connected with a line cable.
> Editing recorded tracks
You can edit your recordings by adding/
erasing track marks or labeling tracks and
MDs. Premastered MDs cannot be edited.
Notes on editing
* Do not move or jog the recorder while “Toc
Edit”* is flashing in the display.
* You cannot edit tracks on an MD that is
record-protected. Before editing tracks,
close the tab on the side of the MD.
*TOC = Table of Contents
HE
Erasing tracks
To erase a track
Note that once a recording has been
erased, you cannot retrieve it. Make sure
of the track you are erasing.
EDIT/ENTER
T MARK
1 Press EDIT/ENTER while playing
the track you want to erase.
" Je : Name” flashes in the display,
and the recorder plays the selected
track repeatedly.
2 Press € or Dl repeatedly until
” Je : Erase” flashes in the display.
3 Press EDIT/ENTER again.
"Erase OK?” and "Push ENTER”
appear alternately in the display.
To cancel erasing, press M or
T MARK.
To erase a part of a track
Add track marks at the beginning and the
end of the part you want to erase, then
erase the part.
To erase the whole disc
You can quickly erase all the tracks and
data of the MD at the same time.
Note that once a recording has been
erased, you cannot retrieve it. Be sure to
check the contents of the disc you want to
erase.
T MARK
1 Press EDIT/ ENTER on the recorder.
2 Press 4d or PP» repeatedly until
” Cy : Erase” flashes in the display.
3 Press EDIT/ENTER again.
"All Erase?” and "Push ENTER”
appear alternately in the display.
To cancel erasing, press IN or
T MARK.
4 Press EDIT/ENTER again.
"Toc Edit” flashes in the display, and
all the tracks will be erased.
When erasing is complete, "BLANK
DISC” appears in the display.
21
Adding a track mark
You can add track marks so that the part
after the new track mark is counted as a
new track.
The track numbers will increase as
follows.
_—__;— ==
| 1 #2] 3 4
1 While playing or pausing an MD,
press T MARK on the recorder at the
point you want to mark.
“MARK ON” appears in the display,
and a track mark is added. The track
number will increase by one.
To add track marks while
recording
Press T MARK on the recorder or TRACK
MARK on the remote controi.
Note
TRACK MARK on the remote control does
not function during playback.
EE
Erasing a track mark
When you record with analog (line) input,
unnecessary track marks may be recorded
where recording level is low. You can
erase a track mark to combine the tracks
before and after the track mark. The track
numbers will change as follows.
[1 ESSE) a
3 Erase a track mark
EE: = 3
Track numbers decrease
<< Il
T MARK
1 While playing the track with the track
mark you want to erase, press II to
pause.
2 Find the track mark by pressing 14<
slightly.
For example, to erase the third track
mark, find the beginning of the third
track. “00:00” appears in the display.
3 Press T MARK to erase the mark.
“MARK OFF” appears in the display.
The track mark is erased and the two
tracks are combined.
When you erase a track mark, the date, time,
and name assigned to the mark are also
erased.
E
Moving recorded tracks
You can change the order of the recorded
tracks.
Before moving
Track A TrackB TrackC TrackD
| 1 E 4
Move track C
from the third to
After the second track.
moving
Track A Track C Track B Track D
Г 1 РЕ a
On the recorder
HE >>! EDIT/ENTER
1 Press EDIT/ENTER while playing
the track you want to move.
— J@ : Name” flashes in the display
and the recorder plays the selected
track repeatedly.
2 Press 4d or PP» repeatedly until
” Je : Move” flashes in the display.
3 Press EDIT/ENTER again.
For the example above, “MV 003 —
003” appears in the display.
4 Press 4d or PP repeatedly to select
the destination track number.
For the example above, “MV 003 —
002” appears in the display.
To cancel moving, press M ог
T MARK.
5 Press EDIT/ENTER again.
The track moves to the selected
destination track.
On the remote control
DISPLAY
so Control
1 Press DISPLAY for 2 seconds or more
While playing the track you want to
move.
” Je : Name” flashes in the display
and the recorder plays the selected
track repeatedly.
2 Turn the control until ” oo : Move”
appears in the display.
3 Press M. |
For the example above, “MV 003 —
003” appears in the display.
4 Turn the control to select the
destination track number.
For the example above, “MV 003 —
002” appears in the display.
To cancel moving, press TRACK
MARK.
5 Press IN again.
The selected track moves just before
the destination track.
23
DL
Labeling recordings
You can name tracks during playback,
discs during stop, and both during
recording. Each name can be as long as
200 letters. ne
Each disc can hold up to 1700
alphanumeric letters during playback or
stop, and 500 alphanumeric letters during
one recording.
On the recorder
MODE
DISPLAY
Labeling a disc during stop
1 - Insert a disc.
To label a disc that is already in the
recorder, press IM to stop.
2 Press EDIT/ ENTER.
“ Ey : Name” flashes in the display.
3 Press EDIT/ENTER again.
The disc is ready to be labeled.
4 Press HE or PP repeatedly to select
a letter and press Be to enter.
The selected letter stops flashing and
the cursor moves to the next input
position.
Press To
и Switch between capital
letters, small letters, and
marks / numbers.
VOLUME +/- Move the cursor to the
left or right.
<< / >>! Change the letter to the
one before / next one.
DISPLAY Insert a blank space to
type in a new letter.
MODE Delete a letter and move
back all following letters
to the left.
N Cancel labeling.
T MARK Cancel labeling.
5 Repeat step 4 and enter all characters
of the label name.
6 Press EDIT/ENTER.
The track or disc is labeled.
Labeling a track during playback
1 Insert a disc and play the track you
want to label.
2 Press EDIT/ENTER.
> Je : Name” flashes in the display.
3 Press EDIT/ ENTER again.
The track is ready to be labeled.
a Follow steps 4 to 6 of "Labeling a disc
during stop” above.
Labeling a track or a disc during
recording
1 Press EDIT/ENTER during
recording.
” Je : Name” flashes in the display.
2 To label a track, press EDIT/ENTER
again.
To label a disc, press 44 or >>]
repeatedly until ” 6y : Name”
flashes in the display, then press
EDIT/ENTER.
3 Follow steps 4 to 6 of "Labeling a disc
during stop” above.
To cancel labeling, press B or T MARK.
Note
When the recording is stopped while
labeling a track or a disc during
recording, or when the playback moves
on to the next track while labeling a track,
the input at that point is entered
automatically.
On the remote control
DISPLAY
PLAY MODE
i
> Control
Labeling a disc during stop
1 Insert a disc.
To label a disc that is already in the
recorder, press IM to stop.
2 Press DISPLAY for 2 seconds or
more.
” 6) : Name” flashes in the display.
3 Press M.
The disc is ready to be labeled.
4 Turn the control to select a letter and
press IM to enter.
The selected letter stops flashing and
the cursor moves to the next input
position.
Press/ Turn To
Il Switch between capital
letters, small letters, and
marks / numbers.
VOL +/- Move the cursor to the
left or right.
HE /p pp] Change the letter to the
one before / next one.
Insert a blank space to
type in a new letter.
PLAY MODE Delete a letter and move
back all following letters
to the left.
TRACK MARK Cancel labeling.
DISPLAY
continued
25
26
5 Repeat step 4 and enter all characters
of the label name.
6 Keep pressing the IM for 2 seconds or
more.
The track or disc is labeled.
м -
Labeling a track during playback
1 Insert a disc and play the track you
want to label.
2 Press DISPLAY for 2 seconds or
more.
” Je : Name” flashes in the display.
3 Press M.
The track is ready to be labeled.
4 Follow steps 4 to 6 of "Labeling a disc
during stop” above.
Labeling a track or a disc during
recording
1 Press DISPLAY for 2 seconds or more
during recording.
” e : Name” flashes in the display.
2 To label a track, press M. .
To label a disc, turn the control to
HE or > «PP until ” Ey : Name”
‘flashes in the display, then press IN.
3 Follow steps 4 to 6 of "Labeling a disc
during stop” above.
To cancel labeling, press TRACK MARK.
Note
When the recording is stopped while
labeling a track or a disc during
recording, or when the playback moves
on to the next track while labeling a track,
the input at that point is entered
automatically.
Available characters
* Capital and small letters of the English
alphabet
* Numbers O to 9
+ 1!" #$%&()*.;<=>?
@ _` + -', / : _ ($расе)
To relabel recordings
Follow the steps corresponding to the
labeling method until the disc or track is
ready to be labeled. Enter a new character
over the one you want to change, then
press EDIT/ENTER (keep pressing IN for
2 seconds or more on the remote control).
Notes
* You cannot relabel premastered MDs or
label MDs that have not been recorded.
* The recorder is able to display, but cannot
label using, Japanese “Katakana”
characters.
» Power sources
You can use the recorder on house current
or as follows.
In the recorder ...
— a nickel metal hydride rechargeable
battery NH-14WM (supplied)
With supplied battery case ...
—- two LR6 (size AA) alkaline batteries
(not supplied)
It is preferable to use the recorder on
house current when recording for a long
time.
Ш
Charging the nickel
metal hydride
rechargeable battery
Before using the supplied NH-14WM
nickel metal hydride rechargeable battery
for the first time, charge it in the recorder.
1 Connect the supplied AC power
adaptor. 0
to wall outlet
AC power adaptor
(supplied)
to DC IN 3V
2 Insert the NH-14WM into the
recorder and close the lid.
oo B/CHARGE
3 Press B/CHARGE.
“charging” flashes, CT appears in the
display, and charging starts.
(227
x
77]
Full charging of a completely
discharged rechargeable battery takes
about 3 hours. To cancel charging,
press N/ CHARGE.
Notes
* Be sure to use the supplied AC power
adaptor.
*Charging time may vary depending on the
battery condition.
* When a rechargeable battery is charged for
the first time or charged after a long period
of disuse, battery life may be shorter than
usual. Repeat discharging and recharging a
few times. The battery life should return to
normal.
*When the battery life of a fully charged
rechargeable battery becomes about half
the normal life, replace it. |
* When carrying the rechargeable battery,
keep it in the supplied carrying case. It is
dangerous to carry the battery out of its
case in your pocket or a bag together with
metallic objects such as key rings, as this
may cause a short circuit.
- Remove the rechargeable battery from the
recorder when it is not to be used for a long
time. |
27
Using on a nickel metal hydride
rechargeable battery
Be sure the rechargeable battery is fully
charged.
1 Insert the fully charged nickel metal
hydride rechargeable battery with
‘correct polarity.
Using dry batteries
1 Attach the supplied battery case.
2 Insert two LRG (size AA) dry batteries
(not supplied) with correct polarity.
Battery life”
Batteries Recording? + Playback
NH-14WM Approx. Approx.
nickel metal 2.5 hours 4 hours
hydride
rechargeable
battery
TwoLR6 ~~ ----- 9 Approx.
(size AA) 10 hours
Sony alkaline
dry batteries
NH-14WM — —-—- 9 Approx.
nickel metal 16 hours
hydride
rechargeable
battery
+ Two LR6
(size AA)
The battery life may be shorter due to
operating conditions and the temperature
of the location.
4 When you record, use a fully charged
rechargeable battery.
¥ Recording time may differ according to the
alkaline batteries.
When to replace the batteries
When the dry batteries or rechargeable
battery are weak, flashing 2 or “LOW
BATT" appears in the display. Replace
the dry batteries or charge the
rechargeable battery.
Notes
* Do not use a new dry battery mixed with
an used one. Do not mix different types of
dry batteries.
* Stop the recorder before replacing batteries.
* When replacing the dry batteries, replace
both batteries with new ones.
* The recorder does operate with one dry
battery but may not operate properly;
always use two dry batteries.
> Additional information
Me a —ccommm.a ”h”a;.”.;.;.:;OÁóm |
Precautions
On safety
Do not put any foreign objects in the DC
IN 3 V jack.
64e —
On power sources
» Use house current, nickel metal
hydride rechargeable battery, two LR6
(size AA) batteries, or car battery.
+ For use in your house: Use the AC
power adaptor supplied with this
recorder. Do not use any other AC
power adaptor since it may cause the
recorder to malfunction.
Polarity of
‘the plug
* The recorder is not disconnected from
the AC power source (mains) as long
as it is connected to the wall outlet,
even if the recorder itself has been
turned oft.
+ If you are not going to use this recorder
for a long time, be sure to disconnect
the power supply (AC power adaptor,
dry batteries, rechargeable battery, or
car battery cord). To remove the AC
power adaptor from the wall outlet,
grasp the adaptor plug itself; never
pull the cord.
+ For use in the car: Use the CPA-9 car
connecting pack and the DCC-E230 car
battery cord (not supplied).
On heat build-up
Heat may build up in the recorder if it is
used for an extended period of time. In
this case, leave the recorder turned off
until it cools down.
On installation
* Never use the recorder where it will be
subjected to extremes of light,
temperature, moisture or vibration.
* Never wrap the recorder in anything
when it is being used with the AC
power adaptor. Heat build-up in the
recorder may cause malfunction or
damage.
On the headphones
Road safety
Do not use headphones while driving,
cycling, or operating any motorized vehicle.
It may create a traffic hazard and is illegal in
many areas. Ît can also be potentially
dangerous to play your recorder at high
volume while walking, especially at
pedestrian crossings. You should exercise
extreme caution or discontinue use in
potentially hazardous situations.
Preventing hearing damage
Avoid using headphones at high volume.
Hearing experts advise against continuous,
loud and extended play. If you experience a
ringing in your ears, reduce the volume or
discontinue use.
Caring for others
Keep the volume at a moderate level. This
will allow you to hear outside sounds and to
be considerate of the people around you.
On the MiniDisc cartridge
* When carrying or storing the MiniDisc,
keep it in its case.
* Do not break open the shutter.
* Do not place the cartridge where it will
be subject to light, extreme
temperatures, moisture or dust.
On cleaning
* Clean the recorder casing with a soft
cloth slightly moistened with water or
a mild detergent solution. Do not use
any type of abrasive pad, scouring
powder or solvent such as alcohol or
benzene as it may mar the finish of the
casing. |
* Wipe the disc cartridge with a dry cloth
to remove dirt.
* Dust on the lens may prevent the unit
from operating properly. Be sure to
close the disc compartment lid after
inserting or ejecting an MD.
29
30
Notes on batteries
Incorrect battery usage may lead to
leakage of battery fluid or bursting
batteries. To prevent such accidents,
observe the following precautions:
* Install the + and - poles of the batteries
correctly. N
* Do not install new and used batteries
or different kinds of batteries together.
* Do not try to recharge dry batteries.
* When the recorder is not to be used for
a long time, be sure to remove the
batteries.
* Tfa battery leak should develop,
carefully and thoroughly wipe away
battery fluid from the battery
compartment before inserting new
ones.
Note on mechanical noise
The recorder gives off mechanical noise
while operating, which is caused by the
power-saving system of the recorder and
it is not a problem.
To protect a recorded MD
To record-protect an MD, slide open the
tab at the side of the MD. In this position,
the MD cannot be recorded. To record
again, slide the tab back so the tab is
Visible.
Back of the MD
Record-protect
Note on digital recording
This recorder uses the Serial Copy
Management System, which allows only
first-generation digital copies to be made
from premastered software. You can only
make copies from a home-recorded MD
by using the analog (line out) connections.
CD player, MD
player, etc.
3 Digital recording
HLL
Home- No Recordable
recorded digital MD
MD recording
If you have any questions or problems
concerning your recorder, please consult
your nearest Sony dealer. (If a trouble
occurred when the disc was in the
recorder, we recommend that the disc be
left in the recorder when you consult your
Sony dealer so that the cause of trouble
may be better understood.)
FE " " — " " _ _—_—_—— "mm" —" " " " " " "=
Troubleshooting
Should any problem persist after you have made these checks, consult your nearest Sony
dealer.
Symptom Cause/Solution
The recorder does not * Audio sources may not be securely connected.
work or works =» Disconnect the audio sources once and connect them again
poorly. (pages 6,11).
* The HOLD function is turned on ( HOLD” appears in the display
When you press an operation button on the recorder).
= Disable HOLD by sliding the HOLD switch in the opposite
direction of the arrow (page 20).
* Moisture has condensed inside the recorder.
=» Take the MD out and leave the recorder in a warm place for
several hours until the moisture evaporates.
* The rechargeable battery or dry batteries are weak (£ 1 or
“LOW BATT” flashes).
=» Charge the rechargeable battery or replace the dry batteries
(pages 27, 28).
» The rechargeable battery or dry batteries have been installed
incorrectly.
= Install the batteries correctly (page 27, 28).
* You pressed a button while the disc indication was rotating
quickly.
> Wait until the indication rotates slowly.
“ When recording digitally from a portable CD player, you did not
use AC power or did not disable the anti-skip function such as
+ = ESP (page 1i).
* The analog recording was made using a connecting cord with an
attenuator.
> Use a connecting cord without an attenuator (page 6).
* The AC power adaptor was unplugged during recording or a
power outage occurred.
* While operating, the recorder received a mechanical shock, too
much static, abnormal power voltage caused by lightning, etc.
= Restart the operation as follows.
1 Disconnect all the power sources.
2 Leave the recorder for about 30 seconds.
3 Connect the power source. ; |
* The disc is damaged or does not contain proper recording or
editing data. |
= Reinsert the disc. If this fails, rerecord.
continued
31
TUU a
Symptom
Cause/Solution
No sound comes
through the
headphones.
* The headphones plug is not firmly connected.
=» Plug in the plug of the headphones firmly to the remote
control. Plug in the plug of the remote control firmly to
()/REMOTE.
+ Volume is too low.
> Adjust the volume by pressing VOLUME +/- (VOL +/- on
the remote control).
* AVLS is on.
> Slide AVLS to NORM (page 18).
An MD is not played
from the first track.
* Disc playing stopped before it came to the last track.
+ Press 4d repeatedly or open and close the lid once to go
back to the beginning of the disc, and restart playing after
checking the track number in the display.
Playback sound skips.
* The recorder is placed where it receives continuous vibration.
= Put the recorder on a stable place.
* A very short track may cause sound to skip.
Sound has a lot of
static.
* Strong magnetism from a television or such device is interfering
with operation.
= Move the recorder away from the source of strong
magnetism.
Cannot find the track * You pressed I after pressing HE< or >.
marks. =» Press II before pressing 4d or Ppl.
The rechargeable * The rechargeable battery has been inserted incorrectly or the AC
battery does not start
charging.
.- power adaptor has been connected incorrectly.
> Insert the battery correctly or connect the AC power adaptor
correctlv.
The clock loses time
or the display flashes.
The recording date
was not stamped onto
the disc.
* The built-in battery for the clock is weak.
> Connect the AC power adaptor to DC IN 3 V on the recorder
and the wall outlet to charge the built-in battery. After
charging, set the clock again (page 16). Note that the clock
may gain or lose up to about 2 minutes per month under
normal condition.
The lid does not
open.
* The power sources have been disconnected during recording or
editing, or the batteries have been exhausted.
=» Set the power sources again, or replace the exhausted
batteries with new ones.
ZZ z—_ _ _—_"—_ " "__————————"—"— —" "_"_" "_ " " " "—" — - _ " " " " " "— — —_ "_" " " _ " " "—"— "1"
System limitations
The recording system in your MiniDisc recorder is radically different from those used in
cassette and DAT decks and is characterized by the limitations described below. Note,
however, that these limitations are due to the inherent nature of the MD recording system
itself and not to mechanical cayses.
Symptom
Cause
“TR FULL” appears
even before the disc
has reached the
maximum recording
time (60 or 74
minutes).
When 254 tracks have been recorded on the disc, “TR FULL”
appears regardless of the total recorded time. More than 254 tracks
cannot be recorded on the disc. To continue recording, erase
unnecessary tracks.
“TR FULL” appears
even before the disc
has reached the
maximum track
number or recording
time.
Repeated recording and erasing may cause fragmentation and
scattering of data. Although those scattered data can be read, each
fragment is counted as a track. In this case, the number of tracks
may reach 254 and further recording is not possible. To continue
recording, erase unnecessary tracks.
Track marks cannot
be erased.
The remaining
recording time does
not increase even
after erasing
numerous shart
tracks. 7
When the data of a track is fragmented, the track mark of a
fragment under 12 seconds long cannot be erased. You cannot
combine a track recorded in stereo and a track recorded in
monaural; nor can you combine a track recorded with digital
connection and a track recorded with analog connection.
Tracks of under 12 seconds in length are not counted and so erasing
them may not lead to an increase in the recording time.
The total recorded
time and the
remaining time on the
disc may not total the
maximum recording
time (60 or 74
Normally, recording is done in minimum units of approximately 2
seconds. When recording is stopped, the last unit of recording
always uses this unit of 2 seconds even if the actual recording is
shorter. Likewise, when recording is restarted after the stop, the
recorder will automatically insert a blank space amounting to 2
seconds before the next recording. (This is to prevent accidental
minutes). erasing of a previous track whenever a new recording is started).
Therefore, the actual recording time will decrease whenever a
recording is stopped; a maximum of 6 seconds compared to the
potential recording time for each stop.
The edited tracks may The fragmentation of data may cause sound dropout while
exhibit sound
dropout during
search operations.
searching because the tracks are played in higher speed than
normal playback.
33
I
Messages
If the following error messages flash in the display window, check the chart below.
Error message Meaning/Remedy
BLANK DISC * An MD with no recording on it is inserted.
+ Insert a recorded MD.
DISC ERR * The disc is damaged or does not contain proper recording or
editing data.
» Reinsert the disc. If this fails, rerecord.
DISC FULL There is no more space to record on the disc (less than 12 seconds
available).
» Replace the disc.
Data Save The MD player is recording information (sounds) from the memory
to the disk.
» Wait until this process is completed. Do not expose the player
to any physical shock, nor disrupt power supply.
Toc Edit The MD player is recording information (track start and end
position) from the memory to the disk.
+ Wait until this process is completed. Do not expose the player
to physical shock, nor disrupt power supply.
BUSY You tried to operate the recorder while it was accessing the
recorded data.
» Wait until the message goes out (in rare cases, it may take 2-3
minutes).
NAME FULL You tried to enter more than 200 letters to label a single track or
disc. |
You tried to enter a total of more than 1700 letters for track or disc
names during playback or stop.
You tried to enter a total of more than 500 letters for track or disc
names during a single recording.
+ Enter the characters within the limit.
Hi DC in Voltage of the power supply is too high (The supplied AC power
adaptor or the recommended car battery cord is not used).
» Use the supplied AC power adaptor or the recommended car
battery cord.
HOLD The recorder is locked.
» Slide HOLD against the arrow to unlock the recorder (page 20).
LOW BATT Batteries are weak.
‚ ® Charge the rechargeable battery or replace the dry batteries
‘ (pages 27, 28).
MEM OVER You tried to record when there is no indication in the display, with
the recorder placed where it receives continuous vibration.
» Put the recorder on a stable place, and start recording again.
Error message Meaning/Remedy
NO COPY + You tried to make a copy from a disc that is protected by the Serial
Copy Management System. You cannot make copies from a
digitally connected source which was itself recorded using digital
connection.
= Use analog connection instead (page 6).
NO DISC * You tried to play or record with no disc in the recorder.
> Insert an MD.
NO SIGNAL * The recorder could not detect digital input signals.
> Make sure that the source is connected firmly (page 11).
P/B ONLY * You tried to record or edit on a premastered MD (P/B stands for
“playback”.)
+ Insert a recordable MD.
PROTECTED * You tried to record or edit on a MD with the tab in the record-
protect position.
= Slide the tab back (page 30).
SORRY * You tried to erase the track mark at the beginning of the first track.
* You tried to erase a track mark to combine tracks the recorder
cannot combine (a track recorded in stereo and in mono, for
example).
* You tired to press DIGITAL MEGA BASS when the LINE OUT jack
is plugged in.
* You tried to press II or T MARK during synchro-recording.
TEMP OVER * Heat has built up in the recorder.
‘= Let the recorder cool down.
TR FULL * There is no more space for new data when you are editing the MD.
= Erase unnecessary tracks (page 21).
TrPROTECT * You tried to record or edit on a track that is protected from erasing.
= “Record or edit on other tracks.
EDITING * You pressed a key on the recorder while editing on the remote
- control, or vice versa.
35
36
JE LL ;;,—]]]]í];]];;;—;————;;—;—]]——;— ¡All
Specifications
System
Audio playing system
MiniDisc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength: A = 780 nm
Emission duration: continuous
Laser output: less than 44.6 pW
(This output is the value measured at a
distance of 200 mm from the lens surface on
the optical pick-up block with 7 mm
aperture.)
Recording and playback time
Maximum 74 minutes (MDW-74, stereo
recording)
Maximum 148 minutes (MDW-74, monaural
recording)
Revolutions
400 rpm to 900 rpm (CLV)
Error correction
Advanced Cross Interleave Reed Solomon
Code (ACIRC)
Sampling frequency
44.1 kHz
Sampling rate converter .
Input: 32 kHz/44.1 kHz/48 kHz
Ceding
Adaptive TRansform Acoustic Coding
(ATRAC)
Modulation system :
EFM (Eight to Fourteen Modulation)
Number of channels
2 stereo channels
1 monaural channel
Frequency response
20 to 20,000 Hz + 3 dB
Wow and Flutter
Below measurable limit
Inputs
Microphone: stereo mini-jack, 0.22-0.78 mV
Line in: stereo mini-jack, 69-194 mV
Optical (Digital) in: optical (digital) mini-jack
Outputs
Headphones: stereo mini-jack, maximum
output level 5 mW+ 5 mW, load impedance
16 ohm
Line out: stereo mini-jack, 194 mV, load
impedance 10 kilohm
General
Power requirements
Sony AC Power Adaptor (supplied)
connected at the DC IN 3 V jack:
120 V AC, 60 Hz (US model)
230-240 V AC, 50/60 Hz (UK and Hong
Kong model)
240 V AC, 50/60 Hz (Australia and New
Zealand model)
Nickel metal hydride rechargeable battery
NH-14WM (supplied)
Two LR6 (size AA) alkaline batteries (not
supplied)
Battery operation time
See “Battery life” (page 28)
Dimensions
Approx. 78.9 x 18.9 x 84 mm (w/h/d)
(31/8 х 3/4 х 3 3/8 т.)
Mass
Approx. 147 g (5.2 oz) the recorder only
Approx. 190 g (6.7 oz) incl. a recordable MD,
and NH-14WM nickel metal hydride
rechargeable battery
Supplied accessories
AC power adaptor (1)
Headphones with a remote control (1)
NH-14WM nickel metal hydride
rechargeable battery (1)
Rechargeable battery carrying case (1)
Dry battery case (1)
Carrying pouch (1)
Optional accessories
Optical Cable
POC-151HG, POC-152HG, POC-MZI,
POC-MZ2, POC-15B, POC-15AB, POC-
DA12SP
Line Cable RK-G129, RK-G136
Car Connecting Pack, CPA-9
Car Battery Cord DCC-E230 hl
Stereo Microphones ECM-717, ECM-MS907,
ECM-MS957
Stereo Headphones* MDR-series
Active Speakers SRS-A41, SRS-A91
Recordable MDs MDW -series
MiniDisc Carrying Case CK-MD4
MiniDisc Filing Box CK-MD10
Your dealer may not handle some of the
above listed accessories. Please ask the
dealer for detailed information about the
accessories in your country.
US and foreign patents licensed from Dolby
Laboratories Licensing Corporation.
Design and specifications are subject to
change without notice.
* Whether you should plug the headphones
directly to ()/REMOTE on the main unit or
to a remote control, use only headphones
with stereo mini plugs-
stereo mini plugs
What is an MD?
How MiniDisc works
MiniDisc (MD) comes in two types:
premastered (prerecorded) and
recordable (blank). Premastered MDs,
recorded at music studios, can be played
back almost endlessly. However, they
can't be recorded on or over like cassette
tapes. To record, you must use a
‘recordable MD",
Premastered MDs
Premastered MDs are recorded and
played like regular CDs. A laser beam
focuses on the pits in the surface of the
MD and reflects the information back to
the lens in the recorder. The recorder then
decodes the signals and plays them back
as music.
Recordable MDs
Recordable MDs, which use magneto-
optical (MO) technology, can be recorded
again and again. The laser inside the
recorder applies heat to the MD,
demagnetizing the magnetic layer of the
MD. The recorder then applies a magnetic
field to the layer. This magnetic field
corresponds exactly to the audio signals
generated by the connected source. (The
north and south polarities equate to
digital "1" and "0".) The demagnetized
MD adopts the polarity of the magnetic
field, resulting in a recorded MD.
CF
37
How the MiniDisc got so small
The 2.5-inch MiniDisc, encased in a
plastic cartridge that looks like a 3.5-inch
diskette (see illustration above), uses a
new digital audio compression
technology called ATRAC (Adaptive
TRansform Acoustic Coding). Tq store
more sound in less space, ATRAC extracts
and encodes only those frequency
components actually audible to the
human ear.
Quick Random Access
Like CDs, MDs offer instantaneous
random access to the beginning of any
music track. Premastered MDs are
recorded with location addresses
corresponding to each music selection.
Recordable MDs are manufactured with a
“User TOC Area” to contain the order of
the music. The TOC (Table of Contents)
system is similar to the “directory
management system” of floppy disks. In
other words, starting and ending
addresses for all music tracks recorded on
the disc are stored in this area. This lets
you randomly access the beginning of any
track as soon as you enter the track
number (AMS), as well as label the
location with a track name as you would
a file on a diskette.
User TOC Area | un y Music Data s- na
Contains the order and start/end
points of the music.
Shock-Resistant Memory
One major drawback of optical read
systems is that they can skip or mute
when subjected to vibration. The MD
system resolves this problem by using a
buffer memory that stores audio data.
Looking at the controls
See pages in () for more details.
The recorder
[1] END SEARCH button (7)
[2] REC indicator (14) -
DISPLAY button (14, 19)
[4] Display window (14, 19)
[5] DC IN 3V jack (at the rear) (6)
[6] MODE button (17)
HE />»I (search / AMS) button (7, 9)
LINE IN (OPTICAL) jack (6, 11)
[9] MIC (PLUG IN POWER) jack (12)
MIC SENS switch (at the bottom) (12)
LINE OUT jack (20)
DIGITAL MEGA BASS button (18)
Ш /СНАЕСЕ button (7, 9, 27)
D> (play) button (7, 9)
Battery compartment (at the rear) (27)
EDIT/ENTER button (21)
AVLS switch (at the bottom) (18)
SYNCHRO REC (synchro-recording)
switch (11)
VOLUME +/- button (9)
T MARK button (21)
21] IE (pause) button (7, 9)
22 REC (record) switch (7)
OPEN button (6)
HOLD switch (20)
25) CLOCK SET button (at the bottom)
(16)
[26] © (headphones) /REMOTE jack (8)
39
40
The display window
[1] Character information display (14, 19)
Displays the disc and track names,
date, error messages, track numbers,
etc.
[2] MONO (monaural) iridication
Play mode indication
Shows the play mode of the MD.
[4] SYNC (synchro-recording) indication
[5] Disc indication
Shows that the disc is rotating for
recording, playing or editing an MD.
[6] REC indication (7)
Lights up while recording. When
flashing, the recorder is in record
standby mode.
AM/PM indication (16)
Lights up along with the time
indication in the 12-hour system.
Mega bass indication (18)
[9] Battery indication (27)
Shows battery condition.
REMAIN (remaining time/ tracks)
indication (14, 19)
Lights up along with the remaining
time of the track, the remaining time
of the MD, or the remaining number
of tracks.
Mi] REC DATE (recorded/ current date)
indication
Lights up along with the date and
time the MD was recorded. When only
“DATE” lights up, the current date
and time are displayed.
12 Time display (14, 19)
Shows the recorded time, current time,
elapsed time of the track or MD being
recorded or played.
Level meter
Shows the volume of the MD being
played of recorded.
The headphones with a remote
control
~
US model
|
N [of [on] >
[1] Headphones
Can be replaced with optional
headphones.
[2] MI (stop) button (7,9)
Control (9)
To play, turn to B»--+ during stop.
Turn to «PP» during play to search
the beginning of the succeeding track;
hold in this position to fast-forward.
Turn to H€< during play to search the
beginning of the preceeding track;
hold in this position to rewind.
HOLD switch (20)
Slide to lock the controls of the remote
control.
I (pause) button (7,9)
other models
[6] PLAY MODE button (17)
[7] DISPLAY button (15, 19)
VOL (volume) +/- buttons (9)
[9] TRACK MARK button (22)
Display window (15, 19)
For customers in the United States
Unfold the supplied headphones as
shown in the illustration below.
TENCE NR
ha BD
a В,
= ul
E ALA
ul
= JL
a UNL MM JE
="
41
Sony Eine http:/www.world.sony.com/
Sony Corporation Printed in Japan
">