USER`S MANUAL
Model No. DTL15141
Serial No.
USER'S MANUAL
Serial Number Decal
QUESTIONS?
If you have questions, or if there
are missing or damaged parts,
we will guarantee complete s a tisfaction through direct assistance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE.
The trained technicians on our
Customer Hot Line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-888-533-1333
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.proform.com
new products, prizes,
fitness tips, and much more!
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING is attached in the center of this manual.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
2. Use the treadmill only as described.
10. When connecting the power cord (see page 8),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 8. To purchase a surge suppressor, see
your local PROFORM dealer or call 1-888-5331333 and order part number 146148.
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
12. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed or stop unexpectedly, which may result
in a fall and serious injury.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should be used only by persons
weighing 300 pounds or less.
13. Keep the power cord and the surge suppressor away from heated surfaces.
8. Never allow more than one person on the
treadmill at a time.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See BEFORE YOU BEGIN on page 4 if the treadmill is
not working properly.)
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
2
15. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
17. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord and move the reset/off circuit
breaker to the off position when the treadmill
is not in use. (See the drawing on page 4 for
the location of the circuit breaker.)
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 5, and HOW TO FOLD
AND MOVE THE TREADMILL on page 21.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
21. When using iFIT.com CDs and videos, you
can manually override the speed setting at
any time by pressing the speed buttons.
However, when the next “chirp” is heard, the
speed will change to the next setting for the
CD or video program.
22. Remove iFIT.com CDs and videos from your
CD player or VCR when you are not using
them.
23. Inspect and properly tighten all parts of the
treadmill regularly.
24. Never insert any object into any opening.
25.
cord immediately after use, before cleaning the
treadmill, and before performing the maintenance and adjustment procedures described in
this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
19. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
20. When using iFIT.com CDs and videos, an
electronic “chirping” sound will alert you
when the speed of the treadmill is about to
change. Always listen for the “chirp” and be
prepared for speed changes. In some instances, the speed may change before the
personal trainer describes the change.
DANGER: Always unplug the power
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.
SAVE THESE INSTRUCTIONS
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
The decals shown have been placed on your treadmill. If a
decal is missing, or if it is not legible, please call our
Customer Service Department, toll-free, to order a free replacement decal (see the front cover of this manual). Apply
the decal in the location shown. Note: The decals are not
shown at actual size.
3
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM®
1200 treadmill. The PROFORM 1200 treadmill combines advanced technology with innovative design to
help you get the most from your exercise program in
the convenience and privacy of your home. And when
you’re not exercising, the unique PROFORM 1200
treadmill can be folded up, requiring less than half the
floor space of other treadmills.
Department toll-free at 1-888-533-1333, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please note
the product model number and serial number before
calling. The model number of the treadmill is
DTL15141. The serial number can be found on a decal
attached to the treadmill (see the front cover of this
manual for the location).
For your benefit, read this manual carefully before
using the treadmill. If you have questions after reading this manual, please call our Customer Service
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
CD Player
Accessory Tray
Fan
Console
Handrail
Storage Latch
Key/Clip
Upright
CD Holder
Reset/Off
Circuit Breaker
Power Cord
Walking Belt
Foot Rail
RIGHT SIDE
Cushioned Walking Platform
for maximum exercise comfort
BACK
Rear Roller
Adjustment Bolts
4
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included allen wrenches
and wire cutters
.
and your own phillips screwdriver
1. Make sure that the power cord is unplugged.
1
To identify small parts, use the PART IDENTIFICATION CHART on page 27.
With the help of a second person, carefully raise the
Upright Base (97) to the position shown. Insert one of
the Extension Legs (92) into the Upright Base. (Note: It
may be helpful to tip the Upright Base forward as you insert the Extension Leg.) Make sure that the Warning
Decal (91) is in the indicated location.
Insert the other Extension Leg (not shown) in the same
way.
91
97
92
2. With the help of a second person, carefully tip the
Upright Base (97) down as shown. (Note: It may be helpful to place your foot on one of the Extension Legs [92]
as you tip the Uprights.) Make sure that the Extension
Legs remain in the Uprights.
2
99
40
Attach each Extension Leg (92) with two Extension Leg
Bolts (96) and two 1/4” Washers (39) as shown. Thread
a Leveling Foot (95) into each side of the Upright Base
(97); do not thread the Leveling Feet fully into the
Upright Base.
99
96
Attach the two Base Pads (99) to the Upright Base (97)
in the locations shown with two 1” Tek Screws (40).
With the help of a second person, raise the Upright Base
(97) to the vertical position.
39
97
39
96
97
92
5
95
40
95
39 96
92
96
3. Attach the Latch Assembly (82) to the Left Upright (84)
with the two Latch Screws (56). Start both Latch Screws
before tightening either of them. Note: The Latch Screws
may be preattached to the Left Upright.
3
82
56
84
4. See step 6 and locate the four Upright Bolts (86). Loosen
the Upright Bolts two to three turns.
See drawing 4c. With the help of a second person, hold
the Console Base (101) near the Uprights (80, 84). Look
under the Console Base and locate the wires on the
sides of the Console Base. Make sure that the wires are
not routed through the openings for the Trays (109,
111). Drawing 4a shows the correct route for the wires;
drawing 4b shows an incorrect route.
4b
4a
Correct
Incorrect
4c
See drawing 4c. Cut the plastic ties holding the Wire
Harness (74) and the pulse wire in the Uprights (80, 84).
Connect the Wire Harness and the pulse wire to the
wires on the sides of the Console Base (101). Make sure
to connect the connectors properly (see the inset
drawings). IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. The connectors should slide together easily and snap into
place. If the connectors do not slide together easily and
snap into place, turn one connector and try again. Insert
the excess Wire Harness and pulse wire up into the
Console Base.
111
101
80
84
74
5. Set the Console Base (101) on the Uprights (80, 84). Be
careful not to pinch the Wires (not shown) in the
Uprights. Attach the Console Base to each Upright with
two Console Bolts (76) and two Internal Star Washers
(77); start all four Console Bolts before tightening any of
them.
109
Pulse
Wire
5
101
84
111
109
Make sure that the Left and Right Trays (109, 111) are
pressed into the Console Base (101).
77
77
76
6
80
76
77
6. Press a CD Holder (85) into each side of the Upright Base
(97).
If the Wheels (not shown) are touching the floor, or if the
treadmill rocks slightly, see HOW TO LEVEL THE
TREADMILL on page 20.
6
84
85
85
97
86
80
If you wish to adjust the height of the Uprights (80,
84), go to step 7. If the Uprights are at the desired
height, tighten the four Upright Bolts (86) and go to step 8.
97
86
7. Note: The Uprights (80, 84) can be attached at three different heights. The Uprights are preattached in the middle position. Adjusting the Uprights requires two persons.
While a second person holds the Console Base (101) and
the Uprights (80, 84), loosen the four Upright Bolts (86).
Then, remove the two Upright Bolts and Upright Star
Washers (127) from the Right Upright (80). Raise or lower
the Right Upright to the desired height, being careful not
to damage the Wire Harness (74). If the Upright Spacer
(79) falls, press it back onto the Upright Base (97).
Loosely thread the two Upright Bolts and Upright Star
Washers back into the Right Upright and the Upright Base.
Adjust the Left Upright (84) in the same way. (Note: There
are no wires in the Left Upright.) Make sure that both
Uprights are at the same height. Lift the Walking
Platform (13) and make sure it is centered between
the Uprights. Retighten all four Upright Bolts (86).
7
84
101
79
127
80
86
13
79
74
97
127
86
8. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included allen wrenches in a secure place. The large allen wrench is used to adjust the
walking belt (see page 23). To protect the floor or carpet, place a mat under the treadmill.
If you purchase the optional chest pulse sensor (see
page 20), follow the steps below to install the receiver
included with the chest pulse sensor.
107
1. Make sure that the power cord is unplugged. Remove
the indicated Screw (108) and the Access Door (122).
2. Remove the paper from the adhesive pad on the back of
the receiver (A). Hold the receiver so the small cylinder is near the lower edge of the receiver and facing
the Console (107) as shown. Firmly press the receiver
onto the indicated corner of the Access Door (122).
Connect the wire on the receiver to the indicated wire extending from the Console.
3. Make sure that no wires are pinched. Reattach the
Access Door (122) with the Screw (108). Note: The wires
included with the receiver may be discarded.
7
Wire
A
Wire
Cylinder
122
108
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking platform. Such substances will deteriorate the walking
belt and cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local PROFORM dealer or call 1-888-533-1333
and order part number 146148.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indicate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpectedly, which may result in a fall and serious injury.
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having
8
Note: If there are thin sheets of clear
plastic on the console, remove them.
Clip
Key
FEATURES OF THE CONSOLE
cline of the treadmill as a personal trainer guides you
through every step of your workout. High-energy music
provides added motivation. To purchase iFIT.com
CDs, call toll-free 1-888-533-1333.
The treadmill console offers an impressive array of
features that help you get the most from your workouts.
When the manual mode of the console is selected, the
speed and incline of the treadmill can be changed with
a touch of a button. As you exercise, the console will
display instant exercise feedback. You can even measure your heart rate using the handgrip pulse sensor or
the optional chest pulse sensor (see page 20).
Using the included audio cable, you can also connect
the treadmill to your VCR and TV and play iFIT.com
video programs. iFIT.com video programs offer the
same benefits as iFIT.com CD programs, and allow
you to enjoy breathtaking scenery while you exercise.
To purchase iFIT.com videocassettes, call toll-free
1-888-533-1333.
In addition, the console offers six preset workout programs. Each program automatically controls the speed
and incline of the treadmill as it guides you through an
effective workout. Two pulse programs are also offered.
Each program automatically adjusts the speed and incline of the treadmill to keep your heart rate within a target range while you exercise.
You can also connect the treadmill to your home computer, go to our Web site at www.iFIT.com, and access
programs directly from our Web site. V i s i t
www.iFIT.com for more information.
To use the manual mode of the console, follow the
steps beginning on page 10. To use preset programs,
see page 12. To use heart rate programs, see page
13. To use iFIT.com CD p r o g r a m s, see page 15. To
use iFIT.com video programs, see page 18. To use
iFIT.com programs directly from our Web site, see
page 19.
The console also features iFIT.com interactive technology. Having iFIT.com technology is like having a personal trainer in your home. Using the built-in CD player,
you can play special iFIT.com CD programs. IFIT.com
CD programs automatically control the speed and in-
9
walking. As you exercise, change the speed of the
walking belt as desired by pressing the Speed ▼
and ▲ b u t t o n s. Each time a button is pressed, the
speed setting will change by 0.1 mph; if a button
is held down, the speed setting will change in increments of 0.5 mph. To change the speed setting
quickly, press the Quick Speed buttons. Note: The
console can display speed and distance in either miles or kilometers. For simplicity, all instructions in this section refer to miles.
HOW TO TURN ON THE POWER
1
Plug in the power cord (see page 8).
2
Locate the reset/off
circuit breaker near
the power cord. Make
sure that the circuit
breaker is in the reset
position.
3
Reset
Position
To stop the walking belt, press the Stop button.
The Time/Pace display will begin to flash. To
restart the walking belt, press the Start button or
the Speed ▲ button.
Stand on the foot rails of the treadmill. Find the clip
attached to the key (see the drawing on page 9)
and slide the clip onto the waistband of your
clothes. Next, route the cord attached to the clip
under the handgrip pulse sensor, and insert the
key into the console. After a moment, the displays
and various indicators will light. Test the clip by
carefully taking a few steps backward until the
key is pulled from the console. If the key is not
pulled from the console, adjust the position of
the clip.
Note: The first time the treadmill is used, observe
the alignment of the walking belt, and align the
walking belt if necessary (see page 23).
4
To change the incline of
the treadmill, press the
Incline ▼ and ▲ b u t t o n s.
Each time a button is
pressed, the incline will
change by 0.5%. T o
change the incline setting quickly, press the Quick
Incline buttons.
HOW TO USE THE MANUAL MODE
1
Insert the key fully into the console.
5
See HOW TO TURN ON THE POWER above.
2
Select the manual mode.
Follow your progress with the matrix and the
displays.
The matrix—When the
manual mode or the
iFIT.com mode is selected, the matrix will
display a 1/4-mile track.
As you exercise, the indicators around the track
will light, one at a time, until the entire track is lit.
The track will then darken and begin to light again.
When the key is inserted, the manual
mode will be selected.
To reselect the manual
mode, press the
Program Select button
repeatedly until a track
appears in the matrix. Make sure that the indicator
on the iFIT.com button is not lit.
3
Change the incline of the treadmill as desired.
Speed display—This
display shows the speed
of the walking belt. Note:
When the KM/H indicator is lit, the console will
display speed and distance in kilometers; when the KM/H indicator is
not lit, the console will display speed and distance
in miles .
Press the Start button or the Speed ▲ button to
start the walking belt.
A moment after the button is pressed, the
walking belt will begin to
move at 1 mph. Hold
the handrails and begin
10
To change the unit of
measurement, first hold
down the Stop button
while inserting the key
into the console. An “E”
for English miles or an
“M” for metric kilometers will appear in the Speed
display. Press the Speed ▲ button to change the
unit of measurement. When the desired unit of
measurement is selected, remove the key.
6
Measure your heart rate if desired.
You can measure your heart rate using either the
handgrip pulse sensor or the optional chest pulse
sensor.
To use the handgrip pulse sensor, first make
sure that your
hands are clean.
Next, stand on
the foot rails
Contacts
and place your
hands on the
metal contacts on the handgrip pulse sensor. Your
palms should be resting on the upper contacts
and your fingers should be touching the lower
contacts. Avoid moving your hands. When your
pulse is detected, two dashes (– –) will appear in
the Calories/Pulse display, and then your heart
rate will be shown. For the most accurate heart
rate reading, continue to hold the contacts for
about 15 seconds.
Calories/Pulse
display—This display
shows the approximate
numbers of calories and
fat calories you have
burned (see FAT BURNING on page 24). The
display will change from one number to the other
every few seconds. The display will also show
your heart rate when you use the handgrip pulse
sensor or the optional chest pulse sensor.
Distance/Incline display—This display
shows the distance that
you have walked or run
and the incline level of
the treadmill. The display
will change from one number to the other every
few seconds. Note: Each time the incline changes,
the display will show the incline setting for several
seconds.
7
Turn on the fan if desired.
To turn on the fan, press the button below the fan.
To turn on the fan at high speed, press the button
a second time. To turn off the fan, press the button a third time. Note: A few minutes after the
walking belt is stopped, the fan will automatically
turn off.
Time/Pace display—
When the manual mode
or the iFIT.com mode is
selected, this display will
show the elapsed time
and your current pace
(pace is measured in minutes per mile). The display will change from one number to the other
every few seconds. When a preset program or a
heart rate program is selected, the display will
show the time remaining in the program rather
than the elapsed time.
8
When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage position or the treadmill will be damaged. Next, remove the key from the console and put it in a secure place. Note: If the displays and various indicators on the console remain lit after the key is
removed, the console is in the “demo” mode.
See page 20 and turn off the demo mode.
To reset the displays, press the Stop button, remove the key, and then reinsert the key.
When you are finished using the treadmill, m o v e
the reset/off circuit breaker switch near the power
cord to the off position and unplug the power cord.
11
The speed setting for the
Current Segment
first segment is shown in
the flashing Current
Segment column of the
matrix. (The incline settings are not shown in
the matrix.) The speed
settings for the next
seven segments are
shown in the seven columns to the right.
HOW TO USE PRESET PROGRAMS
1
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
10.
2
Select one of the preset programs.
When the key
is inserted,
the manual
mode will be
selected. To
select a preset program,
press the Program Select button repeatedly until
one of the six preset program indicators lights.
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. In addition, if the speed
and/or incline of the treadmill is about to change,
the Speed display and/or the Distance/Incline display will flash to alert you. When the first segment
is completed, all speed settings will move one column to the left. The speed setting for the second
segment will then be shown in the flashing Current
Segment column and the treadmill will automatically adjust to the speed and incline settings for
the second segment. Note: If all of the indicators in
the Current Segment column are lit after the speed
settings have moved to the left, the speed settings
will move downward so that only the highest indicators appear in the matrix. If some of the indicators in the Current Segment column are not lit
when the speed settings move to the left again, the
speed settings will move back up.
When a preset program is selected, the Speed
display will flash the maximum speed setting of
the program, and the Distance/Incline display will
flash the maximum incline setting, for six seconds.
The Time/Pace display will show how long the
program will last.
The matrix will show
the first seven speed
settings of the program.
Note: The profiles
below the matrix show
how the speed and incline of the treadmill
will change during the programs.
3
The program will continue in this way until the
speed setting for the last s e g m e n t is shown in the
Current Segment column of the matrix and the
Time/Pace display counts down to zero. The walking belt will then slow to a stop.
Press the Start button or the Speed ▲ button to
start the program.
If the speed or incline setting is too high or too low
at any time during the program, you can manually
override the setting by pressing the Speed or
Incline buttons. Every few times a Speed button is
pressed, an additional indicator will light or darken
in the Current Segment column. (If any of the
columns to the right of the Current Segment column have the same number of lit indicators as the
Current Segment column, an additional indicator
may light or darken in those columns as well.)
Note: When the next segment of the program
begins, the treadmill will automatically adjust
to the speed and incline settings for the next
segment.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into several time segments of different lengths. One speed setting and
one incline setting are programmed for each segment. Note: The same speed setting and/or incline setting may be programmed for consecutive
segments.
12
To stop the program temporarily, press the Stop
button. The Time/Pace display will begin to flash.
To restart the program, press the Start button or
the Speed ▲ button. To end the program, press
the Stop button, remove the key, and then reinsert
the key.
4
HOW TO USE HEART RATE PROGRAMS
CAUTION:
If you have heart problems, or if you are over 60 years of age and
have been inactive, do not use the heart rate
programs. If you are taking medication regularly, consult your physician to find whether the
medication will affect your exercise heart rate.
Follow your progress with the displays.
See step 5 on page 10.
5
Measure your heart rate if desired.
See step 6 on page 11.
6
Turn on the fan if desired.
Follow the steps below to use a heart rate program.
Note: You must wear the optional chest pulse sensor (see page 20) to use a heart rate program.
1
See step 7 on page 11.
7
Put on the chest pulse sensor.
See the instructions included with the optional
chest pulse sensor.
When the program is finished, remove the key
from the console.
2
When the program has ended, make sure that
the incline of the treadmill is at the lowest setting. Next, remove the key from the console and
put it in a safe place. Note: If the displays and
various indicators on the console remain lit
after the key is removed, the console is in the
“demo” mode. See page 20 and turn off the
demo mode.
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
10.
3
Select a heart rate program.
When the key
is inserted, the
manual mode
will be s elected. To select a heart
rate program,
press the Program Select button repeatedly until
one of the two heart rate program indicators lights.
When you are finished using the treadmill, move
the reset/off circuit breaker switch near the power
cord to the off position and unplug the power cord.
The two profiles on the left side of the matrix show
how the target heart rate will change during the
programs. During heart rate program 1, your heart
rate will reach approximately 85% of your estimated maximum heart rate; during heart rate program 2, your heart rate will reach approximately
80% of your estimated maximum heart rate.
Note: Your estimated maximum heart rate is determined by subtracting your age from 220. For
example, if you are 30 years old, your estimated
maximum heart rate is 190 beats per minute
(220 – 30 = 190).
13
4
During heart rate programs, the matrix will
show a graphic that
represents your heart
rate. Each time a heartbeat is detected, an additional peak will appear.
automatically increase or decrease to bring your
heart rate closer to the target heart rate. If the
speed reaches the maximum speed setting of the
program (see step 4 at the left) and your heart
rate is still too far below the current target heart
rate, the incline of the treadmill will also increase
to bring your heart rate closer to the target heart
rate.
Enter your age and a maximum speed setting.
During the last three seconds of each segment, a
series of tones will sound and the Speed display
and the Distance/Incline display will flash.
When a heart rate program is selected, the
word “AGE” and the
current age setting will
flash in the Calories/
Pulse display. If you
have already entered
your age, simply press the Enter Age button. If
you have not entered your age, press the ▲ and ▼
buttons beside the Enter Age button to enter your
age. Then, press the Enter Age button.
The program will continue until no time remains in
the program. The walking belt will then slow to a
stop.
If the speed or incline setting is too high or too low
at any time during the program, you can adjust the
setting with the Speed or Incline buttons. However,
each time the console compares your heart rate to
the current target heart rate, the speed and/or incline of the treadmill may automatically change to
bring your heart rate closer to the target heart
rate.
After you have entered
your age, the letters
“SPd” and the maximum speed setting of
the program will flash in
the Calories/Pulse display. If desired, press
the ▲ and ▼ buttons beside the Enter Age button
to adjust the maximum speed setting. When the
desired setting is shown, press the Enter Age button.
5
If your pulse is not detected during the program,
the letters “PLS” will flash in the Calories/
Pulse display and the speed and incline of the
treadmill may automatically decrease until your
pulse is detected. If this occurs, see the instructions included with the optional chest pulse sensor.
To stop the program at any time, press the St o p
button. Heart rate programs cannot be stopped
temporarily and then restarted. To use a heart rate
program again, reselect the program and start it at
the beginning.
Press the Start button or the Speed ▲ button to
start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
6
Each heart rate program is divided into several time
segments of different lengths. One target heart rate
is programmed for each segment.
7
Follow your progress with the displays.
See step 5 on page 10.
Turn on the fans if desired.
See step 7 on page 11.
During each segment, the console will regularly
compare your heart rate to the current target heart
rate. If your heart rate is too far below or above
the target heart rate, the speed of the treadmill will
8
When the program is finished, remove the key
from the console.
See step 7 on page 13.
14
During the CD program, an electronic “chirping”
sound will alert you when the speed and/or incline
of the treadmill is about to change. CAUTION:
Always listen for the “chirp” and be prepared
for speed and/or incline changes. In some instances, the speed and/or incline may change
before the personal trainer describes the
change.
HOW TO USE IFIT.COM CD PROGRAMS
When you use an iFIT.com CD program, a certified
personal trainer will guide you through your workout as
the program interactively controls the speed and incline of the treadmill. Note: To purchase iFIT.com
CDs, call toll-free 1-888-533-1333.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the CD program.
Follow the steps below to use an iFIT.com CD program.
1
Insert the key into the console.
See HOW TO TURN ON THE POWER on page 10.
2
Select the iFIT.com mode.
To stop the program at
any time, press the Stop
Play/
Pause
button on the console
and then press the
Play/Pause button beside the CD player. The
Time/Pace display will begin to flash. To restart
the program, press the Play/Pause button and
then press the Start button or the Speed ▲ button
on the console. After a moment, the walking belt
will begin to move at 1 mph. When the next
“chirp” is heard, the speed and incline will
change to the next settings of the CD program.
When the key
is inserted,
the manual
mode will be
selected. To
use iFIT.com
CDs, press
the Interactive Trainer button. The iFIT.com indicator will light.
3
Insert an iFIT.com CD into the CD player.
To open the
CD player,
press the lid
of the CD
player in the
indicated location. Carefully
insert an
iFIT.com CD
into the CD
player and close the lid.
4
When the CD program is
completed, the walking
Skip/
Search
belt will slow to a stop
and the Time/Pace display will begin to flash.
Note: To select a different program on the CD, press the Skip/Search
button beside the CD player.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard, make
sure that the iFIT.com indicator is lit and that
the Time/Pace display is not flashing. If the
Time/Pace display is flashing, press the Start
button or the Speed ▲ button on the console.
Press the Play/Pause button to start the
program.
To start the CD program, press the Play/
Play/
Pause button beside
Pause
the CD player. A moment after the button is
pressed, your personal
trainer will begin guiding you through your workout.
Simply follow your personal trainer’s instructions.
Note: If the Time/Pace display is flashing, press
the Start button or the Speed ▲ button on the console. The treadmill will not respond to a CD program while the Time/Pace display is flashing.
5
Adjust the volume if desired.
To adjust the volume,
press the Volume buttons beside the CD
player.
15
Volume
6
HOW TO PLAY MUSIC CDS
Follow your progress with the track and the
displays.
If desired, you can play your own music CDs in the CD
player. Before playing music CDs, select the manual
mode of the console (see HOW TO USE THE MANUAL MODE on page 10). Note: Due to the nature of
CD players, the ability of the player to read a CDRW disk while a user is running vigorously on the
treadmill may be affected by factors such as the
condition of the CD-RW and the quality of the
burner used to create the CD-RW.
See step 5 on page 10.
7
Measure your heart rate if desired.
See step 6 on page 11.
8
Turn on the fans if desired.
See step 7 on page 11.
9
You can also use your own headphones with the CD
player. Headphones with foam ear cushions are recommended to minimize the chances of static electricity
shock. Plug your headphones into the jack below the
fan. Secure the headphone wire to your clothing to
keep the wire out of your way.
When the program is completed, remove the
key.
See step 7 on page 13.
CAUTION: Always remove iFIT.com CDs from
the CD player when you are finished using
them.
16
HOW TO CONNECT THE TREADMILL TO YOUR
COMPUTER
HOW TO CONNECT THE TREADMILL TO
YOUR VCR OR COMPUTER
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
HOW TO CONNECT THE TREADMILL TO YOUR
VCR
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B.
A
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.
LINE OUT
Audio
Cable
LINE OUT
A
ANT
. IN
VIDEO AUDIO
IN
CH
3 4
RF OUT
OUT
AUDIO OUT
RIGHT
A
LEFT
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adapter.
ANT
. IN
VIDEO AUDIO
IN
Audio
Cable
CH
3 4
Adapter
RF OUT
OUT
AUDIO OUT
RIGHT
A
LEFT
PHONES
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the AUDIO OUT
jack on your VCR.
A
B
PHONES
A
ANT
. IN
VIDEO AUDIO
IN
OUT
B
B
Headphones/Speakers
ANT
. IN
VIDEO AUDIO
IN
OUT
RF OUT
CH
3 4
B
RCA Y-adapter
Audio
Cable
3.5mm
Y-adapter
Audio
Cable
RF OUT
CH
3 4
Adapter
B
Wire removed from
AUDIO OUT jack
B
17
heard, the speed and/or incline will change t o
the next settings of the video program.
HOW TO USE IFIT.COM VIDEO PROGRAMS
To stop the walking belt at any time, press the
Stop button on the console. The Time/Pace display will begin to flash. To restart the program,
press the Start button or the Speed ▲ button. After
a moment, the walking belt will begin to move at 1
mph. When the next “chirp” is heard, the
speed and incline will change to the next settings of the video program.
To use iFIT.com videocassettes, the treadmill must be
connected to your VCR. See HOW TO CONNECT
THE TREADMILL TO YOUR VCR on page 17. Note:
To purchase iFIT.com videocassettes, call toll-free
1-888-533-1333.
Follow the steps below to use an iFIT.com video program.
1
When the video program is completed, the walking
belt will stop and the Time/Pace display will begin
to flash. Note: To use another video program,
press the Stop button or remove the key and go to
step 1 on this page.
Insert the key into the console.
See HOW TO TURN ON THE POWER on page 10.
2
Select the iFIT.com mode.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard:
When the key
is inserted,
the manual
mode will be
selected. To
use iFIT.com
videocassettes, press the iFIT.com button. The iFIT.com
indicator will light.
3
• Make sure that the iFIT.com indicator is lit and
that the Time/Pace display is not flashing. If
the Time/Pace display is flashing, press the
Start button or the Speed ▲ button on the
console.
• Adjust the volume of your VCR. If the volume
is too high or too low, the console may not
detect the program signals.
Insert the iFIT.com videocassette.
• Make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord.
Insert the videocassette into your VCR.
4
Press the PLAY button on your VCR.
A moment after the button is pressed, your personal trainer will begin guiding you through your
workout. Simply follow your personal trainer’s
instructions. Note: If the Time/Pace display is
flashing, press the Start button or the Speed ▲
button on the console. The treadmill will not respond to a video program while the Time/Pace
display is flashing.
5
During the video program, an electronic “chirping”
sound will alert you when the speed and/or incline
of the treadmill is about to change. CAUTION:
Always listen for the “chirp” and be prepared
for speed and/or incline changes. In some instances, the speed and/or incline may change
before the personal trainer describes the
change.
7
Follow your progress with the track and the
displays.
See step 5 on page 10.
6
Measure your heart rate if desired.
See step 6 on page 11.
Turn on the fans if desired.
See step 7 on page 11.
8
When the program is completed remove the
key.
See step 7 on page 13.
CAUTION: Always remove iFIT.com videocassettes from your VCR when you are finished
using them.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
18
7
HOW TO USE PROGRAMS DIRECTLY FROM
OUR WEB SITE
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes.
To use programs from our Web site, the treadmill must
be connected to your home computer. See HOW TO
CONNECT THE TREADMILL TO YOUR COMPUTER
on page 17. In addition, you must have an internet
connection and an internet service provider. A list of
specific system requirements are found on our Web
site.
Follow the steps below to use a program from our
Web site.
1
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change t o
the next settings of the program.
Insert the key into the console.
See HOW TO TURN ON THE POWER on page 10.
2
Select the iFIT.com mode.
To stop the walking belt at any time, press the
Stop button on the console. The Time/Pace display will begin to flash. To restart the program,
press the Start button or the Speed ▲ button. After
a moment, the walking belt will begin to move at 1
mph. When the next “chirp” is heard, the speed
and incline will change to the next settings of
the program.
When the key
is inserted, the
manual mode
will be selected. To use
a program
from our Web
site, press the iFIT.com button. The iFIT.com indicator will light.
3
Go to your computer and start an internet
connection.
4
Start your web browser, if necessary, and go to
our Web site at www.iFIT.com.
5
Follow the desired links on our Web site to select a program.
When the program is completed, the walking belt
will stop and the Time/Pace display will begin to
flash. Note: To use another program, press the
Stop button and go to step 5.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard, make
sure that the iFIT.com indicator is lit and that
the Time/Pace display is not flashing. In addition, make sure that the audio cable is properly
connected, that it is fully plugged in, and that it
is not wrapped around a power cord.
Read and follow the on-line instructions for using a
program.
6
Return to the treadmill and stand on the foot
pads. Find the clip attached to the key and slide
the clip onto the waistband of your clothes.
8
Follow the on-line instructions to start the
program.
Follow your progress with the track and the
displays.
See step 5 on page 10.
When you start the program, an on-screen countdown will begin.
9
When the program has ended, remove the key.
See step 7 on page 13.
19
THE INFORMATION MODE/DEMO MODE
HOW TO LEVEL THE TREADMILL
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also allows you to switch the console from miles per hour to
kilometers per hour. In addition, the information mode
allows you to turn on and turn off the demo mode.
If the treadmill wheels
are touching the floor or
if the treadmill rocks
slightly, turn one or both
of the leveling feet
under the upright base
until the wheels are off
the floor and the rocking
motion is eliminated.
Note: If necessary, tip
the treadmill and use a
phillips screwdriver to
turn the leveling feet.
To select the information mode, hold down the Stop
button while inserting the key into the console. When
the information mode is selected, the following information will be shown:
The Distance/Incline display
will show the total number of
miles (or kilometers) that the
walking belt has moved.
Leveling
Feet
Wheel
CHANGING THE ISOLATOR SPRINGS
The treadmill features Isolator Springs (6) that cushion
the walking platform. A pair of Gray Isolator Springs is
preinstalled on the treadmill. For a firmer walking platform, the Gray Isolator Springs can be removed and
the included pair of Blue Isolator Springs can be installed.
The Time/Pace display will
show the total number of
hours the treadmill has been
used.
6
An “E” for English miles or
an “M” for metric kilometers
will appear in the Speed display. Press the Speed ▲ b u tton to change the unit of
measurement.
10
7
12
IMPORTANT: The Calories/Pulse display should be
blank. If a “d” appears in the display, the console is in
the “demo” mode. This mode is intended to be used
only when a treadmill is displayed in a store. When the
console is in the demo mode, the power cord can be
plugged in, the key can be removed from the console,
and the displays and indicators on the console will automatically light in a preset sequence, although the
buttons on the console will not operate. If a “d” appears
in the Calories/Pulse display when the information
mode is selected, press the Speed ▼ button so the
display is blank.
Fold the treadmill to the storage position (see page
21). Using an allen wrench, remove the two Isolator
Bracket Bolts (12) from one of the Isolator Brackets
(10). Remove the Gray Isolator Spring (6) from the
Isolator (7) and slide a Blue Isolator Spring onto the
Isolator. Insert the Isolator back into the circular channel in the Isolator Top Cap (5), and reattach the
Isolator Bracket with the Isolator Bracket Bolts; start
both Isolator Bracket Bolts before tightening either
of them.
To exit the information mode, remove the key.
Replace the other Gray Isolator Spring (6) in the same
way.
THE OPTIONAL CHEST PULSE SENSOR
An optional chest pulse
sensor f e a t u r e s handsfree operation and enables you to use the console’s heart rate programs. To purchase a
chest pulse sensor, call
toll-free 1-888-533-1333.
20
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
1
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be permanently damaged. Next, unplug the power cord. CAUTION:
You must be able to safely lift 45 pounds (20 kg) in order to
raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown at the
right. To decrease the possibility of injury, bend your legs
and keep your back straight. As you raise the treadmill,
make sure to lift with your legs rather than your back.
Raise the treadmill about halfway to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the treadmill until the frame is past
the latch pin. Slowly release the latch knob. Make sure that
the frame is securely held by the latch pin.
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in
temperatures above 85° Fahrenheit.
2
Engaged
Frame
Latch Knob
Latch Pin
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage
position as described above. Make sure that the frame is securely held by the latch pin.
1. Hold the upper ends of the handrails. Place one foot on the
base as shown.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location. To reduce the risk of injury, use extreme caution while moving the treadmill. Do not move the treadmill over an uneven surface.
3. Place one foot on the base, and carefully lower the treadmill
until it is resting in the storage position.
Base
Front Wheels
HOW TO LOWER THE TREADMILL FOR USE
1. See drawing 2 above. Hold the upper end of the treadmill with your right hand. Pull the latch knob to the left
and hold it. Pivot the treadmill down until the frame is past the latch pin.
2. See drawing 1 above. Hold the treadmill firmly with both hands, and lower the treadmill to the floor.
CAUTION: To decrease the possibility of injury, bend your legs and keep your back straight.
21
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department tollfree at 1-888-533-1333, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor
that meets all of the specifications described on page 8. Important: The treadmill is not compatible
with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the reset/off circuit breaker located on the
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.
c
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, please call our Customer Service Department.
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, remove the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM: The console is too high or too low
SOLUTION: a. See assembly step 7 on page 7.
PROBLEM: The treadmill rocks during use
SOLUTION: a. See HOW TO LEVEL THE TREADMILL on page 20.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. With the help of a second person,
carefully tip the Upright Base (97) down as shown.
Remove the five Screws (108). Note: A phillips screwdriver with at least a 5” shaft is required.
a
108
97
22
108
With the help of a second person, carefully raise the
Upright Base (97) as shown. Carefully pivot the Hood
(123) off.
97
123
Locate the Reed Switch (22) and the Magnet (19) on
the left side of the Pulley (18). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8”. If necessary, loosen the Screw
(23) and move the Reed Switch slightly. Retighten the
Screw. Reattach the Hood, and run the treadmill for a
few minutes to check for a correct speed reading.
18
1/8”
22
23
19
Top
View
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 8.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 2 to
3 inches off the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
b
2”–3”
Rear Roller Adjustment Bolts
c. If the walking belt still slows when walked on, please call our Customer Service Department.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the allen wrench to
turn the left rear roller bolt clockwise 1/2 of a turn; if
the walking belt has shifted to the right, turn the
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn both rear roller bolts
clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each side of
the walking belt 2 to 3 inches off the walking platform.
Be careful to keep the walking belt centered. Plug in
the power cord, insert the key, and carefully walk on
the treadmill for a few minutes. Repeat until the walking belt is properly tightened.
23
a
b
CONDITIONING GUIDELINES
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the treadmill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “training zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent postexercise problems.
To measure your heart rate during exercise, use the
pulse sensor. If your heart rate is too high or too low,
adjust the speed and incline of the treadmill.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
24
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
1
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back and
groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles tendons, bend your back leg as well. Stretches: Calves, achilles tendons and ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp one
foot with your other hand. Bring your heel as close to your buttocks
as possible. Hold for 15 counts, then relax. Repeat 3 times for each
leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
25
5
PART LIST—Model No. DTL15141
R0604A
To locate the parts listed below, see the EXPLODED DRAWING attached in the center of this manual.
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
1
12
2
2
2
2
2
2
2
2
4
2
1
2
4
2
2
1
1
8
2
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
10
2
1
2
1
5
1
1
1
1
1
1
Description
Key No. Qty.
Left Foot Rail
Foot Rail Screw
Isolator Bolt (Top)
Isolator Decal
Isolator Top Cap
Gray Isolator Spring
Isolator
Isolator Bottom Cap
Isolator Bracket Cover
Isolator Bracket
Isolator Bracket Bolt
Isolator Bolt
Walking Platform
Belt Guide
Belt Guide Screw
Walking Platform Screw (Rear)
Frame Pivot Bolt
Front Roller/Pulley
Magnet
Pivot Nut
Pivot Spacer
Reed Switch
Reed Switch Screw
Reed Switch Clip
Idler Pivot Bolt
Idler Arm
Pulley/Flywheel/Fan
Motor Pulley
Idler Arm Spring
Idler Arm Washer
Motor
Pulley Nut
Lift Frame
Front Isolator Screw
Walking Platform Nut
Motor Pivot Bolt
Incline Motor
Incline Motor Bolt
1/4” Washer
1” Tek Screw
Front Roller Adj. Bolt
Walking Platform Screw (Front)
Choke
Belly Pan Screw
Hood Cover
Hood Decal
Reset/Off Circuit Breaker
Controller
Power Cord
Power Cord Grommet
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89*
90
91
92
93
94
95
96
97
98
99
100
26
2
10
3
1
1
2
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
2
1
1
4
4
5
2
1
1
1
1
1
2
4
8
2
2
2
2
2
1
2
2
4
1
1
2
2
Description
Static Decal
3/4” Tek Screw
Belly Pan Clip
Belly Pan
Releasable Tie
Latch Screw
Tie Holder Clamp
Cable Tie
Frame
Right Rear Foot
Pulley Washer
Rear Roller Adj, Bolt
Rear Roller
Allen Wrench
5/32” Allen Wrench
Left Rear Foot
Right Foot Rail
Walking Belt
Warning Decal
Photo Switch Wire
Pulse Bar
Filter Wire
Front Isolator
Wire Harness
Right Top Endcap
Console Bolt
Internal Star Washer
Hood Cover Screw
Upright Spacer
Right Upright
Left Top Endcap
Latch Assembly
Controller Wire
Left Upright
CD Holder
Upright Bolt
U-Nut
Upright Endcap (Lower)
Extension Leg Assembly
Wheel Bolt
Warning Decal
Extension Leg
Audio Nut
Wheel
Leveling Foot
Extension Leg Bolt
Upright Base
Photo Switch
Base Pad
Upright Base Endcap
Key No. Qty.
Description
Key No. Qty.
101
1
Console Base
102
1
iFIT.com Wire
103
8
Ground Screw/Choke Screw
104
1
Key Clip
105
1
Optic Disk
106
1
Fan
107
1
Console
108
44
Screw
109
1
Left Tray
110
1
CD Console
111
1
Right Tray
112
1
iFIT.com Wire
3/4” Tek1Screw
113
iFIT.com Jack
(58)–8
114
2
Motor Bracket Bolt
115
1
Photo Switch Screw
116
1
Console Base Frame
117
1
Left Handgrip
118
1
Photo Switch Nut
119
1
Left Bottom Handgrip
120
1
Right Handgrip
121
1
Right Bottom Handgrip
122
123
124
125
126
127
128
129
130
131
132*
133
134
Wheel Nut (13)–2
135*
#
#
#
1
1
1
1
2
4
1
1
1
1
1
2
4
1
1
1
1
Description
Access Door
Hood
Console Back
Photo Switch Star Washer
Rear Roller Star Washer
Upright Star Washer
Controller Bracket
Ground Wire
Idler Pulley
Pulley Bolt
Idler Arm Assembly
Blue Isolator Spring
1” Latch Screw (123)–2
1” Console Bolt
Motor Assembly
6” Blue Wire, 2F
4” Blue Wire, 2F
User’s Manual
*Includes all parts shown in the box
#These parts are not illustrated
PART IDENTIFICATION CHART
Use the drawings below to identify small parts used during assembly. Note: If a part is not in the parts bag,
check to see if it has been preattached to one of the parts to be assembled.
Latch Screw (56)–2
1/4” Washer
(39)–4
Extension Leg Bolt (96)–4
Internal Star
Washer (77)–4
1” Tek Screw (40)–2
Console Bolt (76)–4
27
EXPLODED DRAWING—Model No. DTL15141
R0604A
EXPLODED DRAWING—Model No. DTL15141
R0604A
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-888-533-1333, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). Before calling, please note the following
information:
• The MODEL NUMBER of the product (DTL15141)
• The NAME of the product (PROFORM® 1200 treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the PART LIST on pages 26 and 27 and the
EXPLODED DRAWING attached in the center of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The motor is warranted for three years after the date
of purchase. The belt and deck are covered for two years after the date of purchase. All mechanical
components are covered for two years after the date of purchase. All electrical components are covered
for two years after the date of purchase. Labor is covered for one year. The hood, covers, belly pan, and
decals are covered for six months after the date of purchase.
This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to
replacing or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse,
improper or abnormal usage or repairs not provided by an ICON authorized service center; products
used for commercial or rental purposes; or products used as store display models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 211526 R0604A
Printed in USA © 2004 ICON IP, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement