OWNER’S MANUAL

Safety and Reference

Please read this manual carefully before operating your set and retain it for future reference.

65ART90ESQA www.lg.com

Copyright © 2022 LG Electronics Inc.

All Rights Reserved.

The model and serial number of the product are located on the back and on one side of the product.

Record them below in case you ever need service.

Model

Serial No.

*MFL718258422203REV00*

2

Important Safety Instruction

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Do not use this apparatus near water.

• Clean only with dry cloth.

• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

• Only use attachments/accessories specified by the manufacturer.

• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

• Unplug this apparatus during lightning storms or when unused for long periods of time.

• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Before reading this manual

• Read this manual thoroughly before operating your TV, and keep it for future reference.

• On the website you can download the manual including installation, using, troubleshooting, specifications, license etc and view its contents on your PC or mobile device.

• User Guide : For more information about this TV, read the USER GUIDE embedded in the product. (Depending upon model)

To open the USER GUIDE → → [Support] → [User Guide]

Optional Extras

• Optional extras can be changed or modified for quality improvement without any notification. Contact your dealer for buying these items. These devices work only with certain models.

• The model name or design may be changed due to the manufacturer’s circumstances or policies.

• A cable to connect antennas and external devices must be purchased separately.

Note

• Product specifications or contents of this manual may be changed without prior notice due to upgrade of product functions.

• The items supplied with your product may vary depending upon the model.

• Image shown may differ from your TV.

Warning! Safety instructions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE

PERSONNEL.

The symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the device.

WARNING: TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

• TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER ITEMS WITH

OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.

• Do not place the TV and/or remote control in the following environments:

Keep the product away from direct sunlight.

An area with high humidity such as a bathroom.

Near any heat source such as stoves and other devices that produce heat.

Near kitchen counters or humidifiers where they can easily be exposed to steam or oil.

An area exposed to rain or wind.

Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g., on shelves above the unit).

Near flammable objects such as gasoline or candles, or expose the TV to direct air conditioning.

Do not install in excessively dusty places.

Otherwise, this may result in fire, electric shock, combustion/explosion, malfunction or product deformation.

• Ventilation

Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase.

Do not install the product on a carpet or cushion.

Do not block or cover the product with cloth or other materials while unit is plugged in.

• Take care not to touch the ventilation openings. When watching the TV for a long period, the ventilation openings may become hot.

• Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the device.

• Do not move the TV whilst the Power cord is plugged in.

• Do not use a damaged or loosely fitting power cord.

• Be sure to grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.

• Do not connect too many devices to the same AC power outlet as this could result in fire or electric shock.

• Do not sit on or place objects under the cotton cover. Doing so may cause product damage.

• Disconnecting the Device from the Main Power

The power plug is the disconnecting device. In case of an emergency, the power plug must remain readily accessible.

• Do not let your children climb or cling onto the TV. Otherwise, the TV may fall over, which may cause serious injury.

• Outdoor Antenna Grounding (Can differ by country):

If an outdoor antenna is installed, follow the precautions below.

An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur.

Be sure the antenna system is grounded to provide some protection against voltage surges and built-up static charges.

Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.

Antenna grounding according to the National Electrical Code, ANSI/

NFPA 70

• Never touch this apparatus or antenna during a lightning storm. You may be electrocuted.

• Make sure the power cord is connected securely to the TV and wall socket if not secured damage to the Plug and socket may occur and in extreme cases a fire may break out.

• Do not insert metallic or inflammable objects into the product. If a foreign object is dropped into the product, unplug the power cord and contact the customer service.

• Do not touch the end of the power cord while it is plugged in. You may be electrocuted.

3

4

• If any of the following occur, unplug the product immediately and contact your local customer service.

-

The product has been damaged.

If water or another substance enters the product (like an AC adapter, power cord, or TV).

-

If you smell smoke or other odors coming from the TV

When lightning storms or when unused for long periods of time.

Even the TV is turned off by remote control or button, AC power source is connected to the unit if not unplugged in.

• Do not use high voltage electrical equipment near the TV (e.g., a bug zapper). This may result in product malfunction.

• Do not attempt to modify this product in any way without written authorization from LG Electronics. Accidental fire or electric shock can occur. Contact your local customer service for service or repair.

Unauthorized modification could void the user’s authority to operate this product.

• Use only an authorized attachments / accessories approved by LG

Electronics. Otherwise, this may result in fire, electric shock, malfunction, or product damage.

• Never disassemble the AC adapter or power cord. This may result in fire or electric shock.

• Handle the adapter carefully to avoid dropping or striking it. An impact could damage the adapter.

• To reduce the risk of fire or electrical shock, do not touch the TV with wet hands. If the power cord prongs are wet or covered with dust, dry the power plug completely or wipe dust off.

• Batteries

Store the accessories (battery, etc.) in a safe location out of the reach of children.

Do not short circuit, disassemble, or allow the batteries to overheat.

Do not dispose of batteries in a fire. Batteries should not be exposed to excessive heat.

Caution: Risk of fire or explosion if the battery is replaced by an incorrect type.

• Moving

When moving, make sure the product is turned off, unplugged, and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press or put stress on the front panel of the TV.

Otherwise, this may result in product damage, fire hazard or injury.

• Keep the packing anti-moisture material or vinyl packing out of the reach of children.

• Do not allow an impact shock, any objects to fall into the product, and do not drop anything onto the screen.

• Do not press strongly upon the panel with a hand or a sharp object such as a nail, pencil, or pen, or make a scratch on it. It may cause damage to screen.

• Cleaning

When cleaning, unplug the power cord and wipe gently with a soft/ dry cloth. Do not spray water or other liquids directly on the TV. Do not clean your TV with chemicals including glass cleaner, any type of air freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner, benzene, alcohol etc., which can damage the product and/ or its panel. Otherwise, this may result in electric shock or product damage.

If foreign substances come into contact with the fabric on the front side of the product, wipe them off immediately with a clean wet tissue or cloth. If not cleaned immediately, it may leave a stain.

Due to the nature of the fabric, stains may remain, depending on the type of foreign substance.

Take care as pets or sharp objects may damage the fabric part

Installation

Lifting and moving the TV

Please note the following advice to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size.

• It is recommended to move the TV in the box or packing material that the TV originally came in.

• Before moving or lifting the TV, disconnect the power cord and all cables.

• When holding the TV, the screen should face away from you to avoid damage.

• Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grill area.

• Support the sides of the TV frame, and hold the back center frame firmly.

Make sure not to hold the front cover.

• When transporting a large TV, there should be at least 2 people.

• When transporting the TV, do not expose the TV to jolts or excessive vibration.

• When transporting the TV, keep the TV upright, never turn the TV on its side or tilt towards the left or right.

• Do not apply excessive pressure to cause flexing / bending of frame chassis as it may damage screen.

• When handling the TV, be careful not to damage the protruding buttons.

• Avoid touching the screen at all times, as this may result in damage to the screen.

• When attaching the wall mounting bracket to the TV set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches.

Mounting by fixing to the wall

The TV can be mounted horizontally on the wall, as shown in the figure.

• To install the bracket, make sure the wall is made of material that can withstand the weight of the TV, such as concrete, natural rock, or masonry bricks.

• When installing the TV on other building materials, consult a professional installer before installing.

• When installing the wall fixing bracket, the TV may not be in close contact with the wall, depending on the condition of the wall.

• For cables at the bottom of the set, cable management can be used to organise the cables on both sides, as shown in the example figure.

• For smooth connection with external devices, connect the cable at the rear before fixing the TV to the wall before installing.

• When connecting additional cables, it is recommended to hold the lower center part of the TV and pull it, and then secure enough distance from the wall before connecting.

• When connecting using a bracket for external devices, it is recommended to connect the TV after lowering it from the part where the wall is fixed.

• Leave sufficient space around the product so that the ventilation vents of the TV are not blocked.

• When moving and installing the product, refer to the wall mounting bracket installation dimensions in the assembly manual.

• When packing and moving the product, remove the front cover before packing it.

• Since the center of gravity of the product is at the top, pack the product after turning it upside down so that the center of gravity is at the bottom, and then move it.

• The product can be disassembled by proceeding in the reverse order of assembly. Please refer to the enclosed assembly manual for details.

Provided item

Wall mounting bracket Wall fixing bracket

10 cm

10 cm

Wall fixing bracket fixing screw

Ø 5 x L 65 6 ea

Wall fixing bracket fixing anchor

6 ea

10 cm

For example)

Cable management

Wall mounting bracket fixing screw

Ø 8 x L 15 4 ea

Tools for Installation

• “+” shaped screwdriver (manual or electric) / level / drill / Ø 8 mm drill bit.

Bracket for external device

• It is safe to install the product according to the installation method to prevent the damage to the product or personal injury even if the product is pulled forward.

• When installing, be sure to check the type of wall first, and use the included anchors and screws if it is an installable wall.

If unspecified anchors and screws are used, they may not support the weight of the product and may cause safety problems.

• When drilling holes into the wall, make sure you use a drill and drill bit with the specified diameter. Ensure that you also follow the instructions regarding the depth of the holes.

Otherwise, the product may be installed incorrectly and cause safety issues.

• Be sure to wear work gloves when installing the product.

Installing with unprotected hands may result in injury.

• After mounting on the wall, make sure the bottom of the product touches the floor before use.

If the product is used without touching the floor, it may cause product damage or vibration.

5

6

• Since the TV is heavy, lift it with at least two people when unpacking or moving it.

Do not lay the product down flat; instead, move it in an upright position.

The TV may fall and cause damage or injury.

• Do not move it by holding the cable management and the cable management band.

The cable management and the cable management band may be damaged, and the TV may be damaged or an accident may occur.

(Depending on model.)

• Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and cause it to fall.

• As this is a product for wall-mounted installation only, be sure to install the product on a wall before use.

If you use it without a wall mount, the product may tip over and cause injury.

How to fasten anchors and screws

Wall Material

Concrete

Brick

Natural stone

Metal Panel

Plywood

EPS Panel

Plasterboard + Plywood

Tools

Wall fixing bracket fixing screw, wall fixing bracket fixing anchor, drill bit (Ø 3 / 6 / 8)

Wall mounting bracket fixing screw, drill bit

(Ø 1.8)

Wall Width

70 mm

30 mm

Penetrate the wall

30 mm

• When installing on a gypsum board or medium-density fiberboard

(MDF) wall, fasten the screws to the studs that support the wall. If there are no studs, check the distance from the inner wall before installing.

30 mm or below: Install directly on the inner wall using a 65 mm screw.

30 mm or above: Install using a separate hanger.

Wall fixing bracket fixing anchor

Wall

• When installing the wall mount, check the positions of the wooden studs using a stud finder. Then, fasten the screws on at least two separate studs before proceeding.

Wall fixing bracket fixing screw

1 Drill holes in anchor locations with a drill bit of Ø 8 mm to a depth of

80 mm to 100 mm.

2 Clean the drilled holes.

3 Insert the enclosed wall fixing bracket fixing anchor into the hole.(Use a hammer when inserting anchors.)

4 Attach the wall fixing bracket close to the wall, according to the hole position. At this time, make sure that the “TOP” mark faces upwards.

5 Fit the wall fixing bracket to the hole. At this time, tighten the screws to a torque of between 45 kgf/cm to 60 kgf/cm.

• Check the material of the wall and the thickness of the finishing.

• Use the Wall mount anchor for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry brick and hallow block that do not crack.

Stud Wall fixing bracket

• When installing on other unspecified walls, install it so that it can withstand a pull-out load of 70 kgf (686 N) and a shear load of 100 kgf

(980 N) or more per fixed part.

• Use the Ø 8 mm drill bit for concrete and hammer (Impact) drill.

Antenna/Cable

Connect an antenna, cable, or cable box to watch TV while referring to the following. The illustrations may differ from the actual items and an RF cable is optional.

Copper wire

• Make sure not to bend the copper wire of the RF cable.

• Complete all connections between devices, and then connect the power cord to the power outlet to prevent damage to your TV.

• To improve the picture quality in a poor signal area, purchase a signal amplifier.

• Use a signal splitter to use 2 TVs or more.

• If the antenna is not installed properly, contact your dealer for assistance.

• This TV cannot receive Ultra HD (3840 x 2160 pixels) broadcasts directly because the related standards have not been confirmed (Depending upon country).

Turning on the TV

You can simply operate the TV functions, using the button.

Power On (Press)

Power Off 1) (Press and Hold)

Menu Control (Press 2) )

Menu Selection (Press and Hold 3) )

1) All running apps will close, and any recording in progress will stop.

(Depending on country)

2) You can access and adjust the menu by pressing the button when TV is on.

3) You can use the function when you access menu control.

Note

• If the TV is turned on for the first time after it was shipped from the factory, initialization of the TV may take a few minutes.

• Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.

• The device must be easily accessed to a location outlet near the access.

Some devices are not made by turning on / off button, turning off the device and unplugging the power cord.

Starting TV

Setting the Motion Sensor Time

• The motion sensor works only in Line View mode.

• If no motion is detected around the TV for a set period of time, the screen will turn off automatically.

If no motion is detected for more than a set period of time, the screen will turn off.

To set the power-off time, press the button on the remote control, and then select the set time in → [General] → [System] →

[Additional Settings] → [Screen Off].

If motion is detected even after the screen is turned off, the screen will turn on.

If no motion is detected for more than four hours, the TV will turn off automatically. After that, even if motion is detected, it will not turn on automatically.

Using Line View Mode

• You can check the time and weather information or play music without watching TV.

• You can switch to Full View mode or Line View mode by pressing the

button on the remote control.

• In Line View mode, press the button to switch to Full View mode.

• To completely shut down the TV, press the button on the remote control or press and hold the power button on the back of the product.

Setting the Motion Sensor Sensitivity

Sets the sensitivity of the motion sensor function.

• Press the button on the remote control and refer to →

[General] → [System] → [Additional Settings] → [Motion Sensor

Sensitivity].

Note

• The motion sensor is located at the bottom of the TV screen. Do not cover the front of the sensor with objects, etc. Doing so may affect the motion sensor.

• Sensor performance may vary depending on the TV installation and operating environment.

Screen brightness and color tone may be affected by the color of the floor on which the TV is placed.

In a special light source environment other than standard light sources

(Halogen, Fluorescent), there may be deviations in sensor recognition, depending on the location, type, and number of light sources.

If the surroundings of the TV are too dark or too bright, the screen brightness may be limited or the sensor may not operate properly.

The sensor can detect motion by blinking LEDs, pet dogs, or cars moving outside the window.

• After pressing the button on the remote control, follow →

[General] → [System] → [Additional Settings] → [Screen Off] to turn off the screen and power if there is no user motion in Line View mode.

7

8

Connections

You can connect various external devices to the TV. For more information on external device’s connection, refer to the manual provided with each device.

HDMI

• When connecting the HDMI cable, the product and external devices should be turned off and unplugged.

• Supported HDMI Audio format (Depending upon model):

True HD (48 kHz),

Dolby Digital / Dolby Digital Plus (32 kHz / 44.1 kHz / 48 kHz),

PCM (32 kHz / 44.1 kHz / 48 kHz / 96 kHz / 192 kHz)

Note

• If the device connected to Input Port also supports HDMI Deep Color, your picture may be clearer. However, if the device doesn’t support it, it may not work properly. In that case, change the TV’s [HDMI Deep Color] setting to off.

• → → [General] → [Devices] → [HDMI Settings] → [HDMI

Deep Color]

• Use a certified cable with the HDMI logo attached. If you do not use a certified HDMI cable, the screen may not display or a connection error may occur.

• Recommended HDMI cable types (3 m or less)

Ultra High Speed HDMI ® /™ cable

USB

Some USB Hubs may not work. If a USB device connected through a USB Hub is not detected, connect it directly to the USB port on the TV.

Note

• For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm width.

• Use an extension cable that supports flash drive does not fit into your TV’s USB port.

if the USB cable or USB

IR Blaster

Control the set-top box (cable/satellite/IP/OTT), Blu-ray/DVD player, soundbar, game consoles, etc., using the IR Blaster. (Depending on country)

Note

• Connect the IR Blaster cable to the TV’s IR Blaster port.

• Use universal control settings to control the device.

• Secure the IR Blaster with the 3M tape provided.

IR Repeater

If the set-top box is mounted on the rear bracket, the remote control receiver of the set-top box may be blocked, making it difficult to receive the set-top box remote control. (If this remote control operation problem continues, you can use an IR repeater extender (remote control signal extension cable) to solve the problem.)

1 2

A

B

C

3

Note

• A Receiver: The upper-left corner of the set or a place where remote control reception can be easily received.

Attach with facing forwards.

• B Transmitter: Set-top box receiver.

• C Power Connection: TV or set-top box USB port.

• Integrated remote control setting is required to use the IR repeater. Press the button on the remote control, then select → [General] →

[Devices] → [External Devices] → [Universal Control Settings].

External Devices

Supported external devices are: Blu-ray player, HD receivers, DVD players,

VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices.

Note

• The external device connections shown may differ slightly from illustrations in a manual

• In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the [Picture] menu until the picture is clear. Depending upon the graphics card, some resolution settings may not allow the image to be positioned on the screen properly.

• When connecting to a wired LAN, use a Cat7 cable with high-speed

Internet transmission.

Specifications

Product specifications may be changed without prior notice due to upgrade of product functions.

(Depending upon country)

Television system

Program coverage

Digital

SBTVD (ISDBT)

VHF 2-13

UHF 14-69

DTV 2-69

CATV 1-135

Broadcasting Specifications

Analog Digital

NTSC / PAL-M /

PAL-N

DVB-T / T2

Analog

NTSC / PAL-M /

PAL-N

VHF 2-13

UHF 14-69

DTV 2-69

CATV 1-125

External antenna impedance

75 Ω

Digital

ATSC / 64 &

256 QAM

VHF 2-13

UHF 14-69

DTV 2-69

CATV 1-135

CADTV 1-135

Analog

NTSC-M

Environment Condition

Operating Temperature

Operating Humidity

Storage Temperature

Storage Humidity

0 °C to 40 °C

Less than 80 %

-20 °C to 60 °C

Less than 85 %

• The energy information provided on the product is shown in accordance with the applicable regulations of each respective country, (Depending upon the country).

The Energy consumption was measured in accordance with IEC 62087.

• The actual energy consumption depends on the usage environment, (Example: content watched, TV settings, etc.).

• For information of the power supply and power consumption, refer to the label attached to the product.

The typical power consumption is measured in accordance with IEC 62087 or each country’s energy regulations.

* On some models, the label is inside the external device connection terminal cover.

* Depending upon the model or country, the typical power consumption may not be on label.

9

Product Information

Wireless module (LGSBWAC95) Specifications

Wireless LAN (IEEE 802.11a/b/g/n/ac)

Frequency range

2,400 to 2,483.5 MHz

Output Power (Max.)

18.5 dBm

5,150 to 5,725 MHz

5,725 to 5,850 MHz

18 dBm

18 dBm

Bluetooth

Frequency range

2,400 to 2,483.5 MHz

Output Power (Max.)

9 dBm

As band channels can vary per country, the user cannot change or adjust the operating frequency. This product is configured for the regional frequency table.

For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm between the device and the body.

FCC ID: BEJLGSBWAC95 / IC: 2703H-LGSBWAC95

Open Source Software Notice

Information

To obtain the source code that is contained in this product, under GPL, LGPL,

MPL, and other open source licenses that have the obligation to disclose source code, and to access all referred license terms, copyright notices and other relevant documents please visit  https://opensource.lge.com

.

LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to [email protected].

This offer is valid to anyone in receipt of this information for a period of three years after our last shipment of this product.

Licenses

(Magic Remote supported models only)

10

Troubleshooting

Cannot control the TV with the remote control.

No image display and no sound is produced.

The TV turns off suddenly.

• Check if anything such as tape has been placed over the receiver.

• Check if there is any obstacle between the product and the remote control.

• Replace the batteries with new fresh ones.

• Check if the product is turned on.

• Check if the power cord is connected to a wall outlet.

• Check if there is a problem in the wall outlet by connecting other products.

• Check the power control settings. The power supply may be interrupted.

• Check if the auto-off function is activated in the settings menu.

• If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of inactivity.

Abnormal Display

Generated Sound

The TV stays on or does not turn on automatically in

Line View.

There is lint, thread, or bunching of threads on the front cover.

• If the TV feels cold to the touch, there may be a small flicker when it is turned on. This is normal; there is nothing wrong with TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots.

However, they have no adverse effect on the TV’s performance. Avoid touching the screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

• This panel is an advanced product that contains millions of pixels. In a very few cases, you could see fine dots on the screen while you’re viewing the TV. Those dots are deactivated pixels and do not affect the performance and reliability of the TV.

• Cracking noise A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.

• Electrical circuit humming/panel buzzing A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending upon the product. This generated sound does not affect the performance and reliability of the product.

• The motion sensor is located on the lower center of the TV. If there is any foreign substance on the outside of the sensor, the sensor may not work.

• If the brightness of the TV viewing environment is too bright or too dark, the motion sensor may not operate properly.

• If there are obstacles in front of the TV, the performance of the motion sensor may be affected.

• It can operate by recognising the unintended lighting environment around the TV or the movement of objects

(LEDs/pet dogs/robot vacuum cleaners, etc.).

• The sensor performance can be increased or decreased by adjusting the motion sensor sensitivity in →

→ [General] → [System] → [Additional Settings] → [Motion Sensor Sensitivity].

• In the case of having Kvadrat fabric on the front cover, there may be threads, lint, or bunching of threads due to the nature of the wool material and its natural design. This is an inherent characteristic of natural wool fabrics and is not a product fault. Please note that this is not a valid reason for an exchange or a refund.

• Make sure to wring any excess water or cleaner from the cloth.

• Do not spray water or cleaner directly onto the TV screen.

• Make sure to spray just enough of water or cleaner onto a dry cloth to wipe the screen.

11

12

Precautions for Protecting the OLED TV Screen

Unlike regular LED/LCDs, OLED TVs produce images that emit light for each pixel, achieving a perfect black color and delivering clear images without blurring.

Due to the nature of the organic materials used to achieve high-resolution image quality, OLED displays generally experience image retention on the screen, which can be a persistent phenomenon. This phenomenon is observed in all OLED panels, and although recommended picture modes can Minimize image retention, current technology cannot completely prevent this from occurring.

Displaying the same image for a long time or repeatedly displaying the same image can cause image retention on the screen, which is a common phenomenon in OLED panel products due to the nature of the product. This product has a built-in screen protection feature. Avoid displaying images that are likely to cause image retention, and follow the recommendations.

Running [Pixel Cleaning] to Protect the

OLED TV Screen

The OLED TV is equipped with a pixel cleaning feature to check the status of the screen by itself and prevent image retention that leaves an image on a screen. This feature automatically calculates the optimal execution time based on the accumulated viewing time and is automatically executed when the

TV is turned off. While this feature is running, horizontal lines may appear at the top and bottom of the screen. The pixel cleaning feature works when the product is connected to the power cord and main power.

• To run this function manually, press the button on the remote control, go to → [General] → [OLED Care] → [OLED Panel Care] and press [Pixel Cleaning].

Images that are likely to cause image retention

• Images with black areas on the top and bottom and/or the left and right sides of the screen.

• Images whose aspect ratio is 4:3 or 21:9.

• Images that are fixed for a long time, such as program number, station logo, game console icon, set-top box menu, etc.

• Other fixed screen images or repeatedly displayed images.

Recommendations for Minimizing

Image Retention

When watching the TV for a long time, press the button on the remote control, go to → [Picture] → [Select Mode] and set the mode to [Eco], go to [Advanced Settings] → [Brightness] and set [OLED Pixel Brightness] to a lower level. In addition, press the button on the remote control, go to

→ [General] → [OLED Care] → [OLED Panel Care] and set the [Adjust

Logo Brightness] value to [High].

When showing images with black bars at the top/bottom/left/right side of the screen, press the button on the remote control, press , and go to

[Picture] → [Aspect Ratio] → [User Selection] → [Vertical Zoom] or [4-Way

Zoom] to remove the black bars.

Turn off the menus for setting up devices such as set-top boxes so that they are not displayed on the screen for a long time.

Note

• When the screen is showing one fixed image for a long time, the screen brightness will be automatically reduced and then restored once the screen content changes. This is a normal function to Minimize image retention.

Regulatory

WARNING! (STABILITY HAZARD)

A television set may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such as:

-

ALWAYS use cabinets or stands or mounting methods recommended by the manufacturer of the television set.

ALWAYS use furniture that can safely support the television set.

ALWAYS ensure the television set is not overhanging the edge of the supporting furniture.

ALWAYS educate children about the dangers of climbing on furniture to reach the television set or its controls.

ALWAYS route cords and cables connected to your television so they cannot be tripped over, pulled or grabbed.

NEVER place a television set in an unstable location.

-

NEVER place the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the television set to a suitable support.

NEVER place the television set on cloth or other materials that may be located between the television set and supporting furniture.

NEVER place items that might tempt children to climb, such as toys and remote controls, on the top of the television or furniture on which the television is placed.

If the existing television set is going to be retained and relocated, the same considerations as above should be applied.

The TV should not be placed on tall furniture such as cupboards or bookcases.

Always use the installation method recommended by the TV manufacturer.

Always install the TV on a floor or wall that can safely support it.

If the front cover of the TV moves, be careful as it may cause injury due to jamming.

Always avoid touching the cover when it is moving, and ensure that there are no people or objects around that could get jammed.

Symbols

Refers to alternating current (AC).

Refers to direct current (DC).

Refers to class II equipment.

Refers to stand-by.

Refers to “ON” (power).

Refers to dangerous voltage.

13

14

(Image shown may differ from your TV.)

90 °

, , , , , , , ,

,

, ,

: mm

: kg

Model

65ART90ESQA 1,462 1,568 54.8

223 100 60

Power requirement

20 256 193 1,288 52 0.6

AC 100 - 240 V~ 50/60 Hz

2.0

Power consumption

507 W