-- 4 ROW, 27 FT ALUMINUM BLEACHER --
(STANDARD, PREFERRED & TIP n’ ROLL)
Installation Instructions
BLCH-427
AL → Standard Aluminum 4 Row, 27 Ft Bleacher.
BLDP-427A
L → Preferred Aluminum 4 Row, 27 Ft Bleacher, w/ Double Planks.
BLCH-427
TRG → Standard Aluminum 4 Row, 27 Ft Tip N’ Roll Bleacher.
BLDP-427
TRG → Preferred 4 Row, 27 Ft Tip N’ Roll Bleacher, w/ Double Planks.
Call Jaypro Sports Equipment at 1-800-243-0533 during regular business hours for technical support. www.jaypro.com
REV- 5/19/2011 Page 1 of 6
ITEM PART #
JAYPRO SPORTS
4 ROW, 27 FT ALUMINUM BLEACHER PARTS LIST
DESCRIPTION
5
6
7
8
1
2
3
4
BLAL-4RL 4 ROW LEG FRAME - ALUMINUM
BLALX-77 1/4" x 1 1/4" FLAT X-BARS (BLAL-421RX)
AR5111
AR5044
9 1/2" x 1 1/2" x 27' STADIUM PLANK
5/16" BOLT CLIP
AR5045A
HS5035
HS287
HB5054
9 1/2" SEAT PLANK END CAP
#8 x 1/2" PHILIP SCREW, ZP
3/8"-16 x 1 1/4" HX HD SCREW, ZP
5/16"-18 x 1 1/4" CARRIAGE BOLT, ZP
9 HN5046
10 HN5042
11 CS0011
12 RR5005
13 HN5038
14 HW2050
5/16"-18" FLANGE NUT
3/8"-16 FLANGE NUT, ZP
CASTER WHEEL
RUBBER BUMPER
1/2"-13 FLANGE NUT, ZP
3/8" FLAT WASHER, ZP
Kit #
→
Box #
→
14
70
70
14
N/A
N/A
N/A
14
BLCH-
427AL
5
8
7
70
14
28
BLCH-427K
1
6
25
12
39
39
70
70
39
BLCH-
427TRG
5
8
7
70
14
28
BLTR-427RK
1
BLDP-427K
1
IMPORTANT NOTICE:
1) BEFORE EACH USE CHECK EQUIPMENT FOR PROPER CONNECTING
HARDWARE AND STRUCTURAL INTEGRITY. REPLACE DAMAGED OR
MISSING HARDWARE IMMEDIATELY.
2) USE OF THIS EQUIPMENT OTHER THAN INTENDED, MAY BE
HAZARDOUS.
3) ALTERATION OR MODIFICATION OF THIS EQUIPMENT MAY BE
HAZARDOUS AND RESULT IN INJURY. FOR REPAIR OR
REPLACEMENT, CONTACT YOUR DEALER OR JAYPRO SPORTS.
14
100
100
14
N/A
N/A
N/A
14
BLDP-
427AL
5
8
10
100
20
40
39
100
100
39
6
25
12
39
BLDP-
427TRG
5
8
10
100
20
40
BLDP-427RK
1
REV- 5/19/2011 Page 2 of 6
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED:
(1) 9/16” Socket Wrench and Box Wrench
(1) 3/4” Socket Wrench and Box Wrench
(1) Rubber Mallet
(1) Phillips head screwdriver
•
Unpack all parts and check against parts list to ensure that all have been included.
•
Inspect all parts for damage. Report any damages to the trucking company.
Install Feet and Wheel Casters: (Tip n’ Roll Style Only – if standard bleacher skip to step 3)
1.
Attach five (5) rubber feet (bumpers) on the bottom of each leg as shown in figure 1.
2.
Install two (2) wheel casters on the backside of each frame as shown in figure 2 - fully thread caster stem on, but tighten only finger tight.
Note: The flange of each flange nut should be against the frame member.
REV-
FIGURE: 1 FIGURE: 2
5/19/2011 Page 3 of 6
Assemble Frame:
3.
Assemble undercarriage frame as shown in figure 3. Vertically plumb and square each leg before tightening cross-bracing hardware.
FIGURE: 3
Install Seat and Foot Planks:
4.
Install end caps on both ends of each plank as shown in figure 4 – lightly tap on with a rubber mallet if necessary. Secure end caps in place using the #8 pan head self-drilling screws.
REV-
FIGURE: 4
5/19/2011 Page 4 of 6
5.
Making sure the undercarriage frame is square and plumb, install the seat and foot planks. The seat and foot planks are best installed starting from the front seat and working towards the back. Use the hardware and bolt clip as shown in figure 5. Position planks so they are centered on the frame, with equal amount of overhang on each end. Note that standard bleachers (BLCH-427AL & BLCH-427TRG) have a single foot plank, which is centered on the support frame, see figure 6. Preferred bleachers
(BLDP-427AL & BLDP-427TRG) have double foot planks and are installed as shown in figure 7.
FIGURE: 5
REV-
FIGURE: 6
(SINGLE FOOT PLANK)
5/19/2011 Page 5 of 6
FIGURE: 7
(DOUBLE FOOT PLANK)
Final Adjustments:
•
Checks to make sure the bleacher is properly aligned and square. Securely tightened all plank hardware.
•
For Tip N’ Roll bleachers: using two people stand the bleacher up on the wheel casters. Adjust the wheel height up/down so all the wheels are in equal contact with the floor. Securely tighten both nuts on each wheel caster.
REV- 5/19/2011 Page 6 of 6
