USER MANUAL - Parts Express

USER MANUAL - Parts Express
USER MANUAL
PROFESSIONAL DUAL CD PLAYER
IMPORTANT TO SAFETY
IMPORTANT TO SAFETY
NOTE:
This CD player uses the semiconductor laser. To allow you
to enjoy music at a stable operation, it is recommended to
use this in a room of 5ºC 41ºF - 35ºC 95ºF.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
1. Handle the power supply cord carefully
Do not damage or deform the power supply cord. If it is
damaged or deformed, it may cause electric shock or
malfunction when used. When removing from wall outlet,
be sure to remove by holding the plug attachment and
not by pulling the cord.
RATING LABEL
2. In order to prevent electric shock, do not open the
top cover. If a problem occurs, contact your dealer.
CLASS 1 LABEL
3. Do not place metal objects or spill liquid inside the
CD player. Electric shock or malfunction may result.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR
REFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
Please, record and retain the Model name and serial
number of your set shown on the rating label.
Model No. ___________ Serial No. ___________
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER
(OR BACK) . THERE ARE NO
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
THE COMPACT DISC PLAYER SHOULD NOT BE
ADJUSTED OR REPAIRED BY ANYONE EXCEPT
PROPERLY QUALIFIED SERVICE PERSONNEL.
DOUBLE INSULATED - WHEN SERVICING, USE ONLY
IDENTICAL REPLACEMENT PARTS.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
NOTE:
This unit may cause interference to radio and television
reception.
• Line Voltage Selection (for multiple voltage
model only)
 The desired voltage may be set with the
VOLTAGE SELECTOR switch on the rear
panel, using a screwdriver.
 Do not twist the VOLTAGE SELECTOR
switch with excessive force as this may
cause damage.
 If the VOLTAGE SELECTOR switch does not move
smoothly, please contact a qualified serviceman.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
•FOR U.S.A. & CANADA MODEL ONLY
CAUTION
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS
(POLARIZED) PLUG WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET UNLESS THE
BLADES CAN BE FULLY INSERTED TO PREVENT
BLADE EXPOSURE.
1
SAFETY INSTRUCTIONS
1. Read Instructions – All the safety and operating
instructions should be read before this product is
operated.
2. Retain Instructions - The safety and operating
instructions should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in
the operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions
should be followed.
5. Water and Moisture - The appliance should not be
used near water - for example, near a bathtub,
washbowl, kitchen sink, laundry tub, in a wet basement,
or near a swimming pool, and the like.
6. Carts and Stands - The appliance should be used
only with a cart or stand that is recommended by the
manufacturer.
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces may
cause the appliance and cart combination
to overturn.
7. Wall or Ceiling Mounting - The product should be
mounted to a wall or ceiling only as recommended by
the manufacturer.
8. Heat - The appliance should be situated away from
heat sources such as radiators, heat registers, stoves, or
other appliances (including amplifiers) that produce heat.
9. Power Sources – This product should be operated only
from the type of power source indicated on the rating
label. If you are not sure of the type of power supply to
your home, consult your product dealer or local power
company. For products intended to operate from battery
power, or other sources, refer the operating instructions.
10. Grounding or Polarization – This product may be
equipped with a polarized alternation-current line plug (a
plug having one blade wider than the other). This plug
will fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to
fit, contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the polarized
plug.
11. Power-Cord Protection-Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to the cord in correspondence of
plugs, convenience receptacles, and the point where
they exit from the appliance.
12. Cleaning - The appliance should be cleaned only as
recommended by the manufacturer.
Clean by wiping with a cloth slightly damp with water.
Avoid getting water inside the appliance.
13. For AC line powered units - Before returning repaired
unit to user, use an ohm-meter to measure from both AC
plug blades to all exposed metallic parts. The resistance
should be more than 100,000 ohms.
14. Non-use Periods- The power cord of the appliance
should be unplugged from the outlet when left unused
for a long period of time.
15. Object and Liquid Entry-Care should be taken so that
objects do not fall and liquids are not spilled into the
enclosure through openings.
16. Damage Requiring Service-The appliance should be
serviced by qualified service personnel when:
A. The power-supply cord or the plug has been
damaged; or
B. Objects have fallen, or liquid has been spilled into
the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally
or exhibits a marked change in performance; or
E. The appliance has been dropped, or the enclosure
damaged.
17. Servicing-The user should not attempt any service to
the appliance beyond that described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
18. Ventilation – Slots and openings in the cabinet are
provided for ventilation and to ensure reliable operation
of the product and to protect it from overheating, and
these openings must not be blocked or covered. The
openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in installation
such as a bookcase or rack unless proper ventilation is
the manufacturer’s instructions have been adhered to.
19. Attachments – do not use attachments not
recommended by the product manufacturer as they may
cause hazards.
20. Accessories – Do not place this product on an unstable
cart, stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand,
tripod, bracket, or table recommended by the
manufacturer, or sold with the product. Any mounting of
the product should follow the manufacturer’s instructions,
and should use a mounting accessory recommended by
the manufacturer.
21. Lightning – For added protection for this product during
a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This
will prevent damage to the product due to lightning and
power-line surges.
22. Replacement Parts – When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or have
the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.
23. Safety Check – Upon completion of any service or
repairs to this product, ask the service technician to
perform safety checks to determine that the product is in
proper operating condition.
2
NOTE ON USE
•
•
•
•
•
•
•
•
•
•
Allow for sufficient heat dispersion when installed on a rack.
Handle the power cord carefully.
Hold the plug when unplugging the cord.
Keep the set free from moisture, water, and dust.
Unplug the power cord when not using the set for long periods of time.
Do not obstruct the ventilation holes. (For sets with ventilation holes.)
Do not let foreign objects in the set.
Do not let insecticides, benzene, and thinner come in contact with the set.
Never disassemble or modify the set in any way.
For 220 volt use in USA, USA nema style 220 volt plug. For other countries, use proper plug for the local outlet.
MAIN FEATURES
(1)
(2)
(3)
(4)
(5)
8 times oversampling 1 bit D/A converter.
4 different speed scan.
Frame search.
Auto cue.
Pitch display.
MAIN UNIT
2
3
1
2
6
5
(1)
(2)
(3)
(4)
4
POWER
DISC HOLDER
OP/CL
REMOTE CONTROL CONNECTOR
5
(5) AUDIO OUT L AND R
(6) DIGITAL OUT SOCKET
(7) VOLTAGE SELECTOR (JUST FOR DUAL VOLTAGE
ONLY)
3
MAIN FEATURES
CONTROL UNIT
2 13 16 14 15 8
1
10 11 4 9
5
3
6 7
17
19
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
12
OP/CL
TIME
LCD
REPEAT
PITCH PITCH +
PITCH LOCK
PITCH SLIDER
PLAY/PAUSE
SGL/CTN
(11)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)
18
CUE
+10
PITCH RANGE
CONTROL CONNECTOR
FADER START SOCKETS
LCD
(20)~(23) TRACK,MINUTE,SECOND and FRAME
Displays
(24) BAR Indicators
(25) REMAIN Indicator
(26) TOTAL Indicator
(27) SINGLE Indicator
(28) PITCH DISPLAY
20
21
22 24 23 27 25 26
28
4
PREPARATIONS
1. Checking the Contents
Check that the carton contains the following items:
1) Main unit
2) Control unit
3) Operating instructions (this booklet)
4) Pair of RCA pin cord.
5) Control cords (1 meter)
2. Installing the Unit
Mount the unit onto your console or rack with 19" EIA rack rails.
CAUTION:
The player will work normally when the main unit is
mounted with the front panel at within 15 degrees of the
vertical plane. If the unit is tilted excessively, discs may
not be loaded or unloaded properly.
(Figure 1)
The control panel's LCDs are designed to be
clearly visible within the angles shown in Figure 2.
Mount the control unit so that the visual angle is within
this range.
Max.
15°
45°
5°
Control
panel Button
Main unit
.
Figure 1
Figure 2
Connections
1) Turn off the POWER switch.
2) Connect the RCA pin cord to the input on your mixer.
3) Connect the control cords to the REMOTE connector on the main unit.
CAUTION:
• Be sure to use the supplied control cords. Using another type of cable may result in damage.
• Be sure the power is off when connecting the control cords. Otherwise the units may not work properly.
NAMES AND FUNCTIONS
Main Unit Front Panel
(1) POWER (Power ON/OFF Switch)
When the POWER switch is pressed, the power turns
on.
(2) DISC HOLDER
Place the discs in the holder. Press the OPEN/CLOSE
button to open and close the disc holder.
(3) OP/CL
Press it to open and close the disc holder. The control
unit also includes OPEN/CLOSE button. The disc
holder cannot be opened during playback, so stop
playback before pressing the button.
(4) REMOTE CONTROL CONNECTOR
Connect this connector to the control unit using the
included control cord.
(5) AUDIO OUT
The audio signals from each player are output from
these jacks.
(6) DIGITAL OUT SOCKET
The music-signal of this socket is digital. Connect the
output to the respective input of a digital amplifier for
example.
5
NAMES AND FUNCTIONS
Control Unit
more to resume playback.
(1) OP/CL
Press it to open and close the disc holder. The main unit
also includes OPEN/CLOSE buttons. The disc holder
cannot be opened during playback, so stop playback
before pressing the button.
(2) TIME (Time Button)
Press this button to switch the time display among the
elapsed time and remaining time and total remaining time
of the disc.
(3) LCD
(4) REPEAT
(10)SGL/CTN (Single/Continuous Button)
Press it to switch between the single and continuous
play modes. The SINGLE mode is indicated by the
SINGLE indicator on the LCD
(11)CUE (Cue Button)
Press the CUE button during playback to return to the
position at which playback started.
(12)+10
Use the button to skip ahead 10 tracks.
(13)
When the player is in REPEAT mode and this button is
pushed the song will repeat until the button is pressed
again
Use these button to go back to the beginning of the
current track or select a previous track for playing.
(14),(15)
Press these buttons to perform scan function during
pause mode or during play mode.
(16)
Use these button to skip to the next CD track.
(5) PITCH - BUTTON
The CD slows down while this button is pressed.
Release the button to return to the original BPM.
(6) PITCH + BUTTON
The CD speeds up while this button is pressed.
Release the button to return to the original BPM.
(17)PITCH RANGE
Choose from pitch percentages of 4%,8% and 16%.
(7) PITCH LOCK
(18)CONTROL CONNECTOR
Connect this connector to the REMOTE connector on the
main unit using the included control cord.
(19)FADER START SOCKET
Via the Control socket, the respective CD-player can be
remotely controlled. If you are using a mixer with fader
start-function connect the player with the Control Outsocket. Please note that these sockets must never be
connected with any voltage.
Use these button to enable or disable BPM adjustment
with the pitch sliders. BPM adjustment with the pitch
sliders is enabled when the PITCH LED lights.
(8) PITCH SLIDER
Use the slider to adjust the CD pitch. Slide up to
decrease the pitch, down to increase the pitch.
(9) PLAY/PAUSE
Use the button to start playback. Press once to start
playback, once again to set the pause mode, and once
LCD
TOTAL REMAIN time of playing back
(20)~(23)Track, Minute, Second and Frame Displays
These displays indicate information for the CD’s current
position and time.
(27) CONTINU Indicator
When the indicator lights, the function will cause the unit
to play continuously.
(28) PITCH DISPLAY
It shows the BPM change range, the BPM changes within
a range of +/-16%.
(24)BAR Indicator
These ten indicators provide a visual display of the
approximate position of the pickup within the current track.
(25)REMAIN Indicator
It indicates that the time shown on the display is the
remaining time of playing track
(26)TOTAL Indicator
It indicates that the time shown on the display is the
6
OPERATIONS
1. Opening and Closing the Disc Holder
Turn the unit power on. Press the OPEN/CLOSE button to open the disc holder. OPEN/CLOSE buttons are provided
on both the main unit and control unit.
The disc holder cannot be opened during playback to prevent playback from being interrupted if the OPEN/CLOSE
button is pressed accidentally. Stop the playback first, then press the OPEN/CLOSE button.
2. Loading discs
Hold the disc by the edges and place it in the disc holder, then press the
OPEN/CLOSE button again to close the disc holder. The unit will show the total
track number and the total playing time for about 2 seconds then enter the cue
condition, the cue point will be set to the music starting point of the first track
automatically.
Figure 2-1
CAUTION:
Do not place any foreign objects in the disc holder, and do not place more than one disc in the disc holder at a time.
Do not push the disc holder in manually when the power is off, as this may result in malfunction and damages the player.
3. Selecting Tracks
Press the SKIP button once to move to next higher or lower track.
Hold the SKIP button to change tracks continuously at a higher speed.
When a new track is selected during playback, playback begins as soon as the skip search operation is completed.
If the skip
button is pressed while at the last track, the first track is selected. In the same way, if the skip
button is pressed while at the first track, the last track is selected.
4. Starting Playback
Press the PLAY/PAUSE button during the pause or cue condition to start playback, the PLAY indicator lights.
The point at which playback starts is automatically stored in the memory as the cue point. The pickup then returns to
the cue point when the CUE button is pressed. (Back Cue)
Figure 4-1
5. Stopping Playback
There are two ways to stop playback.
1. Press the PLAY/PAUSE button during playback to pause at that point.
2. Press the CUE button during playback to return to the cue point and enter pause condition.(Back Cue)
CUE
Figure 5
7
OPERATIONS
6. Pausing
˙ Press the PLAY/PAUSE button to switch the play and pause.
˙ The play indicator flashes when the pause mode is set.
˙ Figure 6 show the relationship between the play and pause.
2
4
6
3
7
1
5
Figure 6
The player has completed the cue or pause operation
and is waiting for the play start command.
When the PLAY/PAUSE button is pressed and enter play
mode.
Playing.
The pause mode is set when the PLAY/PAUSE button is
pressed again
Pausing.
Playback resumes when the PLAY/PAUSE button is
pressed again.
Playing.
7. Cueing
˙ "Cueing" is the action of preparing for playback.
˙ Press CUE button, the player will enter cue mode, the playback returns to cue point and enter pause condition, the
cue indicator light up and play indicator flashes. When PLAY/PAUSE button is pressed, play starts from the cue
point.
˙ When the track search operation is completed after pressing the SKIP buttons, the player automatically finds the
position at which the sound starts and cues there(Auto Cue).
˙ If the CUE button is pressed after the search operation or the scanning operation, the playback returns to cue point
and enter pause condition.
˙ Figure 7-1 shows the relationship between the play and back cue operations.
2
8
2
3
1
9
4
6
8
3
7
1
5
9
Figure 7-1
The player has completed the cue or pause operation
pressed again.
and is waiting for the play start command.
Pausing.
When the PLAY/PAUSE button is pressed, playback
When the PLAY/PAUSE button is pressed again;
starts and the cue point is stored in the memory.
Playing.
Playing.
Press the CUE button.
The pause mode is set when the PLAY/PAUSE button is
The pickup returns to the cue point.(Back Cue)
Cue point setting:
When play starts from pause by pressing IN button or Scanning or Frame Search; also skip to a new track by using skip
button, the begin play point will be set to the new cue point.
When a new cue point is set, the cue indicator lights by flash for about 1 second.
NOTE: Daring cue mode, if the CUE button is pressed and hold, playback will start from the cue point, when the button
is released, the player will return to the cue mode automatically, it allows you to check the cue point.
8. JOG WHEEL - The jog wheel serves two functions depending on the current operating mode:
The jog wheel will act as a slow frame search control when the unit is in pause or cue mode allowing you to set a
specific cue point or find a particular starting point.
The inner wheel also works as a momentary pitch bend during playback. Turning the wheel clockwise will increase the
pitch percentage up to 4%,8%,16%, and turning the wheel in the counterclockwise direction will decrease the pitch
percentage up to -16%. The pitch bend will be determined on how fast you turn the wheel.
8
OPERATIONS
9. Scanning (Fast forward/Fast backward)
or
button is pressed.
Scanning is a function for moving quickly forward or backward when the
The scanning speed depends on how long you hold the button.
Press and hold the
or
to begin scanning. The disc moves rapidly forward or backward and the sound is
output. The current scan point is indicated on the LCD.
Press and hold the
to scan in the forward scanning,
to scan in the reverse scanning.
10. Time display
Press TIME button to select time display mode:
Elapsed time of a track.
Remaining time of a track.
ELAPSED
REMAIN
TIME
TIME
Figure 10-1
11. Matching the Beats Per Minute (BPM)
There are two tools available for matching the BPM of the two CDs:
Use the pitch slider to adjust the BPM statically.
Use the PITCH BEND buttons to change the BPM temporarily.
1) Pitch Slider
To adjust the BPM by sliding the pitch slider up or down, press the PITCH button to turn on the PITCH
adjustment function before use.
Slide the pitch slider up to decrease BPM, or down to increase BPM. The adjustment range is +/-10%.
2) Pitch Bending
The BPM increases or decreases respectively while the PITCH BEND+ or PITCH BEND- button is pressed.
The BPM increase depends on how long you hold the button. If you hold the button for about 1/2 second, theBPM will
go either to +16% for PITCH BEND+ or -16% for PITCH BEND-. If you tap the button, the BPM will only change a little
so you can change the beat slightly without audible changes in the music.
The CD will return to the tempo indicated by the Pitch slider when you let go to the PITCH BEND+ or -.
Figure 11-1 shows an example of how to use the pitch bend function. In this example, both players are playing and the
BPM has already been matched with the pitch sliders.
The bass beats also match
CD1
bass beat
Bass beat
PITCH BEND
CD2
bass beat
Bass beat
Figure 11-1
12. Fader start
You have the possibility to start the respective CD-player directly from the mixer. Make sure that the Control socket is
connected with the respective socket on the mixer. Additionally, the Audio out socket have to be connected with the
Line-input sockets of your mixer. Please note that the Fader start function only works with the appropriate mixers. Insert
the CD and select the desired track. Start playback from your mixer.
9
BEFORE SWITCHING OFF THE POWER
When you have finished using the CD player, before switching off the power, be sure that the disc holder had been closed
with the OPEN/CLOSE button.
CAUTION:
Do not forcibly close the disc holder when the power is off.
POWER OFF
POWER OFF
Do not switch off the power when the disc holder is open.
Switch off the power after the disc holder has been closed
with the OPEN/CLOSE button.
COMPACT DISCS
Do not write on the label (printed side) with a hard-tipped
implement such as a pencil or ball point pen.
Condensation will form if a disc is brought into a warm
area from a colder one, such as outdoors in winter. Do
not attempt to dry the disc with a hair dryer, etc.
2. Precaution on storage
After playing a disc, always unload it from the
player.
Always store the disc in the jewel case protect from
dirt or damage.
Do not place discs in the following areas:
Areas exposed to directs sunlight for a considerable time.
Areas subject to accumulation of dust or high humidity.
Areas affected by heat from indoor heaters, etc.
1. Precautions on handling compact discs
Do not allow fingerprints, oil or dust to get on the surface
of the disc.
If the disc is dirty, wipe it off with a soft dry cloth.
Do not use benzene, thinner, water, record spray,
electrostatic-proof chemicals, or silicone-treated cloths to
clean discs.
Always handle discs carefully to prevent damaging the
surface; in particular when removing a disc from its case
or returning it.
Do not bend the disc.
Do not apply heat.
Do not enlarge the hole in the center of the disc.
SPECIFICATIONS
GENERAL
Dimensions:
Main unit:
Control unit:
Weight:
Power supply:
Power consumption:
482(W) x 88.8(H) x 251(D) mm
19”(W) x 3 1/2”(H) x 9 4/5”(D)
482(W) x 88.8(H) x 60(D) mm
19”(W) x 3 1/2”(H) x 2 1/3(D)
5.25 kgs / 11.5 lbs
1.8 kgs / 3.9 lbs
Player unit:
Control unit:
Dual Voltage:
AC 115/230V, 50/60Hz
Single Voltage:
AC 100V, 50/60Hz (For Japan)
AC 110V, 60Hz (For Taiwan)
AC 120V, 60Hz (For U.S.A.,Canada,Mexico)
AC 220V, 50Hz (For United Arab Emirates,Chile,Aegentina)
AC 220V, 60Hz (For Philippines)
AC 230V, 50Hz (For Europe,New Zealand,South Africa,Singapore,Israel)
AC 240V, 50Hz (For Australia,U.K)
15W
10
Stanton Magnetics, Inc. – Warranty Provision – Returns for Repairs or Replacement
WARRANTY
Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the U.S.,
will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the
replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) year following the
date of original purchase. Exceptions to this warranty are as noted below:
The warranty for mechanical parts which are subject to wear and tear are limited to the earlier to occur of thirty (30) days
following the date of original purchase or the following number of cycles: Faders - 15,000; Rotary potentiometers - 10,000; and
Switches - 10,000.
Stanton will warrant all replacement parts and repairs for ninety (90) days from the date of original shipment. Repairs made
necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.
RETURNS
Authorized Stanton dealers are only authorized to sell and distribute merchandise within a specific country. All goods requiring
warranty repair or replacement must be returned (freight prepaid if not hand-delivered) to the authorized Stanton dealer from
whom the merchandise was purchased and in the same country where the merchandise was purchased. For purposes of
purchases made via the Internet, the merchandise must be returned to the authorized Stanton dealer in the country where the
authorized Stanton dealer which sold the merchandise to purchaser is located and not the authorized Stanton dealer in the
country where the purchaser is located or the country in which the merchandise was received. Any returns to a non-authorized
dealer or to an authorized Stanton dealer not in the same country as the merchandise was intended to be sold or as set forth
above will void this warranty.
To initiate a warranty repair, you must contact the authorized Stanton dealer from whom you purchased the merchandise, and
follow such authorized Stanton dealer’s return policy.
Stanton assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application
made of the merchandise. Stanton's liability for any claim, whether based on breach of contract, negligence, infringement of any
rights of any party, or product liability, and relating to the merchandise shall not exceed the price received by Stanton from your
purchase of such merchandise. In no event will Stanton be liable for any special, incidental or consequential damages (including
loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Stanton or otherwise. To the
extent permitted by law and except as otherwise provided above, Stanton disclaims any express or implied warranties of
merchantability or fitness for a particular purpose.
The above warranty provides you with specific legal rights. You may also have additional rights, which are subject to variation
from state to state and country to country.
If there is a dispute regarding the warranty of merchandise that does not fall under the warranty conditions stated above, please
include a written explanation with the merchandise when returned pursuant to the terms and conditions set forth herein.
Please register your product online at www.stantondj.com or mail your completed warranty card to:
Stanton Magnetics, Inc, 3000 SW 42 St. Hollywood, Florida 33312.
cut along dotted line
State
Where did you buy this product?
Date of Purchase
Serial Number
Model Number
PRODUCT INFO
Telephone
Country
City
Address
Name
PERSONAL INFO
Zip
If you have internet access, please register your product at
www.stantondj.com. Otherwise, return this card completely filled
out in order to validate your warranty.
STANTON WARRANTY REGISTRATION CARD
PLACE
STAMP
HERE
Stanton Magnetics, Inc.
3000 SW 42nd Street
Hollywood, FL 33312
U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement