Advertisement
Advertisement
1200Mbps 802.11ac Wave 2 Dual Band
Wireless Access Point w/802.3at PoE+
WDAP-C7210E
WDAP-W1200E
WDAP-850AC
Copyright
Copyright
2020 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, PLANET reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. To assure continued compliance, for example, use only shielded interface cables when connecting to computer or peripheral devices.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undesired operation.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
I
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.
CE Compliance Statement
This device meets the RED 2014/53/EU requirements on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when it is used at a safe distance of 20 cm from your body.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
User Manual of PLANET 802.11ac Dual Band Ceiling-mount Wireless Access Point
Model: WDAP-C7210E/WDAP-W1200E/WDAP-850AC
Rev: 3.0 (Nov., 2021)
Part No. EM-WDAP-C7210E_ WDAP-W1200E_WDAP-850AC _v1.1
I
CONTENTS
1.3
2.1
4.1
5.1
5.2
5.3
5.4
5.5
5.6
5.7
6.1
6.2
6.4
II
III
FIGURE
F IGURE 5-9 S UPER WDS M ODE – 2.4G
IV
V
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Chapter 1. Product Introduction
Package Contents
Thank you for choosing PLANET Wireless AP. Please verify the contents inside the package box.
1.1
Package Contents of WDAP-C7210E
Package Contents of WDAP-W1200E
-1-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Package Contents of WDAP-850AC
If there is any item missing or damaged, please contact the seller immediately.
-2-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Product Description (please refer to PLANET website for WDAP-W1200E
& WDAP-850AC information)
PLANET WDAP-C7210E 1200Mbps Wave 2 Dual Band 802.11ac Wireless AP supports central management through PLANET NMS controllers. With IEEE 802.11ac Wave 2 MU-MIMO 2T2R dual-band technology, the
WDAP-C7210E provides a maximum wireless speed of 867Mbps at 5GHz and 300Mbps at 2.4GHz.
Benefits of MU-MIMO under 802.11ac Wave 2
With the MU-MIMO Wave 2 technology, the WDAP-C7210E, installed in public areas such as hotspots, airports and conferences, reduces the frustration that Wi-Fi users often experience in downloading web pages, e-mail file attachments and media contents. For cellular operators, the WDAP-C7210E provides a better Wi-Fi user experience, reducing the likelihood of users turning off Wi-Fi and putting more load on the cellular network. For enterprises, this technology also can solve Wi-Fi congestion issues in open work spaces and conference rooms.
-3-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Powerful Dual-band WLAN Solution
PLANET WDAP-C7210E, adopting the IEEE 802.11ac Wave 2 standard, provides a high-speed transmission of power and data, meaning two remote nodes in the 5GHz frequency band can be bridged. The 2.4GHz
wireless connection can also be used simultaneously. Furthermore, the WDAP-C7210E adopts the high-class Qualcomm
Atheros SoC (System-on-a-Chip), which provides higher stability to meet the stringent requirements of the solution.
Advanced Security and Rigorous Authentication
The WDAP-C7210E supports 128-bit WEP, WPA / WPA2, WPA-PSK and WPA2-PSK wireless encryptions, the advanced WPA2-AES mechanism and 802.1X RADIUS authentication, which can effectively prevent eavesdropping by unauthorized users or bandwidth occupied by unauthenticated wireless access. Furthermore, any users are granted or denied access to the wireless LAN network based on the ACL (Access Control List) that the administrator pre-established. For management purposes, the IEEE 802.1Q VLAN supported allows multiple VLAN tags to be mapped to multiple SSIDs to distinguish the wireless access.
-4-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Multiple Operation Modes for Various Applications
The WDAP-C7210E supports AP, Gateway, WISP, Repeater and Super WDS modes, through which it provides more flexibility for users when wireless network is established. Compared with general wireless access points, the WDAP-C7210E offers more powerful and flexible capability for wireless clients.
Ceiling-mount Design for Your Environment
With the standard IEEE802.3at Power over Ethernet (PoE) design, the WDAP-C7210E can be easily installed in the areas where power outlets are not available. By supporting the standard IEEE 802.3at PoE PD power scheme, the WDAP-C7210E can be powered and networked by a single UTP cable, effectively eliminating the needs of dedicated electrical outlets on the ceiling and reducing the cabling cost. Furthermore, the system administrator is able to arrange the PoE schedule of the WDAP-C7210E by working with the managed PoE switch.
-5-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Optimized Efficiency in AP Management
The brand-new GUI configuration wizard helps the system administrator easily set up the WDAP-C7210E step by step. Besides, the built-in Wi-Fi analyzer provides real-time channel utilization to prevent channel overlapping to assure greater performance. With the automatic transmission power mechanism, distance control and scheduled reboot setting, the WDAP-C7210E is easy for the administrator to deploy and manage without on-site maintenance. Moreover, you can use PLANET NMS-500 or NMS-1000V AP control function to deliver wireless profiles to multiple APs simultaneously, thus making the central management simple.
-6-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Applications
Extremely High-speed and Dual Band Make Wi-Fi Transmission More Powerful
The WDAP-C7210E delivers the dual band technology to avoid signal interference and ensure the best Wi-Fi performance. It allows you to check e-mails and surf the Internet via the 2.4GHz band and simultaneously watch high-definition (HD) video and any other multimedia application via 5GHz band. Moreover, the Gigabit
Ethernet port of the WDAP-C7210E offers ultra-fast wired connections that utilize the maximum wireless bandwidth; therefore, users will have real wireless speed over 100Mbps. With outstanding stability of high-speed wireless transmission, the WDAP-C7210E can provide users with excellent experience in multimedia streaming with your mobile devices anywhere, anytime.
-7-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
-8-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Product Features (please refer to PLANET website for WDAP-W1200E &
WDAP-850AC information)
Compliant with the IEEE 802.11a/b/g/n/ac wireless technology
Equipped with 10/100/1000Mbps RJ45 ports, auto MDI/MDI-X supported
RF Interface Characteristics
802.11ac Wave 2 2T2R MIMO architecture with data rate of up to 1200Mbps (300Mbps at 2.4GHz and
867Mbps at 5GHz)
High output power with multiply-adjustable transmit power control
Multiple Operation Modes and Wireless Features
Multiple operation modes: AP, Gateway, WISP, Repeater, Super WDS
WMM (Wi-Fi multimedia) provides higher priority to multimedia transmitting over wireless
Coverage threshold to limit the weak signal of clients occupying session
Real-time Wi-Fi channel analysis chart and client limit control for better performance
Support Terminal Fast Roaming with 802.11k, 802.11v, and 802.11r
Secure Network Connection
Full encryption supported: 64-/128-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK and 802.1X RADIUS authentication
Supports 802.1Q VLAN and SSID-to-VLAN mapping
Supports IP/Port/MAC address/URL filtering, DoS, SPI Firewall
Supports DMZ and Port forwarding
Bandwidth control per IP address to increase network stability
Easy Deployment and Management
Supports PLANET AP Controllers in AP mode
Easy discovery by PLANET Smart Discovery
Self-healing mechanism through system auto reboot setting
System status monitoring through remote Syslog Server
Supports PLANET DDNS/ Easy DDNS
-9-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Product Specifications
Product
WDAP-C7210E
1200Mbps 802.11ac Wave 2 Dual Band Ceiling-mount Wireless Access Point
Hardware Specifications
Interfaces
Antennas
LAN
Gain:
2 x 10/100/1000BASE-T RJ45 port
Auto-negotiation and auto MDI/MDI-X
4 x Internal 5dBi antenna (2.4G x2, 5G x2)
Reset button on the rear side (Press over 15 seconds to reset the device to factory
Reset Button
LED Indicators default)
SYS, 2.4G, 5G
Dimensions (W x D x H) 186 x 186 x 35.8mm
Weight 380 ±5g
Power Requirements
Power Consumption
Mounting
48V DC IN, 0.5A, IEEE 802.3at PoE+ or
12V DC IN, 1.5A from DC Jack ( 5.5 x 2.1mm )
< 12W
Ceiling Mount
Wireless Interface Specifications
IEEE 802.11ac
IEEE 802.11n
IEEE 802.11a
IEEE 802.11b
Standard
IEEE 802.11g
IEEE 802.11i
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T
IEEE 802.3x flow control
IEEE 802.11k, 802.11v, and 802.11r
Media Access Control CSMA/CA
802.11ac: OFDM (BPSK / QPSK / 16QAM / 64QAM / 256QAM)
Data Modulation 802.11a/g/n: OFDM (BPSK / QPSK / 16QAM / 64QAM)
802.11b: DSSS (DBPSK / DQPSK / CCK)
Band Mode
Frequency Range
2.4G / 5G concurrent mode
2.4GHz:
FCC: 2.412~2.462GHz
ETSI: 2.412~2.472GHz
5GHz:
FCC: 5.180~5.240GHz, 5.745~5.825GHz
ETSI: 5.180~5.700GHz
FCC: 36, 40, 44, 48, 149, 153, 157, 161, 165 (9 Channels)
ETSI: 36, 40, 44, 48, 100, 104, 108, 112, 116, 132, 136, 140 (12 Channels)
Operating Channels
5GHz channel list may vary in different countries according to their regulations.
Max. Transmit Power FCC: up to 22 ± 1dBm
-10-
(dBm)
Receive Sensitivity
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
ETSI: < 20dBm (EIRP)
Network Mode
2.4GHz
Data Rate
1Mbps
802.11b
11Mbps
6Mbps
802.11g
54Mbps
MCS0/MCS8
802.11n HT20
MCS7/MCS15
MCS0/MCS8
802.11n HT40
MCS7/MCS15
5GHz
802.11a
802.11n HT20
802.11n HT40
802.11ac VHT20
802.11ac VHT40
802.11ac VHT80
6Mbps
54Mbps
MCS0/MCS8
MCS7/MCS15
MCS0/MCS8
MCS7/MCS15
MCS0
MCS8
MCS0
MCS9
MCS0
MCS9
Receive Sensitivity (dBm)
-99
-92
-95
-82
-95
-77
-93
-75
-92
-75
-91
-72
-88
-70
-92
-70
-89
-65
-87
-61
Software Features
LAN
WAN
Wireless Mode
Channel Width
Encryption Security
Wireless Security
Static IP / Dynamic IP
Supports IP-MAC binding
Static IP
Dynamic IP
PPPoE
Access Point
Gateway
WISP
Repeater
Super WDS
20MHz, 40MHz, 80MHz
64-/128-bit WEP, WPA, WPA-PSK, WPA2, WPA2-PSK, 802.1X
Enable/Disable SSID Broadcast
-11-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Wireless max. 32 MAC addresses filtering
Max. SSIDs
Max. Clients
Max. WDS Peers
Wireless QoS
Wireless Advanced
Status Monitoring
User Isolation
4
64 per radio (50 is suggested, depending on usage)
4
Supports Wi-Fi Multimedia (WMM)
Auto Channel Selection
5-level Transmit Power Control (Max.100%, Efficient 75%, Enhanced 50%, Standard
25% or Min. 12.5%)
Client Limit Control, Coverage Threshold
Wi-Fi channel analysis chart
Fast Roaming
Device status, Wireless client List
PLANET Smart Discovery
DHCP client table
System Log supports remote syslog server
VLAN
Self-healing
IEEE 802.1Q VLAN (VID: 3~4094)
SSID-to-VLAN mapping up to 4 SSIDs
Supports auto reboot settings per day/hour
Remote management through PLANET DDNS/ Easy DDNS
Configuration backup and restore
Supports UPnP
Management
Supports IGMP Proxy
Supports PPTP/L2TP/IPSec VPN Pass-through
SNMP v1/v2c/v3 support, MIB I/II, Private MIB
Central Management
[1]
Applicable controllers: NMS-500, NMS-1000V
Remarks [1]: The feature will be supported through firmware/system upgrade.
Environment & Certification
Temperature
Operating: 0 ~ 40 degrees C
Storage: -40 ~ 70 degrees C
Humidity
Operating: 10 ~ 90% (non-condensing)
Storage: 5 ~ 90% (non-condensing)
Regulatory CE, RoHS
-12-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Product
WDAP-W1200E
Dual Band 802.11ac 1200Mbps Wave 2 In-wall Wireless Access Point (EU
Type, 802.3af/at)
Hardware Specifications
Interfaces
Antennas
Button
LED Indicators
Dimensions (W x D x H)
Weight
Power Requirements
Power Consumption
Mounting
Wireless Interface Specifications
LAN
PoE Port
2 x 10/100/1000BASE-T RJ45 port
Auto-negotiation and auto MDI/MDI-X
1 x 10/100/1000Mbps auto MDI/MDI-X RJ45 port (rear panel)
※
IEEE 802.3af/at PD port
RJ11 Port Six-position four-conductor (6P4C) modular jack
Gain 4 x 2dBi antenna
Reset button (Press over 10 seconds to reset the device to the factory default)
LAN1/LAN2/WAN/SYS
86 x 45 x 86 mm
168 ± 5g
48V DC IN, 0.5A, IEEE 802.3af/at PoE+
< 8W
In-wall mount
Standard
Media Access Control
Data Modulation
Band Mode
Frequency Range
Operating Channels
RF Power
Receive Sensitivity
IEEE 802.11ac
IEEE 802.11n
IEEE 802.11a
IEEE 802.11b
IEEE 802.11g
IEEE 802.11i
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3x flow control
CSMA/CA
802.11ac: OFDM (BPSK / QPSK / 16QAM / 64QAM / 256QAM)
802.11a/g/n: OFDM (BPSK / QPSK / 16QAM / 64QAM)
802.11b: DSSS (DBPSK / DQPSK / CCK)
2.4GHz / 5GHz concurrent mode
2.4GHz:
FCC: 2.412~2.462GHz
ETSI: 2.412~2.472GHz
5GHz:
FCC: 5.180~5.240GHz, 5.745~5.825GHz
ETSI: 5.180~5.700GHz
FCC: 36, 40, 44, 48, 149, 153, 157, 161, 165 (9 channels)
ETSI: 36, 40, 44, 48, 100, 104, 108, 112, 116, 132, 136, 140 (12 channels)
5GHz channel list will vary in different countries according to their regulations.
<20dBm (EIRP)
Network Mode
2.4GHz
Data Rate Receive Sensitivity (dBm)
-13-
Software Features
LAN
WAN
Wireless Mode
Channel Width
Encryption Security
Wireless Security
Max. SSIDs
Max. Clients
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
802.11b
802.11g
802.11n
802.11n HT40
1Mbps
11Mbps
6Mbps
54Mbps
MCS0/MCS8
MCS7/MCS15
MCS0/MCS8
MCS7/MCS15
5GHz
802.11a
802.11n HT20
6Mbps
54Mbps
MCS0/MCS8
MCS7/MCS15
802.11n HT40
MCS0/MCS8
MCS7/MCS15
MCS0
802.11ac VHT20
MCS8
802.11ac VHT40
MCS0
MCS9
802.11ac VHT80
MCS0
MCS9
-88
-85
-88
-68
-68
-68
-93
-75
-92
-75
-91
-72
-88
-70
-92
-70
-89
-65
-87
-61
Static IP/DHCP Client
Supports IP-MAC binding
Static IP
Dynamic IP
PPPoE
Access Point
Gateway
WISP
Repeater
Super WDS
20MHz, 40MHz, 80MHz
64-/128-bit WEP, WPA, WPA-PSK, WPA2, WPA2-PSK, 802.1X
Enable/Disable SSID Broadcast
Wireless – filtering of max. 32 MAC addresses
User Isolation
8 ( 4 per radio)
128 (100 is suggested, depending on usage)
-14-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Max. WDS Peers
Wireless QoS
4
Supports Wi-Fi Multimedia (WMM)
Wireless Advanced
Auto channel selection
5-level transmit power control (100%, 75%, 50%, 25%, 12.5%)
Client limit control, coverage threshold
Wi-Fi channel analysis chart
Fast Roaming
Device status, wireless client list
PLANET Smart Discovery
Status Monitoring
VLAN
DHCP client table
System Log supports remote syslog server
IEEE 802.1Q VLAN (VID: 3~4094)
SSID-to-VLAN mapping to up to 4 SSIDs
Self-healing
Supports auto reboot settings per day/hour
Remote management through PLANET DDNS/Easy DDNS
Configuration backup and restoration
Supports UPnP
Management
Supports IGMP Proxy
Supports PPTP/L2TP/IPSec VPN Pass-through
Central Management*
SNMP v1/v2c/v3 support, MIB I/II, Private MIB
Applicable controllers: NMS-500/NMS-1000V, WS-1232P, WS-2864PVR
*Remarks : The feature will be supported through firmware/system upgrade.
Environment & Certification
Temperature
Humidity
Operating: -20 ~ 55 degrees C
Storage: -40 ~ 70 degrees C
Operating: 10 ~ 90% (non-condensing)
Storage: 5 ~ 95% (non-condensing)
CE, RoHS Regulatory
-15-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Product
WDAP-850AC
1200Mbps Dual Band 802.11ac Wave 2 Outdoor Wireless AP
Hardware
Standard Support
IEEE 802.11ac
IEEE 802.11n
IEEE 802.11a
IEEE 802.11b
IEEE 802.11g
IEEE 802.11i
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T
IEEE 802.3x flow control
Material
Dimensions (W x D x H)
Weight
Aluminum
231 x 80 x 295 mm
2.3kg
Power Requirement 48V 0.5A, IEEE 802.3at PoE+
Power Consumption (max.) < 30W
Mounting Type Mast mounting
Interface
Wireless IEEE802.11a/b/g/n/ac, 2T2R
PoE WAN: 1 x 10/100/1000BASE-T, auto-MDI/MDIX, 802.3at PoE In
Button
Antenna
Reset button
Built-in four N-type connectors
Data Rate
Media Access Control
Modulation
Frequency Band
IEEE 802.11b: up to 11Mbps
IEEE 802.11a/g: up to 54Mbps
IEEE 802.11n (20MHz): up to 150Mbps
IEEE 802.11n (40MHz): up to 300Mbps
802.11ac (VHT20): Up to 173.3Mbps
802.11ac (VHT40): Up to 400Mbps
802.11ac (VHT80): Up to 867Mbps
CSMA/CA
802.11ac: OFDM (BPSK/ QPSK/ 16QAM/ 64QAM/ 256QAM)
802.11a/g/n: OFDM (BPSK/ QPSK/ 16QAM/ 64QAM)
802.11b: DSSS (DBPSK/ DQPSK/ CCK)
2.4GHz:
FCC: 2.412~2.462GHz
ETSI: 2.412~2.472GHz
5GHz:
FCC: 5.180~5.240GHz, 5.745~5.825GHz
ETSI: 5.180~5.700GHz
-16-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Operating Channels
2.4GHz:
FCC: 1~11 Channels
ETSI: 1~13 Channels
5GHz:
FCC: 36, 40, 44, 48, 149, 153, 157, 161, 165 (9 Channels)
ETSI: 36, 40, 44, 48, 100, 104, 108, 112, 116, 132, 136, 140 (12 Channels)
5GHz channel list may vary in different countries depending on their regulations.
Max. Transmit Power (dBm)
FCC: up to 29 ± 1dBm
ETSI: < 20dBm (EIRP)
Network Mode
2.4GHz
Data Rate Receive Sensitivity (dBm)
802.11b
802.11g
802.11n HT20
802.11n HT40
1Mbps
11Mbps
6Mbps
54Mbps
MCS0/MCS8
MCS7/MCS15
MCS0/MCS8
MCS7/MCS15
-99
-92
-95
-82
-95
-77
-93
-75
Receiver Sensitivity 5GHz
(dBm)
802.11a
802.11n HT20
802.11n HT40
802.11ac VHT20
802.11ac VHT40
802.11ac VHT80
6Mbps
54Mbps
MCS0/MCS8
MCS7/MCS15
MCS0/MCS8
MCS7/MCS15
MCS0
MCS8
MCS0
MCS9
MCS0
MCS9
-92
-75
-91
-72
-88
-70
-92
-70
-89
-65
-87
-61
Environment & Certification
Operating Temperature -40~70 degrees C
Operating Humidity
IP Level
ESD Protection
Surge Protection
Regulatory
Software
10~90% (non-condensing)
IP67
±8kV air gap discharge
±4kV contact discharge
±20kV
CE, RoHS
-17-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Channel Width
Static IP / DHCP Client
LAN
WAN Type (GW/WISP mode)
Wireless Modes
Supports IP-MAC binding
Static IP
Dynamic IP
PPPoE
Access Point
Gateway
Repeater
Super WDS
WISP
20MHz, 40MHz, 80MHz
Encryption Type 64-/128-bit WEP, WPA, WPA-PSK, WPA2, WPA2-PSK, 802.1X
Enable/Disable SSID Broadcast
Wireless Security Wireless MAC address filtering
User Isolation
Max. SSIDs 8 ( 4 per radio )
Max. Wireless Clients
Max. WDS Peers
Wireless QoS
Wireless Advanced
Status Monitoring
VLAN
Self-healing
Management
Remarks
128 ( 64 per radio )
4
Supports Wi-Fi Multimedia (WMM)
Auto channel selection
5-level transmit power control (100%, 75%, 50%, 25% and 12.5%)
Client limit control, coverage threshold
Distance control (Auto Ack Timeout)
Wi-Fi channel analysis chart
Device status, wireless client List
PLANET Smart Discovery
DHCP client table
System Log supports remote syslog server
IEEE 802.1Q VLAN (VID: 3~4094)
SSID-to-VLAN mapping up to 4 SSIDs
Supports auto reboot settings per day/hour
Supports PLANET Hardware AP Controller controllers
[1]
:WS-1232P/WS-2864PVR/NMS-500/NMS-1000V
Remote management through PLANET DDNS/ Easy DDNS
Configuration backup and restoration
Supports UPnP
Supports IGMP Proxy
Supports PPTP/L2TP/IPSec VPN pass-through
SNMP v1/v2c/v3 support, MIB I/II, Private MIB
1. ^ the feature will be supported through firmware/system upgrade
Applicable
-18-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Chapter 2. Hardware Installation
Product Outlook
WDAP-C7210E
Dimensions:
186 x 186 x 35.8mm
2.1
Weight:
380 ±5g
Triple Viewing
Figure 2-1 WDAP-C7210E Triple Viewing
-19-
Front Panel
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 2-2 WDAP-C7210E Front Panel
LED Definition
LED
PWR
SYS
STATUS
On ( Red )
Off
On
Blinking ( Blue / Green )
FUNCTION
The access point is on.
System is operating.
Wireless LAN is initializing.
2.4GHz/5GHz wireless LAN is working.
-20-
Rear Panel
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Bottom Panel
Figure 2-3 WDAP-C7210E Rear Panel
Figure 2-4 WDAP-C7210E Bottom Panel
Port definition
Object
12V DC
LED
PoE
LAN
Reset
Description
12V DC port for the power adapter( DC-Jack 5.5 x 2.1mm )
The access point is on.
LAN port with Power over Ethernet (PoE) IN
LAN port connecting to the network equipment.
To restore to the factory default setting, press and hold the Reset Button for about 15 seconds, and then release it.
-21-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
WDAP-W1200E
Dimensions(W x D x H):
86 x 45 x 86 mm
Weight:
168 ±5g
Front Panel
Rear Panel
-22-
4-wire RJ11 Connection diagram
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
LED definition
LED
SYS
WAN
LAN 1
STATE
On
Off
Power On
Power Off
FUNCTION
On/Flash WAN connected / data transmitting
Off WAN disconnected
On/Flash LAN 1 connected / data transmitting
Off LAN 1 port disconnected
On/Flash LAN 2 connected / data transmitting
Off LAN 2 port disconnected
LAN 2
Button definition
Object
Reset
Description
Press the Reset button for over 10 seconds and then release it to restore system to the factory default settings.
H/W Interface definition
Object
PoE Port
(802.3af/at PoE+)
LAN 1-2 Port
RJ11 Port
Description
10/100/1000Mbps RJ45 port, auto MDI/ MDI-X
Connect PoE port to the IEEE 802.3af/at PoE+ switch to power on the device.
10/100/1000Mbps RJ-45 port, auto MDI/ MDI-X
Connect this port to the network equipment.
6P4C 4-wire standard
Connect this port to digital phone or traditional phone.
-23-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
WDAP-850AC
Dimensions(W x D x H):
231 x 80 x 295 mm
Weight:
2.3kg ± 0.1kg
Appearance
-24-
Port & Connector
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Hardware Interface Definition
Object
Antenna Connectors
PoE LAN Port
Reset Button
Grounding Terminal
Description
4 N-type (female) antenna connectors
10/100/1000Mbps RJ45 port, auto MDI/MDI-X
802.3at PoE+ supported, 48VDC In
Press and hold the Reset button for over 10 seconds to return to the factory default setting.
The grounding wire must be attached to this port to prevent damage to the AP from direct lightning strike.
-25-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Connecting to the AP
System Requirements
2.2
Broadband Internet Access Service (Cable/xDSL/Ethernet connection)
One IEEE 802.3at PoE switch (supply power to the WDAP Series)
PCs with a working Ethernet adapter and an Ethernet cable with RJ45 connectors
PCs running Windows 98/ME, NT4.0, 2000/XP, Windows Vista / Win 7, MAC OS 9 or later, Linux,
UNIX or other platforms compatible with TCP/IP protocols
1. The AP in the following instructions refers to PLANET WDAP-C7210E. (Please refer to
WDAP-W1200E/WDAP-850AC QIG to install the AP)
2. It is recommended to use Internet Explorer 11, Firefox or Chrome to access the AP.
2.3
Installing the AP
Before installing the AP, make sure your PoE switch is connected to the Internet through the broadband service successfully at this moment. If there is any problem, please contact your local ISP.
Please install the AP according to the following steps. Don't forget to pull out the power plug and keep your hands dry.
Step 1. Take the mounting bracket, put it on the target place by aligning the holes and fix it with the supplied screws.
Figure 3-1 Mounting the Bracket
-26-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Step 2. Load the device into the mounting bracket, and be sure the device is mated with fixed screws. Then, lock the device in position and plug the Ethernet cable into the WDAP-C7210E.
Figure 3-2 Connecting the Ethernet Cable
Step 3. Plug the other end of the Ethernet cable into the PoE switch.
Figure 3-3 Connecting the PoE Injector
-27-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Chapter 3. Quick Installation Guide
This chapter will show you how to configure the basic functions of your AP within minutes.
A computer with wired Ethernet connection to the Wireless AP is required for the first-time configuration.
Manual Network Setup -- TCP/IP Configuration
3.1
192.168.1.253
. And the default subnet mask is 255.255.255.0.
These values can be changed as you want. In this guide, we use all the default values for description.
Connect the WDAP series with your PC by plugging one end of an Ethernet cable in the LAN port of the AP and the other end in the LAN port of PC. The WDAP series is powered by a PoE switch.
In the following sections, we’ll introduce how to install and configure the TCP/IP correctly in Windows 10 . And the procedures in other operating systems are similar. First, make sure your Ethernet Adapter is working, and refer to the Ethernet adapter manual if needed.
3.1.1 Configuring the IP Address Manually
Summary:
Set up the TCP/IP Protocol for your PC.
Configure the network parameters. The IP address is 192.168.1.xxx (If the default IP address of the
WDAP series is 192.168.1.253, and the DSL router is 192.168.1.254, the "xxx" can be configured to any number from 1 to 252.) and subnet mask is 255.255.255.0.
1 Select Use the following IP address , and then configure the IP address of the PC.
2 For example, the default IP address of the WDAP series is 192.168.1.253 and the DSL router is
192.168.1.254, or you may choose from 192.168.1.1 to 192.168.1.252.
-28-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 4-1 TCP/IP Setting
Now click OK to save your settings.
Now, you can run the ping command in the command prompt to verify the network connection between your
PC and the AP. The following example is in Windows 10 OS. Please follow the steps below:
1. Click on Start > Run .
2. Type “ cmd ” in the Search box.
-29-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 4-2 Windows Start Menu
3. Open a command prompt, type ping 192.168.1.253
and then press Enter .
If the result displayed is similar to Figure 4-3 , it means the connection between your PC and the AP has been established well.
Figure 4-3 Successful Result of Ping Command
-30-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
If the result displayed is similar to Figure 4-4 , it means the connection between your PC and the AP has failed.
Figure 4-4 Failed Result of Ping Command
If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your AP. Some firewall software programs may block a DHCP request on newly installed adapters.
-31-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Starting Setup in the Web UI
It is easy to configure and manage the AP with the web browser.
3.2
To access the configuration utility, open a web-browser and enter the default IP address http://192.168.1.253
in the web address field of the browser.
Figure 4-5 Login by Default IP Address
After a moment, a login window will appear. Enter admin for the password in lower case letters. Then click
LOGIN or press the Enter key.
Figure 4-6 Login Window
Default IP Address: 192.168.1.253
Default Password: admin
If the above screen does not pop up, it may mean that your web browser has been set to a proxy. Go to Tools menu> Internet Options> Connections> LAN Settings on the screen that appears, uncheck Using Proxy and click OK to finish it.
-32-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Chapter 4. Configuring the AP
This chapter delivers a detailed presentation of AP’s functionalities and features 3 main items below, allowing you to manage the AP with ease. (The below web GUI and topology uses WDAP-C7210E as an example)
Figure 5-1 Main Menu
The page includes the following fields:
Object
Operation Mode
Description
It shows the current mode status.
Device Information
It shows the CPU/memory usage.
Device Description
You can enter the device description.
Flow (5G Wi-Fi) bps
It shows the Upstream/Downstream graph.
LAN Information
Wi-Fi Information
Version
It shows the device IP mode, LAN IP, subnet, gateway and MAC address.
It shows the Wi-Fi status, SSID, channel, Encryption, MAC address and client list.
It shows the firmware version (Double-click to show more detailed info.).
-33-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Wizard
The Wizard guides you to configuring the WDAP Series in a different mode, including Gateway, Super WDS,
WISP, Repeater, AP modes.
4.1
Figure 5-2 Operation Mode
The default operation mode is AP Mode.
-34-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Gateway Mode (Router)
Click “ Wizard ” “ Gateway Mode ” and the following page will be displayed. This section allows you to configure the Gateway mode.
4.2
Figure 5-3 Gateway Mode
-35-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
4.2.1 WAN Settings
Static IP
If your ISP offers you static IP Internet connection type, select “ Static IP " and then enter IP address, subnet mask, default gateway and primary DNS information provided by your ISP in the corresponding fields.
Figure 5-4 Gateway -Static IP
The page includes the following fields:
Object
IP Address
Description
Enter the WAN IP address provided by your ISP. Enquire your ISP if you are not clear
Subnet Mask
Enter WAN Subnet Mask provided by your ISP
Default Gateway
Enter the WAN Gateway address provided by your ISP
Primary DNS
Enter the necessary DNS address provided by your ISP
Second DNS
Enter the second DNS address provided by your ISP
PPPoE (ADSL)
Select PPPOE if your ISP is using a PPPoE connection and provide you with PPPoE user name and password info.
-36-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-5 Gateway – PPPoE (ADSL)
The page includes the following fields:
Object
Username
Password
Server Name
Service Name
Description
Enter the PPPoE User Name provided by your ISP
Enter the PPPoE password provided by your ISP
Enter the server name by your ISP, or not
Enter the service name by your ISP, or not
-37-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
DHCP
Choose “ DHCP ” and the router will automatically obtain IP addresses, subnet masks and gateway addresses from your ISP.
4.2.2 Wireless
Figure 5-6 Gateway – DHCP
-38-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-7 Gateway – Wireless
The page includes the following fields:
Object
Wi-Fi Status
SSID
Hide your SSID
Channel
Encryption
Timing
Description
Select ON ( Green ) or OFF ( Gray ) to enable or disable wireless LAN
It is the wireless network name. The default SSID is PLANET_2.4G and PLANET_5G
Select ON ( Green ) or OFF ( Gray ) to hide wireless LAN or not
Select the operating channel you would like to use. The channel range will be changed by selecting a different domain.
Select the wireless encryption. The default is None
Set time to restart for clock
-39-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Super WDS Mode
In the Super WDS mode, the wireless interface can be connected with other wireless APs through WDS, and the wireless interface and cable interface. Click “ Wizard ” “ Super WDS Mode ” and the following page will be
WDS mode before scanning wireless.
Figure 5-8 Super WDS Mode
-40-
The page includes the following fields:
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Object
Select Network
WDS SSID
Description
Select network for using 2.4G
or 5G to do connection.
It is the WDS wireless network name. The default SSID is
“ Wireless2.4G_WDS
” or “ Wireless5.8G_WDS
”.
AP BSSID/Mark
Encrypt
Press the “ Scan ” button to find the WDS BSSID to connect.
Select open or WEP for the wireless encryption. The default is None.
Key in the correct password for BSSID of WEP.
In this step you can set up the 2.4G and 5G wireless of AP SSID.
Figure 5-9 Super WDS Mode – 2.4G SSID
-41-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-10 Super WDS Mode – 5G SSID
The page includes the following fields:
Object
Wi-Fi Status
SSID
Hide your SSID
Bandwidth
Channel
Encrypt
Description
Select ON ( Green ) or OFF ( Gray ) to enable or disable wireless LAN
It is the wireless network name. The default SSID is “ PLANET_5G ”
Select ON ( Green ) or OFF ( Gray ) to hide wireless LAN or not
Select the operating channel width, “ 20MHz ” or “ 40MHz ” or
“ 80MHz ”
Select the operating channel you would like to use. The channel range will be changed by selecting a different domain.
Select the wireless encryption. The default is “ None ”
-42-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
The page includes the following fields:
Figure 5-17 Super WDS Mode
Object
IP Mode
Timing
Description
Select “ Static IP ” or “ DHCP Client ” for setting up device IP
Set time to restart
Connection section for example,
AP1 – Enter the WDS SSID and encrypt password.
-43-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-18 Super WDS Mode – AP1
AP2 -- Press the “ Scan ” button to find AP1 BSSID and choose it to connect. Enter the encrypt password.
Figure 5-19 Super WDS Mode – AP2
-44-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
WISP Mode
Click “ Wizard ” “ WISP Mode ” and the following page will be displayed. This section allows you to configure the WISP mode.
4.4
-45-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-20 WISP Mode
The page includes the following fields:
Object
Bandwidth
Description
Select network for using 2.4G
or 5G to do connection.
Repeater SSID
Lock BSSID
Encryption
Password
Bandwidth
Enter the root AP’s SSID or press “ Scan ” to select.
Check to lock the root AP’s MAC address.
Select the wireless encryption of root AP. The default is
“ WPA/WPA2PSK_TKIPAES ”.
Enter the password of root AP.
Select the operating channel width, “ 20MHz ” or “ 40MHz ” or “ 80MHz ”.
-46-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-21 WISP Mode – Select Internet Mode (Set up WAN type)
-47-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-22 WISP Mode – Setting up Wi-Fi
-48-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Repeater Mode (Universal Repeater)
Click “ Wizard ” “ Repeater Mode ” and the following page will be displayed. This section allows you to configure the Repeater mode.
4.5
-49-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-23 Repeater Mode
The page includes the following fields:
Object
Select Network
Description
Select “ 2.4G
” or “ 5.8G
” wireless LAN.
Repeater SSID Enter the root AP’s SSID or press “ Scan ” to select.
Lock BSSID
Encryption
Password
Bandwidth
P2P
Check to lock the root AP’s MAC address.
Select the wireless encryption of root AP. The default is
“ WPA/WPA2PSK_TKIPAES ”.
Enter the password of root AP.
Select the operating channel width, “ 20MHz ” or “ 40MHz ” or “ 80MHz ”.
Enable switch for Point to Point function.
Press Scan to show the root AP that you need to repeat and press Choice to select the AP.
-50-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-24 Repeater Mode -- Scan Root AP
-51-
Set up the repeater wireless network
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-25 Repeater Mode – Setting up Wi-Fi
-52-
The page includes the following fields:
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Object
Wi-Fi Status
SSID
Hide your SSID
Encryption
Timing
Description
Select ON ( Green ) or OFF ( Gray ) to enable or disable wireless LAN.
It is the wireless network name. The default SSID is “ PLANET_5G
Select ON ( Green ) or OFF ( Gray ) to hide wireless LAN or not.
Select the wireless encryption. The default is “ None ”.
Set time to restart.
”.
Figure 5-26 Repeater Mode – Setting up device IP
-53-
The page includes the following fields:
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Object
IP Mode
LAN IP
Subnet
Gateway
Primary DNS
Secondary DNS
Description
Select “ Static IP ” or “ DHCP Client ” for setting up device IP.
Enter the AP static IP address.
Enter the network mask.
Enter the default gateway IP address.
Enter the primary DNS IP address, or not.
Enter the secondary DNS IP address, or not.
Enter the LAN IP address.
-54-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
AP Mode
In the AP mode, the AP wireless interface and cable interface bridge together. Click “ Wizard ” “ AP Mode ” and the following page will be displayed. This section allows you to configure the AP mode.
4.6
Figure 5-27 AP Mode
-55-
The page includes the following fields:
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Object
IP Mode
LAN IP
Subnet
Gateway
Primary DNS
Secondary DNS
Description
Select “ Static IP ” or “ DHCP Client ” for setting up device IP.
Enter the AP static IP address.
Enter the network mask.
Enter the default gateway IP address.
Enter the primary DNS IP address, or not.
Enter the secondary DNS IP address, or not.
Enter the LAN IP address.
-56-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-28 AP Mode – Set up Wi-Fi
The page includes the following fields:
Object
Wi-Fi Status
SSID
Hide your SSID
Bandwidth
Channel
Encryption
Timing
？
Description
Select ON ( Green ) or OFF ( Gray ) to enable or disable wireless LAN.
It is the wireless network name. The default SSID is “ PLANET_5G ”.
Select ON ( Green ) or OFF ( Gray ) to hide wireless LAN or not.
Select the operating channel width, “ 20MHz ” or “ 40MHz ” or
“ 80MHz ”.
Select the operating channel you would like to use. The channel range will be changed by selecting a different domain.
Select the wireless encryption. The default is “ None ”.
Set time to restart.
-57-
Wi-Fi
4.7.1 2.4G/5G Wi-Fi
4.7.1.1. Basic
4.7
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-29 Basic
-58-
The page includes the following fields:
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Object
Wi-Fi Status
SSID
Hide your SSID
Channel
Encryption
WMM
Wi-Fi Analyzer
？
Description
Select ON ( Green ) or OFF ( Gray ) to enable or disable wireless LAN.
It is the wireless network name. The default SSID is “ PLANET_2.4G
” or “ PLANET_5G ”.
Select ON ( Green ) or OFF ( Gray ) to hide wireless LAN or not.
It shows the channel of the CPE. Default 2.4GHz is channel 6.and
5GHz is channel 36.
Select the wireless encryption. The default is “ None ”.
Enable/Disable WMM ( Wi-Fi Multimedia ) function.
Press this button to analyze local area wireless signal.
4.7.1.2. VAP
Figure 5-30 VAP
Select VAP1~VAP3 to enable virtual AP.
The page includes the following fields:
Object
Wi-Fi Status
SSID
Hide your SSID
Channel
Encryption
WMM
Description
Select ON ( Green ) or OFF ( Gray ) to enable or disable virtual wireless
LAN.
It is the wireless network name. The default 2.4G SSID is
“ PLANET_2.4G_1
” to “ PLANET_2.4G_3
” and 5G SSID is
“ PLANET_5G_1 ” to “ PLANET_5G_3 ”.
Select ON ( Green ) or OFF ( Gray ) to hide wireless LAN or not.
It shows the channel of the CPE. Default 2.4GHz is channel 6.and
5GHz is channel 36.
Select the wireless encryption. The default is “ None ”.
Enable/Disable WMM (Wi-Fi Multimedia ) function.
-59-
4.7.2 MAC ACL
4.7.2.1. MAC ACL
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-11 MAC ACL
The page includes the following fields:
Object
Add
Delete
Apply
ACL Status
Description
Press the “ Add ” button to add end-device that is scanned from wireless network and mark them.
Press the “ Delete ” button to delete device from list.
Press the “ Apply ” button to enable/disable the rule.
Select the rule of ACL, default is Disable .
Whitelist: Allows the devices to pass in the rule
Blacklist: Prohibited rules within the device through
Figure 5-32 ACL status
-60-
4.7.3 Wi-Fi Timer Off
4.7.3.1. Wi-Fi Timer Off
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-33 Wi-Fi Timer Off
The page includes the following fields:
Object
Wi-Fi Timer Off
Time Frame
Description
Select ON ( Green ) or OFF ( Gray ) to enable or disable timer.
Choose the time frame of Wi-Fi.
-61-
4.7.4 Advanced
4.7.4.1. Advanced
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-34 Advanced
The page includes the following fields:
Object Description
2.4G Mode
5G Mode
Maximum 2.4G per AP
Maximum 5G per AP
2.4G WLAN Partition
5G WLAN Partition
Select 802.11B/G or 802.11N/G in CPE.
Select 802.11A
or 802.11AN
or 802.11AC
in CPE.
The maximum users are 64.
The maximum users are 64.
Enable it to isolate each connected wireless client so that they cannot access mutually.
Enable it to isolate each connected wireless client so that they cannot access mutually.
2.4G Coverage Threshold The coverage threshold is to limit the weak signal of clients occupying session. The default is -90dBm.
5G Coverage Threshold The coverage threshold is to limit the weak signal of clients occupying session. The default is -90dBm.
2.4G TX Power The range of transmit power is Max (100%) , Efficient (75%) ,
Enhanced (50%), Standard (25%) or Min (12.5%) . In case of shortening the distance and the coverage of the wireless network, input a smaller value to reduce the radio transmission power.
-62-
5G TX Power
Multicast Fast
Short GI
Packet Threshold
RTS Threshold
Preferred 5G
Terminal Fast Roam
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
The range of transmit power is Max (100%) , Efficient (75%) ,
Enhanced (50%), Standard (25%) or Min (12.5%) . In case of shortening the distance and the coverage of the wireless network, input a smaller value to reduce the radio transmission power.
A part of the 802.11n standard that allows sending multiple frames per single access to the medium by combining frames together into one larger frame. It creates the larger frame by combining smaller frames with the same physical source, destination end points, and traffic class
(QoS) into one large frame with a common MAC header.
Guard intervals are used to ensure that distinct transmissions do not interfere with one another.
When the length of a data packet exceeds this value, the router will send an RTS frame to the destination wireless node, and the latter will reply with a CTS frame, and thus they are ready to communicate. The default value is 2346.
Enable or Disable RTS/CTS protocol. It can be used in the following scenarios and used by Stations or Wireless AP.
1) When medium is too noisy or lots of interferences are present. If the
AP/Station cannot get a chance to send a packet, the RTS/CTS mechanism can be initiated to get the packet sent.
2) In mixed mode, the hidden node problem can be avoided.
The default value is 2347.
Enable or Disable to let client connect with 5G first.
Enable or Disable 802.11k, 802.11v and 802.11r.
-63-
4.7.5 Network
4.7.5.1. LAN Settings
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-35 LAN Settings
The page includes the following fields:
Object
IP Mode
LAN IP
Subnet
Gateway
Primary DNS
Secondary DNS
Description
Select “ Static IP ” or “ DHCP Client ” for setting up device IP.
Enter the AP static IP address.
Enter the network mask.
Enter the default gateway IP address.
Enter the primary DNS IP address, or not.
Enter the secondary DNS IP address, or not.
4.7.5.2. SNMP Config
Figure 5-12 SNMP Config
-64-
The page includes the following fields:
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Object
Read Community
Description
Enter the read community, default is public.
Write Community Enter the write community, default is private.
Trap Destination Address Enter the SNMP trap IP address, default is 192.168.1.100.
4.7.5.3. VLAN Settings
Figure 5-37 VLAN Settings
The page includes the following fields:
Object
AP
VLAN ID
Description
Select AP or VAP included in the VLAN.
Enter the VLAN ID from 3 to 4094.
-65-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
4.7.5.4. WAN Settings
Static IP
If your ISP offers you static IP Internet connection type, select “ Static IP " and then enter IP address, subnet mask, default gateway and primary DNS information provided by your ISP in the corresponding fields.
Figure 5-38 Static IP
The page includes the following fields:
Object
IP Address
Description
Enter the WAN IP address provided by your ISP. Enquire your ISP if you are not clear.
Subnet
Enter WAN Subnet Mask provided by your ISP.
Default Gateway
Enter the WAN Gateway address provided by your ISP.
MTU
Maximum Transmission Unit. Default is 1500.
Primary DNS
Enter the necessary DNS address provided by your ISP.
Secondary DNS
Enter the secondary DNS address provided by your ISP.
Upstream
Enter limited upstream throughput, default is 1000000 Kbps.
Downstream
Enter limited downstream throughput, default is 1000000 Kbps.
PPPoE (ADSL)
Select PPPOE if your ISP is using a PPPoE connection and provide you with PPPoE user name and password info.
-66-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-39 PPPoE (ADSL)
The page includes the following fields:
Object
Username
Description
Enter the PPPoE User Name provided by your ISP.
Password
Server Name
Enter the PPPoE password provided by your ISP.
Service Name
MTU
Enter the server description or not.
Enter the service description or not.
Set DNS Manually
Primary DNS
Maximum Transmission Unit. Default is 1452.
Enable/Disable DNS Manually.
Secondary DNS
Band Type
Enter the necessary DNS address provided by your ISP.
Enter the secondary DNS address provided by your ISP.
Upstream
Downstream
Select the band type provided by your ISP.
Enter limited upstream throughput, default is 1000000 Kbps.
Enter limited downstream throughput, default is 1000000 Kbps.
DHCP
Choose “ DHCP ” and the router will automatically obtain IP addresses, subnet masks and gateway addresses from your ISP.
-67-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-40 DHCP
The page includes the following fields:
Object
MTU
Set DNS Manually
Primary DNS
Secondary DNS
Band Type
Upstream
Downstream
Description
Maximum Transmission Unit. Default is 1452.
Enable/Disable DNS Manually.
Enter the necessary DNS address provided by your ISP.
Enter the secondary DNS address provided by your ISP.
Select the band type provided by your ISP.
Enter limited upstream throughput, default is 1000000 Kbps.
Enter limited downstream throughput, default is 1000000 Kbps.
4.7.5.5. WAN advanced settings
Figure 5-13 WAN advanced settings
-68-
The page includes the following fields:
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Object
Enable web server access on
WAN port
MAC clone
Description
Enable to access from WAN, default port is 8080
Enable Ping Access on WAN
Enable IPsec passthrough on
VPN connection
Enable PPTP passthrough on
VPN connection
Enable L2TP passthrough on
VPN connection
Enable and scan to clone the MAC address
Enable or Disable this function
Enable or disable IPSec to pass through IPSec communication data.
Enable or disable PPTP to pass through PPTP communication data.
Enable or disable L2TP to pass through L2TP communication data.
Line Detection
Enable to ping Host 1 and Host 2 IP. If ping fails, the WAN will be disconnected.
4.7.6 Security
4.7.6.1. URL Filtering
-69-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-24 URL Filtering
The page includes the following fields:
Object
Add
Delete
Apply
Status
Rule Name
Time Group
URL
Mark
Enable/disable URL filter function
Description
Press the “ Add ” button to add the rule
Press the “ Delete ” button to delete the rule
Press the “ Apply ” button to enable/disable the rule
Select ON ( Green ) or OFF ( Gray ) to enable or disable
Enter the rule name, e.g. Black list
Select Any or Customer to set up time range and work data.
Enter the URL that you need to put in black list
Enter the mark string, or not
Figure 5-43 URL Filtering
-70-
4.7.6.2. IP/Port Filtering
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-44 IP/Port Filtering
The page includes the following fields:
Object
Add
Delete
Apply
Status
Rule Name
Time Group
IP Group
IP Address
Description
Press the “ Add ” button to add the rule in the black or white list
Press the “ Delete ” button to delete the rule
Press the “ Apply ” button to enable/disable the rule
Select ON ( Green ) or OFF ( Gray ) to enable or disable
Enter the rule name, e.g. Black list
Select Any or Customer to set up time range and work data.
Select IP Group for adding IP by entering IP range or by scanning devices
Enter the IP that you need to put in black or white list
-71-
Port Range
Protocol
Mark
IP/Port Filtering Status
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Enter the web port to access
Select TCP , UDP or TCP+UDP
Enter the mark string, or not
Select the rule of IP/Port Filtering, default is Disable .
Whitelist: Allow the devices to pass in the rule
Blacklist: Prohibited rules within the device through
4.7.6.3. MAC Filtering
Figure 5-45 IP/Port Filtering
-72-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-46 MAC Filtering
The page includes the following fields:
Object
Add
Delete
Apply
Status
Rule Name
Time Group
MAC Address
Mark
MAC Filtering Status
Description
Press the “ Add ” button to add the rule in the black or white list
Press the “ Delete ” button to delete the rule
Press the “ Apply ” button to enable/disable the rule
Select ON ( Green ) or OFF ( Gray ) to enable or disable
Enter the rule name, e.g. Black list
Select Any or Customer to set up time range and work data.
Enter the MAC address that you need to put in black or white list
Enter the mark string, or not
Select the rule of MAC Filtering, default is Disable .
Whitelist: Allow the devices to pass in the rule
Blacklist: Prohibited rules within the device through
-73-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-47 IP/Port Filtering
4.7.6.4. Security (Port Mapping/Port Forwarding)
Figure 5-48 Port Mapping
The page includes the following fields:
Object
Add
Delete
Apply
Status
Rule Name
Protocol
Description
Press the “ Add ” button to add the rule in the black or white list
Press the “ Delete ” button to delete the rule
Press the “ Apply ” button to enable/disable the rule
Select ON ( Green ) or OFF ( Gray ) to enable or disable
Enter the rule name, e.g. Black list
Select TCP , UDP or TCP+UDP
-74-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
LAN IP
External Port
Internal Port
Enter the IP address that you need for port forwarding
Enter the external port range
Mark
Enable/disable Port Mapping function
Enter the internal port range
Enter the mark string, or not
Figure 5-49 Port Mapping
4.7.6.5. DMZ
Figure 5-50 DMZ
The page includes the following fields:
Object
Enable DMZ
DMZ Host IP
Description
Select Enable DMZ Host or Disable
Enter the DMZ LAN IP
-75-
4.7.7 Management
4.7.7.1. Configure
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-14 Configure
The page includes the following fields:
Object
Backup
Restore
Reset Default
Telnet
Description
Save the configuration file to your computer
Reload the configuration from your computer
Restore the factory default settings, please press this button
Enabling Telnet could be hacked, Use it carefully!
(Only for support using, default is disable)
-76-
4.7.7.2. Reboot
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-15 Reboot
The page includes the following fields:
Object
Reboot
Timed Reboot
Reboot Time
Restart Interval
Description
Reboot device immediately
Select Enable or Disable to start schedule reboot
Select reboot time for clock
Select reboot duty by day
4.7.7.3. Modify Password
Figure 5-16 Modify password
The page includes the following fields:
Object
Old Password
New Password
Description
Enter old password for change the password
Enter new password
-77-
Confirm Password
4.7.7.4. Upgrade
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Enter new password again
Figure 5-54 Upgrade Firmware
The page includes the following fields:
Object
Choose File
Whether to resume the factory configuration
Upgrade
Description
Press to select the firmware file
Select to reset the device to default when upgrading firmware
Press to upgrade the firmware
Note: Do not power off during the process of upgrading the software
4.7.7.5. Time
Figure 5-55 Setting System Time
-78-
The page includes the following fields:
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Object
System Time
NTP Enable
Time Zone Select
Description
Show system time of device
Select Enable or Disable NTP function
Manual IP Settings
NTP Server
Select time zone
Enable to manual IP setting
Sync with Host
Select NTP server
Press to sync system time with host server
Note: If you want to use any function that needs scheduling, must enable NTP function.
4.7.7.6. Log
Figure 5-56 Setup System Time
The page includes the following fields:
Object
Log
Remote Log Service
Description
Select ON/OFF to record log or not
Enable remote log server and enter the server IP address
-79-
Export
Delete
Refresh
4.7.7.7. Flow Control
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Export a log.bin file to you PC
Press to delete all of the system log
Press to refresh the system log
Figure 5-57 Setup Flow Control
The page includes the following fields:
Object
Add
Delete
Apply
Description
Press the “
Press the “
Press the “
Add ” button to add the rule in the control list
Delete
Apply
” button to delete the rule
” button to enable/disable the rule
Status
Enable/disable Port Mapping function
Select enable or disable QoS rule
Figure 5-58 Enable or Disable QoS Rule
-80-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-59 Adding rule of flow control(Speed Limit)
The page includes the following fields:
Object
Status
IP Group
IP Address
Time Group
Limited Mode
Up
Down
Mark
Description
Select enable or disable flow control rule
Select custom or Add an IP group
Enter an IP address range or use scan to select
Select any or custom or Add a Time group
Select limited mode for shared limited bandwidth or exclusive limited bandwidth
Enter the upstream limited for kbps
Enter the downstream limited for kbps
Enter the mark string, or not
-81-
4.7.7.8. IP Group
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-60 IP Group
The page includes the following fields:
Object
Add
Delete
Description
Press the “ Add ” button to add IP group in list
Press the “ Delete ” button to delete the group
Figure 5-17 Add IP Group
-82-
The page includes the following fields:
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Object
Group Name
IP Address
Mark
Description
Enter an IP group description
Enter an IP address range or use scan to select
Enter the mark string, or not
4.7.7.9. Time Group
Figure 5-62 Time Group
The page includes the following fields:
Object
Add
Delete
Description
Press the “ Add ” button to add time group in list
Press the “ Delete ” button to delete the group
-83-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-18 Add Time Group
The page includes the following fields:
Object
Time Group
Time Range
Work Date
Mark
Description
Enter an time group description
Select start time and end time for time range
Select work day by option table
Enter the mark string, or not
-84-
4.7.7.10. DDNS Setting
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-64 DDNS Setting
The page includes the following fields:
Object
DDNS
DDNS Option
User Name
Password
Domain
Public IP
No Account Registration
Forget Password
Description
Select ON ( Green ) or OFF ( Gray ) to enable or disable PLANET DDNS
Select PLANET DDNS or Easy DDNS function
Enter user account for PLANET DDNS. If you use Easy DDNS it was not necessary.
Enter password for PLANET DDNS. If you use Easy DDNS it was not necessary.
Enter unique domain name for device. If you use Easy DDNS it will be automatically generated
Public IP address is necessary for WAN IP
Hyperlink to http://www.planetddns.com/?view=registration
-85-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 5-65 PLANET EasyDDNS
-86-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Chapter 5. Quick Connection to a Wireless Network
In the following sections, the default SSID of the WDAP series is configured to “ default ”.
Windows XP (Wireless Zero Configuration)
Step 1 : Right-click on the wireless network icon displayed in the system tray
5.1
Figure 6-1 System Tray – Wireless Network Icon
Step 2 : Select [ View Available Wireless Networks ]
Step 3 : Highlight and select the wireless network (SSID) to connect
(1) Select SSID [default]
(2) Click the [ Connect ] button
Figure 6-2 Choosing a Wireless Network
-87-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Step 4 : Enter the encryption key of the wireless AP
(1) The Wireless Network Connection box will appear
(2) Enter the encryption key that is configured in section 5.7.2.1
(3) Click the [Connect] button
Figure 6-3 Entering the Network Key
Step 5 : Check if “ Connected ” is displayed
Figure 6-4 Choosing a Wireless Network -- Connected
Some laptops are equipped with a “Wireless ON/OFF” switch for the internal wireless LAN. Make sure the hardware wireless switch is switched to “ON” position.
-88-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Windows 7/8/10 (WLAN AutoConfig)
WLAN AutoConfig service is built-in in Windows 7 that can be used to detect and connect to wireless network.
This built-in wireless network connection tool is similar to wireless zero configuration tool in Windows XP.
5.2
Step 1 : Right-click on the network icon displayed in the system tray
Figure 6-5 Network Icon
Step 2 : Highlight and select the wireless network (SSID) to connect
(1) Select SSID [ default ]
(2) Click the [ Connect ] button
Figure 6-6 WLAN AutoConfig
If you will be connecting to this Wireless AP in the future, check [ Connect automatically ].
-89-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Step 4 : Enter the encryption key of the wireless AP
(1) The Connect to a Network box will appear.
(2) Enter the encryption key that is configured in section 5.7.2.1
(3) Click the [OK] button.
Figure 6-7 Typing the Network Key
Figure 6-8 Connecting to a Network
-90-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Step 5 : Check if “ Connected ” is displayed.
Figure 6-9 Connected to a Network
-91-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Mac OS X 10.x
In the following sections, the default SSID of the WDAP series is configured to “default”.
Step 1 : Right-click on the network icon displayed in the system tray
5.3
The AirPort Network Connection menu will appear.
Figure 6-10 Mac OS – Network Icon
Step 2 : Highlight and select the wireless network (SSID) to connect
(1) Select and SSID [ default ].
(2) Double-click on the selected SSID.
Figure 6-11 Highlighting and Selecting the Wireless Network
-92-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Step 4 : Enter the encryption key of the wireless AP
(1) Enter the encryption key that is configured in section 5.7.2.1
(2) Click the [OK] button.
Figure 6-12 Enter the Password
If you will be connecting to this Wireless AP in the future, check [ Remember this network ].
-93-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Step 5 : Check if the AirPort is connected to the selected wireless network.
If “Yes”, then there will be a “check” symbol in front of the SSID.
Figure 6-13 Connected to the Network
-94-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
There is another way to configure the MAC OS X wireless settings:
Step 1 : Click and open the [ System Preferences ] by going to Apple > System Preference or Applications
Figure 6-14 System Preferences
Step 2 : Open Network Preference by clicking on the [ Network ] icon
Figure 6-15 System Preferences -- Network
-95-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Step 3 : Check Wi-Fi setting and select the available wireless network
(1) Choose the AirPort on the left menu (make sure it is ON)
(2) Select Network Name [ default ] here
If this is the first time to connect to the Wireless AP, it should show “No network selected”.
Figure 6-16 Selecting the Wireless Network
-96-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
iPhone/iPod Touch/iPad
In the following sections, the default SSID of the WDAP series is configured to “ default ”.
Step 1 : Tap the [ Settings ] icon displayed in the home screen
5.4
Figure 6-17 iPhone – Settings icon
Step 2 : Check Wi-Fi setting and select the available wireless network
(1) Tap [ General ] \ [ Network ]
(2) Tap [ Wi-Fi ]
If this is the first time to connect to the Wireless AP, it should show “Not Connected”.
Figure 6-18 Wi-Fi Setting
-97-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Figure 6-19 Wi-Fi Setting – Not Connected
Step 3 : Tap the target wireless network (SSID) in “ Choose a Network… ”
(1) Turn on Wi-Fi by tapping “ Wi-Fi ”
(2) Select SSID [ default ]
Figure 6-20 Turning on Wi-Fi
-98-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Step 4 : Enter the encryption key of the Wireless AP
(1) The password input screen will be displayed.
(2) Enter the encryption key that is configured in section 5.7.2.1
(3) Tap the [ Join ] button.
Figure 6-21 iPhone -- Entering the Password
-99-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Step 5 : Check if the device is connected to the selected wireless network.
If “Yes”, then there will be a “check” symbol in front of the SSID.
Figure 6-22 iPhone -- Connected to the Network
-100-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Appendix A: Planet Smart Discovery Utility
To easily list the WDAP series in your Ethernet environment, the Planet Smart Discovery Utility is an ideal solution.
The following installation instructions guide you to running the Planet Smart Discovery Utility.
Step 1 : Deposit the Planet Smart Discovery Utility in administrator PC.
Step 2 : Run this utility and the following screen appears.
Step 3 : Press “Refresh” for the current connected devices in the discovery list as shown in the following screen:
Step 3 : Press “Connect to Device” and then the Web login screen appears.
The fields in white background can be modified directly and then you can apply the new setting by clicking “ Update Device ”.
-101-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Appendix B: FAQs
Q1: How to Set Up the AP Client Connection
Topology:
-102-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Step 1 . Use static IP in the PCs that are connected with AP-1(Site-1) and AP-2(Site-2). In this case, Site-1 is
“ 192.168.1.100
”, and Site-2 is “ 192.168.1.200
”.
Step 2 . In AP-2, change the default IP to the same IP range but different from AP-1. In this case, the IP is changed to 192.168.1.252
.
Step 3 . In AP-1, go to “ Wizard ” to configure it to AP Mode . In AP-2, configure it to Repeater Mode .
AP-1
-103-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
AP-2
Step 4 . In AP-2, press Scan AP to search the AP-1. You can also enter the MAC address, SSID, encryption and bandwidth if you know what they are.
-104-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Step 5 . Click “ Next ” to finish the setting.
Step 6 . Click “ Repeater Information ” to check connection status.
【 Remark 】 If the signal was too high or too low that will effects the connection quality, please adjust the
Tx power from web GUI or antenna to get best value about -60~-65 dBm.
Wireless Signal Status
Too Strong
Strong
Good
Bad
Very Bad
Signal (dBm)
>-60dBm
-61dBm~-70 dBm
-71dBm~-80 dBm
-81dBm~-90 dBm
<-90dBm
-105-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Step 7 . Use command line tool to ping each other to ensure the link is successfully established.
From Site-1, ping 192.168.1.200; and in Site-2, ping 192.168.1.100.
Step 8 . Configure the TCP/IP settings of Site-2 to “ Obtain an IP address automatically ”.
-106-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Step 9 . Use command line tool to ping the DNS (e.g., Google) to ensure Site-2 can access internet through the wireless connection.
The following hints should be noted:
1) The encryption method must be the same as that of both sites if configured.
2) Both sites should be Line-of-Sight.
3) For the short distance connection less than 1km, please reduce the "RF Output Power" of both sites.
4) For the long distance connection over 1km, please adjust the "Distance" to the actual distance or double the actual distance.
-107-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Q2: How to set up the WDS Connection
Topology:
Step 1 . Use static IP in the PCs that are connected with WDAP-C7210E-1 (Site-1) and WDAP-C7210E-2
(Site-2). In this case, Site-1 is “ 192.168.1.100
”, and Site-2 is “ 192.168.1.200
”.
-108-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Step 2 . In AP-2, change the default IP to the same IP range but different from AP-1. In this case, the IP is changed to 192.168.1.252
.
Step 3 . In both APs, go to “ Wizard ” to configure it in Super WDS Mode.
Step 4 . In AP1 set up WDS SSID, for example WDS-1. Select Encrypt for WEP and enter password.
-109-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Step 5 . Finish the 2.4G/5G Wi-Fi and LAN setting.
Step 6 . Click “ Home ” to check WDS status.
Step 7 . In AP2 scan AP1 WDS SSID, for example WDS-1. Select Encrypt for WEP and enter password.
-110-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
-111-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Step 8 . Confirm SSID and MAC. Select Encrypt for WEP and enter password.
Step 9 . Finish the 5G Wi-Fi and LAN setting.
Step 10 . Go to “ WDS Information ” to check connection status.
-112-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Step 11 . Use command line tool to ping each other to ensure the link is successfully established.
From Site-1, ping 192.168.1.200; and in Site-2, ping 192.168.1.100.
The following hints should be noted:
1) The encryption method must be the same as that of both sites if configured.
2) Both sites should be Line-of-Sight.
3) For the short distance connection less than 1m, please reduce the "RF Output Power" of both sites.
4) For the long distance connection over 1m, please adjust the "Distance" to the actual distance or double the actual distance.
-113-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Appendix C: Troubleshooting
If you find the AP is working improperly or stop responding to you, please read this troubleshooting first before contacting the dealer for help. Some problems can be solved by yourself within a very short time.
Scenario Solution
The AP is not responding to me when I want to access it by Web browser. a. Please check the connection of the power cord and the
Ethernet cable of this AP. All cords and cables should be correctly and firmly inserted into the AP. b. If all LEDs on this AP are off, please check the status of power adapter, and make sure it is correctly powered. c. You must use the same IP address section which AP uses. d. Are you using MAC or IP address filter? Try to connect the AP by another computer and see if it works; if not, please reset the AP to the factory default settings by pressing the ‘reset’ button for over 7 seconds. e. Use the Smart Discovery Tool to see if you can find the
AP or not. f. If you did a firmware upgrade and this happens, contact your dealer of purchase for help. g. If all the solutions above don’t work, contact the dealer for help.
I can’t get connected to the
Internet. a. Go to ‘Status’ -> ‘Internet Connection’ menu on the router connected to the AP, and check Internet connection status. b. Please be patient. Sometimes Internet is just that slow. c. If you’ve connected a computer to Internet directly before, try to do that again, and check if you can get connected to Internet with your computer directly attached to the device provided by your Internet service provider. d. Check PPPoE / L2TP / PPTP user ID and password entered in the router’s settings again. e. Call your Internet service provider and check if there’s something wrong with their service. f. If you just can’t connect to one or more website, but you can still use other internet services, please check
URL/Keyword filter. g. Try to reset the AP and try again later. h. Reset the device provided by your Internet service provider too.
-114-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Scenario Solution i. Try to use IP address instead of host name. If you can use IP address to communicate with a remote server, but can’t use host name, please check DNS setting.
I can’t locate my AP by my a. ‘Broadcast ESSID’ set to off? wireless device. b. Both two antennas are properly secured. c. Are you too far from your AP? Try to get closer. d. Please remember that you have to input ESSID on your wireless client manually, if ESSID broadcast is disabled.
File downloading is very slow or breaks frequently.
I can’t log into the web management interface; the password is wrong.
The AP becomes hot a. Internet is slow sometimes. Please be patient. b. Try to reset the AP and see if it’s better after that. c. Try to know what computers do on your local network. If someone’s transferring big files, other people will think
Internet is really slow. d. If this never happens before, call you Internet service provider to know if there is something wrong with their network. a. Make sure you’re connecting to the correct IP address of the AP! b. Password is case-sensitive. Make sure the ‘Caps Lock’ light is not illuminated. c. If you really forget the password, do a hard reset. a. This is not a malfunction, if you can keep your hand on the AP’s case. b. If you smell something wrong or see the smoke coming out from AP or A/C power adapter, please disconnect the AP and power source from utility power (make sure it’s safe before you’re doing this!), and call your dealer of purchase for help.
-115-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
Appendix D: Glossary
802.11ac
- 802.11ac is a wireless networking standard in the 802.11
family (which is marketed under the brand name Wi-Fi), developed in the IEEE Standards Association process, providing high-throughput wireless local area networks (WLANs) on the 5 GHz band .
802.11n 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding. The Enhanced Wireless Consortium (EWC) [3] was formed to help accelerate the IEEE 802.11n development process and promote a technology specification for interoperability of next-generation wireless local area networking (WLAN) products.
802.11a
- 802.11a was an amendment to the IEEE 802.11 wireless local network specifications that defined requirements for an orthogonal frequency division multiplexing (OFDM) communication system. It was originally designed to support wireless communication in the unlicensed national information infrastructure (U-NII) bands (in the 5–6 GHz frequency range) as regulated in the United
States by the Code of Federal Regulations, Title 47, Section 15.407.
802.11b - The 802.11b standard specifies a wireless networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.4GHz, and
WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks.
802.11g - specification for wireless networking at 54 Mbps using direct-sequence spread-spectrum
(DSSS) technology, using OFDM modulation and operating in the unlicensed radio spectrum at
2.4GHz, and backward compatibility with IEEE 802.11b devices, and WEP encryption for security.
DDNS ( D ynamic D omain N ame S ystem) - The capability of assigning a fixed host and domain name to a dynamic Internet IP Address.
DHCP ( D ynamic H ost C onfiguration P rotocol) A protocol that automatically configure the TCP/IP parameters for the all the PC(s) that are connected to a DHCP server.
DMZ ( D e m ilitarized Z one) A Demilitarized Zone allows one local host to be exposed to the Internet for a special-purpose service such as Internet gaming or videoconferencing.
DNS ( D omain N ame S ystem) An Internet Service that translates the names of websites into IP addresses.
Domain Name - A descriptive name for an address or group of addresses on the Internet.
DSL ( D igital S ubscriber L ine) A technology that allows data to be sent or received over existing traditional phone lines.
MTU ( Maximum Transmission Unit ) The size in bytes of the largest packet that can be transmitted.
-116-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
NAT ( N etwork A ddress T ranslation) NAT technology translates IP addresses of a local area network to a different IP address for the Internet.
PPPoE ( P oint to P oint P rotocol o ver E thernet) PPPoE is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection.
SSID - A S ervice S et Id entification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name.
WEP ( W ired E quivalent P rivacy) A data privacy mechanism based on a 64-bit or 128-bit or 152-bit shared key algorithm, as described in the IEEE 802.11 standard.
Wi-Fi - A trade name for the 802.11b wireless networking standard, given by the Wireless Ethernet
Compatibility Alliance (WECA, see http://www.wi-fi.net), an industry standards group promoting interoperability among 802.11b devices.
WLAN ( W ireless L ocal A rea N etwork) A group of computers and associated devices communicate with each other wirelessly, which network serving users are limited in a local area.
-117-
User Manual of WDAP-C7210E_WDAP-W1200E_WDAP-850AC
EC Declaration of Conformity
Lietuviškai English
Hereby, PLANET Technology Corporation, declares that this 11ac Wireless AP is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
Česky
Společnost
PLANET Technology Corporation, tímto prohlašuje, že tato 11ac Wireless AP splňuje základní požadavky a další příslušná ustanovení směrnice
2014/53/EU.
Magyar
Dansk
Deutsch
Eestikeeles
Ελληνικά
Español
Français
Italiano
Latviski
PLANET Technology Corporation, erklærer herved, at følgende udstyr 11ac Wireless AP overholder de væsentlige krav og øvrige relevante krav i direktiv 2014/53/EU
Malti
Hiermit erklärt PLANET Technology Corporation, dass sich dieses Gerät 11ac Wireless AP in
Übereinstimmung mit den grundlegenden
Anforderungen und den anderen relevanten
Vorschriften der Richtlinie 2014/53/EU befindet".
(BMWi)
Nederlands
Polski
Käesolevaga kinnitab PLANET Technology
Corporation, et see 11ac Wireless AP vastab
Euroopa Nõukogu direktiivi 2014/53/EU põhinõuetele ja muudele olulistele tingimustele.
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ
, PLANET Technology
Corporation,
ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ 11ac Wireless
AP
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ
ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ
2014/53/EU
Por medio de la presente, PLANET Technology
Corporation, declara que 11ac Wireless AP cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 2014/53/EU
Par la présente, PLANET Technology
Corporation, déclare que les appareils du 11ac
Wireless AP sont conformes aux exigences essentielles et aux autres dispositions pertinentes de la directive 2014/53/EU
Con la presente , PLANET Technology
Corporation, dichiara che questo 11ac Wireless
AP è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva
2014/53/EU.
Português
Slovensky
Slovensko
Suomi
Svenska
Ar šo PLANET Technology Corporation, apliecina, ka šī
11ac Wireless AP atbilst
Direktīvas
2014/53/EU pamatprasībām un citiem atbilstošiem noteikumiem.
Šiuo PLANET Technology Corporation, , skelbia, kad 11ac Wireless AP tenkina visus svarbiausius
2014/53/EU direktyvos reikalavimus ir kitas svarbias nuostatas.
A gyártó PLANET Technology Corporation , kijelenti, hogy ez a 11ac Wireless AP megfelel az 2014/53/EU irányelv alapkövetelményeinek és a kapcsolódó rendelkezéseknek.
Hawnhekk, PLANET Technology Corporation, jiddikjara li dan 11ac Wireless AP jikkonforma malħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 2014/53/EU
Hierbij verklaart , PLANET Technology orporation, dat
11ac Wireless AP
in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 2014/53/EU
Niniejszym firma PLANET Technology Corporation, oświadcza, że
11ac Wireless AP spełnia wszystkie istotne wymogi i klauzule zawarte w dokumencie
„Directive 2014/53/EU .
PLANET Technology Corporation , declara que este
11ac Wireless AP está conforme com os requisitos essenciais e outras disposições da Directiva
2014/53/EU .
Výrobca PLANET Technology Corporation, týmto deklaruje, že táto 11ac Wireless AP je v súlade so základnými požiadavkami a ďalšími relevantnými predpismi smernice 2014/53/EU.
PLANET Technology Corporation , s tem potrjuje, da je ta 11ac Wireless AP skladen/a z osnovnimi zahtevami in ustreznimi določili Direktive
2014/53/EU
PLANET Technology Corporation, vakuuttaa täten että 11ac Wireless AP tyyppinen laite on direktiivin
2014/53/EU oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Härmed intygar, PLANET Technology Corporation, att denna 11ac Wireless AP står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv
2014/53/EU .
-118-
Advertisement