Advertisement
Advertisement
Copyright
Copyright 2015 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environme nt. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense. Any changes or modifications not expressly approved by PLANET could void the user’s authority to operate this equipment under the rules and regulations of the FCC.
FCC Caution:
To assure continued compliance, (for example, use only shielded interface cables when connecting to computer or peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undesired operation.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.
I
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation. For energy saving, please remove the DC-plug to disconnect the device from the power circuit. Without removing the DC-plug, the device still consumes power from the power circuit. In view of Saving the Energy, it is strongly suggested to remove the DC-plug for the device if this device is not intended to be active.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and
Satellite Earth Station Equipment) as of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and thus,
WEEE has to be collected separately.
II
Revision
User’s Manual of PLANET 802.11a/n Outdoor Wireless CPE
Model: WNAP-7325 / WNAP-7335
Rev: 1.0 (May, 2015)
Part No. EM-WNAP-7325_v1.0 ( 2081-E10580-000 ) / EM-WNAP-7335_v1.0 ( 2081-E10610-000 )
III
CONTENTS
IV
V
FIGURES
...................................................................................... 41
VI
VII
User Manual of WNAP-7325/WNAP-7335
Chapter 1. Product Introduction
1.1 Package Contents
Thank you for choosing PLANET WNAP-7325 series. Before installing the AP, please verify the contents inside the package box.
WNAP-7325 / WNAP-7335 Quick Installation Guide
PoE Injector & Power Cord Plastic Strap x 1
If there is any item missing or damaged, please contact the seller immediately.
-8-
1.2 Product Description
User Manual of WNAP-7325/WNAP-7335
PLANET WNAP-7325/WNAP-7335 Outdoor Wireless Access Point provides a higher transmission speed, higher power and better performance designed for outdoor wireless application.
Faster Speed and longer Distance
Adopting the IEEE 802.11n advanced 2T2R MIMO technology, the WNAP-7325 and WNAP-7335 provide high speed, reliable wireless network coverage, and incredible improvement in the wireless performance. As an IEEE
802.11a/n compliant wireless device, the WNAP-7325 and WNAP-7335 are able to give stable and efficient wireless performance for long distance application. Thus, it delivers a data rate of up to 300Mbps three times faster than the normal 802.11a wireless device. With its adjustable output power up to 500mW, it can extend the coverage of an outdoor area.
Multiple Operation and Wireless Modes
The WNAP-7325 and WNAP-7335 support multiple wireless communication connectivities (AP, Client CPE,
WDS PtP, WDS PtMP and WISP), meeting user’s application requirements. It also helps user to easily extend the existing wireless network.
Advanced Wireless Security
In aspect of security, besides 64/128- bit WEP encryption, the WNAP-7325 and WNAP-7335 are integrated with
WPA / WPA2, WPA-PSK / WPA2-PSK and 802.1x RADIUS authentication to secure and protect your wireless
LAN. The wireless MAC filtering and SSID broadcast help to consolidate the wireless network security and prevent unauthorized wireless connection.
Perfect Solution for Outdoor Environment
The WNAP-7325 and WNAP-7335 are perfectly suitable to be installed in outdoor environments. With its IP55 casing protection, the WNAP-7325 and WNAP-7335 can perform normally under rigorous weather conditions including heavy rain and wind.
With the passive Power over Ethernet (PoE) design, the WNAP-7325 and
WNAP-7335 can be easily installed in the areas where power outlets are not available. Thus, the WNAP-7325 and WNAP-7335 are ideal for outdoor wireless access applications between buildings on campuses, and in business and rural areas.
Easy Installation and Management
With user-friendly Web UI and step by step Setup Wizard, user can set up a wireless network without any difficulty.
-9-
User Manual of WNAP-7325/WNAP-7335
1.3 Product Features
Industrial Compliant Wireless LAN & LAN
Compliant with the IEEE 802.11n wireless technology (with data rate of up to 300Mbps)
Backward compatible with 802.11a standard
Equipped with 10/100Mbps RJ45 ports for LAN & WAN; auto MDI/ MDI-X supported
Fixed-network Broadband Router
Supported connection types: Dynamic IP, Static IP, PPPoE
Supports Virtual Server, DMZ for various networking applications
Supports DHCP Server, UPnP, Dynamic DNS
RF Interface Characteristics
Built-in 14dBi Dual-Polarization Antenna (WNAP-7325)
Built-in RP-SMA antenna connectors (WNAP-7335)
High Output Power Up to 500mW with multiple adjustable transmit power control
Outdoor Environmental Characteristics
IP55
Passive Power over Ethernet design
Operating temperature: -20~70°C
Multiple Operation and Wireless Modes
Multiple operation modes: Bridge, WISP
Multiple wireless modes: AP, Client CPE(WISP), WDS PtP, WDS PtMP
Supports multiple SSIDs to allow users to access different networks through a single AP
Supports WMM (Wi-Fi multimedia)
Secure Network Connection
Supports software Wi-Fi Protected Setup (WPS)
Advanced security: 64/128-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK(TKIP/AES) and 802.1x authentication
Supports IP / Protocol-based access control and MAC filtering
Easy Installation and Management
Web-based UI and quick Setup Wizard for easy configuration
SNMP-based management interface
System status monitoring includes DHCP Client, System Log
-10-
User Manual of WNAP-7325/WNAP-7335
1.4 Product Specifications
Product
WNAP-7325 WNAP-7335
300Mbps 802.11a/n Wireless Outdoor CPE
Hardware
Standard Support
Chipset
Operating Channel
IEEE802.11a/n
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
Atheros AR9344
Memory
PoE
64 Mbytes DDR SDRAM
16 Mbytes Flash
Passive PoE
Interface
Antenna
Data Rate
Wireless IEEE802.11a/n, 2T2R
PoE LAN (LAN 1): 1 x 10/100BASE-TX, auto-MDI/MDIX, passive PoE
LAN 2: 1 x 10/100BASE-TX, auto-MDI/MDIX, passive PoE out pass-through
Built-in 14dBi Dual-Polarization
Antenna
- Vertical: 20 degrees
- Horizontal: 30 degrees
Built-in RP-SMA antenna connectors
IEEE 802.11a: 6, 9, 12, 18, 24, 36, 48, 54Mbps
IEEE 802.11n (20MHz): up to 150Mbps
IEEE 802.11n (40MHz): up to 300Mbp
Media Access Control CSMA/CA
Modulation
Frequency Band
Transmission/Emission type: OFDM
Data modulation type: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
5.180GHz ~ 5.825GHz
5.180GHz CH36 5.580GHz CH116
5.200GHz CH40 5.600GHz CH120
5.220GHz CH44 5.620GHz CH124
5.240GHz CH48 5.640GHz CH128
5.260GHz CH52 5.660GHz CH132
5.280GHz CH56 5.680GHz CH136
5.300GHz CH60 5.700GHz CH140
5.320GHz CH64 5.745GHz CH149
5.500GHz CH100 5.765GHz CH153
5.520GHz CH104 5.785GHz CH157
5.540GHz CH108 5.805GHz CH161
5.560GHz CH112 5.825GHz CH165
*The 24 channels are defined by the theory. The actual application will vary based on the regulation in different regions and countries.
-11-
User Manual of WNAP-7325/WNAP-7335
RF Output Power (dBm)
802.11a: up to 26 ± 1
802.11n: up to 25 ± 1
Receiver Sensitivity
(dBm)
802.11a: -94 dBm
802.11n: -93 dBm
Output Power Control 12~27dBm
Power Consumption 12W
LAN
Power Requirements
24VDC, 1A/ Passive PoE
Pin 4,5 VDC+
Pin 7,8 VDC-
Pin 3 Reset
Environment & Certification
Operating Temperature -20~70°c
Operating Humidity 10~95% non-condensing
IP Level IP55
Regulatory CE, FCC, RoHS
Software
LAN
WAN
Operation Modes
Firewall
Wireless Modes
Built-in DHCP server supporting static IP address distribution
Support 802.1d STP (Spanning Tree)
Static IP
Dynamic IP
PPPoE
Bridge
WISP
NAT firewall with SPI (Stateful Packet Inspection)
Built-in NAT server supporting Virtual Server, and DMZ
Built-in firewall with Port/ IP address/ MAC/ URL filtering
AP
Client
WDS PTP
WDS PTMP
WISP
Channel Width
Wireless Isolation
20MHz / 40MHz
Enable it to isolate each connected wireless client so that they cannot access mutually.
Encryption Type 64/128-bit WEP, WPA, WPA-PSK, WPA2, WPA2-PSK, 802.1X
Wireless Security
Provides wireless LAN ACL (Access Control List) filtering
Wireless MAC address filtering
Enable/Disable SSID Broadcast
Max. Wireless Clients 25
Max. WDS Peers 8
Max. Wired Clients 60
-12-
User Manual of WNAP-7325/WNAP-7335
Chapter 1. Product Introduction
1.1 Package Contents
Thank you for choosing PLANET WNAP-7325 series. Before installing the AP, please verify the contents inside the package box.
WNAP-7325 / WNAP-7335 Quick Installation Guide
PoE Injector & Power Cord Plastic Strap x 1
If there is any item missing or damaged, please contact the seller immediately.
-8-
User Manual of WNAP-7325/WNAP-7335
Chapter 2. Hardware Installation
Please follow the instructions below to connect the WNAP-7325 and WNAP-7335 to the existing network devices and your computers.
2.1 Hardware Description
Dimensions : 127 x 63 x 254 mm (W x D x H)
Appearance
Figure 2-1 Three-way View
-14-
User Manual of WNAP-7325/WNAP-7335
Rear Panel – LED
Figure 2-2 LED
LED Definition
LED
Power
State Meaning
Signal Indicator
(Client Mode)
On Indicates the wireless signal strength of remote AP
LAN 1
LAN 2
On
Off
On
Off
2.1.1 The Bottom Panel – Port
Port linked.
No link.
Port linked.
No link.
Table 2-1 The LED indication
The Bottom panel provides the physical connectors connected to the power adapter and any other network device. Figure 2-3 shows the bottom panel of the WNAP-7325 and WNAP-7335.
-15-
Bottom Panel
User Manual of WNAP-7325/WNAP-7335
Figure 2-3 WNAP-7325 Bottom Panel
PoE Injector
Reset Button
Figure 2-4 WNAP-7335 Bottom Panel
Figure 2-5 PoE Injector
-16-
User Manual of WNAP-7325/WNAP-7335
H/W Interface Definition
Object
PoE LAN
(Passive PoE)
LAN 2
Reset
Description
10/100Mbps RJ45 port , auto MDI/ MDI-X and passive PoE supported
Connect LAN port to the PoE injector to power on the device.
Pin assignment:
Pin 4, 5 (+)
Pin 7, 8 (-)
Pin 3 (Reset)
10/100Mbps RJ45 port , auto MDI/ MDI-X
Connect this port to the network equipment.
※ When the option “ Enable POE Pass Through ” on the System
Management page is checked, the LAN2 can supply passive PoE power to the second WNAP-7325 or WNAP-7335 through LAN 2.
Press the Reset button on the device or on the PoE injector over 5 seconds to return to factory default setting.
※ If you have connected with the ELA-100, please DO NOT press the reset button on the PoE injector to prevent the ELA-100 from being damaged.
Table 2-2 The PoE Injector Indication
-17-
User Manual of WNAP-7325/WNAP-7335
Chapter 3. Connecting to the AP
3.1 Preparation before Installation
3.1.1 Professional Installation Required
Please seek assistance from a professional installer who is well trained in the RF installation and knowledgeable in the local regulations.
3.1.2 Safety Precautions
1. To keep you safe and install the hardware properly, please read and follow these safety precautions.
2. If you are installing the WNAP-7325 or WNAP-7335 for the first time, for your safety as well as others’, please seek assistance from a professional installer who has received safety training on the hazards involved.
3. Keep safety as well as performance in mind when selecting your installation site, especially where there are electric power and phone lines.
4. When installing the WNAP-7325 or WNAP-7335, please note the following things:
Do not use a metal ladder;
Do not work on a wet or windy day;
Wear shoes with rubber soles and heels, rubber gloves, long sleeved shirt or jacket.
5. When the system is operational, avoid standing directly in front of it. Strong RF fields are present when the transmitter is on.
3.2 Installation Precautions
Users MUST use a proper and well-installed surge arrestor and grounding kit with the WNAP-7325 or
WNAP-7335; otherwise, a random lightning could easily cause fatal damage to the WNAP-7325 or
WNAP-7335. EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.
Users MUST use the “Power cord and PoE Injector” shipped in the box with the WNAP-7325 or
WNAP-7335. Use of other options will cause damage to the WNAP-7325 or WNAP-7335.
-18-
User Manual of WNAP-7325/WNAP-7335
OUTDOOR INSTALLATION WARNING
!
IMPORTANT SAFETY PRECAUTIONS:
LIVES MAY BE AT RISK!
Carefully observe these instructions and any special instructions that are included with the equipment you are installing.
CONTACTING POWER LINES CAN BE LETHAL. Make sure no power lines are anywhere where possible contact can be made. Antennas, masts, towers, guy wires or cables may lean or fall and contact these lines. People may be injured or killed if they are touching or holding any part of equipment when it contacts electric lines. Make sure that equipment or personnel do not come in contact directly or indirectly with power lines.
The horizontal distance from a tower, mast or antenna to the nearest power line should be at least twice the total length of the mast/antenna combination. This will ensure that the mast will not contact power if it falls either during installation or later.
TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND.
Select equipment locations that will allow safe, simple equipment installation.
Don’t work alone. A friend or co-worker can save your life if an accident happens.
Use approved non-conducting lasers and other safety equipment. Make sure all equipment is in good repair.
If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it fall.
If anything such as a wire or mast does come in contact with a power line, DON’T TOUCH IT OR ATTEMPT TO
MOVE IT . Instead, save your life by calling the power company.
Don’t attempt to erect antennas or towers on windy days.
MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES CONNECTED TO
ANTENNAS HAVE LIGHTNING ARRESTORS.
This will help prevent fire damage or human injury in case of lightning, static build-up, or short circuit within equipment connected to the antenna.
The base of the antenna mast or tower must be connected directly to the building protective ground or to one or more approved grounding rods, using 1 OAWG ground wire and corrosion-resistant connectors.
Refer to the National Electrical Code for grounding details.
IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:
DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.
Use a non-conductive dry board, stick or rope to push or drag them so they no longer are in contact with electrical power.
Once they are no longer contacting electrical power, administer CPR if you are certified, and make sure that emergency medical aid has been requested.
-19-
User Manual of WNAP-7325/WNAP-7335
3.3 Installing the AP
Please install the AP according to the following steps. Don't forget to pull out the power plug and keep your hands dry.
Step 1. Push the latch in the bottom of the WNAP-7325 or WNAP-7335 to remove the sliding cover.
Figure 3-1 Connect the Antenna
Step 2. Plug the RJ45 Ethernet cable into the PoE LAN Port of the WNAP-7325 or WNAP-7335. Connecting the external antenna to the RP-SMA connectors if you are using the WNAP-7335.Then, slide back the cover to finish the installation.
Figure 3-2 WNAP-7325 Connect the Ethernet cable
Figure 3-3 WNAP-7335 Connect the Ethernet cable
-20-
User Manual of WNAP-7325/WNAP-7335
Step 3. Plug the power cord into the DC port and the other end into the AC socket. Then, plug the RJ45 cable
(as shown in picture 4 under Step 1) into the POE port of the PoE injector.
Figure 3-4 Connect the PoE injector
Figure 3-5 Connect the PoE injector
-21-
User Manual of WNAP-7325/WNAP-7335
3.4 Standard Pole Mounting
Place the strap through the slots on the back of the WNAP-7325 or WNAP-7335 and then around the pole.
Tighten the strap to secure the WNAP-7325 or WNAP-7335.
Figure 3-6 WNAP-7325 Pole Mounting
Figure 3-7 WNAP-7335 Pole Mounting
-22-
User Manual of WNAP-7325/WNAP-7335
Chapter 4. Quick Installation Guide
This chapter will show you how to configure the basic functions of your AP within minutes.
A computer with wired Ethernet connection to the Wireless AP is required for the first-time configuration.
4.1 Manual Network Setup - TCP/IP Configuration
The default IP address of the WNAP-7325 and WNAP-7335 is 192.168.1.253
. And the default Subnet Mask is
255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for description.
Connect the WNAP-7325 or WNAP-7335 with your PC via an Ethernet cable which is then plugged into a LAN port of the PoE injector with one end and into a LAN port of the PC with the other end. Then power on the
WNAP-7325 or WNAP-7335 via PoE injector or PoE switch.
In the following sections, we’ll introduce how to install and configure the TCP/IP correctly in Windows 7 . And the procedures in other operating systems are similar. First, make sure your Ethernet adapter is working, and refer to the Ethernet adapter’s manual if needed.
4.1.1 Configuring the IP Address Manually
Summary:
Set up the TCP/IP Protocol for your PC.
Configure the network parameters. The IP address is 192.168.1.xxx ("xxx" is any number from 2 to
252), Subnet Mask is 255.255.255.0, and Gateway is 192.168.1.253 (The AP's default IP address)
1 Select Use the following IP address radio button.
2 If the AP's LAN IP address is 192.168.1.1, enter IP address 192.168.1.x (x is from 2 to 254), and Subnet mask 255.255.255.0.
3 Select Use the following DNS server addresses radio button. In the Preferred DNS Server field, you can enter the DNS server IP address which has been provided by your ISP
-23-
User Manual of WNAP-7325/WNAP-7335
Figure 4-1 TCP/IP Setting
Now click OK to save your settings.
Now, you can run the ping command in the command prompt to verify the network connection between your
PC and the AP. The following example is in Windows 7 OS. Please follow the steps below: on .
2. Type ” in the Search box.
-24-
User Manual of WNAP-7325/WNAP-7335
Figure 4-2 Windows Start Menu
3. Open a command prompt and type ping 192.168.1.253
, and then press Enter .
If the result displayed is similar to Figure 4-3 , it means the connection between your PC and the AP has been established well.
Figure 4-3 Successful result of Ping command
If the result displayed is similar to Figure 4-4 , it means the connection between your PC and the AP has failed.
-25-
User Manual of WNAP-7325/WNAP-7335
Figure 4-4 Failed result of Ping command
If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your AP. Some firewall software programs may block a DHCP request on newly installed adapters.
4.2 Starting Setup in the Web UI
It is easy to configure and manage the WNAP-7325 or WNAP-7335 with the web browser.
Step 1. To access the configuration page, open a web browser and enter the default IP address http://192.168.1.253
in the web address field of the browser.
Figure 4-5 Login by default IP address
After a moment, a login window will appear. Enter admin for the User Name and Password, both in lower case letters. Then click the OK button or press the Enter key.
-26-
User Manual of WNAP-7325/WNAP-7335
Figure 4-6 Login Window
Default IP Address: 192.168.1.253
Default User Name: admin
Default Password: admin
If the above screen does not pop up, it may mean that your web browser has been set to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it.
After entering the username and password, the Operation Mode page screen appears as in Figure 4-8
Figure 4-7 Web UI Screenshot
-27-
User Manual of WNAP-7325/WNAP-7335
Step 2. You can choose an Operation Mode. Please refer to the instructions in the next chapter for configuring the other Operation Modes.
Figure 4-8 Choose Operation Mode
Step 3. Please enter the SSID and configure your Encryption Settings, Pre-Shared Key, etc. Then click the
Save button to make the configuration take effect immediately.
Figure 4-9 Configure Wireless Settings
-28-
User Manual of WNAP-7325/WNAP-7335
Chapter 5. Configuring the AP
This chapter delivers a detailed presentation of AP’s functionalities and features under 4 main menus
( Operation Mode , System Configuration , Tools and Device Status ) below, allowing you to manage the AP with ease.
Figure 5-1 Main Menu
5.1 Operation Modes
On this page, you can select different operation modes of the AP, including:
Access Point
Client
WDS AP
WDS Client
AP Router
Wireless ISP
Figure 5-2 Operation Modes
-29-
5.1.1 Access Point
User Manual of WNAP-7325/WNAP-7335
Click “ Operation Mode ” “ Access Point ” and the following page will be displayed. This section allows you to configure the Access Point mode.
Object
Regulatory Domain
Network SSID
Figure 5-3 Basic Settings - AP
Description
Select your domain from the list.
It is the wireless network name. The default SSID is WNAP-7325 or WNAP-7335.
-30-
Site Survey
Enable Wireless
Disable SSID Broadcasting
Enable Isolated
Radio Mode
Channel
Data Rate
Security Setting
Transmit Power
Transmit Distance
TDMA
Advanced Settings
Access Control
User Manual of WNAP-7325/WNAP-7335
Click “ Site Survey ” to check the signal of remote sites.
Check it to enable Wireless function.
Check it to disable SSID broadcasting.
Check it to isolate each connected wireless client so that they cannot access each other.
Select the channel width to “ Auto Select ”, “ 5G 11NA HT20 ” or
“ 5G 11NA HT40 ”
Select the operating channel you would like to use. The channel range will be changed by selecting a different domain.
Select MCS0~15 or Auto from the pull-down menu. The default is
“ Auto ”.
Press “Setup” for more configurations. Please refer to 5.1.7
Security Setting for more information.
The range of transmit power is “ 12~27 dbm ”. In case of shortening the distance and the coverage of the wireless network, input a smaller value to reduce the radio transmission power.
Select a specified distance of the two nodes.
Displays the System Time.
Press “ Setup ” for more configurations. Please refer to 5.1.8
Advanced Settings for more information.
Press “ Setup ” for more configurations. Please refer to 5.1.9
Access Control for more information.
-31-
5.1.2 Client
User Manual of WNAP-7325/WNAP-7335
Click “ Operation Mode ” “ Client ” and the following page will be displayed. This section allows you to configure the Client mode.
Object
Regulatory Domain
Network SSID
Figure 5-4 Basic Settings - Client
Description
Select your domain from the list.
It is the wireless network name. The default SSID is
WNAP-7325 or WNAP-7335.
-32-
User Manual of WNAP-7325/WNAP-7335
Site Survey
Enable Wireless
Click “ Site Survey ” to find the remote sites to associate.
Check it to enable Wireless function.
Disable SSID Broadcasting Check it to disable SSID broadcasting.
Enable Isolated
Check it to isolate each connected wireless clients so that they cannot access each other.
Lock to AP MAC Enter the Mac address of the remote AP.
Radio Mode
Data Rate
Security Setting
Transmit Power
Select the channel width to “ Auto Select ”, “ 5G 11NA HT20 ” or
“ 5G 11NA HT40 ”
Select MCS0~15 or Auto from the pull-down menu. The default is “ Auto ”.
Press “ Setup ” for more configurations. Please refer to 5.1.7
Security Setting for more information.
The range of transmit power is “ 12~27 dbm ”. In case of shortening the distance and the coverage of the wireless network, input a smaller value to reduce the radio transmission power.
Transmit Distance Select a specified distance of the two nodes.
TDMA
Advanced Settings
Access Control
Displays the System Time.
Press “ Setup ” for more configurations. Please refer to 5.1.8
Advanced Settings for more information.
Press “ Setup ” for more configurations. Please refer to 5.1.9
Access Control for more information.
-33-
5.1.3 WDS AP
User Manual of WNAP-7325/WNAP-7335
Click “ Operation Mode ” “ WDS AP ” and the following page will be displayed. This section allows you to configure the WDS AP mode. For each wireless parameter, please refer to section 5.1.1 AP for more information.
Figure 5-5 Basic Settings – WDS AP
-34-
5.1.4 WDS Client
User Manual of WNAP-7325/WNAP-7335
Click “ Operation Mode ” “ WDS Client ” and the following page will be displayed. This section allows you to configure the WDS Client mode. For each wireless parameter, please refer to section 5.1.2 Client for more information.
Figure 5-6 Basic Settings – WDS Client
-35-
User Manual of WNAP-7325/WNAP-7335
5.1.5 AP Router
Click “ Operation Mode ” “ AP Router ” and the following page will be displayed. This section allows you to configure the AP Router mode.
Figure 5-7 Basic Settings – AP Router
-36-
5.1.6 Wireless ISP
User Manual of WNAP-7325/WNAP-7335
Click “ Operation Mode ” “ Wireless ISP ” and the following page will be displayed. This section allows you to configure the Wireless ISP mode.
-37-
User Manual of WNAP-7325/WNAP-7335
Figure 5-8 Basic Settings – WISP
5.1.7 Security Setting
Choose the operation mode you required, and then enter “ Security Setting ” by clicking the Setup button next to it and the following page will be displayed. This section allows you to configure the wireless security settings.
Object
Select Encryption
Figure 5-9 Security Settings
Description
Select the encryption that you need.
None: No security required
WEP: Input 5, 13 (ASCII) or 10, 26 (HEX) character for WEP key.
WPA: Enter ASCII characters between 8 and 63 character or 8 to 64 hexadecimal characters.
WPA2: Enter ASCII characters between 8 and 63 character or
8 to 64 hexadecimal characters.
WPA-Mixed: Enter ASCII characters between 8 and 63 character or 8 to 64 hexadecimal characters.
-38-
User Manual of WNAP-7325/WNAP-7335
None
Authentication is disabled and no password/key is required to connect to the access point.
WEP
WEP (Wired Equivalent Privacy) is a basic encryption. For a higher level of security consider using the WPA encryption.
Figure 5-10 Security Settings – WEP
Object
Authentication
Key Length
Key Format
Encryption Key
WPA
Description
You can select Open System , Shared Key or Auto .
Choose the WEP key length. You can choose 64-bit or 128-bit .
You can choose ASCII or Hex .
Enter the keys in the fields.
Figure 5-11 Security Settings – WPA Personal
-39-
User Manual of WNAP-7325/WNAP-7335
Figure 5-12 Security Settings – WPA Enterprise
Object
Pre-Authentication
Encryption Type
Description
Select “ Personal (Pre-Shared Key) ” or “ Enterprise (RADIUS) ” encryption type.
Set the WPA to be TKIP , AES or Auto .
Pre-Shared Key Enter the keys in the fields.
RADIU Server IP
Enter the RADIUS server host IP address.
Address
RADIU Server Port
Set the UDP port used in the authentication protocol of the RADIUS server. Value must be between 1 and 65535.
RADIU Server
Enter a shared secret/password between 1 and 99 characters in length.
Password
EAP
Reauthorization Set duration of session timeout in seconds between 300 and 3600.
Period
RSN
Enable or disable RSN reauthorization.
Reauthorization
WPA Group
Set duration of session timeout in seconds between 300 and 3600.
Re-key Interval
-40-
WPA2
Please refer to WPA for more information.
User Manual of WNAP-7325/WNAP-7335
Figure 5-13 Security Settings – WPA2 Personal
Figure 5-14 Security Settings – WPA2 Enterprise
-41-
WPA-Mixed
Please refer to WPA for more information.
User Manual of WNAP-7325/WNAP-7335
Figure 5-15 Security Settings – WPA-Mixed Personal
Figure 5-16 Security Settings – WPA-Mixed Enterprise
-42-
User Manual of WNAP-7325/WNAP-7335
5.1.8 Advanced Settings
Choose the operation mode you require, and then enter “ Advanced Settings ” by clicking the Setup button next to it and the following page will be displayed. This section allows you to configure the wireless advanced settings.
Object
RTS/CTS
Threshold
Beacon Interval
DTIM
Fragment Size
Figure 5-17 Advanced Settings
Description
When the length of a data packet exceeds this value, the router will send an RTS frame to the destination wireless node, and the latter will reply with a CTS frame, and thus they are ready to communicate. The default value is 2347.
Set beacon interval, the value range is from 20 to 999. The default value is 100.
Set the DTIM (delivery traffic indication message) period value of the wireless radio. The default value is 1.
A data packet that exceeds this value in length will be divided into multiple packets. The number of packets influences wireless network performance. Avoid setting this value low. Default at 2346.
-43-
Short GI
Aggregation
User Manual of WNAP-7325/WNAP-7335
Guard intervals are used to ensure that distinct transmissions do not interfere with one another. Only effect under Mixed Mode.
A part of the 802.11n standard that allows sending multiple frames per single access to the medium by combining frames together into one larger frame. It creates the larger frame by combining smaller frames with the same physical source, destination end points, and traffic class
(QoS) into one large frame with a common MAC header
Determines the number of frames combined in the new larger frame. Aggregated
Frames Number
Maximum
Aggregated Size
Determines the size (in bytes) of the larger frame.
Tx ChainMask
Rx ChainMask
WMM Capable
Displays the number of independent spatial data streams the device is transmitting (TX) and receiving (RX) simultaneously within one spectral channel of bandwidth. Multiple chains increase data transfer performance significantly.
Displays the number of independent spatial data streams the device is transmitting (TX) and receiving (RX) simultaneously within one spectral channel of bandwidth. Multiple chains increase data transfer performance significantly.
Wi-Fi Multimedia (WMM) is a Wi-Fi Alliance interoperability certification based on the IEEE 802.11e standard, which provides Quality of Service
(QoS) features to IEE 802.11 networks. WMM prioritizes traffic according to four categories: background, best effort, video and voice.
Figure 5-18 WMM Configuration
-44-
WMM Capable
BE
BK
VI
VO
Aifsn
CWMin
CWMax
Txop
User Manual of WNAP-7325/WNAP-7335
Traditional IP data, medium throughput and delay.
High throughput, non time sensitive bulk data e.g. FTP
Time sensitive video data with minimum time delay.
Time sensitive data such as VoIP and streaming media with minimum time delay.
Arbitration Inter-Frame Space (milliseconds): Specifies additional time between when a channel goes idle and the
AP/client sends data frames. Traffic with a lower AIFSN value has a higher priority.
Maximum Contention Window (milliseconds): This value is the upper limit to random backoff value doubling (see above).
Arbitration Inter-Frame Space (milliseconds): Specifies additional time between when a channel goes idle and the
AP/client sends data frames. Traffic with a lower AIFSN value has a higher priority.
Transmission Opportunity (milliseconds): The maximum interval of time an AP/client can transmit. This makes channel access more efficiently prioritized. A value of 0 means only one frame per transmission. A greater value effects higher priority.
-45-
User Manual of WNAP-7325/WNAP-7335
5.1.9 Access Control
Choose the operation mode you require, and then enter “ Access Control ” by clicking the Setup button next to it and the following page will be displayed. This section allows you to configure the wireless access control settings.
Object
Wireless Access
Control Mode
Mac Address
Comment
Figure 5-19 Access Control
Description
You can choose “ Disable ”, “ Allow Listed ” or “ Deny Listed ”.
The MAC address to be filtered.
Enter a comment of this setting.
-46-
User Manual of WNAP-7325/WNAP-7335
5.1.10 WAN Port Settings
Click “ Operation Mode ” “ AP Router ” or “ Wireless ISP ” and then enter the “ WAN Port Settings ” by clicking the Setup button next to it. This section allows you to configure the internet connection settings.
DHCP (Auto Config)
Choose “ DHCP ” and the router will automatically obtain IP addresses, subnet masks and gateway addresses from your ISP.
Figure 5-20 WAN Port Settings – DHCP
Static Mode (Fixed IP)
If your ISP offers you static IP Internet connection type, select “ Static Mode " and then enter IP address, subnet mask, primary DNS and secondary DNS information provided by your ISP in the corresponding fields.
Object
IP Address
Assigned by
Figure 5-21 WAN Port Settings – Static IP
Description
Enter the WAN IP address provided by your ISP. Enquire your ISP if you are not clear.
-47-
User Manual of WNAP-7325/WNAP-7335
Your ISP
IP Subnet Mask
ISP Gateway IP
Address
Primary DNS
Server
Secondary DNS
Server
PPPOE (ADSL)
Enter WAN Subnet Mask provided by your ISP.
Enter the necessary DNS address provided by your ISP. Default is
8.8.4.4.
Enter the other DNS address if your ISP provides you with 2 such addresses. Default is 8.8.8.8.
Enter the WAN Gateway address provided by your ISP.
Select PPPOE if your ISP is using a PPPoE connection and provide you with PPPoE user name and password info.
Object
User Name
Password
Verify Password
Figure 5-22 WAN Port Settings – PPPOE
Description
Enter the User Name provided by your ISP.
Enter the password provided by your ISP.
Enter the password again to verify if it is correct.
-48-
User Manual of WNAP-7325/WNAP-7335
5.1.11 Dynamic DNS Settings
Click “ Operation Mode ” “ AP Router ” or “ Wireless ISP ” and then enter the “ Dynamic DNS Settings ” by clicking the Setup button next to it. This section allows you to configure the DDNS settings.
Figure 5-23 Dynamic DNS Settings
Object
DDNS option
Description
Disable: Disable DDNS function
Enable Easy DDNS: Enable PLANET Easy DDNS
Enable Dynamic DDNS: You are allowed to modify the DDNS settings.
Dynamic DNS Provider Select a server provider or disable the existing server.
Account
Password
Enter the DDNS user name of the DDNS account.
DDNS
Enter the DDNS password of the DDNS account.
Enter the host name or domain name provided by DDNS provider.
Example of Planet DDNS Settings:
Please go to http://www.planetddns.com/ to register a Planet DDNS account.
Please refer to the FAQ ( http://www.planetddns.com/index.php/faq ) for how to register a free account.
-49-
User Manual of WNAP-7325/WNAP-7335
Click “ Operation Mode ” “ AP Router ” or “ Wireless ISP ”, select Dynamic DNS Settings and press “ Setup ”.
Step 1. Select “ Enable Dynamic DDNS ” and “ PlanetDDNS.com
” from the list of Dynamic DNS Provider to use the Planet DDNS service.
Step 2. Configure the DDNS account that has been registered in Planet DDNS website.
Account: Enter your DDNS host (format: xxx.planetddns.com
, xxx is the registered domain name)
Password: Enter the password of your account.
DDNS: Enter your DDNS host again.
-50-
User Manual of WNAP-7325/WNAP-7335
Step 3. Go to “ Remote Management ” to enable remote access from WAN port.
Step 4. Go to “ WAN Port Settings ” to configure WAN connection to Static Mode (fixed IP).
Step 5. Save the setting and connect your WAN port of the Wireless AP to the internet via Ethernet cable.
In a remote computer, enter the DDNS host name as the figure shown below. Then, you should be able to login the WNAP-7325 remotely.
Example of Easy DDNS Settings:
This service is not required to register any DDNS account.
-51-
User Manual of WNAP-7325/WNAP-7335
Please refer to the procedure listed as follows to configure using Planet Easy DDNS service.
Step 1. Select “ Enable Easy DDNS ” to use the Planet Easy DDNS service.
Easy Domain Name: Display the specified domain name for this device.
(Format: ptxxxxxx.planetddns.com
, xxxxxx is the last six-digit of the WAN Port MAC address)
Step 2. Go to “ Remote Management ” to enable remote access from WAN port.
Step 3. Go to “ WAN Port Settings ” to configure WAN connection to Static Mode (fixed IP).
-52-
User Manual of WNAP-7325/WNAP-7335
Step 6. Save the setting and connect your WAN port of the Wireless AP to the internet via Ethernet cable.
In a remote computer, enter the Easy Domain Name displayed in Step 1
. Then, you should be able to login the
WNAP-7325 remotely.
5.1.12 Remote Management
Click “ Operation Mode ” “ AP Router ” or “ Wireless ISP ” and then enter the “ Remote Management ” by clicking the Setup button next to it. This section allows you to enable or disable the remote management through the WAN port.
Figure 5-24 Remote Management
Object
Remote management
(via WAN)
Ping from WAN
Description
Enable or Disable this function.
Enable or Disable this function.
-53-
User Manual of WNAP-7325/WNAP-7335
5.1.13 DHCP Server Settings
Click “ Operation Mode ” “ AP Router ” or “ Wireless ISP ” and then enter the “ DHCP Server Settings ” by clicking the Setup button next to it. This section allows you to configure the DHCP server.
Figure 5-25 DHCP Server Settings
Object
DHCP Server
Lease Time
From
To
Description
Select as DHCP server or disable the function.
Select the time for using one assigned IP from the dropdown list. After the lease time, the AP automatically assigns new IP addresses to all connected computers.
The start IP address of all the available successive IPs.
The end IP address of all the available successive IPs.
5.1.14 DMZ Settings
Click “ Operation Mode ” “ AP Router ” or “ Wireless ISP ” and then enter the “ DMZ Settings ” by clicking the
Setup button next to it. This section allows you to configure the DMZ server.
Figure 5-26 DMZ Settings
-54-
User Manual of WNAP-7325/WNAP-7335
Object
DMZ Setting
DMZ IP Address
Description
Disable or Enable DMZ function.
Enter the DMZ IP address.
5.1.15 Virtual Server Settings
Click “ Operation Mode ” “ AP Router ” or “ Wireless ISP ” and then enter the “ Virtual Server Settings ” by clicking the Setup button next to it. This section allows you to configure the virtual server.
Object
Virtual Server
Protocol
IP Address
Port Range
Comment
Figure 5-27 Virtual Server Settings
Description
Enable or disable Virtual Server.
You can choose TCP, UDP or Both.
Enter the LAN IP.
Set the range of public port.
Set a name for the rule.
5.1.16 IP Filtering Settings
Click “ Operation Mode ” “ AP Router ” or “ Wireless ISP ” and then enter the “ IP Filtering Settings ” by clicking the Setup button next to it. This section allows you to configure the IP filtering settings.
-55-
User Manual of WNAP-7325/WNAP-7335
Figure 5-28 IP Filtering Settings
Object
Filtering
Protocol
IP Address
Comment
5.1.17 Port Filtering Settings
Description
Enable or disable IP Filtering.
You can choose TCP, UDP or Both.
Enter the IP address to be filtered.
Set a name for the rule.
Click “ Operation Mode ” “ AP Router ” or “ Wireless ISP ” and then enter the “ Port Filtering Settings ” by clicking the Setup button next to it. This section allows you to configure the port filtering settings.
Object
Filtering
Protocol
Port Range
Comment
Figure 5-29 Port Filtering Settings
Description
Enable or disable IP Filtering.
You can choose TCP, UDP or Both.
Enter the range of Port to be filtered.
Set a name for the rule.
-56-
User Manual of WNAP-7325/WNAP-7335
5.1.18 MAC Filtering Settings
Click “ Operation Mode ” “ AP Router ” or “ Wireless ISP ” and then enter the “ Mac Filtering Settings ” by clicking the Setup button next to it. This section allows you to configure the MAC filtering settings.
Figure 5-30 Mac Filtering Settings
Object
Filtering
Mac Address
Comment
5.1.19 Bandwidth Control
Description
Enable or disable Mac Filtering.
Enter the Mac address to be filtered.
Set a name for the rule.
Click “ Operation Mode ” “ AP Router ” or “ Wireless ISP ” and then enter the “ Bandwidth Control ” by clicking the Setup button next to it. This section allows you to configure the bandwidth control.
Object
Quality of
Figure 5-31 Bandwidth Control Settings
Description
Enable or disable the QoS service.
-57-
User Manual of WNAP-7325/WNAP-7335
Service
Type Select QoS type IP Address or Mac Address .
Local IP Address The IP address segment which uses this QoS rule.
MAC Address The Mac address which uses this QoS rule.
Uplink BandWidth
Set the maximum uplink bandwidth allowed by the listed QoS rules.
(Kbps)
Downlink
BandWidth (Kbps)
Set the maximum downlink bandwidth allowed by the listed QoS rules.
Comment Set a name for the rule.
5.1.20 SNMP
Click “ Operation Mode ” “ AP Router ” or “ Wireless ISP ” and then enter the “ SNMP ” by clicking the Setup button next to it. This section allows you to configure the SNMP.
Figure 5-32 SNMP Settings
Object
SNMP
Read Community
Write Community
Trap IP 1
Trap Community
Description
Enable or disable the SNMP service.
Enter a Read Community name for verification with the SNMP manager for SNMP Read requests.
Enter a Write Community name for verification with the SNMP manager for SNMP Write requests.
Enter the Trap IP address.
Enter an SNMP Trap Community name for verification with the SNMP manager for SNMP Trap requests.
-58-
User Manual of WNAP-7325/WNAP-7335
5.2 System Configuration
On this page, you can configure the system of the AP, including IP settings, Time settings, Password settings,
System management, Ping Watchdog, Firmware upgrade, Configuration save and restore, Factory default,
Reboot and Schedule reboot.
Figure 5-33 System Configuration default page
5.2.1 Default IP Settings
Click “ System Configuration ” “ Device IP Settings ” and the following page will be displayed.
Figure 5-34 Default IP Settings
-59-
User Manual of WNAP-7325/WNAP-7335
The page includes the following fields:
Object
IP Address
IP Subnet Mask
Gateway IP Address
Primary DNS Server
Secondary DNS Server
Description
Access Point’s LAN IP.
The default is 192.168.1.253
. You can change it according to your needs.
Access Point’s LAN subnet mask.
The Gateway IP address of Access Point.
Enter the DNS server. The default is 8.8.4.4.
Enter the DNS server. The default is 8.8.8.8.
5.2.2 Time Settings
Click “ System Configuration ” “ Time Settings ” and the following page will be displayed.
Figure 5-35 Time Settings
Object
Enable NTP
Description
Enable it to support NTP (Network Time Protocol) for automatic time and date setup.
Server Name Enter the host name or IP address of the time server if you wish.
NTP Request Interval Specify a frequency (in hours) for the access point to update/synchronize with the NTP server.
Local Time Zone Select the time zone of your country/region. If your country/region is not listed, please select another country/region whose time zone is the same as yours.
Local Date and Time Set the access point’s date and time manually.
-60-
User Manual of WNAP-7325/WNAP-7335
5.2.3 Password Settings
Click “ System Configuration ” “ Password Settings ” and the following page will be displayed.
Figure 5-36 Password Settings
Object
Current Password
New Password
Re-enter New
Password
Description
Set the access point’s administrator password. This is used to log in to the browser based on the configuration interface.
Enter a new password.
Enter the new password again.
5.2.4 System Management
Click “ System Configuration ” “ System Management ” and the following page will be displayed.
-61-
User Manual of WNAP-7325/WNAP-7335
Figure 5-37 System Management
Object
Device Name
POE Passthrough
UPnP
Syslog
IGMP
Description
Enter a name for this access point. Default is WNAP-7325 or
WNAP-7335 .
Enable the POE Passthrough function.
※ When the option “ Enable POE Passthrough ” in the System
Management page is checked, the LAN2 can supply passive PoE power to the second WNAP-7325 or WNAP-7335 through the LAN 2.
Check to enable the UPnP function.
The UPnP feature allows the devices, such as Internet computers, to access the local host resources or devices as needed. UPnP devices can be automatically discovered by the UPnP service application on the LAN. This option is only available in AP
Router mode.
Check to enable Syslog function.
Check to enable the IGMP Proxy function.
This option is only available in AP Router mode.
5.2.5 Ping Watchdog
Click “ System Configuration ” “ Ping Watchdog ” and the following page will be displayed.
-62-
User Manual of WNAP-7325/WNAP-7335
Figure 5-38 Ping Watchdog
Object
Ping Watchdog
IP Address 1
Ping Frequency
Failed tries
Action
Description
Enable or Disable this function.
Enter the IP address which pings every time interval
Set times from 10 to 999.
Select failed tries from 1 to 5.
System will reboot when failing to ping the IP.
5.2.6 Firmware Upgrade
Click “ System Configuration ” “ Firmware Upgrade ” and the following page will be displayed.
Figure 5-39 Firmware Upgrade
-63-
Object
Browse
User Manual of WNAP-7325/WNAP-7335
Description
Click Browse to select the firmware file and click Upgrade to upgrade the firmware.
5.2.7 Configuration Save and Restore
Click “ System Configuration ” “ Configuration Save and Restore ” and the following page will be displayed.
Figure 5-40 Configuration Save and Restore
Object
SAVE
Browse
Description
Click SAVE to save the configuration to a management host.
Click Browse to select the configuration file and click Restore to restore the configuration file.
5.2.8 Factory Default
Click “ System Configuration ” “ Factory Default ” and the following page will be displayed.
Press YES to restore to factory default.
Figure 5-41 Factory Default
-64-
User Manual of WNAP-7325/WNAP-7335
5.2.9 Reboot System
Click “ System Configuration ” “ Reboot System ” and the following page will be displayed.
Press YES to reboot the system.
Figure 5-42 Reboot System
5.2.10 Schedule Reboot
Click “ System Configuration ” “ Schedule Reboot ” and the following page will be displayed.
This page allows you to enable and configure system reboot schedule. The device can regularly reboot according to the reserved time when connecting to the Internet.
Figure 5-43 Schedule Reboot
-65-
User Manual of WNAP-7325/WNAP-7335
Object
Schedule Reboot
Reboot Time
Reboot Plane
Weekday
Description
Enable or Disable this function.
Enter the time that you want to reboot this device.
Select Weekday to reboot in the day you choose or Every day .
Select the day that you want to reboot.
1. This setting will only take effect when the Internet connection is accessible and the GMT time is configured correctly.
2. You must select at least one day when choosing “ Weekday ” as your reboot plan.
3. When choosing “ Every day ” as your reboot plan, the “ Weekday ” will be grayed out
(disabled), which means Every day will auto reboot at the time that you schedule.
Example of how to configure Schedule Reboot . Please take the following steps:
Before configuring schedule reboots, please ensure the Internet connection is accessible and the GMT time is configured correctly according to NTP Settings page.
Step 1. Enable the “Schedule Reboot”.
Step 2. Enter the Reboot Time (24-hour format) to enable this function to take effect. For example, if you want this function to work at 23:00 every Sunday, choose "Weekday" in the Reboot Plan field.
Figure 5-44 Schedule Reboot - Example
Step 3. Click the “Apply Changes” button to take this function effect.
-66-
User Manual of WNAP-7325/WNAP-7335
5.3 Tools
5.3.1 Network Ping
Click “ Tools ” “ Network Ping ” and the following page will be displayed.
Ping is a network tool used to test whether a particular host is reachable across an IP network.
Enter the IP, Ping Count, and click “ Ping ” to diagnostic your internet connection.
Figure 5-45 Network Ping
5.3.2 Network Traceroute
Click “ Tools ” “ Network Traceroute ” and the following page will be displayed.
Traceroute is a computer network diagnostic tool for displaying the route (path) and measuring transit delays of packets across an Internet Protocol (IP) network. It can help identify connection problems.
Enter the IP and click “ Traceroute ” to diagnostic your internet connection.
-67-
User Manual of WNAP-7325/WNAP-7335
Figure 5-46 Network Traceroute
-68-
5.4 Device Status
User Manual of WNAP-7325/WNAP-7335
Figure 5-47 Device Status
-69-
User Manual of WNAP-7325/WNAP-7335
5.4.1 Device Information
Click “ Device Status ” “ Device Information ” and the following page will be displayed.
The page includes the following fields:
Figure 5-48 Device Information
Object
Firmware Version
Device IP
Device MAC
Gateway IP
DNS IP
Wireless MAC
Uptime
CPU Loading
Description
Displays current F/W version.
Displays IP of AP.
Displays AP’s LAN MAC address.
Displays Gateway IP of AP.
Displays DNS IP of AP.
Displays AP’s Wireless MAC address.
Displays the uptime of AP.
Displays the CPU loading of AP.
-70-
User Manual of WNAP-7325/WNAP-7335
5.4.2 Wireless Information
Click “ Device Status ” “ Wireless Information ” and the following page will be displayed.
The page includes the following fields:
Figure 5-49 Wireless Information
Object
Operation Mode
Physical address
SSID
Band
Radio Channel
Wireless Encryption
Transmit Power
Description
Displays current Operation Mode.
Displays AP’s Wireless MAC address.
It is the wireless network name. The default SSID is
WNAP-7325 or WNAP-7335 .
Displays operating channel width which is Auto Select , 5G
11NA HT20 or 5G 11NA HT40 .
Displays the channel you would like to use. The channel range will be changed by selecting a different domain.
Displays the encryption type that you would like to use.
Display the TX power that you would like to use.
-71-
User Manual of WNAP-7325/WNAP-7335
5.4.3 LAN Information
Click “ Device Status ” “ LAN Information ” and the following page will be displayed.
Figure 5-50 LAN Information
The page includes the following fields:
Object
Physical Address
Description
Displays AP’s LAN MAC address.
IP Address Displays IP of AP.
Network Mask
Default Gateway
Displays Network Mask of AP.
Displays Gateway IP of AP.
DHCP Start IP Address
DHCP Server
DHCP Finish IP
Address
Enable or Disable DHCP server.
Enter the starting IP address for the DHCP server’s IP assignment.
Enter the ending IP address for the DHCP server’s IP assignment.
-72-
User Manual of WNAP-7325/WNAP-7335
5.4.4 Wireless Client Table
Click “ Device Status ” “ Wireless Client Table ” and the following page will be displayed.
The page includes the following fields:
Figure 5-51 Wireless Client Table
Object
No.
Description
Displays the number of connecting device.
Mac Address
Connection Speed
Displays Mac address of AP.
Signal Strength
Displays connection speed of device.
Display signal strength of device.
The signal strength between “ -30 and -70 ” can set up a reliable connection.
-73-
User Manual of WNAP-7325/WNAP-7335
5.4.5 System Log
Choose menu “ Device Status “ System Log ” to view the logs of the Wireless AP.
5.5 Logout
Select “ Logout ” to logout the system.
Figure 5-52 System Log
Figure 5-53 Logout
-74-
User Manual of WNAP-7325/WNAP-7335
Figure 5-54 Re-login
-75-
User Manual of WNAP-7325/WNAP-7335
Appendix A: Troubleshooting
If you found the AP is working improperly or stop responding to you, please read this troubleshooting first before contacting the Planet Tech Support for help. Some problems can be solved by yourself within very short time.
Scenario Solution
The AP is not responding to me when a. Please check the connection of the power cord and the
Ethernet cable of this AP. All cords and cables should be
I want to access it by web browser. correctly and firmly inserted to the AP. b. If all LEDs on this AP are off, please check the status of power adapter, and make sure it is correctly powered. c. You must use the same IP address section that AP uses.
d. Are you using MAC or IP address filter? Try to connect the AP by another computer and see if it works; if not, please reset the AP to the factory default settings (Press the ‘reset’ button for over 10 seconds). e. Set your computer to static IP address, and see if the
Planet Smart Discovery can find the AP or not. f. If you did a firmware upgrade and this happens, contact the Planet Tech Support for help. g. If all the solutions above don’t work, contact the Planet
Tech Support for help.
I can’t get connected to the Internet. a. Check the Internet connection status from the router that is connected with the AP. b. Please be patient. Sometimes, Internet is just that slow. c. If you have connected a computer to Internet directly before, try to do that again, and check if you can get connected to Internet with your computer directly attached to the device provided by your Internet service provider. d. Check PPPoE / L2TP / PPTP user ID and password in your router again. e. Call your Internet service provider and check if there’s something wrong with their service. f. If you just can’t connect to one or more website, but you can still use other internet services, please check
URL/Keyword filter. g. Try to reset the AP and try again later. h. Reset the device provided by your Internet service provider. i. Try to use IP address instead of hostname. If you can use IP address to communicate with a remote server, but can’t use hostname, please check DNS setting.
I can’t locate my AP by my wireless a. ‘Broadcast ESSID’ set to off?
-76-
User Manual of WNAP-7325/WNAP-7335 device. b. The antenna is properly secured. c. Are you too far from your AP? Try to get closer. d. Please remember that you have to input ESSID on your wireless client manually, if ESSID broadcast is disabled.
File downloading is very slow or a. Are you using QoS function? Try to disable it and try breaks frequently. again. b. Internet is slow sometimes; try to be patient. c. Try to reset the AP and see if it’s better after that. d. Try to know what computers do on your local network. If someone’s transferring big files, other people will think
Internet is really slow. e. If this never happens before, call you Internet service provider to know if there is something wrong with their network.
I can’t log into the web management interface; The password is wrong.
The AP becomes hot a. Make sure you’re connecting to the correct IP address of the AP. b. Password is case-sensitive. Make sure the ‘Caps Lock’ light is not illuminated. c. If you really forget the password, do a hardware reset. a. This is not a malfunction, if you can keep your hand on the AP’s case. b. If you smell something wrong or see the smoke coming out from AP or A/C power adapter, please disconnect the AP and A/C power adapter from utility power (make sure it’s safe before you’re doing this!), and call your dealer for help.
-77-
User Manual of WNAP-7325/WNAP-7335
Appendix B: Use Planet Smart Discovery to find AP
To easily discover the WNAP-7325 in your Ethernet environment, the Planet Smart Discovery Utility from user’s manual CD-ROM is an ideal solution.
The following install instructions will guide you to running the Planet Smart Discovery Utility.
Step 1 : Deposit the Planet Smart Discovery Utility in administrator PC.
Step 2 : Execute this utility.
Step 3 : Click the “Refresh” button as shown below to update the list of the currently connected devices.
Figure C-1
Step 3 : Select the WNAP-7325 from the list and then click the “Connect to Device” button to login to the Web
Management Configuration Page.
The fields in white background can be modified directly, and then you can apply the new setting by clicking the “ Update Device ” button.
-78-
User Manual of WNAP-7325/WNAP-7335
Appendix C: FAQ
Q1: How to set up the AP Client Connection
Topology:
Step 1 . Use static IP in the PCs that are connected with AP-1(Site-1) and AP-2(Site-2). In this case, Site-1 is
“ 192.168.1.100
”, and Site-2 is “ 192.168.1.200
”.
-79-
User Manual of WNAP-7325/WNAP-7335
Step 2 . In AP-1, go to “ Operation Mode ” to configure it to Access Point Mode.
※ You can also configure it in “AP Router” mode if you want to connect the WAN port of the AP to the internet directly.
Step 3 . Click “ Setup ” to configure the following parameters and then click Save & Restart to save the settings.
1) Network ID (SSID) : set to a unique value
2) Channel : set to a fixed one
3) Security Setting : strongly suggested to configure it.
In this case, we configure it to WPA2-PSK, AES
-80-
User Manual of WNAP-7325/WNAP-7335
-81-
User Manual of WNAP-7325/WNAP-7335
Step 4 . In AP-2, modify the default IP to the same IP range but different from AP-1.
In this case, the IP is changed to 192.168.1.252
.
Step 5 . In AP-2, configure it in “ Client ” mode and click “ Setup ”.
-82-
User Manual of WNAP-7325/WNAP-7335
Step 6 . Click “ Setup ” and then click Site Survey to find the AP-1.
Step 7 . Select the AP-1 from the list.
-83-
User Manual of WNAP-7325/WNAP-7335
Step 8 . Click “ SET SECURITY ” to configure the Pre-Shared Key and then click “ Save ” to close the window.
Step 9 . Click “OK” and “ Save & Restart ” to apply the setting.
-84-
User Manual of WNAP-7325/WNAP-7335
Step 10 . In AP-1, go to “ Device Status-> Wireless Client Table ” to check whether AP-2 should be in the list.
Step 11 . Use command line tool to ping each other to ensure the link is successfully established.
From Site-1, ping 192.168.1.200; and in Site-2, ping 192.168.1.100.
Step 12 . Configure the TCP/IP settings of Site-2 to “ Obtain an IP address automatically ”.
-85-
User Manual of WNAP-7325/WNAP-7335
Step 13 . Use command line tool to ping the DNS (e.g., Google) to ensure Site-2 can access internet through the wireless connection.
The attention of the following hints should be paid:
1) The encryption method must be the same as that of both sites if configured.
2) Both sites should be Line-of-Sight.
3) For the short distance connection less than 1km, please reduce the "Transmit power" of both sites.
4) For the long distance connection over 1km, please adjust the "Transmit Distance" to the actual distance or double of the actual distance.
-86-
Q2: How to set up the WDS Connection
Topology:
User Manual of WNAP-7325/WNAP-7335
Step 1 . Use static IP in the PCs that are connected with WNAP-7350-1 (Site-1) and WNAP-7350-2 (Site-2). In this case, Site-1 is “ 192.168.1.100
”, and Site-2 is “ 192.168.1.200
”.
-87-
User Manual of WNAP-7325/WNAP-7335
Step 2 . In AP-1, go to “ Operation Mode ” to configure it in Access Point Mode.
Step 3 . Click “ Setup ” to configure the following parameters and then click Save & Restart to save the settings.
4) Network ID (SSID) : set to a unique value
5) Channel : set to a fixed one
6) Security Setting : strongly suggested to configure it.
In this case, we configure it to WPA2-PSK, AES
-88-
User Manual of WNAP-7325/WNAP-7335
Step 4 . In AP-2, modify the default IP to the same IP range but different from AP-1.
In this case, the IP is changed to 192.168.1.252
.
Step 5 . In AP-2, configure it in “ Client ” mode and click “ Setup ”.
-89-
Step 6 . Click “ Setup ” and then click Site Survey to find AP-1.
User Manual of WNAP-7325/WNAP-7335
Step 7 . Select AP-1 from the list.
-90-
User Manual of WNAP-7325/WNAP-7335
Step 8 . Click “ SET SECURITY ” to configure the Pre-Shared Key and then click “ Save ” to close the window.
Step 9 . Click “OK” and click “ Save & Restart ” to apply the setting.
Step 10 . In AP-1, go to “ Device Status-> Wireless Client Table ” to check whether AP-2 should be in the list.
Step 11 . Use command line tool to ping each other to ensure the link is successfully established.
From Site-1, ping 192.168.1.200; and in Site-2, ping 192.168.1.100.
-91-
User Manual of WNAP-7325/WNAP-7335
The attention of the following hints should be paid:
1) The encryption method must be the same as that of both sites if configured.
2) Both sites should be Line-of-Sight.
3) For the short distance connection less than 1km, please reduce the "Transmit power" of both sites.
4) For the long distance connection over 1km, please adjust the "Transmit Distance" to the actual distance or double of the actual distance.
-92-
EC Declaration of Conformity
For the following equipment:
*Type of Product :
5GHz 802.11a/n 300Mbps Wireless LAN Outdoor CPE
*Model Number :
WNAP-7325 / WNAP-7335
* Produced by:
Manufacturer’s Name : Planet Technology Corp.
Manufacturer’s Address: 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.) is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to
1999/5/EC R&TTE,
Low Voltage
Directive 2006/95/EC
.
For the evaluation regarding the R&TTE the following standards were applied:
EN 301 893 V1.7.1
EN 301 489-1 V1.9.2
EN 301 489-17 V2.2.1
(2011-06)
(20
11
)
(20
1
2)
EN 62311 (20
08
)
EN 60950-1 (2006 + A11: 2009 + A1:2010 +
A12:2011+A2:2013)
Responsible for marking this declaration if the:
Manufacturer
Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Product Manager
Taiwan
Place
8
th
Jan., 2015
Date Legal Signature
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528
English
Č esky
Dansk
EC Declaration of Conformity
Hereby, PLANET Technology Corporation, declares that this 300Mbps 802.11a/n Wireless
Outdoor CPE is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Spole č nost PLANET Technology Corporation, tímto prohlašuje, že tato 300Mbps 802.11a/n
Wireless Outdoor CPE spl ň uje základní požadavky a další p ř íslušná ustanovení sm ě rnice
1999/5/EC.
PLANET Technology Corporation, erklærer herved, at følgende udstyr 300Mbps 802.11a/n
Wireless Outdoor CPE overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF
Lietuviškai
Magyar
Malti
Šiuo PLANET Technology Corporation, , skelbia, kad 300Mbps 802.11a/n Wireless Outdoor CPE tenkina visus svarbiausius 1999/5/EC direktyvos reikalavimus ir kitas svarbias nuostatas.
A gyártó PLANET Technology Corporation , kijelenti, hogy ez a 300Mbps 802.11a/n Wireless Outdoor
CPE megfelel az 1999/5/EK irányelv alapkövetelményeinek és a kapcsolódó rendelkezéseknek.
Hawnhekk, PLANET Technology Corporation, jiddikjara li dan 300Mbps 802.11a/n Wireless
Outdoor CPE jikkonforma malħ ti ġ ijiet essenzjali u ma provvedimenti o ħ rajn relevanti li hemm fid-Dirrettiva 1999/5/EC
Hierbij verklaart , PLANET Technology orporation, dat 300Mbps 802.11a/n Wireless Outdoor CPE in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG
Deutsch
Eestikeeles
Ελληνικά
Español
Français
Italiano
Latviski
Hiermit erklärt PLANET Technology Corporation, dass sich dieses Gerät 300Mbps 802.11a/n
Wireless Outdoor CPE in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten
Vorschriften der Richtlinie 1999/5/EG befindet".
(BMWi)
Käesolevaga kinnitab PLANET Technology
Corporation, et see 300Mbps 802.11a/n Wireless
Outdoor CPE vastab Euroopa Nõukogu direktiivi
1999/5/EC põhinõuetele ja muudele olulistele tingimustele.
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ , PLANET Technology
Corporation, ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ 300Mbps
802.11a/n Wireless Outdoor
CPE ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ
ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ ΕΚ
Por medio de la presente, PLANET Technology
Corporation, declara que 300Mbps 802.11a/n
Wireless Outdoor CPE cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE
Par la présente, PLANET Technology
Corporation, déclare que les appareils du
300Mbps 802.11a/n Wireless Outdoor CPE sont conformes aux exigences essentielles et aux autres dispositions pertinentes de la directive
1999/5/CE
Con la presente , PLANET Technology
Corporation, dichiara che questo 300Mbps
802.11a/n Wireless Outdoor CPE è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva
1999/5/CE.
Ar šo PLANET Technology Corporation, apliecina, ka š ī 300Mbps 802.11a/n Wireless
Outdoor CPE atbilst Direkt ī vas 1999/5/EK pamatpras ī b ā m un citiem atbilstošiem noteikumiem.
Nederlands
Polski
Português
Slovensky
Slovensko
Suomi
Svenska
Niniejszym firma PLANET Technology Corporation, o ś wiadcza, ż e 300Mbps 802.11a/n Wireless
Outdoor CPE spe ł nia wszystkie istotne wymogi i klauzule zawarte w dokumencie „Directive
1999/5/EC”.
PLANET Technology Corporation , declara que este
300Mbps 802.11a/n Wireless Outdoor CPE está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.
Výrobca PLANET Technology Corporation, týmto deklaruje, že táto 300Mbps 802.11a/n Wireless
Outdoor CPE je v súlade so základnými požiadavkami a ď alšími relevantnými predpismi smernice 1999/5/EC.
PLANET Technology Corporation , s tem potrjuje, da je ta 300Mbps 802.11a/n Wireless Outdoor CPE skladen/a z osnovnimi zahtevami in ustreznimi dolo č ili
Direktive 1999/5/EC.
PLANET Technology Corporation, vakuuttaa täten että 300Mbps 802.11a/n Wireless Outdoor CPE tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Härmed intygar, PLANET Technology Corporation, att denna 300Mbps 802.11a/n Wireless Outdoor
CPE står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Advertisement
