Advertisement
Advertisement
Video Intercom Module Door Station
User Manual
Video Intercom Module Door Station · User Manual
User Manual
© 2018 Hangzhou Hikvision Digital Technology Co., Ltd.
This user manual is intended for users of module door station.
The door station supports custom combination. You can choose from the modules listed below according to needs.
Name Model
Main Unit DS-KD8003-IME1
Nametag Module
Keypad Module
Card Reader Module
DS-KD-KK
DS-KD-KP
DS-KD-M(13.56 MHz)
DS-KD-E(125 KHz)
Indicator Module
Blank Module
DS-KD-IN
DS-KD-BK
It includes instructions on how to use the Product. The software embodied in the
Product is governed by the user license agreement covering that Product.
About this Manual
This Manual is subject to domestic and international copyright protection. Hangzhou
Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to this manual. This manual cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and are registered trademarks or the subject of applications for the same by Hikvision and/or its affiliates. Other trademarks mentioned in this manual are the properties of their respective owners. No right of license is given to use such trademarks without express permission.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, REGARDING THIS MANUAL.
HIKVISION DOES NOT WARRANT, GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE
USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION
CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE
WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY. ii
Video Intercom Module Door Station · User Manual
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HIKVISION, ITS
DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES
FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS OF DATA
OR DOCUMENTATION, IN CONNECTION WITH THE USE OF OR RELIANCE ON THIS MANUAL, EVEN IF
HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY OR CERTAIN
DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.
Support
Should you have any questions, please do not hesitate to contact your local dealer. iii
Video Intercom Module Door Station · User Manual
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—
Reorient or relocate the receiving antenna.
—
Increase the separation between the equipment and receiver.
—
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—
Consult the dealer or an experienced radio/TV technician for help.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive
2014/30/EU, LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info iv
Video Intercom Module Door Station · User Manual
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery information.
The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point.
For more information see: www.recyclethis.info v
Video Intercom Module Door Station · User Manual
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings Follow these safeguards to prevent serious injury or death.
Cautions Follow these precautions to prevent potential injury or material damage.
Warnings
The working temperature of the device is from -40 º to 60 C .
All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region.
Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.
Please make sure that the power has been disconnected before you wire, install or dismantle the device.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)
The power supply must conform to LPS. The recommended adaptor models and manufacturers are shown as below. Use the attached adaptor, and do not change the adaptor randomly.
Model
ADS-24S-12 1224GPCN
KPL-060F-VI
Manufacturer
Shenzhen Honor Electronic
Co., Ltd.
Channel Well Technology
Co., Ltd.
Standard
GB
GB vi
Video Intercom Module Door Station · User Manual
Cautions
Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation.
Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.
Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents.
Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper.
Transportation without the original wrapper may result in damage on the device and lead to additional costs.
Improper use or replacement of the battery may result in hazard of explosion.
Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.
The warranty does not apply to the product defects and failures arisen as a result of improper mounting (in contradiction herewith).
When the proper mounting instructions are not met, water might get in and destroy the electronics. vii
Video Intercom Module Door Station · User Manual
Table of Contents
4.5.1 More-than-Three Module Surface Mounting .................................................. 44
4.5.2 More-than-Three Module Flush Mounting ..................................................... 50
viii
Video Intercom Module Door Station · User Manual
ix
Video Intercom Module Door Station · User Manual
1 Overview
1.1
Introduction
The video intercom module door station can realize functions such as video intercom, resident-to-resident video call to provide a complete smart community video intercom solution.
The video intercom module door station is mainly applied to situations such as community, villa, and official buildings.
1.2
Main Features
2MP HD video intercom function
Access control function
Fisheye camera with IR supplement light
Tampering alarm and door magnetic alarm supported
Supports sub-modules’ access (max.8)
Noise suppression and echo cancellation
Easy to extend
1
Video Intercom Module Door Station · User Manual
1.3
Typical Application
Figure 1-1 Typical Application
2
Video Intercom Module Door Station · User Manual
2 Appearance
2.1
Main Unit
Figure 2-1 Main Unit Appearance
8
9
10
6
7
4
5
No.
1
2
3
Table 2-1 Appearance Description
Description
Microphone
Low Illumination IR Supplement Light
Built-in Camera
Loudspeaker
Call Button
Nametag
TAMPER
Network Interface
Module-connecting Interface(output)
Terminals
Nametag area supports insert customized name card.
The suggested card size is: 58 (L) x 11.7(W) mm.
3
Video Intercom Module Door Station · User Manual
2.2
Nametag Module
Figure 2-2 Nametag Module Appearance
No.
1
4
5
2
3
Table 2-2 Appearance Description
Description
Call Button
Nametag
Module-connecting Interface(output)
Module-connecting Interface(input)
Debug Port
Nametag area supports insert customized name card.
The suggested card size is: 58 (L) x 11.7(W) mm.
4
Video Intercom Module Door Station · User Manual
2.3
Keypad Module
Figure 2-3 Keypad Module Appearance
No.
1
2
3
4
Table 2-3 Appearance Description
Description
Button
Module-connecting Interface(output)
Module-connecting Interface(input)
Debug Port
2.4
Indicator Module
Figure 2-4 Keypad Module Appearance
5
No.
1
2
3
4
5
6
Video Intercom Module Door Station · User Manual
Table 2-4 Appearance Description
Description
Calling Indicator
Two-way Audio Indicator
Unlock Indicator
Module-connecting Interface(output)
Module-connecting Interface(input)
Debug Port
The indicator’s status description is listed as below:
Indicator
Calling
Indicator
Two-way
Audio
Indicator
Unlock
Indicator
Table 2-5 Indicator Status Description
Status
Solid Yellow
Unlit
Solid White
Unlit
Description
Calling
Off-calling
Two-way audio
Off-two-way audio
Solid blue
Unlit
Opening Door
Door is locked.
2.5
Card Reader Module
Figure 2-5 Card Reader Module Appearance
6
Video Intercom Module Door Station · User Manual
No.
1
2
3
4
Table 2-6 Appearance Description
Description
Card Reading Area
Module-connecting Interface(output)
Module-connecting Interface(input)
Debug Port
2.6
Blank Module
Blank module is designed to the fill blank grid during installation. You can replace it with other module when you needed.
Figure 2-6 Blank Module Appearance
7
Video Intercom Module Door Station · User Manual
3 Terminal and Wiring
3.1
Terminal Description
3.1.1
Main Unit
No.
A5
A6
A7
A8
A1
A2
A3
A4
B1
B2
B3
B4
Figure 3-1 Terminals and Interfaces
Table 3-1 Descriptions of Terminals and Interfaces
Interface
NC1
NO1
COM
NC2
NO2
GND
12V DC
GND
AIN2
AIN1
AIN3
AIN4
8
Description
Door Lock Relay Output (NC)
Door Lock Relay Output (NO)
Common Interface
Door Lock Relay Output (NC)
Door Lock Relay Output (NO)
Grounding
Power Supply
Grounding
For the access of Door Magnetic2
For the access of Door Magnetic1
For the access of Exit Button 1
For the access of Exit Button 2
Video Intercom Module Door Station · User Manual
No.
B5
B6
B7
B8
C
Interface
485-
485+
12V OUT
GND
LAN
Description
Module-connecting Interface
PoE Network Interface(Supports IEEE
802.3af/at-Compliant Devices)
3.1.2
Sub Module
All the modules except the main work as the sub module. The sub module’s interfaces and terminals as below:
No.
B1
B2
B3
B4
A1
A2
A3
A4
Figure 3-2 Terminals and Interfaces
Table 3-2 Descriptions of Terminals and Interfaces
Interface
485-
485+
12V IN
GND
485-
485+
12V OUT
GND
Description
Module-connecting Interface (Input)
Module-connecting Interface (Output)
9
Video Intercom Module Door Station · User Manual
3.2
Wiring Description
3.2.1
Door Lock Wiring
Figure 3-3 Door Lock Wiring
Terminal NC1/COM is set as default for accessing magnetic lock/electric bolt; terminal
NO2/COM is set as default for accessing electric strike.
Lock should be powered by itself. Max. voltage and current for relay is 30V and 1A.
10
Video Intercom Module Door Station · User Manual
3.2.2
Door Magnetic Wiring
Figure 3-4 Door Magnetic Wiring
AIN1 and AIN2 are defaulted to connect door magnetic. Door magnetic connected to
AIN1 detects status of the lock that connected to NC1/NO1; Door magnetic connected to
AIN2 detects the status of the lock connected to NC2/NO2.
3.2.3
Exit Button Wiring
Figure 3-5 Exit Button Wiring
11
Video Intercom Module Door Station · User Manual
AIN3 and AIN4 are set as default for connecting exit button. Exit button connected to
AIN3 opens the lock connected to NC1/NO1; Exit button connected to AIN4 controls the lock that connected to NC2/NO2.
12
Video Intercom Module Door Station · User Manual
4 Installation
Before you start:
Make sure the device in the package is in good condition and all the assembly parts are included.
Sub module must work along with the main unit.
Set the sub module address before start the installation steps.
Make sure the place for surface mounting is flat.
Make sure all the related equipment is power-off during the installation.
Tools that you need to prepare for installation:
Drill (ø6), cross screwdriver (PH1*150 mm), and gradienter.
Buy corresponding accessory package for installation. The accessory package model and its suitable installation method as below:
Package
Model
DS-KD-ACW1
DS-KD-ACW2
Mounting Method
One-Module Surface Mounting
Two-Module Surface Mounting
DS-KD-ACW3 Three-Module Surface Mounting
DS-KD-ACF1
DS-KD-ACF2
DS-KD-ACF3
One-Module Flush Mounting
Two-Module Flush Mounting
Three-Module Flush Mounting
Install the device according to the instructions.
Not all the lines in the accessory package will be used.
Note
4.1
Configure Sub Module Address
You need to set the sub module address via DIP before installation.
Steps:
1.
Remove the rubber cover on the sub module rear panel to expose the DIP switch.
13
Video Intercom Module Door Station · User Manual
Figure 4-1 DIP Switch
2.
Set the sub module address according to the DIP rules, and install the rubber cover back.
Digit 1, 2, 3, 4 are used to coding the sub module address; Digit 5, 6, 7 are reserved;
Digit 8 is a resistance (120Ω) is you set it as on.
Valid sub module address range is 1 to 8. The No. should be unique for sub modules that connected to the same main unit.
The sub module address and corresponding switch status as below.
Sub Module
Address
Digit 1
Digit 2
Digit 3
Digit 4
1
ON
OFF
2
OFF
ON
3
ON
ON
OFF OFF OFF
4
OFF
OFF OFF
ON
.5
ON
ON
6
OFF
ON
ON
7
ON
ON
ON
OFF OFF OFF OFF OFF OFF OFF
8
OFF
OFF
OFF
ON
4.2
One-Module Installation
4.2.1
One-Module Surface Mounting
Mounting Frame
14
Video Intercom Module Door Station · User Manual
Figure 4-1 Front and Side View
The dimension of one module mounting frame is: 117(L)
×
107(W)
×
32.7(D) mm.
The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension.
Steps:
1.
Paste the installation Sticker 1 onto the wall. Make sure the sticker is placed leveled via measuring with the gradienter.
2.
Chisel 4 holes with drill align to the screw holes on the sticker.
The suggested size of hole is 6 (diameter) × 25 (depth) mm.
The suggested length of cables left outside is 100 mm.
15
Video Intercom Module Door Station · User Manual
Figure 4-2 Chisel Screw Hole
3.
Remove the sticker and insert the expansion sleeves into the screw holes.
4.
Fix the mounting frame onto the wall with 4 expansion bolts.
16
Video Intercom Module Door Station · User Manual
Figure 4-3 Fix the Mounting Frame
The mounting frame should be placed exactly as below for this step. The tamper plate should be at the low-right.
5.
Connect the cables to the corresponding interfaces of the main unit and insert it into the frame.
17
Video Intercom Module Door Station · User Manual
Figure 4-4 Insert the Main unit
6.
Use the hexagon wrench in the package fix the cover onto the frame.
Figure 4-5 Fix the Cover
4.2.2
One-Module Flush Mounting
Gang Box
18
Video Intercom Module Door Station · User Manual
Figure 4-6 Front and Side View
Figure 4-7 Appearance Description
19
Video Intercom Module Door Station · User Manual
The dimension of one-module gang box is: 115(L)
×
134(W)
×
56(D) mm.
The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension.
Steps:
1.
Cave the installation hole, and pull the cable out.
The suggested dimension of installation hole is 118(L)
×
108(W)
×
45.5(D) mm.
The suggested length of cables left outside is 100 mm.
Figure 4-8 Cave the Installation Hole
2.
Remove the plastic sheet in the cable entry.
3.
Insert the gang box into the hole and pull out the cables through the cable entry.
Mark the screw holes’ position with a marker, and take out the gang box.
Figure 4-9 Mark the Screw Holes
4.
Chisel 4 holes with drill align to marks on the wall, and insert the expansion sleeves into the screw holes.
The suggested size of hole is 6 (diameter) × 45 (depth) mm.
5.
Fix the gang box with 4 expansion bolts.
20
Video Intercom Module Door Station · User Manual
Figure 4-10 Fix the Gang Box
6.
Fill and level up the gap between the gang box and wall with concrete. Remove the 4 mounting ears with tool after concrete is dry.
Figure 4-11 Remove the Mounting Ears
7.
Insert the mounting frame together with the locating plates into the hole, and fix it with 4 expansion bolts.
8.
Connect the cables to the corresponding interfaces of the main unit and insert it into the gang box.
Figure 4-12 Insert the Main unit
21
Video Intercom Module Door Station · User Manual
9.
Use the hexagon wrench in the package fix the cover.
Figure 4-13 Fix the Cover
4.3
Two-Module Installation
4.3.1
Two-Module Surface Mounting
Mounting Frame
22
Video Intercom Module Door Station · User Manual
Figure 4-14 Front and Side View
The dimension of two-module mounting frame is: 219(L)
×
107 (W)
×
32.7(D) mm.
The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension.
Steps:
1.
Paste the installation Sticker 1 onto the wall. Make sure the sticker is placed leveled via measuring with the gradienter.
2.
Chisel 4 holes with drill align to the screw holes on the sticker.
The suggested size of hole is 6 (diameter) × 25 (depth) mm.
The suggested length of cables left outside is 270 mm.
23
Video Intercom Module Door Station · User Manual
Figure 4-15 Chisel Screw Hole
3.
Remove the sticker and insert the expansion sleeves into the screw holes.
4.
Fix the mounting frame onto the wall with 4 expansion bolts.
Figure 4-16 Fix the Mounting Frame
The mounting frame should be placed exactly as below for this step. The tamper plate should be at the low right of the first grid.
24
Video Intercom Module Door Station · User Manual
5.
Thread the module-connecting line across the thread hole of the frame.
Pass the main unit connecting lines across the thread hole to the upper grid.
Figure 4-17 Placement of Lines
6.
Connect the cables and module-connecting line to the corresponding interfaces of the main unit, then place the main unit into the upper grid.
Connect the other end of the module-connecting line to the input interface of the sub module.
Organize the line with cable tie in the package. The suggested line connection picture as below.
25
Video Intercom Module Door Station · User Manual
Figure 4-18 Line Connection Effect Picture
7.
Insert the modules in to the frame after wiring. Main unit must be placed in the top grid.
Figure 4-19 Insert the Modules
8.
Use the hexagon wrench in the package fix the cover onto the frame.
26
Video Intercom Module Door Station · User Manual
Figure 4-20 Fix the Cover
4.3.2
Two-Module Flush Mounting
Gang Box
Figure 4-21 Front and Side View
27
Video Intercom Module Door Station · User Manual
Figure 4-22 Appearance Description
The dimension of one-module gang box is: 237(L)
×
134(W)
×
56(D) mm.
The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension.
Steps:
1.
Cave the installation hole, and pull the cable out.
The suggested dimension of installation hole is 220(L)
×
108(W)
×
45.5(D) mm.
The suggested length of cables left outside is 270 mm.
28
Video Intercom Module Door Station · User Manual
Figure 4-23 Cave the Installation Hole
2.
Remove the plastic sheet of the cable entry which will be used.
3.
Insert the gang box into the hole and pull out the cables through the cable entry.
Mark the screw holes’ position with a marker, and take out the gang box.
Figure 4-24 Mark the Screw Holes
4.
Chisel 4 holes with drill align to marks on the wall, and insert the expansion sleeves into the screw holes.
The suggested size of hole is 6 (diameter) × 45 (depth) mm.
5.
Fix the gang box with 4 expansion bolts.
29
Video Intercom Module Door Station · User Manual
Figure 4-25 Fix the Gang Box
6.
Fill and level up the gap between the gang box and wall with concrete. Remove the mounting ears with tool after concrete is dry.
Figure 4-26 Remove the Mounting Ears
7.
Connect wires and insert the modules: a. Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the main unit, then place the main unit into the upper grid. b. Connect the other end of Cable 2 to the input interface of the sub module. Insert it into the lower grid.
30
Video Intercom Module Door Station · User Manual
Figure 4-27 Connect Wires and Insert Modules
Cable 1 refers to the cables pulled out from the wall that connected to the main unit.
Cable 2 refers to the module-connecting line in the accessory package.
8.
Use the hexagon wrench in the package fix the cover.
Figure 4-28 Fix the Cover
31
Video Intercom Module Door Station · User Manual
4.4
Three-Module Installation
4.4.1
Three-Module Surface Mounting
Installation Frame
Figure 4-29 Front and Side View
The dimension of two-module mounting frame is: 320.8(L)
×
107 (W)
×
32.7(D) mm.
The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension.
Steps:
1.
Paste the installation Sticker 1 onto the wall. Make sure the sticker is placed leveled via measuring with the gradienter.
2.
Chisel 4 holes with drill align to the screw holes on the sticker.
The suggested size of hole is 6 (diameter) × 25 (depth) mm.
The suggested length of cables left outside is 270 mm.
32
Video Intercom Module Door Station · User Manual
Figure 4-30 Chisel Screw Hole
3.
Remove the sticker and insert the expansion sleeves into the screw holes.
4.
Fix the mounting frame onto the wall with 4 expansion bolts.
Figure 4-31 Fix the Mounting Frame
33
Video Intercom Module Door Station · User Manual
The mounting frame should be placed exactly as below for this step. The tamper plate should be at the low right of the first grid.
5.
Thread the module-connecting lines across the thread holes of the frame.
Pass the main unit connecting lines across the thread hole to the top grid.
34
Video Intercom Module Door Station · User Manual
Figure 4-32 Placement of Lines
6.
Connect the cables and module-connecting line 1 to the corresponding interfaces of the main unit, then place the main unit into the upper grid.
Connect the other end of the module-connecting line1 to the input interface of the sub module. Connect two sub modules via module-connecting line 2.
Organize the line with cable tie in the package. The suggested line connection picture as below.
35
Video Intercom Module Door Station · User Manual
Figure 4-33 Line Connection Effect Picture
7.
Insert the modules in to the frame after wiring. Main unit must be placed in the top grid.
36
Video Intercom Module Door Station · User Manual
Figure 4-34 Insert the Modules
8.
Use the hexagon wrench in the package fix the cover onto the frame.
Figure 4-35 Fix the Cover
4.4.2
Three-Module Flush Mounting
Gang Box
37
Video Intercom Module Door Station · User Manual
Figure 4-36 Front and Side View
38
Video Intercom Module Door Station · User Manual
Figure 4-37 Appearance Description
The dimension of one-module gang box is: 338.8(L)
×
134(W)
×
56(D) mm.
The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension.
Steps:
1.
Cave the installation hole, and pull the cable out.
The suggested dimension of installation hole is 321.8(L)
×
108(W)
×
45.5(D) mm.
The suggested length of cables left outside is 270 mm.
39
Video Intercom Module Door Station · User Manual
Figure 4-38 Cave the Installation Hole
2.
Remove the plastic sheet of the cable entry which will be used.
3.
Insert the gang box into the hole and pull out the cables through the cable entry.
Mark the screw holes’ position with a marker, and take out the gang box.
Figure 4-39 Mark the Screw Holes
4.
Chisel 4 holes with drill align to marks on the wall, and insert the expansion sleeves into the screw holes.
The suggested size of hole is 6 (diameter) × 45 (depth) mm.
5.
Fix the gang box with 4 expansion bolts.
40
Video Intercom Module Door Station · User Manual
Figure 4-40 Fix the Gang Box
6.
Fill and level up the gap between the gang box and wall with concrete. Remove the mounting ears with tool after concrete is dry.
Figure 4-41 Remove the Mounting Ears
7.
Connect wires and insert the modules: a. Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the
Main Unit, then place the Main Unit into the upper grid. b. Connect the other end of Cable 2 to the input interface of Sub Module 1. Connect one end of Cable 3 to the output interface of Sub Module 1 and insert it into the middle grid.
41
Video Intercom Module Door Station · User Manual c. Connect the other end of Cable 3 to the input interface of Sub Module 2. Insert it into the bottom grid.
Figure 4-42 Connect Wires and Insert Modules
Cable 1 refers to the cables pulled out from the wall that connected to the main unit.
Cable 2 and Cable 3 refer to the module-connecting line in the accessory package.
8.
Use the hexagon wrench in the package to fix the cover onto the gang box.
42
Video Intercom Module Door Station · User Manual
Figure 4-43 Fix the Cover
43
Video Intercom Module Door Station · User Manual
4.5
More-than-Three Module Installation
4.5.1
More-than-Three Module Surface Mounting
Figure 4-44 Front and Side View
It takes two three-module mounting frames. The dimension of three-module mounting frame is: 320.8(L)
×
107 (W)
×
32.7(D) mm.
The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension.
Steps:
1.
Paste two Sticker 1 onto the wall. Make sure the stickers are placed leveled via measuring with the gradienter.
2.
Chisel 8 holes with drill align to the screw holes on the sticker.
The suggested size of hole is 6 (diameter) × 25 (depth) mm.
The suggested length of cables left outside is 270 mm.
44
Video Intercom Module Door Station · User Manual
3.
Pull out the cable through the cable hole of the left sticker.
Figure 4-45 Chisel Screw Hole
4.
Remove the stickers and insert the expansion sleeves into the screw holes.
5.
Thread the module-connecting line (400 mm) and grounding line across the thread hole of both frames.
Figure 4-46 Place the Grounding Line and Module-Connecting Line
45
Video Intercom Module Door Station · User Manual
There are 6 module-connecting lines in the package: 190 mm *4 and 400 mm*2.
Take the 400 mm one for this step.
The green-yellow line in the package is for grounding.
6.
Fix the mounting frame onto the wall with 8 expansion bolts.
Figure 4-47 Fix the Mounting Frame
The mounting frame should be placed exactly as below for this step. The tamper plate should be at the low right of the first grid.
46
Video Intercom Module Door Station · User Manual
7.
Pass the main unit connecting lines across the thread hole to the top grid of the left frame.
Thread the module-connecting line (190 mm) across the thread hole of the frame.
The lines should be placed as below:
Figure 4-48 Placement of Lines
47
Video Intercom Module Door Station · User Manual
8.
Connect the cables and module-connecting line 1 to the corresponding interfaces of the main unit, then place the main unit into the upper grid.
Connect the other end of the module-connecting line1 to the input interface of the sub module. Connect all sub modules via module-connecting lines.
Organize the line with cable tie in the package. The suggested line connection picture as below.
Figure 4-49 Line Connection Effect Picture
9.
Insert the modules in to the frame after wiring. Main unit must be placed in the top grid on the left.
48
Video Intercom Module Door Station · User Manual
Figure 4-50 Insert the Modules
10.
Pull the grounding line out and fixed its two end to the screw on the cover.
Figure 4-51 Connect the Grounding Line to the Cover
11.
Use the hexagon wrench in the package fix the cover onto the frame.
49
Video Intercom Module Door Station · User Manual
Figure 4-52 Fix the Cover
4.5.2
More-than-Three Module Flush Mounting
Gang Box
50
Video Intercom Module Door Station · User Manual
Figure 4-53 Front and Side View
51
Video Intercom Module Door Station · User Manual
Figure 4-54 Appearance Description
It takes two three-module gang boxes. The dimension of the gang box is: 338.8(L)
×
134 (W)
×
56(D) mm.
The dimensions above are for reference only. The actual size can be slightly different from the theoretical dimension.
Steps:
1.
Cave the installation hole, and pull the cable out.
The suggested dimension of installation hole is 321.8(L)
×
315(W)
×
45.5(D) mm.
The suggested length of cables left outside is 270 mm.
52
Video Intercom Module Door Station · User Manual
Figure 4-55 Cave the Installation Hole
2.
Connect the two gang boxes as the below.
Figure 4-56 Cave the Installation Hole
3.
Remove the plastic sheet of the cable entry which will be used.
4.
Remove the plastic sheets on the side of the gang boxes (shown as 1 and 2) blow:
53
Video Intercom Module Door Station · User Manual
Figure 4-57 Remove the Plastic Sheets
5.
Insert the gang boxes into the hole and pull out the cables through the cable entry.
Mark the screw holes’ position with a marker, and take out the gang boxes.
Figure 4-58 Mark the Screw Holes
6.
Chisel 8 holes with drill align to marks on the wall, and insert the expansion sleeves into the screw holes.
The suggested size of hole is 6 (diameter) × 45 (depth) mm.
7.
Fix the gang boxes with 8 expansion bolts.
54
Video Intercom Module Door Station · User Manual
Figure 4-59 Fix the Gang Boxes
8.
Fill and level up the gap between the gang box and wall with concrete. Remove the mounting ears with tool after concrete is dry.
Figure 4-60 Remove the Mounting Ears
55
Video Intercom Module Door Station · User Manual
9.
Pass the grounding line through the cable entries.
Figure 4-61 Place the Grounding Line
The green-yellow line in the package is for grounding.
10.
Connect wires and insert the modules. a. Connect Cable 1 and one end of Cable 2 to the corresponding interfaces of the
Main Unit, then place the Main Unit into the upper grid of the left gang box. b. Connect the other end of Cable 2 to the input interface of Sub Module 1. Connect one end of Cable 3 to the output interface of Sub Module 1 and insert it into the middle grid of the left gang box. c. Finish the wiring and inserting according to the cable number and the position shown as below.
56
Video Intercom Module Door Station · User Manual
Figure 4-62 Install Mounting Frames
The cables connect to each module shown as below:
Figure 4-63 Install Mounting Frames
57
Video Intercom Module Door Station · User Manual
Cable 2,3,5 and 6 are the module-connecting lines (190 mm) in the package.
Cable 4 is the module-connecting line (400 mm) in the package.
Main unit must be put in the top grid.
11.
Pull the grounding line out and fixed its two end to the screw on the cover.
Figure 4-64 Connect the Grounding Line to the Cover
12.
Use the hexagon wrench in the package fix the cover onto the gang box.
Figure 4-65 Fix the Cover
58
Video Intercom Module Door Station · User Manual
5 Device Configuration
You need to activate device and configure corresponding parameters via iVMS-4200 before use.
5.1
Activate Device
You cannot use the door station until you activate it.
You can configure and operate the video intercom devices via iVMS-4200.
Default parameters of door station are as follows:
Default IP Address: 192.0.0.65.
Default Port No.: 8000.
Default User Name: admin.
Steps:
1.
Run iVMS-4200, enter Device Management, check the Online Device area.
2.
Select an inactivated device and click the Activate button.
3.
Create a password, and confirm the password.
59
Video Intercom Module Door Station · User Manual
STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
4.
Click the OK button to activate the device.
When the device is not activated, the basic operation and remote operation of device cannot be performed.
You can hold the Ctrl or Shift key to select multiple devices in the online devices, and click the Activate button to activate devices in batch.
5.2
Edit Network Parameters
Purpose:
To operate and configure the device via LAN (Local Area Network), you need connect the device in the same subnet with your PC. You can edit network parameters via iVMS-4200 software.
Steps:
1.
Select an online activated device and click the Modify Netinfo button.
2.
Change the device IP address and gateway address to the same subnet with your computer.
3.
Enter the password and click the OK button to activate the network parameters modification.
60
Video Intercom Module Door Station · User Manual
The default port No. is 8000.
The default IP address of the door station is 192.0.0.65.
After editing the network parameters of device, you should add the devices to the device list again.
5.3
Add Device
You can add at most 16 door stations to the iVMS-4200.
For the device, you are required to create the password to activate them before they can be added to the software and work properly.
You can add online devices, and add them manually. Here take adding online video intercom devices as example.
Steps:
1.
Click the icon on the control panel, or click Tools->Device Management to open the Device Management page.
2.
Click Device.
3.
On the Device Type panel on the right, you can select Hikvision Device to add video intercom devices.
4.
The active online devices in the same local subnet with the client software will be displayed on the Online Device area. You can click Refresh Every 60s to refresh the information of the online devices.
61
Video Intercom Module Door Station · User Manual
To add online devices to the software, you are required to change the device IP address to the same subnet with your computer first.
5.
Select the devices to be added from the list.
6.
Click Add to Client to open the device adding dialog box.
7.
Input the required information.
Nickname: Edit a name for the device as you want.
Address: Input the device’s IP address. The IP address of the device is obtained automatically in this adding mode.
Port: Input the device port No. The default value is 8000.
User Name: Input the device user name. By default, the user name is admin.
Password: Input the device password. By default, the password is 12345 .
Optionally, you can check the checkbox Export to Group to create a group by the device name. All the channels of the device will be imported to the corresponding group by default. iVMS-4200 also provides a method to add the offline devices. Check the checkbox
Add Offline Device, input the required information and the device channel number and alarm input number, and then click Add. When the offline device comes online, the software will connect it automatically.
8.
Click Add to add the device.
62
Video Intercom Module Door Station · User Manual
Add Multiple Online Devices
If you want to add multiple online devices to the client software, click and hold Ctrl key to select multiple devices, and click Add to Client to open the device adding dialog box.
In the pop-up message box, enter the user name and password for the devices to be added.
Add All the Online Devices
If you want to add all the online devices to the client software, click Add All and click OK in the pop-up message box. Then enter the user name and password for the devices to be added.
5.4
Reset Password
You can restore the default password or resetting the password for the door station.
Select the device from the online device list, click Reset Password.
If the window with import file button, key importing mode drop-down list, password and confirm password field pops up, follow the steps below to reset the password:
This option is available to door stations.
63
Video Intercom Module Door Station · User Manual
1.
Click Export to save the device file on your computer.
2.
Send the file to our technical engineers.
3.
Our technical engineer will send you a file to you. After receiving a file from the technical engineer, select Import File from Key Importing Mode drop-down list and click to import the file.
4.
Input new password in text fields of Password and Confirm Password.
5.
Click OK to reset the password.
STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system,
resetting the password monthly or weekly can better protect your product.
64
Video Intercom Module Door Station · User Manual
5.5
Configure System Parameters
In the device list area, select a device and click the remote configuration interface.
or to enter
Click the System button on the remote configuration interface to display the device information: Device Information, General, Time, System Maintenance, User, and so on.
5.5.1
Device Information
Click the Device Information button to enter device basic information interface. You can view basic information (the device type, and serial No.), and version information of the device.
5.5.2
General
Click the General button to enter device general parameters settings interface. You can view and edit the device name and device ID.
5.5.3
Time
Steps:
65
Video Intercom Module Door Station · User Manual
1.
Click the Time button to enter the device time settings interface.
2.
Select Time Zone or Enable NTP.
Time Zone
1) Select a time zone from the drop-down list menu.
2) Click the Synchronization button.
NTP
1) Check the checkbox of Enable NTP to enable NTP.
2) Enter the server address, NTP port, and synchronization interval.
DST
1) Check the checkbox of Enable DST to enable DST.
2) Enter the start time and end time of DST, and set the DST bias.
3.
Click the Save button to save and realize the time settings.
The default port No. is 123.
5.5.4
System Maintenance
Purpose:
You can operate the system management and remote upgrading on the system maintenance interface.
Steps:
1.
Click the System Maintenance button to enter the system maintenance interface.
66
Video Intercom Module Door Station · User Manual
2.
Click Reboot and the system reboot dialog box pops up. Click Yes to reboot the system.
3.
Click Restore Default Settings to restore the default parameters.
4.
Click Restore All to restore all parameters of device and reset the device to inactive status.
5.
Click Import Configuration File and the import file window pops up. Select the path of remote configuration files. Click Open to import the remote configuration file. The configuration file is imported and the device will reboot automatically.
6.
Click Export Configuration File and the export file window pops up. Select the saving path of remote configuration files and click Save to export the configuration file.
67
Video Intercom Module Door Station · User Manual
7.
Click to select the upgrade file and click Upgrade to remote upgrade the device.
The process of remote upgrade will be displayed in the process bar.
Figure 5-1 Remote Upgrade
Click Restore Default Settings button, all default settings, excluding network parameters, will be restored.
Click Restore All button, all default settings, including network parameters, will be restored. The device will be reset to inactivated status.
5.5.5
User
Purpose:
You can edit the password for logging in the device.
Steps:
1.
Click the User button to enter the user information editing interface.
2.
Select the user to edit and click the Modify button to enter the user parameter interface.
68
Video Intercom Module Door Station · User Manual
3.
Enter the new password, and confirm it.
4.
Click the Save button to realize the editing of password.
The new password and confirm password should be identical.
After editing the password of device, click button from the device list, the added device will not be there. You should add the device again with new password to operate the remote configuration.
5.6
Configure Video Intercom Parameters
Click the Video Intercom button on the remote configuration interface to enter the video intercom parameters settings: Device Number Configuration, Time Parameters,
Access and Elevator Control, IO Input/Output, Volume, Dial, Sub Module and so on.
5.6.1
Device ID Configuration
Steps:
1.
Click the ID Configuration button to enter device ID configuration interface.
69
Video Intercom Module Door Station · User Manual
2.
Select the device type from the drop-down list, and set the corresponding information.
3.
Click the Save button to enable the device number configuration.
For main door station, the serial No. is 0.
For sub door station, the serial No. is higher than 0. Serial No. ranges from 1 to 99.
For each villa or building, at least one main door station should be configured, and sub door stations can be customized.
For one main door station, at most 8 sub door stations can be customized.
5.6.2
Time Parameters
1.
Click the Time Parameters button to enter time parameters settings interface.
2.
Configure the maximum ring duration, maximum live view time, and call forwarding time.
3.
Click the Save button.
For door station, maximum speaking time and maximum message time should be configured. Maximum speaking time varies from 90s to 120s, and maximum message time varies from 30s to 60s.
5.6.3
Permission Password
1.
Click Permission Password button to enter the permission password interface.
70
Video Intercom Module Door Station · User Manual
2.
Edit the password accordingly.
3.
Click the Save button to enable the settings.
You can configure 3 public passwords.
You can open the door by entering
【
#
】
+ public password +
【
#
】 at the door station.
5.6.4
Access Control and Elevator
Click Access Control and Elevator to enter corresponding configuration page.
71
Video Intercom Module Door Station · User Manual
Access Control
1.
Select the door No..
2.
Set the door-unlocked duration.
3.
(Optional) Enable Upload Alarm for Not-Closed Door.
4.
Click Save to enable the settings.
The door-unlocked duration ranges from 1s to 225s.
If you check Upload Alarm for Not-Closed Door, an alarm will be triggered automatically if the door is not locked in the configured duration.
Enabling Card Encrypt, the door station can recognize the encrypted information of the card when you swiping the card on the door station.
Elevator Control
Before you start
72
Video Intercom Module Door Station · User Manual
Make sure your door station is in the mode of main door station. Only the main door station support elevator control function.
Connection between the door station and the elevator controller supports network interface.
Step:
1.
Select an elevator No., and select an elevator controller type for the elevator.
2.
Set the negative floor.
3.
Select the interface type: network Interface, enter the elevator controller’s IP address, port No., user name, and password.
4.
Enable the elevator control.
Up to 4 elevator controllers can be connected to one door station.
Up to 10 negative floors can be added.
Make sure the interface types of elevator controllers, which are connected to the same door station, are consistent.
5.6.5
IO Input and Output
Step:
1.
Click the I/O Input and Output button to enter the I/O input and output interface.
2.
Select I/O input No., input mode, output No., and output mode.
3.
Click the Save button to enable the settings.
For door station, there are 4 I/O Input Terminals. By default, Terminal 1and 2 correspond to Door Status. Terminal 3 and 4 correspond to interfaces of Door
Switch.
73
Video Intercom Module Door Station · User Manual
For door station, there are 2 I/O Output Terminals. Terminal 1~2 correspond to
DOOR interfaces (NO1/COM/NC1; NO2/COM/NC2) of door station. Door 1 is enabled by default. You can enable/disable IO Out according to needs.
5.6.6
Volume Input and Output
Step:
1.
Click Volume Input/Output button to enter the volume input and output interface.
2.
Slide the slider to adjust the volume input, volume output, and talk volume.
3.
Click the Save button to enable the settings.
5.6.7
Dial
Step:
1.
Click Dial button to enter the dial interface.
2.
Enter the room No. of the indoor station that the door station connected to.
3.
Click the Save button to enable the settings.
By default, quick press the call button, the door station calls resident. If you check
Quick Press for Calling Center, the door station calls the management center when quick press the call button of the main unit.
74
Video Intercom Module Door Station · User Manual
5.6.8
Motion Detection
Step:
1.
Click Motion Detection button to enter the motion detection interface.
2.
Check Enable Motion Detection to enable the function.
3.
Configure the parameters accordingly.
4.
Click the Save.
The arming schedule is defaulted as all-day.
5.6.9
Intercom Protocol
Step:
1.
Click Intercom Protocol button to enter the intercom protocol interface.
75
Video Intercom Module Door Station · User Manual
2.
Select the protocol according to needs.
Configure the related parameters, if you select SIP Protocol.
3.
Click the Save.
5.6.10
Sub Module
Step:
1.
Click Sub Module button to enter the sub module configuration interface.
2.
Click to pop up the configuration interface.
3.
(Optional) Enter the room no. for each call button of the nametag module.
76
Video Intercom Module Door Station · User Manual
4.
Click the Save button to enable the settings.
The module address is used to differentiate the sub modules. See Configure Sub
Module Address for detailed configuration instructions.
For the other sub modules (indicator module, keypad module, and card reader module), it prompts Not supported.
The room No. for the main unit’s call button is 1 by default; and the room No. for the nametag modules call buttons are 2 to 7 by default.
5.7
Configure Video Intercom Network
You need to configure video intercom network parameters in the network module.
Click Network in the remote configuration interface, to configure the local network, linked network and FTP settings.
77
Video Intercom Module Door Station · User Manual
5.7.1
Local Network Configuration
Steps:
1.
Click the Local Network Configuration button to enter local network configuration interface.
2.
Enter the local IP address, subnet mask, gateway address, Port and HTTP Port.
3.
Click the Save button to enable the settings.
The default port No. is 8000.
After editing the local network parameters of device, you should add the devices to the device list again.
5.7.2
Linked Devices Network Configuration
Purpose:
In the linked devices network configuration interface, you can configure the network parameters of master stations, SIP servers and management centers of the same LAN.
The devices can be linked to the door station and realize the linkage between these devices.
Steps:
1.
Click the Linked Network Configuration button to enter linked network configuration interface.
2.
Enter the master station IP address, (main) door station IP address, SIP server IP address, management center IP address, and Port No..
3.
Select the main door station type from the drop-down list.
4.
Click the Save button to enable the settings.
78
Video Intercom Module Door Station · User Manual
After adding master station IP Address, the linkage between indoor station and master station can be realized.
After adding the door station IP Address, the video intercom between indoor stations of same building can be realized.
After adding SIP Server Address IP, the video intercom of same community: video intercom between indoor stations of different building, calling indoor station from outer door station and video intercom between management center and indoors.
After adding management center IP Address, the events can be uploaded to the management center.
For indoor extension, only parameter about the main indoor station should be configured.
5.7.3
FTP
After configuring the FTP parameters, the captured pictures of door station will be uploaded to the FTP server automatically.
Steps:
1.
Click the FTP button to enter the FTP parameters interface.
2.
Check the checkbox of Enable Main FTP.
79
Video Intercom Module Door Station · User Manual
3.
Select IP address from the drop-down list of server mode.
4.
Enter the FTP server address, and port No..
5.
Check the checkbox to enable the anonymity (optional).
6.
Enter the name and password.
7.
Select the directory structure and set the separator, naming item, and naming element.
8.
Click the Save button to enable the FTP parameters settings.
The default port No. is 21.
To enable anonymity or not is according to whether the FTP server enables anonymity.
5.7.4
Advanced Settings
Steps:
1.
Click the Advanced Settings button to enter the advanced network settings interface.
2.
Enter the DNS server addresses.
3.
Click the Save button to enable the advanced network settings.
5.8
Person and Card Management
Purpose:
You can add, edit, and delete the organization and person in Person and Card
Management module. Organization and person management is necessary for the video intercom function.
Before you start:
For the first time opening the Access Control module, the following dialog will pop up and you are required to select the scene according to the actual needs.
You can select the scene as Non-residence and Residence.
80
Video Intercom Module Door Station · User Manual
Once the scene is configured, you cannot change it later.
Click - > tab to enter the Person and Card Management interface.
The interface is divided into two parts: Organization Management and Person
Management.
1
Organization
Management
You can add, edit, or delete the organization as desired.
2 Person Management
After adding the organization, you can add the person to the organization and issue card to persons for further management.
81
Video Intercom Module Door Station · User Manual
5.8.1
Organization Management
Add Organization
Steps:
1.
In the organization list on the left, you should add a top organization as the parent organization of all organizations.
Click Add button to pop up the adding organization interface.
2.
Input the Organization Name as desired.
3.
Click OK to save the adding.
4.
You can add multiple levels of organizations according to the actual needs.
To add sub organizations, select the parent organization and click Add.
Repeat Step 2 and 3 to add the sub organization.
Then the added organization will be the sub-organization of the upper-level organization.
Up to 10 levels of organizations can be created.
Modify and Delete Organization
You can select the added organization and click Modify to modify its name.
You can select an organization, and click Delete button to delete it.
The lower-level organizations will be deleted as well if you delete an organization.
Make sure there is no person added under the organization, or the organization cannot be deleted.
5.8.2
Person Management
After adding the organization, you can add person to the organization and manage the added person such as issuing cards in batch, importing and exporting person’s information in batch, etc.
Up to 10,000 persons or cards can be added.
82
Video Intercom Module Door Station · User Manual
Add Person
Person information is necessary for the video intercom system. And when you set linked device for the person, the intercom between intercom devices can be realized.
Steps:
1.
Select an organization in the organization list and click Add on the Person panel to pop up the adding person dialog.
The Person No. will be generated automatically and is not editable.
2.
Set basic person information.
1) Enter basic information: person name, gender, phone No., birthday details,
83
Video Intercom Module Door Station · User Manual and email address.
2) (Optional) Click Upload Picture to select the person picture from the local PC to upload it to the client.
The picture should be in *.jpg format.
3) (Optional) You can also click Take Phone to take the person’s photo with the
PC camera.
3.
Set linked device for the person.
1) Click Details.
2) Set the linked devices
Linked Device: You can bind the indoor station to the person.
If you select Analog Indoor Station in the Linked Device, the Door
Station field will display and you are required to select the door station to communicate with the analog indoor station.
Room No.: You can enter the room No. of the person.
Floor No.: You have to set the floor No. for calling the elevator via swiping card.
3) Click OK to save the settings.
4.
Issue the card for the person.
1) Click Card.
84
Video Intercom Module Door Station · User Manual
2) Click Add to pop up the Add Card dialog.
3) Select Normal Card.
85
Video Intercom Module Door Station · User Manual
4) Select the card reader mode, and fill related information.
5) Click OK and the card(s) will be issued to the person.
Import and Export Person Information
The person information can be imported and exported in batch.
Steps:
1.
Exporting Person: You can export the added persons’ information in Excel format to the local PC.
1) After adding the person, you can click Export Person button to pop up the following dialog.
2) Click to select the path of saving the exported Excel file.
3) Check the checkboxes to select the person information to export.
4) Click OK to start exporting.
2.
Importing Person: You can import the Excel file with persons information in batch from the local PC
1) click Import Person button.
86
Video Intercom Module Door Station · User Manual
2) You can click Download Template for Importing Person to download the template first.
3) Input the person information to the downloaded template.
4) Click to select the Excel file with person information.
5)
Click OK to start importing.
Get Person Information from Device
If the added device has been configured with person information (including person details, fingerprint, issued card information), you can get the person information from the device and import to the client for further operation.
This function is only supported by the device the connection mothod of which is TCP/IP when adding the device.
Steps:
1.
In the organization list on the left, click to select an organization to import the persons.
2.
Click Get Person to pop up the following dialog box.
87
Video Intercom Module Door Station · User Manual
3.
The added access control device will be displayed.
4.
Click to select the device and then click OK to start getting the person information from the device.
You can also double click the device name to start getting the person information.
The person information, including person details, person’s fingerprint information
(if configured), and the linked card (if configured), will be imported to the selected organization.
If the person name stored in the device is empty, the person name will be filled with the issued card No. after importing to the client.
The gender of the persons will be Male by default.
Modify and Delete Person
To modify the person information and attendance rule, click or in the
Operation column, or select the person and click Modify to open the editing person dialog.
You can click to view the person’s card swiping records.
To delete the person, select a person and click Delete to delete it.
If a card is issued to the current person, the linkage will be invalid after the person is deleted.
Change Person to Other Organization
You can move the person to another organization if needed.
88
Video Intercom Module Door Station · User Manual
Steps:
1.
Select the person in the list and click Change Organization button.
2.
Select the organization to move the person to.
3.
Click OK to save the settings.
Issue Card in Batch
You can issue multiple cards for the person with no card issued in batch.
Steps:
1.
Click Issue Card in Batch to enter the following dialog.
All the added person with no card issued will display in the Person(s) with No Card
Issued list.
2.
Select Normal Card.
3.
Enter the card quantity issued for each person.
89
Video Intercom Module Door Station · User Manual
For example, if the Card Quantity is 3, you can read or enter three card No. for each person.
4.
Select the card reader mode and fill related information. Click Read/Enter.
5.
After issuing the card to the person, the person and card information will display in the Person(s) with Card Issued list.
6.
Click OK to save the settings.
5.9
Video Display
5.9.1
Video Parameters
Steps:
1.
Click the Video Parameters button to enter the video parameters interface.
2.
Select the camera No..
3.
Select the video standard (PAL and NTSC can be selected).
4.
Set WDR mode (Disable or Enable).
5.
Set the brightness, contrast, saturation and sharpness of the video.
6.
Click the Save button to enable the settings.
90
Video Intercom Module Door Station · User Manual
Click the Restore Default Settings button to restore all video parameters excluding network parameters to the factory settings.
5.9.2
Video & Audio
Steps:
1.
Click the Video & Audio button to enter the video parameters settings interface.
2.
Set the parameters accordingly.
3.
Click the Save button to enable the settings.
It’s suggested to keep the default settings to ensure the video/image quality.
5.10
BLC Mode
You can set the BLC mode according to needs.
Steps:
1.
Click the Back Light Compensation button to enter the back light compensation settings interface.
91
Video Intercom Module Door Station · User Manual
2.
Set the BLC mode.
3.
Click Save.
92
Video Intercom Module Door Station · User Manual
6 Video Intercom Operation
6.1
Video Intercom Operation via Device
6.1.1
Call Resident
You can call corresponding resident in two ways:
1.
Press the call button on the main unit or on the nametag unit.
2.
Enter the Room No. on the keypad module, and press # key to start calling.
(Press * to hang up.)
Make sure you have configured the room No. for the device.
6.1.2
Issue Card
You cannot open door by swiping the card until you have issue the card.
You can issue the card both locally or remotely. See5.8.2 Person Management for issuing
card via 4200.
Issue Card via Main Card: You can swipe card to issue it after swiping the main card in advance.
Steps:
1.
Swipe the main card on the card reading area, and hear two beeps.
2.
Swipe the unauthorized sub cards in turn after hearing a beep.
3.
Swipe the main card again to end the card issuing process.
DS-KD-M supports Mifare card, DS-KD-E supports EM card.
If the amount of sub cards exceeds 2500, no more sub card can be issued.
6.1.3
Unlock Door
Unlock Door by Password
You can unlock the door by inputting the password via the keypad module.
Three formats of password are supported. They are:
1.
【
#
】
+ Public Password +
【
#
】
2.
【
#
】
+ Room No. + Password +
【
#
】
3.
【
#
】
+ Room No. + Duress Password +
【
#
】
93
Video Intercom Module Door Station · User Manual
Password contains 6 digits.
You’re allowed to set 3 public passwords via iVMS-4200.
The password varies according to different rooms.
Unlock Door by Card
Before you start:
Make sure the card has been issued. You can issue the card via the door station, or via iVMS-4200 client software.
Steps:
Swipe the card on the card induction area to unlock the door.
The main card does not support unlocking the door.
6.2
Video Intercom Operation via iVMS-4200
Purpose:
The Video Intercom Management module provides the function of video intercom, checking call logs and managing notice via the iVMS-4200 client software.
For the user with access control module permissions, the user can enter the Access
Control module and manage video intercom and search information.
Before you start:
Before you can remote control the video intercom, you should add the device to the software and configure the person to link the device in the Access Control module.
Click -> tab on the left icon bar to enter the Video Intercom interface.
6.2.1
Receive Call from Door Station
Steps:
1.
Select the client software in door station interface to start calling the iVMS-4200 and an incoming call dialog will pop up in the client software.
94
Video Intercom Module Door Station · User Manual
2.
Click Answer to answer the call.
Or click Hang Up to decline the call.
3.
After you answer the call, you will enter the In Call window.
Click to adjust the volume of the loudspeaker.
Click to hang up.
95
Video Intercom Module Door Station · User Manual
Click to adjust the volume of the microphone.
For door station, you can click to open the door remotely.
One video intercom device can only connect with one client software.
The maximum ring duration can be set from 15s to 60s via the Remote
Configuration of the video intercom device.
The maximum speaking duration between indoor station and iVMS-4200 can be set from 120s to 600s via the Remote Configuration of indoor station.
The maximum speaking duration between door station and iVMS-4200 can be set from 90s to 120s via the Remote Configuration of door station.
6.2.2
View Live Video of Door Station
You can get the live view of the main unit in the Main View module and control the door station remotely.
In the Main View module, double-click a door station or drag the device to a display window to start the live view.
Right click on the live view interface, click the unlock icon to remote unlock the door.
6.2.3
View Call Logs
Purpose:
You can check all the call logs, including dialed call logs, received call logs and missed call logs. You can also directly dial via the log list and clear the logs.
96
Video Intercom Module Door Station · User Manual
Steps:
1.
In the Video Intercom page, click the Call Log tab to enter the Call Log page.
All the call logs will display on this page and you can check the log information, e.g., call status, start time, resident’s organization and name, device name and ring or speaking duration.
2.
(Optional) Click the icon in the Operation column to re-dial the resident.
3.
(Optional) Click the icon in the Operation column to delete the call log.
Or you can click Clear at the upper right corner to clear all the logs.
6.2.4
Search Video Intercom Information
Purpose:
You can search the call logs between the iVMS-4200 client software and video intercom devices, device unlocking logs and the sent notice information.
In the Access Control module, click icon tab to open the Search page.
Search Call Logs
Steps:
1.
In the Information Search page, click the Call Log to enter the Call Log interface.
97
Video Intercom Module Door Station · User Manual
2.
Set the search conditions, including call status, device type, start time and end time.
Call Status: Click to unfold the drop-down list and select the call status as
Dialed, Received or Missed. Or select All to search logs with all statuses.
Device Type: Click to unfold the drop-down list and select the device type as Indoor Station, Door Station, Outer Door Station or Analog Indoor
Station. Or select All Devices to search logs with all device types.
Start Time/End Time: Click to specify the start time and end time of a time period to search the logs.
(Optional) You can click Reset to reset all the configured search conditions.
3.
Click Search and all the matched call logs will display on this page.
For the search results,
(Optional) Check the detailed information of searched call logs, such as call status, ring/speaking duration, device name, resident organization, etc.
(Optional) Input keywords in the Search field to filter the desired log.
(Optional) Click Export to export the call logs to your PC.
Search Unlocking Logs
Steps:
1.
In the Information Search page, click Unlocking Log tab to enter the Unlocking Log interface.
98
Video Intercom Module Door Station · User Manual
2.
Set the search conditions, including unlocking type, device type, start time and end time.
Unlocking Type: Click to unfold the drop-down list and select the unlocking type as Unlock by Password, Unlock by Duress, Unlock by Card,
Unlock by Resident or Unlock by Center. Or select All to search logs with all unlocking types.
Device Type: Click to unfold the drop-down list and select the device type as Door Station or Door Station (V Series). Or select All Devices to search logs with all device types.
Start Time/End Time: Click to specify the start time and end time of a time period to search the logs.
3.
(Optional) You can click Reset to reset all the configured search conditions.
4.
Click Search and all the matched unlocking logs will display on this page.
For the searching results,
(Optional) Check the detailed information of searched unlocking logs, such as unlocked time, card No., device No., etc.
(Optional) Input keywords in the Search field to filter the searching result.
(Optional) Click in the Capture column to view the captured pictures.
Viewing captured picture should be supported by device.
(Optional) Click Export to export the unlocking logs to your PC.
99
1
UD11560B-A
Advertisement
