ab Platinum Series User Manual
Advertisement
Advertisement
www.AdvancedBionics.com
Advanced Bionics AG
Laubisrütistrasse 28
8712 Stäfa, Switzerland
+41 58 928 78 00
MANUFACTURED BY:
Advanced Bionics LLC
California, USA
+1 661 362 1400
029-M296-03 Rev B
©2013 Advanced Bionics AG and its affiliates. All rights reserved.
USER GUIDE
PLATINUM SERIES
™
Sound Processor
By Advanced Bionics
User Guide
for the Platinum Series
™
Sound Processor
PLATINUM SERIES
By Advanced Bionics
Labeling
The symbols below are used on the labeling for the product and for transportation, and their meanings are as follows:
CAUTION: Federal law restricts this device to sale, distribution and use by or on the order of a physician .
European Community Mark of Conformity
Authorized to affix the CE Mark in 2000
REF Model Number
Manufacturer
Fragile
SN Serial Number
Store at temperatures between -20° C and
+55° C
Do not get wet
Type of Protection: B
Date of Manufacture
2000-00
See Instructions for Use
Dispose of in accordance with applicable national and local regulations
Pressure tolerance is between 70 .0 kPa and 106 kPa, which is equivalent to 3000m above sea level and
380m below sea level .
Suitable for exposure to relative humidity between
0-95%
EN60601-1 Classification Information:
• Continuous Operation
• Internally Powered Equipment
• Type B Equipment
• Altitude: Suitable to operate from 380m below sea level and up to 3000m above sea level
• Ordinary Equipment (enclosed equipment without protection against ingress of water): IP Rating: IPX0
• Equipment not suitable for use in the presence of a flammable anaesthetic mixture with air or with oxygen or nitrous oxide
• No sterilization or disinfection required
2 User Guide for the Platinum Series Sound Processor
Table of Contents
Platinum Series Sound Processor 5
Program Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Sensitivity Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Headpiece Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Dual Color LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Audible Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Auxiliary Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Headpiece & Cable 9
Universal Headpiece (UHP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
UHP Color Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Batteries & Battery Charger 11
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Battery Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Using the Car Charger Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Accessories 16
Carrying Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Extending the Life of Your Headpiece Cables . . . . . . . . . . . . . . . . . . . 18
Auxiliary Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Telecoil Pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Telephone Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Microphone Tester Earphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Other Battery-Powered Input Devices . . . . . . . . . . . . . . . . . . . . . . . 21
Using the Platinum Series Sound Processor 22
Getting Started - Quick Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Adjusting for Background Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Using the Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Troubleshooting Guide 24
No Sound Heard; No Response From User . . . . . . . . . . . . . . . . . . . . 24
User Hears Static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
User Hears Muffled or Distorted Sounds . . . . . . . . . . . . . . . . . . . . . . 24
Headpiece Falls Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Headpiece or Processor Gets Wet . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Performing a System Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Replacing Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
The Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Headpiece . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Troubleshooting Action Table . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Caring for Your Cochlear Implant System 31
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
User Guide for the Platinum Series Sound Processor 3
Processor Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Implant Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Electrostatic Discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Airport Security Metal Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
X-Ray Machines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Recommended System Operating and Storage Temperatures . . . . . . . . . 34
Guidance and Manufacturer’s Declaration 35
Compatibility Tables 39
Contact Us 40
Platinum Series Sound Processor
Your audiologist will demonstrate the adjustable controls of the Platinum Series
Sound Processor (PSP) and instruct you on appropriate settings .
4 User Guide for the Platinum Series Sound Processor
Figure 1: Platinum Series Sound Processor .
Program Control
The program control, on the left side of the control panel, is used to turn the processor on and off, to select one of three programs, and to test the headpiece microphone . The dots on the program selector represent different programs on the processor programmed by your audiologist . The single represents program
# 1, represents program # 2, and represents program # 3 . Your audiologist will determine how many programs are appropriate and instruct you on when to use each program . The position represents the headpiece microphone tester function detailed in the “Using the Platinum Series Sound Processor” section of this manual . The (o) position will turn the processor off .
Volume Control
The volume control, indicated by and located to the right of the program control, allows the user to adjust the loudness level of the processor . Turning the control to the left (toward the smaller end of the scale) decreases the volume .
Turning the control to the right (toward the larger end of the scale) increases the volume . The volume range (how soft to how loud the volume can be adjusted) is programmed for you by your audiologist .
During your programming session, the audiologist will program your processor so that the 12:00 position on the volume dial represents your most comfortable loudness level .
User Guide for the Platinum Series Sound Processor 5
Sensitivity Control
The sensitivity control indicated by and located to the right of the volume control, determines the quietest level of sound that will be picked up from the environment by the microphone . The sensitivity control is typically set at 12:00 for daily device use . Turning the control to the left decreases the sensitivity so that softer sounds are not picked up by the microphone . This may help eliminate background noise . Turning the control to the right increases the sensitivity so that softer or more distant sounds can be picked up by the microphone .
Headpiece Jack
The headpiece jack is located to the right of the sensitivity control . The headpiece cable, which connects the processor to the headpiece, is inserted here .
Dual Color LED Indicator
The LED (Light-Emitting Diode) indicator is a light located on the control panel adjacent to the headpiece jack that indicates three primary functions: battery charge status, lock status, and microphone/system status . Depending on the function, the
LED will illuminate with either a red or a green light .
Battery Charge Status
When the processor program control is turned from the off position (o) to positions , , or , the red LED indicator will blink as follows:
• 3-4 quick blinks indicate that the battery is fully charged.
• 2 quick blinks indicate that the battery is sufficiently charged to power the system.
• 1 quick blink indicates that the battery charge is nearly depleted.
To check the battery charge status while the processor is in operation, turn the processor off and then back on to any program position . The red LED indicator sequence will indicate the battery charge status .
Lock Status
Lock refers to the successful communication between the processor and implant .
When the processor program control is turned from the off (o) position to positions
, , or , and the battery charge sequence is complete, the red LED indicator begins to flash approximately once per second, indicating lock has not yet been achieved . Flashing will continue until the headpiece is properly positioned on the head . Flashing red will resume if there is any problem with communication or loss of lock between the processor and the implant .
6 User Guide for the Platinum Series Sound Processor
Microphone/System Status
When the battery and lock sequences are complete, microphone and system status can be verified . The green LED indicator will flicker in response to loud sounds presented near the microphone verifying that the microphone is receiving sound, that data is being transmitted to the implant, and that the processor is receiving information back from the implant . Increasing the sensitivity will cause the green
LED to flash in response to softer sounds, while decreasing the sensitivity will require more intense sounds for the LED to react . The green light is not expected to illuminate continuously during everyday use, especially if the user is in a quiet environment . Also, the green LED will not illuminate in response to sounds if your audiologist has disabled the Automatic Gain Control (AGC) program feature for the selected program position .
IntelliLink ™ Implant ID Safety Feature (CII/HiRes 90K™ only) or Processor Error
Condition
The IntelliLink safety feature checks the implant ID to make sure it is the correct one that is programmed for stimulation with the processor . A rapidly blinking red light will appear should you accidentally attempt to use the wrong processor or attempt to lock to the wrong implant in the case of bilateral implants . A rapidly blinking red light might alternatively indicate, in rare instances, that there is a processor error condition . If this should occur, first turn the processor to the off (o) position, remove and reconnect the battery, and turn the processor back on to the desired program or try another program position . If you are unable to resolve the problem, please contact your audiologist for additional troubleshooting .
Audible Alarm
The audible alarm is an optional feature that can be activated at the time of programming . It is designed primarily for children in order to alert parents and teachers when the system is not transmitting sound to the implant or the battery is near depletion . If the child’s headpiece falls off the head, the processor will begin to beep and the red LED will flash . When the child’s headpiece is replaced and data is again being transmitted successfully, the alarm will stop . Beeping when the headpiece is in place indicates a communication problem between the processor and implant . For more information, refer to the “Using the Platinum Series Sound
Processor” section of this manual . Additionally, when the battery is near depletion and cannot power the processor, the alarm will emit a slow beeping tone until the battery dies or is replaced .
User Guide for the Platinum Series Sound Processor 7
Auxiliary Jack
The auxiliary jack is located on the side of the processor near the control panel . The auxiliary microphone and telephone adapter provided with the system are connected here . This jack is also used to connect other external auditory input sources, such as battery-powered FM systems, MP3 players, television audio amplifiers or other assistive listening devices .
The Microphone Tester Earphones provided by AB are also connected here . When the program switch is in the position, these earphones allow a subjective listening assessment of the quality of the sound as it is received by the headpiece microphone .
Also, intermittencies in the headpiece cable may be detected . If a problem is noted, please refer to the “Using the Platinum Series Sound Processor” section of this manual .
Note: To use the auxiliary jack, the processor must contain a program set up for auxiliary input. Consult with your audiologist regarding the correct program position to use with auxiliary input.
Caution: Your PSP should be serviced only at AB. Do not attempt to open or repair the processor. Unauthorized opening of the processor will void the warranty.
Headpiece & Cable
Universal Headpiece (UHP)
Included in the headpiece is a coil that transmits sound signals and power to your implant . The headpiece also includes a magnet well, housing the necessary number of magnets to ensure your headpiece stays on throughout the day, and is covered by a Color Cap which snaps securely in place . The headpiece microphone picks up sound from your environment and transfers it to the sound processor via a detachable cable . Once the sound processor has converted the sound into electric signals, it sends the information to the implant via the cable and headpiece . The cables come in a variety of colors and lengths to suit your needs .
NOTE : We recommend that you do not add or remove magnets from the headpiece without first consulting your programming center.
The microphone in the headpiece is located behind the hole on the color cap . The jack that connects the cable to the headpiece is located at the bottom of the headpiece .
NOTE : Your headpiece should be serviced only at AB. Do not attempt to open or repair the headpiece base. Unauthorized opening of the headpiece base will void the warranty.
UHP Color Caps
WARNING: Small Parts Hazard: The UHP Color Caps, magnets and spacers may cause choking if swallowed.
Attaching the UHP Color Cap
• Align the color cap with your headpiece.
• Gently press the cap and headpiece together. The Color Cap will snap into place.
Removing the UHP Color Cap
• Insert the UHP Removal Tool into the slot above the headpiece cable connector.
• Gently push the tool straight back to lift the color cap as shown below.
8 User Guide for the Platinum Series Sound Processor
Figure 2: Removing the UHP Color Cap .
User Guide for the Platinum Series Sound Processor 9
Cable
The cable connects the headpiece to the processor and provides the pathway for relaying information between the internal and external components of the system .
Cables are available in multiple lengths and colors .
To attach the cable to the headpiece
1.
Hold the headpiece in one hand and the cable connector in the other hand .
2.
Push the cable connector firmly into the headpiece connector .
To attach the cable to the sound processor
1.
Hold the sound processor in one hand and the cable connector in the other hand .
2.
Push the cable connector firmly into the sound processor connector .
NOTE: Be sure the processor is turned off before removing the cable from the headpiece.
Batteries & Battery Charger
A Lithium Ion rechargeable battery or a compartment that accommodates three standard AA batteries powers your PSP .
When you are not using your processor, it should be turned off; otherwise, the battery will continue to drain .
NOTE: Remove the rechargeable battery or the AA battery compartment from the processor when it is not likely to be used for an extended period of time.
To prevent intermittent operation of the processor, the battery contacts on the rechargeable battery or battery compartment and on the processor should be kept free from dirt and dust . Gently clean the contacts with a hearing aid brush or dry cotton swab at least once a month .
If the rechargeable battery is dropped, inspect it for evidence of damage or cracking .
If any evidence of damage is seen, the battery should be replaced .
WARNING: Batteries may explode if disposed of in fire. To prevent injury or burns, do not allow metal objects, such as keys or coins, to contact or short circuit the battery terminals. Covers are provided for use when carrying rechargeable batteries or the AA battery compartment.
WARNING: Power supplies and battery chargers should be operated in an open area to ensure adequate airflow. While no injury cases have resulted, components may become hot during normal use or a fault condition.
If the device’s temperature results in discomfort or pain when touched, disconnect the power source and contact your local AB representatives.
Battery Replacement
To remove the rechargeable battery or AA battery compartment:
• Turn the processor off (o).
• Gently press and raise the release lever on the side of the processor.
10 User Guide for the Platinum Series Sound Processor
Figure 11: Battery Release Lever .
User Guide for the Platinum Series Sound Processor 11
• Slide the battery in the direction of the lever until it disconnects from the processor .
To insert the rechargeable battery or AA battery compartment:
• Locate the slide tracks on the underside of the processor and the top of the battery.
• Position the battery so the battery contact is toward the lever on the processor.
• Guide the battery into the tracks on the processor.
• Slide the battery onto the processor until it engages.
• Do not force the battery into the processor. The battery is designed to be inserted in only one direction .
To insert batteries into the AA battery compartment:
• Unsnap battery pack utilizing thumb recess on top of pack.
• When inserting AA (or LR06) batteries, make sure that the positive and negative contacts on the batteries are lined up correctly as noted on the label inside the battery compartment .
• Replace the cover by hooking the case together at the bottom and gently snapping it until closed .
• Insert the AA battery compartment using steps outlined above.
• When the AA battery compartment is not in use, keep it protected with the battery cover .
CAUTION: Do not attempt to operate your system with the rechargeable battery or AA batteries improperly inserted as it may damage the internal components of the processor.
NOTE: For proper disposal of rechargeable batteries in Europe, please return depleted batteries to the nearest local AB representative or the designated programming /follow-up center. In the United
States and Canada, please call the Rechargeable Battery Recycling
Corporation hotline at 800.822.8837 or visit their website at www.call2recycle.org.
Battery Charger
The battery charger provided with your processor is designed so that two lithium ion rechargeable batteries can be charged simultaneously . It is compatible with batteries provided with the AB Platinum Series Sound Processor and the S-Series Processor only . Batteries do not need to be fully depleted before recharging .
Figure 12: Battery Charger .
Light Emitting Diode (LED) Indicators:
A green LED below the power symbol on the battery charger illuminates when sufficient power is flowing to the unit . Each charger bay has a two color status LED .
The following table summarizes the different states of the LED:
LED Color Indication
Green
Red
Battery is fully charged or there is no battery in the charger bay .
Battery is being charged .
Blinking
Red Error Battery needs to be replaced .
Off No power or electrical overload (reset by removing the power connection from the charger and then reconnecting power) .
12 User Guide for the Platinum Series Sound Processor User Guide for the Platinum Series Sound Processor 13
To charge the lithium ion rechargeable batteries:
• Place charger on a flat surface.
• Connect the power supply cord to the power supply (use only AB-7610 or AB-
5620, Charger Car Adapter) . Connect the cable from the power supply to the charger . Plug power supply cord into power outlet .
Figure 13: Connecting the Power Supply to the Charger .
• Gently insert one or two rechargeable batteries in the charger so that the con tacts on each battery match up with the contacts in the charger . The charger is designed so that batteries will only insert in one direction .
CAUTION: The charger is only designed for use with the processor lithium ion rechargeable batteries provided by AB. Do not attempt to charge off-the-shelf batteries used inside the AA battery compartment.
The rechargeable batteries and charger contacts should be kept free from dirt and dust. Dirty contacts can result in charger malfunction.
Gently clean the contacts with a hearing aid brush or dry cotton swab being careful not to bend the contact pins. This should be done at least once a month.
If the charger is dropped, inspect the device for evidence of damage or cracking. If any evidence of damage is seen, the battery charger should be replaced. Prior to use, you should inspect the charger power cord to ensure that it is not frayed or damaged and that the plug is not broken. If your power cord appears to be damaged, it should be replaced.
Using the Car Charger Adapter
After inserting the car adapter (AB-5620) into your car’s power outlet, connect the cable from the car adapter to the charger .
Figure 14: Battery Charger with Battery .
• The batteries will start charging automatically.
• If a partially charged battery is placed in the charger, the battery may be fully charged in a shorter period of time . The battery can be removed at anytime .
The charger and batteries will not be damaged if the batteries are left in the charger longer than the required charging time (approximately 3 .5 hours) . It is a good idea to use the batteries on a rotating basis to maximize battery life .
Batteries can be labeled (e .g ., 1, 2, 3) to keep track of the rotation .
14 User Guide for the Platinum Series Sound Processor
Figure 15: Car Charger Adapter .
User Guide for the Platinum Series Sound Processor 15
Accessories
Carrying Cases
A variety of carrying cases are available for your processor . Pediatric Kits are packaged with a belt and harness case . Adult Kits come with a belt worn carrying case that is also available in additional colors and styles that can be purchased as accessories .
NOTE: Nylon carrying cases are hand washable in mild soap. Air dry only; do not machine dry.
Harness Case
A harness with an attached case allows the processor to be worn at the child’s side .
The harness is constructed of durable cotton and is adjustable . The attached case is lined with neoprene and constructed of lightweight cotton . The harness case is large enough to contain the processor with the control panel cover .
Control Panel Cover
The control panel cover helps prevent accidental adjustment of processor controls during activity . In addition, it provides protection from sand in play areas .
Leather Carrying Case
The belt worn leather carrying case secures the processor at the waist . A clip on the back of the case attaches it to your waistband or belt . Cable protector holes located near the belt clip extend the life of headpiece cables when used as illustrated on the following page . See Figures 18-20 .
Figure 17: Leather Carrying Cases .
Sport Carrying Case
A lined water-resistant case, which can be worn on the waist or a belt, is provided .
A flap secured with velcro folds over the top of the processor to protect the controls, and a clip on the back of the case secures it to your waistband . A belt loop on the case provides additional security for more physical activities . Cable protector holes located near the belt clip extend the life of headpiece cables when used as illustrated on the following page . See Figures 18-20 .
Figure 16: Platinum Series Harness Case .
16 User Guide for the Platinum Series Sound Processor User Guide for the Platinum Series Sound Processor 17
Extending the Life of Your Headpiece Cables
1 . Plug in the cable as shown .
Figure 18: Feeding the Cable .
2 . Feed the cable through the far buttonhole .
Figure 19: Feeding the Cable Through Far Buttonhole .
3 . Feed the cable through the other buttonhole .
Figure 20: Feeding the Cable Through Other Buttonhole .
18 User Guide for the Platinum Series Sound Processor
Auxiliary Microphone
You may find that using an auxiliary microphone (also called a lapel microphone) is preferable in some or all listening environments . The auxiliary microphone can be hand-held or worn on your lapel or collar . You may want to experiment with several microphone positions to find out which location is best for you .
To use the auxiliary microphone:
1 . Turn the processor off by turning the program switch to the off (o) setting .
2 . Plug the auxiliary microphone into the auxiliary jack located on the side of the processor .
3 . Place the microphone in a secure position using the cable clip provided .
4 . Turn the processor on by turning the program switch to , , or , depending on which program you want, and adjust the volume and sensitivity as necessary . To use the auxiliary microphone, the PSP must contain a program set up for auxiliary input .
5 . Turn your processor off prior to removing the auxiliary microphone .
When the auxiliary microphone is used, the microphone located in the headpiece may remain on or shut off depending on how your system is programmed by your audiologist . Please verify program setting with your audiologist to ensure the setting is appropriate for use with your auxiliary microphone .
IMPORTANT: Please consult with your audiologist or AB prior to using an auxiliary microphone purchased from a third-party vendor to determine if you have the appropriate cables and connectors and that the device in question is compatible with your system.
Telecoil Pickup
The telecoil pickup provides an interface to audio induction loop assistive listening systems, (e .g ., “room loops” and “neck loops”) and an alternative to placing the telephone receiver next to the microphone of the headpiece or auxiliary microphone .
To use the telecoil pickup, plug the connector of the pickup into the auxiliary jack on the side of the processor . For use with audio induction loops, position the telecoil pickup inside the perimeter of the audio loop . For use with a hearing aid compatible telephone, attach the suction cup to the earpiece of the telephone receiver . When using the telecoil pickup with a telephone having a textured (non-smooth) finish, it will be necessary to hold the telecoil pickup in place while using the telephone .
HINT: It may be necessary to move the telecoil pickup around the earpiece of the telephone receiver to find the best signal, or “sweet spot .”
User Guide for the Platinum Series Sound Processor 19
Telephone Adapter
The telephone adapter provides an alternative to placing the telephone receiver next to the microphone of the headpiece or auxiliary microphone .
Other Battery-Powered Audio Input Devices
In addition to the accessories that are provided with the your processor, you may want to use other external audio input devices . The same auxiliary jack that is used for the auxiliary microphone or telephone adapter can be used for other batterypowered external audio input sources such as FM systems or MP3 players . Consult with your audiologist regarding which program position should be used with auxiliary audio input devices .
WARNING: Only plug battery operated devices into the auxiliary jack. Do not use with devices that are running on AC power and are connected to the wall outlet power supply unless you are using an appropriate patch cable. Patch cables contain special electronic components.
A patch cable was not included in your kit. Interfacing to a device plugged directly into an electrical outlet, such as a television, could result in damage to your processor and also could deliver unpleasant sensations or sounds to you.
Please contact AB prior to using such a device to determine if you have the appropriate cables and connectors and that the device in question is compatible with your system.
Figure 21: Telephone Adapter .
Set up the telephone adapter as follows:
• Unplug the handset cord from the telephone base.
• Plug the short cord into the handset jack on the telephone base.
• Mount the unit in a convenient location with the adhesive pad.
• Plug the handset into the modular jack on the telephone adapter.
To use the telephone adapter, plug the long gray cable into the auxiliary jack on the side of the processor . Adjust your volume and sensitivity controls as needed .
NOTE: Only use the telephone adapter with phones that have the dial pad in the base. The adapter will not work with phones that have the dial pad in the handset.
Microphone Tester Earphones
The headpiece microphone tester earphones allow a subjective listening assessment of the quality of the sound as it is received by the headpiece microphone . Intermittencies in the headpiece cable can also be detected .
To use the microphone tester earphones, turn the program switch on the processor to the microphone tester ( ) position, plug connector of the earphones into the auxiliary jack on the side of the processor and place the earphones over your ears .
NOTE: Using the microphone tester earphones will disable the green LED, and the patient will not be able to hear through his/her cochlear implant system. The microphone tester earphones are provided in the pediatric
Platinum Series Sound Processor Kit or may be purchased through AB.
The microphone test should only be performed using the earphones supplied by AB to help ensure accurate sound evaluation.
20 User Guide for the Platinum Series Sound Processor User Guide for the Platinum Series Sound Processor 21
Using the Platinum Series Sound Processor
Getting Started – Quick Steps
In order to use your processor, follow the steps below:
1 . Verify that the processor program switch is in the off position (o) .
2 . Check that a charged battery or an AA battery pack has been correctly inserted onto the processor .
3 . Adjust the volume ( way to the left .
) so that the indicator notch on the control is all the
4 . Check the position of the sensitivity control ( on the control is at the 12:00 position .
) so that the indicator notch
5 . Check that the headpiece connector is properly plugged into the headpiece jack on the processor .
6 . Place the headpiece on your head over the implant .
7 . Turn the processor on by turning the program switch to the appropriate position
(as determined by your audiologist) . Note that the red LED indicator should blink 1-4 times to indicate the battery charge status .
8 . Verify that the red LED indicator on the processor stops flashing once successful communication or “lock” is established with the implant .
9 . Readjust the volume and sensitivity controls as necessary . Adjustment of the controls may vary throughout the day depending upon the listening environment .
WARNING: While no injury cases have resulted, components of the system may become hot during normal use or a fault condition. If a particular device’s temperature results in discomfort or pain, promptly remove the product and contact your local AB representatives.
IMPORTANT: Use only the processor that has been programmed especially for you.
Using a different processor, which has been loaded with a different program, may be ineffective in providing sound information or may cause physical discomfort.
Be sure to turn the processor off before removing the headpiece.
NOTE: Under limited circumstances, the cochlear implant system may cause interference with TV reception. Based on internal testing and field experience, there is no evidence that this interference causes safety-related hazards. Consult your programming center or AB for assistance.
WARNING: Small Parts Hazard: Parents and caregivers should be counselled that the Platinum Series System may contain small parts that could cause choking if swallowed.
22 User Guide for the Platinum Series Sound Processor
Adjusting for Background Noise
In some situations, background noise may interfere with your ability to hear clearly .
Background noise can be particularly distracting in situations where a large number of people are speaking at once or in a noisy environment . Decreasing the sensitivity of the processor by turning the sensitivity control toward the left may help eliminate some of the background noise . Using the auxiliary microphone may also be helpful .
Using the Telephone
Your clinician may recommend when it is appropriate to begin working with the telephone . The telephone can be used by placing the phone directly over the headpiece, over the auxiliary microphone, by using the telecoil pickup, or by using the telephone adapter .
Experiment with all modes of telephone communication . Be patient . Telephone communication with the implant often improves over time as one gains experience using the device . When using the telecoil pickup, the telephone handset must be hearing aid-compatible, meaning the phone has an electromagnetic coupling capacity .
Digital cellular phones: Using or being in close vicinity to someone using certain digital cellular phones may cause interference with the cell phone’s reception . If such interference occurs, you can turn off your processor or move a greater distance from the source . Before purchasing a digital cellular phone, you should evaluate whether or not interference is evident . No such interference has been noted with cellular phones using analog technology .
User Guide for the Platinum Series Sound Processor 23
Troubleshooting Guide
The following is a description of the most common problems you may encounter with your processor and solutions for addressing those problems . After trying the remedies below, if the problem persists, contact your programming center or AB for support .
No Sound Heard; No Response From User
• Ensure that the cable is inserted into the processor and the headpiece is properly positioned . Turn the processor off (o) and back to position , , or .
• If the red LED indicator:
- Does not blink or blinks once, replace the lithium ion battery or battery compartment with another fully-charged lithium ion battery or new AA batteries .
- Blinks quickly 2 to 4 times and then flashes continuously, replace the cable first and then headpiece if flashing continues .
- Blinks quickly 2 to 4 times, followed by 1 flash, no sounds are heard, replace the headpiece . If a headpiece is not available, use the auxiliary microphone with a program that is set up to allow auxiliary input and repeat the process .
- Blinks quickly 2 to 4 times, followed by 1 flash, green LED illuminates in response to loud speech at the site of the microphone, and sounds are heard, the system is functioning properly .
User Hears Static
• Ensure that the sensitivity control is properly set (12:00 position).
• Replace the cable.
• Check and clean battery contacts.
User Hears Muffled or Distorted Sounds
• Ensure that the sensitivity control is properly set (12:00 position).
• Ensure that nothing is covering the headpiece microphone opening.
• Check and clean battery contacts.
• Use the green LED, auxiliary microphone or microphone tester earphones to determine if a new microphone is needed for the headpiece .
24 User Guide for the Platinum Series Sound Processor
Headpiece Falls Off
• Use the cable clip to provide additional stability to prevent the headpiece from falling to the ground .
• If your headpiece frequently falls off during normal activities, it may indicate the need for a stronger magnet . Contact your programming center .
Headpiece or Processor Gets Wet
• Turn the processor off immediately.
• Remove headpiece.
• Remove power source.
• Contact your programming center or AB for further instructions.
IMPORTANT: Do not attempt to clean or dry the headpiece or processor. Do not use if exposure to fluids is suspected.
WARNING: If your system appears to be working, but you experience deterioration in the volume or the quality and clarity of sound, contact your audiologist as your processor may need to be reprogrammed.
CAUTION: Your processor should be serviced only at AB. Do not attempt to open or repair the processor. Do not continue to use the processor if any part of it is damaged. Unauthorized opening of the processor, or other equipment, will void the warranty and may compromise system performance.
User Guide for the Platinum Series Sound Processor 25
Performing a System Check
You can verify your system’s operating status in three simple steps:
Step 1) Check battery charge status .
Step 2)
Step 3)
Check lock status .
Check microphone and system status .
To assure the system’s overall proper functioning, perform all three steps . Once you get used to the steps, it takes less than one minute to complete a system check .
Step 1: Check Battery Charge Status
Turn the processor program control to the off (o) position and then to the desired program position , , or .
Next, observe the red LED indicator . The red LED light sequence will indicate the battery charge status, as:
• 3-4 quick blinks indicate that the battery is fully charged.
• 2 quick blinks indicate that the battery is sufficiently charged to power the system.
• 1 quick blink indicates that the battery charge is nearly depleted. The battery should be replaced .
Instructions on how to change the battery are provided later in this section .
Step 2: Check Lock Status
The term lock refers to the successful transmission of continuous signals between the processor, cable, headpiece and the implant across the skin .
To check the lock status, continue to observe the LED indicator . After the fast blinking battery test sequence, the red LED will continue to flash approximately once per second if the headpiece is not in its proper position over the implant .
Adjust the position of the headpiece over the implant until the red LED stops flashing (Note: If the audible alarm feature has been activated during programming, the alarm will beep once each second until proper lock status is achieved . The audible alarm feature is usually programmed to be active in young children who typically do not report interruptions in sound transmission) .
When the headpiece is properly positioned over the implant, the red LED will stop flashing . This signifies that the system is sending information correctly between the headpiece and the implant . If lock cannot be established, replace the cable or headpiece, as described later in this section . If the problem continues, contact your audiologist .
26 User Guide for the Platinum Series Sound Processor
Step 3: Microphone and System Status
When the battery and lock sequences are complete, the microphone and system status can be verified .
To check the microphone and system status, turn the program control to the desired program position .
Adjust the volume and sensitivity controls each to the 12:00 position .
Observe the green LED indicator as you snap your fingers or speak loudly near the microphone . The green light should illuminate with each snap of your fingers and with each syllable .
If the green light still does not illuminate, try using the auxiliary microphone and repeat the system check sequence steps 1-3, as just described . Successful verification of the microphone and system status with the auxiliary microphone would indicate that the headpiece needs to be replaced .
Note: The green LED will not light up when using a program with the AGC disabled. Check with your programming center regarding which program to use for assessing the microphone status.
Replacing Components
The three most common actions required to restore your processor to proper functioning are: (1) changing the lithium ion battery, (2) replacing the cable, and
(3) replacing the headpiece, as described below .
Lithium Ion Rechargeable Battery
The PSP is powered by a custom-designed, rechargeable lithium ion battery . An alternative battery compartment, accepting three AA (or LR06) batteries, can be used with the processor .
As described in “Performing a System Check,” Step 1, a depleted or nearly depleted rechargeable battery should be replaced with a fully-recharged battery by taking the following actions .
To Change the Lithium Ion Rechargeable Battery:
• Turn the program control to the off (o) position.
• Remove the used rechargeable battery by gently pressing and raising the release lever on the left side of the processor, while at the same time sliding the battery case toward the lever . Return the used rechargeable battery to the charger, according to the instructions in the “Batteries and Battery Charger” section found earlier in this user guide.
• Using another fully-charged lithium ion battery, align the slide track on the top of the replacement battery with the slide track on the underside of the processor .
• Guide the battery onto the processor slide track and slide the battery until it
User Guide for the Platinum Series Sound Processor 27
engages into place on the processor . Do not force the battery . It is designed to be inserted in only one direction; forcing may jam or damage the slide mechanism .
• Perform the system check sequence, Steps 1-3, as described at the beginning of this section .
To Replace the AA Battery Compartment:
• Unsnap the AA battery compartment utilizing the thumb recess on the top of the compartment .
• Insert AA batteries into the battery compartment, making sure that the positive and negative contacts are in the correct orientations, as labeled inside the cover .
• Replace the cover by hooking the case together at the bottom and gently snapping it closed .
• Align the slide track on the top of the replacement battery compartment with the slide track on the underside of the processor .
• Guide the battery compartment onto the processor slide track and slide until it engages into place on the processor . Do not force the battery compartment, it is designed to be inserted in only one direction . Forcing the battery compartment may jam or damage the slide mechanism .
• Perform the system check sequence, steps 1-3, as described in the beginning of this section .
The Cable
The cable transfers signals between the headpiece and the processor . At one end of the cable is a right-angle single-pin (coaxial) plug that is inserted into the headpiece jack . The jack is located at the top of the processor . At the other end of the cable is a straight single-pin (coaxial) plug that is inserted into the headpiece . A strain relief portion near the plug is designed to protect the cable from damage during handling .
To Replace the Cable:
• Turn the program control to the off (o) position.
• Remove the headpiece from the cable by holding the cable at its strain relief portion and gently pulling the cable away from the headpiece . Disconnect the cable from the processor .
• Insert the right-angle plug of the replacement cable into the headpiece jack on the processor, and insert the straight plug into the headpiece connector .
• Repeat the system check, steps 1-3. If the microphone function is not restored, reconnect the first cable, and replace the headpiece .
28 User Guide for the Platinum Series Sound Processor
Headpiece
To Replace the Headpiece:
• Turn the program control to the off (o) position.
• Remove the headpiece from the cable by holding the cable at its strain relief portion and gently pulling the cable away from the headpiece .
• Insert the cable into the replacement headpiece.
• Repeat the system check, steps 1-3.
NOTE: Be sure the processor is turned off before removing the headpiece cable.
When replacing the processor headpiece we recommend that you consult with your programming center to verify proper headpiece fitting and sound quality adjustment .
User Guide for the Platinum Series Sound Processor 29
PROBLEM
Troubleshooting Action Table
ACTION
During battery status check, no flash or only one flash is observed .
Red LED indicator continuously blinks at one-second intervals – and/or – audible alarm, if activated, sounds at one-second intervals .
Continuous rapid blinks of the red LED indicator .
(Indicates wrong processor in use or processor error condition .)
Green LED does not illuminate to loud speech near microphone .
• Replace rechargeable battery or AA battery pack.
• If there are no blinks after replacement, clean the contacts with a hearing aid brush or dry cotton swab .
• If problem continues, contact your cochlear implant center.
• Remove and re-lock headpiece with implant.
• Replace headpiece cable.
• If problem continues, report immediately to your cochlear implant center . You may need a new headpiece or reprogramming .
• Verify the correct processor is in use.
• In the case of 2 implants (bilateral user) verify the correct processor is locked with the correct left or right implant .
• Change program control to another program position.
• Remove, clean battery contacts and reconnect battery to processor.
• Try an alternate battery.
• Report problem to cochlear implant center.
• Recheck battery status. If okay, perform next step.
• Check sensitivity setting (12:00) or try increasing for assessment only .
• Plug in an auxiliary microphone. If LED lights, then replace headpiece .
• Plug the microphone tester earphones into the external input port of the processor and turn the function switch to mic test ( ) .
Please refer to “Using the Platinum Series Sound Processor” section for info on the microphone tester earphones .
• If problem continues, immediately report to your cochlear implant center .
User reports hearing no sound .
• Repeat the system check steps: 1. Battery charge status, 2. Lock status, 3 . Microphone/System status .
• Check processor and control settings.
• Try auxiliary mic.
• Try another program.
• If problem continues, immediately report to your cochlear implant center .
User reports hearing static .
• Ensure that the cable is inserted into the processor and that the headpiece is positioned properly on the user’s head .
• Turn the volume and sensitivity controls to the 12:00 positions.
• If user still reports “static,” replace the cable.
• Visually inspect the microphone for signs of debris or wear.
• If available, try an auxiliary microphone or alternate headpiece.
• Use the microphone tester earphones and the microphone tester function ( ) .
User reports that sounds are muffled or distorted .
• Confirm that no clothing or material is obstructing the microphone opening .
• Repeat the same steps as when static is reported.
30 User Guide for the Platinum Series Sound Processor
Caring for Your Cochlear Implant System
Although your processor has been designed and built to withstand daily wear and tear, care must be taken to protect both the implanted and external components of the system . For a detailed discussion of clinical results, warnings and precautions please refer to the package insert supplied separately . It is a good idea to carry your
Patient Identification Card with you at all times .
Cleaning
If necessary, the processor and headpiece can be cleaned with a slightly dampened cloth or tissue . Take care that water does not drip into any connectors or the microphone . Water should not be allowed inside either the processor or headpiece .
CAUTION: Immersion in water will damage the processor and headpiece
electronics.
To prevent intermittent operation of the processor, the battery contacts on the battery pack and on the processor should be kept free from dirt and dust . Clean the contacts at least once a month with a hearing-aid brush or dry cotton swab .
Processor Protection
Your processor contains advanced electronics that can be damaged . Care should always be taken when using or handling your device . If the processor is dropped, check it for proper functioning . If you suspect that the processor has been damaged, contact your cochlear implant center for a replacement . Additionally, the programming cable connector located on the underside of your processor should be kept free from dirt and dust, as well as contact with objects that may damage the connector .
Care should be taken to avoid the following:
• Dropping the processor.
• Leaving the processor any place where it can come in contact with water or moisture . Remember to remove the processor and headpiece when bathing, showering, or swimming .
• Exposing the processor, headpiece, and lithium ion batteries to extreme temperatures . Store lithium ion batteries in a cool location at or below normal room temperature .
• Exposing the headpiece to organic vapors such as those produced by petroleum based products .
User Guide for the Platinum Series Sound Processor 31
To maintain and improve the life of the headpiece microphone we recommend that you store your headpiece in a Dry Aid kit overnight or when not in use . A Dry Aid kit is available separately for purchase from AB and other sources . While the processor has been built to be as sturdy as possible, it should be treated with gentle care and attention . Additionally, you should check your cable regularly (every week or so) to see if it is frayed or damaged . Avoid making sharp bends or kinks with the cable . If your cable appears to be damaged, it should be replaced .
Implant Protection
The implant is capable of withstanding the effects of running, exercise and normal activity . Regardless of the activity, precautions must be taken in order to avoid a blow to the head, which could damage the implanted device resulting in device failure .
WARNING: When engaging in physical activities that include the possibility of trauma or impact, extra precautions should be taken, such as using a protective helmet, to reduce the risk of damage to the implant.
Contact sports in which blows to the head or impa ct at the implant site are likely to occur should be avoided. If it is suspected that the device has been damaged, contact your audiologist.
Electrostatic Discharge
Your processor and its attachments are designed to withstand most static events without damage or interruption to your programs . However, there is a chance that high levels of static electricity will generate extreme electrostatic discharge events that may damage electronic components . Therefore, care should be taken to avoid exposing the headpiece, cables or sound processor to situations in which high levels of static electricity are created .
Electrostatic Discharge (ESD) is present when you feel a spark jump from your body .
ESD events are more likely to occur in very dry or cold environments . ESD events are less common in humid areas .
High levels of electrostatic charge are known to build up under the following circumstances:
• Walking on carpets
• Sliding on plastic slides
• Exiting an automobile
• Pulling sweaters on and off
• Touching TV or computer screens
• Removing bedding materials
32 User Guide for the Platinum Series Sound Processor
You should take the following basic precautions in order to reduce the chances of an
ESD event:
• Electrostatic potential can be safely reduced by touching any person or object with your fingers prior to contact with a headpiece, cables or sound processor . Hand contact will safely equalize electric charge and prevent sparks from jumping to the processor system . When approached by someone (for example on carpet), touch him or her first with your hand prior to them touching your external components . Parents are advised to touch their child before they touch a headpiece or sound processor that their child is wearing . Also, before placing any part of a processor system on a table or other surface, you should first touch the surface .
• Avoid contact between your processor/cables/headpiece and metal surfaces be fore you touch the metal surface with your hand . Children should remove their headpiece and processor before engaging in activities that commonly create static electricity, such as playing on plastic play equipment .
• Carefully exit motor vehicles, particularly in dry, cold weather. Try to avoid contact between processor system components and any vehicle metal as you exit .
• When possible, remove your external equipment prior to removing sweaters.
• The screens of televisions and computer monitors are highly charged. Contact is a problem for two reasons: First, the charge on screens can cause sparks .
Second, brushing or touching a screen can transfer a charge that will then discharge when you come in contact with another object or person . Do not touch
TV or computer screens .
• Use fabric softener when washing clothes and bedding, this will reduce the likelihood of charge generation . If you strip a bed while wearing a processor system, please remember to use your hands to safely reduce any charge buildup you may have acquired .
REMEMBER: “Touch with hands first!”
Airport Security Metal Detectors
Metal detectors and security scanners will not damage your implant . However, the implant system may activate the detector alarm as you pass through a security metal detector . Remember to carry your Patient Identification Card with you at all times . You might also hear a distorted sound caused by the magnetic field around the security scanner door or hand-held screening wand . Turning down the volume on your Processor before passing through security screening will ensure that those sounds, if they occur, are not too loud or uncomfortable .
User Guide for the Platinum Series Sound Processor 33
X-Ray Machines
X-Ray machines will not damage the implant but may damage the headpiece microphone . Avoid placing the headpiece in checked or carry-on baggage that is screened with x-rays . During airport security screening, the headpiece should either be worn through the metal detector or be hand-examined .
Recommended System Operating and Storage Temperatures
Table: Operating and storage temperature ranges
Condition
Operating temperature
Storage temperature
Minimum
0°C (32°F)
-20°C (-4°F)
Maximum
45°C (115°F)
55°C (131°F)
The Platinum Series system meets the temperature safety requirements of IEC
60601-1:2005 in ambient temperatures up to 33˚C .
Guidance and Manufacturer’s Declaration
Per IEC 60601-1-2
Table 1: Guidance and Manufacturer’s Declaration-Electromagnetic emissions
Guidance and manufacturer’s declaration –electromagnetic emissions
The Platinum Series system is intended for use in the electromagnetic environment specified below . The customer or the user of the Platinum Series system should assure that it is used in such an environment .
Emissions test Compliance Electromagnetic environment - guidance
RF emissions
CISPR 11
Group 1
The Platinum Series system uses RF energy only for its internal function .
Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment .
RF emissions
CISPR 11
Harmonic emissions
IEC 61000-3-2
Voltage fluctuations/ flicker emissions
IEC 61000-3-3
Class B
Not applicable
Not applicable
The Platinum Series system is suitable for use in all establishments, including domestic establishments and those directly connected to the public lowvoltage power supply network that supplies buildings used for domestic purposes .
34 User Guide for the Platinum Series Sound Processor User Guide for the Platinum Series Sound Processor 35
Table 2: Guidance and Manufacturer’s Declaration-Electromagnetic immunity
Guidance and manufacturer’s declaration – electromagnetic immunity
The Platinum Series system is intended for use in the electromagnetic environment specified below . The customer or the user of the Platinum Series system should assure that it is used in such an environment .
Immunity test IEC 60601 Compliance level a Electromagnetic test level environment - guidance
Electrostatic discharge (ESD)
IEC 61000-4-2
± 6 kV contact
± 8 kV air
± 6 kV contact
± 8 kV air
Power frequency
(50/60 Hz)
Magnetic Field
IEC 61000-4-8
Radiated RF
IEC 61000-4-3
3 A/m
3 V/m
80 MHz to 2 .5
GHz
3 A/m
3 V/m
Note 1: These guidelines may not apply in all situations . Electromagnetic propagation is affected by absorption and reflection from structures, objects, and people .
a . Essential performance of the Platinum Series system per IEC 60601 requirements is defined as auditory stimulation within safe amplitudes .
b . Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio,
AM and FM radio broadcast, and TV broadcast cannot be predicted theoretically with accuracy .
To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered . If the measured field strength in the location in which the Platinum
Series system is used exceeds the applicable
RF compliance level above, the Platinum Series systems should be observed to verify normal operation .
c . Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m .
Floors should be wood, concrete or ceramic tile . If floors are covered with synthetic material, the relative humidity should be at least 30 % .
Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment .
Portable and mobile RF communications equipment should be used no closer to any part of the
Platinum Series system, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter .
Recommended separation distance d = 1 .2
√ P < 800 MHz d = 2 .3
√ P ≥ 800 MHz where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in metres (m) . Field strengths from fixed
RF transmitters, as determined by an electromagnetic site survey, b should be less than the compliance level in each frequency range .
c
Interference may occur in the vicinity of equipment marked with the following symbol:
Table 3: Guidance and Manufacturer’s Declaration- Separation distances between
RF communications equipment and Platinum Series system
Recommended separation distances between portable and mobile
RF communications equipment and the Platinum Series system
The Platinum Series system is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled . The customer or the user of the Platinum Series system can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the Platinum Series system as recommended below, according to the maximum output power of the communications equipment .
Rated maximum output power of transmitter
(W)
0 .01
Separation distance according to frequency of transmitter
(m)
d = 1 .2
√ P < 800 MHz d = 2 .3
√ P ≥ 800 MHz
0 .12 0 .23
0 .1
1
0 .38
1 .2
0 .73
2 .3
10
100
3 .8
12
7 .3
23
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer .
Note 1: These guidelines may not apply in all situations . Electromagnetic propagation is affected by absorption and reflection from structures, objects and people .
36 User Guide for the Platinum Series Sound Processor User Guide for the Platinum Series Sound Processor 37
Table 4: Platinum Series External Equipment and Accessories
The following table details the Platinum Sound Processor and its compatible hardware parts with the corresponding Advanced Bionics model number . Advanced
Bionics supplies a range of accessories for use with the Platinum Sound Processor, although not all accessories may be included in your sound processor kit or listed here . For additional information regarding the Platinum Sound Processor or its accessory parts, contact your clinician or Advanced Bionics .
Model Number
AB-7250*
AB-7500*
AB-7510*
AB-7600
AB-7610**
AB-7620, AB-7630, or
AB-7640
AB-7420-XX
AB-7440-XX
AB-7660-XX
AB-7750
CI-5305*
CI-5412-XXX*
AB-5620
Description
Platinum Sound Processor
Rechargeable Battery Pack
AA Battery Compartment
Battery Charger
Battery Charger Power Supply
Power Supply Cord
Leather Carrying Case
Harness
Sport Case
Telecoil Pickup Coil
Headpiece
Headpiece Cables
Battery Charger Car Adapter
*Applied part per IEC 60601-1
**Class I device: Warning: To avoid risk of electric shock, this equipment must only be connected to a supply mains with protective earth .
Note: The Xs denote model number variants related to product color and/or length .
Table 5: Technical Information
PSP
Processor
Battery
Charger
Rated
Voltage
3.1 - 4.5 V DC
12 V
Type
DC
Rated
Current
600 m
A
900 m
A
Power Source
Rechargeable Battery Pack
AA Battery Case
Programming Interface
Battery Charger Power Supply
Battery Charger Car Adapter
38 User Guide for the Platinum Series Sound Processor
Compatibility
The following tables display the compatibility between products in the HiResolution™
Bionic Ear System family and/or previous generation product .
Table 1
Implant Type
-
C1
Neptune™
Harmony™ ✓ 2
Auria™ -
Platinum Sound Processor (PSP) ✓ 4
1 Requires SoundWave™ 2 .1 or later
2 Requires SoundWave 2 .0 or later
3 Requires SoundWave 1 .4 or later
4 Requires SClin2000
✓
✓
CII
✓ 1
✓ 3
✓
✓
HiRes 90K
✓ 1
✓ 3
Table 2
SClin2000
SoundWave (versions 1.x)
Implant Type
C1 CII
✓ ✓
✓
SoundWave 2.0
SoundWave 2.1
1 Only on Harmony
✓
✓
1
1
✓
✓
-
HiRes 90K
✓
✓
✓
Table 3
Universal Headpiece
(UHP)
AquaMic
HR 90K Auria Headpiece -
Platinum Headpiece -
Processor Type
Neptune Harmony Auria PSP
✓ ✓ ✓ ✓
✓ -
✓
✓
-
✓
✓
-
-
✓
User Guide for the Platinum Series Sound Processor 39
Contact Us
Advanced Bionics is committed to providing the highest quality products and service to our customers . We welcome your comments regarding the Platinum Series
Sound Processor or your suggestions to improve our products . Please feel free to contact Advanced Bionics or discuss your suggestions with your implant professional .
Advanced Bionics AG
Laubisrütistrasse 28, 8712 Stäfa, Switzerland
T: +41 .58 .928 .78 .00 F: +41 .58 .928 .78 .90 [email protected]
Manufactured by:
Advanced Bionics LLC
28515 Westinghouse Place, Valencia, CA 91355, United States
T: +1 .877 .829 .0026 T: +1 .661 .362 .1400 F: +1 .661 .362 .1500 [email protected]
For additional contact information, please visit AdvancedBionics.com
Advanced Bionics, Platinum Series™, HiResolution™, HiRes 90K™, Neptune™,
Harmony™, Auria™, Built Kid Tough™ and IntelliLink™ are trademarks of Advanced
Bionics in the United States of America and other countries .
029-M296-03 Rev B
40 User Guide for the Platinum Series Sound Processor

Public link updated
The public link to your chat has been updated.
Advertisement