IECEE-CMC/ /Q

IECEE-CMC/ /Q
Ref. Certif. No.
KR-KETI1926
IEC SYSTEM FOR MUTUAL RECOGNITION OF TEST
CERTIFICATES FOR ELECTRICAL EQUIPMENT (IECEE)
CB SCHEME
SYSTEME CEI D’ACCEPTATION MUTUELLE DE
CERTIFICATS D’ESSAIS DES EQUIPEMENTS
ELECTRIQUES (IECEE) METHODE OC
CB TEST CERTIFICATE
Product
Produit
Name and address of the applicant
Nom et adresse du demandeur
Name and address of the manufacturer
Nom et adresse du fabricant
Name and address of the factory
Nom et adresse de l’usine
Note: When more than one factory, please report on page 2
Note: Lorsque il y plus d'une usine, veuillez utiliser la 2ème page
CERTIFICAT D’ESSAI OC
Video Recorder
SHENZHEN ANKO TECH CO., LTD.
NO. A1514, YUANZHENG INDUSTRIAL PARK, WUHE
DADAO BEI, BANTIAN, LONGGANG ZONE, SHENZHEN
CITY, CHINA
SHENZHEN ANKO TECH CO., LTD.
NO. A1514, YUANZHENG INDUSTRIAL PARK, WUHE
DADAO BEI, BANTIAN, LONGGANG ZONE, SHENZHEN
CITY, CHINA
SHENZHEN ANKO TECH CO., LTD.
NO. A1514, YUANZHENG INDUSTRIAL PARK, WUHE
DADAO BEI, BANTIAN, LONGGANG ZONE, SHENZHEN
CITY, CHINA
Additional Information on page 2
Ratings and principal characteristics
Valeurs nominales et caractéristiques principales
DC 12V, 5A for 5816 (See page 2 For details)
Trademark (if any)
Marque de fabrique (si elle existe)
ANKO
Type of Manufacturer's Testing Laboratories used
Type de programme du laboratoire d'essais constructeur
Model / Type Ref.
Ref. De type
Additional information (if necessary may also be reported
on page 2)
Les informations complémentaires (si nécessaire,, peuvent
être indiqués sur la 2ème page
A sample of the product was tested and found
to be in conformity with IEC
Un échantillon de ce produit a été essayé et a été
considéré conforme à laCEI
As shown in the Test Report Ref. No. which forms part of
this Certificate
Comme indiqué dans le Rapport d’essais numéro de
référence qui constitue partie de ce Certificat
5616, 5808, 5404, 5832, 5816, 6204, 6209, 6216, 6225,
6232
Additional Information on page 2
IEC 60065:2001 (Seventh Edition) + A1:2005 + A2:2010
W14-65-007
This CB Test Certificate is issued by the National Certification Body
Ce Certificat d’essai OC est établi par l’OrganismeNational de Certification
Korea Testing Certification (KTC)
24, 1gil, Sebang-Cheon, Gunpo-City, Gyeonggi-Do, 435-862,
KOREA, REPUBLIC OF
Date: 2014. 01. 27
Issued 2009-03
Signature:Seung-In Yang
1/2
Ref. Certif. No.
KR-KETI1926
Ratings :
Model
5616
5808
5404
5832
5816
6204
6209
6216
6225
6232
Rating
DC 12V, 4A
DC 12V, 3A
DC 12V, 3A
DC 12V, 6A
DC 12V, 5A
DC 12V, 3A
DC 12V, 4A
DC 12V, 5A
DC 12V, 5A
DC 12V, 6A
Video input channel
16
8
4
32
16
4
9
16
25
32
Additional information (if necessary)
Information complémentaire (si nécessaire)
Korea Testing Certification (KTC)
24, 1gil, Sebang-Cheon, Gunpo-City, Gyeonggi-Do, 435-862,
KOREA, REPUBLIC OF
Date: 2014 01.27
Issued 2009-03
Signature:Seung-In Yang
2/2
Test Report issued under the responsibility of:
Korea Testing Certification
TEST REPORT
IEC 60065
Audio, video and similar electronic apparatus - Safety requirements
Report Number. .............................. :
W14-65-007
Date of issue ................................... :
2014-01-25
Total number of pages ................... :
28 pages
Applicant’s name ............................ :
SHENZHEN ANKO TECH CO., LTD.
Address ........................................... :
NO. A1514, YUANZHENG INDUSTRIAL PARK, WUHE DADAO
BEI, BANTIAN, LONGGANG ZONE, SHENZHEN CITY, CHINA
Test specification:
Standard .......................................... :
IEC 60065:2001 (Seventh Edition) + A1:2005 + A2:2010
Test procedure ............................... :
CB Scheme
Non-standard test method ............ :
N/A
Test Report Form No. .................... :
IEC60065K
Test Report Form(s) Originator .... :
Intertek Semko AB
Master TRF ...................................... :
Dated 2010-10
Copyright © 2010 Worldwide System for Conformity Testing and Certification of Electrotechnical
Equipment and Components (IECEE), Geneva, Switzerland. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as
copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from
the reader's interpretation of the reproduced material due to its placement and context.
If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB
Scheme procedure shall be removed.
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and
appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
Test item description ..................... : Video Recorder
Trade Mark ...................................... : ANKO
Manufacturer................................... : SHENZHEN ANKO TECH CO., LTD.
Model/Type reference .................... : 5616, 5808, 5404, 5832, 5816, 6204, 6209, 6216, 6225, 6232
Ratings ............................................ : DC 12V, 5A for 5816
(See page 6 For details)
Korea Testing Certification
Page 2 of 28
Report No.: W14-65-007
Testing procedure and testing location:
CB Testing Laboratory:
Korea Testing Certification
Testing location/ address ........................ : 24, 1gil, Sebang-Cheon, Gunpo-City, Gyeonggi-Do, 435862, KOREA, REPUBLIC OF
Associated CB Laboratory:
Testing location/ address ........................ :
Tested by (name + signature) ....... :
Y.J.KIM
Approved by (name + signature) .. :
B.Y.CHOI
Testing procedure: TMP
Testing location/ address ........................ :
Tested by (name + signature) ....... :
Approved by (name + signature) .. :
Testing procedure: WMT
Testing location/ address ........................ :
Tested by (name + signature) ....... :
Witnessed by (name + signature) . :
Approved by (name + signature) .. :
Testing procedure: SMT
Testing location/ address ........................ :
Tested by (name + signature) ....... :
Approved by (name + signature) .. :
Supervised by (name + signature) :
Testing procedure: RMT
Testing location/ address ........................ :
Tested by (name + signature) ....... :
Approved by (name + signature) .. :
Supervised by (name + signature) :
TRF No. IEC60065K
Korea Testing Certification
Page 3 of 28
Report No.: W14-65-007
List of Attachments (including a total number of pages in each attachment):
1. Attachment 1: Photograph (4 pages)
Summary of testing:
Tests performed (name of test and test clause): Testing location:
Cl. 4.2 Input test
Korea Testing Certification
Cl. 7.1 Temperature Test
24, 1gil, Sebang-Cheon, Gunpo-City, Gyeonggi-Do,
435-862, KOREA, REPUBLIC OF
Cl. 4.2, 4.3, 11.1, 11.2 Abnormal Test
Cl. 17.1 Torque test
Summary of compliance with National Differences
List of countries addressed:
Group differences, special national deviations of all CENELEC countries, AR, AU, CA, JP, KR, MY and
US.
Explanation of CENELEC countries: Austria (AT), Belgium (BE), Bulgaria (BG), Croatia (HR), Cyprus
(CY), Czech Republic (CZ), Denmark (DK), Estonia (EE), Finland (FI), France (FR), Germany (DE),
Greece (GR), Hungary (HU), Iceland (IS), Ireland (IE), Italy (IT), Latvia (LV), Lithuania (LT), Luxembourg
(LU), Malta (MT), Netherlands (NL), Norway (NO), Poland (PL), Portugal (PT), Romania (RO), Spain (ES),
Slovakia (SK), Slovenia (SI), Sweden (SE), Switzerland (CH) and United Kingdom (GB).
Explanation of used codes for National Differences: Argentina (AR), Australia (AU), Canada (CA), Japan
(JP), Korea (KR), Malaysia (MY) and United States of America (US).
All country differences listed in the CB Bulletin are covered by the Common Modifications, Special
National Conditions, National Deviations, and National Requirements noted above except for the following
countries which are documented in Country Differences. Attachments attached to this report: refer to
appendix 1 for details.
Compliance with the National requirements of “(countries)” as given in CB Bulletin “(112A)” dated
December 2006 and IECEE website dated January 2011 were also confirmed.
The product fulfils the requirements of IEC 60065:2001 + A1:2005 + A2:2010 and
EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011
TRF No. IEC60065K
Korea Testing Certification
Page 4 of 28
Report No.: W14-65-007
Copy of marking plate
The artwork below may be only a draft. The use of certification marks on a product must be
authorized by the respective NCBs that own these marks.
Video Recorder
Model: ANKO
Rating: DC 12V, 5A
SHENZHEN ANKO TECH CO., LTD.
TRF No. IEC60065K
Korea Testing Certification
Page 5 of 28
Report No.: W14-65-007
Test item particulars………………………………….: Video Recorder
Classification of installation and use......................: Transportable apparatus
Supply Connection……………………………………: Not direct connceted to a mains supply
Possible test case verdicts:
- test case does not apply to the test object............ : N/A (Not Applicable)
- test object does meet the requirement .................. : P (Pass)
- test object does not meet the requirement ........... : F (Fail)
Testing:
Date of receipt of test item ......................................... : 2013-12-16
Date (s) of performance of tests................................ : 2013-12-16 to 2014-01-23
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(see Enclosure #)" refers to additional information appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a
comma /
point is used as the decimal separator.
Manufacturer’s Declaration per sub-clause 6.2.5 of IECEE 02:
The application for obtaining a CB Test Certificate
includes more than one factory location and a
declaration from the Manufacturer stating that the
sample(s) submitted for evaluation is (are)
representative of the products from each factory
has been provided ...................................................... :
Yes
Not applicable
When differences exist; they shall be identified in the General product information section.
Name and address of factory (ies) .......................... : SHENZHEN ANKO TECH CO., LTD.
NO. A1514, YUANZHENG INDUSTRIAL PARK,
WUHE DADAO BEI, BANTIAN, LONGGANG ZONE,
SHENZHEN CITY, CHINA
General product information:
1. The product is a Video Recorder.
2. The enclosures fixed together by screws and mechanical fixing.
3. The equipment is portable equipment with Class III construction.
4. Clearance was evaluated for altitude up to 2000m above sea level.
5. The maximum operating temperature is 35℃.
4. All the models have the same constructions and operate general principle. Except the model number and
video input channel. Due to the similarity between models, the model 5816 was selected for full tests.
TRF No. IEC60065K
Korea Testing Certification
Page 6 of 28
Details:
Model
5616
5808
5404
5832
5816
6204
6209
6216
6225
6232
TRF No. IEC60065K
Rating
DC 12V, 4A
DC 12V, 3A
DC 12V, 3A
DC 12V, 6A
DC 12V, 5A
DC 12V, 3A
DC 12V, 4A
DC 12V, 5A
DC 12V, 5A
DC 12V, 6A
Video input channel
16
8
4
32
16
4
9
16
25
32
Report No.: W14-65-007
Korea Testing Certification
Page 7 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
3
General requirements
Safety class of the apparatus ................................. :
4
General test conditions
4.1.4
Ventilation instructions require the use of the test box
5
Marking and instructions
5.1
5.2
5.3
Result - Remark
Verdict
--
Class III, suoolied by SELV
circuit
N/A
-Yes
P
--
Comprehensible and easily discernible
Compliance checked
P
Permanent durability against water and petroleum
spirit
After rubbing test by water
and petroleum spirit, the
marking still legible; it is not
easily possible to remove
the marking plate and show
no curling
P
a) Identification, maker ............................................ :
SHENZHEN ANKO TECH
CO., LTD.
P
b) Model number or type reference .......................... :
See rated label on page 4.
P
c) Class II symbol if applicable ................................ :
Class III
d) Nature of supply.................................................... :
DC
P
e) Rated supply voltage ........................................... :
12V
P
N/A
f) Mains frequency if safety dependant .................... :
N/A
g) Rated current or power consumption for apparatus
supplied by supply apparatus for general use ......... :
P
Measured current or power consumption ................ :
(see appended table 7.1)
P
Deviation % (max 10%) ........................................... :
(see appended table 7.1)
P
h) Rated current or power consumption for apparat-us
intended for connection to an a.c. mains supply ...... :
N/A
Measured current or power consumption ................ :
N/A
Measured current or power consumption for Television
set ............................................................................. :
N/A
Deviation % (max 10%) ........................................... :
N/A
a) Earth terminal
N/A
b) Hazardous live terminals
No hazardous live terminal
was accessible
N/A
c) Markings on supply output terminals
No such terminals
N/A
a) Use of triangle with exclamation mark
N/A
b) marking on loudspeaker grille, IEC 60417-5036
N/A
TRF No. IEC60065K
Korea Testing Certification
Page 8 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
Result - Remark
5.4
Instructions for use
English user manual
specified instruction for use
and maintenance
5.4.1
a) Mains powered equipment not exposed to dripping
or splashing. Warning concerning objects filled with liq
uid, etc.
b) Hazardous live terminals, instructions for wiring
No hazardous live terminal
N/A
c) Instructions for replacing lithium battery
No lithium battery within the
EUT
N/A
N/A
e) Instructions for multimedia system connection
P
f) Special stability warning for attachment of the
apparatus to the floor/wall
N/A
g) Warning: battery exposure to heat
No such construction
N/A
h) Warning: protective film on CRT face
No such device within the
EUT
N/A
a-b) Disconnect device: plug/coupler or all-pole mains
switch location, accessibility and markings
The EUT is supplied by
external approved adapter
N/A
c) Instructions for permanently connected equipment
The EUT is not such
apparatus
N/A
Marking, signal lamps or similar for completely
disconnection from the mains
No such marking within the
EUT
N/A
6
Hazardous radiation
6.1
Ionizing radiation < 36 pA/kg (0,5 mR/h)
-No ionizing radiation
Ionizing radiation under fault condition
6.2
P
N/A
d) Class I earth connection warning
5.4.2
Verdict
N/A
N/A
Laser radiation, emission limits to IEC 60825-1 ..... :
No laser radiation
N/A
Emission limits under fault conditions .................... :
See above
N/A
7
Heating under normal operating conditions
7.1
Temperature rises not exceeding specified values, no
operation of fuse links
(see appended table)
P
7.1.1
Temperature rise of accessible parts
(see appended table)
P
7.1.2
Temperature rise of parts providing electrical
insulation
(see appended table)
P
7.1.3
Temperature rise of parts acting as a support or as a
mechanical barrier
N/A
7.1.4
Temperature rise of windings
N/A
7.1.5
Parts not subject to a limit under 7.1.1 to 7.1.4
TRF No. IEC60065K
--
(see appended table)
P
Korea Testing Certification
Page 9 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
Result - Remark
7.2
Softening temperature of insulating material
supporting parts conductively connected to the mains
o
carrying a current > 0,2 A at least 150 C
The apparatus is supplied
from extermal power
adapter with DC 12V.
8
Constructional requirements with regard to the protection against electric
shock
8.1
Conductive parts covered by lacquer, paper, untreated Class III appliance
textile oxide films and beads etc. considered to be
bare
N/A
8.2
No shock hazard when changing voltage setting
device, fuse-links or handling drawers etc.
No such components are
replaced by hand
N/A
8.3
Insulation of hazardous live parts not provided by
hygroscopic material
No hygroscopic material
used
N/A
8.4
No risk of electric shock following the removal of a
cover which can be removed by hand
The EUT is complied with
the requirements
N/A
8.5
Class I equipment
Class III
N/A
8.6
Verdict
N/A
--
Basic insulation between hazardous live parts and
earthed accessible parts
N/A
Resistors bridging basic insulation complying with
14.1 a)
N/A
Capacitors bridging basic insulation complying with
14.2.1 a)
N/A
Protective earthing terminal
N/A
Class II equipment and Class II constructions within
Class I equipment
Only SELV circuit within the
EUT
N/A
Double or reinforced insulation between hazardous
live parts and accessible parts
N/A
Components bridging reinforced or double insulation
complying with 14.1 a) or 14.3
N/A
Basic insulation bridged by components complying
with 14.3.4.3
N/A
Basic and supplementary insulation each being
bridged by a capacitor complying with 14.2.1 a)
N/A
Double or reinforced insulation being bridged with 2
capacitors in series complying with 14.2.1 a)
N/A
Double or reinforced insulation being bridged with a
single capacitor complying with 14.2.1 b)
N/A
8.7
This clause is void
8.8
Basic or supplementary insulation > 0,4 mm (mm) :
N/A
Reinforced insulation > 0,4 mm (mm) .................... :
N/A
Think sheet insulation (excluding non-separable thin
sheet insulation. See 8.22)
N/A
TRF No. IEC60065K
--
Korea Testing Certification
Page 10 of 28
Report No.: W14-65-007
IEC 60065
Clause
8.9
8.10
8.11
Requirement – Test
Result - Remark
Verdict
Basic or supplementary insulation, at least two layers,
each meeting 10.3
N/A
Basic or supplementary insulation, three layers any
two of which meet 10.3
N/A
Reinforced insulation, two layers each of which meet
10.3
N/A
Reinforced insulation, three layers any two which meet
10.3
N/A
Adequate insulation between internal hazardous live
conductors and accessible parts
N/A
Adequate insulation between internal hazardous live
parts and conductors connected to accessible parts
N/A
Double insulation between conductors connected to
the mains and accessible parts.
N/A
Double insulation between internal hazardous live
parts and conductors connected to accessible parts.
N/A
Detaching of wires
N/A
No undue reduction of creepages or clearance
distances if wires become detached
N/A
Vibration test carried out ......................................... :
N/A
8.12
This clause is void
--
8.13
Adequate fastening of windows, lenses, lamp covers
etc. (pull test 20 N for 10 s)
N/A
8.14
Adequate fastening of covers (push/pull test 50 N for
10 s)
N/A
8.15
No risk of damage to the insulation of internal wiring
due to hot parts or sharp edges
N/A
8.16
Only special supply equipment can be used
N/A
8.17
Insulated winding wire without additional interleaved
insulation
N/A
8.18
Endurance test as required by 8.17
See above
N/A
8.19
Disconnection from the mains
The EUT is supplied by an
external adapter
N/A
8.19.1
Disconnect device
N/A
All-pole switch or circuit breaker with >3mm contact
separation
N/A
8.19.2
Mains switch ON indication
Mark “I” for switch on and
“O” for switch off
P
8.20
Switch not fitted in the mains cord
No mains switch is fitted in
the mains cord
P
8.21
Bridging components comply with clause 14
No such component used to
bridge
TRF No. IEC60065K
N/A
Korea Testing Certification
Page 11 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
Result - Remark
Verdict
8.22
Non-separable thin sheet material
No such material
N/A
9
lectric shock hazard under normal operating conditions
9.1
Testing on the outside
9.1.1
For voltages >1000 V ac or >1500 V dc complies
with clause 13.3.1 for basic insulation
9.1.1.1
a) Open circuit voltages
N/A
b) Touch current measured from terminal devices
using the network in annex D ................................. :
N/A
c) Discharge not exceeding 45 μC
N/A
d) Energy of discharge not exceeding 350 mJ
N/A
-N/A
Supplied by SELV circuit
N/A
9.1.1.2
Test with test finger and test probe
No hazardous live parts are
accessible
N/A
9.1.2
No hazardous live shafts of knobs, handles or levers
No such devices
N/A
9.1.3
Ventilation holes and other holes tested by means of
4 mm x 100 mm test pin
N/A
9.1.4
Terminal devices tested with 1 mm x 20 mm test pin
(10 N); test probe D of IEC 61032
N/A
Terminal devices tested with 1 mm x 100 mm straight
wire (1 N); test probe D of IEC 61032
N/A
9.1.5
Pre-set controls tested with 2.5 mm x 100 mm test pin No pre-set control
(10 N); test probe C of IEC 61032
N/A
9.1.6
No shock hazard due to stored charge on withdrawal
of the mains plug; voltage (V) after 2 s ................... :
N/A
If C is not greater than 0,1 μF no test needed
N/A
9.1.7
Resistance to external forces
After the tests as below, the
EUT shown no damage and
hazardous live parts are not
accessible
P
a) Test probe 11 of IEC 61032 for 10 s (50 N)
P
b) Test hook of fig. 4 for 10 s (20 N)
P
c) 30 mm diameter test tool for 5 s (100 or 250 N) :
N/A
The cover of apparatus is
fixed by screws. No cover
can be removed by hand
9.2
No hazard after removing a cover by hand
10
Insulation requirements
10.1
Insulation resistance (MΩ) at least 2 MΩ min. after
surge test for basic and 4 MΩ min. for reinforced
insulation ................................................................. :
N/A
10.2
Humidity treatment 48 h or 120 h ........................... :
N/A
TRF No. IEC60065K
N/A
--
Korea Testing Certification
Page 12 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
Result - Remark
Verdict
10.3
Insulation resistance and dielectric strength between
mains terminals
N/A
Insulation Resistance and dielectric strength across
BASIC or SUPPLEMENTARY insulation (Class I)
N/A
Insulation resistance and dielectric strength across
REINFORCED insulation (Class II)
N/A
11
Fault conditions
--
11.1
No shock hazard under fault condition
P
11.2
Heating under fault condition
See below
Flames extinguish within 10 seconds
No such condition occurred
N/A
No hazard from softening solder
No softening solder and
becoming fluid
N/A
Soldered terminations not used as protective
mechanism
No such termination
N/A
11.2.1
Measurement of temperature rises
(see appended table)
P
11.2.2
Temperature rise of accessible parts
(see appended table)
P
11.2.3
Temperature rise of parts, other than windings and
printed boards, providing electrical insulation
(see appended table)
P
11.2.4
Temperature rise of parts acting as a support or
mechanical barrier
N/A
11.2.5
Temperature rise of windings
N/A
11.2.6
Temperature rise of printed boards shall not exceed
the limits of table 3 by max. 100 K for max. 5 min
11.2.7
(see appended table)
P
P
Printed circuit boards (PCB) classified as V-0
according to 60695-11-10 or Clause G.1 may exceed
the limit in table 3 in case a) and b):
N/A
a) Temperature rise of printed circuit boards
exceeding the limits of table 3 by not more than 100 K
for an area not greater than 2 cm²
N/A
b) Temperature rise of printed circuit boards
exceeding the limits of table 3 up to 300 K for an area
not greater than 2 cm² for a maximum of 5 min
N/A
Meets all the special conditions if conductors on
printed circuit boards are interrupted
N/A
Class I protective earthing maintained
N/A
Temperature rise of parts not subject to the limits of
11.2.1 to 11.2.6 shall not exceed the limits in table 3,
item e), “Fault condition”
TRF No. IEC60065K
(see appended table)
P
Korea Testing Certification
Page 13 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
Result - Remark
Verdict
12
Mechanical strength
12.1.1
Bump test where mass >7 kg
N/A
12.1.2
Vibration test
N/A
12.1.3
Impact hammer test
N/A
Steel ball test
N/A
12.1.4
Drop test for portable apparatus where mass < 7 kg
N/A
12.1.5
Thermoplastic enclosures stress relief test
N/A
12.2
Fixing of knobs, push buttons, keys and levers
N/A
12.3
Remote controls with hazardous live parts
N/A
12.4
Drawers (pull test 50 N, 10 s)
No drawer is provided
N/A
12.5
Antenna coaxial sockets providing isolation
The antenna coaxial socket
is not used for isolation
N/A
12.6
Telescoping or rod antennas construction
No such device
N/A
12.6.1
Telescoping or rod antennas securement
13
Clearances and creepage distances
13.1
Clearances in accordance with 13.3
--
N/A
-Supplied by SELV circuit
N/A
Creepage distances in accordance with 13.4
N/A
13.2
Determination of operating voltage
N/A
13.3
Clearances
N/A
13.3.1
General
N/A
13.3.2
Circuits conductively connected to the mains comply
with table 8 and, where applicable, table 9
N/A
13.3.3
Circuits not conductively connected to the mains
comply with table 10
N/A
13.3.4
Measurement of transient voltages
N/A
13.4
Creepage distances
N/A
Creepage distances greater than table 11 minimum
values
N/A
13.5
Printed boards
N/A
13.5.1
Clearances and creepage distances between
conductors on printed circuit boards, one of which may
be conductively connected to the mains, as in fig. 10
N/A
13.5.2
Type B coated printed circuit boards complying with
IEC 60664-3 (basic insulation only)
N/A
13.6
Conductive parts along uncemented joints clearances
and creepage distances comply with 13.3 and 13.4
N/A
TRF No. IEC60065K
Korea Testing Certification
Page 14 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
Result - Remark
Verdict
Conductive parts along reliably cemented joints
comply with 8.8
N/A
Temperature cycle test and dielectric strength test
N/A
500V test for transformers, magnetic coupler and
similar devices, if insulation is relied upon for safety
N/A
13.7
Enclosed, enveloped or hermetically sealed parts: not
conductively connected to the mains: clearances and
creepage distances as in table 12
N/A
13.8
Parts filled with insulating compound, meeting the
requirements of 8.8
N/A
14
Components
14.1
Resistors
N/A
a) Resistors between hazardous live parts and
accessible metal parts
N/A
b) Resistors other than between hazardous live parts
and accessible parts
N/A
Resistors separately approved ............................... :
N/A
Capacitors and RC units
N/A
14.2
--
Capacitors separately approved
N/A
nd
N/A
nd
14.2.1
Y capacitors tested to IEC 60384-14, 2 edition ... :
14.2.2
X capacitors tested to IEC 60384-14, 2 edition ... :
N/A
14.2.3
Capacitors operating at mains frequency but not
connected to the mains: tests for X2 ...................... :
N/A
14.2.5
Capacitors with volume exceeding 1750 mm³, where
short-circuit current exceeds 0,2 A: compliance with
IEC60384-1, 4.38 category B or better ................... :
N/A
Capacitors with volume exceeding 1750 mm³,
mounted closer to a potential ignition source than
table 5 permits: compliance with IEC 60 384-1, 4.38
category B or better ................................................. :
N/A
Shielded by a barrier acc. to 20.1.4/ table 21 or metal
.................................................................................. :
N/A
Inductors and windings
N/A
14.3
Comply with IEC 61558-1, IEC 61558-2
(as relevant) and clause 20.1.4
14.3.1
14.3.2
Tested with appliance
Transformers and inductors marked with
manufacturer's name and type ............................... :
N/A
N/A
Transformers and inductors separately approved . :
Tested with appliance
N/A
General
See sub-clause 14.3.3,
14.3.4.1 and 14.3.5.1
N/A
TRF No. IEC60065K
Korea Testing Certification
Page 15 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
Result - Remark
Verdict
Insulation material complies with clause 20.1.4
N/A
14.3.3
Constructional requirements
N/A
14.3.3.1
Clearances and creepage distances comply with
clause 13
N/A
14.3.3.2
Transformers meet the constructional requirements
N/A
14.3.4
Separation between windings
N/A
14.3.4.1
Class II transformers have adequate separation
between hazardous live parts and accessible parts
(double or reinforced insulation)
N/A
Coil formers and partition walls > 0,4 mm
N/A
14.3.4.2
Class I transformers, with basic insulation and
protective screening only if all 7 conditions of 14.3.4.2
are met
N/A
14.3.4.3
Separating transformers with at least basic insulation
N/A
14.3.5
Insulation between HAZAROUS LIVE parts and
ACCESSIBLE parts
N/A
14.3.5.1
Class II transformers have adequate insulation
between hazardous live parts and accessible parts
(double or reinforced insulation)
N/A
Coil formers and partition walls > 0,4 mm
N/A
Class I transformers have adequate insulation
between hazardous live parts and accessible
conductive parts or those conductive parts or
protective screens connected to a protective earth
terminal
N/A
Winding wires connected to protective earth have
adequate current-carrying capacity
N/A
High voltage components
N/A
14.3.5.2
14.4
High-voltage components and assemblies: U > 4 kV
(peak) separately approved
No such high-voltage
components
Component meets category V-1 of IEC 60707
N/A
N/A
14.4.1
High voltage transformers and multipliers tested as
part of the submission
14.4.2
High voltage assemblies and other parts tested as part
of the submission
N/A
14.5
Protective devices
N/A
Protective devices used within their ratings
No such components
Used fuse
External clearances and creepage distances meet
requirement of clause 13 for the voltage across the
device when opened
14.5.1.1
a) Thermal cut-outs separately approved
b) Thermal cut-outs tested as part of the submission
TRF No. IEC60065K
N/A
N/A
N/A
No thermal cut-out
N/A
N/A
Korea Testing Certification
Page 16 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
Result - Remark
Verdict
14.5.1.2
a) Thermal links separately approved
No thermal links
N/A
b) Thermal links tested as part of the submission
N/A
14.5.1.3
Thermal devices re-settable by soldering
N/A
14.5.2.1
Fuse-links in the mains circuit according to IEC 60127
N/A
14.5.2.2
Correct marking of fuse-links adjacent to holder .... :
N/A
14.5.2.3
Not possible to connect fuses in parallel ................ :
N/A
14.5.2.4
Not possible to touch hazardous live parts when
replacing fuse-links without the use of a tool .......... :
N/A
14.5.3
PTC thermistors comply with IEC 60730-1:2007
N/A
PTC-S devices (15 W) category V-1 or better
N/A
14.5.4
Circuit protectors have adequate breaking capacity
and their position is correctly marked
No such component within
the EUT
14.6
Switches
Approved, see appended
table
14.6.1 a)
Separate testing to IEC 61058-1 including:
N/A
P
N/A
- 10 000 operations
- Normal pollution suitability
- Make and break speed independent of speed of
actuation
V-0 compliance with annex G, G.1.1
14.6.1 b)
Tested in the apparatus:
N/A
Switch controlling > 0.2A with open contact voltage >
35 V (peak)/24 V dc complying with 14.6.3, 14.6.4 and
V-0 in annex G, G.1.1
N/A
Switch controlling > 0.2A with open contact voltage <
35 V (peak)/24 V dc complying with 14.6.3 and V-0 in
annex G, G.1.1
N/A
Switch controlling < 0.2A with open contact voltage >
35 V (peak)/24 V dc complying with 14.6.4 and V-0 in
annex G, G.1.1
N/A
14.6.2
Switch tested to 14.6.1 b) constructed to IEC 61058-1
subclause 13.1 and has making/breaking action
independent of speed of actuation
N/A
14.6.3
Switch tested to 14.6.1 b) compliant with IEC 61058-1
subclause 16.2.2 d) and m) not attaining excessive
temperatures in use
N/A
14.6.4
Switch tested to 14.6.1 b) has adequate dielectric
strength
N/A
14.6.5
Mains switch controlling mains socket outlets
additional tests to IEC 60058-1
N/A
Socket outlet current marking correct
N/A
TRF No. IEC60065K
Korea Testing Certification
Page 17 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
Result - Remark
14.7
Safety interlocks
No safety interlocks
Safety interlocks to 2.8 of IEC 60950
14.8
Voltage setting devices and the like
Verdict
N/A
N/A
No such devices
Voltage setting device not likely to be changed
accidentally
N/A
N/A
14.9
Motors
No motor
14.9.1
Endurance test on motors
N/A
Motor start test
N/A
Dielectric strength test
N/A
14.9.2
Not adversely affected by oil or grease etc.
N/A
14.9.3
Protection against moving parts
14.9.4
Motors with phase-shifting capacitors, three-phase
motors and series motors meet clause. B.8, B.9 and
B.10 of IEC 60950, Annex B
N/A
14.10
Batteries
N/A
14.10.1
Batteries mounted with no risk of accumulation of
flammable gases
N/A
14.10.2
No possibility of recharging non-rechargeable batteries No battery charging circuit
within the remote controller
N/A
14.10.3
Recharging currents and times within manufacturers
limits
N/A
No moving parts
No rechargeable battery is
provided
N/A
N/A
Lithium batteries discharge and reverse currents within No lithium battery is
the manufacturers limits
provided
N/A
14.10.4
Battery mould stress relief
No such battery
N/A
14.10.5
Battery drop test
No such battery
N/A
14.11
Optocouplers
N/A
a) Comply with 13.6 (jointed insulation) and N.2.1
N/A
b) Comply with IEC 60747-5-5:2007
N/A
Alternative to a) and b) optocoupler comply with 13.8
14.12
Surge suppression varistors
N/A
Comply with IEC 61051-2
N/A
Not connected between mains and accessible parts
except for earthed parts of permanently connected
apparatus
N/A
Complies with the current pulse, fire hazard and
thermal stress requirements of 14.12
N/A
TRF No. IEC60065K
Korea Testing Certification
Page 18 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
15
Terminals
15.1.1
Mains plug, appliance inlet, interconnection couplers
and mains socket-outlet meet the appropriate
standard
15.1.2
Result - Remark
Verdict
-N/A
Overloading of plugs or appliance inlets prevented if
the apparatus has mains socket outlets
No mains socket outlet
N/A
Overloading of internal wiring prevented if the
apparatus has mains socket outlets
No mains socket outlet
N/A
Connectors for antenna, earth, audio, video or data:
No risk of insertion in mains socket-outlets
P
No such outlet
N/A
No risk of insertion into audio or video: outlets marked
with the symbol of 5.2
N/A
15.1.3
Output terminals of a.c. adaptors or similar devices not No such device
compatible with household mains socket-outlets
N/A
15.2
Provision for protective earthing
N/A
Accessible conductive parts of Class I equipment
reliably connected to earth terminal, within equipment
N/A
Protective earth conductors correctly coloured
N/A
Equipment with non-detachable mains cord provided
with separate protective earth terminal near mains
input
N/A
Protective earth terminal resistant to corrosion
N/A
Earth resistance test: < 0,1 Ω at 25 A .................... :
N/A
15.3
Terminals for external flexible cords and for
permanent connection to the mains supply
N/A
15.3.1
Adequate terminals for connection of permanent
wiring
15.3.2
Reliable connection of non-detachable cords:
N/A
Not soldered to conductors of a printed circuit board
N/A
Adequate clearances and creepage distances
between connections should a wire break away
N/A
Wire secured by additional means to the conductor
N/A
15.3.3
Screws and nuts clamping conductors have adequate
threads: ISO 261, ISO 262 or similar
N/A
15.3.4
Soldered conductors wrapped around terminal prior to
soldering or held in place by additional means
N/A
Clamping of conductor and insulation if not soldered or
held by screws
N/A
Terminals allow connection of appropriate crosssectional area of conductors, for the rated current of
the equipment
N/A
15.3.5
TRF No. IEC60065K
The EUT is not a
permanently connected
apparatus
N/A
Korea Testing Certification
Page 19 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
15.3.6
Terminals to 15.3.3 have sizes required by table 16
N/A
15.3.7
Terminals clamp conductors between metal and have
adequate pressure
N/A
Terminals designed to avoid conductor slipping out
when tightened or loosened
N/A
Terminals adequately fixed to avoid loosening when
the clamping is tightened or loosened and stress on
internal wiring is avoided
N/A
15.3.8
Terminals carrying a current more than 0,2 A: contact
pressure not transmitted by insulating material except
ceramic
N/A
15.3.9
Termination of non-detachable cords: wires terminated
near to each other
N/A
Terminals located and shielded: test with 8 mm strand
N/A
15.4
Devices forming a part of the mains plug
N/A
15.4.1
No undue strain on mains socket-outlets
N/A
15.4.2
Device complies with standard for dimensions of
mains plugs
N/A
15.4.3
Device has adequate mechanical strength (tests a,b,c)
N/A
16
External flexible cords
16.1
Mains cords sheathed type, complying with IEC 60227 The EUT is supplied by an
for PVC or IEC 60245 for synthetic rubber cords ... :
adapter
N/A
Non-detachable cords for Class I have green/yellow
core for protective earth
N/A
16.2
Mains cords conductors have adequate crosssectional area for rated current consumption of the
equipment
N/A
16.3
a) Flexible cords not complying with 16.1, used for
interconnections between separate units of equipment
used in combination and carrying hazardous live
voltages, have adequate dielectric strength
N/A
b) Flexible cords not complying with 16.1, withstand
bending and mechanical stress (3.2 of IEC 60227-2)
N/A
16.4
Flexible cords used for connection between equipment
have adequate cross-sectional areas to avoid
temperature rise under normal and fault conditions
N/A
16.5
Adequate strain relief on external flexible cords
N/A
Not possible to push cord back into equipment
N/A
Strain relief device unlikely to damage flexible cord
N/A
For mains cords of Class I equipment, hazardous live
conductors become taut before earth conductor
N/A
TRF No. IEC60065K
Result - Remark
Verdict
--
Korea Testing Certification
Page 20 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
Result - Remark
Verdict
16.6
Apertures for external flexible cord: no risk of damage
to the cord during assembly or movement in use
N/A
16.7
Transportable musical instruments and amplifiers
fitted with detachable cord set with appliance inlet to
IEC 60320-1
N/A
Transportable musical instruments and amplifiers
fitted with detachable cord sets or with means of
stowage to protect the cord
N/A
17
Electrical connections and mechanical fixings
--
17.1
Torque test to table 20:
P
- screws into metal: 5 times
P
- screws into non-metallic material: 10 times
N/A
17.2
Correct introduction into female threads in non-metallic
material
N/A
17.3
Cover fixing screws: captive
N/A
Non-captive fixing screws: no hazard when replaced
by a screw whose length is 10 times its diameter
N/A
17.4
No loosening of conductive parts carrying a current
> 0,2 A
No such parts
N/A
17.5
Contact pressure not transmitted through plastic other No such parts
than ceramic for connections carrying a current
> 0,2 A
N/A
17.6
Stranded conductors of flexible supply cords carrying a
current > 0,2 A with screw terminals not consolidated
by solder
N/A
17.7
Cover fixing devices other than screws have adequate No such device
strength and their positioning is unambiguous
N/A
17.8
Fixing devices for detachable legs or stands provided
N/A
17.9
Internal pluggable connections, affecting safety,
unlikely to become disconnected
N/A
18
Mechanical strength of picture tubes and protection against the effects of
implosion
18.1
Picture tube separately approved to IEC 61965:
No picture tube
-N/A
Picture tube separately approved to 18.2 ................
N/A
18.2
Non-intrinsically protected tubes tested to 18.2
N/A
19
Stability and mechanical hazards
Mass of the equipment exceeding 7 kg .................. :
TRF No. IEC60065K
-N/A
Korea Testing Certification
Page 21 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
Result - Remark
Apparatus intended to be fastened in place – suitable
instructions
Verdict
N/A
o
19.1
Test on a plane, inclined at 10 to the horizontal
N/A
19.2
100 N force applied vertically downwards
N/A
19.3
100 N force, or 13% of weight, applied horizontally to
point of least stability.
N/A
19.4
Edges or corners not hazardous
19.5
Glass surfaces (exc.laminated) with an area
exceeding 0,1 m² or maximum dimension > 450 mm,
pass the test of 19.5.1
19.6
Wall or ceiling mountings adequate
20
Resistance to fire
--
20.1
Electrical components and mechanical parts
P
The outer surface of the
EUT is smoothed, no sharp
edges and corners
P
N/A
Not intended for wall or
ceiling mountings
a) Exemption for components contained in an
enclosure of material V-0 to IEC 60695-11-10 with
openings not exceeding 1 mm in width
N/A
N/A
b) Exemption for small components as defined in 20.1 Components are mounted
on PCB of V-0
P
20.1.1
Electrical components meet the requirements of
Clause 14 or 20.1.4
The plastic enclosures
complied with sub-clause
20.1.4
P
20.1.2
Insulation of internal wiring working at voltages > 4 Kv
or leaving an internal fire enclosure, or located within
the areas mentioned in Table 21, not contributing to
the spread of fire
No voltage more than 4 kV
N/A
20.1.3
Material of printed circuit boards on which the available The PCB has the
power exceeds 15 W at a voltage between 50 V and
flammability rating of V-0
400 V (peak) a.c. or d.c. meets V-1 or better to IEC
60695-11-10, unless used in a fire enclosure
20.1.4
P
Material of printed circuit boards on which the available No >400V (peak) a.c. or d.c.
power exceeds 15 W at a voltage >400 V (peak) a.c.
or d.c. meets V-0 to IEC 60695-11-10.
N/A
Components and parts not covered by 20.1.1, 20.1.2
and 20.1.3 (other than fire enclosures) mounted
nearer to a potential ignition source than the distances
in Table 21 comply with the relevant flammability
category in Table 21
N/A
Components and parts as above but shielded from a
potential ignition source, with the barrier area in
accordance with Table 21 and fig. 13
TRF No. IEC60065K
No such barrier
N/A
Korea Testing Certification
Page 22 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
Result - Remark
Apparatus with voltages >4kV under normal operating
conditions and distances to the enclosure exceed
those specified Table 21, flammability classification
HB40 or better is required for the enclosure.
No voltage more than 4 kV
Verdict
N/A
20.2
Fire enclosure
N/A
20.2.1
Potential ignition sources with open circuit voltage
> 4 kV (peak) a.c. or d.c. contained in a fire enclosure
to V-1
N/A
20.2.2
Internal fire enclosures with openings not exceeding
1 mm in width and with openings for wires completely
filled
N/A
20.2.3
Requirements of 20.2.1 and 20.2.2 met by an internal
fire enclosure
N/A
TRF No. IEC60065K
Korea Testing Certification
Page 23 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
A
Annex A, Additional requirements for apparatus with protection against
splashing water
A.5
Marking and instructions
N/A
A.5.1
j) Marked with IPX4 (IEC 60529), 5.4.1 a) does not
apply
N/A
A.10
Insulation requirements
N/A
A.10.2
Splash and humidity treatment
N/A
A.10.2.1
Enclosure provides protection against splashing water
N/A
A.10.2.2
Humidity treatment carried out for 7 days
N/A
B
Annex B, Apparatus to be connected to the TELECOMMUNICATION
NETWORKS
Complies with IEC 62151 clause 1
Result - Remark
No connected to the
telecommunication
networks
Verdict
--
-N/A
Complies with IEC 62151 clause 2
N/A
Complies with IEC 62151 clause 3 but with 3.5.4
modified to 2.4.10 of this standard
N/A
Complies with IEC 62151 clause 4 but with 4.1.2, 4.1.3
and 4.2.1.2 modified in accordance with annex B of
this standard
N/A
Complies with IEC 62151 cause 5 but with 5.3.1
modified in accordance with annex B of this standard
N/A
Complies with IEC 62151 clause 6
N/A
Complies with IEC 62151 clause 7
N/A
Complies with IEC 62151 annex A, B and C
N/A
L
ANNEX L, Additional requirements for electronic flash apparatus for
photographic purposes
L. 5
Marking and instructions
N/A
L. 5.4
Instructions for battery chargers and Supply apparatus
indicating type or model number of flash apparatus
with which it is to be used
N/A
Instructions for flash apparatus indicating type or
model number of battery chargers or Supply
apparatus with which it is to be used
N/A
L. 7
Heating under normal operating conditions
N/A
L7.1.5 &
Lithium batteries meet permissible temp rise in Table
3, unless comply with 6.2.2.1 or 6.2.2.2 of IEC 600864
N/A
Electric shock hazard under normal operating
conditions
N/A
L11.2.7
L. 9
TRF No. IEC60065K
Korea Testing Certification
Page 24 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
L. 9.1.1
Terminals to connection to synchroniser not
HAZARDOUS LIVE
N/A
L.10
Insulation requirements
N/A
L. 10.3.2
High frequency puls ignition
N/A
L. 12
Mechanical strength
N/A
L. 12.1.3
Windows for flash tubes are excluded from steel ball
impact test
N/A
L. 14
Components
N/A
L14.6.6
Mains switch characteristics appropriate to its function
under normal conditions
N/A
L. 20
Resistance to fire
N/A
L. 20.1 c)
Trigger coil for discharge purpose is not considered to
be a POTENTIAL IGNITION SOURCE
N/A
TRF No. IEC60065K
Result - Remark
Verdict
Korea Testing Certification
Page 25 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
Result - Remark
7.1
TABLE: temperature rise measurements
Verdict
P
Power consumption in the OFF/Stand-by
--
—
Position of the functional switch (W) ...................... : --
—
Operating conditions
Video Recorder powered by external adapter.
Un (V)
In (A)
Pn (W)
DC 12V
0.52
--
Pout (W)
USB terminal load
500mA.
Loudspeaker impedance (Ω) .................................. :
--
—
Several loudspeaker systems
--
--
Marking of loudspeaker terminals
--
--
Monitored point:
dT (K)
Limit dT (K)
Power cord
1.0
45
AC adapter surface
7.2
60
AC adapter output wire
2.6
45
DC inlet
9.2
50
Switch
7.1
50
Internal DC wire for switch
11.4
45
J50 body
12.4
60
C538 body
17.6
70
PCB near heatsink
26.0
95
USB terminal
11.8
50
Metal enclosure
1.8
40
Plastic enclosure
0.4
50
Note: *See table 14 for temperature limit value, manufacturer’s recommended ambient (Tmra) of 35°C.
Winding temperature rise measurements
N/A
o
—
o
—
Ambient temperature t1 ( C) ................................... : 35
Ambient temperature t2 ( C) ................................... : 35
Temperature rise dT of winding:
--
TRF No. IEC60065K
R1 (Ω)
R2 (Ω)
dT (K)
Limit dT (K)
Insulation
class
--
--
--
--
--
Korea Testing Certification
Page 26 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
Result - Remark
7.2
TABLE: softening temperature of thermoplastics
Temperature T of part
N/A
T - normal cono
ditions ( C)
T - fault condio
tions ( C)
T softening
o
( C)
--
--
--
-10.3
Verdict
TABLE: insulation resistance measurements
N/A
R (MΩ)
Required R (MΩ)
--
--
--
--
--
--
Insulation resistance R between:
Note:
1) BI: Basic insulation; SI: Supplementary insulation; DI: Double insulation; RI: Reinforced insulation.
2) The test performed between L/N of power supply unit and the terminal of tuner.
3) The cores of transformers are considered as free body.
10.3
TABLE: electric strength measurements
N/A
Test voltage applied between:
Test voltage (V)
Breakdown
--
--
-Note:
1) BI: Basic insulation; SI: Supplementary insulation; DI: Double insulation; RI: Reinforced insulation.
2) The test performed between L/N of power supply unit and the terminal of tuner.
3) The cores of transformers are considered as free body.
11.2
TABLE: summary of fault condition tests
P
Voltage (V) 0,9 or 1,1 times rated voltage .............. : DC 12V
—
Frequency (Hz) ........................................................ : -o
o
Ambient temperature ( C) ....................................... : 35 C
No.
1
Component
USB terminal
Fault
short circuit
—
dT (K) / Component Other results
(include description and test duration)
--
Mains input current is 0.53A . Unit works
normally.
No damage. No hazards.
2
U46 pin2-6
short circuit
--
After short circuit, unit operated normally.
No damage, no hazards.
3
DN1
short circuit
--
After short circuit, unit operated normally.
No damage, no hazards.
4
C538
short circuit
--
After short circuit, unit operated normally.
No damage, no hazards.
5
Ventilation
hole
TRF No. IEC60065K
block
--
No damage, no hazards.
Korea Testing Certification
Page 27 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
Result - Remark
Monitored point:
dT (K)
Power cord
1.8
AC adapter surface
7.6
AC adapter output wire
0.6
DC inlet
8.8
Switch
6.7
Internal DC wire for switch
11.2
J50 body
12.3
C538 body
17.5
PCB near heatsink
25.9
USB terminal
11.9
Metal enclosure
8.1
Plastic enclosure
1.5
6
USB terminal
Verdict
overload
--
USB overload: 1.2→2.0→2.6→3.1(A); Input
current: 1.098→1.515→1.836→0.547(A);
No damage, no hazards.
Monitored point:
dT (K)
AC adapter surface
14.3
DC inlet
18.0
Switch
11.2
PCB near heatsink
29.8
USB terminal
18.8
Metal enclosure
10.1
Plastic enclosure
Winding temperature rise measurements
0.5
o
—
o
—
Ambient temperature t1 ( C) ................................... : 35
Ambient temperature t2 ( C) ................................... : 35
13
TABLES: clearances and creepage distances
Rated supply voltage:
100-240
Pollution degree:
N/A
2
Material Group:
2 N force on internal parts applied:
N/A
30 N force on outside of conductive enclosure applied:
N/A
Location
Operating Voltage
V rms
V peak
Clearance (mm)
Min
Actual
IIIa/b
Creepage (mm)
Min
Actual
--
--
Circuits conductively connected to the mains (use Tables 8, 9 and 11): see note below.
-Notes:
TRF No. IEC60065K
--
--
--
--
Korea Testing Certification
Page 28 of 28
Report No.: W14-65-007
IEC 60065
Clause
Requirement – Test
14
TABLE: list of critical components and materials
Component
Manufacturer/
Result - Remark
Type/model
P
Value / rating
Standard
trademark
Approval/
Reference
3G0.75mm
2
UL 758
Power cord
Ningbo Qiaopu
Electric Co., Ltd.
H05VV-F
SWITCHING
ADAPTER
SHENZHEN FUJIA
APPLIANCE CO
LTD
FJ-SW1205000 Input: 100IEC 60065
240V~, 50/60Hz,
1.5A MAX.
Output:
,
12V
5000mA
Switch
SHENZHEN
R13-2
GOODPAL
ELECTRONICS CO
LTD
Internal wire
ZHUANG SHAN
conect to switch CHUAN
ELECTRICAL
PRODUCTS
(KUNSHAN) CO
LTD
Verdict
6A, 250VAC;
10A. 125VAC
2468 or 1185 or VW-1, 80°C,
2464
300V, 18AWG
UL E232289
KTC
HU1053911008
IEC/EN 61058-1 VDE
UL 61058-1
40008573
UL E241010
UL 758
UL E333601
VW-1, 80ºC,
2468 or 1185 or
300V, min.
2464
22AWG
UL 758
UL
Alternative
Various
Internal wire
SHENZHEN
JINRUIHUA WIRE
& CABLE CO LTD
1007
VW-1, 80°C,
300V, 18AWG
UL 758
UL
Internal wire for
signal
3C TAEYANG CO
LTD
60624
VW-1, 60V,
80℃
UL 758
UL
Conector
SHENZHEN
SHINNING
ELECTRONIC CO
LTD
ECBT2
250V,7A
UL 1977
UL E241307
PCB
VARIOUS
VARIOUS
V-0, 130°C,
UL 796
UL
Min. thickness:
1.6mm
UL 94
600V, 125°C,
VW-1, min.
thickness:
0.4mm
UL 510
Heat shrinkable
tube
SHENZHEN WOER RSFR-H
HEATSHRINKABLE
MATERIAL CO LTD
1
) an asterisk indicates a mark which assures the agreed level of surveillance
Remarks
TRF No. IEC60065K
UL
Page 1 of 16
Korea Testing Certification
Report No.: W14-65-007
Attachment 1 - European group differences and national differences
(EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011)
IEC60065K - ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
ATTACHMENT TO TEST REPORT IEC 60065
EUROPEAN GROUP DIFFERENCES AND NATIONAL DIFFERENCES
Audio, video and similar electronic apparatus – Safety requirements
Differences according to ............... :
EN 60065:2002 + A1:2006 + A11:2008 + A2:2010 + A12:2011
Attachment Form No. ..................... :
EU_GD_IEC60065K_II
Attachment Originator ................... :
Intertek Semko AB
Master Attachment ......................... :
Date (2011-08)
Copyright © 2010 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
IEC 60065, GROUP DIFFERENCES (CENELEC common modifications (EN))
Clause
Requirement + Test
Contents
Add the following annexes:
Annex ZA (normative) Other international publications quoted in this standard with
the references of the relevant European publications (See the CB Bulletin)
Annex ZB (nominative) Special national conditions
Annex ZC (informative) A-deviations
Definition
Add after the definition 2.2.12 the following new
definition:
2.2.Z1
(A11:2008) PORTABLE SOUND SYSTEM
small battery powered audio equipment:
•
whose prime purpose is to listen to recorded or
broadcasted sound; and
•
that uses headphones or earphones that can
be worn in or on or around the ears; and
Result - Remark
Verdict
N/A
N/A
• that allows the user to walk around
NOTE Examples are mini-disc or CD players, MP3
audio players or similar equipment.
2.2
In EN 60065:2002/A11:2008
(A12:2011) Delete the definition 2.2.Z1
N/A
Page 2 of 16
Korea Testing Certification
Report No.: W14-65-007
Attachment 1 - European group differences and national differences
(EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011)
IEC60065K - ATTACHMENT
Clause
Requirement + Test
3.1
Add the following indent at the end of the list
Result - Remark
Verdict
N/A
-
Exposure to excessive sound pressures from
headphones or earphones
NOTE A new method of measurement is described
in EN 50332-1, Sound system equipment:
Headphones and earphones associated with
portable audio equipment
– Maximum sound pressure level measurement
methodology and limit considerations – Part 1:
General method for ”one package equipment”, and
in EN 50332-2, Sound system equipment:
Headphones and earphones associated with
portable audio equipment – Maximum sound
pressure level measurement methodology and limit
considerations – Part 2: Guidelines to associate
sets with headphones coming from different
manufacturers.
In EN 60065:2002
3.1
(A12:2011) Delete the addition of indent regarding sound
pressure excessive
N/A
3.Z1
After 3.2 add a new clause 3.Z1:
N/A
(A2:2010)
To protect against excessive current, short-circuits
and earth faults in MAINS, protective devices shall
be included either as integral parts of the
equipment or as parts of the building installation,
subject to the following, a), b) and c):
a) except as detailed in b) and c), protective
devices necessary to comply with the requirements
of 11 shall be included as parts of the equipment;
b) for components in series or parallel with the
mains input to the equipment such as the supply
cord, appliance coupler, r.f.i. filter and switch, shortcircuit and earth fault protection may be provided
by protective devices in the building installation;
c) it is permitted for equipment supplied via an
industrial mains plug or for PERMANENTLY
CONNECTED APPARATUS, to rely on dedicated
over current and short-circuit protection in the
building installation, provided that the means of
protection, e.g. fuses or circuit breakers, is fully
specified in the installation instructions.
If reliance is placed on protection in the building
installation, the installation instructions shall so
state, except that for not via an industrial mains
plug or for PERMANENTLY CONNECTED
APPARATUS the building installation shall be
regarded
4.1.1
Replace the text of the note by: NOTE For
ROUTINE TEST reference is made to EN 50514.
--
Korea Testing Certification
Page 3 of 16
Report No.: W14-65-007
Attachment 1 - European group differences and national differences
(EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011)
IEC60065K - ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
Modify indent za) as follows:
5.4.1
za)
za) For a PORTABLE SOUND SYSTEM, a warning
(A11:2008) that excessive sound pressure from earphones and
headphones can cause hearing loss.
N/A
5.4.1
In EN 60065:2002/A1:2006 and EN
(A12:2011) 60065;2002/A11:2008
Delete the modification in indent za)
Add the following clause and annex to the excisting
standard and amendments
N/A
Zx Protection against excessive sound pressure from personal music players
N/A
Korea Testing Certification
Page 4 of 16
Report No.: W14-65-007
Attachment 1 - European group differences and national differences
(EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011)
IEC60065K - ATTACHMENT
Clause
Requirement + Test
Zx.1 General
This sub-clause specifies requirements for
protection against excessive sound pressure from
personal music players that are closely coupled to
the ear. It also specifies requirements for
earphones and headphones intended for use with
personal music players.
A personal music player is a portable equipment for
personal use, that:
is designed to allow the user to listen to recorded
or broadcast sound or video; and
primarily uses headphones or earphones that can
be worn in or on or around the ears; and
allows the user to walk around while in use.
NOTE 1 Examples are hand-held or body-worn portable CD
players, MP3 audio players, mobile phones with MP3 type
features, PDA’s or similar equipment.
A personal music player and earphones or
headphones intended to be used with personal
music players shall comply with the requirements of
this sub-clause.
The requirements in this sub-clause are valid for
music or video mode only.
The requirements do not apply:
while the personal music player is connected to an
external amplifier; or
while the headphones or earphones are not used.
NOTE 2 An external amplifier is an amplifier which is not part of
the personal music player or the listening device, but which is
intended to play the music as a standalone music player.
The requirements do not apply to:
hearing aid equipment and professional
equipment;
NOTE 3 Professional equipment is equipment sold through
special sales channels. All products sold through normal
electronics stores are considered not to be professional
equipment.
analogue personal music players (personal music
players without any kind of digital
processing of the sound signal) that are brought
to the market before the end of 2015.
NOTE 4 This exemption has been allowed because this
technology is falling out of use and it is expected that within a
few years it will no longer exist. This exemption will not be
extended to other technologies.
For equipment which is clearly designed or
intended for use by young children, the limits of
EN 71-1 apply.
Result - Remark
Verdict
N/A
Korea Testing Certification
Page 5 of 16
Report No.: W14-65-007
Attachment 1 - European group differences and national differences
(EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011)
IEC60065K - ATTACHMENT
Clause
Requirement + Test
Cont.
Zx.2 Equipment requirements
No safety provision is required for equipment that
complies with the following:
equipment provided as a package (personal music
player with its listening device), where
the acoustic output LAeq,T is ≤ 85 dBA measured
while playing the fixed “programme
simulation noise” as described in EN 50332-1;
and
a personal music player provided with an
analogue electrical output socket for a listening
device, where the electrical output is ≤ 27 mV
measured as described in EN 50332-2, while
playing the fixed “programme simulation noise” as
described in EN 50332-1.
NOTE 1 Wherever the term acoustic output is used in this
clause, the 30 s A-weighted equivalent sound pressure level
LAeq,T is
meant. See also Zx.5 and Annex Zx.
All other equipment shall:
a) protect the user from unintentional acoustic
outputs exceeding those mentioned above; and
b) have a standard acoustic output level not
exceeding those mentioned above, and
automatically return to an output level not
exceeding those mentioned above when the
power is switched off; and
c) provide a means to actively inform the user of the
ncreased sound pressure when the equipment is
operated with an acoustic output exceeding
those mentioned above. Any means used shall
be acknowledged by the user before activating a
mode of operation which allows for an acoustic
output exceeding those mentioned above. The
acknowledgement does not need to be repeated
more than once every 20 h of cumulative
listening time; and
NOTE 2 Examples of means include visual or audible signals.
Action from the user is always required.
NOTE 3 The 20 h listening time is the accumulative listening
time, independent how often and how long the personal music
player has been switched off.
d) have a warning as specified in Zx.3; and
e) not exceed the following:
1) equipment provided as a package (player with
Its listening device), the acoustic output shall be
≤ 100 dBA measured while playing the fixed
“programme simulation noise” described in EN
50332-1; and
2) a personal music player provided with an
analogue electrical output socket for a listening
device, the electrical output shall be ≤ 150 mV
measured as described in EN 50332-2, while
playing the fixed “programme simulation noise”
described in EN 50332-1.
Result - Remark
Verdict
N/A
Korea Testing Certification
Page 6 of 16
Report No.: W14-65-007
Attachment 1 - European group differences and national differences
(EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011)
IEC60065K - ATTACHMENT
Clause
Cont.
Requirement + Test
For music where the average sound pressure (long
term LAeq,T) measured over the duration of the
song is lower than the average produced by the
programme simulation noise, the warning does not
need to be given as long as the average sound
pressure of the song is below the basic limit of 85
dBA. In this case T becomes the duration of the
song.
Result - Remark
Verdict
N/A
NOTE 4 Classical music typically has an average sound
pressure (long term LAeq,T) which is much lower than the average
programme simulation noise. Therefore, if the player is capable
to analyse the song and compare it with the programme
simulation noise, the warning does not need to be given as long
as the average sound pressure of the song is below the basic
limit of 85 dBA.
For example, if the player is set with the programme simulation
noise to 85 dBA, but the average music level of the song is only
65 dBA, there is no need to give a warning or ask an
acknowledgement as long as the average sound level of the
song is not above the basic limit of 85 dBA.
Zx.3 Warning
The warning shall be placed on the equipment, or
on the packaging, or in the instruction manual and
shall consist of the following:
the symbol of Figure 1 with a minimum height of 5
mm; and
the following wording, or similar:
“To prevent possible hearing damage, do not listen
at high volume levels for long periods.”
Figure 1 – Warning label (IEC 60417-6044)
Alternatively, the entire warning may be given
through the equipment display during use,
when the user is asked to acknowledge activation
of the higher level.
N/A
Korea Testing Certification
Page 7 of 16
Report No.: W14-65-007
Attachment 1 - European group differences and national differences
(EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011)
IEC60065K - ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
Cont.
Zx.4 Requirements for listening devices (headphones and earphones)
N/A
Zx.4.1 Wired listening devices with analogue
input
With 94 dBA sound pressure output LAeq,T, the input
voltage of the fixed “programme simulation noise”
described in EN 50332-2 shall be ≥ 75 mV.
N/A
This requirement is applicable in any mode where
the headphones can operate (active or
passive), including any available setting (for
example built-in volume level control).
NOTE The values of 94 dBA – 75 mV correspond with 85dBA –
27 mV and 100 dBA – 150 mV.
Zx.4.2 Wired listening devices with digital input
N/A
With any playing device playing the fixed
“programme simulation noise” described in
EN 50332-1 (and respecting the digital interface
standards, where a digital interface standard
exists that specifies the equivalent acoustic level),
the acoustic output LAeq,T of the listening device
shall be ≤ 100 dBA.
This requirement is applicable in any mode where
the headphones can operate, including any
available setting (for example built-in volume level
control, additional sound feature like
equalization, etc.).
NOTE An example of a wired listening device with digital input is
a USB headphone.
.
Zx.4.3 Wireless listening devices
In wireless mode:
with any playing and transmitting device playing
the fixed programme simulation noise described
in EN 50332-1; and
respecting the wireless transmission standards,
where an air interface standard exists that
specifies the equivalent acoustic level; and
with volume and sound settings in the listening
device (for example built-in volume level control,
additional sound feature like equalization, etc.)
set to the combination of positions that maximize
the measured acoustic output for the abovementioned programme simulation noise, the
acoustic output LAeq,T of the listening device shall
be ≤ 100 dBA.
NOTE An example of a wireless listening device is a Bluetooth
headphone.
N/A
Korea Testing Certification
Page 8 of 16
Report No.: W14-65-007
Attachment 1 - European group differences and national differences
(EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011)
IEC60065K - ATTACHMENT
Clause
Requirement + Test
Zx.5 Measurement methods
Measurements shall be made in accordance with
EN 50332-1 or EN 50332-2 as applicable.
Unless stated otherwise, the time interval T shall be
30 s.
NOTE Test method for wireless equipment provided without
listening device should be defined.
Result - Remark
Verdict
N/A
Korea Testing Certification
Page 9 of 16
Report No.: W14-65-007
Attachment 1 - European group differences and national differences
(EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011)
IEC60065K - ATTACHMENT
Clause
Requirement + Test
Replace the entire subclause in EN 60065:2002
and EN 60065:2002/A1:2006 by:
(A11:2008) Ionizing radiation
Apparatus including a potential source of ionizing
radiation shall be so constructed that personal
protection against ionizing radiation is provided
under normal operating conditions and under fault
conditions.
Compliance is checked by measurement under the
following conditions:
In addition to the normal operating conditions, all
controls adjustable from the outside BY HAND, by
any object such as a tool or a coin, and those
internal adjustments or pre-sets which are not
locked in a reliable manner, are adjusted so as to
give maximum radiation whilst maintaining an
intelligible picture for 1 h, at the end of which the
measurement is made.
NOTE 1 Soldered joints and paint lockings are
examples of adequate locking.
The dose-rate is determined by means of a
radiation monitor with an effective area of 10 cm²,
at any point 10 cm from the outer surface of the
apparatus.
Moreover, the measurement shall be made under
fault conditions causing an increase of the highvoltage, provided an intelligible picture is
maintained for 1 h, at the end of which the
measurement is made.
The dose-rate shall not exceed 1μSv/h (0,1 mR/h)
taking account of the background level.
NOTE 2 These values appear in Directive
96/29/Euratom of 13th May 1996.
A picture is considered to be intelligible if the
following conditions are met:
- a scanning amplitude of at least 70 % of the
usable screen width;
- a minimum luminance of 50 cd/m² with locked
blank raster provided by a test generator;
- a horizontal resolution corresponding to at least
1,5 MHz in the centre, with a similar vertical
degradation;
- not more than one flashover per 5 min.
6.1
Result - Remark
Verdict
N/A
Korea Testing Certification
Page 10 of 16
Report No.: W14-65-007
Attachment 1 - European group differences and national differences
(EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011)
IEC60065K - ATTACHMENT
Clause
Requirement + Test
Result - Remark
Add the following new clause after Clause 20:
Z1
(A11:2008) Z1 Resistance to candle flame ignition
A television set shall be so designed that the
likelihood of ignition and the spread of fire caused
by a candle flame is reduced.
NOTE 1 An apparatus with a viewing screen is not
regarded to be a television set if it is declared not to
be so by the manufacturer.
This requirement does not apply to the display
screen of rear projection TV’s.
NOTE 2 This exemption has been allowed because
this technology is falling out of use and it is
expected that within a few years it will no longer
exist. This exemption will not be extended to other
technologies.
NOTE 3 The frame around the screen is not
exempted from the requirements.
Wood and WOOD-BASED MATERIAL with a
thickness of at least 6 mm is considered to fulfil the
V-1 requirement when applying CLC/TS 62441.
Compliance is checked according to CLC/TS
62441.
NOTE 4 The term vertical, as used in the first dash
of clause 5.2 of CLC/TS 62441, does not mean a
perfectly vertical position. It should be interpreted
as any surface that can be touched by the flame of
a candle of 150 mm height and 20mm diameter
while the candle is still touching the supporting
surface. A typical candle used in the home is
assumed to be 20 mm diameter.
NOTE 5 It is expected that CLC/TS 62441 will in
the future be replaced by a standard, at which time
that standard will become applicable, subject to a
vote by National Committees at the time.
General
13.3.1
14
15.1.1
15.2
16.1
16.2
20
Annex B
Annex G
Annex J.2
Annex N
Delete note 4.
Delete note 4 and note 5.
Delete notes 1 and 2.
Delete note 2.
Delete note 1.
Delete the note.
Delete note 2.
Replace note 1 by: In the CENELEC countries listed in IEC 62151,
special national conditions apply.
Delete the note.
Delete the notes of Table J.1.
Add after the introduction: For ROUTINE TEST reference is made to
EN 50333. (Replaced by EN 50514)
Verdict
N/A
P
Page 11 of 16
Korea Testing Certification
Report No.: W14-65-007
Attachment 1 - European group differences and national differences
(EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011)
IEC60065K - ATTACHMENT
Clause
Requirement + Test
Result - Remark
General
(A2:2010)
In IEC 60065:2001/A2
Delete all the “country” notes according to the following list:
5.3
Note
5.4.1 Note
20
Note
For special national conditions, see Annex ZB.
Verdict
P
Bibliography Additional EN standards.
P
ZA
Normative references to international publications
with their corresponding European publications
P
ZB
ANNEX ZB TO EN 60065, SPECIAL NATIONAL CONDITIONS (EN)
P
2.6.1
DK: The following is added:
N/A
Certain types of CLASS I apparatus, see 15.1.1,
may be provided with a plug not establishing
earthing continuity when inserted in Danish socketoutlets
Justification: Heavy Current Regulations, Section
107.
3.Z1
(A2:2010)
Denmark
Add to the end of the subclause
Due to many existing installations where the
socket-outlets can be protected with
fuses with higher rating than the rating of the
socket-outlets the protection for
pluggable equipment type A shall be an integral
part of the equipment.
Justification:
In Denmark an existing 13 A socket outlet can be
protected by a 20 A fuse.
N/A
Korea Testing Certification
Page 12 of 16
Report No.: W14-65-007
Attachment 1 - European group differences and national differences
(EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011)
IEC60065K - ATTACHMENT
Clause
Requirement + Test
5.3
(A2:2010)
Finland, Norway and Sweden
To the end of the subclause the following is added:
CLASS I apparatus which is intended for connection
to the building installation wiring
via a plug or an appliance coupler, or both and in
addition is intended for connection
to other apparatus or a network shall, if safety
relies on connection to protective earth
or if surge suppressors are connected between the
network TERMINALS and
ACCESSIBLE parts, have a marking stating that the
apparatus must be connected to an
earthed MAINS socket-outlet.
The marking text in the applicable countries shall
be as follows:
In Finland: "Laite on liitettävä suojakoskettimilla
varustettuun pistorasiaan"
In Norway: “Apparatet må tilkoples jordet
stikkontakt”
In Sweden: “Apparaten skall anslutas till jordat
uttag”
Finland, Norway and Sweden
5.4
(A11:2008) To the end of 5.4 the following is added:
CLASS I apparatus which is intended for
connection to the building installation wiring via a
plug or an appliance coupler, or both and in
addition is intended for connection to other
apparatus or a network shall, if safety relies on
connection to protective earth or if surge
suppressors are connected between the network
TERMINALS and ACCESSIBLE parts, have a
marking stating that the apparatus must be
connected to an MAINS socket-outlet with
protective earth.
The marking text in the applicable countries shall
be as follows:
In Finland: “Laite on liitettävä
suojamaadoituskoskettimilla varustettuun
pistorasiaan”
In Norway: “Apparatet må tilkoples jordet
stikkontakt”
In Sweden: "Apparaten skall anslutas till jordat
uttag"
Result - Remark
Verdict
N/A
N/A
Korea Testing Certification
Page 13 of 16
Report No.: W14-65-007
Attachment 1 - European group differences and national differences
(EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011)
IEC60065K - ATTACHMENT
Clause
Requirement + Test
Norway and Sweden
5.4.1
(A11:2008) To the end of 5.4.1 (after the compliance
statement) the following is added:
The screen of the cable distribution system is
normally not earthed at the entrance of the building
and there is normally no equipotential bonding
system within the building. Therefore the protective
earthing of the building installation need to be
isolated from the screen of a cable distribution
system.
It is however accepted to provide the insulation
external to the equipment by an adapter or an
interconnection cable with galvanic isolator, which
may be provided by e.g. a retailer.
The user manual shall then have the following or
similar information in Norwegian and Swedish
language respectively, depending on in what
country the equipment is intended to be used in:
“Equipment connected to the protective earthing of
the building installation through the mains
connection or through other equipment with a
connection to protective earthing – and to a cable
distribution system using coaxial cable, may in
some circumstances create a fire hazard.
Connection to a cable distribution system has
therefore to be provided through a device providing
electrical isolation below a certain frequency range
(galvanic isolator, see EN 60728-11)”
NOTE In Norway, due to regulation for installations of cable
distribution systems, and in Sweden, a galvanic isolator shall
provide electrical insulation below 5 MHz. The insulation shall
withstand a dielectric strength of 1,5 kV r.m.s., 50 Hz or 60 Hz,
for 1 min.
Translation to Norwegian (the Swedish text will also
be accepted in Norway):
“Utstyr som er koplet til beskyttelsesjord via
nettplugg og/eller via annet jordtilkoplet utstyr – og
er tilkoplet et kabel-TV nett, kan forårsake
brannfare. For å unngå dette skal det ved tilkopling
av utstyret til kabel-TV nettet installeres en
galvanisk isolator mellom utstyret og kabel-TV
nettet.”
Translation to Swedish:
”Utrustning som är kopplad till skyddsjord via jordat
vägguttag och/eller via annan utrustning och
samtidigt är kopplad till kabel-TV nät kan i vissa fall
medföra risk för brand.
Főr att undvika detta skall vid anslutning av
utrustningen till kabel-TV nät galvanisk isolator
finnas mellan utrustningen och kabel-TV nätet.”
Result - Remark
Verdict
N/A
Korea Testing Certification
Page 14 of 16
Report No.: W14-65-007
Attachment 1 - European group differences and national differences
(EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011)
IEC60065K - ATTACHMENT
Clause
Requirement + Test
13.3.1
NO: To the second paragraph the following is
added:
In Norway, due to the IT power distribution system
used, the a.c. MAINS supply voltage is considered
to be equal to the line-to-line voltage, and will
remain 230 V in case of a single earth fault.
Justification: Based on a use in Norway of an IT
power distribution system where the neutral is not
provided.
Result - Remark
Verdict
N/A
Denmark
15.1.1
(A11:2008) The text of the Danish SNC in EN 60065:2002 has
been modified as follows:
To the first paragraph the following is added:
In Denmark, supply cords of single-phase
appliances having a rated current not exceeding 13
A shall be provided with a plug according to the
Heavy Current Regulations Section 107-2-D1.
Appliances of CLASS I provided with socket-outlets
with earth contact or which are intended to be used
in locations where protection against indirect
contact is required according to the wiring rules
shall be provided with a plug in accordance with the
Heavy Current Regulations, Section 107-2-D1
standard sheet DK 2-1a.
To the second paragraph the following is added:
Socket outlets intended for providing power to
CLASS II apparatus with a rated current of 2,5 A
shall be in accordance with the Heavy Current
Regulation, Section 107-2-D1 standard sheet DKA
1-4a.
Other current ratings socket outlets shall be in
compliance with the Heavy Current Regulation,
Section 107-2-D1 standard sheet DKA 1-3a or DKA
1-3b.
To the third paragraph the following is added:
Mains socket-outlets with earthing contact shall be
in compliance with the Heavy Current Regulation,
Section 107-2-D1 standard sheet DK 1-3a, DK 1-5a
or DK 1-7a.
Justification: Heavy Current Regulations, Section
107-2-D1
N/A
15.1.1
N/A
IE: Apparatus which is fitted with a flexible cable or
cord shall be provided with a 13 A plug in
accordance with Statutory Instrument 525:97, “13 A
Plugs and Conversion Adapters for Domestic Use
Regulations:1997.
Justification: SI 525: 1997
Korea Testing Certification
Page 15 of 16
Report No.: W14-65-007
Attachment 1 - European group differences and national differences
(EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011)
IEC60065K - ATTACHMENT
Clause
Requirement + Test
15.1.1
NO: Mains socket-outlets mounted on CLASS II
apparatus shall comply with the specifications
given in CEE Publ. 7 as far as a applicable, with
the following amendments:
§ 8 Dimensions
a 2.5 A 250 V two-pole socket-outlets for electronic
apparatus shall comply with the enclosed Standard
Sheet I.
Result - Remark
Verdict
N/A
§ 24 Mechanical strength
A 2,5 A 250 V socket-outlets for CLASS II
electronic apparatus are tested as specified in
12.1.3 of EN 60065. Also the protecting rim shall be
tested
Justification: Act of 24 May 1929 relating to
supervision of electrical installation (TEA 1929/FEL
1998).
15.1.1
UK: Apparatus which is fitted with a flexible cable
or cord and is designed to be connected to a mains
socket conforming to BS 1363 by means of that
flexible cable or cord and plug shall be fitted with
a ”standard plug” in accordance with Statutory
Instrument 1768: 1994: The Plugs and Sockets etc.
(Safety) Regulations 1994, unless exempted by
those Regulations.
NOTE ”Standard plug” is defined in SI 1768:1994
and essentially means an approved plug
conforming to BS 1363 or an approved conversion
plug.
Justification: SI 1768: 1994
N/A
Korea Testing Certification
Page 16 of 16
Report No.: W14-65-007
Attachment 1 - European group differences and national differences
(EN 60065:2002+A1:2006+A11:2008+A2:2010+A12:2011)
IEC60065K - ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
J.2
NO: After Table J.1 the following is added:
In Norway, due to the IT power distribution system
used, the a.c. MAINS supply voltage is considered
to be equal to the line-to-line voltage, and will
remain 230 V in case of a single earth fault.
Justification: Based on a use in Norway of an IT
power distribution system where the neutral is not
provided.
ZC
ANNEX ZC TO EN 60065, A-DEVIATIONS (EN)
P
5.1
IT: Additional markings on the outside of the TV
receiver in Italian language
N/A
IT:User instructions in Italian language including a
conformity declaration
N/A
IT: Certification number on the back cover
N/A
6.1
DE: The following requirement applies:
For the operation of any cathode ray tube intended
for the display of visual images operating at an
acceleration voltage exceeding 40 kV, authorization
is required, or application of type approval
(Bauartzulassung) and marking.
Justification: German ministerial decree against
ionizing radiation (Röntgenverordnung), in force
since 2002-07-01, implementing the European
Directive 96/29/EURATOM.
NOTE Contact address:
Physikalisch-Technische Bundesanstalt,
Bundesallee 100, D-38116 Braunschweig, Tel.:
Int+49-531-592-6320, Internet: http://www.ptb.de
N/A
14
SE: Switches containing mercury such as
thermostats, relays and level controllers are not
allowed.
Justification: Ordinance (1990:944) on Prohibition
in Connection with handling. Importation and
exportation of Chemical Products (Certain Cases)
N/A
N/A
Korea Testing Certification
Page 1 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Argentina – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2007-05-29 in CB Bulletin)
Clause
Requirement + Test
-
- Ratings shall cover 220 Vac - 50 Hz
- Class 0 and Class 0I appliances are not allowed
- Safety instructions and manuals shall be written in
Spanish language (Resolution 92/98)
- Country of origin shall be shown on the marking
plate or, if not possible, in the primary packaging
(Resolution 92/98)
- Address of the importer in Argentina shall be
shown on the product or on the primary packaging
(Resolution 92/98)
- Class I appliances provided with plugs shall be
provided with the label specified in sheet "Class I"
(Disposition 731/87)
- Class II appliances provided with plugs shall be
provided with the label specified in sheet "Class II"
(Disposition 731/87)
- Plugs shall be in conformity with IRAM 2063
Standard for Class II appliances and IRAM 2073
Standard for Class I appliances (Resolution
524/98)
- Adaptors/Transformers provided with integrated
plugs shall be provided with blades which shall
meet the geometry of IRAM 2063 standard for
Class II appliances or IRAM 2073 standard for
Class I appliances (Resolution 524/98)
- Appliances certified under System Nº 4 (Type
Certification scheme) shall be marked with the
symbol specified in sheet "St Mark" (Resolution
197/04)
- Appliances certified under System Nº5 (Mark of
Conformity Certification scheme) shall be marked
with the symbols specified in sheet "S Mark"
(Resolution 799/99)
Result - Remark
Verdict
P
Korea Testing Certification
Page 2 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Australia – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2010-04-26 in CB Bulletin)
Clause
Requirement + Test
7.15
In Table 3 under item c) add an h) in both columns
against ‘thermoplastic materials’ and add the
following new footnote:
h
As an alternative to the method described in
footnote f) the following variation may be
used where there is any doubt about the
suitability of the material:
The ball-pressure test described in
AS/NZS 60695.10.2 may be carried out.
To assess compliance under normal
operating conditions, the test shall be made
in a heating cabinet at a temperature of
40°C ±2°C plus the maximum temperature
rise determined under normal operating
conditions but, it shall be at least
-
Result - Remark
Verdict
N/A
for external parts…75°C ±2°C
for materials supporting parts
conductively connected
to the mains……….125°C ±2°C
7.2
After the second paragraph, add the following:
The alternative method described in footnote h) of
Table 3 may be used.
N/A
15.1.1
After the second paragraph, add the following:
Plugs for the connection of apparatus to mainspowered socket-outlets shall comply with
AS/NZS 3112 or AS/NZS 3123. Apparatus with a
plug portion, suitable for insertion into a 10 A 3-pin
flat-pin socket-outlet complying with AS/NZS 3112,
shall comply with the requirements of AS/NZS 3112
for equipment with integral pins for insertion into
socket-outlets.
P
15.3.5
In Table 15, in the second and third rows of the first
column replace ‘6’ with ‘7.5’.
N/A
16.2
In Table 18, in the second and third rows of the first
column replace ‘6’ with ‘7.5’.
P
16.3
In item (b), add the following:
A flexible cord complying with AS/NZS 3191 need
not undergo this test.
N/A
19.201
Add the following after Clause 19.6:
19.201 Additional stability requirements for
television receivers
Television receivers and display devices that may
be used for television purposes, with a mass of 7kg
or more, shall have additional stability
requirements.
Compliance is checked by inspection and by the
tests of 19.201.2.2 and 19.201.3 as applicable.
Apparatus designed for only fixing to a wall, ceiling
N/A
Korea Testing Certification
Page 3 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Australia – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2010-04-26 in CB Bulletin)
Clause
Requirement + Test
or equipment rack are not required to be subjected
to these additional requirements if the marking of
5.4.1 f) is provided on or with the apparatus.
19.201.1 Warning notice
Television receivers and display devices that may
be used for television purposes, shall be provided
with information in the instructions for installation
for use, containing the following information or
similar:
IMPORTANT INFORMATION
If a television is not positioned in a sufficiently
stable location, it can be potentially hazardous
due to falling. Many injuries, particularly to
children, can be avoided by taking simple
precautions such as:
•
Using cabinets or stands recommended
by the manufacturer of the television.
•
Only using furniture that can safely
support the television.
•
Ensuring the television is not
overhanging the edge of the supporting
furniture.
•
Not placing the television on tall
furniture (for example, cupboards or
bookcases) without anchoring both the
furniture and the television to a suitable
support.
•
Not standing the televisions on cloth or
other materials placed between the
television and supporting furniture.
•
Educating children about the dangers of
climbing on furniture to reach the
television or its controls.
Such information should also be provided as a
label on the apparatus.
NOTE: The committee is considering a request
from Regulatory Authorities that providing the
information as a label on the apparatus should be
mandatory.
19.201.2 Restraining device
19.201.2.1 Television receivers should be
provided with a restraining device such as a fixing
point to facilitate restraining the television from
toppling forward.
NOTE: The committee is considering a request
from Regulatory Authorities that providing a
Result - Remark
Verdict
N/A
Korea Testing Certification
Page 4 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Australia – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2010-04-26 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
restraining device on the apparatus should be
mandatory.
19.201.2.2 Where a restraining device is provided
in accordance with 19.201.2.1 information shall be
provided in the instructions for installation or use, to
ensure correct and safe installation. Such
information should also be provided as a label on
the television receiver. Any such restraining device
shall be capable of withstanding a pull of 100 N in
all directions without damage.
19.201.3 Glass slide test
Television receivers and display devices that may
be used for television purposes, with a mass of 18
kg or more, are placed on a clean, dry, glass
covered horizontal surface such that only the
supporting feet are in contact with the glass. The
glass-covered surface is then tilted in the most
unfavourable direction through an angle of 10°.
During the tests, the equipment shall not slide.
Verdict
20
Add the following after NOTE 2:
For alternative test refer to Clause 20.201.
20.1.4
In Table 21, in the third and fourth columns change
both ‘HB75’ and ‘No requirement’ to ‘V-1’.
P
20.2.3
After this Clause, add the following variation:
20.201 Resistance to fire—Alternative tests
20.201.1 General
Parts of non-metallic material shall be resistant to
ignition and the spread of fire.
This requirement does not apply to decorative
trims, knobs and other parts unlikely to be ignited
or to propagate flames originating from inside the
apparatus, or the following:
a)
Components that are contained in an
enclosure having a flammability category
of V-0 according to AS/NZS 60695.11.10
and having openings only for the
connecting wires filling the openings
completely, and for ventilation not
exceeding 1 mm in width regardless of
length.
b)
The following parts which would contribute
negligible fuel to a fire:
small mechanical parts, the mass
of which does not exceed 4 g, such
as mounting parts, gears, cams,
belts and bearings;
small electrical components, such
as capacitors with a volume not
exceeding 1 750 mm3, integrated
circuits, transistors and optocoupler
N/A
N/A
Korea Testing Certification
Page 5 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Australia – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2010-04-26 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
packages, if these components are
mounted on material of
flammability category V-1 or better
according to AS/NZS 60695.11.10.
NOTE – In considering how to minimize
propagation of fire and what ‘small parts’ are,
account should be taken of the cumulative effect of
small parts adjacent to each other for the possible
effect of propagating fire from one part to another.
Compliance shall be checked by the tests of
20.201.2.1, 20.201.2.2. and 20.201.2.3
For the base material of printed boards, compliance
shall be checked by the test of 20.201.2.4.
The tests shall be carried out on parts of nonmetallic material which have been removed from
the apparatus. When the glow-wire test is carried
out, they are placed in the same orientation as they
would be in normal use.
These tests are not carried out on internal wiring.
20.201.2 Tests
20.201.2.1 Testing of non-metallic parts
Part of non-metallic material shall be subject to the
glow-wire test of AS/NZS 60695.2.11 which shall
be carried out at 550°C.
Parts for which the glow-wire test cannot be carried
out, such as those made of soft or foamy material,
shall meet the requirements specified in ISO 9772
for category FH-3 material. The glow-wire test shall
not be carried out on parts of material classified at
least FH-3 according to ISO 9772 provided that the
sample tested was not thicker than the relevant
part.
20.201.2.2 Testing of insulated parts
Part of insulating material supporting potential
ignition sources shall be subject to the glow-wire
test of AS/NZS 64695.2.11 which shall be carried
out at 750°C.
The test shall be also carried out on other parts of
insulating material which are within a distance of
3 mm of the connection
NOTE – Contacts in components such as switch
contacts are considered to be connections.
For parts which withstand the glow-wire test but
produce a flame, other parts above the connection
within the envelope of a vertical cylinder having a
diameter of 20 mm and a height of 50 mm shall be
subjected to the needle-flame test. However, parts
shielded by a barrier which meets the needle-flame
test need not be tested.
The needle-flame test shall be made in accordance
with AS/NZS 4695.2.2 with the following
modifications:
Verdict
Korea Testing Certification
Page 6 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Australia – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2010-04-26 in CB Bulletin)
Clause
Requirement + Test
Clause of
AS/NZS 4695.2
.2
Change
5 Severities
Replace with:
The duration of application of
the test flame shall be
30 s ±1 s.
8 Test
procedure
8.2
Replace the first sentence
with:
The specimen shall be
arranged so that the flame
can be applied to a vertical or
horizontal edge as shown in
the examples of figure 1.
8.4
The first paragraph does not
apply.
Addition:
If possible, the flame shall be
applied at least 10 mm from
a corner.
8.5
Replace with:
The test shall be made on
one specimen. If the
specimen does not withstand
the test, the test may be
repeated on two further
specimens, both of which
shall then withstand the test
10 Evaluation
of test results
Replace with:
The duration of burning (tb)
shall not exceed 30 s.
However, for printed circuit
boards, it shall not exceed
15 s.
The needle-flame test shall not be carried out on
parts of material classified as V-0 or V-1 according
to AS/NZS 60695.11.10 provided that the sample
tested was not thicker than the relevant part.
20.201.2.3 Testing by needle-flame test
If parts, other than enclosures, do not withstand the
glow wire tests of 20.201.2.2, by failure to
extinguish within 30 s after the removal of the glowwire tip, the needle-flame test detailed in
20.201.2.2 shall be made on all parts of nonmetallic material which are within a distance of
50 mm or which are likely to be impinged upon by
Result - Remark
Verdict
Korea Testing Certification
Page 7 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Australia – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2010-04-26 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
flame during the tests of 20.201.2.2. Parts shielded
by a separate barrier which meets the needle-flame
test shall not be tested.
NOTE 1 – If the enclosure does not withstand the
glow-wire test the appliance is considered to have
failed to meet the requirements of Clause 21.201
without the need for consequential testing.
NOTE 2 – If other parts do not withstand the glowwire test due to ignition of the tissue paper and if
this indicates that burning or glowing particles can
fall onto an external surface underneath the
apparatus, the apparatus is considered to have
failed to meet the requirements of Clause 21.201
without the need for consequential testing
NOTE 3 – Parts likely to be impinged upon by the
flame are considered to be those within the
envelope of a vertical cylinder having a radius of
10 mm and a height equal to the height of the
flame, positioned above the point of the material
supporting, in contact with, or in close proximity to,
connections.
20.201.2.4 Testing of printed boards
The base material of printed boards shall be
subject to the needle-flame test of
Clause 21.201.2.3. The flame shall be applied to
the edge of the board where the heatsink effect is
lowest when the board is positioned as in normal
use. The flame shall not be applied to an edge
consisting of broken perforations, unless the edge
is less than 3 mm from a potential ignition source.
The test is not carried out if the—
printed board does not carry any potential
ignition source;
base material of printed boards, on which
the available power at a connection
exceeds 15 VA operating at a voltage
exceeding 50 V and equal or less than
400 V (peak) a.c. or d.c. under normal
operating conditions, is of flammability
category V-1 or better according to
AS/NZS 60695.11.10, or the printed
boards are protected by an enclosure
meeting the flammability category V-0
according to AS/NZS 60695.11.10, or
made of metal, having openings only for
connecting wires which fill the openings
completely; or
base material of printed boards, on which
the available power at a connection
exceeds 15 VA operating at a voltage
exceeding 400 V (peak) a.c. or d.c. under
normal operating conditions, and base
material of printed boards supporting spark
Verdict
Korea Testing Certification
Page 8 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Australia – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2010-04-26 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
gaps which provides protection against
overvoltages, is of flammability category V0 according to AS/NZS 60695.11.10 or the
printed boards are contained in a metal
enclosure, having openings only for
connecting wires which fill the openings
completely.
Compliance shall be determined using the smallest
thickness of the material.
NOTE – Available power is the maximum power
which can be drawn from the supplying circuit
through a resistive load whose value is chosen to
maximize the power for more than 2 min when the
circuit supplied is disconnected.
21.201.3 For open circuit voltages greater than
4 kV
Potential ignition sources with open circuit voltages
exceeding 4 kV (peak) a.c. or d.c. under normal
operating conditions shall be contained in a fire
enclosure which shall comply with flammability
category V-1 or better according to
AS/NZS 60695.11.10.
Annex B
After the heading add:
For Australia only, this Annex is replaced by the
requirements of the Telecommunications Labelling
Notice issued under the Telecommunications Act.
NOTE – The Telecommunications Act is
administered by the Australian Communications
Authority.
Verdict
N/A
Korea Testing Certification
Page 9 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Canada – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2008-05-01 in CB Bulletin)
Clause
Requirement + Test
1.1.1
Add the following paragraph and note:
Result - Remark
Verdict
P
This Standard applies to the safety of such
equipment designed to be installed and used in
accordance with the rules of the Canadian
Electrical Code (CEC), Part I.
Note 4A: Manufacturers designing products for use
in Canada may find a helpful summary of the
equipment-related requirement of the CEC, Part I,
in CSA SPE-2000.
1.2
Normative references
P
Where reference is made to CSA Publications,
such reference shall be considered to refer to the
latest edition and all amendments published to that
edition. This Standard refers to the following
Standards, and the years shown indicate the latest
editions available at the time of printing.
ANSI/IEEE Standard
C62.1-1984, Surge Arresters for AlternatingCurrent Power Circuits
CSA Standards
C22.1-02, Canadian Electrical Code, Part 1
CAN/CSA-C22.2 No. 0-M91 (R2001), General
Requirements - Canadian Electrical Code, Part II
C22.2 No. 0.4-M1982 (R1999), Bonding and
Grounding of Electrical Equipment (Protective
Grounding)
C22.2 No. 0.15-01, Adhesive Labels
CAN/CSA-C22.2 No. 1-98, Audio, Video and
Similar Electronic Equipment
CAN/CSA-C22.2 No. 21-95 (R1999), Cord Sets
and Power Supply Cords
C22.2 No. 39-M1987 (R1999), Fuseholder
Assemblies
C22.2 No. 42-99, General Use Receptacles,
Attachment Plugs, and Similar Wiring Devices
CAN/CSA-C22.2 No. 49-98, Flexible Cords and
Cables
CAN/CSA-C22.2 No. 94-M91 (R2001), Special
Purpose Enclosures
C22.2 No. 127-99, Equipment and Lead Wires
C22.2 No. 209-M1985 (R1999), Thermal Cut-Offs
CAN/CSA-C22.2 No. 210.2-M90 (R2001),
Appliance Wiring Material Products
CAN/CSA-C22.2 No. 223-M91 (1999), Power
Supplies with Extra-Low-Voltage Class 2 Outputs
1.2
(Cont'd)
CAN/CSA-C22.2 No. 228-92 (1999), Cathode Ray
Tubes
CAN/CSA-C22.2 No. 248.14-00, Low Voltage
N/A
Korea Testing Certification
Page 10 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Canada – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2008-05-01 in CB Bulletin)
Clause
Requirement + Test
Fuses - Part 14
Result - Remark
Verdict
Spe-2000-94, Guide for Electrical Equipment for
Installation and Use in Canada
IEC Standards
60038:2002, IEC standard voltages
60083:1975, Plug and socket-outlets for domestic
and similar general use.
60173:1964, Colours of the cores of flexible cables
and cords.
60320 (all parts), Appliance couplers for household
and similar general purposes.
60707:1981, Methods of test for the determination
of the flammability of solid electrical insulating
materials.
60884 (all parts), Plugs and socket-outlets for
household and similar purposes.
60906-1:1986, IEC System of plugs and socketoutlets for household and similar purposes - Part 1:
Plugs and socket-outlets 16A 250V ac.
60906-2:1997, IEC System of plugs and socketoutlets for household and similar purposes - Part 2:
Plugs and socket-outlets 15A 125V ac.
60906-3:1994, IEC System of plugs and socketoutlets for household and similar purposes - Part 3:
SELV plugs and socket-outlets 16A 6V, 12V, 24V,
48V ac and dc.
3.2A
Add the following clause:
N/A
A component power supply complying with
CAN/CSA-C22.2 No. 60950 is considered to
comply with this construction and fault conditions of
this Standard after taking into account any relevant
conditions of acceptability.
4.2.1
Add the following after the fifth paragraph:
P
For apparatus intended for use at nominal 120V ac,
the apparatus shall comply with this standard at
supply voltages between 108V and 125V. For
apparatus intended for use at nominal 240V ac the
apparatus shall comply with this standard at supply
voltages between 216V and 250V.
4.2.10
Add the following after the second paragraph:
N/A
As an alternative, a supply apparatus for general
use complying with CSA/CSA-C22.2 No. 223 or
CAN/CSA-C22.2 No. 60950 shall be acceptable.
5
Markings and instructions – adhesive
nameplates
Add the following paragraph:
Adhesive nameplates on commercial products shall
P
Korea Testing Certification
Page 11 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Canada – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2008-05-01 in CB Bulletin)
Clause
Requirement + Test
comply with CSA C22.2 No 0.15.
5.1
Add the following item:
Result - Remark
Verdict
P
j) Date of manufacture: a date or code identifying
the period of manufacture shall be marked on the
apparatus;
5.3A
Add the following clause:
N/A
Where a loudspeaker grille, removable from the
outside, is relied on as part of the enclosure (see
Clause 9.2), the following marking or equivalent
shall be visible on the enclosure after removal of
the grille:
"Caution - To prevent electric shock hazard,
replace grille."
Alternatively, the symbol in Clause 5.2 b) shall be
visible after removal of the grille, and the caution
wording above shall appear in the user instructions,
accompanied by the symbol.
Compliance is checked by inspection.
8.9
Add the following title to this clause:
P
Mains Wiring
Add the following paragraph:
Wiring in circuits with voltages higher than 42V
peak shall comply with CSA C22.2 No 127 or
CAN/CSA C22.2 No. 210.2.
9.1.1A
Class I Apparatus Leakage
Add the following Clause:
N/A
For cord-connected Class I apparatus, the leakage
current through the safety earthing conductor
expressed as voltages U1 and U2 shall not exceed
U1 = 105V (peak) and U2 = 1.05V (peak) (1.5mA).
Apparatus having a leakage current between 0.75
mA and 1.5 mA shall be provided with a caution
label on the mains cord with the following, or
equivalent:
"CAUTION - TO REDUCE THE RISK OF
ELECTRIC SHOCK, GROUNDING OF THE
CENTRE PIN OF THIS PLUG MUST BE
MAINTAINED".
9.1.1.2
Determination of accessible parts – loudspeaker
enclosure parts
Add the following after the fourth paragraph:
Moving parts of loudspeaker systems, such as dust
caps or cones of drivers or passive radiators are
not regarded as preventing accessibility.
N/A
Korea Testing Certification
Page 12 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Canada – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2008-05-01 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
Verdict
NOTE 1A: See also Clause 13.3.1
9.2
Removal of protective covers – loudspeaker
grilles
Add the following after the second paragraph:
N/A
This requirement applies also to internal parts of
loudspeaker systems that become accessible by
removal of a loudspeaker grille from the outside
either by hand or with the use of a tool, coin, or
other object. In such cases, the apparatus shall be
marked according to Clause 5.3A.
Replace the third paragraph with the following:
Compliance is checked by inspections and by
application of the tests of Clause 9.1.1, except that
the measurements are made 2s after removal of
the cover or grille.
10.2A
Enclosure type designation and use – outdoor
enclosure
N/A
Add the following clause:
If equipment is installed in environments where the
enclosure is required to prevent ingress of water or
dust, the enclosure shall be classified as a type
recognized by the Canadian Electrical Code, Part I,
and shall comply with the requirements of
CSA/CSA-C22.2 No. 94.
11.2
Heating – flammable gases
N/A
Add the following clause:
Flammable gases shall not be emitted from a
component for more than 10 secs.
12.3A
Television Impacts
N/A
12.3A.1
Television Impact Test: For television sets and
similar apparatus using a cathode ray tube larger
than 160mm diagonally, the top, sides, front and
rear of the enclosure, including the safety screen
where provided, shall be capable of withstanding a
single impact of 7J in accordance with Clause
12.3A.2 without developing any opening larger than
2
130mm in the enclosure of the cathode ray tube
unless the minor dimension of any opening is not
more than 7mm.
N/A
When applied to a safety screen, the impact shall
neither result in damage to its mounting to the
extent it is mechanically unsuitable for reuse nor
shall tempered glass, if used, be cracked.
When applied to the face of a directly viewed
Korea Testing Certification
Page 13 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Canada – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2008-05-01 in CB Bulletin)
Clause
Requirement + Test
cathode ray tube, the impact shall not develop any
opening in the face of the tube. Scaling and
cracking of the glass is permissible. A cathode ray
tube that has been shown to comply with
CAN/CSA-C22.2 No 228 or CAN/CSA-E61965
shall be considered acceptable with no further
tests.
12.3A.2
Television Impact Object:
Result - Remark
Verdict
N/A
The impact specified in Clause 12.3A.1 shall be
caused by allowing a solid, smooth, steel sphere
51mm in diameter and weighing approximately
0.5kg to strike the enclosure with the specified
impact in a direction perpendicular to the enclosure
surface. If deemed necessary, the enclosure shall
be tested with the proper cathode ray tube
mounted.
13.3
Clearances
N/A
13.3.1
General – loudspeaker voice coil
N/A
Add the following after the third paragraph:
CLEARANCES between a loudspeaker voice coil
and adjacent conductive parts shall be disregarded.
14.2
Capacitors and RC-units
P
14.2.1
(Y-Capacitors)
Add the following paragraph:
P
As an alternative an isolating capacitor complying
with applicable requirements of CSA C22.2 No 1,
shall be acceptable for bridging BASIC or
SUPPLEMENTARY INSULATION.
14.2.2
(X-Capacitors)
Add the following paragraph:
P
As an alternative an across-line capacitor
complying with applicable requirements of CSA
C22.2 No 1, shall be acceptable.
14.5.1.2
Thermal releases
Add the following paragraph:
N/A
As an alternative a THERMAL LINK complying with
CSA C22.2 No 209 shall be acceptable.
14.5.2
Fuse-links and fuse holders
P
14.5.2.1
Add the following paragraph:
P
As an alternative, a fuse-link complying with CSA
C22.2 No 248.14 shall be acceptable.
14.5.2.4
Add the following paragraph:
As an alternative a Fuseholder Assembly
complying with CSA C22.2 No 39 shall be
acceptable.
P
Korea Testing Certification
Page 14 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Canada – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2008-05-01 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
Verdict
14.6
Switches
P
14.6.1 to
14.6.5
Add the following to each of the Clauses:
P
14.11
Optocouplers
Add the following paragraph:
As an alternative, a TV-Rated Switch complying
with CSA C22.2 No 1-98, Cl 9 shall be acceptable.
P
As an alternative, an optocoupler complying with
CSA C22.2 No. 1 shall be acceptable.
14.12
Surge suppression varistors
Add the following paragraph:
P
As an alternative, a varistor complying with CSA
C22.2 No. 1 shall be acceptable.
14.12A
Gas discharge tubes
Add New Clause 14.12A:
N/A
Gas discharge tubes complying with the following
tests may be connected to bridge BASIC or
REINFORCED INSULATION.
Ten samples of gas discharge tubes isolating the
ac supply from exposed parts shall be subjected to
the varistor pulse tests of Clause 14.12. Following
the pulses, the device shall be allowed to return to
room temperature. The dielectric breakdown
voltage of the gas tube shall not decrease by more
than 50% and the gas discharge tube shall comply
with the electric strength test of Clause 10.3, with
the test voltage reduced to twice the mains voltage.
15.1
Plugs and sockets
N/A
15.1.1
(Convenience Receptacle Type)
Add the Following Clause:
N/A
A receptacle provided for general purpose mains
output shall comply with the requirements of CSA
Standard C22.2 No 42 (dimensional requirements
are also specified in IEC 60906-2). The attachment
plug cap shall be polarized type when the
apparatus is provided with a manually operated,
MAINS connected single pole switch for apparatus
on-off operation, a socket screwshell lampholder,
or a 15 or 20 A socket outlet.
15.1.2
(Audio Terminals)
Add the following paragraph:
N/A
Banana plugs shall be acceptable.
15.1.3
Adapter output connectors
Replace the first paragraph with the following:
Terminals and connectors used in output circuits of
supply apparatus, whose output is not a standard
nominal mains voltage according to IEC 60038,
N/A
Korea Testing Certification
Page 15 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Canada – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2008-05-01 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
Table 1, shall not be compatible with those
specified for household and similar general
purposes, for example those described in IEC
60083[1], IEC 60320, IEC 60884, IEC 60906 (parts
1, 2, and 3), and CSA C22.2 No 42.
15.2
Provisions for protective earthing - Bond
Impedance
Replace the third paragraph with the following:
Verdict
N/A
Earthing connections shall comply with the test
requirements of CSA C22.2 No 0.4.
15.3
Terminals for external flexible cords and permanent connections to the mains
supply
N/A
15.3.1A
(Permanent Wiring)
Add the following clauses:
N/A
Equipment intended for permanent connection to
the mains shall have provisions for connection to
the wiring system in accordance with the Canadian
Electrical Code, Part I.
15.4.2
The terminal parts and all other provisions for
permanent connection to fixed wiring shall comply
with CSA Standard CAN/CSA-C22.2 No 0.
N/A
(Mains Plugs – Type)
Add the following paragraphs:
N/A
Mains plugs of non-permanently installed
equipment shall comply with:
a)
CSA C22.2 No 21 for moulded-on type
attachment plugs; and
b)
CSA C22.2 No 42 for disassembly type
attachment plugs (dimensional requirements are
also specified in IEC 60906-2).
Class II equipment provided with a general purpose
mains outlet, or lampholder, shall be provided with
a polarized-type plug.
N/A
If the plug is a polarized type, single pole switches
or over current protectors shall not be connected in
the identified conductor.
N/A
16
External flexible cords
N/A
16.1
Replace this clause with the following:
N/A
Flexible cord used for mains supply shall comply
with the requirements of CSA C22.2 No 49. The
cord type shall be in accordance with Table 4 of
CSA C22.2 No 1.
The attachment plug shall be rated not less than
125% of the apparatus rated current.
Cord sets shall comply with the requirements of
CSA C22.2 No 21.
Non-detachable flexible cables and cords of Class I
Korea Testing Certification
Page 16 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Canada – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2008-05-01 in CB Bulletin)
Clause
Requirement + Test
apparatus shall be provided with a green/yellow
core connected to the protective earthing terminal
of the apparatus and, if a plug is provided, to the
protective earthing contact of the plug.
Result - Remark
Verdict
Compliance is checked by inspection.
Note: The colour of cores of flexible mains cords is
contained in IEC 60173[4].
17.9A
Adhesive securement and conductive coatings
N/A
17.9A.1
Add the following clause:
N/A
Adhesive securement
The following parts, the displacement of which may
result in a fire or shock hazard, shall not be
secured solely by adhesive, unless the adhesive
system complies with the resistance to external
forces test of Clause 9.1.7, the bump test of Clause
12.1.1, and the impact test of Clause 12.1.3, after
conditioning in accordance with Clause 17.9A.2:
a) internal metal parts/conductive coatings;
b) barriers; and
c) required enclosure parts.
Note: Cathode ray tubes are excluded from this
test.
17.9A.2
Adhesive and conductive coating securement conditioning
N/A
17.9A.2.1
General:
N/A
Where required by Clause 17.9A.1, one sample of
the apparatus or enclosure section shall be
conditioned in accordance with the requirements of
Clause 17.9A.2.2. Equivalent ageing test data
supplied by the manufacturer will be considered in
lieu of ageing.
17.9A.2.2
Ageing
Day 1: Place in oven at 100 ± 1ºC for 1 week, or
82 ± 1ºC for 8 weeks at the manufacturer’s option.
Day 8 or Day 57:
1. Remove from oven and leave at room
temperature for 1 h.
2. Place in freezer at –35ºC for 2 h.
3. Remove from freezer and allow to reach room
temperature overnight.
Day 9 or Day 58:
1. Place in a compartment at 96% relative humidity
for 3 h.
2. Remove and leave at room temperature and
humidity for 1 h.
3. Place in over at a temperature selected in the
first cycle for 3 h.
4. Remove and allow to come to room temperature
overnight.
N/A
Korea Testing Certification
Page 17 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Canada – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2008-05-01 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
Verdict
Day 10 or Day 59:
1. Place in freezer at –35ºC for 2 h.
2. Remove and leave at room temperature for 1 h.,
3. Place in humidity chamber at 96% relative
humidity for 3 h.
4. Remove and allow to come to room temperature
overnight.
Day 11 or Day 60:
1. Place in oven at the temperature selected in the
first cycle for 3 h.
2. Remove for 1 h.
3. Place in freezer at –35ºC for 2 h.
4. Remove and allow to come to room temperature
overnight.
Day 12 or Day 61:
1. Place in humidity chamber at 96% relative
humidity for 3 h.
2. Remove and perform mechanical tests as
required by Clause 17.9A.1
as applicable.
18
Mechanical strength of picture tubes and protection against the effects of
implosion
N/A
18.1A
(Cathode Ray Tubes)
Add the following clause:
N/A
A picture tube with a maximum face dimensions
exceeding 75mm either shall be intrinsically
protected with respect to effects of implosion and to
mechanical impact, in accordance with CAN/CSA
C22.2 No 228 or CAN/CSA E61965, or the
enclosure of the apparatus shall provide adequate
protection against the effects of an implosion of the
tube (see Clause 12).
19
Stability and Mechanical Hazards
Add the following after the second paragraph:
N/A
The test of 19.3 is only required for:
a) Apparatus with a mass of 25 kg or more; or
b) Apparatus, excluding loudspeaker systems,
with a height of 1m or more; or
c) Apparatus, including loudspeaker systems, in
combination with a supplied or recommended
cart of stand with a total height of 1m or more.
Add the following paragraph:
Apparatus not tested because it is intended to be
fastened in place shall be provided with the
following warning, marked on the apparatus or on a
durable label attached to the mains cord:
“WARNING: This apparatus must be securely
attached to the floor /wall per installation
instructions. Tipping, shaking, or rocking the
N/A
Korea Testing Certification
Page 18 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Canada – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2008-05-01 in CB Bulletin)
Clause
Requirement + Test
machine may cause injury / death”
Result - Remark
Verdict
20
Fire enclosure
N/A
20.2.1A
(Projector Lamp Enclosure)
Add the following clause:
N/A
Enclosures of apparatus containing high voltage or
projection lamps shall have a minimum flammability
rating of category FV1 according to IEC 60707 at
the minimum thickness used.
Annex B
Apparatus to be connected to the
telecommunications networks
Replace this annex with the following:
Apparatus intended for direct connection to a
TELECOMMUNICATION NETWORK shall comply
with:
a) Clause 19 of CSA C22.2 No 1; or
b) CAN/CSA C22.2 No. 60950.
N/A
Korea Testing Certification
Page 19 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
China – National Differences to IEC 60065:2005
(Test results according to last modification date 2012-06-06 in CB Bulletin)
Clause
Requirement + Test
1.1.3
Amended the first paragraph:
This standard applies to apparatus intended to be
used basically at altitudes not exceeding 5 000 m,
dry climate at warm temperate zone or tropical
climates.
The fourth paragraph replaced by following:
For apparatus intended to be used in vehicles,
ships or aircraft, or at altitudes exceeding
5 000m, additional requirements may be
necessary.
5
At the end of the first paragraph ,added following:
For apparatus intended to be used at altitude not
exceeding 2000m, a warning label containing the
following or a similar appropriate wording or a
symbol as in annex R(see following) shall fixed to
the equipment at readily visible place.
"Only used at altitude not exceeding 2000m."
Result - Remark
Verdict
P
N/A
P
If only symbol used, the explanation of the symbol
shall be contained in the instruction manual.
For apparatus intended to be used in not-tropical
climate regions, a warning label containing the
following or a similar appropriate wording or a
symbol as in annex R shall fixed to the equipment
at readily visible place.
"Only used in not-tropical climate regions."
If only symbol used, the explanation of the symbol
shall be contained in the instruction manual.
The statements above shall be given in a language
acceptable to the regions where the apparatus is
intended to be used.
5.1 e)
After the last paragraph, added:
N/A
…….For single rated voltage, “220 V” or threephase “380V” shall be marked only. For a rating
range, 220 V or three-phase 380V shall be
covered. For multiple rated voltages, one of them
shall be 220 V or three-phase 380V and which
default setting from manufacture shall be 220 V or
three-phase 380V as well.
5.1 f)
After the first sentence, Added:
P
Korea Testing Certification
Page 20 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
China – National Differences to IEC 60065:2005
(Test results according to last modification date 2012-06-06 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
Verdict
……for Rated MAINS frequency or frequency
range shall be 50Hz or covered 50Hz.
5.4
Replaced the second sentence of the first
paragraph:
P
This information shall be given in normative
Chinese.
5.4.1i)
Added new paragraph i),after the h) paragraph:
i) For apparatus incorporating antenna coaxial
sockets witch is non-separated with CATV network,
a warning wording or a similar shall be given in the
instructions manual:
“The CATV network connecting to this apparatus
shall separate from protective earth, otherwise it
may cause fire or other hazard.”
N/A
7 ,Table3
Note a) of table 3 replaced:
This standard applies to apparatus intended to be
used in tropical climates, permissible temperature
rises are 10 K less than those specified in the table.
For apparatus intended to be used in non-tropical
climates the limits in Table 3 are satisfactory.
N/A
7.1
Added Note 3:
For apparatus intended to be operated at altitudes
between 2 000m and 5 000m, temperature
measuring conditions and maximum temperature
limits are under consideration.
N/A
9.1.1.1
Delete the note 3 and renumber the existing note 4
as 3.
N/A
9.1.1.1
After the paragraph of d), added a paragraph:
For apparatus intended to be used in tropical
climates, the limits should be halved than the
values given in a) and b) above.
N/A
10
Added a paragraph after the second paragraph :
The Insulation resistance between CATV antenna
coaxial sockets and protective earth of apparatus
shall comply with BASIC INSULATION. If it’s
possible that CLASS II apparatus with CATV
antenna coaxial sockets connect with protective
earth of another CLASS I apparatus by other
terminals, the insulation resistance between them
shall comply with BASIC INSULATION as well.
Added Note:
if antenna cable separated from the protective
earth before connection to the apparatus, there is
no requirements of Insulation resistance between
them but 5.4.1i) requirements shall be meet.
N/A
10.1
Delete “on CLASS II apparatus” in the first
paragraph.
N/A
10.2
Replaced the fifth to seventh paragraphs by the
N/A
Korea Testing Certification
Page 21 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
China – National Differences to IEC 60065:2005
(Test results according to last modification date 2012-06-06 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
following:
The humidity treatment is carried out in a chamber
containing air with a relative humidity of 93%±3 %.
Verdict
For apparatus, temperature of 40℃±2℃ and a
relative humidity of 93%±3% shall be subjected.
Apparatus intended to be used in non-tropical
climates are subjected to a relative humidity of 93%
±3%.
The temperature in the chamber, at all places
where samples located, shall be maintained within
2℃of any convenient value between 20℃ and
30℃, as long as no condensation occur.
Added Note 4: For apparatus intended to be
operated at altitudes between 2 000m and 5 000m ,
the requirements for treatment of the insulating
material are under consideration.
N/A
11.1
Delete note 2.
N/A
11.1
After the ninth paragraph added a paragraph:
For apparatus intended to be used in tropical
climates, halve the values given above.
N/A
12.5
Amended the first paragraph :
Antenna coaxial sockets to be mounted on the
apparatus shall subject to mechanical stress
caused in use, and the sockets incorporate with
parts or components which isolated HAZARDOUS
LIVE parts from ACCESSIBLE parts or protective
earth from other terminals.
N/A
13.3.2
After the first paragraph, added a paragraph:
The requirements apply to apparatus intended to
be used at altitude not exceeding 2 000 m . For
apparatus intended to be operated at altitudes
between 2 000m and 5 000m , Minimum
CLEARANCE limits shall multiply with multiplication
factor 1.48 in table A.2 of GB/T 16935.1. For
apparatus intended to be operated at altitude more
than 5 000m , Minimum CLEARANCES limit shall
multiply with relevant multiplication factor in table
A.2 of GB/T 16935.1.
N/A
Table 8、
Table 9、
Table1 0
Bellow the headings of Table 8 Table 9 and Table
10 ,added :
13.3.3
P
“(Applicable for altitude up to 2000m)” .
Amended Table 9 Note 2:
For operating voltage values exceeding of table 8,
extrapolation is permitted.
P
After the first paragraph, added a paragraph:
The requirements in table 10 apply to apparatus
intended to be used at altitude not exceeding 2 000
m. For apparatus intended to be operated at
N/A
Korea Testing Certification
Page 22 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
China – National Differences to IEC 60065:2005
(Test results according to last modification date 2012-06-06 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
altitudes between 2 000m and 5 000m , Minimum
CLEARANCE limits shall multiply with multiplication
factor 1.48 in table A.2 of GB/T 16935.1. For
apparatus intended to be operated at altitude more
than 5 000m , Minimum CLEARANCES limit shall
multiply with corresponding multiplication factor in
table A.2 of GB/T 16935.1.
Verdict
15.1.1
After the first paragraph, added a paragraph:
Plugs connected to the MAINS in apparatus shall
comply with GB 1002 or GB 1003.
18
Delete the first paragraph except the first sentence.
N/A
18.1
Replaced contents of two dashes in the fourth
paragraph:
N/A
P
——for intrinsically protected tubes, including those
having integral protective screens, compliance
is checked according to GB27701.
——for tubes non-intrinsically protected checked by
18.2.
18.2
Delete clause 18.2 and renumber the existing
clause 18.3 as 18.2.
N/A
Annex J.6
After the first paragraph, added a paragraph:
For apparatus intended to be operated at altitudes
between 2 000m and 5 000m, the Minimum
CLEARANCES in table J.2 shall multiply with
multiplication factor 1.48 in table A.2 of GB/T
16935.1. For apparatus intended to be operated at
altitude more than 5 000m, Minimum
CLEARANCES shall multiply with corresponding
multiplication factor in table A.2 of GB/T 16935.1.
N/A
Delete note 3 of table J.6.
N/A
Added annex R:
(normativ Instructions for the new safety warning labels.
e)
Annex R
R.1 Altitude warning label
Meaning of the label: Evaluation for apparatus only
based on altitude not exceeding 2000m, therefor
it’s the only operating condition applied for the
equipment .There may be some potential safety
hazard if the equipment is used at altitude above
2000m .
R.2 Climate warning label
N/A
Korea Testing Certification
Page 23 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
China – National Differences to IEC 60065:2005
(Test results according to last modification date 2012-06-06 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
Verdict
Meaning of the label: Evaluation for apparatus only
based on temperate climate condition, therefor it’s
the only operating condition applied for the
equipment .There may be some potential safety
hazard if the equipment is used in tropical climate
region.
Annex S
(informativ
e)
Added annex S:
Illustration relative to safety explanation in
normative Chinese、Tibetan、Mongolian、
Zhuang Language and Uighur.
N/A
Korea Testing Certification
Page 24 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Denmark – National Differences to IEC 60065:2001+A1:2005+A2:2010
(Test results according to last modification date 2011-03-14 in CB Bulletin)
Clause
Requirement + Test
3.Z1
Denmark
A new Danish national deviation has been
introduced by EN 60065/A2:2010:
Add to the end of the subclause
Due to many existing installations where the
socket-outlets can be protected with
fuses with higher rating than the rating of the
socket-outlets the protection for
pluggable equipment type A shall be an integral
part of the equipment.
Justification:
In Denmark an existing 13 A socket outlet can be
protected by a 20 A fuse.
Result - Remark
Verdict
N/A
Korea Testing Certification
Page 25 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Finland – National Differences to IEC 60065:2001+A1:2005+A2:2010
(Test results according to last modification date 2010-12-20 in CB Bulletin)
Clause
Requirement + Test
5.3
Amendment A2 (2010)
5.3 To the end of the subclause the following is
added:
CLASS I apparatus which is intended for
connection to the building installation wiring
via a plug or an appliance coupler, or both and in
addition is intended for connection
to other apparatus or a network shall, if safety
relies on connection to protective earth
or if surge suppressors are connected between the
network TERMINALS and
ACCESSIBLE parts, have a marking stating that
the apparatus must be connected to an
earthed MAINS socket-outlet.
The marking text in the applicable countries shall
be as follows:
In Finland: "Laite on liitettävä suojakoskettimilla
varustettuun pistorasiaan"
“Apparaten skall anslutas till jordat uttag”
Result - Remark
Verdict
N/A
Korea Testing Certification
Page 26 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Germany – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2007-05-29 in CB Bulletin)
Clause
Requirement + Test
5
The following markings are required:
a) In case of intrinsically ionizing radiation safe
cathode-ray tubes with accelerating voltages
between 20 Kv and 30 Kv:
- On the cathode-ray tube itself the wording:
Eigensicheere Kathodenstrahlröhre nach
Anlage III Röntgen-verordnung.
- Inside the apparatus:
the maximum allowed accelerating voltage in
Kv, and the maximum allowed beam current in
Ma.
- On the outer of the apparatus:
a notice in German language that produced Xrays are sufficiently shielded by the intrinsically
safe cathode-ray tube.
Result - Remark
Verdict
N/A
b) In case of approval of the whole TV receiver with
an accelerating voltage exceeding 20 Kv:
- On the outer of the apparatus:
the licence number …/…/…/Rö, and the
following text:
Die in diesem Gerät entstehende
Röntgenstrahlung ist ausreichend
abgeschirmt.
Beschleunigungsspannung: max: … Kv.
- Supplied with the apparatus:
a copy of “Zulassungsschein”, together with
the notices required there.
c) In case of TV receivers with accelerating
voltages not exceeding 20 Kv:
Die in diesem Gerät entstehende
Röntgenstrahlung ist ausreichend abgeschirmt.
Beschleunigungsspannung: max: … Kv.
Justification:
German ministerial decree against ionizing
radiation (Röntgenverordnung), dated 1987-0108.
NOTE The German nimisterial decree
(Röntgenverordnung) is under revision.
Annex ZC
Delete the A-deviation for Clause 5 for Germany
and add the following new A-deviation:
Clause National deviation Germany
6.1 The following requirement applies:
For the operation of any cathode ray tube intended
for the display of visual images
operating at an acceleration voltage exceeding 40
kV, authorization is required, or
application of type approval (Bauartzulassung) and
N/A
Korea Testing Certification
Page 27 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Germany – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2007-05-29 in CB Bulletin)
Clause
Requirement + Test
marking.
Justification:
German ministerial decree against ionizing
radiation (Röntgenverordnung), in force since
2002-07-01, implementing the European Directive
96/29/EURATOM.
NOTE Contact address:
Physikalisch-Technische Bundesanstalt,
Bundesallee 100, D-38116 Braunschweig,
Tel.: Int+49-531-592-6320, Internet:
http://www.ptb.de
Result - Remark
Verdict
Korea Testing Certification
Page 28 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Japan – National Differences to IEC 60065:2001+A1:2005+A2:2010
(Test results according to last modification date 2012-04-12 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
Verdict
1.1.3
Addition:
Add the following as a NOTE after the first
sentence.
NOTE 1 In Japan, the requirements for regions
with moderate apply.
N/A
2.4.9
Replacement:
In NOTE 1, replace “see 4.2.2 of IEC 62151” by
“see 4.2.2 of IEC 62151 [27]”.
N/A
2.6.2A
Addition:
Add this sub clause.
CLASS 0I EQUIPMENT: Equipment which has, as
for protection against electric shock,
- at least using BASIC INSULATION, and
- providing a means of connecting to the
protective earthing conductor in the building
wiring those conductive parts that are
otherwise capable of assuming HAZARDOUS
VOLTAGES if the BASIC INSULATION fails,
and
- using a supply cord without earthing conductor
or a plug without earthing pin.
Apparatus provided with a cord set having a twopin type plug with a lead wire for earthing or having
three pin - tow pin adaptor is also regarded as
Class 0I.
NOTE Class 0I equipment may have a part
constructed with Double Insulation or Reinforced
Insulation.
N/A
3.2
Addition:
Add the “Class 0I equipment” in the first sentence of
this sub-clause.
N/A
3.2
Addition:
Add the following after the first sentence of this subclause.
NOTE Equipment often transported and used
should not be Class I equipment nor Class 0I
equipment.
N/A
4.2.8
Deletion:
Delete this clause.
N/A
4.3.4, b)
Replacement:
Replace IEC 60730-1 by JIS C 9730-1
(corresponding to IEC 60730-1).
N/A
4.3.12
Deletion:
Delete this clause.
N/A
4.3.13
Replacement:
N/A
Korea Testing Certification
Page 29 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Japan – National Differences to IEC 60065:2001+A1:2005+A2:2010
(Test results according to last modification date 2012-04-12 in CB Bulletin)
Clause
Requirement + Test
Replace “250 V a.c.” by “the maximum of the
variable range”.
5.4.2A
Addition:
For CLASS 0I EQUIPMENT, the following
instruction shall be indicated where readily visible
on the mains plug or the product:
“WARNING: Provide an earthing connection”
Example in Japanese:
Result - Remark
Verdict
N/A
Moreover, for CLASS 0I EQUIPMENT, the
following instruction shall be indicated where
readily visible on the product or written in the
operating instructions:
“WARNING: Provide an earthing connection
before the mains plug is connected to the mains.
And, when disconnecting the earthing connection,
be sure to disconnect after pulling out the mains
plug from the mains.”
Example in Japanese:
6.2
Replacement:
N/A
In NOTE 1, replace IEC 61040 [10] by JIS C
6181:1995 [10].
7.1.5
Addition:
Add the words, “without dimensions restrictions”
after the figure, “65 K” in the first sentence of
Condition “b” in Table 3 as follows.
For parts not likely to be touched during intended
use, temperature rises up to 65 K without
dimensions restrictions are allowed under normal
operating conditions.
N/A
Addition:
nd
Add the following paragraph as 2 paragraph of
Condition “d “in Table 3.
For materials which are not listed in Table 3,
temperature rises in the normal operating
conditions are considered satisfactory if these
materials comply with item 3 of detailed
regulations, 1.(1),b, Appendix 4 in the Ministerial
Ordinance on stipulating technical requirements for
the Electrical Appliance and Material. Permissible
N/A
Korea Testing Certification
Page 30 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Japan – National Differences to IEC 60065:2001+A1:2005+A2:2010
(Test results according to last modification date 2012-04-12 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
temperature rise of “Supply cords and wiring
insulation” is applicable only to the materials used
in supply cords complying with JIS C 3662
(corresponding to IEC 60227) or JIS C 3663
(corresponding to IEC 60245). Materials used in
other wiring shall comply with item 3 of detailed
regulations, 1.(1).b, Appendix 4 in the Ministerial
Ordinance on stipulating technical requirements for
the Electrical Appliance and Material.
Addition:
Verdict
N/A
In the first paragraph of Condition “f” of Table 3,
add ”JIS K 7206:1999 or” before the reference, ISO
306.
Addition:
N/A
In Condition “f,” 1) of Table 3, add ”JIS K
7206:1999 or” before the reference, ISO 306.
7.2
Addition:
In NOTE 2, add ”or JIS standard (identical to or
modified IEC)” after the word, IEC standard.
N/A
8.5
Addition:
N/A
In the first paragraph, add “and Class 0I
Equipment” after the words, Class I Equipment.
8.5
Addition:
In the six paragraph (before NOTE 3), add the
following to the end of the first sentence.
N/A
CLASS 0I EQUIPMENT shall be provided with a
protective earthing terminal at any point outside the
apparatus where easily visible or a protective
external earth wire from mains plug.
8.11
Addition:
N/A
In NOTE 2, c), add “or JIS C 2107, JIS C 2336, JIS
C 2338” after the reference, IEC 60454.
9.1.1.1
Addition:
In the last paragraph, add the following sentence
after the first sentence.
For CLASS 0I EQUIPMENT, the r.m.s. TOUCHCURRENT to earth shall not be more than 1.0 mA.
N/A
10
Replacement:
N/A
In NOTE, replace “IEC 60664-1 and IEC 60664-4
[9]” by “JIS C 0664:2003 and IEC/TR3 60664-4 [8]”
10.1
Addition:
Add “CLASS 0I EQUIPMENT and” to the head of
the first paragraph.
N/A
10.3.2
Addition:
N/A
In Table 5, add the following values to the sub-table
of NOTE.
Korea Testing Certification
Page 31 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Japan – National Differences to IEC 60065:2001+A1:2005+A2:2010
(Test results according to last modification date 2012-04-12 in CB Bulletin)
Clause
11.2.1
Requirement + Test
Result - Remark
Verdict
Test voltage (peak)
Operating
Voltage U
(peak)
Curve A
Curve B
142 V
1 414 V
2 828 V
Addition:
N/A
Add the following after the original NOTE.
NOTE 2 Fuses except for the ones according to
IEC 60127 shall be tested in consideration of the
characteristic.
11.2.3
Addition:
Add “and CLASS 0I” after the words, CLASS I.
N/A
13.4
Replacement:
In NOTE 2 of Table 11, replace “IEC 60664-1” by
“JIS C 0664:2003” (corresponding to IEC 60664-1).
N/A
14.3.3.2
Addition:
N/A
In the second sentence of the first paragraph, add
“or JIS C 2107, JIS C 2336 and JIS C 2338” after
the reference, IEC 60454.
14.5.1.1
Addition:
N/A
In item a), add “JIS C 9730 series or” before the
reference, IEC 60730 series.
14.5.1.2
Replacement:
N/A
In the first sentence of item a), replace “IEC 60691”
by “IEC 60691, JIS C 6691:2003 or Appendix 3 of
the Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance and
Material”.
Replacement:
N/A
After the second sentence of item a), replace “IEC
60691” by “JIS C 6691:2003 or IEC 60691”.
14.5.2.1
Replacement:
Replace the first and the second sentence as
follows:
Fuse-links, DIRECTLY CONNECTED TO THE
MAINS, used in order to prevent the apparatus
from becoming unsafe within the sense of this
standard shall comply with
- the relevant part of IEC 60127 or JIS C 6575,
unless they have a rated current outside the range
specified in that standard. In the latter case, they
shall comply with the relevant part of IEC 60127 or
JIS C 6575 as far as applicable, or
- Appendix 3 of the Ministerial Ordinance on
stipulating technical requirements for the Electrical
Appliance and Material (limited to Fuses with the
rated current of 1 A or more).
N/A
Korea Testing Certification
Page 32 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Japan – National Differences to IEC 60065:2001+A1:2005+A2:2010
(Test results according to last modification date 2012-04-12 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
Verdict
14.5.2.2
Addition:
Add the following sentence before the last
paragraph.
For fuses according to Appendix 3 of the Ministerial
Ordinance on stipulating technical requirements for
the Electrical Appliance and Material, all that needs
to be marked is the rated current.
N/A
14.5.3
Replacement:
N/A
Replace “IEC 60730-1” by “JIS C 9730-1”
(corresponding to IEC 60730-1).
14.5.4
Replacement:
N/A
Replace IEC 60127 by “IEC 60127 or JIS C 6575”.
14.6.1
Addition:
Add the following paragraph after NOTE.
The following manually operated mechanical
switches shall meet the requirements specified in
item a) or b) below.
- the controlling current exceeds 0.2 A r.m.s a.c. or
d.c.
- the voltage across the open switch contacts
exceeds 35 Vpeak ac or 24 Vdc.
N/A
14.6.1
Replacement:
N/A
In item a), replace “IEC 61058-1” by “IEC 61058-1
or JIS C 4526-1:1999”.
14.6.2
Replacement:
N/A
Replace “IEC 61058-1” by “IEC 61058-1 or JIS C
4526-1:1999”.
14.6.3
Replacement:
N/A
Replace “IEC 61058-1” by “ IEC 61058-1 or JIS C
4526-1:1999”.
14.6.5
Replacement:
N/A
Replace “IEC 61058-1” by “ IEC 61058-1 or JIS C
4526-1:1999”.
14.7
Replacement:
N/A
Replace “IEC 60950” by “JIS C 6950:2006”.
15.1.1
Replacement:
Replace the first and second paragraph by the
following.
Plugs and appliance couplers for the connection of
the apparatus to the MAINS and socket-outlets and
interconnection couplers for providing MAINS
power to other apparatus shall comply with the
relevant JIS standards for plugs, socket-outlets,
appliance couplers or interconnection couplers. If
there is no appropriate JIS standard, they shall
comply with the relevant IEC standards.
N/A
Korea Testing Certification
Page 33 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Japan – National Differences to IEC 60065:2001+A1:2005+A2:2010
(Test results according to last modification date 2012-04-12 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
Appliance connectors, interconnection outlets and
interconnection plug-connectors compiled with
Appendix 3 of the Ministerial Ordinance on
stipulating technical requirements for the Electrical
Appliance and Material are accepted. In that case,
if due to the shape the contact parts are
connectable to those specified in standard sheets
of IEC 60320-1, they shall comply with dimensions
and ratings specified in the relevant standard
sheets of IEC 60320-1.
Examples of relevant specifications and standards:
- Plugs / Socket-outlets: Appendix 4 of Article 1 of
the Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance. Article
2 (corresponding to IEC 60884) of the
Ordinance.
- Appliance couplers: Appendix 4 of Article 1 of the
Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance. Article
2 (corresponding to IEC 60320-1) of the
Ordinance.
- Appliance inlets: IEC 60320-1
- Appliance outlets: Appendix 4 of Article 1 of the
Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance. IEC
60320-2-2.
- Plug connectors: Appendix 4 of Article 1 of the
Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance.
Delete NOTE 1 and NOTE 2.
Verdict
15.1.1
Replacement:
Replace the paragraph after NOTE 2 by the
following.
MAINS socket-outlets and interconnection couplers
mounted on CLASS 0I and CLASS II apparatus
shall not permit connection of CLASS I apparatus.
N/A
15.1.1
Replacement:
Replace the paragraph before NOTE 3 by the
following.
MAINS socket-outlets and interconnection couplers
mounted on CLASS I apparatus shall be provided
with protective earthing contacts which are reliably
connected to the PROTECTIVE EARTHING
TERMINAL or contact of the apparatus. If not, it
shall not permit connection of CLASS I apparatus.
N/A
Replacement:
Replace NOTE 4 by the following.
NOTE 4 Socket-outlets not allowing the connection
of CLASS I apparatus can be designed, for
instance, similar to IEC 60906-1, standard sheets
3-1 or 3-2, or according to IEC 60320-2-2, standard
N/A
Korea Testing Certification
Page 34 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Japan – National Differences to IEC 60065:2001+A1:2005+A2:2010
(Test results according to last modification date 2012-04-12 in CB Bulletin)
Clause
Requirement + Test
sheets D or H.
Result - Remark
Verdict
15.1.2
Deletion:
Delete the following sentence in NOTE.
An example of a connector not meeting the
requirements of this sub clause is the so-called
"banana" plug.
N/A
15.1.3
Replacement:
Replace the references, “IEC 60083 [1], IEC
60320, IEC 60884, IEC 60906” by “JIS C 8282
(corresponding to IEC 60884), JIS C 8303, IEC
60320 and IEC 60906”.
N/A
15.2
Addition:
N/A
Add “and CLASS 0I EQUIPMENT” after the words,
“CLASS I EQUIPMENT”
15.3.1
Addition:
Add the following paragraphs after the first
paragraph.
The external earth wire of plug with an external
earth wire shall not be earthed by a clip.
Rated voltage of plug with an protective external
earth wire shall be less 150 Vac.
N/A
Deletion:
Delete the following paragraph.
In SUPPLY APPARATUS of CLASS I with nonHAZARDOUS LIVE output voltage, output circuits
shall not be connected to the protective earthing
conductor.
N/A
Replacement:
In the first paragraph, replace “IEC 60998-2-2” by
“IEC 60998-2-2 or JIS C 2814-2-2:2001”.
N/A
Replacement:
N/A
In the first paragraph, replace “IEC 60999” by “IEC
60999-1”.
Replacement:
N/A
In the third paragraph, replace “IEC 60335-1” by
“JIS C 9335-1:2003 (corresponding to IEC 603351)”.
15.3.3
Replacement:
N/A
Replace “ISO 261 or ISO 262” by “JIS B 02052:2001 or JIS B 0205-3:2001”.
15.3.5
Replacement:
N/A
In the second paragraph, replace “IEC 60950” by
“JIS C 6950:2006”.
15.3.5
Replacement:
Replace Table 15 by the following.
N/A
Korea Testing Certification
Page 35 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Japan – National Differences to IEC 60065:2001+A1:2005+A2:2010
(Test results according to last modification date 2012-04-12 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
RATED CURRENT
CONSUMPTION of the
apparatus a
Nominal cross-sectional
area
A
mm2
Up to and including 6
Verdict
0.75 to 1
Over 6 up to and including
10
1
to 1.5
Over 10 up to and
including 16
1.5 to 2.5
a
The RATED CURRENT CONSUMPTION includes
currents which can be drawn from socket-outlets
providing MAINS power for other apparatus.
15.3.9
Addition:
Add the following to the last of the first paragraph.
This does not apply to CLASS 0I EQUIPMENT with
a protective earthing terminal separately.
N/A
15.4.1
Replacement:
N/A
In NOTE 1, replace “IEC 60884-1” by “JIS C 8282
(corresponding to IEC 60884-1)”.
Replacement:
N/A
In NOTE 2, replace “IEC 60083 [1]” by “JIS C
8303”.
15.4.2
Replacement:
N/A
In NOTE, replace “IEC 60083 [1]” by “JIS C
8303:1993 [1]”.
15.4.3
Addition:
Add the following NOTE to Table 17.
NOTE If mains plug is parallel blade, a pull force
as given in “Over 10 A up to and including 16 A,
130/250 V” of Table 17 is applied.
N/A
16.1
Addition:
Add the following to the last of first paragraph.
Or mains cords shall be of the sheathed type
complying with Appendix 1 of Article 1 of the
Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance.
Deletion:
Delete NOTE 1.
Replacement:
Replace the second paragraph by the following.
Compliance is checked by testing MAINS supply
flexible cords in accordance with JIS C 3662
(corresponding to IEC60227) or JIS C 3663
(corresponding to IEC 60245), or Appendix 1 of
Article 1 of the Ministerial Ordinance on stipulating
technical requirements for the Electrical Appliance.
N/A
Replacement:
N/A
Korea Testing Certification
Page 36 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Japan – National Differences to IEC 60065:2001+A1:2005+A2:2010
(Test results according to last modification date 2012-04-12 in CB Bulletin)
Clause
Requirement + Test
Result - Remark
Verdict
In this sub-clause, replace “IEC 60227” by “JIS C
3662 (corresponding to IEC 60227)”.
In this sub-clause, replace “IEC 60245” by “JIS C
3663 (corresponding to IEC 60245)”.
16.2
Addition:
Add the following paragraph after the third
paragraph.
An external earth wire of Class 0I equipment shall
be green/yellow, and the length of external earth
wire of plug with an external earth wire shall be
equal or more than 10 cm from the plug.
N/A
Replacement:
Replace the first paragraph by the following.
Power supply cord conductors complied with JIS C
3662 (corresponding to IEC 60227) or JIS C 3663
(corresponding to IEC 60245) shall have a nominal
cross-sectional area not less than those shown in
table 18. If power supply cord conductors comply
with other standards, it shall comply with relevant
wiring requirements.
N/A
Replacement:
N/A
Replace Table 18 by the following.
RATED CURRENT
CONSUMPTION of the
apparatus a
A
up to and including 6
Over 6 up to and including 10
Over 10 up to and including 16
Nominal cross-sectional
area
mm2
0,75
1
1,5
a
The RATED CURRENT CONSUMPTION includes
currents which can be drawn from the socket-outlets
providing MAINS power for other apparatus.
16.3
Replacement:
N/A
In item a), replace “IEC 60885-1” by “JIS C 36611:1998”.
Replacement:
N/A
In item b), replace “IEC 60227-2” by “JIS C 3662-2
(corresponding to IEC 60227-2)”.
16.5
Addition:
N/A
Add “or CLASS 0I EQUIPMENT used a plug with
an external earth wire” after the words, CLASS I
EQUIPMENT.
20.1.2
Replacement:
N/A
In NOTE, replace ISO 1043-1 [19] by JIS K 68991:2000 [19]”
Annex B
Replacement:
N/A
Replace normative by Informative.
Annex G
Replacement:
Replace IEC 60707 by JIS C 0066:2001
N/A
Korea Testing Certification
Page 37 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Japan – National Differences to IEC 60065:2001+A1:2005+A2:2010
(Test results according to last modification date 2012-04-12 in CB Bulletin)
Clause
Requirement + Test
Replace IEC 60695-2-2 by JIS C 60695-2-2:2000.
Replace IEC 60695-11-10 by JIS Z 2391:1999.
Annex N
Addition:
Result - Remark
Verdict
N/A
Add “- protective earthing lead wire, protective
earthing contact of appliance inlet or external
protective earthing terminal in case of Class 0I
apparatus.” after the second dash of N.1.3.
Replacement:
N/A
Replace the first sentence and two dashes of
N.2.2, as follows:
The continuity of the protective earthing conecction
between
- the ACCESSIBLE conductive parts, including
TERMINALS regarded as ACCESSIBLE (see
8.4), which should be connected to the
PROTECTIVE EARTHING TERMINAL, and
- the protective earthing contact of socket-outlets
respectively, if provided to deliver power to other
apparatus
should be checked between
- the protective earthing contact of the MAINS plug
or appliance inlet, or the PROTECTIVE
EARTHING TERMINAL in case of a
PERMANENTLY CONNECTED APPARATUS, for
CLASS I apparatus, and
- the protective earthing lead wire, the protective
earthing contact of appliance inlet, or external
protective earthing terminal, for CLASS 0I
apparatus.
14.6.1
Replacement:
In item a), replace IEC 61058-1 by “IEC 61058-1 or
JIS C 4526-1:2005”.
P
14.6.2
Replacement:
In item a), replace IEC 61058-1 by “IEC 61058-1 or
JIS C 4526-1:2005”.
P
14.6.3
Replacement:
In item a), replace IEC 61058-1 by “IEC 61058-1 or
JIS C 4526-1:2005”.
P
14.6.5
Replacement:
In item a), replace IEC 61058-1 by “IEC 61058-1 or
JIS C 4526-1:2005”.
P
20.1
Replacement:
In Note 3, replace each IEC 60065 and IEC 60707
by “JIS C 6065” and “JIS C 0066:2001 (IEC
60707).
P
Korea – National Differences to IEC 60065:2001+A1:2005+A2:2010
Korea Testing Certification
Page 38 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
(Test results according to last modification) date 2012-05-31 in CB Bulletin
Clause
Requirement + Test
5.101
Result - Remark
Verdict
N/A
Other Marking: Wording
or an
information regulated in IEC Publication 417 giving
high voltage warning to layman shall be marked, if
an apparatus contains a part more than 600 volts.
15.1.1
Plugs for the connection of the apparatus to the
supply mains and socket outlets for providing
mains power to other apparatus shall comply with
the Korean requirement (KSC8300 and 8305)
31.
Radio frequency interference
The apparatus shall comply with the relevant
CISPR requirements (EMC=EMI+EMS)
N/A
P
Korea Testing Certification
Page 39 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Malaysia – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification) date 2007-05-09 in CB Bulletin
Clause
Requirement + Test
-
Energy Commission circular no.1 year 2003
(no.1/2003)
States that a Certificate of Approval is required for
manufacturing, selling,
Advertising, displaying or importing into Malaysia,
electrical/electronic products
Listed in Annex A.
- The supply voltage in Malaysia is 240 Vac, at
50Hz.
- Class 0 and 01 appliances are not allowed
- 13A fused plug-tops shall comply to Malaysian
standard (MS 589:Part1:1997), if applicable.
- 2-pin plug tops shall comply to Malaysian
standard (MS 1578:2003) if applicable
Result - Remark
Verdict
N/A
Korea Testing Certification
Page 40 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Norway – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification) date 2007-05-29 in CB Bulletin
Clause
Requirement + Test
Result - Remark
Verdict
13.3.1
To the second paragraph the following is added:
In Norway, due to the IT power distribution system
used, the a.c. MAINS supply voltage is considered
to be equal
to the line-to-line voltage, and will remain 230 V in
case of a single earth fault.
Justification:
Based on a use in Norway of an IT power
distribution system where the neutral is not
provided.
N/A
15.1.1
Mains socket-outlets mounted on CLASS II
apparatus shall comply with the specifications
given in CEE Publ. 7 as fas as a
Applicable, with the following amendments:
§ 8 Dimensions
a 2,5 A 250 V two-pole socket-outlets for electronic
apparatus shall comply with the enclosed Standard
Sheet I.
N/A
Korea Testing Certification
Page 41 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Sweden – National Differences to IEC 60065:2001+A1:2005+A2:2010
(Test results according to last modification) date 2011-04-19 in CB Bulletin
Clause
Requirement + Test
Annex B
Replace NOTE 1 by
In the CENELEC countries listed in IEC 62151,
special national conditions apply.
Add the following:
All subclauses given below are subclauses of IEC
62151:2000 (ref. Corrigendum 1 and 2 to IEC
62151).
Subclause 4.1.1 (Corrigendum 2):
Add after the first paragraph:
NOTE - In Sweden, CLASS I equipment which is
intended for connection to the building installation
via a non-industrial plug or a non-industrial
appliance coupler, or both and in addition is
intended for connection to other equipment or a
network shall, if safety relies on connection to
protective earth or if surge suppressors are
connected between the network terminals and
ACCESSIBLE parts, have a marking stating that
the equipment must be connected to an earthed
mains socket -outlet.
The marking text shall be as follows:
"Apparaten skall anslutas till jordat uttag”
Subclause 5.3.1 (Corrigendum 1):
Add after the first test specifications paragraph:
NOTE 1 In Finland, Norway and Sweden, there are
additional requirements for the insulation.
Renumber the existing note as note 2.
For additional requirements for the insulation in
Sweden in the NOTE 1 the following text is added
between the first and second paragraph (this text is
identical to the text in EN 60950-1:2001):
If this insulation is solid, including insulation forming
part of a component, it shall at least consist of
either
- two layers of thin sheet material, each of which
shall pass the electric strength test below, or
- one layer having a distance through insulation of
at least 0,4 mm, which shall pass the electric
strength test below.
If this insulation forms part of a semiconductor
component (e.g. an optocoupler), there is no
distance through insulation requirement for the
insulation consisting of an insulating compound
completely filling the casing, so that CLEARANCES
and CREEPAGE DISTANCES do not exist, if the
component passes the electric strength test in the
accordance with the compliance clause below and
in addition:
- passes the test and inspection criteria of 13.6 with
an electric strength test of 10.3 using the test
Result - Remark
Verdict
N/A
Korea Testing Certification
Page 42 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Sweden – National Differences to IEC 60065:2001+A1:2005+A2:2010
(Test results according to last modification) date 2011-04-19 in CB Bulletin
Clause
Requirement + Test
Result - Remark
voltage of 1,5 kV multiplied by 1,6, and
- is subject to routine testing for electric strength
during manufacturing, using a test voltage of 1,5 kV
(for performance of the test see N.2.1).
It is permitted to bridge this insulation with a
capacitor complying with IEC 60384-14:1993,
subclass Y2.
A capacitor classified Y3 according to IEC 6038414:1993, may bridge this insulation under the
following conditions:
- the insulation requirements are satisfied by having
a capacitor classified Y3 as defined by IEC 6038414, which in addition to the Y3 testing, is tested
with an Impulse test of 2.5kV defined in IEC 62151,
subclause 6.2.1;
- the additional testing shall be performed on all the
test specimens as described in IEC 60384-14;
- the Impulse test of 2.5kV is to be performed
before the Endurance Test in IEC 60384-14 in the
sequence of tests as described in IEC 60384-14.
Subclause 5.3.2 (Corrigendum 1):
Add after the fourth dash:
NOTE - In Sweden, exclusions are applicable for
equipment which is intended for connection to the
building installation wiring using screw terminals or
other reliable means, and for equipment which is
intended for connection to the building installation
wiring via an industrial plug and
socket -outlet or an appliance coupler, or both,
complying with IEC 60309 or with a comparable
national standard.
Amendment A2 (2010)
5.3 To the end of the subclause the following is
added:
CLASS I apparatus which is intended for
connection to the building installation wiring
via a plug or an appliance coupler, or both and in
addition is intended for connection
to other apparatus or a network shall, if safety relies
on connection to protective earth
or if surge suppressors are connected between the
network TERMINALS and
ACCESSIBLE parts, have a marking stating that
the apparatus must be connected to an
earthed MAINS socket-outlet.
Verdict
Korea Testing Certification
Page 43 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Sweden – National Differences to IEC 60065:2001+A1:2005+A2:2010
(Test results according to last modification) date 2011-04-19 in CB Bulletin
Clause
Requirement + Test
The marking text in the applicable countries shall
be as follows:
In Finland: "Laite on liitettävä suojakoskettimilla
varustettuun pistorasiaan"
In Norway: “Apparatet må tilkoples jordet
stikkontakt”
In Sweden: “Apparaten skall anslutas till jordat
uttag”
Norway and Sweden
5.4.1 Secretary Note: Modification at the end of
5.4.1 (after the compliance statement)
already part of A11 (This note will be deleted from
the final text)
Result - Remark
Verdict
Korea Testing Certification
Page 44 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
Switzerland – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2009-12-15 in CB Bulletin)
Clause
Requirement + Test
21.
Ordinance on environmentally hazardous
substances SR 814.081, Annex 1.7,
Mercury - Annex 1.7 of SR 814.81 applies for
mercury.
Switches containing mercury such as thermostats,
relays and level controllers are not allowed.
Ordinance on chemical hazardous risk reduction
SR 814.81, Annex 2.15
Batteries
Annex 2.15 of SR 814.81 applies for batteries
containing cadmium and mercury.
Note: Ordinance relating to environmentally
hazardous substances, SR 814.013
of 1986-06-09 is not longer in force and
superseded by SR 814.81 of 2009-02-01
(ChemRRV).
24.
Supply cords of portable electrical appliances
having a rated current
not exceeding 10 A shall be provided with a plug
complying with IEC 60884-1(3.ed.) + am1, SEV
1011 and one of the following dimension sheets:
- SEV 6533-2:2009 Plug type 11, L + N, 250V 10A
- SEV 6534-2:2009 Plug type 12, L + N + PE, 250V
10A
- SEV 6532-2:2009 Plug type 15, 3L + N + PE,
250/400V 10A
Supply cords of portable electrical appliances
having a rated current
not exceeding 16 A shall be provided with a plug
complying with IEC 60884-1(3.ed.) + am1,
SEV 1011 and one of the following dimension
sheets:
- SEV 5933-2:2009 Plug type 21 L + N, 250 V, 16A
- SEV 5934-2:2009 Plug type 23 L + N + PE, 250
V, 16A
- SEV 5932-2:2009 Plug type 25 3L + N + PE,
250/400V 16A
NOTE 16 A plugs are not often used in Swiss
domestic installation system.
See TRF template regulatory requirements
Switzerland on IECEE Website R.R. TRF
templates.
Result - Remark
Verdict
N/A
Korea Testing Certification
Page 45 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
United Kingdom – National Differences to IEC 60065:2001+A1:2005
(Test results according to last modification date 2007-05-29 in CB Bulletin)
Clause
Requirement + Test
15.1.1
Apparatus which is fitted with a flexible cable or
cord and is designed to be connected to a mains
socket conforming to BS 1363 by means of that
flexible cable or cord and plug shall be fitted with
a ”standard plug” in accordance with Statutory
Instrument 1768: 1994: The Plugs and Sockets etc.
(Safety) Regulations 1994, unless exempted by
those Regulations.
NOTE ”Standard plug” is defined in SI 1768:1994
and essentially means an approved plug
conforming to BS 1363 or an approved conversion
plug.
Justification:
SI 1768: 1994
Result - Remark
Verdict
N/A
Korea Testing Certification
Page 46 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
USA – National Differences to IEC 60065:2001+A1:2005
Clause
Requirement + Test
Result - Remark
Verdict
1.1.1
Delete reference to Annex L: Electronic flash
apparatus for photographic purposes and replace
with reference to UL 122.
P
Mains connected apparatus intended for field
installation complies with the National Electrical
Code, ANSI, NFPA 70.
P
1.1.3
Requirements of apparatus intended for outdoor
use comply with applicable clause of Annex A
P
1.1.5
Some equipment covered by these requirements
may also be required to comply with applicable
requirements in other appropriate standards .........:
P
4.2.1
The rated supply voltage for single phase
apparatus is assumed to be 120V or 120/240V
P
4.2.4
a) Minimum audio output is not less than 0.5 W per
channel unless the maximum audio output is less
than 0.5 W per channel
N/A
4.2.4.1
An apparatus with multiple modes of operation,
multiple signal input sources, or both, is operated
according to the manufacturer's instructions to
produce the maximum power input
N/A
4.2.11
Table 2 - External supply sources are assumed to
be capable of delivering 30 A, unless otherwise
specified (UL 60065 no-load voltage and internal
resistance values)
N/A
4.3.4
As an alternative, PTC thermistors may also
comply with UL 1434.
N/A
5
As an alternative, a reagent grade hexane with a
minimum 85% as n-hexane may be used.
N/A
Test for conductive labels secured in place by
adhesive
N/A
5.1
Component power supplies and adapters
complying with UL 1310, UL 1950, or UL 60950 are
considered to fulfill items "a" through "i" of this
clause.
N/A
5.1f
Rated mains frequency marking on apparatus
N/A
5.1g
Rated current or power marking on apparatus
supplied by supply apparatus for general use
P
5.1j
Date of Manufacture marking
P
5.1k
Factory origin identification marking
P
5.1l
Combination of two graphical symbols and
supplementary marking and/or single graphical
symbol marking
P
5.1m
Equipment rack marking for audio/video systems
N/A
5.1n
Class I apparatus having touch current levels
greater than 0.75 MIU and equal to or less than 3.5
MIU must be marked with a high touch current
N/A
Korea Testing Certification
Page 47 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
USA – National Differences to IEC 60065:2001+A1:2005
Clause
Requirement + Test
marking.
Result - Remark
Verdict
5.1o
Marking on apparatus having grille/ventilation areas
of the top surface that are permitted to have higher
temperature rises according to Note b of Table 3
N/A
5.2c
Output terminals are marked with voltage,
frequency and current or power; output terminals
installed or interconnected in the field must be
marked with the class of wiring
N/A
5.2d
Speaker terminals are marked "Class 1 Wiring",
"Class 2 Wiring" or "Class 3 Wiring".
N/A
5.2d
Operation manual explains risks and proper
connecting and insulating techniques when
connecting a speaker
N/A
5.3
An explanation and illustration of safety related
graphical symbols used on the apparatus are
included in the user instructions preceding any
operating instructions
P
5.4
Important safety instructions are packed with each
apparatus
P
5.4.1
Outdoor use marking for apparatus having no
protection against exposure to water
P
5.4.1e
Deleted
P
5.4.1h
Reference to IEC 61695 is replaced by UL 61965
P
5.4.3
When user operation and installation instructions
contains instructions for use by skilled persons, the
instructions are separate in format and preceded by
a precautionary warning statement
P
6.1
Compliance is checked in accordance with the
requirements in the U.S. Code of Federal
Regulations, Title 21, Chapter 1, Subchapter J,
Sections 1010.2, 1010.3, and 1020.10 by
measuring the radiation produced by the apparatus
employing a production chassis
N/A
6.2
References to IEC 60825-1 are deleted
P
Apparatus is classified and labeled according to the
Code of Federal Regulations, Title 21, Chapter 1,
Subchapter J, Sections 1010.2, 1010.3, 1040.10
and 1040.11.
P
6.2.2
Deleted
P
7
Table 3: Delete reference to conditions h and i
under Table item e for lithium batteries
N/A
Table 3: Temperature limits for various classes of
insulation systems according to UL 60065
N/A
Table 3, Note a: Materials rated in accordance with
UL 746B may be used within their rated
temperature
N/A
Table 3, Note b: For grille/ventilation areas in the
N/A
Korea Testing Certification
Page 48 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
USA – National Differences to IEC 60065:2001+A1:2005
Clause
Requirement + Test
top surface directly above internal heatsinks, a
temperature rise up to 65 K is allowed
Result - Remark
Verdict
7.2
Applies to thermoplastic materials only. A material
temperature rating can be accepted in lieu of the
softening temperature.
N/A
The softening test need not be performed on
materials used in UL Listed or Recognized
components
N/A
8.1
Metal parts are corrosion resistant
P
8.9.1
Sleeving, tape, tubing, and wire insulation comply
with UL 224, UL 510, or UL 1441
P
8.10
Component power supplies and their internal
insulation complying with UL 1310, UL 1950 Third
Edition, or UL 60950 are considered to fulfill the
clause
N/A
8.17
As an option, winding wire insulation complies with
the requirements in UL Subject 2353
N/A
8.19.1
An all-pole switch or circuit breaker is not required
to have contact separation of 3 mm
N/A
8.23
Printed wiring boards involved with the risk of
electric shock comply with the requirements in UL
796.
P
9.1.1.1
For Class I constructions the r.m.s. touch current to
earth is not more than 3.5 MIU
N/A
9.1.1.1a
For audio signals of professional and commercial
apparatus, 120 V r.m.s.
N/A
For audio signals other than professional and
commercial apparatus, 71 V r.m.s.
N/A
9.1.1.1b
Touch current carried out in accordance with UL
101 with the measuring instrument described in
Annex D does not exceed 0.5 MIU. Delete Note 2.
N/A
9.1.1.2
UL articulated finger (figure 14) used instead of the
test probe B (IEC 61032)
N/A
Reference to test probes 18 and 19 of IEC 61032
are deleted
N/A
10
Table 5, Note 1: With respect to mains voltages in
the range of 105-130 V (r.m.s.), the test voltages
are considered to be 1414 V peak for basic and
supplementary insulation and 2828 V peak for
reinforced insulation
N/A
11
Component power supplies and their power
transformers complying with UL 1310, UL 1950 3rd
Ed., or UL 60950 are considered to fulfill the clause
N/A
11.1
The permissible touch current for terminal contacts
increased to twice the value given in 9.1.1.1.
P
11.2.1
Additional fuse testing is not required if the
temperature is limited by fuses
N/A
Korea Testing Certification
Page 49 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
USA – National Differences to IEC 60065:2001+A1:2005
Clause
Requirement + Test
Result - Remark
Verdict
N/A
12
Component power supply adaptors and their
enclosures complying with UL 1310, UL 1950 3rd
Ed., or UL 60950 are deemed to fulfill the clause
12.1.3
Impact test uses the 50 mm steel sphere only
P
Table 6 - Impact test criteria detailing impact
location, impact energy and additional pass/fail
results applied according to UL 60065
P
12.1.4
As an alternative, any number from one to three
samples are permitted to be used in any
combination that results in a total of three drops
N/A
12.1.6
Handle strength test. When polymeric materials
are involved, testing is to be conducted before and
after the sub-clause 12.1.5 stress relief test.
N/A
12.8
Test for enclosures, barriers, components and
leads that rely on adhesive
N/A
13
Component power supplies and their power
rd
transformers complying with UL 1310, UL 1950 3
Ed., or UL 60950 are deemed to fulfill the clause
N/A
13.4
The material group is verified according to UL 746A
N/A
Reference to the IEC 60112 PTI test is deleted
13.5.1
Reference to IEC 60249-2 is replaced by UL 796
N/A
N/A
13.5.2
Coated printed wiring boards comply with UL 746C
N/A
14
Annex Y and additional component requirements
applied according to UL 60065
N/A
14.1
Component power supplies and their resistors
complying with UL 1310, UL 1950 Third Edition, or
UL 60950 are considered to fulfill the clause
N/A
14.2
Component power supplies and their capacitors
complying with UL 1310, UL 1950 Third Edition, or
UL 60950 are considered to fulfill the clause.
N/A
14.2.1
As an alternative, a component such as a
capacitor, a combination capacitor and resistor, or
a suppressor may comply with UL 1414.
N/A
14.2.2
As an alternative, a capacitor, a combination
capacitor and resistor, or a varistor, or a
suppressor may comply with UL 1414.
N/A
14.2.4
Components subjected to the requirements in
14.2.1 and 14.2.2 also comply with UL 1414
enclosure requirements
N/A
14.3
Component power supplies and their inductors and
rd
windings complying with UL 1310, UL 1950 3 Ed.,
or UL 60950 are considered to fulfill the clause
N/A
14.4
High voltage materials are rated V-2 minimum
N/A
14.4.1
High voltage arcing test replaces the High voltage
transformers and multipliers test
N/A
14.4.2
Deleted
N/A
Korea Testing Certification
Page 50 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
USA – National Differences to IEC 60065:2001+A1:2005
Clause
Requirement + Test
14.4.3
High voltage component part flame test
14.4.4
High voltage isolating component test
N/A
14.5.1.1
Thermal cut-outs comply with UL 873, UL 8730-2-9
or UL 60730-2-9
N/A
14.5.1.2
Thermal links comply with UL 60691
N/A
14.5.1.3
Deleted
N/A
14.5.2.1
Fuse links comply with UL 248-14
N/A
14.5.2.2
Reference to IEC 60127 is deleted
N/A
Pre-arcing time/current characteristic and breaking
capacity marking requirements are deleted
N/A
14.5.3
As an alternative, a PTC thermistor may comply
with requirements of UL 1434
N/A
14.5.4
Reference to fuse-links is deleted
N/A
Other protective devices directly connected to the
mains have adequate breaking capacity and
comply with UL 873, UL 1416, UL 1417 or UL 2111
N/A
Switches and relays comply with UL 1054, UL
61058-1 or UL 508
N/A
Mains switch or relay are rated for the total rated
current consumption of the apparatus
N/A
Rating of a mains switch or relay in audio
apparatus intended for commercial use
N/A
14.6.2 - .4
Deleted
14.6.5
A switch or relay that controls a mains socket-outlet
have a rating equal to the rated current
consumption of the apparatus plus the current
rating of the socket-outlet
N/A
N/A
14.6.6
Mains switches comply with (a), (b) or (c)
N/A
Mains relay contacts comply with (a), (b) or (d)
N/A
A switch that controls a mains receptacle complies
with (b) and a relay that controls a mains
receptacle complies with (b) or (d)
N/A
14.6.6a
Switch or relay contacts have current rating equal
to or greater than 1.414 times the inrush current of
the apparatus
N/A
14.6.6b
Switch or relay is TV rated
N/A
14.6.6c
Switch is located on the back of apparatus and is
not operable from a remote control
N/A
14.6.6d
Relay subjected to the Relay Endurance Test
N/A
14.6.6.1
Peak inrush current test
N/A
14.6.6.2
Relay endurance test
N/A
14.6.7
Double pole switch controlling a.c. and d.c. circuits
N/A
14.6.1
Result - Remark
Verdict
N/A
Korea Testing Certification
Page 51 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
USA – National Differences to IEC 60065:2001+A1:2005
Clause
Requirement + Test
14.7
The jointed test finger (Fig 14) is used to determine
accessibility and operation of the interlock
14.10.1
Internal rechargeable and non-rechargeable
batteries that are replaceable by the user or skilled
persons additionally comply with 14.10.2 – 14.10.5.
N/A
Test requirements from UL 2054 added for special
battery packs that are removable by the user from
the apparatus (Short circuit, Abnormal charging,
Forced-discharge, and 250-N steady force tests
may be carried separately from the apparatus)
N/A
Note: Consumer grade, non-rechargeable carbonzinc or alkaline batteries are not subjected to the
tests specified in Clauses 14.10.2 – 14.10.5.
N/A
14.10.5
Alternatively, one sample subjected to three drops
N/A
14.10.6
Location of overcurrent protective device ..............:
N/A
Alternatively, the overcurrent protective device in
the apparatus battery-supply circuit is not required
if the apparatus is to be connected to a vehicle
power outlet via UL 2089 vehicle battery adapter
N/A
Component power supplies and their optocouplers
complying with UL 1310, UL 1950 Third Edition, or
UL 60950 are considered to fulfill the clause.
N/A
Optocouplers comply with UL 1577
N/A
Optocouplers bridging reinforced insulation comply
with requirements for double protection as specified
in UL 1577
N/A
External clearances and creepage distances of
optocouplers comply with 13.1
N/A
Reference to IEC 61051-2 replaced by UL 1449
N/A
Reference to IEC 60707 replaced by UL 94
N/A
All references to IEC 60151 are deleted
N/A
Attachment plug current rating (no less than 125%
of the current drawn under normal operating
conditions) and voltage rating ................................ :
N/A
Configuration and electrical rating of an attachment
plug for apparatus for use on more than one supply
voltage by means of a voltage selector .................. :
N/A
Polarized attachment plug
N/A
Wire gauge of conductors and internal wiring
connecting mains socket-outlets
N/A
Means of output connections on an audio amplifier
having an open-circuit audio output voltage not
limited to 120 V that is permanently connected to
the mains
N/A
Quick Connect Terminals:
N/A
a) Male tabs firmly mounted in place;
N/A
14.11
14.12
15.1.1
15.1.3.1
Result - Remark
Verdict
N/A
Korea Testing Certification
Page 52 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
USA – National Differences to IEC 60065:2001+A1:2005
Clause
Requirement + Test
b) Mating female connectors provided with the
apparatus;
Result - Remark
Verdict
N/A
c) Strain Relief Test of Clause 16.5;
N/A
d) Installation instructions provided for assembly of
terminal to a conductor and strain relief
N/A
e) Terminals are appropriate for use with the size
and type of wire specified
N/A
15.1.3.2
Audio amplifiers having an audio output not limited
to 120 V that are connected to the mains by a
flexible cord
N/A
15.2
Cross-sectional area of the earthing conductor in a
supply cord or in an interconnecting cable
N/A
Earthing conductors may have green or
green/yellow insulation
N/A
Reference to IEC 60950 is replaced by Article 310
of the National Electrical Code, ANSI/NFPA 70
N/A
Table 15 - "AWG" replace mm2 values
N/A
15.4
Component power supply adaptors complying with
UL 1310, UL 1950 Third Edition, or UL 60950 fulfill
the clause
N/A
16.1
Reference in the first paragraph to “sheathed”
flexible cords is deleted
N/A
References to IEC 60227 and IEC 60245 deleted
N/A
Ampacity and VW-1 marking of mains supply
flexible cords .......................................................... :
N/A
Table 17A - Cords for apparatus
N/A
Power supply cord earthing conductor size ........... :
N/A
Reference to IEC 60950, Table 3B is replaced by
Article 400 of the National Electrical Code
N/A
Table 18 - Upper current limit in column 1
increased from 16 to 30 A and "AWG" wire sizes
N/A
16.3
c) Flexible cords not complying with 16.1, used as
connection between the apparatus and other
apparatus are marked VW-1
N/A
16.5
When polymeric materials are involved, strain and
twist testing is to be conducted before and after the
sub-clause 12.1.5 stress relief test.
N/A
17.8
Expanded to include all cart/stand parts supplied by
the manufacturer, such as casters and brackets.
Suitable assembly instructions are required.
N/A
Relevant fixing means are not required when
installation is to be done by a skilled person
N/A
17.10
Termination of aluminum conductors used as
internal wiring
N/A
17.11
An accessory was investigated to determine that:
N/A
15.3.5
16.2
Korea Testing Certification
Page 53 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
USA – National Differences to IEC 60065:2001+A1:2005
Clause
Requirement + Test
Result - Remark
a). The accessory, and the combination of the
accessory and the apparatus presents no hazard in
the sense of this standard, and
b). The accessory is provided with installation
instructions.
17.11.1
Installation of an accessory by a skilled person:
a) The mechanical positioning is accomplished by
means of tools normally available or by means of
special tools provided as part of the installation kit,
N/A
b) The electrical connections are made by using
existing terminals and connections in the apparatus
or the building wiring
N/A
Non-intrinsically protected picture tubes comply
with 18.1, 18.2.2 and 18.3. Intrinsically protected
picture tubes with a maximum face dimension
exceeding 7.5 cm comply with UL 61965.
N/A
A bulb of a picture tube having a face diameter of
7.5 cm or more are mounted in an enclosure
N/A
Enclosure opening dimensions
N/A
18.1
All tubes are mounted such that the enclosure of
the apparatus protects the tube against the effects
of implosion.
N/A
18.2
Clauses 18.2, 18.2.1 and 18.2.3 are deleted
N/A
19
The tests in 19.1, 19.2 and 19.3 do not cause the
apparatus to overturn.
N/A
The test in 19.2.1 does not cause the apparatus to
slide
N/A
When polymeric materials are involved, testing is to
be conducted before and after the sub-clause
12.1.5 stress relief test.
N/A
19.1
References to an apparatus in combination with a
supplied cart or recommended stand are deleted
N/A
19.2
References to an apparatus in combination with a
supplied cart or recommended stand are deleted
N/A
19.2.1
Slide test
N/A
19.3
Horizontal force stability test using Table 20A
values from UL 60065
N/A
19.5
Reference to the impact hammer in the first
compliance paragraph is deleted
N/A
19.6
Equipment rack mounting test
N/A
20.1a
Deleted
20.1b
Exception for parts such as protection TV lenses,
loudspeaker parts, external accessories, and
fibrous materials
18
20.1.2
Verdict
P
P
Reference to IEC 60707 replaced by UL 94
P
Sleeving, extruded tubing and insulation on wiring
P
Korea Testing Certification
Page 54 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
USA – National Differences to IEC 60065:2001+A1:2005
Clause
Requirement + Test
are rated VW-1:
a) wiring located in a circuit that is considered a
potential ignition source, or
Result - Remark
Verdict
b) wiring not located in a circuit that is a potential
ignition source but is in contact with wiring located
in a circuit that is a potential ignition source
P
20.1.2
Tape in contact with parts of circuits that are
potential ignition sources is flame retardant
P
20.1.3
Printed wiring boards, on which the available power
as the connection exceeds 15 W or the operating
voltage exceeds 50 V a.c. or d.c under normal
operating conditions, are of flammability category
V-1 or better
P
Reference to IEC 60707 replaced by UL 94
P
Exception for printed boards housed in metal
enclosures is deleted
P
Option to use Clause G.1 of Annex G is deleted
P
Components and parts comply with the relevant
flammability category according to UL 94 as
specified in table 21
P
Component power supplies complying with
UL1310, UL1950 3rd Ed., or UL60950 fulfill the
clause
P
Table 21 - Flammability categories for components
and parts
P
Fire enclosure required:
1) circuits and components where the available
power exceeds 15 W,
2) inductors and windings conductively connected
to the mains, and
3) high-voltage products.
P
The fire enclosure complies with the flammability
requirements of Table 22 per UL 94 and 746C
P
Reference to IEC 60707 or clause G.1 of annex G
replaced by UL 94 or UL 746C
P
Table 22 - Flammability categories for fire
enclosures
P
20.1.4
20.2.1
Internal fire enclosures openings and material
requirements
N/A
Compliance is checked by inspection and
measurement and using the articulated finger
probe, figure 18.
N/A
20.2.3
Outer enclosures have a minimum flammability
rating of HB when an internal fire enclosure is
provided
N/A
A
Apparatus intended for outdoor use or for wet
locations
N/A
20.2.2
Korea Testing Certification
Page 55 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
USA – National Differences to IEC 60065:2001+A1:2005
Clause
Requirement + Test
a) provided with a means to be transportable
Result - Remark
Verdict
N/A
b) has a mass less than 35 kg
N/A
c) can be battery operated, or
N/A
d) associated literature states or implies such use
N/A
An apparatus as described in a), b), or c) above
that is marked as specified in 5.4.1 a) is not
intended for outdoor use or wet location use
N/A
Apparatus permanently installed outdoors is
considered to be for permanent outdoor use
N/A
A.5
Clauses A.5, A.5.1 and A.5.4.1 are deleted
A.9.1.1
Touch current test after the water spray test
described in A.11.1.1
N/A
N/A
A.10
Clauses A.10, A.10.2 and A.10.2.1-2 are deleted
N/A
A.11.1.1
Apparatus subjected to the water spray test
specified in UL 1598
N/A
A.16.1
Flexible cords are suitable for outdoor use
N/A
A.20.2.1
Enclosures for an apparatus intended for
permanent outdoor location comply with
requirements for Type 3 enclosures in UL 50
N/A
B
IEC 62151 Clause 4 applies except for 4.1.2, 4.1.3,
4.2.1.1 and 4.2.1.2
N/A
The requirements of 4.2.1.1 are replaced by the
requirements or 2.3.1 of UL 60950, Third Edition
N/A
Voltages on the TNV-0 circuits, TNV-1 circuits and
accessible conductive parts in the event of a single
insulation fault
N/A
Apparatus intended to be connected to
telecommunication networks and having ringing
voltages applied to the apparatus is subjected to
touch current limits in accordance with clause
5.1.8.1.1 of UL 60950
N/A
Telecommunication network that uses outside
cable complies with the requirements for protection
against overvoltage from power line crosses per
6.4 of UL 60950
N/A
UL 60950 Acoustic tests for apparatus containing
an earphone held against the ear
N/A
Apparatus provided with appropriate markings and
instructions as described in Annex NAA of UL
60950
N/A
Reference to IEC 60990 replaced by UL 101
N/A
D
Add touch current value in MIU where
MIU = U2 x 2 (r.m.s. value)
P
G
Annex G deleted
N/A
L
Annex L deleted
N/A
Korea Testing Certification
Page 56 of 56
Report No.: W14-65-007
Attachment 2 - National Differences
USA – National Differences to IEC 60065:2001+A1:2005
Clause
Requirement + Test
Result - Remark
Verdict
N/A
Q
Safety requirements for video apparatus for use in
health care facilities
R
Safety requirements for undercabinet apparatus
N/A
S
Safety requirements for in-wall mounted apparatus
N/A
T
Safety requirements for apparatus with projection
lamps
N/A
U
Safety requirements for permanently connected
apparatus
N/A
V
Safety requirements for carts, stands, and similar
apparatus for use with specific apparatus covered
by this standard
N/A
W
Construction details for a 0.02-ohm shunt for use in
the peak inrush-current measurement
N/A
X
Manufacturing and production-line tests and
verification
P
Y
Standards for components
P
Korea Testing Certification
Page 1 of 4
APPENDIX No.1
Photograph (Front view 1)
APPENDIX No.1
Photograph (Front view 2)
Report No.: W14-65-007
Korea Testing Certification
Page 2 of 4
APPENDIX No.1
APPENDIX No.1
Photograph (rear side view)
Photograph (rear side view )
Report No.: W14-65-007
Korea Testing Certification
Page 3 of 4
APPENDIX No.1
Photograph (inside view 1)
APPENDIX No.1
Photograph (inside view 2)
Report No.: W14-65-007
Korea Testing Certification
Page 4 of 4
APPENDIX No.1
APPENDIX No.1
Photograph (inside view 3)
Photograph (inside view 4)
Report No.: W14-65-007
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement