CV-105
DVI & Audio to HDMI Converter
User
Manual
Made in Taiwan
Safety
and
Notice
The CV-105 DVI & Audio to HDMI Converter has been tested for conformity to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the CV-105 should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit. z Follow all instructions and warnings marked on this unit. z Do not attempt to service this unit yourself, except where explained in this manual. z Provide proper ventilation and air circulation and do not use near water. z Keep objects that might damage the device and assure that the placement of this unit is on a stable surface. z Use only the power adapter and power cords and connection cables designed for this unit. z Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
Warning!
This
device
is
served
purely
for
conversion
between
video
formats.
This
device
CANNOT
convert
the
input/output
video
resolutions.
~ 1 ~
Introduction
The CV-105 DVI & Audio to HDMI Converter provides an easy and instant approach for converting digital video (DVI-D) and both digital audio (S/PDIF) and analog stereo audio to digital HDMI. With this module, DVI based devices such as PC with S/PDIF or analog stereo audio can readily connect to your HDMI TV at lowest cost.
DVI PC
DVI cable
Audio cable
CV ‐ 105
HDMI cable
HDMI display/projector
HDTV
Features
z DVI video up to 165MHz z RCA S/PDIF audio input z Stereo analog audio input z Front panel LED indicators z Easy installation
~ 2 ~
Specifications
&
Package
Contents
Model Name
Technical
Role of usage
HDMI compliance
DVI compliance
Video Bandwidth
Video support
Audio support
Input TMDS signal
CV-105
Digital-to-analog format converter
HDMI
DVI 1.1
Single-link 165MHz [4.95Gbps]
720p, WUXGA [1920x1200@60] & UXGA [1600x1200@60]
Stereo audio
1.2 Volts [peak-to-peak]
Input DDC signal
ESD protection
5 Volts [peak-to-peak, TTL]
[1] Human body model — ±19kV [air-gap discharge] & ±12kV [contact discharge]
[2] Core chipset — ±2kV
Transmission
Input
UXGA V 65m [210ft]
1x DVI
1x 3.5mm analog audio
RCA connector Sockets for Analog audio and video
Output 1x
RCA connector 75W female
3.5mm connector Earphone socket for analog stereo audio
Mechanical enclosure
Dimensions
[L x W x H]
Weight
Model
Package
126 x 94 x 27mm [5"x3.7"x1.0"]
270 x 175 x 80mm [10.6"x6.9"x3.1"]
Carton
Model 357g
Package
450 x 370 x 300mm [1'6"x1'3"x11.8"] oz]
800g [1.8 lbs]
Fixedness
Power supply
Power consumption
Operation temperature
Storage temperature
Relative humidity
Package Contents
Wall-mounting case with screws
0~40
5V 2A DC
3.5 Watts [max]
°
-20~60
C [32~104
°
°
C [-4~140 °
F]
F]
20~90% RH [no condensation]
1x CV-105
1x DC 5V 2A wall wart
1x User Manual
~ 3 ~
Front
Panel
Panel Descriptions
SPDIF In
Audio In
DVI In
SPDIF In: 2-channel digital S/PDIF audio input.
Audio In: 2-channel analog audio input thru the 3.5mm earphone jack.
DVI In: Connect to a DVI source with a DVI M-M cable here.
Rear
Panel
HDMI Out Power
HDMI Out: Connect to a HDMI display with a HDMI M-M cable here.
+5V DC
Green light: Status indicator.
Rotary Control: 0 = Analog audio mode; 1 = S/PDIF audio mode; 2-5 = Reserved; 6 = Use default EDID; 7= Learn
EDID from HDMI display.
Power: Power indicator. Red light on means power on.
+5V DC: Connect to 5V DC power supply.
EDID Learning
1.
Power up the CV-105. Connect HDMI display to HDMI Out.
2.
Turn the rotary control counterclockwise from 0 to 7.
3.
The green light will be bright and then dark to indicate the EDID is learned.
4.
Turn the rotary control clockwise from 7 to 0. DO NOT let the rotary control arrow pass 6, which will erase the just learned EDID and reset to default EDID.
~ 4 ~
CONNECTION DIAGRAM
~ 5 ~
Hardware Installation
1.
Connect DVI video source to the video input with a DVI cable.
2.
Connect S/PDIF or stereo audio source to RCA jack or 3.5mm earphone jack respectively.
3.
Connect HDMI display to the HDMI output connector with a HDMI cable
4.
Power up the CV-105.
Notice
1.
Only HDMI enabled TV sets with underscan/overscan
*
support, the full active video can be accurately displayed. Some HDMI equipped TV sets may not support this feature. If underscan/overscan
*
is NOT supported, the top, bottom, left and right border of the active video may be screened, and the S/PDIF audio may not sound right.
2.
Analog stereo audio can merely support 2-channel audio. This version does NOT support 8-channel analog audio applications.
3.
S/PDIF audio input can support 2 out of 8-channel audio input.
4.
S/PDIF supports only 48kHz audio sample rate. Other than this rate, the input digital audio should be adjusted to 48kHz in order to get audio signal correctly sent.
* The underscan mode displays the full video frame, which reveals content on the edge that is recorded.
In overscan, the field monitor zooms in to the area that would be visible on most televisions.
Set the field monitor to underscan if your video will be viewed on a computer monitor or shown with a projector and also to look for light stands, microphones, and other unwanted objects on the edges of your shot.
Set it to overscan to see how the video will look on a television.
~ 6 ~
Limited Warranty
The SELLER warrants the CV-105 DVI & Audio to HDMI Converter to be free from defects in the material and workmanship for 1 year from the date of purchase from the SELLER or an authorized dealer. Should this product fail to be in good working order within 1 year warranty period, The SELLER, at its option, repair or replace the unit, provided that the unit has not been subjected to accident, disaster, abuse or any unauthorized modifications including static discharge and power surge. This warranty is offered by the SELLER for its BUYER with direct transaction only. This warranty is void if the warranty seal on the metal housing is broken.
Unit that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair. Such repairs are warranted for 90 days from the day of reshipment to the
BUYER. If the unit is delivered by mail, customers agree to insure the unit or assume the risk of loss or damage in transit. Under no circumstances will a unit be accepted without a return authorization number.
The warranty is in lieu of all other warranties expressed or implied, including without limitations, any other implied warranty or fitness or merchantability for any particular purpose, all of which are expressly disclaimed.
Proof of sale may be required in order to claim warranty. Customers outside Taiwan are responsible for shipping charges to and from the SELLER. Cables are limited to a 30 day warranty and cable must be free from any markings, scratches, and neatly coiled.
The content of this manual has been carefully checked and is believed to be accurate. However, The SELLER assumes no responsibility for any inaccuracies that may be contained in this manual. The SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. Also, the technical information contained herein regarding the CV-105 features and specifications is subject to change without further notice.
~ 7 ~
