LCD KEYBOARD LCD KLAVIATŪRA

LCD KEYBOARD LCD KLAVIATŪRA
LCD KEYBOARD
LCD KLAVIATŪRA
EKB2
User Manual v1.1
Compatible with:
• ESIM264 v7.09.02 and up.
• ESIM364
Main features:
• Alarm system arming & disarming;
• Stay mode activation & deactivation;
• System parameter configuration;
• PGM output control;
• System information display on LCD screen;
• Audio indication by built-in mini buzzer;
• Wireless device information display;
• Keyboard partition switch.
EKB2 is an LCD keyboard intended for using with ELDES alarm systems. The system configuration is performed by accessing EKB2
menu and entering the required values. ELDES alarm system allows to connect up to 4 EKB2 keyboards.
NOTE: For complete system configuration & control using EKB2 keyboard, please refer to ELDES alarm system installation
manual located at www.eldes.lt/en/download
1. Package Content
1. EKB2..........................................................................qty. 1
2. User manual...........................................................qty. 1
3. 5,6kΩ resistor.........................................................qty. 1
4. Jumper.....................................................................qty. 2
5. Screws......................................................................qty. 4
2. Technical Specifications
2.1 Electrical & Mechanical Characteristics
Power Supply
12-14V
Maximum Keyboard Connection Cable Length
100 m.
Dimensions
133 x 89 x 19 mm
Range of Operating Temperatures
0...+55ºC
One menu level back / cancel
Menu navigation – up
Menu navigation – down
Confirm (enter) value
...
Value typing
Keyboard partition switch / minus symbol for entering negative temp. value
Additional menu / minus symbol for
entering negative temp. value
2
150mA max.
Temperature
Digital Clock
GSM Signal
Strength
System Status
Message
System
Trouble
Indication
20,2 C
0
STAY
BYP
TBL
ready
GARAGE
00:45
Main Screen
View
Bypass Mode
Indication
Stay Mode
Indication
Custom
Keyboard
Partition
Title
Fig. No. 1
2.2 Keys Functionality
2.3 Connector and Main Unit Functionality
Vin
Positive 12-14V power supply terminal
COM
Negative 12-14V power supply terminal
G
RS485 interface for communication (green wire)
Y
RS485 interface for communication (yellow wire)
COM
Common terminal for Z1
Z1
Security zone terminal
A0
Keyboard address pin
A1
Keyboard address pin
Buzzer
Mini buzzer providing sound signals
Tamper
Tamper-button for EKB2 enclosure status
monitoring
VIN
COM
Z1
G
Y
COM
A0 A1
Buzzer
Tamper
Fig. No. 2
2.4 Keyboard Address
A0 and A1 pins located on the back side of the keyboard are intended to set keyboard address. The keyboard address is set by
putting the jumper (-s) on the pins. ELDES alarm system allows to connect up to 4 EKB2 keyboards - each set under different address. Jumper combinations for different keyboard address configuration are indicated in the table below.
Address Configuration
Jumper position
Address
A0 A1
Keyboard 1
A0 A1
Keyboard 2
A0 A1
Keyboard 3
A0 A1
Keyboard 4
The address of each connected keyboard is also indicated in ELDES Configuration Tool software.
USER MANUAL EKB2 V1.1
3
3. Installation
1.
Remove the screw located on the bottom side of the enclosure (see
Fig. No. 3)
2.
Detach keyboard holder from EKB2 keyboard by gently pulling theholder towards yourself (see Fig. No. 4).
3.
Fix the keyboard holder on the wall using the screws. (see Fig. No. 5)
4.
Disconnect ELDES alarm system main power supply and backup
battery.
5.
Wire up keyboard terminals to ELDES alarm system respectively – Vin
to AUX+, COM to AUX-, Y to Y, G to G (see Fig. No. 6).
6.
Z1 and COM terminals must be connected with resistor of 5,6kΩ nominal (see Fig. No. 6). As keyboard zone Z1 is disabled by default, it can
be enabled by SMS, keyboard and ELDES Configuration Tool. Keyboard
zone Z1 must be enabled and resistor connected even if the tamper
button alone is required.
7.
Set the keyboard address by putting the jumper on A0 and A1 pins
(see chapter 2.4 Keyboard Address).
8.
Fix the keyboard into the holder.
Fig. No. 3
ATTENTION! Before fixing the keyboard into the holder please , make
sure that the tamper button is properly pressed (see Fig. No. 2).
9.
Screw up the bottom side of the enclosure. (see Fig. No. 3)
10.
Power up ELDES alarm system.
11.
EKB2 keyboard is ready.
Fig. No. 4
4. EKB2 Zone & Tamper
Keyboard EKB2 has one wired zone Z1 and one tamper button. By default,
the keyboard zone Z1 is disabled. The keyboard zone can be enabled by
SMS, keyboard and ELDES Configuration Tool. When Z1 is enabled, it operates
like any other system zone, therefore a sensor can be connected to it. In
addition, Z1 and COM terminals must be connected with resistor of 5,6kΩ
nominal.
The tamper button is intended for monitoring the enclosure status of EKB2,
therefore the system causes alarm if the enclosure is illegally opened. Keyboard zone Z1 must be enabled and resistor connected even if the tamper
button alone is required.
Fig. No. 5
ELDES alarm panel
Y G
VIN
COM
Z1
AUX- AUX+
EKB2
5,6kΩ
Fig. No. 6
4
G
Y
COM
5. Additional Information
Limited Liability
The buyer must agree that the system will reduce the risk of fire, theft, burglary or other dangers but does not guarantee against
such events. “ELDES UAB” will not take any responsibility regarding personal or property or revenue loss while using the system.
“ELDES UAB” liability according to local laws does not exceed value of the purchased system. “ELDES UAB” is not affiliated with
any of the cellular providers therefore is not responsible for the quality of cellular service.
Manufacturer Warranty
The system carries a 24-month warranty by the manufacturer “ELDES UAB”. Warranty period starts from the day the system has
been purchased by the end user. The warranty is valid only if the system has been used as intended, following all guidelines
listed in the manual and within specified operating conditions. Receipt must be kept as a proof of purchase date. The warranty is
voided if the system has been exposed to mechanical impact, chemicals, high humidity, fluids, corrosive and hazardous environment or other force majeure factors.
Safety instructions
Please read and follow these safety guidelines in order to maintain safety of operators and people around:
• DO NOT use the system where it can be interfere with other devices and cause any potential danger.
• DO NOT use the system with medical devices.
• DO NOT use the system in hazardous environment.
• DO NOT expose the system to high humidity, chemical environment or mechanical impacts.
• DO NOT attempt to personally repair the system.
Keyboard EKB2 is a device mounted in limited access areas. Any system repairs must be done only by qualified, safety aware
personnel.
The system must be powered by 12-14V
and be easily accessible.
150mA max power supply and must be approved by LST EN 60950-1 standard
Main power must be disconnected before any installation or tuning work starts. The system installation or maintenance must
not be done during stormy conditions.
The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates that
the product must not be disposed of together with household waste. To prevent possible harm to human health and/or the
environment, the product must be disposed on in an approved and environmentally safe recycling process. For further infor­
mation on how to dispose of this product correctly, contact the system supplier, or the local authority responsible for waste
disposal in your area.
Copyright © “ELDES UAB”, 2012. All rights reserved
It is not allowed to copy and distribute information in this document or pass to a third party without advanced written authorization by “ELDES
UAB”. “ELSDES UAB” reserves the right to update or modify this document and/or related products without a warning. Hereby, “ELDES UAB” declares
that this LCD keyboard EKB2 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration
of conformity may be consulted at www.eldes.lt
USER MANUAL EKB2 V1.1
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement