User manual
G-WIN Intel® Series
Rugged Panel PC
Intel® Celeron N2930 1.83GHz (Bay Trail) series
Intel® Atom Dual Core D2550 1.86GHz
w/ NM10 Series
Intel® Atom N270 1.06GHz
w/ 945GSE Series
User Guide Version 1.5
WinMate Communication INC.
FCC Statement
This device complies with part 15 FCC rules. Operation is
subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and founded comply with the limits for "a"
digital device class, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment uses
and can radiate radio frequency energy, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct
the interference at him own expense. CAUTION: Changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
G-WIN Intel Rugged Series Panel PC User Guide
II
Copyright Notice
Copyright © 2008 Winmate Technology Inc., ALL RIGHTS RESERVED.
No part of this document may be reproduced, copied, translated, or transmitted
in any form or by any means, electronic or mechanical, for any purpose,
without the prior written permission of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of
their respective owners.
Disclaimer
We reserves the right to make any product changes without notice,
including circuits and/or software described or contained in this manual in
order to improve design and/or performance. Winmate Communication
assumes no responsibility or liability for the use of the described product(s),
conveys no license or title under any patent, copyright, or masks work rights
to these products, and makes no representations or warranties that these
products are free from patent, copyright, or mask work right infringement,
unless otherwise specified. Applications that are described in this manual are
for illustration purposes only. Winmate Communication Inc. makes no
representation or warranty that such application will be suitable for the
specified use without further testing or modification.
Warranty
We warrant that each of its products will be free from material and
workmanship defects for a period of one year from the invoice date. If the
customer discovers a defect, Winmate will, at its option, repair or replace the
defective product at no charge to the customer, provided it is returned during
the warranty period of one year, with transportation charges prepaid. The
returned product must be properly packaged in it’s original packaging to obtain
warranty service.
If the serial number and the product shipping data differ by over 30 days,
the in-warranty service will be made according to the shipping date. In the
serial numbers the third and fourth two digits give the year of manufacture, and
the fifth digit means the month (e. g., with A for October, B for November and C
for December).
For example, the serial number 1W08Axxxxxxxx means October of year
2008.
G-WIN Intel Rugged Series Panel PC User Guide
III
Check List
Before using this Panel PC, please make sure that all the items listed
below are present in your package
 1 x G-WIN Intel Series Panel PC
 1 x G-WIN Intel Series Rugged Panel PC User Guide
 1 x IA30/IA32/ID32/IB32 SBC User Manual (Depends on Model #)
 1 x Power adapter、Power cord(Optional)
 1 x Power wire ( w/ terminal block)
 1 x CD-ROM disc with Driver Utility and User’s Manual
 1 x Touch Driver CD (Optional)
 1 x WLAN Antenna (Optional)

Mounting Bracket & kits (Optional)
Make sure that all of the items listed above are present. Do not attempt to
apply power to the system if there is damage to any of its components.
Customer Service
We provide service guide for any problem as follow steps:First, visit the
website at http://www.winmate.com to find the update information about the
product. Second, contact with your distributor, sales representative, or our
customer service center for technical support if you need additional assistance.
You may have the following information ready before you call:
 Product serial number




Peripheral attachments
Software (OS, version, application software, etc.)
Description of complete problem
The exact wording of any error messages
In addition, free technical support is available from our engineers every
business day. We are always ready to give advice on application requirements
or specific information on the installation and operation of any of our products.
Please do not hesitate to call or e-mail us.
Notice
1. Do not touch the LCD panel surface with sharp or hard objects.
2. Do not use abrasive cleaners, waxes or solvents for cleaning, use only a dry
or damp, soft cloth.
3. Use only with a high quality, safety-approved, AC/DC power adapter.
G-WIN Intel Rugged Series Panel PC User Guide
IV
Safety Precautions

Warning!
Always completely disconnect the power cord from
your chassis whenever you work with the hardware. Do not
make connections while the power is on. Sensitive
electronic components can be damaged by sudden power
surges. Only experienced electronics personnel should
open the PC chassis.

Caution!
Always ground yourself to remove any static charge
before touching the CPU card. Modern electronic devices
are very sensitive to static electric charges. As a safety
precaution, use a grounding wrist strap at all times. Place all
electronic components in a static-dissipative surface or
static-shielded bag when they are not in the chassis.
G-WIN Intel Rugged Series Panel PC User Guide
V
Safety and Warranty
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Please read these safety instructions carefully.
Please keep this user’s manual for later reference.
Please disconnect this equipment from any AC outlet before cleaning. Do
not use liquid or spray detergents for cleaning. Use a damp cloth.
For pluggable equipment, the power outlet must be installed near the
equipment and must be easily accessible.
Keep this equipment away from humidity.
Put this equipment on a reliable surface during installation. Dropping it or
letting it fall could cause damage.
The openings on the enclosure are for air convection. Protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
Make sure the voltage of the power source is correct before connecting
the equipment to the power outlet.
Position the power cord so that people cannot step on it. Do not place
anything over the power cord.
All cautions and warnings on the equipment should be noted.
If the equipment is not used for a long time, disconnect it from the power
source to avoid damage by transient over-voltage.
Never pour any liquid into an opening. This could cause fire or electrical
shock.
Never open the equipment. For safety reasons, only qualified service
personnel should open the equipment.
14. If any of the following situations arises, get the equipment checked by
service personnel:
A. The power cord or plug is damaged.
B. Liquid has penetrated into the equipment.
C. The equipment has been exposed to moisture.
D. The equipment does not work well, or you cannot get it to work
according to the user’s manual.
E. The equipment has been dropped and damaged.
F. The equipment has obvious signs of breakage.
15. Do not leave this equipment in an uncontrolled environment where the
storage temperature is below -20°C (-4°F) or above 60°C (140°F). It may
damage the equipment.
G-WIN Intel Rugged Series Panel PC User Guide
VI
Revision History
Version
Date
1.0
2008.07.31
1.1
2009.04.14
1.2
2011.05.09
1.3
2011.08.11
1.4
1.5
Note
Author

First Version
Sarah Su

Second Version add IA30
series
Sarah Su

Add IA32 series
Henry Hsu

Add I931 series、terminal
block instruction
Henry Hsu
2013.06.25

Add ID32 series
Marc Tsai
2014.11.19

Add IB32 series
Jimmy Chen
G-WIN Intel Rugged Series Panel PC User Guide
VII
Contents
CHAPTER 1 GENERAL INFORMATION ........................................................ 1
1-1 Introduction .................................................................................................... 1
1-2 G-WIN RUGGED Series Panel PC System Mother-Board Specifications . 2
1-2-1 Intel IA30 SBC Specifications(945 GSE Based) .................. 2
1-2-2 Intel IA32 SBC Specifications(945 GSE Based) .................. 3
1-2-3 Intel ID32 SBC Specifications(NM10 Based) ....................... 4
1-2-4 Intel IB32 SBC Specifications(Intel Atom SoC Based) ......... 5
1-3 Panel PC Selection Guide ............................................................................. 5
CHAPTER 2 GETTING STARTED..................................................................... 7
2-2 Input / Output Devices ................................................................................... 7
2-1 Starting the Panel PC& O/S Installation ....................................................... 8
2-3 Driver Installation ......................................................................................... 10
CHAPTER 3 TOUCH DRIVER INSTALLATION ...........................................11
3-1 Introduction .................................................................................................. 11
3-2 The ELO AccuTouch/ CarrollTouch infrared Driver Installation .............. 12
3-2-1 Configuration Utility ................................................................ 13
3-3 The Premier Touch Driver Installation ....................................................... 15
3-3-1 Install Touch-Kit ...................................................................... 15
3-3-2 Configuration Utility ................................................................ 16
CHAPTER 4 G-WIN RUGGED PANEL PC MOUNTING GUIDE ............... 18
4-1 Vehicle Mounting.......................................................................................... 19
4-2 VESA Mounting ............................................................................................ 21
KNOWN ISSUES ................................................................................................. 22
NOTICES .............................................................................................................. 23
♀♂
Chapter 1 GENERAL INFORMATION
1-1 Introduction
G-WIN Intel® Rugged Panel PCs with fanless, low power but high
performance platform design, sunlight readable panel, WLAN integration,
great ability for anti-shock & vibration, IP65 protection and anti-corrosion
coating with aluminum alloy housing. Both of great mobility and robust
design are fitting the demands for every harsh environment applications
such as logistics, transportation/ fleet management, heavy vehicles,
utility and also outdoor usage.
G-WIN Intel Rugged Series Panel PC User Guide
1
♀♂
1-2 G-WIN RUGGED Series Panel PC System Mother-Board
Specifications
1-2-1 Intel IA30 SBC Specifications(945 GSE Based)
3.5”
Form Factor
CPU
Intel® Atom N270 1.6GHz Processor
Chipset
Intel® 945GSE / ICH7M Chipset
Memory
1 x SODIMM socket, support up to 2GB DDR2 400/533
BIOS
Award 4Mbit Flash
VGA Controller
Integrated in Intel 945GSE, LVDS/CRT
VGA Memory
Shared memory, max. 224MB
LCD Support
Intel® GMA950 graphic engine built-in, single- or dual-channel panel
support up to 1600 x 1200, 18bibit
Ethernet
2 x GigaLAN (Dual Realtek RTL811B Controller )
Audio
Realtek ALC655 5.1 channel (Line-out, Line-in & Mic. in)
IDE
One channels; supports Ultra DMA 33/66/100
Serial
1 x RS-232, 1 x RS-232/422/485 (optional)
USB
4 x USB (2 x Rear I/O, 2 x pin-header)
KB / Mouse
Mini-DIN PS/2 interface
Connector
Expansion Slots
1 x Mini PCI
Power Adapter
9~36V (Default) or DC IN 12V (Optional)
Storage
(Default)
8.4” PPC
4G Compact Flash Card
10.4” PPC
2.5” 160G HDD
2.5” Flash Disk(SSD)
(Optional)
Industrial Compact Flash Card
Compact Flash Card
Industrial Compact Flash Card
O/S(Optional)
Windows XP Embedded/ Windows XP Professional Embedded/
WinCE5.0 / Linux 2.6.11/Win7 Embedded
G-WIN Intel Rugged Series Panel PC User Guide
2
♀♂
1-2-2 Intel IA32 SBC Specifications(945 GSE Based)
Form Factor
3.5”
CPU
Intel® Atom N270 1.6GHz Processor
Chipset
Intel® 945GSE / ICH7M Chipset
Memory
1 x SODIMM socket, support up to 2GB DDR2 400/533
BIOS
Award 4Mbit Flash
VGA Controller
Integrated in Intel 945GSE, LVDS/CRT
VGA Memory
Shared memory, max. 224MB
LCD Support
Intel® GMA950 graphic engine built-in, single- or dual-channel panel
support up to 1600 x 1200, 18bibit
Ethernet
2 x GigaLAN (Dual Realtek RTL811B Controller )
Audio
Realtek AC97
USB
4 x USB (2 x Rear I/O, 2 x pin-header)
Serial
3 x RS-232(pin-header), 1 x RS-232/422/485 (Rear I/O)
Expansion Slots
1 x Mini PCI
Power Adapter
9~36V (Default) or DC IN 12V (Optional)
8.4” PPC
Storage
(Default)
10.4”/15” PPC
4G Compact Flash Card
2.5” 500G HDD
2.5” Flash Disk(SSD)
(Optional)
Industrial Compact Flash Card
Compact Flash Card
Industrial Compact Flash Card
O/S(Optional)
Windows7
Embedded/
Windows
XP
Embedded/
Windows
XP
Professional Embedded/ Linux 2.6.11
G-WIN Intel Rugged Series Panel PC User Guide
3
♀♂
1-2-3 Intel ID32 SBC Specifications(NM10 Based)
3.5”
Form Factor
CPU
Intel® Atom Dual Core D2550 1.86GHz Processor
Chipset
Intel® NM10 Chipset
Memory
1 x SODIMM socket, support up to 4GB DDR3 800/1066
BIOS
AMI 16Mbit Flash
LCD Support
LVDS: Single-channel 24 bit LVDS Up to 1440 x 900 @ 60Hz
VGA Mode : Up to 1920 x 1200 @ 60Hz
DVI : 1920 x 1200 @ 60Hz
Ethernet
2 x GigaLAN (Dual Broadcom BCM57780 GbE controller)
Audio
Realtek ALC886 HD Audio Codec
USB
6 x USB (2 x Rear I/O, 4 x pin-header)
Serial
3 x RS-232(pin-header), 1 x RS-232/422/485 (Rear I/O)
Expansion Slots
1 x Mini PCIe slot (for wireless module)
1 x Mini PCIe slot (for SATA SSD)
Power Adapter
9~36V (Default) or DC IN 12V (Optional)
8.4” PPC
Storage
(Default)
10.4”/12.1”/15” PPC
mSATA 32G SSD
mSATA 32G SSD
2.5” 32/64/128G SSD
(Optional)
Industrial Compact Flash Card
2.5” 500G HDD
Industrial Compact Flash Card
O/S(Optional)
Windows7
Embedded/
Windows
XP
Embedded/
Windows
XP
Professional Embedded/ Linux 3.2
G-WIN Intel Rugged Series Panel PC User Guide
4
♀♂
1-2-4 Intel IB32 SBC Specifications(Intel Atom SoC Based)
3.5”
Form Factor
CPU
Intel® Celeron N2930 1.83GHz Processor
Chipset
Intel® Atom SoC integrated
Memory
1 x SODIMM socket, support up to 8GB DDR3 1066
BIOS
AMI 16Mbit Flash
LCD Support
LVDS: Dual-channel 24 bit LVDS Up to 1920 x 1080 @ 60Hz
VGA Mode : Up to 1600 x 1200 @ 60Hz
DVI : 1920 x 1080 @ 60Hz
Ethernet
2 x GigaLAN (Intel WG82574L GbE controller)
Audio
Realtek ALC886 HD Audio Codec
USB
1 x USB3.0, 5 x USB2.0(4 x pin-header)
Serial
3 x RS-232(pin-header), 1 x RS-232/422/485 (Rear I/O)
Expansion Slots
1 x Mini PCIe slot (for wireless module)
1 x Mini PCIe slot (for SATA SSD)
Power Adapter
9~36V (Default) or DC IN 12V (Optional)
8.4” PPC
Storage
(Default)
10.4”/12.1”/15” PPC
mSATA 32G SSD
mSATA 32G SSD
2.5” 32/64/128G SSD
(Optional)
Industrial Compact Flash Card
2.5” 5000G HDD
Industrial Compact Flash Card
O/S(Optional)
Windows Embedded Standard 7/ Windows Embedded 8 Standard/
Windows Embedded 8.1 Industry Pro/ Linux 3.2
1-3 Panel PC Selection Guide
The G-WIN series Rugged Panel PCs support 8.4-inch and 10.4-inch TFT
Panel, please refer as the below:
LCD Spec.
M/B / Model Name
IA30 /IA32 SBCIntel® 945 GSE
Resolution
(Recommended)
Display Color
R08IA3S-VMT1
800 × 600
262,144 (6bit/colors)
R08IA3S-VMM2
1024 × 768
262,144 (6bit/colors)
R10IA3S–VMP1
800 × 600
262,144 (6bit/colors)
R15IA3S-VMA3HB
1024 × 768
16.2M (8bit/colors)
R15IA3S–VMA2
1024 × 768
16.7M (8bit/colors)
G-WIN Intel Rugged Series Panel PC User Guide
5
♀♂
ID32 SBCIntel® NM10
IB32 SBCIntel® Celeron
N2930
R08ID3S-VMT1
800 × 600
16.2M (8bit/colors)
R10ID3S-VMT2
1024 × 768
16.2M (8bit/colors)
R10ID3S-VMA2
640 × 480
16.2M (8bit/colors)
R10ID3S-VMP1
800 × 600
16.2M (8bit/colors)
W12ID3S-VMM9
1280 × 800
16.2M (8bit/colors)
R15ID3S-VMA3HB
1024 × 768
16.2M (8bit/colors)
R08IB3S-VMT1
800 × 600
16.2M (8bit/colors)
R10IB3S-VMT2
1024 × 768
16.2M (8bit/colors)
R10IB3S-VMA2
640 × 480
16.2M (8bit/colors)
R10IB3S-VMP1
800 × 600
16.2M (8bit/colors)
W12IB3S-VMM9
1280 × 800
16.2M (8bit/colors)
R15IB3S-VMA3HB
1024 × 768
16.2M (8bit/colors)
G-WIN Intel Rugged Series Panel PC User Guide
6
♀♂
Chapter 2 Getting Started
2-2 Input / Output Devices
The following figure shows the I/O arrangement of the ID32 series G-WIN
Rugged Panel PC. The backside of the chassis contains most of the connectors.
8.4”
10.4”
12.1”
15”
G-WIN Intel Rugged Series Panel PC User Guide
7
♀♂
1
DC Terminal
Block ( Default)
Pluggable 3pin terminal block power input
2
COM
9-pin male Serial Port connector that can attach a serial
mouse or other serial devices directly to the port.
3
VGA
Use VGA port to connect an external Display.
4
USB
USB-compatible devices can be plugged directly into
the USB 2.0 port.
LAN
10/100/1000 Mbps, connect a network cable to the
standard RJ-45 port and get connection to the Local
Area Network (LAN).
5
2-1 Starting the Panel PC& O/S Installation
1) Connect the cable as picture below.
2) Screw the Terminal block to fix the cable
G-WIN Intel Rugged Series Panel PC User Guide
8
♀♂
3) Connect the cable as picture below.
Connect to female terminal block
Connect to Power supply
unit to get 0V
Connect to Power supply
unit to get +9~36V DC
4.
Press the power on switch to start the Panel PC.
5.
Press “DEL” to enter the CMOS setting and check the BIOS setup.
6.
You may install your own O/S if it is not installed.
When installing O/S for this Panel PC, please follow the steps and use
external equipment as Keyboard and Mouse.
(a) Please use external USB DVD-ROM to run the O/S and Driver setting
(as picture showed below).
USB Cable
G-WIN Intel Rugged Series Panel PC User Guide
9
♀♂
2-3 Driver Installation
The PPC comes with a User’s Manual and Driver CD that contains most of the
drivers and utilities of your needs.
1. Following the step by step to install Driver (Please refer I330/I530 SBC
User’s Manual Chapter 3, 4, 5, 6, 7) include: Graphic, Chipset, VGA, Audio,
SATA and Ethernet.
2. Following the step by step to install the Touch screen if necessary (Please
refer G-WIN RUGGED series PPC User Guide Chapter 3).
G-WIN Intel Rugged Series Panel PC User Guide
10
♀♂
Chapter 3 Touch Driver Installation
3-1 Introduction
The PPC supports three kinds of Touch Panel Solutions: ELO AccuTouch
touch-screen, ELO Infrared touch-screen and Premier Touch system. All of the
touch-screen consists of a touch-screen and an electronic touch-screen
controller.
The G-WIN Rugged Series Panel PC touch device is used RS232 interface
touch controller card via the COM2 port
Note
inside Panel PC. When the touch
driver installed either for ELO or Premier Touch systems, it will detect COM2
port automatically.
The ELO AccuTouch and Premier touch-screen are based on patented
resistive technology. The touch-screen may be a flat, spherical, or cylindrical. It
is installed over the face of the display. Since its shape matches of the display
face, the touch-screen has excellent clarity and minimal parallax.
The ELO CarrollTouch infrared (IR) technology uses a small frame around
the display with LEDs and photoreceptors on opposite sides, hidden behind an
IR-transparent bezel. The Controller sequentially pulses the LEDs to create a
grid of IR beams. A touch obstructs one or more the beams which identify the X
and Y coordinates. CarrollTouch technology combines superior optical
performance with excellent gasket-sealing capabilities, so it's an excellent
choice for harsh industrial and outdoor kiosk applications. Touched with a finger,
gloved hand, fingernail, or stylus, it delivers a fast, accurate response every
time.
Note: Touch interface recommend:
Com port
1*RS232
Touch interface
Touch Interface Optional
2*RS232
1) RS232(Default-Via Com2) 1) USB
2) USB
G-WIN Intel Rugged Series Panel PC User Guide
11
♀♂
3-2
The
ELO
AccuTouch/
CarrollTouch
infrared
Driver
Installation
ELO AccuTouch/ CarrollTouch infrared driver software provides a
consistent software interface among all ELO AccuTouch/ CarrollTouch infrared
touch screens and controllers.
Go to http://www.elotouch.com/Support/dnld.asp for a complete list of available
drivers.
For Driver Installation, please install the “ELO Touch System Touch Tools
CD” for Windows XP Professional Embedded, Windows 2000, Windows Me,
Windows 98, Windows 95, Windows NT, Windows CE 2.x, 3.0, 4.x, Windows XP
Embedded, Windows 3.1, DOS, OS/2 Warp, and Apple Macintosh. Just follow
the step by step to install the driver.
Select “Auto-detect ELO devices” in the first step. If not, the following step
will need users choose COM2 port for detecting the devices.
G-WIN Intel Rugged Series Panel PC User Guide
12
♀♂
3-2-1 Configuration Utility
After finishing the installation, please follow the steps to test the
configuration utility.
Step.1
Enter “My Computer”, click the “ELO Touch Screen” shortcut function.
Step.2
Click “Align” function key to go to next step.
G-WIN Intel Rugged Series Panel PC User Guide
13
♀♂
Step.3
Correct 4 point locations on screen with the Panel PC. Screen display
as follows.
Step.4
Touch the “yes” function if the cursor follows your finger and finish the
utility test.
G-WIN Intel Rugged Series Panel PC User Guide
14
♀♂
3-3 The Premier Touch Driver Installation
Touch-Kit is the Premier Touch software, which contains drivers of the touch
panel controllers for the specified communication connectors, RS232, PS/2 and
USB, and the other two utilities.
The two utilities are as follows:

Touch Tray support
This is utility for emulating the right and left button of mouse through
controlling touch panel. Users can toggle between right/left mouse
buttons by this utility.

Configuration support
The calibration and draw test of touch panel are done by this utility.
Besides, users can add or remove for new RS-232 or PS/2 touch panel
devices.
3-3-1 Install Touch-Kit
Follow below steps to install Touch-Kit:
Step.1
Put the Touch-Kit CD to CD-ROM.
Step.2
Open the Rugged PPC User Manual CD to “Touch _PM” directory.
Step.3
Double click the Setup.exe, then windows starts to run the installation
program. Notice that does not plug the USB controller on the system
before the installation has been finished.
Step.4
Click Next to continue installation. And it will auto-detect touch devices
in COM2 port at your Panel PC.
Step.5
Following the step by step to finish the driver installation.
G-WIN Intel Rugged Series Panel PC User Guide
15
♀♂
3-3-2 Configuration Utility
After finishing the installation, please follow the steps to test the
configuration utility.
Step.1
Click the “Touch-Kit” shortcut function in the desktop.
Step.2
Enter “General” function and choose the language you need. Then
Enter “Tool” function alignments to match the display. And go to next
step.
G-WIN Intel Rugged Series Panel PC User Guide
16
♀♂
Step.3
Correct 4 point locations on screen with the Panel. Screen display as
following.
Step.4
Play “Yes” to continue if 4 points calibration test is fine and finish the
testing.
G-WIN Intel Rugged Series Panel PC User Guide
17
♀♂
Chapter 4 G-WIN Rugged Panel PC Mounting Guide
The Panel PC is suitable for most of the industrial/commercial application
by any kind of mounting approaches. There are two main mounting approaches
as Vehicle mounting and VESA mounting; both approaches are very easy for
user to set up the Panel PC. As the pictures guided:
Application 1
VEHICLE MOUNTING
Mount with Vehicle mount kits and then mounted into
mounting bracket.
Application 2
WALL MOUNTING
Mount with VESA mount kits and then mounted into wall
G-WIN Intel Rugged Series Panel PC User Guide
18
♀♂
4-1 Vehicle Mounting
Before setting up rugged bracket, please check the complete items with
nothing missing as following.
Rugged Panel PC bracket accessory list
 One Bracket Stand
 Three M5x10 screws with washer
 One “Locking handle” adjustment tool with metal washer
SOP for Bracket Stand Assembly
1. Put the Rugged Panel PC or LCD on the bracket stand, aim to the screw
hole for each other.
G-WIN Intel Rugged Series Panel PC User Guide
19
♀♂
2. Screw on three normal M5x10 screws to fix the rugged product upon the
stand.
3. Screw on Locking handle to screw the rugged product tight.
4. Loose the hand-screw adjustment tool, then you can adjust product angle on
the stand. Then screw the product tight again to fix.
Adjust the product angle
Loose Locking handle
Lock Locking handle
G-WIN Intel Rugged Series Panel PC User Guide
20
♀♂
4-2 VESA Mounting
Fix the Panel PC with four screws (standard VESA), and fasten on the wall
with other four screws.

75 mm x 75 mm
Touch
VESA mount Holes
3mm~6mm
VESA
mount holes
Panel
75 mm
G-WIN Intel Rugged Series Panel PC User Guide
21
♀♂
KNOWN ISSUES
1. When use an “external display” as CRT or LCD for external mode (Panel &
CRT), the resolution of external display may be recommended equal to the
CMOS setting for panel [Flat Panel Type]. If the external display is lower
resolution than CMOS setting in Windows, it may cause display indistinct.

Recommendation in CMOS setting:
i.
Choose “CRT” only when use external display.
ii.
Choose “Panel” only when use internal panel display.
2. If customers need to use USB-HDD or USB-CDROM for booting an
operating system at start-up time, and we recommend to disable the “Quick
Power On Self Test” function in CMOS setting
G-WIN Intel Rugged Series Panel PC User Guide
22
♀♂
NOTICES
1. When you use CF card as storage of Operation System, you need to use
“Fixed Disk Mode” type Compact Flash Card instead of removable disk
mode.
2. The internal Compact Flash socket is NOT A PLUG & PLAY DEVICE;
you may remove the CF card only at POWER-OFF status.
G-WIN Intel Rugged Series Panel PC User Guide
23
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement