Allen-Bradley 140G EXT3 Series Installation
Advertisement
Advertisement
Bul. 140G/140MG
DIR 1000719R0804 Version 01 - 140G-_-EXT3, 140G-_-EXT4
Extended front terminals for 140G-G, 140G-H, 140G-I, 140G-J
Terminali anteriori prolungati
Vorderseitige verlängerte Anschlüsse
Prises avant prolongées
Terminales frontales prolongados
Installation - Installazione - Instalación
Instalação - -
WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
(Seguire i requisiti NFPA70E).
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen
Sie die Anforderungen nach NFPA70E).
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs. (Vous devez respecter la norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de contaminantes. (Cumpra as exigências da norma NFPA70E).
警告:感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
確認してください。( NFPA70E の要件に従ってください)
警告:为了防止触电,在安装或维修之前必须先切断电源。安装在合适的设备
物
Terminal
Terminal
Phase separator
Insulator
Terminal cover
Screw
LENGTH dia.
6.5 mm (0.26") 2.9
DIR 1000719R0804 Version 01
140G-G
1
CLACK
140G-H
1
CLACK
140G-G
3p 4p x3 x4
140G-H 140G-I 140G-J
3p 4p 3p 4p 3p 4p
/ / / / / /
/ / x3 x4 x3 x4 x3 x4 x2 x3 x2 x3 x2 x3 x2 x3
/ / x1 x1 / / x1 x1
/
/
/
/ x1 x1 / / x1 x1
x1 x1 / / x1 x1
140G-I
140G-J
1 2
3
1
3
1
2
2
1
- If present
- Se presente
- Falls vorhanden
- Si présent
- Si lo hay
140G-H, 140G-I
140G-J
4
3
2
CH 5
140G-H 53 lb-in/6 Nm
140G-I 71 lb-in/8 Nm
140G-J 71 lb-in/8 Nm
CH 6
4
5
- If escutcheon mounted, insulation 0.04"/1 mm thickness is required. Supplied by
Costumer.
- Se la mostrina è montata, è richiesta una piastra isolante di spessore 0.04"/1
* mm. A cura del cliente.
- Si la garniture est montée, est requis une plaque d’isolement épaisseur 0.04"/1 mm. À la charge du Client.
- Wenn ein Abdeckrahmen angebracht, Trennplatte Stärke 0.04"/1 mm erforderlich. Vom Kunden beizustellen.
- Si lo marco se monta, se requiere una plata de aislamiento espesor 0.04"/1 mm.
A cargo del Cliente.
WITH ESCUTCHEON
WITHOUT ESCUTCHEON
3p
4p
G
4.56"/116 mm
5.55"/141 mm
3p/4p 5.55"/141 mm
4p 4.56"/116 mm
3p 5.55"/141 mm
(2)
DIR 1000719R0804 Version 01
*
*
X
2
53 lb-in
6 Nm
CH 5
4
OK
140G-G
NO
(3p) 140G-G-PB3L
(4p) 140G-G-PB4L
140G-G, 140G-I
1
1
2
2
- If present
- Se presente
- Falls vorhanden
- Si présent
- Si lo hay
Y
140G-G
G
2.28"/58 mm
Y
X
6
(3p) 140G-H-PB3L
(4p) 140G-H-PB4L
140G-H, 140G-J
7
140G-H, 140G-J 3p ONLY
140G-H
3p
140G-J
3p
A 9.37"/238 mm 11.06"/281 mm
B 2.36"/60 mm 2.65"/67.5 mm
C 2.36"/60 mm 2.65"/67.5 mm
4
4
C B dia. 0.10"/ø 2.6 mm
Y
1
1
Ue<440 V
2
- If present
- Se presente
- Falls vorhanden
- Si présent
- Si lo hay
1
2
3
Ue>440
140G-H, 140G-J 3p
4
5
140G-H, 140G-J 3p
Ue>440
LENGTH dia.
6.5 mm (0.26") 2.9
4
9.7 lb-in
1.1 Nm
140G-H-TL3H
140G-J-TL3H
5
6
6
X X
Y
DIR 1000719R0804 Version 01
(3)
8 dia. 0.10"/ø 2.6 mm
C B
Y
X X
Y
B
C
140G-H
4p
140G-J
4p
A 9.37"/238 mm 11.06"/281 mm
2.36"/60 mm
3.54"/90 mm
2.65"/67.5 mm
4.03"/102.5 mm
4
4
Ue>440
140G-H, 140G-J 4p
1
2
3
140G-H, 140G-J 4p
Ue>440
LENGTH dia.
6.5 mm (0.26") 2.9
4
9.7 lb-in
1.1 Nm
140G-H-TL4H
140G-J-TL4H
5
4 6
6
5
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/ sustainability-ethics/product-environmental-compliance.page
Publication 140G-IN090B-MU-P - September 2015 DIR 1000719R0804 Version 01 (L8804) - B0301
Copyright © 2015 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.

Public link updated
The public link to your chat has been updated.
Advertisement