Graco 311068B Kit, Bead Dispenser LineLazer IV 3900, 5900, 200HS Airless Line Stripers Owner's Manual

Add to My manuals
8 Pages

advertisement

Graco 311068B Kit, Bead Dispenser LineLazer IV 3900, 5900, 200HS Airless Line Stripers Owner's Manual | Manualzz

Installation

Parts

Kit, Bead Dispenser

LineLazer

IV 3900, 5900, 200HS

Airless Line Stripers

311068B

– For application of line striping materials –

3300 psi (228 bar, 22.8 MPa) Maximum Working Pressure

Important Safety Instructions

Read all warnings and instructions in this manual. Save these instructions.

Line Lazer lV 3900,

5900, 200HS

Glass bead system with one 6–in. (152 mm) dispenser

Glass bead system with two 6–in. (152 mm) dispensers

6–in. (152 mm) dispenser and hose

12–in. (305 mm) dispenser and 2 hoses

Model

277065

277064

277067

245516

Series

A

A

A

A ti6587a

GRACO INC.ąP.O. BOX 1441ąMINNEAPOLIS, MNą55440-1441

Copyright 2005, Graco Inc. is registered to I.S. EN ISO 9001

Beads Dispenser Kit

4,15

14

7

11

3

1

11,13

9,10

12

A

11

C

4

3

2

B

Fig. 1

Setup

D

8

Note: Glass bead system and paint guns can be mounted on either side of Linestriper.

1. Relieve pressure; refer to your sprayer manual.

2. Fig. 1. Bolt bead hopper frame legs (1, 3) to

Linestriper with four flange head cap screws (9) and lock nuts (10).

2 311068 ti6588a

3. Place bead hopper ring (14) into holes in bead hopper legs.

4. Bolt bead hopper and bead hopper ring together with washers (15) and lock nuts (4) from kit bag.

5. Install bead hopper (7) on gun-side on top of beads hopper frame.

6. Remove collar from mounting block of dispenser

(8). Locate dispenser on gun support and reconnect collar to attach dispenser to support.

Setup (continued)

7. Move bead dispenser to desired location on rod.

Loosen screw (4) and position link (3) to connect to gun trigger actuator (C). Tighten screw (4) and attach dispenser connecting rod (B) to gun trigger with bridge pin (2).

8. Position spray gun and bead dispenser assembly

(D) to position to be used in bead application and tighten

9. Attach bead hose(s) (12) a.

6 in.: Attach bead hose (12) to bead hopper outlet with hose clamp (11). Plug other bead hopper outlet with cap (13) and clamp (11).

b.

12 in.: Attach two bead hoses (12) to bead hopper outlets with hose clamps (11).

10. Route bead hose down to bead dispenser inlet.

CAUTION

To avoid bead stoppage in hose during use, make sure bead hose is in an arc curved downward with no kinks or high spots.

11. Mark on bead hose where it will connect to bead dispenser inlet.

12. Cut bead hose on mark and attach to bead dispenser inlet using clamp (11). Hoses must be cut as short as possible to allow good bead flow.

Fig. 2 ti6589a

311068 3

Bead Dispenser Kit

Dispenser Adjustments

Only use dry clean beads. Any moisture or contamination with beads will cause poor bead flow. A window type screen can be used to remove unwanted debris before filling glass bead hopper.

Fig. 3. Adjust dispenser plates up or down for desired bead flow. Typical flow rates range between 6 – 8 lb of glass bead per gallon paint.

Fig. 4. Bead dispensers (A) are located behind paint guns. If not adjusted properly, they may miss a short area at end of each paint stripe. Adjust gun cables so guns trigger at midpoint of handle-bar trigger. Adjust bead dispensers (A) so beads flow immediately when trigger is pulled. This ensures independent control to keep beads flowing after paint is turned off.

Operation

Operate the Linestriper as in normal striper operation.

Refer to LineLazer repair manual for paint spray tip recommendations.

CAUTION

To avoid beads stoppage, do not use wet beads or beads that have absorbed moisture. If beads stoppage is occurring, replace with dry beads.

CAUTION

Do not get beads in paint. Beads contaminating the paint supply can damage the pump. Make sure that the paint supply is covered during beads filling and handling.

Requires 2 guns and one 12 in. bead dispenser.

(See Fig. 4 for 8 – 10 in. stripe gun orientation.)

Fig. 3

6 inch stripe

(15 cm)

4 inch stripe

(10 cm)

4” 4”

4–12 inch stripe

(10–30 cm)

4”

4 311068

B A

Beads Dispenser Kit

Gun orientation for 8 – 12 in. stripe operation

ti6591a

For 8 – 10 in. stripe, adjust line width, loosen set screws at (A) and loosen gun adjuster (B). Tilt guns in for desired line width and tighten. Keep bead dispensers together and parallel to the ground.

Fig. 4

CAUTION

To avoid glass beads clumping, don’t store beads in hopper when not in use. Make sure to run beads out of system when done.

8 – 10 in. stripe ti6591a

311068 5

11

13

1

Bead Dispenser Kit – Parts List

14 ti6592a

6

7

2

9

10

11

12

13

14

15

7

8

5

6

3

4

1

2

Ref

No.

Part No.

277065

15F581

115087

15F582

101714

194666

194668

241437

277067

245516

111194

101566

101818

194682

403237

287680

100731

Description

KIT, bead system

. LEG, hopper, RH (painted)

. PLUG, tubing

. LEG, hopper, LH (painted)

NUT, lock

. LABEL, ident

. LABEL, warning

. HOPPER, beads

. DISPENSER ASSY KIT

(includes 8, 11 & 12)

. 6–Inch Dispenser Assy

(Parts List, page 7)

. 12–inch Dispenser Assy

(Parts List, page 8)

. SCREW, cap, flng hd

. NUT, lock

. CLAMP, hose

. HOSE, beads

. CAP

RING, hopper, frame

WASHER

Qty

Ref

2

2

1

2

1

2

2

1

1

1

1

2

3

1

4

4

12

11

1

15 4

3

8

9

5

9

9

10

1

Remove cap (13) and install second hose (12) and clamp (11) for 12–inch bead dispenser

6 311068

1

6-Inch Dispenser Assy – Parts List

4

14

15

20

21

12

19

13

2

3

23

5

12

9

17

18

16

19

20

6 12

10

11

8 ti6593a

7

Ref

No.

Part No.

Description Qty

7

8

9

5

6

3

4

1

2

277067 DISPENSER ASSY KIT, beads (See

item )

198379

114814

15A264

198058

. ROD, connecting

. PIN, bridge

. LINK, mounting, adjustable

1

1

1

. SCREW, cap, schd, 10–24 x 3/8 1

10

15F363

117155

15F357

15F366

117576

198376

. HOUSING, dispenser, 6 in.

. SPRING, compression

. DOOR, dispenser, 6 in.

. PAD, foam, 6 in.

1

2

1

1

. SCREW, machine, hex wash hd 8

. CAP, end, bead dispenser 2

Ref

No.

Part No.

17

18

19

20

21

11

12

13

14

15

16

102598

115483

116998

101885

245679

198380

100085

100086

117275

15F367

166362

Description

. SCREW, cap, sch

. NUT, lock

. FITTING, hose, barb

. SCREW, cap, sch

. BLOCK, mounting

. PLATE, slide

. SCREW, thumb

. WASHER

. STUD, button, snap

. PLATE, slide

. LABEL, Ident tiO770c

Qty

4

4

3

2

1

2

2

1

2

5

1

311068 7

12-Inch Dispenser Assy – Parts List

4 14

19

5

15

1

12

2

3

13

6

12

8

16

17

18

12

10

19

9

7 11

6

7

4

5

8

2

3

1

Ref

No.

Part No.

245516

198379

114814

15A264

198058

245799

117155

198378

116680

Description Qty

DISPENSER ASSY KIT, beads

(See item 8, Beads Dispenser

Kit Parts List)

. ROD, connecting

. PIN, bridge

. LINK, mounting, adjustable

. SCREW, cap, socket head

. HOUSING KIT, dispenser

. SPRING, compression

. DOOR, dispenser

. PAD, foam, die-cut

REF

1

1

1

2

1

1

1

1 ti2066a

Ref

No.

Part No.

9

10

11

12

13

14

15

16

17

18

19

117576

198376

102598

115483

116998

101885

245679

198380

100085

100086

117275

Description Qty

. SCREW, machine, hex washer hd 8

. SCREW, door, hex 2

. SCREW, cap, socket head

. NUT, lock

2

5

. FITTING, hose, barb

. SCREW, cap, socket head

. BLOCKING, mounting

. PLATE, slide

2

2

1

3

. SCREW, thumb

. WASHER

. STUD, button, snap

6

6

3

Graco Phone Number

TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:

1–800–690–2894 Toll Free.

All written and visual data contained in this document reflect the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

This manual contains English: MM 311068

Graco Headquarters: Minneapolis

International Offices: Belgium, Korea, China, Japan

GRACO INC.

P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

www.graco.com

PRINTED IN USA 3/2005, Rev. 3/2006

8 311068

advertisement

Related manuals

advertisement