Graco 313938H - LD Series Enclosed Hose Reels Instructions

Add to my manuals
26 Pages

advertisement

Graco 313938H - LD Series Enclosed Hose Reels Instructions | Manualzz

Instructions

LD Series Enclosed

Hose Reels

313938H

EN

For dispensing air, water, antifreeze, windshield washer solvent, transmission fluid, oil and grease. Not recommended for outdoor use.

Not approved for use in European explosive atmosphere locations.

Part Numbers and Models: Pages 4-6

Important Safety Instructions

Read all warnings and instructions in this manual. Save these instructions.

Community Design Registration Number: 0012097

12-0001

Registration Number: ZL201030154438.8

Taiwan Patent Number: D140640

US Patent: D637.067

Korea Patent: 30608479

Patents Pending ti13505

2

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable.

WARNING

FIRE AND EXPLOSION HAZARD

When flammable fluids are present in the work area, such as gasoline and windshield wiper fluid, be aware that flammable fumes can ignite or explode. To help prevent fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources, such as cigarettes and portable electric lamps.

• Keep work area free of debris, including rags and spilled or open containers of solvent and gasoline.

• Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.

• Ground all equipment in the work area.

• Use only grounded hoses.

• If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem.

• Keep a working fire extinguisher in the work area.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS forms from distributor or retailer.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only.

• Do not alter or modify equipment.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

SKIN INJECTION HAZARD

High-pressure fluid from dispense valve, hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

• Do not point dispense valve at anyone or at any part of the body.

• Do not put your hand over the end of the dispense nozzle.

• Do not stop or deflect leaks with your hand, body, glove, or rag.

• Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment.

PRESSURIZED ALUMINUM PARTS HAZARD

Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in pressurized aluminum equipment. Such use can cause serious chemical reaction and equipment rupture, and result in death, serious injury, and property damage.

313938H

Warnings

WARNING

MOVING PARTS HAZARD

Moving parts can pinch or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.

PRESSURIZED EQUIPMENT HAZARD

Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury.

• Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment.

• Tighten all fluid connections before operating the equipment.

• Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.

313938H 3

4

Models

Models

*The last character of each Model No. indicates the hose reel color. For example: D = black. On the table below this last character is represented by the generic # symbol. For example, to show the complete model number for a black

HEL13# model hose reel, the # symbol in the table is replaced with “D”. The complete model number is: HEL13D.

Model No.*

HEL13#

HEL15#

HEL23#

HEL25#

HEL33#

HEL34#

HEM23#

HEM33#

Application

Air Only

Air Only

Air / Water

Air / Water

Hose Size

6 mm x 10 m

6 mm x 15 m

10 mm x 10 m

10 mm x 15 m

Air / Water 12 mm x 10 m

Air / Water 10 mm x 14 m

Oil

Oil

10 mm x 10 m

12 mm x 10 m

250

250

250

1800

1800

PSI

250

Maximum Pressure

Bar Mpa

17.2

1.7

250

250

17.2

17.2

1.7

1.7

17.2

17.2

17.2

124.0

124.0

HEH13# Grease 6 mm x 10 m 5000 345

Must be ordered separately. See page 23 for additional information.

1.7

1.7

1.7

12.4

12.4

34.5

Inlet Kit

24C437

24C437

24C438

24C438

24C438

24C438

24C440

24C441

24C442

Replacement Hose Reels

NOTE: The replacement hose reel models listed in the following table are also used in the hose reel packages listed

on page 5. Refer to this table for the related Application, Hose Size and Maximum Pressure data for both replace-

ment hose reels and the related hose reel packages.

Additional Technical Data is provided on pages 24 and 25.

BSPT

Model No.

24F789

24F790

24F791

24F792

24F793

24F794

24F795

24F796

24F797

BSPP

Model No.

24J126

24J127

24J128

24J129

24J130

24J131

24J132

24J133

24J134

NPT

Model No.

24H655

24H656

24H657

24H658

24H659

24H660

24H661

24H662

24H663

Application

Air Only

Air Only

Air / Water

Air / Water

Air / Water

Air / Water

Oil

Oil

Grease

Hose Size

6 mm x 10 m

6 mm x 15 m

10 mm x 10 m

10 mm x 15 m

12 mm x 10 m

10 mm x 14 m

10 mm x 10 m

12 mm x 10 m

6 mm x 10 m

PSI

Maximum Pressure

Bar Mpa

250

250

17.2

17.2

1.7

1.7

250

250

250

250

17.2

17.2

17.2

17.2

1.7

1.7

1.7

1.7

1800

1800

5000

124.0

124.0

345

12.4

12.4

34.5

313938H

Models

LD Enclosed Hose Reel Packages Model Numbers

Each hose reel package includes a replacement hose reel, mounting bracket and inlet kit. Application, hose size and maximum pressure rating details for each replacement hose reel are provided on the Replacement Hose Reels table

on page 4. This information also pertains to the packages that include the replacement hose reel as listed on the

tables below. See page 23 for Bracket and Inlet Kit descriptions.

Wall Mounted Hose Reel: Includes Wall Mount

Bracket Kit 24G866

Model No.

24F744

24F745

24F746

24F747

24F748

24F749

24F750

24F751

24F752

24F735

24F736

24F737

24F738

24F739

24F740

24F741

24F742

24F743

24J258

24J259

24J260

24J261

24J262

24J263

24J264

24J265

24J266

★ Included in package.

Replacement

Hose Reel

NPT

24H655

24F796

24F797

BSPP

24J126

24J127

24J128

24J129

24J130

24J131

24J132

24J133

24J134

24H656

24H657

24H658

24H659

24H660

24H661

24H662

24H663

BSPT

24F789

24F790

24F791

24F792

24F793

24F794

24F795

Inlet Kit

24J253

24J253

24J254

24J254

24J254

24J254

24J255

24J256

24J257

24C437

24C437

24C438

24C438

24C438

24C438

24C440

24C441

24C442

24C443

24C443

24C444

24C444

24C444

24C444

24C537

24C538

24C539

Hose Reel with Fixed Bracket: Includes Fixed

Mount Bracket Kit 24G865

Model No.

.

24F753

24F754

24F755

24F756

24F757

24F758

24F759

24F760

24F761

24F762

24F763

24F764

24F765

24F766

24F767

24F768

24F769

24F770

24J267

24J268

24J269

24J270

24J271

24J272

24J273

24J274

24J275

★ Included in package.

Replacement

Hose Reel

NPT

24H655

24F796

24F797

BSPP

24J126

24J127

24J128

24J129

24J130

24J131

24J132

24J133

24J134

24H656

24H657

24H658

24H659

24H660

24H661

24H662

24H663

BSPT

24F789

24F790

24F791

24F792

24F793

24F794

24F795

Inlet Kit

24J253

24J253

24J254

24J254

24J254

24J254

24J255

24J256

24J257

24C437

24C437

24C438

24C438

24C438

24C438

24C440

24C441

24C442

24C443

24C443

24C444

24C444

24C444

24C444

24C537

24C538

24C539

313938H 5

Models

Hose Reel with Swivel Bracket and Inlet Kit:

Includes Swivel Bracket Kit 24C772

Model No.

24F780

24F781

24F782

24F783

24F784

24F785

24F786

24F787

24F788

24F771

24F772

24F773

24F774

24F775

24F776

24F777

24F778

24F779

24J276

24J277

24J278

24J279

24J280

24J281

24J282

24J283

24J284

★ Included in package.

Replacement

Hose Reel

NPT

24F795

24F796

24F797

BSPP

24J126

24J127

24J128

24J129

24J130

24J131

24J132

24J133

24J134

24H655

24H656

24H657

24H658

24H659

24H660

24H661

24H662

24H663

BSPT

24F789

24F790

24F791

24F792

24F793

24F794

Inlet Kit ★

24J253

24J253

24J254

24J254

24J254

24J254

24J255

24J256

24J257

24C437

24C437

24C438

24C438

24C438

24C438

24C440

24C441

24C442

24C443

24C443

24C444

24C444

24C444

24C444

24C537

24C538

24C539

6 313938H

Installation

Installation

A ground wire (G), bleed-type master air valve (E) and

fluid drain valve (H) are required in your system installation. These components help reduce the risk of serious injury, including electric shock and splashing in your eyes or on the skin.

• The ground wire must be connected to the pump grounding lug and to a true each ground according to your local code.

• The bleed-type master air valve relieves air trapped between this valve and the pump after the air is shut off. Trapped air can cause the pump to cycle unexpectedly Locate the valve close to the pump.

• The fluid drain valve assists in relieving fluid pressure in the displacement pump, hose and gun. Triggering the valve to relieve pressure may not be sufficient.

Typical Installation Layout

A

L

F

D

E

B

G

C

H J

K

F

IG

. 1

A Main air supply

B Pump air supply

C Air filter

D Air regulator

E Bleed-type master air valve (required)

F Pump

G Pump grounding wire (required)

H Thermal relief valve (required)

J Dump valve (required)

K Fluid shut-off valve

313938H

L Fluid line

M Hose reel

N Dispensing valve

P Flexible inlet hose

M

N ti13981

K

P

7

8

Installation

Wall Mounting

To reduce the risk of injury, be sure the mounting surface is strong enough to support the reels, weight of the lubricants and stress caused by hard pulls on the

service hoses. See Technical Data, page 21 for

weights of hose reel assemblies.

1.

2.

3.

ti13506

4.

ti13507

3.0 m (10 ft) maximum to floor ti13508

6 mm (1/4 in.) minimum

313938H

5.

7.

ti13510

8.

6.

Align ti13511

Installation

CLICK

313938H 9

Installation

Overhead Mounting

To reduce the risk of injury, be sure the mounting surface is strong enough to support the reels, weight of the lubricants and stress caused by hard pulls on the

service hoses. See Technical Data, page 21 for

weights of hose reel assemblies.

1.

2.

3.

4.

3.0 m (10 ft.) maximum to floor

10

6 mm (1/4/ in.) minimum

313938H

5.

CLICK

6.

Align ti13511

7.

Installation

313938H 11

Installation

Flushing

Before installing meter or dispense valve to end of hose, flush supply line with a compatible solvent such as Stoddard solvent or mineral spirits.

1.

Place end of hose in waste container.

2.

Blow out entire lubricant supply line with air

3.

Flush equipment with a compatible solvent until fluid runs clear.

4.

Pump dispensing lubricant through line until all solvent is flushed out.

12 313938H

Repositioning Hose Stopper (optional)

1.

2.

Repositioning Hose Stopper (optional) ti13525

3.

313938H 13

Installing Meter

Installing Meter

1.

14 313938H

Adjusting Spring Tension

Adjusting Spring Tension

IMPACT HAZARD

The spring is always under great tension and could be propelled or uncoil with enough force to cause serious injury.

• The hose reel spring is not a serviceable part. Do not attempt to replace or service the spring.

• Always grasp ratchet handle firmly with both hands when adjusting tension.

• When decreasing spring tension, never attempt to turn ratchet more than 1/4 turn with each push-in motion.

Uncontrolled spinning of the hose reel could cause serious injury if you are hit by the hose or a tool.

• Never allow reel to spin freely.

• The reel must be bolted securely in place when making adjustments.

Increasing Tension

Table 1: Recommended Turns to Set and Decrease Spring Tension

Model

4

Approximate No. of Turns

Full Turns to Increase

Spring Tension

1/4 Turns to Decrease Spring

Tension

16 HEL13#, 24F735, 24F744, 24F753, 24F762,

24F771, 24F780, 24J258, 24J267, 24J276

HEL15#, 24F736, 24F745, 24F754, 24F763,

24F772, 24F781, 24J259, 24J268, 24J277

HEL23#, 24F737, 24F746, 24F755, 24F764,

24F773, 24F782, 24J260, 24J269, 24J278

HEL25#, 24F738, 24F747, 24F756, 24F765,

24F774, 24F783, 24J261, 24J270, 24J279

HEL33#, 24F739, 24F748, 24F757, 24F766,

24F775, 24F784, 24J262, 24J271, 24J280

HEM23#, 24F741, 24F750, 24F759, 24F768,

24F777, 24F786, 24J264, 24J273, 24J282

HEM33#, 24F742, 24F751, 24F760, 24F769,

24F778, 24F787, 24J265, 24J274, 24J283

HEH13#, 24F743, 24F752, 24F761, 24F770,

24F779, 24F788, 24J266, 24J275, 24J284

HEL34#, 24F740, 24F749, 24F758, 24F767,

24F776, 24F785, 24J263, 24J272, 24J281

3

4

4

4

5

7

6

4

12

16

16

16

20

28

24

16

313938H 15

Adjusting Spring Tension

1.

2.

ti13515

1/4

Turn

ti13516

16 313938H

Decreasing Spring Tension

Decreasing Spring Tension

1.

2.

Push in on ratchet. Grasp handle firmly with both hands; then turn ratchet counter-clockwise 1/4 turn

ONLY.

Repeat this procedure of pushing in and turning ratchet counter-clockwise, ONLY 1/4 turn at a time, until spring tension has been completely released.

See Table 1, page 15 for the recommended number

of 1/4 turns needed to completely release the spring tension.

1/8

Turn

Push In

ti13516

1/4 Turn

ONLY!

ti13517

3.

----------------------

1/8

Turn

Out

ti13518

313938H 17

Operation

Operation

18 313938H

Repair and Maintenance

Pressure Relief Procedure

1.

2.

Repair and Maintenance ti13524 ti13523

313938H 19

Disassembly

1.

2.

ti13512

3.

ti13513-2 ti13514

Parts

1d

1k

1 ★

1j

1e

1 ◆

1j

1f/1g

1m

1‡

1c

1b

16

1a

24

6

19

Parts

23

2

8

11

15

12

7

32

31

30

29

25 28 17

27

26

TI14425

313938H 21

Parts

Ref Part No. Description

12

15

16

17

1a‡ ◆

1b‡ ◆

1c‡ ◆

1d ◆

1e

1f ◆

1g ◆

1h ★

1j ★

1k ★

1m ★

2

6

7

8

11

1‡

1 ◆

1 ★

15Y706

24E319

16C019

BRACKET, swivel, included in all HEL,

HEM and HEH models and models

24F735 - 24F752

BRACKET, fixed, included in models

24F753-24F770

BRACKET, fixed, bench mounted, included models 24F771-24F788

. CAP, mounting tube

. TUBE, mounting

. CLIP, button clip

. BRACKET, roller A

. BRACKET, roller B

. PIN, roller

. ROLLER, hose

. SCREW, machine, pan head

. WASHER

. BOLT

. NUT

SCREW, mach pan hd

ENCLOSURE (B)

ADJUSTER, power spring

SCREW, recessed pan hd

SPRING, adjuster

TUBE, shaft

CAP, shaft

SPOOL

262214 HOSE, 6 mm id x 10 m

262216 HOSE, 6 mm id x 15 m

262218 HOSE, 10 mm id x 10 m

262220 HOSE, 10 mm id x 15 m

262222 HOSE, 12 mm id x 10 m

262232 HOSE, 12 mm id x 14 m

262224 HOSE, 10 mm id x 10 m

262226 HOSE, 12 mm id x 10 m

262227 HOSE,6 mm id x 10 m

262584 HOSE, 6 mm id x 10 m

262585 HOSE, 6 mm id x 15 m

262586 HOSE, 10 mm id x 10 m

262587 HOSE, 10 mm id x 15 m

262588 HOSE, 12 mm id x 10 m

17

(cont)

262589 HOSE, 10 mm id x 10 m

262590 HOSE, 12 mm id x 10 m

262591 HOSE, 6 mm id x 10 m

262592 HOSE, 12 mm id x 14 m

24J295 HOSE, 6 mm id x 10 m

24J296 HOSE, 6 mm id x 15 m

24J297 HOSE, 10 mm id x 10 m

24J298 HOSE, 10 mm id x 15 m

24J299 HOSE, 12 mm id x 10 m

24J300 HOSE, 12 mm id x 14 m

24J301 HOSE, 10 mm id x 10 m

Qty

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

3

1

1

1

1

11

1

1

2

2

1

2

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

Ref Part No. Description Qty

23

24

25

26

19

27

28

29

30

31

24J302 HOSE, 12 mm id x 10 m

24J303 HOSE,6 mm id x 10 m

24C531

KIT, swivel, air, A/W (24F789, 24F790,

24F791, 24F792, 24F793, 24F794,

24J126, 24J127, 24J128, 24J129,

24J130, 24J131, and HEL models)

24C532

24C533

24H474

24H475

KIT, swivel, oil (24F795, 24F796,

24J132, 24J133, and HEM models)

KIT, swivel, grease (24H797, 24J134, and HEH models)

KIT, swivel, air, A/W (models 24H655,

24H656, 24H657, 24H658, 24H659,

24H660)

KIT, swivel, air, A/W (models 24H661 and 24H662)

24H476 KIT, swivel, grease (model 24H663)

ENCLOSURE (A)

FITTING

ROLLER, hose guide

SCREW, mach, phil, pn hd

178029 STOP, hose, 1/2” od

178030 STOP, hose, 5/8” od

178031 STOP, hose, 3/4” od

101324 NUT, hex, jam

SCREW, countersunk head

WASHER, id 6.4, od 18

LATCH

1

1

1

1

1

1

1

32 SPRING, latch

33 ▲ 15W036 LABEL, Warning

1

1

▲ Replacement Danger and Warning labels, tags and cards are available at no cost.

2

2

2

2

1

1

1

1

2

1

1

2

22 313938H

Parts

Mounting Bracket Kits

All HEL, HEM and HEH Models

‡ 24G866

KIT, Hose Reel Wall Mounting Bracket.

◆ 24G865 KIT, Hose Reel Fixed Installation Kit.

★ 24C772 KIT, Hose Reel Bench Mounting Bracket.

Inlet Kits

To determine the correct Mounting Bracket and/or Inlet

Kit to order for your hose reel model, see tables on

pages 4, 5, and 6.

Ordering the Correct Kit for Your Hose Reel

24C437 KIT, hose, 1/4”, air, BSPT

24C438 KIT, hose 3/8” and 1/2”, A/W, BSPT

24C440 KIT, hose 3/8” and 1/2” oil, BSPT

24C442 KIT, hose, 1/4”, grease, BSPT

24C441 KIT, hose 1/2”, oil, BSPT

24C443 KIT, hose 1/4”, air, NPT

24C444 KIT, hose, 3/8”, A/W, NPT

24C537 KIT, hose, 3/8” oil, NPT

24C538 KIT, hose, 1/2” oil, NPT

24C539 KIT, hose, 1/4”, grease, NPT

24J253 KIT, hose 1/4”, air, BSPP

24J254 KIT, hose, 3/8”, A/W, BSPP

24J256 KIT, hose, 3/8” oil, BSPP

24J257 KIT, hose, 1/2” oil, BSPP

24J253 KIT, hose, 1/4”, grease, BSPP

24H661

24H662

24H663

24J126

24J127

24J128

24J129

24J130

24J131

24J132

24J133

24J134

Replacement

Reel

24F789, HEL13#

Hose Kit (17) Swivel Kit (19) Stop (27)

262214 24C531 178029

24F790, HEL15#

24F791, HEL23#

262216

262218

24C531

24C531

178029

178030

24F792, HEL25#

24F793, HEL33#

24F794, HEL34#

24F795,HEM23#

262220

262222

262232

262224

24C531

24C531

24C531

24C532

178030

178031

178031

178030

24F796, HEM33#

24F797, HEH13#

24H655

24H656

24H657

24H658

24H659

24H660

262226

272227

262584

262584

262585

262586

262587

262588

24C532

24C533

24H474

24H474

24H474

24H474

24H474

24H474

178031

178029

178029

178029

178030

178030

178031

178031

262592

262590

262591

24J295

24J296

24J297

24J298

24J299

24J300

24J301

24J302

24J303

24H475

24H475

24H476

24C531

24C531

24C531

24C531

24C531

24C531

24C532

24C532

24C533

178030

178031

178029

178029

178029

178030

178030

178031

178031

178030

178031

178029

313938H 23

Technical Data

Technical Data

In the following table, Technical Data is provided for the HEL, HEM and HEH hose reel models and for the replace-

ment hose reels. Refer to the Package Model Numbers table on page 5 to verify which replacement hose model is

included in your hose reel package. Additional hose reel information, including Application, Hose Sizes and Maxi-

mum Working Pressure Ratings is provided on pages 4 and 5.

Models

H/24F = BSPT

Temperature

Range C° (F°)

Inlet

( BSPT,

NPT,

BSPP)

1/2 in.

HEL13#, 24F789,

24H655, 24J126

HEL15#, 24F790,

24H656, 24J127

HEL23#, 24F791,

24H657, 24J128

HEL25#, 24F792,

24H658, 24J129

HEL33#, 24F793,

24H659, 24J130

HEL34#, 24F794,

24H660, 24J131

HEM23#, 24F795,

24H661, 24J132

HEM33#, 24F796,

24H662, 24J133

HEH13#, 24F797,

24H663, 24J134

Sound Data All Models

-10°C - 60°C

(14°F - 140°F)

-10°C - 60°C

(14°F - 140°F)

-17.8°C - 60°C*

(0°F - 140°F)

-17.8°C - 60°C*

(0°F- 140°F)

-17.8°C - 60°C*

(0°F - 140°F)

-17.8°C - 60°C*

(0°F - 140°F)

-17.8°C - 60°C

(0°F - 140°F)

-17.8°C - 60°C

(0°F - 140°F)

-17.8°C - 60°C

(0°F - 140°F)

Sound Pressure: 69.3 dB(A)†

1/2 in.

1/2 in.

1/2 in.

1/2 in.

1/2 in.

1/2 in.

1/2 in.

3/8 in.

Outlet

( BSPT,

NPT,

BSPP)

Weight

1/4 in.

9.0 kg

19.8 lb

1/4 in.

9.5 kg

21 lb

3/8 in.

10.4 kg

23 lb

3/8 in.

11.0 kg

24.25 lb

1/2 in.

10.5 kg

23.1 lb

1/2 in.

11.4 kg

25.1 lb

3/8 in.

11.4 kg

25.1 lb

1/2 in.

14.0 kg

30.8 lb

1/4 in.

13.2 kg

29.1 lb

Wetted Parts

Aluminum, Buna-N Rubber, PVC

Aluminum, Buna-N Rubber, PVC

Aluminum, Buna-N Rubber

Aluminum, Buna-N Rubber

Aluminum, Buna-N Rubber

Aluminum, Buna-N Rubber

Carbon Steel, Buna-N Rubber, PTFE

Carbon Steel, Buna-N Rubber, PTFE

Carbon Steel, Buna-N Rubber

Sound Power: 75.3 dB(A)†

*0°C - 60°C (32°F - 140°F) for Water Applications.

† Tested in accordance with ISO9614-2 with an assumed operator position.

24 313938H

Technical Data

Mounting Pattern

6 mm (1/4 in.) bolts

50 mm

(1.97 in.)

171 mm (6.73 in.)

Dimensions

650 mm

(25.6 in.)

470 mm

(18.5 in.)

180 mm

(7.1 in.)

313938H 25

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by

Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED

TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy

(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT

MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

For the latest information about Graco products, visit www.graco.com.

TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.

Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM 313938

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441

Copyright 2009, Graco Inc. is registered to ISO 9001 www.graco.com

Revised 09/2011

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals