Graco 3A4032B, Xtreme-Duty™ Agitator and Packages Owner's Manual

Add to my manuals
22 Pages

advertisement

Graco 3A4032B, Xtreme-Duty™ Agitator and Packages Owner's Manual | Manualzz

Operation and Parts

Read all warnings and instructions in this manual and in related manuals. Save all instructions.

100 psi (7.0 bar, 0.7 MPa) Maximum Air

Input Pressure

See page 3 for model information.

3A4032B

EN

PROVEN QUALITY. LEADING TECHNOLOGY.

Related Manuals ................................................ 3

Model Information ............................................... 3

Warnings ........................................................... 4

System Component Identification......................... 7

Installation.......................................................... 8

Grounding ................................................... 8

Assembling and Positioning the

Agitator .......................................... 9

Attaching the Blades .................................... 10

Air Connections ........................................... 11

Fluid Accessories......................................... 12

Operation ........................................................... 13

Pressure Relief Procedure............................ 13

Setup .......................................................... 13

Using the Elevator (included in some packages) ...................................... 14

Using the Agitator ........................................ 14

Using the Feed Pump(included in some packages) ...................................... 14

Service .............................................................. 15

Flushing the Agitator Air Motor ...................... 15

Lubricating the Agitator Air Motor .................. 15

Notes................................................................. 16

Parts.................................................................. 17

Xtreme-Duty Agitator 25A598 ....................... 17

Xtreme-Duty Agitator Drive Train .................. 18

Xtreme-Duty Agitator Packages 25A599 –

25A604 .......................................... 20

Technical Data ................................................... 21

Graco Standard Warranty.................................... 22

2 3A4032B

Related Manuals

Component Manuals in English:

306287

308118

307044

308738

307043

306982

Elevators and pump supports

SST feed pumps, 5:1 and 10:1 ratio

CS feed pump, 5:1 ratio

CS feed pump, 10:1 ratio

Monark ® air motors

President ® air motors

For maximum air and fluid working pressures and agency approvals of package components, see appropriate component manual.

Xtreme-Duty Agitator

II 1/2 G c IIC T4

ITS 16 ATEX 100984

0°C≤Ta≤50°C

AGITATOR ON DRUM

COVER

Xtreme-Duty Agitator

25A598

Drum cover with recirculation kit

AGITATOR WITH

ELEVATOR

AGITATOR WITH

ELEVATOR AND FEED

AGITATOR WITH

ELEVATOR AND FEED

AGITATOR WITH

ELEVATOR AND FEED

AGITATOR WITH

ELEVATOR AND FEED

Xtreme-Duty Agitator

25A598

Xtreme-Duty Agitator

25A598

Xtreme-Duty Agitator

25A598

Xtreme-Duty Agitator

25A598

Xtreme-Duty Agitator

25A598

Drum cover with recirculation kit

Drum cover with feed and recirculation kit

Drum cover with feed and recirculation kit

Drum cover with feed and recirculation kit

Drum cover with feed and recirculation kit

Handles on drum cover

Elevator with support attachments

Elevator with support attachments

Elevator with support attachments

Elevator with support attachments

Elevator with support attachments

– – – – –

– – – – –

5:1 CS Monark

5:1 SST

Monark

10:1 CS

President

10:1 SST

President

3A4032B 3

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these

Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.

or solvent flowing through the equipment can cause static sparking. To help prevent fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static sparking).

• Never spray or flush solvent at high pressure.

• Keep work area free of debris, including solvent, rags and gasoline.

• Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes are present.

• Use only grounded hoses.

• Hold gun firmly to side of grounded pail when triggering into pail. Do not use pail liners unless they are anti-static or conductive.

equipment until you identify and correct the problem.

• Keep a working fire extinguisher in the work area.

Fluid from the equipment, leaks, or ruptured components can splash in the eyes or on skin and cause serious injury.

cleaning, checking, or servicing equipment.

• Tighten all fluid connections before operating the equipment.

• Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.

4

Moving parts can pinch, cut or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Pressurized equipment can start without warning. Before checking, moving, or servicing

3A4032B

Warnings

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.

• Read Safety Data Sheet (SDS) to know the specific hazards of the fluids you are using.

• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

Wear appropriate protective equipment when in the work area to help prevent serious injury, including eye injury, hearing loss, inhalation of toxic fumes, and burns. Protective equipment includes but is not limited to:

• Protective eyewear, and hearing protection.

• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.

3A4032B 5

6

Warnings

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request Safety Data Sheet (SDS) from distributor or retailer.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modifications may void agency approvals and create safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

3A4032B

System Component Identification

A

B

C

D

F

G

H

Agitator air motor and gear reducer

Xtreme-Duty agitator blade

Agitator shaft and coupler

Stainless steel drum cover

Recirculation tube

Ground wire with clamp

Feed pump strainer

J

K

L

M

N

P

Drum cover elevator

Drum cover support (for elevator)

Feed pump

Pump air control

Agitator air control

Elevator air control

3A4032B 7

Installation

AL

AF ti28844a

RG

MT

AF*

AL*

Air Supply Line Filter

Air Supply Line Lubricator

AM Agitator Motor

MT* Mix Tank (reference only)

RG* Air Regulator and Gauge

* Items not supplied.

AM

The equipment must be grounded to reduce the risk of static sparking. Static sparking can cause fumes to ignite or explode. Grounding provides an escape wire for the electric current.

To ground the agitator, connect one end of the ground wire (G) to the ground connector (GC) on the side of the agitator and/or drum cover. Connect the clamp end of the ground wire to a true earth ground.

For an additional ground wire and clamp, order Part

237569.

8 3A4032B

Installation

To reduce the risk of fire and explosion, always maintain a minimum of 1 in. clearance inside the material drum between rotating agitator parts and any other objects, including the drum to prevent sparks from contact. This includes the edges of the drum as well as any item which may be inserted into the drum from another opening, such as feed pumps or suction tubes.

When included in a package without an elevator, the drum cover is provided with handles for easy lifting and positioning. For additional handles, order the

Handles Kit, part 237524.

Place two standard 55 U.S. gallon (45 Imperial gallon, 200 L) drums 14 in. (36 cm) apart, and center the drum cover on the barrels.

To reduce the risk of injury from being crushed by equipment, do not go under the elevator when it is raised.

Mount the drum cover as described in the Elevators and Pump Supports Manual 306287. The elevator must be in the down position when you do any work on the elevator, agitator, or drum cover assembly.

1.

Install the four lock nuts (A2) holding the agitator to the drum cover.

2.

Tighten the lock nuts to 30 ft-lb (40.6 N • m).

3A4032B 9

Installation

The drum cover must be secured to the drum to ensure proper clearance of rotating parts and prevent vibration. If using the drum cover without an elevator, the cover must be secured by clamping or other means. For open-headed drums with closing ring, make sure the lever-lock or closing bolt is fastened securely before operating.

1.

Slide the agitator blade assembly (B1) onto the shaft (C1), positioned so that the blade coupling screws (B2) will contact the flats of the shaft.

Apply thread sealant (supplied with the blades) to screws (B2).

If the Xtreme-Duty agitator is being mounted on a custom drum cover, sufficient clearance must be provided around any moving parts. See the image below for the hole mounting pattern and minimum clearance required.

2.

Adjust the height of the blade assembly as desired and tighten two screws (B2) to attach the blades onto the shaft. Tighten to 13 ft-lb (17.6

N • m).

3.

Apply thread sealant to screw (C3) and tighten to

12–20 in-lb (1.3–2.3 N • m).

4.

Slide the shaft coupler (C2) onto the output shaft of the agitator drive (A1) up to the mid point of the coupler screws. Tighten to 15 ft-lb (20 N • m).

5.

Slide the blade shaft (C1) into the coupler and tighten two screws to attach the shaft to the coupler. Tighten to 15 ft-lb (20 N • m).

10 3A4032B

Installation

Connect an electrically conductive 1/2 in. ID (minimum) air hose to supply air to the system air controls.

Packages without an elevator will not have an elevator control, and packages without a feed pump will have the connection for the pump air hose plugged. Install an air filter upstream of the system to remove harmful dirt and moisture from the air supply. To order an air filter, order part 106148 (3.8 in. npt, 20–micron element, 5 oz.

bowl, without gauge).

SA

LB

RG

EF

AR

EC

AS

FP

Air Restrictor (Elevator Speed)

Elevator Control Selector

Agitator Shut Off Valve

Feed Pump Shut Off Valve

Supply Air Inlet

Agitator Lubricator

Agitator Regulator and Gauge

Elevator Air Fitting

If installing an elevator, reference the Installation section of the Elevators and Pump Supports Manual 306287*.

To connect the elevator air control, insert 1/4 in. OD air tubing into the tube-connect fitting of the resistor valve

(AR) on the back of the elevator air control. Insert the other end into the elevator air fitting (AF).

* Install the elevator air fitting (EF, included with the elevator air control) into the port on top of the elevator riser tube.

3A4032B 11

Installation

If using a feed pump, insert the pump into one of the two 2 in. npt bungs in the drum cover. The pump may be mounted on either side. Follow the installation instructions in the pump manual.

Connect the air hose from the air control tee fitting

A 3/4 in. feed hose is included with some packages.

Install the hose into the strainer on the outlet of the pump and connect the other end to the inlet of the proportioning system or other equipment.

A fluid drain valve is required to connect to the fluid outlet of the pump. See the pump manual for details.

The drum cover also has two 1 in. npt ports (which have 1–1/2 in. npt male threads underneath the cover) which can be used for installing refill lines or suction tubes.

A recirculation tube can be inserted into a strain relief bushing installed in one of the two 2 in. bung plugs.

The bung plug has a 1/2 in. ID knockout feature which keeps the bung sealed if a recirculation tube is not used.

To install a recirculation tube, remove the strain relief bushing from the bung plug and place a tube, punch or other item against the knockout and strike with a hammer. Make sure that any plastic is cleared from the underside of the plug.

Once the knockout is removed, reinstall the strain relief bushing and insert the recirculation tube.

Tighten the bushing against the tube to seal and hold in place.

BP

KN

PA

RT

Bung Plug

Knockout

Pump Air Controls

Recirculation Tube

12

BS

PA

BP

RP

Bushing

Pump Air Hose

Bung Plug

Refill Port

3A4032B

Operation

Follow the Pressure Relief Procedure whenever you see this symbol.

This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid such as splashing fluid and moving parts, follow the Pressure Relief

Procedure before cleaning, checking, or servicing the equipment.

1.

Close the agitator shut-off valve.

2.

Shut off the air supply to any accessories such as feed pumps or an elevator.

To reduce the risk of serious injury from moving parts and splashing fluid, always shut off the agitator before you raise, check, or repair the agitator.

1.

Before turning on supply air, make sure all valves are in the CLOSED or OFF position.

a.

For elevator packages, make sure that the elevator control selector is in the OFF position.

b.

Make sure that the agitator shut-off valve is

CLOSED.

c.

If using a feed pump, make sure that the pump shut-off valve is CLOSED.

2.

Turn on the air supply to the system.

AR

EC

AS

FP

SA

LB

RG

Air Restrictor (Elevator Speed)

Elevator Control Selector

Agitator Shut Off Valve

Feed Pump Shut Off Valve

Supply Air Inlet

Agitator Lubricator

Agitator Regulator and Gauge

3A4032B 13

Operation

Refer to the Elevators and Pump Supports Manual

306287 for detailed information about using the elevator.

The elevator air control has three settings: RAISE,

OFF, and RUN.

• RAISE allows the elevator to be raised and disables the agitator and feed pump air.

• OFF turns off all air pressure. If the elevator is raised, OFF will lower the elevator.

• RUN enables the agitator and feed pump air.

A restrictor valve on the elevator air line slows the elevator for safe operation.

To prevent air motor failure and possible damage to equipment, always keep the air motor properly lubricated.

The Xtreme-Duty Agitator is provided with an air line lubricator to aid in proper maintenance. Fill the lubricator with SAE #10 light oil and set the lubricator feed rate at 1 drop of oil per minute for high speed or continuous duty usage. Do not overfeed oil or exhaust air may become contaminated. To manually lubricate the air motor, see

Lubricating the Agitator Air Motor, page 15

.

Make sure that the agitator shut-off valve is in the

CLOSED position and the regulator is turned all the way down.

If used, turn the elevator control to RUN.

Turn the agitator shut-off valve to the OPEN position.

Slowly open the regulator valve to increase agitator speed until the desired speed is reached.

Fluid under high pressure can be injected through the skin and cause serous injury. To reduce the risk of an injury from injection, splashing fluid, or moving parts, follow the Pressure Relief Procedure whenever you:

• are instructed to relieve the pressure,

• stop spraying,

• check or service any of the system equipment,

• or install or clean the spray tips.

Refer to the feed pump manual and component manual for any dispense equipment used for specific operation and pressure relief instructions.

For feed pump pressure relief information, refer to the appropriate feed pump manual.

Related Manuals, page 3

.

Excessive agitator speed may cause vibration, foaming of fluid, and increased wear on parts.

14 3A4032B

Service

Hazardous fluids or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin, swallowed, or inhaled. When flushing the air motor, keep your face away from the exhaust port, and wear the appropriate protective clothing, gloves, eyewear, and respirator.

To prevent air motor failure and possible damage to equipment, always keep the air motor properly lubricated.

If an air line lubricator is not installed, the air motor must be manually lubricated every 8 hours. Lubricate the agitator air motor by placing 10–20 drops of SAE

#10 light oil in the motor’s air inlet. Run the agitator for about 30 seconds.

Do not use kerosene or other flammable solvents to flush the air motor. Flushing with flammable solvents could cause fire or explosion and result in serious injury or property damage.

If the air motor is sluggish or inefficient, follow this procedure in a well ventilated area.

1.

Disconnect the air line and muffler (08) from the motor (W).

2.

Add several teaspoons of non-flammable solvent, or spray the solvent directly into the motor air tube connector (R).

Gear Reducer: After the first 100 hours or two weeks of operation, remove the oil plug (T) and the oil level plug (S), drain the oil, and thoroughly flush the housing with light flushing oil.

Refill with Graco oil (part 217374) to the proper level.

Afterward, change the oil every six months or

2500 hours of operation (whichever occurs first) under normal operating conditions. More frequent oil changes are needed under severe operating conditions or in atmospheres containing excessive moisture or abrasives. Contact your Graco distributor.

and lubricated pumps is Gast ® Flushing Solvent

(Part AH255 or AH255A) or Penetone Inhibisol ®

Safety Solvent.

3.

Reconnect the air line, and slowly increase the air pressure until there is no trace of solvent in the exhaust air.

4.

Reconnect the muffler (08).

5.

Re-lubricate the motor with a squirt of lightweight oil into the motor air tube connector (R).

Every six months or 2500 hours of operation

(whichever comes first), inspect the bearing block

(BR). This can be performed before or after gear reducer oil changes.

With the agitator running slowly, place a hand on the side of the bearing block (BR). There should be no excessive vibration or grinding. Do not attempt to repair the bearing block or gear reducer. Contact your Graco Distributor.

3A4032B 15

Notes

16 3A4032B

Parts

15

16

17

18

10

11

12

06

07

08

09

03

04

05

Ref.

Part

01 †

02 17J004

16T396

16T245

24P837

AGITATOR, drive train

BLADE, Xtreme-Duty Agitator

SHAFT, agitator

COUPLER, shaft

GASKET, agitator

109212 SCREW, cap

125204 NUT, lock, 3/8–16

129069

15R343

MUFFLER, air, exhaust

CLAMP, grounding

157021 WASHER, lock, int. tooth

C19798 SCREW, SHCS

13

14

BRACKET, air lubricator

214847 LUBRICATOR, air

156849 FITTING, nipple, 3/8 in.

15T539 REGULATOR, air

113911 GAUGE

113630 FITTING, 45 degree, 1/8 in.

155699 FITTING, elbow, 3/8 in.

3A4032B

1

1

1

1

2

1

1

1

1

1

1

1

1

1

1

1

4

4

4

1

2

3

24

25

26

27

21

22

23

Ref.

Part

19

20

113333

16F151

VALVE, ball, vented

FITTING, connector

155665

127438

BRACKET, guard, coupling

FITTING, swivel, 3/8 in.

WIRE, ground

SCREW, self-tapping

237569 WIRE, grounding

SCREW, buton, #6–32 x .38

113500 THREAD LOCKER (not shown)

Tighten nuts to 30 ft-lb (40.6 N • m) when installing onto the drum cover.

Tighten all four screws to 15 ft-lb (20.3 N • m).

Apply thread locker (27) to shaft setscrews and tighten to 13 ft-lb (17.6 N • m).

Apply thread locker (27) to screws and tighten to

1–2 ft-lb (1.3–2.7 N • m).

See

Xtreme-Duty Agitator Drive Train, page 18

for driver part details.

1

1

1

1

1

1

1

4

1

17

Parts

915

931

5 916

7 907

3

912

4 915

3 914

913

5 911

7 5 910

7 909

905

906

905

904

8 903

902

7 901

2

919

918

2

921

908 3

913

917 5

924

923

922

930

77 RR UUHH GG XX FF HH UULLVV NN RR IILLQQ MMXX UU \\ IIUURR PP

)) ,,55 (( $$ 11 '' (( ;; 33 // 22 66 ,,22 11

"" ** UURR XX QQ GG WWRR SS UUHH YY HH QQ WWVV WWDD WWLLFF FF KK DD UUJJ HH EE XX LLOOGG XX SS

"" '' LLVV FF RR QQ QQ HH FF WWDD LLUUEE HH IIRR UUHH UUHH PP RR YY LLQQ JJ IIUURR PP WWDD QQ NN

&& 22 00 33 22 11 (( 11 77 55 88 33 77 88 55 ((

"" '' RR QQ RR WWHH [[ FF HH HH GG SS VV LL00 DD [[ LLPP XX PP $$ LLUU:: 33 55

00 22 99 ,,11 ** 33 $$ 55 77 66 ++ $$ == $$ 55 ''

"" 66 WWDD \\ FF OOHH DD UURR IIPP RR YY LLQQ JJ SS DD UU WWVV

Read instruction manual.

Tag No. 15A722 Rev A

WWLL EE

929

18 3A4032B

Parts

Ref.

Part

901 16P919 SHAFT, agitator, upper

902 16U219 HOUSING, agitator

903 SEAL, PTFE

904 SPACER, shaft, agitator

905 122774 BEARING, 3/4 ID x 1–3/4 OD

906 16P920 HOUSING, bearing, agitator

907 SCREW, SHCS, 5/16–18 x

0.75

908 112222 SCREW, socket cap head

909 RING, retaining, external, 0.75

910 122761 HOUSING, alignment, hub

911 112760 COUPLING, alignment, disk,

TPE

912 16P922 BRACKET, adapter, agitator

913 C19209 WASHER, lock

914 101682 SCREW, socket cap head

915 181794 GEAR, reducer

916 16P923 COUPLER, adapter

917 100828 COUPLING, flexible

918 16T063 COLLAR, mounting

919 116940 SCREW, SHCS, 5/16–18

920 181849 COLLAR

921 101118 SCREW

1

1

1

1

2

1

2

4

1

1

1

4

1

1

1

8

1

1

2

1

2

Ref.

Part

922 111310 MOTOR, air, rotary

923 115841 FITTING, elbow

924 129069 MUFFLER, air, exhaust

929 ▲ 15A722 LABEL, warning

930 ▲ 16A614 LABEL, caution

931 120376 KEY, square, .188 x .62

5

7

8

1

2

3

4

Replacement Warning and Caution labels, signs, tags, and cards are available at no cost.

Apply pipe sealant to all non-swiveling pipe threads.

Apply low strength threadlocker.

Apply blue thread locker.

Remove four screws from gear reducer (915).

Pass them through bracket (912) and back into gear reducer (915) then torque to 150–170 in-lb

(17–19 N • m).

Leave a 0.015 in gap between each half of couplings (910, 911, 916, 917).

When ordering a replacement coupling: Remove set screw supplied with couplings (910, 916) and discard. Replace with set screw (931).

Open side of u-cup seal (903) must face down inside housing (902).

1

1

1

1

1

1

3A4032B 19

Parts

101

102

25A598

17J006

103 15T396

104* 237524

105+ 204385

106+ 237578

107+ 25C013

108# 218956

224350

239326

224348

109+^ 119992

110+^ 248829

111+^ 256653

Xtreme-Duty agitator

COVER, drum, agitator

TUBE, recirculation

KIT, handle, drum cover

ELEVATOR

SUPPORT, drum cover

AIR CONTROL, elevator

PUMP, Monark, 5:1 cs

PUMP, Monark, 5:1 sst

PUMP, President, 10:1 cs

PUMP, President, 10:1 sst

FITTING, nipple, 3/4 in.

KIT, regulator, feed pump

KIT, fluid strainer

1

1

1

1

1

1

1

1

1

1

1

1

1

1

112+^ 217382

113 128689

121378 114

115

116 121497

5

HOSE, 3/4 in., 10 ft

PLUG, 2 in. npt with 3/4 knockout

PLUG, 2 in. npt (not shown)

BUSHING, strain relief

PLUG, pipe, headless, 1 in.

npt

Tighten screws and nuts mounting to drum cover to 30 ft-lb (40.6 N • m).

* Kit includes two handles, on package 25A599 only

+ Included with packages 25A600–25A604 only

^ Included in Feed Accessory Kit 17K401

# Varies, with packages 25A601–25A604

1

1

2

1

1

20 3A4032B

Technical Data

Maximum Air Inlet Pressure

Gear Reducer Ratio

Maximum Recommended Shaft Speed

Air Consumption at 30 rpm

Air Consumption at 60 rpm

Air Consumption Maximum Free Speed at 100 psi (0.7 MPa, 7 bar)

Maximum Torque at Maximum Recommended

Speed

Stall Torque at Maximum Air Inlet Pressure

Span (Diameter) of Agitator Blades

Width of Agitator Blades

Height of Agitator Blades

Air Inlet Size

Ambient Temperature Range

Wetted Parts

Parts which may come in contact with fluid

Weight

Noise Level:

Typical operating conditions

Maximum rpm at 100 psi (0.7 MPa, 7 bar)

100 psi

20:1 shaft speed is 1/20 air motor speed

60 rpm

7 cfm at 20 psi

20 cfm at 80 psi

11 cfm at 20 psi

30 cfm at 80 psi

60 cfm

0.7 MPa, 7 bar

3.3 L/s at 1.4 bar

9.3 L/s at 5.5 bar

5.2 L/s at 1.4 bar

14 L/s at 5.5 bar

28 L/s

1000 in-lb (100 psi air pressure)

1120 in-lb

13.75 in.

3 in.

10.25 in.

113 N•m (0.7 MPa, 7 bar air pressure)

127 N•m

349 mm

76 mm

260 mm

32° F – 122° F

3/8 in. nps(f)

0° C – 50° C

303, 304, and 18–8 grades of stainless steel

303 stainless steel, PTFE, carbon steel, zinc plating

50 lb 22.6 kg

Sound pressure* 68 dB(A)

Sound power** 82 dB(A)

Sound pressure* 74 dB(A)

Sound power** 86 dB(A)

* Tested at a distance of 1 meter (3.2 feet) from equipment

* * Tested per ISO 9614–2

3A4032B 21

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use.

With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized

Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS

INCLUDING

FOR

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available.

Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO

AND

MATERIALS OR manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en

Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

For the latest information about Graco products, visit www.graco.com.

For patent information, see www.graco.com/patents.

order, contact your Graco Distributor or call to identify the nearest distributor. Phone:

Fax: 612-378-3505

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original Instructions. This manual contains English. MM 3A4032 www.graco.com

Revision B — June 2017

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals