Graco 313753G - Fine Finish HVLP 7.0/9.0/9.5 Owner's Manual

Add to my manuals
18 Pages

advertisement

Graco 313753G - Fine Finish HVLP 7.0/9.0/9.5 Owner's Manual | Manualzz

Operation, Repair, Parts

Fine Finish HVLP 7.0/9.0/9.5

313753G

EN

- For portable spray applications of fine finish coatings. For professional use only.-

240 Vac Models: 257829, 257830, 257831

120 Vac Models: 257833, 257834, 257835

Maximum Working Pressure: 10 psi (0,07 MPa, 0.7 bar)

Important Safety Instructions

Read all warnings and instructions in this manual. Save these instructions.

Registered Design No. 001147805-0001

US Patent No.: 7,950,598, 7,971,806 ti13853a

Table of Contents

Table of Contents

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Grounding and Electric Requirements . . . . . . . . 5

Component Identification . . . . . . . . . . . . . . . . . . . . 6

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Fluid Preparation . . . . . . . . . . . . . . . . . . . . . . . . . 7

Connect Fluid and Air Supply . . . . . . . . . . . . . . . 7

Pressure Relief Procedure . . . . . . . . . . . . . . . . . 7

Operation Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Sprayer Disassembly . . . . . . . . . . . . . . . . . . . . 10

Sprayer Assembly . . . . . . . . . . . . . . . . . . . . . . . 10

Turbine Replacement . . . . . . . . . . . . . . . . . . . . . . . 11

Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Parts Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 18

2 313753G

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risks. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable.

WARNING

GROUNDING

This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

• Improper installation of the grounding plug is able to result in a risk of electric shock.

• When repair or replacement of the cord or plug is required, do not connect the grounding wire to either flat blade terminal.

• The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire.

• Check with a qualified electrician or serviceman when the grounding instructions are not completely understood, or when in doubt as to whether the product is properly grounded.

• Do not modify the plug provided; if it does not fit the outlet, have the proper outlet installed by a qualified electrician.

• This product is for use on a nominal 120V/240V circuit and has a grounding plug similar to the plug illustrated in the figure below.

• Only connect the product to an outlet having the same configuration as the plug.

• Do not use an adapter with this product.

Extension Cords:

• Use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot receptacle that accepts the plug on the product.

• Make sure your extension cord is not damaged. If an extension cord is necessary, use 12 AWG

(2.5 mm

2

) minimum to carry the current that the product draws.

• An undersized cord results in a drop in line voltage and loss of power and overheating.

313753G 3

4

Warnings

WARNING

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion:

• Do not spray flammable or combustible materials near an open flame or sources of ignition such as cigarettes, motors, and electrical equipment.

• Paint or solvent flowing through the equipment is able to result in static electricity. Static electricity creates a risk of fire or explosion in the presence of paint or solvent fumes. All parts of the spray system, including the pump, hose assembly, spray gun, and objects in and around the spray area shall be properly grounded to protect against static discharge and sparks. Use Graco conductive or grounded high-pressure airless paint sprayer hoses.

• Verify that all containers and collection systems are grounded to prevent static discharge.

• Connect to a grounded outlet and use grounded extensions cords. Do not use a 3-to-2 adapter.

• Do not use a paint or a solvent containing halogenated hydrocarbons.

• Keep spray area well-ventilated. Keep a good supply of fresh air moving through the area. Keep pump assembly in a well ventilated area. Do not spray pump assembly.

• Do not smoke in the spray area.

• Do not operate light switches, engines, or similar spark producing products in the spray area.

• Keep area clean and free of paint or solvent containers, rags, and other flammable materials.

• Know the contents of the paints and solvents being sprayed. Read all Material Safety Data Sheets (MSDS) and container labels provided with the paints and solvents. Follow the paint and solvents manufacturer’s safety instructions.

• Fire extinguisher equipment shall be present and working.

• Sprayer generates sparks. When flammable liquid is used in or near the sprayer or for flushing or cleaning, keep sprayer at least 20 feet (6 m) away from explosive vapors.

ELECTRIC SHOCK HAZARD

Improper grounding, setup, or usage of the system can cause electric shock.

• Turn off and disconnect power cord before servicing equipment.

• Use only grounded electrical outlets.

• Use only 3-wire extension cords.

• Ensure ground prongs are intact on sprayer and extension cords.

• Do not expose to rain. Store indoors.

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.

• Read MSDS’s to know the specific hazards of the fluids you are using.

• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Always wear appropriate gloves, eye protection, and a respirator or mask when painting.

• Do not operate or spray near children. Keep children away from equipment at all times.

• Do not overreach or stand on an unstable support. Keep effective footing and balance at all times.

• Stay alert and watch what you are doing.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not kink or over-bend the hose.

• Do not expose the hose to temperatures or to pressures in excess of those specified by Graco.

• Do not use the hose as a strength member to pull or lift the equipment.

PRESSURIZED ALUMINUM PARTS HAZARD

Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in pressurized aluminum equipment. Such use can cause serious chemical reaction and equipment rupture, and result in death, serious injury, and property damage.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss. This equipment includes but is not limited to:

• Protective eyewear and hearing protection

• Gloves, clothing and respirator as recommended by the fluid and solvent manufacturer

313753G

Warnings

Grounding and Electric Requirements

This equipment requires a 240 Vac, 50 Hz, 15A circuit, with a grounding receptacle.

Do not alter the ground prong or use an adapter.

Sprayer

HVLP 7.0

HVLP 9.0

HVLP 9.5

Use 3-wire, 12 awg, 50 ft (15 m) or shorter, extension cords with ground prong.

Sprayer Components Table

Model

257829, 257833

257830, 257834

257831, 257835

Hose

30-ft

30-ft

30-ft and 4-ft

Gun

257827 EDGE

257827 EDGE

257827 EDGE

Fluid Sets

#3

#3, #4

#2, #3, #4

313753G 5

6

Component Identification

Component Identification

G

S

R

T C

E

L

M

U

N

A

B

H

A Sprayer air outlet

B

C

Sprayer power switch

Fluid storage compartment

D Sprayer handle

E

F

Power cord storage

Air filters (pre-filter and main)

G

H

J

Item

Spray gun

Air filter indicator

Connector and power cord

Description

HVLP connector for air supply to HVLP spray Gun

On/Off switch for sprayer motor

Provides storage for up to four fluid sets

Folds flat for minimum storage space

Provides storage for power cord

Provides filtered air for spray gun and motor

Graco EDGE

™ spray gun with EasyGlide

™ trigger

Lights when air filter needs to be cleaned or replaced

Provides power for sprayer

(power cord provided with sprayer)

F

P

D

K

J ti12854a

K

L

M

N

P

R Storage tray

S

T

Cleaning cup holder

EDGE spray gun holder

U

Item

Resettable circuit breaker

Quick connect

Air valve

Air hose

Hose wrap

Hose, 4-ft

Description

Provides protection for motor

Enables quick connection to spray gun

Provides HVLP 9.0 and 9.5 sprayers ability to shut off air to spray gun

Hose, 30 ft x 1 in., that connects spray gun and sprayer.

Provides storage for air hose when air hose is not in use

Provides extra storage

Provides storage for cleaning cup

Provides external storage for spray gun

Allows increased flexibility for the HVLP 9.5

313753G

Setup

Setup

Fluid Preparation

• Strain fluids before you spray. This includes color, reducers and hardeners.

• Use a slower drying reducer or thinner to compensate for the faster drying time caused by the warm air of the turbine. Do not over reduce

• Sprayer performance varies with the viscosity of the material sprayed and the length of the hose. To prevent pressure drop, use hose supplied with sprayer.

• Most material manufacturers provide recommendations for their materials. Follow these recommendations.

Connect Fluid and Air Supply

Spray Gun with Siphon Cup

1.

Connect air hose to sprayer.

Hand tighten.

Pressure Relief Procedure

The spray gun siphon cup is pressurized by the gun air supply. To reduce the risk of serious injury from pressurized fluid or accidental spray from gun, always turn off the air supply to the spray gun before removing the siphon cup.

1.

Turn off sprayer.

2.

Unplug sprayer.

3.

Unlatch cup cover; loosen or remove cup from cover to relieve pressure.

Operation Tips

ti13082a

2.

Connect air hose from sprayer to inlet fitting of gun.

Sparks can be expected during normal operation of motor. These sparks can ignite fumes from flammable liquids, dust particles, and other flammable substances in the spray area.

• Use additional hose if necessary, and ensure the sprayer is operated in clean, dry, well ventilated area.

• Never use sprayer inside spray booth.

3.

Fill cup 3/4 full. Install cover. Latch the gun cup cover to secure it to siphon cup. See HVLP EDGE Gun manual for operation instructions.

ti12797a ti12872a

Connect to Electric Supply

Plug sprayer power cord into grounded outlet. Grounding

and Electric Requirements, page 5.

• Turn sprayer on a few minutes before spraying to allow warm-up.

• Ensure sprayer filter is clean before operating. Clean

filter, page 8.

• To adjust spray gun pattern, see HVLP EDGE Gun manual.

• To get proper adhesion, ensure surface is completely clean.

• Always spray with the least amount of pressure required to provide the desired spray pattern and rate of application. Spraying at pressures higher than necessary wastes paint and can result in an orange peel finish.

313753G 7

8

Maintenance

Maintenance

The sprayer system is lifetime lubricated. The only maintenance required is filter cleaning and replacement.

Filter Operation

The sprayer filter must be clean at all times to provide sufficient air flow to cool the motor and atomize the fluid.

The sprayer has an air filter indicator light on the front panel. The indicator light illuminates if the filter is clogged or has low airflow.

• Tap filter gently on flat surface, dirty side down.

• Direct, compressed air (100 psi(7 bar, 70 MPa) maximum) through filter panel in the opposite direction of arrows on side of filter (from the clean side to the dirty side.

• Soak filter for 15 minutes in water and mild detergent. Rinse filter until clean. Air dry.

To avoid electric shock, never install a damp filter in the turbine. Installing a damp filter in sprayer can also damage turbine.

8049a

Cleaning Filter

1.

Turn off and unplug sprayer.

2.

Loosen four screws (18), remove filter retainer (17) and pre-filter (20).

3.

Remove main filter (21) and clean using one of the following methods:

21

20

17

18 ti13061a

313753G

Troubleshooting

Troubleshooting

Problem

No fluid delivery

Sprayer not starting

Poor atomization

Circuit breaker trips

Cause

No material, no remote cup pressurization, hose or pickup tube clogged

No power

Dirty filter

Extension cord too long

Hose too long

Filter clogged

High ambient temperature

Excessive current draw

Solution

Check cup for material

Check for leaks at the container gasket (1-quart remote cup cover).

Tighten cover if loose.

Check air flow (approximately 1/4

CFM) from male quick-disconnect at

Compact outlet.

Turn pressure regulator clockwise.

Look for pressure on gauge. (If no pressure on gauge, check air line fittings.)

Check hole in 1-quart remote cup cover at needle valve for blockage or dirt. Clean if necessary.

Check for obstructions.

Check if fluid pickup tube is loose.

Tighten.

Blow out and clear material hose.

Clean check valve. See manual.

Check outlet for power. Cycle red rocker switch.

Check that correct IEC (modular) cord is used and plugged in.

Check circuit breaker (38). Push to reset.

Clean filter and replace as necessary.

Extension cord must be 3-wire, 12

AWG, 50 ft (15 m) or shorter.

Replace with shorter hose. See

Graco Fine Finish Solutions brochure for hose part numbers.

Clean filter and replace as necessary

Move sprayer to cooler area.

Return to authorized service center.

313753G 9

Repair

Repair

Sprayer Disassembly

3.

Place sprayer upside down. Remove four screws (77) from sprayer base plate (2).

77

2

To avoid injury, including electric shock turn off sprayer and unplug power cord before performing any repair procedures on the turbine.

1.

Remove four thumbscrews (18) and remove filter retainer (17), prefilter (20) and main filter (16). Parts,

page 14.

ti12973a

4.

Pull up sprayer base plate and attached parts.

Thread motor wires that connected to inlet plug through access in HVLP box.

5.

Repair or replace any required parts.

18

16

20

17 ti13061a

2.

Remove two screws (45) and inlet plug (36) from

HVLP box (1). Remove four motor wire connectors from inlet plug (36).

36

45 ti13062a ti13063a

Sprayer Assembly

1.

Replace duct gaskets (59, 60) and any other damaged or worn parts. Replace circuit breaker (32), if it has cycled. Remove residual adhesive from previous gaskets by wiping any sticky surfaces with mineral spirits solvent (also called white spirit). Let solvent evaporate thoroughly before installing replacement gasket.

2.

Use an adjustable square with blade running full length of longest side of duct (22), to position duct perpendicular to the base (2). Hold duct in place to keep duct perpendicular to base edge and carefully remove square.

3.

Turn sprayer upside-down. Carefully slip base plate and attached parts down into HVLP box (1).

NOTE: Be sure duct to maintain duct alignment.

4.

Thread motor wires that connect with plug (61) through access port in HVLP box.

5.

Use four screws (77) to secure base plate to HVLP box (1). Use an adjustable clamp over the outside of

HVLP box (1) to align screw holes if necessary.

6.

Install three motor wire connectors onto plug (61).

Install plug (61) with two screws (101) into HVLP box

(1).

7.

Install filter gaskets (19), main filter (16) with arrow facing into HVLP box (1), pre-filter (20), filter retainer

(17), and hose rack (35) with four thumbscrews (18).

10 313753G

Turbine Replacement

Turbine Replacement

Refer to Parts Drawing, page 14.

1.

Follow Sprayer Disassembly procedure, page 10.

2.

Remove gasket (21).

3.

Remove three screws (14) from spacer (38).

4.

Remove plate (21) and three spacers (83).

5.

Remove motor wires from spade connectors.

6.

Rotate motor (11) from outlet fitting (29) and lift up from spacers (41).

7.

Install new gaskets (21, 23, 24, 59 and 60). Use mineral spirits solvent (also called white spirit) to remove any adhesive remaining from old gaskets.

8.

Reassemble turbine. Use an adjustable square with the blade running the full length of the longest side of the duct (22) to position duct perpendicular to base

(2). Hold duct in place and carefully remove square to keep duct perpendicular to edge of base. With sprayer upside down, carefully slip base plate and

attached parts (see page 16) down into HVLP box

(1). NOTE: Be sure to maintain duct alignment.

9.

Connect ground wire to motor housing.

10. Reconnect wires. Attach plug (61) to HVLP box with two screws (101).

313753G 11

Wiring Diagrams

Wiring Diagrams

110V

3 4

GROUND

12

G

W

BK

7

L

G

N

1

2

9

8

L

G

N

Ref. Part Description Qty.

6

7

4

5

1

2

3

244273 Conductor, BK

15W486 Conductor, BK

15W485 Conductor, G/Y

15W484 Conductor, W

257333 Conductor, W, BK, G

240256 Conductor, W

114064 Plug, inlet

8

9

114403 Circuit Breaker, 15A 1

15V923 Plug, outlet, CompPack 1

10 114280 Light, indicator, 120V

11 120660 Switch, rocker

12 114279 Sensor, pressure 1

1

1

1

1

1

1

1

1

1

6

240V

GROUND

15

8

6

7

3

16

3

6

2

5

G

BK

W

16

3

6

2

5

4

10

LG

LINE

G

L2

L1

LOAD

L2

14 9 ti12765a

5

10

L

G

N

1

2

11

12

5

L

G

N

Ref. Part Description Qty.

7

8

5

6

3

4

1

2

244273 Conductor, BK

15W486 Conductor, BK

15W485 Conductor, G/Y

15W484 Conductor, W

257333 Conductor, W, BK, G

15W488 Conductor, W

15W487 Conductor, BK

240558 Conductor, G/Y

9 240256 Conductor, W

10 114064 Plug, inlet

11 16A348 Circuit Breaker, 8A 1

12 15V923 Plug, outlet, CompPack 1

1

1

13 114286 Light, Indicator, 240V

14 120660 Switch, rocker

15 114279 Sensor, pressure

16 116168 Filter, suppression

1

1

1

1

1

1

1

1

1

1

1

1 ti12770a

13

12 313753G

Technical Data

120 Vac, 60 Hz

HVLP 7.0

HVLP 9.0

HVLP 9.5

Ampere Watts

11.0

200

11.0

13.6

250

300

Maximum

Hose Length ft (m)

40 (12,2)

60 (18,3)

60 (18,3)

Sprayer Weight lb (kg)

28 (12,7)

29 (13,2)

30 (13,6)

Total Weight lb (kg)

38 (17,2)

39 (17,7)

40 (18,1)

Sound

Power*

94.9 dBa

95.9 dBa

96.3 dBa

Technical Data

Sound

Pressure*

82 dBa

83 dBa

83.4 dBa

240 Vac, 50 Hz

HVLP 7.0

HVLP 9.0

HVLP 9.5

Ampere Watts

5,40 200

5,93

7,07

250

300

Maximum

Hose Length ft (m)

40 (12,2)

60 (18,3)

60 (18,3)

Sprayer Weight lb (kg)

28 (12,7)

29 (13,2)

30 (13,6)

Total Weight lb (kg)

38 (17,2)

39 (17,7)

40 (18,1)

Sound

Power*

94.9 dBa

95.9 dBa

96.3 dBa

Sound

Pressure*

82 dBa

83 dBa

83.4 dBa

* Sound Power and Sound Pressure are measured at

1 meter per ISO 3744

313753G 13

Parts

Models 257833, 257834, 257835, 257829, 257830, 257831

4

103

102

3

6 34 100

30

1

30

8

63

Parts

62

33

105

49

89

13

104

14

87

25

77

88

61 101

19

16

20

17

35

77

18

18 ti13855a

313753G

Parts List

Parts List

Models 257833, 257834, 257835, 257829, 257830, 257831

Ref.

Part

30

33

34

35

49

18

19

20

25

8

13

16

17

4

6

1

3

Description

277934 BOX, HVLP

24B055 COVER, HVLP, includes 6

15V791 HANDLE

15V771 LID, accessory

15V926 LATCH

257159 HOSE, air, 30 ft, black

240273 FILTER, main

15W794 RETAINER, filter

15W897 SCREW, captive

15W217 GASKET, filter

15W909 FILTER, foam

113817 BUMPER

15W505 SCREW, mach, phillips pan hd

256855 GUN, HVLP, with cup

114271 STRAP, retaining

15V862 HOSE, rack

VALVE, air control

HVLP 7.0 (not included)

240065 HVLP 9.0

240065 HVLP 9.5

Qty.

1

1

2

1

1

4

4

2

1

1

2

1

1

1

1

1

1

1

Ref.

Part Description

61 15V923 PLUG, inlet

62 ▲ 15W100 LABEL, safety

63

15W223 LABEL, safety

77 15W359 SCREW, mach, hex, washer hd

87

88

15W639 LABEL, Fine Finish

LABEL, HVLP

15W636 LABEL, HVLP 7.0

15W637 LABEL, HVLP 9.0

15W638 LABEL, HVLP 9.5

257161 HOSE, 4 ft, HVLP 9.5

89

100 15V927 HINGE

101 117317 SCREW, plastite, pan hd

102 15X227 SCREW, cap, hex hd

103 102040 NUT, lock, hex

104 116234 BOTTLE

105 M70402 QUICK DISCONNECT

2

2

2

2

1

1

1

1

1

1

Qty.

1

8

1

1

1

▲ Extra Danger and Warning labels are available for free.

313753G 15

Parts Drawing

Parts Drawing

Models 257833, 257834, 257835, 257829, 257830, 257831

14

21

15

11

29

38

9

109

107

108

16

30

86 106

48

41

59

39

22

60

42

44

37

24

5

31

90

2

64

45

36

45

46

58

110

32

27

28

45

14

23

56 ti12836d

313753G

Parts List

Parts List

Models 257833, 257834, 257835, 257829, 257830, 257831

Ref.

Part Description

2

5

9

11*

14

15

21

+

257066 PLATE, base, turbine, painted

114279 SENSOR, pressure

156698 O-RING

TURBINE

15Y812 HVLP 7.0, 3-stage, 120V

15Y813 HVLP 9.0, 4-stage, 120V

15Y814 HVLP 9.5, 5-stage, 120V

15Y815 HVLP 7.0, 3-stage, 240V

15Y816 HVLP 9.0, 4-stage, 240V

15Y817 HVLP 9.5, 5-stage, 240V

114670 SCREW, cap, hex hd

194094 PLATE, turbine

GASKET, turbine

15W153 HVLP 7.0

15W152 HVLP 9.0

192788 HVLP 9.5

22 15W274 DUCT, turbine

23 ◆✓ 16P954 GASKET, DUCT

24 192845 GASKET, DUCT

27 120660 SWITCH, rocker

28 LIGHT, indicator

114280 120V

114286 240V

15W272 FITTING, outlet 29

30

31

32 ◆✓

114669 SCREW, mach, phillips pan hd

193059 GASKET, sensor

CIRCUIT Breaker

114403 120V, 15A

36

37

38

39

41

16A348 240V, 8A

114064 PLUG, INLET

192905 PLATE, deflector

SPACER, turbine

15W148 HVLP 7.0

15W149 HVLP 9.0

15W150 HVLP 9.5

192810 HOSE, air

15X722 SPACER, turbine

Qty.

1

1

1

3

1

3

3

3

1

1

1

1

1

1

1

2

1

1

1

1

1

1

1

1

6

1

1

1

1

1

1

1

Ref.

Part Description

42

44

45

46

111593 SCREW, grounding

102063 WASHER, lock, ext

SCREW, mach, torx pan hd

15W998 120V

15W998 240V

CORD, power

15W126 USA, 6 ft. 15A, 120V

116281 Euro, 2 m, 8A, 240V

48 114287 FITTING, barbed

56 186620 LABEL, ground

58

15K616 LABEL, brand, hot surface

59 ◆✓ 16E351 GASKET, duct, left

60 ◆✓ 16E353 GASKET, duct, right

64 ▲ 15W224 LABEL, safety

86 15W640 LABEL, brand, TurboForce

90 114689 BUSHING, strain relief

106 116168 FILTER, suppression, EMI, 240V

107 242001 CORDSET, adapter, Europe

108 287121 CORDSET, adapter, 220V, global, includes 108a through 108d

108a CORDSET, adapter, Italy

108b

108c

CORDSET, adapter, Denmark

CORDSET, adapter, Switzerland

109 195551 RETAINER, plug adapter

110 15X254 SWITCH INDICATOR LABEL

Qty.

1

1

4

6

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

* Cleaning Brush Kits 256953 and 256954 are also available.

▲ Extra Danger and Warning labels are available for free.

+ Turbine kit includes items 9, 15, 21, 23, 24, 59 and 60

◆ Gasket/Breaker Kit 15 Amp 24F670 includes items 23,

32, 59, 60

✓ Gasket/Breaker Kit 10 Amp 24F671 includes items 23,

32, 59, 60

313753G 17

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by

Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.

This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO

WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE .

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy

(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY

GRACO . These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of

Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

ADDITIONAL WARRANTY COVERAGE

Graco does provide extended warranty and wear warranty for products described in the “Graco Contractor Equipment Warranty Program”.

Graco Information

For the latest information about Graco products, visit www.graco.com.

TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

For patent information, see www.graco.com/patents.

Original instructions.

This manual contains English. MM 313753

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2008, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com

Revised September 2012

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement