Graco 3A1244E System Manual


Add to my manuals
9 Pages

advertisement

Graco 3A1244E System Manual | Manualzz

GENUINE GRACO PARTS AND ACCESSORIES

Graco Control

Architecture

Module

Programming

3A1244E

EN

For updating or programming the software version of Graco Control Architecture Modules.

For professional use only.

See your system manual when replacing parts in hazardous locations.

Important Safety Instructions

Read all warnings and instructions in this manual and your system manuals. Save these instructions.

Advanced Fluid Control Module

USB Module

Display Module

Not all modules shown.

ti16440a

Supply Power to Module

2

To help prevent fire and explosion, do not connect, download, or remove the token unless the unit is removed from the hazardous (explosive atmosphere) location.

strap.

NOTICE

To avoid damaging circuit board, wear a grounding

• Use the token to load software to the Graco Control

Architecture Module before use. Follow all directions and warnings in this manual and your system repair/parts manual.

• Upgrade token part numbers can be found in the system manual.

NOTE: Install software on the primary display of the system. All software may be able to be updated from the display, depending on system software and module series. See system manual for availability of this feature.

• Upgrade all modules in the system to the software version on the token, even if you are replacing only one or two modules. Different software versions may not be compatible.

• All data in the module may be reset to factory

default settings. Record all settings and user preferences before the upgrade, for ease of restoring them following the upgrade.

• The latest software version for each system can be found at www.graco.com.

Supply Power to Module

Supply electrical power to the Graco Control Architecture module using either system power or Power Supply

Kit 24F672, available separately.

1.

Remove power from the Graco Control Architecture

Module by turning off system power or unplugging the Power Supply Kit 24F672 (available separately).

2.

Remove access cover (C).

NOTE: For cube modules, the cover is removed by pressing in the two tabs. For other modules, one or more screws (S) must be removed.

3.

Insert and press the token (T) firmly into the slot.

NOTE: Token has no preferred orientation.

4.

Supply electrical power to the Graco Control Architecture Module using either system power or Power

Supply Kit 24F672 (available separately).

NOTE: The Motor Control Module 257696, High Power

Temperature Control Module 255774, and the Low

Power Temperature Control Module 256270 do not require power to the high voltage AC input.

5.

The red indicator light (L) will flash while the software is being loaded. When the software is completely loaded, the red light will turn off.

NOTE: For the USB module only, when the red light stops flashing, the green and orange indicator lights adjacent to the USB connector will flash for several minutes while configurations are loaded. The software is completely loaded when the red, green, and orange indicator lights are off.

NOTE: For displays only: If is displayed on the

screen, see Remote Loading, page 3.

NOTICE

To prevent corrupting the software, do not remove the token, turn off the system power, or disconnect any modules until the status screen indicates that updates are complete.

Software Upgrade

Instructions

Follow these instructions to upgrade the software in all of the Graco Control Architecture Modules. Reference

illustrations of each module starting on page 6.

6.

Remove power from the Graco Control Architecture

Module by turning off system power or unplugging the Power Supply Kit 24F672.

7.

Remove the token (T) from the slot.

8.

Reinstall the access cover and secure with screws

(S), if applicable.

3A1244E

Remote Loading

9.

Upgrade all other modules in the system to the software revision on the token, if not already completed.

Different software versions may not be compatible.

NOTE: If the software on the token is the same version that is already programmed on the module, nothing will happen (including flashing red light). No harm can be done by attempting to program the module multiple times. For Communications Gateway Modules, installing upgrade software will not erase or overwrite a data map, if already loaded.

3.

Wait for update to complete.

NOTE: The approximate time until completion is shown along bottom of progress bar.

Remote Loading

Display on System

Advanced Module (ADM), 24E451

Display Module 262384, 24F493

Display Control Module, 24L096, or Advanced

Display Control Module, 24L097

Page

3

4

5

Systems With Advanced Display Module

(ADM), 24E451

1.

The following screen will be shown when the display turns on.

4.

Updates are complete. Icon indicates update success or failure. See Icon Table. Press to continue.

Communications with other modules established.

2.

Select which software is applied to each module when multiple software options exist. The following screen is not present in all systems. See system specific manual for more details. Press continue.

to

A

B C

Icon Description

Update successful

Update unsuccessful

Update complete; no change necessary.

Modules were updated or didn’t require an update; however, one or more modules need to be updated manually with a token.

3A1244E

Key:

A Module Serial Number

B Software currently on module

C Software available for module

3

Remote Loading

Systems With A Display Module,

262384, 24F493

1.

The following screen will be shown when the display turns on.

4.

Updates are complete. Icon indicates update success or failure. See Icon Table. Press continue.

to

Communications with other modules established.

2.

Select which software is applied to each module when multiple software options exist. The following screen is not present in all systems. See system specific manual for more details. Press continue.

to

A B C

Icon Description

Update successful

Update unsuccessful

Update complete; no change necessary.

Modules were updated or didn’t require an update; however, one or more modules need to be updated manually with a token.

Key:

A Module Serial Number

B Software currently on module

C Software available for module

3.

Wait for update to complete.

NOTE: The approximate time until completion is shown along bottom of progress bar.

4 3A1244E

Remote Loading

Systems With A Display Module or

Advanced Display Module, 24L096, 24L097

1.

The following screen will be shown when the display turns on.

4.

Updates are complete. Icon indicates update success or failure. See Icon Table. Press continue.

to

Communications with other modules established.

2.

Select which software is applied to each module when multiple software options exist. The following screen is not present in all systems. See system specific manual for more details. Press continue.

to

A

B

C

Icon Description

Update successful

Update unsuccessful

Update complete; no change necessary.

Modules were updated or didn’t require an update; however, one or more modules need to be updated manually with a token.

Key:

A Module Serial Number

B Software currently on module

C Software available for module

3.

Wait for update to complete.

NOTE: The approximate time until completion is shown along bottom of progress bar.

3A1244E 5

6

Available Graco Control Architecture Modules

Available Graco Control Architecture Modules

Display Module (262384, 24F493)

S

USB Module (289900)

L

C

C

T red light

Advanced Fluid Control Module

(255920)

T

Advanced Display Module

(24E451)

ti17215a

S

C

T

L ti17216a

L

S

C

T ti16439a

3A1244E

Available Graco Control Architecture Modules

Communications Gateway

Module (15V759, 15V760,

15V761, 15V762, 289835, 289836,

289837, 289838)

Fluid Control Module (289696)

L

L

C

C

T

Discrete Gateway Module

(24B681)

ti17217a

T ti17219a

Local Control Module (262416)

S

C

L

T

C

L ti17220a

T ti17218a

3A1244E 7

8

Available Graco Control Architecture Modules

High Power Temperature Control

Module (255774)

Motor Control Module (257396)

S

L

C

C

S

L

T ti17221a T ti17223a

Low Power Temperature Control

Module (256270)

Display Control Module (24L096) and Advanced Display Control

Module (24L097)

S

L

C

C

T ti17222a

T

L ti19597a

3A1244E

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by

Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED

TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy

(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT

MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

For the latest information about Graco products, visit www.graco.com

.

For patent information, see www.graco.com/patents .

TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.

Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions.

This manual contains English. MM 3A1244

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2010, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com

Revised November 2013

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • Programs and updates software on Graco Control Architecture Modules
  • Supports a wide range of modules, including display modules, USB modules, and fluid control modules
  • Easy-to-use interface and clear instructions for seamless operation
  • Provides a simple and efficient way to maintain and update Graco Control Architecture Modules
  • Compact and portable design for convenient use in various locations

Related manuals

Frequently Answers and Questions

What is the purpose of the Graco 3A1244F?
The Graco 3A1244F is used to program and update the software version of Graco Control Architecture Modules.
What types of modules are compatible with the Graco 3A1244F?
The Graco 3A1244F supports a wide range of Graco Control Architecture Modules, including display modules, USB modules, and fluid control modules.
How do I use the Graco 3A1244F?
The Graco 3A1244F comes with an easy-to-use interface and clear instructions that guide you through the programming and updating process.
What are the benefits of using the Graco 3A1244F?
The Graco 3A1244F provides a simple and efficient way to maintain and update Graco Control Architecture Modules, ensuring optimal performance and reliability.