Graco 307614E AIRLESS SPRAY GUN Owner's Manual

Add to my manuals
8 Pages

advertisement

Graco 307614E AIRLESS SPRAY GUN Owner's Manual | Manualzz

INSTRUCTIONS-PARTS

LIST

G?

O R I C O SUPERSEDES D

This manual contains IMPORTANT

WARNINGS and INSTRUCTIONS

READ AND RETAIN FOR REFERENCE

AIRLESS SPRAY GUN

361Mpsi (252 MAXIMUM WORKING PRESSURE

Model 220-955,

Series A

Includes RAC I V DripLessTM Tip Guard, 517 size

SwitchTipTM, and 2 finger trigger. Four finger trigger is optional. See parts list when ordering.

Model 217-593, Series C

Includes the Standard (non-reversing) DripCessTM Tip

Guard. Spray tip not included. Order Separately.

.....

.:

..,.

.,

.:

.~',.

....

.

..,,

Model 217-593

Warnings

IND EX

....................................

Installation

.....................................

.4

Operation

Service

....................................

..................................

Parts Drawing

How To Order b List

Replacement Parts..

Technical Data

Warranty

..........

.:...

2,

4,

..

3

5

.6

.........................

7

,Accessories

.......................

...................

Back Cover

..........................

Back Cover

Back Cover

.Back Cover

Model

220-955

Hazard of Using Fluids Containing Halogenated Hydrocarbons

Never use 1.1.1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in this equipment. Such use could result in a serious chemical reaction, with the possibility of explo- sion, which could cause death, serious bodily injuw andlor substantial property damage.

Consult your fluid suppliers to ensure that the fluids being used are compatible with aluminum and zinc parts.

GRACO INC. P.O. Box 1441 MINNEAPOLIS, MN 55440-1444

@COPYRIGHT 1 9 8 3 GRACO INC.

. . .

HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY.

FOR PROFESSIONAL USE ONLY. OBSERVE ALL WARNINGS.

Read and understand all instruction manuals before operating equipment.

FLUID INJECTION HAZARD

General Safety

Airless spray equipment generates very high fluid pressure.

Spray from the gun, leaks or ruptured Components can inject fluid through your skin and into your body and cause extreme- ly serious bodily injury, including the need for amputation.

Also, fluid injected or splashed into the eyes or onto the skin can cause serious damage.

Spray Tip Safety

Use extreme caution when cleaning or changing spray tips. If the spray tip clogs while spraying, engage the gun safety latch immediately. ALWAYS follow the Pressure Relief Pro- cedure. below. and then remove the spray tip to clean it.

NEVER point the spray gun at anyone or at any part of the body. NEVER put hand or fingers over the spray tip. NEVER try to "blow back" paint: this is NOT an air spray gun.

ALWAYS have the tip guard in place on the spray gun when spraying.

-

ALWAYS follow the Pressure Relief Procedure, t o the right, before cleaning or removing the spray tip.or servicing any system equipment.

.

,

NEVER try t o stop or deflect leaks with your hand or body.

NEVER wipe off build-up around the spray tip until pressure is fully relieved and the gun safety latch is engaged.

Pressure Relief Procedure

To reduce the risk of serious bodily injury, including fluid injec- tion: splashing in the eyes or on the skin; or injury from mov- ing parts, always follow this procedure whenever you shut off the spray equipment, when checking or servicing any part of the spray system, when installing, cleaning or changing spray tips, and whenever you stop spraying.

Be sure equipment safety devices are operating properly before each use.

Medical Alert-Airless Spray Wounds

If any fluid appears to penetrate your skin, get EMERGENCY

MEDICAL CARE A T ONCE. DO NOT TREAT A S A

SIMPLE CUT. Tell the doctor exactly what fluid was injected.

Note to Physician: injection in the skin is a traumatic in- jurf. It Is important t o treat the injury surgically es as possible. Do not delay soon treatment to research toxicity.

Toxicity is a concern with some exotic coatings injected directly into the blood srream. Consultation with a plasric surgeon or reconstructive hand surgeon may be advisable.

Spray G u n Safety Devices

Be sure all gun safety devices are operating properly before each use. Do not remove or modify any part of the gun; this can cause a malfunction and result in serious bodily injury.

1. Engage the gun safety latch.

2. Shut off the power supply to the pump and close any bleed-type master air valves in the air supply.

3. ,Disengage the gun safety latch.

4. Hold a metal part of the gun firmly to the side of a ground- ed metal pail, and trigger the gun into the pail to relieve oressure.

5. Engage the gun safety latch.

6. Open the pump fluid drain valve (required in the systeml, having a container ready to catch the drainage.

7. Leave the drain valve open until you are ready to spray again.

If you suspect that the spray tip or hose is completely clogged. or thet pressure has n o t been fully relieved after following the steps above, VERY SLOWLY loosen the tip guard retaining nut or hose end coupling and relieve pressure gradually, then loosen completely. Now clear the tip or hose.

EQUIPMENT MISUSE HAZARD

Safety L a t c h

Whenever you stop spraying, even for a moment, aiways engage the gun safety latch in the closed or ON SAFE posi- tion, making the gun inoperative. Failure to engage the s a f w latch can result in accidental triggering of the gun. See Fig 2,

page 4.

G e n e r a l Safety

Any misuse of the spray equipment or accessories, such as overpressurizing, modifying parts, using incompatible chemicals and fluids, or using worn or damaged parts, can cause them to rupture and result in fluid injection or other serious bodily injury, fire, explosion or property damage.

NEVER alter or modify any part of this equipment; doing could cause it to malfunction. so

Diffuser

The gun diffuser breaks up spray and reduces the risk of fluid injection when the tip is not installed. Check diffuser operation regularly. Follow the Pressure Relief Procedure, below, then remove the spray tip. Aim the gun into a grounded metal pail, holding the gun firmly to the pail. Using the lowest possi- ble pressure, trigger the gun. If the fluid emitted is not diffused into an irregular stream, replace the diffuser immediately.

Tip Guard

ALWAYS have the tip guard in place on the spray gun while spraying. The tip guard alerts you to the fluid injection. hazard and helps reduce, but does not prevent, the risk of accidental- ly placing your fingers or any part of your body close t o the spray tip.

Trigger Guard

NEVER operate the gun with the trigger guard removed. The trigger guard reduces the risk of accidentally triggering the gun if it is dropped or bumped.

CHECK all spray equipment regularly and repair or replace worn or damaged parts immediately.

Read and follow the fluid solvent manufacturer's literature regarding the use of protective clothing and equipment.

System Pressure

DO NOT exceed 3600 1252 bar/ MAXIMUM WORKING

PRESSURE to the gun. Be sure all accessory items and system components are rated to withstand the pressures developed. NEVER exceed the pressure rating of any compo- nent in the system.

Fluid Compatibility

BE SURE that a11 fluids and solvents used are chemically com-

Datible with the wetted Darts shown in the Technical Data on the back cover. Always read the manufacturer's literature before using a fluid or solvent in the system.

2

307-614

!

..

Static electricity is created by the high velocity flow of fluid through the pump and hose. If every part of the spray equip- ment is not properly grounded, sparking may occur, and the system may become hazardous. Sparking may also occur when plugging in or unplugging a power supply cord. Sparks can ignite fumes from solvents and the fluid being sprayed, dust particles and other flammable substances. whether you are,spraying indoom or outdoom, and can cause a fire or ex- plosion and serious bodily injury and property damage. Do not plug in or unplug any power supply cords in the spray area when there is any chance of igniting fumes still in the air.

If you experience any static sparking or even a slight shock while using this equipment, STOP SPRAYING IM-

MEDIATELY. Check the entire system for proper grounding.

Do not use the system again until the problem has been iden- tified and corrected.

G r o u n d i n g

To reduce the risk of static sparking, ,ground all the spray equipment used or located in the spray area. CHECK your local electrical code end your equipment's individual instruc- tion manuals for detailed grounding instructions for.your area and type of equipment and be sure to ground all of this spray equipment:

1. Pump or sprayer: as instructed in your separate pump or sprayer manual.

2. Air compressor or hydraulic power supply: according t o local code.

HOSE SAFETY

High pressure fluid in the hoses can be very dangerous. If the hose develops a leak, split or rupture due to any kind of wear, damage or misuse, the high pressure spray emitted from it can cause a fluid injection injury or other serious bodily injury or propelty damage.

ALL FLUID HOSES MUST HAVE SPRING GUARDS ON

BOTH ENDS1 The spring guards help protect the hose from kinks or bends at or close t o the coupling which can result in hose rupture.

TIGHTEN all fluid connections securely before each use. High pressure fluid can dislodge a loose coupling or allow high pressure spray to be emitted from the coupling.

NEVER Ose a damaged hose. Before each use, check the en- tire hose for cuts, leaks, abrasion, bulging cover. or damage or movement of the hose couplings. If any of these conditions exist, replace the hose immediately, DO NOT try t o recouple high pressure hose or mend it with tape or any other device. repaired hose cannot contain the high pressure fluid,

A

MOVING PARTS HAZARD

Moving parts can pinch or amputate your fingers or other body parts.

KEEP CLEAR of moving parts when starting or operating your system. Disconnect the power source and relieve pressure by following the Pressure Relief Procedure

on page 2

before checking or servicing your system to prevent the pump from cycling accidentally.

3. Fluid hoses: use onty grounded hoses with a maximum of

500 feet 1150 m) combined hose length t o ensure ground- ing continuity. Refer to Hose Grounding Continuity. below.

4. Spray gun: obtain grounding through connection to a properly grounded fluid hose and sprayer or pump.

5. Fluid supply container: according to local code.

6. Object being sprayed: according t o local code

7. All solvent pails used when flushing, according to local code. Use only metalpails, which are conductive. Do not place the pail on a non-conductive surface, such as paper or cardboard, which interrupts the grounding continuity.

8. To maintain grounding continuity when flushing or reliev- ingpressure, always hold a metal part of the gun firmly t o the side of a metal pail, then trigger the gun.

F l u s h i n g S a f e t y

Before flushing, be sure the entire system and flushing pails are properiy grounded. Refer to Grounding. above. Follow the Pressure Relief Procedure on page 2, and remove the spray tip from the gun. Always use the lowest possible fluid pressure. and maintain firm metal-to-metal contact between the gun and a grounded metal pail during flushing to reduce the risk of a fluid injection injury, static sparking and splashing.

HANDLE AND ROUTE HOSES CAREFULLY. Do not pull on hoses t o move equipment. Do not use fluids or solvents which are not compatible with the inner tube and cover of the hose.

DO NOT expose Graco hose to temperatures above l W 0 F

182°C) or below 40°F l-40°C).

Hose G r o u n d i n g C o n t i n u i t y

Proper hose grounding continuity is essential to maintaining a grounded spray system. Check the electrical resistance of your air and fluid hoses a t least once a week. If your hose does not have a tag on it which specifies the maximum electrical resistance, contact the hose supplier or manufacturer for the maximum resistance limits. Use a resistance meter in the ap- propriate range for your hose to check the resistance. If the resistance exceeds the recommended limits, replace it im- mediately. An ungrounded or poorly grounded hose can make your system hazardous. Also read FIRE OR EXPLOSION

HAZARD. above.

TERMS

W A R N I N G : Alerts user to avoid or correct conditions that could cause bodily injury.

CAUTION: Alerts user to avoid or correct conditions that could damage the equipment.

NOTE: Gives special procedures or information.

IMPORTANT

United States Government safety standards have been adopted under the Occupational Safety and Health Act. These standards-par- ticularly the General Standards, Part 1910, and the Construction Standards, Part 1928-should be consulted.

307-614 3

~~~~~

INSTALLATION

NOTE:

Numbers and letters in parentheses in the text corresoond to the reference numbers

~~ and letters-[n the drawings and parts list.

I-

WARNING

Be sure your system has a bleed-type master air valve (pneumatic pumps only) and a fluid drain valve. These two accessories help reduce the risk of serious bodily injury, including fluid injection. splashing in the eyes or on the skin, or injury from moving parts, if you are adjusting or repairing the pump or gun.

1. The bleed-type master air valve relieves air trap- ped between this valve and the pump after the air regulator is shut off. Trapped air can cause the pump to cycle unexpectedly.

-

2. The fluid drain valve assists in relieving fluid pressure in the displacement pump, hose and gun; triggering the gun to relieve pressure may not be sufficient. J

1

.

Connect a grounded fluid hose to the gun inlet.

2. With no tip installed, start the pumplsprayer. Flush it according to the instructions supplied with it.

Prime the system with the fluid you are using.

3.

Foilow the Pressure Relief Procedure on page 2.

4. Model217-593: with the gun safety latch engaged, unscrew the tip guard (31 and install the tip (B) and gasket (2) in the nut of the tip guard. Screw the assembly firmly onto the gun. Tighten with a wrench. See Fig 1.

OPERATION

WARNING

To reduce the risk of serious bodily injury, in- cluding fluid injection or splashing in the eyes or on the skin, always follow the Pressure Relief Pro-

cedure on page 2

before checking, servicing. in- stalling, removing, changing or cleaning spray tips or any part of the gun or system.

Whenever you stop spraying for a moment, engage the gun safety latch. See Fig 2.

WARNING

gun should be kept with the operator at all times.

The card contains important treatment information should an injection injury occur. Additional cards

Flg 1

NOTE:

Failure to install the tip gasket (2) will result in leaking.

5. Model220-955: with the un safety latch en a ed, install 'the SwitchTiDTM. lefer to manual supplied.

387-848.

6. Strain the fluid vou are sDravina if it contains oar- t i c k which couid clog the sprai tip.

3. Use a full-open, full-close trigger action. Hold the gun about 14 in. (350 mm) from and a t right angles to the work surface. Don't swing the gun in an arc.

Practice to find the best length and speed of stroke.

1. Start the pump. Adjust the fluid pressure so the spray is completely atomized. Always use the lowest pressure necessary to get the desired results.

Higher pressure may not improve the spray pattern and will cause premature tip and pump wear.

2. If adjusting the pressure does not give a good spray pattern, try another tip size. Be sure to relieve pressure completely before changing tips.

TO DISENGAGE SAFEpl

LATCH IOFFSAFEITURN

LATCH PARALLELTO

BODY

4

307-614

Adjust t h e Spray Pattern

1 . To adjust the spray pattern direction, follow the

Pressure Relief Procedure on page 2.

Engage the safety latch and loosen the tip guard retaining nut.

Turn the tip guardltip groove so it is horizontal for a horizontal spray pattern, and vertical for a vertical pattern. Tighten the nut.

2. The spray tip orifice size and spray angle determines the coverage and size of pattern. When more coverage is needed, use a larger spray tip rather than increasing fluid pressure.

WARNING

of a fluid injection injury,

NEVER use the gun with the tip guard or trigger w a r d removed.

I

Openings in the tip guard are designed to reduce paint buildup on the guard while spraying. Any damage to the sharp edges of the openings causes paint to collect at that area. To reduce the risk of

C A U T ' O N 1

Cleaning and Clearing the Spray Tip

WARNING

To reduce the risk of a fluid injection or splashing in the eyes or on the skin, DO NOT hold your hand, body, or a rag in front of the spray tip when cleaning or checking a clogged tip. Always point the gun toward the ground or into a waste con- tainer when checking to see if the spray tip is cleared.

DO NOT try to "blow back" pa.int; this is NOT an air spray gun.

DO NOT wipe fluid buildup off the gun or spray tip until pressure is relieved. See the Pressure Relief

Procedure Warning on page 2.

Clean off the front of the tip frequently during the day's operation and a t the end of the work day. Always follow

the Pressure Relief Procedure Warning on page 2.

Then use a 'solvent soaked brush to clean the spray tip and to keep fluid buildup from drying and clogging the spray tip.

If the spray tip clogs while spraying, release the spray gun trigger, engage the trigger safety, shut off the pump, and follow the Pressure Relief Procedure

Warning on page 2.

Then proceed for your gun model:

Model 217-593: Remove the spray tip and blow out the obstructions with air from the front of the spray tip, or let the spray tip and gun nozzle soak long enough to dissolve the obstruction. If it won't dissolve, jar it out by tapping the back of the spray tip against.a flat surface.

Model 220-955: information on clearing a clog and cleaning the spray tip.

CAUTION

N N E R soak the entire gun in solvent. Prolonged exposure to solvent can ruin the packings.

Cleaning the Filter 117) See

Fig 3.

Normal daily flushing of your spray system and gun flushes away most buildup on the filter. However, ,you should remove the filter weekly and clean it.

Fig 3

1. Remove the screw (14) from the trigger guard retainer (13).

2. Push up on the trigger guard (12) and swing it away from the trigger (5).

3. Unscrew the gun handle from the fluid housing (261 and remove the filter. Clean the filter in compatible solvent.

4. Apply lithium-base grease t o the threads of the fluid tube (191, and reassemble the gun.

. . . ushing the Gun

WARNING

Before flushing, be sure the entire system and flushing pails are properly grounded. Refer to

Grounding, on page 3.

Follow the Pressure

Relief Procedure on page 2, and remove the spray tip from the gun. Always use the lowest possible fluid pressure, and maintain firm metal t o metal contact between the gun and the pail during flushing to reduce the risk of a fluid injection in- jury, static sparking and splashing.

Relieve pressure, remove the spray tip, and then flush the gun and spray system with a compatible solvent.

Always flush the gun before the fluid being sprayed can dry in it.

~.

MAINTAIN F

METAL TO ME

CONTACT BETWEEN

GUN AND CONTAINER

SERVICE

WARNING

cluding fluid injection, splashing in the eyes or on the skin, or injury from moving parts or electric shock, always follow the Pressure Relief Pro- cedure

Warning on page 2

before continuing.

NOTE:

A repair kit, part no. 218-070, is available for repairing the gun. Use all new parts in the kit for the best results.

Parts included in the kit are shown with two asterisks, for example (30'").

Disassembly (See Parts Drawing, page 7)

1. Remove the tip guard (3). tip (B), and gasket (2).

2. Squeeze the trigger while unscrewing the dif- fuserlseat (1) and gasket (38).

3. Remove the locknut (25) and end cap (23).

4. Tap the rear of the gun with a plastic mallet to push the needle assembly out the front.

5. Unscrew the ball and housing (35) from the fluid needle (24). Remove the spring (34). gland (30). packing (29). O-ring (28). and washer (27).

6. Soak the parts in clean, compatible solvent. Wipe clean. Inspect for wear or damage and replace parts as needed.

Reassembly (See Parts Drawing, page 7)

1. Grease the O-ring (28") with lithium-based grease and install it in the groove of the packing (29'9.

2. Install the washer (27**), bly, gland (30") with stem facing small end of nee- de, and the spring (34") on the needle (24").

3. Screw on the ball and housing (35'") lightly, torqu- ing only to 8-10 in-lb (0.9-1.1 N d .

4. Guide the threaded end of the needle assembly into the front of the gun.

5. Install the end cap, aligning its guides with the holes in the rear of the gun. Install the locknut (25) loosely.

6. Squeeze the trigger while installing the gasket

(38"') and diffuserhat (1). Torque the diffuser seat to 20-25 ft-lb (27-34 N m ) .

TO F

7. If the gun handle (6) it hand tight into the fluid housing (26). Loosen the setscrew (4). align the handle with the fluid housing, and torque the setscrew to 80-90 in-lb 19-10 N m l .

8. Adjust the needle before using the gun. See Ad- justing t h e Needle.

9. Be sure the trigger guard and tip guard are installed before using the gun.

Adjusting the Needle (See Fig 5)

WARNING

Proper adjustment of the needle is essential to be sure the trigger safety latch makes the gun in- operative when engaged. Improper adjustment may allow the gun to be triggered, even with the trigger safety latch engaged, resulting in serious bodily injury, including fluid injection and splashing in the eyes or on the skin.

1. Engage the gun safety latch.

2. Hold the gun with the nozzle straight up so the trig- ger falls onto the safety latch.

NOTE:

If the trigger does not touch the latch. turn the locknut (25) clockwise until it does.

3. With light pressure, hold the trigger against the latch. Turn the locknut (25) clockwise until there is enough tension for you to feel and see the trigger raise slightly off the latch.

4. Now turn the adjusting nut 314 turn counterclock- wise. ' .

.

5. Connect the hose. Install the tip guard and prime the system. Trigger the gun and release it. The fluid flow should stop immediately. Now engage the safety latch and try to trigger the gun. No fluid should flow.

If the gun fails either test, relieve pressure, discon- nect the hose and readjust the needle.

CLOCKWISE

6

307414

~

PARTS DRAWING

Gun Repair Kit 218-070

(Must b e purchased separately1

REF NO. a n

REF N O . a n

"13

27

28

1

1

35

38

"

PARTS LIST

Model 220-955. Series A

Includes items 1, 2, 4 t o 41

REF PART

NO. NO.

DESCRIPTION QTY

10

11

12

13

14

15

16

17

18

18a

19

20

21

1

2

3

4

5

5a

6

*'218-023 DIFFUSER/SEAT

*166-969 GASKET, tip

220-251 .TIP GUARD

100421 SETSCREW, soc hd cup pt;

-.

.-

.-

.. ?IF!'*

-.I

179-734 TRIGGER, 2 finger (standard)

179-943 TRIGGER, 4 finger (optional)

218-643 GUN HANDLE ASSEMBLY

~ ~~ t 172-479 t179-761

179-724

179-730

101-666

218-021

179-750

*218-131

'218-133

179-731

179-732

179-721

179-763

179-722

includes replaceable items 4.13 b14

TAG, instruction

", warninn

~

GUARD, trigger

RETAINER, guard

SCREW, thread forming type "F";

8-32 x 5 / 1 6

SWIVEL, gun

RETAINER, spring

FLUID FILTER ASSEMBLY

(standard 50 mesh) includes replaceable items 16, 18, 20 b 21

FLUID FILTER ASSEMBLY

(optional 100 mesh) includes

replaceable items 16, 18a 20 b 21a

ELEMENT, strainer. (standard 5Q mesh)

ELEMENT, strainer, (optional

TUBE, fluid

SPRING, compression

100 mesh)

RETAINER, spring (color coded blue).(for standard 60 mesh filter)

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

Model 217-593. Series C

Includes items 1 to 39

REF PART

NO. NO.

DESCRIPTION

21 a 179-957

22

23

'179-733

179-720

24 '*218-022

25 '"107-110

26 179-718

27 "179-762

28 '"103-185

29 "177-222

39 "177-223

31 105334

32 177-538

33 179-737

34 **107-109

35 *'218-024

37 179-729

38 "156766

39 t179-960

40 *221-517

41 2 -

RETAINER, spring (color coded

orangel,lfor optional 100 mesh filter)

GASKET, sleeve

CAP. end

NEEDLE,fluid

LOCKNUT: no. 10-32 thread

HOUSING, fluid

:'?+'

WASHER, backup

O-RING; polyurethane

PACKING, needle

GLAND

LOCKNUT; M4 x 0.7 thread

STUD, trigger

PIN, actuator

SPRING, compression

BALL b HOUSING

HOUSING, needle

GASKET, copper

CARD, warning

SPRAY TIP; 517 SwitchTipTM

RAC IV Dripless" Tip Guard

See 307-848, supplied

QN

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

*Recommended "tool box" spare parts. Keep on hand to reduce down time.

'"Supplied in repair kil218-070. tExtra warning tags and cards are supplied at no charge.

307-614 7

:.:.

ACCESSORIES

(Must be purchased s e p a r a t e l y ) .

IN:LINE FILTER 210-742

5odo psi 1350 barl M A X I M U M WORKING PRESSURE

60 mesh

(250 m i c r o n ) screen, standard replacement screen for 210-742.

210-731 Includes three 60 mesh 1250 m i c r o n ) screens

210-732 Includes three 100 mesh (149 m i c r o n ) screens

210-733 Includes three 200 mesh ( 7 4 m i c r o n ) screens

SWIVELS

Use for more flexible gun movement.

207-946 112 n D s m ( f ) x 318 n d f )

5ooo psi 1350 bar) h a x . Working Pressure

204-940.1 I 4 npt x 114 npsm

3oW psi (210 barl Max. Working Pressure

IN-LINE FILTER 210-500

3oW psi (210 bar) M A X I M U M WORKING PRESSURE

Installs between gun and hose.

NYLON BRUSHES

101-891 0.375" m m ) dia.

101-892 0.625"

( 1 6 m m ) dia.

WRENCH 171-147

TECHNICAL DATA

Maximum working pressure : 3600 psi (252 bar)

Fluid orifice : 0.125 in. (3.18 mrnl

Wetted parts : Stainless Steel, Aluminum,

Tungsten Carbide, Copper,

Weight

Inlet

Polyurethane, Polyethylene,

:

Nylon

M o z . 1135gl

: 114 npsmlm) swivel

SERVICE I N F O R M A T I O N

Listed below by the assembly changed are the OLD,

NEW and ADDED parts.

ASSEMBLY PART REF PART

Gun t o

Series C

NEW

ADDED

3 212-033 Guard

3 220-251 Guard

39 179-960 Card

NEW PRODUCT NOTE: Gun Model 220-955 has been added to this manual.

HOW

TO

ORDER REPLACEMENT PARTS

1. To be sure you receive the correct replacement parts, kit or accessories, always give all of the information requested in the chart below.

2. Check the parts list to identify the correct part number; do not use the ref. no. when ordering.

3. Order all parts from your near& Graco distributor.

6 digit

PART

NUMBER

I

QTY

I

PART DESCRIPTION

THE GRACO WARRANTY AND DISCLAIMERS

WARRANTY

Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. As purchaser's sole remedy for breach of this warranty, Graco will, for a period of twelve months from the date of sale. repair or replace any part of the equipment provan defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco's written recommendations.

This warrantydoes not cover, and Graco shall not be liable for, any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadaquata or improper maintenance, negligence, accident. tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility with Graco equipment of structures, accessories, equip- ment or materials not supplied by Graco. or the improper design, manufacture, installation, operation or maintenance of structures, ac- cessories. equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective for examination by Graco to vsrify the claimed defect. If tha claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to tha

Original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship. repairs will be made at a reasonable charge, which charges may include the the costs of parts, labor and transportation. i

I

I

. ..

.

. .

,.

.

. .

EQUIPMENT NOT COVERED BY GRACO WARRANTY

GRACO MAKES NO WARRANTY. AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR-

TICULAR PURPOSE, WITH RESPECT TO ACCESSORIES, EOUIPMENT, MATERIALS, OR COMPONENTS SOLD BUT NOT MANUFAC-

TURED BY GRACO. These items sold, but not manufactured by Graco [such as electric motor, switches, hose, etc.1. are subject to the warran- iv. if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

Factory Branche6:Atianta. Dallas. Detroit. Los Angelas. West Caldwell 1N.J.l

Subsidiary and Affilite Companie8:Canads; England: Switzerland; France; Germany; Hong Kong; Japan

GRACO INC. P. 0. Box 1441 MINNEAPOLIS, MN 55440-1444

PRINTED IN U S A . a7-614 583 Rwbd 347

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement