Graco 306706M STATIONARY AIRLESS PAINT SPRAYER 30:1 President Hydra-Spray Owner's Manual

Add to my manuals
12 Pages

advertisement

Graco 306706M STATIONARY AIRLESS PAINT SPRAYER 30:1 President Hydra-Spray Owner's Manual | Manualzz

INSTRUCTIONS-PARTS LIST

This manual contains important warnings and information.

READ AND KEEP FOR REFERENCE.

INSTRUCTIONS

306–706

Rev. M

Supersedes H

(includes Rev. J, K, and L)

STATIONARY AIRLESS PAINT SPRAYER

30:1 President Hydra-Spray

3000 psi (210 bar) Maximum Working Pressure

100 psi (7 bar) Maximum Air Input Pressure

Model 231–063

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

COPYRIGHT 1984, GRACO INC.

Graco Inc. is registered to I.S. EN ISO 9001

Table of Contents

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Positioning the Unit . . . . . . . . . . . . . . . . . . . . . . . . . .

System Accessories . . . . . . . . . . . . . . . . . . . . . . . . .

Connecting the Unit and Accessories . . . . . . . . . .

Operation/Maintenance

Pressure Relief Procedure

Flushing the Pump

. . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . .

2

7

7

5

6

5

5

Adjusting the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . .

Starting and Adjusting the Pump

Shutdown and Care of the Pump

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

Technical Data

Parts Drawing

Parts List

Warranty

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Graco Phone Numbers . . . . . . . . . . . . . . . . . . . . . . . . .

9

10

11

12

12

7

8

8

Symbols

Warning Symbol

WARNING his symbol alerts you to the possibility of serious injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the instructions.

WARNING

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

INSTRUCTIONS

D This equipment is for professional use only.

D Read all instruction manuals, tags, and labels before operating the equipment.

D Use the equipment only for its intended purpose. If you are not sure, call Graco Technical

Assistance at 1–800–543–0339.

D Do not alter or modify this equipment.

D Check equipment daily. Repair or replace worn or damaged parts immediately.

D Do not exceed the maximum working pressure of the lowest rated system component. See

Technical Data on page 9 for the maximum working pressure of this equipment.

D Use fluids and solvents that are compatible with the equipment wetted parts. Refer to the

Technical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

D Do not use hoses to pull equipment.

D Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose

Graco hoses to temperatures above 180 _ F (82 _ C) or below –40 _ F (–40 _ C).

D Wear hearing protection when operating this equipment.

D Do not lift pressurized equipment.

D Comply with all applicable local, state, and national fire, electrical, and safety regulations.

WARNING

INJECTION HAZARD

Spray from the gun, leaks, or ruptured components can inject fluid into your body and cause extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also cause serious injury.

Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate medical attention.

Do not point the gun at anyone or at any part of the body.

Do not put your hand or fingers over the spray tip.

Do not stop or deflect leaks with your hand, body, glove or rag.

Do not “blow back” fluid; this is not an air spray system.

Always have the tip guard and the trigger guard on the gun when spraying.

Check the gun diffuser operation weekly. Refer to the gun manual.

Be sure the gun trigger safety operates before spraying.

Lock the gun trigger safety when you stop spraying.

Follow the Pressure Relief Procedure on page 7 if the spray tip clogs and before cleaning, checking, or servicing the equipment.

Tighten all fluid connections before operating the equipment.

Check the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. Do not repair high pressure couplings; you must replace the entire hose.

Fluid hoses must have spring guards on both ends to help protect them from rupture caused by kinks or bends near the couplings.

MOVING PARTS HAZARD

The air motor piston can pinch or amputate your fingers.

The rotating blades of the agitator can pinch or amputate your fingers or other body parts and can cause splashing in the eyes or on the skin.

Always shut off the agitator and disconnect the air line before adjusting the angle of the agitator, removing the agitator from the drum, or checking or repairing any part of the agitator.

Keep clear of all moving parts when starting or operating the equipment.

Before servicing the equipment, follow the Pressure Relief Procedure on page 7 to prevent the equipment from starting unexpectedly.

WARNING

FIRE AND EXPLOSION HAZARD

Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result in a fire or explosion and serious injury.

Ground the equipment and the object being sprayed. Refer to Grounding on page 5.

If there is any static sparking or you feel an electric shock while using this equipment, stop spraying immediately.

Do not use the equipment until you identify and correct the problem.

Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid being sprayed.

Keep the spray area free of debris, including solvent, rags, and gasoline.

Electrically disconnect all equipment in the spray area.

Extinguish all open flames or pilot lights in the spray area.

Do not smoke in the spray area.

Do not turn on or off any light switches in the spray area while operating or if fumes are present.

Do not operate a gasoline engine in the spray area.

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin, inhaled, or swallowed.

Know the specific hazards of the fluid you are using.

Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local, state and national guidelines.

Always wear protective eyewear, gloves, clothing, and respirator as recommended by the fluid and solvent manufacturer.

4 306-706

Installation

NOTES:

Reference numbers and letters in parentheses in the text refer to the callouts in the figures and the parts drawing.

Accessories are available from your Graco representative. If you supply your own accessories, be sure they are adequately sized and pressure-rated to meet the system’s requirements.

Grounding

Proper grounding is an essential part of maintaining a safe system.

To reduce the risk of static sparking, the mounting cover and all electrically conductive objects or devices in the spray area must be properly grounded. Check your local electrical code for detailed grounding instructions for your area and type of equipment.

Object being sprayed: Follow your local code.

Fluid supply container: Follow your local code.

Solvent pails used when flushing: Follow your local code. Use only metal pails, which are conductive, placed on a grounded surface. Do not place the pail on a nonconductive surface, such as paper or cardboard, which interrupts the grounding continuity.

To maintain proper grounding continuity when flushing or relieving pressure, always hold the metal part of the spray gun firmly to the side of a grounded metal pail, then trigger the gun.

Positioning the Unit

Select a convenient location for the unit. The air valves for the pump (37), agitator (5), and elevator

(3) must be fully accessible.

For a ground wire and clamp, order

Part No. 237–569.

Agitator and drum cover: Connect one end of the ground wire (A) to the ground connector (B) on the rim of the drum cover. See Fig. 1. Connect the other end of the ground wire to a true earth ground. See the pump instruction manual (306–981) for instructions on grounding the pump.

The elevator needs 9 ft (2.8 m) of overhead clearance. Bolt the elevator to the floor as shown in the elevator instruction manual 306–287.

System Accessories

WARNING

A bleed-type master air valve (A) and a fluid drain valve (M) are required in your system. These accessories help reduce the risk of serious injury, including fluid injection and splashing of fluid in the eyes or on the skin, and injury from moving parts if you are adjusting or repairing the pump or agitator.

Fig. 1

B

A

Air and fluid hoses: Use only grounded hoses with 500 ft (150 m) maximum combined hose length to ensure grounding continuity.

Air compressor: Follow manufacturer’s recommendations.

Spray gun or dispensing valve: Connect to a properly grounded fluid hose and pump.

The bleed-type master air valve relieves air trapped between this valve and the pump after the air is shut off. Trapped air can cause the pump to cycle unexpectedly. Locate the valve close to the pump. Order Part No. 107–141.

The fluid drain valve assists in relieving fluid pressure in the displacement pump, hose, and gun. Triggering the gun to relieve pressure may not be sufficient. Order Part No. 210–658.

306-706 5

Installation

The installation shown in Fig. 2 is only a guide for selecting and installing system components and accessories.

Contact your Graco representative or Graco Technical Assistance (1–800–543–0339) for assistance in designing a system to suit your particular needs.

Connecting the Unit and Accessories

Ground the unit as described in Grounding on page 5.

Connect a 1/2 in. (13 mm) minimum ID, grounded air supply hose to the 1/2 in. npt(f) air inlet swivel (32).

The main air supply must include a bleed-type master air valve (A) for shutting off air pressure to the unit.

The fluid line must include a fluid drain valve (not shown), which helps relieve fluid pressure in the hose and gun.

You should install an air line filter (B) to remove dirt and moisture from the air supply.

To order an air line filter, order by Part No. from the list below:

203–421 1/2” npt inlet and outlet, with gauge,

200 psi maximum working pressure

See instruction manual 306–393.

204–856 1/2” npt inlet and outlet, without gauge,

200 psi maximum working pressure

See instruction manual 306–393.

Downstream from the air filter, you should install an air line lubricator (C) for automatic air motor lubrication. To order a 1/2” npt(f) inlet and outlet,

250 psi maximum working pressure airline lubricator, order Part No. 214–848. For more information, see instruction manual 307–316.

Connect the fluid hose (7) to the nipple on the outlet filter (17). Do not use thread sealer.

Connect the spray gun (20) to the swivel (5). See page 10.

B A elevator

32 C pump agitator

DETAIL A

See DETAIL A

Fig. 2

05511

NOTE: Valve feet must contact perforated plate.

04280

Operation/Maintenance

Pressure Relief Procedure

contaminated by the oil, flush it out with a compatible solvent.

WARNING

INJECTION HAZARD

The system pressure must be manually relieved to prevent the system from starting or spraying accidentally. Fluid under high pressure can be injected through the skin and cause serious injury. To reduce the risk of an injury from injection, splashing fluid, or moving parts, follow the Pressure Relief Procedure whenever you are instructed to relieve the pressure stop spraying check or service any of the system equipment install or clean the spray tips

1. Lock the gun trigger safety.

2. Shut off the air supply to the pump.

3. Close the bleed-type master air valve (required in your system).

4. Unlock the gun trigger safety.

5. Hold a metal part of the gun firmly to the side of a grounded metal pail, and trigger the gun to relieve pressure.

6. Lock the gun trigger safety.

7. Open the drain valve (required in your system), and have a container ready to catch the drainage.

8. Leave the drain valve open until you are ready to spray again.

If you suspect that the spray tip or hose is completely clogged, or that pressure has not been fully relieved after following the steps above, very slowly loosen the tip guard retaining nut or hose end coupling and relieve the pressure gradually. Then loosen it completely.

Then clear the tip or hose.

Flushing the Pump

WARNING

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the

Pressure Relief Procedure at left.

To flush the pump, do the following procedure:

1.

Relieve the pressure.

2. Remove the spray tip from the gun.

3. Hold a metal part of the gun firmly to the side of a grounded metal pail.

4. Start the pump. Always use the lowest possible fluid pressure when flushing.

5. Trigger the gun.

6. Flush the system until clear solvent flows from the gun.

7.

Relieve the pressure.

CAUTION

Never leave water or water-based fluid in the pump overnight. First, flush with water or a compatible solvent, then with mineral spirits. Relieve the pressure, but leave the mineral spirits in the pump to protect the parts from corrosion.

Adjusting the Unit

You must adjust the elevator to ensure that the cover is supported by the drum.

CAUTION

Shortened or recycled drums may cause the pump or agitator to bottom out in the drum, causing damage. Contact your fluid supplier to order a standard size drum.

WARNING

FIRE AND EXPLOSION HAZARD

Before flushing, read the section FIRE

OR EXPLOSION HAZARD on page 4.

Be sure the entire system and flushing pails are properly grounded. Refer to

Grounding on page 5.

Flush the pump before first use. The pump is tested with lightweight oil, which is left in to protect the pump parts. If the fluid you are using may be

NOTE: The 100-mesh intake screen (9) should be replaced by the coarser 50-mesh screen when using large-orifice spray tips.

1. Connect the air supply. Raise the elevator by pulling out the knob of the elevator’s push/pull air valve.

2. Place a drum of fluid under the cover, against the elevator base.

8

Operation/Maintenance

3. Push in on the air valve knob to lower the elevator, so the cover (A) rests on the top lip of the drum.

The support clamp (K) recesses must be tight against the elevator riser tube. The pump intake valve feet (B) must contact and support the perforated plate (9) as shown in Fig. 2.

4. Raise the elevator 1/4” (6.4 mm), then tighten the support clamp screws. This ensures that the cover rests on the drum lip when the elevator is in the lowered position.

5. Adjust the restrictor valve screw to control the speed of raising and lowering the unit. Turn the restrictor screw clockwise to decrease the air pressure and counterclockwise to increase air pressure to the elevator. Lock the screw’s position with the locknut when the adjustment is completed.

6. Unscrew the filter bowl and remove the filter screen. Replace the bowl. Flush the unit until clear solvent comes from the gun, then reinstall the filter screen.

7. Before operation, ensure that all fasteners and tube connections are tightened securely.

Starting and Adjusting the Pump

1. Lower the pump into the fluid supply drum.

CAUTION

Do not allow the pump to run dry. It will quickly accelerate to a high speed, causing damage. If your pump is running too fast, stop it immediately and check the fluid supply. If the container is empty and air has been pumped into the lines, refill the container and prime the pump and the lines, or flush and leave it filled with a compatible solvent.

Eliminate all air from the fluid system.

9. With the pump and lines primed, and with adequate air pressure and volume supplied, the pump will start and stop as you open and close the gun. In a circulating system, the pump will speed up or slow down on demand, until the air supply is shut off.

WARNING

COMPONENT RUPTURE HAZARD

To reduce the risk of overpressurizing exceed the specified Maximum Incoming Air Pres sure to the pump. (see Technical Data on page 9.) your system, which could cause component rupture and serious injury, never

2. Close the air regulator (F).

3. Open the pump’s bleed-type master air valve (E).

4. Hold a metal part of the gun (S) firmly to the side of a grounded metal pail and hold the trigger open.

10. Use the air regulator (F) to control pump speed and fluid pressure. Always use the lowest air pressure necessary to get the desired results.

Higher pressures cause premature tip and pump wear.

5. Slowly open the regulator until the pump starts.

Shutdown and Care of the Pump

6. Cycle the pump slowly until all air is pushed out and the pump and hoses are fully primed.

WARNING

7. Release the gun trigger and lock the trigger safety.

The pump should stall against pressure.

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the

Pressure Relief Procedure on page 7.

8. If the pump fails to prime properly, open the drain valve (M). Use the drain valve as a priming valve until the fluid flows from the valve. Close the valve.

NOTE: When changing fluid containers with the hose and gun already primed, open the drain valve (M) to help prime the pump and vent air before it enters the hose. Close the drain valve when all air is eliminated.

For overnight shutdown, stop the pump at the bottom of its stroke to prevent fluid from drying on the exposed displacement rod and damaging the throat packings. Relieve the pressure.

Always flush the pump before the fluid dries on the displacement rod. See Flushing on page 7.

Manual Change Summary

This manual was changed from Rev. H to Rev. M and includes PCNs J, K, and L.

306-706

The following parts are changed in this revision:

Assembly Changed Part that

Changed

Model 231–063 sprayer

210–540

Ref

No.

7

Part Description Description of Change

Hose Replaced by Part No. 223–540:

HOSE, static-free; 1/4” ID, nylon tube; cpld 1/4” npsm (fbe); 25 ft (7.6 m) long, with spring guard

208–327 20 Hydra-Spray gun Replaced by Part No. 235–462:

SPRAY GUN, airless

See manual 308–236 for parts.

The following additional changes are made in this revision:

Pages 5–8: New Installation and Operation/Maintenance sections are added.

Technical Data

Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum fluid working pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30:1

3000 psi (210 bar)

Maximum air input pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pump cycles per 3.8 liters (1 gal.)

100 psi (7 bar)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5

Recommended pump speed for continuous operation

Maximum flow . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . 60 cycles per min

18.2 liters/min (4.8 gpm) at 60 cycles/min

Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lowered: 57 in. (1.5 m) raised: 96 in. (2.4 m)

Width

Depth

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17 in. (685 mm)

30 in. (760 mm)

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Wetted parts . . . . . . . . . . . . . . . . . . .

approx. 240 lb (109 kg) carbon steel; alloy steel; zinc and nickel plating; ductile iron; 304, 440 and 17–4 PH grades of stainless steel; tungsten carbide; PTFE ; leather

PTFE

306-706 9

Parts Drawing

Model 231–063, Series B, 30:1 President Hydra-Spray

1

42

25

26

47

24

12

21

48

30

28

32

8

49

9

19

39

2

23

31

3

40

22

37

38

36

20

34

29

17

6a

6b

6c

6d

6e

35

46

45

44

43

13, 14

10

18

5

15

20

4

7

04278

Parts List

Model 231–063, Series B, 30:1 President Hydra-Spray

8

9

10

11

12

2

3

4

5

6

6a

6b

6c

6d

Ref.

No.

Part No.

Description

1

6e

7

13

14

15

17

18

19

20

Qty.

202–295 VALVE, push-pull

See 306–287 for parts.

203–743 VALVE, restrictor

See 306–287 for parts.

204–385 ELEVATOR

1

1

See 306–287 for parts.

1

204–940 SWIVEL See 306–861 for parts.

1

204–995 AGITATOR

1 See 306–459 for parts.

205–306 INTAKE SCREEN ASSEMBLY

Includes items 6a to 6e.

101–368 . CLAMP

1

1

164–178 . HOUSING, screen

162–363 . PLATE

162–362 . SCREEN, 100 mesh;

Can be replaced with item 61.

1

162–416 . RING, retaining

223–540 HOSE, static free; nylon;

1

1

1

1/4” (6 mm) ID; 1/4 npsm (fbe);

25 ft (7.6 m) long, with spring guard

104–266 REGULATOR, air

214–724 FILTER, fluid

See 307–296 for parts.

202–776 BRACE, support

207–699 TUBE, riser

237–308 COVER, drum

See 308–466 for parts.

100–181 NUT, square; 5/16–18

100–214 WASHER, lock, spring; 5/16”

100–268 SCREW, rd hd, machine;

10–24 x 3/8” (10 mm)

100–057 SCREW, cap, hex hd;

5/16–18 x 3/4” (19 mm)

158–271 CLAMP, support

221–075 30:1 PRESIDENT PUMP

See 306–981 for parts.

235–462 SPRAY GUN, airless

See 308–236 for parts.

2

1

1

1

1

2

1

1

1

1

1

2

2

34

35

36

37

38

39

40

42

43

44

45

Ref.

No.

Part No.

Description

21

22

23

24

25

26

28

29

30

31

32

33

46

47

48

49

50

107–142 VALVE, air, bleed-type

100–112 FITTING, elbow;

1/4” tube x 1/8” npt (m)

Qty.

1

1

100–113 FITTING, straight compression;

1/4 (6.4 mm) tube x 1/8 npt(m)

100–960 GAUGE, air pressure

101–909 CONNECTOR, male;

1

112–896 SCREW, cap, hex hd;

1/4–20 x 1/2” (13 mm)

104–121 NUT, hex; 1/4–20

104–123 WASHER, spring lock; 1/4” size 4

4

2

1

1/2–28 x 3/8” tube; 1/4 npt(m)

158–491 NIPPLE; 1/2” npt

162–021 TUBE

161–262 MANIFOLD, air

162–746 SCREEN, 50 mesh; brass;

(not shown) Optional–can be used in place of item 8.

1

164–259 ELBOW; 1/4 npt(f) x 3/8 npt(m) 1

TIP, spray; customer’s choice

164–558 TUBE, drain

150–153 ADAPTER; 1/4 npt (fbe)

101–958 FITTING, tube; 9/16–18 x 3/8”

1

1

1

3

1

1

1

112–900

112–904

OD tube; 3/8 npt(m)

104–663 PLUG, pipe, sq hd; 3/4 npt

162–449 NIPPLE; 1/2 x 1/4 npt

190–231 BRACKET, valve

NUT, square; 5/16”

WASHER, lock, spring; 5/16”

112–894 SCREW, cap, hex hd;

5/16–18 x 3/4 ” (19 mm)

190–181 BRACKET, riser tube

187–357 ELBOW, street

155–470 SWIVEL; 1/2” npt(m) x 1/2 npsm(f)

100–721 PLUG, pipe

104–765 PLUG, pipe (not shown)

2

1

1

1

1

2

1

1

1

1

2

2

306-706 11

Warranty

WARRANTY

Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. As purchaser’s sole remedy for breach of this warranty, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment proven defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for, any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-

Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility with Graco equipment of structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claim. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor and transportation.

DISCLAIMERS AND LIMITATIONS

The terms of this warranty constitute purchaser’s sole and exclusive remedy and are in lieu of any other warranties (express or implied), including warranty of merchantability or warranty of fitness for a particular purpose , and of any non-contractual liabilities, including product liabilities, based on negligence or strict liability. Every form of liability for direct, special or consequential damages or loss is expressly excluded and denied. In no case shall Graco’s liability exceed the amount of the purchase price. Any action for breach of warranty must be brought within two (2) years of the date of sale.

EQUIPMENT NOT COVERED BY GRACO WARRANTY

Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose , with respect to accessories, equipment, materials, or components sold but not manufactured by Graco. These items sold, but not manufactured by Graco (such as electric motor, switches, hose, etc.) are subject to the warranty, if any, of their manufacturer.

Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

Graco Phone Numbers

TO PLACE AN ORDER , contact your Graco distributor, or call this number to identify the distributor closest to you: 1–800–367–4023 Toll Free

FOR TECHNICAL ASSIST ANCE, service repair information, or assistance regarding the application of

Graco equipment: 1–800–543–0339 Toll Free

Sales Offices: Atlanta, Chicago, Detroit, Los Angeles

Foreign Offices: Belgium, Canada, England, Korea, Switzerland, France, Germany, Hong Kong, Japan

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

PRINTED IN U.S.A. 306–706 December 1984, Revised September 1995

12 306-706

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement