Graco 307633E AIRLESS SPRAY GUN Owner's Manual

Add to my manuals
9 Pages

advertisement

Graco 307633E AIRLESS SPRAY GUN Owner's Manual | Manualzz
INSTRUCTIONS-PARTS LIST (3 307-633
Rev E
SUPERSEDES D
GRACO
This manual contains IMPORTANT
WARNINGS and INSTRUCTIONS
READ AND RETAIN FOR REFERENCE
AIRLESS SPRAY GUN
5000 psi (345 bar) MAXIMUM WORKING PRESSURE
Model 220-956, Series A
Includes Reverse-A-Clean IV DripLess™ Tip Guard and
517 size SwitchTip'". Has two finger trigger.
e Four finger trigger is optional (see page 8); please
specify when ordering
Warning... oro nonnn ara rene
Installation
¡SA cece eee ses.
ЗегМСе....... ааа: к ине и киа
Parts Drawing & List
How To Order Replacement Parts..................,........ 8
ACCOSSOMTBS...oococccccncnnnnnnnno rca n co rana nr rr rro rro rra 9
Technical Data................... nenn anne Back Cover
Warranty... ss Back Cover
NOTE: Gun Model 220-956 is the new part number
for 218-132, previously covered in this
manual.
GRACO INC. P.O. Box 1441 MINNEAPOLIS, MN 55440-1444
©COPYRIGHT 1983 GRACO INC.
WARNING
HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY.
FOR PROFESSIONAL USE ONLY. OBSERVE ALL WARNINGS.
Read and understand all instruction manuals before operating equipment.
FLUID INJECTION HAZARD
General Safety
This gun generates very high fluid pressure. Spray from the
gun, leaks or ruptured components can inject fluid through
your skin and into your body and cause extremely serious
bodily injury, including the need for amputation. Also, fluid in-
jected or splashed into the eyes or onto the skin can cause
serious damage.
NEVER point the spray gun at anyone or at any part of the
body. NEVER put hand or fingers over the spray tip.
ALWAYS have the tip guard in place when spraying.
ALWAYS follow the Pressure Relief Procedure, right,
before cleaning or removing the spray tip or servicing any
system equipment.
NEVER try to “blow back” paint; this is not an air spray gun.
NEVER try to stop or deflect leaks with your hand or body.
Be sure equipment safety devices are Operating properly
before each use.
Medical Alert— Airless Spray Wounds
If any fluid appears to penetrate your skin, get EMERGENCY
MEDICAL CARE AT ONCE. DO NOT TREAT AS A
SIMPLE CUT. Tell the doctor exactly what fluid was injected.
Note To Physician: Injection in the skin is a traumatic in-
jury. It is important to treat the Injury surgically as soon
as possible. Do not delay treatment to research toxicity.
Toxicity is a concern with some exotic coatings and injected
directly into the blood stream. Consultation with a plastic
surgeon or reconstructive hand surgeon may be advisable.
Spray Gun Safety Devices
Be sure all gun safety devices are operating properly before
each use. Do not remove or modify any part of the gun; this
can cause a malfunction and result in serious bodily injury.
Safety Latch
Whenever you stop spraying, even for a moment, always set
the gun safety latch in the closed or “safe” position, making
the gun inoperative. Improper needle adjustment (see page 6)
and/or failure to set the safety latch can result in accidental
triggering of the gun and cause a fluid injection injury.
Diffuser
The gun diffuser breaks up spray and reduces the risk of injec-
tion when the tip is not installed. Check diffuser operation
regularly. Follow the Pressure Relief Procedure, below,
then remove the Spray tip. Aim the gun into a metal pail,
holding the gun firmly to the pail. Using the lowest possible
pressure, trigger the gun. If the fluid emitted is not diffused in-
to an irregular stream, replace the diffuser immediately.
Tip Guard
ALWAYS have the tip guard in place on the gun while spray-
ing. The tip guard alerts you to the fluid injection hazard and
helps reduce, but does not prevent, the risk of accidentally
placing your fingers or any part of your body close to the spray
tip.
Trigger Guard
Never operate the gun without the fluid hose properly routed
through the hose guard spring. This allows the fluid hose to
function as a trigger guard to help prevent the gun from trig-
gering accidentally if it is dropped or bumped.
2 307-633
Spray Tip and Nozzle Safety
Use extreme caution when cleaning or changing spray tips. If
the spray tip clogs while Spraying, engage the gun safety latch
immediately. ALWAYS follow the Pressure Relief Pro-
cedure and then remove the Spray tip to clean it.
NEVER wipe off build-up around the spray tip until pressure is
fully relieved and the gun safety latch is engaged.
Pressure Relief Procedure
To reduce the risk of serious bodily injury, including fluid injec-
tion, and splashing in the eyes or on the skin, always follow
this procedure whenever you shut off the pump, when check-
ing or servicing any part of the system, when installing or
changing spray tips, and whenever you stop spraying.
. Engage the spray gun safety latch.
. Shut off the power to the pump and close any bleed-type
air valves.
Disengage the gun valve safety latch.
Hold a metal part of the gun firmly to a grounded metal
waste container and trigger to relieve the fluid pressure.
Engage the safety latch again.
. Open the pump drain valve (required in your system), hav-
ing a container ready to catch the drainage.
. Leave the drain valve open until you are ready to spray
again.
SN DN BW no
ff you suspect that the Spray tip or hose is clogged or that fluid
pressure is not fully relieved after following the steps above,
VERY SLOWLY loosen the tip guard or hose end coupling and
allow pressure to be relieved gradually, then remove complete-
ly. Now clear the tip or hose obstruction.
EQUIPMENT MISUSE HAZARD
General Safety
Any misuse of the spray equipment or accessories, such as
overpressurizing, modifying parts, using incompatible
chemicals and fluids, or using worn or damaged parts, can
cause them to rupture and result in fluid injection, splashing in
the eyes or on the skin or other serious bodily injury, fire, ex-
plosion or property damage.
NEVER alter or modify any part of this equipment: doing so
could cause it to malfunction.
CHECK all spray equipment regularly and repair or replace
worn or damaged parts immediately.
ALWAYS read and follow the fluid and solvent manufacturer’s
recommendations regarding the use of protective eyewear,
respirator, clothing and equipment.
System Pressure
This gun has a 5000 psi (345 bar) MAXIMUM WORKING
PRESSURE. NEVER exceed the stated maximum working
pressure of the supply pump or of the lowest rated component
in your system.
Fluid Compatibility
BE SURE that all fluid and solvent used are chemically com-
patible with the wetted parts shown in the Technical Data on
the back cover. Always read the fluid and solvent manufac-
turer's literature before using them in your system.
FIRE OR EXPLOSION HAZA RD :
Static electricity is created by the high velocity flow of fluid
through the pump and hose. If every part of the spray equip-
plug in or unplug any power supply cords in the spray area
when there is any chance of igniting fumes still in the air.
If you experience any static sparking or even a slight shock
while using this equipment, STOP SPRAYING IM-
MEDIATELY. Check the entire system for proper grounding.
Do not use the system again until the problem has been iden-
tified and corrected.
Grounding
To reduce the risk of static sparking, ground the pump and all
other spray equipment used or located in the spray area.
1. Pump or sprayer: as instructed in your separate pump or
sprayer manual.
2. Air hoses: use Only grounded air hoses.
3. Fluid hoses: use only grounded fluid hoses.
4. Air compressor: follow manufacturer’s recommendations.
HOSE SAFETY
High pressure fluid in the hoses can be very dangerous. if the
hose develops a leak, split or rupture due to any kind of wear,
damage or misuse, the high pressure spray emitted from it can
Cause an injection injury or other serious bodily injury or pro-
perty damage.
ALL FLUID SPRAY HOSES MUST HAVE SPRING
GUARDS ON BOTH ENDS! The spring guards help protect
the hose from kinks or bends at or close to the coupling which
can result in hose rupture.
TIGHTEN all fluid connections securely before each use. High
pressure fluid can dislodge a loose coupling or allow high
pressure spray to be emitted from the coupling.
NEVER use a damaged hose. Before each use, check entire
hose for cuts, leaks, abrasion, bulging cover, or damage or
movement of the hose couplings. If any of these conditions
exist, replace the hose immediately. DO NOT try to recouple
high pressure hose or mend it with tape or any other device. A
repaired hose cannot contain the high pressure fluid.
5. Spray gun: grounding is obtained through connection to a
properly grounded fluid hose and pump.
6. Fluid supply containers: according to local code.
7. Object being sprayed. according to your local code.
conductive surface, such as Paper or cardboard, which in-
terrupts the grounding continuity.
9. To maintain grounding continuity when flushing or reliev-
ing pressure, always hold a metal part of the gun/valve
firmly to the side of a grounded meta/ pail, then trigger the
gun/valve.
Flushing Safety
To reduce the risk of fluid injection injury, splashing in the
grounded metal pail and use the lowest possible fluid pressure
during flushing.
MOVING PARTS HAZARD if
Moving parts can pinch or amputate your fingers or other
body parts. Therefore, NEVER operate any of your equipment
with any parts removed. KEEP CLEAR of moving parts when
Starting or operating the pump. Before checking or servicing
the pump, follow the Pressure Relief Procedure on page 2
to prevent the pump from Starting accidentally.
HANDLE AND ROUTE HOSES CAREFULLY. Do not pull on
hoses to move equipment. Do not use fluids or solvents which
are not compatible with the inner tube and cover of the hose.
Hose Grounding Continuity
Proper hose grounding continuity is essential to maintaining a
grounded spray system. Check the electrical resistance of your
air and fluid hoses at least once a week. If your hose does not
have a tag on it which specifies the maximum electrical
resistance, contact the hose Supplier or manufacturer for the
maximum resistance limits. Use a resistance meter in the ap-
propriate range for your hose to check the resistance. If the
resistance exceeds the recommended limits, replace it im-
mediately. An ungrounded or poorly grounded hose can make
your system hazardous. Also, read FIRE OR EXPLOSION
HAZARD, above.
IMPORTANT
United States Government Safety standards have been adopted under the Occupational Safety and Health Act. These standards — par-
ticularly the General Standards, Part 1910, and the Construction Standards, Part 1926 — should be consulted.
TERMS
WARNING: Alerts user to avoid or correct conditions
that could cause bodily injury.
CAUTION: Alerts user to avoid or correct conditions
that could damage the equipment.
NOTE: Gives special Procedures or information.
307-633 3
INSTALLATION **
NOTE: Numbers and letters in parentheses in the
text correspond to the reference numbers
and letters in the drawings and parts list.
WARNING
Be sure your system has a bleed-type master air
valve (pneumatic pumps only) and a fluid drain
valve. These two accessories help reduce the risk
of serious bodily injury, including fluid injection,
splashing in the eyes, or on the skin, or injury from
moving parts, if you are adjusting or repairing the
pump or gun.
1. The bleed-type master air valve relieves air trap-
ped between this valve and the pump after the
air regulator is shut off. Trapped air can cause
the pump to cycle unexpectedly.
2. The fluid drain valve assists in relieving fluid
pressure in the displacement pump, hose and
gun: triggering the gun to relieve pressure may Fig 1
not be sufficient.
4. With the gun safety latch engaged, install the tip.
1. Connect a grounded fluid hose to the gun inlet. Refer to manual 307-848, supplied.
2. With no tip installed, start the pump/sprayer. Flush 5. Strain the fluid you are spraying if it contains par-
it according to the instructions supplied with it. ticles which could clog the spray tip.
Prime the system with the fluid you are using.
3. Follow the Pressure Relief Procedure on page 2.
OPERATION.
WARNING
To reduce the risk of serious bodily injury, in-
cluding fluid injection or splashing in the eyes or on
the skin, always follow the Pressure Relief Pro-
cedure Warning on page 2 before checking, ser-
vicing, installing, removing, changing or cleaning
spray tips or any part of the gun or system.
Whenever you stop spraying for a moment,
engage the gun safety latch. See Fig 2.
WARNING
The wallet-sized warning card provided with this TO DISENGAGE SAFETY
. . LATCH (OFF SAFE) TURN
gun should be kept with the operator at all times. LATCH PARALLEL TO BODY
The card contains important treatment information
should an injection injury occur. Additional cards
are available at no charge from Graco Inc.
1. Start the pump. Adjust the fluid pressure so the
spray is completely atomized. Always use the
lowest pressure necessary to get the desired results.
Higher pressure may not improve the spray pattern
and will cause premature tip and pump wear.
2. If adjusting the pressure does not give a good spray
pattern, try another tip size. Be sure to relieve
pressure completely before changing tips.
3. Use a full-open, full-close trigger action. Hold the
gun about 14 in. (350 mm) from and at right angles
to the work surface. Don’t swing the gun in an arc. TO ENGAGE SAFETY
< : LATCH, (ON SAFE) PULL
Practice to find the best length and speed of stroke. OUT LATCH AND TURN
TO RIGHT ANGLE WITH BODY
Fig 2
4 307-633
Adjust the Spray Pattern
1. To adjust the spray pattern direction, follow the
Pressure Relief Procedure Warning on page 2.
Engage the safety latch and loosen the tip guard re-
taining nut. Turn the tip guard so it is horizontal for
a horizontal spray pattern, and vertical for a vertical
pattern. Tighten the retaining nut.
2. The spray tip orifice size and spray angle determines
the coverage and size of pattern. When more
coverage is needed, use a larger spray tip rather
than increasing fluid pressure.
WARNING
To reduce the risk of a fluid injection injury,
NEVER use the gun with the tip guard or trigger
guard removed.
CAUTION
Openings in the tip guard are designed to reduce
paint buildup on the guard while spraying. Any
damage to the sharp edges of the openings causes
paint to collect at that area. To reduce the risk of
damage, never hang the gun by the tip guard.
Cleaning and Clearing the Spray Tip
WARNING
To reduce the risk of a fluid injection or splashing
in the eyes or on the skin, DO NOT hold your
hand, body, or a rag in front of the spray tip when
cleaning or checking a clogged tip. Always point
the gun toward the ground or into a waste con-
tainer when checking to see if the spray tip is
cleared.
DO NOT try to “blow back” paint; this is NOT an
air spray gun.
DO NOT wipe fluid buildup off the gun or spray tip
until pressure is relieved. See the Pressure Relief
Procedure Warning on page 2.
Clean off the front of the tip frequently during the day's
operation and at the end of the work day. Always follow
the Pressure Relief Procedure Warning on page 2.
Then use a solvent soaked brush to clean the spray tip
and to keep fluid buildup from drying and clogging the
spray tip.
If the spray tip clogs while spraying, release the spray
gun trigger, engage the trigger safety, shut off the
pump, and follow the Pressure Relief Procedure
Warning on page 2. Refer to manual 307-848, supplied,
for information on clearing a clog and cleaning the spray
tip.
NEVER soak the entire gun in solvent. Prolonged
exposure to solvent can ruin the packings.
CAUTION ]
Flushing the Gun
WARNING
Before flushing, be sure the entire system and
flushing pails are properly grounded. Refer to
Grounding, on page 3. Follow the Pressure
Relief Procedure Warning on page 2, and
remove the spray tip from the gun. Always use the
lowest possible fluid pressure, and maintain firm
metal to metal contact between the gun and the
pail during flushing to reduce the risk of a fluid in-
jection injury, static sparking and splashing.
Relieve pressure, remove the spray tip, and then flush
the gun and spray system with a compatible soivent.
Always flush the gun before the fluid being sprayed can
dry in it.
à
—— SE
\ M “Cu (LC TES
MAINTAIN FIRM
METAL TO METAL
CONTACT BETWEEN
GUN AND CONTAINER
Fig 3
307-633 5
SERVICE th
WARNING
To reduce the risk of serious bodily injury, in-
cluding fluid injection, splashing in the eyes or on
the skin always follow the Pressure Relief Pro-
cedure Warning on page 2 before adjusting,
cleaning or repairing this gun.
Periodically disassemble the gun to clean and inspect
parts. Clean all parts thoroughly, and check them
carefully for damage or wear. Replace parts as needed.
If your gun leaks at the tip when you release the trigger,
the needle or seat is worn or damaged and must be
replaced. See page 8 for available Repair Kit.
Needle Replacement (See Fig 4 and Parts Drawing)
NOTE: A tool, part no. 178-481, is available for
removing and installing a needle without
complete disassembly of the gun, and
without damaging the needle. The Needle
Replacement section tells how to use the
tool when you are replacing only the needle.
However, it can be used when you are
disassembling the entire gun.
Disassembly
Relieve pressure. Disconnect the hose. Remove the
tip guard, spray tip, and gasket. Remove the screw
(1), pivot pin (2) and trigger (10). Remove the plug
(3) at the rear of the gun. Remove the diffuser-seat
(15).
2. Insert the narrow end of tool 178-481 through the
rear of the gun and push out the needle (18**). A
rubber mallet may be required.
Reassembly
1. Lubricate the o-ring (D) and ring (E) of the new
needle assembly (18**) with lightweight oil.
2. Place the pointed end of the needle into the large
end of the tool. Guide the rear of the needle
through the front of the gun until the trigger flats
are exposed.
3. With new gasket (14) in place, screw the new
diffuser-seat (15) into the fluid housing. Torque to
15-20 ft-lb (20-27 N-m).
6 307-633
Needie Removal
TOOL
Needle Installation
NEEDLE
TOOL
MALLET
Fig 4
4. Install the trigger (10), pivot pin (2) and screw (1).
DO NOT install the plug (3) yet!
5. Adjust the needle before operating the gun. See
page 7.
Adjusting the Needle
WARNING
Proper adjustment of the needle is essential to be
sure the trigger safety latch makes the gun in-
Operative when engaged. Improper adjustment
may allow the gun to be triggered, even with the
trigger safety latch engaged, resulting in serious
bodily injury, including fluid injection and
splashing in the eyes or on the skin.
1. Hold the gun with the nozzle straight up so the trig-
ger falls onto the safety latch. Insert a flat blade
screwdriver into the rear port of the gun until it
engages with the slot (C) at the back of the needle.
See Fig 5.
NOTE: If the trigger does not touch the latch, turn the
needle clockwise until it does.
2. With light pressure, hold the trigger against the < >
latch. Turn the needie counterclockwise until there CLOCKWISE
is enough tension for you to feel and see the trigger
raise slightly off the latch.
3. Now turn the needie back 3/4 turn.
4. Install the plug (3).
5. Connect the fluid hoses and start the pump. Release
the trigger safety latch and trigger the gun into a
grounded waste container. Release the trigger: the
fluid should stop flowing immediately. Now engage
the safety again and try to trigger the gun; no fluid
should flow. If the gun failed either test, relieve
pressure, disconnect the hoses and adjust the needle Fig 5
again.
6. Place the tip (27) and new gasket (17) in the nut of
the tip guard. Screw the assembly firmly onto the
gun. Tighten with a wrench.
307-633
ae roo и
Bae НИЕ ER НЯ ets AEE IS BEE TER
и
Model 220-956, Series A
Includes items 1 to 27
PARTS LIST
REF PART
NO. NO.
1 203-953
2 160-217
3 103-219
4 218-642
5 107-257
6 1172-479
7 1180-044
8 218-139
10 169-550
10a 170-668
12 102-207
13 169-797
14 ** 156-766
15 **214-967
16 *220-422
18 **218-129
19 179-974
20 101-804
26 1179-960
27 *221-517
307 Number in
manual,
** 14
DESCRIPTION
SCREW, lock
PIN, pivot
PLUG, screw
GUN BODY ASSEMBLY
includes item 5
.SCREW, thread forming,
1/4-20 x 1/2”
TAG, instruction (not shown)
TAG, warning (not shown)
GUARD, hose
TRIGGER, 2 finger (standard)
TRIGGER, 4 finger (optional)
SETSCREW, soc hd cup pt:
1/4-20 x 1/4”
ADAPTER
GASKET, copper
DIFFUSER/SEAT
RAC IV DripLess Tip Guard
See 307-848
NEEDLE, fluid
HOUSING, fluid
PIN, spring, straight
CARD, warning (not shown)
SPRAY TIP; 517 size SwitchTip
TORQUE TO 20-25 ft-lb
(27-34 N:m)
— — = —
1
1
1
1
1
1
description refers to separate instruciton
TAdditional warning tags and cards available at no charge.
“Recommended “tool box” spare parts. Keep on hand to
reduce down time.
**Supplied in repair kit 218-143.
8
307-633
Gun Repair Kit 218-143
(Must be purchased separately)
Includes:
REFNO. QTY
14 1
15 1
*17 1
18 1
*Use only when using a flat tip
and non-reversing tip guard.
HOW TO ORDER REPLACEMENT PARTS:
1. To be sure you receive the correct replacement parts,
kit or accessories, always give all of the information
requested in the chart below.
2. Check the parts list to identify the correct part number;
do not use the ref. no. when ordering.
3. Order all parts from your nearest Graco distributor.
6 digit
PART
NUMBER QTY | PART DESCRIPTION
SERVICE INFORMATION NOTE:
Manual update to remove tip gasket from illustrations.
ACCESSORIES (Must be purchased separately) TECHNICAL DATA
NYLON BRUSHES Maximum working pressure : 5000 psi (345 bar)
101-891 0.375” (9 mm) dia. Fluid orifice : 0.09 in. (2.3 mm)
101-892 0.625” (16 mm) dia. Wetted parts : Stainless Steel, Tungsten
Carbide, Polyurethane,
Polyethylene, Plated Steel,
Copper
Weight : 21 oz. (595 д)
Inlet : 1/4 npsm(m)
WRENCH 171-147
NEEDLE TOOL 178-481
For inserting and removing needle without requiring
removal of fluid housing from gun. Also permits needle
replacement from the front of the gun.
THE GRACO WARRANTY AND DISCLAIMERS
WARRANTY
Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the date of sale
by an authorized Graco distributor to the original purchaser for use. As purchaser's sole remedy for breach of this warranty, Graco will, for a
period of twelve months from the date of sale, repair or replace any part of the equipment proven defective. This warranty applies only when the
equipment is installed, operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for, any malfunction, damage or wear caused by faulty installation, misapplication,
abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor
shall Graco be liable for malfunction, damage or wear caused by the incompatibility with Graco equipment of structures, accessories, equip-
ment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, ac-
cessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective for examination by Graco to verify the claimed
defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the
original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be
made at a reasonable charge, which charges may include the the costs of parts, labor and transportation.
DISCLAIMERS AND LIMITATIONS
THE TERMS OF THIS WARRANTY CONSTITUTE PURCHASER’S SOLE AND EXCLUSIVE REMEDY AND ARE IN LIEU OF ANY OTHER
WARRANTIES (EXPRESS OR IMPLIED), INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PAR-
TICULAR PURPOSE, AND OF ANY NON-CONTRACTUAL LIABILITIES, INCLUDING PRODUCT LIABILITIES, BASED ON NEGLIGENCE OR
STRICT LIABILITY. EVERY FORM OF LIABILITY FOR DIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES OR LOSS IS EXPRESSLY EX-
CLUDED AND DENIED. IN NO CASE SHALL GRACO'S LIABILITY EXCEED THE AMOUNT OF THE PURCHASE PRICE. ANY ACTION FOR
BREACH OF WARRANTY MUST BE BROUGHT WITHIN TWO (2) YEARS OF THE DATE OF SALE.
EQUIPMENT NOT COVERED BY GRACO WARRANTY
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR-
TICULAR PURPOSE, WITH RESPECT TO ACCESSORIES, EQUIPMENT, MATERIALS, OR COMPONENTS SOLD BUT NOT MANUFAC-
TURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motor, switches, hose, etc.), are subject to the warran-
ty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.
Factory Branches:Atlanta. Dallas, Detroit, Los Angeles, West Caldwell (N.J.)
Subsidiary and Affiliate Companies:Canada; England; Switzerland; France; Germany; Hong Kong; Japan
GRACO INC. P.O. Box 1441 MINNEAPOLIS, MN 55440-1444
PRINTED IN U.S.A. 307-633 5-83 Revised 8-87

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement