Graco 332457K, ProMix® PD2K Electronic Proportioner Owner's Manual

Add to my manuals
58 Pages

advertisement

Graco 332457K, ProMix® PD2K Electronic Proportioner Owner's Manual | Manualzz
Installation
ProMix® PD2K Electronic Proportioner
332457K
EN
fast--setting two
two--component materials. Manual system
Electronic positive displacement proportioner for fast
with Advanced Display Module. For professional use only.
Important Safety Instructions
Read all warnings and instructions in this manual. Save these
instructions.
See page 3 for model part numbers and
approvals information.
PROVEN QUALITY. LEADING TECHNOLOGY.
Contents
Related Manuals ................................................ 2
Models............................................................... 3
Warnings ........................................................... 6
Important Isocyanate (ISO) Information ................ 9
Important Acid Catalyst Information ..................... 11
Acid Catalyst Conditions............................... 11
Moisture Sensitivity of Acid Catalysts ............ 11
System Control Drawing 16P577 ......................... 12
Configuring Your System .................................... 14
1. Select a Base Model ................................ 14
2. Select Hoses ........................................... 19
3. Select Mixing Option ................................ 21
4. Select a Spray Gun .................................. 21
5. Select Color and Catalyst Change
Control Module Kits ........................ 22
6. Select Color and Catalyst Change
Manifold Kits .................................. 23
7. Select Pump Expansion Kits ..................... 25
8. Select Communication Options ................. 25
9. Accessory Tool Kit ................................... 25
General Information ............................................ 26
Location ............................................................. 26
Install the Display Module.................................... 27
Install the Booth Control ...................................... 28
Air Supply .......................................................... 29
Fluid Supply ....................................................... 31
Fluid Requirements ...................................... 31
Single Color Connections ............................. 32
Color Change Connections........................... 32
Solvent Connections .................................... 32
TSL Cup Kit........................................................ 33
Alternate TSL Plumbing for
Highly-Reactive/Moisture-Sensitive
ISO Catalyst PD2K Pumps .............. 35
Solvent Meter Accessory..................................... 37
Light Tower Accessory........................................ 37
Electrostatic Air Hose Quick Disconnect Kit
24S004................................................. 37
Electrical Supply ................................................. 38
Electrical Requirements................................ 38
Electrical Connections .................................. 38
Grounding .......................................................... 39
Electrical Schematics.......................................... 42
Standard Models (MC1000, MC2000,
MC3000, MC4000) ......................... 42
Dual Panel Models (MC1002, MC2002,
MC3002, MC4002) ......................... 48
Optional Cables and Modules ....................... 54
Dimensions ........................................................ 55
Technical Data ................................................... 56
Related Manuals
Manual No.
Description
3A2800
PD2K Proportioner Repair-Parts Manual, Manual Systems
332562
PD2K Proportioner Operation Manual, Manual Systems
3A4186
PD2K Dual Panel Proportioner Opertion Manual, Manual Systems
3A2801
Mix Manifold Instructions-Parts Manual
332339
Pump Repair-Parts Manual
332454
Color Change Valve Repair-Parts Manual
332455
Color Change Kits Instructions-Parts Manual
333282
Color Change and Remote Mix Manifold Kits Instructions-Parts Manual
332456
3rd and 4th Pump Kits Instructions-Parts Manual
334512
PD1K Pump Expansion Kits Instructions-Parts Manual
3A4497
Air Control Box Kit Instructions Manual
2
332457K
Models
Models
See Figs. 1–7 for component identification labels, including approval information and certification.
Part No.
Series
Maximum Air Working
Pressure
Maximum Fluid Working
Pressure
MC0500
MC0502
A
100 psi (0.7 MPa,
7.0 bar)
With low–pressure pumps:
300 psi (2.068 MPa, 20.68 bar)
Location of PD2K and
Electrical Control Box
(ECB) Labels
With high–pressure pumps:
1500 psi (10.34 MPa,
103.4 bar)
MC1000
MC1002
A
100 psi (0.7 MPa,
7.0 bar)
300 psi (2.068 MPa, 20.68 bar)
A
100 psi (0.7 MPa,
7.0 bar)
1500 psi (10.34 MPa,
103.4 bar)
MC3000
MC3002
Acid-based
Material
MC2000
MC2002
MC4000
M4002
Acid-based
Material
0359
II 2 G
®
ProMix PD2K / PD1K
Electronic Proportioner
II 2 G
Ex ia IIA T3
FM13 ATEX 0026
IECEx FMG 13.0011
FM16US0241
FM16CA0129
Intrinsically safe
equipment for Class I,
Div 1, Group D, T3
Ta = 2°C to 50°C
.7
7
100
MPa
bar
PSI
MAX FLUID WPR
2.068 20.68
MPa
bar
300
PSI
MAX TEMP 50°C (122°F)
Figure 1 Models MC1000, MC1002, MC3000, and
MC3002 (Low Pressure) Identification Label
332457K
Artwork No. 294021 Rev. F
MAX AIR WPR
Intrinsically Safe (IS) System. Install
per IS Control Drawing No. 16P577.
Control Box IS Associated
Apparatus for use in non hazardous
location, with IS Connection to color
change and booth control modules
Apparatus for use in:
Class I, Division 1, Group D T3
Hazardous Locations
Read Instruction Manual
Warning: Substitution of components
may impair intrinsic safety.
PART NO.
MFG. YR.
SERIES
SERIAL
GRACO INC.
P.O. Box 1441
Minneapolis, MN
55440 U.S.A.
Continued on the next page.
3
®
POWER REQUIREMENTS
ProMix PD2K / PD1K
PART NO. SERIES NO. MFG. YR.
90-250 ~
VOLTS
AMPS 7 AMPS MAX
Intrinsically safe connections
for Class I, Div 1, Group D
GRACO INC.
Ta = 2°C to 50°C
P.O. Box 1441
II (2) G
Install per 16P577
[Ex ia] IIA Gb
Minneapolis, MN FM16US0241
FM13 ATEX 0026
55440 U.S.A.
FM16CA0129 Um: 250 V
IECEx FMG 13.0011
50/60 Hz
Artwork No. 294024 Rev. D
Models
Figure 2 24M672 & 26A188 Control Box Identification
Label
®
ProMix PD2K / PD1K
Electronic Proportioner
II 2 G
Ex ia IIA T3
FM13 ATEX 0026
IECEx FMG 13.0011
FM16US0241
FM16CA0129
Intrinsically safe
equipment for Class I,
Div 1, Group D, T3
Ta = 2°C to 50°C
.7
7
100
MPa
bar
PSI
MAX FLUID WPR
10.34 103.4 1500
MPa
bar
PSI
MAX TEMP 50°C (122°F)
Artwork No. 294022 Rev. F
MAX AIR WPR
Intrinsically Safe (IS) System. Install
per IS Control Drawing No. 16P577.
Control Box IS Associated
Apparatus for use in non hazardous
location, with IS Connection to color
change and booth control modules
Apparatus for use in:
Class I, Division 1, Group D T3
Hazardous Locations
Read Instruction Manual
Warning: Substitution of components
may impair intrinsic safety.
PART NO.
SERIES
MFG. YR.
SERIAL
GRACO INC.
P.O. Box 1441
Minneapolis, MN
55440 U.S.A.
Figure 3 Models MC2000, MC2002, MC4000, and
MC4002 (High Pressure) Identification Label
Figure 4 Non-Intrinsically Safe Color Change Control (Accessory) Identification Label
ProMix® PD2K / PD1K COLOR CHANGE CONTROL
PART NO.
SERIES
Intrinsically safe equipment
for Class I, Div 1, Group D, T3
Ta = 2°C to 50°C
Install per 16P577
FM16US0241 FM16CA0129
Artwork No. 294055 Rev. C
Figure 5 Intrinsically Safe Color Change Control
(Accessory) Identification Label
4
MAX AIR WPR
SERIAL MFG. YR.
II 2 G
Ex ia IIA T3 Gb
FM13 ATEX 0026
IECEx FMG 13.0011
.7
7
MPa
bar
100
PSI
GRACO INC.
P.O. Box 1441
Minneapolis, MN
55440 U.S.A.
Continued on the next page.
332457K
Models
www.graco.com/patents
12 VDC FM16US0241
FM16CA0129
II 2 G
Ex ia IIA T3 Gb
FM13 ATEX 0026
IECEx FMG 13.0011
Intrinsically safe
equipment for
Class I, Div 1,
Group D, T3
Install per 16P577
Ta = 2°C to 50°C
Figure 6 Booth Control Identification Label
Figure 7 Pump Expansion Kit (Accessory) Identification Label
332457K
5
Warnings
Warnings
The following warnings are for the setup, use, grounding, maintenance and repair of this equipment. The
exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific
risks. When these symbols appear in the body of this manual or on warning labels, refer back to these
Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout
the body of this manual where applicable.
WARNING
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. Paint
or solvent flowing through the equipment can cause static sparking. To help prevent fire and
explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and
plastic drop cloths (potential static arc).
• Ground all equipment in the work area. See Grounding instructions.
• Never spray or flush solvent at high pressure.
• Keep work area free of debris, including solvent, rags and gasoline.
• Do not plug or unplug power cords, or turn power or light switches on or off when flammable
fumes are present.
• Use only grounded hoses.
• Hold gun firmly to side of grounded pail when triggering into pail. Do not use pail liners unless
they are antistatic or conductive.
• Stop operation immediately if static sparking occurs or you feel a shock, Do not use
equipment until you identify and correct the problem.
• Keep a working fire extinguisher in the work area.
ELECTRIC SHOCK HAZARD
This equipment must be grounded. Improper grounding, setup, or usage of the system can
cause electric shock.
• Turn off and disconnect power at main switch before disconnecting any cables and before
servicing or installing equipment.
• Connect only to grounded power source.
• All electrical wiring must be done by a qualified electrician and comply with all local codes
and regulations.
6
332457K
Warnings
WARNING
INTRINSIC SAFETY
Intrinsically safe equipment that is installed improperly or connected to non-intrinsically safe
equipment will create a hazardous condition and can cause fire, explosion, or electric shock.
Follow local regulations and the following safety requirements.
• Be sure your installation complies with national, state, and local codes for the installation of
electrical apparatus in a Class I, Group D, Division 1 (North America) or Class I, Zones 1
and 2 (Europe) Hazardous Location, including all of the local safety fire codes (for example,
NFPA 33, NEC 500 and 516, OSHA 1910.107, etc.).
• To help prevent fire and explosion:
• Do not install equipment approved only for a non-hazardous location in a hazardous
location. See model ID label for the intrinsic safety rating of your model.
• Do not substitute system components as this may impair intrinsic safety.
• Equipment that comes in contact with the intrinsically safe terminals must be rated for Intrinsic
Safety. This includes DC voltage meters, ohmmeters, cables, and connections. Remove the
unit from the hazardous area when troubleshooting.
SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may
look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical
treatment.
•
•
•
•
•
•
Do not spray without tip guard and trigger guard installed.
Engage trigger lock when not spraying.
Do not point gun at anyone or at any part of the body.
Do not put your hand over the spray tip.
Do not stop or deflect leaks with your hand, body, glove, or rag.
Follow the Pressure Relief Procedure when you stop spraying/dispensing and before
cleaning, checking, or servicing equipment.
• Tighten all fluid connections before operating the equipment.
• Check hoses and couplings daily. Replace worn or damaged parts immediately.
MOVING PARTS HAZARD
Moving parts can pinch, cut or amputate fingers and other body parts.
• Keep clear of moving parts.
• Do not operate equipment with protective guards or covers removed.
• Pressurized equipment can start without warning. Before checking, moving, or servicing
equipment, follow the Pressure Relief Procedure and disconnect all power sources.
332457K
7
Warnings
WARNING
TOXIC FLUID OR FUMES
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin,
inhaled, or swallowed.
• Read Safety Data Sheet (SDS) for handling instructions and to know the specific hazards of
the fluids you are using, including the effects of long-term exposure.
• When spraying, servicing equipment, or when in the work area, always keeps work area
well ventilated and always wear appropriate personal protective equipment. See Personal
Protective Equipment warnings in this manual.
• Store hazardous fluid in approved containers, and dispose of it according to applicable
guidelines.
PERSONAL PROTECTIVE EQUIPMENT
Always wear appropriate personal protective equipment and cover all skin when spraying,
servicing equipment, or when in the work area. Protective equipment helps prevent serious
injury, including long-term exposure; inhalation of toxic fumes, mists, or vapors; allergic
reactions; burns; eye injury and hearing loss. This protective equipment includes, but is not
limited to:
• A properly fitting respirator, which may include a supplied-air respirator, chemically
impermeable gloves, protective clothing and foot coverings as recommended by the fluid
manufacturer and local regulatory authority.
• Protective eyewear, and hearing protection.
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated
system component. See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data
in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete
information about your material, request SDS from distributor or retailer.
• Do not leave the work area while equipment is energized or under pressure.
• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine
manufacturer’s replacement parts only.
• Do not alter or modify equipment. Alterations or modifications may void agency approvals
and create safety hazards.
• Make sure all equipment is rated and approved for the environment in which you are using it.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
8
332457K
Important Isocyanate (ISO) Information
Important Isocyanate (ISO) Information
Isocyanates (ISO) are catalysts used in two
component materials.
Self--ignition
Material Self
Isocyanate Conditions
Some materials may become self-igniting if applied
too thick. Read material manufacturer’s warnings
and Safety Data Sheet (SDS).
Spraying or dispensing fluids that contain
isocyanates creates potentially harmful mists,
vapors, and atomized particulates
Keep Components A and B Separate
• Read and understand the fluid manufacturer’s
warnings and Safety Data Sheet (SDS) to know
specific hazards and precautions related to
isocyanates.
• Use of isocyanates involves potentially
hazardous procedures. Do not spray with the
equipment unless you are trained, qualified,
and have read and understood the information
in this manuals and in the fluid manufacturer’s
application instructions and SDS.
Cross-contamination can result in cured
material in fluid lines which could cause serious
injury or damage equipment. To prevent
cross-contamination:
• Use of incorrectly maintained or mis-adjusted
equipment may result in improperly cured
material. Equipment must be carefully
maintained and adjusted according to
instructions in the manual.
• Never use solvent on one side if it has been
contaminated from the other side.
• Never interchange component A and component
B wetted parts.
• To prevent inhalation of isocynate mists, vapors,
and atomized particulates, everyone in the
work area must wear appropriate respiratory
protection. Always wear a properly fitting
respirator, which may include a supplied-air
respirator. Ventilate the work area according to
instructions in the fluid manufacturer’s SDS.
• Avoid all skin contact with iscocyanates.
Everyone in the work area must wear chemically
impermeable gloves, protective clothing and
foot coverings as recommended by the fluid
manufacturer and local regulatory authority.
Follow all fluid manufacturer recommendations,
including those regarding handling of
contaminated clothing. After spraying, wash
hands and face before eating or drinking.
332457K
9
Important Isocyanate (ISO) Information
Moisture Sensitivity of Isocyanates
Exposure to moisture (such as humidity) will cause
ISO to partially cure; forming small, hard, abrasive
crystals, which become suspended in the fluid.
Eventually a film will form on the surface and the ISO
will begin to gel, increasing in viscosity.
NOTICE
Partially cured ISO will reduce performance and
the life of all wetted parts.
• Always use a sealed container with a desiccant
dryer in the vent, or a nitrogen atmosphere.
Never store ISO in an open container.
• Keep the ISO pump wet cup or reservoir (if
installed) filled with appropriate lubricant. The
lubricant creates a barrier between the ISO and
the atmosphere.
• Use only moisture-proof hoses compatible with
ISO.
• Never use reclaimed solvents, which may
contain moisture. Always keep solvent
containers closed when not in use.
NOTE: The amount of film formation and rate of
crystallization varies depending on the blend of ISO,
the humidity, and the temperature.
Changing Materials
NOTICE
Changing the material types used in your
equipment requires special attention to avoid
equipment damage and downtime.
• When changing materials, flush the equipment
multiple times to ensure it is thoroughly clean.
• Always clean the fluid inlet strainers after
flushing.
• Check with your material manufacturer for
chemical compatibility.
• When changing between epoxies and urethanes
or polyureas, disassemble and clean all fluid
components and change hoses. Epoxies often
have amines on the B (hardener) side. Polyureas
often have amines on the A (resin) side.
• Always lubricate threaded parts with an
appropriate lubricant when reassembling.
10
332457K
Important Acid Catalyst Information
Important Acid Catalyst Information
The PD2K MC3000 and MC4000 Proportioner is designed for acid catalysts (“acid”) currently used in
two-component, wood-finishing materials. Current acids in use (with pH levels as low as 1) are more corrosive
than earlier acids. More corrosion-resistant wetted materials of construction are required, and must be used
without substitution, to withstand the increased corrosive properties of these acids.
Acid Catalyst Conditions
Acid is flammable, and spraying or dispensing acid creates potentially harmful mists, vapors, and atomized
particulates. To help prevent fire and explosion and serious injury:
• Read and understand the acid manufacturer’s warnings and Safety Data Sheet (SDS) to know specific
hazards and precautions related to the acid.
• Use only genuine, manufacturer’s recommended acid-compatible parts in the catalyst system (hoses,
fittings, etc). A reaction may occur between any substituted parts and the acid.
• To prevent inhalation of acid mists, vapors, and atomized particulates, everyone in the work area must
wear appropriate respiratory protection. Always wear a properly fitting respirator, which may include a
supplied-air respirator. Ventilate the work area according to instructions in the acid manufacturer’s SDS.
• Avoid all skin contact with acid. Everyone in the work area must wear chemically impermeable gloves,
protective clothing, foot coverings, aprons, and face shields as recommended by the acid manufacturer
and local regulatory authority. Follow all acid manufacturer recommendations, including those regarding
handling of contaminated clothing. Wash hands and face before eating or drinking.
• Regularly inspect equipment for potential leaks and remove spills promptly and completely to avoid direct
contact or inhalation of the acid and its vapors.
• Keep acid away from heat, sparks, and open flames. Do not smoke in the work area. Eliminate all
ignition sources.
• Store acid in the original container in a cool, dry, and well-ventilated area away from direct sunlight and
away from other chemicals in accordance with acid manufacturer’s recommendations. To avoid corrosion
of containers, do not store acid in substitute containers. Reseal the original container to prevent vapors
from contaminating the storage space and surrounding facility.
Moisture Sensitivity of Acid Catalysts
Acid catalysts can be sensitive to atmospheric
moisture and other contaminants. It is recommended
the catalyst pump and valve seal areas exposed to
atmosphere are flooded with ISO oil, TSL, or other
compatible material to prevent acid build-up and
premature seal damage and failure.
NOTICE
Acid build-up will damage the valve seals and
reduce the performance and life of the catalyst
pump. To prevent exposing acid to moisture:
• Always use a sealed container with a desiccant
dryer in the vent, or a nitrogen atmosphere.
Never store acids in an open container.
• Keep the catalyst pump and the valve seals filled
with the appropriate lubricant. The lubricant
creates a barrier between the acid and the
atmosphere.
• Use only moisture-proof hoses compatible with
acids.
• Always lubricate threaded parts with an
appropriate lubricant when reassembling.
332457K
11
System Control Drawing 16P577
System Control Drawing 16P577
Do not substitute or modify system components
as this may impair intrinsic safety. For installation,
maintenance, or operation instructions, read
instruction manuals. Do not install equipment
approved only for non-hazardous location in a
hazardous location. See the identification label for
the intrinsic safety rating for your model.
NOTES FOR SYSTEM CONTROL DRAWING 16P577 (FM13ATEX0026 SYSTEM ASSEMBLY
CERTIFICATE)
Alternate M12 CAN Cables, for Hazardous Locations
Cable Part No.
Length ft (m)
16V423
2.0 (0.6)
16V424
3.0 (1.0)
16V425
6.0 (2.0)
16V426
10.0 (3.0)
16V427
15.0 (5.0)
16V428
25.0 (8.0)
16V429
50.0 (16.0)
16V430
100.0 (32.0)
2. The non-intrinsically safe terminals (power rail) must not be connected to any device which uses or
generates more than Um = 250 Vrms or dc unless it has been determined that the voltage has been
adequately isolated.
3. The electrical enclosure ground screw must be connected to a true earth ground using the supplied
ground strap (223547) or by an equivalent 10 AWG or larger isolated conductor. Resistance from the
electrical enclosure ground to the true earth ground shall not exceed 1 ohm.
4. Multiple earthing of components is allowed. Intrinsically safe apparatus provides isolation from earth to
500 Vrms.
Do not operate system with power barrier cover removed.
6. Installation should be in accordance with ANSI/ISA RP12.06.01 “Installation of Intrinsically Safe Systems
for Hazardous (Classified) Locations” and the National Electrical Code® (ANSI/NFPA 70).
7. Installation in Canada should be in accordance with the Canadian Electrical Code, CAS C22.1, Part I,
Appendix F.
8. For ATEX, install per EN 60079–14 and applicable local and national codes.
9. For IECEx install per IEC 60079–14 and applicable local and national codes.
12
332457K
System Control Drawing 16P577
NON--HAZARDOUS LOCATION ONLY
NON
HAZARDOUS (CLASSIFIED) LOCATION
Class 1, Div 1, Group D, T3 (USA and Canada)
Class 1, Zone 1, Group IIA, T3 (ATEX and IECEx)
Ta = 2°C to 50°C
HAZARDOUS (CLASSIFED) LOCATION
NON-HAZARDOUS LOCATION ONLY
CLASS 1, DIV 1, GROUP D, T3 (USAAND CANADA)
CLASS 1, ZONE 1, GROUP IIA, T3 (ATEXAND IECEx)
Ta = 2
C TO 50 C
POWER IN
250 VAC MAXIMUM SUPPL
Y VOLTAGE
BOOTH CONTROL
(24M731)
FM13ATEX0026
IECEx FMG 13.0011
INTRINSIC SAFE APPARATUS
5
COMMUNICA
TION
BARRIE
R
(24M485)
J4
OR
CABLE (16V
429)
CABLE (16V
429)
J3
CABLE
(16V426)
FM13ATEX0026
IECEx FMG 13.0011
ASSOCIATED APPARATUS
CABLE
(16V426)
POWER
BARRIE
R
(248192)
SPLITTER
17L058
PROMIX PD2K
ELECTRICAL ENCLOSURE
(24M672)
COLOR CHANGE MODULE
(24R219, 24R220, 24R221, 24R222)
(24V406, 24V407, 24V408)
(24V409, 24V410, 24V411)
FM13ATEX0026
IECEx FMG 13.0011
INTRINSIC SAFE APPARATUS
COLOR CHANGE MODULE
(24R219, 24R220, 24R221, 24R222)
(24V406, 24V407, 24V408)
(24V409, 24V410, 24V411)
FM13ATEX0026
IECEx FMG 13.0011
INTRINSIC SAFE APPARATUS
BOOTH CONTROL
(24M731)
FM13ATEX0026
IECEx FMG 13.0011
INTRINSIC SAFE APPARATUS
Figure 8 System Control Drawing 16P577
332457K
13
Configuring Your System
Configuring Your System
1. Select a Base Model
Choose a PD2K base model that meets your
application’s requirements. See Models, page 3 .
If using a mix-at-wall configuration, see Figure 10,
page 14.
Base models include components A through F
shown in the Typical Installation Drawing. Base unit
components are described in the following table.
Component
Description
Fluid Pumps (A, B)
The base models include two fluid pumps, one for resin and one for
catalyst. Install in the non-hazardous area.
Solvent Valve (C)
Dispenses solvent to the gun during purge.
Booth Control (D)
The booth control enables the user to monitor and control the system.
Install the booth control in the hazardous location, near the painter.
Electrical Control Box (E)
The electrical control box includes a barrier board, intrinsically safe
isolation board, 24 Vdc and 48 Vdc power supplies, Enhanced Fluid
Control Module, and Pump Control Modules. It accepts 90–250 Vac line
power and converts that power to acceptable low voltage signals used
by other system components. Install the electrical control box in the
non-hazardous area.
Advanced Display Module (F)
The Advanced Display Module (ADM) enables the user to setup, monitor,
and control the system. Install the ADM in the non-hazardous area.
14
332457K
Configuring Your System
HAZARDOUS (CLASSIFIED) LOCATION
NON--HAZARDOUS LOCATION ONLY
NON
Figure 9 Typical Installation
Component
Description
★ Components A through F are included with the base unit.
A★
Material A (Color) Pump
B★
Material B (Catalyst) Pump
C★
Solvent Valve
D★
Booth Control
E★
Electrical Control Box
F★
Advanced Display Module
Components G through K are included in optional color change kits.
G
Color Change Valves (accessory)
H
Color Change Module (accessory)
J
Catalyst Change Valves (accessory)
K
Catalyst Change Module (accessory)
Components L through S are accessories and must be ordered separately.
L
Fluid/Air Hose Bundle (accessory)
M
Mix Manifold (accessory)
N
Air Spray Gun (accessory)
P
Gun Air Hose (accessory)
R
Intrinsically Safe CAN Cable (to connect booth control to electrical control box)
S
Gun Fluid Hose (accessory)
332457K
15
Configuring Your System
HAZARDOUS (CLASSIFIED) LOCATION
NON--HAZARDOUS LOCATION ONLY
NON
Figure 10 Typical Installation with Remote Mix
Manifold
Description
Component
★ Components A through F are included with the base unit.
A★
Material A (Color) Pump
B★
Material B (Catalyst) Pump
C★
Solvent Flow Switch
D★
Electrical Control Box
E★
Advanced Display Module
F★
CAN Communication Cable
Components G through K are included in optional color change kits.
G
Color Change Valves (accessory, non-hazardous area)
H
Color Change Module (accessory, non-hazardous area)
J
Catalyst Change Valves (accessory, non-hazardous area)
K
Catalyst Change Module (accessory, non-hazardous area)
Components L through U are accessories and must be ordered separately.
L
M
N
P
R
S
T
U
16
Fluid/Air Hose Bundle (accessory)
Remote Color Change Manifold (accessory, hazardous area)
Remote Mix Manifold (accessory, hazardous area)
Air Spray Gun (accessory)
IS Remote Mix Control Module (accessory, hazardous area)
Gun Fluid Hose (accessory)
Supply Line Drain Valves (accessory, required, not shown)
Gun Air Hose (accessory)
332457K
Configuring Your System
HAZARDOUS (CLASSIFIED) LOCATION
NON--HAZARDOUS LOCATION ONLY
NON
Figure 11 Typical Dual Panel Installation (MC1002,
MC2002, MC4002)
Component
Description
★ Components A through F are included with the base unit.
A★
Material A (Color) Pump
B★
Material B (Catalyst) Pump
C★
Solvent Valve
D★
Booth Control
E★
Electrical Control Box
F★
Advanced Display Module
Components G through K are included in optional color change kits.
G
Color Change Valves (accessory)
H
Color Change Module (accessory)
J
Catalyst Change Valves (accessory)
K
Catalyst Change Module (accessory)
332457K
17
Configuring Your System
Component
Description
Components L through T are accessories and must be ordered separately.
L
Fluid/Air Hose Bundle (accessory) — see PD2K Installation Manual
(332457) for acid-compatible hose bundles
M
Mix Manifold (accessory) — see Mix Manifold Instruction-Parts Manual
(3A2801) for acid-compatible mix manifolds
N
Air Spray Gun (accessory)
P
Gun Air Hose (accessory)
R
Intrinsically Safe CAN Cable (to connect booth control to electrical control
box)
S
Gun Fluid Hose (accessory)
T
Air Control Module (accessory) — see Air Control Module Kit Manual
(3A4497)
18
332457K
Configuring Your System
2. Select Hoses
Hose Selection Tool
Use this chart to determine the proper size hose
bundle for your mix ratio and viscosity, then select a
hose bundle for your application from the tables on
the following page.
NOTE: Always use Graco hoses.
NOTE: Shaded areas may use hose sizes from either
of the two adjacent areas.
LOW PRESSURE SYSTEM, 0–300 psi (0–2.1 MPa, 0–21 bar)
Recommended Hose Sizes (internal diameter) for A and B
20 - 50
18
3/8 ʺ A
1/8 ʺ B
16
14
3/8 ʺ A
1/4 ʺ B
12
10
Mix
Ratio
(X:1)
8
1/4 ʺ A
1/4 ʺ B
6
4
2
0
10:1
Thick Resin (A)
1/4 ʺ A
3/8 ʺ B
7.5:1
5:1
2.5:1
1:1
1:2.5
Equal Viscosities
Thin Catalyst (B)
1:5
1:7.5
1:10
Thin Resin (A)
Thick Catalyst (B)
Viscosity Ratio (Resin [A] : Catalyst [B]
332457K
19
Configuring Your System
1/4 in. (6 mm) ID Hose Bundles
Select a hose bundle from the following table. Always use Graco hoses.
Application
Low Pressure
Conventional Air
Spray
Hose Bundle Length
Part No.
Material and Description
24T140
Nylon (A side and Solvent, both are
white/translucent, solvent is marked with
a band of black tape), Moisture Guard (B
side, red), Air Hose
24T141
24T138
Low Pressure
Electrostatic Air
Spray*
24T139
24T247
25A524**
24T248
25A525**
24T245
High Pressure
25A522**
Electrostatic
Air-Assisted Spray* 24T246
25A523**
High Pressure
Conventional
Air-Assisted Spray
25 ft
(7.6 m)
50 ft
(15.2 m)
25 ft
(7.6 m)
50 ft
(15.2 m)
25 ft
(7.6 m)
50 ft
(15.2 m)
25 ft
(7.6 m)
50 ft
(15.2 m)
Maximum
Fluid Working
Pressure
Nylon (A side and Solvent, both are
white/translucent, solvent is marked with
a band of black tape), Moisture Guard
(B side; red), Grounded Air Hose with
left-hand thread
Nylon (A side and Solvent, both are blue,
solvent is marked with a band of black
tape), Moisture Guard (B side, red), Air
Hose
225 psi (1.6
MPa, 16 bar)
225 psi (1.6
MPa, 16 bar)
2000 psi (13.8
MPa, 138 bar)
Nylon (A side and Solvent, both are
blue, solvent is marked with a band of
2000 psi (13.8
black tape), Moisture Guard (B side, red), MPa, 138 bar)
Grounded Air Hose with left-hand thread
* To use a quick disconnect on an existing electrostatic air hose, see
Electrostatic Air Hose Quick Disconnect Kit 24S004, page 37.
** Has PTFE and SST catalyst hose for acid applications.
3/8 in. (10 mm) ID Fluid Hoses
If 3/8 in. (10 mm) fluid hose is required for your application, order one of the following to replace the 1/4 in.
hose in your hose bundle. Always use Graco hoses.
Application
Hose Part
No.
Low Pressure Air 24T763
Spray
24T764
Length
Material
25 ft (7.6 m)
50 ft (15.2 m)
Nylon
Maximum Fluid Working Pressure
200 psi (1.4 MPa, 13.8 bar)
Fluid Whip Hoses
Select a fluid whip hose from the following table. Always use Graco hoses.
Application
Low Pressure
Hose Part
No.
24N641
24N305
24N641
High Pressure
20
24N348
Hose I.D.
Length
Material
0.125 in.
(3 mm)
0.25 in.
(6 mm)
0.125 in.
(3 mm)
0.25 in.
(6 mm)
6 ft (1.8 m)
Nylon
6 ft (1.8 m)
Nylon
6 ft (1.8 m)
Nylon
6 ft (1.8 m)
PTFE
Maximum Fluid Working
Pressure
3200 psi (22 MPa, 220
bar)
225 psi (1.6 MPa, 16 bar)
3200 psi (22 MPa, 220
bar)
3000 psi (20.7 MPa, 207
bar)
332457K
Configuring Your System
3. Select Mixing Option
The system will use either a Mix at Belt Manifold or a
Wall Mounted Mix Manifold.
3a. Mix At Belt Using Mix Manifold
The following mix manifold kits are available. The mix
manifolds attach to the painter’s belt, allowing mixing
to occur at the point of spray. See the ProMix Mix
Manifold Kit manual in Related Manuals, page 2 , for
further information.
Mix Manifold
Description
Maximum Fluid Working Pressure
24R991
Low pressure mix manifold
300 psi (2.1 MPa, 21 bar)
24R992
High pressure mix manifold
1500 psi (10.5 MPa, 105 bar)
24T273
High pressure mix manifold, for
acid-compatible materials
1500 psi (10.5 MPa, 105 bar)
3b. Mix At Wall Using Remote Mix Manifold
The following remote mix manifold kits are
available. The mix manifolds may be attached to
the wall, in the hazardous area, allowing mixing to
occur close to the point of spray. See the Color
Change and Remote Mix Manifold Kits manual in
Related Manuals, page 2 , for more information.
Mix Manifold
Description
Maximum Fluid Working Pressure
25D543
Low Pressure Remote Mix Manifold
300 psi (2.1 Mpa, 21 bar)
25D605
High Pressure Remote Mix Manifold
1500 psi (10.5 Mpa, 105 bar)
NOTE: This configuration will require installation
of a second solvent flow switch kit (24T787), sold
separately. A Dual Panel system will require two
solvent flow switch kits.
4. Select a Spray Gun
Spray Guns
Select a spray gun from the following table.
Application
Gun Model
Gun Manual No.
Maximum Fluid Working
Pressure
Conventional Air Spray
AirPro
312414
300 psi (2.1 MPa, 21 bar)
Electrostatic Air Spray
Pro Xp
3A2494
100 psi (0.7 MPa, 7 bar)
Conventional
Air-Assisted Spray
G15
3A0149
1500 psi (10.5 MPa, 105
bar)
Electrostatic Air-Assisted
Spray
Pro Xp AA
3A2495
3000 psi (21 MPa, 210
bar)
332457K
21
Configuring Your System
5. Select Color and Catalyst Change Control Module Kits
Using the following tables, choose color/catalyst
change control module kits that meet your
application’s requirements. The kits include a control
module with solenoid valves. See the Color Change
Kits and Color Change and Remote Mix Manifold
Kits manuals in Related Manuals, page 2 , for more
information.
If your application requires remote color change and
the control modules be mounted in the hazardous
location. See the Color Change and Remote Mix
Manifold Kits manual in Related Manuals, page 2 ,
for legacy kits that include IS-approved control
modules.
NOTE: All Color/Catalyst Control Module kits are to
be mounted outside of the hazardous location only.
Table 1 Color/Catalyst Change Control Kits (300 psi [2.068 MPa, 20.68 bar])
Kit Part No.
Kit Description
Kit Part No.
Kit Description
25D328
Control module with 4
solenoids
25D480
Control module with 12
solenoids
25D329
Control module with 5
solenoids
25D481
Control module with 13
solenoids
25D474
Control module with 6
solenoids
25D482
Control module with 14
solenoids
25D475
Control module with 7
solenoids
25D483
Control module with 15
solenoids
25D476
Control module with 8
solenoids
25D484
Control module with 16
solenoids
25D477
Control module with 9
solenoids
25D485
Control module with 17
solenoids
25D478
Control module with 10
solenoids
25D486
Control module with 18
solenoids
25D479
Control module with 11
solenoids
22
332457K
Configuring Your System
6. Select Color and Catalyst Change Manifold Kits
Using the following tables, choose color/catalyst
change control manifold kits that meet your
application’s requirements. The kits include a
manifold with valves. See the Color Change Kits and
Color Change and Remote Mix Manifold Kits manuals
in Related Manuals, page 2 , for more information.
Table 2 Low Pressure Color/Catalyst Change Manifold
Kit Part No.
Kit Description
Kit Part No.
Non--Circulating Kits
Low Pressure Pumps Non
Kit Description
Low Pressure Circulating Kits
24Y936
2 valve manifold
24Y937
2 valve manifold
24Y938
3 valve manifold
24Y939
3 valve manifold
24Y940
4 valve manifold
24Y941
4 valve manifold
24Y942
5 valve manifold
24Y943
5 valve manifold
24Y944
6 valve manifold
24Y945
6 valve manifold
24Y946
7 valve manifold
24Y947
7 valve manifold
24Y948
8 valve manifold
24Y949
8 valve manifold
24Y950
9 valve manifold
24Y951
9 valve manifold
24Y952
10 valve manifold
24Y953
10 valve manifold
26A272
11 valve manifold
26A273
11 valve manifold
26A274
12 valve manifold
26A275
12 valve manifold
26A286
13 valve manifold
25A605
13 valve manifold
26A276
14 valve manifold
26A277
14 valve manifold
26A278
15 valve manifold
26A279
15 valve manifold
26A280
16 valve manifold
26A281
16 valve manifold
26A282
17 valve manifold
26A283
17 valve manifold
26A284
18 valve manifold
26A285
18 valve manifold
332457K
23
Configuring Your System
Table 3 High Pressure Color/Catalyst Change Manifold
Kit Part No.
Kit Description
Non--Circulating Kits
High Pressure Pumps Non
Kit Part No.
Kit Description
24U182
3 valve manifold
24U183
4 valve manifold
24T647
2 valve manifold
24T648
3 valve manifold
24T649
4 valve manifold
24T677
2 valve manifold
24T650
5 valve manifold
24T678
3 valve manifold
24T651
6 valve manifold
24T679
4 valve manifold
24T652
7 valve manifold
24T680
5 valve manifold
24T653
8 valve manifold
24T681
6 valve manifold
24T654
9 valve manifold
24T682
7 valve manifold
24T655
10 valve manifold
24T683
8 valve manifold
24T656
11 valve manifold
24T684
9 valve manifold
24T657
12 valve manifold
24T685
10 valve manifold
24T658
13 valve manifold
24T686
11 valve manifold
24T659
14 valve manifold
24T687
12 valve manifold
24T660
15 valve manifold
24T688
13 valve manifold
24T661
16 valve manifold
24T689
14 valve manifold
24T662
17 valve manifold
24T690
15 valve manifold
24T663
18 valve manifold
24T691
16 valve manifold
Non-High Pressure Acid Compatible Non
Circulating Kits
24T692
17 valve manifold
24T693
18 valve manifold
24X360
24
High Pressure Circulating Kits
2 valve manifold
332457K
Configuring Your System
7. Select Pump Expansion Kits
8. Select Communication Options
NOTE: These are not required for Acid systems
which only use a single catalyst, or for Dual Panel
systems since they already include four pumps.
Use the following table to choose the appropriate
kit(s) to meet your system requirements.
The following table lists available kits to add a third
or fourth pump to your system. Each kit includes
one pump, a pump control module, solenoid,
frame, mounting bracket, and cabling. See the
Pump Expansion Kit manual (332456) for further
information.
Kit Part No.
Kit Description
24T805
AWI Kit for PD2K
15V337
AWI Module
NOTE: AWI is not currently available for Dual Panel
systems.
Kit Description
Low Pressure Pumps
(300 psi [2.068 MPa, 20.68 bar])
24R968
Low pressure resin
70cc pump
24R970
Low pressure catalyst
35cc pump
High Pressure Pumps (1500 psi [10.34
MPa, 103.4 bar])
24R969
High pressure resin
70cc pump
24R971
High pressure catalyst
35cc pump
332457K
Kit Part No.
9. Accessory Tool Kit
The following kit includes an assortment of tools for
maintenance and repair of the PD2K system.
Kit Part No.
Kit Description
25D980
PD2K Maintenance
Tool Kit
25
General Information
General Information
Location
• Reference numbers and letters in parentheses
in the text refer to numbers and letters in the
illustrations.
• Be sure all accessories are adequately sized and
pressure-rated to meet system requirements.
• To protect the screens from paints and solvents,
clear-plastic protective shields (10 per pack) are
available. Order Part No. 197902 for the Advanced
Display Module and Part No. 15M483 for the
Booth Control. Clean the screens with a dry cloth if
necessary.
To prevent tipping which can cause serious injury
and equipment damage, the mounting stand
must be securely anchored to the floor or to an
appropriate base. The stand is not intended for
free-standing use or wall mounting.
Mounting the PD2K Base Unit:
• Mount the PD2K in a non-hazardous location.
• Ensure that the mounting surface and mounting
hardware are strong enough to support the weight
of the equipment, fluid, hoses, and stress caused
during operation.
• Do not mount to a wall.
• Secure the stand to the floor with 1/2 in. (13 mm)
bolts which engage at least 6 in. (152 mm) into
the floor to prevent the unit from tipping. See
Dimensions, page 55.
• There must be sufficient space on all sides of
the equipment for installation, operator access,
maintenance, and air circulation. The fans at the
back of the unit require a minimum of 6 in. (152
mm) clearance from the closest surface to ensure
adequate air circulation.
Mounting the Booth Control:
Install the booth control in a hazardous area at a
convenient location for the operator to view and
operate. See Install the Booth Control, page 28.
26
332457K
Install the Display Module
Install the Display Module
1. Use the screws (11) to mount the bracket (10) for
the Advanced Display Module (12) on the front of
the Control Box or on the wall, as you prefer.
2. Snap the Advanced Display Module into the
bracket.
Figure 13 Advanced Display Module Connection
Ports
Figure 12 Install Display Module
3. Connect one end of the 5 ft (1.5 m) CAN cable
(provided) to the Advanced Display Module
(M). The other end of the cable comes from the
factory connected to the Enhanced Fluid Control
Module (EFCM).
Item
Description
J
Battery Cover
K
Model Number
L
USB Drive Interface
M
CAN Cable Connection
N
ADM Status LEDs
P
Accessory Cable Connection
R
Token Access Cover
NOTE: For a list of alternate cable lengths, see
Electrical Schematics, page 42. The total length of
all cable used in the system must not exceed 150
ft (45 m).
332457K
27
Install the Booth Control
Install the Booth Control
1. Use screws (S) to mount the bracket (10) for the
Booth Control (13) on the wall. Connect a ground
wire (G) to one of the screws. Connect the other
end of the ground wire to a true earth ground.
NOTE: A Dual Panel system has two Booth
Control modules, one for each mix unit. They
may be identified by a label on the rear denoting
them as “1” or “2”,
.
Figure 14 Ground the Booth Control Bracket
28
2. Snap the Booth Control into the bracket.
3. Connect the Booth Control to the Isolation Board
in the Electrical Control Box, using the 50 ft (15.2
m) intrinsically safe CAN cable (163).
NOTE: For a list of alternate cable lengths, see
Electrical Schematics, page 42. The total length
of cable used in the hazardous location must not
exceed 120 ft (36 m). The total length of all cable
used in the system must not exceed 150 ft (45 m).
Figure 15 Install the Booth Control
332457K
Air Supply
Air Supply
Air Requirements
• Compressed air supply pressure: 85-100 psi
(0.6–0.7 MPa, 6.0-7.0 bar).
• Air hoses: use grounded hoses that are correctly
sized for your system.
Trapped air can cause a pump or dispense
valve to cycle unexpectedly, which could result
in serious injury from splashing or moving parts.
Use bleed-type shutoff valves.
• Air regulator and bleed-type shutoff valve: include
in each air line to fluid supply equipment. Install
an additional shutoff valve upstream of all air line
accessories to isolate them for servicing.
332457K
To reduce the risk of fire and explosion if using
a Graco electrostatic gun, a shutoff valve must
be installed in the gun air line to shutoff the
atomizing and turbine air to the gun. Contact
your Graco distributor for information on air
shutoff valves for electrostatic applications.
• Air Line Filter for System Control Air: Use supplied
air regulator/filter 17M842 to provide clean and dry
air to system control solenoids.
• Air Line Filter for Atomizing Air: Provided by others
to filter oil and water out of the air supply and help
avoid paint contamination.
See Technical Data, page 56, for air filtration
requirements.
29
Air Supply
Air Connections
1. Tighten all system air and fluid line connections
as they may have loosened during shipment.
2. Connect the main air supply line to air
regulator/filter 17M842, and then to the main air
inlet (136). This air line supplies the solenoids,
valves, and pumps. Do not use this line to supply
the gun’s atomizing air.
3. Connect a separate, dedicated, clean air supply
line to the air inlet (159a) of the air flow switch.
This air supplies gun atomizing air. The air flow
switch detects air flow to the gun and signals the
controller when the gun is being triggered.
NOTE: For Dual Panel systems, the guns’
atomizing air is connected at the Air Control
Module (see manual 3A4497).
NOTE: If you are using a Graco hose bundle,
connect the 4 ft (1.2 m) end of the air hose to the
atomizing air outlet (159c) and the 7 ft (2.1m) end
of the air hose to the gun. If there is more than
one gun (for example, a separate gun for each
color), the atomizing air outlet (159c) must be
branched to each gun. For ease of maintenance,
install a ball valve at all air line tees.
Figure 17 Air Manifold Connections
Key
Connection
Description
A
Air inlet
C
GFB/Air cutoff output (plugged)
/ Solvent cutoff output 2 (Dual
Panel)
M
Exhaust muffler
S
Solvent cutoff output
Figure 16 Connect Atomizing Air
30
332457K
Fluid Supply
Fluid Supply
Fluid Requirements
• Materials can be transferred from their original
containers or from a central paint recirculating line.
• Install a 100 mesh (minimum) fluid filter in the fluid
supply line, with a drain valve.
• To reduce the risk of equipment
overpressurization and rupture which can
cause injury, including skin injection, do not
exceed the pressure rating of the lowest rated
system component. See the identification
label for the maximum working pressure of the
equipment.
• To reduce the risk of injury, including skin
injection, you must install a shutoff valve
between each fluid supply line and the mix
manifold. Use the valves to shut off fluid during
maintenance and service.
Models are available to operate air spray (300 psi) or
air-assisted (1500 psi) systems with a capacity of up
to 800 cc/minute (depending on material viscosity).
• Fluid supply pressure tanks, feed pumps, or
circulating systems can be used to supply fluid to
the system.
332457K
NOTE: The fluid supply must be free of pressure
spikes, which are commonly caused by pump stroke
changeover. Read the supply pressure on the gauge
(P). Supply pressure must be as close as possible
to the pressure setpoint:
• For low pressure systems, ± 100 psi (0.7 MPa, 7
bar) of setpoint.
NOTE: For low pressure systems, it is
recommended the supply pressure be maintained
between 1/2 to 2/3 of the system operating spray
pressure.
• For high pressure systems, ± 300 psi (2.1 MPa,
21 bar) of setpoint.
If necessary, install pressure regulators or a surge
tank on the pump fluid inlet lines to reduce pulsation.
Contact your Graco distributor for additional
information.
31
Fluid Supply
Single Color Connections
Color Change Connections
NOTE: Check valves (J, L) are provided on the inlet
and outlet manifolds of each pump.
If you are installing the color change accessory kit,
make the fluid connections as described in manual
332455.
1. Connect the color supply line to the pump fluid
inlet fitting (S).
2. Connect the color outlet line to the pump fluid
outlet fitting (R).
3. Make the same connections on the catalyst side.
NOTE: For isocyanate catalyst materials, moisture
resistant hose is required to supply fluid to the system
and also as a fluid line between the pump and the
mix manifold.
Solvent Connections
1. Connect the solvent supply line to the cutoff
valve inlet fitting (FI).
2. Connect the solvent outlet line to the solvent flow
switch outlet fitting (FO).
For Dual Panel Systems
Dual panel systems have two flow switches (FS1 and
FS3) with the inlet fittings (FI) and outlet fittings (FO)
arranged vertically, as shown below. The procedure
for connecting the solvent supply lines is the same
as the previous steps, repeated for each flow switch
(FS1 and FS3).
Figure 18 Pump Inlet and Outlet Connections
32
332457K
TSL Cup Kit
TSL Cup Kit
The cup is used for either Throat Seal Liquid (TSL)
or ISO oil. These liquids prevent exposure of air or
moisture with the resin or catalyst at the pump throat
packings and dosing valves. The PD2K Proportioner
includes two TSL Cup Kits, one for each pump. The
cups supply TSL to the upper throat cartridge of the
color (70 cc) pump, to the upper and lower throat
cartridges of the catalyst (35 cc) pump, and to the
four pump dosing valves. When using isocyanate
catalysts, the cup attached to the catalyst side of the
PD2K Proportioner is used to supply ISO oil to the
upper and lower throat cartridges of the catalyst (35
cc) pump and the catalyst dosing valves.
2. Place the TSL cup (73) into the bracket (73a).
NOTE: TSL and ISO oil must be ordered separately.
For TSL, order Part No. 206995, one quart (0.95
liter). For ISO oil, order Part No. 217374, one pint
(0.48 liter).
1. Slide the kit mounting bracket onto any side of
the pump’s hex nut.
Figure 19 Install TSL Cup Kit
NOTE: Prior to mounting the cup, use a
permanent black marker to mark a horizontal line
on the front of the cup approximately half way
between the top and bottom of the cup. Mark a
second horizontal line approximately 1/4 in. (3
mm) above the first line. Shining a strong light
towards these lines will provide a shadow that
will be visible from inside the TSL cup.
332457K
NOTE: The pump’s upper throat cartridge has
three ports (two are plugged). Move a plug (73d)
if necessary so the barbed fitting (73b) can be
put in the port closest to the TSL cup.
3. Check that the o-ring is in place on the barbed
fitting (73b). Apply low strength thread adhesive
and install the fitting in the upper throat cartridge
port. Be sure the other two ports are plugged
(73d).
33
TSL Cup Kit
4.
Repeat for the lower throat cartridge.
NOTE: If you are not lubricating the dosing
valves, remove the unused barbed fittings (73b)
from the bottom of the TSL cup (73). Apply low
strength thread adhesive and install the plugs
and gaskets supplied with the kit.
2. Cut the tubing (73c) to length as required.
Connect the TSL cup fittings to the fittings on the
pump and valves. TSL is gravity-fed from the
cup to the pump and valves; position the fittings
and tubing to prevent kinks and enable the TSL
to flow freely down to the valve and air to rise
up and out of the valve.
1. If you are lubricating the dosing valves, remove
the plug (73d) and gasket from the valve port (V)
closest to the TSL cup.
NOTE: Choose the valve port in the upward
facing position. This will allow liquid to flow into
the valve while allowing air to rise out of the
valve.
Check that the o-ring is in place on the barbed
fitting (73b). Apply low strength thread adhesive
and install the fitting in the valve port (V).
NOTE: Do not confuse the valve port (V) with the
air port (W).
3. Fill the cup to the level of the lower black
horizontal line with either TSL or ISO oil, as
appropriate for the resin and catalyst materials
being used.
NOTE: If TSL leaks from the rod guard of the
color (70 cc) pump, be sure the lower u-cup seal
is installed in the lower throat cartridge.
NOTE: The fluid levels in the TSL cups should be
checked daily. Fluid levels should remain static
for an extended period of time. Rising or falling
fluid levels in a TSL cup can be an indication of a
condition which needs immediate attention. Refer
to the troubleshooting steps in the repair manual for
guidance.
34
332457K
TSL Cup Kit
ISO Oil Fill Procedure
When using polyurethane coatings with isocyanate
catalysts in high-humidity environments, use of ISO
oil on the catalyst pump TSL cup is recommended
instead of TSL. The ISO oil will present a barrier
that will prevent catalyst hardening from contact with
moisture. When performing the first fill of a cup with
ISO oil, it will be necessary to bleed the air out of the
feed line.
NOTE: If not already present on the TSL cup, draw
the two horizontal lines at, and slightly above, the
vertical center of the front of the cup before filling.
To bleed air:
1. Fill the catalyst pump TSL cup to the lower
horizontal line.
2. Remove one plug (73d) from the upper throat
cartridge and allow air in that area to flow until no
air is being expelled. Replace the plug.
3. Repeat step 2 at the lower throat cartridge.
4. Use absorbent rags to clean up excess ISO oil
that escaped from the plug holes.
5. Replenish the ISO oil level in the TSL cup to the
lower horizontal line.
332457K
Alternate TSL Plumbing for
Highly--Reactive/Moisture
Reactive/Moisture--Sensitive
Highly
ISO Catalyst PD2K Pumps
NOTE: Graco recommends this alternate TSL (Throat
Seal Liquid) plumbing installation only on Catalyst
pumps, as the open rod guard of resin pumps does
not generate TSL displacement.
The alternate TSL plumbing of the Catalyst pump
allows TSL to flow through the upper seal and
bearing cartridge by using the rod guard and
lower-rod displacement. This flow purges isocyanateand moisture- contaminated TSL from the throat
area; preventing the crystallization reaction of the
isocyanate and moisture from accumulating and
damaging the pump seals, displacement rod, and
bearings.
1. Replace a plug (73d) with a barbed fitting (73b)
on a second port of the pump’s upper throat
cartridge (only one will be plugged). Check that
the o-ring is in place on the barbed fitting (73b).
Apply low-strength thread adhesive and install
the fitting in the upper throat cartridge port. Be
sure the third port is plugged (73d).
35
TSL Cup Kit
2. Connect the tubing (73c1) from the barbed fitting
(73b) on the lower throat cartridge to one of
the barbed fittings (73b) on the upper throat
cartridge.** Connect tubing (73c2) from the other
barbed fitting (73b) on the upper throat cartridge
to a TSL cup fitting.
Additional Maintenance and Precautions
The TSL fluid in the TSL reservoir must be replaced
more frequently when the alternate TSL plumbing
is used. This requirement prevents contaminated
TSL from accumulating in the reservoir, causing
fluid line contamination and increased pressure in
the TSL tubes due to thickening viscosity. The TSL
replacement frequency is determined by a number of
factors: Catalyst reactivity, temperature and humidity
of the pump environment, and seal wear condition.
In severe environmental conditions, the TSL can
require weekly replacement.
Another maintenance procedure that extends pump
life is bleeding the fresh TSL into the rod guard during
TSL replacement. This bleed process ensures that
all of the air is removed from the guard and bearing
cartridge, eliminating wet air contamination during
the TSL replacement process.
1. Remove and thoroughly clean the rod guard.
2. Refill the rod guard with fresh TSL.
3. Place the rod guard over the rod.
4. Fill the Reservoir, and let gravity fill the TSL lines.
5. Thread the guard back on to the pump when the
TSL begins to overflow the guard.
NOTICE
The rod guard displacement-flow volume through
the bearing and barb fittings of the upper cartridge
during high-cycle rates of the pump, or from filling
and the color change process, can create fluid
pressure in the TSL line between the pump’s lower
and upper cartridges. Route and anchor the TSL
lines to prevent equipment damage if the lines
develop leaks or separate from a barb fitting.
* No additional fittings or tubing are needed for
the alternate TSL plumbing if the barb fitting (73b)
from the TSL (73) and the second plug (73d)
from the throat cartridge are used by swapping
their positions.
36
NOTICE
The TSL lines are flexible, clear, and compatible
with TSL. These features make installation
much easier, and allow for visual feedback of
the TSL condition. The TSL tubing should be
replaced to prevent equipment damage from
tubing fluid compatibility failure if the lines become
contaminated with catalyst material for extended
periods of time.
332457K
Solvent Meter Accessory
Solvent Meter Accessory
To install Solvent Meter Kit 280555, see manual
308778.
NOTE: Install the solvent meter downstream of the
solvent cutoff switch near the base unit.
Light Tower Accessory
Electrostatic Air Hose
Quick Disconnect Kit
24S004
NOTE: To use a quick disconnect on an existing
electrostatic air hose, order Part No. 24S004 Kit. You
will also need to order Part No. 24U059 Electrostatic
Air Whip Hose (6 ft) [1.8 m].
Install the kit as follows.
To install Light Tower Kit 24K337, see manual
3A1906.
1. Connect the quick disconnect (QD) to the existing
electrostatic air hose (P). The quick disconnect is
a 1/4 npsm(m) left-hand thread.
2. Screw the female end of adapter fitting (QF) onto
the quick disconnect (QD).
3. Screw the 24U059 Electrostatic Air Whip Hose
(WH) onto the male end of the adapter fitting
(QF).
NOTE: Make the following ground connections
to ensure air hose grounding continuity in the
electrostatic system.
4. Connect the ground wire (PG) of the existing
electrostatic air hose (P) to a true earth ground.
5. Connect the whip hose ground wire (WG) to
the green ground lug (GND) of the mix manifold
(M). Connect a ground wire (MG) from the mix
manifold ground lug to a true earth ground.
Figure 20 Electrostatic Air Hose Quick Disconnect Kit
332457K
37
Electrical Supply
Electrical Supply
Electrical Connections
See Electrical Schematics, page 42.
Improper wiring may cause electric shock or other
serious injury if work is not performed properly. All
electrical wiring must be completed by a qualified
electrician and comply with all local codes and
regulations.
Electrical Requirements
1. Verify that electrical power at the main panel is
shut off. Open the Control Box cover.
2. Thread the electrical cord wires through the
strain relief (S).
3. Connect the wires (L, N, G) securely to the
corresponding terminals of the terminal block (T),
as shown.
4. Tighten the strain relief nut securely.
5. Close the Control Box. Restore power.
Enclose all cables routed in the spray booth and high
traffic areas in conduit to prevent damage from paint,
solvent, and traffic.
The unit operates with 90-250 VAC, 50/60 Hz input
power, with a maximum of 7 A current draw. The
power supply circuit must be protected with a 15 A
maximum circuit breaker.
• A power supply cord compatible to your local
power configuration is not included. Wire gauge
size must be 8-14 AWG.
6. Follow instructions in Grounding, page 39.
Wire Key
Wire
Description
L
Line Power
N
Neutral
G
Ground
• The input power access port is 22.4 mm (0.88
in.) in diameter. A strain relief is provided which
accepts a cord diameter of 0.157–0.354 in. (4–9
mm). If another cord size is used, a user-supplied,
appropriate size strain relief must be installed.
Figure 21 Control Box Electrical Connection
38
332457K
Grounding
Grounding
Booth Control
The booth control is grounded through intrinsically
safe cable connections to the electrical control box.
This equipment must be grounded to reduce the
risk of static sparking and electric shock. Electric
or static sparking can cause fumes to ignite or
explode. Improper grounding can cause electric
shock. Grounding provides an escape wire for the
electric current.
Attach a separate ground wire to the
booth control mounting bracket. See
Install the Booth Control, page 28.
Color Change Module
Electrical Control Box
Connect a ground wire from the color change module
to a true earth ground.
The electrical control box has two ground points.
Both connections must be made.
Intrinsically safe color change modules located in the
hazardous area must be connected to a true earth
ground in the hazardous area.
• Connect the ground wire (Y) to the ground screw
on the electrical control box. Connect the clamp
end to a true earth ground.
Feed Pumps or Pressure Pots
• The power supply must be grounded according to
local codes. Connect the power supply ground
wire to the Ground terminal in the electrical control
box. See Electrical Connections, page 38.
Connect a ground wire and clamp from a true earth
ground to the pumps or pots. See pump or pressure
pot manual.
Air and Fluid Hoses
Use grounded hoses only.
Spray Gun
Follow the grounding instructions in your gun manual.
• Non-Electrostatic: Ground the spray gun through
connection to a Graco-approved grounded fluid
supply hose.
• Electrostatic: Ground the spray gun through
connection to a Graco-approved grounded air
supply hose. Connect the air hose ground wire to
a true earth ground.
Figure 22 Ground Screw and Power Switch
Fluid Supply Container
Follow local code.
332457K
39
Grounding
HAZARDOUS LOCATION
NON--HAZARDOUS LOCATION
NON
Figure 23 System Grounding
Key
1
Electrical Control Box ground screw
2
Electrical Control Box ground wire
3
Color Change Module (CC) ground wires
4
Intrinsically Safe (IS) cable
40
5
True Earth Ground; check local code for
requirements
6
Non-Intrinsically Safe cable
7
Booth Control (BC) mounting bracket
ground wire
332457K
Grounding
Object Being Sprayed
Check Resistance
Follow local code.
All Solvent Pails Used When Purging
Follow local code. Use only conductive metal
pails/containers placed on a grounded surface. Do
not place the pail/container on a nonconductive
surface, such as paper or cardboard, which interrupts
the grounding continuity.
332457K
To ensure proper grounding, resistance between
components and true earth ground must be less
than 1 ohm.
41
Electrical Schematics
Electrical Schematics
Standard Models (MC1000, MC2000, MC3000, MC4000)
NOTE: The electrical schematic illustrates all possible
wiring expansions in a ProMix PD2K system; models
MC1000, MC2000, and MC4000. Some components
shown are not included with all systems.
NOTE: See Optional Cables and Modules, page 54 for
a list of cable options.
CABLE
16H078
AWI
GATEWAY
(24R910)
2
CABLE
(15V206)
CATALYST CHANGE
MODULE 6
6
(24N935)
CATALYST CHANGE
MODULE 5
6
(24N935)
COLOR CHANGE
MODULE 4
6
(24N935)
COLOR CHANGE
MODULE 3
6
(24N935)
2
CABLE
(15V206)
2
CABLE
(15V206)
MAC SERIES 46
SOLENOID
(16P812)
PUMP V/P FOR
FLUID REG.
UP
DOWN
FLOW SENSOR
(120278)
OR G3000 METER
(239716, 258718
16M510, 16M519)
PUMP INLET
TRANSDUCER
(16P289, 16P290)
PUMP OUTLET
TRANSDUCER
(16P289, 16P290)
PUMP V/P FOR
FLUID REG.
MAC SERIES 46
SOLENOID
(16P812)
PUMP OUTLET
TRANSDUCER
(16P289, 16P290)
BREAKOUT MODULE PUMP 3
(24N527)
PUMP INLET
TRANSDUCER
(16P289, 16P290)
UP
DOWN
FLOW SENSOR
(120278)
OR G3000 METER
(239716, 258718
16M510, 16M519)
SOLVENT METER (258718)
SAFETYINTERLOCK SWITC
H
CABLE (16V429)
COLOR CH
ANGE MODULE 7
(24R219)
7
1 CABLE
(16V426)
1
LIGHT
TOWER
(15X472)
1
CABLE
(16T280)
CABLE (16T659)
CABLE (16T659)
CABLE (16T659)
CABLE (16T659)
SOLVENT
FLOW
INPUTS
SWITCH (120278)
3
ADVANCED
CABLE
DISPLAY MODULE
(121003)
(24E451)
4
FAN
(24P658)
ENCODERAND MOT
OR
(16P036, 16P037)
WIRE HARNESS
(24P684, 24P685)
SOLVENTCUTOFF (121324)
SWITCH (120278)
FLOW RATE ANALOG IN
FLOW SENSOR
(120278)
OR G3000 METER
(239716, 258718
16M510, 16M519)
FAN
(24P658)
ENCODER AND MOT
OR
(16P036, 16P037)
WIRE HARNESS
(24P684, 24P685)
UP
DOWN
BARRIER
BOARD
(248192)
GFB
INTERF
ACES
PRESSURE SW (121323)
GCA
MODULE
EFCM
(24N913)
FLOW RATE ANALOG IN
FLOW SENSOR
(120278)
OR G3000 METER
(239716, 258718
16M510, 16M519)
PUMP V/P FOR
FLUID REG.
SPLITTER
(16P243)
SOLENOID (121324)
FLOW RATE ANALOG IN
UP
DOWN
PUMP OUTLET
TRANSDUCER
(16P289, 16P290)
BREAKOUT MODULE PUMP 2
(24N527)
MAC SERIES 46
SOLENOID
(16P812)
PUMP V/P FOR
FLUID REG.
PUMP INLET
TRANSDUCER
(16P289, 16P290)
COLOR CH
ANGE MODULE 8
(24R219)
7
BOOTH CO
NTROL(24M731)
BREAKOUT MODULE PUMP 4
(24N527)
PUMP OUTLET
TRANSDUCER
(16P289, 16P290)
ENCODERAND MOT
OR
(16P036, 16P037)
WIRE HARNESS
(24P684, 24P685)
MAC SERIES 46
SOLENOID
(16P812)
PUMP INLET
TRANSDUCER
(16P289, 16P290)
FAN
(24P658)
BREAKOUT MODULE PUMP 1
(24N527)
ENCODER AND MOT
OR
(16P036, 16P037)
WIRE HARNESS
(24P684, 24P685)
119159
119159
119159
119159
16T072
CAN
IS BOARD
(24M485)
FAN
(24P658)
GUNTRIGGER INPUTS
CABLE
(16V426)
16W159
16W159
POWER IN
16W159
16W159
TERMINAL
BLOCKS WITH FUSES
FLOW RATE ANALOG IN
TERMINAL BLOCK
(114095)
3 CABLE
(121227)
2
5
COLOR CHANGE
MODULE 2
6
(24N935)
48V-10APOWER SUPPLY
(16U820)
3 CABLE
(121001)
5
24V
POWER
SUPPLY
(16T660)
3
CABLE
(121227)
LINEFILTER
(16V446)
INTEGRA
TION
GATEWAY
CABLE (15V206)
CABLE
16T658
COLOR CHANGE
MODULE 1
6
(24N935)
POWER MODULE
(24R257)
2 CABLE
(15V206)
2 CABLE
(15V206)
065161, 065159
RELAY
2 POSITION
SWITCH
(16U725)
HAZARDOUS LOCATION
NON-HAZARDOUS LOCATION
Figure 24 Electrical Schematic, Sheet 1
42
332457K
Electrical Schematics
CONTINUED ON P
AGE 3
CONTINUED ON P
AGE 3
UNUSED
UNUSED
5
4
3
2
1
10
1
2
3
4
5
8
1
2
3
4
5
6
7
8
9
10
11
12
5
AWI
GATEWAY
(24R910)
12345
CAN IS BOARD
(NONIS)
(IS)
4
1
2
3
4
5
1
2
3
4
5
(121227)
P3
P4
3
GCAMODULE
EFCM
(24N913)
3
5
12345
1
2
3
UNUSED
54 3 2 1
SOLVENT CUTOFF (121324)
PWR (RED)
SIG (WHITE)
COM(BLACK)
SHIELD/GRN
SOLVENT
UNUSED
BARRIER
BOARD
(248192)
+24VDC
COM
UNUSED
UNUSED
+24VDC
COM
+24VDC
COM
UNUSED
1
RED WIRE (06
5161)
2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
METER
(258718)
GROUND BAR
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
4 25 PIN
D-SUB CABLE
(16T659)
UNUSED
UNUSED
CABLE
(16T280)
GFB INTERFACE
(121324)
123
UNUSED
UNUSED
(121001)
3
(24M485)
12345
SPLITTER
(16P243)
1
2
3
4
5
INTEGR
ATION
GATEWAY
5
1
CABLE
4
25 PIN D-SUB CABLE
(16T659)
BLAC
K WIRE (065159)
24V
POWER
SUPPLY
(16T660)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
1
1
GRND (GRN/YEL)
3
2
12345
1234
4
BREAK
OUT MODULE PUMP 2 (24N527)
7
6
5
12345
12345
1234
13 A1(+) A2(-)
8
12 34
12 34
5678
7
6
5
12345
1234
12 3 4
8
12 34
5678
+24VDC
COM
+24VDC
COM
PUMP 2
UP
PUMP 2
DOWN
MANIFOLD
MAC SERIES 46
(16P812 QTY 2)
+-+-+-+-
LINE
FILTER
(16V446)
V/P FOR FLUID REG.
PUMP 2
OUTLET TRANSDUCER
PUMP 2
(16P289 OR 16P290)
SEE DET
AILAOR B
INLET TRANSDUCER
PUMP 2
(16P289 OR 16P290)
FAN PUMP 1
(24P658)
PWR (RED)
SIG (WHITE)
COM(BLACK)
SHIELD/GRN
+24VDC
COM
+24VDC
COM
PUMP 1
UP
ENCODER/MO
TOR
AND
WIRE HARN
ESS
PUMP2
MANIF
OLD
MAC SERIES 46
(16P812 QTY 2)
F2
F1
F4
N
F3
+-+-+-+-
POWER MODULE
(24R257)
N04
4
12345
PUMP 1
DOWN
SEE DET
AILAOR B
V/P FOR FLUID REG.
PUMP 1
+ -
CABLE
(16T658)
L
ENCODER/MOT
OR
AND
WIRE HARN
ESS
PUMP1
N03
2 POSITION
SWITCH
(16U725)
N04
INLET TRANSDUCER
PUMP 1
(16P289 OR 16P290)
48V-10A
POWER SUPPLY
(16U820)
N (BLUE)
L (BROWN)
N03
GRND
OUTLET TRANSDUCER
PUMP 1
(16P289 OR 16P290)
14
N L
3
1234
+48V
COM
+48V
COM
RELAY
2
12345
+48V
COM
+48V
COM
BREAK
OUT MODULE PUMP 1 (24N527)
PWR (RED)
SIG (WHITE)
COM(BLACK)
SHIELD/GRN
2
P4
P3
16T072
12345
1
1
2
3
4
5
CABLE
G3000
METER
PUMP 1
(EITHER, 239716,
258718,16M510,
OR 16M519)
GRND
SCREW
TWIST
ED PAIR CABLE (16W159)
G3000
METER
PUMP 2
(EITHER, 239716,
258718,16M510,
OR 16M519)
GRND
SCREW
TWIST
ED PAIR CABLE (16W159)
L GRND N
MOTOR
MOUNTING
SCREW
1 2 3 4 5 6 78 9
1011 12
WIRE HARN
ESS
(24P685)
1 2 3 4 5 6 78 9
12
10
PUMP ENCODER AND MOTOR
(16P037)
1 2 3 4 5 67 8 9
MOTOR
MOUNTING
SCREW
1011 12
UNUSED
UNUSED
UNUSED
DRAIN/FOIL
UNUSED
DRAIN/FOIL
UNUSED
UNUSED
DRAIN/FOIL
UNUSED
UNUSED
UNUSED
UNUSED
DRAIN/FOIL
DRAIN/FOIL
MOTOR
GROUND
SCREW
UNUSED
UNUSED
UNUSED
UNUSED
WIRE HARN
ESS
(24P684)
L N GRND
3
1234
1 2 3 4 5 67 8 9
UNUSED
UNUSED
12345
1234
UNUSED
UNUSED
12345
BREAKOUT MODULE
(24N527)
2
3
UNUSED
UNUSED
UNUSED
2
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
BREAKOUT MODULE
(24N527)
TERMINAL
BLOCK
(114095)
UNUSED
L N GRND
POWER IN
DETAIL B, HIGH PRESSURE PUMPS
(24M707, 24M71
5, 24T800)
DETAILA, LOW PRESSURE PUMPS
(24M706, 24M714, 24T799)
UNUSED
CABLE
(16H078)
10
PUMP ENCODER AND MOTOR
(16P036)
Figure 25 Electrical Schematic, Sheet 2, Part 1
CONTINUED ON THE NEXT PAGE
332457K
43
FAN PUMP 2
(24P658)
3
CABLE
(15V206)
CABLE (16V429)
2
UNUSED
CABLE (121227)
Electrical Schematics
GUN TRIGGER INPUTS
SIG
COM
SIG
COM
SIG
COM
SIG
COM
SIG
COM
SIG
COM
7
1
2
3
4
5
6
7
8
9
10
11
12
FLOW RATE ANALOG IN 1
FLOW RATE ANALOG COMMON 1
FLOW RATE ANALOG IN 2
FLOW RATE ANALOG COMMON 2
FLOW RATE ANALOG IN 3
FLOW RATE ANALOG COMMON 3
FLOW RATE ANALOG IN 4
FLOW RATE ANALOG COMMON 4
SIG
SOLVENT FLOW SWITCH 2 (120278)
COM
SIG
SAFETY INTERLOCK SWITCH
COM
9
1
2
3
4
5
6
GCAMODULE
EFCM
(24N913)
3
4
1
3
LIGHT
TOWER
(15X472)
3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
1
BREAKOUT MODULE PUMP 3 (24N527)
4
12345
7
6
5
12345
1234
12 34
8
12 34
5678
2
3
12345
1234
BREAKOUT MODULE PUMP 4 (24N527)
4
12345
5
12345
7
6
1234
12 34
8
12 34
5678
FAN PUMP 4
(24P658)
PWR (RED)
SIG (WHITE)
COM(BLACK)
SHIELD/GRN
+24VDC
COM
+24VDC
COM
PUMP 4
UP
MANIFOLD
MAC SERIES 46
(16P812 QTY 2)
MAC SERIES 46
(16P812 QTY 2)
MANIFOLD
PUMP 4
DOWN
V/P FOR FLUID REG.
PUMP 4
OUTLET TRANSDUCER
PUMP 4
(16P289 OR 16P290)
SEE DETAILAOR B
INLET TRANSDUCER
PUMP 4
(16P289 OR 16P290)
FAN PUMP 3
(24P658)
PWR (RED)
SIG (WHITE)
COM(BLACK)
SHIELD/GRN
+24VDC
COM
+24VDC
COM
PUMP 3
UP
ENCODER/MOTOR
AND
WIRE HARNESS
PUMP 4
PUMP 3
DOWN
V/P FOR FLUID REG.
PUMP 3
SEE DETAILAOR B
OUTLET TRANSDUCER
PUMP 3
(16P289 OR 16P290)
ENCODER/MOTOR
AND
WIRE HARNESS
PUMP 3
INLET TRANSDUCER
PUMP 3
(16P289 OR 16P290)
+48V
COM
+48V
COM
1234
1
2
3
4
5
ADVANCED
DISPLAY MODULE
(24E451)
+48V
COM
+48V
COM
2
(121003)
1
2
3
4
5
4
25 PIN D-SUB CABLE
(16T659)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
12345
GFB PRESSURE SWITCH (121323)
SOLVENT FLOW SWITCH 1 (120278)
CABLE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
4 25 PIN
D-SUB CABLE
(16T659)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
119159
1
2
3
4
5
6
7
8
9
10
11
12
G3000
METER
PUMP 3
(EITHER, 239716,
258718,16M510,
OR 16M519)
GRND
SCREW
G3000
METER
PUMP 4
(EITHER, 239716,
258718,16M510,
OR 16M519)
GRND
SCREW
TWISTED PAIR CABLE (16W159)
TWISTED PAIR CABLE (16W159)
Figure 26 Electrical Schematic, Sheet 2, Part 2
CONTINUED ON THE NEXT PAGE
44
332457K
Electrical Schematics
FROMCAN IS BOARD (24M485)
2 CABLE(15V206)
12 34 5
COLOR
CHANGE
MODULE 1
(COLORS
1 THRU 8)
MANIFOLD
FLUSH
COLOR1
COLOR2
COLOR3
COLOR4
COLOR5
COLOR6
COLOR7
COLOR8
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
J8
MANIFOLD
J9
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
J16
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
J10
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
6
J15
J14
DUMP
COLOR1
COLOR2
COLOR3
COLOR4
COLOR5
COLOR6
COLOR7
COLOR8
MANIFOLD
*FLUSH
COLOR9
COLOR10
COLOR11
COLOR12
COLOR13
COLOR14
COLOR15
COLOR16
12 34 5
COLOR
CHANGE
MODULE 2
(COLORS
9 THRU 16)
1
2
3
4
5
6
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3 J15
4
5
6
J16
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
J10
J9
J8
6
J14
MANIFOLD
MANIFOLD
+24VDC
COM
+24VDC
COM
+24VDC
COM
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
DUMP*
FLUSH
COLOR9
CATALYST 1
COLOR10
CATALYST 2
COLOR11
CATALYST 3
COLOR12
CATALYST 4
COLOR13
COLOR14
COLOR15
COLOR16
CATALYST
CHANGE
MODULE 5
(CATALYST
1 THRU 4)
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
J8
+24VDC
COM
+24VDC
COM
UNUSED
UNUSED
1
2
3
4
5
6
J15
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
1
2
3
4
5
6
J14
COLOR17
COLOR18
COLOR19
COLOR20
COLOR21
COLOR22
COLOR23
COLOR24
12 34 5
COLOR
CHANGE
MODULE 3
(COLORS
17 THRU 24)
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
J8
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
J15
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
J9
6
J14
J16
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
UNUSED
UNUSED
J10
6
5
4
3
2
1
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
J9
DUMP
CATALYST 1
CATALYST 2
CATALYST 3
CATALYST 4
12 34 5
2
MANIFOLD
MANIFOLD
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
6
5
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
J16 43
J10
CABLE
(15V206)
2
CABLE
MANIFOLD
COM
+24VDC
COM
+24VDC
COM
+24VDC
6
12 34 5
*FLUSH
MANIFOLD
6
5
4
3
2
1
*FLUSH
DUMP*
COLOR17
COLOR25
COLOR18
COLOR26
COLOR19
COLOR27
COLOR20
COLOR28
COLOR21
COLOR29
COLOR22
COLOR30
COLOR23
COLOR24
54 3 2 1
(15V206)
2
CABLE
(15V206)
12 34 5
12 34 5
COLOR
CHANGE
MODULE 4
(COLORS
25 THRU 32)
+24VDC
COM
+24VDC
COM
+12VDC
COM
1
2
3
4
5
6
J8
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
J15
+24VDC
COM
UNUSED
UNUSED
UNUSED
UNUSED
1
2
3
4
5
6
COM
+24VDC
COM
+24VDC
COM
+24VDC
J16
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
J10
6
5
4
3
2
1
COM
+24VDC
UNUSED
UNUSED
UNUSED
UNUSED
J9
6
J14
MANIFOLD
6
5
4
3
2
1
DUMP*
COLOR25
COLOR26
COLOR27
COLOR28
COLOR29
COLOR30
12 34 5
2
CABLE(15V206)
Figure 27 Electrical Schematic, Sheet 3
* May be unused in some configurations.
CONTINUED ON THE NEXT PAGE
332457K
45
Electrical Schematics
CATALYST
CHANGE
MODULE 6
(CATALYST
3 THRU 4)
MANIFOLD
FLUSH
CATALYST 3
CATALYST 4
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
1
2
3
4
5
6
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
1
2
3
4
5
6
J8
MANIFOLD
J9
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
J16
6
5
4
3
2
1
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
J10
6
5
4
3
2
1
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
J16
6
5
4
3
2
1
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
J10
6
5
4
3
2
1
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
6
J15
J14
DUMP
CATALYST 3
CATALYST 4
2
CABLE
(15V206)
12 34 5
54 3 2 1
CATALYST
CHANGE
MODULE 5
(CATALYST
1 THRU 2)
MANIFOLD
FLUSH
CATALYST 1
CATALYST 2
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
J8
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
1
2
3
4
5
6
J15
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
1
2
3
4
5
6
MANIFOLD
J9
6
J14
DUMP
CATALYST 1
CATALYST 2
(15V206)
2
CABLE
12 34 5
12 34 5
COLOR
CHANGE
MODULE 4
(COLORS
25 THRU 32
)
ALTERNATE CONFIGURATION
FOR CATALYST CHANGE CONTROL
Figure 28 Electrical Schematic, Sheet 3, Alternate
Configuration for Catalyst Change Control
CONTINUED ON THE NEXT PAGE
46
332457K
Electrical Schematics
FROMCAN IS BOARD (24M485)
NON-HAZARDOUS LOCATION
HAZARDOUS LOCATION
MANIFOLD
COLOR FLUSH
COLOR 1
COLOR 2
COLOR 3
COLOR 4
COLOR 5
COLOR 6
COLOR 7
COLOR 8
+12VDC
COM
+12VDC
COM
+12VDC
COM
1
2
3
4
5
6
+12VDC
COM
+12VDC
COM
+12VDC
COM
1
2
3
4
5
6
+12VDC
COM
+12VDC
COM
+12VDC
COM
1
2
3
4
5
6
12 34 5
COLOR
CHANG
E
MODULE 7
(COLORS
33 THRU 40)
J8
MANIFOLD
J9
6
5
4
3
2
1
COM
+12VDC
COM
+12VDC
COM
+12VDC
J16
6
5
4
3
2
1
COM
+12VDC
COM
+12VDC
COM
+12VDC
6
5
4
3
2
1
COM
+12VDC
COM
+12VDC
COM
+12VDC
7
J15
J14
J10
CATALYST FLUSH
CATALYST 1
CATALYST 2
CATALYST 3
CATALYST 4
COLOR 9
COLOR 10
COLOR 11
COLOR 12
1
CABLE
(16V426)
12 34 5
MANIFOLD
COLOR 13
COLOR 14
COLOR 15
COLOR 16
COLOR 17
COLOR 18
COLOR 19
COLOR 20
COLOR 21
+12VDC
COM
+12VDC
COM
+12VDC
COM
1
2
3
4
5
6
+12VDC
COM
+12VDC
COM
+12VDC
COM
1
2
3
4
5
6
+12VDC
COM
+12VDC
COM
+12VDC
COM
1
2
3
4
5
6
12 34 5
COLOR
CHANG
E
MODULE 8
(COLORS
41 THRU 48)
J8
MANIFOLD
J9
6
5
4
3
2
1
COM
+12VDC
COM
+12VDC
COM
+12VDC
J16
6
5
4
3
2
1
COM
+12VDC
COM
+12VDC
COM
+12VDC
6
5
4
3
2
1
COM
+12VDC
COM
+12VDC
COM
+12VDC
7
J15
J14
J10
COLOR 22
COLOR 23
COLOR 24
COLOR 25
COLOR 26
COLOR 27
COLOR 28
COLOR 29
COLOR 30
1
CABLE
(16V426)
54 3 2 1
5 4 3 2 1
BOOTH CONTROL
(24M731)
Figure 29 Electrical Schematic, Sheet 3, Hazardous
Location
332457K
47
Electrical Schematics
Dual Panel Models (MC1002, MC2002, MC3002, MC4002)
NOTE:The electrical schematic illustrates all possible
NOTE:
wiring expansions in a ProMix PD2K system; models
MC1002, MC2002, and MC4002. Some components
shown are not included with all systems.
NOTE: See Optional Cables and Modules, page 54 for
a list of cable options.
CABLE
16H078
16W159
CABLE 126232
OR 17N315
SOLVENT
METER 1
(258718)
MAC SERIES 46
SOLENOID
(16P812)
PUMPV/PFOR
FLUID REG.
UP
DOWN
FLOW SENSOR
(120278)
OR G3000 ME
TER
(239716, 258718
16M510, 16M519)
ENCODERAND MOT
OR
(16P036, 16P037)
WIRE HARNESS
(24P684, 24P685)
PUMP INLET
TRANSDUCER
(16P289, 16P290)
PUMP OUTLET
TRANSDUCER
(16P289, 16P290)
PUMPV/PFOR
FLUID REG.
MAC SERIES 46
SOLENOID
(16P812)
PUMP OUTLET
TRANSDUCER
(16P289, 16P290)
BREAKOUT MODULE PUMP 3
(24N527)
PUMP INLET
TRANSDUCER
(16P289, 16P290)
CABLE
(16T280)
SPLITTER
(16P243)
GCA
MODUL
E
EFCM
(24N913)
17L058
BARRIER
BOARD
(248192)
UP
DOWN
FLOW SENSOR
(120278)
OR G3000 ME
TER
(239716, 258718
16M510, 16M519)
CATALYST CHANGE
MODULE 6
6
(24N935)
CATALYST CHANGE
MODULE 5
6
(24N935)
COLOR CHANGE
MODULE 4
6
(24N935)
GFBPRESS. SW. 1 (121323)
GFBPRESS. SW. 2 (121323)
AIR
CONTROL
MODULE
(26A231)
SOLVENT CUTOFF VALVE (121324)
SOLVENT CUTOFF VALVE (121324)
SWITCH (120278)
SOLVENT
FLOW
INPUTS
SWITCH (120278)
SWITCH (120278)
SWITCH (120278)
SAFETY INTERLOCK SWITCH
CABLE
(121003) 3
ADV
ANCED DISPLA
Y MODULE
(24E451)
COLOR CHANGE
MODULE 7
(24R219)
7
COLOR CHANGE
MODULE 8
(24R219)
7
4 CABLE (16T659)
FAN
(24P658)
CABLE
(15V206)
GFBVALVE 1 (121324)
GFBVALVE 2 (121324)
SOLVENT
METER 2
(258718)
FAN
(24P658)
ENCODERAND MOT
OR
(16P036, 16P037)
WIRE HARNESS
(24P684, 24P685)
UP
DOWN
2
AIR FLOW SW. 2 (119159)
PLC DISCRETE 1 (4-20mA)
UP
DOWN
PUMP OUTLET
TRANSDUCER
(16P289, 16P290)
BREAKOUT MODULE PUMP 2
(24N527)
MAC SERIES 46
SOLENOID
(16P812)
CABLE 126232
OR 17N315
PUMP INLET
TRANSDUCER
(16P289, 16P290)
BREAKOUT MODULE PUMP 4
(24N527)
PUMP OUTLET
TRANSDUCER
(16P289, 16P290)
ENCODERAND MOT
OR
(16P036, 16P037)
WIRE HARNESS
(24P684, 24P685)
MAC SERIES 46
SOLENOID
(16P812)
PUMP INLET
TRANSDUCER
(16P289, 16P290)
FAN
(24P658)
BREAKOUT MODULE PUMP 1
(24N527)
ENCODERAND MOT
OR
(16P036, 16P037)
WIRE HARNESS
(24P684, 24P685)
CABLE
(15V206)
CABLE
15V819
16T072
CAN
IS BOARD
(24M485)
FAN
(24P658)
2
AIR FLOW SW. 1 (119159)
PLC DISCRETE 2 (4-20mA)
16W159
16W159
16W159
TERMINAL BLOCK WITH FUSES
POWER IN
CABLE
(15V206)
3 CABLE
(121227)
TERMINAL
BLOCK
(114095)
2
5
RELAY 2
2
RELAY 1
AWI
GATEWAY
(24R910)
COLOR CHANGE
MODULE 3
6
(24N935)
LINE FIL
TER
(16V446)
3 CABLE
(121001)
CABLE (15V206)
48V-10APOWER SUPPLY
(16U820)
3
CABLE
(121227)
5
24V
POWER
SUPPLY
(16T660)
COLOR CHANGE
MODULE 2
6
(24N935)
COLOR CHANGE
MODULE 1
6
(24N935)
INTEGRA
TION
GATEWAY
2 POSITION
SWITCH
(16U725)
CABLE
16T658
2 CABLE
(15V206)
2 CABLE
(15V206)
POWERMODULE
(26A189)
1
CABLE (16V429)
LIGHT
TOWER
(15X472)
1
BOOTHCONTROL
(24M731)
CABLE
(16V426) WITH SHUNT
(17M540)
1
CABLE
(16V426)
BOOTH
CONTROL
(24M731)
HAZARDOUS LOCA
TION
NON-HAZARDOUS LOCA
TION
Figure 30 Electrical Schematic, Sheet 1
48
332457K
Electrical Schematics
UNUSED
UNUSED
2
UNUSED
CABLE
(15V206)
3
CABLE (121227)
1
2
3
4
5
CANIS BOARD
2
(NON IS)
(IS)
4
SPLITTER
(17L058)
SPLITTER
(16P243)
UNUSED
1
2
3
(121227)
3
P3
CABLE
1
2
3
4
5
P4
(121001)
INTEGRA
TION
GATEWAY
5
1
2
3
4
5
8
3
+24VDC
COM
+24VDC
SOLVENTCUTOFF VALVE 2 (121324)
COM
GREEN/BLACK +24VDC
ORANGE/BLACK COM
GFBOUTPUT VALVE 1
BLUE/BLACK +24VDC
RED/WHITE COM
GFBOUTPUT VALVE 2
UNUSED
SIG
SAFETYINTERLOCK SWITCH
COM
UNUSED
1
2
3
4
5
6
7
8
9
10
11
12
J5
6
1
2
3
4
5
6
7
8
9
10
11
12
7
1
2
3
4
5
6
7
8
9
10
11
12
9
1
2
3
4
5
GCAMODULE
EFCM
(24N913)
5
SOLVENTCUTOFF VALVE 1 (121324)
123
J4
5
1
4
3
2
BARRI
ER
BOARD
(248192)
UNUSED
54 3 2 1
UNUSED
UNUSED
1
2
3
4
5
12345
CABLE
(16T280)
1
1
2
3
4
5
CABLE
10
3
(24M485)
12345
1
2
3
4
5
AWI
GATEWAY
(24R910)
1
UNUSED
UNUSED
2X CABLE (16V429)
16T072
12345
12345
1
2
3
4
5
P4
P3
5
4
3
2
1
25 PIN D-SUB
CABLE(16T659)
4
GROUND
BAR
24V
POWER
SUPPLY
(16T660)
1
BREAKOUT
MODULEUMP
P 1 (24N527)
3
2
12345
1234
4
7
6
5
1 2 3 45
12345
1234
1
BREAKOUT
MODULE PUMP 2 (24N527)
12 34
8
12 34
5678
3
2
12345
1234
4
12345
7
6
5
12345
1234
12 34
8
12 34
5678
BLACK
RED
RED
+48V
COM
+48V
COM
RED
BLACK
RED
BLACK
SOLVENT
METER2
(258718)
GND
SCREW
TWISTED PAIR CABLE (16W159)
TWISTEDPAIR CABLE (16W159)
MOTOR
MOUNTING
SCREW
123456789
12
10
PUMP ENCODER AND MOTOR
(16P037)
1 2 3 4 5 67 8 9
MOTOR
MOUNTING
SCREW
1011 12
UNUSED
UNUSED
UNUSED
DRAIN/FOIL
UNUSED
UNUSED
DRAIN/FOIL
1011 12
UNUSED
UNUSED
1 2 34 5 6 7 8 9
DRAIN/FOIL
UNUSED
UNUSED
UNUSED
UNUSED
DRAIN/FOIL
DRAIN/FOIL
MOTOR
GROUND
SCREW
3
1234
WIRE HARNESS
(24P685)
123456789
UNUSED
UNUSED
12345
1234
WIRE HARNESS
(24P684)
L N GND
UNUSED
UNUSED
1 2 34 5
BREAKOUT
MODULE
(24N527)
2
3
UNUSED
UNUSED
UNUSED
2
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
BREAKOUT
MODULE
(24N527)
TERMI
NAL
BLOCK
(114095)
UNUSED
L N GND
POWER IN
DETAIL B, HIGH PRESSURE PUMPS
(24M707, 24M715, 24T800)
DETAILA, LOW PRESSURE PUMPS
(24M706, 24M714, 24T799)
UNUSED
UNUSED
UNUSED
UNUSED
CABLE
(16H078)
WHITE
GRN
BLACK
L GND N
10
PUMP ENCODER AND MOTOR
(16P036)
Figure 31 Electrical Schematic, Sheet 2, Part 1
CONTINUED ON THE NEXT PAGE
332457K
49
FAN PUMP 2
(24P658)
RED
PWR
WHITE
SIG
BLACK
COM
GRN SHIELD
PUMP2
MANIFOLD
SOLVENT
METER1
(258718)
GND
SCREW
BLACK
RED
BLACK
N
LINE
FILTER
(16V446)
+24VDC
COM
+24VDC
COM
UP
PUMP1
MANIF
OLD
DOWN
OUTLET
TRANSDUCER
PUMP 2
(16P289 OR 16P290)
INLET
TRANSDUCER
PUMP 2
(16P289 OR 16P290)
RED
BLACK
RED
BLACK
FAN PUMP 1
(24P658)
+24VDC
COM
+24VDC
COM
SEE DET
AILAOR B
CABLE (126232 OR 17N315)
RED
L
CABLE (126232 OR 17N315)
+ - + - +- + 4 3 2 1
BLACK
CABLE
(16T658)
WHITE
BLACK
N04 N04
BROWN (UNUSED)
DRAIN (UNUSED)
BLUE
BLACK
ENCODER/MOT
OR
AND
WIRE HARNESS
PUMP2
MAC SERIES 46
(16P812 QTY 2)
2 POSITION
SWITCH
(16U725)
15 RELA
Y
A1
1
18
A2
RED
PWR
WHITE
SIG
BLACK
COM
GRN SHIELD
POWER MODULE
(26A189)
N (BLUE)
L (BROWN)
N03 N03
15 RELA
Y
A1
2
18
A2
BROWN (UNUSED)
DRAIN (UNUSED)
BLUE
BLACK
UP
SEE DET
AILAOR B
--++
DOWN
ENCODER/MOT
OR
AND
WIRE HARNESS
PUMP1
MAC SERIES 46
(16P812 QTY 2)
GRND
48V-10A
POWER SUPPLY
(16U280)
OUTLET
TRANSDUCER
PUMP 1
(16P289 OR 16P290)
N L
INLET
TRANSDUCER
PUMP 1
(16P289 OR 16P290)
+48V
COM
+48V
COM
GRND (GRN/YEL)
Electrical Schematics
6
8
GCAMODULE
EFCM
(24N913)
7
SIG
COM
SIG
COM
SIG
COM
SIG
COM
SIG
COM
SIG
COM
1
2
3
4
5
6
7
8
9
10
11
12
PLC DISCRETE 4-20mAINPUT 1
PLC DISCRETE 4-20mACOMMON 1
PLC DISCRETE 4-20mAINPUT 2
PLC DISCRETE 4-20mACOMMON 2
UNUSED
UNUSED
UNUSED
UNUSED
SIG
ORANGE
COM BLUE
SIG
WHITE/BLACK
COM RED/BLACK
5
9
1
2
3
4
AIR FLOW SWITCH 1
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
BLACK
WHITE
RED
GREEN
AIR FLOW SWITCH 2
SOLVENT FLOW SW. 1 (120278) LEFT BRKT
SOLVENT FLOW SW. 2 (120278) LEFT BRKT
SOLVENT FLOW SW. 3 (120278) RIGHT BRKT
TERMINAL
BLOCKS
GFB INPUT PRESSURE SWITCH 1
1
2
3
4
5
1
2
3
4
5
ADVANCED
DISPLAY MODULE
(24E451)
1
2
3
4
5
6
7
8
9
10
11
12
BLAC
K
WHITE
RED
GREEN
ORANGE
BLUE
WHITE/BLACK
RED/BLACK
GREEN/BLACK
ORANGE/BLACK
BLUE/BLACK
RED/WHITE
CABLE
15V819
GFB INPUT PRESSURE SWITCH 2
CABLE
(121003)
AIR CONTROL MODULE (26A231)
SOLVENT FLOW SW. 4 (120278) RIGHT BRKT
LIGHT
TOWER
(15X472)
+ SIG
- COM
+ SIG
- COM
+ SIG
- COM
+ SIG
- COM
+ 24VDC
- COM
+ 24VDC
- COM
AIR FLOW SWITCH 1
119159
AIR FLOW SWITCH 2
119159
GFB INPUT PRESSURE SWITCH 1
121323
GFB INPUT PRESSURE SWITCH 2
121323
RED
BLAC
K
RED
BLAC
K
GFB OUTPUT VALVE 1
121324
GFB OUTPUT VALVE 2
121324
3
25 PIN D-SUB
CABLE (16T659)
1
2
1234
1
BREAKOUT MODULE PUMP 3 (24N527)
4
12345
12345
7
6
5
1234
12 34
8
12 34
5678
2
3
12345
1234
BREAKOUT MODULE PUMP 4 (24N527)
4
12345
5
12345
7
6
1234
12 34
8
12 34
5678
RED
PWR
WHITE
SIG
BLACK
COM
GRN SHIELD
+24VDC
COM
+24VDC
COM
UP
PUMP 4
MANIFOLD
PUMP 3
MANIFOLD
G3000
METER
PUMP 3
MAC SERIES 46
(16P812 QTY 2)
MAC SERIES 46
(16P812 QTY 2)
DOWN
V/P FOR FLUID REG.
PUMP 4
OUTLET
TRANSDUCER
PUMP 4
(16P289 OR 16P290)
SEE DET
AILAOR B
INLET
TRANSDUCER
PUMP 4
(16P289 OR 16P290)
RED
BLACK
RED
BLACK
RED
PWR
WHITE
SIG
BLACK
COM
GRN SHIELD
ENCODER/M
OTOR
AND
WIRE HARNESS
PUMP 4
FAN PUMP 3
(24P658)
UP
DOWN
V/P FOR FLUID REG.
PUMP 3
+24VDC
COM
+24VDC
COM
SEE DET
AILAOR B
OUTLET
TRANSDUCER
PUMP 3
(16P289 OR 16P290)
ENCODER/M
OTOR
AND
WIRE HARNESS
PUMP 3
INLET
TRANSDUCER
PUMP 3
(16P289 OR 16P290)
+48V
COM
+48V
COM
12345
3
4
+48V
COM
+48V
COM
1
2
3
4
5
6
7
8
9
10
11
12
10
RED
BLACK
RED
BLACK
1
2
3
4
5
FAN PUMP 4
(24P658)
5
4
3
2
1
(EITHER, 239716,
258718,16M510,
OR 16M519)
GND
SCREW
G3000
METER
PUMP 4
(EITHER, 239716,
258718,16M510,
OR 16M519)
GND
SCREW
TWISTED PAIR CABLE (16W159)
TWISTED PAIR CABLE (16W159)
Figure 32 Electrical Schematic, Sheet 2, Part 2
CONTINUED ON THE NEXT PAGE
50
332457K
Electrical Schematics
FROMCAN IS BOARD (24M485)
2 CABLE(15V206)
12 34 5
COLOR
CHANGE
MODULE 1
(COLORS
1 THRU 8)
MAN
IFOLD
FLUSH
COLOR 1
COLOR 2
COLOR 3
COLOR 4
COLOR 5
COLOR 6
COLOR 7
COLOR 8
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
J8
MAN
IFOLD
J9
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
J16
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
J10
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
6
J15
J14
DUMP
COLOR 1
COLOR 2
COLOR 3
COLOR 4
COLOR 5
COLOR 6
COLOR 7
COLOR 8
MAN
IFOLD
*FLUSH
COLOR 9
COLOR 10
COLOR 11
COLOR 12
COLOR 13
COLOR 14
COLOR 15
COLOR 16
12 34 5
COLOR
CHANGE
MODULE 2
(COLORS
9 THRU 16)
1
2
3
4
5
6
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3 J15
4
5
6
J16
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
J10
J9
J8
6
J14
MAN
IFOLD
MAN
IFOLD
+24VDC
COM
+24VDC
COM
+24VDC
COM
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
DUMP*
FLUSH
COLOR 9
CATALYST 1
COLOR 10
CATALYST 2
COLOR 11
CATALYST 3
COLOR 12
CATALYST 4
COLOR 13
COLOR 14
COLOR 15
COLOR 16
CATALYST
CHANGE
MODULE 5
(CATALYST
1 THRU 4)
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
J8
+24VDC
COM
+24VDC
COM
UNUSED
UNUSED
1
2
3
4
5
6
J15
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
1
2
3
4
5
6
J14
COLOR 17
COLOR 18
COLOR 19
COLOR 20
COLOR 21
COLOR 22
COLOR 23
COLOR 24
12 34 5
COLOR
CHANGE
MODULE 3
(COLORS
17 THRU 24)
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
J8
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
J15
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
J9
6
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
UNUSED
UNUSED
J10
6
5
4
3
2
1
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
CABLE
2
COM
+24VDC
COM
+24VDC
COM
+24VDC
6
5
COM
+24VDC
COM
+24VDC
COM
+24VDC
J16 43
J10
MAN
IFOLD
MAN
IFOLD
6
5
4
3
2
1
2
1
J14
J16
J9
DUMP
CATALYST 1
CATALYST 2
CATALYST 3
CATALYST 4
12 34 5
(15V206)
2
CABLE
MAN
IFOLD
COM
+24VDC
COM
+24VDC
COM
+12VDC
6
12 34 5
*FLUSH
MAN
IFOLD
6
5
4
3
2
1
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
*FLUSH
DUMP*
COLOR 17
COLOR 25
COLOR 18
COLOR 26
COLOR 19
COLOR 27
COLOR 20
COLOR 28
COLOR 21
COLOR 29
COLOR 22
COLOR 30
COLOR 23
COLOR 24
54 3 2 1
(15V206)
2
CABLE
(15V206)
12 34 5
12 34 5
COLOR
CHANGE
MODULE 4
(COLORS
25 THRU 32)
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
J8
+24VDC
COM
+24VDC
COM
+24VDC
COM
1
2
3
4
5
6
J15
+24VDC
COM
UNUSED
UNUSED
UNUSED
UNUSED
1
2
3
4
5
6
COM
+24VDC
COM
+24VDC
COM
+24VDC
J16
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
J10
6
5
4
3
2
1
COM
+24VDC
UNUSED
UNUSED
UNUSED
UNUSED
J9
6
J14
MAN
IFOLD
6
5
4
3
2
1
DUMP*
COLOR 25
COLOR 26
COLOR 27
COLOR 28
COLOR 29
COLOR 30
12 34 5
2
CABLE(15V206)
Figure 33 Electrical Schematic, Sheet 3, Part 1
* May be unused in some configurations.
CONTINUED ON THE NEXT PAGE
332457K
51
Electrical Schematics
FROMCAN IS BOARD (24M485)
1
CABLE (16V429)
NON-HAZARDOUS LOCATION
HAZARDOUS LOCATION
MANIFOLD
COLOR FLUSH
COLOR 1
COLOR 2
COLOR 3
COLOR 4
COLOR 5
COLOR 6
COLOR 7
COLOR 8
RED
+12VDC
BLACK COM
RED
+12VDC
BLACK COM
RED
+12VDC
BLACK COM
1
2
3
4
5
6
RED
+12VDC
BLACK COM
RED
+12VDC
BLACK COM
RED
+12VDC
BLACK COM
1
2
3
4
5
6
RED
+12VDC
BLACK COM
RED
+12VDC
BLACK COM
RED
+12VDC
BLACK COM
1
2
3
4
5
6
12 34 5
COLOR
CHANGE
MODULE 7
(COLORS
6
33 THRU 40) 5
4
J9 3
J8
2
1
7
J15
J16
J14
J10
MANIFOLD
COM BLACK
+12VDC
RED
COM BLACK
+12VDC
RED
COM BLACK
+12VDC
RED
CATALYST FLUSH
6
5
4
3
2
1
COM BLACK
+12VDC
RED
COM BLACK
+12VDC
RED
COM BLACK
+12VDC
RED
CATALYST 3
6
5
4
3
2
1
COM BLACK
+12VDC
RED
COM BLACK
+12VDC
RED
COM BLACK
+12VDC
RED
CATALYST 1
CATALYST 2
CATALYST 4
COLOR 9
COLOR 10
COLOR 11
COLOR 12
1
CABLE
(16V426)
54 32 1
54 32 1
BOOTH CONTROL
(24M731)
WITH SHUNT
(17M540)
MANIFOLD
COLOR 13
COLOR 14
17M540
COLOR 15
COLOR 16
COLOR 17
12 34 5
J1
COLOR 18
COLOR 19
COLOR 20
COLOR 21
RED
+12VDC
BLACK
COM
RED
+12VDC
BLACK
COM
RED
+12VDC
BLACK
COM
1
2
3
4
5
6
RED
+12VDC
BLACK
COM
RED
+12VDC
BLACK
COM
RED
+12VDC
BLACK
COM
1
2
3
4
5
6
RED
+12VDC
BLACK
COM
RED
+12VDC
BLACK
COM
RED
+12VDC
BLACK
COM
1
2
3
4
5
6
12 34 5
COLOR
CHANGE
MODULE 8
(COLORS
41 THRU 48)
J8
MANIFOLD
COM BLACK
+12VDC
RED
COM BLACK
+12VDC
RED
COM BLACK
+12VDC
RED
COLOR 22
J9
6
5
4
3
2
1
COM BLACK
+12VDC
RED
COM BLACK
+12VDC
RED
COM BLACK
+12VDC
RED
COLOR 25
J16
6
5
4
3
2
1
J10
6
5
4
3
2
1
COM BLACK
+12VDC
RED
COM BLACK
+12VDC
RED
COM BLACK
+12VDC
RED
7
J15
J14
COLOR 23
COLOR 24
COLOR 26
COLOR 27
COLOR 28
COLOR 29
COLOR 30
1
CABLE
(16V426)
54 3 2 1
5 4 3 2 1
BOOTH CONTROL
(24M731)
Figure 34 Electrical Schematic, Sheet 3, Part 2
CONTINUED ON THE NEXT PAGE
52
332457K
Electrical Schematics
+24VDC
COM
+24VDC
COM
+24VDC
COM
CATALYST
CHANGE
MODUL
E6
(CA
TALYST
1
2 3 THRU 4)
3
J9
4 J8
5
6
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
1
2
3
4
5
6
J16
6
5
4
3
2
1
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
1
2
3
4
5
6
J10
6
5
4
3
2
1
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
6
5
4
3
2
1
COM
+24VDC
COM
+24VDC
COM
+24VDC
J16
6
5
4
3
2
1
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
J10
6
5
4
3
2
1
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
MANIFOLD
FLUSH
CATALYST 3
CATALYST 4
MANIFOLD
6
J15
J14
DUMP
CATALYST 3
CATALYST 4
2
CABLE
(15V206)
12 34 5
MANIFOLD
FLUSH
CATALYST 1
CATALYST 2
+24VDC
COM
+24VDC
COM
+24VDC
COM
54 3 2 1
CATALYST
CHANGE
MODUL
E5
(CA
TALYST
1
2 1 THRU 2)
3
J9
4 J8
5
6
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
1
2
3
4
5
6
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
UNUSED
1
2
3
4
5
6
6
J15
J14
MANIFOLD
DUMP
CATALYST 1
CATALYST 2
(15V206)
2
CABLE
12 34 5
12 34 5
COLOR
CHANGE
MODUL
E4
(COLORS
25 THRU 32)
ALTERNATE CONFIGURATION
FOR CATALYST CHANGE CONTROL
INNON-HA
ZARDOUS LOCATION
Figure 35 Electrical Schematic, Sheet 4, Alternate
Configuration for Catalyst Change Control
332457K
53
Electrical Schematics
Optional Cables and Modules
NOTE: The total length of all cable used in the system must not exceed 150 ft (45 m). See the
Electrical Schematics, page 42.
M12 CAN Cables, for Hazardous Locations
NOTE: The total length of cable used in the
hazardous location must not exceed 120 ft (36 m).
Cable Part No.
Length ft (m)
16V423
2.0 (0.6)
16V424
3.0 (1.0)
16V425
6.0 (2.0)
16V426
10.0 (3.0)
16V427
15.0 (5.0)
16V428
25.0 (8.0)
16V429
50.0 (16.0)
16V430
100.0 (32.0)
15U531
15U532
15V205
15V206
15V207
15V208
15U533
15V213
Non--Hazardous
M12 CAN Cables, for Non
Locations Only
2.0 (0.6)
3.0 (1.0)
6.0 (2.0)
10.0 (3.0)
15.0 (5.0)
25.0 (8.0)
50.0 (16.0)
100.0 (32.0)
Non--Hazardous
CAN Cables, for Non
Locations Only
Cable Part No.
Length ft (m)
125306
1.0 (0.3)
123422
1.3 (0.4)
121000
1.6 (0.5)
121227
2.0 (0.6)
121001
3.0 (1.0)
121002
5.0 (1.5)
121003
10.0 (3.0)
120952
13.0 (4.0)
54
121201
121004
121228
20.0 (6.0)
25.0 (8.0)
50.0 (15.0)
25 Pin D-SUB Cables, for Non
Non--Hazardous
Locations Only
16T659
2.5 (0.8)
16V659
6.0 (1.8)
See 8. Select Communication
Options, page 25.
Alternates for Color Change Modules
by Part Number (Factory Configuration), for
Non--Hazardous Locations Only
Non
Module Part No.
Description
24T557
2 color/2 catalyst
24T558
4 color/4 catalyst
24T559
6 color/6 catalyst
24T560
8 color/8 catalyst
Alternates for Color Change Modules
by Part Number (Factory Configuration), for
Hazardous Locations Only
24T571
2 color/2 catalyst
24T572
4 color/2 catalyst
24T573
6 color/2 catalyst
24T574
8 color/2 catalyst, 13–24
color
24T774
12 color/2 catalyst
24T775
4 color/4 catalyst
24T776
6 color/4 catalyst
24T777
8 color/4 catalyst
24T778
12 color/4 catalyst, 13–30
color
24T779
13–18 color
332457K
Dimensions
Dimensions
Figure 36
Figure 37
Figure 38
A
65.3 in.
(1659
mm)
332457K
B
with ADM
without
ADM
14.5 in.
(368 mm)
11.12 in.
(282 mm)
C
D
E
F
G
H
22.5 in.
(572 mm)
19.26 in.
(489 mm)
2.25 in.
(57 mm)
18.0 in.
(457 mm)
17.26 in.
(438 mm)
0.52 in.
(13 mm)
55
Technical Data
Technical Data
Positive Displacement
Proportioner
U.S.
Metric
MC1000, MC1002, and
MC3000 Air Spray
Systems
300 psi
2.1 MPa, 21 bar
MC2000, MC2002,
MC4000, and MC4002
Air-Assisted Spray
Systems
1500 psi
10.5 MPa, 105 bar
100 psi
0.7 MPa, 7.0 bar
85–100 psi
0.6–0.7 MPa, 6.0–7.0 bar)
Maximum fluid working
pressure:
Maximum working air
pressure:
Air supply:
Air filter inlet size for air
logic:
1/4 npt(f)
Air filter inlet size for
atomizing air:
3/8 npt(f)
Air filtration for air logic:
5 micron (minimum) filtration required; clean and dry air
Air filtration for atomizing
air (user-supplied):
30 micron (minimum) filtration required; clean and dry air
Mixing ratio range:
Fluids handled:
0.1:1 – 50:1, ±1%
one or two component:
• solvent and waterborne paints
• polyurethanes
• epoxies
• acid catalyzed varnishes
• moisture sensitive isocyanates
Viscosity range of fluid:
20–5000 centipoise
Fluid filtration
(user-supplied):
100 mesh minimum
Maximum fluid flow:
800 cc/minute (depending on material viscosity)
Fluid outlet size:
External power supply
requirements:
1/4 npt(m)
90 - 250 Vac, 50/60 Hz, 7 amps maximum draw
15 amp maximum circuit breaker required
8 to 14 AWG power supply wire gauge
Operating temperature
range:
36 to 122°F
2 to 50°C
Storage temperature
range:
–4 to 158°F
–20 to 70°C
Weight (approximate):
195 lb
88 kg
Sound data:
56
Less than 75 dB(A)
332457K
Technical Data
Positive Displacement
Proportioner
Metric
U.S.
Wetted parts:
MC0500 and MC0502
Pumps sold separately; see selected pump manual for wetted parts information.
MC1000, MC1002,
MC2000, and MC2002
17–4PH, 303, 304 SST, Tungsten carbide (with nickel binder),
MC3000, MC3002,
MC4000, and MC4002
316 SST, 17–4PH SST, PEEK,
332457K
perfluoroelastomer; PTFE, PPS, UHMWPE
perfluoroelastomer; PTFE, PPS, UHMWPE
57
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its
name to be free from defects in material and workmanship on the date of sale to the original purchaser for use.
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of
twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance
with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction,
damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper
maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco
be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures,
accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation,
operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized
Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace
free of charge any defective parts. The equipment will be returned to the original purchaser transportation
prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be
made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS
FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The
buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost
profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available.
Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT,
MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not
manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of
their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of
these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco
supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold
hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices
and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be
drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en
Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou
en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
For the latest information about Graco products, visit www.graco.com.
To place an order, contact your Graco Distributor or call to identify the nearest distributor.
Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents.
Original Instructions. This manual contains English. MM 332457
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
2013,, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
Copyright 2013
www.graco.com
Revision K, March 2018

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement