Graco 3A1937A - Heated Platen Kits Instructions


Add to my manuals
30 Pages

advertisement

Graco 3A1937A - Heated Platen Kits Instructions | Manualzz

Instructions

Heated Platen Kits

3A1937A

EN

For heating bulk supply of medium to high viscosity sealant and adhesive materials for

VPM systems. Not for use in hazardous locations. Intended for indoor use only.

24E267

Heated platen kit, high volume

24E268

Heated platen kit, low volume

Important Safety Instructions

Read all warnings and instructions in VPM,

Instructions manuals.

Save all instructions.

2

Contents

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

System Description . . . . . . . . . . . . . . . . . . . . . . . 3

Power Requirements . . . . . . . . . . . . . . . . . . . . . . 3

Component Identification . . . . . . . . . . . . . . . . . . . . 4

Kit Components . . . . . . . . . . . . . . . . . . . . . . . . . 4

Temperature Control Module . . . . . . . . . . . . . . . . 5

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Power Requirements . . . . . . . . . . . . . . . . . . . . . . 6

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Temperature Control Module . . . . . . . . . . . . . . . 16

Platen Maintenance . . . . . . . . . . . . . . . . . . . . . 17

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Common Problems . . . . . . . . . . . . . . . . . . . . . . 18

Temperature Control Module . . . . . . . . . . . . . . . 21

Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Replace Platen Heaters and Sensor . . . . . . . . . 22

Replace High Power Temperature Control Module

23

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Platen Heater Kits, 24E267 and 24E268 . . . . . 24

Heat Panel Module, 24K203 and 24K204 . . . . . 26

Heater Platen Assembly, 24C493 . . . . . . . . . . . 28

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 30

Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . 30

3A1937A

Overview

System Description

The heated platen kit is a field installed kit to add heat to the platen. The additional heat may change the viscosity properties of the material and allow the material to flow easier through the system.

The heat is controlled by Graco Control Architecture components: High Power Temperature Control Modules

(HPTCM) and the display module. The display module provides the user interface for the entire VPM system.

Power Requirements

A 20A (minimum) - 30A (maximum) circuit breaker must be installed on the incoming power supply.

Voltage

230 V

400V

Wattage

3,500 per Platen

1 Heated Platen

* Add to power requirements of VPM system. Amps maximum per leg shown.

17

17

Amps*

2 Heated Platens

27

34

Overview

3A1937A 3

Component Identification

Component Identification

Kit Components

1

2

3

4

Key:

1 RTD Temperature Sensor

2 Heater Coil

3 Temperature Limit Switch

4 Junction Box

5 High Power Temperature Control Module (HPTCM)

6 Relay

4

5

6

3A1937A

Component Identification

Temperature Control Module

2

LED

Signals

5

1

7

3 ti12352a1

F IG . 1: High Power Temperature Control Module Sensor Connections

6

4 ti12353a1

Key:

1 N/A

2 RTD Temperature Sensor Connection

3 Output Power Connection

4 DC Output Connection

5 Input Power Connection

6 CAN Connections

7 Rotary Selector Switch, Token Access

Adjust Rotary Switch

The rotary switch setting indicates which zone the temperature control module will control in the system. The high power module uses an 8-position rotary switch.

Set the rotary switch (S) to the specific selection according to the settings listed in the following table.

Setting

0

1

2

5

6

3

4

7

Zone

Not Used

B (Blue) Primary Heat

Not Used

A (Red) Primary Heat

Not Used

Not Used

Not Used

Not Used

F IG . 2

High Power Module Rotary Switch Location

S ti12360a

3A1937A 5

Installation

Installation

To avoid serious injury or machine damage, all electrical connections need to be done by a qualified electrician familiar with local codes.

Power Requirements

Ensure that the electrical panel located within the Power Distribution Box has the correct circuit breakers for installing the kit. If the current Power Distribution Box does not have this configuration, contact your local distributor inquiring about a Power Distribution Box upgrade kit.

Grounding

Ground the system as instructed within this manual.

6

The equipment must be grounded to reduce the risk of static sparking and electric shock. Electric or static sparking can cause fumes to ignite or explode.

Improper grounding can cause electric shock.

Grounding provides an escape wire for the electric current.

Setup

1. Access the Platen

a.

Perform Remove Drum Procedure found in

VPM Instructions manuals.

b.

Perform Shutdown Procedure found in VPM

Instructions manuals.

c.

Thoroughly clean all material that may be found on the top of the platen.

d.

Turn off all sources of power to the machine.

3A1937A

Installation

2. Install Heat Coils and Thermostat Switch

Install both heat coils onto the platen as shown below.

- (6) 1/4-20 Stud

- (6) Flat Washer

- (6) Lock Washer

- (6) Nut

- (1) Thermostat

- (2) Screws

3. Connect Ground Wires

Connect ground wires to the terminal lug and platen covers (not shown in view). Attach conduit to platen cover (not shown) and route wires through the conduit when connections are complete.

- (3) Ground Wires

- (2) Lock Wasers

- (2) Nuts

3A1937A

- (1) Ground Screw

7

Installation

4. Connect Power Leads

Connect leads as shown below. Route all wires through conduit when connections are complete.

- (2) “B” Leads

- (3) “A” Leads

5. Mount RTD

Mount RTD as shown below. Route wire through conduit when connections are complete.

8

- (1) RTD

- (1) Washer

- (1) M5 Screw

3A1937A

6. Attach Platen Covers

NOTICE

To prevent damage to wires, ensure wires are not pinched when assembling and securing platen covers.

- (1) Conduit

- (1) Knob

- (2) Covers

7. Mount Junction Box

- (2) 3/8-16 Bolts

- (4) #10-32 Screws

- (4) Lock Washers

- (1) Conduit from platen

3A1937A

Installation

- (1) Knob

- (1) Plug

9

Installation

8. Route Power Cord and Signal Cable

Route power cord and signal cable as shown below. It is recommended to start from the cube base and route to junction box.

Routing

Cord and cable to be routed under cover

9. Connect Leads in Junction Box

Connect “A” leads, “B” leads, ground, and signal cable within junction box.

10 3A1937A

Installation

10.Mount New Electrical Panel in Power Pack Base Cube

a.

Disconnect all auxiliary components (fans) from existing electrical panel.

b.

Remove existing electrical panel.

c.

Mount electrical panel that came with the kit into the base cube.

d.

Connect power cable and signal cable (routed in previous step) to High Power Temperature Control Module as shown below.

- (1) Signal Cable

- (1) Power Cable

3A1937A 11

Installation

11.Reconnect Auxiliary Components

Reconnect auxiliary components (fans) to the electrical panel shown below.

DC Power Pack

Fan Leads

Base Cube Fan

Leads

Power Leads

12 3A1937A

12.Route Power Cable from Distribution Box to Base Cube

Route power cable from distribution box to base cube as shown below.

Ground Terminal

Power Leads from either “A” or

“B” breaker as applicable

Installation

3A1937A

Ground Terminal

Power Junction

Connector

13

Installation

13.Sensor Resistance Checks 14.Heater Resistance Checks

Conduct these electrical checks with the main disconnect OFF.

Conduct these electrical checks with the main power disconnect OFF.

The heated platen system includes a heat sensor and controller for each of the two optional heated zones. To check sensor resistance:

1.

Make sure the power is off and that the disconnect switch is in the OFF position.

2.

Make electrical resistance checks for the components.

3.

Replace any parts that have resistance readings that do not comply with the ranges listed in Table 1.

NOTE: Check resistance at ambient room temperature (63°– 77°F [17°– 25°C] ).

Table 1: RTD Sensor Resistance

Zone Component Connector Pin

1,2 Platen Pin 1 to 3

Range (ohms)

1050-1100

Ω

To check heater resistance:

1.

Make sure the power is off and that the disconnect switch is in the OFF position.

2.

Make electrical resistance checks for the components. Refer to Table 2. Heater terminal pins are connected to the HPTCM.

3.

Replace any parts whose resistance readings do not comply with the ranges listed in Table 2.

NOTE: Check resistance at ambient room temperature (63°– 77°F [17°– 25°C] ).

Table 2: Resistance Chart of All Heaters

Zone Component

1,2 Platen

Between

Terminals

1 and 3

Unit

Voltage

240

Range

(ohms)

15 +5/-5

1

3

F IG . 3: RTD Connector Pins

F IG . 4: Heater Terminal Pins

14 3A1937A

Setup

Setup

For individual screen shot details, refer to VPM Instructions manual.

1.

Make sure the power is on and that the disconnect switch is in the ON position.

2.

Navigate to Conditioning Screen 1 and select the appropriate heater.

6.

Edit the setpoint and alarm values and then press the page back button to return to the previous screen.

1.

Navigate to the Status Screen, Conditioning Control Screen.

3.

Navigate to Conditioning Screen 2 to verify proper selection of heaters is correct.

2.

Press screen.

to enter the Conditioning Control

3.

Use the arrows keys to navigate to the desired zone.

4.

Press and navigate to the component you wish to edit the temperature setpoint and alarm.

5.

Press the enter key to display the setpoint and alarm values associated with that component.

4.

Press to turn the selected zone on. When a zone is on, the button will be selected. Press the button again to turn the zone off.

Zone

Setting

OFF

ON

Color

Black

Grey

Yellow

Green

Definition

Dispense Disabled

Dispense Allowed

Dispense Disabled

Dispense Allowed

3A1937A 15

Maintenance

Maintenance

Temperature Control Module Install Upgrade Token

1.

Turn off system power at main power switch (MP).

2.

Remove token access panel.

Clean

Keep heat sink fins clean at all times. Wipe the fins clean with a dry cloth or clean them using compressed air.

NOTE:

Do not use conductive cleaning solvents on the temperature control modules.

ti12354a1

F IG . 6: Remove Access Cover

3.

Insert and press token (T) firmly into slot. There is no preferred orientation of the token.

Heat Sink Fins

F IG . 5: Clean Heat Sink Fins ti12353a1

M

F IG . 7: Install Token

T ti12355a1

L

4.

Turn on system power at main power switch (MP).

The red indicator light (L) will flash until new firmware is completely loaded. Wait for red indicator light to stop flashing.

5.

Turn system power off.

6.

Remove token (T).

7.

Replace token access panel.

16 3A1937A

Maintenance

Platen Maintenance Remove and Reinstall Platen Wipers

Refer to Supply Units Repair-Parts manual for instructions.

If the platen does not come out of the pail easily when the pump is being raised, the air assist tube or check valve may be plugged. A plugged valve prevents air from reaching the underside of the plate to assist in raising it from the pail.

1.

Turn off main disconnect.

2.

Relieve pressure and disassemble air assist valve.

Refer to Supply Systems Repair-Parts manual.

3.

Clear air assist tube in platen. Clean all parts of valve and reassemble. Refer to Supply Systems

Repair-Parts manual.

4.

Remove bleed stick from platen. Push bleed stick through bleed relieve port (T) to remove material residue. See F

IG

. 8.

5.

Remove platen covers. See F

IG

. 8.

a.

Remove platen cover fasteners (70).

b.

Remove both platen covers (49) and ground wire from platen.

6.

Remove any excess fluid. Use a soft wire brush on heater coils (48). See F

IG

. 8.

7.

Inspect platen heater blocks (43) or heater (48) for burn or melt spots. Replace platen heater if necessary. See F

IG

. 8.

8.

Check for loose connections and damaged wires.

9.

Follow steps in reverse order to reassemble platen.

NOTE: Torque platen cover fasteners (70) to 60 +/-

10 in-lbs (6.8 +/- 1.1 N•m) for 55 gallon platen.

Bleed

Stick

T

70

49

43

48 r_wm2179_313296_6a

F IG . 8: Remove Platen Covers and Heaters

3A1937A 17

Troubleshooting

Troubleshooting

Before performing any troubleshooting procedure:

1.

Perform Pressure Relief Procedure found in vpm

Instructions manuals.

2.

Turn main power OFF.

3.

Allow equipment to cool.

Try the recommended solutions in the order given for each problem, to avoid unnecessary repairs. Also, determine that all circuit breakers, switches, and controls are properly set and wiring is correct before assuming there is a problem.

Common Problems

Problem

Heating is slow.

Cause

Heater defective.

Low power.

Heating over shoots.

Shorted module.

Verification Solution

Measure resistance of heater.

Measure voltage across circuit breakers. Voltage should measure between

190 and 275 Vac.

Follow Heater Resistance

Checks , page 14.

1.

If voltage is lower than expected, use electrical schematic to locate faulty wiring or connection.

Verify for given zone that temperature does not increase when zone is disabled.

2.

Have a qualified electrician service electrical components.

Verify RTD wire or heater power cord is attached to correct heat module.

Replace module.

18 3A1937A

Problem

Missing module.

Troubleshooting

Cause

Modules not on network.

Verification

Verify attached modules through Advanced Setup screens 4 and 5.

Cable disconnected.

Module with wrong rotary switch setting.

Verify all green LEDs are illuminated and yellow

LEDs are flashing.

Verify rotary switch is set correctly.

Solution

Enter Setup screen and scroll to Advanced Setup screens 4 and 5. These screens lists all components corresponding software revision number on network.

Reconnect/replace faulty cable.

1.

Remove power from unit.

2.

Remove access cover and visually check rotary switch setting.

3.

If incorrect, set to correct setting. See

Adjust Rotary Switch

,

page 5, for selector

switch locations.

4.

Replace access cover.

3A1937A 19

Troubleshooting

No heat.

Problem Cause

Tripped circuit breaker.

Low power.

Cable unplugged/loose wire.

Circuit breaker tripped.

Zone not enabled.

Incorrect temperature set point.

Bad heater.

Contactor not closing.

Verification Solution

Visually check circuit breaker for a tripped condition.

Measure voltage across circuit breakers. Voltage should measure between

190 and 275 Vac.

Determine cause of tripped circuit breaker. Then repair fault and reset main circuit breaker.

1.

If voltage is lower than expected, use electrical schematic to locate faulty wiring or connection.

Check for loose or disconnected wires and plugs.

Visually check circuit breaker for a tripped condition.

Verify zone is enabled on

Heat Run screen.

Verify zone has a correct temperature setting on

Heat Run screen.

Measure resistance of heater.

2.

Have a qualified electrician service electrical components.

Attach plug/wire.

Determine fault that caused circuit breaker to trip.

Repair fault, and reset circuit breaker.

Enter Setup screen and enable correct zone.

Enter Setup and enter correct temperature.

1.

Unplug suspected heater zone from heater module.

2.

Follow Heater Resistance Checks , page

14.

3.

If resistance is outside allowable value, replace heater(s).

Turn on heat for zone A1 or

B1and ensure contactor closes.

1.

Verify that there are no other error conditions that would prevent heater from starting.

2.

Replace contactor.

20 3A1937A

Temperature Control Module

Diagnostic Information

Module Status LEDs

Signal

Green on

Yellow on

Red solid

Red flashing

Blue light off

(High Power

Module only)

Blue flashing

(High Power

Module only)

Description

Temperature control module is powered up.

Internal communication in progress.

Temperature control module failure.

See Troubleshooting table.

Software is updating.

Temperature control module is off.

See Troubleshooting table.

Length of flashes indicates amount of power running through temperature control module.

LED

Signals ti12353a1

F IG . 9: LED Signals

Troubleshooting

3A1937A 21

Repair

Repair

Replace Platen Heaters and

Sensor

55 Gallon Platen Heater and Sensor

1.

Turn off main disconnect.

2.

Remove both platen cover fasteners (70).

3.

Remove both platen covers (49) and ground wire from platen.

70

49

59

11

64

43 c.

Disconnect four platen heater wires (labeled A and B) and RTD sensor connector in the terminal box.

d.

Remove screws and washers.

Remove platen heater blocks (43) and RTD sensor.

5.

Install new platen heaters and RTD sensor. Secure

RTD sensor with screw and washer. Secure platen heater blocks with nuts and washers.

6.

Label platen heater wires A and B. Reroute platen heater wires and platen RTD sensor through the conduit to the junction box. Reconnect the four wires to the appropriate terminal block A and B. Reconnect the platen RTD sensor.

7.

Reinstall junction box cover. Secure with screws and tighten strain relief nut.

8.

Reconnect ground wire, and install platen covers.

Secure platen covers with fasteners. Torque platen cover fasteners to 60 in-lbs +/- 10 in-lbs (6.8 +/- 1.1

N•m)

9.

Reconnect displacement pump using screws and clamps.

109

58

82 ti18061a

F

IG

. 10: Replace Platen Heaters and RTD Sensor

4.

Remove platen heater blocks (43).

a.

Use a hex wrench to remove three nuts (59) and washers (11, 64) from each heater block.

b.

Remove screws from junction box cover.

Loosen strain relief nut, and remove junction box cover.

22 3A1937A

Repair

Replace High Power

Temperature Control Module

1.

Open enclosure door of the base cube. Disconnect outbound power supply and RTD cables from

HPTCM.

2.

Remove electrical enclosure side panel. See Platen

Heater Kits, 24E267 and 24E268 on page 24.

3.

Disconnect all incoming cables HPTCM.

4.

Remove both screws that secure brackets of the

HPTCM to the electrical enclosure. Remove

HPTCM.

5.

Follow steps in reverse order to install new HPTCM.

NOTE: Reuse brackets to install new HPTCM.

6.

Upload the correct TCM software. See Install

Upgrade Token , page 16, for instructions.

7.

Remove cover of new HP TCM and set selector switch to “3” for Red Ram A or “1” for Blue Ram B.

Selector

Switch

TI12360a

F IG . 11: Set Selector Switch

3A1937A 23

Parts

Parts

Platen Heater Kits, 24E267 and 24E268

003

004

001

24

005

002

007

008,

009,

010,

011,

012,

013,

014,

015

006

3A1937A

Ref Part

001 24K203

24K204

002 24C493

003 24E266

004 125519

005 15W368

006 068112

007 121172

008 24K201

009 113802

010 24E265

011 100016

012 103833

013 261821

014 123411

015 123405

Description

MODULE, panel, pwr, heat, pri, vpm, hv

MODULE, panel, pwr, heat, pri, vpm, lv

KIT, platen heater, wrmmlt 200l

HARNESS, wire, 12/3, hptcm, platen, vp

CABLE, m8, 4-pin, mf, 5m, molded

COUPLER, conduit

CONDUIT, igus, id 12.9mm

GRIP, cord, .39-.56, 1/2

BRACKET, platen, heated, vpm, painted

SCREW, hex hd, flanged

ENCLOSURE, platen, heated, vpm, painted

WASHER, lock

SCREW, mach, crbh

CONNECTOR, wire, 6awg

FERRULE, wire, 14awg, twin

FERRULE, wire, 14awg

Quantity

24E267, KIT, 24E268, KIT, platen, heater, platen, heater, vpm, high volume, blue vpm, low volume, red

1

1

1

1

2

1

1

1

1

2.670

1

1

2

2

2.670

1

1

1

4

4

2

4

4

2

1

2

2

2

2

2

Parts

3A1937A 25

Parts

Heat Panel Module, 24K203 and 24K204

24K203 Shown

103,

105

103,

105

104,

105

109

103,

105

104,

105

111,

112,

113

102

114

110

26

101

3A1937A

Ref

101

102

Part Description

15Y917 PANEL, electric, heat

24C363 MODULE, assy, pwr, heat, pri, hv

24C367 MODULE, assy, pwr, heat, pri, lv

103

104

123452

116876

105 103833

106 ◆ 100021

107

100028

108

100015

109 24F073

24F074

HOLDER, anchor, wire tie, nylon

WASHER, flat

SCREW, mach, crbh

SCREW, cap hex hd

WASHER, lock

NUT, hex mscr

HARNESS, wire, ground, 8awg, hvrh, hv

HARNESS, wire, ground, 8awg, hvrh, lv

110

111

112

113

114

24F071

24F072

HARNESS, wire, male, 2pin, 16/2, hvrh

HARNESS, wire, male, 2pin, 16/2, hvrh

MODULE, gca, hptcm 255774

15R535 BRACKET, mounting, gca high power

117831 SCREW, mach., pan hd

24K213 HARNESS, wire, heat, inline, 70"l

24C304 HARNESS, wire, pdb, inline heater

Not Shown

Quantity

24K203, MODULE, panel, pwr, heat, pri, vpm, high volume

24K204, MODULE, panel, pwr, heat, pri, vpm, low volume

1

1

1

4

7

7

1

2

2

1

1

2

2

7

7

1

4

1

1

2

4

1

1

1

1

2

4

1

Parts

3A1937A 27

202

210,

211

207

203,

204,

205,

206

218

Parts

Heater Platen Assembly, 24C493

208

209

208

28

214,

215,

217

216

3A1937A

219

209

213

214,

215,

217

201

Ref

201

202

203

204

205

206

207

Part

15V429

15V427

15W859

176692

100015

100016

16D383

208

209

210

211

213

214

215

216

255733

15W792

117026

110170

123079

111640

100166

116343

217 16A574

218 16A356

219 ▲ 15J075

Description

CONDUCTOR, block, heater

HEATER, coil

STUD, 1/4-20 x 1.25

WASHER, flat

NUT, hex mscr

WASHER, lock

SENSOR, rtd, 1k ohm, shielded

COVER, platen front, assy

FASTENER, platen, cover

SCREW, shcs m5x12

WASHER

PLUG, finishing, 13/16, nickel pl

WASHER, lock, internal

NUT, full hex

SCREW, ground

WIRE, ground

WIRE, ground

LABEL, safety, hotsurf& energized

▲ Replacement Danger and Warning labels, tags, and cards are available at no cost.

2

1

2

2

1

1

2

2

Quantity

2

2

6

6

1

6

6

2

1

1

Parts

3A1937A 29

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by

Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED

TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE .

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy

(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT

MANUFACTURED BY GRACO . These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

For the latest information about Graco products, visit www.graco.com.

TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.

Phone: 612-623-6921 or Toll Free: 1-800-746-1334 Fax: 330-966-3006

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

For patent information, see www.graco.com/patents.

Original instructions.

This manual contains English. MM 3A1937.

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2012, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals