YASKAWA CIMR-G7A4055 Instruction manual
PDF
문서
광고
광고
YASKAWA Varispeed G7 INSTRUCTION MANUAL GENERAL PURPOSE INVERTER (ADVANCED VECTOR CONTROL) MODEL: CIMR-G7A 200V CLASS 0.4 to 110kW (1.2 to 160kVA) 400V CLASS 0.4 to 300kW (1.4 to 460kVA) Upon receipt of the product and prior to initial operation, read these instructions thoroughly, and retain for future reference. YASKAWA MANUAL NO. TOE-S616-60.1E Preface This manual is designed to ensure correct and suitable application of Varispeed G7-Series Inverters. Read this manual before attempting to install, operate, maintain, or inspect an Inverter and keep it in a safe, convenient location for future reference. Be sure you understand all precautions and safety information before attempting application. General Precautions • The diagrams in this manual may be indicated without covers or safety shields to show details. Be sure to restore covers or shields before operating the Units and run the Units according to the instructions described in this manual. • Any illustrations, photographs, or examples used in this manual are provided as examples only and may not apply to all products to which this manual is applicable. • The products and specifications described in this manual or the content and presentation of the manual may be changed without notice to improve the product and/or the manual. • When ordering a new copy of the manual due to damage or loss, contact your Yaskawa representatives or the nearest Yaskawa sales office and provide the manual number shown on the front cover. • If nameplates become warn or damaged, order new ones from your Yaskawa representatives or the nearest Yaskawa sales office. i Safety Information The following conventions are used to indicate precautions in this manual. Failure to heed precautions provided in this manual can result in serious or possibly even fatal injury or damage to the products or to related equipment and systems. Indicates precautions that, if not heeded, could possibly result in loss of life or serious injury. WARNING CAUTION Indicates precautions that, if not heeded, could result in relatively serious or minor injury, damage to the product, or faulty operation. Failure to heed a precaution classified as a caution can result in serious consequences depending on the situation. Indicates important information that should be memorized. IMPORTANT ii Safety Precautions Confirmations upon Delivery CAUTION • Never install an Inverter that is damaged or missing components. Doing so can result in injury. Installation CAUTION • Always hold the case when carrying the Inverter. If the Inverter is held by the front cover, the main body of the Inverter may fall, possibly resulting in injury. • Attach the Inverter to a metal or other noncombustible material. Fire can result if the Inverter is attached to a combustible material. • Install a cooling fan or other cooling device when installing more than one Inverter in the same enclosure so that the temperature of the air entering the Inverters is below 45°C. Overheating can result in fires or other accidents. Wiring WARNING • Always turn OFF the input power supply before wiring terminals. Otherwise, an electric shock or fire can occur. • Wiring must be performed by an authorized person qualified in electrical work. Otherwise, an electric shock or fire can occur. • Be sure to ground the ground terminal. (200 V Class: Ground to 100 Ω or less, 400 V Class: Ground to 10 Ω or less) Otherwise, an electric shock or fire can occur. • Always check the operation of any emergency stop circuits after they are wired. Otherwise, there is the possibility of injury. (Wiring is the responsibility of the user.) • Never touch the output terminals directly with your hands or allow the output lines to come into contact with the Inverter case. Never short the output circuits. Otherwise, an electric shock or ground short can occur. • If the power supply is turned ON during the FWD (or REV) Run Command is given, the motor will start automatically. Turn the power supply ON after verifying that the RUN signal is OFF. Failure to observe this warning may result in injury. • When the 3-wire sequence is set, do not make the wiring for the control circuit unless the multifunction input terminal constant is set. Failure to observe this warning may result in injury. CAUTION • Check to be sure that the voltage of the main AC power supply satisfies the rated voltage of the Inverter. Injury or fire can occur if the voltage is not correct. • Do not perform voltage withstand tests on the Inverter. Otherwise, semiconductor elements and other devices can be damaged. • Connect braking resistors, Braking Resistor Units, and Braking Units as shown in the I/O wiring examples. Otherwise, a fire can occur and the Inverter, braking resistors, Braking Resistor Units, and Braking Units can be damaged. iii CAUTION • Tighten all terminal screws to the specified tightening torque. Otherwise, a fire may occur. • Do not connect AC power to output terminals U, V, and W. The interior parts of the Inverter will be damaged if voltage is applied to the output terminals. • Do not connect phase-advancing capacitors or LC/RC noise filters to the output circuits. The Inverter can be damaged or interior parts burnt if these devices are connected. • Do not connect magnetic contactors to the output circuits. If a load is connected while the Inverter is operating, surge current will cause the overcurrent protection circuit inside the Inverter to operate. Setting User Constants CAUTION • Disconnect the load (machine, device) from the motor before performing rotational autotuning. The motor may turn, possibly resulting in injury or damage to equipment. Also, motor constants cannot be correctly set with the motor attached to a load. • Stay clear of the motor during rotational autotuning. The motor repeats running and stopping until autotuning has been completed, possibly resulting in injury. • In stationary autotuning 1, when the motor is first operated in the drive mode after tuning, the remaining motor constants E2-02 (Motor rated slip) and E2-03 (Motor no-load current) are set automatically. To perform an operation immediately after stationary autotuning 1, use the following procedure under the recommended conditions. (1) Check the values of E2-02 and E2-03 in verify mode or advanced programming mode. (2) Run the motor once in drive mode under the following conditions. • The Inverter and the motor are connected. • The motor shaft is not locked with a mechanical brake or other stopping mechanism (or function). • A motor-load ratio of 30% or less is maintained. • A speed of 30% or more of the base frequency set at E1-06 (default = highest frequency) is maintained at a constant speed for one second or more. (3) After stopping the motor, check the values of E2-02 and E2-03 again in verify mode or advanced programming mode. If the values of E2-02 and E2-03 differ from the ones before the first operation was carried out, the settings have been successfully completed. Next, check if the values are suitable or not. If the values of E2-02 and E2-03 differed greatly from the reference data of the motor in the test report or the instruction manual (TOE-S616-60.1), hunting, motor vibrations, insufficient motor torque, or an overcurrent may occur because the motor is operated although the aforementioned conditions have not been fulfilled after stationary autotuning 1. For elevators, failure to observe this caution may result in the cage falling or injury. If so, perform stationary autotuning 1 again and run the motor using the aforementioned procedure under the recommended conditions or perform stationary autotuning 2 or rotational autotuning. Usually the standard setting for E2-02 is 1 Hz to 3 Hz, and that for E2-03 is 30% to 65% of the rated current for a generalpurpose motor. Generally, the larger the motor capacity is, the smaller the rated slip and the ratio of the no-load current to the rated current become. Use the data given in Factory Settings that Change with the Inverter Capacity (o2-04) of Chapter 5 User Constants as a reference. Trial Operation WARNING • Check to be sure that the front cover is attached before turning ON the power supply. An electric shock may occur. • Do not come close to the machine when the fault reset function is used. If the alarmed is cleared, the machine may start moving suddenly. Also, design the machine so that human safety is ensured even when it is restarted. Injury may occur. • Provide a separate emergency stop switch; the Digital Operator STOP Key is valid only when its function is set. Injury may occur. iv WARNING • Reset alarms only after confirming that the RUN signal is OFF. Injury may occur. CAUTION • Don't touch the radiation fins (heatsink), braking resistor, or Braking Resistor Unit. These can become very hot. Otherwise, a burn injury may occur. • Be sure that the motor and machine is within the applicable ranges before starting operation. Otherwise, an injury may occur. • Provide a separate holding brake if necessary. Always construct the external sequence to confirm that the holding brake is activated in the event of an emergency, a power failure, or an abnormality in the Inverter. Failure to observe this caution can result in injury. • If using an Inverter with an elevator, take safety measures on the elevator to prevent the elevator from dropping. Failure to observe this caution can result in injury. • Don't check signals while the Inverter is running. Otherwise, the equipment may be damaged. • Be careful when changing Inverter settings. The Inverter is factory set to suitable settings. For the Inverters in the 400 V class of 55 kW or more, however, select the correct power supply voltage jumper according to the input voltage. Otherwise, the equipment may be damaged. Maintenance and Inspection WARNING • Do not touch the Inverter terminals. Some of the terminals carry high voltages and are extremely dangerous. Doing so can result in electric shock. • Always have the protective cover in place when power is being supplied to the Inverter. When attaching the cover, always turn OFF power to the Inverter through the MCCB. Doing so can result in electric shock. • After turning OFF the main circuit power supply, wait until the CHARGE indicator light goes out before performing maintenance or inspections. The capacitor will remain charged and is dangerous. • Maintenance, inspection, and replacement of parts must be performed only by authorized personnel. Remove all metal objects, such as watches and rings, before starting work. Always use grounded tools. Failure to heed these warning can result in electric shock. • For 400-V class Inverters of 55 kW to 300 kW with SPEC: E or later, take safety measures such as the installation of an emergency-stop switch before adjusting constants. Failure to do so may result in injury caused by the motor accidentally rotating during stationary autotuning performed by the Inverter when the constants are adjusted. • Provide a separate holding brake if necessary. Always make any adjustments other than those involving the operation of the Inverter with the holding brake released. Failure to observe this caution may result in injury. • If using an Inverter with an elevator, take safety measures on the elevator to prevent the elevator from dropping. Failure to observe this caution can result in injury. v CAUTION • A CMOS IC is used in the control board. Handle the control board and CMOS IC carefully. The CMOS IC can be destroyed by static electricity if touched directly. • Do not change the wiring, or remove connectors or the Digital Operator, during operation. Doing so can result in personal injury. Other WARNING • Do not attempt to modify or alter the Inverter. Doing so can result in electrical shock or injury. CAUTION • Do not subject the Inverter to halogen gases, such as fluorine, chlorine, bromine, and iodine, at any time even during transportation or installation. Otherwise, the Inverter can be damaged or interior parts burnt. vi Warning Information and Position There is warning information on the Inverter in the position shown in the following illustration. Always heed the warnings. Warning information position Warning information position Illustration shows the CIMR-G7A20P4 Illustration shows the CIMR-G7A2018 Warning Information ! WARNING Risk of electric shock. yRead manual before installing. yWait 5 minutes for capacitor discharge after disconnecting power supply. ! AVERTISSEMENT Risque de décharge électrique. yLire le manuel avant l' installation. yAttendre 5 minutes aprés la coupure de l' allmentation. Pour permettre la décharge des condensateurs. ! y y vii Warranty Information Free Warranty Period and Scope Warranty Period This product is warranted for twelve months after being delivered to Yaskawa’s customer or if applicable eighteen months from the date of shipment from Yaskawa’s factory whichever comes first. Scope of Warranty Inspections Periodic inspections must be conducted by the customer. However, upon request, Yaskawa or one of Yaskawa’s Service Centers can inspect the product for a fee. In this case, if after conferring with the customer, a Yaskawa product is found to be defective due to Yaskawa workmanship or materials and the defect occurs during the warranty period, then this fee will be waived and the problem remedied free of charge. Repairs If a Yaskawa product is found to be defective due to Yaskawa workmanship or materials and the defect occurs during the warranty period, Yaskawa will provide a replacement, repair the defective product, and provide shipping to and from the site free of charge. However, if the Yaskawa Authorized Service Center determines that the problem with a Yaskawa product is not due to defects in Yaskawa’s workmanship or materials, then the customer will be responsible for the cost of any necessary repairs. Some problems that are outside the scope of this warranty are: • Problems due to improper maintenance or handling, carelessness, or other reasons where the customer is determined to be responsible. • Problems due to additions or modifications made to a Yaskawa product without Yaskawa’s understanding. • Problems due to the use of a Yaskawa product under conditions that do not meet the recom- mended specifications. • Problems caused by natural disaster or fire. • Or other problems not due to defects in Yaskawa workmanship or materials. Warranty service is only applicable within Japan. However, after-sales service is available for customers outside of Japan for a reasonable fee. Contact your local Yaskawa representative for more information. Exceptions Any inconvenience to the customer or damage to non-Yaskawa products due to Yaskawa's defective products whether within or outside the warranty period are NOT covered by this warranty. Restrictions • The Varispeed G7 was not designed or manufactured for use in devices or systems that may directly affect or threaten human lives or health. • Customers who intend to use the product described in this manual for devices or systems relating to transportation, health care, space aviation, atomic or electric power, or underwater use must contact their Yaskawa representatives or the nearest Yaskawa sales office beforehand. • This product has been manufactured under strict quality-control guidelines. However, if this product is to be installed in any location where failure of this product could involve or result in a life-and-death situation or loss of human life or in a facility where failure may cause a serious accident or physical injury, safety devices must be installed to minimize the likelihood of any accident. viii Registered Trademarks The following registered trademarks are used in this manual. • DeviceNet is a registered trademark of the ODVA (Open DeviceNet Vendors Association, Inc.). • InterBus is a registered trademark of Phoenix Contact Co. • ControlNet is a registered trademark of ControlNet International, Ltd. • LONWORKS is a registered trademark of the Echelon. Before Reading This Manual There are places in this manual where the constants and explanations depend on the software version. Explanations for both old and new versions are provided. Parts that are shaded and parts where “PRG: 102 only” appears apply to G7-series Inverters with software version PRG: 102 and later. Parts where “PRG: 103 only” appears apply only to G7-series Inverters with software version PRG: 103. Be sure to confirm the PRG number on the Inverter’s nameplate. An example is given below. Inverter specifications G Inverter model Input specifications Output specifications Serial number O/N : S/N : UL file number FILE NO.: E131457 Lot number Mass 1020 Version of software ix Contents Safety Information ............................................................................................ii Safety Precautions ..........................................................................................iii Warning Information and Position ..................................................................vii Warranty Information..................................................................................... viii Registered Trademarks...................................................................................ix Before Reading This Manual...........................................................................ix 1 Handling Inverters ...................................................................1-1 Varispeed G7 Introduction............................................................................ 1-2 Varispeed G7 Models ..................................................................................................... 1-2 Confirmations upon Delivery ........................................................................ 1-3 Checks ........................................................................................................................... 1-3 Nameplate Information ................................................................................................... 1-3 Component Names ........................................................................................................ 1-5 Exterior and Mounting Dimensions .............................................................. 1-6 Open Chassis Inverters (IP00) ....................................................................................... 1-6 Enclosed Wall-mounted Inverters [NEMA1 (Type 1)] ..................................................... 1-7 Checking and Controlling the Installation Site.............................................. 1-9 Installation Site ............................................................................................................... 1-9 Controlling the Ambient Temperature............................................................................. 1-9 Protecting the Inverter from Foreign Matter ................................................................... 1-9 Installation Orientation and Space.............................................................. 1-10 Removing and Attaching the Terminal Cover ............................................. 1-11 Removing the Terminal Cover ...................................................................................... 1-11 Attaching the Terminal Cover ....................................................................................... 1-12 Removing/Attaching the Digital Operator and Front Cover ........................ 1-13 Inverters of 15 kW or Less ........................................................................................... 1-13 Inverters of 18.5 kW or More........................................................................................ 1-16 Removing and Attaching the Protection Cover .......................................... 1-17 Removing the Protection Cover ................................................................................... 1-17 Attaching the Protection Cover..................................................................................... 1-18 2 Wiring .......................................................................................2-1 Connections to Peripheral Devices .............................................................. 2-2 Connection Diagram .................................................................................... 2-3 Terminal Block Configuration ....................................................................... 2-5 x Wiring Main Circuit Terminals .......................................................................2-6 Applicable Wire Sizes and Closed-loop Connectors ...................................................... 2-6 Main Circuit Terminal Functions ...................................................................................2-13 Main Circuit Configurations...........................................................................................2-14 Standard Connection Diagrams.................................................................................... 2-15 Wiring the Main Circuits ................................................................................................2-16 Wiring Control Circuit Terminals .................................................................2-22 Wire Sizes and Closed-loop Connectors ......................................................................2-22 Control Circuit Terminal Functions ...............................................................................2-24 Control Circuit Terminal Connections ...........................................................................2-28 Control Circuit Wiring Precautions................................................................................2-29 Wiring Check ..............................................................................................2-30 Checks..........................................................................................................................2-30 Installing and Wiring Option Boards ...........................................................2-31 3 Option Board Models and Specifications ......................................................................2-31 Installation..................................................................................................................... 2-32 PG Speed Control Board Terminals and Specifications................................................2-33 Wiring............................................................................................................................2-35 Wiring Terminal Blocks .................................................................................................2-38 Selecting the Number of PG (Encoder) Pulses ............................................................2-39 Digital Operator and Modes................................................... 3-1 Digital Operator ............................................................................................3-2 Digital Operator Display.................................................................................................. 3-2 Digital Operator Keys...................................................................................................... 3-2 Modes...........................................................................................................3-5 4 Inverter Modes................................................................................................................ 3-5 Switching Modes............................................................................................................. 3-6 Drive Mode .....................................................................................................................3-7 Quick Programming Mode .............................................................................................. 3-8 Advanced Programming Mode .....................................................................................3-10 Verify Mode...................................................................................................................3-13 Autotuning Mode...........................................................................................................3-14 Trial Operation ........................................................................ 4-1 Overview of Trial Operation Procedure ........................................................4-2 Trial Operation Procedures...........................................................................4-3 Setting the Power Supply Voltage Jumper (400 V Class Inverters of 55 kW or Higher). 4-3 Power ON .......................................................................................................................4-3 Checking the Display Status........................................................................................... 4-4 Basic Settings .................................................................................................................4-5 Settings for the Control Methods .................................................................................... 4-7 Autotuning....................................................................................................................... 4-9 Application Settings ......................................................................................................4-16 xi No-load Operation ........................................................................................................ 4-16 Loaded Operation......................................................................................................... 4-16 Check and Recording User Constants ......................................................................... 4-17 Adjustment Suggestions ............................................................................ 4-18 5 User Constants ........................................................................5-1 User Constant Descriptions.......................................................................... 5-2 Description of User Constant Tables .............................................................................. 5-2 Digital Operation Display Functions and Levels........................................... 5-3 User Constants Settable in Quick Programming Mode.................................................. 5-4 User Constant Tables ................................................................................... 5-8 6 A: Setup Settings............................................................................................................ 5-8 b: Application Constants............................................................................................... 5-10 C: Autotuning Constants .............................................................................................. 5-21 d: Reference Constants................................................................................................ 5-27 E: Motor Constant Constants ....................................................................................... 5-33 F: Option Constants ..................................................................................................... 5-39 H: Terminal Function Constants................................................................................... 5-46 L: Protection Function Constants ................................................................................. 5-58 N: Special Adjustments ................................................................................................ 5-69 o: Digital Operator Constants ....................................................................................... 5-73 T: Motor Autotuning...................................................................................................... 5-77 U: Monitor Constants.................................................................................................... 5-78 Factory Settings that Change with the Control Method (A1-02) ................................... 5-87 Factory Settings that Change with the Inverter Capacity (o2-04)................................. 5-90 Constant Settings by Function...............................................6-1 Frequency Reference................................................................................... 6-2 Selecting the Frequency Reference Source................................................................... 6-2 Using Multi-Step Speed Operation................................................................................. 6-5 Varispeed G7 Function Block......................................................................................... 6-8 Run Command ........................................................................................... 6-10 Selecting the Run Command Source ........................................................................... 6-10 Stopping Methods ...................................................................................... 6-12 Selecting the Stopping Method when a Stop Command is Sent .................................. 6-12 Using the DC Injection Brake ....................................................................................... 6-16 Using an Emergency Stop............................................................................................ 6-17 Acceleration and Deceleration Characteristics .......................................... 6-18 Setting Acceleration and Deceleration Times............................................................... 6-18 Accelerating and Decelerating Heavy Loads (Dwell Function) .................................... 6-22 Preventing the Motor from Stalling During Acceleration (Stall Prevention During Acceleration Function)........................................................... 6-23 Preventing Overvoltage During Deceleration (Stall Prevention During Deceleration Function) .......................................................... 6-25 xii Preventing Overvoltage by Automatically Reducing the Regenerative Torque Limit (Overvoltage Inhibit Function, PRG: 102 only) ..........................................................6-26 Adjusting Frequency References ...............................................................6-28 Adjusting Analog Frequency References .....................................................................6-28 Operation Avoiding Resonance (Jump Frequency Function) ....................................... 6-31 Adjusting Frequency Reference Using Pulse Train Inputs ...........................................6-33 Speed Limit (Frequency Reference Limit Function) ...................................6-34 Limiting Maximum Output Frequency ...........................................................................6-34 Limiting Minimum Frequency........................................................................................6-34 Improved Operating Efficiency ...................................................................6-36 Reducing Motor Speed Fluctuation (Slip Compensation Function) ..............................6-36 Compensating for Insufficient Torque at Startup and Low-speed Operation (Torque Compensation) ................................................................................................6-38 Hunting-prevention Function......................................................................................... 6-40 Stabilizing Speed (Speed Feedback Detection Function) ............................................ 6-41 Machine Protection.....................................................................................6-42 Reducing Noise and Leakage Current..........................................................................6-42 Limiting Motor Torque (Torque Limit Function)............................................................. 6-46 Preventing Motor Stalling During Operation .................................................................6-49 Changing Stall Prevention Level during Operation Using an Analog Input ..................6-50 Using Frequency Detection: L4-01 to L4-05 .................................................................6-50 Detecting Motor Torque ................................................................................................6-53 Changing Overtorque and Undertorque Detection Levels Using an Analog Input .......6-56 Motor Overload Protection............................................................................................6-57 Setting Motor Protection Operation Time......................................................................6-59 Motor Overheating Protection Using PTC Thermistor Inputs........................................6-60 Limiting Motor Rotation Direction..................................................................................6-62 Continuing Operation..................................................................................6-63 Restarting Automatically After Power Is Restored........................................................ 6-63 Speed Search ...............................................................................................................6-64 Continuing Operation at Constant Speed When Frequency Reference Is Lost............6-71 Restarting Operation After Transient Fault (Auto Restart Function).............................6-72 Operation Selection After Cooling Fan Fault ................................................................6-73 Inverter Protection ......................................................................................6-74 Performing Overheating Protection on Mounted Braking Resistors .............................6-74 Reducing Inverter Overheating Pre-Alarm Warning Levels..........................................6-75 Input Terminal Functions ............................................................................6-76 Temporarily Switching Operation between Digital Operator and Control Circuit Terminals............................................................................................... 6-76 Blocking Inverter Outputs (Baseblock Commands) ......................................................6-77 Stopping Acceleration and Deceleration (Acceleration/Deceleration Ramp Hold) .......6-78 Raising and Lowering Frequency References Using Contact Signals (UP/DOWN)..... 6-79 Accelerating and Decelerating Constant Frequencies in the Analog References (+/- Speed)....................................................................................................................6-82 Hold Analog Frequency Using User-set Timing............................................................6-83 xiii Switching Operations between a Communications Option Board and Control Circuit Terminals .............................................................................................. 6-83 Jog Frequency Operation without Forward and Reverse Commands (FJOG/RJOG) . 6-84 Stopping the Inverter by Notifying Programming Device Errors to the Inverter (External Fault Function) .............................................................................................. 6-85 Output Terminal Functions ......................................................................... 6-86 Monitor Constants ...................................................................................... 6-88 Using the Analog Monitor Constants ............................................................................ 6-88 Using Pulse Train Monitor Contents............................................................................. 6-90 Individual Functions ................................................................................... 6-92 Using MEMOBUS Communications ............................................................................. 6-92 Using the Timer Function ........................................................................................... 6-105 Using PID Control....................................................................................................... 6-106 Energy-saving ............................................................................................................ 6-115 Setting Motor Constants ............................................................................................. 6-117 Setting the V/f Pattern ................................................................................................ 6-120 Torque Control ........................................................................................................... 6-127 Speed Control (ASR) Structure .................................................................................. 6-136 Increasing the Speed Reference Response (Feed Forward Control) ........................ 6-142 Droop Control Function .............................................................................................. 6-143 Zero-servo Function ................................................................................................... 6-145 Digital Operator Functions........................................................................ 6-148 Setting Digital Operator Functions ............................................................................. 6-148 Copying Constants ..................................................................................................... 6-151 Prohibiting Writing Constants from the Digital Operator ............................................. 6-156 Setting a Password .................................................................................................... 6-156 Displaying User-set Constants Only........................................................................... 6-157 Options..................................................................................................... 6-158 Performing Speed Control with PG ............................................................................ 6-158 Using Digital Output Boards ....................................................................................... 6-162 Using an Analog Reference Board............................................................................. 6-164 Using a Digital Reference Board ................................................................................ 6-165 Using Inverters for Elevating Machines.................................................... 6-170 xiv Brake ON/OFF Sequence .......................................................................................... 6-170 Stall Prevention during Deceleration .......................................................................... 6-172 Autotuning .................................................................................................................. 6-172 Braking Resistor Overheating Protection ................................................................... 6-172 Momentary Power Loss Restart ................................................................................. 6-172 Torque Limit................................................................................................................ 6-172 I/O Open-phase Protection and Overtorque Detection .............................................. 6-173 External Baseblock Signal.......................................................................................... 6-173 Acceleration/Deceleration Time.................................................................................. 6-173 Magnetic Contactor on the Inverter’s Output-side...................................................... 6-173 Control-related Adjustments....................................................................................... 6-174 Reducing Shock during Elevating Machine Start, Stop, Acceleration, and Deceleration.........................................................................................................6-176 Confirming Startup Current and Reducing Carrier Frequency....................................6-179 Overvoltage Inhibit Function ....................................................................................... 6-180 Current Alarm Function ............................................................................6-181 Peak Hold Current Monitoring Function ...................................................6-182 Maintenance Timer Display Function .......................................................6-183 Settings Required to Use Maintenance Timer Display Function.................................6-183 Settings Required After Replacement of Cooling Fan or Electrolytic Capacitor ......... 6-184 7 Troubleshooting ..................................................................... 7-1 Protective and Diagnostic Functions ............................................................7-2 Fault Detection................................................................................................................7-2 Alarm Detection ............................................................................................................7-15 Operation Errors ...........................................................................................................7-20 Errors During Autotuning .............................................................................................7-22 Errors when Using the Digital Operator Copy Function................................................7-23 Troubleshooting ..........................................................................................7-25 If Constant Constants Cannot Be Set ...........................................................................7-25 If the Motor Does Not Operate......................................................................................7-26 If the Direction of the Motor Rotation is Reversed ........................................................ 7-29 If the Motor Does Not Put Out Torque or If Acceleration is Slow ..................................7-29 If the Motor Operates Higher Than the Reference .......................................................7-29 If the Slip Compensation Function Has Low Speed Precision......................................7-30 If There is Low Speed Control Accuracy at High-speed Rotation in Open-loop Vector Control Method ................................................................................7-30 If Motor Deceleration is Slow ........................................................................................7-30 If the Motor Overheats ..................................................................................................7-31 If There is Noise When the Inverter is Started or From an AM Radio ..........................7-32 If the Ground Fault Interrupter Operates When the Inverter is Run..............................7-32 If There is Mechanical Oscillation .................................................................................7-32 If the Torque Generated for the Motor is Insufficient (Insufficient Power) .....................7-34 If the Torque Reference (U1-09) at Low Speeds in Open-loop Vector 2 Control is Large Compared to That at Medium and High Speeds ................................................7-34 If Shock Occurs Near the Speed Estimator Switching Frequency in Open-loop Vector 2 Control (PRG: 102 only) ............................................................7-34 If Torque Ripple Occurs at Very Low Speeds in Open-loop Vector 2 Control (PRG: 102 only).........................................................................................................7-35 If the Motor Rotates Even When Inverter Output is Stopped........................................7-35 If OV is Detected When the Fan is Started, or Fan Stalls .............................................7-35 If Output Frequency Does Not Rise to Frequency Reference ......................................7-35 Acoustic Noise From the Motor .................................................................................... 7-36 xv 8 Maintenance and Inspection ..................................................8-1 Maintenance and Inspection ........................................................................ 8-2 9 Outline of Warranty......................................................................................................... 8-2 Daily Inspection .............................................................................................................. 8-2 Periodic Inspection ......................................................................................................... 8-2 Periodic Maintenance of Parts ....................................................................................... 8-3 Procedure for Adjusting Constants after Replacement of Control Board ....................... 8-3 Types and Number of Cooling Fans Used in the Drive .................................................. 8-5 Cooling Fan Replacement Outline ................................................................................. 8-6 Circulation Fan Replacement Outline........................................................................... 8-16 Removing and Mounting the Control Circuit Terminal Board ....................................... 8-21 Specifications ..........................................................................9-1 Standard Inverter Specifications................................................................... 9-2 Specifications by Model.................................................................................................. 9-2 Common Specifications.................................................................................................. 9-4 Specifications of Options and Peripheral Devices........................................ 9-6 10 Appendix ................................................................................10-1 Varispeed G7 Control Methods .................................................................. 10-2 Control Methods and Features..................................................................................... 10-2 Control Methods and Applications................................................................................ 10-4 Inverter Application Precautions ................................................................ 10-6 Selection....................................................................................................................... 10-6 Installation .................................................................................................................... 10-7 Settings ........................................................................................................................ 10-7 Handling ....................................................................................................................... 10-8 Motor Application Precautions ................................................................... 10-9 Using the Inverter for an Existing Standard Motor........................................................ 10-9 Using the Inverter for Special Motors ......................................................................... 10-10 Power Transmission Mechanism (Speed Reducers, Belts, and Chains) ................... 10-10 Conformance to UL Standard................................................................... 10-11 Conformance to CE Markings .................................................................. 10-13 CE Markings ............................................................................................................... 10-13 Requirements for Conformance to CE Markings........................................................ 10-13 Wiring Examples ...................................................................................... 10-20 xvi Using a Braking Resistor Unit .................................................................................... 10-20 Using a Braking Unit and Braking Resistor Unit......................................................... 10-21 Using Braking Units in Parallel ................................................................................... 10-22 Using a Braking Unit and Three Braking Resistor Units in Parallel............................ 10-23 Using a VS Operator .................................................................................................. 10-24 Using Transistors for Input Signals and a 0-V Common in Sinking Mode with an Internal Power Supply ................................................................................................ 10-25 Using Transistors for Input Signals and a +24-V Common in Sourcing Mode............10-26 Using Transistors for Input Signals and a 0-V Common in Sinking Mode with an External Power Supply ...............................................................................................10-27 Using Contact and Open Collector Outputs................................................................10-28 User Constants .........................................................................................10-29 INDEX Revision History xvii 1 Handling Inverters This chapter describes the checks required upon receiving or installing an Inverter. Varispeed G7 Introduction ........................................... 1-2 Confirmations upon Delivery........................................1-3 Exterior and Mounting Dimensions ..............................1-6 Checking and Controlling the Installation Site .............1-9 Installation Orientation and Space .............................1-10 Removing and Attaching the Terminal Cover ............ 1-11 Removing/Attaching the Digital Operator and Front Cover .........................................................................1-13 Removing and Attaching the Protection Cover ..........1-17 Varispeed G7 Introduction Varispeed G7 Models The Varispeed-G7 Series of Inverters included two Inverters in two voltage classes: 200 V and 400 V. Maximum motor capacities vary from 0.4 to 300 kW (41 models). Table 1.1 Varispeed G7 Models Voltage Class 200 V Class 400 V Class 1-2 Maximum Motor Capacity kW Varispeed G7 Specifications (Always specify through the protective structure when ordering.) Output Capacity kVA Basic Model Number Open Chassis (IEC IP00) CIMR-G7 0.4 1.2 CIMR-G7A20P4 20P41 0.75 2.3 CIMR-G7A20P7 20P71 Enclosed Wall-mounted [IEC IP20, NEMA 1 (Type 1)] CIMR-G7A 1.5 3.0 CIMR-G7A21P5 21P51 2.2 4.6 CIMR-G7A22P2 22P21 3.7 6.9 CIMR-G7A23P7 5.5 10 CIMR-G7A25P5 7.5 13 CIMR-G7A27P5 11 19 CIMR-G7A2011 2011 15 25 CIMR-G7A2015 20151 Remove the top and bottom covers from the Enclosed Wallmounted model. 23P71 25P51 27P51 18.5 30 CIMR-G7A2018 20180 20181 22 37 CIMR-G7A2022 20220 20221 30 50 CIMR-G7A2030 20300 20301 37 61 CIMR-G7A2037 20370 20371 45 70 CIMR-G7A2045 20450 20451 55 85 CIMR-G7A2055 20550 20551 75 110 CIMR-G7A2075 20750 20751 90 140 CIMR-G7A2090 20900 - 110 160 CIMR-G7A2110 21100 0.4 1.4 CIMR-G7A40P4 40P41 40P71 - 0.75 2.6 CIMR-G7A40P7 1.5 3.7 CIMR-G7A41P5 41P51 2.2 4.7 CIMR-G7A42P2 42P21 3.7 6.9 CIMR-G7A43P7 5.5 11 CIMR-G7A45P5 7.5 16 CIMR-G7A47P5 11 21 CIMR-G7A4011 40111 15 26 CIMR-G7A4015 40151 Remove the top and bottom covers from the Enclosed Wallmount model. 43P71 45P51 47P51 18.5 32 CIMR-G7A4018 40180 40181 22 40 CIMR-G7A4022 40220 40221 30 50 CIMR-G7A4030 40300 40301 37 61 CIMR-G7A4037 40370 40371 45 74 CIMR-G7A4045 40450 40451 55 98 CIMR-G7A4055 40550 40551 75 130 CIMR-G7A4075 40750 40751 90 150 CIMR-G7A4090 40900 40901 110 180 CIMR-G7A4110 41100 41101 132 210 CIMR-G7A4132 41320 41321 41601 160 250 CIMR-G7A4160 41600 185 280 CIMR-G7A4185 41850 - 220 340 CIMR-G7A4220 42200 - 300 460 CIMR-G7A4300 43000 - Confirmations upon Delivery Confirmations upon Delivery Checks Check the following items as soon as the Inverter is delivered. Table 1.2 Checks Item Method Has the correct model of Inverter been delivered? Check the model number on the nameplate on the side of the Inverter. Is the Inverter damaged in any way? Inspect the entire exterior of the Inverter to see if there are any scratches or other damage resulting from shipping. Are any screws or other components loose? Use a screwdriver or other tools to check for tightness. If you find any irregularities in the above items, contact the agency from which you purchased the Inverter or your Yaskawa representative immediately. Nameplate Information There is a nameplate attached to the side of each Inverter. The nameplate shows the model number, specifications, lot number, serial number, and other information on the Inverter. Example Nameplate The following nameplate is an example for a standard domestic (Japan) Inverter: 3-phase, 200 VAC, 0.4 kW, IEC IP20 and NEMA 1 (Type 1) standards Inverter specifications G Inverter model Input specifications Output specifications Serial number O/N : S/N : UL file number FILE NO.: E131457 Lot number Mass 1020 Version of software Fig 1.1 Nameplate 1-3 Inverter Model Numbers The model number of the Inverter on the nameplate indicates the specification, voltage class, and maximum motor capacity of the Inverter in alphanumeric codes. CIMR - G7 A 2 0P4 Inverter Varispeed G7 No. A No. 2 4 Specification No. 0P4 0P7 to 300 Standard domestic model Voltage Class AC input, 3-phase, 200 V Max. Motor Capacity 0.4 kW 0.75 kW to 300 kW * "P" indicates the decimal point. AC input, 3-phase, 400 V Fig 1.2 Inverter Model Numbers Inverter Specifications The Inverter specifications (“SPEC”) on the nameplate indicate the voltage class, maximum motor capacity, the protective structure, and the revision of the Inverter in alphanumeric codes. 2 0P4 1 A Voltage Class No. 2 4 AC input, 3-phase, 200 V No. 0P4 0P7 to 300 Max. Motor Capacity 0.4 kW 0.75 kW to 300 kW * Design revision order AC input, 3-phase, 400 V No. 0 1 Protective Structure Open chassis (IEC IP00) Enclosed wall-mounted [IEC IP20, NEMA 1 (Type 1)] "P" indicates the decimal point. Fig 1.3 Inverter Specifications Open Chassis Type (IEC IP00) Protected so that parts of the human body cannot reach electrically charged parts from the front when the Inverter is mounted in a control panel. TERMS Enclosed Wall-mounted Type [IEC IP20, NEMA 1 (Type 1)] The Inverter is structured so that the Inverter is shielded from the exterior, and can thus be mounted to the interior wall of a standard building (not necessarily enclosed in a control panel). The protective structure conforms to the standards of NEMA 1 (Type 1) in the USA. The protective covers (see Fig. 1.4) are required for an IEC IP20 or NEMA 1 (Type 1) protective structure. 1-4 Confirmations upon Delivery Component Names The external appearance and component names of the Inverter are shown in Fig 1.4. The Inverter with the terminal cover removed is shown in Fig 1.5. Top protective cover Mounting hole Inverter cover Front cover Mounting hole Digital Operator Diecast case Terminal cover Nameplate Cooling fan Front cover Digital Operator Terminal cover Nameplate Bottom protective cover 15 kW or Less 18.5 kW or More Fig 1.4 Inverter Appearance Charge indicator Control circuit terminals Main circuit terminals Charge indicator Ground terminal 18.5 kW or More 15 kW or Less Fig 1.5 Terminal Arrangement 1-5 Exterior and Mounting Dimensions Open Chassis Inverters (IP00) Exterior diagrams of the Open Chassis Inverters are shown below. H t1 H2 H1 H 4-d W1 4-d H1 W1 D1 W H2 t1 W (5)* (5) D 200 V/400 V Class Inverters of 0.4 to 15 kW 200 V Class Inverters of 18.5 to 110 kW 400 V Class Inverters of 18.5 to 160 kW 6-d W1 H H2 H1 W2 W3 t1 W1 W D1 D 400 V Class Inverters of 185 to 300 kW Fig 1.6 Exterior Diagrams of Open Chassis Inverters 1-6 D * (10) for 200 V Class Inverters of 30 to 110 kW or 400 V Class Inverters of 55 to 160 kW. D1 3 (5)* Exterior and Mounting Dimensions Enclosed Wall-mounted Inverters [NEMA1 (Type 1)] Exterior diagrams of the Enclosed Wall-mounted Inverters [NEMA1 (Type 1)] are shown below. H Max.10 H1 H0 H2 H H0 4-d H3 W1 4-d H1 W1 t1 4 H3 W H2 t1 D1 (5)* W (5)* D1 (5) D Grommet 3 200 V/400 V Class Inverters of 0.4 to 15 kW D * (7.5) for 200 V Class Inverters of 30 to 75 kW or 400 V Class Inverters of 55 to 160 kW. 200 V Class Inverters of 18.5 to 75 kW 400 V Class Inverters of 18.5 to 160 kW Fig 1.7 Exterior Diagrams of Enclosed Wall-mounted Inverters 1-7 Table 1.3 200 VAC and 400 VAC (0.4 kW to 300 kW) Inverter Dimensions (mm) and Masses (kg) Max. AppliVoltage cable Class Motor Output W [kW] Heat Generation (W) Dimensions (mm) Open Chassis (IP00) H D W1 H1 H2 Enclosed Wall-mounted [NEMA1 (Type 1)] D1 t1 Approx. Mass W H D W1 H0 H1 H2 H3 D1 t1 Mounting Approx. Mass Holes d* Total Cooling Heat Method Exter InterGennal nal eration 0.4 0.75 1.5 157 140 280 2.2 7.5 11 200 V (3-phase) 15 22 275 450 45 55 75 90 110 375 600 8 298 328 78 100 100 250 575 12.5 130 575 885 378 445 855 140 280 2.2 15 140 4.5 39 126 266 21 254 535 24 279 615 63 86 380 7 380 809 8 258 298 328 7.5 220 450 435 250 600 575 5.5 11 15 18.5 400 V (3-phase) 22 140 280 4.5 8 75 90 110 132 160 53 136 64 186 6 187 87 274 7 263 112 375 11 473 174 647 679 257 936 62 878 362 1240 3.2 393 68 94 M10 95 4.5 10 240 350 207 216 350 335 275 450 258 220 435 7.5 100 2.3 26 279 535 258 220 450 435 325 550 283 260 535 105 37 329 635 450 725 348 325 700 12.5 3.2 130 500 850 358 370 820 109 15 4.5 575 916 378 445 855 46 91 140 127 165 175 Fan 1080 434 1514 1291 510 1801 1474 607 2081 114 2009 823 2832 2389 1194 3583 3.5 5 7 8 7.5 M5 4.5 65.5 7 78 10 100 2.3 105 453 1027 348 325 725 700 12.5 302 3.2 130 15 4.5 579 1324 378 445 916 855 46 408 140 44 49 Natural 65 33 46 79 41 49 90 76 64 140 132 79 211 311 135 446 M6 354 174 528 516 210 726 633 246 879 929 340 1269 98 1239 488 1727 99 137 175 Fan 737 285 1022 40 M10 127 393 39 21 246 116 362 39 165 504 1243 358 370 850 820 29 10 198 106 304 85 283 260 550 535 715 90 Natural 357 136 493 M6 599 242 839 59 78 240 350 207 216 335 105 M12 1660 871 2531 126 280 266 200 300 197 186 300 285 47 27 177 7 85 58 165 100 39 65.5 57 83 0 200 300 197 186 285 42 24 302 130 15 36 43 135 157 45 55 2.3 21 122 --- 30 37 78 M5 4 209 3.7 7.5 30 12.5 453 1027 348 325 725 700 3.5 59 59 65.5 207 216 350 335 150 5 177 5 0 195 400 385 3 7 108 504 1243 358 370 850 820 157 0.75 240 87 500 850 358 370 820 350 11 57 3.2 126 280 266 200 300 197 186 300 285 7 2.3 39 177 6 7.5 220 435 140 280 4 65.5 450 725 348 325 700 0.4 1.5 258 195 385 157 5 240 350 207 216 335 250 400 37 7 3 59 200 300 197 186 285 18.5 30 126 266 177 3.7 5.5 39 1554 596 2150 1928 762 2690 M12 185 2299 928 3227 2612 1105 3717 3614 1501 5115 185 220 See Table 1.4 300 * Same for Open Chassis and Enclosed Wall-mounted Inverters. Table 1.4 400 VAC (185 to 300 kW) Inverter Dimensions (mm) and Masses (kg) Voltage Class Max. Applicable Motor Output [kW] Dimensions (mm) Open Chassis (IP00) W H D W1 W2 W3 H1 H2 D1 t1 710 1305 413 540 240 270 1270 15 125.5 4.5 185 400 V (3-phase) 1-8 Approx. Mass W H D W1 W2 W3 H1 H2 D1 t1 Approx. Mass Mounting Holes d* 260 220 300 Heat Generation (W) Enclosed Wall-mounted [NEMA (Type1)] 280 916 1475 413 730 365 365 1440 15 125.5 4.5 415 --- M12 External Internal Total Heat Generation 4436 1994 6430 5329 2205 7534 6749 2941 9690 Cooling Method Fan Checking and Controlling the Installation Site Checking and Controlling the Installation Site Install the Inverter in the installation site described below and maintain optimum conditions. Installation Site Install the Inverter under the following conditions and a pollution level of 2 or less (UL standard). Table 1.5 Installation Site Type Ambient Operating Temperature Humidity Enclosed wall-mounted -10 to + 40 °C 95% RH or less (no condensation) Open chassis -10 to + 45 °C 95% RH or less (no condensation) Protection covers are attached to the top and bottom of the Inverter. Be sure to remove the protection covers before installing a 200 or 400 V Class Inverter with an output of 15 kW or less in a panel. Refer to Page 1-17 on how to remove the protection covers. Observe the following precautions when mounting the Inverter. • Install the Inverter in a clean location free from oil mist and dust. It can be installed in a totally enclosed panel that is completely shielded from floating dust. • When installing or operating the Inverter, always take special care so that metal powder, oil, water, or other foreign matter does not get into the Inverter. • Do not install the Inverter on combustible material, such as wood. • Install the Inverter in a location free from radioactive materials and combustible materials. • Install the Inverter in a location free from harmful gasses and liquids. • Install the Inverter in a location without excessive oscillation. • Install the Inverter in a location free from chlorides. • Install the Inverter in a location not in direct sunlight. Controlling the Ambient Temperature To enhance the reliability of operation, the Inverter should be installed in an environment free from extreme temperature increases. If the Inverter is installed in an enclosed environment, such as a box, use a cooling fan or air conditioner to maintain the internal air temperature below 45°C. Protecting the Inverter from Foreign Matter Place a cover over the Inverter during installation to shield it from metal powder produced by drilling. Always remove the cover from the Inverter after completing installation. Otherwise, ventilation will be reduced, causing the Inverter to overheat. 1-9 Installation Orientation and Space Install the Inverter vertically so as not to reduce the cooling effect. When installing the Inverter, always provide the following installation space to allow normal heat dissipation. B mm min. A mm min. Air 30 mm min. 30 mm min. 120 mm min. Air Horizontal Space Vertical Space 200 V Class Inverters of 110 kW or 400 V Class Inverters of 160 to 220 kW*: A = 120, B = 120 400 V Class Inverters of 300 kW*: A = 300, B = 300 All other Inverters*: A = 50, B = 120 *If, however, there is a fan in the top of the control panel with sufficient exhaust capacity, the following dimensions may be used: A = 50, B = 120. Fig 1.8 Inverter Installation Orientation and Space IMPORTANT 1-10 1. The same space is required horizontally and vertically for both Open Chassis (IP00) and Enclosed Wallmounted [IP20, NEMA 1 (Type 1)] Inverters. 2. Always remove the protection covers before installing a 200 or 400 V Class Inverter with an output of 15 kW or less in a panel. Refer to Page 1-17 on how to remove the protection covers. Always provide enough space for suspension eye bolts and the main circuit lines when installing a 200 or 400 V Class Inverter with an output of 18.5 kW or more in a panel. Removing and Attaching the Terminal Cover Removing and Attaching the Terminal Cover Remove the terminal cover to wire cables to the control circuit and main circuit terminals. Removing the Terminal Cover Inverters of 15 kW or Less Loosen the screws at the bottom of the terminal cover, press in on the sides of the terminal cover in the direction indicated by arrow 1, and then lift the terminal cover up to an angle of about 30 degrees in the direction indicated by arrow 2. Remove the terminal cover in the direction indicated by arrow 3. 1 2 Approx. 30° 1 3 Fig 1.9 Removing the Terminal Cover (Model CIMR-G7A23P7 Shown Above) Inverters of 18.5 kW or More Loosen the screws on the left and right at the top of the terminal cover, pull out the terminal cover in the direction of arrow 1 and then lift up on the terminal in the direction of arrow 2. 1 2 Fig 1.10 Removing the Terminal Cover (Model CIMR-G7A2018 Shown Above) 1-11 Attaching the Terminal Cover When wiring the terminal block has been completed, attach the terminal cover by reversing the removal procedure. For Inverters with an output of 15 kW or less, insert the tab on the top of the terminal cover into the grove on the Inverter and press in on the bottom of the terminal cover until it clicks into place. 1-12 Removing/Attaching the Digital Operator and Front Cover Removing/Attaching the Digital Operator and Front Cover The methods of removing and attaching the Digital Operator and Front Cover are described in this section. Inverters of 15 kW or Less To attach optional boards or change the terminal board connector, remove the Digital Operator and front cover in addition to the terminal cover. Always remove the Digital Operator from the front cover before removing the terminal cover. The removal and attachment procedures are given below. Removing the Digital Operator Press the lever on the side of the Digital Operator in the direction of arrow 1 to unlock the Digital Operator and lift the Digital Operator in the direction of arrow 2 to remove the Digital Operator as shown in the following illustration. 2 1 Fig 1.11 Removing the Digital Operator (Model CIMR-G7A43P7 Shown Above) 1-13 Removing the Front Cover Press the left and right sides of the front cover in the directions of arrows 1 and lift the bottom of the cover in the direction of arrow 2 to remove the front cover as shown in the following illustration. 1 1 2 Fig 1.12 Removing the Front Cover (Model CIMR-G7A43P7 Shown Above) Mounting the Front Cover After wiring the terminals, mount the front cover to the Inverter by performing in reverse order to the steps to remove the front cover. 1. Do not mount the front cover with the Digital Operator attached to the front cover; otherwise, Digital Operator may malfunction due to imperfect contact. 2. Insert the tab of the upper part of the front cover into the groove of the Inverter and press the lower part of the front cover onto the Inverter until the front cover snaps shut. Mounting the Digital Operator After attaching the front cover, mount the Digital Operator onto the Inverting using the following procedure. 1. Hook the Digital Operator at A (two locations) on the front cover in the direction of arrow 1 as shown in the following illustration. 2. Press the Digital Operator in the direction of arrow 2 until it snaps in place at B (two locations). 1-14 Removing/Attaching the Digital Operator and Front Cover A 1 B 2 Fig 1.13 Mounting the Digital Operator IMPORTANT 1. Do not remove or attach the Digital Operator or mount or remove the front cover using methods other than those described above, otherwise the Inverter may break or malfunction due to imperfect contact. 2. Never attach the front cover to the Inverter with the Digital Operator attached to the front cover. Imperfect contact can result. Always attach the front cover to the Inverter by itself first, and then attach the Digital Operator to the front cover. 1-15 Inverters of 18.5 kW or More For Inverter with an output of 18.5 kW or more, remove the terminal cover and then use the following procedures to remove the Digital Operator and front cover. Removing the Digital Operator Use the same procedure as for Inverters with an output of 18.5 kW or less. Removing the Front Cover Lift up at the location label 1 at the top of the control circuit terminal board in the direction of arrow 2. 2 1 Fig 1.14 Removing the Front Cover (Model CIMR-G7A2018 Shown Above) Attaching the Front Cover After completing required work, such as mounting an optional board or setting the control circuit terminal board, attach the front cover by reversing the procedure to remove it. 1. Confirm that the Digital Operator is not mounted on the front cover. Contact faults can occur if the cover is attached while the Digital Operator is mounted to it. 2. Insert the tab on the top of the front cover into the slot on the Inverter and press in on the cover until it clicks into place on the Inverter. Attaching the Digital Operator Use the same procedure as for Inverters with an output of 15 kW or less. 1-16 Removing and Attaching the Protection Cover Removing and Attaching the Protection Cover Inverters of 15 kW or less have protection covers on the top and bottom as shown in Fig. 1.4.Always remove the protection covers before installing an Inverter of 15 kW or less in a panel. Use the following procedure to remove and attach a protection cover. Removing the Protection Cover Top Protection Cover Insert the tip of the straightedge screwdriver in the slot. Then, lift the cover up in the direction shown by the arrow to remove it. Slot Fig 1.15 Removing the Top Protection Cover (Model CIMR-G7A43P7 Shown Above) Bottom Protection Cover 1. Remove the terminal cover as described on Page 1-11. 2. Loosen the two screws, and remove the protection cover. 3. Return the screws to their original position and tighten (them). 4. Reattach the terminal cover as described on Page 1-12. Terminal Cover Screws Bottom Protection Cover Fig 1.16 Removing the Bottom Protection Cover (Model CIMR-G7A43P7 Shown Above) 1-17 Attaching the Protection Cover Top Protection Cover The protection cover has four hooks: two hooks on the bottom and two on the sides. Fit the bottom hooks into the holes, bend the cover slightly, and press the cover down until the hooks on the side snap. Holes for bottom hooks Fig 1.17 Attaching the Top Protection Cover (Model CIMR-G7A43P7 Shown Above) Bottom Protection Cover To attach the bottom protection cover, reverse the procedure used to remove it. 1-18 2 Wiring This chapter describes wiring terminals, main circuit terminal connections, main circuit terminal wiring specifications, control circuit terminals, and control circuit wiring specifications. Connections to Peripheral Devices..............................2-2 Connection Diagram ....................................................2-3 Terminal Block Configuration .......................................2-5 Wiring Main Circuit Terminals ......................................2-6 Wiring Control Circuit Terminals ................................ 2-22 Wiring Check .............................................................2-30 Installing and Wiring Option Boards ..........................2-31 Connections to Peripheral Devices Examples of connections between the Inverter and typical peripheral devices are shown in Fig 2.1. Power supply Molded-case circuit breaker or ground fault interrupter Magnetic contactor (MC) AC reactor for power factor improvement Zero phase reactor Braking resistor Input noise filter Inverter DC reactor for power factor improvement Varispeed F7 Ground Output noise filter Zero phase reactor Motor Ground Fig 2.1 Example Connections to Peripheral Devices 2-2 Connection Diagram Connection Diagram The connection diagram of the Inverter is shown in Fig 2.2. When using the Digital Operator, the motor can be operated by wiring only the main circuits. Thermal switch contact Braking Unit 3 (optional) +1 MC ON Thermal relay trip contact for Braking Resistor Unit 1 2 Thermal relay trip contact for motor cooling fan Forward Run/Stop S1 Reverse Run/Stop S2 CIMR-G7A2018 IM FW U V V/T2 IM W W/T3 PG-B2 (optional) Thermal switch contact for Braking Unit THRX External fault SA TA1 1 C H B G A F 2 3 3 4 5 S3 4 6 TA3 S4 TRX SA 2 S6 Jog frequency selection S7 Multi-function contact inputs Factory settings External baseblock command S8 MP Multi-step speed reference 3 S9 AC Multi-step speed reference 4 S10 Acc/dec time 1 S11 Emergency stop (NO) S12 Pulse monitor output 30 mA max. Pulse A 3 MA Fault contact D 1 S5 Multi-step speed reference 2 4 Pulse B Wiring distance: d : 30 m max. Pulse train output 0 to 32 kHz (2.2 kΩ) Default: Output frequency Ammeter adjustment 20 kΩ Multi-function analog output 2 -10 to 10 V 2 mA AM CN5 (NPN setting) Default: Output current 0 to +10 V AM +24V 8mA Ammeter adjustment 20 kΩ FM SC AC +24V E (G) Pulse train input RP Frequency setting 2 k Ω adjustment 3 2kΩ 0 to 10 V 2 1 4 to 20 mA P 0 to 10 V Shield wire connection terminal Master speed pulse train 0 to 32 kHz (3 kΩ) High level: 3.5 to 13.2 V input P P +V Frequency setting power +15 V, 20 mA A1 A2 Master speed reference 0 to 10 V (20 kΩ) Master speed reference 4 to 20 mA (250 Ω) [0 to 10 V (20 kΩ) input] A3 Multi-function anlog input 0 to 10 V (20 kΩ) AC 0V MA MEMOBUS communications RS-485/422 ( M1 M2 P1 Default: Output frequency 0 to +10 V MCC Error contact output 250 VAC, 10 mA min. Min. load 1 A max. 30 VAC, 10 mA min. 5 VDC, 10 mA 1 A max. Multi-function contact oputput 250 VAC, 10 mA min. 1 A max. Min. load 30 VAC, 10 mA min. 1 A max. 5 VDC, 10 mA Open collector 1 Default: Zero speed PC R+ R- P3 S+ C3 S- P4 IG Multi-function analog output 1 -10 to 10 V 2 mA Default: Running signal P2 Terminating resistance MAA MB Factory setting: Auxiliary frequency command -V (15V 20mA) FM E(G) MC Frequency setter PG Shieded twisted-pair wires TA2 Multi-step speed reference 1 (Main speed switching) g)) TRX External frequency references Cooling fan (Ground to 100 max.) SA 2 MCC Motor FV MC Fault reset MC B Braking Resistor Unit (optional) FU U/T1 T/L3 MC 1 Inverter S/L2 2 P - +3 R/L1 OFF -0 - 3-phase power R 200 to 240 V S 50/60 Hz T 2MCCB THRX 1 +0 Level detector FU FV FW 1MCCB 4 + 2MCCB Thermal relay trip contact C4 Open collector 2 Default: Frequency agree signal Open collector 3 Multi-function open-collector outputs 48 VDC 50 mA max. Factory setting: Inverter operation ready Open collector 4 Factory setting: minor fault Fig 2.2 Connection Diagram (Model CIMR-G7A2018 Shown Above) 2-3 1. Control circuit terminals are arranged as shown below. IMPORTANT 2. The output current capacity of the +V and −V terminals are 20 mA. Do not short-circuit between the +V, −V, and AC terminals. Doing so may result in a malfunction or a breakdown of the Inverter. 3. Disable the stall prevention during deceleration (set constant L3-04 to 0) when using a Braking Resistor Unit. If this user constant is not changed to disable stall prevention, the system may not stop during deceleration. 4. Main circuit terminals are indicated with double circles and control circuit terminals are indicated with single circles. 5. The wiring for a motor with a cooling fan is not required for self-cooling motors. 6. PG circuit wiring (i.e., wiring to the PG-B2 Board) is not required for control without a PG. 7. Sequence input signals S1 to S12 are labeled for sequence connections (0 V common and sinking mode) for no-voltage contacts or NPN transistors. These are the default settings. For PNP transistor sequence connections (+24V common and sourcing mode) or to provide a 24-V external power supply, refer to Table 2.13. 8. The multi-function analog output is a dedicated meter output for an analog frequency meter, ammeter, voltmeter, wattmeter, etc. Do not use this output for feedback control or for any other control purpose. 9. DC reactors to improve the input power factor are built into 200 V Class Inverters for 18.5 to 110 kW and 400 V Class Inverters for 18.5 to 300 kW. A DC reactor is thus an option only for Inverters for 15 kW or less. 10.Set constant L8-01 to 1 when using a breaking resistor (model ERF). When using a Braking Resistor Unit, a shutoff sequence for the power supply must be made using a thermal relay trip. 11.The minimum permissible load of a multi-function contact output and an error contact output is 10 mA. Use a multi-function open-collector output for a load less than 10 mA. 12.Do not ground nor connect the AC terminal on the control circuit to the unit. Doing so may result in a malfunction or a breakdown of the Inverter. 13.If turning off the power only for the main circuit but leaving the power ON for the control circuit, use a separate power supply for the control circuit and a specially designed Inverter, which are sold as options. 14. 2-4 indicates shield wire and P indicates twisted-pair shield wire. Terminal Block Configuration Terminal Block Configuration The terminal arrangement for 200 V Class Inverters are shown in Fig 2.3 and Fig 2.4. Control circuit terminals Main circuit terminals Charge indicator Ground terminal Fig 2.3 Terminal Arrangement (200 V Class Inverter for 0.4 kW Shown Above) Control circuit terminals Charge indicator Main circuit terminals Ground terminal Fig 2.4 Terminal Arrangement (200 V Class Inverter for 18.5 kW Shown Above) 2-5 Wiring Main Circuit Terminals Applicable Wire Sizes and Closed-loop Connectors Select the appropriate wires and crimp terminals from to Table 2.3. Refer to instruction manual TOBPC72060000 for wire sizes for Braking Resistor Units and Braking Units. Table 2.1 200 V Class Wire Sizes Inverter Model CIMR- Terminal Symbol R/L1, S/L2, T/L3, U/T1, V/T2, W/T3 , G7A20P4 R/L1, S/L2, T/L3, U/T1, V/T2, W/T3 , G7A20P7 R/L1, S/L2, T/L3, U/T1, V/T2, W/T3 , G7A21P5 R/L1, S/L2, T/L3, U/T1, V/T2, W/T3 , G7A22P2 R/L1, S/L2, T/L3, U/T1, V/T2, W/T3 , G7A23P7 R/L1, S/L2, T/L3, U/T1, V/T2, W/T3 , G7A25P5 R/L1, S/L2, T/L3, U/T1, V/T2, W/T3 , G7A27P5 R/L1, S/L2, T/L3, V/T2, W/T3 , G7A2011 1, 1, 1, 1, 1, 1, 1, , 1, 2-6 M4 1.2 to 1.5 2 to 5.5 (14 to 10) 2 (14) M4 1.2 to 1.5 2 to 5.5 (14 to 10) 2 (14) M4 1.2 to 1.5 2 to 5.5 (14 to 10) 3.5 (12) M4 1.2 to 1.5 2 to 5.5 (14 to 10) 5.5 (10) M5 2.5 8 to 14 (8 to 6) 8 (8) M5 2.5 14 (6) 14 (6) M6 4.0 to 5.0 22 (4) M5 2.5 M6 4.0 to 5.0 M8 9.0 to 10.0 M5 2.5 22 to 30 (4 to 3) 8 to 14 (8 to 6) 22 (4) 22 to 38 (4 to 2) 8 to 14 (8 to 6) 22 (4) 30 to 60 (3 to 1) 8 to 22 (8 to 4) 22 to 38 (4 to 2) 50 to 60 (1 to 1/0) 8 to 22 (8 to 4) 22 to 38 (4 to 2) 2, B1, B2, 2, B1, B2, 2, B1, B2, 2, B1, B2, 2, U/T1, 2, U/T1, B1, B2 3 3 2 (14) 2, B1, B2, R/L1, S/L2, T/L3, , 1 U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L31 G7A2022 2 to 5.5 (14 to 10) M4 2, B1, B2, R/L1, S/L2, T/L3, , 1, U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L31 G7A2018 1.2 to 1.5 Tightening Torque (N•m) 2, B1, B2, B1, B2 R/L1, S/L2, T/L3, V/T2, W/T3 G7A2015 1, mm2(AWG) Recommended Wire Size mm2 (AWG) Terminal Screws M6 4.0 to 5.0 M8 9.0 to 10.0 M6 4.0 to 5.0 M8 9.0 to 10.0 M8 9.0 to 10.0 M6 4.0 to 5.0 M8 9.0 to 10.0 Possible Wire Sizes 22 (4) 30 (3) 22 (4) 30 (3) 22 (4) 50 (1) 22 (4) Wire Type Power cables, e.g., 600 V vinyl power cables Wiring Main Circuit Terminals Table 2.1 200 V Class Wire Sizes (Continued) Inverter Model CIMR- Terminal Symbol R/L1, S/L2, T/L3, , 1 U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L31 G7A2030 3 r/ 1, / 2 R/L1, S/L2, T/L3, , 1 U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L31 G7A2037 3 r/ 1, , M4 1.3 to 1.4 M10 17.6 to 22.5 M8 8.8 to 10.8 8.8 to 10.8 M10 17.6 to 22.5 / 2 M4 1.3 to 1.4 1 M12 31.4 to 39.2 M10 17.6 to 22.5 M8 8.8 to 10.8 / 2 , 1 3 / 2 , 1 U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L31 3 r/ 1, 17.6 to 22.5 M8 R/L1, S/L2, T/L3, G7A2090 M10 17.6 to 22.5 U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L31 r/ 1, 8.8 to 10.8 M10 R/L1, S/L2, T/L3, G7A2075 M8 1.3 to 1.4 3 r/ 1, 17.6 to 22.5 M4 / 2 R/L1, S/L2, T/L3, U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L31 G7A2055 M10 17.6 to 22.5 3 r/ 1, Tightening Torque (N•m) M10 R/L1, S/L2, T/L3, , 1, U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L31 G7A2045 Terminal Screws / 2 M12 17.6 to 22.5 M4 1.3 to 1.4 M12 31.4 to 39.2 M12 31.4 to 39.2 M8 8.8 to 10.8 Possible Wire Sizes mm2(AWG) 60 to 100 (2/0 to 4/0) 5.5 to 22 (10 to 4) 30 to 60 (2 to 2/0) 0.5 to 5.5 (20 to 10) 80 to 125 (3/0 to 250) 5.5 to 22 (10 to 4) 38 to 60 (1 to 2/0) 0.5 to 5.5 (20 to 10) 50 to 100 (1/0 to 4/0) 5.5 to 60 (10 to 2/0) 30 to 60 (3 to 4/0) 0.5 to 5.5 (20 to 10) 80 to 125 (3/0 to 250) 80 to 100 (3/0 to 4/0) 5.5 to 60 (10 to 2/0) 80 to 200 (2/0 to 400) 0.5 to 5.5 (20 to 10) 150 to 200 (250 to 350) 100 to 150 (4/0 to 300) 5.5 to 60 (10 to 2/0) 60 to 150 (2/0 to 300) 0.5 to 5.5 (20 to 10) M12 31.4 to 39.2 M4 1.3 to 1.4 M12 31.4 to 39.2 200 to 325 (350 to 600) M12 31.4 to 39.2 150 to 325 (300 to 600) M8 8.8 to 10.8 M12 31.4 to 39.2 M4 1.3 to 1.4 5.5 to 60 (10 to 2/0) 150 (300) 0.5 to 5.5 (20 to 10) Recommended Wire Size mm2 (AWG) Wire Type 60 (2/0) 30 (2) 1.25 (16) 80 (3/0) 38 (1) 1.25 (16) 50 × 2P (1/0 × 2P) 50 (1/0) 1.25 (16) 80 × 2P (3/0 × 2P) 80 × 2P (3/0 × 2P) 80 (2/0) 1.25 (16) 150 × 2P (250 × 2P) 100 × 2P (4/0 × 2P) Power cables, e.g., 600 V vinyl power cables 60 × 2P (2/0 × 2P) 1.25 (16) 200 × 2P, or 50 × 4P (350 × 2P, or 1/0 × 4P) 150 × 2P, or 50 × 4P (300 × 2P, or 1/0 × 4P) 150 × 2P (300 × 2P) 1.25 (16) 2-7 Table 2.1 200 V Class Wire Sizes (Continued) Inverter Model CIMR- Terminal Symbol R/L1, S/L2, T/L3, G7A2110 , 1 U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/ L31 3 r/ 1, / 2 * The wire thickness is set for copper wires at 75°C. 2-8 Terminal Screws Tightening Torque (N•m) Possible Wire Sizes mm2(AWG) M12 31.4 to 39.2 200 to 325 (350 to 600) M12 31.4 to 39.2 150 to 325 (300 to 600) M8 8.8 to 10.8 M12 31.4 to 39.2 M4 1.3 to 1.4 5.5 to 60 (10 to 2/0) 150 (300) 0.5 to 5.5 (20 to 10) Recommended Wire Size mm2 (AWG) 200 × 2P, or 50 × 4P (350 × 2P, or 1/0 × 4P) 150 × 2P, or 50 × 4P (300 × 2P, or 1/0 × 4P) 150 × 2P (300 × 2P) 1.25 (16) Wire Type Power cables, e.g., 600 V vinyl power cables Wiring Main Circuit Terminals Table 2.2 400 V Class Wire Sizes Inverter Model CIMR- Terminal Symbol R/L1, S/L2, T/L3, U/T1, V/T2, W/T3 , G7A40P4 R/L1, S/L2, T/L3, U/T1, V/T2, W/T3 , G7A40P7 R/L1, S/L2, T/L3, U/T1, V/T2, W/T3 , G7A41P5 , G7A42P2 R/L1, S/L2, T/L3, U/T1, V/T2, W/T3 R/L1, S/L2, T/L3, U/T1, V/T2, W/T3 , G7A43P7 R/L1, S/L2, T/L3, U/T1, V/T2, W/T3 , G7A45P5 R/L1, S/L2, T/L3, U/T1, V/T2, W/T3 , G7A47P5 R/L1, S/L2, T/L3, U/T1, V/T2, W/T3 , G7A4011 R/L1, S/L2, T/L3, V/T2, W/T3 G7A4015 G7A4018 G7A4022 , 1, 1, 1, 1, 1, 1, 1, 1, 1, 2 (14) M4 1.2 to 1.5 2 to 5.5 (14 to 10) 2 (14) M4 1.2 to 1.5 2 to 5.5 (14 to 10) 2 (14) M4 1.2 to 1.5 2 to 5.5 (14 to 10) 3.5 (12) 2 (14) M4 1.2 to 1.5 2 to 5.5 (14 to 10) 3.5 (12) M4 1.2 to 1.5 3.5 to 5.5 (12 to 10) 5.5 (10) M5 2.5 5.5 to 14 (10 to 6) 8 (8) M5 2.5 M5 (M6) 2.5 (4.0 to 5.0) M5 4.0 to 5.0 M5 2.5 M5 (M6) 4.0 to 5.0 M6 4.0 to 5.0 M8 9.0 to 10.0 M6 4.0 to 5.0 M8 9.0 to 10.0 M8 9.0 to 10.0 8 (8) 5.5 (10) 8 (8) 8 (8) 8 (8) 14 (6) 14 (6) 22 (4) 22 (4) 38 (2) M6 4.0 to 5.0 M8 9.0 to 10.0 M8 9.0 to 10.0 M6 4.0 to 5.0 M8 9.0 to 10.0 8 to 14 (8 to 6) 5.5 to 14 (10 to 6) 8 to 14 (8 to 6) 8 (8) 8 to 22 (8 to 4) 14 to 22 (6 to 4) 14 to 38 (6 to 2) 22 (4) 22 to 38 (4 to 2) 22 to 60 (4 to 1/0) 8 to 22 (8 to 4) 22 to 38 (4 to 2) 30 to 60 (2 to 1/0) 8 to 22 (8 to 4) 22 to 38 (4 to 2) 2, B1, B2, Possible Wire Sizes 2, B1, B2, 2, B1, B2, 2, B1, B2, 2, B1, B2, 2, B1, B2, 2, U/T1, B1, B2 R/L1, S/L2, T/L3, , 1, 3, U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L31 R/L1, S/L2, T/L3, , 1, 3, U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L31 3 3 2 to 5.5 (14 to 10) M4 2, B1, B2, R/L1, S/L2, T/L3, , 1, U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L31 G7A4037 1.2 to 1.5 Tightening Torque (N•m) 2, B1, B2, R/L1, S/L2, T/L3, , 1, U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L31 G7A4030 mm2 (AWG) Recommended Wire Size mm2 (AWG) Terminal Screws Wire Type Power cables, e.g., 600 V vinyl power cables 22 (4) 38 (2) 22 (4) 2-9 Table 2.2 400 V Class Wire Sizes (Continued) Inverter Model CIMR- Terminal Symbol R/L1, S/L2, T/L3, , 1, U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L31 G7A4045 3 R/L1, S/L2, T/L3, , 1, U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L31 G7A4055 3 r/ 1, 200/ 2200, 400/ 2400 R/L1, S/L2, T/L3, , 1, U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L31 G7A4075 3 r/ 1, 200/ 2200, 400/ 2400 R/L1, S/L2, T/L3, , 1, U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L33 G7A4090 3 r/ 1, 200/ 2200, 400/ 2400 R/L1, S/L2, T/L3, , 1, U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L33 G7A4110 3 r/ 1, 200/ 2200, 400/ 2400 R/L1, S/L2, T/L3, , 1, U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L31 G7A4132 3 r/ 1, 200/ 2200, 400/ 2400 R/L1, S/L2, T/L3, , 1, U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L31 G7A4160 3 r/ 1, 2-10 200/ 2200, 400/ 2400 Terminal Screws Tightening Torque (N•m) M8 9.0 to 10.0 M6 4.0 to 5.0 M8 9.0 to 10.0 M10 17.6 to 22.5 M8 8.8 to 10.8 M10 17.6 to 22.5 M4 1.3 to 1.4 M10 17.6 to 22.5 M8 8.8 to 10.8 M10 17.6 to 22.5 M4 1.3 to 1.4 M10 17.6 to 22.5 M8 8.8 to 10.8 M10 17.6 to 22.5 M4 1.3 to 1.4 M10 17.6 to 22.5 M8 8.8 to 10.8 M10 17.6 to 22.5 M4 1.3 to 1.4 M12 31.4 to 39.2 M8 8.8 to 10.8 M12 31.4 to 39.2 M4 1.3 to 1.4 M12 31.4 to 39.2 M8 8.8 to 10.8 M12 31.4 to 39.2 M4 1.3 to 1.4 Possible Wire Sizes mm2 (AWG) 50 to 60 (1 to 1/0) 8 to 22 (8 to 4) 22 to 38 (4 to 2) 50 to 100 (1/0 to 4/0) 5.5 to 22 (10 to 4) 38 to 60 (2 to 2/0) 0.5 to 5.5 (20 to 10) 80 to 100 (3/0 to 4/0) 8 to 22 (8 to 4) 50 to 100 (1 to 4/0) 0.5 to 5.5 (20 to 10) 50 to 100 (1/0 to 4/0) 8 to 60 (8 to 2/0) 60 to 150 (2/0 to 300) 0.5 to 5.5 (20 to 10) 60 to 100 (2/0 to 4/0) 8 to 60 (8 to 2/0) 100 to 150 (4/0 to 300) 0.5 to 5.5 (20 to 10) 80 to 200 (3/0 to 400) 8 to 60 (8 to 2/0) 50 to 150 (1/0 to 300) 0.5 to 5.5 (20 to 10) 100 to 200 (4/0 to 400) 80 to 60 (8 to 2/0) 50 to 150 (1/0 to 300) 0.5 to 5.5 (20 to 10) Recommended Wire Size mm2 (AWG) Wire Type 50 (1) 22 (4) 50 (1/0) 38 (2) 1.25 (16) 100 (4/0) 50 (1) 1.25 (16) 50 × 2P (1/0 × 2P) 60 (2/0) 1.25 (16) 80 × 2P (3/0 × 2P) 100 (4/0) 1.25 (16) 80 × 2P (3/0 × 2P) 50 × 2P (1/0 × 2P) 1.25 (16) 100 × 2P (4/0 × 2P) 50 × 2P (1/0 × 2P) 1.25 (16) Power cables, e.g., 600 V vinyl power cables Wiring Main Circuit Terminals Table 2.2 400 V Class Wire Sizes (Continued) Inverter Model CIMR- G7A4185 Terminal Screws Tightening Torque (N•m) R/L1, S/L2, T/L3 M16 78.4 to 98 U/T1, V/T2, W/T3 R1/L11, S1/L21, T1/L33 M16 78.4 to 98 M16 78.4 to 98 M16 78.4 to 98 Terminal Symbol , 1, 3 M16 78.4 to 98 M4 1.3 to 1.4 R/L1, S/L2, T/L3 M16 78.4 to 98 U/T1, V/T2, W/T3 R1/L11, S1/L21, T1/L33 M16 78.4 to 98 M16 78.4 to 98 M16 78.4 to 98 r/ 1, G7A4220 , 200/ 2200, 400/ 2400 1, 3 mm2 (AWG) 100 to 325 (4/0 to 600) 100 to 325 (4/0 to 600) 100 to 325 (4/0 to 600) 100 to 325 (4/0 to 600) 100 to 325 (4/0 to 600) 0.5 to 5.5 (20 to 10) 100 to 325 (4/0 to 600) 100 to 325 (4/0 to 600) 100 to 325 (4/0 to 600) 100 to 325 (4/0 to 600) 100 to 325 (4/0 to 600) 0.5 to 5.5 (20 to 10) M16 78.4 to 98 M4 1.3 to 1.4 R/L1, S/L2, T/L3 M16 78.4 to 98 100 to 325 (4/0 to 600) U/T1, V/T2, W/T3 R1/L11, S1/L21, T1/L33 M16 78.4 to 98 100 to 325 (4/0 to 600) M16 78.4 to 98 M16 78.4 to 98 r/ 1, G7A4300 Possible Wire Sizes , 200/ 2200, 400/ 2400 1, 3 r/ 1, 200/ 2200, 400/ 2400 100 to 325 (4/0 to 600) 100 to 325 (4/0 to 600) M16 78.4 to 98 100 to 325 (4/0 to 600) M4 1.3 to 1.4 0.5 to 5.5 (20 to 10) Recommended Wire Size mm2 (AWG) Wire Type 150 × 2P (300 × 2P) 125 × 2P (250 × 2P) 200 × 2P (400 × 2P) 150 (300) 1.25 (16) 200 × 2P (400 × 2P) 150 × 2P (350 × 2P) 250 × 2P (500 × 2P) 200 (400) 1.25 (16) 325 × 2P (600 × 2P), 125 × 4P (250 × 4P) 325 × 2P (600 × 2P), 125 × 4P (250 × 4P) 200 × 4P (400 × 4P) Power cables, e.g., 600 V vinyl power cables 125 × 2P (250 × 2P), 325 (600) 1.25 (16) * The wire thickness is set for copper wires at 75°C. 2-11 Table 2.3 Closed-loop Connector Sizes (JIS C2805) (200 V Class and 400 V Class) Wire Thickness (mm2) Terminal Screws Size M3.5 1.25 to 3.5 M4 1.25 to 4 M3.5 1.25 to 3.5 M4 1.25 to 4 M3.5 1.25 to 3.5 M4 1.25 to 4 M3.5 2 to 3.5 M4 2 to 4 M5 2 to 5 M6 2 to 6 M8 2 to 8 M4 5.5 to 4 M5 5.5 to 5 M6 5.5 to 6 M8 5.5 to 8 M5 8 to 5 M6 8 to 6 M8 8 to 8 M6 14 to 6 M8 14 to 8 M6 22 to 6 M8 22 to 8 M8 38 to 8 M8 60 to 8 M10 60 to 10 0.5 0.75 1.25 2 3.5/5.5 8 14 22 30/38 50/60 80 M10 100 100 100 to 10 100 to 12 150 M12 200 325 80 to 10 150 to 12 200 to 12 M12 x 2 325 to 12 M16 325 to 16 Determine the wire size for the main circuit so that line voltage drop is within 2% of the rated voltage. Line voltage drop is calculated as follows: IMPORTANT 2-12 Line voltage drop (V) = 3 x wire resistance (W/km) x wire length (m) x current (A) x 10-3 Wiring Main Circuit Terminals Main Circuit Terminal Functions Main circuit terminal functions are summarized according to terminal symbols in Table 2.4. Wire the terminals correctly for the desired purposes. Table 2.4 Main Circuit Terminal Functions (200 V Class and 400 V Class) Purpose Main circuit power input Inverter outputs DC power input Terminal Symbol R/L1, S/L2, T/L3 20P4 to 2110 40P4 to 4300 R1/L11, S1/L21, T1/L31 2018 to 2110 4018 to 4300 U/T1, V/T2, W/T3 20P4 to 2110 40P4 to 4300 20P4 to 2110 40P4 to 4300 20P4 to 2015 40P4 to 4015 20P4 to 2015 40P4 to 4015 2018 to 2110 4018 to 4300 20P4 to 2110 40P4 to 4300 1, Braking Resistor Unit connecB1, B2 tion DC reactor connection 1, Braking Unit connection 3, Ground Note The 1 and Model: CIMR-G7A 200 V Class 400 V Class 2 input terminals for the DC power do not conform to UL/cUL standards. 2-13 Main Circuit Configurations The main circuit configurations of the Inverter are shown in Fig 2.5. Table 2.5 Inverter Main Circuit Configurations 200 V Class 400 V Class CIMRG7A40P4 to 4015 CIMR-G7A20P4 to 2015 B1 B2 B1 B2 +1 +1 +2 +2 R/L1 S/L2 T/L3 U/T1 U/T1 V/T2 W/T3 R/L1 S/L2 T/L3 V/T2 W/T3 − − Power supply Control circuits Power supply Cooling fan is provided for Inverters of 2.2 kW or more. Control circuits Cooling fan is provided for Inverters of 1.5 kW or more. CIMR-G7A2018, 2022 CIMR-G7A4018 to 4045 +3 +3 +1 +1 R/L1 S/L2 T/L3 R1/L11 S1/L21 T1/L31 U/T1 V/T2 W/T3 − Power supply R/L1 U/T1 S/L2 T/L3 R1/L11 S1/L21 T1/L31 − V/T2 W/T3 Power supply Control circuits CIMR-G7A2030 to 2110 Control circuits CIMR-G7A4055 to 4300 +3 +1 a b a b R/L1 S/L2 T/L3 R1/L11 S1/L21 T1/L31 − r/ l 1 a b Power supply 200/ l 2200 Control circuits 400/ l 2400 U/T1 V/T2 W/T3 * a b Power supply Control circuits Note Consult your Yaskawa representative before using 12-phase rectification. * These terminals are wired before shipment. When using DC power for the main circuit power supply, remove the wires between R-r/ for 200 V Class Inverters, input 200 VAC to r/ 1400/ 2400. 2-14 / 2, or, for 400 V Class Inverters, input either 200 VAC to r/ 1- 1 and S- / 2, then, 200/ 2200 or 400 VAC to r/ 1- Wiring Main Circuit Terminals Standard Connection Diagrams Standard Inverter connection diagrams are shown in Fig 2.5. These are the same for both 200 V Class and 400 V Class Inverters. The connections depend on the Inverter capacity. CIMR-G7A20P4 to 2015 and 40P4 to 4015 CIMR-G7A2018, 2022, and 4018 to 4045 Braking Resistor Unit (optional) Braking Resistor Unit (optional) DC reactor (optional) 3-phase 200 VAC (400 VAC) − + 1 + 2 B1 B2 R/L1 U/T1 S/L2 V/T2 T/L3 W/T3 Braking Unit (optional) IM 3-phase 200 VAC (400 VAC) Be sure to remove the short-circuit bar before connecting the DC reactor. +1 R/L1 S/L2 T/L3 R1/L11 S1/L21 T1/L31 +3 − U/T1 V/T2 W/T3 IM The DC reactor is built in. When connecting a separately-installed type Braking Unit (model CDBR), connect the B1 terminal of the Inverter to the + terminal of the Braking Unit and connect the − terminal of the Inverter to the − terminal of the Braking Unit. The B2 terminal is not used in this case. IMPORTANT CIMR-G7A2030 to 2110 3-phase 200 VAC +1 R/L1 S/L2 T/L3 R1/L11 S1/L21 T1/L31 CIMR-G7A4055 to 4300 Braking Resistor Unit (optional) Braking Resistor Unit (optional) Braking Unit (optional) Braking Unit (optional) +3 − U/T1 V/T2 W/T3 IM 3-phase 400 VAC r/l1 /l2 +1 +3 − R/L1 U/T1 S/L2 V/T2 T/L3 W/T3 R1/L11 S1/L21 T1/L31 r/l1 200/l2200 400/l2400 IM Control power is supplied internally from the main circuit DC power supply for all Inverter models. Fig 2.5 Main Circuit Terminal Connections IMPORTANT If a Braking Unit or a Braking Resistor Unit is connected to a wrong terminal, the Inverter, Braking Unit, or Braking Resistor Unit can be damaged. Refer to FOR VARISPEED-600 SERIES INVERTER BRAKING UNIT BRAKING RESISTOR UNIT INSTRUCTIONS (TOBPC720600000) for connecting the Inverter with a Braking Unit or a Braking Resistor Unit. 2-15 Wiring the Main Circuits This section describes wiring connections for the main circuit inputs and outputs. Wiring Main Circuit Inputs Observe the following precautions for wiring the main circuit power supply inputs. Installing a Molded-case Circuit Breaker Always connect the power input terminals (R, S, and T) and power supply via a molded-case circuit breaker (MCCB) suitable for the Inverter. • Choose an MCCB with a capacity of 1.5 to 2 times the Inverter's rated current. • For the MCCB's time characteristics, be sure to consider the Inverter's overload protection (one minute at 150% of the rated output current). • If the same MCCB is to be used for more than one Inverter, or other devices, set up a sequence so that the power supply will be turned OFF by a fault output, as shown in Fig 2.6. Inverter Power supply R/L1 20P4 to 2030: 3-phase, 200 to 240 VAC, 50/60 Hz 2037 to 2110: 3-phase, 200 to 230 VAC, 50/60 Hz 40P4 to 4300: 3-phase, 380 to 460 VAC, 50/60 Hz S/L2 T/L3 Fault output (NC) * For 400 V Class Inverters, connect a 400/200 V transformer. Fig 2.6 MCCB Installation Installing a Ground Fault Interrupter Inverter outputs use high-speed switching, so high-frequency leakage current is generated. At the Inverter primary side, use a ground fault interrupter for Inverters with a countermeasure against high frequency to detect only the leakage current in the frequency range that is hazardous to humans and to ignore high-frequency leakage current. Use one or several ground fault interrupters with a total cumulative sensitivity amperage of at least 30 mA per Inverter. Using a ground fault interrupter without a countermeasure against high frequency may result in a malfunction caused by high-frequency leakage current. If a ground fault interrupter without a countermeasure malfunctions, replace it with a ground fault interrupter with a countermeasure against high frequency or reduce the carrier frequency of the Inverter. Alternatively, use one or several ground fault interrupters with a total cumulative sensitivity amperage of at least 200 mA per Inverter. 2-16 Wiring Main Circuit Terminals Installing a Magnetic Contactor If the power supply for the main circuit is to be shut off during a sequence, a magnetic contactor can be used. When a magnetic contactor is installed on the primary side of the main circuit to forcibly stop the Inverter, however, the regenerative braking does not work and the Inverter will coast to a stop. • The Inverter can be started and stopped by opening and closing the magnetic contactor on the primary side. Frequently opening and closing the magnetic contactor, however, may cause the Inverter to break down. Start and stop the Inverter at most once every 30 minutes. • When the Inverter is operated with the Digital Operator, automatic operation cannot be performed after recovery from a power interruption. • If the Braking Resistor Unit is used, program the sequence so that the magnetic contactor is turned OFF by the contact of the Unit's thermal overload relay. Connecting Input Power Supply to the Terminal Block Input power supply can be connected to any terminal R, S or T on the terminal block; the phase sequence of input power supply is irrelevant to the phase sequence. Installing an AC Reactor or DC Reactor If the Inverter is connected to a large-capacity power transformer (600 kW or more) or the phase advancing capacitor is switched, an excessive peak current may flow through the input power circuit, causing the converter unit to break down. To prevent this, install an optional AC Reactor on the input side of the Inverter or a DC reactor to the DC reactor connection terminals. This also improves the power factor on the power supply side. Installing a Surge Absorber Always use a surge absorber or diode for inductive loads near the Inverter. These inductive loads include magnetic contactors, electromagnetic relays, solenoid valves, solenoids, and magnetic brakes. Installing a Noise Filter on Power Supply Side Install a noise filter to eliminate noise transmitted between the power line and the Inverter. • Correct Noise Filter Installation Power supply MCCB Noise filter Inverter IM MCCB Other controllers Use a special-purpose noise filter for Inverters. Fig 2.7 Correct Power supply Noise Filter Installation 2-17 • Incorrect Noise Filter Installation Power supply MCCB Inverter MCCB Power supply Generalpurpose noise filter IM Other controllers MCCB Generalpurpose noise filter Inverter IM MCCB Other controllers Do not use general-purpose noise filters. No generalpurpose noise filter can effectively suppress noise generated from the Inverter. Fig 2.8 Incorrect Power supply Noise Filter Installation Wiring the Output Side of Main Circuit Observe the following precautions when wiring the main output circuits. Connecting the Inverter and Motor Connect output terminals U, V, and W to motor lead wires U, V, and W, respectively. Check that the motor rotates forward with the Forward Run Command. Switch over any two of the output terminals to each other and reconnect if the motor rotates in reverse with the Forward Run Command. Never Connect a Power Supply to Output Terminals Never connect a power supply to output terminals U, V, and W. If voltage is applied to the output terminals, the internal circuits of the Inverter will be damaged. Never Short or Ground Output Terminals If the output terminals are touched with bare hands or the output wires come into contact with the Inverter casing, an electric shock or grounding will occur. This is extremely hazardous. Do not short the output wires. Do Not Use a Phase Advancing Capacitor or Noise Filter Never connect a phase advancing capacitor or LC/RC noise filter to an output circuit. The high-frequency components of the Inverter output may result in overheating or damage to these part or may result in damage to the Inverter or cause other parts to burn. Do Not Use a Magnetic Contactor Never connect a magnetic contactor between the Inverter and motor and turn it ON or OFF during operation. If the magnetic contactor is turned ON while the Inverter is operating, a large inrush current will be created and the overcurrent protection in the Inverter will operate. When using a magnetic contactor to switch to a commercial power supply, stop the Inverter and motor before operating the magnetic contactor. Use the speed search function if the magnetic contactor is operated during 2-18 Wiring Main Circuit Terminals operation. If measures for momentary power interrupts are required, use a delayed release the magnetic contactor. Installing a Thermal Overload Relay This Inverter has an electronic thermal protection function to protect the motor from overheating. If, however, more than one motor is operated with one Inverter or a multi-polar motor is used, always install a thermal relay (THR) between the Inverter and the motor and set L1-01 to 0 (no motor protection). The sequence should be designed so that the contacts of the thermal overload relay turn OFF the magnetic contactor on the main circuit inputs. Installing a Noise Filter on Output Side Connect a noise filter to the output side of the Inverter to reduce radio noise and inductive noise. Power supply MCCB Noise filter Inverter IM Radio noise Signal line Inductive noise AM radio Controller Inductive Noise: Electromagnetic induction generates noise on the signal line, causing the controller to malfunction. Radio Noise: Electromagnetic waves from the Inverter and cables cause the broadcasting radio receiver to make noise. Fig 2.9 Installing a Noise Filter on the Output Side Countermeasures Against Inductive Noise As described previously, a noise filter can be used to prevent inductive noise from being generated on the output side. Alternatively, cables can be routed through a grounded metal pipe to prevent inductive noise. Keeping the metal pipe at least 30 cm away from the signal line considerably reduces inductive noise. Power supply Metal pipe MCCB Inverter IM 30 cm min. Signal line Controller Fig 2.10 Countermeasures Against Inductive Noise 2-19 Countermeasures Against Radio Interference Radio noise is generated from the Inverter as well as from the input and output lines. To reduce radio noise, install noise filters on both input and output sides, and also install the Inverter in a totally enclosed steel box. The cable between the Inverter and the motor should be as short as possible. Power supply Steel box Metal pipe MCCB Noise filter Inverter Noise filter IM Fig 2.11 Countermeasures Against Radio Interference Cable Length between Inverter and Motor If the cable between the Inverter and the motor is long, the high-frequency leakage current will increase, causing the Inverter output current to increase as well. This may affect peripheral devices. To prevent this, adjust the carrier frequency (set in C6-02) as shown in Table 2.6. (For details, refer to Chapter 5 User Constants.) Table 2.6 Cable Length between Inverter and Motor Cable length 50 m max. 100 m max. More than 100 m Carrier frequency 15 kHz max. 10 kHz max. 5 kHz max. Ground Wiring Observe the following precautions when wiring the ground line. • Always use the ground terminal of the 200 V Inverter with a ground resistance of less than 100 Ω and that of the 400 V Inverter with a ground resistance of less than 10 Ω. • Do not share the ground wire with other devices, such as welding machines or power tools. • Always use a ground wire that complies with technical standards on electrical equipment and minimize the length of the ground wire. Leakage current flows through the Inverter. Therefore, if the distance between the ground electrode and the ground terminal is too long, potential on the ground terminal of the Inverter will become unstable. • When using more than one Inverter, be careful not to loop the ground wire. OK NO Fig 2.12 Ground Wiring 2-20 Wiring Main Circuit Terminals Connecting the Braking Resistor (ERF) A Braking Resistor that mounts to the Inverter can be used with 200 V and 400 V Class Inverters with outputs from 0.4 to 3.7 kW. Connect the braking resistor as shown in Fig 2.13. Table 2.7 L8-01 (Protect selection for internal DB resistor) 1 (Enables overheat protection) L3-04 (Stall prevention selection during deceleration) (Select either one of them.) 0 (Disables stall prevention function) 3 (Enables stall prevention function with braking resistor) Inverter Braking resistor Fig 2.13 Connecting the Braking Resistor The braking resistor connection terminals are B1 and B2. Do not connect to any other terminals. Connecting to any terminals other than B1 or B2 can cause the resistor to overheat, resulting in damage to the equipment. IMPORTANT Connecting the Braking Resistor Unit (LKEB) and Braking Unit (CDBR) Use the following settings when using a Braking Resistor Unit. Refer to Wiring Examples on page 10-20 for connection methods for a Braking Resistor Unit. A Braking Resistor that mounts to the Inverter can also be used with Inverters with outputs from 0.4 to 3.7 kW. Table 2.8 L8-01 (Protect selection for internal DB resistor) 0 (Disables overheat protection) L3-04 (Stall prevention selection during deceleration) (Select either one of them.) 0 (Disables stall prevention function) 3 (Enables stall prevention function with braking resistor) L8-01 is used when a braking resistor without thermal overload relay trip contacts (ERF type mounted to Inverter) is connected. The Braking Resistor Unit cannot be used and the deceleration time cannot be shortened by the Inverter if L304 is set to 1 (i.e., if stall prevention is enabled for deceleration). 2-21 Wiring Control Circuit Terminals Wire Sizes and Closed-loop Connectors For remote operation using analog signals, keep the control line length between the Digital Operator or operation signals and the Inverter to 50 m or less, and separate the lines from high-power lines (main circuits or relay sequence circuits) to reduce induction from peripheral devices. When setting frequencies from an external frequency setter (and not from a Digital Operator), use shielded twisted-pair wires and ground the shield to terminal E (G), as shown in the following diagram. Shield terminal E(G) 㧗V Speed setting power supply, +15 V 20 mA 2kΩ A1 Master speed reference 0 to 10 V (-10 to 10 V) 2kΩ A2 Master speed reference 4 to 20 㨙A (0 to 10 V, -10 to 10 V) 2kΩ 2kΩ A3 Auxiliary reference 0 to 10 V (-10 to 10 V) RP Pulse train input 32 kHz max. P P P P AC Analog common -V Speed setting power supply -15 V 20 mA Fig 2.14 Terminal numbers and wire sizes are shown in Table 2.9. Table 2.9 Terminal Numbers and Wire Sizes (Same for all Models) Terminals Terminal Screws FM, AC, AM, P1, P2, PC, SC, A1, A2, A3, +V, -V, S1, S2, S3, S4, S5, S6, S7, S8, MA, MB, MC, M1, M2 M3.5 P3, C3, P4, C4, MP, RP, R+, R-, S9, S10, S11, S12, S+, S-, IG E (G) Tightening Torque (N•m) 0.8 to 1.0 Possible Wire Sizes mm2(AWG) Recommended Wire Size mm2(AWG) 0.5 to 2*2 (20 to 14) 0.75 (18) *3: Phoenix 0.5 to 0.6 type M3.5 0.8 to 1.0 Single wire 0.14 to 2.5 Stranded wire: 0.14 to 1.5 (26 to 14) 0.75 (18) 0.5 to 2*2 (20 to 14) 1.25 (12) Wire Type • Shielded, twisted-pair wire*1 • Shielded, polyethylene-covered, vinyl sheath cable (KPEV-S by Hitachi Electrical Wire or equivalent) * 1. Use shielded twisted-pair cables to input an external frequency reference. * 2. Refer to Table 2.3 Closed-loop Connector Sizes (JIS C2805) (200 V Class and 400 V Class) for suitable closed-loop crimp terminal sizes for the wires. * 3. We recommend using straight solderless terminal on signal lines to simplify wiring and improve reliability. 2-22 Wiring Control Circuit Terminals Straight Solderless Terminals for Signal Lines Models and sizes of straight solderless terminal are shown in the following table. Table 2.10 Straight Solderless Terminal Sizes Wire Size mm2 (AWG) Model d1 d2 L 0.25 (24) AI 0.25 - 8YE 0.8 2 12.5 0.5 (20) AI 0.5 - 8WH 1.1 2.5 14 0.75 (18) AI 0.75 - 8GY 1.3 2.8 14 1.25 (16) AI 1.5 - 8BK 1.8 3.4 14 2 (14) AI 2.5 - 8BU 2.3 4.2 14 Manufacturer Phoenix Contact L d1 d2 Fig 2.15 Straight Solderless Terminal Sizes Wiring Method Use the following procedure to connect wires to the terminal block. 1. Loosen the terminal screws with a thin-slot screwdriver. 2. Insert the wires from underneath the terminal block. 3. Tighten the terminal screws firmly. Thin-slot screwdriver Blade of screwdriver Control circuit terminal block Strip the end for 7 mm if no solderless terminal is used. Solderless terminal or wire without soldering Wires 3.5 mm max. Blade thickness: 0.6 mm max. Fig 2.16 Connecting Wires to Terminal Block 2-23 Control Circuit Terminal Functions The functions of the control circuit terminals are shown in Table 2.11. Use the appropriate terminals for the correct purposes. Table 2.11 Control Circuit Terminals Type Sequence input signals Analog input signals No. Function Signal Level S1 Forward Run/Stop Command Forward run when ON; stopped when OFF. S2 Reverse Run/Stop Command Reverse run when ON; stopped when OFF. S3 Multi-function input 1*1 Factory setting: External fault when ON. S4 Multi-function input 2*1 Factory setting: Fault reset when ON. S5 Multi-function input 3*1 Factory setting: Multi-speed reference 1 effective when ON. S6 Multi-function input 4*1 Factory setting: Multi-speed reference 2 effective when ON. S7 Multi-function input 5*1 S8 Multi-function input 6*1 S9 Multi-function input 7*1 Factory setting: Multi-speed reference 3 effective when ON. S10 Multi-function input 8*1 Factory setting: Multi-speed reference 4 effective when ON. S11 Multi-function input 9*1 Factory setting: Acceleration/deceleration time selected when ON. S12 Multi-function input 10*1 Factory setting: Emergency stop (NO contact) when ON. SC Sequence input common +V +15 V power output +15 V power supply for analog references +15 V (Max. current: 20 mA) -V -15 V power output -15 V power supply for analog references -15 V (Max. current: 20 mA) A1 Master speed frequency reference -10 to +10 V/-100 to 100% 0 to +10 V/100% -10 to +10 V, 0 to +10 V (Input impedance: 20 kΩ) Multi-function analog input 4 to 20 mA/100%, -10 to +10 V/-100 to +100%, 0 to +10 V/100% Factory setting: Added to terminal A1 (H3-09 = 0) 4 to 20 mA (Input impedance: 250 Ω) -10 to +10 V, 0 to +10 V (Input impedance: 20 kΩ) A3 Multi-function analog input -10 to +10 V/-100 to +100%, 0 to +10 V/ 100% Factory setting: Auxiliary speed frequency reference 1 (H3-05 = 2) -10 to +10 V, 0 to +10 V (Input impedance: 20 kΩ) AC Analog reference common 0V A2 E(G) 2-24 Signal Name Shield wire, optional ground line connection point Factory setting: Jog frequency selected when ON. 24 VDC, 8 mA Photocoupler isolation Factory setting: External baseblock when ON. - - - Wiring Control Circuit Terminals Table 2.11 Control Circuit Terminals (Continued) Type Photocoupler outputs No. Signal Name Function P1 Multi-function PHC output 1 Factory setting: Zero-speed Zero-speed level (b2-01) or below when ON. P2 Factory setting: Frequency agreement detection Multi-function PHC output 2 Frequency within 2 Hz of set frequency when ON. PC Photocoupler output common for P1 and P2 P3 C3 P4 C4 MA MB Relay outputs MC M1 M2 Analog monitor outputs Pulse I/O RS485/ 422 Multi-function PHC output 3 - Signal Level 50 mA max. at 48 VDC*2 Factory setting: Ready for operation when ON. Multi-function PHC output 4 Factory setting: Minor fault. Fault output signal (NO contact) Fault when CLOSED across MA and MC Fault output signal (NC con- Fault when OPEN across MB and MC tact) Relay contact output common - Multi-function contact output Factory setting: Operating (NO contact) Operating when ON across M1 and M2. Dry contacts Contact capacity: 10 mA min. 1 A max. at 250 VAC 10 mA min. 1 A max. at 30 VDC Minimum permissible load: 5 VDC, 10 mA*4 FM Multi-function analog monitor 1 Factory setting: Output frequency 0 to 10 V/100% frequency AM Multi-function analog monitor 2 Factory setting: Current monitor 5 V/Inverter's rated current AC Analog common RP Multi-function pulse input*3 Factory setting: Frequency reference input (H6-01 = 0) 0 to 32 kHz (3 kΩ) MP Multi-function pulse monitor Factory setting: Output frequency (H6-06 = 2) 0 to 32 kHz (2.2 kΩ) R+ MEMOBUS communications input RS+ S- MEMOBUS communications output IG Communications shield wire -10 to +10 VDC ±5% 2 mA max. - For 2-wire RS-485, short R+ and S+ as well as R- and S-. - Differential input, photocoupler isolation Differential output, photocoupler isolation - * 1. For a 3-wire sequence, the default settings are a 3-wire sequence for S5, multi-step speed setting 1 for S6 and multi-step speed setting 2 for S7, and jog frequency command for S8. * 2. When driving a reactive load, such as a relay coil, always insert a flywheel diode as shown in Fig 2.17. * 3. Pulse input specifications are given in the following table. * 4. Use the photocoupler outputs when the minimum permissible load is 5 VDC or less and 10 mA or less. Low level voltage 0.0 to 0.8 V High level voltage 3.5 to 13.2 V H duty 30% to 70% Pulse frequency 0 to 32 kHz 2-25 Flywheel diode External power: 48 V max. The rating of the flywheel diode must be at least as high as the circuit voltage. Coil 50 mA max. Fig 2.17 Flywheel Diode Connection Shunt Connector CN5 and DIP Switch S1 The shunt connector CN 5 and DIP switch S1 are described in this section. CN5 O F F S1 1 2 OFF ON Terminating resistance V I Analog input switch : Factory settings Note: Refer to Table 2.12 for S1 functions and to Table 2.13 for CN5 functions. Fig 2.18 Shunt Connector CN5 and DIP Switch S1 The functions of DIP switch S1 are shown in the following table. Table 2.12 DIP Switch S1 Name Function Setting S1-1 RS-485 and RS-422 terminating resistance OFF: No terminating resistance ON: Terminating resistance of 110 Ω S1-2 Input method for analog input A2 OFF: 0 to 10 V, -10 to 10 V (internal resistance: 20 kΩ) ON: 4 to 20 mA (internal resistance: 250 Ω) Sinking/Sourcing Mode The input terminal logic can be switched between sinking mode (0-V common) and sourcing mode (+24-V common) if shunt connector CN5 is used. An external 24-V power supply is also supported, providing more freedom in signal input methods. 2-26 Wiring Control Circuit Terminals Table 2.13 Sinking/Sourcing Mode and Input Signals Internal Power Supply CN5 External Power Supply CN5 CN5 (NPN set) Factory setting Shunt position Sinking Mode IP24V (24 V) CN5 (EXT set) SC External +24 V SC S1 S1 S2 S2 CN5 CN5 CN5 (PNP set) SC Sourcing Mode IP24V (24 V) IP24V (24 V) CN5 (EXT set) External + 24 V SC S1 S1 S2 S2 IP24V (24 V) 2-27 Control Circuit Terminal Connections Connections to Inverter control circuit terminals are shown in Fig 2.19. Inverter CIMR-G7A2018 Forward Run/Stop S1 Reverse Run/Stop S2 Thermal switch contact for Braking Unit 3 4 External fault S3 Fault reset S4 Multi-step command 1 (Main speed switching) Multi-function contact input Defaults S5 Multi-step speed setting 2 S6 Jog frequency selection S7 External baseblock command S8 MP Multi-step speed setting 3 S9 AC Multi-step speed setting 4 S10 Acc/dec time 1 Default: Output frequency Ammeter adjustment AM S11 Emergency stop (NO) Pulse train output 0 to 32 kHz (2.2 kΩ) 20 kΩ − CN5 (NPN setting) +24V 8mA AM + 20 kΩ − AC Pulse train input +24V Frequency setting 2 kΩ adjustment Frequency setter External frequency references 2 kΩ 0 to 10 V 0 to 10 V MB MC 0 to 10 V (20 kΩ) A2 Master speed reference M1 M2 4 to 20 mA (250 Ω) [0 to 10 V (20 kΩ) input] P A3 P Multi-function anlog input 0 to 10 V (20 kΩ) AC -V 0V P1 Error contact output 250 VAC, 10 mA min. 1 A max. Min. load 30 VDC, 10 mA min. 1 A max. 5 VDC, 10 mA MA MC (−15V 20mA) Multi-function contact output 250 VAC, 10 mA min. 1 A max. Min. load 5 VDC, 10 mA 30 DC, 10 mA min. 1 A max. Open collector 1 Default: Zero speed P2 PC R+ R- P3 S+ C3 S- P4 IG C4 Open collector 2 Default: Frequency agree signal Open collector 3 Factory setting: Inverter operation ready Open collector 4 Factory setting: Minor fault Fig 2.19 Control Circuit Terminal Connections 2-28 Default: Output current 0 to +10 V Default: Running signal Factory setting: Auxiliary frequency command Terminating resistance MEMOBUS communications RS-485/422 MA High level: 3.5 to 13.2 V input Master speed reference A1 4 to 20 mA P -10 to 10 V 2 mA E(G) 0 to 32 kHz (3 kΩ) +15 V 20 mA 2 1 + Frequency setting power +V 3 Multi-function analog output 1 FM Shield wire connection terminal Master speed pulse train RP Default: Output current 0 to +10 V Ammeter adjustment FM SC E(G) Multi-function analog output 2 -10 to 10 V 2 mA S12 Multi-function open-collector outputs 48 VDC, 50 mA Wiring Control Circuit Terminals Control Circuit Wiring Precautions Observe the following precautions when wiring control circuits. • Separate control circuit wiring from main circuit wiring (terminals R/L1, S/L2, T/L3, B1, B2, U/T1, V/T2, W/T3, , 1, 2, and 3) and other high-power lines. • Separate wiring for control circuit terminals MA, MB, MC, M1, and M2 (contact outputs) from wiring to other control circuit terminals. • Use shielded twisted-pair cables for control circuits to prevent operating faults. Process cable ends as shown in Fig 2.20. • Connect the shield wire to terminal E (G). • Insulate the shield with tape to prevent contact with other signal lines and equipment. • Use a class 2 power supply (UL standard) when connecting to the control terminals. Shield sheath Armor Do not connect here. Connect to shield sheath ter- Insulate with tape minal at Inverter (terminal E (G)) Fig 2.20 Processing the Ends of Shielded Twisted-pair Cables 2-29 Wiring Check Checks Check all wiring after wiring has been completed. Do not perform a buzzer check on control circuits. Perform the following checks on the wiring. • Is all wiring correct? • Have any wire clippings, screws, or other foreign material been left? • Are all screws tight? • Are any wire ends contacting other terminals? 2-30 Installing and Wiring Option Boards Installing and Wiring Option Boards Option Board Models and Specifications Up to three option boards can be mounted in the Inverter. You can mount up one Board into each of the three places on the control board (A, C, and D) shown in Fig 2.21. Table 2.14 lists the type of option boards and their specifications. Table 2.14 Option Board Specifications Board Model Specifications Mounting Location PG-A2 Serial open-collector/complimentary inputs A PG-B2 Phase A/B complimentary inputs A PG-D2 Single line-driver inputs A PG-X2 Phase A/B line-driver inputs A AI-14U Input signal levels 0 to 10 V DC (20 kΩ), 1 channel 4 to 20 mA (250 Ω), 1 channel Input resolution: 14-bit C AI-14B Input signal levels 0 to 10 V DC (20 kΩ) 4 to 20 mA (250 Ω), 3 channels Input resolution: 13-bit with sign bit C DI-08 8-bit digital speed reference setting C DI-16H2 16-bit digital speed reference setting C DeviceNet Communications Board SI-N1 DeviceNet communications support C Profibus-DP Communications Board SI-P1 Profibus-DP communications support C CC-Link Communications Board SI-C CC-Link communications support C LONWORKS communications support C MECHATROLINK communications support C AO-08 8-bit analog outputs, 2 channels D AO-12 12-bit analog outputs, 2 channels D DO-08 Six photocoupler outputs and 2 relay outputs D DO-02C 2 relay outputs D PG Speed Control Boards Speed Reference Boards LONWORKS Communications Board SI-J SI-W1 MECHATROLINK CommuSI-T nication Board Analog Monitor Board Digital Output Board 2-31 Installation Before mounting an option board, remove the terminal cover and be sure that the charge indicator inside the Inverter is not lit. After confirming that the charge indicator is not lit, remove the Digital Operator and front cover and then mount the option board. The side of the front cover of the Inverter for 200/400 V Class 0.4 to 3.7 kW can be cut out as described in Fig 2.22 to make wiring of the option board easy. If the side of the front cover is cut out, the protective structure will be open chassis (IEC IP00). Refer to documentation provided with the option board for actual mounting instructions for option slots A, C, and D. Preventing C and D Option Board Connectors from Rising After installing an option board into slot C or D, insert an option clip to prevent the side with the connector from rising. The option clip can be easily removed by holding onto the protruding portion of the clip and pulling it out. Remove the option clip before installing an option board into slot C or D. The option board can not be installed completely and may not function properly if it is installed with the option clip attached. A option board mounting spacer hole 4CN A option board connector 2CN C option board connector A option board mounting spacer (Provided with A Option Board.) C option board mounting spacer C option board Option Clip (To prevent raising of C and D option boards) D option board 3CN D option board connector D option board mounting spacer A option board A option board mounting spacer Fig 2.21 Mounting Option Boards Front Cover Slit Fig 2.22 Cutting the Front Cover Cut out the slits on the front cover with nippers. Be careful to avoid injury. 2-32 Installing and Wiring Option Boards PG Speed Control Board Terminals and Specifications The terminal specifications for the PG Speed Control Boards are given in the following tables. PG-A2 The terminal specifications for the PG-A2 are given in the following table. Table 2.15 PG-A2 Terminal Specifications Terminal No. 1 2 3 TA1 4 5 Contents Power supply for pulse generator +12 V/open collector switching terminal Pulse input terminal 6 7 8 TA2 (E) Specifications 12 VDC (±5%), 200 mA max. 0 VDC (GND for power supply) Terminal for switching between12 V voltage input and open collector input. For open collector input, short across 3 and 4. H: +4 to 12 V; L: +1 V max. (Maximum response frequency: 30 kHz) Pulse input common Pulse motor output terminal 12 VDC (±10%), 20 mA max. Pulse monitor output common Shield connection terminal - PG-B2 The terminal specifications for the PG-B2 are given in the following table. Table 2.16 PG-B2 Terminal Specifications Terminal No. 1 2 3 TA1 Contents Power supply for pulse generator A-phase pulse input terminal 0 VDC (GND for power supply) H: +8 to 12 V L: +1 V max. (Maximum response frequency: 30 kHz) Pulse input common 5 H: +8 to 12 V L: +1 V max. (Maximum response frequency: 30 kHz) 1 2 3 4 TA3 12 VDC (±5%), 200 mA max. 4 B-phase pulse input terminal 6 TA2 Specifications (E) Pulse input common A-phase monitor output terminal B-phase monitor output terminal Shield connection terminal Open collector output, 24 VDC, 30 mA max. A-phase monitor output common Open collector output, 24 VDC, 30 mA max. B-phase monitor output common - 2-33 PG-D2 The terminal specifications for the PG-D2 are given in the following table. Table 2.17 PG-D2 Terminal Specifications Terminal No. Contents 1 2 12 VDC (±5%), 200 mA max.* Power supply for pulse generator 3 TA1 TA2 0 VDC (GND for power supply) 5 VDC (±5%), 200 mA max.* 4 Pulse input + terminal 5 Pulse input - terminal 6 Common terminal 7 Pulse monitor output + terminal 8 Pulse monitor output - terminal (E) Specifications Line driver input (RS-422 level input) Maximum response frequency: 300 kHz Line driver output (RS-422 level output) Shield connection terminal - * 5 VDC and 12 VDC cannot be used at the same time. PG-X2 The terminal specifications for the PG-X2 are given in the following table. Table 2.18 PG-X2 Terminal Specifications Terminal No. Contents 1 2 Power supply for pulse generator 3 TA1 TA2 TA3 A-phase + input terminal 5 A-phase - input terminal 6 B-phase + input terminal 7 B-phase - input terminal 8 Z-phase + input terminal 9 Z-phase - input terminal 10 Common terminal 1 A-phase + output terminal 2 A-phase - output terminal 3 B-phase + output terminal 4 B-phase - output terminal 5 Z-phase + output terminal 6 Z-phase - output terminal 7 Control circuit common Shield connection terminal * 5 VDC and 12 VDC cannot be used at the same time. 2-34 0 VDC (GND for power supply) 5 VDC (±5%), 200 mA max.* 4 (E) Specifications 12 VDC (±5%), 200 mA max.* Line driver input (RS-422 level input) Maximum response frequency: 300 kHz 0 VDC (GND for power supply) Line driver output (RS-422 level output) Control circuit GND - Installing and Wiring Option Boards Wiring Wiring examples are provided in the following illustrations for the option boards. Wiring the PG-A2 Wiring examples are provided in the following illustrations for the PG-A2. Three-phase, 200 VAC (400 VAC) Inverter R/L1 U/T1 S/L2 V/T2 T/L3 W/T3 PC-A2 +12 V power supply 1 2 4CN 4CN TA1 E E TA2 (E) 3 4 5 6 7 8 0 V power supply 12 V voltage input (A/B phase) Pulse 0 V Pulse monitor output Fig 2.23 Wiring a 12 V Voltage Input Three-phase, 200 VAC (400 VAC) Inverter R/L1 U/T1 S/L2 V/T2 T/L3 W/T3 PG-A2 1 2 4CN 4CN 3 TA1 E 4 5 6 E TA2 (E) 7 8 +12 V power supply 0 V power supply (Short circuit across terminals 3-4) Pulse input (+) Pulse input (-) Pulse monitor output • Shielded twisted-pair wires must be used for signal lines. • Do not use the pulse generator's power supply for anything other than the pulse generator (encoder). Using it for another purpose can cause malfunctions due to noise. • The length of the pulse generator's wiring must not be more than 100 meters. Fig 2.24 Wiring an Open-collector Input PG power supply +12 V Pulse input Short for open-collector input Pulse monitor output Pulse input Fig 2.25 I/O Circuit Configuration of the PG-A2 2-35 Wiring the PG-B2 Wiring examples are provided in the following illustrations for the PG-B2. Three-phase 200 VAC (400 VAC) Inverter Power supply +12 V Power supply 0 V A-phase pulse output (+) A-phase pulse output (-) B-phase pulse output (+) B-phase pulse output (-) A-phase pulse monitor output B-phase pulse monitor output • Shielded twisted-pair wires must be used for signal lines. • Do not use the pulse generator's power supply for anything other than the pulse generator (encoder). Using it for another purpose can cause malfunctions due to noise. • The length of the pulse generator's wiring must not be more than 100 meters. • The direction of rotation of the PG can be set in user constant F1-05. The factory preset if for forward rotation, A-phase advancement. Fig 2.26 PG-B2 Wiring A-phase pulses A-phase pulse input B-phase pulses B-phase pulse input Division rate circuit PG power supply +12 V A-phase pulse monitor output B-phase pulse monitor output • When connecting to a voltage-output-type PG (encoder), select a PG that has an output impedance with a current of at least 12 mA to the input circuit photocoupler (diode). • The pulse monitor dividing ratio can be changed using constant F1-06 (PG division rate). A-phase pulses B-phase pulses • The pulse monitor emitter is connected to common inside the PG-B2. The emitter common must be used for external circuits. Fig 2.27 I/O Circuit Configuration of the PG-B2 2-36 Installing and Wiring Option Boards Wiring the PG-D2 Wiring examples are provided in the following illustrations for the PG-D2. Inverter Three-phase 200 VAC (400 VAC) Power supply +12 V Power supply 0 V Power supply +5 V Pulse input + (A/B phase) Pulse input - (A/B phase) Pulse monitor output • Shielded twisted-pair wires must be used for signal lines. • Do not use the pulse generator's power supply for anything other than the pulse generator (encoder). Using it for another purpose can cause malfunctions due to noise. • The length of the pulse generator's wiring must not be more than 100 meters. Fig 2.28 PG-D2 Wiring Wiring the PG-X2 Wiring examples are provided in the following illustrations for the PG-X2. Three-phase 200 VAC (400 VAC) Inverter R/L1 U/T1 S/L2 V/T2 T/L3 W/T3 Power supply +12 V Power supply 0 V Power supply +5 V A-phase pulse input (+) A-phase pulse input (-) B-phase pulse input (+) B-phase pulse input (-) A-phase pulse monitor output B-phase pulse monitor output Z-phase pulse monitor output • Shielded twisted-pair wires must be used for signal lines. • Do not use the pulse generator's power supply for anything other than the pulse generator (encoder). Using it for another purpose can cause malfunctions due to noise. • The length of the pulse generator's wiring must not be more than 100 meters. • The direction of rotation of the PG can be set in user constant F1-05 (PG Rotation). The factory preset if for motor forward rotation, A-phase advancement. Fig 2.29 PG-X2 Wiring 2-37 Wiring Terminal Blocks Use no more than 100 meters of wiring for PG (encoder) signal lines, and keep them separate from power lines. Use shielded, twisted-pair wires for pulse inputs and pulse output monitor wires, and connect the shield to the shield connection terminal. Wire Sizes (Same for All Models) Terminal wire sizes are shown in Table 2.19. Table 2.19 Wire Sizes Terminal Pulse generator power supply Pulse input terminal Pulse monitor output terminal Shield connection terminal Terminal Screws Wire Thickness (mm2) - Stranded wire: 0.5 to 1.25 Single wire: 0.5 to 1.25 M3.5 0.5 to 2 Wire Type • Shielded, twisted-pair wire • Shielded, polyethylene-covered, vinyl sheath cable (KPEV-S by Hitachi Electric Wire or equivalent) Straight Solderless Terminals for Control Circuit Terminals We recommend using straight solderless terminal on signal lines to simplify wiring and improve reliability. Refer to Straight Solderless Terminal Sizes for specifications. Closed-loop Connector Sizes and Tightening Torque The closed-loop connectors and tightening torques for various wire sizes are shown in Table 2.20. Table 2.20 Closed-loop Connectors and Tightening Torques Wire Thickness [mm2] Terminal Screws 0.5 0.75 1.25 Crimp Terminal Size Tightening Torque (N • m) 1.25 - 3.5 M3.5 2 1.25 - 3.5 1.25 - 3.5 0.8 2 - 3.5 Wiring Method and Precautions The wiring method is the same as the one used for straight solderless terminals. Refer to page 2-23. Observe the following precautions when wiring. • Separate the control signal lines for the PG Speed Control Board from main circuit lines and power lines. • Connect the shield when connecting to a PG. The shield must be connected to prevent operational errors caused by noise. Also, do not use any lines that are more than 100 m long. Refer to Fig 2.20 for details on connecting the shield. • Connect the shield to the shield terminal (E). • Do not solder the ends of wires. Doing so may cause contact faults. • When not using straight solderless terminals, strip the wires to a length of approximately 5.5 mm. 2-38 Installing and Wiring Option Boards Selecting the Number of PG (Encoder) Pulses The setting for the number of PG pulses depends on the model of PG Speed Control Board being used. Set the correct number for your model. PG-A2/PG-B2 The maximum response frequency is 32,767 Hz. Use a PG that outputs a maximum frequency of approximately 20 kHz for the rotational speed of the motor. Motor speed at maximum frequency output (min−1) × PG rating (p/rev) = 20,000 Hz 60 Some examples of PG output frequency (number of pulses) for the maximum frequency output are shown in Table 2.21. Table 2.21 PG Pulse Selection Examples Motor's Maximum Speed (min−1) PG Rating (p/rev) PG Output Frequency for Maximum Frequency Output (Hz) 1800 600 18,000 1500 600 15,000 1200 900 18,000 900 1200 18,000 Note 1. The motor speed at maximum frequency output is expressed as the sync rotation speed. 2. The PG power supply is 12 V. 3. A separate power supply is required if the PG power supply capacity is greater than 200 mA. (If momentary power loss must be handled, use a backup capacitor or other method.) PG power supply Capacitor for momentary power loss Signals Fig 2.30 PG-B2 Connection Example 2-39 PG-D2/PG-X2 There are 5 V and 12 V PG power supplies. Check the PG power supply specifications before connecting. The maximum response frequency is 300 kHz. Use the following equation to computer the output frequency of the PG (fPG). fPG (Hz) = Motor speed at maximum frequency output (min−1) × PG rating (p/rev) 60 A separate power supply is required if the PG power supply capacity is greater than 200 mA. (If momentary power loss must be handled, use a backup capacitor or other method.) PG-X2 PG power supply TA1 AC IP12 1 2 IG IP5 3 A (+) 4 A (-) 5 B (+) 6 B (-) 7 0V +12V 0V Capacitor for momentary power loss +12 V + + - PG + - Z (+) 8 Z (-) IG 9 10 TA3 Fig 2.31 PG-X2 Connection Example (for 12 V PG power supply) 2-40 3 Digital Operator and Modes This chapter describes Digital Operator displays and functions, and provides an overview of operating modes and switching between modes. Digital Operator............................................................3-2 Modes ..........................................................................3-5 Digital Operator This section describes the displays and functions of the Digital Operator. Digital Operator Display The key names and functions of the Digital Operator are described below. Drive Mode Indicators (LED) FWD: Lit when there is a Forward Run Command input. REV: Lit when there is a Reverse Run Command input. SEQ: Lit when the Run Command from the control circuit terminal is enabled. REF: Lit when the frequency reference from control circuit terminals A1 and A2 is enabled. ALARM: Lit when error activated. Blinks when alarm activated. Data Display Displays monitor data, constant numbers, and settings. Frequency Ref Mode Display (Displayed at upper left of data display.) DRIVE: Lit in Drive Mode. QUICK: Lit in Quick Programming Mode. ADV: Lit in Advanced Programming Mode. VERIFY: Lit in Verify Mode. A. TUNE: Lit in Autotuning Mode. Keys Execute operations such as setting user constants, monitoring, jogging, and autotuning. Fig 3.1 Digital Operator Component Names and Functions Digital Operator Keys The names and functions of the Digital Operator Keys are described in Table 3.1. Table 3.1 Key Functions Key 3-2 Name Function LOCAL/REMOTE Key Switches between operation via the Digital Operator (LOCAL) and control circuit terminal operation (REMOTE). This Key can be enabled or disabled by setting user constant o2-01. MENU Key Selects menu items (modes). ESC Key Returns to the status before the DATA/ENTER Key was pressed. JOG Key Enables jog operation when the Inverter is being operated from the Digital Operator. Digital Operator Table 3.1 Key Functions (Continued) Key Name Function FWD/REV Key Selects the rotation direction of the motor when the Inverter is being operated from the Digital Operator. Shift/RESET Key Sets the number of digits for user constant settings. Also acts as the Reset Key when a fault has occurred. Increment Key Selects menu items, sets user constant numbers, and increments set values. Used to move to the next item or data. Decrement Key Selects menu items, sets user constant numbers, and decrements set values. Used to move to the previous item or data. DATA/ENTER Key Pressed to enter menu items, user constants, and set values. Also used to switch from one display to another. Constants cannot be changed when Undervoltage (UV) is detected. RUN Key Starts the Inverter operation when the Inverter is being controlled by the Digital Operator. STOP Key Stops Inverter operation. This Key can be enabled or disabled when operating from the control circuit terminal by setting user constant o2-02. Note Except in diagrams, Keys are referred to using the Key names listed in the above table. There are indicators on the upper left of the RUN and STOP Keys on the Digital Operator. These indicators will light and flash to indicate operating status. The RUN Key indicator will flash and the STOP Key indicator will light during initial excitation of the dynamic brake. The relationship between the indicators on the RUN and STOP Keys and the Inverter status is shown in the Fig 3.2. Inverter output frequency RUN STOP STOP Frequency setting RUN STOP Lit Blinking Not lit Fig 3.2 RUN and STOP Indicators 3-3 The following table shows the relationship between the indicators on the RUN and STOP Keys and the Inverter conditions. The indicators are lit, unlit or blinking reflecting the order of priority. Table 3.2 Relation of Inverter to RUN and STOP Indicators Priority 1 RUN STOP Indicator Indicator Inverter Status Conditions Stopped Power supply is shut down. 2 Stopped* Emergency stop • Stop Command is sent from the Digital Operator when the control circuit terminals were used to operate the Inverter. • Emergency Stop Command is sent from the control circuit terminal. Switched from LOCAL (operation using the Digital Operator) to REMOTE (operation using the control circuit terminals) when the Run Command is sent from the external terminal. Switched from the Quick or Advanced Quick programming mode to the Drive mode when the Run Command is sent from the external terminal. 3 Stopped The Inverter is run at a frequency below the minimum output frequency. The Run Command is carried out when the External Baseblock Command using the multi-function contact input terminal is issued. 4 Stopped Stopped Running During deceleration to a stop During DC injection braking when using the multi-function contact input terminal. During initial excitation of DC injection braking while the Inverter is stopped. 6 Running During emergency deceleration • Stop Command is sent from the Digital Operator when operating the Inverter using the control circuit terminals. • Emergency Stop Command is sent from the control circuit terminal. 7 Running Run Command is issued. During initial excitation of DC injection braking when starting the Inverter. 5 Note : Lit : Blinking : Not lit * If planning to run the Inverter again, first turn OFF the Run Command and Emergency Stop Command from the control circuit terminal and send the Run Command. 3-4 Modes Modes This section describes the Inverter's modes and switching between modes. Inverter Modes The Inverter's user constants and monitoring functions are organized in groups called modes that make it easier to read and set user constants.The Inverter is equipped with 5 modes. The 5 modes and their primary functions are shown in the Table 3.3. Table 3.3 Modes Mode Primary function(s) Drive mode The Inverter can be run in this mode. Use this mode when monitoring values such as frequency references or output current, displaying fault information, or displaying the fault history. Quick programming mode Use this mode to reference and set the minimum user constants to operate the Inverter (e.g., the operating environment of the Inverter and Digital Operator). Advanced programming mode Use this mode to reference and set all user constants. Verify mode Use this mode to read/set user constants that have been changed from their factoryset values. Autotuning mode* Use this mode when running a motor with unknown motor constants in the vector control method. The motor constants are calculated and set automatically. This mode can also be used to measure only the motor line-to-line resistance. * Always perform autotuning with the motor before operating using vector control. Autotuning mode will not be displayed during operation or when an error has occurred. The default setting of the Inverter is for open-loop vector 1 control (A1-02 = 2). 3-5 Switching Modes The mode selection display will appear when the MENU Key is pressed from a monitor or setting display. Press the MENU Key from the mode selection display to switch between the modes. Press the DATA/ENTER Key from the mode selection key to monitor data and from a monitor display to access the setting display. Display at Startup Rdy -DRIVE- Frequency Ref U1- 01=60.00Hz U1-02=60.00Hz U1-03=10.05A Mode Selection Display MENU Monitor Display Setting Display DATA ENTER -DRIVE- DATA ENTER -DRIVE- Monitor ** Main Menu ** Operation Rdy > RESET Rdy -DRIVE- Reference Source U1 - 01=60.00Hz U1- 01=60.00Hz U1-02=60.00Hz U1-03=10.05A U1-02=60.00Hz U1-03=10.05A ESC ESC DATA ENTER Rdy -DRIVE- Frequency Ref U1- 01=060.00Hz (0.00←→60.00) "0.00Hz" ESC MENU DATA ENTER -QUICK- ** Main Menu ** DATA ENTER -QUICK- Control Method A1-02=2 *2* Open Loop Vector Quick Setting ESC -QUICK- Control Method A1-02= 2 *2* Open Loop Vector ESC MENU DATA ENTER DATA ENTER -ADV- ** Main Menu ** > RESET -ADV- Initialization Select Language ESC -ADV- ESC -ADV- Select Language A1- 00= 0 *1* English Select Language A1- 00 =0 *1* English A1 - 00=1 Programming DATA ENTER ESC MENU DATA ENTER -VERIFY- ** Main Menu ** -VERIFY- None Modified Modified Consts The constant number will be displayed if a constant has been changed. Press the DATA/ENTER Key to enable the change. ESC MENU DATA ENTER -A.TUNE- -A.TUNE- Tuning Mode Sel T1- 01=0 1 *0* ** Main Menu ** Auto-Tuning DATA ENTER Tuning Mode Sel T1- 01= 0 *0* Standard Tuning "0" Standard Tuning "0" ESC -A.TUNE- ESC Fig 3.3 Mode Transitions IMPORTANT 3-6 When running the Inverter after using Digital Operator, press the MENU Key to select the drive mode (displayed on the LCD screen) and then press the DATA/ENTER Key from the drive mode display to bring up the monitor display. Run Commands can't be received from any other display. (Monitor display in the drive mode will appear when the power is turned ON.) Modes Drive Mode Drive mode is the mode in which the Inverter can be operated. The following monitor displays are possible in drive mode: The frequency reference, output frequency, output current, and output voltage, as well as fault information and the fault history. When b1-01 (Reference selection) is set to 0, the frequency can be changed from the frequency setting display. Use the Increment, Decrement, and Shift/RESET Keys to change the frequency. The user constant will be written and the monitor display will be returned to when the DATA/ENTER Key is pressed after changing the setting. Example Operations Key operations in drive mode are shown in the following figure. Display at Startup -DRIVE- Rdy Frequency Ref U1- 01=60.00Hz U1-02=60.00Hz U1-03=10.05A Mode Selection Display MENU Monitor Display DATA ENTER -DRIVE- A B -DRIVE- Monitor ** Main Menu ** 1 Rdy 㧪 RESET U1 - 01=60.00Hz Operation DATA ENTER Frequency Setting Display 2 Rdy -DRIVE- DATA ENTER Frequency Ref U1-02=60.00Hz U1-03=10.05A ESC -DRIVE- Rdy Frequency Ref U1- 01=60.00Hz U1- 01= 060.00Hz U1-02=60.00Hz U1-03=10.05A (0.00←→60.00) ̍0.00Hz̍ ESC MENU ESC -DRIVE- -QUICK- Monitor Rdy ** Main Menu ** U1 - 02=60.00Hz Quick Setting U1-03=10.05A U1-04= 2 㧪 RESET -DRIVE- Output Freq The Frequency Setting Display will not be displayed when using an analog reference. Rdy U1- 02=60.00Hz U1-03=10.05A U1-04= 2 ESC MENU -DRIVE- Monitor -ADV- ** Main Menu ** Programming Rdy 㧪 RESET U1 - 40 = 10H Rdy -DRIVE- FAN Elapsed Time U1- 40 = 10H U1-01=60.00Hz U1-02=60.00Hz ESC MENU DATA ENTER U1-01=60.00Hz U1-02=60.00Hz 1 2 3 4 -VERIFY- ** Main Menu ** Modified Consts MENU -A.TUNE- ** Main Menu ** Auto-Tuning -DRIVE- Fault Trace Rdy 㧪 RESET -DRIVE- Current Fault U2 - 01= Rdy U2 - 01 = U2-02= OV U2-03=60.00Hz U2-02=OV U2-03=60.00Hz ESC -DRIVE- Fault Trace Rdy 㧪 RESET -DRIVE- Last Fault Rdy The fault name will be displayed if the DATA/ENTER Key is pressed while a constant is being displayed for which a fault code is being displayed. DATA ENTER U2 - 02 = OV U3-03=60.00Hz U3-04=60.00Hz U3-03=60.00Hz U3-04=60.00Hz ESC 3 4 5 6 -DRIVE- Rdy U2 - 02= OV DC Bus Overvolt U2 - 02 = OV ESC DATA ENTER -DRIVE- Fault History Rdy 㧪 RESET -DRIVE- Last Fault Rdy U3-02= OV U3-03= OH U3-02=OV U3-03=OH ESC Rdy U3-03= OH U3-04= UV DATA ENTER Fault Message 2 ESC U3-03= OH U3-04= UV -DRIVE- Rdy U3 - 02= OV DC Bus Overvolt U3 - 02 = OV 5 A Rdy -DRIVE- U3 - 02 = OV Rdy ESC 㧪 RESET Fault Message 2 -DRIVE- U3 - 01= OC Over Current U3 - 01 = OC U3 - 01= OC -DRIVE- DATA ENTER ESC 6 B Fig 3.4 Operations in Drive Mode 3-7 Note When changing the display with the Increment and Decrement Keys, the next display after the one for the last parameter number will be the one for the first parameter number and vise versa. For example, the next display after the one for U1-01 will be U1-40. This is indicated in the figures by the letters A and B and the numbers 1 to 6. The display for the first monitor constant (frequency reference) will be displayed when power is turned ON. The monitor item displayed at startup can be set in o1-02 (Monitor Selection after Power Up). Operation cannot be started from the mode selection display. IMPORTANT Quick Programming Mode In quick programming mode, the constants required for Inverter trial operation can be monitored and set. Constants can be changed from the setting displays. Use the Increment, Decrement, and Shift/RESET Keys to change the frequency. The user constant will be written and the monitor display will be returned to when the DATA/ENTER Key is pressed after changing the setting. Refer to Chapter 5 User Constants for details on the constants displayed in quick programming mode. Example Operations Key operations in quick programming mode are shown in the following figure. 3-8 Modes Mode Selection Display Frequency Setting Display Monitor Display MENU -DRIVE- ** Main Menu ** Operation A B MENU DATA ENTER -QUICK- DATA ENTER -QUICK- Control Method A1-02=2 *2* Open Loop Vector ** Main Menu ** Quick Setting ESC ESC -QUICK- Control Method A1-02= 2 *2* Open Loop Vector MENU DATA ENTER -QUICK-ADV- ** Main Menu ** Reference Source b1-01=1 *1* Terminals ESC Programming -QUICKMENU -VERIFY- Run Source b1-02=1 *1* Terminals DATA ENTER -QUICK- Reference Source b1-01= 1 *1* Terminals -QUICK- Run Source b1-02= 1 *1* Terminals ESC ** Main Menu ** Modified Consts -QUICKMENU Terminal AM Gain DATA ENTER H4-05=0.50 -A.TUNE- ** Main Menu ** Auto-Tuning (0.00←→2.50) 0.50 -QUICK- MOL Fault Select L1-01=1 *1* Std Fan Cooled -QUICK- Terminal AM Gain H4-05= 0 .50 ESC DATA ENTER (0.00 2.50) 0.50 -QUICK- MOL Fault Select L1-01= 1 *1* Std Fan Cooled ESC -QUICK- StallP Decel Sel L3-04=1 *1* Enabled DATA ENTER -QUICK- StallP Decel Sel L3-04= 1 *1* Enabled ESC A B Fig 3.5 Operations in Quick Programming Mode 3-9 Advanced Programming Mode In advanced programming mode, all Inverter constants can be monitored and set. Constants can be changed from the setting displays. Use the Increment, Decrement, and Shift/RESET Keys to change the frequency. The user constant will be written and the monitor display will be returned to when the DATA/ENTER Key is pressed after changing the setting. Refer to Chapter 5 User Constants for details on the constants. Example Operations Key operations in advanced programming mode are shown in the following figure. Mode Selection Display Monitor Display A DATA ENTER -ADV- 1 B -ADV- Select Language ESC -ADV- -ADV- Select Language A1- 00= 0 *1* English Select Language A1- 00 =0 *1* English A1-00=1 Programming 2 DATA ENTER 㧪 RESET Initialization ** Main Menu ** Setting Display ESC ESC MENU 㧪 RESET -ADV-VERIFY- ** Main Menu ** Modified Consts Initialization DATA ENTER -ADV- Control Method A1- 02 =2 *2* Open Loop Vector A1- 02 =2 Control Method ESC -ADV- Control Method A1- 02= 2 *2* Open Loop Vector ESC MENU -A.TUNE- 1 2 3 4 ** Main Menu ** Auto-Tuning 㧪 RESET -ADV- PID Control MENU DATA ENTER -ADV- b5-01=0 b5- 01 =0 *0* b5-01= 0 *0* Disabled PID Mode -ADV- PID Mode PID Mode Disabled ESC ESC -DRIVE- ** Main Menu ** Operation MENU 㧪 RESET -ADV- DATA ENTER -ADV- -ADV- PID Control Fb los Det Time Fb los Det Time b5 - 14= 1.0Sec b5- 14= 1.0Sec b5-14=01.0Sec (0.00㨪25.5) ̍1.0Sec̍ Fb los Det Time ESC (0.00㨪25.5) ̍1.0Sec̍ ESC -QUICK- 3 4 5 6 ** Main Menu ** Quick Setting MENU 㧪 RESET -ADV- DATA ENTER -ADV- Torque Limit Fwd Torque Limit (0㨪300) ̍200%̍ Torque Limit Fwd ESC 㧪 RESET -ADV- L7- 04= 200% DATA ENTER -ADV- (0㨪300) ̍200%̍ ESC 5 6 Fig 3.6 Operations in Advanced Programming Mode 3-10 (0㨪300) ̍200%̍ -ADV- Torq Lmt Rev Rgn L7- 04= 200% Torq Lmt Rev Rgn B L7-01= 2 00% ESC Torq Lmt Rev Rgn Torque Limit A Torque Limit Fwd L7- 01= 200% L7-01=200% -ADV- L7-04= 2 00% ESC (0㨪300) ̍200%̍ Modes Setting User Constants Here, the procedure is shown to change C1-01 (Acceleration Time 1) from 10 s to 20 s. Table 3.4 Setting User Constants in Advanced Programming Mode Step No. Digital Operator Display -DRIVE- 1 Description Rdy Frequency Ref U1- 01=60.00Hz Power supply turned ON. U1-02=60.00Hz U1-03=10.05A -DRIVE- 2 ** Main Menu ** MENU Key pressed to enter drive mode. Operation -QUICK- 3 ** Main Menu ** MENU Key pressed to enter quick programming mode. Quick Setting -ADV- 4 ** Main Menu ** Programming MENU Key pressed to enter advanced programming mode. -ADV- 5 Initialization A1-00=1 DATA/ENTER pressed to access monitor display. Select Language -ADV- 6 Accel Time 1 C1-00= 10.0Sec (0.0←→6000.0) 10.0Sec Increment or Decrement Key pressed to display C1-01 (Acceleration Time 1). -ADV- 7 Accel Time 1 C1-01= 0 010.0Sec (0.0←→6000.0) 10.0Sec DATA/ENTER Key pressed to access setting display. The setting of C1-01 (10.00) is displayed. -ADV- 8 Accel Time 1 C1-01= 0 010.0Sec (0.0←→6000.0) 10.0Sec Shift/RESET Key pressed to move the flashing digit to the right. -ADV- 9 Accel Time 1 C1-01= 00 10.0Sec (0.0←→6000.0) 10.0Sec Increment Key pressed to change set value to 20.00 s. -ADV- 10 Accel Time 1 C1-01= 00 20.0Sec (0.0←→6000.0) 10.0Sec -ADV- 11 Entry Accepted DATA/ENTER Key pressed to enter the set data. “Entry Accepted” is displayed for 1.0 s after the data setting has been confirmed with the DATA/ENTER Key. -ADV- 12 Accel Time 1 C1- 01= 20.0Sec (0.0←→6000.0) 10.0Sec The monitor display for C1-01 returns. 3-11 External Fault Setting Procedure Examples of the Digital Operator displays that appear when setting an eternal error for a multi-function contact input in Advanced Programming Mode are shown in the following diagram. Mode Selection Display Monitor Display A DATA ENTER DATA ENTER -ADV- ** Main Menu ** 1 B H1-01=24 Terminal S3 Sel ESC 3 4 -ADV- -ADV- Terminal S3 Sel H1- 01 =24 *24* External Fault Digital Inputs Programming 2 DATA ENTER RESET -ADV- Setting Display "24" ESC ESC Terminal S3 Sel H1- 01= 24 *24* NO/Always Det Coast to Stop MENU RESET -ADV- Digital Inputs -VERIFY- ** Main Menu ** Modified Consts -ADV- -ADV- Terminal S4 Sel H1- 02 =14 *14* Fault Reset H1- 02 =14 Terminal S4 Sel "14" Terminal S3 Sel H1- 01= 25 *24* NC/Always Det Coast to Stop ESC MENU RESET -ADV- Digital Inputs -A.TUNE- ** Main Menu ** Auto-Tuning -ADV- -ADV- Terminal S8 Sel H1- 08 =08*08* Ext BaseBlk N.O. H1- 08 =08 Terminal S8 Sel "08" ESC MENU -ADV- 1 -DRIVE- 2 -ADV- ** Main Menu ** Operation Terminal S3 Sel H1- 01= 26 *24* NO/During RUN Coast to Stop Digital Inputs Terminal S3 Sel H1- 01= 27 *24* NC/During RUN Coast to Stop H2-01= 0 Term M1-M2 Sel MENU -ADV-QUICK- ** Main Menu ** Quick Setting Pulse I/O Setup H6-01= 0 Pulse Input Sel -ADV- MENU A B Terminal S3 Sel H1- 01= 2F *24* NC/During RUN Alarm Only 3 Fig 3.7 External Fault Function Setting Example 3-12 4 Modes Verify Mode Verify mode is used to display any constants that have been changed from their default settings in a programming mode or by autotuning. “None” will be displayed if no settings have been changed. Of the environment mode settings, only A1-02 will be displayed if it has been changed. Other environment modes settings will not be displayed even if they have been changed from their default settings. Even in verify mode, the same procedures can be used to change settings as are used in the programming modes. Use the Increment, Decrement, and Shift/RESET Keys to change the frequency. The user constant will be written and the monitor display will be returned to when the DATA/ENTER Key is pressed after changing the setting. Example Operations An example of key operations is given below for when the following settings have been changed from their default settings: b1-01 (Reference Selection), C1-01 (Acceleration Time 1), E1-01 (Input Voltage Setting), and E2-01 (Motor Rated Current). Mode Selection Display Monitor Display Setting Display DATA ENTER -ADV- ** Main Menu ** Programming A B MENU DATA ENTER -VERIFY- ** Main Menu ** -VERIFY- Reference Source b1-01=1 *1* Terminals Modified Consts "1" DATA ENTER -VERIFY- Reference Source b1-01= 1 *1* Terminals "1" ESC ESC MENU -VERIFY- Accel Time 1 -A.TUNE- ** Main Menu ** Auto-Tuning MENU DATA ENTER C1-01=200.0Sec (0.0㨪6000.0) ̍10.0Sec̍ ** Main Menu ** Operation -VERIFY- Input Voltage (155㨪255) ̍200VAC̍ -VERIFY- Motor Rated FLA MENU Accel Time 1 (0.0㨪6000.0) ̍10.0Sec̍ ESC DATA ENTER E1-01=200VAC -DRIVE- -VERIFY- C1-01=0200.0Sec Input Voltage E1-01= 200VAC ESC DATA ENTER E2-01=2.00A (0.32㨪6.40) ̍1.90A̍ -VERIFY- (155㨪255) ̍200V̍ -VERIFY- Motor Rated FLA E2-01= 2.00A ESC (0.32㨪6.40) ̍1.90A̍ -QUICK- ** Main Menu ** Quick Setting A B MENU Fig 3.8 Operations in Verify Mode 3-13 Autotuning Mode Autotuning automatically tunes and sets the required motor constants when operating in the vector control methods. Always perform autotuning before starting operation. When V/f control has been selected, stationary autotuning for only line-to-line resistance can be selected. When the motor cannot be disconnected from the load, perform stationary autotuning. Contact your Yaskawa representatives to set motor constants by calculation. The Inverter's autotuning function automatically determines the motor constants, while a servo system's autotuning function determines the size of a load, so these autotuning functions are fundamentally different. The default setting of the Inverter is for open-loop vector 1 control. Example of Operation Set the motor output power (in kW), rated voltage, rated current, rated frequency, rated speed, and number of poles specified on the nameplate on the motor and then press the RUN Key. The motor is automatically run and the motor constants measured based on these settings and autotuning will be set. Always set the above items. Autotuning cannot be started otherwise, e.g., it cannot be started from the motor rated voltage display. Constants can be changed from the setting displays. Use the Increment, Decrement, and Shift/RESET Keys to change the frequency. The user constant will be written and the monitor display will be returned to when the DATA/ENTER Key is pressed after changing the setting. The following example shows autotuning for open-loop vector control while operating the motor without switching to motor 2. 3-14 Modes Mode Selection Display Monitor Display Setting Display DATA ENTER -VERIFY- ** Main Menu ** Modified Consts A MENU DATA ENTER -A.TUNE- -A.TUNE- Tuning Mode Sel T1- 01 =0 *0* Standard Tuning ** Main Menu ** Auto-Tuning DATA ENTER "0" -A.TUNE- Tuning Mode Sel T1- 01 = 0 *0* Standard Tuning "0" ESC ESC MENU -DRIVE- ** Main Menu ** Operation MENU -QUICK- ** Main Menu ** Quick Setting -A.TUNE- DATA ENTER -A.TUNE- DATA ENTER Rated Frequency T1- 05 = 60.0Hz (0.0 400.0) 0.0Hz Rated Frequency T1- 05 = 0 60.0Hz (0.0 400.0) 0.0Hz ESC Number of Poles T1- 06 = 4 (2 48) 4 -A.TUNE- Auto-Tuning MENU -A.TUNE- Rdy ESC RUN 0.0Hz/0.0A Tuning Ready ? Press RUN key -A.TUNE- Number of Poles T1- 06 = 04 (2 48) 4 -A.TUNE- 48.0Hz/10.5A GOAL -ADV- ** Main Menu ** Programming MENU A The display will automatically change depending on the status of autotuning. Tune Proceeding 48.0Hz/10.5A START30% GOAL -A.TUNE- Tune Proceeding START -A.TUNE- Tune Proceeding 30% Tune Successful STOP -A.TUNE- Tune Aborted STOP key -A.TUNE- Tune Successful 30% * TUn10 will be displayed during rotational autotuning and TUn11 will be displayed during stationary autotuning. The DRIVE indicator will light when autotuning starts. Fig 3.9 Operation in Autotuning Mode The setting displays in for autotuning depend on the control method (V/f, V/f with PG, or open-loop vector). If a fault occurs during autotuning, refer to Chapter 7 Troubleshooting. IMPORTANT 3-15 4 Trial Operation This chapter describes the procedures for trial operation of the Inverter and provides an example of trial operation. Overview of Trial Operation Procedure........................4-2 Trial Operation Procedures..........................................4-3 Adjustment Suggestions ............................................4-18 Overview of Trial Operation Procedure Perform trial operation according to the following flowchart. START Installation Wiring Set power supply voltage.*1 Turn ON power. Confirm status. Select operating method. Basic settings (Quick programming mode) V/f control? V/f YES (Default: A1-02=0) PG? Vector (A1-02=2, 3, or 4)*5 V/f with PG (A1-02=1) Set E1-03. V/f default: 200V/60Hz(400V/60Hz) Settings according to control mode Motor cable over 50 m or heavy load possibly causing motor to stall or overload? Set E1-03, E2-04, and F1-01.*2 V/f default: 200V/60Hz (400V/60Hz) OK to operate *3 motor during autotuning? YES NO YES NO Stationary autotuning for *4 line-to-line resistance only Application settings (Advanced programming mode) Rotational autotuning Load is connected to motor when operating motor first time after autotuning? NO Stationary autotuning 1 *6 *1 Set for 400 V Class Inverter for 55 kW or more. *2 If there is a reduction gear between the motor and PG, set the reduction ratio in F1-12 and F1-13 in advanced programming mode. Optimum adjustments and constant settings *3 Use rotational autotuning to increase autotuning accuracy whenever it is okay for the motor to be operated. Check/record constants. *4 If the motor cable changes to 50 m or longer for the actual installation, perform stationary autotuning for the line-to-line resistance only on-site. *5 The default control mode is open-loop vector control 2 (A1-02 =2). *6 If the maximum output frequency is different from the base frequency, set the maximum output frequency (E1-04) after autotuning. No-load operation Loaded operation END Fig 4.1 Trial Operation Flowchart 4-2 YES Stationary autotuning 2 *6 Trial Operation Procedures Trial Operation Procedures The procedure for the trial operate is described in order in this section. Setting the Power Supply Voltage Jumper (400 V Class Inverters of 55 kW or Higher) Set the power supply voltage jumper after setting E1-01 (Input Voltage Setting) for 400 V Class Inverters of 55 kW or higher. Insert the jumper into the power tap nearest to the actual power supply voltage. If the wrong jumper is selected, the Inverter may be damaged. The jumper is factory-set to 440 V when shipped. If the power supply voltage is not 440 V, use the following procedure to change the setting. 1. Turn OFF the power supply and wait for at least 5 minutes. 2. Confirm that the CHARGE indicator has gone out. 3. Remove the terminal cover. 4. Insert the jumper at the position for the voltage supplied to the Inverter (see Fig 4.2). 5. Return the terminal cover to its original position. Power tap Jumper (factory-set position) 200 V Class power supply 400 V class power supply Power supply input terminals CHARGE indicator Fig 4.2 Power Supply Voltage Jumper Power ON Confirm all of the following items and then turn ON the power supply. • Check that the power supply is of the correct voltage. 200 V Class: 3-phase 200 to 240 VDC, 50/60 Hz 400 V Class: 3-phase 380 to 480 VDC, 50/60 Hz • Make sure that the motor output terminals (U, V, W) and the motor are connected correctly. • Make sure that the Inverter control circuit terminal and the control device are wired correctly. • Set all Inverter control circuit terminals to OFF. • When using a PG Speed Control Board, make sure that it is wired correctly. • Make sure that the motor is not connected to the mechanical system (no-load status) 4-3 Checking the Display Status If the Digital Operator's display at the time the power is connected is normal, it will read as follows: -DRIVE-DRIVE- Display for normal operation Rdy Frequency RefRef Frequency U1- 01 01= 60.0 0Hz U1-01= 0 0 0.0 0Hz U1-02=60.00Hz U1-03=10.05A The frequency reference monitor is displayed in the data display section. When an fault has occurred, the details of the fault will be displayed instead of the above display. In that case, refer to Chapter 7 Troubleshooting. The following display is an example of a display for faulty operation. -DRIVE- Display for fault operation Frequency UV Ref DC Bus Undervolt 4-4 The display will differ depending on the type of fault. A low voltage alarm is shown at left. Trial Operation Procedures Basic Settings Switch to the quick programming mode (“QUICK” will be displayed on the LCD screen) and then set the following user constants. Refer to Chapter 3 Digital Operator and Modes for Digital Operator operating procedures and to Chapter 5 User Constants and Chapter 6 Constant Settings by Function for details on the user constants. Constants that must be set are listed in Table 4.1 and those that are set according to the application are listed in Table 4.2. Table 4.1 Constants that Must Be Set Constant Number A1-02 Name Control method selection Description Set the control method for the Inverter. 0: V/f control 1: V/f control with PG 2: Open-loop vector 1 control 3: Flux vector 4: Open-loop vector 2 control Setting Range Factory Setting Page 0 to 4 2 5-8 1 5-10 6-2 6-76 6-94 0 to 3 1 5-10 6-10 6-76 6-94 Reference selection Set the frequency reference input method. 0: Digital Operator 1: Control circuit terminal (analog input) 2: MEMOBUS communications 3: Option board 4: Pulse train input b1-02 Operation method selection Set the Run Command input method. 0: Digital Operator 1: Control circuit terminal (sequence input) 2: MEMOBUS communications 3: Option board C1-01 Acceleration time Set the acceleration time in seconds for the output 1 frequency to climb from 0% to 100%. 0.0 to 6000.0 10.0 s 5-21 6-18 C1-02 Deceleration time Set the deceleration time in seconds for the output 1 frequency to fall from 100% to 0%. 0.0 to 6000.0 10.0 s 5-21 6-18 Set the Inverter's nominal input voltage in volts. Input voltage setThis setting is used as a reference value in protecting tion functions. 155 to 255 V (200 V Class) 310 to 510 V (400 V Class) 200 V (200 V Class) 400 V (400 V Class) 5-33 6-120 Motor rated current Set the motor rated current. Setting for generalpurpose 10% to 200% motor of of Inverter's rated current same capacity as Inverter Motor protection selection Set to enable or disable the motor overload protection function using the electronic thermal relay. 0: Disabled 1: General motor protection 2: Inverter motor protection 3: Vector motor protection b1-01 E1-01 E2-01 L1-01 0 to 4 0 to 3 1 5-34 6-57 6-117 5-58 6-57 4-5 Table 4.2 Constants that Are Set as Required Constant Number b1-03 C6-02 C6-11 Name Stopping method selection Description Select stopping method when Stop Command is sent. 0: Deceleration to stop 1: Coast to stop 2: DC braking stop 3: Coast to stop with timer Carrier frequency selection Carrier frequency selection for open-loop vector 2 control L3-04 4-6 Set the voltage level gain for the multi-function FM and AM ter- analog output 1 (H4-02) and 2 (H4-05). minal output gain Set the number of multiples of 10 V to be output as the 100% output for the monitor item. Stall prevention selection during deceleration Factory Setting Page 0 to 3 0 5-10 6-12 1 to F Depends on capacity, voltage, and control method. 5-26 1 to 4 Depends on kVA setting. 5-26 0 to 400.00 Hz d1-01 to d1-04: 0.00 Hz d1-17: 6.00 Hz 5-27 0.00 to 2.50 H4-02: 1.00 H4-05: 0.50 5-54 0 to 3 1 5-61 6-25 The carrier frequency is set low if the motor cable is 50 m or longer or to reduce radio noise or leakage current. Frequency referd1-01 to ences 1 to 4 and Set the required speed references for multi-step d1-04 and jog frequency ref- speed operation or jogging. d1-17 erence H4-02 and H405 Setting Range 0: Disabled (Deceleration as set. If deceleration time is too short, a main circuit overvoltage may result.) 1: Enabled (Deceleration is stopped when the main circuit voltage exceeds the overvoltage level. Deceleration restarts when voltage is returned.) 2: Intelligent deceleration mode (Deceleration rate is automatically adjusted so that the Inverter can decelerate in the shortest possible time. Set deceleration time is disregarded.) 3: Enabled (with Braking Resistor Unit) When a braking option (Braking Resistor, Braking Resistor Unit, Braking Unit) is used, always set to 0 or 3. Trial Operation Procedures Settings for the Control Methods Autotuning methods depend on the control method set for the Inverter. Make the settings required by the control method. Overview of Settings Make the required settings in quick programming mode and autotuning mode according to the following flowchart. START NO Vector control (A1-02 = 2, 3, or 4)*3 V/f control? 㧔A1-02=0 or 1) YES V/f Control mode selection PG? YES 㧔A1-02=1㧕 NO (Default: A1-02=0) Set E1-03. V/f default: 200V/60Hz(400V/60Hz) Motor cable over 50 m or heavy load possibly causing motor to stall or overload? *2 Set E1-03, E2-04, and F1-01. V/f default: 200V/60Hz(400V/60Hz) YES OK to operate motor during autotuning? *1 NO Load is connected to motor when operating motor first time after autotuning? YES YES NO Stationary autotuning for line-to-line resistance only Rotational *4 autotuning Stationary *4 autotuning 1 Stationary *4 autotuning 2 END Note If the motor cable changes to 50 m or longer for the actual installation, perform stationary autotuning for the line-to-line resistance only on-site. * 1. Use rotational autotuning to increase autotuning accuracy whenever it is okay for the motor to be operated. Always perform rotational autotuning when using open-loop vector 2 control. * 2. If there is a reduction gear between the motor and PG, set the reduction ratio in F1-12 and F1-13. * 3. The default setting of the Inverter is for open-loop vector 1 control (A1-02 = 2). * 4. If the maximum output frequency is different from the base frequency, set the maximum output frequency (E1-04) after autotuning. Fig 4.3 Settings According to the Control Method 4-7 Setting the Control Method Any of the following five control methods can be set. Control Method Constant Setting Basic Control Main Applications V/f control A1-02 = 0 Voltage/frequency ratio fixed control Variable speed control, particularly control of multiple motors with one Inverter and replacing existing Inverters V/f control with PG A1-02 = 1 Voltage/frequency ratio fixed control with speed compensation using a PG Applications requiring high-precision speed control using a PG on the machine side Open-loop vector 1 control A1-02 = 2 (factory setting) Current vector control without a PG Variable speed control, applications requiring speed and torque accuracy using vector control without a PG A1-02 = 3 Flux vector control Very high-performance control with a PG (simple servo drives, high-precision speed control, torque control, and torque limiting) A1-02 = 4 Current vector control without a PG with an ASR (speed controller) (Always perform rotational autotuning.) Very high-performance control without a PG (torque control without a PG, torque limiting, applications requiring a 1:200 speed control range without a PG) Flux vector control Open-loop vector 2 control Note With vector control, the motor and Inverter must be connected 1:1. The motor capacity for which stable control is possible is 50% to 100% of the capacity of the Inverter. V/f Control (A1-02 = 0) • Set either one of the fixed patterns (0 to E) in E1-03 (V/f Pattern Selection) or set F in E1-03 to specify a user-set pattern as required for the motor and load characteristics in E1-04 to E1-13 in advanced programming mode. Simple operation of a general-purpose motor at 50 Hz: E1-03 = 0 Simple operation of a general-purpose motor at 60 Hz: E1-03 = F (default) or 1 If E1-03 = F, the default setting in the user setting from E1-04 to E1-13 are for 60 Hz • Perform stationary autotuning for the line-to-line resistance only if the motor cable is 50 m or longer for the actual installation or the load is heavy enough to produce stalling. Refer to the following section on Autotuning for details on stationary autotuning. V/f Control with PG (A1-02=1) • Set either one of the fixed patterns (0 to E) in E1-03 (V/f Pattern Selection) or set F in E1-03 to specify a user-set pattern as required for the motor and load characteristics in E1-04 to E1-13 in advanced programming mode. Simple operation of a general-purpose motor at 50 Hz: E1-03 = 0 Simple operation of a general-purpose motor at 60 Hz: E1-03 = F (default) or 1 If E1-03 = F, the default setting in the user setting from E1-04 to E1-13 are for 60 Hz • Set the number of motor poles in E2-04 (Number of Motor Poles) • Set the number of rotations per pulse in F1-01 (PG Constant). If there is a reduction gear between the motor and PG, set the reduction ratio in F1-12 and F1-13 in advanced programming mode. 4-8 Trial Operation Procedures • Perform stationary autotuning for the line-to-line resistance only if the motor cable is 50 m or longer for the actual installation or the load is heavy enough to produce stalling. Refer to the following section on Autotuning for details on stationary autotuning. Open-loop Vector 1 Control (A1-02 = 2) Perform autotuning. If the motor can be operated, perform rotational autotuning. If the motor cannot be operated, perform stationary autotuning 1 or 2. Refer to the following section on Autotuning for details on autotuning. Flux Vector Control (A1-02 = 3) Perform autotuning. If the motor can be operated, perform rotational autotuning. If the motor cannot be operated, perform stationary autotuning 1 or 2. Refer to the following section on Autotuning for details on autotuning. Open-loop Vector 2 Control (A1-02 = 4) Perform autotuning. If the motor can be operated, perform rotational autotuning. If the motor cannot be operated, perform stationary autotuning 1 or 2. Refer to the following section on Autotuning for details on autotuning. Autotuning Use the following procedure to perform autotuning to automatically set motor constants when using the vector control method, when the cable length is long, etc. If the control method was changed after autotuning, be sure to perform autotuning again. One of the following four autotuning modes can be set. • Rotational autotuning • Stationary autotuning 1 • Stationary autotuning for line-to-line resistance only • Stationary autotuning 2 Precautions Before Using Autotuning Read the following precautions before using autotuning. • Autotuning the Inverter is fundamentally different from autotuning the servo system. Inverter autotuning automatically adjusts parameters according to detected motor constants, whereas servo system autotuning adjusts parameters according to the detected size of the load. • When speed or torque precision is required at high speeds (i.e., 90% of the rated speed or higher), use a motor with a rated voltage that is 20 V less than the input power supply voltage of the Inverter for 200Vclass Inverters and 40 V less for 400V-class Inverters. If the rated voltage of the motor is the same as the input power supply voltage, the voltage output from the Inverter will be unstable at high speeds and sufficient performance will not be possible. • Use stationary autotuning 1 or 2 whenever performing autotuning for a motor that is connected to a load. • Use rotational autotuning whenever performing autotuning for a motor that has fixed output characteris- tics, when high precision is required, or for a motor that is not connected to a load. • If rotational autotuning is performed for a motor connected to a load, the motor constants will not be found accurately and the motor may exhibit abnormal operation. Never perform rotational autotuning for a motor connected to a load. 4-9 • If the wiring between the Inverter and motor changes by 50 m or more between autotuning and motor installation, perform stationary autotuning for line-to-line resistance only. • If the motor cable is long (50 m or longer), perform stationary autotuning for line-to-line resistance only even when using V/f control. • The status of the multi-function inputs and multi-function outputs will be as shown in the following table during autotuning. When performing autotuning with the motor connected to a load, be sure that the holding brake is not applied during autotuning, especially for conveyor systems or similar equipment. Tuning Mode Multi-function Inputs Multi-function Outputs Rotational autotuning Do not function. Same as during normal operation Stationary autotuning 1 Do not function. Maintain same status as when autotuning is started. Stationary autotuning for lineto-line resistance only Do not function. Maintain same status as when autotuning is started. Stationary autotuning 2 Do not function. Maintain same status as when autotuning is started. • To cancel autotuning, always use the STOP Key on the Digital Operator. • Power will be supplied to the motor when stationary autotuning is performed even though the motor will not turn. Do not touch the motor until autotuning has been completed. Setting the Autotuning Mode Rotational Autotuning (T1-01 = 0) Rotational autotuning is used for open-loop vector control and flux vector control. Set T1-01 to 0, input the data from the nameplate, and then press the RUN Key on the Digital Operator. The Inverter will stop the motor for approximately 1 minute and then set the required motor constants automatically while operating the motor for approximately 1 minute. IMPORTANT 1. Always disconnect the motor from the machine and confirm that it is safe to operate the motor before performing rotational autotuning. 2. If the motor cannot be operated by itself, perform stationary autotuning, but always use rotational autotuning whenever it is possible to operate the motor by itself to increase performance. Stationary Autotuning 1 (T1-01 = 1) Stationary autotuning1 is used for open-loop vector control and flux vector control. Set T1-01 to 1, input the data from the nameplate, and then press the RUN Key on the Digital Operator. The Inverter will supply power to the stationary motor for approximately 1 minute and some of the motor constants will be set automatically. The remaining motor constants E2-02 (motor rated slip) and E2-03 (motor no-load current) will be set automatically the first time operation is started in drive mode. To perform an operation immediately after stationary autotuning1, use the following procedure under the recommended conditions. 1. Check the values of E2-02 and E2-03 in verify mode or advanced programming mode. 2. Run the motor once in drive mode under the following conditions. • The Inverter and the motor are connected. • The motor shaft is not locked with a mechanical brake or other stopping mechanism (or function). • A motor-load ratio of 30% or less is maintained. • A speed of 30% or more of the base frequency set at E1-06 (default = highest frequency) is maintained at a constant speed for one second or more. 4-10 Trial Operation Procedures 3. After stopping the motor, check the values of E2-02 and E2-03 again in verify mode or advanced programming mode. If the values of E2-02 and E2-03 differ from the ones before the first operation was carried out, the settings have been successfully completed. Next, check if the values are suitable or not. If the values of E2-02 and E2-03 differed greatly from the reference data of the motor in the test report or the instruction manual, hunting, motor vibrations, insufficient motor torque, or an overcurrent may occur because the motor is operated although the aforementioned conditions have not been fulfilled after stationary autotuning1. For elevators, failure to observe this caution may result in the cage falling or injury. If so, perform stationary autotuning1 again and run the motor using the aforementioned procedure under the recommended conditions or perform stationary autotuning 2 or rotational autotuning. Usually the standard setting for E2-02 is 1 Hz to 3 Hz, and that for E2-03 is 30% to 65% of the rated current for a general-purpose motor. Generally, the larger the motor capacity is, the smaller the rated slip and the ratio of the no-load current to the rated current become. Use the data given in Factory Settings that Change with the Inverter Capacity (o2-04) of Chapter 5 User Constants as a reference. IMPORTANT 1. Power will be supplied to the motor when stationary autotuning 1 is performed even though the motor will not turn. Do not touch the motor until autotuning has been completed. 2. When performing stationary autotuning 1 connected to a conveyor or other machine, ensure that the holding brake is not activated during autotuning. Stationary Autotuning for Line-to-Line Resistance Only (T1-01 = 2) Stationary autotuning for line-to-line resistance only can be used in any control method. This is the only autotuning possible for V/f control and V/f control with PG modes. Autotuning can be used to prevent control errors when the motor cable is long (50 m or longer) or the cable length has changed since installation or when the motor and Inverter have different capacities. Set T1-01 to 2, and then press the RUN Key on the Digital Operator. The Inverter will supply power to the stationary motor for approximately 20 seconds and the Motor Line-to-Line Resistance (E2-05) and cable resistance will be automatically measured. IMPORTANT 1. Power will be supplied to the motor when stationary autotuning for line-to-line resistance is performed even though the motor will not turn. Do not touch the motor until autotuning has been completed. 2. When performing stationary autotuning connected to a conveyor or other machine, ensure that the holding brake is not activated during autotuning. Stationary Autotuning 2 (T1-01 = 4) If using Inverters for applications with constant loads such as for elevators, or with a motor load ratio exceeding 30% at startup, and rotational autotuning without loads cannot be performed, perform stationary autotuning 2 (T1-01=4). Stationary autotuning 2 is used for open-loop vector control and flux vector control. Set T1-04 to 4, and Motor no-load current (T1-09) will be added as a setting item. Input the data from the nameplate. Be sure to input the value or motor no-load current (motor exciting current) from motor examination results to T1-09. After autotuning, the value of T1-09 will be written in E2-03. When not setting T1-09, the value of Yaskawa standard motor’s no-load current will be written in E2-03. IMPORTANT 1. Power will be supplied to the motor when stationary autotuning 2 is performed even though the motor will not turn. Do not touch the motor until autotuning has been completed. 2. When performing stationary autotuning 2 connected to a conveyor or other machine, ensure that the holding brake is not activated during autotuning. 4-11 Precautions for Rotational and Stationary Autotuning Lower the base voltage based on Fig 4.4 to prevent saturation of the Inverter’s output voltage when the rated voltage of the motor is higher than the voltage of the power supply to the Inverter. Use the following procedure to perform autotuning. 1. Input the voltage of the input power supply to T1-03 (Motor rated voltage). 2. Input the results of the following formula to T1-05 (Motor base frequency): (Base frequency from the motor’s nameplate × setting of T1-03)/(Rated voltage from motor’s nameplate) 3. Perform autotuning. After having completed autotuning, set E1-04 (Max. output frequency) to the base frequency shown on the motor nameplate. Output voltage Rated voltage from motor nameplate T1-03 0 Base frequency from motor nameplate ×T1-03 Output frequency Base frequency from motor nameplate Rated voltage from motor nameplate Fig 4.4 Motor Base Frequency and Inverter Input Voltage Setting IMPORTANT 1. When speed precision is required at high speeds (i.e., 90% of the rated speed or higher), set T1-03 (Motor rated voltage) to the input power supply voltage × 0.9. 2. When operating at high speeds (i.e., 90% of the rated speed or higher), the output current will increase as the input power supply voltage is reduced. Be sure to provide sufficient margin in the Inverter current. Precautions After Using Rotational and Stationary Autotuning • After completing autotuning, set E1-04 (Max. output frequency) to the base frequency from the motor’s nameplate. • In stationary autotuning 1, when the motor is first operated in the drive mode after tuning, the remaining motor constants E2-02 (Motor rated slip) and E2-03 (Motor no-load current) are set automatically. To perform an operation immediately after stationary autotuning 1, use the following procedure under the recommended conditions. 1. Check the values of E2-02 and E2-03 in verify mode or advanced programming mode. 2. Run the motor once in drive mode under the following conditions. • The Inverter and the motor are connected. • The motor shaft is not locked with a mechanical brake or other stopping mechanism (or function). • A motor-load ratio of 30% or less is maintained. • A speed of 30% or more of the base frequency set at E1-06 (default = highest frequency) is maintained at a constant speed for one second or more. 3. After stopping the motor, check the values of E2-02 and E2-03 again in verify mode or advanced programming mode. If the values of E2-02 and E2-03 differ from the ones before the first operation was carried out, the settings have been successfully completed. Next, check if the values are suitable or not. 4-12 Trial Operation Procedures If the values of E2-02 and E2-03 differed greatly from the reference data of the motor in the test report or the instruction manual, hunting, motor vibrations, insufficient motor torque, or an overcurrent may occur because the motor is operated although the aforementioned conditions have not been fulfilled after stationary autotuning 1. For elevators, failure to observe this caution may result in the cage falling or injury. If so, perform stationary autotuning 1 again and run the motor using the aforementioned procedure under the recommended conditions or perform stationary autotuning 2 or rotational autotuning. Usually the standard setting for E2-02 is 1 Hz to 3 Hz, and that for E2-03 is 30% to 65% of the rated current for a general-purpose motor. Generally, the larger the motor capacity is, the smaller the rated slip and the ratio of the no-load current to the rated current become. Use the data given in Factory Settings that Change with the Inverter Capacity (o2-04) of Chapter 5 User Constants as a reference. 4-13 Constant Settings for Autotuning The following constants must be set before autotuning. Table 4.3 Constant Settings before Autotuning Constant Number Name Display Display Motor 1/2 When switching to motor 2 is selection*1 selected, set the motor for which autotuning is to be performed. (This constant is T1-00 ignored if motor 2 is not Select selected.) Motor 1: Motor 1 2: Motor 2 Autotuning mode selection T1-01 Tuning Mode Sel Motor output power T1-02 Mtr Rated Power Motor rated voltage T1-03 Rated Voltage Motor rated curT1-04 rent Rated Current Set the autotuning mode. 0: Rotational autotuning 1: Stationary autotuning 1 2: Stationary autotuning for line-to-line resistance only 3: Shipping adjustment*8 4: Stationary autotuning 2*9 4-14 Factory Setting 1 or 2 1 Yes Yes Yes Yes Yes 0 to 4 2 (V/f) 0 (Vector) Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes *4 0.00 to 650.00 kW Set the rated voltage of the motor in volts.*5 *6 0.0 to 255.0 V (200 V Class) 0.0 to 510.0 V (400 V Class) 200.0 V (200 V Class) 400.0 V (400 V Class) - - Yes Yes Yes Set the rated current of the motor in amps.*5 *7 0.32 to 6.40 A*3 1.90 A*2 Yes Yes Yes Yes Yes 0.0 to 400.0 Hz 60.0 Hz - - Yes Yes Yes 2 to 48 poles 4 poles - - Yes Yes Yes Number of motor poles Set the number of motor poles. Number of Poles Setting Range Set the output power of the motor in kilowatts.*5 *7 Motor base frequency Set the base frequency of the T1-05 *5 *6 Rated Fre- motor in hertz. quency T1-06 Data Displays during Autotuning Open Open V/f Flux -loop -loop V/f with VecVecVecPG tor tor 1 tor 2 0.40 kW *2 Trial Operation Procedures Table 4.3 Constant Settings before Autotuning (Continued) Constant Number Name Data Displays during Autotuning Open Open V/f Flux -loop -loop V/f with VecVecVecPG tor tor 1 tor 2 Display Setting Range Factory Setting Set the base speed of the motor in min−1.*5 0 to 24000 1750 min−1 - - Yes Yes Yes 0 to 60000 600 - Yes - Yes - 0.00 to 1.89 1.20A No No Yes Yes Yes Display Motor base speed T1-07 Rated Speed Number of PG pulses when turn- Set the number of pulses for the PG (pulse generator or ing T1-08 encoder). Set the number of pulses per motor revolution PG Pulses/ without a multiplication factor. Rev Motor noload curT1-09 rent *9 * * * * * * * * * * No-Load Current Set the current value recorded in the motor’s test results for a motor without a load. Displayed only when Stationary autotuning 2 is selected (T1-01 = 4). *10 *2 1. 2. 3. 4. Not normally displayed. Displayed only when a motor switch command is set for a multi-function digital input (one of H1-01 to H1-10 set to 16). The factory setting depends on the Inverter capacity. Values are given for a 200 V Class, 0.4 kW Inverter. The setting range is from 10% to 200% of the Inverter rated output current. The value for a 200 V Class Inverter for a 0.4 kW is given. Set T1-02 and T1-04 when 2 is set for T1-01. Only set value 2 (2 or 3 for Control Boards ETC618046-S1033 and later) is possible for V/f control or V/ f control with PG. 5. For fixed output motors, set the base speed value. 6. For Inverter motors or for specialized vector motors, the voltage or frequency may be lower than for general-purpose motors. Always confirm the information on the nameplate or in test reports. If the no-load values are known, input the no-load voltage in T1-03 and the no-load current in T1-05 to ensure accuracy. 7. The settings that will ensure stable vector control are between 50% and 100% of the Inverter rating. 8. Applicable for Control Boards ETC618046-S1033 and later. Refer to Chapter 8 Procedure for Adjusting Constants after Replacement of Control Board (Page 8-3) for the details of setting 3 (Shipping adjustment). 9. Applicable for G7-Series Inverters with software versions PRG: 1039 or later. 10.The setting range depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. The upper limit depends on the setting of E2-01. Refer to page 3-15 for Digital Operator displays during autotuning. Precautions for Precision Settings Settings for autotuning are different when performing autotuning using motor test reports or design data. Use the following table as reference. Operator Display Simple Setting Precision Setting T1-03 Motor rated voltage Voltage under no-load conditions at motor rated speed T1-05 Motor base frequency Frequency under no-load conditions at rated speed 4-15 Application Settings User constants are set as required in advanced programming mode (“ADV” will be displayed on the LCD screen). All the constants that can be set in quick programming mode can also be displayed and set in advanced programming mode. Setting Examples The following are examples of settings for applications. • When using an Inverter-mounted braking resistor (ERF), set L8-01 to 1 to enable ERF braking resistor overheating protection. • To prevent the machine from being operated in reverse, set b1-04 to 1 to disable reverse operation. • To increase the speed of a 60 Hz motor by 10%, set E1-04 to 66.0 Hz. • To use a 0 to 10-V analog signal for a 60 Hz motor for variable-speed operation between 0 and 54 Hz (0% to 90% speed deduction), set H3-02 to 90.0%. • To control speed between 20% and 80% to ensure smooth gear operation and limit the maximum speed of the machine, set d2-01 to 80.0% and set d2-02 to 20.0%. No-load Operation To being no-load operation (without connecting the machine and the motor), press the LOCAL/REMOTE Key on the Digital Operator to change to LOCAL mode (the SEQ and REF indicators on the Digital Operator should be OFF). Always confirm safety around the motor and machine before starting Inverter operation from the Digital Operator. Confirm that the motor works normally and that no errors are displayed at the Inverter. Jog Frequency Reference (d1-17, default: 6.00 Hz) can be started and stopped by pressing and releasing the JOG Key on the Digital Operator. If the external sequence prevent operation from the Digital Operator, confirm that emergency stop circuits and machine safety mechanisms are functioning, and then start operation in REMOTE mode (i.e., with a signal from the control signal terminals). The safety precautions must always be taken before starting the Inverter with the motor connected to the machine. Both a Run Command (forward or reverse) and a frequency reference (or multi-step speed reference) must be provided to start Inverter operation. Input these commands and reference regardless of the operation method (i.e., LOCAL of REMOTE). INFO Loaded Operation Connect the machine to the motor and then start operation as described for no-load operation (i.e., from the Digital Operator or by using control circuit terminal signals). Connecting the Load • After confirming that the motor has stopped completely, connect the mechanical system. • Be sure to tighten all the screws when securing the motor shaft to the mechanical system. 4-16 Trial Operation Procedures Operation using the Digital Operator • Use the Digital Operator to start operation in LOCAL mode in the same way as in no-load operation. • If fault occurs during operation, make sure the STOP Key on the Digital Operator is easily accessible. • At first, set the frequency reference to a low speed of one tenth the normal operating speed. Checking Operating Status • Having checked that the operating direction is correct and that the machine is operating smoothly at slow speed, increase the frequency reference. • After changing the frequency reference or the rotation direction, check that there is no oscillation or abnor- mal sound from the motor. Check the monitor display to ensure that U1-03 (Output Current) is not too high. • Continuously driving a general-purpose motor with its rated current at a speed of less than 20 Hz may cause motor overheat. Further, if a current exceeding 70 to 80% of the load current flows for more than one minute while the motor is running at a low speed, OL1 (Motor Overload) will be generated. • When neither a braking unit (braking resistor) nor a regenerative converter is connected, some operation conditions may cause an overvoltage. Check the DC bus voltage monitor (U1-07), and adjust the acceleration/deceleration time, etc. as required. (200 V class: less than 350 V, 400 V class: less than 700 V) • Refer to Adjustment Suggestions on page 4-18 if hunting, vibration, or other problems originating in the control system occur. Check and Recording User Constants Use verify mode (“VERIFY” will be displayed on the LCD screen) to check user constants that have been changed for trial operation and record them in a user constant table. Any user constants that have been change by autotuning will also be displayed in verify mode. If required, the copy function in constants o3-01 and o3-02 displayed in advanced programming mode can be used to copy the changed settings from the Inverter to a recording area in the Digital Operator. If changed settings are saved in the Digital Operator, they can be easily copied back to the Inverter to speed up system recovery if for any reason the Inverter has to be replaced. The following functions can also be used to manage user constants. • Recording user constants • Setting access levels for user constants • Setting a password Recording User Constants (o2-03) If o2-03 is set to 1 after completing trial operation, the settings of user constants will be saved in a separate memory area in the Inverter. Later, after Inverter settings have been changed, the user constants can be initialized to the settings saved in the separate memory area when o2-03 was set to 1 by setting A1-03 (Initialize) to 1110. User Constant Access Levels (A1-01) A1-01 can be set to 0 (monitoring-only) to prevent user constants from being changed. A1-01 can also be set to 1 (User-specified Constants) and used along with A2 constants to display only constants required by the machine or application in a programming mode. Password (A1-04 and A1-05) When the access level is set to monitoring-only (A1-01 = 0), a password can be set so that user constants will be displayed only when the correct password is input. 4-17 Adjustment Suggestions If hunting, vibration, or other problems originating in the control system occur during trial operation, adjust the constants listed in the following table according to the control method. This table lists only the most commonly used user constants. Table 4.4 Adjusted User Constants Control Method V/f control (A1-02 = 0 or 1) Name (Constant Number) Performance Factory Setting 0.50 to 2.00 • Reduce the setting if torque is insufficient for heavy loads. • Increase the setting if hunting or vibration occurs for light loads. 0 to default • Increase the setting if motor magnetic noise is high. • Reduce the setting if hunting or vibration occurs at low to middle-range speeds. 200 to 1000 ms • Reduce the setting if torque or speed response is slow. • Increase the setting if hunting or vibration occurs. Hunting-prevention gain (N1-02) Carrier frequency selection (C6-02) • Reducing motor magnetic noise • Controlling hunting and vibration at low speeds Depends on capacity Torque compensation primary delay time constant (C4-02) • Increasing torque and speed response • Controlling hunting and vibration Depends on capacity Torque compensation gain (C4-01) • Improving torque at low speeds (10 Hz or lower) • Controlling hunting and vibration 1.00 0.50 to 1.50 • Increase the setting if torque is insufficient at low speeds. • Reduce the setting if hunting or vibration occurs for light loads. Middle output frequency voltage (E1-08) Minimum output frequency voltage (E1-10) • Improving torque at low speeds • Controlling shock at startup Depends on capacity and voltage Default to Default + 3 to 5 V* • Increase the setting if torque is insufficient at low speeds. • Reduce the setting if shock at startup is large. 0.50 to 2.00 • Reduce the setting if torque or speed response is slow. • Increase the setting if hunting or vibration occurs. 20 to 100 ms • Reduce the setting if torque or speed response is slow. • Increase the setting if hunting or vibration occurs. 100 to 500 ms • Reduce the setting if speed response is slow. • Increase the setting if the speed is not stable. 0.5 to 1.5 • Increase the setting if speed response is slow. • Reduce the setting if the speed is too fast. Torque compensation primary delay time constant (C4-02) • Increasing torque and speed response • Controlling hunting and vibration 20 ms • Increasing speed Slip compensation priresponse mary delay time (C3200 ms • Improving speed sta02) bility Slip compensation gain (C3-01) 4-18 Adjustment Method Controlling hunting and vibration in mid1.00 dle-range speeds (10 to 40 Hz) • Increasing torque Speed feedback detecand speed response tion control (AFR) • Controlling hunting 1.00 gain and vibration in mid(N2-01) dle-range speeds (10 to 40 Hz) Open-loop vector 1 control (A1-02 = 2) Recommended Setting • Improving speed accuracy 1.0 Adjustment Suggestions Table 4.4 Adjusted User Constants (Continued) Control Method Name (Constant Number) Carrier frequency selection (C6-02) Open-loop vector 1 control Middle output fre(A1-02 = 2) quency voltage (E1-08) Minimum output frequency voltage (E1-10) Performance Recommended Setting Adjustment Method • Reducing motor magnetic noise • Controlling hunting and vibration at low speeds (10 Hz or less) Depends on capacity 0 to default • Increase the setting if motor magnetic noise is high. • Reduce the setting if hunting or vibration occurs at low speeds. • Improving torque at low speeds • Controlling shock at startup Depends on capacity and voltage Default to Default + 1 or 2 V* • Increase the setting if torque or speed response is slow. • Reduce the setting if shock at startup is large. 10.00 to 50.00 • Increase the setting if torque or speed response is slow. • Reduce the setting if hunting or vibration occurs. 0.300 to 1.000 s • Reduce the setting if torque or speed response is slow. • Increase the setting if hunting or vibration occurs. ASR proportional gain • Torque and speed 1 (C5-01) and response ASR proportional gain • Controlling hunting 2 (C5-03) and vibration ASR integral time 1 (high-speed) (C5-02) and ASR integral time 2 (low-speed) (C5-04) Factory Setting • Torque and speed response • Controlling hunting and vibration 20.00 0.500 s Flux vector ASR switching frecontrol quency (C5-07) (A1-02 = 3) Switching the ASR proportional gain and integral time according to the output frequency 0.0 Hz 0.0 to max. output frequency Set the output frequency at which to change the ASR proportional gain and integral time when the same values cannot be used for both high-speed and low-speed operation. ASR primary delay time (C5-06) • Controlling hunting and vibration 0.004 s 0.004 to 0.020 s Increase the setting if machine rigidity is low and the system vibrates easily. Carrier frequency selection (C6-02) • Reducing motor Depends magnetic noise • Controlling hunting on the and vibration at low capacity. speeds (3 Hz or less) 2.0 kHz to default • Increase the setting if motor magnetic noise is high. • Reduce the setting if hunting or vibration occurs at low to middle-range speeds. 10.00 to 50.00 • Increase the setting if torque or speed response is slow. (Refer to Procedure for Increasing the Speed Response below.) • Reduce the setting if hunting or vibration occurs. 0.300 to 1.000 s • Reduce the setting if torque or speed response is slow. • Increase the setting if hunting or vibration occurs. Open-loop vector 2 control (A1-02 = 4) ASR proportional gain • Torque and speed 1 (C5-01) and response ASR proportional gain • Controlling hunting and vibration 2 (C5-03) ASR integral time 1 (high-speed) (C5-02) and ASR integral time 2 (low-speed) (C5-04) • Torque and speed response • Controlling hunting and vibration 10.00 0.500 s 4-19 Table 4.4 Adjusted User Constants (Continued) Control Method Name (Constant Number) ASR switching frequency (C5-07) ASR primary delay time (C5-06) ASR primary delay time 2 (C5-10) Open-loop vector 2 control (A1-02 = 4) Integral time of speed estimator (N4-07) Performance Switching the ASR proportional gain and integral time according to the output frequency Factory Setting 0.0 Hz 0.0 to max. output frequency 0.010 s 0.04 to 0.020 s 0.035 s 0.010 to 0.035 s 0.010 s 0.010 to 0.035 s • Controlling hunting and vibration • Controlling hunting and vibration • Speed response • Controlling hunting and vibration 0.030 ms High-speed proportional gain of speed estimator (N4-10) • Speed response • Controlling hunting and vibration Carrier frequency selection (C6-11) • Reducing motor magnetic noise Depends • Controlling hunting on the and vibration at low capacity. speeds (3 Hz or less) 15 * The setting is given for 200 V Class Inverters. Double the voltage for 400 V Class Inverters. 4-20 Recommended Setting Adjustment Method Set the output frequency at which to change the ASR proportional gain and integral time when the same values cannot be used for both high-speed and low-speed operation. Increase the setting if machine rigidity is low and the system vibrates easily. (Enabled in the range 0 to 35 Hz. Refer to Procedure for Increasing the Speed Response below.) Increase the setting if machine rigidity is low and the system vibrates easily. (Enabled above 35 Hz. Refer to Procedure for Increasing the Speed Response below.) 0.015 to 0.060 ms (Enabled below the N4-11 setting.) • Reduce the setting if speed response is slow. (Typically, reduce in intervals of 0.05. Refer to Procedure for Increasing the Speed Response below.) • Increase the setting if hunting or vibration occurs. 10 to 60 (Enabled below the N4-11 setting.) • Increase the setting if speed response is slow. (Typically, increase in intervals of 5. Refer to Procedure for Increasing the Speed Response below.) • Reduce the setting if hunting or vibration occurs. Default value • Increase the setting if motor magnetic noise is high. • Reduce the setting if hunting or vibration occurs at low to middle-range speeds. Adjustment Suggestions Procedure for Increasing the Speed Response (PRG: 102 only) Increase the speed response. C5-01 ≥ 30.0 No Increase the setting for the ASR proportional gain (C5-01). (Typically, increase in intervals of 5.) Yes C5-06 ≤ 0.01 No Reduce the setting for the ASR primary delay time (C5-06). (Typically, reduce in intervals of 0.01.) Yes Speed ≥ N4-11 Is the speed response to be increased for low-speed operation or high-speed operation? Increase the setting for the high-speed proportional gain of speed estimator (N4-10). (Typically, increase in intervals of 5.) Speed < N4-11 Reduce the setting for the integral time of speed estimator (N4-07). (Typically, reduce in intervals of 0.005.) • Do not change the Torque Compensation Gain (C4-01) from its default setting of 1.00 when using open- loop vector 1 control. • If speeds are inaccurate during regeneration in open-loop vector 1 control, enable Slip Compensation Dur- ing Regeneration (C3-04 = 1). • Use slip compensation to improve speed control during V/f control (A1-02 = 0). Set the Motor Rated Current (E2-01), Motor Rated Slip (E2-02), and Motor No-load Current (E2-03), and then adjust the Slip Compensation Gain (C3-01) to between 0.5 and 1.5. The default setting for V/f control is C3-01 = 0.0 (slip compensation disabled). • To improve speed response and stability in V/f control with a PG (A1-02 = 1), set the ASR constants (C5- 01 to C5-05) to between 0.5 and 1.5 times the default. (It is not normally necessary to adjust this setting.) ASR for V/f control with a PG will only control the output frequency; a high gain, such as is possible for open-loop vector 2 control or flux vector control, cannot be set. The following user constants will also indirectly affect the control system. Table 4.5 Constants Indirectly Affecting Control and Applications Name (Constant Number) Application Dwell function (b6-01 to b6-04) Used for heavy loads or large machine backlashes. Droop function (b7-01 to b7-02) Used to soften the torque or to balance the load between two motors. Can be used when the control method (A1-02) is set to 3 or 4. Acceleration/deceleration times (C1-01 to C1-11) Adjust torque during acceleration and deceleration. S-curve characteristics (C2-01 to C2-04) Used to prevent shock when completing acceleration. Jump frequencies (d3-01 to d3-04) Used to avoid resonance points during operation. Analog input filter time constant (H3-12) Used to prevent fluctuations in analog input signals caused by noise. Stall prevention (L3-01 to L3-06, L3-11, L3-12) Used to prevent overvoltage errors and motor stalling for heavy loads or rapid acceleration/deceleration. Stall prevention is enabled by default and the setting does not normally need to be changed. When using a braking resistor, however, disable stall prevention during deceleration by setting L3-04 to 0. 4-21 Table 4.5 Constants Indirectly Affecting Control and Applications (Continued) Name (Constant Number) Application Set the maximum torque during vector control. If a setting is increased, Torque limits (L7-01 to L7-04, L7-06, L7-07) use a motor with higher capacity than the Inverter. If a setting is reduced, stalling can occur under heavy loads. Feed forward control (N5-01 to N5-03) 4-22 Used to increase response for acceleration/deceleration or to reduce overshooting when there is low machine rigidity and the gain of the speed controller (ASR) cannot be increased. The inertia ratio between the load and motor and the acceleration time of the motor running alone must be set. 5 User Constants This chapter describes all user constants that can be set in the Inverter. User Constant Descriptions .........................................5-2 Digital Operation Display Functions and Levels ..........5-3 User Constant Tables ..................................................5-8 User Constant Descriptions This section describes the contents of the user constant tables. Description of User Constant Tables User constant tables are structured as shown below. Here, b1-01 (Frequency Reference Selection) is used as an example. Name Constant Number Display Reference selection b1-01 Reference Source Setting Range Description Set the frequency reference input method. 0: Digital Operator 1: Control circuit terminal (analog input) 2: MEMOBUS communications 3: Option board 4: Pulse train input 0 to 4 Change Factory during Setting Operation 1 No Control Methods V/f V/f with PG Open -loop Vector 1 Flux Vector Q Q Q Q Open MEMOBUS Loop Page Vec- Register tor 2 Q 180H - • Constant Number: The number of the user constant. • Name: The name of the user constant. • Description: Details on the function or settings of the user constant. • Setting Range: The setting range for the user constant. • Factory Setting: The factory setting (each control method has its own factory setting. Therefore the factory setting changes when the control method is changed.) Refer to page 5-87 for factory settings by control method. • Change during Operation: Indicates whether or not the constant can be changed while the Inverter is in operation. Yes: Changes possible during operation. No: • Control Methods: 5-2 Changes not possible during operation. Indicates the control methods in which the user constant can be monitored or set. Q: Items which can be monitored and set in either quick programming mode or advanced programming mode. A: Items which can be monitored and set only in advanced programming mode. No: Items which cannot be monitored or set for the control method. • MEMOBUS Register: The register number used for MEMOBUS communications. • Page: Reference page for more detailed information on the constant. Digital Operation Display Functions and Levels Digital Operation Display Functions and Levels The following figure shows the Digital Operator display hierarchy for the Inverter. MENU Drive Mode Inverter can be operated and its status can be displayed. Quick Programming Mode Minimum constants required for operation can be monitored or set. Advanced Programming Mode All constants can be monitored or set. Verify Mode Constants changed from the default settings can be monitored or set. Autotuning Mode Automatically sets motor constants if autotuning data (from motor nameplate) is input for open-loop vector control or to measure the line-to-line resistance for V/f control. No. Function Display Page U1 U2 Status Monitor Constants Monitor 5-78 Fault Trace Fault Trace U3 5-84 Fault History Fault History 5-86 5-8 A1 Initialize Mode Initialization A2 User-specified Setting Mode User Parameter 5-9 b1 Operation Mode Selections Sequence 5-10 b2 DC Injection Braking DC Braking 5-12 b3 Speed Search Speed Search 5-13 b4 Timer Function Delay Timers 5-15 b5 PID Control PID Control 5-15 b6 Dwell Functions 5-17 b7 Droop Control b8 Energy Saving Reference Hold Droop Control Energy Saving b9 Zero-servo Zero Servo 5-20 C1 Acceleration/Deceleration Accel/Decel 5-21 C2 S-curve Acceleration/Deceleration 5-22 C3 Motor Slip Compensation C4 Torque Compensation S-Curve Acc/Dcc Motor-Slip Comp Torque Comp C5 Speed Control (ASR) ASR Tuning 5-25 C6 Carrier Frequency Carrier Freq 5-26 d1 Preset Reference 5-27 d2 Reference Limits d3 Jump Frequencies Preset Reference Reference Limits Jump Frequencies d4 Reference Frequency Hold Sequence 5-29 d5 Torque Control Torque Control 5-30 d6 Field Weakening Fieldweakening 5-31 E1 V/f Pattern V/f Pattern 5-33 E2 Motor Setup Motor Setup 5-34 E3 Motor 2 V/f Pattern V/f Pattern 2 5-36 E4 Motor 2 Setup 5-38 F1 PG Option Setup Motor Setup 2 PG Option Setup F2 Analog Reference Board AI-14 Setup 5-41 F3 Digital Reference Board 5-42 F4 Analog Monitor Boards F5 Digital Output Boards F6 Communications Option Boards DI-08, 16 Setup AO-08, 12 Setup DO-02,08 Setup ComOPT Setup H1 Multi-function Contact Inputs Digital Inputs 5-46 H2 Multi-function Contact Outputs Digital Outputs 5-49 H3 Analog Inputs Analog Inputs 5-51 H4 Multi-function Analog Outputs 5-54 H5 MEMOBUS Communications H6 Pulse Train L1 Motor Overload L2 Power Loss Ridethrough L3 Stall Prevention L4 Reference Detection Analog Outputs Serial Com Setup Pulse I/O Setup Motor Overload PwrLoss Ridethru Stall Prevention Ref Detection L5 Fault Restart Fault Restart 5-63 L6 Torque Detection Torque Detection 5-64 L7 Torque Limits Torque Limit 5-65 L8 Hardware Protection Hdwe Protection 5-66 N1 Hunting Prevention Function Hunting Prev 5-69 N2 Speed Feedback Protection Control AFR 5-70 N3 High-slip Braking High Slip 5-70 N4 Speed Estimation Observer 5-71 N5 Feed Forward 5-73 o1 Monitor Select o2 Multi-function Selections o3 Copy Function Feedfoward Cont Monitor Select Key Selections COPY Function T Motor Autotuning Auto-Tuning 5-77 5-18 5-19 5-23 5-24 5-28 5-29 5-39 5-43 5-44 5-45 5-55 5-57 5-58 5-59 5-61 5-62 5-73 5-75 5-76 5-3 User Constants Settable in Quick Programming Mode The minimum user constants required for Inverter operation can be monitored and set in quick programming mode. The user constants displayed in quick programming mode are listed in the following table. These, and all other user constants, are also displayed in advanced programming mode. Refer to the overview of modes on page 3-5 for an overview of quick programming mode. Name Constant Number A1-02 Display Control method selection Control Method Reference selection b1-01 b1-02 Reference Source Operation method selection Run Source Stopping method selection b1-03 Stopping Method C1-01 C1-02 C6-02 Description Setting Range Factory Setting Set the control method for the Inverter. 0: V/f control 1: V/f control with PG 2: Open-loop vector 1 control 3: Flux vector control 4: Open-loop vector 2 control 0 to 4 2 Set the frequency reference input method. 0: Digital Operator 1: Control circuit terminal (analog input) 2: MEMOBUS communications 3: Option board 4: Pulse train input 0 to 4 Set the Run Command input method 0: Digital Operator 1: Control circuit terminal (sequence input) 2: MEMOBUS communications 3: Option board 0 to 3 Select stopping method when Stop Command is sent. 0: Deceleration to stop 1: Coast to stop 2: DC braking stop (Stops faster than coast to stop, without regenerative operation.) 3: Coast to stop with timer (Run Commands are disregarded during deceleration time.) Acceleration time 1 Set the acceleration time in seconds for the output frequency to climb from Accel 0% to 100%. Time 1 Deceleration time 1 Set the deceleration time in seconds for the output frequency to fall from Decel 100% to 0%. Time 1 Carrier frequency Select carrier wave fixed pattern. selection Select F to enable detailed settings using constants C6-03 to C6-07. Carrier Freq Sel 5-4 Control Methods Change during Operation 0 to 3 *10 0.0 to 6000.0 Open MEMOBUS Loop Vec- Register tor 2 V/f V/f with PG Open -loop Vector 1 Flux Vector No Q Q Q Q Q 102H 1 No Q Q Q Q Q 180H 1 No Q Q Q Q Q 181H 0 No Q Q Q Q Q 182H Yes Q Q Q Q Q 200H Yes Q Q Q Q Q 201H No Q Q Q Q 10.0 s *1 1 to F 6 *11 *2 No *13 224H Digital Operation Display Functions and Levels Name Constant Number Display Control Methods Description Setting Range Factory Setting C6-11 Carrier frequency for Select carrier frequency when openopen-loop loop vector 2 control is used. 1: 2kHz vector 2 2: 4kHz control 3: 6kHz Carrier 4: 8kHz Freq Sel d1-01 Frequency Set the frequency reference in the unit reference 1 specified in o1-03 (Frequency Units Reference for Reference Setting And Monitor, default: Hz) 1 0.00 Hz d1-02 Frequency reference 2 Frequency reference when multi-step speed reference 1 is ON for a multiReference function input (unit: Set in o1-03). 2 d1-03 d1-04 d1-17 E1-03 V/f V/f with PG Open -loop Vector 1 Flux Vector No No No No *13 *13 *13 Yes Q Q Q 0.00 Hz Yes Q Q Frequency reference 3 Frequency reference when multi-step speed reference 2 is ON for a multiReference function input (unit: Set in o1-03). 3 0 to 0.00 Hz 400.00 Yes Q Frequency Frequency reference when multi-step reference 4 speed reference 1 and 2 are ON for a Reference multi-function input (unit: Set in o103). 4 0.00 Hz Yes 6.00 Hz Jog frequency reference Jog Reference E1-01 Change during Operation Set the Inverter input voltage in 1 volt. This set value will be the basis for the Input Volt- protection functions. age V/F Selection 0 to E: Select from 15 preset patterns. F: Custom user-set patterns (Applicable for setting E1-04 to E1-10). 4 *2 No Q 22DH Q Q 280H Q Q Q 281H Q Q Q Q 282H Q Q Q Q Q 283H Yes Q Q Q Q Q 292H No Q Q Q Q Q 300H No Q Q No No No 302H *13 *7 Frequency reference when Jog Frequency Selection, FJOG command, or RJOG command is ON for a multifunction input (unit: Set in o1-03). Input voltage setting V/f pattern selection 1 to 4 Open MEMOBUS Loop Vec- Register tor 2 155 to 255 *3 0 to F 200 V *3 F 5-5 Name Constant Number E1-04 Control Methods Setting Range Description Display Max. output frequency (FMAX) 40.0 to 60.0 Hz 400.0 *4 E1-05 Max Voltage E1-06 Base frequency (FA) Output voltage (V) VMAX (E1-05) VBASE (E1-13) Frequency (Hz) VMIN (E1-10) FMIN (E1-09) FA FMAX (E1-06) (E1-04) Base Frequency E1-09 Min. output frequency (FMIN) E1-13 Base Voltage E2-01 E2-04 0.0 to 255.0 200.0 V *3 *3*4 0.0 to 400.0 60.0 Hz *7 0.0 to 400.0 *7 Min Frequency Base voltage (VBASE) Open MEMOBUS Loop Vec- Register tor 2 V/f V/f with PG Open -loop Vector 1 Flux Vector No Q Q Q Q Q 303H No Q Q Q Q Q 304H No Q Q Q Q Q 305H No Q Q Q A Q 308H No A A Q Q Q 30CH No Q Q Q Q Q 30EH No No Q No Q Q 311H No Q Q Q Q Q 318H *7 Max Frequency Max. voltage (VMAX) Factory Setting Change during Operation Change this setting only when making advanced adjustments for V/f in the fixed outputs area. Normally, there is no need to make these settings. Motor rated current Set the motor rated current in amps. This set value becomes the base value for motor protection, torque limit, and torque control. It is set automatically Motor Rated FLA when using autotuning. Number of motor Set the number of motor poles. The poles value is set automatically during autoNumber of tuning. 0.0 to 255.0 *3 0.32 to 6.40 *6 *4 0.5 Hz *4 0.0 V *5 1.90 A *2 2 to 48 4 poles 0.00 to 650.00 0.40 Poles E2-11 Motor rated output Mtr Rated Power F1-01 PG constant Set the number of pulses per rotation for the PG (pulse generator or PG Pulses/ encoder) being used. (Do not set as a multiple.) Rev Gain (terminal FM) H4-02 Set the output of the motor in units of 0.01kW. This constant is automatically set during autotuning. Terminal FM Gain Set the voltage level gain for multifunction analog output 1. Set the number of multiples of 10 V to be output as the 100% output for the monitor items. Voltage output from the terminals, however, have a 10 V max. meter calibration function.*13 5-6 *8 0 to 60000 600 No No Q No Q No 380H 0.00 to 2.50 1.00 Yes Q Q Q Q Q 41EH Digital Operation Display Functions and Levels Name Constant Number H4-05 Control Methods Description Display Gain (ter- Set the voltage level gain for multiminal AM) function analog output 2. Set the number of multiples of 10 V to be output as the 100% output for the monitor items. Voltage output from the Terminal terminals, however, have a 10 V max. AM Gain A meter calibration function is avail- Setting Range Factory Setting Change during Operation 0.00 to 2.50 0.50 0 to 3 Open MEMOBUS Loop Vec- Register tor 2 V/f V/f with PG Open -loop Vector 1 Flux Vector Yes Q Q Q Q Q 421H 1 No Q Q Q Q Q 480H 1 No Q Q Q Q Q 492H able.*13 L1-01 Motor pro- Set to enable or disable the motor tection overload protection function using the selection electronic thermal relay. 0: Disabled 1: General-purpose motor protection 2: Inverter motor protection 3: Vector motor protection In some applications when the Inverter power supply is turned off, MOL Fault the thermal value is reset, so even if Select this constant is set to 1, protection may not be effective. When several motors are connected to one Inverter, set to 0 and ensure that each motor is installed with a protection device. Stall prevention selection during deceleration L3-04 StallP Decel Sel 0: Disabled (Deceleration as set. If deceleration time is too short, a main circuit overvoltage may result.) 1: Enabled (Deceleration is stopped when the main circuit voltage exceeds the overvoltage level. Deceleration restarts when voltage is returned.) 2: Intelligent deceleration mode (Deceleration rate is automatically adjusted so that the Inverter can decelerate in the shortest possible time. Set deceleration time is disregarded.) 3: Enabled (with Braking Resistor Unit) When a braking option (Braking Resistor, Braking Resistor Unit, Braking Unit) is used, always set to 0 or 3. 0 to 3 *9 * 1. The setting range for acceleration/deceleration times depends on the setting of C1-10 (Acceleration/deceleration Time Setting Unit). If C1-10 is set to 0, the setting range is 0.00 to 600.00 (s). * 2. The factory settings depend on the Inverter capacity. The values for a 200 V Class Inverter for 0.4 kW are given. * 3. These are values for a 200 V Class Inverter. Values for a 400 V Class Inverter are double. * 4. The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given. * 5. E1-13 is set to the same value as E1-05 by autotuning. * 6. The setting range is from 10% to 200% of the Inverter rated output current. The value for a 200 V Class Inverter for 0.4 kW is given. For the motor no-load current, set E2-03 to a value less than that of E2-01. * 7. The setting range for open-loop vector 2 control is 0 to 66.0 (0 to 132.0 for PRG: 103). * 8. The same capacity as that of the Inverter will be set if the constants are initialized. * 9. The setting range for flux vector and open-loop vector 2 control is 0 to 2. * 10.0 or 1 for flux vector control and open-loop vector 2 control. * 11.The setting range depends on the capacity of the Inverter. The values for a 200 V Class Inverter for 0.4 kW are given. * 12.Displayed in Quick Programming Mode when motor 2 is set for a multi-function input. * 13.The CH1 output can be adjusted when the H4-02 or H4-03 setting is displayed in Quick, Advanced, or Verify mode while the motor is stopped. The CH2 output can be adjusted when the H4-05 or H4-06 setting is displayed in quick, Advance, or Verify mode while the motor is stopped. For analog output, the value equivalent to 100% of output value of monitored item is multiplied by the gain setting and the set bias is added. 5-7 User Constant Tables A: Setup Settings The following settings are made with the environment constants (A constants): Language displayed on the Digital Operator, access level, control method, initialization of constants. Initialize Mode: A1 User constants for the environment modes are shown in the following table. Name Constant Number Display Language selection for Digital Operator display A1-00 Select Language Constant access level A1-01 Access Level Control method selection A1-02 Control Method 5-8 Change Factory during Setting Operation Control Methods Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector Yes A A A A A 100H - 2 Yes A A A A A 101H 4-17 6-156 2 No Q Q Q Q Q 102H 4-5 4-7 4-18 Description Setting Range Used to select the language displayed on the Digital Operator (LCD). 0: English 1: Japanese 2: German 3: French 4: Italian 5: Spanish 6: Portuguese This constant is not initialized by the initialize operation. 0 to 6 1 Used to set the constant access level (set/read.) 0: Monitoring only (Monitoring drive mode and setting A1-01 and A104.) 1: Used to select user constant (Only constants set in A201 to A2-32 can be read and set.) 2: Advanced (Constants can be read and set in both quick programming mode and advanced programming (A) mode.) 0 to 2 Used to select the control method for the Inverter 0: V/f control 1: V/f with PG feedback 2: Open-loop vector 1 control 3: Flux vector 4: Open-loop vector 2 control This constant is not initialized by the initialize operation. 0 to 4 User Constant Tables Name Constant Number Display Initialize A1-03 Init Parameters Password A1-04 Enter Password Password setting A1-05 Select Password Change Factory during Setting Operation Control Methods Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 103H 6-11 6-150 0 No A A A A A 104H 4-17 6-157 0 No A A A A A 105H 4-17 6-157 Description Setting Range Used to initialize the constants using the specified method. 0: No initializing 1110: Initializes using the User constants 2220: Initializes using a two-wire sequence. (Initializes to the factory setting.) 3330: Initializes using a three-wire sequence. 0 to 3330 0 Password input when a password has been set in A1-05. This function write-protects some constants of the initialize mode. If the password is changed, A1-01 to A1-03 and A2-01 to A2-32 constants can no longer be changed. (Programming mode constants can be changed.) 0 to 9999 Used to set a four digit number as the password. This constant is not usually displayed. When the Password (A1-04) is displayed, hold down the RESET Key and press the Menu Key and the password will be displayed. 0 to 9999 User-set Constants: A2 The constants set by the user are listed in the following table. Name Constant Number Display Control Methods Description Factory Setting b1-01 to o3-02 - No V/f V/f with PG Open Loop Vector 1 Flux Vector A A A A Open MEMOBUS Loop Page Vec- Register tor 2 User setting constants A2-01 to A2-32 Used to set the constant numbers that can be set/read. Maximum 32. Effective when the Constant Access Level (A1-01) is set to User Param 1 User Program (1). Constants to 32 set in constants A2-01 to A232 can be set/read in programming mode. Setting Range Change during Operation A 106H to 125H 6-157 5-9 b: Application Constants The following settings are made with the application constants (B constants): Operation method selection, DC injection braking, speed searching, timer functions, dwell functions, droop control, energy saving control, and zero-servo control. Operation Mode Selections: b1 User constants for operation mode selection are shown in the following table. Name Constant Number Display Reference selection b1-01 Reference Source Operation method selection b1-02 Run Source Stopping method selection b1-03 Stopping Method b1-04 Prohibition of reverse operation Reverse Oper 5-10 Description Set the frequency reference input method. 0: Digital Operator 1: Control circuit terminal (analog input) 2: MEMOBUS communications 3: Option board 4: Pulse train input Setting Range 0 to 4 Change Factory during Setting Operation 1 No Control Methods V/f Q V/f with PG Q Open Loop Vector 1 Q Flux Vector Q Open MEMOBUS Loop Page Vec- Register tor 2 Q 180H 4-5 6-2 6-76 6-94 Set the Run Command input method. 0: Digital Operator 1: Control circuit terminal (sequence input) 2: MEMOBUS communications 3: Option board 0 to 3 1 No Q Q Q Q Q 181H 4-5 6-10 6-76 6-94 Used to set the stopping method used when a Stop Command is input. 0: Deceleration to stop 1: Coast to stop 2: DC injection braking stop (Stops faster than coast to stop, no regenerative operation.) 3: Coast to stop with timer (Run Commands are disregarded during deceleration.) 0 to 3 * 0 No Q Q Q Q Q 182H 4-6 6-12 0 or 1 0 No A A A A A 183H 6-62 0: Reverse enabled 1: Reverse disabled User Constant Tables Name Constant Number Display Operation selection for setting E1-09 or less b1-05 Zero-Speed Oper Read sequence input twice b1-06 Cntl Input Scans Operation selection after switching to remote mode b1-07 LOC/REM RUN Sel b1-08 Change Factory during Setting Operation Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No No No No A No 184H 6-12 1 No A A A A A 185H - 0 or 1 0 No A A A A A 186H - 0 to 2 0 No A A A A A 187H - 0 or 1 0 No No No No No A 1DEH - Description Setting Range Used to set the method of operation when the frequency reference input is less than the minimum output frequency (E1-09). 0: Run at frequency reference (E1-09 not effective). 1: STOP (Frequencies below E1-09 in the coast to stop state.) 2: Run at min. frequency. (E1-09) 3: Run at zero-speed (Frequencies below E1-09 are zero) 0 to 3 0 Used to set the responsiveness of the control inputs (forward/ reverse and multi-function inputs.) 0: One scan every 5 ms (Use for fast responses.) 1: Two scans every 5 ms (Use for possible malfunction due to noise.) 0 or 1 Used to set the operation mode by switching to the Remote mode using the Local/Remote Key. 0: Run signals that are input during mode switching are disregarded. (Input Run signals after switching the mode.) 1: Run signals become effective immediately after switching to the Remote mode. Run Com- Used to set an operation intermand selec- lock in programming modes. tion in 0: Cannot operate. program1: Can operate (Disabled ming modes when Digital Operator is set to select Run Command (when b1-02 = 0)). RUN CMD 2: Cannot operate. (Cannot be at PRG in programming mode Control Methods during operation.)*2 b1-10 Mode selec- Enable for machines that tion for rotate the motor only in the zero-speed same direction as the speed reference. This setting improves the control stability ModeSel of the motor at zero-speed. @ZeroSpd 0: Disabled 1: Enabled * 1. 0 or 1 for flux vector control and open-loop vector 2 control. * 2. Applicable for G7 series Inverters with software versions PRG: 1039 or later. 5-11 DC Injection Braking: b2 User constants for injection braking are shown in the following table. Name Constant Number b2-01 Display Zero-speed level (DC injection braking starting frequency) DCInj Start Freq b2-02 DC injection braking current DCInj Current DC injection braking time at start b2-03 DCInj Time@Start DC injection braking time at stop b2-04 DCInj Time@Stop b2-08 5-12 Control Methods Description Setting Range Factory Setting Change during Operation Used to set the frequency which starts DC injection braking in units of Hz when deceleration to stop is selected. When b2-01 is less than E109, E1-09 becomes the DC injection braking starting frequency. 0.0 to 10.0 0.5 Hz Sets the DC injection braking current as a percentage of the Inverter rated current. 0 to 100 Used to set the time to perform DC injection braking at start in units of 1 second. Used to stop coasting motor and restart it. When the set value is 0, DC injection braking at start is not performed. Used to set the time to perform DC injection braking at stop in units of 1 second. Used to prevent coasting after the Stop Command is input. When the set value is 0.00, DC injection braking at stop is not performed. Magnetic flux Sets the magnetic flux comcompensapensation as a percentage of tion volume the no-load current. Field Comp Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 189H 6-12 6-145 50% No A A A No No 18AH 6-12 6-16 0.00 to 10.00 0.00 s No A A A A A 18BH 6-13 6-16 0.00 to 10.00 0.50 s No A A A A A 18CH 6-13 0 to 1000 0% No No No A No No 190H - User Constant Tables Speed Search: b3 User constants for the speed search are shown in the following table. Name Constant Number Display Speed search selection (current detection or speed calculation) b3-01 SpdSrch at Start Control Methods Setting Range Factory Setting Change during Operation 0 to 3 2*1 Sets the speed search operation current as a percentage, taking the Inverter rated current as 100%. Not usually necessary to set. When restarting is not possible with the factory settings, reduce the value. 0 to 200 Sets the output frequency deceleration time during speed search in 1-second units. Set the time for deceleration from the maximum output frequency to the minimum output frequency. Sets the magnetic contactor operating delay time when there is a magnetic contactor on the output side of the Inverter. When a speed search is performed after recovering from a momentary power loss, the search operation is delayed by the time set here. Description Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A No A 191H 6-65 100%*1 No A No A No A 192H 6-65 0.1 to 10.0 2.0 s No A No A No No 193H 6-65 0.0 to 20.0 0.2 s No A A A A A 195H 6-65 Enables/disables the speed search function for the Run Command and sets the speed search method. 0: Disabled, speed calculation 1: Enabled, speed calculation 2: Disabled, current detection 3: Enabled, current detection Speed Calculation: When the search is started, the motor speed is calculated and acceleration/deceleration is performed from the calculated speed to the specified frequency (motor direction is also searched). Current Detection: The speed search is started from the frequency when power was momentarily lost and the maximum frequency, and the speed is detected at the search current level. b3-02 Speed search operating current (current detection) SpdSrch Current b3-03 Speed search deceleration time (current detection) SpdSrch Dec Time b3-05 Speed search wait time (current detection or speed calculation) Search Delay 5-13 Name Constant Number b3-10 *2 *2 b3-19 *2 Operation restarts at a speed obtained by multiplying the speed from the speed search by the compensation gain (excitation search only.) Increase this setting if overvoltages occur when a speed search is performed after a long baseblock, for example, in searches at startup. 1.00 to 1.20 1.10 Sets the proportional gain (PI control) of the speed estimator during speed search taking the setting of N4-08 as equivalent to a setting of 1.0. Usually, there is no need to change this setting. If, however, the load inertia is large and overvoltages occur during the search, reduce this setting. Increase this setting for greater speed coincidence response. 0.1 to 2.0 0: Disabled (operates with specified rotation direction) 1: Enabled (operates with rotation direction found by search) No A No A No A 19AH 6-65 1.0% No No No No No A 19DH 6-66 0 or 1 1 No A A A No A 19EH 6-66 0 to 200 150% No A No A No A 1F0H 6-66 Speed search retrial detec- Sets the time for detection in a speed search retrial in units of tion time seconds. SrchRestart Time 0.00 to 1.00 0.10 s No A No A No A 1F1H 6-66 Number of speed search Sets the number of times that a retrials speed search can be retried. Num of SrchRestr 0 to 10 0 No A No A No A 1F2H 6-66 Speed search detection compensation gain (speed calculation) Proportional gain of the speed estimator during speed search Rotation direction search selection Speed search retrial current level Sets the current level to retry a speed search as a percentage, taking the Inverter rated current as 100%. * 1. The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given. * 2. Applicable for G7-Series Inverters with software versions PRG: 1039 or later. 5-14 Open MEMOBUS Loop Page Vec- Register tor 2 V/f Display SrchRestart Lv1 b3-18 Factory Setting Flux Vector Bidir Search Sel b3-17 Setting Range Open Loop Vector 1 Srch Est P Gain b3-14 Description V/f with PG Srch Detect Comp b3-13 Control Methods Change during Operation User Constant Tables Timer Function: b4 User constants for timer functions are shown in the following table. Name Constant Number Display Timer function ONdelay time b4-01 Delay-ON Timer Timer function OFFdelay time b4-02 Delay-OFF Timer Control Methods Setting Range Factory Setting Change during Operation Sets the timer function output ON-delay time (dead band) for the timer function input, in 1-second units. Enabled when a timer function is set in H1- or H2. 0.0 to 300.0 0.0 s Sets the timer function output OFF-delay time (dead band) for the timer function input, in 1-second units. Enabled when a timer function is set in H1- or H2. 0.0 to 300.0 0.0 s Description Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 1A3H 6-105 No A A A A A 1A4H 6-105 PID Control: b5 User constants for PID control are shown in the following table. Name Constant Number Display PID control method selection b5-01 PID Mode b5-02 Proportional gain (P) PID Gain b5-03 Integral (I) time PID I Time b5-04 Integral (I) limit PID I Limit b5-05 Derivative (D) time PID D Time Control Methods Description Setting Range Factory Setting Change during Operation 0: Disabled 1: Enabled (Deviation is Dcontrolled.) 2: Enabled (Feedback value is D-controlled.) 3: PID control enabled (frequency reference + PID output, D control of deviation) 4: PID control enabled (frequency reference + PID output, D control of feedback value). 0 to 4 0 Sets P-control proportional gain as a percentage. P-control is not performed when the setting is 0.00. 0.00 to 25.00 Sets I-control integral time in 1-second units. I-control is not performed when the setting is 0.0. Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 1A5H 6-107 1.00 Yes A A A A A 1A6H 6-107 0.0 to 360.0 1.0 s Yes A A A A A 1A7H 6-107 Sets the I-control limit as a percentage of the maximum output frequency. 0.0 to 100.0 100.0% Yes A A A A A 1A8H 6-107 Sets D-control derivative time in 1-second units. D-control is not performed when the setting is 0.00. 0.00 to 10.00 0.00 s Yes A A A A A 1A9H 6-107 5-15 Name Constant Number b5-06 Description Setting Range Factory Setting Sets the upper limit after PIDcontrol as a percentage of the maximum output frequency. 0.0 to 100.0 100.0% Sets the offset after PID-control as a percentage of the maximum output frequency. -100.0 to +100.0 PID first order lag time Sets the time constant for low pass filter for PID-control constant outputs in 1-second units. PID Delay Not usually necessary to set. Time V/f Open Loop Vector 1 Flux Vector Yes A A A A A 1AAH 6-107 0.0% Yes A A A A A 1ABH 6-107 0.00 to 10.00 0.00 s Yes A A A A A 1ACH 6-107 0 or 1 0 No A A A A A 1ADH 6-107 Output Level Sel Select forward/reverse for PID output. 0: PID output is forward. 1: PID output is reverse (highlights the output code) PID output gain Sets output gain. 0.0 to 25.0 1.0 No A A A A A 1AEH 6-107 0: 0 limit when PID output is negative. 1: Reverses when PID output is negative. 0 limit when reverse prohibit is selected using b1-04. 0 or 1 0 No A A A A A 1AFH 6-107 0: No detection of loss of PID feedback. 1: Detection of loss of PID feedback. Operation continues during detection, with the malfunctioning contact not operating. 2: Detection of loss of PID feedback. Coasts to stop during detection, and fault contact operates. 0 to 2 0 No A A A A A 1B0H 6-108 Sets the PID feedback loss detection level as a percent units, with the maximum output frequency at 100%. 0 to 100 0% No A A A A A 1B1H 6-108 0.0 to 25.5 1.0 s No A A A A A 1B2H 6-108 Display PID upper limit PID offset adjustment PID Offset b5-08 b5-09 b5-10 PID output characteristics selection Output Gain b5-11 PID reverse output selection Output Rev Sel Selection of PID feedback command loss detection b5-12 Fb los Det Sel b5-13 PID feedback command loss detection level Fb los Det Lvl b5-14 PID feedback command loss detection time Fb los Det Time 5-16 Open MEMOBUS Loop Page Vec- Register tor 2 V/f with PG PID Limit b5-07 Control Methods Change during Operation Sets the PID feedback loss detection level in s units. User Constant Tables Name Constant Number b5-15 Control Methods Setting Range Factory Setting Change during Operation Set the PID sleep function start level as a frequency. 0.0 to 400.0 0.0 Hz Set the delay time until the PID sleep function starts in seconds. 0.0 to 25.5 Set the accel/decel time for PID reference in seconds. 0.0 to 25.5 Description Display PID sleep function operation level Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 1B3H 6-108 0.0 s No A A A A A 1B4H 6-108 0.0 s No A A A A A 1B5H 6-108 PID Sleep Level b5-16 PID sleep operation delay time PID Sleep Time b5-17 Accel/decel time for PID reference PID SFS Time Dwell Functions: b6 User constants for dwell functions are shown in the following table. Constant Number b6-01 Name Display Control Methods Description Dwell frequency at start Dwell Ref @Start Dwell time at start b6-02 b6-03 Dwell Time @Start Dwell frequency at stop Dwell Ref @Stop Dwell time at stop b6-04 Dwell Time @Stop Run command ON OFF Output frequency b6-01 b6-03 b6-02 Setting Range Factory Setting Change during Operation 0.0 to 400.0 0.0 Hz 0.0 to 10.0 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 1B6H 4-21 6-22 0.0 s No A A A A A 1B7H 4-21 6-22 0.0 to 400.0 0.0 Hz No A A A A A 1B8H 4-21 6-22 0.0 to 10.0 0.0 s No A A A A A 1B9H 4-21 6-22 Time b6-04 The dwell function is used to output frequency temporarily when driving a motor with a heavy load. 5-17 Droop Control: b7 User constants for droop functions are shown in the following table. Name Constant Number b7-01 b7-02 5-18 Display Control Methods Description Droop control Sets the slip as a percentage gain of maximum frequency when the maximum output frequency is specified and the rated torque occurs. Droop Quan- Droop-control is not pertity formed when the setting is 0.0. Droop control Droop control responsivedelay time ness constant Droop Delay When hunting or oscillation occurs, increase the value. Time Setting Range Factory Setting Change during Operation 0.0 to 100.0 0.0 0.03 to 2.00 0.05 s Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector Yes No No No A A 1CAH No A A A A A 1A4H 4-21 6-144 4-21 6-144 User Constant Tables Energy Saving: b8 User constants for energy-saving control functions are shown in the following table. Name Constant Number b8-01 Display Energy-saving mode selection Energy Save Sel b8-02 b8-03 Energy-saving gain Energy Save Gain Control Methods Setting Range Factory Setting Change during Operation Select whether to enable or disable energy-saving control. 0: Disable 1: Enable 0 or 1 0 Set the energy-saving gain with the open-loop vector control method. 0.0 to 10.0 0.7 0.00 to 10.0 0.50 s Description Energy-saving filter time Set the energy-saving filter constant time constant with the openEnergy Save loop vector control method. *1 *2 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 1CCH 6-115 Yes No No A A A 1CDH 6-115 Yes No No A A A 1CEH 6-115 No A A No No No 1CFH 6-115 F.T Energy-saving coefficient b8-04 Energy Save COEF b8-05 Power detection filter time constant kW Filter Time b8-06 Set the maximum motor efficiency value. Set the motor rated capacity in E2-11, and adjust the value by 5% at a time until output power reaches a minimum value. Set the time constant for output power detection. Search opera- Set the limit value of the volttion voltage age control range during limiter search operation. Perform search operation to optimize operations using minute variations in voltage Search V using energy-saving control. Limit Set to 0 to disable the search operation. 100% is the motor base voltage. 0.0 to 288.20 655.00 *3 *4 0 to 2000 20 ms No A A No No No 1D0H 6-115 0 to 100 0% No A A No No No 1D1H 6-115 * 1. The factory setting is 1.0 when using flux vector control. * 2. The factory setting is 2.00 s when Inverter capacity is 55 kW min. The factory setting will change when the control method is changed. The open-loop vector 1 factory setting is given. * 3. By setting E2-11 (Motor rated output) the appropriate value will be set. * 4. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. 5-19 Zero-servo: b9 User constants for dwell functions are shown in the following table. Name Constant Number Display Zero-servo gain b9-01 Zero Servo Gain Zero-servo completion width b9-02 Zero Servo Count 5-20 Control Methods Description Setting Range Factory Setting Change during Operation Adjust the strength of the zero-servo lock. Enabled when the “zero-servo command” is set for the multi-function input. When the zero-servo command has been input and the frequency reference drop below excitation level (b2-01), a position control loop is created and the motor stops. Increasing the zero-servo gain in turn increases the strength of the lock. Increasing it by too much will cause oscillation. 0 to 100 5 Sets the output width of the P-lock completion signal. Enabled when the “zero-servo completion (end)” is set for a multi-function input. The zero-servo completion signal is ON when the current position is within the range (the zero-servo position + zeroservo completion width.) Set the allowable position displacement from the zeroservo position to 4 times the pulse rate of the PG (pulse generator, encoder) in use. 0 to 16383 10 Open MEMOBUS Loop Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No No No No A No 1DAH 6-145 No No No No A No 1DBH 6-145 Page User Constant Tables C: Autotuning Constants The following settings are made with the autotuning constants (C constants): Acceleration/deceleration times, s-curve characteristics, slip compensation, torque compensation, speed control, and carrier frequency functions. Acceleration/Deceleration: C1 User constants for acceleration and deceleration times are shown in the following table. Name Constant Number C1-01 C1-02 C1-03 C1-04 C1-05 C1-06 Display Acceleration time 1 Accel Time 1 Deceleration time 1 Decel Time 1 Acceleration time 2 Accel Time 2 Deceleration time 2 Decel Time 2 Acceleration time 3 Accel Time 3 Deceleration time 3 Decel Time 3 Acceleration time 4 C1-07 Accel Time 4 Deceleration time 4 C1-08 Decel Time 4 Emergency stop time C1-09 Fast Stop Time Control Methods Description Setting Range Factory Setting Change during Operation V/f V/f with PG Open Loop Vector 1 Flux Vector Open MEMOBUS Loop Page Vec- Register tor 2 Sets the acceleration time to accelerate from 0 to the maximum output frequency, in 1second units. Yes Q Q Q Q Q 200H 4-5 4-21 6-18 Sets the deceleration time to decelerate from the maximum output frequency to 0, in 1second units. Yes Q Q Q Q Q 201H 4-5 4-21 6-18 The acceleration time when the multi-function input “accel/decel time 1” is set to ON. Yes A A A A A 202H 4-21 6-18 The deceleration time when the multi-function input “accel/decel time 1” is set to ON. Yes A A A A A 203H 4-21 6-18 No A A A A A 204H 4-21 6-18 The deceleration time when the multi-function input “accel/decel time 2” is set to ON. No A A A A A 205H 4-21 6-18 The acceleration time when the multi-function input “accel/decel time 1” and “accel/decel time 2” are set to ON. No A A A A A 206H 4-21 6-18 The deceleration time when the multi-function input “accel/decel time 1” and “accel/decel time 2” are set to ON. No A A A A A 207H 4-21 6-18 The deceleration time when the multi-function input “Emergency (fast) stop” is set to ON. This function can be used as a stopping method when a fault has been detected. No A A A A A 208H 4-21 6-17 The acceleration time when the multi-function input “accel/decel time 2” is set to ON. 0.0 to 6000.0 10.0 s * 5-21 Name Constant Number C1-10 Control Methods Description Display Accel/decel time setting unit Acc/Dec Units 0: 0.01-second units 1: 0.1-second units Setting Range Factory Setting Change during Operation 0 or 1 1 0.0 to 400.0 0.0 Hz Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 209H 4-21 6-18 No A A A A A 20AH 4-21 6-19 Accel/decel time switching frequency C1-11 Sets the frequency for automatic acceleration/deceleration switching. Below set frequency: Accel/ decel time 4 Above set frequency: Accel/ decel time 1 Acc/Dec SW The multi-function input Freq “accel/decel time 1” or “accel/decel time 2” take priority. * The setting range for acceleration/deceleration times depends on the setting of C1-10 (Acceleration/deceleration Time Setting Unit). If C1-10 is set to 0, the setting range is 0.00 to 600.00 (s). S-curve Acceleration/Deceleration: C2 User constants for S-curve characteristics are shown in the following table. Constant Number C2-01 Name Control Methods Description Display S-curve characteristic time at acceleration start Setting Range Factory Setting Change during Operation 0.00 to 2.50 0.20 s 0.00 to 2.50 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 20BH 4-21 6-19 0.20 s No A A A A A 20CH 4-21 6-19 0.00 to 2.50 0.20 s No A A A A A 20DH 4-21 6-19 0.00 to 2.50 0.00 s No A A A A A 20EH 4-21 6-19 SCrv Acc @ Start C2-02 C2-03 S-curve characterisAll sections of the S-curve characteristic time at tic time are set in seconds units. acceleraWhen the S-curve characteristic time is tion end set, the accel/decel times will increase by only half of the S-curve characterisSCrv Acc tic times at start and end. @ End S-curve characteristic time at deceleration start Run Command Output frequency OFF ON C2-02 C2-01 C2-03 C2-04 Time SCrv Dec @ Start C2-04 S-curve characteristic time at deceleration end SCrv Dec @ End 5-22 User Constant Tables Motor Slip Compensation: C3 User constants for slip compensation are shown in the following table. Name Constant Number Display Slip compensation gain C3-01 Slip Comp Gain Slip compensation primary delay time C3-02 Slip Comp Time C3-03 Slip compensation limit Slip Comp Limit Slip compensation selection during regeneration C3-04 Slip Comp Regen C3-05 Output voltage limit operation selection Output V limit Control Methods Description Setting Range Factory Setting Change during Operation Used to improve speed accuracy when operating with a load. Usually setting is not necessary. Adjust this constant at the following times. • When actual speed is low, increase the set value. • When actual speed is high, decrease the set value. Used as the applicable control gain when using flux vector control. 0.0 to 2.5 1.0* Slip compensation primary delay time is set in ms units. Usually setting is not necessary. Adjust this constant at the following times. • Reduce the setting when slip compensation responsive is slow. • When speed is not stabilized, increase the setting. 0 to 10000 Sets the slip compensation limit as a percentage of motor rated slip. 0 to 250 0: Disabled. 1: Enabled. When the slip compensation during regeneration function has been activated, as regeneration capacity increases momentarily, it may be necessary to use a braking option (braking resistor, Braking Resistor Unit or Braking Unit.) 0: Disabled. 1: Enabled. (The motor flux will be lowered automatically when the output voltage become saturated.) Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector Yes A No A A No 20FH 4-18 6-36 No A No A No No 210H 4-18 6-36 200% No A No A No No 211H 6-36 0 or 1 0 No A No A No No 212H 6-36 0 or 1 0 No No No A A No 213H 6-36 200 ms * * The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given. 5-23 Torque Compensation: C4 User constants for torque compensation are shown in the following table. Name Constant Number C4-01 Display C4-02 Torq Comp Time C4-04 C4-05 Description Setting Range Torque com- Sets torque compensation pensation gain as a ratio. gain Usually setting is not necessary. Adjust in the following circumstances: • When the cable is long; increase the set value. • When the motor capacity is smaller than the Inverter capacity (Max. applicable motor capacity), increase the set values. 0.00 to • When the motor is oscillat2.50 Torq Comp ing, decrease the set valGain ues. Adjust the output current range at minimum speed rotation so that it does not exceed the Inverter rated output current. Do not alter the torque compensation gain from its default (1.00) when using the open-loop vector 1 control method. Torque compensation primary delay time constant C4-03 Control Methods Forward starting torque F TorqCmp@ start Reverse starting torque R TorqCmp@ start Starting torque time constant TorqCmp DelayT Factory Setting Change during Operation 1.00 V/f Open Loop Vector 1 Flux Vector Yes A A A No No 215H 4-18 6-39 No A A A No No 216H 4-18 6-39 The torque compensation delay time is set in ms units. Usually setting is not necessary. Adjust in the following circumstances: • When the motor is oscillating, increase the set values. • When the responsiveness of the motor is low, decrease the set values. 0 to 10000 Sets the forward starting torque as a percentage of the motor rated torque. 0.0 to 200.0 0.0% No No No A No No 217H - Sets the reverse starting torque as a percentage of the motor rated torque. -200.0 to 0.0 0.0% No No No A No No 218H - Sets the delay time in ms for starting torque. The filter is disabled if the time is set to 0 to 4 ms. 0 to 200 10 ms No No No A No No 219H - 20 ms * * The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given. 5-24 Open MEMOBUS Loop Page Vec- Register tor 2 V/f with PG User Constant Tables Speed Control (ASR): C5 User constants for speed control are shown in the following table. Constant Number C5-01 Name V/f Flux Vector Yes No A No A A 21BH 4-19 6-136 0.000 0.500 to s *1 10.000 Yes No A No A A 21CH 4-19 6-136 0.00 to Usually setting is not necessary. 300.00 20.00 *1 Set to change the rotational speed gain. *2 Yes No A No A A 21DH 4-19 6-137 0.000 0.500 to s *1 10.000 Yes No A No A A 21EH 4-19 6-137 Sets the upper limit for the compensation frequency for the speed control loop (ASR) to a percentage of the maximum output frequency. 0.0 to 20.0 5.0% No No A No No No 21FH 6-137 Sets the filter time constant for outputting torque references from the speed control loop (ASR). It is set in 1-second units. With open-loop vector 2 control, this ASR Delay setting is enabled only for speeds in Time the range 0 to 35 Hz. Usually setting is not necessary. 0.000 to 0.500 0.004 s No No No No A A 220H 4-19 6-137 Set the frequency for switching between Proportion Gain 1, 2 and Integral Time 1, 2 in Hz units. 0.0 to 400.0 0.0 Hz No No No No A A 221H 4-19 6-137 Set to a small value to prevent any radical load change. Set to 100% of the maximum output frequency. 0 to 400 400% No No No No A A 222H 6-137 0.000 to 0.500 0.010 s No No No No No A 4-20 231H 6-137 6-141 Description Display ASR proportional (P) gain 1 ASR integral (I) time 1 ASR proportional (P) gain 2 ASR P Gain 2 C5-04 ASR integral (I) time 2 Sets the proportional gain of the speed loop (ASR.) Sets the integral time of the speed loop (ASR) in 1-second units. ASR limit ASR Limit C5-07 ASR switching frequency ASR Gain SW Freq C5-08 ASR integral (I) limit ASR I Limit ASR primary delay time 2 C5-10 0.00 to 20.00 300.00 *2 *1 Page P=C5-01 I=C5-02 P=C5-03 I=C5-04 0 E1-04 Motor speed (Hz) ASR primary delay time C5-06 Setting Range P, I ASR I Time 2 C5-05 Open MEMOBUS Loop Vec- Register tor 2 Open Loop Vector 1 ASR I Time 1 C5-03 Change during Operation V/f with PG ASR P Gain 1 C5-02 Control Methods Factory Setting Sets the filter time constant for outputting torque references from the speed control loop (ASR). It is set in 1-second units. With open-loop vector 2 control, this ASR Delay setting is enabled only for speeds Time2 greater than 35 Hz. Usually setting is not necessary. *1 * 1. When the control method is changed, the factory settings will change. The flux vector factory settings are given. Refer to Factory Settings that Change with the Control Method (A1-02). * 2. The setting range for flux vector and open-loop vector 2 controls is 1.00 to 300.00. 5-25 Carrier Frequency: C6 User constants for the carrier frequency are shown in the following table. Constant Number C6-02 Name Display Description Carrier frequency Select carrier wave fixed pattern. selection Select F to enable detailed settings using constants C6-03 to C6-07. Carrier Setting Range Factory Setting 1 to F 6 *2 *1 2.0 to 15.0 15.0 kHz *2 *5 *1 0.4 to 15.0 15.0 kHz *2 *5 *1 00 to 99 00 Change during Operation Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector No Q Q Q Q No A A A A No A A No No A A Open Loop Vector 2 MEMOBUS Page Register 224H 4-6 4-18 6-42 No 225H 6-42 No No 226H 6-42 No No No 227H 6-42 No No No No *4 *4 *4 Q 4-6 22DH 4-20 6-42 No *4 Freq Sel C6-03 *3 C6-04 *3 Carrier Set the carrier frequency upper limit and frequency lower limit in kHz units. upper limit The carrier frequency gain is set as follows: Carrier With the vector control method, the Freq Max upper limit of the carrier frequency is fixed in C6-03. Carrier frequency lower limit Carrier Freq Min Carrier frequency proportional gain *3 Carrier Freq Gain Carrier frequency selection for openloop vector 2 control Carrier Freq Sel * * * * * 5-26 1. 2. 3. 4. 5. Output frequency x (C6-05) x K Output frequency (Max. output frequency) C6-05 C6-11 Carrier frequency K is a coefficient that depends on the setting of C6-03. C6-03 ≥ 10.0 kHz: K = 3 10.0 kHz > C6-03 ≥ 5.0 kHz: K = 2 5.0 kHz > C6-03: K = 1 Select the carrier frequency when openloop vector 2 control is used. 1: 2 kHz 2: 4 kHz 3: 6 kHz 4: 8 kHz 1 to 4 4 *1 No *4 The factory settings depend on the capacity of the Inverter. The values for a 200 V Class Inverter for 0.4 kW are given. The setting ranges depend on the capacity of the Inverter. The values for a 200 V Class Inverter for 0.4 kW are given. This constant can be monitored or set only when F is set for C6-02. Displayed in Quick Programming Mode when motor 2 is set for a multi-function input. The maximum output frequency depends on the setting for the carrier frequency (refer to page 6-43). User Constant Tables d: Reference Constants The following settings are made with the reference constants (d constants): Frequency references. Preset Reference: d1 User constants for frequency references are shown in the following table. Name Constant Number d1-01 Display Frequency reference 1 Reference 1 d1-02 Frequency reference 2 Reference 2 d1-03 Frequency reference 3 Reference 3 d1-04 Frequency reference 4 Reference 4 d1-05 Frequency reference 5 Reference 5 d1-06 Frequency reference 6 Reference 6 d1-07 Frequency reference 7 Reference 7 d1-08 Frequency reference 8 Reference 8 d1-09 Frequency reference 9 Reference 9 d1-10 Frequency reference 10 Reference 10 d1-11 Frequency reference 11 Reference 11 Control Methods Factory Setting Change during Operation Sets the frequency reference in the units used in o1-03. 0.00 Hz The frequency reference when multi-step speed reference 1 is ON for a multi-function input. Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector Yes Q Q Q Q Q 280H 4-6 6-5 0.00 Hz Yes Q Q Q Q Q 281H 4-6 6-5 The frequency reference when multi-step speed reference 2 is ON for a multi-function input. 0.00 Hz Yes Q Q Q Q Q 282H 4-6 6-5 The frequency reference when multi-step speed references 1 and 2 are ON for multi-function inputs. 0.00 Hz Yes Q Q Q Q Q 283H 4-6 6-5 The frequency when multistep speed reference 3 is ON for a multi-function input. 0.00 Hz Yes A A A A A 284H 6-5 The frequency reference when multi-step speed references 1 and 3 are ON for multi-function inputs. 0 to 0.00 Hz 400.00 Yes A A A A A 285H 6-5 The frequency reference when multi-step speed references 2 and 3 are ON for multi-function inputs. 0.00 Hz Yes A A A A A 286H 6-5 The frequency reference when multi-step speed references 1, 2, and 3 are ON for multi-function inputs. 0.00 Hz Yes A A A A A 287H 6-5 The frequency reference when multi-step speed reference 4 is ON for a multi-function input. 0.00 Hz Yes A A A A A 288H - The frequency reference when multi-step speed references 1 and 4 are ON for multi-function inputs. 0.00 Hz Yes A A A A A 28BH - The frequency reference when multi-step speed references 2 and 4 are ON for a multi-function inputs. 0.00 Hz Yes A A A A A 28CH - Description Setting Range * 5-27 Name Constant Number d1-12 Frequency reference 12 Frequency reference 13 Reference 13 d1-14 Frequency reference 14 Reference 14 d1-15 Frequency reference 15 Reference 15 d1-16 Frequency reference 16 Reference 16 d1-17 Factory Setting The frequency reference when multi-step speed references 1, 2, and 4 are ON for multi-function inputs. 0.00 Hz The frequency reference when multi-step speed references 3 and 4 are ON for multi-function inputs. The frequency reference when multi-step speed references 1, 3, and 4 are ON for multi-function inputs. Description Display Reference 12 d1-13 Control Methods Change during Operation The frequency reference when multi-step speed references 2, 3, and 4 are ON for multi-function inputs. Setting Range Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector Yes A A A A A 28DH - 0.00 Hz Yes A A A A A 28EH - 0.00 Hz Yes A A A A A 28FH - 0.00 Hz Yes A A A A A 290H - 0.00 Hz Yes A A A A A 291H - 6.00 Hz Yes Q Q Q Q Q 292H 4-6 6-5 6-84 0 to 400.00 * The frequency reference when multi-step speed references 1, 2, 3, and 4 are ON for multi-function inputs. Jog frequency The frequency reference reference when the jog frequency reference selection, FJOG comJog mand, or RJOG command is Reference ON. Note The unit is set in o1-03 (Frequency units of reference setting and monitor). The default for o1-03 is 0 (increments of 0.01 Hz). * The setting range for open-loop vector 2 control is 0 to 66.0 (0 to 132.0 for PRG: 103) Reference Limits: d2 User constants for frequency reference limits are shown in the following table. Name Constant Number d2-01 Display Frequency reference upper limit Ref Upper Limit d2-02 Frequency reference lower limit Ref Lower Limit d2-03 Master speed reference lower limit Ref1 Lower Limit 5-28 Control Methods Description Setting Range Factory Setting Change during Operation Set the output frequency upper limit as a percent, taking the max. output frequency to be 100%. 0.0 to 110.0 100.0% Sets the output frequency lower limit as a percentage of the maximum output frequency. 0.0 to 110.0 Set the master speed reference lower limit as a percent, taking the max. output frequency to be 100%. 0.0 to 110.0 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 289H 6-34 6-79 0.0% No A A A A A 28AH 6-34 6-79 0.0% No A A A A A 293H 6-34 6-79 User Constant Tables Jump Frequencies: d3 User constants for jump frequencies are shown in the following table. Name Constant Number d3-01 Display Jump frequency 1 Jump Freq 1 d3-02 Jump frequency 2 Jump Freq 2 d3-03 Jump frequency 3 Jump Freq 3 d3-04 Control Methods Description Set the center values of the jump frequencies in Hz. This function is disabled by setting the jump frequency to 0 Hz. Always ensure that the following applies: d3-01 ≥ d3-02 ≥ d3-03 Operation in the jump frequency range is prohibited but during acceleration and deceleration, speed changes smoothly without jump. Jump freSets the jump frequency quency width bandwidth in Hz. The jump frequency will be Jump Bandthe jump frequency ± d3-04. width Setting Range 0.0 to 400.0 0.0 to 20.0 Factory Setting Change during Operation 0.0 Hz Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 294H 4-21 6-31 0.0 Hz No A A A A A 295H 4-21 6-31 0.0 Hz No A A A A A 296H 4-21 6-31 1.0 Hz No A A A A A 297H 4-21 6-31 Reference Frequency Hold: d4 User constants for the reference frequency hold function are shown in the following table. Name Constant Number Display Frequency reference hold function selection d4-01 MOP Ref Memory + - Speed limits d4-02 Trim Control Lvl Control Methods Description Setting Range Factory Setting Change during Operation Sets whether or not frequencies on hold will be recorded. 0: Disabled (when operation is stopped or the power is turned on again starts at 0.) 1: Enabled (when operation is stopped or the power is turned on again starts at the previous hold frequency.) This function is available when the multi-function inputs “accel/decel Ramp Hold” or “up/down” commands are set. 0 or 1 0 Set the frequency to be added to or subtracted from the analog frequency reference as a percent, taking the maximum output frequency to be 100%. Enabled when the increase (+) speed command or decrease (-) speed command is set for a multi-function input. 0 to 100 10% Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 298H 6-78 No A A A A A 299H 6-82 5-29 Torque Control: d5 User constants for the torque control are shown in the following table. Name Constant Number Display Torque control selection d5-01 Torq Control Sel Torque reference delay time d5-02 Torq Ref Filter Speed limit selection d5-03 Speed Limit Sel Speed limit d5-04 Speed Lmt Value Speed limit bias d5-05 5-30 Speed Lmt Bias Control Methods Description Setting Range Factory Setting Change during Operation 0: Speed control (C5-01 to C5-07) 1: Torque control This function is only available in flux vector control method. To use the function for switching between speed and torque control, set to 0 and set the multi-function input to “speed/torque control change.” 0 or 1 0 Set the torque reference delay time in ms units. This function can be used to adjust the noise of the torque control signal or the responsiveness with the host controller. When oscillation occurs during torque control, increase the set value. 0 to 1000 Set the speed limit command method for the torque control method. 1: The analog input limit from a frequency reference 2: Limited by d5-04 constant setting values. Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No No No No A A 29AH 6-127 0* No No No No A A 29BH 6-127 1 or 2 1 No No No No A A 29CH 6-127 Set the speed limit during torque control as a percentage of the maximum output frequency. This function is enabled when d5-03 is set to 2. Directions are as follows. +: Run Command direction -: Run Command opposite direction -120 to +120 0 No No No No A A 29DH 6-127 Set the speed limit bias as a percentage of the maximum output frequency. Bias is given to the specified speed limit. It can be used to adjust the margin for the speed limit. 0 to 120 10 No No No No A A 29EH 6-127 User Constant Tables Name Constant Number Description Setting Range Factory Setting Set the delay time from inputting the multi-function input “speed/torque control change” (from On to OFF or OFF to ON) until the control is actually changed, in ms units. This function is enabled when the multi-function input “speed/torque control change” is set. In the speed/ torque control switching timer, the analog inputs hold the values of when the “speed/torque control change” changes. Always be sure to allow time for this process to finish completely. 0 to 1000 0 0: Disabled 1: Enabled Usually, use a setting of 1 (enabled). Be sure to enable this setting when rotating the motor in the same direction as the speed limit (winding operation). 0 or 1 1 Display Speed/torque control switching timer d5-06 Ref Hold Time d5-07 Control Methods Change during Operation Rotation direction limit operation selection Drctn SpdLmt Sel Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No No No No A A 29FH No No No No No A 2A6H 6-128 6-128 * The factory setting will change when the control method is changed. The flux vector factory setting is given. Field Weakening: d6 User constants for the field weakening command are shown in the following table. Name Constant Number Display Field weakening level d6-01 Field-Weak Lvl Field frequency d6-02 Field-Weak Freq Control Methods Description Setting Range Factory Setting Change during Operation Set the Inverter output voltage when the field weakening command is input. It is enabled when the field weakening command is set for a multi-function input. Set the level as a percentage taking the voltage set in the V/f pattern as 100%. 0 to 100 80% Set the lower limit in hertz of the frequency range where field control is valid. The field weakening command is valid only at frequencies above this setting and only when the speed is in agreement with the current speed reference. 0.0 to 400.0 0.0 Hz Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A No No No 2A0H - No A A No No No 2A1H - 5-31 Name Constant Number Display d6-03 Field forcing function selection Field Force Sel AφR time constant d6-05 A PHI R Filter Field forcing limit d6-06 5-32 FieldForce Limit Control Methods Description Setting Range Factory Setting Change during Operation Set the field forcing function. 0: Disabled 1: Enabled 0 or 1 0 No Set the factor to multiple times the secondary circuit time constant of the motor to achieve the AφR time constant. AφR time constant = Secondary circuit time constant x d6-05 AφR will not function when d6-05 is 0. If d6-05 is not 0, the lower limit of the value will be internally adjusted to 200 ms in the Inverter. 0.00 to 10.00 1.00 No No No Set the excitation current reference’s upper limit for field forcing. Set the limit as a percentage, taking the motor’s no-load current as 100%. Enabled for operation other than DC excitation. Usually, there is no need to change this setting. 100 to 400 400% No No No V/f V/f with PG No No Open Loop Vector 1 Flux Vector Open MEMOBUS Loop Page Vec- Register tor 2 No A A 2A2H - No No A 2A4H - A A A 2A5H - A User Constant Tables E: Motor Constant Constants The following settings are made with the motor constant constants (E constants): V/f characteristics and motor constants. V/f Pattern: E1 User constants for V/f characteristics are shown in the following table. Constant Number E1-01 Name E1-04 Description Display Input voltage setting Input Voltage V/f pattern selection E1-03 Control Methods V/F Selection Set the Inverter input voltage in 1 volt. This setting is used as a reference value in protection functions. 0 to E: Select from the 15 preset patterns. F: Custom user-set patterns (Applicable for settings E1-04 to E1-10.) Max. output frequency Max Frequency E1-05 E1-06 Max. voltage Max Voltage Base frequency Base Frequency Mid. output frequency E1-07 E1-08 E1-09 E1-10 Mid Frequency A Min. output frequency voltage Min Voltage Factory Setting 155 to 255 200 V *1 *1 Open MEMOBUS Loop Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No Q Q Q Q Q 300H 4-5 6-120 Page 0 to F F No Q Q No No No 302H 6-120 40.0 to 400.0 60.0 Hz No Q Q Q Q Q 303H 6-120 *5 *2 0.0 to 255.0 200.0 V No Q Q Q Q Q 304H 6-120 *1 *1*2 0.0 to 400.0 60.0 Hz No Q Q Q Q Q 305H 6-120 *5 *2 0.0 to 400.0 3.0 Hz No A A A No No 306H 6-120 No A A A No No 307H 4-18 6-120 No Q Q Q A Q 308H 6-120 No A A A No No 309H 4-18 6-120 Output voltage (V) VMAX (E1-05) (V BASE) (E1-13) VC (E1-08) VMIN (E1-10) FMIN (E1-09) FB (E1-07) FA FMAX (E1-06) (E1-04) Frequency (Hz) To set V/f characteristics in a straight line, set the same values for E1-07 and E1-09. In this case, the Mid. output setting for E1-08 will be disrefrequency garded. voltage Always ensure that the four frequencies are set in the following Mid manner: Voltage A E1-04 (FMAX) ≥ E1-06 (FA) > E1Min. output 07 (FB) ≥ E1-09 (FMIN) frequency Min Frequency Setting Range Change during Operation 0.0 to 255.0 *1 0.0 to 400.0 *5 0.0 to 255.0 *1 *2 11.0 V *1 *2 0.5 Hz *2 2.0 V *1 *2 5-33 Constant Number Name Display Control Methods Description Mid. output frequency 2 E1-11 E1-12 E1-13 * * * * * 1. 2. 3. 4. 5. Mid Frequency B Setting Range Factory Setting 0.0 to 400.0 0.0 Hz *3 *5 Mid. output Set only to fine-adjust V/f for the frequency output range. Normally, this setting voltage 2 is not required. Mid Voltage B Base voltage 0.0 to 255.0 0.0 to 255.0 Base Voltage 0.0 V *3 *1 0.0 V *4 *1 Change during Operation Open MEMOBUS Loop Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 30AH 6-121 No A A A A A 30BH 6-121 No A A Q Q Q 30CH 6-121 Page These are values for a 200 V Class Inverter. Values for a 400 V Class Inverter are double. The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given. E1-11 and E1-12 are disregarded when set to 0.0. E1-13 is set to the same value as E1-05 by autotuning. The setting range for open-loop vector 2 control is 0 to 66.0 (0 to 132.0 for PRG: 103). Motor Setup: E2 User constants for motor 1 are shown in the following table. Name Constant Number Display Motor rated current E2-01 Motor Rated FLA Motor rated slip E2-02 E2-03 E2-04 E2-05 Motor Rated Slip Motor noload current No-Load Current Number of motor poles Number of Poles Motor lineto-line resistance Term Resistance 5-34 Control Methods Description Sets the motor rated current in 1 A units. These set values will become the reference values for motor protection, torque limits and torque control. This constant is automatically set during autotuning. Sets the motor rated slip in Hz units. These set values will become the reference values for slip compensation. This constant is automatically set during autotuning. Sets the motor no-load current in 1 A units. This constant is automatically set during autotuning. Setting Range Factory Setting 0.32 to 6.40 1.90 A *2 *1 0.00 to 2.90 Hz *1 20.00 0.00 to 1.89 *3 1.20 A *1 Change during Operation No V/f V/f with PG Open Loop Vector 1 Flux Vector Q Q Q Q Open MEMOBUS Loop Page Vec- Register tor 2 Q 30EH 4-5 6-57 6-117 No A A A A A 30FH 6-115 6-117 No A A A A A 310H 6-117 Sets the number of motor poles. This constant is automatically set during autotuning. 2 to 48 4 poles No No Q No Q Q 311H 6-117 Sets the motor phase-to-phase resistance in Ω units. This constant is automatically set during autotuning. 0.000 to 65.000 9.842 Ω No A A A A A 312H 6-117 *1 User Constant Tables Name Constant Number Display Motor leak inductance E2-06 E2-07 Leak Inductance Motor iron saturation coefficient 1 Saturation Comp1 E2-08 Motor iron saturation coefficient 2 Saturation Comp2 Motor mechanical loss E2-09 Mechanical Loss E2-10 Motor iron loss for torque compensation Control Methods Change during Operation Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No No No A A A 313H 6-117 0.50 No No No A A A 314H 6-117 0.75 No No No A A A 315H 6-117 A A 316H - Description Setting Range Factory Setting Sets the voltage drop due to motor leakage inductance as a percentage of the motor rated voltage. This constant is automatically set during autotuning. 0.0 to 40.0 18.2% Sets the motor iron saturation coefficient at 50% of magnetic flux. This constant is automatically set during autotuning. 0.00 to 0.50 Sets the motor iron saturation coefficient at 75% of magnetic flux. This constant is automatically set during autotuning. 0.00 to 0.75 *1 Sets motor mechanical loss as a percentage of motor rated output (W). Usually setting is not necessary. Adjust in the following circumstances: • When torque loss is large due to motor bearing. • When the torque loss in the pump or fan is large. The set mechanical loss will compensate for torque. 0.0 to 10.0 Sets motor iron loss in W units. 0 to 65535 14 W Set the rated output of the motor in units of 0.01 kW. This constant is automatically set during autotuning. 0.00 to 650.00 0.40 Sets the motor iron saturation coefficient at 130% of magnetic flux. This constant is automatically set during autotuning. 1.30 to 1.60 No 0.0 No No No A *1 No A A No No No 317H 6-118 No Q Q Q Q Q 318H 6-115 No No No A A A 328H 6-118 Tcomp Iron Loss E2-11 E2-12 Motor rated output Mtr Rated Power Motor iron saturation coefficient 3 Saturation Comp3 *4 1.30 * 1. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. * 2. The setting range is from 10% to 200% of the Inverter rated output current. The value for a 200 V Class Inverter for 0.4 kW is given. For the motor no-load current, set E2-03 to a value less than that of E2-01. * 3. The setting range depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. The upper limit depends on the setting of E2-01. * 4. The same capacity as that of the Inverter will be set if the constants are initialized. 5-35 Motor 2 V/f Pattern: E3 User constants for motor 2 V/f characteristics are shown in the following table. Constant Number E3-01 Name Display Motor 2 control method selection Control Method 5-36 Control Methods Description 0: V/f control 1: V/f control with PG 2: Open-loop vector control 3: Flux vector control 4: Open-loop vector 2 control Setting Range Factory Setting Change during Operation 0 to 4 2 No V/f V/f with PG Open Loop Vector 1 Flux Vector A A A A Open MEMOBUS Loop Page Vec- Register tor 2 A 319H - User Constant Tables Constant Number E3-02 Name Control Methods Description Display Motor 2 max. output frequency (FMAX) Setting Range 40.0 to 400.0 *3 Factory Setting Change during Operation 60.0 Hz MEMOBUS Page Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 31AH - No A A A A A 31BH - No A A A A A 31CH - No A A A No No 31DH - No A A A No No 31EH - No A A A A A 31FH - No A A A No No 320H - Max Frequency E3-03 Motor 2 max. voltage (VMAX) Max Voltage E3-04 Motor 2 max. voltage frequency (FA) Base Frequency E3-05 Motor 2 mid. output frequency 1 (FB) Mid Frequency E3-06 Motor 2 mid. output frequency voltage 1 (VC) Mid Voltage E3-07 Motor 2 min. output frequency (FMIN) Output voltage (V) 0.0 to 255.0 200.0 V *1 *2 0.0 to 400.0 60.0 Hz 0.0 to 400.0 3.0 Hz VMAX E3-03 VC E3-06 VMIN E3-08 FMIN E3-07 FB E3-05 FMAX FA E3-04 E3-02 *2 Frequency (Hz) To set V/f characteristics in a straight line, set the same values for E3-05 and E3-07. In this case, the setting for E3-06 will be disregarded. Always ensure that the four frequencies are set in the following manner: E3-02 (FMAX) ≥ E3-04 (FA) > E305 (FB) > E3-07 (FMIN) 0.0 to 255.0 *1 0.0 to 400.0 11.0 V *1 0.5 Hz *2 Min Frequency E3-08 Motor 2 min. output frequency voltage (VMIN) 0.0 to 255.0 *1 2.0 V *1 Min Voltage * 1. These are values for a 200 V Class Inverter. Values for a 400 V Class Inverter are double. * 2. The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given. * 3. The setting range for open-loop vector 2 control is 0 to 66.0 (0 to 132.0 for PRG: 103). 5-37 Motor 2 Setup: E4 User constants for motor 2 are shown in the following table. Name Constant Number E4-01 E4-02 E4-03 E4-04 Display Control Methods Description Motor 2 rated Sets the motor rated current in current 1 A units. These set values will become the reference values for motor Motor Rated protection, torque limits and torque control. FLA This constant is automatically set during autotuning. Motor 2 rated Sets the motor rated slip in slip Hz units. These set values will become the reference values for slip Motor Rated compensation. Slip This constant is automatically set during autotuning. Motor 2 noload current No-Load Current Sets the motor no-load current in 1 A units. This constant is automatically set during autotuning. Motor 2 number of poles Sets the number of motor (number of poles. poles) This constant is automatically set during autotuning. Number of Setting Range Factory Setting 0.32 to 6.40 1.90 A *2 *1 0.00 to 2.90 Hz *1 20.00 0.00 to 1.89 *3 1.20 A *1 Change during Operation Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 321H 6-57 No A A A A A 322H - No A A A A A 323H - 2 to 48 4 poles No No A No A A 324H - Sets the motor phase-to-phase resistance in Ω units. This constant is automatically set during autotuning. 0.000 to 65.000 9.842 Ω No A A A A A 325H - Sets the voltage drop due to motor leakage inductance as a percentage of the motor rated voltage. This constant is automatically set during autotuning. 0.0 to 40.0 18.2% No No No A A A 326H - Motor 2 rated Set the rated output of the capacity motor in units of 0.01 kW. This constant is automatically Mtr Rated set during autotuning. Power 0.00 to 650.00 0.40 No A A A A A 327H - Poles E4-05 Motor 2 lineto-line resistance Term Resistance Motor 2 leak inductance E4-06 E4-07 Leak Inductance *1 *1 *4 * 1. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. * 2. The setting range is from 10% to 200% of the Inverter rated output current. The value for a 200 V Class Inverter for 0.4 kW is given. * 3. If a multi-function input is set for motor 2 (H1- = 16), the setting range will depend upon the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. The upper limit depends on the setting of E4-01. * 4. The same capacity as that of the Inverter will be set if the constants are initialized. 5-38 User Constant Tables F: Option Constants The following settings are made with the option constants (F constants): Settings for option boards PG Option Setup: F1 User constants for the PG Speed Control Board are shown in the following table. Name Constant Number Display PG constant F1-01 PG Pulses/ Rev Operation selection at PG open circuit (PGO) F1-02 PG Fdbk Loss Sel Operation selection at overspeed (OS) F1-03 PG Overspeed Sel Operation selection at deviation F1-04 PG Deviation Sel Control Methods Description Setting Range Factory Setting Change during Operation Sets the number of PG (pulse generator or encoder) pulses. Sets the number of pulses per motor revolution. 0 to 60000 600 Sets the PG disconnection stopping method. 0: Ramp to stop (Deceleration stop using Deceleration Time 1, C102.) 1: Coast to stop 2: Fast stop (Emergency stop using the deceleration time in C1-09.) 3: Continue operation (To protect the motor or machinery, do not normally make this setting.) 0 to 3 Sets the stopping method when an overspeed (OS) fault occurs. 0: Ramp to stop (Deceleration stop using Deceleration Time 1, C102.) 1: Coast to stop 2: Fast stop (Emergency stop using the deceleration time in C1-09.) 3: Continue operation (To protect the motor or machinery, do not normally make this setting.) Sets the stopping method when a speed deviation (DEV) fault occurs. 0: Ramp to stop (Deceleration stop using Deceleration Time 1, C102.) 1: Coast to stop 2: Fast stop (Emergency stop using the deceleration time in C1-09.) 3: Continue operation (DEV is displayed and operation continued.) Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No No Q No Q No 380H 6-158 1 No No A No A No 381H 6-158 0 to 3 1 No No A No A A 382H 6-158 0 to 3 3 No No A No A A 383H 6-158 5-39 Name Constant Number PG Rotation Sel PG division rate (PG pulse monitor) F1-06 F1-08 Overspeed detection level Overspeed detection delay time PG Overspd Time F1-10 Excessive speed deviation detection level PG Deviate Level F1-11 Excessive speed deviation detection delay time PG Deviate Time 5-40 Factory Setting 0: Phase A leads with Forward Run Command. (Phase B leads with Reverse Run Command.) 1: Phase B leads with Forward Run Command. (Phase A leads with Reverse Run Command.) 0 or 1 0 1 to 132 Sets the division ratio for the PG speed control board pulse output. Division ratio = (1+ n) /m (n=0 or 1 m=1 to 32) n m Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No No A No A No 384H 6-158 1 No No A No A No 385H 6-159 0 or 1 0 No No A No No No 386H 6-159 0 to 120 115% No No A No A A 387H 6-159 No No A No A A 388H 6-159 6-159 This constant is only effective when a PG-B2 is used. The possible division ratio settings are: 1/32 ≤ F1-06 ≤ 1. Integral value Sets integral control during during accel/ acceleration/deceleration to decel enable/ either enabled or disabled. disable 0: Disabled (The integral function isn't used while accelerating or decelerating; it is used at PG Ramp PI/I constant speeds.) Sel 1: Enabled (The integral function is used at all times.) PG Overspd Level F1-09 Setting Range F1-06 PG Output Ratio F1-07 Description Display PG rotation F1-05 Control Methods Change during Operation Sets the overspeed detection method. Frequencies above that set for F1-08 (set as a percentage of the maximum output frequency) that continue to exceed this frequency for the time set in F1-09 are detected as overspeed faults. Sets the speed deviation detection method. Any speed deviation above the F1-10 set level (set as a percentage of the maximum output frequency) that continues for the time set in F1-11 is detected as a speed deviation. Speed deviation is the difference between actual motor speed and the reference command speed. 0.0 to 2.0 0.0 s 0 to 50 10% No No A No A A 389H 0.0 to 10.0 0.5 s No No A No A A 38AH 6-159 * User Constant Tables Name Constant Number Display Control Methods Setting Range Description F1-12 Number of PG gear teeth Sets the number of teeth on the gears if there are gears 1 between the PG and the PG # Gear motor. Teeth1 F1-13 Number of F1-01 F1-12 PG gear teeth A gear ratio of 1 will be used 2 if either of these constants is PG # Gear set to 0. Teeth2 F1-14 PG open-cir- Used to set the PG disconneccuit detection tion detection time. PGO will time be detected if the detection time continues beyond the set PGO Detect time. Time Input pulses from PG 60 F1-13 Factory Setting Change during Operation 0 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No No A No No No 38BH 6-159 0 No No A No No No 38CH 6-159 2.0 s No No A No A No 38DH 6-159 0 to 1000 0.0 to 10.0 * When the control method is changed, the factory setting will change. The flux vector factory setting is given. Analog Reference Board: F2 User constants for the Analog Reference Board are shown in the following table. Name Constant Number Display Bi-polar or uni-polar input selection F2-01 AI-14 Input Sel Control Methods Description Setting Range Factory Setting Change during Operation Sets the functions for channel 1 to 3 which are effective when the AI-14B Analog Reference Board is used. 0: 3-channel individual (Channel 1: terminal A1, Channel 2: terminal A2, Channel 3: terminal A3) 1: 3-channel addition (Addition values are the frequency reference) When set to 0, select 1 for b101. In this case the multifunction input “Option/ Inverter selection” cannot be used. 0 or 1 0 No V/f V/f with PG Open Loop Vector 1 Flux Vector A A A A Open MEMOBUS Loop Page Vec- Register tor 2 A 38FH 6-165 5-41 Digital Reference Board: F3 User constants for the Digital Reference Board are shown in the following table. Name Constant Number Display Digital input option F3-01 DI Input 5-42 Control Methods Description Setting Range Factory Setting Change during Operation Sets the Digital Reference Board input method. 0: BCD 1% unit 1: BCD 0.1% unit 2: BCD 0.01% unit 3: BCD 1 Hz unit 4: BCD 0.1 Hz unit 5: BCD 0.01 Hz unit 6: BCD special setting (5digit input) 7: Binary input 6 is only effective when the DI-16H2 is used. When o1-03 is set to 2 or higher, the input will be BCD, and the units will change to the o1-03 setting. 0 to 7 0 No V/f V/f with PG Open Loop Vector 1 Flux Vector A A A A Open MEMOBUS Loop Page Vec- Register tor 2 A 390H 6-165 User Constant Tables Analog Monitor Boards: F4 User constants for the Analog Monitor Board are shown in the following table. Name Constant Number F4-01 F4-02 F4-03 F4-04 F4-05 Display Channel 2 output monitor bias AO Ch2 Bias F4-07 Analog output signal level for channel 1 2 Open MEMOBUS Loop Page Vec- Register tor 2 V/f Open Loop Vector 1 Flux Vector No A A A A A 391H 6-89 1.00 Yes A A A A A 392H 6-89 3 No A A A A A 393H 6-89 0.00 to 2.50 0.50 Yes A A A A A 394H 6-89 Sets the channel 1 item bias to 100%/10 V when the Analog Monitor Board is used. -10.0 to 10.0 0.0 Yes A A A A A 395H 6-89 Sets the channel 2 item bias to 100%/10 V when the Analog Monitor Board is used. -10.0 to 10.0 0.0 Yes A A A A A 396H 6-89 0: 0 to 10 V 1: -10 to +10 V 0 or 1 0 No A A A A A 397H 6-89 0: 0 to 10 V 1: -10 to +10 V 0 or 1 0 No A A A A A 398H 6-89 Effective when the Analog Monitor Board is used. Monitor selection: Set the number of the monitor AO Ch1 item to be output. (U1-) Select Gain: Set the multiple of 10 V for Channel 1 outputting monitor items. gain 4, 10 to 14, 25, 28, 34, 39, 40 AO Ch1 Gain cannot be set. 29 to 31 and 41 are not used. When the AOChannel 2 12 Analog Monitor Board is monitor used, outputs of ± 10 V are selection possible. To output ± 10 V, set AO Ch2 F4-07 or F4-08 to 1. When Select the AO-08 Analog Monitor Board is used, only outputs of Channel 2 0 to +10 V are possible. gain A meter calibration function AO Ch2 Gain is available. Channel 1 output monitor bias Factory Setting V/f with PG Description Channel 1 monitor selection AO Ch1 Bias F4-06 Control Methods Change during Operation Setting Range 1 to 45 1 to 99 0.00 to 2.50 1 to 45 1 to 99 AO Opt Level Sel F4-08 Analog output signal level for channel 2 AO Opt Level Sel 5-43 Digital Output Boards (DO-02C and DO-08): F5 User constants for the Digital Output Board are shown in the following table. Name Effective when a Digital Output Board (DO-02C or DO08) is used. Set the number of the multifunction output to be output. 0 to 37 Effective when a DO-08 Digital Output Board is used. Set the number of the multifunction output to be output. A A A 399H 1 No A A A A A 39AH 6-162 0 to 37 2 No A A A A A 39BH 6-162 Effective when a DO-08 Digital Output Board is used. Set the number of the multifunction output to be output. 0 to 37 4 No A A A A A 39CH 6-162 Effective when a DO-08 Digital Output Board is used. Set the number of the multifunction output to be output. 0 to 37 6 No A A A A A 39DH 6-162 Effective when a DO-08 Digital Output Board is used. Set the number of the multifunction output to be output. 0 to 37 37 No A A A A A 39EH 6-162 0 to 37 0F No A A A A A 39FH 6-163 Effective when a DO-08 Digital Output Board is used. Set the number of the multifunction output to be output. 0 to 37 0F No A A A A A 3A0H 6-163 Effective when a DO-08 Digital Output Board is used. Set the output mode. 0: 8-channel individual outputs DO-08 Selec- 1: Binary code output tion 2: Output according to F5-01 to F5-08 settings. 0 to 2 0 No A A A A A 3A1H 6-163 Channel 2 output selection Channel 3 output selection Channel 4 output selection DO Ch4 Select Channel 5 output selection DO Ch5 Select Channel 6 output selection DO Ch6 Select Channel 7 output selection DO Ch7 Select F5-08 0 A DO Ch3 Select F5-07 0 to 37 A DO Ch2 Select F5-06 Effective when a Digital Output Board (DO-02C or DO08) is used. Set the number of the multifunction output to be output. Open MEMOBUS Loop Page Vec- Register tor 2 No DO Ch1 Select F5-05 Factory Setting V/f F5-01 F5-04 Setting Range Flux Vector Channel 1 output selection F5-03 Description Open Loop Vector 1 Display F5-02 Control Methods Change during Operation V/f with PG Constant Number Channel 8 output selection DO Ch8 Select Effective when a DO-08 Digital Output Board is used. Set the number of the multifunction output to be output. 6-162 DO-08 output mode selection F5-09 5-44 User Constant Tables Communications Option Boards: F6 User constants for a Communications Option Board are shown in the following table. Name Constant Number F6-01 F6-02 Control Methods Setting Range Factory Setting Change during Operation 0 to 3 1 0: Always detect 1: Detect during operation 0 or 1 0: Deceleration stop using deceleration time in C102 1: Coast to stop 2: Emergency stop using deceleration time in C109 3: Continue operation - Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 3A2H - 0 No A A A A A 3A3H - 0 to 3 1 No A A A A A 3A4H - 0 to 60000 0 No A A A A A 3A5H - 0: Torque reference/torque limit from transmission disabled. 1: Torque reference/torque limit from transmission enabled. 0 or 1 0 No No No No A A 3A7H - Operation Set the stopping method for selection after SI-T WDT errors (E5). SI-T WDT 0: Deceleration stop using error deceleration time in C102 1: Coast to stop 2: Emergency stop using SI-T deceleration time in C1WDTErr Sel 09 3: Continue operation 0 to 3 1 No A A A A A 3B6H - 2 to 10 2 No A A A A A 3B7H - Display Description Operation Set the stopping method for selection after communications errors. communica0: Deceleration stop using tions error deceleration time in C102 1: Coast to stop 2: Emergency stop using BUS Fault deceleration time in C1Sel 09 3: Continue operation Input level of external fault from Communications Option Board EF0 Detection F6-03 Stopping method for external fault from Communications Option Board EF0 Fault Action F6-04 Trace sampling from Communications Option Board Trace Sample Tim F6-06 Torque reference/torque limit selection from optical option Torq Ref/Lmt Sel F6-08 ∗ F6-09 ∗ Number of SI-T BUS error detection Set the number which SI-T detects BUS errors. SI-T BUS DET Ctr * Applicable for G7-Series Inverters with software versions PRG: 1038 or later. Refer to MECHATROLINK COMMUNICATIONS INTERFACE CARD INSTRUCTIONS (TOBPC73060008) for details. 5-45 H: Terminal Function Constants The following settings are made with the terminal function constants (H constants): Settings for external terminal functions. Multi-function Contact Inputs: H1 User constants for multi-function contact inputs are shown in the following tables. Name Constant Number Display H1-01 Terminal S3 function selection Terminal S3 Sel H1-02 Terminal S4 function selection Terminal S4 Sel H1-03 Terminal S5 function selection Terminal S5 Sel H1-04 Terminal S6 function selection Terminal S6 Sel H1-05 Terminal S7 function selection Terminal S7 Sel H1-06 Terminal S8 function selection Terminal S8 Sel H1-07 Terminal S9 function selection Terminal S9 Sel H1-08 Terminal S10 function selection Terminal S10 Sel 5-46 Control Methods Description Setting Range Factory Setting Change during Operation Multi-function contact input 1 0 to 79 24 Multi-function contact input 2 0 to 79 Multi-function contact input 3 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 400H - 14 No A A A A A 401H - 0 to 79 3 (0)* No A A A A A 402H - Multi-function contact input 4 0 to 79 4 (3)* No A A A A A 403H - Multi-function contact input 5 0 to 79 6 (4)* No A A A A A 404H - Multi-function contact input 6 0 to 79 8 (6)* No A A A A A 405H - Multi-function contact input 7 0 to 79 5 No A A A A A 406H - Multi-function contact input 8 0 to 79 32 No A A A A A 407H - User Constant Tables Name Constant Number Display H1-09 Terminal S11 function selection Terminal S11 Sel H1-10 Terminal S12 function selection Terminal S12 Sel Control Methods Description Setting Range Factory Setting Change during Operation Multi-function contact input 9 0 to 79 7 Multi-function contact input 10 0 to 79 15 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 408H - No A A A A A 409H - * The factory settings in the parentheses are for 3-wire sequence. Multi-function Contact Input Functions Control Methods Setting Value Function V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 Page 0 3-wire sequence (Forward/Reverse Run Command) Yes Yes Yes Yes Yes 6-11 1 Local/Remote selection (ON: Local, OFF: Remote) Yes Yes Yes Yes Yes 6-76 2 Option/Inverter selection (ON: Option board) Yes Yes Yes Yes Yes 6-83 6-164 3 Multi-step speed reference 1 When H3-05 is set to 0, this function is combined with the master/auxiliary speed switch. Yes Yes Yes Yes Yes 6-5 4 Multi-step speed reference 2 Yes Yes Yes Yes Yes 6-5 5 Multi-step speed reference 3 Yes Yes Yes Yes Yes 6-5 6 Jog frequency command (higher priority than multi-step speed reference) Yes Yes Yes Yes Yes 6-5 7 Accel/decel time 1 Yes Yes Yes Yes Yes 6-19 8 External baseblock NO (NO contact: Baseblock at ON) Yes Yes Yes Yes Yes 6-77 9 External baseblock NC (NC contact: Baseblock at OFF) Yes Yes Yes Yes Yes 6-77 A Acceleration/deceleration ramp hold (ON: Acceleration/deceleration stopped, frequency on hold) Yes Yes Yes Yes Yes 6-78 B OH2 alarm signal input (ON: OH2 will be displayed) Yes Yes Yes Yes Yes - C Multi-function analog input selection (ON: Enable) Yes Yes Yes Yes Yes - D No V/f control with PG (ON: Speed feedback control disabled,) (normal V/f control) No Yes No No No 6-137 E Speed control integral reset (ON: Integral control disabled) No Yes No Yes Yes 6-137 F Not used (Set when a terminal is not used) - - - - - - 10 Up command (Always set with the down command) Yes Yes Yes Yes Yes 6-79 11 Down command (Always set with the up command) Yes Yes Yes Yes Yes 6-79 12 FJOG command (ON: Forward run at jog frequency d1-17) Yes Yes Yes Yes Yes 6-84 13 RJOG command (ON: Reverse run at jog frequency d1-17) Yes Yes Yes Yes Yes 6-84 14 Fault reset (Reset when turned ON) Yes Yes Yes Yes Yes 7-2 15 Emergency stop. (Normally open condition: Deceleration to stop in deceleration time set in C1-09 when ON.) Yes Yes Yes Yes Yes 6-17 5-47 Control Methods Setting Value Function V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 16 Motor switch command (Motor 2 selection) Yes Yes Yes Yes Yes - 17 Emergency stop (Normally closed condition: Deceleration to stop in deceleration time set in C1-09 when OFF) Yes Yes Yes Yes Yes 6-17 18 Timer function input (Functions are set in b4-01 and b4-02 and the timer function outputs are set in H1- and H2-.) Yes Yes Yes Yes Yes 6-105 19 PID control disable (ON: PID control disabled) Yes Yes Yes Yes Yes 6-109 1A Accel/Decel time 2 Yes Yes Yes Yes Yes 6-19 1B Constants write enable (ON: All constants can be written-in. OFF: All constants other than frequency monitor are write protected.) Yes Yes Yes Yes Yes 6-156 7-25 1C Trim control increase (ON: d4-02 frequency is added to analog frequency reference.) Yes Yes Yes Yes Yes 6-82 1D Trim control decrease (ON: d4-02 frequency is subtracted from analog frequency reference.) Yes Yes Yes Yes Yes 6-82 1E Analog frequency reference sample/hold Yes Yes Yes Yes Yes 6-83 20 to 2F External fault (Desired settings possible) Input mode: NO contact/NC contact, Detection mode: Normal/during operation Yes Yes Yes Yes Yes 6-85 30 PID control integral reset (reset when reset command is input or when stopped during PID control) Yes Yes Yes Yes Yes 6-109 31 PID control integral hold (ON: Hold) Yes Yes Yes Yes Yes 6-109 32 Multi-step speed reference 4 Yes Yes Yes Yes Yes - 34 PID soft starter ON/OFF Yes Yes Yes Yes Yes 6-109 35 PID input characteristics switch Yes Yes Yes Yes Yes 6-109 60 DC injection braking command (ON: Performs DC injection braking) Yes Yes Yes Yes Yes 6-16 61 External search command 1 (ON: Speed search from maximum output frequency) Yes No Yes No Yes 6-67 62 External search command 2 (ON: Speed search from set frequency) Yes No Yes No Yes 6-67 63 Field weakening command (ON: Field weakening control set for d6-01 and d602) Yes Yes No No No - 64 External speed search command 3 (NC contact) Yes Yes Yes Yes Yes - 65 KEB (deceleration at momentary power loss) command (NC contact) Yes Yes Yes Yes Yes - 66 KEB (deceleration at momentary power loss) command (NO contact) Yes Yes Yes Yes Yes - 67 Communications test mode (“Pass” is displayed when the communications test is passed.) Yes Yes Yes Yes Yes 6-104 68 High-slip braking (HSB) Yes Yes No No No - 71 Speed/torque control change (ON: Torque control) No No No Yes Yes 6-129 6-135 72 Zero-servo command (ON: Zero-servo) No No No Yes No 6-146 77 Speed control (ASR) proportional gain switch (ON: C5-03) No No No Yes Yes 6-137 78 Polarity reversing command for external torque reference No No No Yes Yes 6-129 79 Brake ON signal (Brake Signal)* No No No No Yes - * If the multi-function input is set to 79 and the input value is “closed,” operation will be performed with a speed specification of 0. 5-48 Page User Constant Tables Multi-function Contact Outputs: H2 User constants for multi-function outputs are shown in the following tables. Name Constant Number H2-01 Display Control Methods Setting Range Factory Setting Change during Operation 0 to 3D 0 Multi-function contact output 1 0 to 3D Multi-function contact output 2 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 40BH - 1 No A A A A A 40CH - 0 to 3D 2 No A A A A A 40DH - Multi-function contact output 3 0 to 3D 6 No A A A A A 40EH - Multi-function contact output 4 0 to 3D 10 No A A A A A 40FH - Description Terminal M1M2 function selection Multi-function contact output (contact) Term M1-M2 Sel H2-02 Terminal P1 function selection (open collector) Term P1 Sel H2-03 Terminal P2 function selection (open collector) Term P2 Sel H2-04 Terminal P3 function selection (open collector) Term P3 Sel H2-05 Terminal P4 function selection (open collector) Term P4 Sel 5-49 Multi-function Contact Output Functions Control Methods Setting Value 5-50 Function V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 Page 0 During run (ON: Run Command is ON or voltage is being output) Yes Yes Yes Yes Yes 6-86 1 Zero-speed Yes Yes Yes Yes Yes 6-86 2 Frequency agree 1 (L4-02 used.) Yes Yes Yes Yes Yes 6-51 3 Desired frequency agree 1 (ON: Output frequency = ±L4-01, L4-02 used and during frequency agree) Yes Yes Yes Yes Yes 6-51 4 Frequency (FOUT) detection 1 (ON: +L4-01 ≥ output frequency ≥ -L4-01, L4-02 used) Yes Yes Yes Yes Yes 6-51 5 Frequency (FOUT) detection 2 (ON: Output frequency ≥ +L4-01 or output frequency ≤ -L4-01, L4-02 used) Yes Yes Yes Yes Yes 6-51 6 Inverter operation ready READY: After initialization, no faults Yes Yes Yes Yes Yes - 7 During DC bus undervoltage (UV) detection Yes Yes Yes Yes Yes - 8 During baseblock (ON: during baseblock) Yes Yes Yes Yes Yes - 9 Frequency reference selection (ON: Frequency reference from Operator) Yes Yes Yes Yes Yes - A Run Command selection status (ON: Run Command from Operator) Yes Yes Yes Yes Yes - B Overtorque/undertorque detection 1 NO (NO contact: Overtorque/undertorque detection at ON) Yes Yes Yes Yes Yes 6-54 C Loss of frequency reference (Effective when 1 is set for L4-05) Yes Yes Yes Yes Yes 6-71 D Braking resistor fault (ON: Resistor overheat or braking transistor fault) Yes Yes Yes Yes Yes 6-74 E Fault (ON: Digital Operator communications error or fault other than CPF00 and CPF01 has occurred.) Yes Yes Yes Yes Yes - F Not used. (Set when the terminals are not used.) - - - - - - 10 Minor fault (ON: Alarm displayed) Yes Yes Yes Yes Yes - 11 Fault reset command active Yes Yes Yes Yes Yes - 12 Timer function output Yes Yes Yes Yes Yes 6-105 13 Frequency agree 2 (L4-04 used) Yes Yes Yes Yes Yes 6-51 14 Desired frequency agree 2 (ON: Output frequency = L4-03, L4-04 used, and during frequency agree) Yes Yes Yes Yes Yes 6-51 15 Frequency detection 3 (ON: Output frequency ≤ -L4-03, L4-04 used) Yes Yes Yes Yes Yes 6-51 16 Frequency detection 4 (ON: Output frequency ≥ -L4-03, L4-04 used) Yes Yes Yes Yes Yes 6-51 17 Overtorque/undertorque detection 1 NC (NC Contact: Torque detection at OFF) Yes Yes Yes Yes Yes 6-54 18 Overtorque/undertorque detection 2 NO (NO Contact: Torque detection at ON) Yes Yes Yes Yes Yes 6-54 19 Overtorque/undertorque detection 2 NC (NC Contact: Torque detection at OFF) Yes Yes Yes Yes Yes 6-54 1A During reverse run (ON: During reverse run) Yes Yes Yes Yes Yes - 1B During baseblock 2 (OFF: During baseblock) Yes Yes Yes Yes Yes - 1C Motor selection (Motor 2 selected) Yes Yes Yes Yes Yes - 1D During regeneration (ON: During regeneration) No No No Yes Yes - 1E Restart enabled (ON: Restart enabled) Yes Yes Yes Yes Yes 6-72 1F Motor overload (OL1, including OH3) pre-alarm (ON: 90% or more of the detection level) Yes Yes Yes Yes Yes 6-58 6-87 20 Inverter overheat (OH) pre-alarm (ON: Temperature exceeds L8-02 setting) Yes Yes Yes Yes Yes 6-87 User Constant Tables Control Methods Setting Value Function 2F*1 V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 Maintenance Time ON: The operation time of either the electrolytic capacitors or the cooling fan has reached the specified maintenance time. Yes Yes Yes Yes Yes - 30 During torque limit (current limit) (ON: During torque limit) No No Yes Yes Yes - 31 During speed limit (ON: During speed limit) No No No Yes No 6-87 32 Speed control circuit operating for torque control (except when stopped). The external torque reference will be limited if torque control is selected (internal torque reference < external torque reference). Output when the motor is rotating at the speed limit. No No No Yes Yes 6-129 33 Zero-servo end (ON: Zero-servo function completed) No No No Yes No 6-87 6-146 Frequency (FOUT) detection 5 (ON: Output frequency ≥ + L4-01 or output frequency ≤ L4-01, L4-02 used, OFF: during baseblock Yes Yes Yes Yes Yes 6-50 During run 2 (ON: Frequency output, OFF: Base block, DC injection braking, initial excitation, operation stop) Yes Yes Yes Yes Yes 6-86 Inverter's Cooling Fan Fault detected Yes Yes Yes Yes Yes 6-73 36*2 37 3D*2 Page * 1. Applicable for G7-Series Inverters with software versions PRG: 1039 or later. * 2. Applicable for G7-Series Inverters with software versions PRG: 1038 or later. Analog Inputs: H3 User constants for analog inputs are shown in the following table. Name Constant Number Display H3-01 Signal level selection (terminal A1) Term A1 Signal H3-02 H3-03 H3-04 Gain (terminal A1) Terminal A1 Gain Bias (terminal A1) Terminal A1 Bias Signal level selection (terminal A3) Term A3 Signal Control Methods Setting Range Factory Setting Change during Operation 0 or 1 0 Sets the frequency when 10 V is input, as a percentage of the maximum output frequency. 0.0 to 1000.0 Sets the frequency when 0 V is input, as a percentage of the maximum frequency. 0: 0 to 10 V 1: -10 V to 10 V [11-bit + polarity (positive/negative) input] Description 0: 0 to 10 V 1: -10V to 10 V [11-bit + polarity (positive/negative) input] Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 410H 6-28 100.0% Yes A A A A A 411H 6-28 -100.0 to +100.0 0.0% Yes A A A A A 412H 6-28 0 or 1 0 No A A A A A 413H 6-28 6-128 5-51 Name Control Methods Setting Range Factory Setting Change during Operation Select multi-function analog input function for terminal A3. Refer to the next page. 0 to 1F 2 Sets the input gain (level) when 10 V is input. Set according to the 100% value selected from H3-05. 0.0 to 1000.0 Sets the input gain (level) when 0 V is input. Set according to the 100% value selected from H3-05. Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 414H 6-28 6-128 100.0% Yes A A A A A 415H 6-28 6-128 -100.0 to +100.0 0.0% Yes A A A A A 416H 6-28 6-128 0 to 2 2 No A A A A A 417H 6-28 6-128 Select multi-function analog input function for terminal A2. Refer to the next table. 0 to 1F 0 No A A A A A 418H 6-29 6-128 H3-10 Gain Sets the input gain (level) (terminal A2) when 10 V (20 mA) is input. Set according to the 100% Terminal A2 value for the function set for Gain H3-09. 0.0 to 1000.0 100.0% Yes A A A A A 419H 6-29 6-129 H3-11 Bias Sets the input gain (level) (terminal A2) when 0 V (4 mA) is input. Set according to the 100% Terminal A2 value for the function set for Bias H3-09. -100.0 to +100.0 0.0% Yes A A A A A 41AH 6-29 6-129 0.00 to 2.00 0.03 s No A A A A A 41BH 6-29 Constant Number H3-05 Display Multi-function analog input (terminal A3) function selection Description Terminal A3 Sel H3-06 H3-07 H3-08 H3-09 Gain (terminal A3) Terminal A3 Gain Bias (terminal A3) Terminal A3 Bias Signal level selection (terminal A2) 0: 0 to 10V 1: -10V to 10V 2: 4 to 20 mA (9-bit input). Switch current and voltage Term A2 Sig- input using the switch on the nal control panel. Multi-function analog input (terminal A2) function selection Terminal A2 Sel H3-12 Analog input filter time constant Filter Avg Time 5-52 Sets primary delay filter time constant in seconds for the analog input terminal. Effective for noise control etc. User Constant Tables H3-05,H3-09 Settings Control Methods Setting Value Function Contents (100%) V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 Page 0 Add to terminal A1 Maximum output frequency Yes Yes Yes Yes Yes 6-30 6-129 1 Frequency gain Frequency reference (voltage) command value Yes Yes Yes Yes Yes 6-30 2 Auxiliary frequency reference 1 (2nd step analog) Maximum output frequency Yes Yes Yes Yes Yes 6-5 3 Auxiliary frequency reference 2 (3rd step analog) Maximum output frequency Yes Yes Yes Yes Yes 6-5 4 Voltage bias 200 V (200 V Class)/400 V (400 V Class) Yes Yes No No No - 5 Accel/decel change (reduction coefficient) Set acceleration and deceleration times (C1-01 to C1-08) Yes Yes Yes Yes Yes 6-18 6 DC injection braking current Inverter rated output current Yes Yes Yes No No 6-17 7 Overtorque/undertorque detection level Motor rated torque for vector control Inverter rated output current for V/f control Yes Yes Yes Yes Yes 6-56 8 Stall prevention level during run Inverter rated output current Yes Yes No No No 6-50 9 Frequency reference lower limit level Maximum output frequency Yes Yes Yes Yes Yes 6-35 A Jump frequency Maximum output frequency Yes Yes Yes Yes Yes 6-32 B PID feedback Maximum output frequency Yes Yes Yes Yes Yes 6-109 C PID target value Maximum output frequency Yes Yes Yes Yes Yes 6-109 D Frequency bias 2 Maximum output frequency Yes Yes Yes Yes Yes 6-31 E Motor temperature input 10 V = 100% Yes Yes Yes Yes Yes 6-61 10 Positive torque limit Motor's rated torque No No Yes Yes Yes 6-47 11 Negative torque limit Motor's rated torque No No Yes Yes Yes 6-47 12 Regenerative torque limit Motor's rated torque No No Yes Yes Yes 6-47 13 Torque reference/torque limit at speed control Motor’s rated torque No No No Yes Yes 6-129 14 Torque compensation Motor’s rated torque No No No Yes Yes 6-129 15 Positive/negative torque limit Motor's rated torque No No Yes Yes Yes 6-47 1F Analog input not used. - Yes Yes Yes Yes Yes 6-6 - - - - - - - 16 to 1E Not used 5-53 Multi-function Analog Outputs: H4 User constants for multi-function analog outputs are shown in the following table. Name Constant Number H4-01 Display Monitor selection (terminal FM) Terminal FM Sel Gain (terminal FM) H4-02 Terminal FM Gain Control Methods Description Sets the number of the monitor item to be output (U1-) from terminal FM. 4, 10 to 14, 25, 28, 34, 39, 40 cannot be set. 29 to 31 and 41 are not used. Sets the multi-function analog output 1 voltage level gain. Sets whether the monitor item output will be output in multiples of 10 V. The maximum output from the terminal is 10 V. A meter cali- Factory Setting Change during Operation 2 0.00 to 2.50 -10.0 to +10.0 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 41DH 6-88 1.00 Yes Q Q Q Q Q 41EH 4-6 6-88 0.0% Yes A A A A A 41FH 6-88 3 No A A A A A 420H 6-88 0.00 to 2.50 0.50 Yes Q Q Q Q Q 421H 4-6 6-88 -10.0 to +10.0 0.0% Yes A A A A A 422H 6-88 0 or 1 0 No A A A A A 423H 6-89 Setting Range 1 to 45 1 to 99 bration function is available.* H4-03 Bias (termi- Sets the multi-function analog nal FM) output 1 voltage level bias. Sets output characteristic up/ down parallel movement as a percentage of 10 V. Terminal The maximum output from the FM Bias terminal is 10 V. A meter calibration function is available.* H4-04 Monitor selection (terminal AM) Terminal AM Sel Gain (terminal AM) H4-05 Terminal AM Gain Sets the number of the monitor item to be output (U1-) from terminal AM. 4, 10 to 14, 25, 28, 34, 39, 40 cannot be set. 29 to 31 and 41 are not used. Set the voltage level gain for multi-function analog output 2. Set the number of multiples of 10 V to be output as the 100% output for the monitor items. The maximum output from the terminal is 10 V. A meter cali- 1 to 45 1 to 99 bration function is available.* H4-06 Bias (termi- Sets the multi-function analog nal AM) output 2 voltage level bias. Sets output characteristic up/ down parallel movement as a percentage of 10 V. Terminal The maximum output from the AM Bias terminal is 10 V. A meter calibration function is available.* H4-07 5-54 Analog output 1 signal Sets the signal output level for level selec- multi-function output 1 (terminal FM) tion 0: -10 to 10 V output AO Level 1: -10 to 10 V output Select1 User Constant Tables Name Constant Number H4-08 Display Control Methods Description Analog output 2 signal Sets the signal output level for level selec- multi-function output 2 (terminal AM) tion 0: 0 to +10 V output AO Level 1: 0 to ±10 V output Select2 Setting Range Factory Setting Change during Operation 0 or 1 0 No V/f V/f with PG Open Loop Vector 1 Flux Vector A A A A Open MEMOBUS Loop Page Vec- Register tor 2 A 424H - * The CH1 output can be adjusted when the H4-02 or H4-03 setting is displayed in Quick, Advanced, or Verify mode while the motor is stopped. The CH2 output can be adjusted when the H4-05 or H4-06 setting is displayed in Quick, Advanced, or Verify mode while the motor is stopped. For analog output, the value equivalent to 100% of output value of monitored item is multiplied by the gain setting and the set bias is added. MEMOBUS Communications: H5 User constants for MEMOBUS communications are shown in the following table. Name Constant Number H5-01 Display Slave address Serial Comm Adr Control Methods Description Set the Inverter's slave address. Setting Range 0 to 20 *1 Factory Setting Change during Operation 1F Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 425H 6-94 Communication speed selection H5-02 Set the baud rate for MEMOBUS communications of communications connection terminals. 0: 1200 bps 1: 2400 bps Serial Baud 2: 4800 bps Rate 3: 9600 bps 4: 19200 bps 0 to 4 3 No A A A A A 426H 6-94 H5-03 Communi- Set the parity for MEMOBUS cation par- communications of communiity selection cations connection terminals. 0: No parity Serial Com 1: Even parity Sel 2: Odd parity 0 to 2 0 No A A A A A 427H 6-94 Set the stopping method for communications errors. 0: Deceleration to stop using deceleration time in C1-02 1: Coast to stop 2: Emergency stop using deceleration time in C1-09 3: Continue operation 0 to 3 3 No A A A A A 428H 6-94 Set whether or not a communications timeout is to be detected as a communications error. 0: Do not detect. 1: Detect 0 or 1 1 No A A A A A 429H 6-94 Set the time from the Inverter receiving data to when the Inverter starts to send. 5 to 65 5 ms No A A A A A 42AH 6-94 H5-04 Stopping method after communication error Serial Fault Sel H5-05 Communication error detection selection Serial Flt Dtct H5-06 Send wait time Transmit WaitTIM 5-55 Name Constant Number H5-07 Display RTS control ON/ OFF RTS Control Sel H5-10 *2 Unit Selection for MEMOBUS Register 0025H MEMOBUS 25H UNIT Control Methods Setting Range Factory Setting Change during Operation Select to enable or disable RTS control. 0: Disabled (RTS is always ON) 1: Enabled (RTS turns ON only when sending) 0 or 1 1 Selects the units used for MEMOBUS registry 0025H (monitors the output voltage reference). 0: 0.1 V units 1: 1 V units 0 or 1 0 Description * 1. Set H5-01 to 0 to disable Inverter responses to MEMOBUS communications. * 2. Applicable for G7-Series Inverters with software versions PRG: 1039 or later. 5-56 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 42BH 6-94 No A A A A A 436H 6-95 User Constant Tables Pulse Train I/O: H6 User constants for pulse I/O are shown in the following table. Name Constant Number Display H6-01 Pulse train input function selection Pulse Input Sel H6-02 Pulse train input scaling PI Scaling H6-03 H6-04 H6-05 Pulse train input gain Pulse Input Gain Pulse train input bias Pulse Input Bias Pulse train input filter time PI Filter Time H6-06 Pulse train monitor selection Pulse Output Sel H6-07 Pulse train monitor scaling PO Scaling Control Methods Description 0: Frequency reference 1: PID feedback value 2: PID target value Set the number of pulses in hertz, taking the reference to be 100%. Setting Range Factory Setting Change during Operation 0 to 2 0 No V/f V/f with PG Open Loop Vector 1 Flux Vector A A A A Open MEMOBUS Loop Page Vec- Register tor 2 A 42CH 6-2 6-33 6-108 1000 to 32000 Set the input gain level as a per0.0 to cent when the pulse train set in 1000.0 H6-02 is input. 1440 Hz Yes A A A A A 42DH 6-2 6-33 100.0% Yes A A A A A 42EH 6-33 Set the input bias when the pulse train is 0. -100.0 to 100.0 0.0% Yes A A A A A 42FH 6-33 Set the pulse train input primary delay filter time constant in seconds. 0.00 to 2.00 0.10 s Yes A A A A A 430H 6-33 Select the pulse train monitor output items (value of the part of U1-). There are two types of monitor items: Speed-related items and PID-related items. 1, 2, 5, 20, 24, 36 2 Yes A A A A A 431H 6-90 Set the number of pulses output when speed is 100% in hertz. Set H6-06 to 2, and H6-07 to 0, to make the pulse train monitor output synchronously to the output frequency. 0 to 32000 1440 Hz Yes A A A A A 432H 6-91 5-57 L: Protection Function Constants The following settings are made with the protection function constants (L constants): Motor selection function, power loss ridethrough function, stall prevention function, frequency detection, torque limits, and hardware protection. Motor Overload: L1 User constants for motor overloads are shown in the following table. Name Constant Number Description Setting Range Factory Setting Sets whether the motor overload function is enabled or disabled at electric thermal overload relay. 0: Disabled 1: General-purpose motor protection 2: Inverter motor protection 3: Vector motor protection In some applications when the Inverter power supply is turned off, the thermal value is reset, so even if this constant is set to 1, protection may not be effective. When several motors are connected to one Inverter, set to 0 and ensure that each motor is installed with a protection device. 0 to 3 1 Motor pro- Sets the electric thermal detectection time tion time in seconds units. constant Usually setting is not necessary. The factory setting is 150% overload for one minute. When the motor's overload MOL Time resistance is known, also set the Const overload resistance protection time for when the motor is hot started. 0.1 to 5.0 0 to 3 Display Motor protection selection L1-01 MOL Fault Select L1-02 Alarm operation selection during motor overheating L1-03 MOL Thm Input 5-58 Control Methods Change during Operation Set H3-09 to E and select the operation when the input motor temperature (thermistor) input exceeds the alarm detection level (1.17 V). 0: Decelerate to stop using the deceleration time in C1-02. 1: Coast to stop 2: Emergency stop using the deceleration time in C1-09. 3: Continue operation (H3 on the Operator flashes). Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No Q Q Q Q Q 480H 4-5 6-57 1.0 min No A A A A A 481H 6-57 3 No A A A A A 482H 6-60 User Constant Tables Name Constant Number Display Motor overheating operation selection L1-04 MOL Filter Time L1-05 Motor temperature input filter time constant MOL Filter Time Control Methods Description Setting Range Factory Setting Change during Operation Set H3-09 to E and select the operation when the motor temperature (thermistor) input exceeds the operation detection level (2.34 V). 0: Decelerate to stop using the deceleration time in C1-02. 1: Coast to stop 2: Emergency stop using the deceleration time in C1-09. 0 to 2 1 Set H3-09 to E and set the primary delay time constant for motor temperature (thermistor) inputs in seconds. 0.00 to 10.00 0.20 s Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 483H 6-60 No A A A A A 484H 6-60 Power Loss Ridethrough: L2 User constants for power loss ridethroughs are shown in the following table. Name Constant Number Display Momentary power loss detection L2-01 PwrL Selection L2-02 Momentary power loss ridethru time Control Methods Description Setting Range Factory Setting Change during Operation 0: Disabled [main circuit undervoltage (UV1) detection] 1: Enabled [Restarted when the power returns within the time for L2-02. When L202 is exceeded, main circuit undervoltage (UV1) is detected.] 2: Enabled while CPU is operating. [Restarts when power returns during control operations. Does not detect main circuit undervoltage (UV1).] 0 to 2 0 0 to 25.5 0.1 s Ridethrough time, when Momentary Power Loss Selection (L2-01) is set to 1, in units PwrL Ride- of seconds. thru t *1 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 485H 6-63 No A A A A A 486H 6-63 5-59 Name Constant Number Display Control Methods Description Factory Setting 0.1 to 5.0 0.2 s 0.0 to 5.0 0.3 s Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 487H 6-63 6-66 No A A A A A 488H 6-63 6-66 No A A A A A 489H 6-64 No A A A A A 48AH - No A A A A A 48BH - No A A A A A 48CH - Min. baseblock time L2-03 Sets the Inverter's minimum baseblock time in units of one second, when the Inverter is restarted after power loss ridethrough. Sets the time to approximately PwrL Base- 0.7 times the motor secondary circuit time constant. block t When an overcurrent or overvoltage occurs when starting a speed search or DC injection braking, increase the set values. Setting Range Change during Operation Voltage recovery time L2-04 PwrL V/F Ramp t Undervoltage detection level L2-05 PUV Det Level L2-06 L2-07 L2-08 Sets the time required to return the Inverter output voltage to normal voltage at the completion of a speed search, in units of one second. Sets the time required to recover from 0 V to the maximum voltage. Sets the main circuit undervoltage (UV) detection level (main circuit DC voltage) in V units. Usually setting is not necessary. Insert an AC reactor in the Inverter input side to lower the main circuit undervoltage detection level. KEB decel- Sets in seconds the time eration time required to decelerate from the speed where the deceleration at momentary power loss comKEB Fremand (KEB) is input to zeroquency speed. Momentary recovery time UV RETURN TIME Frequency reduction gain at KEB start KEB Decel Time 150 to 210 *2 0.0 to 200.0 Set in seconds the time to accelerate to the set speed after recovery from a momentary power loss. 0.0 to 25.5 Sets as a percent the about to reduce the output frequency at the beginning of deceleration at momentary power loss (KEB). Reduction = slip frequency before KEB operation × L2-08 ×2 0 to 300 *1 *1 190 V *2 0.0 s 0s *3 100 Note Attach a Backup Capacitor Unit for Momentary Power Loss if compensation for power interruptions of up to 2.0 seconds is required for 200 V/400 V Class Inverters with outputs of 0.4 to 7.5 kW. * 1. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. * 2. These are values for a 200 V Class Inverter. Value for a 400 V Class Inverter is double. * 3. If the setting is 0, the axis will accelerate to the specified speed for the specified acceleration time (C1-01 to C1-08). 5-60 User Constant Tables Stall Prevention: L3 User constants for the stall prevention function are shown in the following table. Name Constant Number Display Stall prevention selection during accel L3-01 StallP Accel Sel L3-02 Stall prevention level during accel StallP Accel Lvl L3-03 Stall prevention limit during accel StallP CHP Lvl Stall prevention selection during decel L3-04 StallP Decel Sel Control Methods Description Setting Range Factory Setting Change during Operation 0: Disabled (Acceleration as set. With a heavy load, the motor may stall.) 1: Enabled (Acceleration stopped when L3-02 level is exceeded. Acceleration starts again when the current is returned.) 2: Intelligent acceleration mode (Using the L3-02 level as a basis, acceleration is automatically adjusted. Set acceleration time is disregarded.) 0 to 2 1 Effective when L3-01 is set to 1 or 2. Set as a percentage of Inverter rated current. Usually setting is not necessary. The factory setting reduces the set values when the motor stalls. 0 to 200 Sets the lower limit for stall prevention during acceleration, as a percentage of the Inverter rated current, when operation is in the frequency range above E1-06. Usually setting is not necessary. 0 to 100 0: Disabled (Deceleration as set. If deceleration time is too short, a main circuit overvoltage may result.) 1: Enabled (Deceleration is stopped when the main circuit voltage exceeds the overvoltage level. Deceleration restarts when voltage is returned.) 2: Intelligent deceleration mode (Deceleration rate is automatically adjusted so that the Inverter can decelerate in the shortest possible time. Set deceleration time is disregarded.) 3: Enabled (with Braking Resistor Unit) When a braking option (Braking Resistor, Braking Resistor Unit, Braking Unit) is used, always set to 0 or 3. 0 to 3 *1 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A No No 48FH 4-21 6-23 150% No A A A No No 490H 4-21 6-23 50% No A A A No No 491H 4-21 6-23 1 No Q Q Q Q Q 492H 4-6 4-21 6-25 5-61 Name Constant Number Display Stall prevention selection during running L3-05 StallP Run Sel L3-06 Stall prevention level during running StallP Run Level Overvoltage inhibit selection L3-11 OV Inhibit Sel Overvoltage inhibit voltage level L3-12 OV Inhbt VoltLv1 Control Methods Description Setting Range Factory Setting Change during Operation 0: Disabled (Runs as set. With a heavy load, the motor may stall.) 1: Deceleration time 1 (the deceleration time for the stall prevention function is C1-02.) 2: Deceleration time 2 (the deceleration time for the stall prevention function is C1-04.) 0 to 2 1 Effective when L3-05 is 1 or 2. Set as a percentage of the Inverter rated current. Usually setting is not necessary. The factory setting reduces the set values when the motor stalls. 30 to 200 0: Disabled 1: Enabled Used to enable or disable the function for inhibiting main circuit overvoltages by reducing the regenerative torque limit according to the main circuit overvoltage level. If this function is enabled, when the main circuit voltage rises, operation will be performed with the regenerative torque less than the set value. Sets the main circuit voltage level for which the regenerative torque limit is restricted to 0. Usually, there is no need to change this setting. If main circuit overvoltages occur even with the overvoltage inhibit function enabled, reduce this setting. Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A No No No 493H 4-21 6-49 160% No A A No No No 494H 4-21 6-49 0 or 1 0 No No No A A A 4C7H 4-21 6-27 7-3 350 to 390 380V No No No A A A 4C8H 4-21 6-27 *2 *2 * 1. The setting range for flux vector and open-loop vector 2 controls is 0 to 2. * 2. These values are for a 200 V Class Inverter. For a 400 V Class Inverter, double the values. Reference Detection: L4 User constants for the reference detection function are shown in the following table. Name Constant Number L4-01 5-62 Display Control Methods Description Speed agree Effective when “Desired fredetection quency (ref/setting) agree 1,” level “Frequency detection 1,” or “Frequency detection 2" is set Spd Agree for a multi-function output. Frequencies to be detected are Level set in Hz units. Setting Range Factory Setting Change during Operation 0.0 to 400.0 0.0 Hz No V/f V/f with PG Open Loop Vector 1 Flux Vector A A A A Open MEMOBUS Loop Page Vec- Register tor 2 A 499H 6-50 User Constant Tables Name Control Methods Setting Range Factory Setting Change during Operation L4-02 Speed agree Effective when “Frequency detection (speed) agree 1,” “Desired frewidth quency (speed) agree 1,” or “Frequency (FOUT) detection 1,” Frequency (FOUT) detecSpd Agree tion 2 is set for a multi-function output. Width Sets the frequency detection width in Hz units. 0.0 to 20.0 2.0 Hz L4-03 Speed agree Effective when “Desired fredetection quency (speed) agree 2,” “Frelevel (+/-) quency (FOUT) detection 3,” or “Frequency (FOUT) detection 4" is set for a multi-funcSpd Agree tion output. Lvl+Frequency that should be detected is set in Hz units. -400.0 to +400.0 L4-04 Speed agree Effective when “Frequency detection (speed) agree 2,” “Desired frewidth (+/-) quency (speed) agree 2,” Frequency (FOUT) detection 3 or “Frequency detection 4" is set Spd Agree for a multi-function output. Width+Frequency detection width is set in Hz units. Constant Number L4-05 Description Display Operation when frequency reference is missing Ref Loss Sel 0: Stop (Operation follows the frequency reference.) 1: Operation at 80% speed continues. (At 80% of speed before the frequency reference was lost) Frequency reference is lost: Frequency reference dropped over 90% in 400 ms. Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 49AH 6-50 0.0 Hz No A A A A A 49BH 6-51 0.0 to 20.0 2.0 Hz No A A A A A 49CH 6-51 0 or 1 0 No A A A A A 49DH 6-71 Fault Restart: L5 User constants for restarting faults are shown in the following table. Name Description Setting Range Factory Setting Sets the number of auto restart attempts. Automatically restarts after a fault and conducts a speed search from the run frequency. 0 to 10 0 Auto restart Sets whether a fault contact operation output is activated during fault selection restart. 0: Not output (Fault contact is not activated.) Restart Sel 1: Output (Fault contact is activated.) 0 or 1 0 Display L5-01 Number of auto restart attempts Num of Restarts L5-02 Control Methods Change during Operation Constant Number Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 49EH 6-72 No A A A A A 49FH 6-72 5-63 Torque Detection: L6 User constants for the torque detection function are shown in the following table. Name Constant Number Display Overtorque/ Undertorque detection selection 1 L6-01 Torq Det 1 Sel L6-02 Overtorque/ Undertorque detection level 1 Torq Det 1 Lvl L6-03 Description Setting Range Factory Setting 0: Overtorque/undertorque detection disabled. 1: Overtorque detection only with speed agreement; operation continues after overtorque (warning). 2: Overtorque detected continuously during operation; operation continues after overtorque (warning). 3: Overtorque detection only with speed agreement; output stopped upon detection (protected operation). 4: Overtorque detected continuously during operation; output stopped upon detection (protected operation). 5: Undertorque detection only with speed agreement; operation continues after overtorque (warning). 6: Undertorque detected continuously during operation; operation continues after overtorque (warning). 7: Undertorque detection only with speed agreement; output stopped upon detection (protected operation). 8: Undertorque detected continuously during operation; output stopped upon detection (protected operation). 0 to 8 0 Open-loop vector control: Motor rated torque is set as 100%. V/f control: Inverter rated current is set as 100%. 0 to 300 0.0 to 10.0 Overtorque/ Undertorque Sets the overtorque/underdetection torque detection time in 1-sectime 1 ond units. Torq Det 1 Time 5-64 Control Methods Change during Operation Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 4A1H 6-53 150% No A A A A A 4A2H 6-53 0.1 s No A A A A A 4A3H 6-54 User Constant Tables Name Constant Number L6-04 Control Methods Description Display Overtorque/ Undertorque detection selection 2 Setting Range Factory Setting Change during Operation 0 to 8 0 0 to 300 0.0 to 10.0 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 4A4H 6-54 150% No A A A A A 4A5H 6-54 0.1 s No A A A A A 4A6H 6-54 Torq Det 2 Sel L6-05 L6-06 Multi-function output for overtorque detection 1 is output to Overtorque/ multi-function contact output Underwhen overtorque detection 1 torque NO or overtorque detection 1 detection NC is selected. Multi-function level 2 output for overtorque detection Torq Det 2 2 is output to multi-function contact output when overtorque Lvl detection 2 NO or overtorque Overtorque/ detection 2 NC is selected. Undertorque detection time 2 Torq Det 2 Time Torque Limits: L7 User constants for torque limits are shown in the following table. Constant Number Control Methods Name Description Forward drive torque L7-01 limit Setting Range Factory Setting Change during Operation 0 to 300 200% 0 to 300 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No No No A A A 4A7H 4-21 6-46 200% No No No A A A 4A8H 4-21 6-46 0 to 300 200% No No No A A A 4A9H 4-21 6-46 0 to 300 200% No No No A A A 4AA H 4-21 6-46 Torq Limit Fwd Reverse drive torque L7-02 limit Sets the torque limit value as a percentage of the motor rated torque. Four individual regions can be set. Torq Limit Rev Forward regenerative torque L7-03 limit Torq Lmt Fwd Rgn Reverse regenerative torque L7-04 limit Output torque Positive torque Reverse No. of motor rotations Regenerative state Regenerative state Forward Negative torque Torq Lmt Rev Rgn 5-65 Constant Number Control Methods Name Description Integral time setting for L7-06 torque limit Set the integral time for the torque limit. When integral control is set for the torque limit, reduce this setting to increase the change in frequency for the torque limit. Torq Limit *Normally handled with PRG: 103. Time Control method selection for torque limit durL7-07 ing acceleration and deceleration Torque Limit Sel Setting Range Factory Setting Change during Operation 5 to 10,000 200 ms 0, 1 0 Select the control method for the torque limit during acceleration and deceleration. 0: Proportional control (integral control during constant speed) 1: Integral control Normally, this constant does not need to be set. *Normally handled with PRG: 103. Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No No No A No No 4ACH 4-21 6-46 No No No A No No 4C9H 4-21 6-46 Hardware Protection: L8 User constants for hardware protection functions are shown in the following table. Name Description Setting Range Factory Setting 0: Disabled (no overheating protection) 1: Enabled (overheating protection) 0 or 1 0 L8-02 Overheat pre- Sets the detection temperature alarm level for the Inverter overheat detection pre-alarm in °C. The pre-alarm detects when OH Prethe heatsink temperature Alarm Lvl reaches the set value. 50 to 130 L8-03 Operation Sets the operation for when selection after the Inverter overheat preoverheat pre- alarm goes ON. alarm 0: Ramp to stop (Deceleration stop using Deceleration Time 1, C102.) 1: Coast to stop 2: Fast stop (Emergency stop using the deceleration OH Pretime in C1-09.) Alarm Sel 3: Continue operation (Monitor display only.) A fault will be given in setting 0 to 2 and a minor fault will be given in setting 3. 0 to 3 Constant Number L8-01 Display Protect selection for internal DB resistor (Type ERF) DB Resistor Prot 5-66 Control Methods Change during Operation Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 4ADH 6-74 95 °C*1 No A A A A A 4AEH 6-75 3 No A A A A A 4AFH 6-75 User Constant Tables Name Constant Number Description Setting Range Factory Setting 0: Disabled 1: Enabled (Detects if input current open-phase, power supply voltage imbalance or main circuit electrostatic capacitor deterioration occurs.) This fault is detected if a load is greater than approximately 80% of the maximum motor capacity. 0 or 1 0 0: Disabled 1: Enabled 2: Enabled Output open-phase is detected at less than 5% of Inverter rated current. When applied motor capacity is small for Inverter capacity, output open-phase may be detected inadvertently or open-phase may not be detected. In this case, set to 0. 0 to 2 0: Disabled 1: Enabled Cooling fan Set the ON/OFF control for control selec- the cooling fan. tion 0: ON only when Inverter is ON FAN Control 1: ON whenever power is Sel ON Display Input openphase protection selection L8-05 Ph Loss In Sel Output openphase protection selection L8-07 Ph Loss Out Sel L8-09 Ground protection selection Ground Fault Sel L8-10 L8-11 Cooling fan control delay time FAN OFF TIM L8-12 L8-15 OL2 characteristics selection at low speeds Soft CLA selection Soft CLA Sel Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 4B1H - 0 No A A A A A 4B3H - 0 or 1 1 No A A A A A 4B5H - 0 or 1 0 No A A A A A 4B6H - 0 to 300 60 s No A A A A A 4B7H - 45 to 60 45 °C No A A A A A 4B8H - 0: OL2 characteristics at low speeds disabled. 1: OL2 characteristics at low speeds enabled. 0 or 1 1 No A A A A A 4BBH - 0: Disable (gain = 0) 1: Enable 0 or 1 1 No A A A A A 4BEH - Set the time in seconds to delay turning OFF the cooling fan after the cooling fan OFF command is received. Ambient tem- Set the ambient temperature. perature If set to 60 °C, the Inverter overload protection function temp (OL2) will start 20% earlier. OL2 Chara@LSpd L8-18 Control Methods Change during Operation 5-67 Name Constant Number L8-32 *2 Display OH1 detection of Inverter’ s cooling fan OH1 Detect Sel L8-38 *3 Carrier frequency reduction selection Prtct@L-Spd L8-39 *3 L8-41 *3 * * * * L-Spd Carrier F Description Setting Range Factory Setting 0: Disabled (FAN minor fault detection) 1: Enabled (OH1 major fault detection) 0 or 1 1 0: Disabled (No carrier frequency reduction.) 1: Enabled (Carrier frequency is reduced accordingly.) 0 or 1 Sets the reduced carrier frequency. Current alarm Allows or restricts an alarm from being triggered when the relative output current rises above 150%. HC Alarm 0: Disabled. Sel 1: Enabled (alarm will be output). 0, 4 to 2.0 *5 0 or 1 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 4E2H 6-73 No A A A No No 4EFH - *1 *4 No A A A No No 4F0H - 0 No A A A A A 4F2H 6-181 1 *4 2.0 kHz The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. Applicable for G7-Series Inverters with software versions PRG:1038 or later. Applicable for G7-Series Inverters with software versions PRG:1039 or later. If a current exceeding 110% of the Inverter rated current flows through the unit, the carrier frequency will automatically decrease and electromagnetic noise will occur. * 5. The lower limits are 0.4 kHz for V/f control and 1.0 kHz for flux vector control. The upper limit is the same value as that of the factory setting for L839. 5-68 1. 2. 3. 4. Reduced carrier frequency Control Methods Change during Operation User Constant Tables N: Special Adjustments The following settings are made with the special adjustments constants (N constants): Hunting prevention, speed feedback detection control, high-slip braking, speed estimation, and feed forward control. Hunting Prevention Function: N1 User constants for hunting prevention are shown in the following table. Name Constant Number Display Hunting-prevention function selection N1-01 Hunt Prev Select Hunting-prevention gain N1-02 N1-03 *1 Hunt Prev Gain Hunting-prevention time constant Hunt Prev Time Control Methods Description Setting Range Factory Setting Change during Operation 0: Hunting-prevention function disabled 1: Hunting-prevention function enabled The hunting-prevention function suppresses hunting when the motor is operating with a light load. This function is enabled in V/ f control method only. If high response is to be given priority over vibration suppression, disable the huntingprevention function. 0 or 1 1 Set the hunting-prevention gain multiplication factor. Normally, there is no need to make this setting. Make the adjustments as follows: • If vibration occurs with light load, increase the setting. • If the motor stalls, reduce the setting. If the setting is too large, the voltage will be too suppressed and the motor may stall. 0.00 to 2.50 1.00 Set the hunting-prevention primary delay time in units of ms. 0 to 500 10 ms *2 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A No No No 580H 6-40 No A A No No No 581H 4-18 6-40 No A A No No No 582H 6-40 * 1. Applicable for G7-Series Inverters with software version PRG: 1034 and later. * 2. The factory setting depends upon the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. 5-69 Speed Feedback Protection Control Functions: N2 User constants for speed feedback protection control functions are shown in the following table. Name Constant Number Description Setting Range Factory Setting Set the internal speed feedback detection control gain using the multiplication function. Normally, there is no need to make this setting. Adjust this constant as follows: • If hunting occurs, increase the set value. • If response is low, decrease the set value. Adjust the setting by 0.05 at a time, while checking the response. 0.00 to 10.00 1.00 Set the time constant to decide the rate of change in the speed feedback detection control. 0 to 2000 Increase the setting if overvoltage (OV) failures occur at the completion of acceleration or when the load changes radically. 0 to 2000 Display Speed feedback detection control (AFR) gain N2-01 AFR Gain N2-02 Control Methods Change during Operation Speed feedback detection control (AFR) time constant Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No No No A No No 584H 4-18 6-41 50 ms No No No A No No 585H 6-41 750 ms No No No A No No 586H 6-41 AFR Time N2-03 Speed feedback detection control (AFR) time constant 2 AFR Time 2 High-slip Braking: N3 User constants for high-slip braking are shown in the following table. Name Constant Number N3-01 Display High-slip braking deceleration frequency width HSB Down Freq High-slip braking current limit N3-02 HSB Current 5-70 Control Methods Description Setting Range Factory Setting Change during Operation Sets the frequency width for deceleration during high-slip braking as a percent, taking the Maximum Frequency (E1-04) as 100%. 1 to 20 5% Sets the current limit for deceleration during high-slip braking as a percent, taking the motor rated current as 100%. The resulting limit must be 150% of the Inverter rated current or less. 100 to 200 150% Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A No No No 588H - No A A No No No 589H - User Constant Tables Name Constant Number N3-03 Description Setting Range Factory Setting Set in seconds the dwell time for the output frequency for FMIN (1.5 Hz) during V/f control. Effective only during deceleration for high-slip braking. 0.0 to 10.0 1.0 s Set the OL time when the output frequency does not change for some reason during deceleration for high-slip braking. 30 to 1200 40 s Display High-slip braking stop dwell time HSB Dwell Time N3-04 Control Methods Change during Operation High-slip braking OL time HSB OL Time Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A No No No 58AH - No A A No No No 58BH - Speed Estimation: N4 User constants for speed estimation are shown in the following table. Name Constant Number Display N4-07 Integral time of speed estimator SPD EST I Time N4-08 Proportional gain of speed estimator SPD EST P GAIN N4-10 High-speed proportional gain of speed estimator OBS Gain HSPD N4-11 N4-15 Description Low-speed regeneration stability coefficient 1 Torque adjustment gain TRQ adjust gain Setting Range Factory Setting 0.060 ms Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No No No No No A 59AH 4-20 Set the integral time of the speed estimator for PI control. 0.000 to 9.999 Set the proportional gain of the speed estimator for PI control. 0 to 1000 15 No No No No No A 59BH - Set the high-speed proportional gain of the speed estimator for PI control. 0 to 1000.0 15.0 No No No No No A 59DH 4-20 40 to 70 70 Hz No No No No No A 59EH 7-34 10-4 Increase this setting if a higher power for low-speed regeneration is required. If the setting is too large, the torque reference monitor and the actual torque accuracy may deteriorate. 0.0 to 3.0 0.3 No No No No No A 5A2H 7-34 Set the torque adjustment gain for low-speed power. 0.0 to 5.0 0.8 No No No No No A 5A4H 7-34 Speed estimator switching Set the switching frequency of high-speed/low-speed frequency operation for the speed estiSpeed mator. Change F LowSpd Rgn Coef1 N4-17 Control Methods Change during Operation 0.030 ms 5-71 Name Setting Range Factory Setting 0.90 to 1.30 1.00 20 to 70 Gradually increase this setting to improve low-speed power. If the setting is too high, the power may be reduced. Usually, there is no need to change this setting. Open MEMOBUS Loop Page Vec- Register tor 2 V/f Open Loop Vector 1 Flux Vector No No No No No A 5A5H - 50 Hz No No No No No A 5AFH 7-34 10-4 0.00 to 0.40 0.10 No No No No No A 5B4H 7-34 Increase this setting to ensure stable operation for extremely low-speed regeneration. If the setting is set to a high value, the speed will increase with the size of the regenerative load. Adjust this setting in intervals of approximately 0.2. 0.00 to 10.00 1.00 No No No No No A 5B5H 7-33 N4-32 Speed estimator gain fluc- Set the lower limit for the fluctuation frequency of the tuation speed estimator’s low-speed frequency 1 proportional gain (PI control). SpdEst Gain Set the value in Hz. Frq1 0.0 to 60.0 5.0 Hz No No No No No A 5B7H 7-33 N4-33 Speed estimator gain fluc- Set the upper limit for the fluctuation frequency of the tuation speed estimator’s low-speed frequency 2 proportional gain (PI control). SpdEst Gain Set the value in Hz. Frq2 0.0 to 60.0 20.0 Hz No No No No No A 5B8H 7-33 N4-34 Speed estimator gain fluc- Set ratio for fluctuating the speed estimator’s low-speed tuation rate proportional gain (PI control). SpdEst Gain Set the value as a percentage. Rate 0.0 to 200.0 200.0% No No No No No A 5B9H 7-33 Display N4-18 Feeder resistance adjustment gain Feeder R gain N4-28 Description Set the gain for the feeder resistance in the speed estimator. Speed estimator switching Set the switching frequency of high-speed/low-speed frequency 2 operation for the speed estiSpeed mator during deceleration. Change F 2 Torque adjustment gain 2 N4-29 TRQ adjust gain 2 Low-speed regeneration stability coefficient 2 N4-30 LowSpd Rgn Coef 2 5-72 Control Methods Change during Operation V/f with PG Constant Number User Constant Tables Feed Forward: N5 User constants for the feed forward control are shown in the following table. Name Constant Number N5-01 Description Display Feed forward control selec- Select the feed forward control. tion 0: Disabled Feedfoward 1: Enabled Sel Motor acceleration time N5-02 Control Methods 0 or 1 Factory Setting 0 *1 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No No No No A A 5B0H 4-21 6-142 No No No No A A 5B1H 4-21 6-142 No No No No A A 5B2H 4-21 6-142 Set the time required to accelerate the motor at the rated torque (T100) to the rated speed (Nr). J: GD2/4, P: Motor rated output Motor Accel Time Setting Range Change during Operation ta = 2π x J [kgm2] x Nr [min-1] [s] 60 x T100 [N x m] 0.001 to 10.000 0.178 s *2 However, T100 = N5-03 Feed forward proportional gain Feedfoward Gain P [kW] 60 × 103 [N x m] x 2π Nr [min-1] Set the proportional gain for feed forward control. Speed reference response will increase as the setting of N503 is increased. 0.00 to 100.00 1.0 * 1. When the control method is changed, the factory setting will change. The flux vector factory setting is given. * 2. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. o: Digital Operator Constants The following settings are made with the Digital Operator constants (o constants): Multi-function selections and the copy function. Monitor Select: o1 User constants for Digital Operator Displays are shown in the following table. Name Constant Number Display Monitor selection o1-01 Control Methods Description Set the number of the monitor item to be displayed in the earliest 4 monitor items. (U1) The output monitor voltage User Monitor (factory setting) can be Sel changed. Setting Range Factory Setting Change during Operation 6 Yes V/f V/f with PG Open Loop Vector 1 Flux Vector A A A A Open MEMOBUS Loop Page Vec- Register tor 2 4 to 45 A 500H - 4 to 99 5-73 Name Constant Number o1-02 Display Control Methods Description Monitor Sets the monitor item to be selection after displayed when the power is power up turned on. 1: Frequency reference 2: Output frequency Power-On 3: Output current Monitor 4: The monitor item set for o1-01 Frequency units of reference setting and monitor o1-03 Display Scaling Setting Range Factory Setting Change during Operation 1 to 4 1 0 to 39999 Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector Yes A A A A A 501H 6-148 0 No A A A A A 502H 6-148 6-166 0 or 1 0 No No No No A A 503H 6-148 0 to 5 3 Yes No No No A A 504H - Sets the units that will be set and displayed for the frequency reference and frequency monitor. 0: 0.01 Hz units 1: 0.01% units (Maximum output frequency is 100%) 2 to 39: min−1 units (Sets the motor poles.) 40 to 39999: User desired display Set the desired values for setting and display for the max. output frequency. Set 4-digit number excluding the decimal point. Set the number of digits below the decimal point to display. Example: When the max. output frequency value is 200.0, set 12000 o1-04 o1-05 Setting unit for frequency Set the setting unit for freconstants related to V/f quency reference-related constants. characteris0: Hz tics 1: min−1 V/f Display Unit LCD brightness adjustment LCD Contrast 5-74 Set a smaller value to lighten the LCD and a larger value to darken the LCD (standard: 3). User Constant Tables Multi-function Selections: o2 User constants for Digital Operator key functions are shown in the following table. Name Constant Number o2-01 Display LOCAL/ REMOTE key enable/ disable Local/ Remote Key o2-02 STOP key during control circuit terminal operation Oper STOP Key Control Methods Description Setting Range Factory Setting Change during Operation Sets the Digital Operator Local/Remote Key 0: Disabled 1: Enabled (Switches between the Digital Operator and the constant settings.) 0 or 1 1 Sets the Stop Key in the run mode. 0: Disabled (When the Run Command is issued from and external terminal, the Stop Key is disabled.) 1: Enabled (Effective even during run.) 0 or 1 V/f Open Loop Vector 1 Flux Vector No A A A A A 505H 6-148 1 No A A A A A 506H 6-149 0 to 2 0 No A A A A A 507H 6-149 User constant initial value o2-03 Clears or stores user initial values. 0: Stores/not set 1: Begins storing (Records the set constants as user initial values.) 2: All clear (Clears all recorded user initial User Defaults values) When the set constants are recorded as user initial values, 1110 will be set in A103. Open MEMOBUS Loop Page Vec- Register tor 2 V/f with PG kVA selection o2-04 Inverter Model # Do not set. 0 to FF 0*1 No A A A A A 508H - Frequency reference setting method selection When the frequency reference is set on the Digital Operator frequency reference monitor, sets whether the Enter Key is necessary. 0: Enter Key needed 1: Enter Key not needed When set to 1, the Inverter accepts the frequency reference without Enter Key operation. 0 or 1 0 No A A A A A 509H 6-149 Sets the operation when the Digital Operator is disconnected. 0: Disabled (Operation continues even if the Digital Operator is disconnected.) 1: Enabled (OPR is detected at Digital Operator disconnection. Inverter output is cut off, and fault contact is operated.) 0 or 1 0 No A A A A A 50AH - Sets the cumulative operation time in hour units. Operation time is calculated Elapsed Time from the set values. Set 0 to 65535 0 hr No A A A A A 50BH 6-149 o2-05 Operator M.O.P. Operation selection when digital operator is disconnected o2-06 Oper Detection o2-07 Cumulative operation time setting 5-75 Name Constant Number Description Setting Range Factory Setting 0: Cumulative time when the Inverter power is on. (All time while the Inverter power is on is accumulated.) 1: Cumulative Inverter run time. (Only Inverter output time is accumulated.) 0 or 1 0 Set the initial value of the fan operation time using time units. Fan ON Time The operation time accumulates from the set value. Set 0 to 65535 0: Disabled (U2 and U3 constants are on hold.) 1: Enabled (Initializes U2 and U3 constants.) o2-08 Elapsed Time Run o2-10 Fan operation time setting o2-12 Fault trace/ fault history clear function Fault Trace Init Output power monitor clear selection kWh Monitor Init o2-18 *2 Capacitor maintenance setting C MaintenanceSet Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 50CH - 0 hr No A A A A A 50EH 6-149 6-184 0 or 1 0 No A A A A A 510H - 0: Holds output power monitor. 1: Initializes output power monitor. (Returns to 0.) 0 or 1 0 No A A A A A 512H 5-81 Allows the user to set the maintenance time for the electrolytic capacitors (U161). The user can reset the accumulated operation time back to zero, or to some other desired value. 0 to 150 0% No A A A A A 51DH 6-184 Display Cumulative operation time selection o2-14 Control Methods Change during Operation * 1. The factory setting depends upon the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. * 2. Applicable for G7-Series Inverters with software versions PRG: 1039 or later. Copy Function: o3 User constants for the copy function are shown in the following table. Name Constant Number Display Copy function selection o3-01 o3-02 5-76 Copy Function Sel Read permitted selection Copy Allowable Control Methods Setting Range Factory Setting Change during Operation 0: Normal operation 1: READ (Inverter to Operator) 2: COPY (Operator to Inverter) 3: Verify (compare) 0 to 3 0 0: Read prohibited 1: Read permitted 0 or 1 0 Description Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 515H 6-151 No A A A A A 516H 6-151 User Constant Tables T: Motor Autotuning The following settings are made with the motor autotuning constants (T constants): Settings for autotuning. Name Constant Number T1-00 Control Methods Description Setting Range Factory Setting Change during Operation Set the location where the autotuned motor constants are to be stored. 1: Motor 1 2: Motor 2 1 or 2 1 Set the autotuning mode. 0: Rotational autotuning 1: Stationary autotuning 1 2: Stationary autotuning for line-to-line resistance only Tuning Mode 3: Shipping adjustment*5 Sel 4: Stationary autotuning 2*7 0 to 4 Display Motor 1/2 selection Select Motor Open MEMOBUS Loop Page Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No Yes Yes Yes Yes Yes 700H 4-14 Autotuning mode selection T1-01 T1-02 T1-03 Motor output power Mtr Rated Power Motor rated voltage Rated Voltage T1-04 Motor rated current Rated Current T1-05 T1-06 T1-07 Motor base frequency Rated Frequency Number of motor poles Number of Poles Motor base speed Rated Speed T1-08 Number of PG pulses when turning PG Pulses/ Rev T1-09 *7 Motor noload current No-Load Current 0 *1 *6 No Yes Yes Yes Yes Yes 701H 4-10 4-14 Set the output power of the motor in kilowatts. 0.00 to 650.00 0.40 kW No Yes Yes Yes Yes Yes 702H 4-14 Set the rated voltage of the motor in volts. 0.0 to 200.0 V *2 255.5*2 No No No Yes Yes Yes 703H 4-14 Set the rated current of the motor in amps. 0.32 to 6.40 *4 1.90 A No Yes Yes Yes Yes Yes 704H 4-14 Set the base frequency of the motor in hertz. 0.0 to 400.0 60.0 Hz No No No Yes Yes Yes 705H 4-14 Set the number of motor poles. 2 to 48 poles 4 poles No No No Yes Yes Yes 706H 4-14 Set the base speed of the motor in min−1. 0 to 24000 1750 min−1 No No No Yes Yes Yes 707H 4-15 Set the number of pulses per revolution for the PG being used (pulse generator or encoder) without any multiplication factor. 0 to 60000 600 No No Yes No Yes No 708H 4-15 Set the current value recorded in the motor’s test results for a motor without a load. Displayed only when Stationary autotuning 2 is selected (T1-01 = 4). 0.00 to 1.89 *8 1.20A No No No Yes Yes Yes 709H 4-15 *3 *3 *3 * 1. Set T1-02 and T1-04 when 2 is set for T1-01. Only set value 2 (2 or 3 for Control Boards ETC618046-S1033 and later) is possible for V/f control or V/ f control with PG. * 2. These are values for a 200 V Class Inverter. Values for a 400 V Class Inverter are double. * 3. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter for 0.4 kW is given. * 4. The setting range is from 10% to 200% of the Inverter rated output current. The value for a 200 V Class Inverter for 0.4 kW is given. * 5. Applicable for Control Boards ETC618046-S1033 and later. Refer to Chapter 8 Procedure for Adjusting Constants after Replacement of Control Board (Page 8-3) for the details of setting 3 (Shipping adjustment). * 6. When the control method is changed, the factory setting will change. The open-loop vector 1 control factory setting is given. * 7. Applicable for G7-Series Inverters with software versions PRG: 1039 or later. * 8. The setting range depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. The upper limit depends on the setting of E2-01. 5-77 U: Monitor Constants The following settings are made with the monitor constants (U constants): Setting constants for monitoring in drive mode. Status Monitor Constants: U1 The constants used for monitoring status are listed in the following table. Name Constant Number U1-01 U1-02 Display Frequency reference Frequency Ref Output frequency Output Freq U1-03 U1-04 U1-05 U1-06 U1-07 Output current Output Current Control method Control Method Control Methods Description V/f V/f with PG Open Loop Vector 1 Flux Vector Open MEMOBUS Loop Vec- Register tor 2 10 V: Max. frequency (-10 to 10 V possible) 0.01 Hz A A A A A 40H Monitors the output frequency.* 10 V: Max. frequency (-10 to 10 V possible) 0.01 Hz A A A A A 41H Monitors the output current. 10 V: Inverter rated output current (0 to +10 V, absolute value output) 0.01 A A A A A A 42H Checks the current control method. (Cannot be output.) - A A A A A 43H 10 V: Max. frequency (-10 to 10 V possible) 0.01 Hz No A A A A 44H 10 V: 200 VAC (400 VAC) (0 to +10 V output) 0.1 V A A A A A 45H 1V A A A A A 46H 0.1 kW A A A A A 47H 0.1% No No A A A 48H Monitors the detected Motor Speed motor speed.* Output Voltage Min. Unit Monitors/sets the frequency reference value.* Motor speed Output voltage Output Signal Level During Multi-Function Analog Output Monitors the output voltage reference value in the Inverter. DC bus voltage Monitors the main DC voltage in the Inverter. DC Bus 10 V: 400 VDC (800 VDC) (0 to +10 V output) Voltage U1-08 U1-09 Output power Output kWatts 10 V: Inverter capacity Monitors the output power (max. applicable motor (internally detected value). capacity) (-10 to 10 V possible) Torque referMonitor in internal torque ence reference value for vector Torque Ref- control. erence 10 V: Motor rated torque (-10 to 10 V possible) * The unit is set in o1-03 (frequency units of reference setting and monitor). 5-78 User Constant Tables Name Constant Number Display Control Methods Output Signal Level During Multi-Function Analog Output Open MEMOBUS Loop Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector - A A A A A 49H (Cannot be output.) - A A A A A 4AH 1: Run 1: Zero speed 1: Reverse 1: Reset signal input (Cannot be output.) 1: Speed agree 1: Inverter ready 1: Minor fault - A A A A A 4BH Description Min. Unit Input termi- Shows input ON/OFF status. nal status U1-10= 00000000 U1-10 Input Term Sts 1: FWD command (S1) is ON. 1: REV command (S2) is ON. 1: Multi input 1 (S3) is ON. 1: Multi input 2 (S4) is ON. 1: Multi input 3 (S5) is ON. 1: Multi input 4 (S6) is ON. 1: Multi input 5 (S7) is ON. 1:Multi input 6 (S8) is ON. (Cannot be output.) The ON/OFF status of the following input terminals can be checked by displaying U1-10 and pressing the Enter Key. (Press the Enter Key again to return to the original display.) U1-10= 0000 1: Multi input 7 (S9) is ON. 1: Multi input 8 (S10) is ON. 1: Multi input 9 (S11) is ON. 1: Multi input 10 (S12) is ON. Output ter- Shows output ON/OFF status. minal status U1-11= 00000000 U1-11 Output Term Sts Operation status U1-12 Int Ctl Sts 1 1: Multi-function contact output (M1-M2) is ON. 1: Multi-funtion contact output 1 (P1) is ON. 1: Multi-funtion contact output 2 (P2) is ON. 1: Multi-function contact output 3 (P3) is ON. 1: Multi-function contact output 4 (P4) is ON. Not used (always 0). 1: Error output (MA/AB-MC) is ON. Inverter operating status. U1-12= 00000000 1: Major fault 5-79 Name Constant Number U1-13 U1-14 Display Cumulative operation time Control Methods Description Output Signal Level During Multi-Function Analog Output Min. Unit V/f V/f with PG Open Loop Vector 1 Flux Vector Open MEMOBUS Loop Vec- Register tor 2 (Cannot be output.) 1 hr A A A A A 4CH Elapsed Time Monitors the total operating time of the Inverter. The initial value and the operating time/power ON time selection can be set in o2-07 and o2-08. Software No. (flash memory) (Manufacturer’s ID number) (Cannot be output.) - A A A A A 4DH Monitors the input voltage of the voltage frequency reference. An input of 10 V corresponds to 100%. 10 V: 100% (10 V) (-10 to 10 V possible) 0.1 % A A A A A 4EH Monitors the input current of the multi-function analog input. An input of 20 mA corresponds to 100%. 20 mA: 100% (4 to 20 mA) (0 to 10 V, -10 to 10 V possible) 0.1 % A A A A A 4FH Monitors the input voltage of the multi-function analog input. An input of 10 V corresponds to 100%. 10 V: 100% (10 V) (-10 to 10 V possible) 0.1 % A A A A A 050H Monitors the calculated value of the motor secondary current. The motor rated secondary current corresponds to 100%. 10 V: Motor rated secondary current) (-10 to 10 V output) 0.1 % A A A A A 51H 10 V: Motor rated secondary current) (-10 to 10 V output) 0.1 % No No A A A 52H 0.01 Hz A A A A A 53H 0.01 % No A No A A 54H 0.01 % No A No A A 55H FLASH ID U1-15 Terminal A1 input voltage Term A1 Level U1-16 Terminal A2 input current (voltage) Term A2 Level U1-17 Terminal A3 input voltage Term A3 Level U1-18 Motor secondary current (Iq) Mot SEC Current U1-19 Motor exciting current (Id) Mot EXC Current U1-20 Output frequency after softstart Monitors the output frequency after a soft start. The frequency given does not 10 V: Max. frequency include compensations, such (-10 to 10 V possible) as slip compensation. SFS Output The unit is set in o1-03. ASR input U1-21 U1-22 5-80 Monitors the calculated value of the motor excitation current. The motor rated secondary current corresponds to 100%. ASR Input Monitors the input to the speed control loop. 10 V: Max. frequency The maximum frequency cor- (-10 to 10 V possible) responds to 100%. ASR output Monitors the output from the speed control loop. ASR OutThe motor rated secondary put current corresponds to 100%. 10 V: Motor rated secondary current) (-10 to 10 V possible) User Constant Tables Name Control Methods Output Signal Level During Multi-Function Analog Output Open MEMOBUS Loop Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector 0.01 % A A A A A 57H - A A A A A 58H 10 V: 200 VAC (400 VAC) (-10 to 10 V possible) 0.1 V No No A A A 59H 10 V: 200 VAC (400 VAC) (-10 to 10 V possible) 0.1 V No No A A A 5AH - A A A A A 5BH 0.1 kWH A A A A A 5CH MWH A A A A A 5DH U1-32 ACR output of q axis Monitors the current control 10 V: 100% output value for the motor sec(-10 to 10 V possible) ACR(q) ondary current. Output 0.1 % No No A A A 5FH U1-33 ACR output of d axis Monitors the current control output value for the motor ACR(d) excitation current. Output 0.1 % No No A A A 60H - A A A A A 61H 1 No No No A No 62H Constant Number U1-24 Display PID feedback value PID Feedback DI-16H2 input status U1-25 U1-26 DI-16 Reference Description Monitors the feedback value when PID control is used. The input for the max. frequency corresponds to 100%. 10 V: Max. frequency (-10 to 10 V possible) Monitors the reference value from a DI-16H2 Digital Reference Board. (Cannot be output.) The value will be displayed in binary or BCD depending on user constant F3-01. Output voltage referMonitors the Inverter internal ence (Vq) voltage reference for motor Voltage Ref secondary current control. Min. Unit (Vq) U1-27 Output voltage referMonitors the Inverter internal ence (Vd) voltage reference for motor Voltage Ref excitation current control. (Vd) U1-28 Software No. (CPU) CPU ID U1-29 Output power lower 4 digits (Manufacturer’s CPU software (Cannot be output.) No.) Monitors the Inverter’s output power. The display is split into upper digits and lower digits in the following way. kWh Lower . kWH 4 dig U1-30 U1-29 U1-30 U1-34 U1-35 Output power upper 5 digits (Cannot be output.) Example: If the output power is 12345678.9 kWh, the display will be as follows: U1-29: 678.9 kWH kWh Upper U1-30: 12345 MWH Range: 0.0 to 32767999.9 5 dig OPE fault constant OPE Detected Zero-servo movement pulses Zero Servo Pulse 10 V: 100% (-10 to 10 V possible) Shows the first constant number where an OPE fault was detected. (Cannot be output.) Shows the number of PG pulses times 4 for the movement range when stopped at zero. 5-81 Name Constant Number U1-36 Display PID input volume PID Input U1-37 PID output volume PID Output U1-38 PID target value PID Setpoint Control Methods Description Output Signal Level During Multi-Function Analog Output Min. Unit V/f V/f with PG Open Loop Vector 1 Flux Vector Open MEMOBUS Loop Vec- Register tor 2 PID feedback volume 10 V: Max. frequency Given as maximum frequency/ (-10 to 10 V possible) 100% 0.01 % A A A A A 63H PID control output 10 V: Max. frequency Given as maximum frequency/ (-10 to 10 V possible) 100% 0.01 % A A A A A 64H PID target value Given as maximum frequency/ 100% 0.01 % A A A A A 65H (Cannot be output.) - A A A A A 66H (Cannot be output.) 1 hr A A A A A 68H Monitors the calculated value of the motor flux. 100% is dis10 V: Rated motor flux played for the rated motor flux. 0.1 % No No No No A 69H Monitors motor flux current 10 V: Rated secondary curcompensation value. 100% is rent of motor displayed for the rated second(-10 V to 10 V) ary current of the motor. 0.1 % No No No No A 6AH 10 V: Rated secondary current of motor (-10 V to 10 V) 0.01 % No No No A A 6BH 10 V: Rated secondary current of motor (-10 V to 10 V) 0.01 % No No No A A 6CH 10 V: Max. frequency MEMOBUS Shows MEMOBUS errors. communi- U1-39= 00000000 1: CRC error cations 1: Data length error error code U1-39 Transmit Err U1-40 U1-42 U1-43 Cooling fan operating Monitors the total operating time time of the cooling fan. The FAN time can be set in 02-10. Elapsed Time Estimated motor flux Mot Flux EST Motor flux current compensation Id Comp Value ASR output without filter U1-44 ASR Output w Fil U1-45 Feed forward control output FF Cout Output 5-82 Not used (always 0). 1: Parity error 1: Overrun error 1: Framing error 1: Timeout Not used (always 0). Monitors the output from the speed control loop (i.e., the primary filter input value). 100% is displayed for rated secondary current of the motor. Monitors the output from feed forward control. 100% is displayed for rated secondary current of the motor. User Constant Tables Name Constant Number U1-48 V/f Open Loop Vector 1 Flux Vector 0.01 Hz No No No No A 6FH H No No No No A 71H For maintenance purposes, this timer shows the amount of time the electrolytic capacitors (Cannot be output.) have been operating. Capacitors should be replaced when the monitor reaches 100%. 1% A A A A A 7CH Cooling fan This monitor displays the mainteamount of time the cooling fan nance (Cannot be output.) has been operating. Replace the cooling fan when the disMainteplay reads 100%. nance 1% A A A A A 7EH 0.01 A A A A A A 7CFH A A A A A 7DOH Display Stable speed for regeneration CF error code U1-61 *3 CF Error Code Electrolytic capacitor maintenance C MaintenanceFan U1-63 *3 U1-83 *3 U1-84 *3 Open MEMOBUS Loop Vec- Register tor 2 V/f with PG StableSpd @Regen U1-50 Control Methods Output Signal Level During Multi-Function Analog Output Peak hold current Current PeakHold Output frequency during peak hold Freq@ I PeakHold Description Monitors the minimum speed for which the speed will not exceed the speed reference in a 0.00 to 20.00 steady state during 100% load regeneration. Monitors the CF error code. 00: No deceleration for 3 s after Stop Command 01: Magnetic flux calculation error 02: Startup status fault 04: Speed estimator gain adjustment fault 08: Low-speed regeneration fault 10: Zero-speed fault 20: Rotation direction limit fault 0 to FFFF Displays the peak value of the current during run. “Peak Hold” refers to the moment that the peak value is saved. 10V: Inverter rated output current (-10 to 10 V absolute value output) Displays the frequency value when the output current reached its peak value. 10V: Max frequency (-10 to 10 V) Min. Unit *1 0.01 Hz *2 * 1. The minimum unit differs depending on the Inverter capacity. (0.01 A for Inverter of 0.4 kW to 7.5 kW, and 0.1 A for Inverter of 11 kW or more) * 2. The setting unit can be selected in o1-03. * 3. Applicable for G7-Series Inverters with software versions PRG: 1039 or later. 5-83 Fault Trace: U2 User constants for error tracing are shown in the following table. Name Constant Number U2-01 U2-02 U2-03 Control Methods V/f Open Loop Vector 1 Flux Vector - A A A A A 80H - A A A A A 81H The reference frequency when the previous fault occurred. 0.01 Hz A A A A A 82H The output frequency when the previous fault occurred. 0.01 Hz A A A A A 83H The output current when the previous fault occurred. 0.1 A A A A A A 84H The motor speed when the previ- (Cannot be output.) ous fault occurred. 0.01 Hz No A A A A 85H The output reference voltage when the previous fault occurred. 0.1 V A A A A A 86H 1V A A A A A 87H 0.1 kW A A A A A 88H 0.1% No No A No A 89H The contents of the current fault. Previous fault The contents of the error that occurred just prior to the current Last Fault fault. Display Current fault Current Fault Reference frequency at fault Output frequency at fault Open MEMOBUS Loop Vec- Register tor 2 V/f with PG Min. Unit Frequency Ref U2-04 Output Signal Level During Multi-Function Analog Output Description Output Freq U2-05 U2-06 Output current at fault Output Current Motor speed at fault Motor Speed U2-07 Output voltage reference at fault Output Voltage U2-08 U2-09 DC bus voltage at fault The main current DC voltage DC Bus Volt- when the previous fault occurred. age Output power at fault The output power when the previous fault occurred. Output kWatts U2-10 5-84 Torque reference at fault The reference torque when the previous fault occurred. The Torque Refer- motor rated torque corresponds to 100%. ence User Constant Tables Name Constant Number U2-11 Display Input terminal status at fault Input Term Sts U2-12 Description Output Signal Level During Multi-Function Analog Output The input terminal status when the previous fault occurred. The format is the same as for U110. Output terminal status at The output terminal status when fault the previous fault occurred. The Output Term format is the same as for U1-11. Control Methods Open MEMOBUS Loop Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector - A A A A A 8AH - A A A A A 8BH - A A A A A 8CH 1 hr A A A A A 8DH A A A A A 7E6H A A A A A 7E7H Min. Unit Sts U2-13 U2-14 Operation status at fault Inverter Status Cumulative operation time at fault The operating status when the previous fault occurred. The format is the same as for U1-12. (Cannot be output.) The operating time when the previous fault occurred. Elapsed time U2-21 *2 U2-22 *2 Peak hold current at fault Current PeakHold Peak hold output frequency at fault Freq@ I PeakHold Displays the peak hold current when the last fault occurred. Displays the frequency value at the moment the current reached its peak value when the last fault occurred. 0.01 A*1 0.01 Hz Note 1. The following errors are not included in the error trace: CPF00, 01, 02, 03, UV1, and UV2. 2. If the PUF fault is already indicated in U2- or U3-, even if the PUF fault is detected again, the fault trace is not updated. * 1. The minimum unit differs depending on the Inverter capacity. (0.01 A for Inverter of 0.4 kW to 7.5 kW, and 0.1 A for Inverter of 11 kW or more) * 2. Applicable for G7-Series Inverters with software versions PRG: 1039 or later. 5-85 Fault History: U3 User constants for the error log are shown in the following table. Name Constant Number U3-01 Display Most recent fault Last Fault U3-02 U3-03 U3-04 U3-05 U3-06 U3-07 U3-08 Second most recent fault Fault Message 2 Third most recent fault Fault Message 3 Fourth/oldest fault Fault Message 4 Control Methods Output Signal Level During Multi-Function Analog Output V/f Open Loop Vector 1 Flux Vector - A A A A A 90H The error contents of 2nd previous fault. - A A A A A 91H The error contents of 3rd previous fault. - A A A A A 92H The error contents of 4th previous fault. - A A A A A 93H 1 hr A A A A A 94H 1 hr A A A A A 95H 1 hr A A A A A 96H 1 hr A A A A A 97H The error contents of 1st previous fault. Cumulative operation time at fault The total operating time when the 1st previous fault Elapsed Time occurred. 1 (Cannot be output.) Accumulated time of second fault The total operating time when the 2nd previous fault Elapsed Time occurred. 2 Accumulated time of third fault The total operating time when the 3rd previous fault Elapsed Time occurred. 3 Accumulated time of fourth/oldest fault Elapsed Time 4 The total operating time when the 4th previous fault occurred. Note The following errors are not recorded in the error log: CPF00, 01, 02, 03, UV1, and UV2. 5-86 Open MEMOBUS -loop Vec- Register tor 2 V/f with PG Min. Unit Description User Constant Tables Factory Settings that Change with the Control Method (A1-02) The factory settings of the following user constants will change if the control method (A1-02) is changed. Name Constant Number b3-01 b3-02 b8-02 b8-03 C3-01 C3-02 C4-02 Display Speed search selection SpdSrch at Start Speed search operating current SpdSrch Current Energy-saving gain Energy Save Gain Energy-saving filter time constant Energy Save F.T Slip compensation gain Slip Comp Gain Slip compensation primary delay time Slip Comp Time Torque compensation primary delay time constant Factory Setting V/f Control V/f with PG Openloop Vector 1 Flux Vector Open Loop Vector 2 1 2 3 2 - 2 0 to 200 1% 120 - 100 - 10 0.0 to 10.0 0.1 - - 0.7 1.0 0.7 0.0 to 10.00 0.01 s - - 0.50 0.01 0.50 0.0 to 2.5 0.1 0.0 - 1.0 1.0 1.0 0 to 10000 1 ms 2000 - 200 - - 0 to 10000 1 ms 200 200 *5 *5 20 - - 0.00 to 300.00 0.01 - 0.20 - 20.00 10.00 0.000 to 10.000 0.001 s - 0.200 - 0.500 0.500 0.00 to 300.00 0.01 - 0.02 - 20.00 10.00 0.000 to 10.000 0.001 sec. - 0.050 - 0.500 0.500 0.000 to 0.500 0.001 - - - 0.004 0 to 1000 1 ms - - - 0 10 0.0 to 400.0*4 0.1 Hz 60.0 60.0 *3 *3 60.0 60.0 60.0 0.0 to 255.0 0.1 V 200.0 200.0 *3 *3 200.0 200.0 200.0 0.0 to 400.0 0.1 Hz 60.0 60.0 *3 *3 60.0 60.0 60.0 0.0 to 400.0 0.1 Hz 3.0 3.0 *3 *3 3.0 0.0 0.0 0.0 to 255.0 (0.0 to 510.0) 0.1 V 15.0 15.0 *3 *3 11.0 0.0 0.0 Setting Range Unit 0 to 3 Torq Comp Time C5-01 C5-02 C5-03 C5-04 C5-06 d5-02 ASR proportional (P) gain 1 ASR P Gain 1 ASR integral (I) time ASR I Time 1 ASR proportional (P) gain 2 ASR P Gain 2 ASR integral (I) time 2 ASR I Time 2 ASR primary delay time ASR Delay Time Torque reference delay time Torq Ref Filter E1-04 E3-02 Max. output frequency (FMAX) E1-05 E3-03 Max. voltage (VMAX) E1-06 E3-04 Base frequency (FA) Max Frequency Max Voltage Base Frequency E1-07 E3-05 Mid. output frequency (FB) E1-08 E3-06 Mid. output frequency voltage (VC)*2 Mid Frequency A Mid Voltage A 0.010 0.035 5-87 Name Constant Number Display E1-09 E3-07 Min. output frequency (FMIN) E1-10 E3-08 Min. output frequency voltage (VMIN)*2 Unit 0.0 to 400.0 0.1 Hz 0.0 to 255.0 (0.0 to 510.0) 0.1 V 0.0 to 2.0 0, 1 Min Voltage Overspeed detection delay time PG Overspd Time Feedforward control selection N5-01 1. 2. 3. 4. 5. Setting Range Min Frequency F1-09 * * * * * Factory Setting Feedfoward Sel Openloop Vector 1 Flux Vector Open Loop Vector 2 0.5 0.0 0.3 2.0 0.0 1.0 1.0 - 0.0 0.0 - - 0 1 V/f Control V/f with PG 1.5 1.5 *3 *3 9.0 9.0 *3 *3 0.1 s - 1 - The settings will be 0.05 (Flux vector)/1.00 (open-loop vector) for Inverters of 45kW or larger. The settings shown are for 200 V Class Inverters. The values will double for 400 V Class Inverters. Settings vary as shown in the following tables depending on the Inverter capacity and E1-03. The setting range for open-loop vector 2 control is 0 to 66.0 (0 to 132.0 for PRG: 103). 1000 ms for Inverters of 200 V Class 30 to 110 kW and 400 V Class 55 to 300 kW. 200 V and 400 V Class Inverters of 0.4 to 1.5 kW Constant Number Open Loop Vector Control 1 Open Loop Vector Control 2 Flux Vector Control 60.0 60.0 60.0 60.0 Factory Setting Unit E1-03 - 0 1 2 3 4 5 6 7 8 9 A B C E1-04 Hz 50.0 60.0 60.0 72.0 50.0 50.0 60.0 60.0 50.0 50.0 60.0 60.0 90.0 E1-05 * V 200.0 200.0 200.0 200.0 200.0 E1-06 Hz 50.0 60.0 50.0 60.0 E1-07 Hz 2.5 3.0 3.0 3.0 E1-08 * V 15.0 15.0 15.0 15.0 E1-09 Hz 1.3 1.5 1.5 E1-10 * V 9.0 9.0 9.0 D E 120.0 180.0 F 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 50.0 50.0 60.0 60.0 50.0 50.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 0.0 25.0 25.0 30.0 30.0 2.5 2.5 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 0.0 35.0 50.0 35.0 50.0 19.0 24.0 19.0 24.0 15.0 15.0 15.0 15.0 11.0 13.3 0.0 1.5 1.3 1.3 1.5 1.5 1.3 1.3 1.5 1.5 1.5 1.5 1.5 1.5 0.5 0.3 0.0 9.0 8.0 9.0 8.0 9.0 11.0 13.0 11.0 15.0 9.0 9.0 9.0 9.0 2.0 1.3 0.0 Open Loop Vector Control 1 Open Loop Vector Control 2 Flux Vector Control 60.0 60.0 60.0 60.0 * The setting shown are for 200 V Class Inverters. The values will double for 400 V Class Inverters. 200 V and 400 V Class Inverters of 2.2 to 45 kW Constant Number Factory Setting Unit E1-03 - 0 1 2 3 4 5 6 7 8 9 A B C E1-04 Hz 50.0 60.0 60.0 72.0 50.0 50.0 60.0 60.0 50.0 50.0 60.0 60.0 90.0 E1-05 * V 200.0 200.0 200.0 200.0 200.0 E1-06 Hz 50.0 60.0 50.0 60.0 E1-07 Hz 2.5 3.0 3.0 3.0 E1-08 * V 14.0 14.0 14.0 14.0 E1-09 Hz 1.3 1.5 1.5 E1-10 * V 7.0 7.0 7.0 E F 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 50.0 50.0 60.0 60.0 50.0 50.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 0.0 25.0 25.0 30.0 30.0 2.5 2.5 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 0.0 35.0 50.0 35.0 50.0 18.0 23.0 18.0 23.0 14.0 14.0 14.0 14.0 11.0 13.3 0.0 1.5 1.3 1.3 1.5 1.5 1.3 1.3 1.5 1.5 1.5 1.5 1.5 1.5 0.5 0.3 0.0 7.0 6.0 7.0 6.0 7.0 9.0 11.0 9.0 13.0 7.0 7.0 7.0 7.0 2.0 1.3 0.0 * The setting shown are for 200 V Class Inverters. The values will double for 400 V Class Inverters. 5-88 D 120.0 180.0 User Constant Tables 200 V Class Inverters of 55 to 110 kW and 400 V Class Inverters of 55 to 300 kW Constant Number Open Loop Vector Control 1 Open Loop Vector Control 2 Flux Vector Control 60.0 60.0 60.0 60.0 Factory Setting Unit E1-03 - 0 1 2 3 4 5 6 7 8 9 A B C E1-04 Hz 50.0 60.0 60.0 72.0 50.0 50.0 60.0 60.0 50.0 50.0 60.0 60.0 90.0 D E E1-05 * V 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 200.0 E1-06 Hz 50.0 60.0 50.0 60.0 50.0 50.0 60.0 60.0 50.0 50.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 0.0 E1-07 Hz 2.5 3.0 3.0 3.0 25.0 25.0 30.0 30.0 2.5 2.5 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 0.0 E1-08 * V 12.0 12.0 12.0 12.0 35.0 50.0 35.0 50.0 15.0 20.0 15.0 20.0 12.0 12.0 12.0 12.0 11.0 13.3 0.0 E1-09 Hz 1.3 1.5 1.5 1.5 1.3 1.3 1.5 1.5 1.3 1.3 1.5 1.5 1.5 1.5 1.5 1.5 0.5 0.3 0.0 E1-10 * V 6.0 6.0 6.0 6.0 5.0 6.0 5.0 6.0 7.0 9.0 7.0 11.0 6.0 6.0 6.0 6.0 2.0 1.3 0.0 120.0 180.0 F * The setting shown are for 200 V Class Inverters. The values will double for 400 V Class Inverters. 5-89 Factory Settings that Change with the Inverter Capacity (o2-04) The factory settings of the following user constants will change if the Inverter capacity (o2-04) is changed. 200 V Class Inverters Constant Name Unit Number Inverter Capacity E2-11 Motor Rated Capacity kW 2nd Motor Rated E4-07 Capacity o2-04 kVA selection - Factory Setting 0.4 0.75 1.5 2.2 3.7 5.5 7.5 11 15 0 1 2 3 4 5 6 7 8 b8-03 Energy-saving filter time constant s b8-04 Energy-saving coefficient - 288.20 223.70 169.40 156.80 122.90 94.75 72.69 70.44 63.13 - 6 6 6 6 6 6 6 6 6 - 4 4 4 4 4 4 4 4 4 Carrier frequency selection upper limit - 6 6 6 6 6 6 6 6 6 E2-01 (E4-01) Motor rated current A 1.90 3.30 6.20 8.50 14.00 19.60 26.60 39.7 53.0 E2-02 (E4-02) Motor rated slip Hz 2.90 2.50 2.60 2.90 2.73 1.50 1.30 1.70 1.60 E2-03 (E4-03) Motor no-load current A 1.20 1.80 2.80 3.00 4.50 5.10 8.00 11.2 15.2 E2-05 (E4-05) Motor line-to-line resistance Ω 9.842 5.156 1.997 1.601 0.771 0.399 0.288 0.230 0.138 E2-06 (E4-06) Motor leak inductance % 18.2 13.8 18.5 18.4 19.6 18.2 15.5 19.5 17.2 E2-10 Motor iron loss for torque compensation W 14 26 53 77 112 172 262 245 272 L2-02 Momentary power loss ridethru time s 0.1 0.2 0.3 0.5 1.0 1.0 1.0 2.0 2.0 L2-03 Min. baseblock (BB) time s 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 L2-04 Voltage recovery time s 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.6 L8-02 Overheat pre-alarm level °C 95 95 100 95 95 95 95 90 100 L8-39 Reduced carrier frequency kHz 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 N1-03 Hunting-prevention time constant ms 10 10 10 10 10 10 10 10 10 N5-02 Motor acceleration time s 0.178 0.142 0.166 0.145 0.154 0.168 0.175 0.265 0.244 C6-02 C6-11 Carrier frequency selection*1 Carrier frequency selection for open-loop vector 2 con- 0.50 (Open-loop vector control) trol*2 - 5-90 User Constant Tables Constant Name Unit Number Inverter Capacity E2-11 Motor Rated Capacity kW 2nd Motor Rated E4-07 Capacity o2-04 kVA selection - Factory Setting 18.5 22 30 37 45 55 75 90 110 9 A B C D E F 10 11 b8-03 Energy-saving filter time constant s b8-04 Energy-saving coefficient - 57.87 51.79 46.27 38.16 35.78 31.35 23.10 20.65 18.12 C6-02 Carrier frequency selection - 6 4 4 4 4 4 4 1 1 C6-11 Carrier frequency selection for open-loop vector 2 con- - 4 4 2 2 2 2 2 1 1 Carrier frequency selection upper limit - 6 6 4 4 4 4 4 1 1 E2-01 (E4-01) Motor rated current A 65.8 77.2 105.0 131.0 160.0 190.0 260.0 260.0 260.0 E2-02 (E4-02) Motor rated slip Hz 1.67 1.70 1.80 1.33 1.60 1.43 1.39 1.39 1.39 E2-03 (E4-03) Motor no-load current A 15.7 18.5 21.9 38.2 44.0 45.6 72.0 72.0 72.0 E2-05 (E4-05) Motor line-to-line resistance Ω 0.101 0.079 0.064 0.039 0.030 0.022 0.023 0.023 0.023 E2-06 (E4-06) Motor leak inductance % 20.1 19.5 20.8 18.8 20.2 20.5 20.0 20.0 20.0 E2-10 Motor iron loss for torque compensation W 505 538 699 823 852 960 1200 1200 1200 L2-02 Momentary power loss ridethru time s 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 L2-03 Min. baseblock (BB) time s 1.0 1.1 1.1 1.2 1.2 1.3 1.5 1.7 1.7 L2-04 Voltage recovery time s 0.6 0.6 0.6 0.6 1.0 1.0 1.0 1.0 1.0 L8-02 Overheat pre-alarm level °C 90 90 95 100 100 110 100 110 110 L8-39 Reduced carrier frequency kHz 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 N1-03 Hunting-prevention time constant ms 10 10 10 10 10 10 10 100 100 N5-02 Motor acceleration time s 0.317 0.355 0.323 0.320 0.387 0.317 0.533 0.592 0.646 0.50 (Open-loop vector control) 2.00 (Open-loop vector control) trol*2 - Note Attach a Momentary Power Interruption Compensation Unit if compensation for power interruptions of up to 2.0 seconds is required for 200 V Class Inverters with outputs of 0.4 to 7.5 kW. * 1. The initial settings for C6-02 are as follows: 0: Low noise PWM, 1: 2.0 kHz, 2: 5.0 kHz, 3: 8.0 kHz, 4: 10.0 kHz, 5: 12.5 kHz, and 6: 15.0 kHz. If the carrier frequency is set higher than the factory setting for Inverters with outputs of 5.5 kW or more, the Inverter rated current will need to be reduced. * 2. The initial settings for C6-11 are as follows: 1: 2.0 kHz, 2: 4.0 kHz, 3: 6.0 kHz, 4: 8.0 kHz. 5-91 400 V Class Inverters Constant Number E2-11 E4-07 o2-04 Name Inverter Capacity Motor Rated Capacity 2nd Motor Rated Capacity kVA selection Unit Factory Setting kW 0.4 0.75 1.5 2.2 3.7 4.0 5.5 7.5 11 15 - 20 21 22 23 24 25 26 27 28 29 b8-03 Energy-saving filter time constant s b8-04 Energy-saving coefficient - 576.40 447.40 338.80 313.60 - 3 3 3 3 3 3 3 3 3 3 - 4 4 4 4 4 4 4 4 4 4 Carrier frequency selection upper limit - 3 3 3 3 3 3 3 3 3 3 E2-01 (E4-01) Motor rated current A 1.00 1.60 3.10 4.20 7.00 7.00 9.80 13.30 19.9 26.5 E2-02 (E4-02) Motor rated slip Hz 2.90 2.60 2.50 3.00 2.70 2.70 1.50 1.30 1.70 1.60 E2-03 (E4-03) Motor no-load current A 0.60 0.80 1.40 1.50 2.30 2.30 2.60 4.00 5.6 7.6 E2-05 (E4-05) Motor line-to-line resistance Ω 6.495 3.333 3.333 1.595 1.152 0.922 0.550 E2-06 (E4-06) Motor leak inductance % 18.2 14.3 18.3 18.7 19.3 19.3 18.2 15.5 19.6 17.2 E2-10 Motor iron loss for torque compensation W 14 26 53 77 130 130 193 263 385 440 L2-02 Momentary power loss ridethru time s 0.1 0.2 0.3 0.5 0.5 0.8 0.8 1.0 2.0 2.0 L2-03 Min. baseblock (BB) time s 0.2 0.3 0.4 0.5 0.6 0.6 0.7 0.8 0.9 1.0 L2-04 Voltage recovery time s 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.6 L8-02 Overheat pre-alarm level °C 95 95 95 95 95 95 95 90 95 95 L8-39 Reduced carrier frequency kHz 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 N1-03 Hunting-prevention time constant ms 10 10 10 10 10 10 10 10 10 10 N5-02 Motor acceleration time s 0.178 0.142 0.166 0.145 0.154 0.154 0.168 0.175 0.265 0.244 C6-02 C6-11 Carrier frequency selection*1 Carrier frequency selection for open-loop vector 0.50 (Open-loop vector control) 245.80 236.44 189.50 145.38 140.88 126.26 2 control*2 - 5-92 38.198 22.459 10.100 User Constant Tables Constant Number E2-11 E4-07 o2-04 Name Inverter Capacity Motor Rated Capacity 2nd Motor Rated Capacity kVA selection Unit Factory Setting kW 18.5 22 30 37 45 55 75 90 110 132 160 185 220 300 - 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 0.50 (Open-loop vector control) b8-03 Energy-saving filter time constant s b8-04 Energy-saving coefficient - 115.74 103.58 92.54 76.32 71.56 67.20 46.20 38.91 36.23 32.79 30.13 30.57 27.13 21.76 - 3 3 3 3 3 2 2 F F 1 1 1*1 1*1 1 - 4 4 4 4 4 2 2 1 1 1 1 1 1 1 C6-02 C6-11 Carrier frequency selection*1 Carrier frequency selection for open- 2.00 (Open-loop vector control) loop vector 2 control*2 - Carrier frequency selection upper limit - 3 3 3 3 3 2 2 3*1 3*1 1 1 1 1 1 E2-01 (E4-01) Motor rated current A 32.9 38.6 52.3 65.6 79.7 95.0 130.0 156.0 190.0 223.0 270.0 310.0 370.0 500.0 E2-02 (E4-02) Motor rated slip Hz 1.67 1.70 1.80 1.33 1.60 1.46 1.39 1.40 1.40 1.38 1.35 1.30 1.30 1.25 E2-03 (E4-03) Motor no-load current A 7.8 9.2 10.9 19.1 22.0 24.0 36.0 40.0 49.0 58.0 70.0 81.0 96.0 130.0 E2-05 (E4-05) Motor line-to-line resistance Ω 0.403 0.316 0.269 0.155 0.122 0.088 0.092 0.056 0.046 0.035 0.029 0.025 0.020 0.014 E2-06 (E4-06) Motor leak inductance % 20.1 23.5 20.7 18.8 19.9 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 E2-10 Motor iron loss for torque compensation W 508 586 750 925 1125 1260 1600 1760 2150 2350 2850 3200 3700 4700 L2-02 Momentary power loss ridethru time s 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 L2-03 Min. baseblock (BB) time s 1.0 1.1 1.1 1.2 1.2 1.3 1.5 1.7 1.7 1.8 1.9 2.0 2.1 2.1 L2-04 Voltage recovery time s 0.6 0.6 0.6 0.6 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 L8-02 Overheat pre-alarm level °C 95 95 95 95 95 100 105 105 120 110 115 100 110 115 L8-39 Reduced carrier frequency kHz 2.0 2.0 2.0 2.0 2.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 N1-03 Hunting-prevention time constant ms 10 10 10 10 10 30 30 30 30 30 30 100 100 100 N5-02 Motor acceleration time s 0.317 0.355 0.323 0.320 0.387 0.317 0.533 0.592 0.646 0.673 0.777 0.864 0.910 1.392 Note Attach a Momentary Power Interruption Compensation Unit if compensation for power interruptions of up to 2.0 seconds is required for 400 V Class Inverters with outputs of 0.4 to 7.5 kW. * 1. The initial settings for C6-02 are as follows: 1: 2.0 kHz, 2: 5.0 kHz, 3: 8.0 kHz, 4: 10.0 kHz, 5: 12.5 kHz, 6: 15.0 kHz, and F: optional setting (initial value for Inverters of 90 or 110 kW: 3.0 kHz). * 2. The initial settings for C6-11 are as follows: 1: 2.0 kHz, 2: 4.0 kHz, 3: 6.0 kHz, 4: 8.0 kHz. 5-93 6 Constant Settings by Function Frequency Reference ..................................................6-2 Run Command...........................................................6-10 Stopping Methods ......................................................6-12 Acceleration and Deceleration Characteristics ..........6-18 Adjusting Frequency References...............................6-28 Speed Limit (Frequency Reference Limit Function)...6-34 Improved Operating Efficiency...................................6-36 Machine Protection ....................................................6-42 Continuing Operation.................................................6-63 Inverter Protection .....................................................6-74 Input Terminal Functions............................................6-76 Output Terminal Functions......................................... 6-86 Monitor Constants......................................................6-88 Individual Functions ...................................................6-92 Digital Operator Functions ....................................... 6-148 Options ....................................................................6-158 Using Inverters for Elevating Machines ...................6-170 Current Alarm Function............................................ 6-181 Peak Hold Current Monitoring Function...................6-182 Maintenance Timer Display Function.......................6-183 Frequency Reference This section explains how to input the frequency reference. Selecting the Frequency Reference Source Set constant b1-01 to select the frequency reference source. Related Constants Name Constant Number Display Reference selection b1-01 H6-01 Reference Source Pulse train input function selection Pulse Input Sel H6-02 Pulse train input scaling Control Methods Setting Range Factory Setting Change during Operation Set the frequency reference input method. 0: Digital Operator 1: Control circuit terminal (analog input) 2: MEMOBUS communications 3: Option board 4: Pulse train input 0 to 4 1 0: Frequency reference 1: PID feedback value 2: PID target value 0 to 2 1000 to 32000 Description Set the number of pulses in hertz, taking the reference to be 100%. PI Scaling V/f Openloop Vector 1 Flux Vector No Q Q Q Q Q 180H 0 No A A A A A 42CH 1440 Hz Yes A A A A A 42DH Input the Reference Frequency from the Digital Operator When b1-01 is set to 0, you can input the reference frequency from the Digital Operator. Input the reference frequency from the Digital Operator's reference frequency setting display. For details on setting the reference frequency, refer to Chapter 3 Digital Operator and Modes. -DRIVE-DRIVE- Rdy Frequency RefRef Frequency U1-01= 0 0 0.0 0Hz U1-01= 0 0 0.0 0Hz (0.00 60.00) "0.00Hz" Fig 6.1 Frequency Setting Display 6-2 Open MEMOBUS Loop RegisVecter tor 2 V/f with PG Frequency Reference Inputting the Frequency Reference Using Control Circuit Terminal (Analog Setting) When b1-01 is set to 1, you can input the frequency reference from control circuit terminal A1 (voltage input), or control circuit terminal A2 (voltage or current input). Inputting Master Speed Frequency Reference Only (Voltage Input) When inputting a voltage for the master speed frequency reference, input the voltage to control circuit terminal A1. Inverter +V Power supply: 15 V, 20 mA A1 Master speed frequency reference (voltage input) A2 Master speed frequency reference (current input) A3 Auxiliary speed frequency reference 1 AC Analog common 2 kΩ Fig 6.2 Voltage Input for Master Speed Frequency Reference Inputting Master Speed Frequency Reference Only (Current Input) When inputting a current for the master speed frequency reference, input the current to control circuit terminal A2, input 0 V to terminal A1, set H3-08 (Multi-function analog input terminal A2 signal level selection) to 2 (current input), and set H3-09 (Multi-function analog input terminal A2 function selection) to 0 (add to terminal A1). Inverter 4 to 20-mA input +V Power supply: 15 V, 20 mA Master speed frequency A1 reference (voltage input) A2 Master speed frequency reference (current input) A3 Auxiliary speed frequency reference 1 AC Analog common 1 2 V I DIP switch S1 Fig 6.3 Current Input for Master Speed Frequency Reference Turn ON pin 2 of DIP switch S1 (toward I), the voltage/current switch, when inputting a current to terminal A2. Turn OFF pin 2 of DIP switch S1 (toward V), the voltage/current switch, when inputting a voltage to terminal A2. Set H3-08 to the correct setting for the type of input signal being used. IMPORTANT Switch between 2 Step Speeds: Master/Auxiliary Speeds When switching between the master and auxiliary speeds, connect the master speed frequency reference to control circuit terminal A1 or A2 and connect the auxiliary speed frequency reference to terminal A3. The reference on terminal A1 or A2 will be used for the Inverter frequency reference when the multi-function input allocated to multi-speed command 1 is OFF and the reference on terminal A3 will be used when it is ON. 6-3 When switching between the master and auxiliary speeds, set H3-05 (Multi-function analog input terminal A3) to 2 (auxiliary frequency reference, 2nd step analog) and set on of the multi-function input terminals to multi-step speed reference 1. When inputting a current to terminal A2 for the master speed frequency reference, set H3-08 (Multi-function analog input terminal A2 signal level selection) to 2 (current input), and set H3-09 (Multi-function analog input terminal A2 function selection) to 0 (add to terminal A1). Inverter S5 Multi-step speed reference 1 +V Power supply: 15 V, 20 mA Master speed A1 frequency reference (voltage input) 2 kΩ 4 to 20 mA 2 kΩ Master speed A2 frequency reference (current input) A3 Auxiliary speed frequency reference 1 AC Analog common Fig 6.4 Switching between Master and Auxiliary Frequencies Setting Frequency Reference Using Pulse Train Signals When b1-01 is set to 4, the pulse train input to control circuit terminal RP is used as the frequency reference. Set H6-01 (Pulse Train Input Function Selection) to 0 (frequency reference), and then set the 100% reference pulse frequency to H6-02 (Pulse Train Input Scaling). Inverter Pulse Input Specifications Low level voltage 0.0 to 0.8 V High level voltage 3.5 to 13.2 V Heavy duty 30 to 70% Pulse frequency 0 to 32 kHz 32 kHz max. 3.5 to 13.2 V Pulse input RP(Pulse train input terminal) AC (Analog common) Fig 6.5 Frequency Reference Using Pulse Train Input 6-4 Frequency Reference Using Multi-Step Speed Operation With Varispeed-G7 series Inverters, you can change the speed to a maximum of 17 steps, using 16 frequency references, and one jog frequency reference. The following example of a multi-function input terminal function shows a 9-step operation using multi-step references 1 to 3 and jog frequency selection functions. Related Constants To switch frequency references, set multi-step speed references 1 to 3 and the jog reference selection in the multi-function contact inputs. Setting examples are shown below. Multi-function Contact Inputs (H1-01 to H1-10) Terminal Constant Number Set Value (Factory Setting) S5 H1-03 3 Multi-step speed reference 1 (Also used for master speed/auxiliary speed switching when multi-function analog input H3-05 is set to 2 (auxiliary frequency reference 1).) S6 H1-04 4 Multi-step speed reference 2 [Also used for auxiliary frequency reference 2 when multifunction analog input H3-09 is set to 3 (auxiliary frequency reference 2).] S9 H1-07 5 Multi-step speed reference 3 S7 H1-05 6 Jog frequency selection (given priority over multi-step speed reference) Details Combination of Multi-Function References and Multi-Function Contact Inputs You can change the selected frequency reference by combining the ON/OFF status of S5 to S9 (multi-function contact input terminals) to set multi-step speed references 1 to 3 and the jog frequency selection. The following table shows the possible combinations. TerminalS5 TerminalS6 TerminalS9 TerminalS7 Speed Multi-step Speed Reference 1 Multi-step Speed Reference 2 Multi-step Speed Reference 3 Jog Frequency Selection 1 OFF OFF OFF OFF Frequency reference 1 d1-01, master speed frequency 2 ON OFF OFF OFF Frequency reference 2 d1-02, auxiliary frequency 1 3 OFF ON OFF OFF Frequency reference 3 d1-03, auxiliary frequency 2 4 ON ON OFF OFF Frequency reference 4 d1-04 5 OFF OFF ON OFF Frequency reference 5 d1-05 6 ON OFF ON OFF Frequency reference 6 d1-06 7 OFF ON ON OFF Frequency reference 7 d1-07 8 ON ON ON OFF Frequency reference 8 d1-08 - ON* Jog frequency d1-17 9 - - Selected Frequency * Terminal S7's jog frequency selection is given priority over multi-step speed references. 6-5 Setting Precautions Refer to the following to set step 1 to step 3 to analog inputs. • Step 1 When setting terminal A1's analog input to step 1, set b1-01 to 1, and when setting d1-01 (Frequency Reference 1) to step 1, set b1-01 to 0. • Step 2 When setting terminal A3's analog input to step 2, set H3-05 to 2 (auxiliary frequency reference 1). When setting d1-02 (Frequency Reference 2) to step 2, set H3-05 to 1F (Analog input not used). • Step 3 When setting terminal A2's analog input to step 3, set H3-09 to 3 (auxiliary frequency reference 2). When setting d1-03(Frequency Reference 3) to step 3, set H3-05 to 1F (Analog input not used). When inputting 0 to 10 V to terminal A2’s analog input, set H3-08 to 0, and turn OFF pin 2 to DIP switch S1 on the control circuit terminal board. (Refer to page 2-26.) Connection Example and Time Chart The following diagram shows a time chart and control circuit terminal connection example during a 9-step operation. Inverter S1 Forward/stop S2 Reverse/stop S3 External fault S4 Fault reset S5 Multi-step speed reference 1 S6 Multi-step speed reference 2 S9 Multi-step speed reference 3 S7 Jog frequency SC Sequence common +V Frequency setting power (+15 V) A1 Master speed referennce (0 to 10 V) [Master speed frequency (b1-01=1)] A2 Master speed referennce (4 to 20 mA) [Auxiliary speed frequency1 (H3-09=2)] A3 Auxiliary speed frequency (0 to 10 V) [Auxiliary speed frequency 2 (H3-05=3)] AC Analog common 0 V Fig 6.6 Control Circuit Terminal During 9-step Operation 6-6 Frequency Reference Frequency reference 8 Frequency reference 7 Frequency reference 6 Frequency reference 5 Frequency reference Frequency reference 4 Frequency reference 3: Frequency ref- Auxiliary erence 2: Auxil- speed frequency 2 iary speed frequency 1 Frequency reference 1: Master speed frequency Jog frequency Forward/stop Multi-step speed reference 1 Multi-step speed reference 2 Multi-step speed reference 3 Jog frequency selection Fig 6.7 Multi-step speed reference/Jog Frequency Selection Time Chart 6-7 6-8 6GTOKPCN A3 6GTOKPCN A2 6GTOKPCN A1 Ch3 Ch2 Ch1 =1 =0 =1 =0 F2-01 =1 =0 1/10 X + + 3 2 1 C B A =1 =0 F2-01 PID feedback PID target value Frequency baias 2 Motor temperature input Yes Positive toraue limit 0B 0C 0D 0E 10 1F 15 14 13 12 11 09 08 07 06 No Negative torque limit No Regenerative torque No limit Torque refrence/torque No limit at speed control Torque compensation No Positive/negative torque No limit Analog input not used. Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes No Yes Yes Yes 100%/10 V 100%/10 V 100%/10 V Yes Yes 100%/10 V Yes ±100%/±10 V Yes ±100%/±10 V Yes 100%/10 V Yes 100%/10 V Yes 100%/10 V Yes ±100%/±10 V Yes ±100%/±10 V Yes ±100%/±10 V Yes ±100%/±10 V Yes 100%/10 V Yes 100%/10 V No Yes 100%/10 V No Yes 100%/1 V No Yes ±100%/±10 V Yes ±100%/±10 V Yes 100%/10 V Yes ±100%/±10 V Input Level Remote d2-03 Master frequency lower limit Option Frequency reference 16 (d1-16) Frequency reference 15 (d1-15) Frequency reference 14 (d1-14) Frequency reference 13 (d1-13) Frequency reference 12 (d1-12) Frequency reference 11 (d1-11) Frequency reference 10 (d1-10) Frequency reference 9 (d1-09) Frequency reference 8 (d1-08) (d1-07) Frequency !reference ! ! ! 7 Frequency reference 6 (d1-06) Frequency reference 5 (d1-05) Frequency reference 4 (d1-04) Multi-function Frequency analog input is invalid. reference 1 When 2nd speed (d1-01) analog is selected Multi-function Frequency analog input is invalid. reference 2 When 3rd speed (d1-02) analog is selected Frequency Multi-function analog input is invalid. reference 3 (d1-03) Local Inverter Fig 6.8 Varispeed G7 Function Block Yes No No No No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes V/f Open Flux with Loop VecPG Vector tor No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes V/f 0A Auxiliary frequency reference 1 (2nd step analog) Auxiliary frequency reference 2 (3rd step analog) Frequency gain Add to terminal A1 Function =0 d1-01 =0 =1 =2 =3 =4 H3-05 (Terminal A3) function H3-09 (Terminal A2) function L4-05 Memobus communication =0 Voltage bias Accel/decel change (reduction coefficient) DC injection braking current Overtorque/undertorque detection level Stall prevention level during run Frequency reference lower limit level Jump frequency 05 04 03 02 01 00 L4-05 Process when frequency =1 refrence is lost. Pulse train input Process when frequency refrence is =1 lost. Setting Value 0V 10V H3-02 H3-03 AI input㧔See fig6.11㧕 1/10 + + Note: If A1-14B is not mounted, the same operation as when F2-01=1 will be performed regardless of the F2-01 setting. A/D ±11 bits A/D ±11 bits A/D ±11 bits A/D ±13 bits A/D ±13 bits A/D ±13 bits A1-14B C option board other than A1-14B B1-01 = 15 = 14 = 13 = 12 = 11 = 10 =9 =8 =7 =6 =5 =4 =3 =2 =1 =0 Frequency reference When FJOG, RJOG (Jog frequency command) of multi-function contact input is input. Jog frequency command (d1-17㧕 Muluti-step speed reference Varispeed G7 Function Block The following diagram shows the function block diagram of Varispeed G7. Frequency Reference * * Primary delay filter * 8 # 8 * * * * Primary delay filter * 8 $ ≠ 8 * * 2 is current input. * * * Primary delay filter % * 8 8 * ≠ * The same value can not be set in H3-05 and H3-09. Fig 6.9 AI Input Detailed Diagram 6-9 Run Command This section explains input methods for the Run Command. Selecting the Run Command Source Set constant b1-02 to select the source for the Run Command. Related Constants Name Constant Number b1-02 Display Operation method selection Run Source Control Methods Description Setting Range Factory Setting Change during Operation Set the Run Command input method 0: Digital Operator 1: Control circuit terminal (sequence input) 2: MEMOBUS communications 3: Option board 0 to 3 1 No V/f V/f with PG Openloop Vector 1 Flux Vector Q Q Q Q Open MEMOBUS Loop RegisVecter tor 2 Q 181H Performing Operations Using a Digital Operator When b1-02 is set to 0, you can perform Inverter operations using the Digital Operator keys (RUN, STOP, JOG, and FWD/REV). For details on the Digital Operator, refer to Chapter 3 Digital Operator and Modes. Performing Operations Using Control Circuit Terminals When b1-02 is set to 1, you can perform Inverter operations using the control circuit terminals. Performing Operations Using a 2-wire Sequence The factory setting is set to a 2-wire sequence. When control circuit terminal S1 is set to ON, forward operation will be performed, and when S1 is turned OFF, the Inverter will stop. In the same way, when control circuit terminal S2 is set to ON, reverse operation will be performed, and when S2 is turned OFF, the Inverter will stop. Forward/stop Inverter Reverse/stop Sequence common Fig 6.10 2-wire Sequence Wiring Example 6-10 Run Command Performing Operations Using a 3-wire Sequence When any constant from H1-01 to H1-10 (multi-function contact input terminals S3 to S12) is set to 0, terminals S1 and S2 are used for a 3-wire sequence, and the multi-function input terminal that has been set functions as a Forward/Reverse Run Command terminal. When the Inverter is initialized for 3-wire sequence control with A1-03, multi-function input 3 becomes the input terminal for the Forward/Reverse Run Command. Stop switch (NC contact) Operation switch (NO contact) Run Command (operates when ON) Stop Command (stopped when ON) Forward/Reverse Command (multi-function input) Sequence input common Fig 6.11 3-wire Sequence Wiring Example 50 ms min. Can be either ON or OFF Run Command OFF (stopped) Stop Command Forward/Reverse Command OFF (forward) ON (reverse) Motor speed Stop Forward Reverse Stop Forward Fig 6.12 Three-wire Sequence Time Chart INFO 1. Use a sequence that turns ON terminal S1 for 50 ms or longer for the Run Command. This will make the Run Command self-holding in the Inverter. 2. When the 3-wire sequence is set, do not make the wiring for the control circuit unless the multi-function input terminal constant is set. Failure to observe this warning may result in injury. 6-11 Stopping Methods This section explains methods of stopping the Inverter. Selecting the Stopping Method when a Stop Command is Sent There are four methods of stopping the Inverter when a Stop Command is sent: • Deceleration to stop • Coast to stop • DC braking stop • Coast to stop with timer Set constant b1-03 to select the Inverter stopping method. A DC braking stop and coasting to a stop with a timer cannot be set for flux vector control. Related Constants Name Constant Number Display Stopping method selection b1-03 Stopping Method Operation selection for setting E1-09 or less b1-05 Zero-Speed Oper b2-01 Zero-speed level (DC injection braking starting frequency) DCInj Start Freq b2-02 DC injection braking current DCInj Current 6-12 Control Methods Description Setting Range Select stopping method when Stop Command is sent. 0: Deceleration to stop 1: Coast to stop 2: DC injection braking stop (Stops 0 to 3* faster than coast to stop, no regenerative operation.) 3: Coast to stop with timer (Run Commands are disregarded during deceleration.) Factory Setting Change during Operation 0 Open MEMOBUS Loop RegisVecter tor 2 V/f V/f with PG Openloop Vector 1 Flux Vector No Q Q Q Q Q 182H Used to set the method of operation when the frequency reference input is less than the minimum output frequency (E1-09). 0: Run at frequency reference (E1-09 not effective). 1: STOP (Frequencies below E1-09 in the coast to stop state.) 2: Run at min. frequency. (E1-09) 3: Run at zero-speed (Frequencies below E1-09 are zero) 0 to 3 0 No No No No A No 184H Used to set the frequency which starts DC injection braking in units of Hz when deceleration to stop is selected. When b2-01 is less than E1-09, E1-09 becomes the DC injection braking starting frequency. 0.0 to 10.0 0.5 Hz No A A A A A 189H Sets the DC injection braking current as a percentage of the Inverter rated current. 0 to 100 50% No A A A No No 18AH Stopping Methods Name Constant Number b2-03 b2-04 Control Methods Description Display DC injection braking time at start Used to set the time to perform DC injection braking at start in units of 1 second. Used to stop coasting motor and restart it. When the set value is 0, DC DCInj injection braking at start is not perTime@Start formed. DC injection braking time at stop Used to set the time to perform DC injection braking at stop in units of 1 second. Used to prevent coasting after the Stop Command is input. When the set DCInj value is 0.00, DC injection braking at Time@Stop stop is not performed. Setting Range Factory Setting Change during Operation 0.00 to 10.00 0.00 s 0.00 to 10.00 0.50 s Open MEMOBUS Loop RegisVecter tor 2 V/f V/f with PG Openloop Vector 1 Flux Vector No A A A A A 18BH No A A A A A 18CH * 0 or 1 for flux vector control and open-loop vector 2 control. Deceleration to Stop If the Stop Command is input (i.e., the Run Command is turned OFF) when b1-03 is set to 0, the motor decelerates to a stop according to the deceleration time that has been set. (Factory setting: C1-02 (Deceleration Time 1)) If the output frequency when decelerating to a stop falls below b2-01, the DC injection brake will be applied using the DC current set in b2-02 only for the time set in b2-04. For deceleration time settings, refer to page 6-18 Setting Acceleration and Deceleration Times. Run command ON OFF Output frequency Decelerates to stop at deceleration time DC injection brake DC injection brake time when stopping (b2-04) Fig 6.13 Deceleration to Stop 6-13 The operation after stopping depends on the setting of b1-05 when flux vector control is selected (A1-02 = 3). Run Command OFF ON OFF Frequency reference via analog input E1-09 0 b1-05=0 (frequency reference) Run Command turns OFF and zero-speed control start when motor speed drops to b2-01. Zero speed control Injection brake time at start Baseblock b2-03 b1-05=1 (Coast) b2-04 Injection brake time at start Baseblock Zero speed control b2-03 b2-04 b1-05=2 (Run on E1-09) Injection brake time at start Baseblock b1-05=3 (Zero-speed) Baseblock Frequency reference drops to less than E1-09 and zero-speed control starts when motor speed drops to b2-01. Baseblock Run Command turns OFF and zero-speed control start when motor speed drops to b2-01. Zero speed control Baseblock b2-04 Run Command turns OFF and zero-speed control start when motor speed drops to b2-01. Zero speed control b2-03 Injection brake time at start Baseblock b2-03 b2-04 Baseblock Fig 6.14 Deceleration to Stop (for Flux Vector Control) Setting Precautions • When using flux vector control, the zero-speed control starts when motor speed drops to b2-01 during deceleration. Also, the setting b2-01 < E1-09 is possible. • The current level during injection brake time at start is the value of E2-03 (motor no-load current). Accord- ingly, b2-02 is invalid in flux vector control. Coast to Stop If the Stop Command is input (i.e., the Run Command is turned OFF) when b1-03 is set to 1, the Inverter output voltage is interrupted. The motor coasts to a stop at the deceleration rate that counterbalances damage to the machine and inertia including the load. Run Command ON OFF Output frequency Inverter output freqeuencty interrupted. Fig 6.15 Coast to Stop 6-14 Stopping Methods After the Stop Command is input, Run Commands are ignored until the Minimum Baseblock Time (L2-03) has elapsed. INFO DC Braking Stop If the Stop Command is input (i.e., the Run Command is turned OFF) when b1-03 is set to 2, a wait is made for the time set in L2-03 (Minimum Baseblock (BB) Time) and then the DC injection brake current set in b202 is sent to the motor to apply a DC injection brake to stop the motor. The DC injection brake time is determined by the set value in b2-04 and the output frequency when the Stop Command is input. DC injection brake time Run Command ON OFF b2-04 10 Output frequency Inverter output voltage interrupted DC injection brake b2-04 Minimum baseblock time (L2-03) DC injection brake time 10 Output frequency at Stop Command input 100% (maximum output frequency) Fig 6.16 DC Injection Braking (DB) Stop Lengthen the Minimum Baseblock Time (L2-03) when an overcurrent (OC) occurs during stopping. INFO Coast to Stop with Timer If the Stop Command is input (i.e., the Run Command is turned OFF) when b1-03 is set to 3, the Inverter output is interrupted to coast the motor to a stop. After the Stop Command is input, Run Commands are ignored until the time T has elapsed. The time T depends upon the output frequency when the Stop Command is input and the deceleration time. Run Command ON OFF ON OFF ON Operation wait time T Deceleration time (e.g., C1-02) Output frequency Inverter output voltage interrupted Operation wait time T Minimum baseblock time (L2-03) Output frequency at Stop Command input Minimum output frequency 100% (Maximum output frequency) Fig 6.17 Coast to Stop with Timer 6-15 Using the DC Injection Brake Set constant b2-03 to apply the DC injection braking current to the motor while it is coasting to a stop, to stop the motor and then restart it. Set b2-03 to 0 to disable the DC injection brake at start. Set the DC injection brake current using b2-02. DC injection braking is used at startup for flux vector control with the current set in E2-03 (Motor no-load current). Related Constants Name Constant Number Display b2-02 DC injection braking current DCInj Current DC injection braking time at start b2-03 DCInj Time@Start Description Setting Range Factory Setting Change during Operation Sets the DC injection braking current as a percentage of the Inverter rated current. 0 to 100 50% Used to set the time to perform DC injection braking at start in units of 1 second. Used to stop coasting motor and restart it. When the set value is 0, DC injection braking at start is not performed. 0.00 to 10.00 0.00 s Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A No No 18AH No A A A A A 18BH Inputting the DC Injection Brake Command from Control Circuit Terminals If you set a multi-function contact input terminal (H1-) to 60 (DC injection brake command), you can apply the DC injection brake to the motor by turning ON the terminal for which the DC injection brake command has been set when the Inverter is being stopped. DC injection braking is used at startup for flux vector control. The time chart for the DC injection brake is shown below. DC injection brake command FRUN Output frequency DC injection brake E1-09 (DC injection braking at startup is used for flux vector control.) b2-01 DC injection brake (DC injection braking at startup is used for flux vector control.) If you input the DC injection brake command from an external terminal, or if the Run Command and jog command are input, the DC injection brake will be disabled, and operation will resume. Fig 6.18 DC Injection Brake Time Chart 6-16 Stopping Methods Changing the DC Injection Brake Current Using an Analog Input If you set H3-09 (Multi-function Analog Input Terminal A2 Function Selection) or H3-05 (Multi-function Analog Input Terminal A3 Function Selection) to 6 (DC injection brake current), you can change the DC injection brake current level using the analog input. At 10 V input (voltage) or 20 mA input (current), 100% of the Inverter rated current will be applied. DC injection brake voltage level Inverter rated current Fig 6.19 DC Injection Brake Current Using an Analog Input Using an Emergency Stop Set a multi-function input terminal (H1-) to 15 or 17 (emergency stop) to decelerate to a stop at the deceleration time set in C1-09. If inputting the emergency stop with an NO contact, set the multi-function input terminal (H1-) to 15, and if inputting the emergency stop with an NC contact, set the multi-function input terminal (H1-) to 17. After the emergency Stop Command has been input, operation cannot be restarted until the Inverter has stopped. To cancel the emergency stop, turn OFF the Run Command and emergency Stop Command. Related Parameters Name Constant Number C1-09 Display Description Emergency stop The deceleration time when the time multi-function input “Emergency (fast) stop” is set to ON. This function can be used as a Fast Stop Time stopping method when a fault has been detected. Setting Range Factory Setting 0.0 to 6000.0 10.0 s Change during Operation No Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A MEMO BUS Register 208H * * The setting range for acceleration/deceleration times depends on the setting of C1-10 (Acceleration/deceleration Time Setting Unit). If C1-10 is set to 0, the setting range is 0.00 to 600.00 (s). 6-17 Acceleration and Deceleration Characteristics This section explains the acceleration and deceleration characteristics of the Inverter. Setting Acceleration and Deceleration Times Acceleration time indicates the time taken for the output frequency to climb from 0% to 100%. Deceleration time indicates the time taken for the output frequency to reduce to 0%. The factory setting of the acceleration time is C1-01, and the factory setting of the deceleration time is C1-02. Related Parameters Name Constant Number C1-01 Display Acceleration time 1 Accel Time 1 C1-02 Deceleration time 1 Decel Time 1 C1-03 Acceleration time 2 Accel Time 2 C1-04 Deceleration time 2 Decel Time 2 C1-05 Acceleration time 3 Accel Time 3 C1-06 Deceleration time 3 Decel Time 3 C1-07 Acceleration time 4 Accel Time 4 C1-08 Deceleration time 4 Decel Time 4 C1-10 Accel/decel time setting unit Acc/Dec Units 6-18 Description Setting Range Factory Setting Change during Operation Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 MEMO BUS Register Sets the acceleration time to accelerate from 0 to the maximum output frequency, in 1-second units. Yes Q Q Q Q Q 200H Sets the deceleration time to decelerate from the maximum output frequency to 0, in 1-second units. Yes Q Q Q Q Q 201H The acceleration time when the multi-function input “accel/decel time 1” is set to ON. Yes A A A A A 202H The deceleration time when the multi-function input “accel/decel time 1” is set to ON. Yes A A A A A 203H No A A A A A 204H The deceleration time when the multi-function input “accel/decel time 2” is set to ON. No A A A A A 205H The acceleration time when the multi-function input “accel/decel time 1” and “accel/decel time 2” are set to ON. No A A A A A 206H The deceleration time when the multi-function input “accel/decel time 1” and “accel/decel time 2” are set to ON. No A A A A A 207H No A A A A A 209H The acceleration time when the multi-function input “accel/decel time 2” is set to ON. 0: 0.01-second units 1: 0.1-second units 0.0 to 6000.0 10.0 s * 0 or 1 1 Acceleration and Deceleration Characteristics Name Constant Number Factory Setting Change during Operation Sets the frequency for automatic acceleration/deceleration switching. Below set frequency: Accel/decel time 4 Above set frequency: Accel/decel time 1 The multi-function input “accel/ decel time 1” or “accel/decel time 2” take priority. 0.0 to 400.0 0.0 Hz 0.00 to 2.50 All sections of the S-curve characteristic time are set in seconds units. When the S-curve characteristic 0.00 to time is set, the accel/decel times 2.50 will increase by only half of the Scurve characteristic times at start and end. Display Accel/decel time switching frequency C1-11 Acc/Dec SW Freq C2-01 Description Setting Range S-curve characteristic time at acceleration start Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 20AH 0.20 s No A A A A A 20BH 0.20 s No A A A A A 20CH 0.00 to 2.50 0.20 s No A A A A A 20DH 0.00 to 2.50 0.00 s No A A A A A 20EH SCrv Acc @ Start C2-02 S-curve characteristic time at acceleration end SCrv Acc @ End C2-03 S-curve characteristic time at deceleration start SCrv Dec @ Start C2-04 S-curve characteristic time at deceleration end Run Command Output frequency OFF ON C2-02 C2-01 C2-03 C2-04 Time SCrv Dec @ End * The setting range for acceleration/deceleration times depends on the setting of C1-10 (Acceleration/deceleration Time Setting Unit). If C1-10 is set to 0, the setting range is 0.00 to 600.00 (s). Setting Acceleration and Deceleration Time Units Set the acceleration/deceleration time units using C1-10. Constant C1-10 is set to 1 at the factory. Set value Details 0 The acceleration/deceleration time settings range is 0.00 to 600.00 in units of 0.01 s. 1 The acceleration/deceleration time settings range is 0.00 to 6000.0 in units of 0.1 s. Switching Acceleration and Deceleration Time Using Multi-Function Input Terminal Commands Using the Inverter, you can set four acceleration times and four deceleration times. When the multi-function input terminals (H1-) are set to 7 (acceleration/deceleration time selection 1) and 1A (acceleration/deceleration time selection 2), you can switch the acceleration/deceleration time even during operation by combining the ON/OFF status of the terminals. The following table shows the acceleration/deceleration time switching combinations. 6-19 Acceleration/DeceleraAcceleration/Deceleration Time Selection 1 Ter- tion Time Selection 2 Terminal minal Acceleration Time Deceleration Time OFF OFF C1-01 C1-02 ON OFF C1-03 C1-04 OFF ON C1-05 C1-06 ON ON C1-07 C1-08 Switching Acceleration and Deceleration Time Automatically Use this setting when you want to switch acceleration/deceleration time automatically using the set frequency. When the output frequency reaches the set value in C1-11, the Inverter switches the acceleration/deceleration time automatically as shown in the following diagram. Set C1-11 to a value other than 0.0 Hz. If C1-11 is set to 0.0 Hz, the function will be disabled. Output frequency Acceleration/ deceleration time switching frequency (C1-11) C1-07 rate C1-01 rate C1-02 rate C1-08 rate When output frequency ≥ C1-11, acceleration and deceleration are performed using Acceleration/deceleration Time 1 (C1-01, C1-02). When output frequency < C1-11, acceleration and deceleration are performed using Acceleration/deceleration Time 4 (C1-07, C1-08). Fig 6.20 Acceleration/deceleration Time Switching Frequency Adjusting Acceleration and Deceleration Time Using an Analog Input If you set H3-09 (Multi-function Analog Input Terminal A2 Function Selection) or H3-05 (Multi-function Analog Input Terminal A3 Function Selection) to 5 (acceleration/deceleration time gain), you can adjust the acceleration/deceleration time using terminal A2's input voltage. The Inverter's acceleration time when the acceleration time has been set in C1-01 is as follows: Acceleration time = C1-01 set value x acceleration/deceleration time gain Acceleration/deceleration time gain (set value: 5) (Acceleration/deceleration gain from 1 to 10 V) = 10 V/Input voltage (V) x 10 (%) Fig 6.21 Acceleration/Deceleration Time Gain Using an Analog Input 6-20 Acceleration and Deceleration Characteristics Entering S-curve Characteristics in the Acceleration and Deceleration Time By performing acceleration and deceleration using an S-curve pattern, you can reduce shock when starting and stopping the machine. Using the Inverter, you can set an S-curve characteristic time for each of the following: Acceleration start time, deceleration start time, acceleration end time, and deceleration end time. INFO Set the S-curve characteristic time to lengthen acceleration/deceleration time as follows: Acceleration time = Selected acceleration time + (Acceleration start time S-curve characteristic time + Acceleration end time S-curve characteristic time) / 2 Deceleration time = Selected deceleration time + (Deceleration start time S-curve characteristic time + Deceleration end time S-curve characteristic time) / 2 Setting Example The S-curve characteristic when switching operation (forward/reverse) is shown in the following diagram. Forward Reverse C2-02 Output frequency C2-03 C2-04 C2-01 C2-04 C2-01 C2-02 C2-03 Fig 6.22 S-curve Characteristic during Operation Switching 6-21 Accelerating and Decelerating Heavy Loads (Dwell Function) The dwell function stores the output frequency when starting or stopping heavy loads. By temporarily storing the output frequency, you can prevent the motor from stalling. When using the dwell function, you must select a deceleration stop. Set b1-03 (Stopping Method Selection) to 0. Related Parameters Name Constant Number b6-01 Display Description Dwell frequency at start Dwell Ref @Start b6-02 b6-03 Dwell time at start Dwell frequency at stop Dwell time at stop 6-22 ON Dwell Time @Stop b6-01 b6-03 b6-02 Factory Setting Change during Operation 0.0 to 400.0 0.0 Hz 0.0 to 10.0 Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 1B6H 0.0 s No A A A A A 1B7H 0.0 to 400.0 0.0 Hz No A A A A A 1B8H 0.0 to 10.0 0.0 s No A A A A A 1B9H OFF Output frequency Dwell Time@Start Dwell Ref @Stop b6-04 Run command Setting Range Time b6-04 The dwell function is used to output frequency temporarily when driving a motor with a heavy load. Acceleration and Deceleration Characteristics Preventing the Motor from Stalling During Acceleration (Stall Prevention During Acceleration Function) The Stall Prevention During Acceleration function prevents the motor from stalling if a heavy load is placed on the motor, or sudden rapid acceleration is performed. If you set L3-01 to 1 (enabled) and the Inverter output current exceeds the -15% level of the set value in L302, the acceleration rate will begin to slow down. When L3-02 is exceeded, acceleration will stop. If you set L3-01 to 2 (optimum adjustment), the motor current accelerates to the value set in L3-02. With this setting, the acceleration time setting is ignored. Related Parameters Name Constant Number Display Stall prevention selection during accel L3-01 StallP Accel Sel Stall prevention level during accel L3-02 StallP Accel Lvl L3-03 Stall prevention limit during accel StallP CHP Lvl Description Setting Range Factory Setting Change during Operation 0: Disabled (Acceleration as set. With a heavy load, the motor may stall.) 1: Enabled (Acceleration stopped when L3-02 level is exceeded. Acceleration starts again when the current is returned.) 2: Intelligent acceleration mode (Using the L3-02 level as a basis, acceleration is automatically adjusted. Set acceleration time is disregarded.) 0 to 2 1 Effective when L3-01 is set to 1 or 2. Set as a percentage of Inverter rated current. Usually setting is not necessary. The factory setting reduces the set values when the motor stalls. 0 to 200 Sets the lower limit for stall prevention during acceleration, as a percentage of the Inverter rated current, when operation is in the frequency range above E1-06. Usually setting is not necessary. 0 to 100 Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A No No 48FH 150% No A A A No No 490H 50% No A A A No No 491H 6-23 Time Chart The following figure shows the frequency characteristics when L3-01 is set to 1. Output current Stall level during acceleration Time Output frequency Output frequency is controlled to prevent the motor stalling. Time Fig 6.23 Time Chart for Stall Prevention During Acceleration Setting Precautions • If the motor capacity is small compared to the Inverter capacity, or if the motor is operated using the fac- tory settings, resulting in the motor stalling, lower the set value of L3-02. • If using the motor in the constant output range, L3-02 will be automatically lowered to prevent stalling. L3-03 is the limit value to prevent the stall prevention level in the constant output range from being reduced more than necessary. • Set the constants as a percent taking the Inverter rated voltage to be 100%. Stall prevention level during acceleration L3-02 (Stall Prevention Level during Acceleration) L3-02 x L3-03 (Stall Prevention Limit during Acceleration) E1-06 Base Frequency (FA) Output frequency Fig 6.24 Stall Prevention Level and Limit During Acceleration 6-24 Acceleration and Deceleration Characteristics Preventing Overvoltage During Deceleration (Stall Prevention During Deceleration Function) The Stall Prevention During Deceleration function makes the rate of deceleration more gentle to suppress increases in DC bus voltage when the DC bus voltage exceeds the set value during motor deceleration. This function automatically lengthens the deceleration time with respect to the bus voltage, even if the deceleration time has been set to a considerably small value. If L3-04 is set to 1 or 2, when the main circuit DC voltage approaches the stall prevention level during deceleration, deceleration stops, and when deceleration falls below the level, is restarted. Using this operation, deceleration time is automatically lengthened. If L3-04 is set to 1, deceleration time returns to the set value, and if L3-04 is set to 2, deceleration is automatically adjusted to a faster deceleration time within the range of the stall prevention level during deceleration. Related Constants Name Constant Number Display Description Setting Range Factory Setting Change during Operation 0 to 3* 1 No Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 Q Q Q Q Q MEMO BUS Register Stall prevention selection during decel L3-04 0: Disabled (Deceleration as set. If deceleration time is too short, a main circuit overvoltage may result.) 1: Enabled (Deceleration is stopped when the main circuit voltage exceeds the overvoltage level. Deceleration restarts when voltage is returned.) 2: Intelligent deceleration mode (Deceleration rate is automatically adjusted so that StallP Decel Sel the Inverter can decelerate in the shortest possible time. Set deceleration time is disregarded.) 3: Enabled (with Braking Resistor Unit) When a braking option (Braking Resistor, Braking Resistor Unit, Braking Unit) is used, always set to 0 or 3. 492H * The setting range for flux vector and open-loop vector 2 controls is 0 to 2. 6-25 Setting Example An example of stall prevention during deceleration when L3-04 is set to 1 as shown below. Deceleration time controlled to prevent overvoltage Output frequency Time Deceleration time (set value) Fig 6.25 Stall Prevention During Deceleration Operation Setting Precautions • The stall prevention level during deceleration differs depending on the Inverter capacity. Refer to the fol- lowing table for details. Inverter Capacity 200 V Class 400 V Class Stall Prevention Level during Deceleration (V) 380 E1-01 ≥ 400 V 760 E1-01 < 400 V 660 • When using the braking option (braking resistor, Braking Resistor Units, and Braking Units), be sure to set constant L3-04 to 0 or 3. • To decelerate at a shorter time than the deceleration time set when L3-04 is set to 0 with the braking option enabled, set L3-04 to 3. • The setting of L3-04 is ignored for flux vector control or open-loop vector 2 control. Preventing Overvoltage by Automatically Reducing the Regenerative Torque Limit (Overvoltage Inhibit Function, PRG: 102 only) The overvoltage inhibit function is a function that, by reducing the regenerative torque limit to a value less than its set value according to the main circuit voltage level, suppresses voltage rises with regenerative torque. Using this function means that if, for example, the main circuit voltage rises during deceleration, the regenerative torque limit will be reduced and so the deceleration rate will be reduced automatically, suppressing rises in the main circuit voltage. This function is effective for suppressing overvoltages that occur during stabilization after an overshoot following sudden acceleration. This function differs from the stall prevention during deceleration function in this respect. This function is enabled during vector control. 6-26 Acceleration and Deceleration Characteristics Related Constants Name Constant Number Description Setting Range 0: Disabled 1: Enabled Used to enable or disable the function for inhibiting main circuit overvoltages by reducing the regenerative torque limit according to the main circuit overvoltage level. If this function is enabled, when the main circuit voltage rises, operation will be performed with the regenerative torque less than the set value. 0 or 1 0 350 to 380 V* Display Overvoltage inhibit selection L3-11 OV Inhibit Sel Overvoltage inhibit voltage level L3-12 OV Inhbt VoltLv1 Change Factory during Setting Operation Sets the main circuit voltage level for which the regenerative torque limit is restricted to 0. Usually, there is no need to change this setting. If main circuit overvoltages occur even with the overvoltage inhibit function enabled, reduce this setting. 390* Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No No No A A A 4C7H No No No A A A 4C8H * These values are for a 200 V Class Inverter. For a 400 V Class Inverter, double the values. Setting Precautions When this function is enabled, if the main circuit voltage rises, the regenerative torque limit will decrease to a value less than its set value and so the motor will not rotate at the speed specified by the speed reference. Therefore, in applications where it is necessary to rotate the motor at the speed specified by the speed reference, disable this function and use a converter, a dynamic braking resistor, or a power regenerative unit to suppress rises in the main circuit voltage. 6-27 Adjusting Frequency References This section explains methods of adjusting frequency references. Adjusting Analog Frequency References Gain and bias are among the constants used to adjust analog inputs. Related Constants Name Constant Number H3-01 Display Signal level selection (terminal A1) Term A1 Signal H3-02 H3-03 H3-04 Gain (terminal A1) Terminal A1 Gain Bias (terminal A1) Terminal A1 Bias Signal level selection (terminal A3) Term A3 Signal H3-05 Multi-function analog input (terminal A3) function selection Setting Range Factory Setting Change during Operation 0 or 1 0 Sets the frequency when 10 V is 0.0 to input, as a percentage of the maxi1000.0 mum output frequency. Sets the frequency when 0 V is -100.0 input, as a percentage of the maxito +100.0 mum frequency. Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 410H 100.0 % Yes A A A A A 411H 0.0% Yes A A A A A 412H 0 or 1 0 No A A A A A 413H Select multi-function analog input 0 to 1F function for terminal A3. 2 No A A A A A 414H Description 0: 0 to 10 V 1: -10 to 10 V [11-bit + polarity (positive/ negative) input] 0: 0 to 10 V 1: -10 to 10 V [11-bit + polarity (positive/ negative) input] Terminal A3 Sel H3-06 H3-07 H3-08 6-28 Gain (terminal A3) Sets the input gain (level) when 10 V is input. Set according to the 100% value selected from H3-05. 0.0 to 1000.0 100.0 % Yes A A A A A 415H Sets the input gain (level) when 0 V is input. Set according to the 100% value selected from H3-05. -100.0 to +100.0 0.0% Yes A A A A A 416H 0: 0 to 10 V 1: -10 to 10 V 2: 4 to 20 mA (9-bit input). Switch current and voltage input Term A2 Signal using the switch on the control panel. 0 to 2 2 No A A A A A 417H Terminal A3 Gain Bias (terminal A3) Terminal A3 Bias Signal level selection (terminal A2) Adjusting Frequency References Name Constant Number H3-09 Display Multi-function analog input (terminal A2) function selection Description Setting Range Select multi-function analog input 0 to 1F function for terminal A2. Factory Setting Change during Operation 0 Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 418H Terminal A2 Sel H3-10 H3-11 H3-12 Gain (terminal A2) Terminal A2 Gain Bias (terminal A2) Terminal A2 Bias Analog input filter time constant Filter Avg Time Sets the input gain (level) when 10 V (20 mA) is input. Set according to the 100% value for the function set for H3-09. 0.0 to 1000.0 100.0 % Yes A A A A A 419H Sets the input gain (level) when 0 V (4 mA) is input. Set according to the 100% value for the function set for H3-09. -100.0 to +100.0 0.0% Yes A A A A A 41AH Sets primary delay filter time constant in seconds for the analog 0.00 to input terminal. 2.00 Effective for noise control etc. 0.03 s No A A A A A 41BH Adjusting Analog Frequency Reference Using Constants The frequency reference is input from the control circuit terminals using analog voltage and current. If using frequency reference terminal A1 as an input terminal, perform adjustments using constants H3-02 and H3-03. If using multi-function analog input terminal A2 as a frequency reference terminal, perform adjustments using H3-10 and H3-11. Adjustment can be made using H3-06 and H3-07 when multi-function analog input terminal A3 is used as a frequency reference terminal. Frequency reference Frequency reference (H3-06) Terminal A2 input voltage (current) Terminal A1 (A3) input voltage (H3-07) Terminal A1, A3 input Terminal A2 input Fig 6.26 Terminals A1 and A2 Inputs 6-29 Adjusting Frequency Gain Using an Analog Input When H3-09 or H3-05 is set to 1 (frequency gain), you can adjust the frequency gain using the analog input terminal A2 or A3. Frequency gain Multi-function analog input terminal A2 input level Fig 6.27 Frequency Gain Adjustment (Terminal A2 Input) The frequency gain for terminal A1 is the product of H3-02 and terminal A2 gain. For example, when H3-02 is set to 100% and terminal A2 is set to 5 V, the terminal A1 frequency reference will be 50%. Frequency reference 100% H3-02 50% H3-02 0.5 Terminal A1 input voltage 0 10 V Adjusting Frequency Bias Using an Analog Input When constant H3-09 or H3-05 is set to 0 (add to terminal A1), the frequency equivalent to the terminal A2 or A3 input voltage is added to A1 as a bias. Frequency bias Multi-function analog input terminal A2 or A3 input level Fig 6.28 Frequency Bias Adjustment (Terminal A2 or A3 Input) For example, if H3-02 is 100%, H3-03 is 0%, and terminal A2 is set to 1 V, the frequency reference from terminal A1 when 0 V is input to A1 will be 10%. 6-30 Adjusting Frequency References Frequency reference H3-02 10% Bias Terminal A1 input voltage 0V 10 V When constant H3-09 or H3-05 is set to D (frequency bias 2), the frequency equivalent to the terminal A2 or A3 input voltage is added to A1 as a bias. Operation Avoiding Resonance (Jump Frequency Function) The jump frequency function operates the motor while avoiding resonance caused by characteristic frequencies in the machinery. This function is effective in creating a frequency reference dead band. During constant-speed operation, operation within the jump frequency range is prohibited. Smooth operation still used during acceleration and deceleration, i.e., jumps are not performed. Related Constants Name Constant Number d3-01 Display Jump frequency 1 Jump Freq 1 d3-02 Jump frequency 2 Jump Freq 2 d3-03 Jump frequency 3 Jump Freq 3 d3-04 Jump frequency width Jump Bandwidth Description Setting Range Set the center values of the jump frequencies in Hz. This function is disabled by setting the jump frequency to 0 Hz. Always ensure that the following applies: d3-01 ≥ d3-02 ≥ d3-03 Operation in the jump frequency range is prohibited but during acceleration and deceleration, speed changes smoothly without jump. 0.0 to 400.0 Sets the jump frequency bandwidth in Hz. The jump frequency will be the jump frequency ± d3-04. 0.0 to 20.0 Factory Setting Change during Operation 0.0 Hz Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 294H 0.0 Hz No A A A A A 295H 0.0 Hz No A A A A A 296H 1.0 Hz No A A A A A 297H The relationship between the output frequency and the jump frequency reference is as follows: 6-31 Output frequency Frequency reference descending Jump frequency width d3-04 Frequency reference ascending Jump frequency width d3-04 Jump frequency width d3-04 Jump frequency reference Jump frequency 3 (d3-03) Jump frequency 2 (d3-02) Jump frequency 1 (d3-01) Fig 6.29 Jump Frequency Setting Jump Frequency Reference Using an Analog Input When constant H3-09 (Multi-function Analog Input Terminal A2 Function Selection) or H3-05 (Multi-function Analog Input Terminal A3 Function Selection) is set to A (jump frequency), you can change the jump frequency using the terminal A2 input level. Jump frequency Max. output frequency E1-04 0V (4 mA) Multi-function analog input 10 V terminal A2 or A3 input level (20 mA) Fig 6.30 Jump Frequency Setting Using an Analog Input Setting Precautions • Set the jump frequency according to the following formula: d3-01 ≥ d3-02 ≥ d3-03 > Analog input. • When constants d3-01 to d3-03 are set to 0 Hz, the jump frequency function is disabled. 6-32 Adjusting Frequency References Adjusting Frequency Reference Using Pulse Train Inputs The frequency reference can be adjusted when b1-01 (Reference Selection) is set to 4 (Pulse Train Input). Set the pulse frequency in constant H6-02 to 100% reference, and then adjust the gain and bias accordingly using H6-03 and H6-04. Related Constants Name Constant Number H6-01 H6-04 H6-05 Change during Operation 0: Frequency reference 1: PID feedback value 2: PID target value 0 to 2 0 Set the number of pulses in hertz, taking the reference to be 100%. 1000 to 32000 Set the input gain level as a percent when the pulse train set in H6-02 is input. Control Methods MEMO BUS Register V/f Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 42CH 1440 Hz Yes A A A A A 42DH 0.0 to 1000.0 100.0 % Yes A A A A A 42EH Set the input bias when the pulse train is 0. -100.0 to 100.0 0.0% Yes A A A A A 42FH Pulse train Set the pulse train input primary input filter time delay filter time constant in seconds. PI Filter Time 0.00 to 2.00 0.10 s Yes A A A A A 430H Display Pulse train input function selection Pulse train input scaling PI Scaling H6-03 Factory Setting V/f with PG Pulse Input Sel H6-02 Description Setting Range Pulse train input gain Pulse Input Gain Pulse train input bias Pulse Input Bias The following diagram shows the method for adjusting the frequency reference using pulse inputs. Gain and bias Filter RP Pulse Cycle measurement =0 H6-03 =1 1 1+sT H6-04 H6-05 0 100 =2 Master speed frequency PID feedback PID target value H6-01 Scaling using H6-02 Fig 6.31 Frequency Reference Adjustments Using Pulse Train Inputs 6-33 Speed Limit (Frequency Reference Limit Function) This section explains how to limit the motor speed. Limiting Maximum Output Frequency If you do not want the motor to rotate above a given frequency, use constant d2-01. Set the upper limit value of the Inverter output frequency as a percent, taking E1-04 (Maximum Output Frequency) to be 100%. Related Constants Name Constant Number d2-01 Display Frequency reference upper limit Ref Upper Limit Description Setting Range Change Factory during Setting Operation Set the output frequency upper limit as a percent, taking the max. output frequency to be 100%. 0.0 to 110.0 100.0 % No Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A MEMO BUS Register 289H Limiting Minimum Frequency If you do not want the motor to rotate at below a given frequency, use constants d2-02 or d2-03. There are two methods of limiting the minimum frequency, as follows: • Adjust the minimum level for all frequencies. • Adjust the minimum level for the master speed frequency (i.e., the lower levels of the jog frequency, multi- step speed frequency, and auxiliary frequency will not be adjusted). Related Constants Name Constant Number d2-02 Display Frequency reference lower limit Ref Lower Limit d2-03 6-34 Description Setting Range Change Factory during Setting Operation Sets the output frequency lower limit as a percentage of the maximum output frequency. 0.0 to 110.0 0.0% 0.0 to 110.0 0.0% Master speed reference lower Set the master speed reference lower limit as a percent, taking limit the max. output frequency to be Ref1 Lower 100%. Limit Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 28AH No A A A A A 293H Speed Limit (Frequency Reference Limit Function) Adjusting Frequency Lower Limit Using an Analog Input If you set constant H3-09 (Multi-function Analog Input Terminal A2 Function Selection) or H3-05 (Multifunction Analog Input Terminal A3 Function Selection) to 9 (frequency reference lower limit level), you can adjust the frequency lower level using the terminal A2 input level. Output frequency lower level Max. output frequency E1-04 0V (4 mA) Multi-function analog input 10 V terminal A2 or A3 input level (20 mA) Fig 6.32 Output Frequency Lower Level for Multi-function Analog Input If constant d2-02 and terminal A2 output frequency lower level have been set at the same time, the larger set value will become the frequency lower limit. INFO 6-35 Improved Operating Efficiency This section explains functions for improving motor operating efficiency. Reducing Motor Speed Fluctuation (Slip Compensation Function) When the load is large, the amount of motor slip also grows large and the motor speed decreases. The slip compensation function controls the motor at a constant speed, regardless of changes in load. When the motor is operating at the rated load, constant E2-02 (Motor Rated Slip) × the frequency in constant C3-01 is added to the output frequency. Related Constants Name Constant Number Display Description Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 MEMO BUS Register Slip compensation gain C3-01 Used to improve speed accuracy when operating with a load. Usually setting is not necessary. Adjust this constant at the following times. • When actual speed is low, increase the set value. Slip Comp Gain • When actual speed is high, decrease the set value. Used as the applicable control gain when using flux vector control. Setting Range Change Factory during Setting Operation Slip compensation primary delay time C3-02 Slip Comp Time C3-03 Slip compensation limit Slip Comp Limit Slip compensation selection during regeneration C3-04 Slip Comp Regen C3-05 Output voltage limit operation selection Output V limit Slip compensation primary delay time is set in ms units. Usually setting is not necessary. Adjust this constant at the following times. • Reduce the setting when slip compensation responsive is slow. • When speed is not stabilized, increase the setting. Sets the slip compensation limit as a percentage of motor rated slip. 0.0 to 2.5 0 to 10000 1.0* Yes A No A A No 20FH 200 ms No A No A No No 210H * 0 to 250 200% No A No A No No 211H 0: Disabled. 1: Enabled. When the slip compensation during regeneration function has been activated, as regeneration capacity increases momentarily, it may be necessary to use a braking option (braking resistor, Braking Resistor Unit or Braking Unit.) 0 or 1 0 No A No A No No 212H 0: Disabled. 1: Enabled. (The motor flux will be lowered automatically when the output voltage become saturated.) 0 or 1 0 No No No A A No 213H * The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given. 6-36 Improved Operating Efficiency Adjusting Slip Compensation Gain You can switch the C3-01 constant settings as shown below by changing the control method. • V/f control: 0.0 • Open-loop vector control: 1.0 • Flux vector control: 1.0 Set C3-01 to 1.0 to compensate the rated slip set using the rated torque output status. Adjust the slip compensation gain using the following procedure. 1. Set E2-02 (Motor Rated Slip) and E2-03 (Motor No-load Current) correctly. You can calculate the motor rated slip from the values on the motor nameplate using the following formula. Amount of motor rated slip (Hz) = Motor rated frequency (Hz) - No. of rated rotations (min−1.) × No. of motor poles / 120 Set the values for rated voltage, rated frequency, and no-load current in the motor unladen current. The motor rated slip is set automatically in the vector control using autotuning. 2. In V/f control, set C3-01 to 1.0. Setting this constant to 0.0 disables slip compensation. 3. Apply a load, and measure the speed to adjust the slip compensation gain. Adjust the slip compensation gain by 0.1 at a time. If the speed is less than the target value, increase the slip compensation gain, and if the speed is greater than the target value, reduce the slip compensation gain. For flux vector control, the slip compensation gain is used as the motor temperature compensation gain. When the motor temperate increases, the motor’s internal constant increases, resulting in an increase in slip. If C3-01 is set, the amount of slip is adjusted as the temperature rises. Set C3-01 if the amount of torque varies with the temperature when using torque control or a torque limit. The larger the value of C3-01, the larger the compensation. Adjusting Slip Compensation Primary Delay Time Constant Set the slip compensation primary delay time constant in ms. You can switch the factory settings as follows by changing the control method. • V/f control: 2000 ms • Open-loop vector control: 200 ms Normally, there is no need to make these settings. When the slip compensation response is low, lower the set value. When the speed is unstable, increase the set value. Adjusting Slip Compensation Limit In C3-03, set the upper limit for the slip compensation amount as a percent, taking the motor rated slip amount as 100%. If the speed is lower than the target value but does not change even when you adjust the slip compensation gain, the motor may have reached the slip compensation limit. Increase the limit, and check the speed again. Make the settings, however, to make sure that the value of the slip compensation limit and reference frequency does not exceed the tolerance of the machine. The following diagram shows the slip compensation limit for the constant torque range and fixed output range. 6-37 Slip compensation limit Output frequency E1-06: Base frequency E1-04: Maximum output frequency Fig 6.33 Slip Compensation Limit Selecting Slip Compensation Function During Regeneration Set whether to enable or disable the slip compensation function during regeneration. If the slip compensation function operates during regeneration, you might have to use the braking option (braking resistor, Braking Resistor Unit, and Braking Unit) to momentarily increase the regenerative amount. Selecting Output Voltage Limit Operation If output voltage saturation occurs while the output voltage limit operation is disabled, the output current will not change, but torque control accuracy will be lost. If torque control accuracy is required, change the settings to enable the output voltage limit operation. If the output voltage limit operation is enabled, motor magnetic flux current is controlled automatically, and torque control accuracy is maintained to limit the output voltage references. Consequently, the output current will increase by approximately 10% maximum (with rated load) compared with when the output voltage limit operation is disabled, so check the Inverter current margin. Setting Precautions • If using the device at medium to low speed only, if the power supply voltage is 10% or more higher than the motor rated voltage, or if the torque control accuracy at high speeds is insufficient, it is not necessary to change the output voltage limit operation. • If the power supply voltage is too low compared with the motor rated voltage, torque control accuracy may be lost even if the output voltage limit operation is enabled. Compensating for Insufficient Torque at Startup and Low-speed Operation (Torque Compensation) The torque compensation function detects that the motor load has increased, and increases the output torque. V/f control calculates and adjusts the motor primary loss voltage according to the output voltage (V), and compensates for insufficient torque at startup and during low-speed operation. Calculate the compensation voltage as follows: Motor primary voltage loss × constant C4-01. Vector control separates the motor excitation current and the torque current by calculating the motor primary current, and controlling each of the two separately. Calculate the torque current as follows: Calculated torque reference × C4-01 6-38 Improved Operating Efficiency Related Constants Name Constant Number Display Torque compensation gain C4-01 Torq Comp Gain Torque compensation primary delay time constant C4-02 Torq Comp Time Description Setting Range Sets torque compensation gain as a ratio. Usually setting is not necessary. Adjust in the following circumstances: • When the cable is long; increase the set value. • When the motor capacity is smaller than the Inverter capacity (Max. applicable motor capacity), increase the set val- 0.00 to ues. 2.50 • When the motor is oscillating, decrease the set values. Adjust the output current range at minimum speed rotation so that it does not exceed the Inverter rated output current. Do not alter the torque compensation gain from its default (1.00) when using the open-loop vector1 control method. The torque compensation delay time is set in ms units. Usually setting is not necessary. Adjust in the following circumstances: • When the motor is oscillating, increase the set values. • When the responsiveness of the motor is low, decrease the set values. 0 to 10000 Change Factory during Setting Operation 1.00 20 ms * Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 Yes A A A No No 215H No A A A No No 216H * The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given. Adjusting Torque Compensation Gain Normally, there is no need to make this adjustment. Do not adjust the torque compensation gain when using open-loop vector control. Adjust the torque compensation gain using V/f control in the following circumstances. • If the cable is very long, increase the set value. • If the (maximum applicable) motor capacity is smaller than the Inverter capacity, increase the set value. • If the motor is vibrating, reduce the set value. Adjust this constant so that the output current during low-speed rotation does not exceed the Inverter rated output current range. Adjusting the Torque Compensation Primary Delay Time Constant Set the torque compensation function primary delay in ms. You can switch the factory settings as follows by changing the control method settings: • V/f control: 200 ms • V/f control with PG: 200 ms • Open-loop vector control: 20 ms 6-39 Normally, there is no need to make this setting. Adjust the constant as shown below. • If the motor is vibrating, increase the set value. • If the motor response is low, decrease the set value. Hunting-prevention Function The hunting-prevention function suppresses hunting when the motor is operating with a light load. This function can be used in V/f and V/f with PG. Related Constants Name Constant Number Display Hunting-prevention function selection N1-01 Hunt Prev Select Description Setting Range Factory Setting Change during Operation 0: Hunting-prevention function disabled 1: Hunting-prevention function enabled The hunting-prevention function suppresses hunting when the motor is operating with a light load. This function is enabled in V/f control method only. If high response is to be given priority over vibration suppression, disable the hunting-prevention function. 0 or 1 1 1.00 N1-02 Set the hunting-prevention gain multiplication factor. Normally, there is no need to make this setting. Make the adjustments as follows: • If vibration occurs with light 0.00 to load, increase the setting. 2.50 Hunt Prev Gain • If the motor stalls, reduce the setting. If the setting is too large, the voltage will be too suppressed and the motor may stall. N1-03 Hunting-prevention time constant Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A No No No 580H No A A No No No 581H No A A No No No 582H Hunting-prevention gain *1 Set the hunting-prevention primary delay time in units of ms. 0 to 500 10 ms*2 Hunt Prev Time * 1. Applicable for G7-Series Inverters with software version PRG: 1034 and later. * 2. The factory setting depends upon the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. 6-40 Improved Operating Efficiency Stabilizing Speed (Speed Feedback Detection Function) The speed feedback detection control (AFR) function measures the stability of the speed when a load is suddenly applied, by calculating the amount of fluctuation of the torque current feedback value, and compensating the output frequency with the amount of fluctuation. Related Constants Name Constant Number Display Speed feedback detection control (AFR) gain N2-01 AFR Gain N2-02 Speed feedback detection control (AFR) time constant Description Setting Range Factory Setting Change during Operation Set the internal speed feedback detection control gain using the multiplication function. Normally, there is no need to make this setting. Adjust this constant as follows: • If hunting occurs, increase the set value. • If response is low, decrease the set value. Adjust the setting by 0.05 at a time, while checking the response. 0.00 to 10.00 1.00 Set the time constant to decide the rate of change in the speed feedback detection control. 0 to 2000 Increase the setting if overvoltage (OV) failures occur at the completion of acceleration or when the load changes radically. 0 to 2000 Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No No No A No No 584H 50 ms No No No A No No 585H 750 ms No No No A No No 586H AFR Time N2-03 Speed feedback detection control (AFR) time constant 2 AFR Time 2 6-41 Machine Protection This section explains functions for protecting the machine. Reducing Noise and Leakage Current The switching frequency of the Inverter’s output transistor can be changed to reduce carrier noise and leakage current from the motor. Related Constants Name Constant Number C6-02 Display Control Methods Description Carrier frequency Select carrier wave fixed pattern. selection Select F to enable detailed settings using constants C6-03 to C6-07. Carrier Setting Range Change Factory during Setting Operation 1 to F 6 *2 *1 2.0 to 15.0 15.0 kHz *2 *5 *1 0.4 to 15.0 15.0 kHz *2 *5 *1 00 to 99 00 Open MEMO BUS Loop Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No Q Q Q Q No A A A A No 225H No A A No No No 226H No A A No No No 227H No No No No *4 *4 *4 *4 Q 22DH No *4 224H Freq Sel C6-03 *3 C6-04 *3 C6-05 *3 C6-11 Carrier frequency upper limit Carrier Freq Max Carrier frequency lower limit Carrier Freq Min 6-42 1. 2. 3. 4. 5. Carrier frequency Output frequency x (C6-05) x K Output Carrier frefrequency quency (Max. output frequency) proportional gain K is a coefficient that depends on the setting of C6-03. C6-03 ≥ 10.0 kHz: K = 3 Carrier Freq Gain 10.0 kHz > C6-03 ≥ 5.0 kHz: K = 2 5.0 kHz > C6-03: K = 1 Carrier frequency selection for openloop vector 2 control Carrier Freq Sel * * * * * Set the carrier frequency upper limit and lower limit in kHz units. The carrier frequency gain is set as follows: With the vector control method, the upper limit of the carrier frequency is fixed in C6-03. Select the carrier frequency when openloop vector 2 control is used. 1: 2 kHz 2: 4 kHz 3: 6 kHz 4: 8 kHz 1 to 4 4 *1 No The factory settings depend on the capacity of the Inverter. The values for a 200 V Class Inverter for 0.4 kW are given. The setting ranges depend on the capacity of the Inverter. The values for a 200 V Class Inverter for 0.4 kW are given. This constant can be monitored or set only when F is set for C6-02. Displayed in Quick Programming Mode when motor 2 is set for a multi-function input. The maximum output frequency depends on the setting for the carrier frequency (refer to page 6-43). Machine Protection Control Method and Carrier Frequency Settings Carrier frequency settings are restricted as listed in the following table according to the control method selection. Control Method V/f control with or without a PG Open-loop vector 1 control or Flux vector control Open-loop vector 2 control Carrier Frequency 1: 2.0 kHz 2: 5.0 kHz 3: 8.0 kHz 4: 10.0 kHz 5: 12.5 kHz 6: 15.0 kHz F: Any setting* Detailed settings are available in C6-03, C6-04, and C6-05. 1: 2.0 kHz 2: 5.0 kHz 3: 8.0 kHz 4: 10.0 kHz 5: 12.5 kHz 6: 15.0 kHz F: Any setting* The upper limit of the carrier frequency is determined by C6-03. 1: 2.0 kHz 2: 4.0 kHz 3: 6.0 kHz 4: 8.0 kHz * The upper limit of the carrier frequency depends on the Inverter capacity. Carrier Frequency Setting Precautions When selecting the carrier frequency, observe the following precautions. • Adjust the carrier frequency according to the cases shown below. If the wiring distance between Inverter and motor is long: Set the carrier frequency low. (Use the following values as guidelines.) Wiring Length 50 m or less 100 m or less Over 100 m C6-02 (carrier frequency selection) setting 1 to 6 (15 kHz) 1 to 4 (10 kHz) 1 to 2 (5 kHz) If speed and torque are inconsistent at low speeds: Set the carrier frequency low. If leakage current from the Inverter is large: Set the carrier frequency low. If metallic noise from the motor is large: Set the carrier frequency high. • When using V/f control or V/f control with PG, you can vary the carrier frequency according to the output frequency, as shown in the following diagram, by setting C6-03 (Carrier Frequency Upper Limit), C6-04 (Carrier Frequency Lower Limit), and C6-05 (Carrier Frequency Proportional Gain). 6-43 Carrier Frequency C6-03 Output frequency × C6-05 × K* C6-04 Output frequency E1-04 Max. Output Frequency * K is the coefficient determined by the set value in C6-03. C6-03 ≥ 10.0 kHz: K=3 10.0 kHz > C6-03 ≥ 5.0 kHz: K=2 5.0 kHz < C6-03: K=1 Fig 6.34 • With vector control, the carrier frequency is fixed to the Carrier Frequency Upper Limit in C6-03 if user- set or by the carrier frequency set in C6-02. • To fix the carrier frequency, set C6-03 and C6-04 to the same value, or set C6-05 to 0. • If the settings are as shown below, OPE11 (Constant setting error) will occur. If Carrier Frequency Proportional Gain (C6-05) > 6 and C6-03 < C6-04. • The Inverter overload current level can be reduced by the carrier frequency setting, and an OL2 (Inverter overload) may be detected even if the overload current is smaller than 150%. The reduction levels of the Inverter overload current are shown in the following figures. Overload current reduction level 100% 80% 200 V Class, 22 kW 50% 0 10 kHz 15 kHz Carrier frequency Fig 6.35 Reduction Levels for V/f, V/f with PG, Open-loop Vector 1, and Flux Vector Control 6-44 Machine Protection Overload current reduction level 100% 87% 200 V Class, 30 to 75 kW 50% Carrier frequency 0 8 kHz 4 kHz Fig 6.36 Reduction Levels for Open-loop Vector 2 Control For 400 V Class Inverters, the following limitations apply to the maximum output frequency that can be set for the carrier frequency settings. Carrier Frequency 0.4 kHz 1 kHz 2 kHz 3 kHz 5 kHz 8 kHz Maximum output frequency setting 33 Hz 83 Hz 166 Hz 250 Hz 400 Hz 400 Hz 40P4 to 4110 40P4 to 4075 40P4 to 4045 Applicable Inverter capacity CIMR-G7A 40P4 to 4300 6-45 Limiting Motor Torque (Torque Limit Function) The motor torque limit function is enabled with flux vector control and open-loop vector control. In the open-loop vector control and flux vector control, the user-set value is applied to the torque limit by calculating internally the torque output by the motor. Enable this function if you do not want a torque above a specified amount to be applied to the load, or if you do not want a regeneration value above a specified amount to occur. Related Constants Name Constant Number Display L7-01 Forward drive torque limit Control Methods Setting Range Description L7-03 Torq Lmt Fwd Rgn L7-04 Open Loop Vector 1 Flux Vector Open MEMO BUS Loop Vec- Register tor 2 200% No No No A A A 4A7H 0 to 300 200% No No No A A A 4A8H 0 to 300 200% No No No A A A 4A9H 0 to 300 200% No No No A A A 4AAH Set the integral time for the torque limit. When integral control is set for the torque limit, reduce this setting to increase the change in frequency for the torque limit. *Normally handled with PRG: 103. 5 to 10,000 200 ms No No No A No No 4ACH Select the control method for the torque limit during acceleration and deceleration. 0: Proportional control (integral control during constant speed) 1: Integral control Normally, this constant does not need to be set. *Normally handled with PRG: 103. 0, 1 0 No No No A No No 4C9H Reverse Sets the torque limit value as a percentdrive torque limit age of the motor rated torque. Four individual regions can be set. Torq Limit Output torque Rev Forward regenerative torque limit V/f V/f with PG 0 to 300 Torq Limit Fwd L7-02 Change Factory during Setting Operation Positive torque Reverse No. of motor rotations Regenerative state Regenerative state Forward Negative torque Reverse regenerative torque limit Torq Lmt Rev Rgn L7-06 Integral time setting for torque limit Torq Limit Time L7-07 Control method selection for torque limit during acceleration and deceleration Torque Limit Sel 6-46 Machine Protection Multi-function Analog Input (H3-05, H3-09) Control Methods Setting Value Function Contents (100%) V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 10 Positive torque limit Motor's rated torque No No Yes Yes Yes 11 Negative torque limit Motor's rated torque No No Yes Yes Yes 12 Regenerative torque limit Motor's rated torque No No Yes Yes Yes 15 Positive/negative torque limit Motor's rated torque No No Yes Yes Yes Note The forward torque limit is the limit value when the analog input signal generates forward torque. This torque limit setting is enabled even when the analog input signal generates forward torque while the motor is operating (regeneration). Setting the Torque Limit in Constants Using L7-01 to L7-04, you can set individually four torque limits in the following directions: Forward drive, reverse drive, forward regeneration, and reverse regeneration. Set the Torque Limit Value Using an Analog Input You can change the analog input level torque limit value by setting the torque limit in multi-function analog input terminals A2 and A3. The analog input terminal signal level is factory-set as follows: Multi-function analog input terminal A2: 4 to 20 mA Multi-function analog input terminal A3: 0 to 10 The following diagram shows the relationship between the torque limits. Output torque Positive Positive/negative torque limits Forward torque limit Regenerative torque limit No. of motor rotations Forward operation Reverse operation Regenerative torque limit Negative torque limit Positive/negative torque limits Negative Fig 6.37 Torque Limit by Analog Input 6-47 Setting Torque Limits Using Constants and an Analog Input The following block diagram shows the relationship between torque limit using constants and torque limit using an analog input. Multi-function analog input Forward torque limit Terminal (set value = 10) A2 or A3 Negative torque limit (set value = 11) Regenerative torque limit (set value = 12) Positive/negative torque limit (set value = 15) Positive forward drive torque Reverse positive regenerative torque Forward negative regenerative torque Min: Minimum value priority circuit Reverse drive reverse torque Forward torque limit (L7-01) Constants Forward torque limit Reverse torque limit (L7-02) Forward regenerative torque limit (L7-03) Reverse torque limit Reverse regenerative torque limit (L7-04) Reverse regenerative torque limit Forward regenerative torque limit 175% of Inverter rated current Fig 6.38 Torque Limit Using Constants and an Analog Input Selecting the Control Method for Torque Limit during Acceleration and Deceleration (PRG: 103 only) L7-07 is used to select the control method for the torque limit during acceleration and deceleration. The selections are proportional control and integral control. For applications, such as presses, in which the torque limit will be reached during acceleration and deceleration, torque control can be given priority by selecting integral control. To increase the change in frequency for the torque limit when integral control is selected, decrease the value set for L7-06 (Integral Time Setting for Torque Limit). Setting Precautions • When the torque limit function is operating, control and compensation of the motor speed is disabled because torque control is given priority. Therefore, the acceleration and deceleration times may increase or the number of motor rotations may decrease. • When using the torque limit to raise and lower loads, do not carelessly lower the torque limit value, as this may result in the motor falling or slipping. • Torque limits using an analog input are the upper limit value (during 10 V or 20 mA input) of 100% of the motor rated torque. To make the torque limit value during 10 V or 20 mA input 150% of the rated torque, set the input terminal gain to 150.0 (%). Adjust the gain for multi-function analog input terminal A2 using H3-10 and for multi-function analog input terminal A3 using H3-06. • The torque limit accuracy is ±5% at the output frequency of 10 Hz or above. When output frequency is less than 10 Hz, accuracy is lowered. • When the torque is limited while L7-07 is set to 1 (integral control), the acceleration and deceleration times may increase or the motor speed may not agree with the speed reference value. 6-48 Machine Protection Preventing Motor Stalling During Operation Stall prevention during operation prevents the motor from stalling by automatically lowering the Inverter's output frequency when a transient overload occurs while the motor is operating at a constant speed. Stall prevention during operation is enabled only during V/f control. If the Inverter output current continues to exceed the setting in constant L3-06 for 100 ms or longer, the motor speed is reduced. Set whether to enable or disable deceleration time using constant L3-05. Set the deceleration time using C1-02 (Acceleration time 1) or C1-04 (Acceleration Time 2). If the Inverter output current reaches the set value in L3-06 - 2% (Inverter Rated Output Current), the motor will accelerate again at the frequency set or the acceleration time set. Related Constants Name Constant Number Display Stall prevention selection during running L3-05 StallP Run Sel L3-06 Stall prevention level during running StallP Run Level Description Setting Range Factory Setting Change during Operation 0: Disabled (Runs as set. With a heavy load, the motor may stall.) 1: Deceleration time 1 (the deceleration time for the stall prevention function is C1-02.) 2: Deceleration time 2 (the deceleration time for the stall prevention function is C1-04.) 0 to 2 1 Effective when L3-05 is 1 or 2. Set as a percentage of the Inverter rated current. Usually setting is not necessary. The factory setting reduces the set values when the motor stalls. 30 to 200 160% Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A No No No 493H No A A No No No 494H 6-49 Changing Stall Prevention Level during Operation Using an Analog Input If you set H3-09 (Multi-function Analog Input Terminal A2 Function Selection) or H3-05 (Multi-function Analog Input Terminal A3 Function Selection) to 8 (stall prevention level during run), you can change the stall level during operation by setting H3-10 (Gain (Terminal A2)) and H3-11 (Bias (Terminal A2)) or H3-06 (Gain (Terminal A3)) and H3-07 (Bias (Terminal A3). The stall prevention level during operation enabled is the multi-function analog input terminal A2 or A3 input level or the set value in constant L3-06, whichever is the smaller. Stall prevention level during operation Multi-function analog input terminal A2, A3 input level (4 mA) (8.8 mA) (20 mA) Fig 6.39 Stall Prevention Level during Operation Using an Analog Input If the motor capacity is smaller than the Inverter capacity or the motor stalls when operating at the factory settings, lower the stall prevention level during operation. INFO Using Frequency Detection: L4-01 to L4-05 Set these constants when outputting one of the frequency agree or frequency detection signals from a multifunction output. When using flux vector control, the motor speed is detected. Related Constants Name Constant Number Display Speed agree detection level L4-01 L4-02 6-50 Spd Agree Level Speed agree detection width Spd Agree Width Description Setting Range Factory Setting Change during Operation Set the speed that you want to detect in Hz. The set speed is an absolute value, so the speed is detected in forward or reverse. 0.0 to 400.0 0.0 Hz Set the speed detection range in Hz. 0.0 to 20.0 2.0 Hz Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 499H No A A A A A 49AH Machine Protection Name Constant Number L4-03 Display Speed agree detection level (+/−) Spd Agree Lvl +− L4-04 Description Speed agree detection width (+/−) Spd Agree Width +− Setting Range Factory Setting Change during Operation Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 MEMO BUS Register Set the speed that you want to detect in Hz. Set positive values for forward, negative values for reverse. −400.0 0.0 Hz to +400.0 No A A A A A 49BH Set the speed detection range in Hz. 0.0 to 20.0 No A A A A A 49CH 2.0 Hz Constants and Output Signals User Constant Number Name Function Speed agree detection level Fref/Set Agree 1 Frequency Detection 1 Frequency Detection 2 Frequency Detection 5 L4-02 Speed agree detection width Fref/Fout Agree 1 Fref/Set Agree 1 Frequency Detection 1 Frequency Detection 2 Frequency Detection 5 L4-03 Speed agree detection level (+/-) Fref/Set Agree 2 Frequency Detection 3 Frequency Detection 4 Speed agree detection width (+/-) Fref/Fout Agree 2 Fref/Set Agree 2 Frequency Detection 3 Frequency Detection 4 L4-01 L4-04 Set the corresponding setting in the multi-function output (H2-01 to H2-05) to output the desired Fref/Fout Agree signal, Fref/Set Agree signal, or Frequency Detection signal. Function Setting Fref/Fout Agree 1 2 Fref/Set Agree 1 3 Frequency Detection 1 4 Frequency Detection 2 5 Fref/Fout Agree 2 13 Fref/Set Agree 2 14 Frequency Detection 3 15 Frequency Detection 4 16 Frequency Detection 5 36 6-51 Timing Chart for Frequency Detection Operation Related constant L4-01: Speed Agree Level L4-02: Speed Agree Width Fref/Fout Agree 1 Frequency reference Fref/Fout Agree L4-02 L4-03: Speed Agree Level +/− L4-04: Speed Agree Width +/− Fref/Fout Agree 2 Frequency reference L4-04 Output frequency or motor speed Output frequency or motor speed L4-02 Fref/Fout Agree 1 OFF ON OFF Fref/Fout Agree 2 (Multi-function output setting = 2) ON (Multi-function output setting = 13) Fref/Set Agree 1 (ON at the following conditions during frequency agree) Fref/Set Agree 2 +/− (ON at the following conditions during frequency agree) L4-02 L4-04 L4-03 L4-01 Fref/Set Agree Output frequency or motor speed put frequency motor speed L4-01 L4-02 f/Set Agree 1 OFF Fref/Set Agree 2 OFF ON ON (Multi-function output setting = 14) (Multi-function output setting = 3) Frequency (FOUT) Detection 1 (L4-01 > | Output frequency |) Frequency (FOUT) Detection 3 (L4-03 > Output frequency) L4-04 L4-02 L4-03 L4-01 Output frequency or motor speed Output frequency or motor speed L4-01 L4-02 Freq. Detection 1 ON Freq. Detection 3 OFF ON OFF (Multi-function output setting = 15) (Multi-function output setting = 4) Frequency (FOUT) Detection 2 (L4-01 < | Output frequency |) Frequency (FOUT) Detection 4 (L4-01 < Output frequency) L4-02 L4-04 L4-03 L4-01 Frequency Detection Output frequency or motor speed Output frequency or motor speed L4-01 L4-02 Freq. Detection 2 OFF Freq. Detection 4 ON Frequency (FOUT) Detection 5 (L4-01 < | Output frequency |) L4-02 L4-01 Output frequency or motor speed L4-01 L4-02 Freq. Detection 5 OFF ON (Multi-function output setting = 36) 6-52 OFF ON (Multi-function output setting = 16) (Multi-function output setting = 5) OFF during baseblock Machine Protection Detecting Motor Torque If an excessive load is placed on the machinery (overtorque) or the load is suddenly lightened (undertorque), you can output an alarm signal to multi-function output terminal M1-M2, P1-PC, P2-PC, P3-C3, or P4-C4. To use the overtorque/undertorque detection function, set B, 17, 18, 19 (overtorque/undertorque detection NO/ NC) in one of the following constants: H2-01 to H2-05 (multi-function output terminals M1-M2, P1-PC, P2PC, P3-C3, and P4-C4 function selection). The overtorque/undertorque detection level is the current level (Inverter rated output current 100%) in V/f control, and the motor torque (motor rated torque 100%) in vector control. Related Constants Name Constant Number Display Torque detection selection 1 L6-01 Torq Det 1 Sel L6-02 Torque detection level 1 Torq Det 1 Lvl Description Setting Range Factory Setting Change during Operation 0: Overtorque/undertorque detection disabled. 1: Overtorque detection only with speed agreement; operation continues after overtorque (warning). 2: Overtorque detected continuously during operation; operation continues after overtorque (warning). 3: Overtorque detection only with speed agreement; output stopped upon detection (protected operation). 4: Overtorque detected continuously during operation; output stopped upon detection (protected operation). 5: Undertorque detection only with speed agreement; operation continues after overtorque (warning). 6: Undertorque detected continuously during operation; operation continues after overtorque (warning). 7: Undertorque detection only with speed agreement; output stopped upon detection (protected operation). 8: Undertorque detected continuously during operation; output stopped upon detection (protected operation). 0 to 8 0 Open-loop vector control: Motor rated torque is set as 100%. V/f control: Inverter rated current is set as 100%. 0 to 300 150% Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 4A1H No A A A A A 4A2H 6-53 Name Constant Number L6-03 L6-04 Display Torque detection time 1 Torq Det 1 Time Torque detection selection 2 Torq Det 2 Sel L6-05 Torque detection level 2 Torq Det 2 Lvl L6-06 Torque detection time 2 Torq Det 2 Time Setting Range Factory Setting Change during Operation Sets the overtorque/undertorque detection time in 1-second units. 0.0 to 10.0 0.1 s Multi-function output for overtorque detection 1 is output to multi-function contact output when overtorque detection 1 NO or overtorque detection 1 NC is selected. Multi-function output for overtorque detection 2 is output to multi-function contact output when overtorque detection 2 NO or overtorque detection 2 NC is selected. 0 to 8 Description Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 4A3H 0 No A A A A A 4A4H 0 to 300 150% No A A A A A 4A5H 0.0 to 10.0 0.1 s No A A A A A 4A6H Multi-function Output (H2-01 to H2-05) Control Methods Setting Value 6-54 Function V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 B Overtorque/undertorque detection 1 NO (NO contact: Overtorque/undertorque detection at ON) Yes Yes Yes Yes Yes 17 Overtorque/undertorque detection 1 NC (NC Contact: Overtorque/undertorque detection at OFF) Yes Yes Yes Yes Yes 18 Overtorque/undertorque detection 2 NO (NO Contact: Overtorque/undertorque detection at ON) Yes Yes Yes Yes Yes 19 Overtorque/undertorque detection 2 NC (NC Contact: Overtorque/undertorque detection at OFF) Yes Yes Yes Yes Yes Machine Protection L6-01 and L6-04 Set Values and LCD Indications The relationship between alarms displayed by the Digital Operator when overtorque or undertorque is detected, and the set values in L6-01 and L6-04, is shown in the following table. Set Value LCD Indications Overtorque/ Overtorque/ Undertorque Undertorque Detection 1 Detection 2 Function 0 Overtorque/undertorque detection disabled. - - 1 Overtorque detection only with speed matching; operation continues after overtorque (warning). OL3 flashes OL4 flashes 2 Overtorque detected continuously during operation; operation continues after overtorque (warning). OL3 flashes OL4 flashes 3 Overtorque detection only with speed matching; output stopped upon detection (protected operation). OL3 lit OL4 lit 4 Overtorque detected continuously during operation; output stopped upon detection (protected operation). OL3 lit OL4 lit 5 Undertorque detection only with speed matching; operation continues after overtorque (warning). UL3 flashes UL4 flashes 6 Undertorque detected continuously during operation; operation continues after overtorque (warning). UL3 flashes UL4 flashes 7 Undertorque detection only with speed matching; output stopped upon detection (protected operation). UL3 lit UL4 lit 8 Undertorque detected continuously during operation; output stopped upon detection (protected operation). UL3 lit UL4 lit Setting Example The following diagram shows the time chart for overtorque and undertorque detection. • Overtorque Detection Motor current (output torque) * L6-02 or L6-05 Overtorque detection 1 NO or overtorque detection 2 NO L6-03 or L6-06 ON * L6-03 or L6-06 ON * Overtorque detection disabled band is approximately 10% of the Inverter rated output current (or motor rated torque). 6-55 • Undertorque Detection Motor current (output torque) * L6-02 or L6-05 Undertorque detection 1 NO or Undertorque detection 2 NO L6-03 or L6-06 ON L6-03 or L6-06 ON * The undertorque detection disabled margin is approximately 10% of the Inverter rated output current (or motor rated torque) Changing Overtorque and Undertorque Detection Levels Using an Analog Input If you set constant H3-09 (Multi-function Analog Input Terminal A2 Function Selection) or H3-05 (Multifunction Analog Input Terminal A3 Function Selection) to 7 (overtorque/undertorque detection level), you can change the overtorque/undertorque detection level. If you change the overtorque/undertorque detection level using the multi-function analog input, only overtorque/undertorque detection level 1 will be enabled. The following diagram shows the overtorque/undertorque detection level using an analog input. Detection level Multi-function analog input terminal A2, A3 input level (4 mA) (20 mA) Fig 6.40 Overtorque/Undertorque Detection Level Using an Analog Input Multi-Function Analog Input (H3-05, H3-09) Control Methods Setting Value 7 6-56 Function Overtorque/undertorque detection level Contents (100%) Motor rated torque for vector control Inverter rated output current for V/f control V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 Yes Yes Yes Yes Yes Machine Protection Motor Overload Protection You can protect the motor from overload using the Inverter's built-in electronic thermal overload relay. Related Constants Name Constant Number Display Motor rated current E2-01 Motor Rated FLA Motor 2 rated current E4-01 Motor Rated FLA Motor protection selection L1-01 MOL Fault Select Motor protection time constant L1-02 MOL Time Const Description Setting Range Factory Setting Change during Operation Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 MEMO BUS Register Sets the motor rated current in 1 A units. These set values will become the 0.32 to reference values for motor protec1.90 A 6.40 *1 tion, torque limits and torque con*2 trol. This constant is automatically set during autotuning. No Q Q Q Q Q 30EH Sets the motor rated current in 1 A units. These set values will become the reference values for motor protection, torque limits and torque control. This constant is automatically set during autotuning. No A A A A A 321H 0.32 to 6.40 1.90 A *1 *3 Sets whether the motor overload function is enabled or disabled at electric thermal overload relay. 0: Disabled 1: General-purpose motor protection 2: Inverter motor protection 3: Vector motor protection In some applications when the Inverter power supply is turned off, the thermal value is reset, so even if this constant is set to 1, protection may not be effective. When several motors are connected to one Inverter, set to 0 and ensure that each motor is installed with a protection device. 0 to 3 1 No Q Q Q Q Q 480H Sets the electric thermal detection time in seconds units. Usually setting is not necessary. The factory setting is 150% overload for one minute. When the motor's overload resistance is known, also set the overload resistance protection time for when the motor is hot started. 0.1 to 5.0 1.0 min No A A A A A 481H * 1. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. * 2. The setting range is from 10% to 200% of the Inverter rated output current. The value for a 200 V Class Inverter for 0.4 kW is given. For the motor no-load current, set E2-03 to a value less than that of E2-01. * 3. The setting range is from 10% to 200% of the Inverter rated output current. The value for a 200 V Class Inverter for 0.4 kW is given. 6-57 Multi-Function Outputs (H2-01 to H2-05) Control Methods Setting Value 1F Function Motor overload (OL1, including OH3) pre-alarm (ON: 90% or more of the detection level) V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 Yes Yes Yes Yes Yes Setting Motor Rated Current Set the rated current value on the motor nameplate in constants E2-01 (for motor 1) and E4-01 (for motor 2). This set value is the electronic thermal base current. Setting Motor Overload Protection Characteristics Set the overload protection function in L1-01 according to the applicable motor. The induction motor's cooling abilities differ according to the speed control range. Consequently, you must select the electronic thermal protection characteristics to match the applicable motor's tolerance load characteristics. The following table shows the motor type and tolerance load characteristics. L1-01 Set Value Motor Type Tolerance Load Characteristics Cooling Ability Electronic Thermal Operation (at 100% Motor Load) Rated rotation speed = 100% speed 1 General-purpose motor (standard motor) Torque (%) Short time 60 s. Continuous Frame number Max. speed Frame number Max. speed of 200 of 160 MJ to 160 LJ min. LJ min. Frame number Max. speed of 132 MJ Use this motor for operations using a commercial power supply. This motor construction yields best cooling effect when operating at 50/ 60 Hz. When operating continuously at 50/60 Hz or less, motor overload detection (OL1) is detected. The Inverter outputs the error contact, and the motor coasts to a stop. This motor yields a cooling effect even when operating at low speeds (approx. 6 Hz). Operates continuously at 6 to 50/60 Hz. Rotation speed (%) 2 Inverter motor (constant torque) (1:10) Rated rotation speed = 100% speed Torque (%) Short time 60 Continuous Frame number Max. speed of 200 LJ min. Frame number Max. speed of 160 MJ to 180 LJ Frame number Max. speed of 132 MJ Rotation speed (%) 6-58 Machine Protection L1-01 Set Value Motor Type Tolerance Load Characteristics 3 Vector motor (1:100) Electronic Thermal Operation (at 100% Motor Load) Rated rotation speed = 100% speed Torque (%) Short time 60 s. Cooling Ability Continuous Frame number Max. speed of 200 LJ min. Frame number Max. speed of 160 MJ to 180 LJ Frame number Max. speed of 132 MJ This motor yields a cooling effect even Operates continuously at when operating at 0.6 to 60 Hz. extremely low speeds (approx. 0.6 Hz). Rotation speed (%) Setting Motor Protection Operation Time Set the motor protection operation time in L1-02. If, after operating the motor continuously at the rated current, a 150% overload is experienced, set the (hot start) electronic thermal protection operation time. The factory setting is resistance to 150% for 60 seconds. The following diagram shows an example of the characteristics of the electronic thermal protection operation time (L1-02 = 1.0 min., operation at 60 Hz, general-purpose motor characteristics, when L1-01 is set to 1) Operating time (min.) Cold start Hot start Motor current (%) E2-01 is set to 100% Fig 6.41 Motor Protection Operation Time Setting Precautions • If multiple motors are connected to one Inverter, set constant L1-01 to 0 (disabled). To protect the motor, install a thermal relay in the motor power cable, and perform overload protection on each motor. • With applications where the power supply is often turned ON and OFF, there is a risk that the circuit cannot be protected even if this constant has been set to 1 (enabled), because the thermal value will be reset. • To detect overloads in good time, set the set value in constant L1-02 to a low setting. • When using a general-purpose motor (standard motor), the cooling ability will be lowered by f1/4 (fre- quency). Consequently, the frequency may cause motor overload protection (OL1) to occur, even below the rated current. If operating using the rated current at a low frequency, use a special motor. 6-59 Setting the Motor Overload Pre-Alarm If the motor overload protection function is enabled (i.e., L1-01 is set to other than 0) and you set H2-01 to H2-05 (multi-function output terminals M1-M2, P1-PC, P2-PC, P3-C3, and P4-C4 function selection) to 1F (motor overload OL1 pre-alarm), the motor overload pre-alarm will be enabled. If the electronic thermal value reaches minimum 90% of the overload detection level, the output terminal that has been set will be turned ON. Motor Overheating Protection Using PTC Thermistor Inputs Perform motor overheating protection using the thermistor temperature resistance characteristics of the PTC (Positive Temperature Coefficient) built into the windings of each motor phase. Related Constants Name Constant Number Display Alarm operation selection during motor overheating L1-03 MOL Thm Input Motor overheating operation selection L1-04 MOL Filter Time L1-05 6-60 Description Setting Range Factory Setting Change during Operation Set H3-09 to E and select the operation when the input motor temperature (thermistor) input exceeds the alarm detection level (1.17 V). 0: Decelerate to stop using the deceleration time in C1-02. 1: Coast to stop 2: Emergency stop using the deceleration time in C1-09. 3: Continue operation (H3 on the Operator flashes). 0 to 3 3 Set H3-09 to E and select the operation when the motor temperature (thermistor) input exceeds the operation detection level (2.34 V). 0: Decelerate to stop using the deceleration time in C1-02. 1: Coast to stop 2: Emergency stop using the deceleration time in C1-09. 0 to 2 1 Motor temperature input filter Set H3-09 to E and set the primary delay time constant for time constant motor temperature (thermistor) MOL Filter inputs in seconds. Time 0.00 to 0.20 s 10.00 Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 482H No A A A A A 483H No A A A A A 484H Machine Protection PTC Thermistor Characteristics The following diagram shows the characteristics of the PTC thermistor temperature to the resistance value. Class F 150°C Resistance (ohms) Class H 180°C 1330 Tr: Temperature threshold value 550 Tr Tr 5 Tr Temperature Tr+5 Fig 6.42 PTC Thermistor Temperature-Resistance Value Characteristics Operation during Motor Overheating Set the operation if the motor overheats in constants L1-03 and L1-04. Set the motor temperature input filter time constant in L1-05. If the motor overheats, the OH3 and OH4 error codes will be displayed on the Digital Operator. Error Codes If the Motor Overheats Error Code Details OH3 Inverter stops or continues to operate, according to the setting in L1-03. OH4 Inverter stops according to the setting in L1-04. By setting H3-09 (Multi-function Analog Input Terminal A2 Function Selection) or H3-05 (Multi-function Analog Input Terminal A3 Function Selection) to E (Motor temperature input), you can detect alarm OH3 or OH4 using the PTC temperature-resistance characteristics, and protect the motor. The terminal connections are shown in the following diagram. Set H3-08〔Signal level selection (terminal A2)〕(H3-04 when A3 is used) to 0 (0 to + 10 V). Inverter Multi-function contact input Multi-function contact output Fault contact output Branch resistance 18 kΩ A2, A3 (0-10 V) PTC thermistor Multi-function PHC output * When using terminal A2, set DIP switch S1-2 to OFF (0 to 10 V). Fig 6.43 Mutual Connections During Motor Overheating Protection 6-61 Limiting Motor Rotation Direction If you set motor reverse rotation prohibited, a Reverse Run Command will not be accepted even if it is input. Use this setting for applications in which reverse motor rotation can cause problems (e.g., fans, pumps, etc.) Related Constants Name Constant Number b1-04 Display Prohibition of reverse operation Reverse Oper 6-62 Description 0: Reverse enabled 1: Reverse disabled Setting Range Factory Setting Change during Operation 0 or 1 0 No Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A MEMO BUS Register 183H Continuing Operation Continuing Operation This section explains functions for continuing or automatically restarting Inverter operation using speed search even if an error occurs. Restarting Automatically After Power Is Restored Even if a temporary power loss occurs, you can perform estimated/current detection speed search using the speed search function (b3-01) and restart the Inverter automatically after power is restored to continue motor operation. To restart the Inverter after power has been restored, set L2-01 to 1 or 2. Make settings of L2-01 to L2-05 and b3-01 for related details of restarting. • If L2-01 is set to 1: when power is restored within the time set in L2-02, the Inverter will restart. If the time set in L2-02 is exceeded, alarm UV1 (main circuit undervoltage) will be detected. • If L2-01 is set to 2: when the main power supply is restored while the control power supply (i.e., power supply to the control panel) is backed up, the Inverter will restart. Consequently, alarm UV1 (main circuit undervoltage) will not be detected. Related Constants Name Constant Number Display Momentary power loss detection L2-01 PwrL Selection L2-02 Factory Setting Change during Operation 0: Disabled [main circuit undervoltage (UV1) detection] 1: Enabled [Restarted when the power returns within the time for L2-02. When L2-02 is exceeded, main circuit undervoltage (UV1) is detected.] 2: Enabled while CPU is operating. [Restarts when power returns during control operations. Does not detect main circuit undervoltage (UV1).] 0 to 2 0 0 to 25.5 0.1 s 0.1 to 5.0 0.2 s Momentary power loss ride- Ridethrough time, when Momentary Power Loss Selection (L2thru time 01) is set to 1, in units of seconds. PwrL Ridethru t Min. baseblock time L2-03 Description Setting Range PwrL Baseblock t Sets the Inverter's minimum baseblock time in units of one second, when the Inverter is restarted after power loss ridethrough. Sets the time to approximately 0.7 times the motor secondary circuit time constant. When an overcurrent or overvoltage occurs when starting a speed search or DC injection braking, increase the set values. *1 *1 Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 485H No A A A A A 486H No A A A A A 487H 6-63 Name Constant Number Factory Setting Sets the time required to return the Inverter output voltage to normal voltage at the completion of a speed search, in units of one second. Sets the time required to recover from 0 V to the maximum voltage. 0.0 to 5.0 0.3 s Display Voltage recovery time L2-04 Description Setting Range PwrL V/F Ramp t Undervoltage detection level L2-05 PUV Det Level Sets the main circuit undervoltage (UV) detection level (main circuit DC voltage) in V units. Usually setting is not necessary. Insert an AC reactor in the Inverter input side to lower the main circuit undervoltage detection level. 150 to 210 *2 *1 190 V *2 Change during Operation Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 488H No A A A A A 489H Note Attach a Backup Capacitor Unit for Momentary Power Loss if compensation for power interruptions of up to 2.0 seconds is required for 200 V/400 V Class Inverters with outputs of 0.4 to 7.5 kW. * 1. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. * 2. These values are for a 200 V Class Inverter. For a 400 V Class Inverter, double the values. Setting Precautions • Error output signals are not output during momentary power loss recovery. • To continue Inverter operation after power has been restored, make settings so that Run Commands from the control main circuit terminal are stored even while power is suspended. • If the momentary power loss operation selection is set to 0 (Disabled), when the momentary power loss exceeds 15 ms during operation, alarm UV1 (main circuit undervoltage) will be detected. Speed Search The speed search function finds the actual speed of the motor that is rotating using inertia, and then starts smoothly from that speed. When restoring power after a temporary power loss, the speed search function switches connection from the commercial power supply, and then restarts the fan that is rotating using inertia. Speed search will be performed in the following cases. • When Momentary power loss detection (L2-01) is set to 1 or 2 (Enabled) and power is restored after IMPORTANT a momentary power loss. • When Number of auto restart attempts (L5-01) is set from 1 to 10 and the auto restart is performed after a fault. • Multi-function contact inputs (H1-) are set to External search command (61, 62, or 64) and the command is sent. • Multi-function contact inputs (H1-) are set to External baseblock (8 or 9) and the release command is sent. The selected speed search type in b3-01, speed calculation or current detection, will be performed. 6-64 Continuing Operation Related Constants Name Constant Number Display Speed search selection (current detection or speed calculation) b3-01 SpdSrch at Start Description Setting Range Change Factory during Setting Operation Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A No A 191H No A No A No A 192H Enables/disables the speed search function for the Run Command and sets the speed search method. 0:Disabled, speed calculation 1: Enabled, speed calculation 2: Disabled, current detection 3: Enabled, current detection Speed Calculation: When the search is started, the motor speed is calculated and acceleration/deceleration is performed from the calculated speed to the specified frequency (motor direction is also searched). 0 to 3 2 *1 Current Detection: The speed search is started from the frequency when power was momentarily lost and the maximum frequency, and the speed is detected at the search current level. b3-02 Speed search operating current (current detection) SpdSrch Current b3-03 Speed search deceleration time (current detection) SpdSrch Dec Time b3-05 Speed search wait time (current detection or speed calculation) Search Delay b3-10 Speed search detection compensation gain (speed calculation) Srch Detect Comp Sets the speed search operation current as a percentage, taking the Inverter rated current as 100%. Not usually necessary to set. When restarting is not possible with the factory settings, reduce the value. 0 to 200 Sets the output frequency deceleration time during speed search in 1-second units. Set the time for deceleration from the maximum output frequency to the minimum output frequency. 0.1 to 10.0 2.0 s No A No A No No 193H Sets the magnetic contactor operating delay time when there is a magnetic contactor on the output side of the Inverter. When a speed search is performed after recovering from a momentary power loss, the search operation is delayed by the time set here. 0.0 to 20.0 0.2 s No A A A A A 195H Operation restarts at a speed obtained by multiplying the speed from the speed search by the compensation gain. 1.00 to Increase this setting if overvolt1.20 ages occur when speed search is performed after a long baseblock, for example, in searches at startup. 1.10 No A No A No A 19AH 100% *1 6-65 Name Constant Number b3-13 b3-14 Display b3-17 *2 b3-18 *2 b3-19 *2 Speed search retrial current level SrchRestart Lv1 Speed search retrial detection time SrchRestart Time Number of speed search retrials Num of SrchRestr Min. baseblock time L2-03 PwrL Baseblock t Voltage recovery time L2-04 PwrL V/F Ramp t Change during Operation 0.1 to 2.0 1.0% Control Methods V/f Flux Vector Open Loop Vector 2 No No No No No A 19DH 1 No A A A No A 19EH 0 to 200 150% No A No A No A 1F0H Sets the time for detection in a speed search retrial in units of seconds. 0.00 to 1.00 0.10 s No A No A No A 1F1H Sets the number of times that a speed search can be retried. 0 to 10 0 No A No A No A 1F2H Sets the Inverter's minimum baseblock time in units of one second, when the Inverter is restarted after power loss ridethrough. Sets the time to approximately 0.7 times the motor secondary circuit time constant. When an overcurrent or overvoltage occurs when starting a speed search or DC injection braking, increase the set values. 0.1 to 5.0 0.2 s No A A A A A 487H Sets the time required to return the Inverter output voltage to normal voltage at the completion of a speed search, in units of one second. Sets the time required to recover from 0 V to the maximum voltage. 0.0 to 5.0 0.3 s No A A A A A 488H 0: Disabled (operates with specified rotation direction) 0 or 1 1: Enabled (operates with rotation direction found by search) Sets the current level to retry a speed search as a percentage, taking the Inverter rated current as 100%. *3 *3 * 1. The factory setting will change when the control method is changed. The open-loop vector 1 control factory settings are given. * 2. Applicable for G7-Series Inverters with software versions PRG: 1039 or later. * 3. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. 6-66 MEMO BUS Register Open Loop Vector 1 Sets the proportional gain (PI control) of the speed estimator during speed search taking the setting of N4-08 to be equivalent to a setting of 1.0. Usually, there is no need to change this setting. If, however, Srch Est P Gain the load inertia is large and overvoltages occur during the search, reduce this setting. Bidir Search Sel Factory Setting V/f with PG Description Proportional gain of the speed estimator during speed search Rotation direction search selection Setting Range Continuing Operation Multi-function Contact Inputs (H1-01 to H1-10) Control Methods Setting Value Function V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 61 External search command 1 (ON: Speed search from maximum output frequency) Yes No Yes No Yes 62 External search command 2 (ON: Speed search from set frequency) Yes No Yes No Yes Setting Precautions • When both external search commands 1 and 2 are set for the multi-function contact terminals, an OPE03 (invalid multi-function input selection) operation error may occur. Set either external search command 1 or external search command 2. • If speed search during startup is selected when using V/f control with PG, the Unit will start from the fre- quency detected by PG. • If performing speed search using external search commands, add an external sequence so that the period when the Run Command and external search command are both ON is at the very least the Minimum Baseblock Time (L2-03). • If the Inverter output is equipped with a contact, set the contact operation delay time in the Speed Search Wait Time (b3-05). The factory setting is 0.2 s. When not using the contact, you can reduce the search time by making the setting 0.0 s. After waiting for the speed search wait time, the Inverter starts the speed search. • Constant b3-02 is a current detection speed search (current detection level for search completion). When the current falls below the detection level, the speed search is viewed as completed, and the motor accelerates or decelerates to the set frequency. If a motor overload (OL1) or an Inverter overload (OL2) occurs and the motor cannot restart, lower the set value. • If an overcurrent (OC) is detected when using speed search after recovery following a power loss, lengthen the Minimum Baseblock Time (L2-03). • If a main circuit over voltage (OV) is detected when using a current detection speed search after a momen- tary power loss, lengthen the Speed search detection time (b3-03). Application Precautions for Speed Searches Using Estimated Speed • When using V/f control with or without a PG, always perform stationary autotuning for only line-to-line resistance before using speed searches based on estimated speeds. • When using vector control, always perform rotational or stationary autotuning (not stationary autotuning for line-to-line resistance only) before using speed searches based on estimated speeds. • If the cable length between the motor and Inverter is changed after autotuning has been performed, per- form stationary autotuning for line-to-line resistance only again. The motor will not operate when stationary autotuning or stationary autotuning for line-to-line resistance only is performed. IMPORTANT 6-67 Speed Search Selection Set whether to enable or disable speed search at startup, and set the type of speed search (estimated speed or current detection) using setting b3-01. To perform speed search when inputting the Run Command, set b3-01 to 1 or 3. Search Name Search Method Estimated Speed (b3-01 = 0 or 1) Current Detection (b3-01 = 2 or 3) Estimates the motor speed when the search starts, and accelerates and decelerates from the estimated speed to the set frequency. You can also search including direction of motor rotation. Starts speed search from the frequency when the temporary power loss was detected, or from the highest frequency, and performs speed detection at the current level during the search. External search command 1 and external External Speed Search search command 2 become the same operation, Command estimating the motor speed and starting the search from the estimated speed. Application Precautions External speed search command 1: Starts speed search from the maximum output frequency. External speed search command 2: Starts speed search from the frequency reference set before the search command. Cannot be used multi-motor drives, motors two In control method without PG, the motor may or more frames smaller than the Inverter capacaccelerate suddenly with light loads. ity, and high-speed motors (130 Hz min.) Estimated Speed Search (b3-01 = 0 or 1) The time chart for estimated speed searches is shown below. Search at Startup (b3-01 = 1) The time chart when speed search at startup or external speed search command of multi-function inputs has been selected is shown below. OFF ON Set frequency reference Run Command Output frequency Start using speed detected b3-02 Output current 1.0 s * Lower limit set using Speed Search Wait Time (b3-05). Minimum baseblock time (L2-03) × 0.7* Note: If the stopping method is set to coast to stop, and the Run Command turns ON in a short time, the operation may be the same as the search in case 2. Fig 6.44 Speed Search at Startup (Estimated Speed) 6-68 Continuing Operation Speed Search after Short Baseblock (during Power Loss Recovery, etc.) (b3-01 = 0) The time chart when the Inverter operation is restarted after power has been restored is shown below. • Loss Time Shorter Than the Minimum Baseblock Time (L2-03) AC power supply ON OFF Start using speed detected Set frequency reference Output frequency Output current 10 ms Minimum baseblock time (L2-03) x 0.75*1 *2 *1 Baseblock time may be reduced by the output frequency immediately before the baseblock. *2 After AC power supply recovery, motor waits for the minimum Speed Search Wait Time (b3-05). Fig 6.45 Speed Search after Baseblock (When Estimated Speed: Loss Time Is Set in L2-03) • Loss Time Longer Than the Minimum Baseblock Time (L2-03) AC power supply ON OFF Start using speed detected Set frequency reference Output frequency Output current 10 ms Minimum baseblock time (L2-03) Speed Search Wait Time (b3-05) Fig 6.46 Speed Search After Baseblock (Estimated Speed: Loss Time > L2-03) 6-69 Current Detection Speed Search (b3-01 = 2 or 3) The time charts for current detection speed search is shown below. Speed Search at Startup (b3-01 = 3) The time chart when speed search at startup or external speed search command is selected is shown below. Run Command OFF ON Deceleration time set in b3-03 Maximum output frequency or set frequency Set frequency reference Output frequency b3-02 Output current Minimum baseblock time (L2-03) * * Lower limit is set using Speed Search Time (b3-05). Fig 6.47 Speed Search at Startup (Using Current Detection) Speed Search after Short Baseblock (b3-01 = 2) The time chart when the Inverter operation is restarted after power has been restored is shown below. • Loss Time Shorter Than Minimum Baseblock Time AC power supply ON OFF Output frequency before power loss Set frequency Deceleration reference time set in b3-03 Output frequency b3-02 speed search operating current Output current *1 Baseblock time may be reduced by the output frequency immediately before baseblock. *2 After AC power supply recovery, motor waits for the minimum Speed Search Wait Time (b2-03). Minimum baseblock time (L2-03) *1 *2 Fig 6.48 Speed Search After Baseblock (Current Detection: Loss Time < L2-03) • Loss Time Longer Than Minimum Baseblock Time AC power supply ON OFF Output frequency before power loss Deceleration speed set in b3-03 Set frequency reference Output frequency b3-02 Speed search operating time Output current Speed search wait time (b3-05) Minimum baseblock time (L2-03) Fig 6.49 Speed Search After Baseblock (Current Detection: Loss Time > L2-03) 6-70 Continuing Operation Continuing Operation at Constant Speed When Frequency Reference Is Lost The frequency reference loss detection function continues operation using 80% speed of the frequency reference before loss when the frequency reference using a master speed analog input* is reduced 90% or more in 400 ms. When the error signal during frequency reference loss is output externally, set H2-01 to H2-05 (multi-function contact output terminal M1-M2, P1-PC, P2-PC, P3-C3, and P4-C4 function selection) to C (frequency reference lost). * Frequency references using the following master speed analog inputs are used to detect a frequency loss. • Analog input using terminal A1 • Analog input using terminal A2 when H3-09 (Multi-function analog input terminal A2 function selection) is set to 0 (Add to terminal A1). Related Constants Name Constant Number Display Operation when frequency reference is missing L4-05 Ref Loss Sel Description Setting Range 0: Stop (Operation follows the frequency reference.) 1: Operation at 80% speed continues. (At 80% of speed before the frequency reference was lost) Frequency reference is lost: Frequency reference dropped over 90% in 400 ms. 0 or 1 Change Factory during Setting Operation 0 No Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A MEMO BUS Register 49DH 6-71 Restarting Operation After Transient Fault (Auto Restart Function) If an Inverter fault occurs during operation, the Inverter will perform self-diagnosis. If no fault is detected, the Inverter will automatically restart using the speed search function (b3-01). This is called the auto restart function. Set the number of auto restarts in constant L5-01. A fault reset is attempted every 5 ms after a fault occurs and minimum baseblock time has passed. The number of auto restarts is counted when the Inverter attempts a fault reset and restarts operation. The protection function will operate if a fault continues to occur after auto restarting the number of times set in L5-01. The auto restart function can be applied to the following faults. If a fault not listed below occurs, the protection function will operate and the auto restart function will not. • OC (Overcurrent) • RH (Braking resistor overheated) • GF (Ground fault) • RR (Braking transistor error) • PUF (Fuse blown) • OL1 (Motor overload) • OV (Main circuit overvoltage) • OL2 (Inverter overload) • UV1 (Main Circuit Undervoltage, Main Circuit Magnetic Contactor Operation Failure)* • OH1 (Motor overheat) • PF (Main circuit voltage fault) • OL3 (Overtorque) • LF (Output phase failure) • OL4 (Overtorque) * When L2-01 is set to 1 or 2 (continue operation during momentary power loss) Auto Restart External Outputs To output auto restart signals externally, set H2-01 to H2-05 (multi-function contact output terminals M1-M2, P1-PC, P2-PC, P3-C3, and P4-C4 function selection) to 1E (restart enabled). Related Constants Name Factory Setting Change during Operation L5-01 Number of auto Sets the number of auto restart restart attempts attempts. Automatically restarts after a fault 0 to 10 Num of and conducts a speed search from Restarts the run frequency. 0 L5-02 Sets whether a fault contact outAuto restart operation selec- put is activated during fault restart. tion 0: Not output (Fault contact is not activated.) Restart Sel 1: Output (Fault contact is activated.) 0 Constant Number Display Description Setting Range 0 or 1 Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 49EH No A A A A A 49FH Application Precautions • The number of auto restarts count is reset under the following conditions: After auto restart, normal operation has continued for 10 minutes. After the protection operation has been performed, and the fault has been verified, and an fault reset has been input. After the power supply is turned OFF, and then ON again. • Do not use the auto restart function with variable loads. 6-72 Continuing Operation Operation Selection After Cooling Fan Fault Use the constant setting to select the operation of the motor after a cooling fan fault occurs. This function can be used for times when a motor should not be stopped quickly (with an emergency stop.) A cooling fan equipped for 200 V Class Inverters of 7.5 kW, 15 kW, and 30 to 110 kW, and 400 V Class Inverters of 5.5 to 15 kW and 55 to 300 kW. Related Constants Name Constant Number L8-32* Description Display OH1 detection of Inverter’ s cooling fan OH1 Detect Sel 0: Disabled (FAN minor fault detection) 1: Enabled (OH1 major fault detection) Setting Range Factory Setting Change during Operation 0 or 1 1 No Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A MEMO BUS Register 4E2H * Applicable for G7-Series Inverters with software versions PRG:1038 or later. The following table describes the operation of the motor and the display of the Digital Operator in accordance with the settings of the L8-32 if a cooling fan fault occurred. Setting Value Fault Cooling Fin Overheating 0 1 Digital Operator OH1 (lit) Motor Operation Coast to a stop Multi-function Contact Output Fault * Minor fault Inverter’s Cooling Fan Fault FAN (blink) Continue operation Cooling Fin Overheating OH (lit) Coast to a stop Fault Inverter’s Cooling Fan Fault OH1 (lit) Coast to a stop Fault * If L8-32 is set to 0, the motor will continue running even if a cooling fan fault occurred. However, the Inverter rated output current and the overload capacity will be reduced. The rated output current will be reduced to 80% if the normal rated output current is 100%, and the overload capacity will be reduced to the values as follows. When CT is selected: 100% per every 3 minutes, 150% per every 15 seconds When VT is selected: 100% per every 30 seconds, 120% per every 10 seconds IMPORTANT If L8-32 is set to 0, be sure to set H2-01 to H2-03 multi-function contact outputs to 10 (minor fault) or to 3D (Inverter’s cooling fan fault.) If a cooling fan fault occurs, stop the Inverter immediately and replace the cooling fan. If the Inverter continues to run while a cooling fan fault occurs, the Inverter’s cooling ability will be affected and the Inverter’s internal temperature will increase and shorten the Inverter’s life. During a cooling fan fault, the cooling fan stops for about 3 seconds every minute (interval operation.) 6-73 Inverter Protection This section explains the functions for protecting the Inverter and the braking resistor. Performing Overheating Protection on Mounted Braking Resistors Perform overheating protection on Inverter-mounted braking resistors (Model: ERF-150WJ ). When overheating in a mounted braking resistor is detected, an alarm RH (Mounted braking resistor overheating) is displayed on the Digital Operator, and the motor coasts to a stop. Related Constants Name Constant Number Display L8-01 Protect selection for internal DB resistor (Type ERF) DB Resistor Prot Description 0: Disabled (no overheating protection) 1: Enabled (overheating protection) Setting Range 0 or 1 Change Factory during Setting Operation 0 No Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A MEMO BUS Register 4ADH Multi-function Contact Outputs (H2-01 to H2-05) Control Methods Setting Value D Function Braking resistor fault (ON: Resistor overheat or braking transistor fault) V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 Yes Yes Yes Yes Yes The most likely causes of RH (Mounted braking resistor overheating) being detected are that the deceleration time is too short or that the motor regeneration energy is too large. In these cases, lengthen the deceleration time or replace the Braking Resistor Unit with one with a higher breaking capacity. INFO 6-74 Inverter Protection Reducing Inverter Overheating Pre-Alarm Warning Levels The Inverter detects the temperature of the cooling fins using the thermistor, and protects the Inverter from overheating. You can receive Inverter overheating pre-alarms in units of 1°C. The following overheating pre-alarm warnings are available: Stopping the Inverter as error protection, and continuing operation, with the alarm OH (Radiation fins overheating) on the Digital Operator flashing. Related Constants Name Constant Number Display Overheat prealarm level L8-02 OH Pre-Alarm Lvl Operation selection after overheat prealarm L8-03 OH Pre-Alarm Sel Description Setting Range Factory Setting Change during Operation Sets the detection temperature for the Inverter overheat detection pre-alarm in °C. The pre-alarm detects when the heatsink temperature reaches the set value. 50 to 130 95 °C* Sets the operation for when the Inverter overheat pre-alarm goes ON. 0: Decelerate to stop in deceleration time C1-02. 1: Coast to stop 2: Fast stop in fast-stop time C109. 3: Continue operation (Monitor display only.) A fault will be given in setting 0 to 2 and a minor fault will be given in setting 3. 0 to 3 3 Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 4AEH No A A A A A 4AFH * The factory setting depends upon the Inverter capacity. The value for 200 V Class Inverter of 0.4 kW is given. 6-75 Input Terminal Functions This section explains input terminal functions, which set operating methods by switching functions for the multi-function contact input terminals (S3 to S12). Temporarily Switching Operation between Digital Operator and Control Circuit Terminals You can switch the Inverter Run Command inputs and frequency reference inputs between local (i.e., Digital Operator) and remote (input method using b1-01 and b1-02). You can switch between local and remote by turning ON and OFF the terminals if an output from H1-01 to H1-10 (multi-function contact input terminal S3 to S12 function selection) has been set to 1 (local/remote selection). To set the control circuit terminals to remote, set b1-01 and b1-02 to 1 (Control circuit terminals). Related Constants Name Constant Number Display Reference selection b1-01 Reference Source Operation method selection b1-02 Run Source Description Setting Range Factory Setting Change during Operation Set the frequency reference input method. 0: Digital Operator 1: Control circuit terminal (analog input) 2: MEMOBUS communications 3: Option board 4: Pulse train input 0 to 4 1 Set the Run Command input method. 0: Digital Operator 1: Control circuit terminal (sequence input) 2: MEMOBUS communications 3: Option board 0 to 3 1 Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No Q Q Q Q Q 180H No Q Q Q Q Q 181H You can also perform local/remote switching using the LOCAL/REMOTE Key on the Digital Operator. When the local/remote function has been set in the external terminals, the LOCAL/REMOTE Key function on the Digital Operator will be disabled. INFO 6-76 Input Terminal Functions Blocking Inverter Outputs (Baseblock Commands) Set 8 or 9 (Baseblock command NO/NC) in one of the constants H1-01 to H1-10 (multi-function contact input terminal S3 to S12 function selection) to perform baseblock commands using the terminal's ON/OFF operation, and prohibit Inverter output using the baseblock commands. At this time, the motor will be coasting and “BB” will blink on the Digital Operator. Clear the baseblock command to restart the operating using speed search from frequency references from the previous baseblock command input. Multi-function Contact Inputs (H1-01 to H1-10) Control Methods Setting Value Function V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 8 External baseblock NO (NO contact: Baseblock at ON) Yes Yes Yes Yes Yes 9 External baseblock NC (NC contact: Baseblock at OFF) Yes Yes Yes Yes Yes Time Chart The time chart when using baseblock commands is shown below. Forward operation/Stop Baseblock command Input Cleared Frequency reference Search from stored frequency reference Output frequency Hold Fig 6.50 Baseblock Commands If using baseblock commands with a variable load, do not frequently input baseblock commands during operation, as this may cause the motor to suddenly start coasting, and may result in the motor falling or slipping. IMPORTANT 6-77 Stopping Acceleration and Deceleration (Acceleration/Deceleration Ramp Hold) The acceleration/deceleration ramp hold function stops acceleration and deceleration, stores the output frequency at that point in time, and then continues operation. Set one of the constants H1-01 to H1-10 (multi-function contact input terminal S3 to S12 function selection) to A (acceleration/deceleration ramp hold) to stop acceleration and deceleration when the terminal is turned ON and to store the output frequency at that point in time. Acceleration and deceleration will restart when the terminal is turned OFF. If d4-01 is set to 1 and the Acceleration/Deceleration Ramp Hold command is input, the output frequency is still stored even after the power supply is turned OFF. Related Constants Name Constant Number Description Setting Range Factory Setting Change during Operation Sets whether or not frequencies on hold will be recorded. 0: Disabled (when operation is stopped or the power is turned on again starts at 0.) 1: Enabled (when operation is stopped or the power is turned on again starts at the previous hold frequency.) This function is available when the multi-function inputs “accel/ decel Ramp Hold” or “up/down” commands are set. 0 or 1 0 No Display Frequency reference hold function selection d4-01 MOP Ref Memory Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A Time Chart The time chart when using Acceleration/Deceleration Ramp Hold commands is given below. Power supply Forward/Stop Acceleration/Deceleration Ramp Hold Frequency reference Output frequency Hold Hold Fig 6.51 Acceleration/Deceleration Ramp Hold 6-78 MEMO BUS Register 298H Input Terminal Functions Application Precautions • When d4-01 is set to 1, the output frequency on hold is stored even after the power supply is turned OFF. If performing operations using this frequency after the Inverter has also been turned OFF, input the Run Command with the Acceleration/Deceleration Ramp Hold turned ON. • When d4-01 is set to 0 and a Run Command is input while the Acceleration/Deceleration Ramp Hold is turned ON, the output frequency will be set to zero. • If you input an Acceleration/Deceleration Ramp Hold command by error when decelerating during posi- tioning, deceleration may be canceled. Raising and Lowering Frequency References Using Contact Signals (UP/ DOWN) The UP and DOWN commands raise and lower Inverter frequency references by turning ON and OFF a multifunction contact input terminal S3 to S7. To use this function, set one of the constants H1-01 to H1-10 (multi-function contact input terminal S3 to S12 function selection) to 10 (UP command) and 11 (DOWN command). Be sure to allocate two terminals so that the UP and DOWN commands can be used as a pair. The output frequency depends on the acceleration and deceleration time. Be sure to set b1-02 (Run Command selection) to 1 (Control circuit terminal). Related Constants Name Constant Number d2-01 Display Frequency reference upper limit Ref Upper Limit d2-02 Frequency reference lower limit Ref Lower Limit d2-03 Description Setting Range Factory Setting Change during Operation Set the output frequency upper limit as a percent, taking the max. output frequency to be 100%. 0.0 to 110.0 100.0 % Sets the output frequency lower limit as a percentage of the maximum output frequency. 0.0 to 110.0 0.0 to 110.0 Master speed reference lower Set the master speed reference lower limit as a percent, taking limit the max. output frequency to be Ref1 Lower 100%. Limit Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 289H 0.0% No A A A A A 28AH 0.0% No A A A A A 293H Precautions When setting and using UP and DOWN commands, observe the following precautions. Setting Precautions If multi-function input terminals S3 to S12 are set as follows, operation error OPE03 (Invalid multi-function input selection) will occur: • Only either the UP command or DOWN command has been set. • UP/DOWN commands and Acceleration/Deceleration Ramp Hold have been allocated at the same time. 6-79 Application Precautions • Frequency outputs using UP/DOWN commands are limited by the frequency reference upper and lower limits set in constants d2-01 to d2-03. Here, frequency references from analog frequency reference terminal A1 becomes the frequency reference lower limit. If using a combination of the frequency reference from terminal A1 and the frequency reference lower limit set in either constant d2-02 or d2-03, the larger lower limit will become the frequency reference lower limit. • If inputting the Run Command when using UP/DOWN commands, the output frequency accelerates to the frequency reference lower limit. • When using UP/DOWN commands, multi-step operations are disabled. • When d4-01 (Frequency Reference Hold Function Selection) is set to 1, the frequency reference held using the UP/DOWN functions is stored even after the power supply is turned OFF. When the power supply is turned ON and the Run Command is input, the motor accelerates to the frequency reference that has been stored. To reset (i.e., to 0 Hz) the stored frequency reference, turn ON the UP or DOWN command while the Run Command is OFF. Connection Example and Time Chart The time chart and settings example when the UP command is allocated to the multi-function contact input terminal S3, and the DOWN command is allocated to terminal S4, are shown below. Constant Name Set Value H1-01 Multi-function input (terminal S3) 10 H1-02 Multi-function input (terminal S4) 11 Inverter Forward operation/Stop Reverse operation/Stop Up command Down command 0 to 10 V analog signal Sequence common Frequency reference lower limit Fig 6.52 Connection Example when UP/DOWN Commands Are Allocated 6-80 Input Terminal Functions Output frequency Upper limit Accelerates to lower limit Same frequency Lower limit Forward operation/stop UP command Reference frequency reset DOWN command Frequency matching signal* Power supply * The frequency matching signal turns ON when the motor is not accelerating/ decelerating while the Run Command is ON. Fig 6.53 UP/DOWN Commands Time Chart 6-81 Accelerating and Decelerating Constant Frequencies in the Analog References (+/- Speed) The +/- speed function increments or decrements the frequency set in analog frequency reference d4-02 (+/Speed Limit) using two contact signal inputs. To use this function, set One of the constants H1-01 to H1-10 (multi-function contact terminal inputs S3 to S12 function selection) to 1C (Trim Control Increase command) and 1D (Trim Control Decrease command). Be sure to allocate two terminals so that the Trim Control Increase command and Trim Control Decrease command can be used as a pair. Related Constants Name Constant Number d4-02 Description Display + - Speed limits Set the frequency to be add to or subtracted from the analog frequency reference as a percent, taking the maximum output frequency to be 100%. Trim Control Enabled when the increase (+) Lvl speed command or decrease (-) speed command is set for a multifunction input. Setting Range Factory Setting Change during Operation 0 to 100 10% No Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A MEMO BUS Register 299H Trim Control Increase/Decrease Command and Frequency Reference The frequency references using Trim Control Increase/Decrease command ON/OFF operations are shown below. Set Frequency Reference + d4-02 Set Frequency Reference - d4-02 Trim Control Increase Command Terminal ON OFF ON OFF Trim Control Decrease Command Terminal OFF ON ON OFF Frequency Reference Set Frequency Command Application Precautions • Trim Control Increase/Decrease command is enabled when speed reference > 0 and the speed reference is from an analog input. • When the analog frequency reference value - d4-02 < 0, the frequency reference is set to 0. • If only the Trim Control Increase command or Trim Control Decrease command has been set for a multi- function contact input terminal S3 to S12, operation error OPE03 (invalid multi-function input selected) will occur. 6-82 Input Terminal Functions Hold Analog Frequency Using User-set Timing When one of H1-01 to H1-10 (multi-function contact input terminal S3 to S12 function selection) is set to 1E (sample/hold analog frequency command), the analog frequency reference will be held from 100 ms after the terminal is turned ON, and operation will continue thereafter at that frequency. The analog value 100 ms after the command is turned ON is used as the frequency reference. Sample/hold command Analog input Frequency reference Fig 6.54 Sample/Hold Analog Frequency Precautions When setting and executing sample and hold for analog frequency references, observe the following precautions. Setting Precautions When using sample/hold of analog frequency reference, you cannot use the following commands at the same time. If these commands are used at the same time, operation error OPE03 (invalid multi-function input selection) will occur. • Acceleration/Deceleration Ramp Hold command • UP/DOWN command • Trim Control Increase/Decrease command Application Precautions • When performing sample/hold of analog frequency references, be sure to store references of 100 ms mini- mum. If the reference time is less than 100 ms, the frequency reference will not be held. • The analog frequency reference that is held will be deleted when the power supply is turned OFF. Switching Operations between a Communications Option Board and Control Circuit Terminals You can switch reference input between the Communications Option Board and the control circuit terminals. Set one of the constants H1-01 to H1-10 (multi-function contact input terminal S3 to S12 function selection) to 2 (Option/Inverter selection) to enable switching reference input using the terminal ON/OFF status when the Inverter is stopped. 6-83 Setting Precautions To switch command inputs between the Communications Option Board and the control circuit terminals, set the following constants. • Set b1-01 (Reference Selection) to 1 [Control circuit terminal (analog input)] • Set b1-02 (Operation Method Selection to 1 [Control circuit terminal (sequence inputs)] • Set one of the constants H1-01 to H1-10 (multi-function contact input terminal S3 to S12 function selec- tion) to 2 (Option/Inverter selection). Terminal Status Frequency Reference and Run Command Selection OFF Inverter (Can be operated from frequency reference or control circuit terminal from analog input terminal.) ON Communications Option Board (Frequency reference and Run Command are enabled from Communications Option Board.) Jog Frequency Operation without Forward and Reverse Commands (FJOG/RJOG) The FJOG/RJOG command functions operate the Inverter using jog frequencies by using the terminal ON/ OFF operation. When using the FJOG/RJOG commands, there is no need to input the Run Command. To use this function, set one of the constants H1-01 to H1-10 (multi-function contact input terminal S3 to S12 function selection) to 12 (FJOG command) or 13 (RJOG command). Related Constants Name Constant Number d1-17 Description Setting Range The frequency reference when the jog frequency reference selection, FJOG command, or RJOG command is ON. 0 to 400.00 * Display Jog frequency reference Jog Reference Change Factory during Setting Operation 6.00 Hz Yes Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 Q Q Q Q Q MEMO BUS Register 292H Note The unit is set in o1-03 (Frequency units of reference setting and monitor). The default for o1-03 is 0 (increments of 0.01 Hz). * The setting range for open-loop vector 2 control is 0 to 66.0 (0 to 132.0 for PRG: 103) Multi-Function Contact Inputs (H1-01 to H1-10) Control Methods Setting Value Function V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 12 FJOG command (ON: Forward run at jog frequency d1-17) Yes Yes Yes Yes Yes 13 RJOG command (ON: Reverse run at jog frequency d1-17) Yes Yes Yes Yes Yes Application Precautions • Jog frequencies using FJOG and RJOG commands are given priority over other frequency references. • When both FJOG command and RJOG commands are ON for 500 ms or longer at the same time, the Inverter stops according to the setting in b1-03 (stopping method selection). 6-84 Input Terminal Functions Stopping the Inverter by Notifying Programming Device Errors to the Inverter (External Fault Function) The external fault function performs the error contact output, and stops the Inverter operation if the Inverter peripheral devices break down or an error occurs. The digital operator will display EFx (External fault [input terminal Sx]). The x in EFx shows the terminal number of the terminal that input the external fault signal. For example, if an external fault signal is input to terminal S3, EF3 will be displayed. To use the external fault function, set one of the values 20 to 2F in one of the constants H1-01 to H1-10 (multifunction contact input terminal S3 to S12 function selection). Select the value to be set in H1-01 to H1-10 from a combination of any of the following three conditions. • Signal input level from peripheral devices • External fault detection method • Operation during external fault detection The following table shows the relationship between the combinations of conditions and the set value in H1. Set Value 20 Input Level (See Note 1.) NO Contact Yes 21 22 Yes Yes Yes Yes Yes 2D 2E 2F Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes 2B 2C Yes Yes 29 2A Yes Yes 27 28 Yes Yes 25 26 Yes Yes 23 24 NC Contact Error Detection Method Operation During Error Detection (See Note 2.) Detection DecelerCoast to EmerContinue Constant During ate to Stop Stop gency Stop Operation Detection Operation (Error) (Error) (Error) (Warning) Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Note 1. Set the input level to detect errors using either signal ON or signal OFF. (NO contact: External fault when ON; NC contact: External fault when OFF). 2. Set the detection method to detect errors using either constant detection or detection during operation. Constant detection: Detects while power is supplied to the Inverter. Detection during operation: Detects only during Inverter operation. 6-85 Output Terminal Functions The output terminal function, which sets the output methods by switching the functions of the multi-function output terminals (M1-M2, P1-PC, P2-PC, P3-C3, and P4-C4), is described here. During Run (Setting: 0) OFF The Run Command is OFF and there is not output voltage. ON The Run Command is ON or a voltage is being output. During Run 2 (Setting: 37) OFF The Inverter is not outputting a frequency. (Baseblock, DC injection braking, initial excitation, or stopped) ON The Inverter is outputting a frequency. • These outputs can be used to indicate the Inverter's operating status. Run Command Baseblock command OFF ON OFF ON Output frequency During run 1 output During run 2 output OFF ON OFF ON Fig 6.55 Timing Chart for “During RUN” Output Zero-speed (Setting: 1) OFF The output frequency is greater than the minimum output frequency (E1-09). (With flux vector control, is greater than the zero-speed level (b2-01).) ON The output frequency is less than the minimum output frequency (E1-09). (With flux vector control, is less than the zero-speed level (b2-01).) Minimum output frequency (E1-09) (Zero speed level (b2-01) when flux vector control is being used.) Output frequency Zero-speed output OFF ON Fig 6.56 Timing Chart for Zero-speed 6-86 Output Terminal Functions Motor Overload (OL1) Pre-alarm (Setting: 1F) OFF The motor protection function's electronic thermal value is less than 90% of the detection level. ON The motor protection function's electronic thermal value is greater than 90% of the detection level. • This output function is valid when the motor overload protection function is enabled (L1-01 =1). • This output can be used to warn of overheating before the protection function itself operates. Inverter Overheat (OH) Pre-alarm (Setting: 20) OFF The cooling fin temperature is less than the "OH Pre-Alarm Level" set in L8-02. ON The cooling fin temperature exceeds the "OH Pre-Alarm Level" set in L8-02. • This output function indicates that the temperature of the cooling fins reaches the temperature set in L8-02 (the Inverter overheating alarm detection level). Speed reference limit (Setting: 31) OFF Other than ON condition ON Enables the speed reference limit in the following conditions (During flux vector control method): 1. Frequency reference ≥ Frequency reference upper limit (d2-01) Frequency reference ≤ Frequency reference lower limit (d2-02) Frequency reference ≥ Output frequency lower limit of the multi-function analog input (Setting: 9) 2. The frequency reference is less than the Min. output frequency (E1-09), and b1-05 is set to 1, 2, or 3. Zero-servo End (Setting: 33) OFF The zero-servo command isn't being input or zero-servo position control hasn't been completed. ON The position has been brought within the zero-servo completion width (b9-02) after the zero-servo command was input. • This output function indicates that zero-servo position control has been completed. • The output is turned ON after the zero-servo command is input and the difference between the zero-servo operation starting position and the current position is within the zero-servo completion width (b9-02). 6-87 Monitor Constants This section explains the analog monitor and pulse monitor constants. Using the Analog Monitor Constants This section explains the analog monitor constants. Related Constants Name Constant Number H4-01 Display Monitor selection (terminal FM) Terminal FM Sel Gain (terminal FM) H4-02 Terminal FM Gain Bias (terminal FM) H4-03 H4-04 Terminal FM Bias Monitor selection (terminal AM) Terminal AM Sel Gain (terminal AM) H4-05 Terminal AM Gain Bias (terminal AM) H4-06 6-88 Terminal AM Bias Description Setting Range Sets the number of the monitor item to be output (U1-) from 1 to 45 terminal FM. 4, 10 to 14, 25, 28, 34, 39, 40 cannot be set. 29 to 31 and 41 are not 1 to 99 used. Factory Setting Change during Operation 2 Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 41DH Sets the multi-function analog output 1 voltage level gain. Sets whether the monitor item output will be output in multiples of 10 V. The maximum output from the terminal is 10 V. A meter calibration function is available. 0.00 to 2.50 1.00 Yes Q Q Q Q Q 41EH Sets the multi-function analog output 1 voltage level bias. Sets output characteristic up/ down parallel movement as a percentage of 10 V. The maximum output from the terminal is 10 V. A meter calibration function is available. -10.0 to +10.0 0.0% Yes A A A A A 41FH Sets the number of the monitor item to be output (U1-) from 1 to 45 terminal AM. 4, 10 to 14, 25, 28, 34, 39, 40 cannot be set. 29 to 31 and 41 are not 1 to 99 used. 3 No A A A A A 420H Set the voltage level gain for multi-function analog output 2. Set the number of multiples of 10 V to be output as the 100% output 0.00 to for the monitor items. The maxi2.50 mum output from the terminal is 10 V. A meter calibration function is available. 0.50 Yes Q Q Q Q Q 421H Sets the multi-function analog output 2 voltage level bias. Sets output characteristic up/ down parallel movement as a percentage of 10 V. The maximum output from the terminal is 10 V. A meter calibration function is available. 0.0% Yes A A A A A 422H -10.0 to +10.0 Monitor Constants Name Constant Number H4-07 F4-01 F4-02 F4-03 F4-04 F4-05 Display F4-06 Channel 2 output monitor bias AO Ch2 Bias F4-07 Analog output signal level for channel 1 AO Opt Level Sel F4-08 Analog output signal level for channel 2 AO Opt Level Sel Change during Operation 0 or 1 0 Control Methods MEMO BUS Register V/f Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 423H 2 No A A A A A 391H 1.00 Yes A A A A A 392H 3 No A A A A A 393H 0.00 to 2.50 0.50 Yes A A A A A 394H Sets the channel 1 item bias to 100%/10 V when the Analog Monitor Board is used. -10.0 to 10.0 0.0 Yes A A A A A 395H Sets the channel 2 item bias to 100%/10 V when the Analog Monitor Board is used. -10.0 to 10.0 0.0 Yes A A A A A 396H 0: 0 to 10 V 1: -10 to +10 V 0 or 1 0 No A A A A A 397H 0: 0 to 10 V 1: -10 to +10 V 0 or 1 0 No A A A A A 398H Channel 1 mon- Effective when the Analog Moniitor selection tor Board is used. Monitor selection: AO Ch1 Select Set the number of the monitor Channel 1 gain item to be output. (U1-) Gain: AO Ch1 Gain Set the multiple of 10 V for outputting monitor items. Channel 2 mon4, 10 to 14, 25, 28, 34, 39, 40 canitor selection not be set. 29 to 31 and 41 are not AO Ch2 Select used. When the AO-12 Analog Monitor Board is used, outputs of Channel 2 gain ± 10 V are possible. To output ± 10 V, set F4-07 or F4-08 to 1. When the AO-08 Analog Monitor Board is used, only outputs of 0 to AO Ch2 Gain +10 V are possible. A meter calibration function is available. AO Ch1 Bias Factory Setting V/f with PG Description Analog output 1 Sets the signal output level for signal level multi-function output 1 (terminal selection FM) 0: 0 to +10 V output AO Level 1: -10 to 10 V output Select1 Channel 1 output monitor bias Setting Range 1 to 45 1 to 99 0.00 to 2.50 1 to 45 1 to 99 Selecting Analog Monitor Items The digital operator monitor items (U1- [status monitor]) are output from multi-function analog output terminals FM-AC and AM-AC. Refer to Chapter 5 User Constants, and set the values for the part of U1 (status monitor). Alternatively, you can output monitor items (U1- [status monitor]) from analog output option terminal channels 1 and 2 on analog monitor boards AO-08 and AO-12. Refer to the table of constants, and set the values. 6-89 Adjusting the Analog Monitor Items Adjust the output voltage for multi-function analog output terminals FM-AC and AM-AC using the gain and bias in H4-02, H4-03, H4-05, and H4-06. Also, adjust the output voltage for output channels 1 and 2 of Analog Output option boards AO-08 and AO-12 using the gain and bias in F4-02, F4-04, F4-05, and F4-06. Adjusting the Meter The output voltage for terminals FM-AC and AM-AC and output channels 1 and 2 of the AO option board can be adjusted while the Inverter is stopped. For example, just pressing the Enter Key and displaying the data setting display for H4-02 or H4-03 will cause the following voltage to be output by the FM-AC terminals. 10 V/100% monitor output × output gain (H4-02) + output bias (H4-03) Just pressing the Enter Key and displaying the data setting display for F4-02 or F4-05 will cause the following voltage to be output to channel 1 of the AO option board. 10 V/100% monitor output × output gain (H4-02) + output bias (H4-05) Output voltage Gain x 10 V Bias x 10/100 V Monitor item Fig 6.57 Monitor Output Adjustment Switching Analog Monitor Signal Levels Monitor items corresponding to -10 to 10 V output 0 to 10 V signals when the monitor value is positive (+), and 0 to -10 V signals when the monitor value is negative (-). For monitor items corresponding to -10 to 10 V, refer to Chapter 5 User Constants. You can select the signal levels separately for multi-function analog output terminals and analog output option terminals. INFO Using Pulse Train Monitor Contents This section explains pulse monitor constants. Related Constants Name Constant Number H6-06 Display Pulse train monitor selection Pulse Output Sel 6-90 Description Setting Range Select the pulse train monitor output items (value of the part 1, 2, 5, of U1-). 20, 24, There are two types of monitor 36 items: Speed-related items and PID-related items. Factory Setting Change during Operation 2 Yes Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A MEMO BUS Register 431H Monitor Constants Name Constant Number H6-07 Description Display Pulse train Set the number of pulses output monitor scaling when speed is 100% in hertz. Set H6-06 to 2, and H6-07 to 0, to make the pulse train monitor outPO Scaling put synchronously to the output frequency. Setting Range Factory Setting Change during Operation 0 to 32000 1440 Hz Yes Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A MEMO BUS Register 432H Selecting Pulse Monitor Items Output digital operator monitor items (U1- [status monitor]) from pulse monitor terminal MP-AC. Refer to Chapter 5 User Constants, and set the part of U1- (Status monitor). The possible monitor selections are limited as follows: U1-01, 02, 05, 20, 24, 36. Adjusting the Pulse Monitor Items Adjust the pulse frequency output from pulse monitor terminal MP-AC. Set the pulse frequency output when 100% frequency is output to H6-07. Set H6-06 to 2, and H6-07 to 0, to output the frequency synchronous with the Inverter's U-phase output. Application Precautions When using a pulse monitor constant, connect a peripheral device according to the following load conditions. If the load conditions are different, there is a risk of characteristic insufficiency or damage to the machinery. Using a Sourcing Output Output Voltage (Isolated) VRL (V) Load Impedance (kΩ) +5 V min. 1.5 kΩ min. +8 V min. 3.5 kΩ min. +10 V min. 10 kΩ min. Load impedance MP VRL AC External power supply Using a Sinking Input External Power Supply (V) 12 VDC±10%, 15 VDC±10% Sink Current (mA) 16 mA Max Load impedance MP Sinking current AC 6-91 Individual Functions This section explains the individual functions used in special applications. Using MEMOBUS Communications You can perform serial communications with MEMOCON-series Programmable Controllers (PLCs) or similar devices using the MEMOBUS protocol. MEMOBUS Communications Configuration MEMOBUS communications are configured using 1 master (PLC) and a maximum of 31 slaves. Serial communications between master and slave are normally started by the master, and the slave responds. The master performs signal communications with one slave at a time. Consequently, you must set the address of each slave beforehand, so the master can perform signal communications using that address. Slaves receiving commands from the master perform the specified function, and send a response to the master. MEMOCON-series PLC Inverter Inverter Inverter RS-485 connections example Fig 6.58 Example of Connections between PLC and Inverter Communications Specifications The MEMOBUS communications specifications are shown in the following table. Item Interface RS-422, RS-485 Communications Cycle Asynchronous (Start-stop synchronization) Communications Parameters 6-92 Specifications Baud rate: Select from 1,200, 2,400, 4,800, 9,600, and 19,200 bps. Data length: 8 bits fixed Parity: Select from even, odd, or none. Stop bits: 1 bit fixed Communications Protocol MEMOBUS (RTU mode only) Number of Connectable Units 31 units max. (when using RS-485) Individual Functions Communications Connection Terminal MEMOBUS communications use the following terminals: S+, S-, R+, and R-. Set the terminating resistance by turning ON pin 1 of switch S1 for the last Inverter only, as seen from the PLC. S+ + - SRS-422A or RS-485 R+ R- S1 O F F OFF 1 2 ON Terminating resistance Switch 1 Terminating resistance (1/2 W, 110 Ohms) Fig 6.59 Communications Connection Terminal IMPORTANT 1. Separate the communication cables from the main circuit cables and other wiring and power cables. 2. Use shielded cables for the communication cables, connect the shield cover to the Inverter earth terminal, and arrange the terminals so that the other end is not connected to prevent operating errors due to noise. 3. When using RS-485 communications, connect S+ to R+, and S- to R-, on the Inverter exterior. R+ R S+ S Procedure for Communicating with the PLC Use the following procedure to perform communications with the PLC. 1. Turn OFF the power supply turned and connect the communication cable between the PLC and the Inverter. 2. Turn ON the power supply. 3. Set the required communications constants (H5-01 to H5-07) using the Digital Operator. 4. Turn OFF the power supply, and check that the Digital Operator display has completely disappeared. 5. Turn ON the power supply once again. 6. Perform communications with the PLC. Set the timer on the master to monitor response time from the slave. Set the master so that if the slave does not respond to the master within the set time, the same command message will be sent from the master again. INFO 6-93 Related Constants Name Constant Number Display Reference selection b1-01 Reference Source Operation method selection b1-02 Run Source V/f Flux Vector Open Loop Vector 2 No Q Q Q Q Q 180H 1 No Q Q Q Q Q 181H 1F No A A A A A 425H 0 to 4 3 No A A A A A 426H Set the parity for MEMOBUS communications of communications connection 0 to 2 terminals. 0 No A A A A A 427H Set the frequency reference input method. 0: Digital Operator 1: Control circuit terminal (analog input) 2: MEMOBUS communications 3: Option board 4: Pulse train input 0 to 4 1 Set the Run Command input method. 0: Digital Operator 1: Control circuit terminal (sequence input) 2: MEMOBUS communications 3: Option board 0 to 3 Set the Inverter's slave address. Communication speed selection Set the baud rate for MEMOBUS communications of communications connection terminals. Serial Baud Rate Communication parity selection H5-03 Serial Com Sel 0: 1200 bps 1: 2400 bps 2: 4800 bps 3: 9600 bps 4: 19200 bps 0 to 20 *1 0: No parity 1: Even parity 2: Odd parity H5-04 Stopping Set the stopping method for commethod after munications errors. communication 0: Deceleration to stop using error deceleration time in C1-02 1: Coast to stop 2: Emergency stop using Serial Fault Sel deceleration time in C1-09 3: Continue operation 0 to 3 3 No A A A A A 428H H5-05 CommunicaSet whether or not a communication error detec- tions timeout is to be detected as a tion selection communications error. 0: Do not detect. Serial Flt Dtct 1: Detect 0 or 1 1 No A A A A A 429H 5 to 65 5 ms No A A A A A 42AH 0 or 1 1 No A A A A A 42BH Send wait time H5-06 Transmit WaitTIM RTS control ON/OFF H5-07 6-94 MEMO BUS Register Open Loop Vector 1 Setting Range Serial Comm Adr H5-02 Control Methods V/f with PG Description Slave address H5-01 Change Factory during Setting Operation RTS Control Sel Set the time from the Inverter receiving data to when the Inverter starts to send. Select to enable or disable RTS control. 0: Disabled (RTS is always ON) 1: Enabled (RTS turns ON only when sending) Individual Functions Name Constant Number H5-10 *2 Description Display Setting Range Unit Selection Selects the units used for MEMOfor MEMOBUS BUS registry 0025H (monitors Register 0025H the output voltage reference). 0 or 1 0: 0.1 V units MEMOBUS 1: 1 V units 25H UNIT Factory Setting Change during Operation 0 No Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A MEMO BUS Register 436H * 1. Set H5-01 to 0 to disable Inverter responses to MEMOBUS communications. * 2. Applicable for G7-Series Inverters with software versions PRG: 1039 or later. MEMOBUS communications can perform the following operations regardless of the settings in b1-01 and b102. • Monitoring operation status from the PLC • Setting and reading constants • Resetting errors • Inputting multi-function commands An OR operation is performed between the multi-function commands input from the PLC and commands input from multi-function contact input terminals S3 to S12. Message Format In MEMOBUS communications, the master sends commands to the slave, and the slave responds. The message format is configured for both sending and receiving as shown below, and the length of data packets is changed by the command (function) contents. Slave address Function code Data Error check The space between messages must support the following. PLC to Inverter Command message Inverter to PLC Response message PLC to Inverter Command message Time (Seconds) 24 bits long H5-06 24 bits long setting 5 ms min. Fig 6.60 Message Spacing Slave Address Set the Inverter address from 0 to 20 Hex. If you set 0, commands from the master will be broadcast (i.e., the Inverter will not return responses). 6-95 Function Code The function code specifies commands. There are three function codes, as shown below. Function Code (Hexadecimal) Function Command Message Response Message Min. (Bytes) Max. (Bytes) Min. (Bytes) Max. (Bytes) 03H Read storage register contents 8 8 7 37 08H Loopback test 8 8 8 8 10H Write multiple storage registers 11 41 8 8 Data Configure consecutive data by combining the storage register address (test code for a loopback address) and the data the register contains. The data length changes depending on the command details. Error Check Errors are detected during communications using CRC-16. Perform calculations using the following method. 1. The factory setting for CRC-16 communications is usually 0, but when using the MEMOBUS system, set the factory setting to 1 (i.e., set all 16 bits to 1). 2. Calculate CRC-16 using MSB as slave address LSB, and LSB as the MSB of the final data. 3. Also calculate CRC-16 for response messages from the slaves, and compare them to the CRC-16 in the response messages. 6-96 Individual Functions MEMOBUS Message Example An example of MEMOBUS command/response messages is given below. Reading Storage Register Contents Read the contents of the storage register only for specified quantities whose addresses are consecutive, starting from a specified address. The contents of the storage register are separated into higher place 8 bits and lower place 8 bits, and comprise the data within response messages in address order. The following table shows message examples when reading status signals, error details, data link status, and frequency references from the slave 2 Inverter. Response Message (During Normal Operation) Command Message Response Message (During Error) Slave Address 02H Slave Address 02H Slave Address 02H Function Code 03H Function Code 03H Function Code 83H Start Address Quantity CRC-16 Higher place 00H Lower place 20H Higher place 00H Lower place 04H Higher place 45H Lower place F0H Data quantity Lead storage register Next storage register Next storage register Next storage register CRC-16 08H Higher place 00H Lower place 65H Higher place 00H Lower place 00H Higher place 00H Lower place 00H Higher place 01H Lower place F4H Higher place AFH Lower place 82H Error code CRC-16 03H Higher place F1H Lower place 31H 6-97 Loopback Test The loopback test returns command messages directly as response messages without changing the contents to check the communications between the master and slave. You can set user-defined test code and data values. The following table shows a message example when performing a loopback test with the slave 1 Inverter. Response Message (During Normal Operation) Command Message Response Message (During Error) Slave address 01H Slave address 01H Slave address 01H Function code 08H Function code 08H Function code 89H Test Code Data CRC-16 Higher place 00H Higher place 00H Lower place 00H Lower place 00H Higher place A5H Higher place A5H Lower place 37H Lower place 37H Higher place DAH Higher place DAH Lower place 8DH Lower place 8DH Test Code Data CRC-16 Error Code CRC-16 01H Higher place 86H Lower place 50H Writing to Multiple Storage Registers Write the specified data to each specified storage register from the specified addresses. The written data must be in the following order in the command message: Higher place 8 bits, then lower place 8 bits, in storage register address order. The following table shows an example of a message when forward operation has been set at a frequency reference of 60.0 Hz in the slave 1 Inverter by the PLC. Command Message Slave Address Function Code Start Address Quantity 01H 10H Higher place Lower place Higher place Lower place No. of data Lead data Next data CRC-16 6-98 Higher place Lower place Higher place Lower place Higher place Lower place 00H 01H 00H 02H 04H 00H 01H 02H 58H 63H 39H Response Message (During Normal Operation) Slave Address 01H Function Code 10H Higher 00H place Start Address Lower 01H place Higher 00H place Quantity Lower 02H place Higher 10H place CRC-16 Lower 08H place Response Message (During Error) Slave Address 01H Function Code 90H Error code CRC-16 Higher place Lower place 02H CDH C1H Individual Functions Set the number of data specified using command messages as quantity of specified messages x 2. Handle response messages in the same way. INFO Data Tables The data tables are shown below. The types of data are as follows: Reference data, monitor data, and broadcast data. Reference Data The reference data table is shown below. You can both read and write reference data. Register No. 0000H Contents Not used Frequency reference Bit 0 Forward Run/Stop Command 1: Forward run 0: Stop Bit 1 Reverse Run/Stop Command 1: Reverse run 0: Stop Bit 2 External fault 1: Error (EFO) Bit 3 Fault reset 1: Reset command Bit 4 ComNet Bit 5 ComCtrl Bit 6 Multi-function input command 3 0001H Bit 7 Multi-function input command 4 Bit 8 Multi-function input command 5 Bit 9 Multi-function input command 6 Bit A Multi-function input command 7 Bit B Multi-function input command 8 Bit C Multi-function input command 9 Bit D Multi-function input command 10 Bit E Multi-function input command 11 Bit F Multi-function input command 12 0002H Frequency reference (Set units using constant o1-03) 0003H Not used 0004H Not used 0005H Not used 0006H PID target value 0007H Analog output 1 setting (-11 V/-1540 to 11 V/1540) 0008H Analog output 2 setting (-11 V/-1540 to 11 V/1540) Multi-function contact output setting Bit 0 Contact output (Terminal M1-M2) 1: ON 0: OFF Bit 1 PHC1(Contact P1-PC) 1: ON 0: OFF Bit 2 PHC2(Contact P2-PC) 1: ON 0: OFF Bit 3 PHC3(Contact P3-C3) 1: ON 0: OFF 0009H Bit 4 PHC4(Contact P4-C4) 1: ON 0: OFF Bit 5 Not used Bit 6 Set error contact (terminal MA-MC) output using bit 7. 1: ON 0: OFF Bit 7 Error contact (terminal MA-MC) 1: ON 0: OFF Bits 8 to F Not used 000AH to 000EH Not used 6-99 Register No. 000FH Contents Reference selection settings Bit 0 Not used Bit 1 Use MEMOBUS 0006H PID target value 1: Enabled 0: Disabled Bits 2 to B Not used C Broadcast data terminal S5 input 1: Enabled 0: Disabled D Broadcast data terminal S6 input 1: Enabled 0: Disabled E Broadcast data terminal S7 input 1: Enabled 0: Disabled F Broadcast data terminal S8 input 1: Enabled 0: Disabled Note Write 0 to all unused bits. Also, do not write data to reserved registers. Monitor Data The following table shows the monitor data. Monitor data can only be read. Register No. 0020H 0021H Contents Inverter status Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Bit 8 Bit 9 Bits A and B Error details Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Bit 8 Bit 9 Bit A Bit B Bit C 0022H 0023H 0024H 0025H 0026H 0027H 6-100 Operation 1: Operating 0: Stopped Reverse operation 1: Reverse operation 0: Forward operation Inverter startup complete 1: Completed 2: Not completed Error 1: Error Data setting error 1: Error Multi-function contact output (terminal M1 - M2) 1: ON 0: OFF Multi-function PHC output 1 (terminal P1 - PC) 1: ON 0: OFF Multi-function PHC output 2 (terminal P2 - PC) 1: ON 0: OFF Multi-function PHC output 3 (terminal P3 - C3) 1: ON 0: OFF Multi-function PHC output 4 (terminal P4 - C4) 1: ON 0: OFF Not used Overcurrent (OC) Ground fault (GF) Main circuit overvoltage (OV) Inverter overload (OL2) Inverter overheat (OH1, OH2) Injection brake transistor resistance overheat (rr, rH) Fuse blown (PUF) PID feedback reference lost (FbL) External fault (EF, EFO) Hardware error (CPF) Motor overload (OL1), overtorque 1 (OL3) detected, or overtorque 2 (OL4) detected PG broken wire detected (PGO), Overspeed (OS), Speed deviation (DEV) Main circuit undervoltage (UV) detected Main circuit undervoltage (UV1), control power supply error (UV2), inrush prevention circuit error (UV3), power loss Main Circuit Voltage Fault (PF), Output Open-phase (LF) MEMOBUS communications error (CE) Operator disconnected (OPR) Bit D Bit E Bit F Data link status Bit 0 Writing data Bit 1 Not used Bit 2 Not used Bit 3 Upper and lower limit errors Bit 4 Data integrity error Bits 5 to F Not used Frequency reference (U1-01) Output frequency (U1-02) Output voltage reference (U1-06) Output current (U1-03) (Unit: 1/0.1A) Output power (U1-08) Individual Functions Register No. 0028H 0029H 002AH 002BH 002CH 002DH 002EH - 0030H 0031H 0032H 0033H 0034H - 0037H 0038H 0039H 003AH 003BH 003CH Contents Torque reference (U1-09) Not used Not used Sequence input status Bit 0 1: Control circuit terminal S1 ON Bit 1 1: Control circuit terminal S2 ON Bit 2 1: Control circuit terminal S3 ON Bit 3 1: Control circuit terminal S4 ON Bit 4 1: Control circuit terminal S5 ON Bit 5 1: Control circuit terminal S6 ON Bit 6 1: Control circuit terminal S7 ON Bit 7 1: Control circuit terminal S8 ON Bit 8 1: Control circuit terminal S9 ON Bit 9 1: Control circuit terminal S10 ON Bit A 1: Control circuit terminal S11 ON Bit B 1: Control circuit terminal S12 ON Bits C to F Not used Inverter status Bit 0 Operation 1: Operating Bit 1 Zero-speed 1: Zero-speed Bit 2 Frequency matching 1: Matched Bit 3 User-defined speed matching 1: Matched Bit 4 Frequency detection 1 1: Output frequency ≤ L4-01 Bit 5 Frequency detection 2 1: Output frequency ≥ L4-01 Bit 6 Inverter startup completed 1: Startup completed Bit 7 Low voltage detection 1: Detected Bit 8 Baseblock 1: Inverter output baseblock Bit 9 Frequency reference mode 1: Not communications 0: Communications Bit A Run Command mode 1: Not communications 0: Communications Bit B Overtorque detection 1: Detected Bit C Frequency reference lost 1: Lost Bit D Retrying error 1: Retrying Bit E Error (including MEMOBUS communications time-out) 1:Error occurred Bit F MEMOBUS communications time-out 1: Timed out Multi-function contact output status Bit 0 Multi-function contact output (terminal M1-M2) 1: ON 0: OFF Bit 1 Multi-function PHC output 1 (terminal P1 - PC) 1: ON 0: OFF Bit 2 Multi-function PHC output 2 (terminal P2 - PC) 1: ON 0: OFF Bit 3 Multi-function PHC output 3 (terminal P3 - C3) 1: ON 0: OFF Bit 4 Multi-function PHC output 4 (terminal P4 - C4) 1: ON 0: OFF Bits 5 to F Not used Not used Main circuit DC voltage Torque monitor (Unit: 1/0.1%) Output power (U1-08) Not used PID feedback quantity (Input equivalent to 100%/Max. output frequency; 10/1%; without sign) PID input quantity (±100%/±Max. output frequency; 10/1%; with sign) PID output quantity (±100%/±Max. output frequency; 10/1%; with sign) CPU software number Flash software number 6-101 Register No. Contents Communications error details Bit 0 CRC error Bit 1 Invalid data length Bit 2 Not used Bit 3 Parity error Bit 4 Overrun error Bit 5 Framing error Bit 6 Time-out Bits 7 to F Not used kVA setting Control method 003DH 003EH 003FH Note Communications error details are stored until an fault reset is input (you can also reset while the Unit is operating). Broadcast Data The following table shows the broadcast data. You can also write this data. Register Address Contents Operation signal Bit 0 Bit 1 Bits 2 and 3 Bit 4 Bit 5 Bits 6 to B Bit C Bit D Bit E Bit F Frequency reference 0001H 0002H Run Command 1: Operating 0: Stopped Reverse operation command 1: Reverse 0: Forward Not used External fault 1: Error (set using H1-01) Fault reset 1: Reset command (set using H1-02) Not used Multi-function contact input terminal S5 input Multi-function contact input terminal S6 input Multi-function contact input terminal S7 input Multi-function contact input terminal S8 input 30000/100% Note Bit signals not defined in the broadcast operation signals use local node data signals continuously. ENTER Command When writing constants to the Inverter from the PLC using MEMOBUS communications, the constants are temporarily stored in the constant data area in the Inverter. To enable these constants in the constant data area, use the ENTER command. There are two types of ENTER commands: ENTER commands that enable constant data in RAM, and ENTER commands that write data to EEPROM (non-volatile memory) in the Inverter at the same time as enabling data in RAM. The following table shows the ENTER command data. ENTER command data can only be written. The ENTER command is enabled by writing 0 to register number 0900H or 0901H. Register No. 0900H Write constant data to EEPROM 0910H Constant data is not written to EEPROM, but refreshed in RAM only. INFO 6-102 Contents The maximum number of times you can write to EEPROM using the Inverter is 100 thousand. Do not frequently execute ENTER commands (0900H) written to EEPROM. The ENTER command registers are write-only. Consequently, if reading these registers, the register address will become invalid (Error code: 02H). Individual Functions Error Codes The following table shows MEMOBUS communications error codes. Error Code Contents 01H Function code error A function code other than 03H, 08H, or 10H has been set by the PLC. 02H Invalid register number error • The register address you are attempting to access is not recorded anywhere. • With broadcast sending, a start address other than 0000H, 0001H, or 0002H has been set. 03H Invalid quantity error • The number of data packets being read or written is outside the range 1 to 16. • In write mode, the number of data packets in the message is not No. of packets x 2. 21H Data setting error • A simple upper limit or lower limit error has occurred in the control data or when writing constants. • When writing constants, the constant setting is invalid. 22H Write mode error • Attempting to write constants from the PLC during operation. • Attempting to write via ENTER commands from the PLC during operation. • Attempting to write constants other than A1-00 to A1-05, E1-03, or 02-04 when warning alarm CPF03 (defective EEPROM) has occurred. • Attempting to write read-only data. 23H Writing during main circuit undervoltage (UV) error • Writing constants from the PLC during UV (main circuit undervoltage) alarm. • Writing via ENTER commands from the PLC during UV (main circuit undervoltage) alarm. 24H Writing error during constants processing Attempting to write constants from the PLC while processing constants in the Inverter. Slave Not Responding In the following cases, the slave will ignore the write function. If the slave address specified in the command message is 0, all slaves execute the write function, but do not return response messages to the master. • When a communications error (overrun, framing, parity, or CRC-16) is detected in the command message. • When the slave address in the command message and the slave address in the Inverter do not agree. • When the data that configures the message and the data time length exceeds 24 bits. • When the command message data length is invalid. Application Precautions Set a timer in the master to monitor response time from the slaves. Make the setting so that if no response is sent to the master from the slave within the set time, the same command message is sent again from the master. 6-103 Self-Diagnosis The Inverter has a built-in function for self-diagnosing the operations of serial communications interface circuits. This function is called the self-diagnosis function. The self-diagnosis function connects the communications parts of the send and receive terminals, receives the data sent by the Inverter, and checks if communications are being performed normally. Perform the self-diagnosis function using the following procedure. 1. Turn ON the power supply to the Inverter, and set 67 (communications test mode) in constant H1-05 (Terminal S7 Function Selection). 2. Turn OFF the power supply to the Inverter. 3. Perform wiring according to the following diagram while the power supply is turned OFF. 4. Turn ON the terminating resistance. (Turn ON pin 1 on DIP switch 1.) 5. Turn ON the power supply to the Inverter again. Fig 6.61 Details of Communications Terminals “Pass” will be displayed if self-diagnosis is completed without an error occurring. If an error occurs, a CE (MEMOBUS communications error) alarm will be displayed on the Digital Operator, the error contact output will be turned ON, and the Inverter operation ready signal will be turned OFF. 6-104 Individual Functions Using the Timer Function Multi-function contact input terminals S3 to S12 can be designated as timer function input terminals, and multi-function output terminals M1-M2, P1-PC, P2-PC, P3-C3, and P4-C4 can be designated as timer function output terminals. By setting the delay time, you can erase chattering from the sensors and switches. • Set one of the constants H1-01 to H1-10 (multi-function contact input terminal S3 to S12) to 18 (timer function input). • Set H2-01 to H2-03 (multi-function output terminals M1-M2, P1-PC, P2-PC, P3-C3, and P4-C4 function selection) to 12 (timer function output). Related Constants Name Constant Number Description Setting Range Factory Setting Change during Operation Sets the timer function output ON-delay time (dead band) for the timer function input, in 1-second units. Enabled when a timer function is set in H1- or H2-. 0.0 to 300.0 0.0 s Timer function Sets the timer function output OFF-delay time OFF-delay time (dead band) for the timer function input, in 1-second units. Delay-OFF Enabled when a timer function is Timer set in H1- or H2-. 0.0 to 300.0 0.0 s Display Timer function ON-delay time b4-01 b4-02 Delay-ON Timer Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 1A3H No A A A A A 1A4H Setting Example When the timer function input ON time is longer than the value set in b4-01, the timer output function is turned ON. When the timer function input OFF time is longer than the value set in b4-02, the timer output function is turned OFF. An example of timer function operation is given in the following diagram. Timer function input Timer function output Fig 6.62 Timer Function Operation Example 6-105 Using PID Control PID control is a method of making the feedback value (detection value) match the set target value. By combining proportional control (P), integral control (I), and derivative control (D), you can even control targets (machinery) with play time. The characteristics of the PID control operations are given below. P control Outputs the amount of operation proportional to the deviation. You cannot, however, set the deviation to zero using P control alone. I control Outputs the amount of operation that integrates the deviation. Used for matching feedback value to the target value. I control is not suited, however, to rapid variations. D control Outputs the amount of operation derived from the deviation. Can respond promptly to rapid variations. PID Control Operation To understand the differences between each PID control operation (P, I, and D, the variation in the amount of operation (output frequency) is as shown in the following diagram when the deviation (i.e., the difference between the target value and feedback value) is fixed. Deviation Time PID control Amount of operation I control D control P control Time Fig 6.63 PID Control Operation PID Control Applications The following table shows examples of PID control applications using the Inverter. Application 6-106 Control Details Example of Sensor Used • Feeds back machinery speed information, and matches speed to the target value. Speed Con• Inputs speed information from other machinery as the target value, and performs trol synchronous control using the actual speed feedback. Tachometer generator Pressure Control Feeds back pressure information, and performs constant pressure control. Pressure sensor Flow Rate Control Feeds back flow rate information, and controls the flow rate highly accurately. Flow rate sensor Temperature Control Feeds back temperature information, and performs temperature adjustment control by rotating the fan. • Thermocouple • Thermistor Individual Functions Related Constants Name Constant Number Change Factory during Setting Operation V/f Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 1A5H 1.00 Yes A A A A A 1A6H 0.0 to 360.0 1.0 s Yes A A A A A 1A7H 0.0 to 100.0 100.0 % Yes A A A A A 1A8H 0.00 to 10.00 0.00 s Yes A A A A A 1A9H 0.0 to 100.0 100.0 % Yes A A A A A 1AAH -100.0 to +100.0 0.0% Yes A A A A A 1ABH Sets the time constant for low pass filter for PID-control outputs 0.00 to in 1-second units. 10.00 Not usually necessary to set. 0.00 s Yes A A A A A 1ACH Setting Range 0: Disabled 1: Enabled (Deviation is Dcontrolled.) 2: Enabled (Feedback value is Dcontrolled.) 3: PID control enabled (frequency reference + PID output, D control of deviation) 4: PID control enabled (frequency reference + PID output, D control of feedback value). 0 to 4 0 Sets P-control proportional gain as a percentage. P-control is not performed when the setting is 0.00. 0.00 to 25.00 b5-03 Integral (I) time Sets I-control integral time in 1second units. I-control is not performed when PID I Time the setting is 0.0. b5-04 Integral (I) limit Sets the I-control limit as a percentage of the maximum output PID I Limit frequency. PID control method selection b5-01 PID Mode b5-02 Proportional gain (P) PID Gain b5-05 Derivative (D) time PID D Time b5-06 b5-07 PID Offset b5-08 PID first order lag time constant PID Delay Time b5-09 PID output characteristics selection Output Level Sel b5-10 Sets D-control derivative time in 1-second units. D-control is not performed when the setting is 0.00. PID upper limit Sets the upper limit after PIDcontrol as a percentage of the PID Limit maximum output frequency. PID offset adjustment PID output gain Output Gain PID reverse output selection b5-11 Output Rev Sel MEMO BUS Register V/f with PG Description Display Control Methods Sets the offset after PID-control as a percentage of the maximum output frequency. Select forward/reverse for PID output. 0: PID output is forward. 1: PID output is reverse (highlights the output code) 0 or 1 0 No A A A A A 1ADH Sets output gain. 0.0 to 25.0 1.0 No A A A A A 1AEH 0: 0 limit when PID output is negative. 1: Reverses when PID output is negative. 0 limit when reverse prohibit is selected using b1-04. 0 or 1 0 No A A A A A 1AFH 6-107 Name Constant Number Setting Range Factory Setting Change during Operation 0 to 2 0 0 to 100 Fb los Det Lvl Sets the PID feedback loss detection level as a percent units, with the maximum output frequency at 100%. PID feedback command loss detection time Sets the PID feedback loss detection level in s units. Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 1B0H 0% No A A A A A 1B1H 0.0 to 25.5 1.0 s No A A A A A 1B2H b5-15 PID sleep function operation Set the PID sleep function start level level as a frequency. PID Sleep Level 0.0 to 400.0 0.0 Hz No A A A A A 1B3H b5-16 PID sleep operation delay time Set the delay time until the PID sleep function starts in seconds. PID Sleep Time 0.0 to 25.5 0.0 s No A A A A A 1B4H 0.0 to 25.5 0.0 s No A A A A A 1B5H 0 to 2 0 No A A A A A 42CH Description Display Selection of PID feedback command loss detection 0: No detection of loss of PID feedback. 1: Detection of loss of PID feedback. Operation continues during detection, with the malfunctioning contact not operating. 2: Detection of loss of PID feedback. Coasts to stop during detection, and fault contact operates. b5-12 Fb los Det Sel b5-13 b5-14 PID feedback command loss detection level Fb los Det Time b5-17 Accel/decel time for PID reference Set the accel/decel time for PID reference in seconds. PID SFS Time H6-01 Pulse train input function selection Pulse Input Sel 0: Frequency reference 1: PID feedback value 2: PID target value Monitor Functions Name Constant Number Display PID feedback value U1-24 U1-36 PID Feedback PID input volume PID Input 6-108 Control Methods Description Output Signal Level During Multi-Function Analog Output Min. Unit V/f V/f with PG Open Loop Vector 1 Flux Vector Open MEMO BUS Loop RegVecister tor 2 Monitors the feedback value when PID control is used. The input for the max. frequency corresponds to 100%. 10 V: Max. frequency (-10 to 10 V possible) 0.01 % A A A A A 57H PID feedback volume Given as maximum frequency/100% 10 V: Max. frequency (-10 to 10 V possible) 0.01 % A A A A A 58H Individual Functions Name Constant Number U1-37 Control Methods Description Display PID output volume PID control output Given as maximum frequency/100% PID Output U1-38 Output Signal Level During Multi-Function Analog Output 10 V: Max. frequency (-10 to 10 V possible) PID command PID command + PID command bias Given as maximum frePID Setpoint quency/100% 10 V: Max. frequency Open MEMO BUS Loop RegVecister tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector 0.01 % A A A A A 59H 0.01 % A A A A A 5AH Min. Unit Multi-Function Contact Inputs (H1-01 to H1-10) Control Methods Setting Value Function V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 19 PID control disable (ON: PID control disabled) Yes Yes Yes Yes Yes 30 PID control integral reset (reset when reset command is input or when stopped during PID control) Yes Yes Yes Yes Yes 31 PID control integral hold (ON: Hold) Yes Yes Yes Yes Yes 34 PID soft starter Yes Yes Yes Yes Yes 35 PID input characteristics switch Yes Yes Yes Yes Yes Multi-Function Analog Input (H3-05, H3-09) Control Methods Setting Value Function Contents (100%) V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 B PID feedback Maximum output frequency Yes Yes Yes Yes Yes C PID target value Maximum output frequency Yes Yes Yes Yes Yes PID Control Methods There are four PID control methods. Select the method by setting constant b5-01. Set Value Control Method 1 PID output becomes the Inverter output frequency, and D control is used in the difference between PID target value and feedback value. 2 PID output becomes the Inverter output frequency, and D control is used in the PID feedback value. 3 PID output is added as compensation value of the Inverter output frequency, and D control is used in the difference between PID target value and feedback value. 4 PID output is added as compensation value of the Inverter output frequency, and D control is used in the PID feedback value. 6-109 PID Input Methods Enable PID control using constant b5-01, and set the PID target value and PID feedback value. PID Target Value Input Methods Select the PID control target value input method according to the setting in b1-01 (Reference Selection). Normally, the frequency reference selected in b1-01 is the PID target value, but you can also set the PID target value as shown in the following table. PID Target Input Method Setting Conditions Multi-Function Analog Terminal A2, or A3 Input Set H3-05 or H3-09 to C (PID target value). Also, be sure to set H6-01 (pulse train input function selection) to 1 (PID feedback value). The negative inputs cannot be used for target values. MEMOBUS register 0006H Set MEMOBUS bit 1 in register address 000FH to 1 (enable/disable PID target value from communications) to be able to use register number 0006H as the PID target value. Pulse train input Set H6-01 to 2 (PID target value). PID Feedback Input Methods Select one of the following PID control feedback input methods. Input Method Setting Conditions Multi-function analog input Set H3-09 (Multi-function Analog Input Terminal A2 Selection) or H3-05 (Multi-function Analog Input Terminal A3 Function Selection) to B (PID feedback). Pulse train input Set H6-01 to 1 (PID feedback). Adjust PID target value and PID feedback value using the following items. • Analog input: Adjust using the analog input terminal gain and bias. • Pulse train input: Adjust using pulse train scaling, pulse train input gain, and pulse train input bias. INFO PID Adjustment Methods Use the following procedure to adjust PID while performing PID control and measuring the response waveform. 1. Set b5-01 (PID Control Method Selection) to 1 or 2 (PID control enabled). 2. Increase b5-02 (Proportional Gain (P)) to within a range that does not vibrate. 3. Reduce b5-03 (Integral (I) time) to within a range that does not vibrate. 4. Increase b5-05 (Derivative (D) time) to within a range that does not vibrate. 6-110 Individual Functions PID Fine Adjustment Methods This section explains the fine adjustment of PID after setting the PID control constants. Suppressing Overshoot If overshoot occurs, reduce derivative time (D), and increase integral time (I). Response Before adjustment After adjustment Time Set a Rapidly Stabilizing Control Condition To rapidly stabilize the control even if overshoot occurs, reduce integral time (I), and lengthen derivative time (D). Response Before adjustment After adjustment Time Suppressing Long-cycle Vibration If vibration occurs with a longer cycle than the integral time (I) set value, the integral operation is too strong. Lengthen the integral time (I) to suppress the vibration. Response Before adjustment After adjustment Time 6-111 Suppressing Short Cycle Vibration If vibration occurs when the vibration cycle is short, and the cycle is almost identical to the derivative time (D) set value, the differential operation is too strong. Shorten the derivative time (D) to suppress the vibration. If vibration continues even when the derivative time (D) is set to 0.00 (D control disabled), reduce the proportional gain (P), or increase the PID primary delay time constant. Response Before adjustment After adjustment Time Setting Precautions • In PID control, the b5-04 constant is used to prevent the calculated integral control value from exceeding a specified amount. If the load changes rapidly, the machine may be damaged or the motor may stall because of unpredictable response from the Inverter. In this case, reduce the set value. • The b5-06 constant is used to prevent the arithmetic operation following the PID control calculation from exceeding a specified amount. Set taking the maximum output frequency to be 100%. • The b5-07 constant is used to adjust PID control offset. Set in increments of 0.1%, taking the maximum output frequency to be 100%. • Set the low pass filter time constant for the PID control output in b5-08. Enable this constant to prevent machinery resonance from occurring when machinery adhesive abrasion is great, or rigidity is poor. In this case, set the constant to be greater than the resonance frequency cycle. Increase this time constant to reduce Inverter responsiveness. • Using b5-09, you can invert the PID output polarity. Consequently, if you increase the PID target value, you can apply this constant to applications to lower the Inverter output frequency. • Using b5-10, you can apply gain to the PID control output. Enable this constant to adjust the amount of compensation if adding PID control output to the frequency reference as compensation. • When PID control output is negative, you can use constant b5-11 to invert the Inverter. When b1-04 (Pro- hibition of Reverse Operation) is set to 1 (enabled), however, PID output limit is 0. • With the Inverter, by setting an independent acceleration/deceleration time in constant b5-17, you can increase or decrease the PID target value using the acceleration/deceleration time. The acceleration/ deceleration function (constant C1) used normally, however, is allocated after PID control, so depending on the settings, resonance with PID control and hunting in the machinery may occur. If this happens, reduce constant C1 until hunting does not occur, and maintain the acceleration/deceleration time using b517. Also, you can disable the set value in b5-17 from the external terminals during operation using multifunction input set value 34 (PID soft starter ON/OFF). 6-112 PID feed-back value (U1-24) Z -1 + H6-01=2 + b5-01=2,4 + H6-01=1 b5-01=1,3 P -1 Select multi-function inputs PID input characteristics Proportional gain (P) b5-02 + PID OFF b5-01=3,4 b5-01=1,2 b5-01=0 Z-1 + 1 T Z -1 Derivative time + PID ON b5-01=2,4 + + + Integral rset using multi-function inputs Integral (I) time b5-04 b5-01=1,3 + + b5-05 Integral (I) time b5-03 Store integral using multi-function inputs PID target value (U1-38) Multi-function input PID control cancel signal is ON. PID is OFF under the following conditions: b5-01 = 0 During JOG command input Frequency reference (U1-01) PID input volume (U1-36) Set PID target value in multi-function analog input H3-05 or H3-09=B 0 PID SFS Cancel b5-17 1 Frequency reference using multi-step command Set bit 1 of MEMOBUS register 0FH to 1 0 1 2 3 4 b5-05 Derivative (D) time Pulse input terminal RP Terminal A2 or A3 PID feedback Terminal A2 or A3 PID target value MEMOBUS communications register 06 H PID target value Pulse input terminal RP d1-16 d1-02 d1-01 Terminal A1 Serial Com Option Card Pulse train input b1-01 + Lower limit -(Fmaxx109%) 1 T + + 1 Output frequency (U1-02) + PID offset adjustment (b5-07) -1 + PID output gain (b5-10) PID output monitor (U1-37) 1 Select PID output characteristics selection (b5-09) Z -1 0 Lower limit 0 Upper limit Fmax x109% Upper limit Fmax x109% b5-11=0 PID first order lag time constant b5-08 b5-11=1 PID upper limit b5-06 PID Limit + Enable/disable reverse operation when PI output is negative Individual Functions PID Control Block The following diagram shows the PID control block in the Inverter. Fig 6.64 PID Control Block 6-113 PID Feedback Loss Detection When performing PID control, be sure to use the PID feedback loss detection function. If PID feedback is lost, the Inverter output frequency may accelerate to the maximum output frequency. When setting b5-12 to 1 and the status of the PID feedback value detection level in b5-13 is insufficient and continues for the time set in b5-14, an FbL (PID feedback reference lost) alarm will be displayed on the Digital Operator and Inverter operation will continue. When b5-12 is set to 2, an FbL (PID feedback reference lost) error alarm will be displayed on the Digital Operator, the error contact will operate, and Inverter operation will be stopped. The time chart for PID feedback loss detection (set b5-12 to 2) is shown below. PID feedback value Loss detection level (b5-13) Time No FbL detection Loss detection time (b5-14) FbL detection Loss detection time (b5-14) Fig 6.65 PID Feedback Loss Detection Time Chart PID Sleep The PID sleep function stops the Inverter when the PID sleep function delay time continues while the PID control target value is at an insufficient level to operate the PID sleep function. When the PID sleep delay time continues and the PID control target value is above the PID sleep function operation level, Inverter operation will automatically resume. When PID control is disabled, the PID sleep function is also disabled. When using the PID sleep function, select decelerate to stop or coast to stop as the stopping method. The PID sleep time chart is shown below. PID target value Sleep operation level b5-15 Sleep operation delay time Internal Run Command External Run Command Operating Sleep operation delay time b5-16 Operation b5-16 Stopped Run Command has been input Operation status output Fig 6.66 PID Sleep Time Chart 6-114 Individual Functions Energy-saving To perform energy saving, set b8-01 (Energy Saving Mode Selection) to 1. Energy-saving control can be performed using both V/f control and vector control. The constants to be adjusted are different for each. In V/f control, adjust b8-04 to b8-06, and in vector control, adjust b8-02 and b8-03. Related Constants Name Constant Number b8-01 b8-02 b8-03 Display Energy-saving mode selection Energy Save Sel Energy-saving gain Energy Save Gain Energy-saving filter time constant Energy Save F.T Energy-saving coefficient b8-04 b8-05 Energy Save COEF Setting Range Factory Setting Change during Operation Select whether to enable or disable energy-saving control. 0: Disable 1: Enable 0 or 1 0 Set the energy-saving gain with the open-loop vector control method. 0.0 to 10.0 0.7 Set the energy-saving filter time constant with the open-loop vector control method. 0.00 to 10.0 0.50 s Set the maximum motor efficiency value. Set the motor rated capacity in E2-11, and adjust the value by 5% at a time until output power reaches a minimum value. 0.0 to 288.20 655.00 *3 *4 Description Power detection filter time con- Set the time constant for output stant power detection. *1 *2 Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 1CCH Yes No No A A A 1CDH Yes No No A A A 1CEH No A A No No No 1CFH 0 to 2000 20 ms No A A No No No 1D0H 0 to 100 0% No A A No No No 1D1H 2.90 Hz No A A A A A 30FH No Q Q Q Q Q 318H kW Filter Time Search operation voltage limiter b8-06 Search V Limit E2-02 E2-11 Set the limit value of the voltage control range during search operation. Perform search operation to optimize operations using minute variations in voltage using energy-saving control. Set to 0 to disable the search operation. 100% is the motor base voltage. Motor rated slip Sets the motor rated slip in Hz units. These set values will become the reference values for slip compenMotor Rated sation. Slip This constant is automatically set during autotuning. Motor rated output Mtr Rated Power Set the rated output of the motor in units of 0.01 kW. This constant is automatically set during autotuning. 0.00 to 20.00 0.00 to 650.00 *4 0.40 *4 * 1. The factory setting is 1.0 when using flux vector control. * 2. The factory setting is 2.00 s when Inverter capacity is 55 kW min. The factory setting will change when the control method is changed. The open-loop vector 1 factory setting is given. * 3. By setting E2-11 (Motor rated output) the appropriate value will be set. * 4. The factory settings depend on the Inverter capacity. The values for a 200 V Class Inverter of 0.4 kW are given. 6-115 Adjusting Energy-saving Control The method of adjustment during energy-saving control operations differs depending on the control method. Refer to the following when making adjustments. V/f Control In V/f control method, the voltage for optimum motor efficiency is calculated and becomes the output voltage reference. • b8-04 (Energy-saving Coefficient) is set at the factory for motor use applied to the Inverter. If the motor capacity differs from the motor applied to the Inverter, set the motor capacity in E2-11 (Motor Rated Output). Also, adjust the output voltage in steps of 5 until it reaches minimum. The larger the energy-saving coefficient, the greater the output voltage. • To improve response when the load fluctuates, reduce the power detection filter time constant b8-05. If b8- 05 is set too small, however, motor rotations when the load is light may become unstable. • Motor efficiency varies due to temperature fluctuations and differences in motor characteristics. Conse- quently, control motor efficiency online to optimize efficiency by causing minute variations in voltage using the search operation. Constant b8-06 (Search Operation Voltage Limiter) controls the range that control the voltage using the search operation. For 200 V Class Inverters, set the range to 100%/200 V, and for 400 V Class Inverters, set the range to 100%/400 V. Set to 0 to disable the search operation. Vector Control In vector control method, control the slip frequency so that motor efficiency is maximized. • Taking the motor rated slip for the base frequency as optimum slip, calculate the optimum slip for motor efficiency for each frequency. In vector control, be sure to perform autotuning, and set the motor rated slip. • If the motor performs hunting when using energy-saving control in vector control, reduce the set value in b8-02 (Energy-saving Gain), or increase the set value in b8-03 (Energy-saving Filter Time Constant). 6-116 Individual Functions Setting Motor Constants In vector control method, the motor constants are set automatically using autotuning. If autotuning does not complete normally, set them manually. Related Constants Name Constant Number Display Motor rated current E2-01 E2-02 E2-03 E2-04 E2-05 Motor Rated FLA Motor no-load current No-Load Current Number of motor poles Number of Poles Motor line-toline resistance Term Resistance E2-07 Leak Inductance Motor iron saturation coefficient 1 Saturation Comp1 E2-08 Motor iron saturation coefficient 2 Saturation Comp2 Factory Setting Sets the motor rated current in 1 A units. These set values will become the 0.32 to reference values for motor protec1.90 A 6.40 *1 tion, torque limits and torque con*2 trol. This constant is automatically set during autotuning. Motor rated slip Sets the motor rated slip in Hz units. These set values will become the reference values for slip compenMotor Rated sation. Slip This constant is automatically set during autotuning. Motor leak inductance E2-06 Description Setting Range 0.00 to 20.00 2.90 Hz Change during Operation Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No Q Q Q Q Q 30EH No A A A A A 30FH No A A A A A 310H *1 Sets the motor no-load current in 1 A units. This constant is automatically set during autotuning. 0.00 to 1.20 A 1.89 *1 Sets the number of motor poles. This constant is automatically set during autotuning. 2 to 48 4 poles No No Q No Q Q 311H Sets the motor phase-to-phase resistance in Ω units. This constant is automatically set during autotuning. 0.000 to 65.000 9.842 Ω No A A A A A 312H Sets the voltage drop due to motor leakage inductance as a percentage of the motor rated voltage. This constant is automatically set during autotuning. 0.0 to 40.0 18.2% No No No A A A 313H Sets the motor iron saturation coefficient at 50% of magnetic flux. This constant is automatically set during rotational autotuning. 0.00 to 0.50 0.50 No No No A A A 314H Sets the motor iron saturation coefficient at 75% of magnetic flux. This constant is automatically set during rotational autotuning. 0.00 to 0.75 0.75 No No No A A A 315H *3 *1 *1 6-117 Name Constant Number E2-10 Description Display Motor iron loss for torque compensation Sets motor iron loss in W units. Tcomp Iron Loss E2-12 Motor iron saturation coefficient 3 Saturation Comp3 Sets the motor iron saturation coefficient at 130% of magnetic flux. This constant is automatically set during rotational autotuning. Setting Range Factory Setting 0 to 65535 14 W 1.30 to 1.60 *1 1.30 Change during Operation Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A No No No 317H No No No A A A 328H * 1. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. * 2. The setting range is from 10% to 200% of the Inverter rated output current. The value for a 200 V Class Inverter for 0.4 kW is given. For the motor no-load current, set E2-03 to a value less than that of E2-01. * 3. The setting range depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. The upper limit depends on the setting of E2-01. Manual Motor Constant Setting Methods The motor constants settings methods are given below. Make (enter) settings referring to the motor test report. Motor Rated Voltage Setting Set E2-01 to the rated current on the motor nameplate. Motor Rated Slip Setting Set E2-02 to the motor rated slip calculated from the number of rated rotations on the motor nameplate. Amount of motor rated slip = Motor rated frequency (Hz) - No. of rated rotations (min−1) x No. of motor poles/120. Motor No-Load Current Setting Set E2-03 to the motor no-load current using the rated voltage and rated frequency. The motor no-load current is not normally written on the motor nameplate. Consult the motor manufacturer. Factory setting is the no-load current value for a standard Yaskawa 4-pole motor. Number of Motor Poles Setting Set the number of motor poles (number of poles) as written on the motor nameplate. E2-04 is not displayed when V/f control or open-loop vector control is selected. Motor Line-to-Line Resistance Setting E2-05 is set automatically when performing motor line-to-line resistance autotuning. When you cannot perform tuning, consult the motor manufacturer for the line-to-line resistance value. Calculate the resistance from the line-to-line resistance value in the motor test report using the following formula, and then make the setting accordingly. • E-type isolation: [Line-to-line resistance (Ω) at 75°C of test report] × 0.92 (Ω) • B-type isolation: [Line-to-line resistance (Ω) at 75°C of test report] × 0.92 (Ω) • F-type isolation: [Line-to-line resistance (Ω) at 115°C of test report] × 0.87 (Ω) 6-118 Individual Functions Motor Leak Inductance Setting Set the amount of voltage drop due to motor leak inductance in E2-06 using the percentage over the motor rated voltage. Make this setting when the high-speed motor inductance is small. If the inductance is not written on the motor nameplate, consult the motor manufacturer. Motor Iron Saturation Coefficients 1, 2 and 3 Settings E2-07, E2-08 and E2-12 are set automatically using rotational autotuning. Motor Iron Loss for Torque Compensation Setting E2-10 is displayed only when in V/f control method. To increase the torque compensation accuracy when in V/f control method, set the motor iron loss in Watts. Motor Mechanical Loss When using flux vector control, adjust mechanical loss in the following cases. (There is normally no reason to make this adjustment.) The mechanical loss setting is used to compensate the torque. • There is excessive torque loss from the motor bearings. • There is excessive torque loss from a fan, pump, etc. 6-119 Setting the V/f Pattern In V/f control method, you can set the Inverter input voltage and the V/f pattern as the need arises. Related Constants Name Constant Number E1-01 Display Input voltage setting Input Voltage V/f pattern selection E1-03 V/F Selection E1-04 Description Set the Inverter input voltage in 1 volt. This setting is used as a reference value in protection functions. 0 to E: Select from the 15 preset patterns. F: Custom user-set patterns (Applicable for settings E1-04 to E1-10.) Max. output frequency Max Frequency Max. voltage E1-05 E1-06 E1-07 E1-08 Max Voltage Base frequency Mid Frequency A Mid. output frequency voltage Mid Voltage A E1-09 E1-10 Min. output frequency Min Frequency Min. output frequency voltage Min Voltage 6-120 Factory Setting 155 to 255 200 V *1 *1 Change during Operation Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No Q Q Q Q Q 300H 0 to F F No Q Q No No No 302H 40.0 to 400.0 60.0 Hz No Q Q Q Q Q 303H *5 *2 0.0 to 255.0 200.0 V No Q Q Q Q Q 304H *1 *1*2 0.0 to 400.0 60.0 Hz No Q Q Q Q Q 305H *5 *2 0.0 to 400.0 3.0 Hz No A A A No No 306H No A A A No No 307H No Q Q Q A Q 308H No A A A No No 309H Output voltage (V) Base Frequency Mid. output frequency Setting Range Frequency (Hz) To set V/f characteristics in a straight line, set the same values for E1-07 and E1-09. In this case, the setting for E1-08 will be disregarded. Always ensure that the four frequencies are set in the following manner: E1-04 (FMAX) ≥ E1-06 (FA) > E107 (FB) ≥ E1-09 (FMIN) 0.0 to 255.0 *1 0.0 to 400.0 *5 0.0 to 255.0 *1 *2 11.0 V *1 *2 0.5 Hz *2 2.0 V *1 *2 Individual Functions Name Constant Number E1-11 E1-12 E1-13 * * * * * 1. 2. 3. 4. 5. Display Description Mid. output frequency 2 Mid Frequency B Mid. output frequency voltage 2 Setting Range Factory Setting 0.0 to 400.0 0.0 Hz *5 Set only to fine-adjust V/f for the output range. Normally, this setting is not required. 0.0 to 255.0 Mid Voltage B *1 Base voltage 0.0 to 255.0 Base Voltage *1 Change during Operation *3 0.0 V *3 0.0 V *4 Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 30AH No A A A A A 30BH No A A Q Q Q 30CH These are values for a 200 V Class Inverter. Values for a 400 V Class Inverter are double. The factory setting will change when the control method is changed. The open-loop vector 1 factory settings are given. E1-11 and E1-12 are disregarded when set to 0.0. E1-13 is set to the same value as E1-05 by autotuning. The setting range for open-loop vector 2 control is 0 to 66.0 (0 to 132.0 for PRG: 103). Setting Inverter Input Voltage Set the Inverter input voltage correctly in E1-01 to match the power supply voltage. This set value will be the standard value for the protection function and similar functions. The overvoltage detection level (OV) and the braking transistor operation level (BTR) vary depending on the input voltage as shown in the following table. Inverter Class 200 V Class 400 V Class All values 400 V or more Approx. 410 V Approx. 820 V BTR Operation Level∗ Approx. 394 V Approx. 788 V Less than 400 V Approx. 720 V Approx. 682 V E1-01 Setting OV Detection Level * These are values of operation levels for braking transistors built in Inverters of 0.4 to 15 kW. Refer to FOR VARISPEED-600 SERIES INVERTER BRAKING UNIT BRAKING RESISTOR UNIT INSTRUCTIONS (TOBPC720600000) for operation levels for separately-installed type Braking Resistor Units. If selecting a fixed V/f pattern (E1-03 = 0 to E) in V/f control the values of the max. voltage (E1-05), the mid. Output frequency voltage (E1-08), and the min. output frequency voltage (E1-10) will change if the value for the input voltage setting (E1-01) is changed. 6-121 Setting V/f Pattern Set the V/f pattern in E1-03 when using V/f control (with or without a PG). There are two methods of setting the V/f pattern: Select one of the 15 pattern types (set value: 0 to E) that have been set beforehand, or set a user-defined V/f pattern (set value: F). The factory setting for E1-03 is F. The contents of E1-03 when factory-set to F are the same as when E1-03 is set to 1. To select one of the existing patterns, refer to the following table. Characteristic Constant Torque Characteristic Variable torque characteristic High Startup Torque (See Note)* Fixed Output Operation Application This pattern is used in general applications. Used when the load torque is fixed, regardless of rotation speed, for linear transport systems. This pattern is used for loads with torque proportional to two or three times the rotation speed, such as fans and pumps. Select the high startup torque V/f pattern only in the following cases. • The wiring distance between Inverter and motor is large (approx. 150 m min.) • A large torque is required at startup (elevator loads, etc.) • An AC reactor is inserted in the Inverter input or output. • You are operating a motor that is less than optimum. This pattern is used for frequencies of 60 Hz or higher. A fixed voltage is applied. Set Value Specifications 0 50 Hz specifications 1 (F) 60 Hz specifications 2 60 Hz specifications, voltage saturation at 50 Hz 3 72 Hz specifications, voltage saturation at 60 Hz 4 50 Hz specifications,× 3 decrement 5 50 Hz specifications, × 2 decrement 6 60 Hz specifications, × 3 decrement 7 60 Hz specifications, × 2 decrement 8 50 Hz specifications, medium startup torque 9 50 Hz specifications, large startup torque A 60 Hz specifications, medium startup torque B 60 Hz specifications, large startup torque C 90 Hz specifications, voltage saturation at 60 Hz D 120 Hz specifications, voltage saturation at 60 Hz E 180 Hz specifications, voltage saturation at 60 Hz * The torque is protected by the fully automatic torque boost function, so normally there is no need to use this pattern. When you select these patterns, the values of constants E1-04 to E1-10 are changed automatically. There are three types of values for E1-04 to E1-10, depending on the Inverter capacity. • 0.4 to 1.5 kW V/f pattern • 2.2 to 45 kW V/f pattern • 55 to 300 kW V/f pattern The characteristics diagrams for each are shown in the following pages. 6-122 Individual Functions 0.4 to 1.5 kW V/f Pattern The diagrams show characteristics for a 200-V class motor. For a 400-V class motor, multiply all voltages by 2. • Constant Torque Characteristics (Set Value: 0 to 3) Set Value 0 50 Hz Set Value 1 60 Hz (Initial value of set value F) Set Value 2 60 Hz Set Value 3 72 Hz 50 Hz Set Value 6 60 Hz Set Value 7 60 Hz 50 Hz Set Value A 60 Hz Set Value B 60 Hz Set Value E 180 Hz • Decrement Torque Characteristics (Set Value: 4 to 7) Set Value 4 50 Hz Set Value 5 • High startup torque (Set value 8: to B) Set Value 8 50 Hz Set Value 9 • Fixed Output Operation (Set Value: C to E) Set Value C 90 Hz Set Value D 120 Hz 6-123 2.2 to 45 kW V/f Pattern The diagrams show characteristics for a 200-V class motor. For a 400-V class motor, multiply all voltages by 2. • Constant Torque Characteristics (Set Value: 0 to 3) Set Value 0 50 Hz Set Value 1 60 Hz Set Value 2 60 Hz Set Value 3 72 Hz 50 Hz Set Value 6 60 Hz Set Value 7 60 Hz 50 Hz Set Value A 60 Hz Set Value B 60 Hz Set Value E 180 Hz (Initial value of set value F) • Decrement Torque Characteristics (Set Value: 4 to 7) Set Value 4 50 Hz Set Value 5 • High Startup Torque (Set Value: 8 to B) Set Value 8 50 Hz Set Value 9 • Fixed Output Operation (Set Value: C to E) Set Value C 6-124 90 Hz Set Value D 120 Hz Individual Functions 55 to 300 kW V/f Pattern The diagrams show characteristics for a 200-V class motor. For a 400-V class motor, multiply all voltages by 2. • Constant Torque Characteristics (Set Value: 0 to 3) Set Value 0 50 Hz Set Value 1 60 Hz Set Value 2 60 Hz Set Value 3 72 Hz 50 Hz Set Value 6 60 Hz Set Value 7 60 Hz 50 Hz Set Value A 60 Hz Set Value B 60 Hz Set Value E 180 Hz (Initial value of set value F) • Decrement Torque Characteristics (Set Value: 4 to 7) Set Value 4 50 Hz Set Value 5 • High Startup Torque (Set Value: 8 to B) Set Value 8 50 Hz Set Value 9 • Fixed Output Operation (Set Value: C to E) Set Value C 90 Hz Set Value D 120 Hz 6-125 When E1-03 is set to F (User-defined V/f pattern), you can set constants E1-04 to E1-10. If E1-03 is set to anything other than F, you can only refer to constants E1-04 to E1-10. If the V/f characteristics are linear, set E1-07 and E1-09 to the same value. In this case, E1-08 will be ignored. Output voltage (V) E1-05 (VMAX) E1-13 (V Base) E1-08 (VC) E1-10 (VMIN) E1-09 (FMIN) E1-07 (FB) E1-06 (FA) E1-04 (FMAX) Frequency (Hz) Fig 6.67 User-Set V/f Pattern Setting Precautions When the setting is to user-defined V/f pattern, beware of the following points. • When changing control method, constants E1-07 to E1-10 will change to the factory settings for that control method. • Be sure to set the four frequencies as follows: E1-04 (FMAX) ≥ E1-06 (FA) > E1-07 (FB) ≥ E1-09 (FMIN) 6-126 Individual Functions Torque Control With flux vector control or open-loop vector 2 control, the motor's output torque can be controlled by a torque reference from an analog input. To control torque, set d5-01 to 1 or set multi-function contact inputs H1- to 71 (Speed/Torque control) and turn ON the contact. Related Constants Name Constant Number Description Setting Range Factory Setting Change during Operation 0: Speed control (C5-01 to C507) 1: Torque control This function is only available in flux vector control method. To use the function for switching between speed and torque control, set to 0 and set the multi-function input to “speed/torque control change.” 0 or 1 0 Set the torque reference filter primary delay time in ms units. This function can be used to adjust the noise of the torque control signal or the responsiveness with the host controller. When oscillation occurs during torque control, increase the set value. 0 to 1000 Set the speed limit command method for the torque control method. 1: The analog input limit from a 1 or 2 frequency reference Speed Limit Sel 2: Limited by d5-04 constant setting values. Display Torque control selection d5-01 Torq Control Sel Torque reference delay time d5-02 Torq Ref Filter Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No No No No A A 29AH 0* No No No No A A 29BH 1 No No No No A A 29CH -120 to +120 0 No No No No A A 29DH 0 to 120 10 No No No No A A 29EH Speed limit selection d5-03 Speed limit d5-04 d5-05 Speed Lmt Value Set the speed limit during torque control as a percentage of the maximum output frequency. This function is enabled when d503 is set to 2. Directions are as follows: +: Run Command direction -: Opposite of Run Command Speed limit bias Set the speed limit bias as a percentage of the maximum output frequency. Bias is applied to the specified Speed Lmt Bias speed limit. It can be used to adjust the margin for the speed limit. 6-127 Name Constant Number d5-06 d5-07 Display Rotation direction limit operation selection Signal level selection (terminal A3) Term A3 Signal H3-05 Factory Setting Change during Operation 0 to 1000 0 0: Disabled 1: Enabled Usually, use a setting of 1 (enabled). Be sure to enable this setting when rotating the motor in the same direction as the speed limit (winding operation). 0 or 1 0: 0 to 10V 1: -10 to 10V [11-bit + polarity (positive/ negative) input] Multi-function analog input (terminal A3) function selection Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No No No No A A 29FH 1 No No No No No A 2A6H 0 or 1 0 No A A A A A 413H Select multi-function analog input 0 to 1F function for terminal A3. 2 No A A A A A 414H Description Speed/torque Set the delay time from inputting control the multi-function input “speed/ switching timer torque control change” (from ON to OFF or OFF to ON) until the control is actually changed in ms units. This function is enabled when the multi-function input “speed/ torque control change” is set. In Ref Hold Time the speed/torque control switching timer, the analog inputs hold the values of when the “speed/ torque control change” changes. Always be sure to allow time for this process to finish completely. Drctn SpdLmt Sel H3-04 Setting Range Terminal A3 Sel H3-06 H3-07 H3-08 H3-09 Gain (terminal A3) Sets the input gain (level) when 10 V is input. Set according to the 100% value selected from H3-05. 0.0 to 1000.0 100.0 % Yes A A A A A 415H Sets the input gain (level) when 0 V is input. Set according to the 100% value selected from H3-05. -100.0 to +100.0 0.0% Yes A A A A A 416H 0: 0 to 10V 1: -10V to 10V 2: 4 to 20 mA (9-bit input). Switch current and voltage input Term A2 Signal using the switch on the control panel. 0 to 2 2 No A A A A A 417H Select multi-function analog input 0 to 1F function for terminal A2. 0 No A A A A A 418H Terminal A3 Gain Bias (terminal A3) Terminal A3 Bias Signal level selection (terminal A2) Multi-function analog input (terminal A2) function selection Terminal A2 Sel 6-128 Individual Functions Name Constant Number H3-10 H3-11 Setting Range Factory Setting Change during Operation Sets the input gain (level) when 10 V (20 mA) is input. Set according to the 100% value for the function set for H3-09. 0.0 to 1000.0 100.0 % Sets the input gain (level) when 0 V (4 mA) is input. Set according to the 100% value for the function set for H3-09. -100.0 to +100. 0 0.0% Description Display Gain (terminal A2) Terminal A2 Gain Bias (terminal A2) Terminal A2 Bias Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 Yes A A A A A 419H Yes A A A A A 41AH * The factory setting will change when the control method is changed. The flux vector factory setting is given. Multi-function Contact Input Functions (H1-01 to H1-10) Control Methods Setting Value Function V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 71 Speed/torque control change (ON: Torque control) No No No Yes Yes 78 Polarity Reverse Command for external torque reference No No No Yes Yes Multi-function Contact Output Functions (H2-01 to H2-05) Control Methods Setting Value 32 Function Speed control circuit operating for torque control (except when stopped). The external torque reference will be limited if torque control is selected. Output when the motor is rotating at the speed limit. V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No No No Yes Yes Multi-function Analog Inputs (H3-05, H3-09) Control Methods Setting Value Function V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 0 Add to terminal A1 Yes Yes Yes Yes Yes 13 Torque reference/torque limit at speed control No No No Yes Yes 14 Torque compensation No No No Yes Yes Monitor Function Name Constant Number U1-09 Display Control Methods Description Torque referMonitor in internal torque ence reference value for vector Torque Ref- control. erence Output Signal Level During Multi-Function Analog Output Min. Unit 10 V: Motor rated torque (-10 to 10 V possible) 0.1 % V/f V/f with PG Open Loop Vector 1 Flux Vector No No A A Open MEMO BUS Loop RegVecister tor 2 A 48H 6-129 Inputting Torque References and Torque Reference Directions The torque reference can be changed according to an analog input by setting H3-09 (Multi-function analog input terminal A2 selection) or H3-05 (Multi-function analog input terminal A3 selection) to 13 (torque reference) or 14 (torque compensation). The torque reference input methods are listed in the following table. Torque Reference Input Method Reference Location Between A3 and AC Selection Method H3-04 = 1 H3-05 = 13 Set H3-04 to 0 for a 0 to 10-V torque reference. To switch the torque reference between positive and negative torque, set a multifunction analog input to 78. H3-08 = 1 H3-09 = 13 Set H3-08 to 0 for a 0 to 10-V torque reference. To switch the torque reference between positive and negative torque, set a multifunction analog input to 78. The input can be used for torque compensation by setting H3-09 to 14. Voltage input (-10 to 10 V) Between A2 and AC (Turn OFF pin 2 of SW1.) Remarks Current input (4 to 20 mA) Between A2 and AC (Turn ON pin 2 of SW1.) H3-08 = 2 H3-09 = 13 To switch the torque reference between positive and negative torque, set a multifunction analog input to 78. The input can be used for torque compensation by setting H3-09 to 14. Option board (AI-14B) (-10 to 10 V) F2-01 = 0 Between TC2 and TC4 H3-08 = 1 H3-09 = 13 The input can be used for torque compensation by setting H3-05 to 14. The direction of the torque output from the motor will be determined by the sign of the analog signal input. It does not depend on the direction of the Run Command. The direction of torque will be as follows: • Positive analog reference: Torque reference for forward motor rotation (counterclockwise as viewed from the motor output axis). • Negative analog reference: Torque reference for reverse motor rotation (clockwise as viewed from the motor output axis). Application Precautions If the analog signal input level is 0 to 10 V or 4 to 20 mA, a forward torque reference will not be applied. To apply reverse torque, use an input level of -10 V to 10 V or switch the direction using a multi-function input set to 78 (polarity Reverse Command for external torque reference). 6-130 Individual Functions Torque compensation from analog input Torque reference from analog input Torque primary delay filter d5-02 + Speed limit from analog input from terminal A1 1 + Speed limit d5-04 − Priority circuit Speed controller (ASR) Internal torque reference Torque limit + + Refer to torque limit setting via constants and analog input 2 d5-03 Speed limit bias d5-05 Speed limiter Speed feedback Fig 6.68 Torque Control Block Diagram Speed Limiter and Priority Circuit (Speed Limit Function) If the external torque reference and load are not balanced during torque control, the motor will accelerate in either the forward or reverse direction. The speed limit function is used to limit the speed to a specified value and it consists of the speed limiter circuit and priority circuit. When the motor speed exceeds the speed limit value during torque control, the speed limiter circuit generates the suppression torque proportional to the speed above the limit value and adds to the torque reference. The priority circuit switches the internal torque reference to ASR output so that the motor speed does not exceed the speed limit value. Application Precautions There are two ways to set a speed limit: using an input from an analog input terminal and setting a speed limit in d5-04. The inputs methods for a speed limit are listed in the following table. Speed Limit Input Method Location of Reference Constant Settings Set in d5-04 d5-03 = 2 Between A1 and AC b1-01 = 1 H3-01 = 1 Voltage input (-10 to 10 V) Remarks Set H3-01 to 0 if the speed limit is always to be positive. Between A2 and AC b1-01 = 0 H3-08 = 1 H3-09 = 1 The value will be added to the value input on A1 to determine the speed limit. Set H3-03 to 0 if the speed limit input on A2 is always to be positive. Turn OFF (V side) pin 2 of DIP switch S1 on the terminal board. Current input (4 to 20 mA) Between A2 and AC b1-01 = 0 H3-08 = 2 H3-09 = 1 The value will be added to the value input on A1 to determine the speed limit. Turn ON (I side) pin 2 of DIP switch S1 on the terminal board. Option board (AI-4B) (-10 to 10 V) b1-01 = 3 Between TC1 and TC4 F2-01 = 0 If H3-09 is set to 0, the sum of the input between TC2 and TC4 will be added the input between TC1 and TC4 to determine the speed limit. 6-131 The direction in which speed is controlled is determined by the sign of the speed limit signal and the direction of the Run Command. • Positive voltage applied: The speed in the forward direction will be limited for forward operation. IMPORTANT • Negative voltage applied: The speed in the reverse direction will be limited for reverse operation. If the direction of motor rotation and the command direction are not the same, speed will be limited to 0 as long as b5-05 is set to 0. Setting Speed Limit Bias The same speed limit bias can be set for the forward and reverse side, and is different from the speed limit. Set d5-04 to 0, and set the speed limit bias (d5-05) as a percentage of the maximum output frequency. When setting both forward and reverse speed limit biases to 50%, set the speed limit to 0 (d5-03 = 2, d5-04 = 0, d5-05 = 50). The torque control range with these settings is between -50 to +50% of the speed. When using the speed limit together with the speed limit bias, the torque control range will be limited by the speed limit + the speed limit biases on the forward and reverse sides of the speed limit range. When the forward speed limit is set to 50% and the speed limit bias to 10%, the torque control range will be as shown in the figure below unless the priority circuit is taken into consideration. Forward torque ∆N % Reverse run Forward run Forward speed limit d5-04 50 % Speed limit bias d5-05 10 % ∆N will be set as follows Torque reference [%] At motoring operation: C5-01 Reverse torque At regenerative operation: The smaller vaue Torque reference [%] or d5-05 C5-04 Fig 6.69 Setting Speed Limit Bias Torque Limit Operation Examples Operation examples will be described separately for winding operation, in which the speed and motor torque are in the same directions, and rewinding operation, in which the speed and motor torque are in opposite directions. Winding Operation In a winding operation, the line (speed) and torque generated by the motor are in the same direction. For the winding operation, both the speed limit and the torque reference input are positive. The motor will accelerate when the torque reference input is larger than the load and will decelerate when it is smaller than the load. If the motor turns faster than the speed limit, a negative compensation value is output from the speed limiter circuit. When the speed then drops below the speed limit, a positive compensation value is output. The torque compensation is proportional to the ASR proportional gain. When the sum of the torque reference and the torque compensation output by the speed limiter is the same as the actual load, the motor will stop accelerating and run at a constant speed. 6-132 Individual Functions Rewinding Operation In a rewinding operation, the line (speed) and torque generated by the motor are in the opposite directions. (In this example, we’ll assume that the line speed is positive and the torque reference input is negative.) For the rewinding operation, the speed limit is positive and the torque reference input is negative. If the motor turns faster than the speed limit, a negative compensation value is output from the speed limiter circuit. If the motor is rotating in reverse, a negative compensation value is output. If the speed is 0 or is below the speed limit, a 0 compensation value is output. In this way, the output from the speed limiter is used to maintain the motor speed between 0 and the speed limit. When the sum of the torque reference and the torque compensation output by the speed limiter is the same as the actual load, the motor will stop accelerating and run at a constant speed. Winding Operation N T Line direction N T X Configuration Rewinding Operation T N Line direction X T N X X Line direction M Normal Rotation Direction M Forward M Reverse M Forward Line direction Reverse Torque Reference Polarity (TREF) Speed Limit Polarity (SLIM) Torque limit Torque Torque limit ∆N Torque limit Torque Torque limit Torque TREF ∆N (d5-05) (d5-05) SLIM SLIM 0 0 Generated Torque 0 Speed SLIM Speed ∆N Speed (d5-05) TREF TREF Torque limit N(%) = TREF(%) C5-01 Torque TREF ǍN N(%) = Torque limit 0 Speed (d5-05) Torque limit Torque limit TREF(%) C5-01 SLIM The lower value of ∆N(%) = TREF(%) or d5-05(%) C5-01 The lower value of ∆N(%) = TREF(%) or d5-05(%) C5-01 Rotation Direction Limit Operation Selection (Valid Only for PRG: 102 in Open-loop Vector 2 Control) In applications where the machine is not rotated in the opposite direction to the sign of the speed limit (i.e., in winding operation), use with d5-07 set to 1. If the sign of the calculated speed is the opposite to that of the speed limit, a torque will be output to prevent the motor from accelerating in the opposite direction. Torque Reference Adjustment Consider the following information when adjusting the torque. Torque Reference Delay Time: d5-02 The time constant of the primary filter in the torque reference section can be adjusted. This constant is used to eliminate noise in the torque reference signal and adjust the responsiveness to the host controller. Increase the setting if oscillation occurs during torque control. 6-133 Setting the Torque Compensation Set multi-function analog input A2 or A3 to torque compensation (setting 14). When the amount of torque loss for mechanical loss or other factor at the load is input to one of these terminals, it is added to the torque reference to compensate for the loss. The direction of torque will be as follows: • Positive voltage (current): Torque compensation reference for forward motor rotation (counterclockwise as viewed from the motor output axis). • Negative voltage: Torque compensation reference for reverse motor rotation (clockwise as viewed from the motor output axis). Since the polarity of the voltage input determines the direction, only forward torque compensation can be input when the 0 to 10 V or 4 to 20 mA signal level has been selected. If you want to input reverse torque compensation, be sure to select the -10 to 10 V signal level. Speed/Torque Control Switching Function It is possible to switch between speed control and torque control when one of the multi-function inputs (H1-01 to H1-10) is set to 71 (Speed/Torque Control Change). Speed control is performed when the input is OFF and torque control is performed when the input is ON. Set d5-01 to switch speed/torque control. 6-134 Individual Functions Setting the Speed/Torque Control Switching Timer The delay between a change in the speed/control switching function input (ON to OFF or OFF to ON) and the corresponding change in the control method can be set in d5-06. During the timer delay, the value of the 3 analog inputs will retain the values they had when the ON/OFF status of speed/torque control switching signal was changed. Use this delay to complete any changes required in external signals. Application Precautions • The frequency reference (during speed control) is set in b1-01. The speed limit during torque control is set in d5-03. • If the torque reference has been assigned to a multi-function analog input, terminal A2, or terminal A3, the input function changes when the control method is switched between torque control and speed control. During speed control: The multi-function analog input terminal is used as the torque limit input. During torque control: The multi-function analog input terminal is used as the torque reference input. • When the Run Command turns OFF, the control method when stopped will be for speed control. Even from the torque control method, the system will automatically change to speed control and decelerate to a stop when the Run Command turns OFF. • When A1-02 (control method selection) is set to 3 (flux vector control), the speed/torque change command (a setting of 71) can be set for a multi-function input (H1-01 to H1-10) to switch between speed and torque control during operation. An example is shown below. Terminal No. User Constant No. Factory Setting Setting S8 H1-06 8 71 Speed/torque control change b1-01 1 1 Frequency reference selection (terminals A1, A2) d5-03 1 1 Speed limit (terminals A1, A2) H3-05 0 13 Torque reference/torque limit A1 A3 Function A timing chart for switching between speed and torque control is shown in the following figure. CLOSED OPEN Speed/torque change signal (terminal S8 input) CLOSED OPEN Run Run Command Control mode Stop Speed Torque Speed Terminal A3 input Speed (decel to stop) Speed limit Speed limit Terminal A1 input Torque Speed reference Speed reference Torque limit Torque limit Torque reference Torque reference Fig 6.70 Speed/Torque Control Switching Time Chart. 6-135 Speed Control (ASR) Structure Speed control (ASR) during vector control adjusts the torque reference so that the deviation between the speed reference and the estimated speed (PG feedback or speed estimator) is 0. Speed control (ASR) during V/ f control with a PG adjusts the output frequency so that the deviation between the speed reference and the estimated speed (PG feedback or speed estimator) is 0. The following block diagram shows the structure of the speed control for vector or V/f control with a PG. Torque limits C5-01, C5-03 Frequency reference + + − Detected speed Estimated speed + I limit I Torque reference Primary filter P C5-06 (C5-10) L7-01 to L7-04 C5-08 C5-02, C5-04 Speed Control Block Diagram for Vector Control Output frequency + Frequency reference + Limit Detected speed − + Change rate limiter + P + I C5-01 C5-03 C5-05 C5-02, C5-04 Speed Control Block Diagram for V/f Control with a PG Fig 6.71 Speed Control Block Diagrams Related Constants Name Constant Number C5-01 C5-02 Display Description ASR proportional (P) Sets the proportional gain of the speed gain 1 loop (ASR.) ASR P Gain 1 ASR integral (I) time 1 ASR I Time 1 6-136 Control Methods Sets the integral time of the speed loop (ASR) in 1-second units. Setting Range Change Factory during Setting Operation 0.00 to 300.00 20.00 *2 0.000 to 10.000 *1 0.500 s*1 Open MEMO Loop BUS RegVecister tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector Yes No A No A A 21BH Yes No A No A A 21CH Individual Functions Name Constant Number Display C5-03 ASR proportional (P) gain 2 ASR P Gain 2 C5-04 ASR limit ASR Limit ASR primary delay time C5-06 ASR Delay Time C5-07 ASR switching frequency ASR Gain SW Freq C5-08 Description Usually setting is not necessary. Set to change the rotational speed gain. ASR integral (I) limit ASR I Limit ASR primary delay time 2 C5-10 ASR Delay Time2 Setting Range Factory Setting 0.00 to 300.00 20.00 *1 *2 Open MEMO Loop BUS RegVecister tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector Yes No A No A A 21DH Yes No A No A A 21EH No No A No No No 21FH No No No No A A 220H P, I P=C5-01 I=C5-02 ASR integral (I) time 2 ASR I Time 2 C5-05 Control Methods Change during Operation P=C5-03 I=C5-04 0 E1-04 Motor speed (Hz) 0.000 to 10.000 0.500 s*1 Sets the upper limit for the compensation frequency for the speed control loop (ASR) to a percentage of the maximum output frequency. 0.0 to 20.0 Sets the filter time constant for outputting torque references from the speed control loop (ASR). It is set in 1-second units. With open-loop vector 2 control, this setting is enabled only for speeds in the range 0 to 35 Hz. Usually setting is not necessary. 0.000 to 0.500 Set the frequency for switching between Proportion Gain 1, 2 and Integral Time 1, 2 in Hz units. Speed control (ASR) proportional gain switching for a multi-function input takes priority. 0.0 to 400.0 0.0 Hz No No No No A A 221H Set the upper limit of the speed control loop integral as a percentage of the value at the rated load. 0 to 400 400% No No No No A A 222H Sets the filter time constant for outputting torque references from the speed control loop (ASR). It is set in 1-second units. With open-loop vector 2 control, this setting is enabled only for speeds greater than 35 Hz. Usually setting is not necessary. 0.000 to 0.500 0.010 s No No No No No A 231H 5.0% 0.004s *1 * 1. When the control method is changed, the factory settings will change. The flux vector factory settings are given. * 2. The setting range for flux vector and open-loop vector 2 controls is 1.00 to 300.00. Multi-function Contact Input Functions (H1-01 to H1-10) Control Methods Setting Value Function V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 D Speed control disable setting for V/f control with PG OFF: Use speed control V/f control with PG ON: Do not use speed control for V/f control with PG No Yes No No No E Speed control integral reset Enables switching between PI and P control for the speed control loop. No No No Yes Yes 77 Speed control (ASR) proportional gain switch (switching between C5-01 and C5-03) OFF: Use proportional gain in C5-01 ON: Use proportional gain in C5-03 No No No Yes Yes 6-137 Speed Control (ASR) Gain Adjustment for Vector Control Use the following procedure to adjust C5-01 and C5-03 with the mechanical system and actual load connected. At zero-speed, increase C5-01 (ASR P Gain 1) until there is no oscillation. At zero-speed, decrease C5-02 (ASR I Time 1) until there is no oscillation. Does oscillation develop when the motor operates at the maximum normal operating speed? YES Decrease C5-01 (ASR P Gain 1). NO Adjustment completed. (When there is higher-level position control, adjust the position loop gain so that overshooting/undershooting doesn't occur.) Increase C5-02 (ASR I Time 1). Fine Adjustments When you want even finer gain adjustment, adjust the gain while observing the speed waveform. Constant settings like those shown in the following table will be necessary to monitor the speed waveform. Constant No. Name Setting H4-01 Multi-function analog output 1 terminal FM monitor selection 2 H4-02 Multi-function analog output 1 terminal FM output gain 1.00 H4-03 Multi-function analog output 1 terminal FM bias 0.0 H4-04 Multi-function analog output 2 terminal AM monitor selection H4-05 Multi-function analog output 2 terminal AM output gain 1.00 H4-06 Multi-function analog output 2 terminal AM bias selection 0.00 H4-07 Multi-function analog output 1 terminal signal level selection 1 H4-08 Multi-function analog output 2 terminal signal level selection 1 5 Explanation Settings that allow multi-function analog output 1 to be used to monitor the output frequency. Settings that allow multi-function analog output 2 to be used to monitor the motor speed. Settings that allow a -10 to 10 V signal range to be monitored. The multi-function analog outputs have the following functions with these constant settings. • Multi-function analog output 1 (terminal FM): Outputs Inverter's output frequency (-10 to 10 V). • Multi-function analog output 2 (terminal AM): Outputs actual motor speed (-10 to 10 V). Terminal AC is the multi-function analog output common. We recommend monitoring both the output frequency and the motor speed to monitor the response delay or deviations from the reference value, as shown in the following diagram. 6-138 Individual Functions Adjusting ASR Proportional Gain 1 (C5-01) This gain setting adjusts the responsiveness of the speed control (ASR). The responsiveness is increased when this setting is increased. Usually this setting is higher for larger loads. Oscillation will occur if this setting is increased too much. The following diagram shows the type of changes that can occur in the response when the ASR proportional gain is changed. Motor speed The proportional gain is high. (Oscillation occurs when the gain is too high.) The proportional gain is low. Time Fig 6.72 Responsiveness for Proportional Gain Adjusting ASR Integral Time 1 (C5-02) This constant sets the speed control (ASR) integral time. Lengthening the integral time lowers the responsiveness, and weakens the resistance to external influences. Oscillation will occur if this setting is too short. The following diagram shows the type of changes that can occur in the response when the ASR integral time is changed. Motor speed Short integral time Long integral time Time Fig 6.73 Responsiveness for Integral Time 6-139 Different Gain Settings for Low-speed and High-speed Switch between low-speed and high-speed gain when oscillation occurs because of resonance with the mechanical system at low speed or high speed. The proportional gain P and integral time I can be switched according to the motor speed, as shown below. P = C5-01 I = C5-02 P, I P = C5-03 I = C5-04 C5-07 (Low speed) Motor speed (Hz) If C5-07 is set to 0, P = C5-01 and I = C5-02. Fig 6.74 Low-speed and High-speed Gain Settings Setting the Gain Switching Frequency (C5-07) Set the switching frequency to about 80% of the motor operating frequency or the frequency at which oscillation occurs. Low-speed Gain Adjustments (C5-03, C5-04) Connect the actual load and adjust these constants at zero-speed. Increase C5-03 (ASR proportional gain 2) until there is no oscillation. Decrease C5-04 (ASR integral time 2) until there is no oscillation. High-speed Gain Adjustments (C5-01, C5-02) Adjust these constants at normal operating speed. Increase C5-01 (ASR proportional gain 1) until there is no oscillation. Decrease C5-02 (ASR integral time 1) until there is no oscillation. Refer to Fine Adjustments on page 6-138 for details on making fine adjustments of high-speed operation. ASR Proportional Gain Switch Setting When one of the multi-function inputs (H1-01 to H1-10) is set to 77, the input can be used to switch between C5-01 (proportional gain 1) and C5-03 (proportional gain 2). Proportional gain 2 is used when the multi-function input is ON. This input has higher priority than the ASR switching frequency set in C5-07. ON ASR Gain Switch signal (a multi-function input) OFF Proportional gain determined by motor speed. Proportional gain (P) C5-03 gain setting C5-02 C5-02 The gain is changed linearly in integral time 1 (C5-02). Fig 6.75 ASR Proportional Gain Switch 6-140 Individual Functions Precautions for Open-loop Vector 2 Control (PRG: 102 only) • The ASR primary delay time setting for open-loop vector 2 control is divided between constants C5-06 and C5-10. The constant that is used depends on the size of the operating frequency. If the operating frequency is between 0 and 35 Hz, adjust the setting using C5-06, and if the operating frequency is greater than 35 Hz, adjust the setting using C5-10. • To increase the speed response, adjust the gain with reference to the explanations on page 4-19 in Chapter 4 Trial Operation. Gain Adjustment for Speed Control during V/f Control with PG When using V/f control with PG, set the proportional gain (P) and the integral time (I) at E1-09 (minimum output frequency) and E1-04 (maximum output frequency). Speed Control Gain Integral Time Adjustment for V/f Control with PG shows how the proportional gain and integral time change in linear fashion based on the speed. P and I setting P = C5-01 I = C5-02 P = C5-03 I = C5-04 0 E1-09 Min. output frequency Motor speed (Hz) E1-04 Max. output frequency Fig 6.76 Speed Control Gain Integral Time Adjustment for V/f Control with PG Gain Adjustments at Minimum Output Frequency Operate the motor at the minimum output frequency. Increase C5-03 (ASR proportional gain 2) to a level where there is no oscillation. Decrease C5-04 (ASR integral time 2) to a level where there is no oscillation. Monitor the Inverter's output current and verify that it is less than 50% of the Inverter rated current. If the output current exceeds 50% of the Inverter's rated current, decrease C5-03 and increase C5-04. Gain Adjustments at Maximum Output Frequency Operate the motor at the maximum output frequency. Increase C5-01 (ASR proportional gain 1) to a level where there is no oscillation. Decrease C5-02 (ASR integral time 1) to a level where there is no oscillation. Fine Adjustments When you want even finer gain adjustment, adjust the gain while observing the speed waveform. The adjustment method is the same as that for vector control. Enable integral operation during acceleration and deceleration (by setting F1-07 to 1) when you want the motor speed to closely follow the frequency reference during acceleration and deceleration. Reduce the setting of C5-01 if overshooting occurs during acceleration, and reduce the setting of C5-03 and increase the setting of C5-04 if undershooting occurs when stopping. If overshooting and undershooting cannot be eliminated by adjusting only the gain, reduce the value of C5-05 speed control and reduce the limit of the frequency reference compensation value. 6-141 Increasing the Speed Reference Response (Feed Forward Control) Use feed forward control to increase the responsiveness to speed references. This function is effective for machines for which the ASR gain cannot be increased to a large value because doing so would result in vibrations. There is also the additional effect of making the system less prone to overshoot. This function is valid only in flux vector and open-loop vector 2 controls. Overshooting when acceleration completed is being suppressed Overshooting Rotation speed (min-1) Rotation speed (min-1) Time(s) Feed forward control Time(s) Conventional speed control Overshooting control effect Fig 6.77 Overshooting Control Effect Related Constants Name Constant Number N5-01 Description Display Feed forward control selection Feedfoward Sel Motor acceleration time Select the feed forward control. 0: Disabled 1: Enabled Motor Accel Time 2π x J [kgm2] x Nr [min-1] [s] ta = 60 x T100 [N x m] N5-03 Feedfoward Gain 0 *1 Change during Operation Control Methods V/f Open Loop Vector 1 Flux Vector Open Loop Vector 2 No No No No A A 5B0H 0.001 to 10.000 0.178 s*2 No No No No A A 5B1H No No No No A A 5B2H P [kW] 60 × 103 [N x m] x 2π Nr [min-1] Set the proportional gain for feed forward control. Speed reference response will increase as the setting of N5-03 is increased. 0.00 to 100.00 1.0 * 1. When the control method is changed, the factory setting will change. The flux vector factory setting is given. * 2. The factory setting depends on the Inverter capacity. The value for a 200 V Class Inverter of 0.4 kW is given. 6-142 MEMO BUS Register V/f with PG However, T100 = Feed forward proportional gain 0 or 1 Factory Setting Set the time required to accelerate the motor at the rated torque (T100) to the rated speed (Nr). J: GD2/4, P: Motor rated output N5-02 Setting Range Individual Functions Feed Forward Control Structure • The following block diagram shows the speed controller (ASR) and the feed forward control structure. Frequency reference N5-02, N5-03 U1-45 Feed forward controller U1-44 Torque limit Primary filter Speed controller (ASR) C5-06 (C5-10) U1-05 Secondary current reference L7-01 to L7-04 Detected speed (Calculated speed) Fig 6.78 Structure of Speed Controller (ASR) and Feed Forward Control Setting Precautions • When N5-02 (Motor acceleration time) is not properly set, the acceleration time may not increase. The fac- tory setting of N5-02 depends on the Inverter capacity. When the Inverter capacity is different from the motor capacity, calculate an appropriate acceleration time using the equation given in N5-02 of Chapter 5 User Constants or set the time that corresponds to the motor capacity referring to Factory Settings that Change with the Control Method (A1-02) (Page 5-87) • When setting the feed forward proportional gain (N5-03), take the inertia of the motor to be equivalent to 1. If the speed reference response is slow, increase the feed forward proportional gain (N5-03). If overshoot occurs with the actual speed, or if a negative torque reference is output when acceleration is completed, reduce the feed forward proportional gain (N5-03). • When using the droop control function (i.e., if b7-01 is not set to 0.0), disable feed forward control (i.e., set N5-01 to 0). Droop Control Function Droop control is a function that allows the user to set the amount of motor slip. When a single load is operated with two motors (such as in a crane conveyor), a high-resistance motor is normally used. This is to use torque characteristics that exhibit proportion movements due to changes in the secondary resistor to maintain torque balance with the load and overall speed balance with the load. If droop control is used, a high-resistance motor characteristics can be set for a general-purpose motor. The balance of the load is very different with different amounts of slip. Motor A's torque characteristics Torque TA Torque Motor B's torque characteristics TA Load torque TB Motor B's torque characteristics Motor A's torque characteristics Load torque TB The difference between TA and TB is getting larger. Reference Speed speed Load balance when using a general-purpose motor The difference between TA and TB is getting smaller. Reference Speed speed Load balance when using a high-purpose motor Fig 6.79 Droop Control Function 6-143 Related Constants Name Constant Number Description Display Factory Setting Change during Operation 0.0 to 100.0 0.0 0.03 to 2.00 0.05 s Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 Yes No No No A A 1CAH No A A A A A 1CBH Droop control gain b7-01 b7-02 Sets the slip as a percentage of maximum frequency when the maximum output frequency is specified and the rated torque occurs. Droop Quantity Droop-control is not performed when the setting is 0.0. Setting Range Droop control delay time Droop Delay Time Droop control responsiveness constant When hunting or oscillation occurs, increase the value. Setting Precautions • Droop control is disabled if b7-01 is set to 0.0. • Set b7-01 to the amount of slip as the percentage of slip when the maximum output frequency is input and the rated torque is generated. • Constant b7-02 is used to adjust the responsiveness of droop control. Increase this setting if oscillation or hunting occur. • Disable the feed forward control (N5-01 = 0) when using the droop control function. Setting the Droop Control Gain Set the droop control gain as the speed reduction at a 100% motor torque, as a percentage of the maximum output frequency. Torque b7-01 100% Speed 0 Speed reference Fig 6.80 Droop Control Gain 6-144 Individual Functions Zero-servo Function The zero-servo function holds the motor when the motor is stopped in what is call a zero-servo status. This function can be used to stop the motor even with an external force acts on the motor or the analog reference input is offset. The zero-servo function is enabled when one of the multi-function inputs (H1-01 to H1-10) is set to 72 (zeroservo command). If the zero-servo command is ON when the frequency (speed) reference falls below the zerospeed level, a zero-servo status is implemented. Related Constants Name Constant Number Display b2-01 Zero-speed level (DC injection braking starting frequency) DCInj Start Freq b9-01 Description Used to set the frequency which starts DC injection braking in units of Hz when deceleration to stop is selected. When b2-01 is less than E1-09, E1-09 becomes the DC injection braking starting frequency. (For flux vector control, zerospeed control from B2-01) Zero-servo gain Adjust the strength of the zeroservo lock. Enabled when the zero-servo command is set for a multi-function input. When the zero-servo command has been input and the frequency reference drop below Zero Servo excitation level (b2-01), a posiGain tion control loop is created and the motor stops. Increasing the zero-servo gain in turn increases the strength of the lock. Increasing it by too much will cause oscillation. Zero-servo completion width b9-02 Zero Servo Count Sets the output width of the Plock completion signal. Enabled when the “zero-servo completion (end)” is set for a multi-function input. The zeroservo completion signal is ON when the current position is within the range (the zero-servo position + zero-servo completion width.) Set the allowable position displacement from the zero-servo position to 4 times the pulse rate of the PG (pulse generator, encoder) in use. Setting Range Factory Setting Change during Operation 0.0 to 10.0 0.5 Hz 0 to 100 0 to 16383 Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 189H 5 No No No No A No 1DAH 10 No No No No A No 1DBH 6-145 Multi-function Contact Input Functions (H1-01 to H1-10) Control Methods Setting Value 72 Function Zero-servo command (ON: Zero-servo) V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No No No Yes No Multi-function Contact Output Functions (H2-01 to H2-05) Control Methods Setting Value 33 Function Zero-servo end ON: Current position is within zero-servo start position ± the zero-servo end width. V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No No No Yes No To output the zero-servo status externally, assign the Zero-servo End signal (setting 33) to one of the multifunction outputs (H2-01 to H2-05). Monitor Function Name Constant Number U1-35 Description Display Zero-servo movement pulses Zero Servo Pulse Shows the number of PG pulses times 4 for the movement range when stopped at zero. Setting Range Factory Setting Change during Operation (Cannot be output.) 1 No Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector No No A No Time Chart A time chart for the zero-servo function is given in Time Chart for Zero-servo. ON Run Command Zero servo command OFF ON Frequency (speed) reference Excitation level b2-01 Motor speed Zero Servo End signal Zero-servo status Fig 6.81 Time Chart for Zero-servo 6-146 OFF Open Loop Vector 2 MEMO BUS Register 62H Individual Functions Application Precautions • Be sure to leave the Run Command input ON. If the Run Command is turned OFF, the output will be inter- rupted and the zero-servo function will become ineffective. • The holding force of the zero-servo is adjusted in b9-01. The holding force will increase if the value of the setting is increased, but oscillation and hunting will occur if the setting is too large. Adjust b9-01 after adjusting the speed control gain. • The zero-servo detection width is set as the allowable position offset from the zero-servo start position. Set 4 times the number of pulses from the PG. • The Zero-servo End signal will go OFF when the zero-servo command is turned OFF. Do not lock the servo for extended periods of time at 100% when using the zero-servo function. Inverter errors may result. Extended periods of servo lock can be achieved by ensuring that the current during the servolock is 50% or less or by increasing the Inverter capacity. IMPORTANT 6-147 Digital Operator Functions This section explains the Digital Operator functions. Setting Digital Operator Functions You can set Digital Operator-related constants such as selecting the Digital Operator display, multi-function selections, and copy functions. Related Constants Name Constant Number o1-02 Display Description Monitor selec- Sets the monitor item to be distion after power played when the power is turned up on. 1: Frequency reference 2: Output frequency Power-On 3: Output current Monitor 4: The monitor item set for o1-01 Setting Range Factory Setting Change during Operation 1 to 4 1 0 to 39999 Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 Yes A A A A A 501H 0 No A A A A A 502H 0 or 1 0 No No No No A A 503H 0 or 1 1 No A A A A A 505H Frequency units Sets the units that will be set and of reference set- displayed for the frequency referting and moni- ence and frequency monitor. tor 0: 0.01 Hz units 1: 0.01% units (Maximum output frequency is 100%) 2 to 39: o1-03 Display Scaling min−1 units (Sets the motor poles.) 40 to 39999: User desired display Set the desired values for setting and display for the max. output frequency. Set 4-digit number excluding the decimal point. Set the number of digits below the decimal point to display. Example: When the max. output frequency value is 200.0, set 12000 o1-04 o2-01 Setting unit for frequency constants related to Set the setting unit for frequency V/f characteris- reference-related constants. 0: Hz tics 1: min−1 V/f Display Unit LOCAL/ REMOTE key enable/disable Local/Remote Key 6-148 Sets the Digital Operator Local/ Remote Key 0: Disabled 1: Enabled (Switches between the Digital Operator and the constant settings.) Digital Operator Functions Name Constant Number o2-02 STOP key during control circuit terminal operation User constant initial value o2-03 User Defaults Frequency reference setting method selection o2-05 Operator M.O.P. Cumulative operation time setting Elapsed Time Set o2-10 Factory Setting Change during Operation Sets the Stop Key in the run mode. 0: Disabled (When the Run Command is issued from and external terminal, the Stop Key is disabled.) 1: Enabled (Effective even during run.) 0 or 1 1 Clears or stores user initial values. 0: Stores/not set 1: Begins storing (Records the set constants as user initial values.) 2: All clear (Clears all recorded user initial values) When the set constants are recorded as user initial values, 1110 will be set in A1-03. 0 to 2 When the frequency reference is set on the Digital Operator frequency reference monitor, sets whether the Enter Key is necessary. 0: Enter Key needed 1: Enter Key not needed When set to 1, the Inverter accepts the frequency reference without Enter Key operation. Fan operation time setting Fan ON Time Set Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 506H 0 No A A A A A 507H 0 or 1 0 No A A A A A 509H Sets the cumulative operation time in hour units. Operation time is calculated from the set values. 0 to 65535 0 hr No A A A A A 50BH Set the initial value of the fan operation time using time units. The operation time accumulates from the set value. 0 to 65535 0 hr No A A A A A 50EH Description Display Oper STOP Key o2-07 Setting Range Changing Frequency Reference and Display Units Set the Digital Operator frequency reference and display units using constant o1-03. You can change the units for the following constants using o1-03. • U1-01 (Frequency Reference) • U1-02 (Output Frequency) • U1-05 (Motor Speed) • U1-20 (Output Frequency after Soft Start) • d1-01 to d1-17 (Frequency references) Switching Monitors when the Power Supply Is ON Using constant o1-02, select the monitor item (U1- [status monitor]) to be displayed on the Digital Operator when the power supply is turned ON. For monitors that can be displayed, refer to U1- in Chapter 5 User Constants. 6-149 Setting Precautions If selecting monitor constants other than U1-01 (Frequency Reference), U1-02 (Output Frequency), and U103 (Output Current), first select the monitor items to be displayed in o1-01, and then set o1-02 to 4. Disabling the STOP Key If b1-02 (Operation Method Selection) is set to 1, 2, or 3, the Stop Command from the STOP Key on the Digital Operator is an emergency Stop Command. Set o2-02 to 0 to disable emergency Stop Commands from the STOP Key on the Digital Operator. Disabling the LOCAL/REMOTE Key Set o2-01 to 0 to disable the LOCAL/REMOTE Key on the Digital Operator. You cannot switch Inverter reference inputs set using reference inputs from the Digital Operator, b1-01 (Reference Selection), or b1-02 (Operation Method Selection). Initializing Changed Constant Values You can save the Inverter constant set values that you have changed as constant initial values. Change the set values from the Inverter factory settings, and then set o2-03 to 1. If, however, “Out of Memory MAX Param Change” is displayed on the Operator when changes in the settings of the constants are saved as initial values, do not attempt to register any further changes as initial values. Set A1-03 (Initialize) to 1110 to initialize the Inverter constants using the user-set initial values in memory. To clear the user-set initial values in memory, set o2-03 to 2. Setting the Frequency Reference using the UP and DOWN Keys without Using the Enter Key Use this function when inputting frequency references from the Digital Operator. When o2-05 is set to 1, you can increment and decrement the frequency reference using the UP and DOWN Keys without using the Enter Key. For example, enter the Run Command using a 0 Hz reference, and then continuously press the UP Key to increment the frequency reference by 0.01 Hz only for the first 0.5 s, and then by 0.01 Hz every 80 ms for 3 s thereafter. Press and hold down the UP Key for 3 s minimum to reach the maximum output frequency 10 s after that. The frequency reference that has been set will be stored in memory 5 s after the UP or DOWN Keys are released. Clearing Cumulative Operation Time Set the cumulative operation time initial value in time units in constant o2-07. Set o2-07 to 0 to clear U1-13 (Inverter Operating Time). Clearing Inverter Cooling Fan Operation Time Set the fan operation time initial value in time units in constant o2-10. Set o2-10 to 0 to clear U1-40 (Cooling Fan Operating Time). 6-150 Digital Operator Functions Copying Constants The Digital Operator can perform the following three functions using the built-in EEPROM (non-volatile memory). • Store Inverter constant set values in the Digital Operator (READ) • Write constant set values stored in the Digital Operator to the Inverter (COPY) • Compare constant set values stored in the Digital Operator with Inverter constants (VERIFY) Related Constants Name Constant Number o3-01 o3-02 Display Copy function selection Copy Function Sel Read permitted selection Copy Allowable Description Setting Range Factory Setting Change during Operation 0: Normal operation 1: READ (Inverter to Operator) 2: COPY (Operator to Inverter) 3: Verify (compare) 0 to 3 0 0: Read prohibited 1: Read permitted 0 or 1 0 Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 515H No A A A A A 516H 6-151 Storing Inverter Set Values in the Digital Operator (READ) To store Inverter set values in the Digital Operator, make the settings using the following method. Set 03-02 (Read permitted selection) to 1 (read permitted). Table 6.1 READ Function Procedure Step No. Digital Operator Display Explanation -ADV- 1 ** Main Menu ** Programming Press the Menu Key, and select advanced programming mode. -ADV- 2 Initialization Press the DATA/ENTER Key, and select the constants monitor display. A1 - 00=1 Select Language -ADV- 3 Display o3-01 (Copy Function Selection) using the Increment Key and Decrement Key. COPY Function o3 - 01=0 Copy Funtion Sel -ADV- 4 Copy Funtion Sel o3-01= 0 *0* Press the DATA/ENTER Key, and select the constants setting display. COPY SELECT -ADV- 5 Copy Funtion Sel o3-01= 1 *0* Change the set value to 1 using the Increment Key. INV→OP READ -ADV- 6 READ INV→OP READING Set the changed data using the DATA/ENTER Key. The READ function will start. -ADV- 7 READ READ COMPLETE If the READ function ends normally, End is displayed on the Digital Operator. -ADV- 8 Copy Funtion Sel o3 - 01=0 *0* The display returns to o3-01 when a key is pressed. COPY SELECT An error may occur while saving to memory. If an error is displayed, press any key to cancel the error display and return to the o3-01 display. Error displays and their meanings are shown below. (Refer to Chapter 7 Errors when Using the Digital Operator Copy Function.) Error Display PRE READ IMPOSSIBLE 6-152 Meaning You are attempting to set o3-01 to 1 while o3-02 is set to 0. Digital Operator Functions Error Display Meaning IFE Read data length mismatch or read data error. READ DATA ERROR RDE Tried to write constants to EEPROM on the Digital Operator, but unable to perform write operation. DATA ERROR Select READ Permitted Prevent overwriting the data stored in EEPROM in the Digital Operator by mistake. With o3-02 set to 0, if you set o3-01 to 1, and perform the write operation, PrE will be displayed on the Digital Operator, and the write operation will be stopped. Writing Constant Set Values Stored in the Digital Operator to the Inverter (COPY) To write constant set values stored in the Digital Operator to the Inverter, make the settings using the following method. Table 6.2 COPY Function Procedure Step No. Digital Operator Display Explanation -ADV- 1 ** Main Menu ** Programming Press the MENU Key, and select advanced programming mode. -ADV- 2 Initialization Press the DATA/ENTER Key, and select the constants monitor display. A1 - 00=1 Select Language -ADV- 3 Display o3-01 (Copy Function Selection) using the Increment Key and Decrement Key. COPY Function o3 - 01=0 Copy Funtion Sel -ADV- 4 Copy Funtion Sel o3-01= 0 *0* Press the DATA/ENTER Key, and select the constants setting display. COPY SELECT -ADV- 5 Copy Funtion Sel o3-01= 2 *0* Change the set value to 2 using the Increment Key. OP→INV WRITE -ADV- 6 COPY OP→INV COPYING Set the changed data using the DATA/ENTER Key. The COPY function will start. -ADV- 7 COPY COPY COMPLETE If the COPY function ends normally, End is displayed on the Digital Operator. 6-153 Table 6.2 COPY Function Procedure Step No. Digital Operator Display Explanation -ADV- Copy Funtion Sel 8 o3 - 01=0 The display returns to o3-01 when a key is pressed. *0* COPY SELECT During the copy operation, errors may occur. If an error is displayed, press any key to cancel the error display and return to the 03-01 display. Error displays and their meanings are shown below. (Refer to Chapter 7 Errors when Using Digital Operator Copy Function.) Error Display CPE ID UNMATCH VAE INV. KVA UNMATC CRE CONTROL UNMATCH CYE COPY ERROR CSE SUM CHECK ERROR Meaning Inverter product code and Inverter software number are different. Inverter capacity with which you are trying to copy, and the Inverter capacity stored in the Digital Operator are different. The Inverter control method in which you are trying to copy, and the Inverter control method stored in the Digital Operator are different. Comparison between the constant written to the Inverter and the constant in the Digital Operator shows they are different. After copying has ended, comparison between the sum value of the Inverter constant area and the sum value of the Digital Operator constant area shows they are different. Comparing Inverter Constants and Digital Operator Constant Set Values (VERIFY) To compare Inverter constants and Digital Operator constant set values, make the settings using the following method. Table 6.3 VERIFY Function Procedure Step No. Digital Operator Display Explanation -ADV- 1 ** Main Menu ** Programming Press the MENU Key. and select advanced programming mode. -ADV- 2 Initialization A1 - 00=1 Select Language 6-154 Press the DATA/ENTER Key, and select the constants monitor display. Digital Operator Functions Table 6.3 VERIFY Function Procedure (Continued) Step No. Digital Operator Display Explanation -ADV- 3 Display o3-01 (Copy Function Selection) using the Increment Key and Decrement Key. COPY Function o3 - 01=0 Copy Funtion Sel -ADV- 4 Copy Funtion Sel o3-01= 0 Press the DATA/ENTER Key, and select the function setting display. *0* COPY SELECT -ADV- 5 Copy Funtion Sel o3-01= 3 Change the set value to 3 using the Increment Key. *0* OP←→INV VERIFY -ADV- 6 VERIFY Set the changed data using the DATA/ENTER Key. The VERIFY function will start. DATA VERIFYING -ADV- 7 VERIFY If the VERIFY function ends normally, End is displayed on the Digital Operator. VERIFY COMPLETE -ADV- 8 Copy Funtion Sel o3 - 01=0 The display returns to o3-01 when a key is pressed. *0* COPY SELECT An error may occur during the comparison. If an error is displayed, press any key to cancel the error display and return to the o3-01 display. Error displays and their meanings are shown below. (Refer to Chapter 7 Errors when Using Digital Operator Copy Function.) Error Display VYE VERIFY ERROR CPE ID UNMATCH Meaning Verify error (Settings in the Digital Operator and the Inverter do not match). Inverter product code and Inverter software number are different. Application Precautions • When using the copy function, check that the following settings are the same between the Inverter and the Digital Operator. • Inverter product and type • Inverter capacity and voltage • Software number • Control method • Use the copy function off-line or with a communications option board removed. • A CPF03 fault (EEPROM error) can occur if the power is shut down while the Inverter constants are being copied. Do not shut down the power while copying the constants. 6-155 Prohibiting Writing Constants from the Digital Operator If you set A1-01 to 0, you can refer to and set the A1 and A2 constant groups, and refer to drive mode, using the Digital Operator. If you set one of the constants H1-01 to H1-10 (multi-function contact input terminal S3 to S12 function selection) to 1B (write constants permitted), you can write constants from the digital operator when the terminal that has been set is ON. When the set terminal is OFF, writing constants other than the frequency reference is prohibited. You can, however, reference constants. Name Constant Number A1-01 Display Description Constant access Used to set the constant access level level (set/read.) 0: Monitoring only (Monitoring drive mode and setting A1-01 and A1-04.) 1: Used to select user constant (Only constants set in A2-01 to A2-32 can be read and set.) Access Level 2: Advanced (Constants can be read and set in both quick programming mode and advanced programming (A) mode.) Setting Range Factory Setting Change during Operation 0 to 2 2 Yes Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A MEMO BUS Register 101H Setting a Password When a password is set in A1-05, if the set values in A1-04 and A1-05 do not match, you cannot refer to or change the settings of constants A1-01 to A1-03, or A2-01 to A2-32. You can prohibit the setting and referencing of all constants except A1-00 by using the password function in combination with setting A1-01 to 0 (Monitor only). Related Constants Name Constant Number A1-01 6-156 Display Description Constant access Used to set the constant access level level (set/read.) 0: Monitoring only (Monitoring drive mode and setting A1-01 and A1-04.) 1: Used to select user constant (Only constants set in A2-01 to A2-32 can be read and set.) Access Level 2: Advanced (Constants can be read and set in both quick programming mode and advanced programming (A) mode.) Setting Range Factory Setting Change during Operation 0 to 2 2 Yes Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A MEMO BUS Register 101H Digital Operator Functions Name Constant Number Description Display Factory Setting Change during Operation 0 to 9999 0 0 to 9999 0 Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 104H No A A A A A 105H Password A1-04 Password input when a password has been set in A1-05. This function write-protects some constants of the initialize mode. If the password is changed, A1-01 Enter Password to A1-03 and A2-01 to A2-32 constants can no longer be changed. (Programming mode constants can be changed.) Setting Range Password setting A1-05 Select Password Used to set a four digit number as the password. This constant is not usually displayed. When the Password (A104) is displayed, hold down the RESET Key and press the Menu Key and the password will be displayed. Setting Precautions Constant A1-05 cannot be displayed using normal key operations. To display A1-05, hold down the RESET Key and press the MENU Key while A1-04 is displayed. Displaying User-set Constants Only You can set and refer to constants necessary to the Inverter only, using the A2 constants (user-set constants) and A1-01 (Constants Access Level). Set the number of the constant to which you want to refer in A2-01 to A2-32, and then set A1-01 to 1. You can set and refer to constants set in A1-01 to A1-03 and A2-01 to A2-32 only, using advanced programming mode. Related Constants Name Constant Number Display User setting constants A2-01 to A2-32 User Param 1 to 32 Description Setting Range Factory Setting Change during Operation Used to set the constant numbers that can be set/read. Maximum 32. Effective when the Constant Access Level (A1-01) is set to User Program (1). Constants set in constants A2-01 to A2-32 can be set/read in programming mode. b1-01 to o3-02 - No Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A MEMO BUS Register 106H to 125H 6-157 Options This section explains the Inverter option functions. Performing Speed Control with PG This section explains functions with V/f control with PG. Related Constants Name Constant Number Display PG constant F1-01 PG Pulses/Rev Operation selection at PG open circuit (PGO) Open Loop Vector 1 Flux Vector Open Loop Vector 2 MEMO BUS Register 600 No No Q No Q No 380H 1 No No A No A No 381H Operation Sets the stopping method when an selection at overspeed (OS) fault occurs. overspeed (OS) 0: Ramp to stop (Deceleration stop using Deceleration Time 1, C1-02.) 1: Coast to stop 2: Fast stop (Emergency stop PG Overspeed using the deceleration time in Sel C1-09.) 3: Continue operation (To protect the motor or machinery, do not normally make this setting.) 0 to 3 1 No No A No A A 382H Sets the stopping method when a speed deviation (DEV) fault occurs. 0: Ramp to stop (Deceleration stop using Deceleration Time 1, C1-02.) 1: Coast to stop 2: Fast stop (Emergency stop using the deceleration time in C1-09.) 3: Continue operation (DEV is displayed and operation continued.) 0 to 3 3 No No A No A A 383H 0: Phase A leads with Forward Run Command. (Phase B leads with Reverse Run Command.) 1: Phase B leads with Forward Run Command. (Phase A leads with Reverse Run Command.) 0 or 1 0 No No A No A No 384H Operation selection at deviation F1-04 PG Deviation Sel PG rotation 6-158 Sets the number of PG (pulse generator or encoder) pulses. 0 to Sets the number of pulses per 60000 motor revolution. V/f V/f with PG 0 to 3 PG Fdbk Loss Sel F1-05 Setting Range Control Methods Sets the PG disconnection stopping method. 0: Ramp to stop (Deceleration stop using Deceleration Time 1, C1-02.) 1: Coast to stop 2: Fast stop (Emergency stop using the deceleration time in C1-09.) 3: Continue operation (To protect the motor or machinery, do not normally make this setting.) F1-02 F1-03 Description Change Factory during Setting Operation PG Rotation Sel Options Name Constant Number Description Display Setting Range Factory Setting Change during Operation 1 to 132 1 0 or 1 Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No No A No A No 385H 0 No No A No No No 386H 0 to 120 115% No No A No A A 387H 0.0 to 2.0 0.0 s* No No A No A A 388H 0 to 50 10% No No A No A A 389H 0.0 to 10.0 0.5 s No No A No A A 38AH 0 No No A No No No 38BH 0 No No A No No No 38CH 2.0 s No No A No A No 38DH PG division rate Sets the division ratio for the PG (PG pulse mon- speed control board pulse output. itor) Division ratio = (1+ n) /m (n=0 or 1 m=1 to 32) F1-06 F1-06 PG Output Ratio Integral value during accel/ decel enable/ disable F1-07 PG Ramp PI/I Sel F1-08 F1-09 Overspeed detection level PG Overspd Level Overspeed detection delay time PG Overspd Time F1-10 F1-11 F1-12 F1-13 F1-14 n m This constant is only effective when a PG-B2 is used. The possible division ratio settings are: 1/32 ≤ F1-06 ≤ 1. Sets integral control during acceleration/deceleration to either enabled or disabled. 0: Disabled (The integral function isn't used while accelerating or decelerating; it is used at constant speeds.) 1: Enabled (The integral function is used at all times.) Sets the overspeed detection method. Frequencies above that set for F108 (set as a percentage of the maximum output frequency) that continue to exceed this frequency for the time set in F1-09 are detected as overspeed faults. Excessive speed deviation Sets the speed deviation detection detection level method. Any speed deviation above the PG Deviate F1-10 set level (set as a percentLevel age of the maximum output frequency) that continues for the Excessive speed deviation time set in F1-11 is detected as a detection delay speed deviation. Speed deviation is the difference time between actual motor speed and PG Deviate the reference command speed. Time Number of PG gear teeth 1 PG # Gear Teeth1 Number of PG gear teeth 2 PG # Gear Teeth2 PG open-circuit detection time PGO Detect Time Sets the number of teeth on the gears if there are gears between the PG and the motor. Input pulses from PG 60 F1-13 F1-01 F1-12 0 to 1000 A gear ratio of 1 will be used if either of these constants is set to 0. Used to set the PG disconnection detection time. PGO will be detected if the detection time continues beyond the set time. 0.0 to 10.0 * When the control method is changed, the factory setting will change. The flux vector factory setting is given. 6-159 Using PG Speed Control Board There are four types of PG Speed Control Board that can be used in V/f control with PG. • PG-A2: A-phase (single) pulse input, compatible with open collector or complimentary outputs. • PG-B2: A/B-phase pulse input, compatible with complimentary outputs. • PG-D2: A-phase (single) pulse input, compatible with line drivers. • PG-X2: A/B/Z-phase pulse input, compatible with line drivers. There are two types of PG Speed Control Boards that can be used for flux vector control. • PG-B2: A/B phase pulse inputs, complementary outputs • PG-X2: A/B/Z phase pulse inputs, line driver outputs For the connection diagram, refer to page 2-35 to 2-37. Setting Number of PG Pulses Set the number of PG (Pulse Generator/Encoder) pulses in pulses/rotation. Set the number of A-phase or Bphase pulses per 1 motor rotation in F1-01. Matching PG Rotation Direction and Motor Rotation Direction Constant F1-05 matches the PG rotation direction and the motor rotation direction. If the motor is rotating forwards, set whether it is A-phase driven or B-phase driven. Make this setting when using PG-B2 or PG-X2. Inverter Motor PG (encoder) Forward Command Pulse output A-phase driven when set value = 0 B-phase driven when set value = 1 A-phase A-phase B-phase B-phase Example: Forward rotation of standard Yaskawa motor (PG used: Samtack (KK)) Forward Command Motor output axis rotates counter-clockwise during Inverter Forward Command. Rotation (CCW) A-phase B-phase Yaskawa standard PG used is A-phase driven (CCW) when motor rotation is forward. Fig 6.82 PG Rotation Direction Setting Generally, PG is A-phase driven when rotation is clockwise (CW) see from the input axis. Also, motor rotation is counter-clockwise (CCW) seen from the output side when Forward Commands are output. Consequently, when motor rotation is forward, PG is normally A-phase driven when a load is applied, and B-phase driven when a load is not applied. 6-160 Options Setting Number of Gear Teeth Between PG and Motor Set the number of PG gear teeth in F1-12 and F1-13. If there are gears between the motor and PG, you can operate the motor by setting the number of gear teeth. When the number of gear teeth has been set, the speed of motor rotations within the Inverter is calculated using the following formula. Speed of motor rotations (min−1.) = No. of input pulses from PG × 60 / F1-01 × F1-13 (No. of gear teeth on load side) / F1-12 (No. of gear teeth on motor side) Matching Motor Speed During Acceleration and Deceleration to Frequency Reference You can select whether to enable or disable integral operation during acceleration and deceleration when using V/F with PG control. To match the motor speed as closely as possible to the frequency reference even during acceleration and deceleration, set F1-07 to 1. If F1-01 is set to 1, overshoot or undershoot may occur easily immediately after acceleration and deceleration. To minimize the possibility of overshoot or undershoot occurring, set F1-01 to 0. IMPORTANT Setting PG Pulse Monitor Output Dividing Ratio This function is enabled only when using PG speed control board PG-B2. Set the dividing ratio for the PG pulse monitor output. The set value is expressed as n for the higher place digit, and m for the lower place 2 digits. The dividing ratio is calculated as follows: Dividing ratio = (1 + n)/m (Setting range) n: 0 or 1, m: 1 to 32 F1-06 = n m The dividing ratio can be set within the following range: 1/32 ≤ F1-06 ≤ 1. For example, if the dividing ratio is 1/2 (set value 2), half of the number of pulses from the PG are monitor outputs. Detecting PG Open Circuit Select the stopping method when PG cable disconnected is detected and the PG open circuit (PGO) detection time. When the Inverter is operating with the frequency reference set to 1% minimum (except when operating on direct current), if the speed feedback from PG is greater than the time setting in F1-14, PGO is detected. Detecting Motor Overspeed An error is detected when the number of motor rotations exceeds the regulated limit. An overspeed (OS) is detected when a frequency that exceeds the set value in F1-08 continues for longer than the time set in F1-09. After detecting an overspeed (OS), the Inverter stops according to the setting in F1-03. Detecting Speed Difference between the Motor and Speed Reference An error is detected when the speed deviation (i.e., the difference between the designated speed and the actual motor speed) is too great. Speed deviation (DEV) is detected after a speed agreement is detected and when the speed reference and actual workpiece speed are within the setting of L4-02, if a speed deviation great than the set value in F1-10 continues for longer than the time set in F1-11. After a speed deviation is detected, the Inverter stops according to the setting in F1-04. 6-161 Using Digital Output Boards There are two types of Inverter digital output boards: • DO-02C Relay contact output (DPDT contact) • DO-08 6 photocoupler output channels (shared commons) 2 (independent) relay contact output channels (NC contact) +24 V TD Inverter control panel 3CN NC NO 1 2 CH1 3 3CN Inverter control panel 3CN Photocoupler TD5 CH1 TD6 CH2 TD7 3CN 4 NC NO 5 6 Relay contact DO-02C Digital Output Card CH3 TD8 CH4 TD9 CH5 TD10 TD11 TD1 TD2 TD3 TD4 CH2 Photocoupler CH6 COM (0 V common) CH7 CH8 Relay contact DO-08 Digital Output Card Fig 6.83 Digital Output Boards Related Constants Name Constant Number Display Channel 1 output selection F5-01 DO Ch1 Select Channel 2 output selection F5-02 DO Ch2 Select F5-03 Channel 3 output selection DO Ch3 Select F5-04 Channel 4 output selection DO Ch4 Select F5-05 Channel 5 output selection DO Ch5 Select F5-06 Channel 6 output selection DO Ch6 Select 6-162 Description Setting Range Factory Setting Change during Operation Effective when a Digital Output Board (DO-02C or DO-08) is used. Set the number of the multi-function output to be output. 0 to 37 0 Effective when a Digital Output Board (DO-02C or DO-08) is used. Set the number of the multi-function output to be output. 0 to 37 Effective when a DO-08 Digital Output Board is used. Set the number of the multi-function output to be output. Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 399H 1 No A A A A A 39AH 0 to 37 2 No A A A A A 39BH Effective when a DO-08 Digital Output Board is used. Set the number of the multi-function output to be output. 0 to 37 4 No A A A A A 39CH Effective when a DO-08 Digital Output Board is used. Set the number of the multi-function output to be output. 0 to 37 6 No A A A A A 39DH Effective when a DO-08 Digital Output Board is used. Set the number of the multi-function output to be output. 0 to 37 37 No A A A A A 39EH Options Name Constant Number Change during Operation 0 to 37 0F Effective when a DO-08 Digital Output Board is used. Set the number of the multi-function output to be output. 0 to 37 Effective when a DO-08 Digital Output Board is used. Set the output mode. 0: 8-channel individual outputs 1: Binary code output 2: Output according to F5-01 to F5-08 settings. 0 to 2 Display F5-07 DO Ch7 Select Channel 8 output selection DO Ch8 Select DO-08 output mode selection F5-09 Factory Setting Description Channel 7 output selection F5-08 Setting Range DO-08 Selection Effective when a DO-08 Digital Output Board is used. Set the number of the multi-function output to be output. Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 No A A A A A 39FH 0F No A A A A A 3A0H 0 No A A A A A 3A1H Setting Output Items for the DO-02C Digital Output Board If using DO-02C Digital Output Board, set the output items using F5-01 and F5-02. Setting Output Items for the DO-08 Digital Output Board If using DO-08 Digital Output Board, select one of the following three output modes according to the setting in F5-09. F5-09 Set to 0 Set Value 0: 8 separate outputs Terminal Number Output Details TD5-TD11 Overcurrent (SC, OC, GF) TD6-TD11 Overvoltage (OV) TD7-TD11 Inverter overload (OL2) TD8-TD11 Fuse blown (PUF) TD9-TD11 Overspeed (OS) TD10-TD11 Inverter overheated (OH1) or motor overload (OL1) TD1-TD2 Zero-speed detected TD3-TD4 Speed agreement 6-163 F5-09 Set to 1 Set Value 1: Binary code output Terminal Number Output Details TD5-TD11 bit 0 TD6-TD11 bit 1 TD7-TD11 bit 2 TD8-TD11 bit 3 TD9-TD11 Zero-speed detected TD10-TD11 Speed agreement TD1-TD2 Operating TD3-TD4 Minor fault Encoded output (Refer to table below) The following table shows the code outputs. Bits 3, 2, 1, and 0 Output Details Bits 3, 2, 1, and 0 Output Details 0000 No error 1000 External fault (EFxx) 0001 Overcurrent (SC, OC, GF) 1001 Controller error (CPFxx) 0010 Overvoltage (OV) 1010 Motor overload (OL1) 0011 Inverter overload (OL2) 1011 Not used 0100 Inverter overheated (OH, OH1) 1100 Power loss (UV1, UV2, or UV3) 0101 Overspeed (OS) 1101 Speed deviation (DEV) 0110 Fuse blown (PUF) 1110 PG open circuit (PGO) 0111 Dynamic braking resistor (RH) Injection brake transistor error (RR) 1111 Not used F5-09 Set to 2 Output depends on the settings in F5-01 to F5-08. Using an Analog Reference Board AI-14B provides 3 channels of bi-polar inputs with 14-bit A/D conversion accuracy (and a sign bit). The function of each channel is determined by the setting of F2-01. AI-14U provides 2 channels of bi-polar inputs with 14-bit A/D conversion accuracy. Channel 1 is a voltage input and channel 2 is a current input. The sum of channels 1 and 2 is a frequency input. F2-01 does not need to be set for the AI-14U. 6-164 Options Related Constants Name Constant Number F2-01 Description Display Setting Range Bi-polar or uni- Sets the functions for channel 1 to polar input 3 that are effective when the AIselection 14B Analog Reference Board is used. 0: 3-channel individual (Channel 1: terminal A1, Channel 2: terminal A2, Channel 3: terminal A3) 0 or 1 1: 3-channel addition (Addition AI-14 Input Sel values are the frequency reference) When set to 0, select 1 for b1-01. In this case the multi-function input “Option/Inverter selection” cannot be used. Factory Setting Change during Operation 0 No Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A MEMO BUS Register 38FH Setting Precautions Always set b1-01 (Reference selection) to 1 (control circuit terminal) when using the AI-14B for three channels of independent inputs. When this is done, H1-01 to H1-10 (multi-function contact inputs) cannot be set to 2 (Option/Inverter selection). Using a Digital Reference Board When using a DI-08 or DI-16H2 Digital Reference Board, set b1-01 (Reference selection) to 3 (Option board). The DI-16H2 can be used to set a frequency using a 16-bit digital reference. The DI-08 can be used to set a frequency using a 8-bit digital reference. Related Constants Name Constant Number Display Digital input option F3-01 DI Input Description Setting Range Factory Setting Change during Operation Sets the Digital Reference Board input method. 0: BCD 1% unit 1: BCD 0.1% unit 2: BCD 0.01% unit 3: BCD 1 Hz unit 4: BCD 0.1 Hz unit 5: BCD 0.01 Hz unit 6: BCD special setting (5-digit input) 7: Binary input 6 is only effective when the DI16H2 is used. When o1-03 is set to 2 or higher, the input will be BCD, and the units will change to the o1-03 setting. 0 to 7 0 No Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A MEMO BUS Register 390H 6-165 Name Constant Number Display Description Setting Range Factory Setting Change during Operation 0 to 39999 0 No Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A MEMO BUS Register Frequency units Sets the units that will be set and of reference set- displayed for the frequency referting and moni- ence and frequency monitor. tor 0: 0.01 Hz units 1: 0.01% units (Maximum output frequency is 100%) 2 to 39: o1-03 Display Scaling min−1 units (Sets the motor poles.) 40 to 39999: User desired display Set the desired values for setting and display for the max. output frequency. 502H Set 4-digit number excluding the decimal point. Set the number of digits below the decimal point to display. Example: When the max. output frequency value is 200.0, set 12000 Selecting Input Terminal Functions for the DI-16H2 Digital Reference Board The frequency reference from the DI-16H2 Board is determined by the setting of F3-01 and the 12/16-bit switch on the option board. The possible settings are listed in the following table. 6-166 Options Terminal TC1 TC2 Pin No. 12-bit Binary 16-bit Binary with Sign with Sign F3-01 = 7 F3-01 = 7 S1: 12 bit S1: 16 bit 3-digit BCD with Sign F3-01 = 0 to 5 S1: 12 bit 4-digit BCD with 5-digit BCD withSign out Sign F3-01 = 0 to 5 F3-01 = 6 S1: 16 bit S1: 16 bit 1 1 Bit 1 (20) Bit 1 (20) 1 2 Bit 1 (21) Bit 1 (21) 2 3 Bit 1 (22) Bit 1 (22) 4 4 Bit 1 (23) Bit 1 (23) 8 8 1 5 Bit 1 (24) Bit 1 (24) 1 1 2 5 5 BCD digit 1 (0 to 9) 2 4 BCD digit 1 (0 to 9) 4 Bit 1 (2 ) Bit 1 (2 ) 2 7 Bit 1 (26) Bit 1 (26) 4 8 Bit 1 (27) Bit 1 (27) 8 8 1 9 Bit 1 (28) Bit 1 (28) 1 1 2 2 4 9 9 10 Bit 1 (2 ) Bit 1 (2 ) 2 1 Bit 1 (210) (210) 4 2 Bit 1 (211) Bit 1 (211) 8 3 - Bit 1 (212) 4 Bit 1 BCD digit 3 (0 to 9) 4 4 BCD digit 2 (0 to 9) BCD digit 3 (0 to 9) 4 - 1 2 - 13) Bit 1 (2 - 2 5 - Bit 1 (214) - 4 6 - Bit 1 (215) - 8 Sign signal (0: Forward, 1: Reverse) 8 SET (read) signal (1: Read) 9 Input signal common (0 V) TC3 BCD digit 3 (0 to 9) 8 1 7 BCD digit 2 (0 to 9) 8 8 BCD digit 4 (0 to 9) BCD digit 1 (0, 2, 4, 6, 8) 8 6 BCD digit 2 (0 to 9) 2 2 4 BCD digit 4 (0 to 9) 8 1 2 BCD digit 5 (0 to 3) Shield wire connection terminal Application Precautions • The maximum frequency (100% speed) reference will be used when the binary input is set (setting: 6 or 7) and all bits are 1. • Setting F3-01 to 6 is valid only when the D1-16H2 is used. Using this setting, a frequency from 0.00 to 399.8 Hz can be set in BCD. The sign bit is used as a data bit, so only positive (plus) data can be set. Also, the digit starts from 0, so the minimum setting is 0.02 Hz. Selecting the Input Terminal Function for a DI-08 Digital Reference Board The frequency reference from a DI-08 Board is determined by the setting of F3-01, as shown in the following table. 6-167 Terminal TC Pin No. 8-bit Binary with Sign F3-01 = 7 2-digit BCD with Sign F3-01 = 0 to 5 1 Bit 1 (20) 1 2 Bit 1 (21) 2 2 3 Bit 1 (2 ) 4 4 Bit 1 (23) 8 5 Bit 1 (24) 1 6 Bit 1 (25) 2 6 7 Bit 1 (2 ) 4 8 Bit 1 (27) 8 9 Sign signal 10 SET (read) signal 11 Reference common signal (0 V) BCD digit 1 (0 to 9) BCD digit 2 (0 to 15) Application Precautions The DI-08 will not function if F3-01 is set to 6 Selecting the Digital Reference The range of the digital references is determined by the combination of the settings of o1-03 and F3-01. The information monitored in U1-01 (Frequency reference) will also change. DI-16H2 Reference Ranges When using the DI-16H2, the following ranges can be set depending on the settings of the constants. o1-03 F3-01 0 1 2 0 or 1 3 4 5 6 7 6-168 Switch S1 Reference Input Mode Reference Setting Range 12 bits 3-digit BCD with sign, 1% -110 to 110% 16 bits 4-digit BCD with sign, 1% -110 to 110% 12 bits 3-digit BCD with sign, 0.1% -110.0 to 110.0% 16 bits 4-digit BCD with sign, 0.1% -110.0 to 110.0% 12 bits 3-digit BCD with sign, 0.01% -15.99 to 15.99% 16 bits 4-digit BCD with sign, 0.01% -110.0 to 110.0% 12 bits 3-digit BCD with sign, 1 Hz -400 to 400 Hz 16 bits 4-digit BCD with sign, 1 Hz -400 to 400 Hz 12 bits 3-digit BCD with sign, 0.1 Hz -159.9 to 159.9 Hz 16 bits 4-digit BCD with sign, 0.1 Hz -400.0 to 400.0 Hz 12 bits 3-digit BCD with sign, 0.01 Hz -15.99 to 15.99 Hz 16 bits 4-digit BCD with sign, 0.01 Hz -159.99 to 159.99 Hz 16 bits 5-digit BCD without sign, 0.01 Hz 000.00 to 399.98 Hz 12 bits 12-bit binary with sign, 100%/4095 -4095 to 4095 16 bits 16-bit binary with sign, 100%/30000 -33000 to 33000 U1-01 Monitor Unit o1-03 = 0 o1-03 = 1 0.01 Hz 0.01% Options o1-03 F3-01 2 to 39 X0040 to X9999 (X = 0 to 3) X1000 (X = 0 to 3) Switch S1 Reference Input Mode Reference Setting Range U1-01 Monitor Unit o1-03 = 0 o1-03 = 1 12 bits 3-digit BCD with sign, 1 rpm -1599 to 1599 rpm 1 rpm 16 bits 4-digit BCD with sign, 1 rpm -15999 to 15999 rpm 1 rpm - 12 bits 3-digit BCD with sign, 100%/(1- to 4digit setting of o1-03) -1599 to 1599 - 16 bits 4-digit BCD with sign, 100%/(1- to 4digit setting of o1-03) -9999 to 9999 (when o1-03 = 9999) - 16 bits 4-digit BCD with sign, 100%/10000 -1000 to 1000 - 5th digit of o1-03 setting: X = 0, unit: 1 X = 1, unit: 0.1 X = 2, unit: 0.01 X = 3, unit: 0.001 DI-08 Reference Ranges When using the DI-08, the following ranges can be set depending on the settings of the constants. F3-01 Reference Input Mode Reference Setting Range 0 2-digit BCD with sign, 1% -110 to 110% 1 2-digit BCD with sign, 0.1% -15.9 to 15.9% 2 2-digit BCD with sign, 0.01% -1.59 to 1.59% 3 2-digit BCD with sign, 1 Hz -159 to 159 Hz 4 2-digit BCD with sign, 0.1 Hz -15.9 to 15.9 Hz 5 2-digit BCD with sign, 0.01 Hz -1.59 to 1.59 Hz 6 7 U1-01 Monitor Unit o1-03 = 0 o1-03 = 1 0.01 Hz 0.01% 8-bit binary with sign, 100%/255 -255 to 255 6-169 Using Inverters for Elevating Machines This section describes precautions to be observed when using the Varispeed G7 for elevating machines such as elevators and cranes. IMPORTANT When performing trial operation, enable Current alarm function (L8-41 =1), and be sure to make adjustments to the braking sequence by using Peak hold functions (refer to Current Alarm Function and Peak Hold Current Monitoring Function in Chapter 6 ) so that the startup current is less than 150% of the Inverter rated current. Brake ON/OFF Sequence Brake ON/OFF Sequence For the holding brake’s ON/OFF sequence, use the following Inverter output signals according to the set control method. Brake ON/OFF Signal Signal Name Constant *1 Control Method V/f (A1-02 = 0) V/f with PG (A1-02 = 1) Open-loop vector 1 (A1-02 = 2, factory setting) Frequency detection 2 H2-01 = 05*5 Frequency detection 5*4 H2-01 = 36*5 Flux vector (A1-02 = 3) During run 2 H2-01 = 37 Brake ON/OFF Level Adjustment Signal Name Constant • Speed agree detection level • Speed agree detection width • L4-01 = 1.0 to 3.0 Hz *2 • L4-02 = 0.1 to 0.5 Hz *3 Zero-speed level (OFF timing only) b2-01 = 0.1 to 0.5 Hz Do not set Open-loop vector 2 for use in elevating machines. IMPORTANT * 1. This example shows multi-function output terminals M1-M2 used for the holding brake ON/OFF signal. Do not set H2-01 to 0 (During run). * 2. This is the standard setting range for open-loop vector 1 control. For V/f control, set to approximately the motor rated slip frequency +0.5 Hz. If the set value is too low, the motor torque is insufficient and the load may slip when the brake is applied. Be sure to set L4-01 to a value larger than that of E1-09 (Min. output frequency) and larger than that of L4-02 shown in Figure 6.84. If the set value is too large, the motor may not run smoothly when it starts running. * 3. The hysteresis in frequency detection 2 can be adjusted (from 0.1 to 0.5 Hz) by L4-02 (speed agree detection width). Change the setting to approximately 0.1 Hz if there are drops while stopping. * 4. Applicable for G7-Series Inverters with software versions PRG:1038 or later. * 5. When using frequency detection 2, set L4-01 before H2-01. If H2-01 is set before L4-01, the holding brake will engage while stopping. For Inverters with software versions PRG: 1038 or later, use frequency detection 5 in which a holding brake signal is OFF when the Inverter is baseblocked. L4-01 L4-02 Output frequency Frequency detection 2 Time ON Fig 6.84 6-170 OFF Using Inverters for Elevating Machines Sequence Circuit Configuration The brake ON/OFF sequence circuit configuration is shown below. Holding brake auxiliary relay coil Inverter (Varispeed G7) Fault contacts MA UP DOWN S1 (Forward run) MB S2 (Reverse run) MC Safety circuit UP DOWN BR BR HIGH/LOW S6 (Multi-step speed reference 2) M1 SC M2 Energizes the brake when ON (250 VAC 1 A or less, 30 VDC 1 A or less) Frequency detection 2, 5 or During run 2 Note Design the sequence so that the holding brake contact is open when the sequence operation conditions are satisfied and the contact between M1 and M2 is closed (ON). Make sure that the holding brake contact is closed when the emergency stop signal or Inverter fault contact output signal is ON. Fig 6.85 Brake ON/OFF Sequence Circuit Configuration Time Chart Output Input The brake ON/OFF sequence time charts are shown in Figs. 6.86 and 6.87. S1-SC UP S6-SC High speed/ Low speed OFF ON OFF ON d1-03 Output frequency 0 b4-01 L4-01 Frequency detection 2 M1-M2 (H2-01 = 05) Holding brake operation d1-01 (Enabled when b1-01 = 0) DC injection braking Time OFF ON CLOSE OPEN CLOSE Note For variable speed operation by an analog signal, set to b1-01 = 1. Output Input Fig 6.86 Brake ON/OFF Sequence Time Chart (V/f, V/f with PG, open-loop vector 1) S1-SC UP S6-SC High speed/ Low speed OFF ON OFF ON d1-03 Output frequency 0 M1-M2 During run 2 (H2-01 = 37) Holding brake operation CLOSE d1-01 (Enabled when b1-01 = 0) b2-01 Time DC injection braking (Zero-speed control) ON OPEN OFF CLOSE Note For variable speed operation by an analog signal, set to b1-01 = 1. Fig 6.87 Brake ON/OFF Sequence Time Chart (Flux Vector) 6-171 Stall Prevention during Deceleration If connecting a braking resistor to discharge regenerative energy, be sure to set Stall prevention selection during decel (L3-04) to 0 (Disabled). IMPORTANT If Stall prevention selection during decel (L3-04) is set to the initial value 1 (Enabled), the motor may not stop within the specified decelerating time. Stall prevention selection during accel (L3-01) and Stall prevention selection during running (L3-05) should be set to their initial values 1 (Enabled) to enable these functions. Autotuning Always perform autotuning with the motor before operating using vector control. Be sure to disconnect the motor from the load before conducting autotuning. Conducting autotuning while the motor is connected to an elevating machine system is dangerous because it automatically runs the motor for approximately one minute. IMPORTANT 1. When the motor cannot be disconnected from the load, perform stationary autotuning (T1-01 = 1 or 4). For G7-Series Inverters with software versions PRG: 1039 or later, perform stationary autotuning 2 (T1-01 = 4). Stationary autotuning will apply current to the motor in its stopped condition and automatically measure the motor data. In the initial running period after autotuning (T1-01 =1) (20% speed min., fixed speed for 1 s min.), the motor data measured by autotuning will automatically be corrected. 2. To improve low-speed torque characteristics using V/f control, conduct stationary autotuning for line to line resistance only (T1-01 = 2). 3. When conducting autotuning on wound motor or other special types of motors, obtain a test report for the motor in advance and confirm that the E2 motor constants after autotuning do not vary greatly from those of the test report. Braking Resistor Overheating Protection When using a braking resistor other than the Braking Resistor Unit, provide a sequence with a thermal overload relay or similar means to turn off the power input to the Inverter when it detects resistor overheating. See the Connection Diagram on page 2-3 for this sequence circuit. Momentary Power Loss Restart Do not use the momentary power loss restart and fault restart functions in applications for elevating machines. Make sure that L2-01=0 and L5-01=0. If these functions are used, the motor coasts to a stop with the brake contact open when a momentary power loss or fault occurs during operation, possibly resulting in serious accidents. Torque Limit The torque limit values (L7-01 to L7-04) are the motor's rated torque. When there is a possibility of insufficient torque at start-up or other time, increase the Inverter capacity and set the torque limit value to between 200% and 300% (factory setting is 200%). 6-172 Using Inverters for Elevating Machines I/O Open-phase Protection and Overtorque Detection To prevent the machine from falling when the motor is open-phase or a similar situation, enable L8-05 and L807 (Input and output open-phase protection selection) and L6-01 to L6-06 (Overtorque detection) (factory setting is Disabled). Falling detection or a similar safety measure should also be provided on the machine side. External Baseblock Signal If the external baseblock command (settings 8 and 9 of H1-01 to H1-10) is input while the motor is running, the motor will immediately coast to a stop. Do not input the external baseblock command while the motor is running unless necessary. Make sure that the holding brake operates when using the external base block command for an emergency stop or interlock to start the Inverter. If the external baseblock command is input and immediately reset, the Inverter does not output voltage during the value of L2-03 (Min. baseblock time), which factory setting is 0.5 to 2.0 seconds depending on the Inverter capacity. Do not use the external baseblock command in an application where the motor is frequently started and stopped. Acceleration/Deceleration Time If the delay time for the holding brake’s mechanical operation is not taken into consideration and the acceleration/deceleration time on the Inverter side is set to a time that is too short, and overcurrent or wear on the brakes may occur at staring or the load will slip at stopping because the holding brake does not operate on time. If so, use the dwell function at start described on page 6-176 or the dwell function at stop described on page 6-177 to tune the timing for the holding brake. Magnetic Contactor on the Inverter’s Output-side Do not install a magnetic contactor between the Inverter and the motor. If a magnetic contactor must be installed because of local electrical codes or regulations or to operate motors with an Inverter, excluding emergencies, open or close the magnetic contactor only when the holding brake is fully closed and the Inverter is in baseblock status with the baseblock signal ON. If the magnetic contactor is opened or closed while the Inverter is controlling the motor or DC injection braking (Zero-speed control), surge voltage or a current from the motor by full-voltage starting may cause an Inverter fault. When a magnetic contactor is installed between the Inverter and the motor, set L8-07 (Output open-phase protection selection) to 1 or 2 (Enabled). 6-173 Control-related Adjustments The Varispeed G7 is designed to provide sufficient performance for elevating machines. However, if problems related to controllability should occur, such as vibration or slipping, adjust the following constants in accordance with the control method. Only constants that frequently require adjustment are listed in this table. Table 6.4 Control-related Adjustments Control Method Constant Number Name • Increasing torque and speed response • Controlling hunting 1.00 and vibration in middle-range speeds (10 to 40 Hz) Recommended Setting Adjustment Method • Torque or speed response is insufficient: Reduce the setting • Hunting or vibration occurs: Increase the setting N2-01 Speed feedback detection control (AFR) gain C4-02 Torque com• Increasing torque and pensation speed response primary 20 ms • Controlling hunting delay time and vibration constant • Torque or speed response is insufficient: Reduce the setting 20 to 100 ms • Hunting or vibration occurs: Increase the setting C3-02 Slip compen- • Increasing speed sation priresponse mary delay • Improving speed statime bility 100 to 500 ms • Speed response is slow: Reduce the setting • Speed is not stable: Increase the setting 0.5 to 1.5 • Speed is slow: Increase the setting • Speed is too fast: Reduce the setting 1 to F • Motor magnetic noise is high: Increase the setting • Hunting or vibration occurs at low speeds: Reduce the setting Open-loop vector 1 control (A1-02 = 2) C3-01 C6-02 E1-08 E1-10 Slip compen- • Improving speed sation gain accuracy Carrier frequency selection 200 ms 1.0 • Reducing motor magnetic noise • Controlling hunting *1 and vibration at low speeds (10 Hz or lower) Mid. output *2 frequency • Improving torque and 11.0 V voltage (VC) speed response at low speeds Min. output • Controlling shock at frequency 2.0 V*2 startup voltage (VMIN) 6-174 Factory Setting Performance 0.50 to 2.00 12.0 to 13.0 V*2 2.0 to 3.0 V*2 • Torque or speed response is insufficient: Increase the setting • Shock at startup is large: Reduce the setting Using Inverters for Elevating Machines Table 6.4 Control-related Adjustments (Continued) Control Method Constant Number Name Factory Setting Performance ASR proportional (P) • Increasing torque and gain 1 speed response 20.00 • Controlling hunting ASR proporand vibration tional (P) Recommended Setting 10.00 to 50.00 • Torque or speed response is insufficient: Increase the setting • Hunting or vibration occurs: Reduce the setting 0.300 to 1.000 s • Torque or speed response is insufficient: Reduce the setting • Hunting or vibration occurs: Increase the setting C5-07 Switching the ASR proASR switchportional gain and inte- 0.0 Hz (no ing fregral time according to switching) quency the output frequency. 0.0 to max. output frequency Set the output frequency at which to change the ASR proportional gain and integral time when the same values cannot be used for both high-speed and low-speed operation. C5-06 ASR primary delay time 0.004 to 0.020 Machine rigidity is low and the system vibrates easily: Increase the setting N1-02 • Controlling hunting Hunting-preand vibration in midvention gain dle-range speeds (10 to 40 Hz) 0.50 to 2.00 • Torque is insufficient for heavy loads: Reduce the setting • Hunting or vibration occurs for light loads: Increase the setting 1 to F • Motor magnetic noise is high: Increase the setting • Hunting or vibration occurs at low to middlerange speeds: Reduce the setting 0.50 to 1.50 • Torque is insufficient at low speeds: Increase the setting • Hunting or vibration occurs for light loads: Reduce the setting C5-01 C5-03 gain 2 C5-02 Flux vector control (A1-02 = 3) Adjustment Method C5-04 ASR integral (I) time 1 ASR integral (I) time 2 • Increasing torque and speed response 0.500 s • Controlling hunting and vibration • Controlling hunting and vibration 0.004 s 1.00 • Reducing motor magnetic noise *1 • Controlling hunting and vibration at low and medium speeds C6-02 Carrier frequency selection C4-01 • Improving torque at low speeds (10 Hz or Torque comlower) pensation 1.00 • Controlling hunting gain and vibration for light loads V/f control (A1-02 = 0 or 1) E1-08 E1-10 Mid. output frequency voltage (VC) • Improving torque at low speeds Min. output • Controlling shock at frequency startup voltage (VMIN) 15.0 V*2 13.0 to 16.0 V*2 9.0 V*2 7.0 to 10.0 V*2 • Torque is insufficient at low speeds: Increase the setting • Shock at startup is large: Reduce the setting * 1. Varies depending on capacity. * 2. The setting is given for 200 V Class Inverters. Double the voltage for 400 V Class Inverters. Note 1. Do not change C4-01 (Torque compensation gain) from its factory setting of 1.00 when using open-loop vector 1 control. 2. If speeds are inaccurate during regeneration in open-loop vector 1 control, enable Slip compensation selection during regeneration (C3-04 = 1). If speeds are inaccurate in the high-speed range, enable Output voltage limit operation selection (C3-05 = 1). 6-175 3. Do not use Slip compensation gain (C3-01) during V/f control (A1-02 = 0). (It is not used with the factory setting.) 4. Use the ASR constants (C5-01 to C5-05) in their factory settings when using V/f control with PG (A1-02 = 1). Vibration may occur if these constants are changed greatly from their factory settings. 5. The torque and speed response of high-resistance (high-slip) motors are insufficient. Use appropriate adjustments to improve them. On the contrary, low-resistance (low-slip) motors are easily subject to hunting and vibration. Here too, use appropriate adjustments to improve them. 6. The current during startup may increase when C4-02 (Torque compensation primary delay time constant) is increased. Check the current during startup while adjusting this constant. Reducing Shock during Elevating Machine Start, Stop, Acceleration, and Deceleration When the riding comfort during start, stop, acceleration, and deceleration is of high importance, as it is for elevators in which people ride, adjust the following constants. S-curve Characteristics, Acceleration/Deceleration Times (High speed) C2-02 C2-03 Output frequency (Low speed) C2-03 C2-01 C2-04 C2-04 Acceleration time IMPORTANT Deceleration time DC injection braking when stopping (Zero-speed control for flux vector control) 1. The factory setting for C2-04 (S-curve characteristic time at deceleration end) is 0.00 second, while the factory setting for all other S-curve characteristic times is 0.20 second. Make appropriate settings for the accel/decel times and S-curve characteristic times at each point. (S-curve characteristic time = Approximately 0.2 to 1.0 second) 2. The accel/decel rate can be automatically switched during acceleration and deceleration by using C1-11 (Accel/decel time switching frequency). (Factory setting: Disabled) Output frequency ≥ set frequency: C1-01, C1-02 accel/decel times Output frequency < set frequency: C1-07, C1-08 accel/decel times 3. If the output frequency during the S-curve characteristic time for deceleration falls below the value set for E1-09 (Min. output frequency), the S-curve characteristic will be cancelled, and the DC injection braking (Zero-speed control) will be applied. 4. Do not use the S-curve characteristic for applications where a short run time is desired, such as in cranes and hoists. (S-curve characteristic time = Approximately 0.0 to 0.2 second) Dwell Function at Start b6-02 (Dwell time at start) 0.1 to 0.3 sec Output frequency (High speed) b6-01 (Dwell frequency at start) 0.1 to 3.0 Hz Frequency detection 2 or During run 2 OFF Holding brake operation 6-176 CLOSE ON OPEN t Using Inverters for Elevating Machines If the mechanical operation of the holding brake is slow, use the dwell function at start to prevent brake wear, and accelerate after the brake is completely open. IMPORTANT 1. When using open-loop vector 1 control and V/f control, set b6-01 (Dwell frequency at start) higher than frequency detection 2 (frequency when brakes open). 2. If the motor tends to have insufficient torque when started, use the DC injection braking function to allow sufficient motor current (torque) before starting. • b2-03 (DC injection braking time at start): 0.2 to 0.5 s • b2-02 (DC injection braking current): 50% to 80% (open-loop vector 1 control, V/f control only) Stopping with DC Injection Braking and Zero-speed Control b2-04 (DC injection braking time at stop (zero-speed control time at stop): 0.3 to 0.5 s (HIGH) Output frequency (LOW) Frequency detection 2 or During run 2 t ON Holding brake operation OPEN OFF b2-01 [Zero speed level (DC injection braking starting frequency)]: 0.1 to 3.0 Hz b2-02 (DC injection braking current): 50% to 80% (open-loop vector control, V/f control only) CLOSE When the holding brake’s mechanical operation is slow, use DC injection braking (zero-speed control for flux vector control) until the brakes are fully closed to prevent the brakes from slipping when stopping. 1. When the load cannot be maintained sufficiently using DC injection braking with open-loop vector 1 control and V/f control, use the dwell functions at stop. • b6-03 (Dwell frequency at stop): Min. output frequency to 3.0 Hz. IMPORTANT The value must be less than the frequency when frequency detection 2 is OFF (L4-01 − L4-02). • b6-04 (Dwell time at stop): 0.3 to 0.5 s [b2-04 (DC injection braking at stop): 0.0 s] 2. If the Inverter and motor must be isolated while stopping using a magnetic contactor, for example in an elevator, fully close the holding brakes and isolate the Inverter during baseblock (during baseblock signal: ON) as stipulated by law in the EU. During motor control or DC injection braking (zero-speed control), an Inverter error may occur due to surge voltage. When a magnetic contactor is used between the Inverter and motor, set L8-07 (Output openphase protection) to 1 (enabled). Torque Compensation (Flux Vector Control Only) When flux vector control is used, the torque compensation signals corresponding to the load can be input from the multi-function analog input terminals in advance to reduce shock, such as that caused by opening and closing holding brakes. The load size and motoring/regenerating status must be detected at the machine side in advance. Check that polarity is correct. Incorrect polarity will increase the shock. 6-177 Sequence Circuit Configuration The following diagram shows the sequence circuit configuration for torque compensation. UP S1 (Forward run) DOWN S2 (Reverse run) HIGH/LOW S6 (Multi-step speed reference 2) SC (Using elevator control circuit) Torque compensation signal −10 to +10 V A3 H3-04 (multi-function analog input terminal A3 signal level) AC = 1 (−10 to +10 V) H3-05 (multi-function analog input terminal A3 function selection) = 14 (torque compensation) Use H3-06 and H3-07 for fine tuning. Fig 6.88 Torque Compensation Sequence Circuit Configuration Time Chart • Lifting The analog signals corresponding to the load size are input as torque compensation signals from before the Inverter starts until operation stops. (Factory setting: 10 V/100% torque) Positive polarity is input for motor loads and negative polarity is input for regenerative loads. The following diagram shows the time chart for lifting. UP (Forward) ON HIGH/LOW ON Torque compensation signal: 0 OFF OFF (Motor load: Inputs positive polarity.) (Regenerative load: Inputs negative polarity.) Analog signals corresponding to load size Same as above Output frequency Zero-speed control t 0 Motor torque (Motor load) (Regenerative load) 0 During run 2 ON Holding brake operation OPEN OFF CLOSE Fig 6.89 Torque Compensation Time Chart (Lifting) • Lowering In the same way as for lifting, when the torque decreases, the analog signals corresponding to the load size are input as torque compensation signals from before the Inverter starts until operation stops. (Factory setting: 10 V/100% torque) Negative polarity is input for motor loads and positive polarity is input for regenerative loads. The following diagram shows the time chart for lowering. 6-178 Using Inverters for Elevating Machines DOWN (Forward) ON HIGH/LOW ON Torque compensation signal: 0 OFF OFF (Regenerative load: Inputs positive polarity.) (Motor load: Inputs negative polarity.) Analog signals corresponding to load size Same as above 0 t Output frequency Motor torque (Regenerative load) (Motor load) 0 ON During run 2 Holding brake operation OPEN OFF CLOSE Fig 6.90 Torque Compensation Time Chart (Lowering) IMPORTANT 1. For either increasing or decreasing torque, externally maintain the torque compensation signals during operation to prevent them from fluctuating. Fluctuation in compensation signals during operation may result in vibration. 2. If reverse run is used for lifting and forward run is used for lowering, the torque compensation signal polarity must be reversed. Analog Input Filter Time Constant If noise enters the analog frequency reference during operation using analog frequency reference (b1-01 = 1), and operation becomes rough, implement noise countermeasures and also set H3-12 (Analog input filter time constant) to between 0.01 and 0.10 s. Confirming Startup Current and Reducing Carrier Frequency When performing a trial operation, set L8-41 (Current Alarm) to 1 (Enabled) and check the motor current using the peak hold current monitoring function (U1-83) of the Digital Operator or a clamp ammeter, with and without a mechanical load. An extremely high current will flow if the motor torque at start is insufficient, or if timing is not correct and the motor locks with the holding brake. If a current exceeding 150% of the Inverter rated current flows, the IGBT in the Inverter will be subject to heat stress, resulting in a shortened life span. In this case, take measures such as retuning and reduction of the load to reduce the current to a value less than 150% of the Inverter rated current. Unless low noise operation is required, reduce the Inverter carrier frequency to a value between 2 kHz and 2.5 kHz to reduce the influence of heat stress. 6-179 Overvoltage Inhibit Function Leave L3-11 (Overvoltage inhibit function selection) set to 0 (disabled). This function is used to prevent overvoltage tripping when the braking resistor is not used with a regenerative load. When this function is enabled, the torque reference on the regenerative side is automatically inhibited in the Inverter during regeneration. Using this function in elevating machines is dangerous because the elevator may slip and fall. Contact your Yaskawa representative for details on applications such as high-speed elevators (speed: 2 m/s or higher), direct-drive elevators, or Inverters designed for cranes. 6-180 Current Alarm Function Current Alarm Function This function displays a current alarm (HCA) on the Digital Operator and outputs a minor fault contact signal* when the Inverter output current exceeds 150% (effective value) of the rated output current. Use this function to check the current during trial operation for machines that increase Inverter output current, such as elevating machines. *To output a minor failure contact signal from a multi-function contact terminal, set H2- to 10 (Minor failure). If a current alarm occurs frequently, reduce the Inverter load. Use the peak hold current monitoring function (U1-83 and U1-84) when performing retuning to reduce the Inverter output current to 150% of the rated output current. Refer to Chapter 4 Trial Operation for details. For applications where a high current flows because of frequent start and stop operations, such as cranes, set L8-41 to 1 (Enabled). IMPORTANT If a current alarm occurs frequently, take measures such as: • Reducing the frequency of operation and loading. • Adjusting open/close timing of holding brake. • Increasing acceleration/deceleration time. • Taking enough time to produce motor magnetic flux (As described below). ■Related Constants Name Constant Number Display Current alarm L8-41 * HC Alarm Sel Description Setting Range Allows or restricts an alarm from being triggered when the relative output current rises above 150%. 0: Disabled. 1: Enabled (alarm will be output). 0 or 1 Change Factory during Setting Operation 0 No Control Methods V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A MEMO BUS Register 4F2H * Applicable for G7-Series Inverters with software versions PRG:1039 or later If load is applied to an induction motor at startup before motor magnetic flux has been produced (as when acceleration starts while the motor is locked by a brake mechanism or acceleration is too sudden), a high starting current may flow. In this case, use the following functions and constants to accelerate the motor after the magnetic flux is produced. Startup current can be reduced by producing motor magnetic flux. • Magnetic flux compensation function (See related constants b2-02 and b2-08) • Dwell function (See related constants b6-01 and b6-02) • Initial excitation function (See the setting 60 of the multi-function contact input H1) For flux loop vector control, a multi-function input terminal can be used for initial excitation by setting H1- to 60. • Field forcing function (See related constant d6-03) 6-181 Peak Hold Current Monitoring Function This function saves the peak value (effective value) of the Inverter output current and displays it on the Digital Operator for monitoring (U1-83). The Inverter output frequency at the moment the peak current value is saved can be also monitored (U1-84). At trial operation, perform adjustments so that the Inverter output current is limited to 150% of the rated current checking the constants U1-83 and U1-84 of this function. The values of peak current and output frequency during peak hold will be cleared when the Inverter stops and then starts, or when the power is turned OFF and then ON. They will be retained while being baseblocked (stopped). IMPORTANT ■Related Status Monitoring Constants Name Constant Number U1-83 *1 U1-84 *1 Display Peak hold current Current PeakHold Output frequency during peak hold Freq@ I PeakHold Control Methods Description Output Signal Level During Multi-Function Analog Output Displays the peak value of the current during run. “Peak Hold” refers to the moment that the peak value is saved. 10V: Inverter rated output current (-10 to 10V absolute value output) Displays the frequency value when the output current reached its peak value. 10V: Max frequency (-10V to 10V) Min. Unit 0.01 A Open MEMOBUS Loop Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector A A A A A 7CFH A A A A A 7D0H *2 0.01 Hz *3 * 1. Applicable for G7-Series Inverters with software versions PRG: 1039 or later. * 2. The minimum unit differs depending on the Inverter capacity. (0.01 A for Inverter of 0.4 kW to 7.5 kW, and 0.1 A for Inverter of 11 kW or more) * 3. The setting unit can be selected in o1-03. Related Fault Tracing Constants The peak hold values are saved in the fault trace memory when a fault occurs. Name Constant Number U2-21 *1 U2-22 *1 Display Peak hold current at fault Current PeakHold Peak hold output frequency at fault Freq@ I PeakHold Description Output Signal Level During Multi-Function Analog Output Displays the peak hold current when the last fault occurred. (Cannot be output.) Displays the frequency value at the moment the current reached its peak value when the last fault occurred. (Cannot be output.) Control Methods Min. Unit 0.01 A*2 0.01 Hz Open MEMOBUS Loop Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector A A A A A 7E6H A A A A A 7E7H * 1. Applicable for G7-Series Inverters with software versions PRG: 1039 or later. * 2. The minimum unit differs depending on the Inverter capacity. (0.01 A for Inverter of 0.4 kW to 7.5 kW, and 0.1 A for Inverter of 11 kW or more) 6-182 Maintenance Timer Display Function Maintenance Timer Display Function This function indicates that the estimated performance life of the cooling fan and electrolytic capacitor have been reached. The maintenance time periods displayed in the monitors as a percentage to the total life are only an estimate, not an exact prediction of actual performance life. IMPORTANT Use them as guidelines for replacement. Settings Required to Use Maintenance Timer Display Function Set H2- to 2F to use a multi-function contact output for this function and display an alarm on the Digital Operator (the constants U1-61 and U1-63). Multi-function Contact Outputs (H2-01 to H2-03) The maintenance time period for the cooling fan or electrolytic capacitor can be output from the multi-function contact terminal by setting H2- to 2F. Minor faults will not be output. Control Methods Setting Value Function 2F* Maintenance Time ON: The operation time of either the electrolytic capacitors or the cooling fan has reached the specified maintenance time. V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 Yes Yes Yes Yes Yes * Applicable for G7-Series Inverters with software versions PRG:1039 or later. Refer to Multi-function Contact Outputs: H2 in Chapter 5 User Constants for information on multi-function contact outputs. Related Status Monitoring Constants Name Constant Number U1-40 U1-61 * U1-63 * Description Setting Range Factory Setting Change during Operation Monitors the total operating time of the cooling fan. The time can be set in o2-10. (Cannot be output.) 1 hr Electrolytic For maintenance purposes, this capacitor main- timer shows the amount of time tenance the electrolytic capacitors have been operating. Capacitors should C Maintenance be replaced when the monitor Fan reaches 100%. (Cannot be output.) (Cannot be output.) Display Cooling fan operating time FAN Elapsed Time Cooling fan maintenance Maintenance This monitor displays the amount of time the cooling fan has been operating. Replace the cooling fan when the display reads 100%. Control Methods MEMO BUS Register V/f V/f with PG Open Loop Vector 1 Flux Vector Open Loop Vector 2 A A A A A A 67H 1% A A A A A A 7CH 1% A A A A A A 7EH * Applicable for G7-Series Inverters with software versions PRG: 1039 or later. 6-183 Related Alarm Displays When setting a multi-function contact output H2- to 2F, the alarm is displayed on the Digital Operator as shown below. Display LT-C (blinking) C Maintenance Meaning Electrolytic Capacitor Maintenance Timer Monitor U1-61 has reached 100%. Cooling Fan Maintenance Timer (blinking) Monitor U1-63 has reached Fan Maintenance 100%. LT-F Probable causes Corrective Actions The electrolytic capacitors have Reset constant o2-18 to “0%” after reached their estimated maintenance replacing the electrolytic capacitors. time period. The cooling fan has reached its estimated maintenance time period. Replace the cooling fan and set constant o2-10 to “0H”. Settings Required After Replacement of Cooling Fan or Electrolytic Capacitor • Set o2-10 to 0 after replacing the cooling fan. • Set o2-18 to 0 after replacing the electrolytic bus capacitor. Refer to Chapter 8 Maintenance and Inspection for the replacement procedure. Related Constants Name Constant Number Display o2-10 Fan operation time setting * o2-18 * Control Methods Description Set the initial value of the fan operation time using time units. Fan ON Time The operation time accumulates from the set value. Set Capacitor maintenance setting C MaintenanceSet Allows the user to set the maintenance time for the electrolytic capacitors (U161). The user can reset the accumulated operation time back to zero, or to some other desired value. Setting Range Factory Setting Change during Operation 0 to 65535 0 hr 0 to 150 0% * Applicable for G7-Series Inverters with software versions PRG: 1039 or later. 6-184 Open MEMOBUS Loop Vec- Register tor 2 V/f V/f with PG Open Loop Vector 1 Flux Vector No A A A A A 50EH No A A A A A 51DH 7 Troubleshooting This chapter describes the fault displays and countermeasure for the Inverter and motor problems and countermeasures. Protective and Diagnostic Functions ...........................7-2 Troubleshooting .........................................................7-25 Protective and Diagnostic Functions This section describes the alarm functions of the Inverter. The alarm functions include fault detection, alarm detection, operation error detection, and autotuning error detection. Fault Detection When the Inverter detects a fault, the fault contact output operates, and the Inverter output is shut OFF causing the motor to coast to a stop. (The stopping method can be selected for some faults, and the selected stopping method will be used with these faults.) A fault code is displayed on the Digital Operator. When a fault has occurred, refer to the following table to identify and correct the cause of the fault. Use one of the following methods to reset the fault before restarting the Inverter: • Set a multi-function contact input (H1-01 to H1-05) to 14 (Fault Reset) and turn ON the fault reset signal. • Press the RESET Key on the Digital Operator. • Turn the main circuit power supply OFF and then ON again. Table 7.1 Fault Displays and Processing Display Meaning Probable Causes Corrective Actions • A short-circuit or ground fault occurred at the Inverter output. (A short or ground fault can be caused by motor burn damage, worn insulation, or a damaged cable.) • The load is too large or the acceleration/deceleration time is too short. • A special-purpose motor or motor with a capacity too large for the Inverter is being used. • A magnetic contactor was switched at the Inverter output. Reset the fault after correcting its cause. Note) Before turning the power ON again, make sure that no short-circuit or ground fault occurs at the Inverter output. Overcurrent OC The Inverter output current exceeded Over Curthe overcurrent detection level. (200% There is a break in the PG wiring. rent of rated current) The PG is wired incorrectly. Power isn't being supplied to the PG. Fix the broken/disconnected wiring. Fix the wiring. Supply power to the PG properly. • Make sure that incorrect wiring has not been done. • A short-circuit between +V, −V, and • Check the resistance and wirAC terminals occurred. ing for the frequency setting • Overload in the control circuit terpotentiometer, etc. (Check that minal. the current for terminals +V and –V is 20 mA or less.) GF Ground Fault Ground Fault* The ground fault current at the Inverter output exceeded approximately 50% of the Inverter rated output current. A ground fault occurred at the Inverter output. (A ground fault can be caused by motor burn damage, worn insulation, or a damaged cable.) Reset the fault after correcting its cause. Note) Before turning the power ON again, make sure that no short-circuit or ground fault occurs at the Inverter output. • Make sure that incorrect wiring has not been done. • A short-circuit between +V, −V, and • Check the resistance and wirAC terminals occurred. ing for the frequency setting • Overload in the control circuit terpotentiometer, etc. (Check that minal. the current for terminals +V and –V is 20 mA or less.) * The ground fault here is one which occurs in the motor wiring while the motor is running. A ground fault may not be detected in the following cases. y A ground fault with low resistance which occurs in motor cables or terminals. y A ground fault occurs when the power is turned ON. 7-2 Protective and Diagnostic Functions Table 7.1 Fault Displays and Processing (Continued) Display Meaning PUF Main IGBT Fuse Blown Fuse The fuse in the main circuit is blown. Blown Probable Causes Corrective Actions The output transistor has failed because of a short-circuit or ground fault at the Inverter output. Check whether there is a short-circuit between the following terminals. A short-circuit will damage the output transistor: B1 ( 3) ←→ U, V, W ←→ U, V, W Replace the Inverter after correcting the cause. Increase the deceleration time or connect a braking resistor (or The deceleration time is too short and Braking Resistor Unit). Alternathe regenerative energy from the tively, enable (set to 1) the stall motor is too large. prevention selection during deceleration (L3-04). OV DC Bus Overvolt Main Circuit Overvoltage The main circuit DC voltage exceeded the overvoltage detection level. 200 V Class: Approx. 410 V 400 V Class: Approx. 820 V (E1-01 ≥ 400 V) Approx. 720 V (E1-01 < 400 V) Main Circuit Undervoltage The main circuit DC voltage is below the Undervoltage Detection Level (L2-05). 200 V Class: Approx. 190 V 400 V Class: Approx. 380 V UV1 DC Bus Main Circuit Magnetic Connector Undervolt Operation Failure The magnetic connector stopped responding during Inverter operation. Applicable Inverter Capacities 200 V Class: 37 to 110 kW 400 V Class: 75 to 300 kW Motor ground fault (Ground fault current flowed to the capacitor in the control circuit of the Inverter through the power supply.) Check the output cable, relay terminal, or motor terminal box and correct the cause of ground fault. Incorrect constant setting for speed search (The speed search can be performed during momentary power loss recovery and auto restart after a fault.) • Use the speed search function. • Adjust the settings of the Speed search operating current (b3-02) and Speed search deceleration time (b3-03). • Use the estimated speed search function. (Perform stationary autotuning for line-to-line resistance only.) Improper PG cable connection (PG noise, PG disconnection) Check to see if the PG cable is connected properly. The regenerative energy when an overshoot occurs after acceleration is completed is too large. In vector control, enable (set to 1) the overvoltage inhibit selection (L3-11). The power supply voltage is too high. Decrease the voltage so it’s within specifications. • An open-phase occurred with the input power supply. • A momentary power loss occurred. • The wiring terminals for the input power supply are loose. • The voltage fluctuations in the input power supply are too large. • A fault occurred in the surge prevention circuit. • The magnetic contactor in the control circuit was released (Contact failure in the auxiliary contact). • The contact of the magnetic contactor in the control circuit was corroded due to environmental dust or gas. • Reset the fault after correcting its cause. • Improve the power supply environment. (Check to see if the correct power tap is selected.) • Improve the operating environment. • Replace the Inverter. 7-3 Table 7.1 Fault Displays and Processing (Continued) Display Meaning UV2 Control Power Fault CTL PS The control power supply voltage Undervolt dropped. Corrective Actions • The wiring of the control power circuit is incorrect. • A Backup Capacitor Unit for • Try turning the power supply Momentary Power Loss is not off and on. attached to a 200 V/400 V Class • Replace the Inverter if the fault Inverter of 7.5 kW or less and the continues to occur. value of the Momentary power loss • Attach a Backup Capacitor Unit ridethru time (L2-02) factory setting for Momentary Power Loss. has been changed to the larger value. UV3 MC Answerback Inrush Prevention Circuit Fault A fault occurred in the surge preven• The magnetic contactor in the main • Try turning the power supply tion circuit. circuit failed. off and on. The magnetic contactor did not • The magnetic contactor excitation • Replace the Inverter if the fault respond for 10 s even though the magcoil is burned out. continues to occur. netic contactor ON signal has been output. PF Input Pha Loss Main Circuit Voltage Fault The main circuit DC voltage oscillates unusually (not when regenerating). This fault is detected if a load is greater than approximately 80% of the maximum motor capacity. This fault is detected when L8-05 is set to 1. Output Open-phase An open-phase occurred at the LF Output Pha Inverter output. This fault is detected when L8-07 is Loss set to 1 or 2 OH (OH1) Heatsnk Overtemp (Heatsnk MAX Temp) Cooling Fin Overheating The temperature of the Inverter's cooling fins exceeded the setting in L8-02 or the overheat protection level. OH: The temperature exceeded the setting in L8-02 (Stopping method can be changed by L8-03.). OH1: The temperature exceeded 100°C (Stopping method: Coast to stop). Inverter's Cooling Fan Fault (200 V Class: 7.5 kW or more, 400 V Class: 5.5 kW or more) This fault is detected when L8-32 is set to 1. 7-4 Probable Causes • An open-phase occurred in the input power supply. • A momentary power loss occurred. • The wiring terminals for the input Reset the fault after correcting its power supply are loose. cause. • The voltage fluctuations in the input power supply are too large. • The voltage balance between phases is bad. • There is a broken wire in the output cable. Reset the fault after correcting its • There is a broken wire in the motorcause. winding. • The output terminals are loose. The motor being used has a capacity less than 5% of the rated output current. Check the motor and Inverter capacity. The ambient temperature is too high. Install a cooling unit. There is a heat source nearby. Remove the heat source. The Inverter's cooling fan has stopped. Replace the cooling fan. (Contact our sales representative.) • Make sure that incorrect wiring has not been done. • A short-circuit between +V, −V, and • Check the resistance and wirAC terminals occurred. ing for the frequency setting • Overload in the control circuit terpotentiometer, etc. (Check that minal. the current for terminals +V and –V is 20 mA or less.) • The Inverter's cooling fan has stopped. • The heatsink is clogged. • Replace the cooling fan. (Contact our sales representative.) • Clean the heatsink. Protective and Diagnostic Functions Table 7.1 Fault Displays and Processing (Continued) Display Meaning FAN Cooling Fan Fault Inverter’s Cooling Fan Fault An Inverter’s cooling fan fault was detected, and the Inverter-overload protection was activated based on the internal electric thermal value. This fault is detected when L8-32 is set to 0. Probable Causes The Inverter continued running with an overload after the cooling fan stopped. Motor Overheating Alarm OH3 The Inverter will stop or will continue Motor The motor has overheated. to operate according to the setting of Overheat 1 L1-03. OH4 Motor Overheating Fault Motor The Inverter will stop according to the The motor has overheated. Overheat 2 setting of L1-04. Corrective Actions Replace the cooling fan. (Contact our sales representative.) Check the size of the load and the length of the acceleration, deceleration, and cycle times. Check the V/f characteristics. Check the Motor Rated Current (E2-01). Check the size of the load and the length of the acceleration, deceleration, and cycle times. Check the V/f characteristics. Check the Motor Rated Current (E2-01). • The deceleration time is too short and the regenerative energy from the motor is too large. • RH DynBrk Resistor Installed Braking Resistor Overheating Braking resistor protection function set in L8-01 has operated. RR DynBrk Transistr Internal Braking Transistor Fault • The braking transistor is damaged. The braking transistor is not operating • The Inverter’s control circuits are properly. faulty. Reduce the load, increase the deceleration time, or reduce the motor speed. Change to a Braking Resistor Unit. • Try turning the power supply off and on. • Replace the Inverter if the fault continues to occur. 7-5 Table 7.1 Fault Displays and Processing (Continued) Display Meaning Probable Causes Corrective Actions The load is too heavy. The acceleraCheck the size of the load and the tion time, deceleration time, and cycle length of the acceleration, decelertime are too short. ation, and cycle times. The constant setting for speed search is incorrect. (Motor overload occurred due to motor hunting and vibration.) • Use the speed search function. • Adjust the settings of the Speed search operating current (b3-02) and Speed search deceleration time (b3-03). • Use the estimated speed search function. (Perform stationary autotuning for line-to-line resistance only.) • Motor overload occurred when running at low speed. (If a general-purpose motor is used, motor overload can occur when running at low • Check the size of the load. speed even if running within the • Check the setting of L1-01. rated current.) • Increase the frame size of the Motor Overload • Motor protection selection (L1-01) Inverter. OL1 The motor overload protection funcis set to general-purpose motor proMotor tion has operated based on the internal tection (1) when an Inverter duty Overloaded electronic thermal value. motor is used. • Correct the PG wiring. The directions of the motor and PG • Correct the motor wiring. are different. (Only in flux vector con• Change the setting of PG rotatrol) tion (F1-05). The V/f characteristics voltage is too high. Check the V/f characteristics. The Motor Rated Current (E2-01) is incorrect. Check the Motor Rated Current (E2-01). • Make sure that incorrect wiring has not been done. • A short-circuit between +V, −V, and • Check the resistance and wirAC terminals occurred. ing for the frequency setting • Overload in the control circuit terpotentiometer, etc. (Check that minal. the current for terminals +V and –V is 20 mA or less.) 7-6 Protective and Diagnostic Functions Table 7.1 Fault Displays and Processing (Continued) Display Meaning Probable Causes Corrective Actions The load is too heavy. The acceleration time, deceleration time and cycle time are too short. Check the size of the load and the length of the acceleration, deceleration, and cycle times. The constant setting for speed search is incorrect. (Motor overload occurred due to motor hunting and vibration.) • Use the speed search function. • Adjust the settings of the Speed search operating current (b3-02) and Speed search deceleration time (b3-03). • Use the estimated speed search function. (Perform stationary autotuning for line-to-line resistance only.) • Correct the PG wiring. The directions of the motor and PG • Correct the motor wiring. are different. (Only in flux vector con• Change the setting of PG rotaInverter Overload trol) OL2 tion (F1-05). The Inverter overload protection funcInv Overtion has operated based on the internal The V/f characteristics voltage is too loaded Check the V/f characteristics. electronic thermal value. high. The Inverter capacity is too low. Replace the Inverter with one that has a larger capacity. • Make sure that incorrect wiring has not been done. • A short-circuit between +V, −V, and • Check the resistance and wirAC terminals occurred. ing for the frequency setting • Overload in the control circuit terpotentiometer, etc. (Check that minal. the current for terminals +V and –V is 20 mA or less.) Overtorque Detected 1 OL3 There has been a current greater than Overtorque the setting in L6-02 for longer than the Det 1 setting in L6-03. Overtorque Detected 2 OL4 There has been a current greater than Overtorque the setting in L6-05 for longer than the Det 2 setting in L6-06. OL7 HSB-OL High-slip Braking OL The output frequency did not change for longer than the time set in N3-04. Inverter overload occurred when running at a low speed of 6 Hz or less. • Reduce the load. • Increase the frame size of the Inverter. • Lower the carrier frequency. - • Make sure that the settings in L6-02 and L6-03 are appropriate. • Check the mechanical system and correct the cause of the overtorque. - • Make sure that the current setting in L6-05 and time setting in L6-06 are appropriate. • Check the mechanical system and correct the cause of the overtorque. The inertia returned to the load is too large. • Make sure the load is an inertial load. • Set the system so that the deceleration time that does not produce overvoltages is 120 s or less. 7-7 Table 7.1 Fault Displays and Processing (Continued) Display Meaning Undertorque Detected 1 UL3 There has been a current less than the Undertorq setting in L6-02 for longer than the Det 1 setting in L6-03. Undertorque Detected 2 UL4 There has been a current less than the Undertorq setting in L6-05 for longer than the Det 2 setting in L6-06. Overspeed OS The speed has been greater than the Overspeed setting in F1-08 for longer than the Det setting in F1-09. PGO PG Open DEV Speed Deviation PG Disconnection Detected PG pulses were input when the Inverter was outputting a frequency. Excessive Speed Deviation The speed deviation has been greater than the setting in F1-10 for longer than the setting in F1-11. Probable Causes - • Make sure that the settings in L6-02 and L6-03 are appropriate. • Check the mechanical system and correct the cause of the overtorque. - • Make sure that the current setting in L6-05 and time setting in L6-06 are appropriate. • Check the mechanical system and correct the cause of the overtorque. Overshooting/Undershooting are occurring. Adjust the gain again. The reference speed is too high. Check the reference circuit and reference gain. The settings in F1-08 and F1-09 aren't Check the settings in F1-08 and appropriate. F1-09. There is a break in the PG wiring. Fix the broken/disconnected wiring. The PG is wired incorrectly. Fix the wiring. Power isn't being supplied to the PG. Supply power to the PG properly. Brake is applied to the motor. Check for open circuit when using brake (motor). The load is too heavy. Reduce the load. The acceleration time and deceleration Lengthen the acceleration time time are too short. and deceleration time. The load is locked. FBL Feedback Loss 7-8 Check the mechanical system. The settings in F1-10 and F1-11 aren't Check the settings in F1-10 and appropriate. F1-11. Brake is applied to the motor. CF Out of Control Corrective Actions Control Fault The torque limit was reached continuMotor constant settings are not corously for 3 seconds or longer during a rect. deceleration stop during open-loop vector 1 control. Check for open circuit when using brake (motor). • Check the motor constants. • Perform autotuning. An error occurred in the speed estimation calculation for open-loop vector 2 Refer to Corrective Actions for Control Faults (CF) on page 7-14. control. PID Feedback Reference Lost A PID feedback reference loss was detected (b5-12 = 2) and the PID feedback input was less than b5-13 (PID feedback loss detection level) for longer than the time set in b5-14 (PID feedback loss detection time). The settings in b5-13 and b5-14 aren’t Check the settings in b5-13 and appropriate. b5-14. The wiring of the PID feedback circuit Fix the wiring. is incorrect. Protective and Diagnostic Functions Table 7.1 Fault Displays and Processing (Continued) Display Meaning EF0 External Fault Input from CommuOpt Externications Option Board nal Flt EF3 Ext Fault S3 External Fault (Input Terminal 3) EF4 Ext Fault S4 External Fault (Input Terminal 4) EF5 Ext Fault S5 External Fault (Input Terminal 5) EF6 Ext Fault S6 External Fault (Input Terminal 6) EF7 Ext Fault S7 External Fault (Input Terminal 7) EF8 Ext Fault S8 External Fault (Input Terminal 8) EF9 Ext Fault S9 External Fault (Input Terminal 9) EF10 Ext Fault S10 External Fault (Input Terminal 10) EF11 Ext Fault S11 External Fault (Input Terminal 11) EF12 Ext Fault S12 External Fault (Input Terminal 12) SVE Zero-servo Fault Zero Servo The rotation position moved during Fault zero-servo operation. SER Search Retrials Fault Exceeded Allowable Number of Speed Search Retrials The speed search has been retried more than the number of times set in b3-19 (Number of speed search retrials). OPR Oper Disconnect Digital Operator Connection Fault The connection to the Digital Operator was broken during operation for a Run Command from the Digital Operator. Probable Causes - Corrective Actions Check the Communications Option Board and communications signals. An “external fault” was input from a multi-function input terminal. • Reset external fault inputs to the multi-function inputs. • Remove the cause of the external fault. The torque limit is too small. Increase the limit. The load torque is too large. Reduce the load torque. - Check for signal noise. The settings in b3-17 and b3-18 aren’t Make sure that the settings in b3appropriate. 17 and b3-18 are appropriate. - Check the connection to the Digital Operator. 7-9 Table 7.1 Fault Displays and Processing (Continued) Display Meaning CE Memobus Com Err MEMOBUS Communications Error A normal reception was not possible for 2 s or longer after control data was received once. BUS Option Com Err Option Communications Error A communications error was detected during a Run Command or while setting a frequency reference from a Communications Option Board. E5 SI-T Watchdog Error SI-T WDT Consistency error of received control Err data E-15 SI-F/G Com Err SI-F/G Communications Error Detected A communications error was detected when a Run Command or frequency reference was set from an option board and continuous operation was set for the E-15 operation selection. Probable Causes - - CPU External RAM Fault CPF01 COM-ERR (OP & INV) Digital Operator Communications Error 2 After communications were established, there was a communications error with the Digital Operator for more than 2 seconds. CPF02 BB Circuit Baseblock Circuit Error Err - 7-10 Check the communications devices and communications signals. Check the communications signals. Disconnect and then reconnect the Digital Operator. Replace the Inverter. The Digital Operator's connector isn't connected properly. Disconnect the Digital Operator and then connect it again. The Inverter's control circuits are faulty. Replace the Inverter. - Try turning the power supply off and on again. The control circuits were destroyed. Replace the Inverter. The Digital Operator isn't connected properly. Disconnect the Digital Operator and then connect it again. The Inverter's control circuits are faulty. Replace the Inverter. The control circuit is damaged. - CPF03 EEPROM EEPROM Error Error Check the communications devices and communications signals. Check the communications timing such as communications cycle. Synchronization error between master Refer to MECHATROLINK COMcontroller and Inverter for control MUNICATIONS INTERFACE data. CARD INSTRUCTIONS (TOBPC73060008) for details. E-10 Digital Operator connection is faulty. SI-F/G Option Board CPU Failure SI-F/G SI-F/G Option Board operation failed. CPU down Inverter control circuit is faulty. Digital Operator Communications Error 1 Communications with the Digital Operator were not established within 5 CPF00 COM-ERR seconds after the power was turned on. (OP & INV) Corrective Actions Try turning the power supply off and on again. Replace the Inverter. Try turning the power supply off and on again. The Inverter power supply was shut off while writing data to the Inverter constants. Initialize the constant settings (A1-03). The control circuit is damaged. Replace the Inverter. Protective and Diagnostic Functions Table 7.1 Fault Displays and Processing (Continued) Display Meaning Probable Causes The control circuit is damaged. CPF04 Internal A/D Err CPU Internal A/D Converter Error The control circuit is damaged. CPF06 Option error CPF07 RAM-Err CPF08 WAT-Err CPU External A/D Converter Error Option Board Connection Error ASIC Internal RAM Fault CPU-ASIC Mutual Diagnosis Fault CPF10 ASIC-Err ASIC Version Fault CPF20 Option A/D error Communications Option Board A/ D Converter Error CPF21 Communications Option Board Option Self Diagnostic Error CPU down CPF22 Option Type Err Try turning the power supply off and on again. Replace the Inverter. The option board is not connected properly. Turn off the power and insert the board again. The Inverter or option board is faulty. Replace the option board or the Inverter. - Try turning the power supply off and on again. The control circuit is damaged. CPF09 CPU-Err Replace the Inverter. • Make sure that incorrect wiring has not been done. • A short-circuit between +V, −V, and • Check the resistance and wirAC terminals occurred. ing for the frequency setting • Overload in the control circuit terpotentiometer, etc. (Check that minal. the current for terminals +V and –V is 20 mA or less.) The control circuit is damaged. Watchdog Timer Fault Try turning the power supply off and on again. • Make sure that incorrect wiring has not been done. • A short-circuit between +V, −V, and • Check the resistance and wirAC terminals occurred. ing for the frequency setting • Overload in the control circuit terpotentiometer, etc. (Check that minal. the current for terminals +V and –V is 20 mA or less.) - CPF05 External A/D Err Corrective Actions - Replace the Inverter. Try turning the power supply off and on again. Replace the Inverter. Try turning the power supply off and on again. The control circuit is damaged. Replace the Inverter. The Inverter control circuit is faulty Replace the Inverter. The option board is not connected properly. Turn off the power and insert the board again. The option board's A/D converter is faulty. Replace the Communications Option Board. Communications Option Board fault. Replace the option board. Communications Option Board Model Code Error 7-11 Table 7.1 Fault Displays and Processing (Continued) Display Meaning Probable Causes Communications Option Board fault. CPF23 Option DPRAM Err VCF Vcn Failure Communications Option Board DPRAM Error Main Circuit Capacitor Neutral Point Potential Error An excessive imbalance occurred in the main circuit capacitor’s neutral point potential. Corrective Actions Replace the option board. • Use the copy function off-line. The copy function of the Digital Oper• Use the copy function with an ator was used during communications. option board removed. The option board is not connected properly. Turn off the power and insert the board again. A loss in capacity due to aging of the main circuit capacitor. Replace the main circuit capacitor. (Consult your YASKAWA representative.) The Inverter parts are faulty. Replace the Inverter. An open phase was detected for an output. Refer to LF (output open phase) in this table. Carrier frequency set value (C6-03, C6-04) is unsuitable. Check the set values for C6-03 and C6-04. The maximum output frequency that can be set for 400 V Class Inverters is restricted by the carrier frequency setting. Refer to page 6-45. • Reduce the load. In V/f or open-loop vector control, the • Increase the acceleration time. motor consecutively loses synchro• Check the settings for V/f connism (the output current exceeds trol. 200% of the Inverter rated current). • Use larger capacity Inverter. OPERATOR ERR RAM CHECK ERR Operator Error (Internal RAM Fault) At power ON, an error was detected from the results of the internal RAM Write/Read check. OPERATOR ERR ROM CHECK ERR Operator Error (CPU Internal ROM Fault) At power ON and during operation, an error was detected when the internal ROM was checked. OPERATOR ERR DATA SEND ERR Operator Error (Transmission Circuit Fault) During operation, send processing did not complete within 500 ms continuously at least 10 times. OPERATOR ERR RAM CHECK ERR Operator Error (Internal RAM Fault) During operation, an error was detected when the display pattern for the character code 80 to 8F recorded in the internal RAM was checked. OPERAOperator Error (Watchdog Error) TOR ERR During operation, an error was WATCHdetected in the program execution. DOG ERR 7-12 --- Replace the Operator. Protective and Diagnostic Functions Table 7.2 Causes and Corrective Actions When the Digital Operator Goes Dark Display Meaning Probable Causes Corrective Actions • Make sure that incorrect wiring has not been done. • A short-circuit between +V, −V, and • Check the resistance and wirAC terminals occurred. ing for the frequency setting • Overload in the control circuit terpotentiometer, etc. (Check that minal. the current for terminals +V and –V is 20 mA or less.) The short-circuit bar between +1 and +2 terminals in the main circuit has been removed. Attach the short-circuit bar. • Check the wiring for the Braking Unit, including cables conP terminal and N terminal of the BrakThere was a drop in control power nected to the Braking Unit and No display ing Unit are connected in reverse. voltage. relay terminals. • Replace the Inverter. Control power circuit failure Charge indicator is lit: • Replace the Digital Operator. • Replace the board or the Inverter. Charge indicator is not lit: • Check the input power supply voltage. • Replace the Inverter. Malfunction occurred in the control power circuit. Turn OFF the power, wait for 5 minutes, and turn ON the power again. 7-13 Corrective Actions for Control Faults (CF) CF occurs No Are the motor and Inverter connected properly? Fix the wiring. Yes U1-50 = 01,02 No Execute autotuning for the Are the motor constants set correctly? motor constants. Refer to Autotuning on page 4-9. Execute autotuning after the control method is changed. Yes Has autotuning been executed for line-to-line resistance? U1-50 = 00,01, No 02,08 Execute autotuning for the line-to-line resistance. Refer to Autotuning on page 4-9. Execute autotuning after changing cables. Yes Are the torque limit settings (L7-01 to L7-04, analog input) or the torque reference input too small? No Is the stopping method appropriate? Increase the torque limit or torque reference until is it within the allowable range for the machine. Yes U1-50 = 00 If deceleration stop is not No possible or unnecessary for the machine, set b1-03 to 1 (coast to stop). Yes U1-50 = 02 · Input the operation reference Is an operation reference being input while the motor is coasting? Yes after the motor stops. · Set b3-01 to 1 or 3 (speed search enabled). Refer to Torque Limits: L7 on page 5-65. In particular, if the regenerative torque limit has been reduced to prevent overvoltages, set L3-11 to 1 and set the regenerative torque limit to a large value. Refer to Speed Search on page 6-64. No U1-50 = 04 What is the CF error code (U1-50)? U1-50 = 08 Adjust the speed estimator's integral time (N4-07) or proportional gain (N4-08). Refer to Procedure for Increasing the Speed Response (PRG: 102 only) on page 4-21. If the machine rotates only in the same direction as the sign of the speed limit, set b1-10 to 1. U1-50 = 10 · If the machine rotates only in the same direction as the sign of the speed limit (winding operation), set d5-07 to 1. · Ensure that the motor's speed is not 0 or that it does not rotate in the opposite direction. U1-50 = 20 Use in open loop vector 1 control. · If the machine rotates in the opposite direction to the sign of the speed limit (rewinding operation), set d5-07 to 0. · Start with speed control and then switch to torque control when the frequency exceeds 3 Hz. Meaning of CR Error Codes U1-50 7-14 Meaning 00 Stop error 01 Magnetic flux calculation error 1 02 Magnetic flux calculation error 2 04 Speed estimator gain adjustment fault 08 Low-speed regeneration fault 10 Zero-speed fault 20 Rotation direction limit fault Refer to Speed/Torque Control Switching Function on page 6-134. Protective and Diagnostic Functions Alarm Detection Alarms are detected as a type of Inverter protection function that do not operate the fault contact output. The system will automatically returned to its original status once the cause of the alarm has been removed. The Digital Operator display blinks and an alarm is sent from the multi-function outputs (H2-01 to H2-05) if selected. When an alarm occurs, take appropriate countermeasures according to the table below. Table 7.3 Alarm Displays and Processing Display Meaning Forward/Reverse Run Commands Input Together (blinking) Both the forward and Reverse Run External Commands have been ON for more Fault than 0.5 s. Probable causes Corrective Actions - Check the sequence of the forward and Reverse Run Commands. Since the rotational direction is unknown, the motor will be decelerated to a stop when this minor fault occurs. EF Main Circuit Undervoltage The following conditions occurred when there was no Run signal. UV • The main circuit DC voltage was (blinking) below the Undervoltage Detection DC Bus Level Setting (L2-05). Under• The surge current limiting magvolt netic contactor opened. • The control power supply voltage when below the CUV level. See causes for UV1, UV2, and UV3 faults in the previous table. See corrective actions for UV1, UV2, and UV3 faults in the previous table. Main Circuit Overvoltage The main circuit DC voltage exceeded (blinking) Decrease the voltage so it's within the overvoltage detection level. The power supply voltage is too high. DC Bus specifications. 200 V Class: Approx. 410 V Overvolt 400 V Class: Approx. 820 V OV OH (blinking) Heatsink Overtemp FAN (blinking) Cooling Fan Fault Cooling Fin Overheating The temperature of the Inverter's cooling fins exceeded the setting in L8-02. Inverter’s Cooling Fan Fault An Inverter’s cooling fan fault was detected. This fault is detected when L8-32 is set to 0. Inverter Overheating Pre-alarm An OH2 alarm signal (Inverter over(blinking) heating alarm signal) was input from a Over multi-function input terminal (S3 to Heat 2 S7). The ambient temperature is too high. Install a cooling unit. There is a heat source nearby. Remove the heat source The Inverter cooling fan has stopped. Replace the cooling fan. (Contact your Yaskawa representative.) • Make sure that incorrect wiring has • A short-circuit between +V, −V, and not been done. AC terminals occurred. • Check the resistance and wiring for • Overload in the control circuit terthe frequency setting potentiometer, minal. etc. (Check that the current for terminals +V and –V is 20 mA or less.) The Inverter’s cooling fan has stopped. Replace the cooling fan. (Contact our sales representative.) OH2 - Clear the multi-function input terminal's overheating alarm input. 7-15 Table 7.3 Alarm Displays and Processing (Continued) Display OH3 (blinking) Motor Overheat 1 OL3 (blinking) Overtorque Det 1 OL4 (blinking) Overtorque Det 2 Meaning Probable causes Motor Overheating E was set for H3-09 and the motor The motor has overheated. temperature thermistor input exceeded the alarm detection level. Overtorque 1 There has been a current greater than the setting in L6-02 for longer than the setting in L6-03. Overtorque 2 There has been a current greater than the setting in L6-05 for longer than the setting in L6-06. - - • Make sure that the settings in L6-02 and L6-03 are appropriate. • Check the mechanical system and correct the cause of the overtorque. - • Make sure that the current setting in L6-05 and time setting in L6-06 are appropriate. • Check the mechanical system and correct the cause of the overtorque. UL4 (blinking) Overspeed Det Overspeed The speed has been greater than the setting in F1-08 for longer than the setting in F1-09. Overshooting/undershooting are occurring. Adjust the gain again. The reference speed is too high. Check the reference circuit and reference gain. The settings in F1-08 and F1-09 aren't Check the settings in F1-08 and F1-09. appropriate. There is a break in the PG wiring. The PG is wired incorrectly. The PG is Disconnected (blinking) The Inverter is outputting a frequency, Power isn't being supplied to the PG. PG Open but PG pulses aren't being input. PGO DEV (blinking) Speed Deviation Excessive Speed Deviation The speed deviation has been greater than the setting in F1-10 for longer than the setting in F1-11. Fix the broken/disconnected wiring. Fix the wiring. Supply power to the PG properly. Brake is applied to the motor. Check for open circuit when using brake (motor). The load is too large. Reduce the load. The acceleration time and deceleration time are too short. Lengthen the acceleration time and deceleration time. The load is locked. Check the mechanical system. The settings in F1-10 and F1-11 aren't Check the settings in F1-10 and F1-11. appropriate. Brake is applied to the motor. 7-16 Check the motor temperature input on terminals A1 and A2. • Make sure that the current setting in L6-05 and time setting in L6-06 are appropriate. • Check the mechanical system and correct the cause of the overtorque. (blinking) OS Check the V/f characteristics. - (blinking) Undertorque 2 There has been a current less than the Undersetting in L6-05 for longer than the torq Det setting in L6-06. 2 Check the size of the load and the length of the acceleration, deceleration, and cycle times. • Make sure that the settings in L6-02 and L6-03 are appropriate. • Check the mechanical system and correct the cause of the overtorque. UL3 Undertorque 1 There has been a current less than the Undersetting in L6-02 for longer than the torq Det setting in L6-03. 1 Corrective Actions Check for open circuit when using brake (motor). Protective and Diagnostic Functions Table 7.3 Alarm Displays and Processing (Continued) Display Meaning External Fault Detected for Communications Board Other Than (blinking) SI-K2 Opt Continuing operation was specified External for EF0 (F6-03 = 3)and an external Flt fault was input from the option board. Probable causes Corrective Actions - Remove the cause of the external fault. EF0 EF3 (blinking) Ext Fault S3 External Fault (Input Terminal S3) EF4 (blinking) Ext Fault S4 External Fault (Input Terminal S4) EF5 (blinking) Ext Fault S5 External Fault (Input Terminal S5) EF6 (blinking) Ext Fault S6 External Fault (Input Terminal S6) EF7 (blinking) Ext Fault S7 External Fault (Input Terminal S7) An external fault was input from a multi-function input terminal (S3 to S7). EF8 (blinking) Ext Fault S8 External Fault (Input Terminal S8) • Reset external fault inputs to the multi-function inputs. • Remove the cause of the external fault. EF9 (blinking) Ext Fault S9 External Fault (Input Terminal S9) EF10 (blinking) Ext Fault S10 External Fault (Input Terminal S10) EF11 (blinking) Ext Fault S11 External Fault (Input Terminal S11) EF12 (blinking) Ext Fault S12 External Fault (Input Terminal S12) PID Feedback Reference Lost A PID feedback reference loss was (blinking) detected (b5-12 = 2) and the PID feedFeed- back input was less than b5-13 (PID back feedback loss detection level) for Loss longer than the time set in b5-14 (PID feedback loss detection time). FBL The settings in b5-13 and b5-14 aren’t Check the settings in b5-13 and b5-14. appropriate. The wiring of the PID feedback circuit is incorrect. Fix the wiring. 7-17 Table 7.3 Alarm Displays and Processing (Continued) Display Meaning Probable causes Corrective Actions CE MEMOBUS Communications Error Normal reception was not possible for MEMO 2 s or longer after received control BUS data. Com Err - Check the communications devices and signals. Option Board Communications Error (blinking) A communications error occurred in a Option mode where the Run Command or a Com Err frequency reference is set from an Communications Option Board. - Check the communications devices and signals. Communications on Standby Control data was not normally received when power was turned ON. - Check the communications devices and signals. Reset during Run Command Input Error (blinking) The reset signal was input during Run Ext Run Command input from an external terActive minal or other source. - Check that a Run Command is not being input from an external terminal or other source. (blinking) BUS CALL (blinking) Com Call RUNC E5 (blinking) SI-T WDT Err SI-T Watchdog Error Detected A Watchdog error was detected when Synchronization error between master Check the communications timing the Run Command or a frequency refcontroller and Inverter for control erence was set from an option board such as communications cycle. *1 data. and continuous operation was set for the E5 operation selection. AEr (blinkSI-T Station Number Setting Error ing) Station number of SI-T option board SI-T was out of setting range. Address Err 7-18 Station number setting error. Check the setting of the station number. *1 Circuit of SI-T option board is faulty. Check the communications devices and signals. *1 CyC (blinking) SI-T Cycle Err SI-T Communications Cycle SetCommunications cycle of SI-T option Check the communication cycle of SIting Error board set in master controller was out T option board set in master controlCommunications cycle of SI-T option of range. ler.*1 board was out of range. BB (blinking) Baseblock Receiving External Baseblock Command An external baseblock signal was input from a multi-function input terminal, and the Inverter output was shut down. An external baseblock signal was input from a multi-function input terminal. Check the external sequence. Protective and Diagnostic Functions Table 7.3 Alarm Displays and Processing (Continued) Display Meaning Probable causes The load is too heavy or the accel/ decel time is too short. HCA (blinking) High Current Alarm Either a specialized motor or an Current Alarm excessively large motor is being used. The output current has exceeded the overcurrent alarm level (over 150% of the rated current). The current has risen too high while performing speed search either during a momentary loss in power or during a fault restart. Corrective Actions Increase the acceleration/deceleration time. Verify the setting for the Inverter capacity. Momentary losses in power or fault restarts may occasionally trigger an overcurrent alarm, and are not necessarily indicators of an overcurrent problem. LT-C (blinkElectrolytic Capacitor Maintenance The electrolytic capacitors have ing) Timer reached their estimated maintenance C Monitor U1-61 has reached 100%. time period. Maintenance Reset constant o2-18 to “0%” after replacing *2 the electrolytic capacitors. LT-F (blinking) Cooling Fan Maintenance Timer Fan Monitor U1-63 has reached 100%. Maintenance Replace the cooling fan *2 and set constant o2-10 to “0H”. The cooling fan has reached its estimated maintenance time period. * 1. Refer to MECHATROLINK COMMUNICATIONS INTERFACE CARD INSTRUCTIONS (TOBPC73060008) for details. * 2. For details on replacement, refer to Chapter 8 Maintenance and Inspection 7-19 Operation Errors An operation error will occur if there is an invalid setting or a contradiction between two constant settings. It won't be possible to start the Inverter until the constants have been set correctly. (The alarm output and fault contact outputs will not operate either.) When an operation error has occurred, refer to the following table to identify and correct the cause of the errors. Table 7.4 Operation Error Displays and Incorrect Settings Display OPE01 kVA Selection OPE02 Limit Meaning Incorrect Inverter Capacity Setting The Inverter capacity setting doesn't match the Unit. (Contact your Yaskawa representative.) Constant Setting Range The constant setting is outside of the valid setting range. Press the ENTER Key on Error the Digital Operator to display OPE fault constant (U1-34). OPE03 Terminal Multi-function Input Selection Error One of the following errors has been made in the multi-function input (H1-01 to H110) settings: • The same setting has been selected for two or more multi-function inputs. • An up or down command was selected independently. (They must be used together.) • The up/down commands (10 and 11) and Accel/Decel Ramp Hold (A) were selected at the same time. • Speed Search 1 (61, maximum output frequency) and Speed Search 2 (62. set frequency) were selected at the same time. • The up/down commands (10 and 11) were selected while PID Control Method Selection (b5-01) was enabled. • Positive and negative speed commands have not been set at the same time. • The emergency Stop Command NO and NC have been set at the same time. OPE05 Sequence Select Option Board Selection Error The option board was selected as the frequency reference source by setting b1-01 to 3, but an option board isn't connected (C option). OPE06 Control Method SelecPG Opt Misstion Error ing V/f control with PG feedback was selected by setting A1-02 to 1, but a PG Speed Control Board isn't connected. Multi-function Analog Input Selection Error The same setting has been selected for the analog input selection and the PID function selection. • H3-09 = B and H6-01 = 1 • H3-09 = C and H6-01 = 2 b1-01 (Reference Selection) is set to 4 (pulse input) and H6-01 (Pulse Train Input Function Selection) is set to a value other than 0 (frequency reference). OPE08 Constant Selection Error A setting has been made that is not required in the current control method. Ex.: A function used only with open-loop vector control was selected for V/f control. Press the ENTER Key on the Digital Operator to display OPE fault constant (U1-34). OPE09 PID Control Selection Error The following settings have been made at the same time. • b5-01 (PID Control Method Selection) has been set to a value other than 0. • b5-15 (PID Sleep Function Operation Level) has been set to a value other than 0. • b1-03 (Stopping Method Selection) has been set to 2 or 3. OPE10 V/f Ptrn Set- V/f Data Setting Error ting Constants E1-04, E1-06, E1-07, and E1-09 do not satisfy the following conditions: • E1-04 (FMAX) ≥ E1-06 (FA) > E1-07 (FB) ≥ E1-09 (FMIN) • E3-02 (FMAX) ≥ E3-04 (FA) > E3-05 (FB) ≥ E3-07 (FMIN) OPE07 Analog Selection 7-20 Incorrect settings Protective and Diagnostic Functions Table 7.4 Operation Error Displays and Incorrect Settings (Continued) Display Meaning Incorrect settings OPE11 Carr Freq/ On-Delay Constant Setting Error One of the following constant setting errors exists. • C6-05 (Carrier Frequency Gain) > 6, the Carrier Frequency Lower Limit (C6-04) > the Carrier Frequency Gain (C6-05) • Upper/lower limit error in C6-03 to 05. • C6-02 is 7 to E. ERR EEPROM R/W Err EEPROM Write Error A verification error occurred when writing EEPROM. • Try turning the power supply off and on again. • Try setting the constants again. Note If the settings for the constants of an Inverter with a different version of software are copied, an OPE error can occur. Contact your Yaskawa representative if wanting to copy the settings with a different software version. 7-21 Errors During Autotuning The errors that can occur during autotuning are given in the following table. If an error is detected, the motor will coast to a stop and an error code will be displayed on the Digital Operator. The error contact output and alarm output will not function. Table 7.5 Errors During Autotuning Display Meaning Probable causes Corrective Actions Data Invalid Motor data error There is an error in the data input for autotuning. There is an error in the relationship • Check the input data. between the motor output and the motor • Check the capacity of the Inverter and rated current. motor. The is an error between the no-load cur• Check the motor rated current and norent setting and the input motor rated load current. current (when autotuning for only lineto-line resistance is performed for vector control). Minor Fault Alarm A minor fault occurred during autotuning (xxx). STOP key STOP key input The STOP Key was pressed to cancel autotuning. Resistance Line-to-line resistance error No-Load Current Rated Slip Accelerate Autotuning was not completed in the specified time. No-load current error The results of autotuning has exceeded the setting range for a user constant. Rated slip error • Check the input data. • Check motor wiring. • If the motor is connected to the machine, disconnect it. • Increase C1-01 (Acceleration Time 1). Acceleration error • Increase L7-01 and L7-02 (Reverse The motor did not accelerate in the spec(detected only for Torque Limits) if they are low. ified time. rotational autotuning) • If the motor is connected to the machine, disconnect it. • Check the PG wiring. There is a faulty connection between the • Check the motor wiring. Inverter and PC (A or B phase) or the • Check the PG rotation direction and Inverter and Motor (U, V, or W). F1-05 (PG rotation). PG Direction Motor Direction Error Motor Speed Motor speed error The torque reference was too high (detected only for (100%) during acceleration (for openrotational autotuning) loop vector control only). The current flow exceeded the motor rated current. I-det. Circuit • Check the input data. • Check wiring and the machine. • Check the load. Current detection error The detected current sign was the opposite of what it should be. • If the motor is connected to the machine, disconnect it. • Increase C1-01 (Acceleration Time 1). • Check the input data (particularly the number of PG pulses and the number of motor poles). Check the current detection circuit, motor wiring, current detector, and installation methods. There is a phase fault for U, V, or W. Leakage inductance error Autotuning was not completed in the specified time. Check motor wiring. PG Open PG Disconnection Detected PG pulses were input when the Inverter was outputting a frequency. Fix the broken/disconnected wiring. V/f Over Setting V/f settings excessive* The torque reference exceeded 100% and the no-load torque exceeded 70% during autotuning. • Check and correct the settings. • Disconnect the load from the motor. Leak Inductance 7-22 Protective and Diagnostic Functions Table 7.5 Errors During Autotuning (Continued) Display Saturation Rated FLA Alm Adjusted Slip Value Meaning Probable causes Corrective Actions Motor core saturation error (detected only for rotational autotuning)* The results of autotuning has exceeded • Check the input data. the setting range for a user constant so a • Check motor wiring. temporary setting was made for the • If the motor is connected to the machine, disconnect it. motor core saturation coefficient. Rated current setting alarm* The rated current is set high. As a result of stationary autotuning 1, Adjusted slip value the slip value has fallen to 0.2 Hz or fell below lower limit below. Check the input data (particularly the motor output current and motor rated current). Check the input data. If rotational autotuning is possible, perform it. If impossible, perform stationary autotuning 2. * Displayed after autotuning has been completed. For constants in which no error is detected, the settings are reset to the values determined by autotuning. Errors when Using the Digital Operator Copy Function The errors that can occur when using the copy function from the Digital Operator are given in the following table. An error code will be displayed on the Digital Operator. If a Digital Operator key is pressed when an error code is being displayed, the display will be cleared and 03-01 will be displayed. The error contact output and alarm output will not function. Table 7.6 Errors during Copy Function Function Read Display Meaning Probable causes PRE Digital Operator READ write-protected IMPOSSIBLE o3-01 was set to 1 to write a constant when the Digital Operator was writeprotected (o3-02 = 0). IFE READ DATA ERROR The read data length does not agree. Illegal read data RDE Illegal write status DATA ERROR The write data is incorrect. Corrective Actions Set o3-02 to 1 to enable writing constants with the Digital Operator. Repeat the read. Check the Digital Operator cable. Replace the Digital Operator. A low Inverter voltage has been An attempted write of a constant to detected. EEPROM on the Digital Writer failed. Repeat the read. Replace the Digital Operator. 7-23 Table 7.6 Errors during Copy Function Function Display Meaning CPE ID not matched ID UNMATCH Copy The Inverter product code or software Use the copy function for the same number is different. product code and software number. Inverter capacity matched The capacity of the Inverter being copied and the capacity in the Digital Operator are different. Use the copy function for the same Inverter capacity. CRE CONTROL UNMATCH Control method matched The control method of the Inverter being copied and the control method in the Digital Operator are different. Use the copy function for the same control method. CYE Verify error COPY ERROR VYE VERIFY ERROR Verify error CPE ID not matched ID UNMATCH 7-24 Corrective Actions VAE INV. KVA UNMATCH CSE SUM CHECK Checksum error ERROR Verify Probable causes The constant written to the Inverter was compared with the constant in the Retry the copy. Digital Operator and they were different. The checksum in the Inverter constant area was compared with the checksum Retry the copy. in the Digital Operator constant area and they were different. The Inverter product code or software Use the copy function for the same number is different. product code and software number. The Digital Operator and Inverter setRetry the copy and verify again. tings do not agree. The Inverter product code or software Use the copy function for the same number is different. product code and software number. Troubleshooting Troubleshooting Due to constant setting errors, faulty wiring, and so on, the Inverter and motor may not operate as expected when the system is started up. If that should occur, use this section as a reference and apply the appropriate measures. If the contents of the fault are displayed, refer to Protective and Diagnostic Functions. If Constant Constants Cannot Be Set Use the following information if an Inverter constant cannot be set. The display does not change when the Increment and Decrement Keys are pressed. The following causes are possible. The Inverter is operating (drive mode). There are some constants that cannot be set during operation. Turn the Inverter off and then make the settings. Constant write enable is input. This occurs when “constant write enable” (set value: 1B) is set for a multi-function input terminal (H1-01 to H1-10). If the constant write enable input is OFF, the constants cannot be changed. Turn it ON and then set the constants. Passwords do not match. (Only when a password is set.) If the constant A1-04 (Password) and A1-05 (Password Setting) numbers are different, the constants for the initialize mode cannot be changed. Reset the password. If you cannot remember the password, display A1-05 (Password Setting) by pressing the Reset/Select Key and the Menu Key simultaneously while in the A1-04 display. Then reset the password. (Input the reset password in constant A1-04.) OPE01 through OPE11 is displayed. The set value for the constant is wrong. Refer to Operation Errors in this chapter and correct the setting. CPF00 or CPF01 is displayed. This is a Digital Operator communications error. The connection between the Digital Operator and the Inverter may be faulty. Remove the Digital Operator and then re-install it. 7-25 If the Motor Does Not Operate Use the following information if the motor does not operate. The motor does not operate when the RUN Key on the Digital Operator is pressed. The following causes are possible. IMPORTANT If the Inverter is not in drive mode and the DRIVE indicator on the Digital Operator (JVOP-161) does not light up, the Inverter will remain in ready status and will not start. Press the Menu Key to display the drive mode, and enter the drive mode by pressing the DATA/ENTER Key. “-Rdy-” will be displayed when drive mode is entered. The operation method setting is wrong. If constant b1-02 (Operation Method Selection) is set to 1 (control circuit terminal), the motor will not operate when the Run Key is pressed. Either press the LOCAL/REMOTE Key* to switch to Digital Operator operation or set b1-02 to 0 (Digital Operator). The LOCAL/REMOTE Key is enabled by setting o2-01 to 1 and disabled by setting o2-01 to 2. It is enabled when the drive mode is entered. INFO The frequency reference is too low. If the frequency reference is set below the frequency set in E1-09 (Minimum Output Frequency), the Inverter will not operate. Raise the frequency reference to at least the minimum output frequency. There is a multi-function analog input setting error. If multi-function analog input H3-09 is set to 1 (frequency gain), and if no voltage (current) is input, then the frequency reference will be zero. Check to be sure that the set value and analog input value are correct. The motor does not operate when an external operation signal is input. The following causes are possible. The Inverter is not in drive mode. If the Inverter is not in drive mode and the DRIVE indicator on the Digital Operator (JVOP-161) does not light up, the Inverter will remain in ready status and will not start. Press the MENU Key to make the DRIVE indicator flash, and enter the drive mode by pressing the DATA/ENTER Key. “-Rdy-” will be displayed when drive mode is entered. 7-26 Troubleshooting The operation method selection is wrong. If constant b1-02 (reference selection) is set to 0 (Digital Operator), the motor will not operate when an external operation signal is input. Set b1-02 to 1 (control circuit terminal) and try again. Similarly, the motor will also not operate if the LOCAL/REMOTE Key has been pressed to switch to Digital Operator operation. In that case press the LOCAL/REMOTE Key* again to return to the original setting. The LOCAL/REMOTE Key is enabled by setting o2-01 to 1 and disabled by setting o2-01 to 2. It is enabled when the drive mode is entered. INFO A 3-wire sequence is in effect. The input method for a 3-wire sequence is different than when operating by forward/stop and reverse/stop (2wire sequence). When 3-wire sequence is set, the motor will not operate even when an input terminal suitable for forward run/stop and reverse run/stop is turned ON. When using a 3-wire sequence, refer to the timing chart and input the proper signals. When using a 2-wire sequence, set the multi-function input terminal (H1-01 through H1-10, terminals S3 to S11) to a value other than 0. The frequency reference is too low. If the frequency reference is set below the frequency set in E1-09 (Minimum Output Frequency), the Inverter will not operate. Raise the frequency reference to at least the minimum output frequency. There is a multi-function analog input setting error. If multi-function analog inputs H3-05 (Multi-function Analog Input Terminal A3 Selection) and H3-09 (Multi-function Analog Input Terminal A2 Selection) are set to 1 (frequency gain), and if no voltage (current) is input, then the frequency reference will be zero. Check to be sure that the set value and analog input value are correct. The Inverter does not operate. When the motor does not operate, and there is no fault or alarm indication, check the items listed below to find the cause and take corrective action. Table 7.7 Troubleshooting when Motor Does Not Operate Probable Causes Descriptions Corrective Actions Run command is not sent. If the indicator on the RUN Key is not lit, Inverter does not operate if a Run command the Run Command is not sent. Input the is not sent. Run Command. The operation method selection is wrong. b1-02 has to be set according to the Run Command input method to be used. b1-02= 0: Digital Operator 1: Control circuit terminal (factory setting) 2: MEMOBUS communications 3: Option board 4: Pulse train input The frequency reference is too low. If the indicator on the STOP Key is flashThe frequency reference has to be set above ing, check the frequency reference monithe frequency set in E1-09 (Minimum Out- tor (U1-01) and set the frequency put Frequency). reference above the frequency set in E109. Set b1-02 according to the Run Command input method to be used. 7-27 Table 7.7 Troubleshooting when Motor Does Not Operate (Continued) Probable Causes The frequency reference selection is wrong. The MENU Key was pressed. The ESC Key was pressed twice. The LOCAL/REMOTE Key was pressed. The STOP Key was pressed. Descriptions Corrective Actions b1-01 has to be set according to the frequency reference input method to be used. b1-01= 0: Digital Operator 1: Control circuit terminal (factory setting) 2: MEMOBUS communications 3: Option board 4: Pulse train input Set b1-01 according to the frequency reference input method to be used. • Press the DATA/ENTER Key. If the MENU Key is pressed once or the • Try turning the power supply off and on ESC Key is pressed twice, the Inverter will again. exit the drive mode and will not operate. If • Set b8-01 (Run Command selection in the MENU Key is pressed during operation, programming modes) to 1(Cannot operthe Inverter will not start even if the Run ate) to remain in the drive mode and Command is sent at the next operation. continue operation even if the MENU Key or ESC Key is pressed. If the LOCAL/REMOTE Key is pressed while the Inverter is stopped, the Inverter will switch to Digital Operator operation and cannot be operated with the external input terminals. • Press the LOCAL/REMOTE Key. • Try turning the power supply off and on again. • Set o2-01 (LOCAL/REMOTE Key enable/disable) to 0 (Disabled) to disable the LOCAL/REMOTE Key. If the STOP Key is pressed during operation, the Inverter will decelerate to a stop. • Turn the Run Command off and then on again. • Set o2-02 (STOP key during control circuit terminal operation) to 0 (Disabled) to disable the STOP Key. Wrong selection of a 2-wire If 0 is set to one of H1-01 to H1-10, a 3or a 3-wire sequence. wire sequence is set. Make sure that H1-01 to H1-10 are set to a value other than 0 to use a 2-wire sequence. “Reverse run prohibited” is selected. If b1-04 (Prohibition of reverse operation) is set to 1 (Reverse disabled), the motor will Check the setting of b1-04. not start if the Reverse Run Command is sent. Autotuning has just been completed. The Inverter remains in the autotuning mode right after autotuning has been completed and cannot be operated even if the Run Command is sent. Press the MENU Key to display the drive mode on the Digital Operator and press the DATA/ENTER Key to enter the drive mode. The motor stops during acceleration or when a load is connected. The load may be too heavy. The Inverter has a stall prevention function and an automatic torque boost function, but the motor responsiveness limit may be exceeded if acceleration is too rapid or if the load is too heavy. Lengthen the acceleration time or reduce the load. Also consider increasing the motor capacity. The motor does not accelerate. If the torque limit settings (L7-01 to L7-04) or the torque reference input (torque control) are too small, the motor may not be able to accelerate. Check the settings and input values. Also, for operation with open-loop vector 2 control, refer to Corrective Actions for Control Faults (CF) on page 7-14. 7-28 Troubleshooting The motor only rotates in one direction. “Reverse run prohibited” is selected. If b1-04 (Prohibition of Reverse Operation) is set to 1 (reverse run prohibited), the Inverter will not receive Reverse Run Commands. To use both forward and reverse operation, set b1-04 to 0. If the Direction of the Motor Rotation is Reversed If the motor operates in the wrong direction, the motor output wiring is faulty. When the Inverter T1 (U), T2 (V), and T3 (W) are properly connected to the motor T1 (U), T2 (V), and T3 (W), the motor operates in a forward direction when a Forward Run Command is executed. The forward direction depends on the manufacturer and the motor type, so be sure to check the specifications. The direction of rotation can be reversed by switching two wires among T1 (U), T2 (V), and T3 (W). If the Motor Does Not Put Out Torque or If Acceleration is Slow Use the following information if the motor does not output torque or if acceleration is too slow. The torque limit has been reached. When a torque limit has been set in constants L7-01 to L7-04, no torque will be output beyond that limit. This can cause the torque to be insufficient, or the acceleration time to be too long. Check to be sure that the value set for the torque limit is suitable. If torque limits have been set for the multi-function analog input (H3-05 or H3-09 = 10 to 12 or 15), check to be sure that the analog input value is suitable. The stall prevention level during acceleration is too low. If the value set for L3-02 (Stall Prevention Level during Acceleration) is too low, the acceleration time will be too long. Check to be sure that the set value is suitable. The stall prevention level during running is too low. If the value set for L3-06 (Stall Prevention Level during Running) is too low, the speed will drop before outputting torque. Check to be sure that the set value is suitable. Autotuning has not been performed for vector control Vector control will not perform if autotuning has not been performed. Perform autotuning separately for the motor, or set the motor constants through calculations. Alternatively, change the Control Method Selection (A1-02) to V/f control (0 or 1). If the Motor Operates Higher Than the Reference Use the following information if the motor operates higher than the reference. 7-29 The analog frequency reference bias setting is wrong (the gain setting is wrong). The frequency reference bias set in constant H3-03 is added to the frequency reference. Check to be sure that the set value is suitable. A signal is being input to the frequency reference (current) terminal A2 or A3. When 0 (Add to terminal A1) is set for constant H3-09 (Multi-function Analog Input Terminal A2 Function Selection) or H3-05 (Multi-function Analog Input Terminal A3 Function Selection), a frequency corresponding to the terminal A2 or A3 input voltage (current) is added to the frequency reference. Check to be sure that the set value and analog input value are suitable. If the Slip Compensation Function Has Low Speed Precision If speed control accuracy is low for the slip compensation function, the slip compensation limit has been reached. With the slip compensation function, compensation cannot be carried out beyond the slip compensation limit set in constant C3-03. Check to be sure that the set value is suitable. If There is Low Speed Control Accuracy at High-speed Rotation in Openloop Vector Control Method The motor's rated voltage is high. The Inverter's maximum output voltage is determined by its input voltage. (For example, if 200 VAC is input, then the maximum output voltage will be 200 VAC.) If, as a result of vector control, the output voltage reference value exceeds the Inverter output voltage maximum value, the speed control accuracy will decrease. Use a motor with a low rated voltage (i.e., a special motor for use with vector control), or change to flux vector control. If Motor Deceleration is Slow Use the following information when the motor deceleration is slow. The deceleration time is long even when braking resistor is connected. The following causes are possible. “Stall prevention during deceleration enabled” is set. When braking resistor is connected, set constant L3-04 (Stall Prevention Selection during Deceleration) to 0 (disabled) or 3 (with braking resistor). When this constant is set to 1 (enabled, the factory setting), braking resistor does not fully function. The deceleration time setting is too long. Check the deceleration time setting (constants C1-02, C1-04, C1-06, and C1-08). Motor torque is insufficient. If the constants are correct and there is no overvoltage fault, then the motor's power is limited. Consider increasing the motor capacity. 7-30 Troubleshooting The torque limit has been reached. When a torque limit has been set in constants L7-01 to L7-04, no torque will be output beyond that limit. This can cause the deceleration time to be too long. Check to be sure that the value set for the torque limit is suitable. If H3-09 (Multi-function Analog Input Terminal A2 Function Selection) or H3-05 (Multi-function Analog Input Terminal A3 Function Selection) is set to 10, 11, 12 or 15 (positive and negative torque limit), check to be sure that the analog input value is suitable. If the Vertical-axis Load Drops When Brake is Applied The sequence is incorrect. The Inverter goes into DC injection braking status for 0.5 seconds after deceleration is completed. (This is the factory-set default.) To ensure that the brake holds, set frequency detection 2 (H2-01 = 5) for the multi-function contact output terminals (M1 and Mw) so that the contacts will turn OFF when the output frequency is greater than L4-01 (3.0 to 5.0 Hz). (The contacts will turn ON below L4-01.) There is hysteresis in frequency detection 2 (i.e., a frequency detection width, L4-02 = 2.0 Hz). Change the setting to approximately 0.5 Hz if there are drops during stop. Do not use the multi-function contact output run signal (H2-01 = 0) for the brake ON/OFF signal. If the Motor Overheats Take the following steps if the motor overheats. The load is too big. If the motor load is too heavy and the motor is used with the effective torque exceeding the motor's rated torque, the motor will overheat. Some motor rating are given for short period performance and are not continuous ratings. Reduce the load amount by either lightening the load or lengthening the acceleration/deceleration time. Also consider increasing the motor capacity. The ambient temperature is too high. The motor rating is determined within a particular ambient operating temperature range. The motor will burn out if it is run continuously at the rated torque in an environment in which the maximum ambient operating temperature is exceeded. Lower the motor's ambient temperature to within the acceptable ambient operating temperature range. The withstand voltage between the motor phases is insufficient. When the motor is connected to the Inverter output, a surge is generated between the Inverter switching and the motor coil. Normally the maximum surge voltage is three times the Inverter's input power supply voltage (i.e., 1,200 V for 400 V Class). Be sure to use a motor with a withstand voltage between the motor phases that is greater than the maximum surge voltage. In particular, when using a 400 V Class Inverter, use a special motor for Inverters. Autotuning has not been performed for vector control Vector control will not perform if autotuning has not been performed. Perform autotuning, or set the motor constants through calculations. Alternatively, change the Control Method Selection (A1-02) to V/f control (0 or 1). 7-31 If There is Noise When the Inverter is Started or From an AM Radio If noise is generated by Inverter switching, implement the following countermeasures: • Change the Inverter's Carrier Frequency Selection (C6-02) to lower the carrier frequency. This will help to some extent by reducing the amount of internal switching. • Install an Input Noise Filter at the Inverter's power supply input area. • Install an Output Noise Filter at the Inverter's power supply output area. • Use metal tubing. Electric waves can be shielded by metal, so encase the Inverter with metal (steel). • Ground the Inverter and motor. • Separate main circuit wiring from control wiring. If the Ground Fault Interrupter Operates When the Inverter is Run The Inverter performs internal switching, so there is a certain amount of leakage current. This may cause the ground fault interrupter to operate and cut off the power supply. Change to a ground fault interrupter with a high leakage detection level (i.e., a sensitivity current of 200 mA or greater per Unit, with an operating time of 0.1 s or more), or one that incorporates high frequency countermeasures (i.e., one designed for use with Inverters). It will also help to some extent to change the Inverter's Carrier Frequency Selection (C6-02) to lower the carrier frequency. In addition, remember that the leakage current increases as the cable is lengthened. If There is Mechanical Oscillation Use the following information when there is mechanical oscillation. The machinery is making unusual sounds. The following causes are possible. There may be resonance between the mechanical system's characteristic frequency and the carrier frequency. If the motor is running with no problems and the machinery is oscillating with a high-pitched whine, it may indicate that this is occurring. To prevent this type of resonance, adjust the carrier frequency with constants C6-02 to C6-05. There may be resonance between a machine's characteristic frequency and the output frequency of the Inverter. To prevent this from occurring, either use the jump frequency functions in constants d3-01 to d3-04 or install rubber padding on the motor base to reduce oscillation. Oscillation and hunting are occurring with open-loop vector 1 control. The gain adjustment may be insufficient. Reset the gain to a more effective level by adjusting constants C4-02 (torque compensation time constant), C2-01 (S-curve Characteristic Time at Acceleration Start), and C3-02 (Slip Compensation Primary Delay Time) in order. Lower the gain setting and raise the primary delay time setting. 7-32 Troubleshooting Vector control will not perform if autotuning has not been performed. Perform autotuning separately for the motor, or set the motor constants through calculations. Alternatively, change the control method selection (A102) to V/f control (0 or 1). Oscillation and hunting are occurring with V/f control. The gain adjustment may be insufficient. Reset the gain to a more effective level by adjusting constants C4-02 (Torque Compensation Primary Delay Time Constant), N1-02 (Hunting Prevention Gain), and C3-02 (Slip Compensation Primary Delay Time) in order. Lower the gain setting and raise the primary delay time setting. Oscillation and hunting are occurring with V/f w/PG control. The gain adjustment may be insufficient. Adjust the various types of speed control loop (ASR) gain. If the oscillation cannot be eliminated in this way, set the hunting prevention selection (constant N1-01) to 0 (disabled) and then try adjusting the gain again. Oscillation and hunting are occurring with open-loop vector 2 control. Adjust the control constants with reference to Adjusted User Constants on page 18 in Chapter 4 Trial Operation. If autotuning has not been performed, or the control method has been changed since last performing autotuning, perform autotuning. If the problem occurs after performing stationary autotuning, perform rotational autotuning. If oscillation and hunting occur under the following special conditions, perform the adjustments described here. Low-speed regenerative load (PRG: 102 only) • If oscillation occurs during low-speed regeneration, increase the setting of N4-30 (low-speed regeneration stability coefficient 2). Increase the setting in intervals of approximately 0.2. The larger the setting, the greater the ratio of the speed increase relative to the regenerative load will be. Operating frequency between 6 and 10 Hz (PRG: 102 only) • Accelerate the motor gradually, set N4-32 (speed estimator gain fluctuation frequency 1) to the lowest speed at which oscillation occurs and set N4-33 (speed estimator gain fluctuation frequency 2) to the highest. Then, reduce the setting of N4-34 (speed estimator gain fluctuation rate) until the oscillation stops. Adjust N4-34 in intervals of approximately 5% in the range 50% to 100%. Oscillation and hunting are occurring with flux vector control. The gain adjustment is insufficient. Adjust the various gains for speed control (ASR). If the oscillation points overlap with those of the machine and cannot be eliminated, increase the primary delay time constant for speed control (ASR) in C5-06 and then readjust the gains. If autotuning is not performed, proper performance cannot be achieved for vector control. Perform autotuning or set the motor constants according to calculations. Oscillation and hunting are occurring with PID control. If there is oscillation or hunting during PID control, check the oscillation cycle and individually adjust P, I, and D constants. (Refer to page 6-110.) 7-33 Autotuning has not been performed with vector control. Vector control will not perform if autotuning has not been performed. Perform autotuning separately for the motor, or set the motor constants through calculations. Alternatively, change the Control Method Selection (A1-02) to V/f control. If the Torque Generated for the Motor is Insufficient (Insufficient Power) If autotuning has not been performed, or the control method has been changed since last performing autotuning, perform autotuning. If the problem occurs after performing stationary autotuning, perform rotational autotuning. The torque is insufficient with open-loop vector 2 control (insufficient power). In particular, if there is insufficient power at low speeds, make adjustments using the following methods. Low-speed Electromotive Load (PRG: 102 only) Increase the setting of N4-29 (torque adjustment gain 2). Increase the setting in intervals of approximately 0.05. If the setting is too high, it may have the opposite effect and so do not change the setting by a large amount. Low-speed Regenerative Load (PRG: 102 only) Increase the setting of N4-15 (low-speed regeneration stability coefficient 1). Increase the setting in intervals of approximately 0.1. If the setting is too large, the torque reference monitor and the actual torque accuracy may deteriorate and so do not change the setting by a large amount. If the Torque Reference (U1-09) at Low Speeds in Open-loop Vector 2 Control is Large Compared to That at Medium and High Speeds If the torque reference (U1-09) at low speeds is large compared to that at medium and high speeds for the same load conditions, make adjustments in the way described below. • Reduce the setting for N4-17 (torque adjustment gain). • If the problem still occurs after making the above adjustment, linearize the V/f characteristics. This means making the ratios E1-10/E1-09 and E1-08/E1-07 closer to the ratio E1-13/E1-06. Linearizing the V/f characteristics will, however, reduce the power and so check that the power is sufficient after changing the settings. Do not change the settings more than necessary. If Shock Occurs Near the Speed Estimator Switching Frequency in Openloop Vector 2 Control (PRG: 102 only) The switching frequency refers to the frequency range near the N4-11 setting during acceleration and near the N4-28 setting during deceleration. In open-loop vector 2 control, two speed estimators are switched between and there may be instances of shock occurring at the switchover. If switching shock is a problem, make the adjustments described below. • If shock occurs during acceleration: • Increase the acceleration time within the allowable range. Alternatively, reduce the torque limit. 7-34 Troubleshooting • Reduce the setting for N4-11 to a value less than the factory setting. Reduce the setting in intervals of approximately 5 Hz. • If shock occurs during deceleration: • Increase the deceleration time within the allowable range. Alternatively, reduce the torque limit. • Reduce the setting for N4-28 to a value less than the factory setting. Reduce the setting in intervals of approximately 5 Hz. The factory settings for N4-11 (speed estimator switching frequency) and N4-28 (speed estimator switching frequency 2) are 70 Hz and 50 Hz respectively. If the problem still occurs after making the above adjustments, use open-loop vector 1 control (A1-02 = 2). If Torque Ripple Occurs at Very Low Speeds in Open-loop Vector 2 Control (PRG: 102 only) Either increase the operating frequency or use open-loop vector 1 control (A1-02 = 2). If the Motor Rotates Even When Inverter Output is Stopped If the motor rotates even when the Inverter output is stopped, the DC injection braking is insufficient. If the motor continues operating at low speed, without completely stopping, and after a deceleration stop has been executed, it means that the DC injection braking is not decelerating enough. Adjust the DC injection braking as follows: • Increase the constant b2-02 (DC Injection Braking Current) setting. • Increase the constant b2-04 (DC Injection Braking (initial excitation) Time at Stop) setting. If OV is Detected When the Fan is Started, or Fan Stalls Generation of OV (main circuit voltage) and stalling can occur if the fan is turning when it is started. The DC injection braking is insufficient when starting. This can be prevented by slowing fan rotation by DC injection braking before starting the fan. Increase the constant b2-03 (DC injection braking time (initial excitation) at start) setting. If Output Frequency Does Not Rise to Frequency Reference Use the following information if the output frequency does not rise to the frequency reference. The frequency reference is within the jump frequency range. When the jump frequency function is used, the output frequency does not change within the jump frequency range. Check to be sure that the Jump Frequency (constants d3-01 to d3-03) and Jump Frequency Width (constant d3-04) settings are suitable. 7-35 The frequency reference upper limit has been reached. The output frequency upper limit is determined by the following formula: Maximum Output Frequency (E1-04) × Frequency Reference Upper Limit (d2-01) / 100 Check to be sure that the constant E1-04 and d2-01 settings are suitable. Acoustic Noise From the Motor The carrier frequency is automatically reduced if a current exceeding 110% of the Inverter rated current flows while the Inverter output frequency is low. When the carrier frequency is reduced, acoustic noise form the motor will change. If acoustic noise from the motor causes a problem, change L8-38 (Carrier frequency reduction selection) to 0 (Disabled). However, for mechanical loads that require repetitive high torque, such as with cranes, leave L838 to 1 (Enabled) without changing. Acoustic noise from the motor can be changed by changing the setting of L8-39 (Reduced carrier frequency). (The minimum set value is 1.0 kHz for open-loop vector control.) 7-36 8 Maintenance and Inspection This chapter describes basic maintenance and inspection for the Inverter. Maintenance and Inspection........................................8-2 Maintenance and Inspection Outline of Warranty The warranty period of the Inverter is as follows: Warranty Period: This product is warranted for twelve months after being delivered to Yaskawa's customer or if applicable eighteen months from the date of shipment from Yaskawa's factory whichever comes first. Daily Inspection Check the following items with the system in operation. • The motor should not be vibrating or making unusual noises. • There should be no abnormal heat generation. • The ambient temperature should not be too high. • The output current value shown on the monitor displays should not be higher than normal. • The cooling fan on the bottom of the Inverter should be operating normally. Periodic Inspection Check the following items during periodic maintenance. Always turn OFF the power supply before beginning inspection. Confirm that the LCD and LED indicators on the front cover have all turned OFF, and then wait until at least five minutes has elapsed before beginning the inspection. Be sure not to touch terminals right after the power has been turned off. Doing so can result in electric shock. Table 8.1 Periodic Inspections Item Inspection External terminals, Are all screws and bolts tight? mounting bolts, connecAre connectors tight? tors, etc. Tighten loose screws and bolts firmly. Reconnect the loose connectors. Are the fins dirty or dusty? Clean off any dirt and dust with an air gun using dry air at a pressure of 39.2 x 104 to 58.8 x 104 Pa (4 to 6 kg•cm2). PCBs Is there any conductive dirt or oil mist on the PCBs? Clean off any dirt and dust with an air gun using dry air at a pressure of 39.2 x 104 to 58.8 x 104 Pa (4 to 6 kg•cm2). Replace the boards if they cannot be made clean. Cooling fan Is there any abnormal noise or vibration or has the total operating time exceeded Replace the cooling fan. 20,000 hours? Power elements Is there any conductive dirt or oil mist on the elements? Clean off any dirt and dust with an air gun using dry air at a pressure of 39.2 x 104 to 58.8 x 104 Pa (4 to 6 kg•cm2). Smoothing capacitor Are there any irregularities, such as discoloration or odor? Replace the capacitor or Inverter. Heatsinks 8-2 Corrective Procedure Maintenance and Inspection Periodic Maintenance of Parts The Inverter is configured of many parts, and these parts must be operating properly in order to make full use of the Inverter functions. Among the electronic components, there are some that require maintenance depending on their usage conditions. In order to keep the Inverter operating normally over a long period of time, it is necessary to perform period inspections and replace parts according to their service life. Periodic inspection standards vary depending the Inverter's installation environment and usage conditions. The Inverter's maintenance periods are noted below. Keep them as reference. Refer to Cooling Fan Replacement Outline (Page 8-6) for replacing a cooling fan and Circulation Fan Replacement Outline (Page 8-16) for replacing a circulation fan. To replace other parts, contact your Yaskawa representative or YASKAWA ELECTRIC ENGINEERING CORPORATION for details on preventive maintenance for Inverters. Table 8.2 Part Replacement Guidelines Part Cooling fan Smoothing capacitor Breaker relays Standard Replacement Period 2 to 3 years 5 years - Replacement Method Replace with new part. Replace with new part. (Determine need by inspection.) Determine need by inspection. Fuses 10 years Replace with new part. Aluminum capacitors on PCBs 5 years Replace with new board. (Determine need by inspection.) Note The standard replacement period is based on the following usage conditions: Ambient temperature:Yearly average of 30°C Load factor: 80% max. Operating rate: 12 hours max. per day Procedure for Adjusting Constants after Replacement of Control Board Perform the following operations before adjusting the constants. • For 400-V class Inverters of 55 kW to 300 kW with SPEC: E or later, take safety measures such as the installation of an emergency-stop switch. Failure to do so may result in injury caused by the motor accidentally rotating during stationary autotuning performed by the Inverter when the constants are adjusted. • Before replacing the control board, first use the COPY function of the Digital Operator to copy the settings of the constants of board from the Inverter to the Digital Operator. When using the copy function of the Digital Operator, check that the following settings are the same between the Inverter and the Digital Operator. Note the setting of A1-02 (Control method selection). • Inverter product and type • Software number • Inverter capacity and voltage • Control method After replacing the board, use the following procedure to adjust the constants. Steps 4 and 5 are not required for 400-V class Inverters of 0.4 kW to 45 kW, 400-V class Inverters of 55 kW to 300 kW with SPEC: A to C, and all models of 200-V class Inverters regardless of capacity. If using a 400-V class Inverter of 55 kW to 300 kW with SPEC: E or later, use a control board, version ETC618046-S1033 or later, and then perform steps 4 and 5. Contact your Yaskawa representative if a motor cannot be connected, the motor being used is two frames smaller than the Inverter, or a control board with older version is used. 8-3 Step No. Digital Operator Display Description -ADV- Inverter Model # 1 o2-04=2F Set o2-04 (kVA selection) to the capacity of the Inverter that you use. 4055 "0" -ADV- 2 Initialization A1-02=2 *2* Open Loop Vector -ADV- Init Parameters 3 A1-03=2220 *0* 2 WIRE Initial "0" -DRIVE- Mtr Rated Power 4 T1-02=55.00kW (2.00 650.00) "55.00kW" -DRIVE- Shipping Adjust 5 0Hz/ 0.0A Tuning Ready ? Press Run Key 6 - Set A1-02 to the control method to be used. The value of the control method should be set to the same value as when the constants were copied from the Inverter to the Digital Operator. Set A1-03 (Initialize) to 2220 (2-wire initialization) or 3330 (3-wire initialization). This example is a typical setting for initialization by a 2-wire sequence. If the mode is switched to the DRIVE after initialization has been completed, the motor power setting display appears. Set T1-02 (Motor output power) to the motor capacity of the connected motor. This example is the setting for a 55 kW motor. Press the Increment Key to view the shipping adjustment display. After confirming that the motor has been connected, press the RUN Key to start autotuning. Note: Do not touch the motor terminals. Although the motor does not rotate, voltage is being supplied to the motor though the motor is not rotating. After autotuning has been completed, use the copy function of the Operator to copy the settings of the constants of the control board from the Operator to the Inverter before replacing the board. If the copy function is not available, change the setting of the constants manually. -DRIVE- Frequency Ref 7 U1-01=0.00Hz U1-02= 0.00Hz U1-03= 0.0A If the mode is switched to the DRIVE, the frequency setting display appears, and the operation becomes enabled. Procedure for Changing Constants through Communications For 400-V class Inverters of 55 kW to 300 kW with SPEC: E or later, take safety measures such as the installation of an emergency-stop switch before adjusting constants. Failure to do so may result in injury caused by the motor accidentally rotating during stationary autotuning performed by the Inverter when the constants are adjusted. After replacing the control board, write in all of the constants to the new board with MEMOBUS communications or a Communications Option Board. Next, be sure to perform autotuning to make adjustments after shipping. Step No. Digital Operator Display Description -A.TUNE- Tuning Mode Sel 1 T1-01=3 Set T1-01 (Autotuning mode selection) to 3 (Shipping adjustment). Shipping Ajust "2" -DRIVE- Mtr Rated Power 2 T1-02=55.00kW (3.00 650.00) "55.00kW" Press the Increment Key to view the motor rated power display. Set T1-02 (Motor output power) to the capacity of the connected motor. -DRIVE- Rated Current 3 T1-04=95.0A (16.5㨪330.0) "95.0A" -DRIVE- Shipping Adjust 4 0Hz/ 0.0A Tuning Ready ? Press RUN Key 8-4 Press the Increment Key to view the motor rated current display. Set T1-04 (Motor rated current) to the value of motor rated current. Press the Increment Key to view the shipping adjustment display. After confirming that the motor has been connected, press the RUN Key to start autotuning. Note: Do not touch the motor terminals. Although the motor does not rotate, voltage is being supplied to the motor though the motor is not rotating. Maintenance and Inspection Types and Number of Cooling Fans Used in the Drive Cooling fans used for the Drive has two types; Heatsink cooling fan and heatsink circulation fan. Heatsink cooling fan blows air to the Drive cooling fin. Heatsink circulation fan stirs up the air inside the Drive unit. Table 8.3 shows the number of cooling fans used in the Drive. For more information on models and specifications of cooling fans, contact your Yaskawa representative or YASKAWA ELECTRIC ENGINEERING CORPORATION. When replacing the fan, use the specified type of the fan. If the inapplicable fans are used, performance of the Drive will not be fully obtained. Table 8.3 Number of Cooling Fans to be Used Maximum Motor Capacity (kW) 200 V Class Heatsink Cooling Heatsink Circulation Fan Fan 400 V Class Heatsink Cooling Heatsink Circulation Fan Fan 0.4 - - - - 0.75 - - - - 1.5 - - 1 - 2.2 1 - 1 - 3.7 1 - 1 - 1 - 4.0 - 5.5 2 - 2 1 7.5 2 1 2 1 11 2 - 2 1 15 2 1 2 1 18.5 2 - 2 - 22 2 - 2 - 30 2 1 2 - 37 2 1 2 - 45 2 1 2 - 55 2 1 2 1 75 2 1 2 1 90 2 1 2 1 110 2 1 2 1 132 2 1 160 2 1 4 2 220 4 2 300 5 2 185 - 8-5 Cooling Fan Replacement Outline 200 V and 400 V Class Inverters of 15 kW or Less A cooling fan is attached to the bottom of the Inverter. If the Inverter is installed using the mounting holes on the back of the Inverter, the cooling fan can be replaced without removing the Inverter from the installation panel. Removing the Cooling Fan 1. Press in on the right and left sides of the fan cover in the direction of arrows 1 and pull the fan out in the direction of arrow 2. 2. Pull out the cable connected to the fan from the fan cover and disconnect the relay connector. 3. Open the fan cover on the left and right sides and remove the fan cover from the fan. Mounting the Cooling Fan 1. Attach the fan cover to the cooling fan. Be sure that the airflow direction indicated by the arrows above faces into the Inverter. 2. Connect the relay connector securely and place the relay connector and cable into the fan cover. 3. Mount the fan cover on the Inverter. Be sure that the tabs on the sides of the fan cover click into place on the Inverter. 1 Airflow direction 2 1 Fan cover Fig 8.1 Cooling Fan Replacement (200 V Class Inverters of 3.7 kW) 8-6 Maintenance and Inspection 200 V and 400 V Class Inverters of 18.5 kW or More A cooling fan is attached to the top panel inside the Inverter. The cooling fan can be replaced without removing the Inverter from the installation panel. 200 V Class Inverters of 18.5 kW Removing the Cooling Fan 1. Remove the terminal cover, Inverter cover, Digital Operator, and front cover from the front of the Inverter. 2. Remove the control board bracket to which the boards are mounted. Remove all cables connected to the controller. The cables connected to the control circuit terminals can be removed at the same time by removing them together with the control circuit terminal board. (Refer to page 8-21) 3. Remove the cooling fan power cable connector (CN26 and CN27) from the gate drive board positioned at the back of the control board. 4. Remove the fan cover screws and pull out the fan cover from the Inverter. 5. Remove the cooling fan from the fan cover and replace it with a new one. Mounting the Cooling Fan After attaching a new cooling fan, reverse the above procedure to attach all of the components. When attaching the cooling fan to the mounting bracket, be sure that the airflow faces the top of the Inverter. Airflow direction Control board bracket Fan cover Control board Connector Gate drive board Fig 8.2 Cooling Fan Replacement (200 V Class Inverters of 18.5 kW) 8-7 200 V Class Inverters of 22 kW, 45 kW, 55 kW and 400 V Class Inverters of 18.5 kW to 75 kW Removing the Cooling Fan 1. Remove the terminal cover, Inverter cover, Digital Operator, and front cover from the front of the Inverter. 2. Pull the cooling fan power cable connector that extends from the fan cover cable hole out of the cooling fan power relay board. 3. Remove the fan cover screws and pull out the fan cover from the Inverter. 4. Remove the cooling fan from the fan cover and replace it with a new one. Mounting the Cooling Fan After attaching a new cooling fan, reverse the above procedure to attach all of the components. Refer to the next page for attaching the fan cover. When attaching the cooling fan to the mounting bracket, be sure that the airflow faces the top of the Inverter. Front cover mounting screws Front cover Terminal cover Terminal cover mounting screws Circulation fan mounting screws Fan cable pullout position Circulation fan Airflow direction Fan support mounting screws Fan support Fan support Airflow direction Cooling fans Fan power relay board Cooling fans Cooling fan mounting screws Cooling fan mounting screws Fan power cable pullout position Fig 8.3 Cooling Fan Replacement (200 V Class Inverters of 45 kW and 55 kW) 8-8 Maintenance and Inspection Attaching the Fan Cover 1. Tilt the fan cover toward the bottom of the Inverter as shown in Fig 8.4 and insert it to the mounting hole until it meets with A. Fan cover A Bottom Inverter Cooling fan Top Inverter Fig 8.4 2. Push the fan cover toward the top of the Inverter. Fig 8.5 3. Make sure that there is no gap between the fan cover and A. Then screw it in place with the three screws. Make sure that there is no gap. NG A A Fig 8.6 8-9 200 V Class Inverters of 30 kW and 37 kW Removing the Cooling Fan 1. Remove the terminal cover, Inverter cover, Digital Operator, and front cover from the front of the Inverter. 2. Remove the panel to which the control board, the gate drive board, and the cooling fan power relay board are mounted. Remove any cables that are connected to the control board, the gate drive board, and the cooling fan power relay board. The cable that is connected to the control circuit terminals can be removed together with the control circuit terminal board. (Refer to page 8-21) 3. Remove the fan cover screws and pull out the fan cover from the Inverter. 4. Remove the cooling fan from the fan cover and replace it with a new one. Mounting the Cooling Fan After attaching a new cooling fan, reverse the above procedure to attach all of the components. When attaching the cooling fan to the mounting bracket, be sure that the airflow faces the top of the Inverter. Fan support mounting screws Fan cover Panel mounting screws Front cover mounting screws Cooling fan power relay board Gate drive board Front cover Panel mounting screws Capacitor Terminal cover Terminal cover mounting screws Terminal board Circulation fan mounting screws Pay attention to the protruding part of the fan cable. Circulation fan Cooling fans Airflow direction Fan cover Cooling fan mounting screws Fig 8.7 Cooling Fan Replacement (200 V Class Inverters of 30 kW and 37 kW) 8-10 Maintenance and Inspection 200 V Class Inverters of 75 kW Removing the Cooling Fan 1. Remove the terminal cover, Inverter cover, Digital Operator, and front cover from the front of the Inverter. 2. Remove the panel to which the control board, the gate drive board, and the cooling fan power relay board are mounted. Remove any cables that are connected to the control board, the gate drive board, and the cooling fan power relay board. The cable that is connected to the control circuit terminals can be removed together with the control circuit terminal board. (Refer to page 8-21) 3. Remove the fan cover screws and pull out the fan cover from the Inverter. 4. Remove the cooling fan from the fan cover and replace it with a new one. Mounting the Cooling Fan After attaching a new cooling fan, reverse the above procedure to attach all of the components. When attaching the cooling fan to the mounting bracket, be sure that the airflow faces the top of the Inverter. Front cover mounting screws Front cover Terminal cover Terminal cover mounting screws Fan power relay board Fan cover mounting screws Fan cover Control board mounting panel Circulation fan mounting screws Control board mounting panel Control board mounting panel mounting screws Circulation fan Cooling fan power connector Cooling fan airflow direction (CN26) Fan cover Gate drive board Cooling fan Control circuit terminal board Cooling fan mounting screws Finger guard Cooling fan airflow direction Note: A finger guard is not provided on Inverters with slits. Fig 8.8 Cooling Fan Replacement (200 V Class Inverters of 75 kW) 8-11 400 V Class Inverters of 90 kW and 110 kW Removing the Cooling Fan 1. Remove the terminal cover, Inverter cover, Digital Operator, and front cover from the front of the Inverter. 2. Remove the panel to which the control board, the gate drive board, and the cooling fan power relay board are mounted. Remove any cables that are connected to the control board, the gate drive board, and the cooling fan power relay board. The cable that is connected to the control circuit terminals can be removed together with the control circuit terminal board. (Refer to page 8-21) 3. Remove the fan cover screws and pull out the fan cover from the Inverter. 4. Remove the cooling fan from the fan cover and replace it with a new one. Mounting the Cooling Fan After attaching a new cooling fan, reverse the above procedure to attach all of the components. When attaching the cooling fan to the mounting bracket, be sure that the airflow faces the top of the Inverter. Front cover mounting screws Front cover Terminal cover Terminal cover mounting screws Circulation fan Cooling fan power relay board Fan cover mounting screws Airflow direction Circulation fan mounting screws Circulation fan Circulation fan power connector Cooling fan mounting screws Fig 8.9 Cooling Fan Replacement (400 V Class Inverters of 90 kW and 110 kW) 8-12 Maintenance and Inspection 200 V Class Inverters of 90 kW and 110 kW/400 V Class Inverters of 132 kW and 160 kW Removing the Cooling Fan 1. Remove the terminal cover, Inverter cover, Digital Operator, and front cover from the front of the Inverter. 2. Remove the panel to which the control board, the gate drive board, and the cooling fan power relay board are mounted. Remove any cables that are connected to the control board, the gate drive board, and the cooling fan power relay board. The cable that is connected to the control circuit terminals can be removed together with the control circuit terminal board. (Refer to page 8-21) 3. Remove the fan cover screws and pull out the fan cover from the Inverter. 4. Remove the cooling fan from the fan cover and replace it with a new one. Mounting the Cooling Fan After attaching a new cooling fan, reverse the above procedure to attach all of the components. When attaching the cooling fan to the mounting bracket, be sure that the airflow faces the top of the Inverter. Front cover mounting screws Fan cover Fan cover mounting screws Fan power relay board Gate drive board Front cover Control board Terminal cover Terminal cover mounting screws Circulation fan Circulation fan mounting screws Circulation fan airflow direction Fan cover mounting screws Fan cover Fan cover Fan airflow direction Fan power relay board Fan mounting screws Finger guard*1 Cooling fan Fan ground cable*2 * 1. There is no finger guard mounted to the fan for some capacities. (There is a guard on the Inverter side.) * 2. There is no fan ground cable for the capacities without a finger guard. Fig 8.10 Cooling Fan Replacement (200 V Class Inverters of 90 kW and 110 kW) 8-13 400 V Class Inverters of 185 kW and 220 kW Removing the Cooling Fan 1. Remove the terminal cover and top and bottom front covers from the front of the Inverter. 2. Remove any cables that are connected to the cooling fan power relay board. 3. Remove the fan cover screws and pull out the fan covers from the Inverter. 4. Remove the cooling fan from the fan cover and replace it with a new one. Mounting the Cooling Fan After attaching a new cooling fan, reverse the above procedure to attach all of the components. When attaching the cooling fan to the fan cover, be sure that the airflow faces the top of the Inverter. Make sure that the fan cable and the fan ground cable are not tangled or pinched. Fan cover Front cover mounting screws Fan power relay board Fan cover Top front cover Terminal cover Bottom front cover Terminal cover mounting screws Fan cable Fan ground cable Fan cover mounting screws Enlarged view Fan airflow direction Fan cover mounting screws Colling fan Cooling fan mounting screws Finger guard Fig 8.11 Cooling Fan Replacement (400 V Class Inverters of 185 kW and 220 kW) 8-14 Maintenance and Inspection 400 V Class Inverters of 300 kW Removing the Cooling Fan 1. Remove the terminal cover, Inverter cover, Digital Operator, and front cover from the front of the Inverter. 2. Remove any cables that are connected to the cooling fan power relay board. The cable that is connected to the terminal board can be removed together with the terminal board. 3. Remove the fan unit screws and pull out the fan units from the Inverter. 4. Replace the fan units with new ones. And, remove the screws for the fan power relay board and attach this board to the new unit. Mounting the Cooling Fan After attaching a new cooling fan unit, reverse the above procedure to attach all of the components. Front cover mounting screws Fan power relay board Fan cover Fan cover Top front cover Bottom front cover Terminal cover Terminal cover mounting screws Relay board mounting screws Fan cover mounting screws Fan power relay board Enlarged view Fan cover mounting screws Fan units Fan airflow derection Fig 8.12 Cooling Fan Replacement (400 V Class Inverters of 300 kW) 8-15 Circulation Fan Replacement Outline With some capacities, there is a small fan installed inside the Inverter for the purpose of increasing circulation in areas where heat has built up. These fans have built-in fan sensors that output an alarm when the rotation rate of the fan drops to indicate that replacement is necessary. 200 V Class Inverters of 7.5 kW/400 V Class Inverters of 5.5 kW and 7.5 kW The circulation fan is installed behind the control circuit terminal board inside the Inverter. The circulation fan can be replaced by removing the control circuit terminal board. Removing the Circulation Fan 1. Remove the Digital Operator, the terminal cover, and the front cover. 2. Remove the control circuit terminal board. Remove the cables connected to the terminals if necessary. 3. While pushing the two tabs (A) in direction 1, pull the fan out in direction 2. 4. Remove the relay connector connected to the fan. Mounting the Circulation Fan Reverse the above procedure to mount the fan. Be sure to mount the fan so that the air flows towards the top of the Inverter (direction indicated by the arrow). Mount the fan securely using the tabs (A). Confirm that there are no cables in contact with the fan’s rotating parts. Control Board 2 1 Airflow direction Tabs (A) Circulation fan Inverter with Control Circuit Terminal Board Removed Fig 8.13 Circulation Fan Replacement (200 V Class Inverters of 7.5 kW/400 V Class Inverters of 5.5 kW and 7.5 kW) 8-16 Maintenance and Inspection 200 V Class Inverters of 15 kW/400 V Class Inverters of 11 kW and 15 kW The circulation fan is installed at the top-left corner of the Inverter interior. Removing the Circulation Fan 1. Remove the Digital Operator, the terminal cover, and the front cover. 2. While pushing the relay connector tab (A) in direction 1, pull the relay connector out in direction 2. 3. While pushing the fan tabs (B) in direction 3, pull the fan out in direction 2. 4. Remove the relay connector connected to the fan. Mounting the Circulation Fan Reverse the above procedure to mount the fan. Be sure to mount the fan so that the air flows towards the bottom of the Inverter (direction indicated by the arrow). Mount the fan securely using the fan tabs (B). Confirm that there are no cables in contact with the fan’s rotating parts. 4 Circulation fan 2 1 Relay connector tab (A) Fan tabs (B) 3 Airflow direction Fig 8.14 Circulation Fan Replacement (200 V Class Inverters of 15 kW/400 V Class Inverters of 11 kW and 15 kW) 200 V Class Inverters of 30 kW or More/400 V Class Inverters of 55 kW or More The circulation fan is installed in front of the fan cover inside the Inverter. Remove the circulation fan using the procedure for replacing the cooling fan and replace it with the new fan. (The installation position for 200 V Class Inverters of 75 kW is different.) 200 V Class Inverters of 75 kW The circulation fan is installed behind the control board mounting panel. Do not subject the fan to shock during replacement. Removing the Circulation Fan 1. Remove the terminal cover, the Inverter cover, the Digital Operator, and the control board cover. 8-17 2. Pull out the cables connected to the control circuit terminal board, the gate drive board, and the cooling fan power relay board. 3. Remove the control board mounting panel. 4. Replace the circulation fan installed behind the control board mounting panel. Mounting the Circulation Fan Reverse the above procedure to mount the fan. Be sure to mount the fan so that the air flows in the direction indicated by the arrow in the corresponding diagram. Confirm that there are no cables in contact with the fan’s rotating parts. Refer to Fig 8.8 Cooling Fan Replacement (200 V Class Inverters of 75 kW) for details. 8-18 Maintenance and Inspection 400 V Class Inverters of 185 kW and 220 kW Two circulation fans are installed as described in the following sections. Removing the Circulation Fan 1. Remove the terminal cover and top and bottom front covers. 2. Unscrew the frame fixing screws and take off the frame. 3. Remove the relay connector connected to the fan. 4. Remove the fan cover mounting screws and pull the fan cover out. 5. Remove the fan from the fan cover and replace it with a new one. Mounting the Circulation Fan Reverse the above procedure to mount the fan. Be sure to mount the fan so that the air flows in the direction indicated by the arrow in the corresponding diagram. Confirm that there are no cables in contact with the fan’s rotating parts. Fan cable Fix the fan cable with lnsulok ties Frame fixing screws Frame Fan airflow direction Enlarged view Fan cover mounting screws Circulation fan Fan airflow direction Fan cover mounting screws Enlarged view Fan cable Fig 8.15 Circulation Fan Replacement (400 V Class Inverters of 185 kW and 220 kW) 8-19 400 V Class Inverters of 300 kW Two circulation fans are installed as described in the following sections. Removing the Circulation Fan 1. Remove the terminal cover and top and bottom front covers. 2. Unscrew the frame fixing screws and takeoff the frame. 3. Remove the relay connector connected to the fan. 4. Remove the fan cover mounting screws and pull the fan cover out. 5. Remove the fan from the fan cover and replace it with a new one. Mounting the Circulation Fan Reverse the above procedure to mount the fan. Be sure to mount the fan so that the air flows in the direction indicated by the arrow in the corresponding diagram. Confirm that there are no cables in contact with the fan’s rotating parts. Fan cable Fix the fan cable with Insulok ties Frame Frame fixing screws Fan airflow direction Enlarged view Fan cover mounting screws Circulation fan Fan airflow direction Enlarged view Fix the fan cable with Insulok ties Fan cable Fan cover mounting scerws Fig 8.16 Circulation Fan Replacement (400 V Class Inverters of 300 kW) 8-20 Maintenance and Inspection Removing and Mounting the Control Circuit Terminal Board The control circuit terminal board can be removed and mounted without disconnecting the cables. Always confirm that the charge indicator is not lit before removing or mounting the control circuit terminal board. IMPORTANT Removing the Control Circuit Terminal Board 1. Remove the Digital Operator and front cover. 2. Remove the connecting line connectors connected to FE and NC on the control circuit terminal board. 3. Loosen the mounting screws (1) on the left and right sides of the control terminals until they are free. (It is not necessary to remove these screws completely. They are self-rising.) 4. Pull the terminal board out sideways (in direction 2) with the screws sticking out from the board. Mounting the Control Circuit Terminal Board Reverse the removal procedure to mount the terminal board. Confirm that the control circuit terminal board and the control board properly meet at connector CN5 before pressing in on the board. The connector pins may be bent if the board is forced into place, possibly preventing correct Inverter operation. Removing and Mounting the Control Circuit Terminal Board FE NC Fig 8.17 Removing the Control Circuit Terminal Board 8-21 9 Specifications This chapter describes the basic specifications of the Inverter and specifications for options and peripheral devices. Standard Inverter Specifications .................................. 9-2 Specifications of Options and Peripheral Devices .......9-6 Standard Inverter Specifications The standard Inverter specifications are listed by capacity in the following tables. Specifications by Model Specifications are given by model in the following tables. 200 V Class Table 9.1 200 V Class Inverters Model Number CIMR-G7A Power supply characteristics Output ratings Max. applicable motor output (kW) Rated input current (A) Rated output capacity (kVA) Rated output current (A) 20P4 20P7 21P5 22P2 23P7 25P5 27P5 2011 2015 2018 2022 2030 2037 2045 2055 2075 2090 0.4 0.75 1.5 2.2 3.7 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90 110 3.8 7.2 9.6 14.4 22 32 40 59 79 88 106 143 176 201 246 330 394 457 1.2 2.3 3.0 4.6 6.9 10 13 19 25 30 37 50 61 70 85 110 140 160 3.2 6 8 12 18 27 34 49 66 80 96 130 3-phase; 200, 208, 220, 230, or 240 VAC (Proportional to input voltage.) 160 183 224 300 358 415 Max. output voltage (V) Max. output frequency (Hz) Rated voltage (V) Rated frequency (Hz) Allowable voltage fluctuation Frequencies supported up to 400 Hz using constant setting 3-phase, 200/208/220/230/240 VAC, 50/60 Hz*2 + 10%, - 15% Allowable frequency fluctuation Measures for power supply harmonics DC reactor 12-phase rectification 2110 ±5% Optional Built in Not possible Possible*3 * 1. The maximum applicable motor output is given for a standard 4-pole Yaskawa motor. When selecting the actual motor and Inverter, be sure that the Inverter's rated current is applicable for the motor's rated current. * 2. The voltage of the cooling fan for 200 V Class Inverters of 30 kW is three-phase, 200, 208, or 220 V at 50 Hz or 200, 208, 220, or 230 V at 60 Hz. * 3. A 3-wire transformer is required on the power supply for 12-phase rectification. 9-2 Standard Inverter Specifications 400 V Class Table 9.2 400 V Class Inverters Model Number CIMR-G7A Power supply characteristics Output ratings Max. applicable motor output (kW) *1 Rated input current (A) Rated output capacity (kVA) Rated output current (A) Max. output voltage (V) Max. output frequency (Hz) 0.4 0.75 1.5 2.2 4.1 5.8 3.7 4.7 1.4 2.6 1.8 3.4 41P5 42P2 43P7 45P5 47P5 2.2 3.7 5.5 7.5 7.4 10.8 18 25 6.9 11 16 21 Allowable frequency fluctuation ±5% DC reactor 12-phase rectification Max. output frequency (Hz) Max. voltage (V) Rated frequency (Hz) 11 15 18.5 32 40 46 26 32 34 42 Optional Built in Possible*2 4022 4030 4037 4045 4055 4075 4090 4110 4132 4160 4185 4220 4300 22 30 37 45 55 75 90 110 132 160 185 220 300 57 72 88 107 141 182 215 264 297 332 407 495 666 40 50 61 74 98 130 150 180 210 230 280 340 460 52 65 80 97 128 165 195 240 270 302 370 3-phase, 380, 400, 415, 440, 460, or 480 VAC (Proportional to input voltage.) 450 605 Frequencies supported up to 400 Hz using constant setting 3-phase, 380, 400, 415, 440, 460, or 480 VAC, 50/60 Hz + 10%, - 15% Allowable frequency fluctuation ±5% DC reactor 12-phase rectification 4018 Not possible Allowable voltage fluctuation Measures for power supply harmonics 4015 3-phase, 380, 400, 415, 440, 460 or 480 VAC, 50/60 Hz + 10%, - 15% Model Number CIMR-G7A 4011 4.8 6.2 9 15 21 27 3-phase; 380, 400, 415, 440, 460, or 480 VAC (Proportional to input voltage.) Frequencies supported up to 400 Hz using constant setting Allowable voltage fluctuation Max. applicable motor output (kW)*1 Rated input current (A) Rated output capacity (kVA) Rated output current (A) Max. output voltage (V) Output ratings 40P7 Rated voltage (V) Rated frequency (Hz) Measures for power supply harmonics Power supply characteristics 40P4 Built in Possible*2 * 1. The maximum applicable motor output is given for a standard 4-pole Yaskawa motor. When selecting the actual motor and Inverter, be sure that the Inverter's rated current is applicable for the motor's rated current. * 2. A 3-wire transformer (optional) is required on the power supply for 12-phase rectification. 9-3 Common Specifications The following specifications apply to both 200 V and 400 V Class Inverters. Table 9.3 Common Specifications Model Number CIMR-G7A Specification Sine wave PWM Flux vector control, open-loop vector 1/2 control, V/f control, V/f with PG control (switched by constant setting) Control method 150%/0.3 Hz (Open-loop vector 2 control), 150%/0 min−1 (Flux vector control)*1 Torque characteristics 1:200 (Open-loop vector 2 control), 1:1000 (Flux vector control)*1 Speed control range Speed control accuracy *4 Speed control response Torque limits Torque accuracy Control characteristics Frequency control range Frequency accuracy (temperature characteristics) ±5% 0.01 to 400 Hz*3 Digital references: ± 0.01% (-10°C to +40°C) Analog references: ±0.1% (25°C ±10°C) Digital references: 0.01 Hz, Analog references: 0.03 Hz/60 Hz (11 bit with no sign) Output frequency resolution 0.001 Hz Overload capacity and maximum current*2 150% of rated output current per minute*5 *8 Frequency setting signal -10 to 10 V, 0 to 10 V, 4 to 20 mA, pulse train Acceleration/Deceleration time 0.01 to 6000.0 s (4 selectable combinations of independent acceleration and deceleration settings) Main control functions Approximately 20% (Approximately 125% with Braking Resistor option, braking transformer built into 200 V and 400 V Class Inverters for 15 kW or less.)*2 Restarting for momentary power loss, speed searches, overtorque detection, torque limits, 16-speed control (maximum), acceleration/deceleration time changes, S-curve acceleration/deceleration, 3-wire sequence, autotuning (rotational or stationary), dwell functions, cooling fan ON/OFF control, slip compensation, torque compensation, jump frequencies, upper and lower limits for frequency references, DC braking for starting and stopping, high-slip braking, PID control (with sleep function), energy-saving control, MEMOBUS communications (RS-485/422, 19.2 kbps maximum), fault reset, function copying, droop control (flux vector control only) torque control, speed/torque control switching, etc. Motor protection Protection by electronic thermal overload relay. Instantaneous overcurrent protection Stops at approx. 200% of rated output current. Fuse blown protection Overload protection Protective functions 10 Hz (Open-loop vector 2 control), 30 Hz (Flux vector control) Provided for vector control only (4 quadrant steps can be changed by constant settings.) Frequency setting resolution Braking torque Stops for fuse blown. 150% of rated output current per minute Overvoltage protection 200 Class Inverter: Stops when main-circuit DC voltage is approximately above 410 V. 400 Class Inverter: Stops when main-circuit DC voltage is approximately above 820 V. Undervoltage protection 200 Class Inverter: Stops when main-circuit DC voltage is approximately below 190 V. 400 Class Inverter: Stops when main-circuit DC voltage is approximately below 380 V. Momentary power loss ridethrough *7 Stops for 15 ms or more. With a suitable constant setting, operation can be continued if power is restored within 2 s. Cooling fin overheating Stall prevention Grounding protection*6 Charge indicator Ambient operating temperature Ambient operating humidity Storage temperature Environment ±0.2% (Open-loop vector 2 control, 25°C ± 10°C), ±0.02% (Flux vector control, 25°C ± 10°C) Application site Protection by thermistor. Stall prevention during acceleration, deceleration, or running. Protection by electronic circuits. (Overcurrent level) Lit when the main circuit DC voltage is approx. 50 V or more. -10°C to 40°C (Enclosed wall-mounted type) 10°C to 45°C (Open chassis type) 95% max. (with no condensation) - 20°C to + 60°C (short-term temperature during transportation) Indoor (no corrosive gas, dust, etc.) Altitude 1000 m max. Vibration 200 V Class Inverters of 0.4 to 37 kW and 400 V Class Inverters of 0.4 to 45 kW 10 to 20 Hz: 9.8 m/s2 20 to 55 Hz: 5.9 m/s2 200 V Class Inverters of 45 to 110 kW and 400 V Class Inverters of 55 to 300 kW 10 to 20 Hz: 9.8 m/s2 20 to 55 Hz: 2.0 m/s2 * 1. Rotational autotuning must be performed to ensure obtaining the specifications given for flux or open-loop vector 1/2 control. 9-4 Standard Inverter Specifications * 2. When connecting a Braking Resistor or Braking Resistor Unit, set L3-04 (Stall prevention selection during deceleration) to 0 (disabled). Stopping may not be possible in the specified deceleration time if this function is not disabled. * 3. The maximum output frequency for open-loop vector 2 control is 66 Hz (for PRG: 103, 132 Hz). * 4. The speed control accuracy depends on the installation conditions and type of motor used. Contact your Yaskawa representative for details. * 5. Derating is required for applications that use repetitive loads. (Refer to page 10-6 for details.) * 6. The ground fault here is one which occurs in the motor wiring while the motor is running. A ground fault may not be detected in the following cases. y A ground fault with low resistance which occurs in motor cables or terminals. y A ground fault occurs when the power is turned ON. * 7. Attach a Backup Capacitor Unit for Momentary Power Loss if compensation for power interruptions of up to 2.0 seconds is required for 200 V/400 V Class Inverters with outputs of 0.4 to 7.5 kW. * 8. If running at a speed of 6 Hz or less, the overload protection function can operate even if running within 150% of rated output current per minute. 9-5 Specifications of Options and Peripheral Devices The following options and peripheral devices can be used for the Inverter. Select them according to the application. Table 9.4 Options and Peripheral Devices Purpose Name Protect Inverter wiring MCCB or Ground Fault Interrupter*1 Prevents burning when a Braking Resistor is used. Magnetic Contactor Model (Code) Descriptions NF Always connect a breaker to the power supply line to protect Inverter wiring. Use a ground fault interrupter suitable for high frequencies. SC series Install to prevent the braking resistor from burning out when one is used. Always attach a surge absorber to the coil. Contains switching surge Surge Absorber DCR2- Absorbs surge from the magnetic contactor and control relays. Connect surge absorbers to all magnetic contactors and relays near the Inverter. Isolates I/O signals Isolator DGP Isolates the I/O signals of the Inverter and is effective against inductive noise. Improve the input power factor of the Inverter DC Reactor AC Reactor UZDA- UZBA- Used to improve the input power factor of the Inverter. All Inverters of 18.5 kW or higher contain built-in DC reactors. These are optional for Inverters of 15 kW or less. Install DC and AC reactors for applications with a large power supply capacity (600 kVA or higher). Input Noise Filter LNFD- FN- Reduces noise coming into the Inverter from the power supply line and to reduce noise flowing from the Inverter into the power supply line. Connect as close to the Inverter as possible. Reduce the affects of radio and control device noise Enable stopping the machine in a set time Operates the Inverter externally Finemet zerophase reactor to reduce radio noise*2 Magnetic contactor (MC) AC reactor for power factor improvement Zero phase reactor Braking resistor F11080GB (FIL001097) Reduces noise from the line that sneaks into the Inverter input power system. Insert as close to the Inverter as possible. Can be use on both the input side and output side. Input noise filter F200160BP (300-001-041) Inverter Output Noise Filter LF- Reduces noise generated by the Inverter. Connect as close to the Inverter as possible. Braking Resistor ERF-150WJ (R00) Consumes the regenerative motor energy with a resistor to reduce deceleration time (use rate: 3% ED). Braking Resistor Unit LKEB- (75600-K0) Consumes the regenerative motor energy with a resistor to reduce deceleration time (use rate: 10% ED). Braking Unit CDBR- (72600-R0) Used with a Braking Resistor Unit to reduce the deceleration time of the motor. VS Operator (small plastic Operator) JVOP-95• (73041-0905X-) Allows frequency reference settings and ON/OFF operation control to be performed by analog references from a remote location (50 m max.). Frequency counter specifications: 60/120 Hz, 90/180Hz VS Operator (Standard steelplate Operator) JVOP-96• (73041-0906X-) Allows frequency reference settings and ON/OFF operation control to be performed by analog references from a remote location (50 m max.). Frequency counter specifications: 75 Hz, 150 Hz, 220 Hz Extension cable to use a Digital Operator remotely. Cable length: 1 m or 3 m Controls an Inverter system VS System Module JGSM- A system controller that can be match to the automatic control system to produce an optimum system configuration. Provides Inverter momentary power loss recovery time Momentary Power Loss Recovery Unit P000 (73600-P000) Handles momentary power losses for the control power supply for models 7.5 kW or less (maintains power for 2 s). Frequency Meter DCF-6A Frequency Setter RV30YN20S (2 kΩ) Frequency Setter Knob CM-3S Output Voltmeter SCF-12NH Varispeed F7 DC reactor for power factor improvement Ground Output noise filter Zero phase reactor Motor Ground 1 m cable: (72606WV001) 3 m cable: (72606WV003) Variable Resistor Board for FreCorrect frequency refer- quency Reference ence input, frequency Frequency Meter meter, ammeter scales Scale Correction Resistor Molded-case circuit breaker or ground fault interrupter F6045GB (FIL001098) Digital Operator Connection Cable Set/monitor frequencies and voltages externally. Power supply Devices to set or monitor frequencies externally. Measures the output voltage externally and designed for use with a PWM Inverter. 2 kΩ (ETX003270) Connected to the control circuit terminals to input a frequency 20 kΩ (ETX003120) reference. (RH000850) Calibrates the scale of frequency meters and ammeters. * 1. Use a ground fault interrupter with a current sensitivity of 200 mA minimum and an operating time of 0.1 s minimum to prevent operating errors. The interrupter must be suitable for high-frequency operation. Example: NV series by Mitsubishi Electric Corporation (manufactured in or after 1988) EG, SG series by Fuji Electric Co., Ltd. (manufactured in or after 1984) * 2. The finement zero-phase reactor is manufactured by Hitachi Metals. 9-6 Specifications of Options and Peripheral Devices The following option boards are available Table 9.5 Option Boards Type Name Document Number 73600C001X TOE-C73630.13 73600C002X Enables high-precision, high-resolution setting of analog speed references. • Input signal ranges: -10 to 10 V (20 kΩ) 4 to 20 mA (500 Ω), 3 channels • Input resolution: 13-bit + sign (1/8192) TOE-C73630.14 73600C003X Enables 8-bit digital setting of speed references. • Input signal: 8-bit binary 2-digit BCD + sign signal + set signal • Input voltage: +24 V (isolated) • Input current: 8 mA TOE-C73630.15 73600C016X Enables 16-bit digital setting of speed references. • Input signal: 16-bit binary 4-digit BCD + sign signal + set signal • Input voltage: +24 V (isolated) • Input current: 8 mA With 16-bit/12-bit switch. TOE-C73640.7 73600D001X Converts analog signals to monitor the Inverter's output status (output frequency, output current, etc.) to absolute values and outputs them. • Output resolution: 8 bits (1/256) • Output voltage: 0 to +10 V (not insulated) • Output channels: 2 channels TOE-C73630.21 73600D002X Output analog signals to monitor the Inverter's output status (output frequency, output current, etc.). • Output resolution: 11 bits (1/2048) + sign • Output voltage: -10 to +10 V (not insulated) • Output channels: 2 channels TOE-C73630.22 Digital Output Board DO-08 73600D004X Outputs isolated digital signals to monitor the Inverters operating status (alarm signals, zero-speed detection, etc.) Output form: Photocoupler output, 6 channels (48 V, 50 mA max.) Relay contact outputs, 2 channels (250 VAC: 1 A max., 30VDC: 1 A max.) TOE-C73630.24 2C-Relay Output Board DO-02C 73600D007X Provides two multi-function outputs (DPDT relay contacts) in addition to those provided by the Inverter. TOE-C73640.8 Analog Reference Board AI-14B Speed (Frequency) Reference Digital ReferOption ence Board Boards DI-08 Digital Reference Board DI-16H2 Analog Monitor Board AO-08 Monitoring Option Boards Function Enables high-precision, high-resolution setting of analog speed references. • Input signal ranges: 0 to 10 V (20 kΩ), 1 channel 4 to 20 mA (250 Ω), 1 channel • Input resolution: 14-bit (1/16384) Analog Reference Board AI-14U Built-in (connect to connector) Code Number Analog Monitor Board AO-12 9-7 Table 9.5 Option Boards (Continued) Type Name PG-A2 Built-in (connect to connector) PG Speed Control Boards PG-B2 PG-D2 PG-X2 9-8 Code Number Function Document Number 73600A012X Used for V/f with PG control. Speed feedback is performed using the PG attached to the motor to compensate for speed fluctuations caused by slipping. • A-phase pulse (single pulse) input (voltage, complementary, open-collector input) • Maximum input frequency: 32767 Hz • Pulse monitor output: +12 V, 20 mA (PG power supply output: +12 V, 200 mA max.) TOE-C73640.1 73600A013X • Used for V/f control with PG and flux vector control. • A-, B-phase input (complimentary input) • Maximum input frequency: 32767 Hz • Pulse monitor output: Open-collector (PG power supply output: +12 V, 200 mA max.) TOE-C73640.2 73600A014X • Differential input. • A-phase pulse (differential pulse) input, for V/f control • Maximum input frequency: 300 kHz • Input: Conforms to RS-422 • Pulse monitor output: RS-422 (PG power supply output: +5 or +12 V, 200 mA max.) TOE-C73640.3 73600A015X • • • • A-, B-, Z-phase pulse (differential pulse) input Maximum input frequency: 300 kHz Input: Conforms to RS-422 Pulse monitor output: RS-422 (PG power supply output: +5 or +12 V, 200 mA max.) TOE-C73640.4 Specifications of Options and Peripheral Devices Table 9.5 Option Boards (Continued) Type Name Code Number Function Document Number DeviceNet Communications Interface Board SI-N 73600C021X Used to communicate with an Inverter from a host computer using DeviceNet communications to start/stop Inverter operation, read/set parameters, and read/set monitor constants (output frequencies, output currents, etc.). - ProfiBus-DP Communications Interface Board SI-P 73600C022X ProfiBus-DP Communications Interface Board SI-P1 - 73600C033X Used to communicate with an Inverter from a host computer using ProfiBus-DP communications to start/stop Inverter operation, read/set parameters, and read/set monitor constants (output frequencies, output currents, etc.). *1 Used to communicate with an Inverter from a host computer using InterBus-S communications to start/stop Inverter operation, read/set parameters, and read/set monitor constants (output frequencies, output currents, etc.). - *1 Used to communicate with an Inverter from a host computer using CANopen communications to start/stop Inverter operation, read/set parameters, and read/set monitor constants (output frequencies, output currents, etc.). - ControlNet Communications Interface Board SI-U *1 Used to communicate with an Inverter from a host computer using ControlNet communications to start/stop Inverter operation, read/set parameters, and read/set monitor constants (output frequencies, output currents, etc.). - CC-Link Communications Interface Board SI-C 73600C032X Used to communicate with an Inverter from a host computer using CC-Link communications to start/stop Inverter operation, read/set parameters, and read/set monitor constants (output frequencies, output currents, etc.). - LONWORKS Communications Interface Board SI-J 73600C035X Used to communicate with an Inverter from a host computer using LONWORKS communications to start/stop Inverter operation, read/set parameters, and read/set monitor constants (output frequencies, output currents, etc.). - 73600C034X Used to communicate with an Inverter from a host computer using LONWORKS communications to start/stop Inverter operation, read/set parameters, and read/set monitor constants (output frequencies, output currents, etc.). With Display Data Channel (DDC) function. - InterBus-S Communications Interface Board SI-R Built-in Com(conmuninected cations to con- Option nector) Boards CANopen Communications Interface Board SI-S1 LONWORKS Communications Interface Board SI-W1 MECHATROLINKCommunications Interface Board SI-T *2 Used to communicate with an Inverter from a host computer using MECHATROLINK communications to start/stop 100-017-994 Inverter operation, read/set parameters, and read/set monitor constants (output frequencies, output currents, etc.). - * 1. Under development. * 2. Applicable for G7-Series Inverters with software versions PRG: S1038 or later 9-9 10 Appendix This chapter provides precautions for the Inverter, motor, and peripheral devices and also provides lists of constants. Varispeed G7 Control Methods..................................10-2 Inverter Application Precautions ................................ 10-6 Motor Application Precautions ...................................10-9 Conformance to UL Standard .................................. 10-11 Conformance to CE Markings..................................10-13 Wiring Examples ......................................................10-20 User Constants ........................................................10-29 10 Varispeed G7 Control Methods Details of the Varispeed G7-Series Inverter control methods and their features are provided in this section. Control Methods and Features Varispeed G7-Series Inverters support the following five control methods, allowing the selection of a control method to suit the required purpose. Table 10.1 provides an overview of the control methods and their features. Table 10.1 Overview and Features of Control Methods Control Method Constant Setting Basic Control Main Applications PG Speed Control Board (Option) Basic Performance V/f Control with PG Open-loop Vector 1 Control Flux Vector Control Open-loop Vector 2 Control A1-02 = 0 A1-02 = 1 A1-02 = 2 (factory setting) A1-02 = 3 A1-02 = 4 Current vector control with a PG Current vector control without a PG using a highperformance magnetic flux and speed estimator (software) Voltage/frequency fixed ratio control Voltage/frequency with speed comfixed ratio control pensation using a PG Current vector control without a PG Variable speed control, particuApplications larly for control of requiring highmultiple motors precision speed with a single control using a PG Inverter and for on the machine replacing existing side Inverters Very high-performance control Variable speed Very high-perfor- without a PG on control, applicamance control the motor side tions requiring with a PG on the (such as simple high performance motor side (simservodrives, without a PG on ple servodrives, torque control, and the motor side, high-precision torque limiting), and for replacing speed control, and function appliopen-loop vector torque control, and cations between control of the pretorque limiting) flux vector and vious VS-616G5. open-loop vector 1 control. Not required. Required (PG-A2 or PG-D2). Not required. Required (PG-B2 or PG-X2). Not required. Speed Control Range*1 1:40 1:40 1:100 1:1000 1:200 (1:10 on regenerative side) Speed Control Accuracy*2 ±2 to 3% ±0.03% ±0.2% ±0.02% ±0.2% Speed Response*3 Approx. 1 Hz Approx. 1 Hz 5 Hz 40 Hz 10 Hz Maximum Output Frequency 400 Hz 400 Hz 400 Hz 400 Hz 60 Hz, 120 Hz 150%/3 Hz 150%/3 Hz 150%/1 Hz 150%/0 min−1 150%/0.3 Hz Starting Torque*4 10-2 V/f Control Varispeed G7 Control Methods Table 10.1 Overview and Features of Control Methods (Continued) Control Method Autotuning Torque Limiting*5 Torque Control*6 Application Functions V/f Control Line-to-line resistance (Normally not required.) No No V/f Control with PG Open-loop Vector 1 Control Flux Vector Control Open-loop Vector 2 Control Rotational Rotational Rotational autotuning, staautotuning, staautotuning, staLine-to-line resis- tionary autotuning, tionary autotuning, tionary autotuning, tance (Normally stationary stationary stationary not required.) autotuning for autotuning for autotuning for line-to-line resis- line-to-line resis- line-to-line resistance only tance only tance only No No Yes (except during acceleration/ deceleration, below minimum frequency, or during reverse rotation) Yes Yes (except below minimum frequency and during reverse rotation) No Yes Yes (except below minimum frequency and during reverse rotation) Yes (Except below minimum frequency and during reverse rotation) Droop Control*7 No No No Yes (except for 0 min−1 and during reverse rotation) Zero-servo Control*8 No No No Yes No Speed Estimation (Detection) Instantaneous Speed Search*9 Yes (speed and rotation direction estimation) Yes (speed detection and rotation direction estimation) Yes (speed and rotation direction estimation) Yes (speed and rotation direction detection) Yes (speed and rotation direction estimation) Automatic Energy-saving Control*10 Yes Yes Yes Yes Yes High-slip Braking*11 Yes Yes (Under development) (Under development) (Under development) Feed Forward Control*12 No No No Yes Yes 10 * 1. The variable speed control range. (For continuous operation, the motor's temperature rise must be considered.) * 2. The speed deviation in relation to the maximum speed with a rated load and when the load is stable. (For open-loop vector 1 and 2 control, the motor temperature must be 25 °C ± 10 °C.) * 3. The speed response guidelines indicating the extent of the motor's actual speed gain in proportion to the speed reference, which changes in a sinusoidal wave form, within a range where motor torque does not become saturated. * 4. A guideline for the motor torque that can be generated when started at a low speed and its output frequency (rotations) at that time. * 5. This function limits the maximum motor torque to protect the machine and the load. * 6. This function directly controls the amount of torque being generated at the motor and its rotation direction, e.g., to control force. * 7. This function controls the amount of motor slip that occurs to prevent mechanical shock, when replacing a torque motor, etc. * 8. This function performs simple positioning control (servo lock), without using an external positioning control device. * 9. This function instantaneously estimates (or detects) the speed and rotation direction of a coasting motor, and quickly starts it without subjecting it to shock. * 10.This function automatically adjusts the voltage applied to the motor to optimize the motor's efficiency with light loads. * 11.This function improves the deceleration time without using a braking resistor by making the motor winding absorb regenerative power. As a standard, this function is effective with a motor running on 160 kW or less with a high-inertia load. * 12.This function enables proportional gain in relation to changes in the speed reference, even for low rigidity (corresponds to the servo's model gain control). * 13.Set the maximum output frequency (E1-04) for open-loop vector 2 control to 60 Hz max. (120 Hz max. for PRG: 102). For torque control on the regenerative side, use in the speed range 1:10. 10-3 Application Function Precautions Observe the following precautions when using the application functions. • Perform rotational autotuning during trial operation whenever it is possible to separate the motor and machine. To achieve the characteristics of vector control described in Table 10.1, the control must be adjusted within a range that the machine will not vibrate after rotational autotuning has been performed. • With vector control, the motor and Inverter must be connected 1:1. Vector control is not possible when multiple motors are connected to a single Inverter. Select an Inverter capacity so the rated motor current is 50% to 100% of the rated Inverter current. • For estimated speed searching, the motor and Inverter must be connected 1:1. The speed search must be performed at a frequency of 130 Hz or less and with a motor with the same number of frames as or one frame less than the Inverter capacity. • During high-slip braking, motor loss increases, so use a high-slip braking frequency of 5% ED or less, and a braking time of 90 seconds or less. Once high-slip braking has started, the motor cannot be restarted until it has stopped. • Feed forward control is a function that improves the proportional gain of the motor speed in relation to the change in the speed reference. Adjust the response to interference loads using the speed controller (ASR) constants. • The torque limit function will not operate during acceleration or deceleration (during soft start transition) when using a control method such as open-loop vector 1 control. Even if the motor speed drops due to torque limiting while set to a fixed speed, the speed will not fall below the minimum frequency and the motor will not slip into reverse rotation. These conditions also apply to open-loop vector 2 control and other application functions. Precautions for Open-loop Vector 2 Control (PRG: 102 only) In open-loop vector 2 control, two speed estimators are switched between and, if used at a maximum frequency exceeding 70 Hz, there may be instances of shock occurring at the switchover. If switching shock is a problem, reduce the switching frequency (N4-11 and N4-28). If the problem still occurs after making this adjustment, use open-loop vector 1 control. Do not use open-loop vector 2 control for elevating machines. Any other control method can be used. Control Methods and Applications Application examples for the Inverter control methods are provided here. V/f Control (A1-02 = 0) V/f control is suitable for applications where multiple motors are operated with a single Inverter, such as with multi-motor drives. (Thermal relay) Inverter M1 M2 M3 Fig 10.1 10-4 Varispeed G7 Control Methods V/f Control with PG (A1-02 = 1) V/f control with a PG enables precise control of machine line speed. Speed control using the speed feedback of the machine shaft is possible in this mode. Conveyor Inverter M PG PG Speed Control Board (PG-A2 or PG-D2) Fig 10.2 Open-loop Vector Control (A1-02 = 2 or 4) Open-loop vector control enables the use of high-performance drives without a speed detector. PG (pulse generator) wiring is not required. Inverter M Fig 10.3 Flux Vector Control (A1-02 = 3) Flux vector control is suitable for applications using high-precision drives with PG feedback. High-precision positioning, zero-speed control, and torque control are possible with this mode. Inverter M PG PG Speed Control Board (PG-B2 or PG-X2) Fig 10.4 10 10-5 Inverter Application Precautions This section provides precautions for selecting, installing, setting, and handling Inverters. Selection Observe the following precautions in selecting an Inverter. Installing Reactors A large peak current will flow in the power input circuit when the Inverter is connected to a large-capacity power transformer (600 kVA or higher) or when switching a phase advancing capacitor. Excessive peak current can destroy the convertor section. To prevent this, install a DC or AC reactor (optional) to improve the power supply power factor. DC reactors are built into 200 V Class Inverters of 18.5 to 110 kW and 400 V Class Inverters of 18.5 to 300 kW. If a thyristor convertor, such as a DC drive, is connected in the same power supply system, connect a DC or AC reactor regardless of the power supply conditions shown in the following diagram. Power supply capacity (kVA) DC or AC reactor Required DC or AC reactor Not required Inverter capacity (kVA) Fig 10.5 Inverter Capacity When connecting special motors or multiple motors in parallel to an Inverter, select the Inverter capacity so that the rated output current of the Inverter is 1.1 times the sum of all the motor rated currents. Applications with Repetitive Loads Applications with repetitive loads (cranes, elevators, presses, washing machines, etc.) using Inverters require derating for the repetitive load [reducing carrier frequency and current (changing accel/decel timing, increasing the frame size of the Inverter)]. Refer to Current Alarm Function and Peak Hold Current Monitoring Function in Chapter 6 to confirm the output current during startup. Initial Torque The startup and acceleration characteristics of the motor are restricted by the overload current ratings of the Inverter that is driving the motor. The torque characteristics are generally less than those required when starting using a normal commercial power supply. If a large initial torque is required, select an Inverter with a somewhat larger capacity or increase the capacity of both the motor and the Inverter. Emergency Stop Although the Inverter's protective functions will stop operation when a fault occurs, the motor will not stop immediately. Always provide mechanical stop and protection mechanisms on equipment requiring an emergency stop. 10-6 Inverter Application Precautions Options Terminals B1, B2, , 1, 2, 3 are for connecting only the options specifically provided by Yaskawa. Never connect any other devices to these terminals. Installation Observe the following precautions when installing an Inverter. Installation in Enclosures Either install the Inverter in a clean location not subject to oil mist, air-bourne matter, dust, and other contaminants, or install the Inverter in a completely enclosed panel. Provide cooling measures and sufficient panel space so that the temperature surrounding the Inverter does not go beyond the allowable temperature. Do not install the Inverter on wood or other combustible materials. Installation Direction Mount the Inverter vertically to a wall or other horizontal surface. Settings Observe the following precautions when making settings for an Inverter. Upper Limits The Digital Operator can be used to set high-speed operation up to a maximum of 400 Hz (depends on the carrier frequency). Incorrect settings can be dangerous. Use the maximum frequency setting functions to set upper limits. (The maximum output frequency is factory-set to 60 Hz.) DC Injection Braking The motor can overheat if the DC injection braking voltage or braking time is set to a large value. Acceleration/Deceleration Times The motor's acceleration and deceleration times are determined by the torque generated by the motor, the load 10 (GD2/4). torque, and the load's inertial moment If the stall prevention functions are activated during acceleration or deceleration, increase the acceleration or deceleration time. The stall prevention functions will increase the acceleration or deceleration time by the amount of time the stall prevention function is active. To reduce the acceleration or deceleration times, increase the capacity of the motor and Inverter. 10-7 Handling Observe the following precautions when wiring or performing maintenance for an Inverter. Wiring Check The Inverter will be internally damaged if the power supply voltage is applied to output terminal U, V, or W. Check wring for any mistakes before supplying power. Check all wiring and sequences carefully. Magnetic Contactor Installation Do not start and stop operation frequently with a magnetic contactor installed on the power supply line. Doing so can cause the Inverter to malfunction. Do not turn the Inverter ON and OFF with a magnetic contactor more than one time every 30 minutes. Setting the Power Supply Voltage Jumper (400 V Class Inverters of 55 kW or Higher) If the jumper is inserted into a power tap that does not match the actual power supply voltage, the lifetime of the transformer for the power supply or the wind capacity of the cooling fan may be reduced. If the jumper is inserted and the voltage setting is too low for the actual power supply, a power surge may occur on the transformer for the power supply and reduce the lifetime of the transformer. If the jumper is inserted and the voltage setting is too high for the actual power supply, the wind capacity of the cooling fan is reduced. Insert the jumper into the power tap with the voltage setting nearest to the voltage of the actual power supply. Refer to Chapter 4 Trial Operation for the procedure. Maintenance and Inspections After turn OFF the main circuit power supply, always confirm that the CHARGE indicator is not lit before performing maintenance or inspections. The voltage remaining in the capacitor may cause electric shock. 10-8 Motor Application Precautions Motor Application Precautions This section provides precautions for motor application. Using the Inverter for an Existing Standard Motor When a standard motor is operated with the Inverter, power loss is slightly higher than when operated with a commercial power supply. Observe the following precautions when using an Inverter for an existing standard motor. Low Speed Ranges Cooling effects diminish in the low-speed range, resulting in an increase in the motor temperature. Therefore, the motor torque should be reduced in the low-speed range whenever using a motor not made by Yaskawa. If 100% torque is required continuously at low speed, consider using a special Inverter or vector motor. Installation Withstand Voltage If the input voltage is higher than the motor rated voltage or the wiring distance is long, the motor insulation voltage must be considered. Contact your Yaskawa representative for details. High-speed Operation When using the motor at a speed higher than the rated speed, problems may arise in dynamic balance and bearing durability. Contact your Yaskawa representative for details. Torque Characteristics The motor may require more acceleration torque when the motor is operated with the Inverter than when operated with a commercial power supply. Check the load torque characteristics of the machine to be used with the motor to set a proper V/f pattern. Vibration The Inverter uses a high carrier PWM to reduce motor vibration. (A constant can be set to select low carrier, PWM modulation control as well.) When the motor is operated with the Inverter, motor vibration is almost the same as when operated with a commercial power supply. Motor vibration may, however, become greater in the following cases. Resonance with the Natural Frequency of the Mechanical System 10 Take special care when a machine that has been operated at a constant speed is to be operated in variable speed mode. If resonance occurs, install vibration-proof rubber on the motor base or use the frequency jump function to skip any frequency resonating the machine. Imbalanced Rotor Take special care when the motor is operated at a speed higher than the rated speed. Noise Noise varies with the carrier frequency. At high carrier frequencies, the noise is almost the same when the motor is operated with a commercial power supply. Motor noise, however, becomes louder when the motor is operated at a speed higher than the rated speed. 10-9 Using the Inverter for Special Motors Observe the following precautions when using a special motor. Pole-changing Motor The rated input current of pole-changing motors differs from that of standard motors. Select, therefore, an appropriate Inverter according to the maximum input current of the motor to be used. Before changing the number of poles, always make sure that the motor has stopped. Otherwise, the overvoltage protective or overcurrent protective mechanism will be actuated, resulting in an error. Submersible Motor The rated input current of submersible motors is higher than that of standard motors. Therefore, always select an Inverter by checking its rated output current. When the distance between the motor and Inverter is long, use a cable thick enough to connect the motor and Inverter to prevent motor torque reduction. Explosion-proof Motor When an explosion-proof motor is to be used, it must be subject to an explosion-proof test in conjunction with the Inverter. This is also applicable when an existing explosion-proof motor is to be operated with the Inverter. Since the Inverter itself is, however, not explosion-proof, always install it in a safe place. Gearmotor The speed range for continuous operation differs according to the lubrication method and motor manufacturer. In particular, continuous operation of an oil-lubricated motor in the low speed range may result in burning. If the motor is to be operated at a speed higher than the rated speed, consult with the manufacturer. Synchronous Motor A synchronous motor is not suitable for Inverter control. If a group of synchronous motors is individually turned ON and OFF, synchronism may be lost. Single-phase Motor Do not use an Inverter for a single-phase motor. The motor should be replaced with a 3-phase motor. Power Transmission Mechanism (Speed Reducers, Belts, and Chains) If an oil-lubricated gearbox or speed reducer is used in the power transmission mechanism, oil lubrication will be affected when the motor operates only in the low speed range. The power transmission mechanism will make noise and experience problems with service life and durability if the motor is operated at a speed higher than the rated speed. 10-10 Conformance to UL Standard Conformance to UL Standard To comply with UL standard, follow the appropriate installation instructions. Installation Site Install the Inverter in a pollution degree 2 environment or equivalent. Specification of Closed-Loop Connector The closed-loop connectors must be installed on conductors before installing to terminal blocks. Use UL Listed closed-loop connectors shown below. Table 10.2 JST Closed-Loop Connector Model JST Kit P/N Inverter Model CIMR-G7A Input Output 27P5 14-5 14-5 2015 38-8 38-8 2018 60-8 38-8 2022 60-8 60-8 2030 80-10 80-10 2037 100-10 100-10 2045 60-10 (2perPh) 60-10 (2perPh) 2055 80-12 (2perPh) 80-10 (2perPh) 2075 150-12 (2perPh) 100-12 (2perPh) 2090 150-12 (2perPh) 150-12 (2perPh) 2110 200-12 (2perPh) 150-12 (2perPh) 4011 8-5 8-5 4015 14-5 14-5 4018 14-6 14-6 4022 22-6 22-6 4030 38-8 22-8 4037 38-8 38-8 4045 60-8 60-8 10 10-11 Control Circuit Terminal A UL Listed, Class 2 power supply must be used for the control circuits. See below table. . Table 10.3 Power Supply for Control Circuits Input/Output Terminal Open Collector Outputs P1, P2, P3, P4 PC, C3, C4 Digital Inputs S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, SC Analog Inputs RP, +V, -V, A1, A2, A3, AC Power Supply Class 2 power supply LVLC power supply when using internal power supply. Class 2 power supply when using external power supply. Interrupting Rating Varispeed F7 is suitable for use on a circuit capable of delivering not more than 100,000 RMS symmetrical amperes, 240 VAC maximum (200 V Class) and 480 VAC maximum (400 V Class). Use a circuit breaker or fuses having an interrupting rating not less than 100,000 RMS symmetrical amperes, 600 VAC maximum. Motor Overheat Protection To protect the motor from overheating, set the E2-01 constant in the Inverter to the same value as the level of the motor rated current. 10-12 Conformance to CE Markings Conformance to CE Markings Points regarding conformance to CE markings are given below. CE Markings CE markings indicate conformance to safety and environmental standards that apply to business transactions (including production, imports, and sales) in Europe. There are unified European standards for mechanical products (Machine Directive), electrical products (Low Voltage Directive), and electrical noise (EMC Directive). CE markings are required for business transactions in Europe (including production, imports, and sales). The Varispeed G7-Series Inverters bear CE markings indicating conformance to the Low Voltage Directive and the EMC Directive. • Low Voltage Directive: 73/23/EEC 93/68/EEC • EMC Directive: 89/336/EEC 92/31/EEC 93/68/EEC Machinery and installations that incorporate the Inverter are also subject to CE markings. It is ultimately the responsibility of customers making products incorporating the Inverter to attach CE markings to the finished products. The customer must confirm that the finished products (machines or installations) conform to the European Standards. Requirements for Conformance to CE Markings Low Voltage Directive Varispeed G7-Series Inverters satisfy testing for conformance to the Low Voltage Directive under the conditions described in European Standard EN50178. Requirements for Conformance to the Low Voltage Directive Varispeed G7-Series Inverters must satisfy the following conditions in order to conform to the Low Voltage Directive. • It must be used under conditions corresponding to overvoltage category 3 or less and pollution degree 2 or less as specified in IEC664. • Input fuses: For details on selecting fuses, refer to Table 10.4 Selection Requirements for Input Fuses with Examples. 10 • With Inverters CIMR-G7A2018 to 2110 and CIMR-G7A4018 to 4300, an enclosure preventing foreign matter from entering from the top or front sides is required (IP4X or higher: panel installation). 10-13 Wiring Example This example shows wiring for conforming to undervoltage reference. Thermal switch contact Braking Unit 3 (optional) Fuse 1MCCB 4 + 1 +0 -0 Level detector 2MCCB MC +1 B Motor *1 - +3 2 P Braking Resistor Unit (optional) FU - FU FV FW Noise filter Thermal relay trip contact Cooling fan IM FV FW 3-phase power R 200 to 240 V S 50/60 Hz T Inverter R/L1 S/L2 U U/T1 CIMR-G7A2018 V V/T2 T/L3 IM W W/T3 Vm 2MCCB THRX OFF ON MC MC Forward Run/Stop SA PG-B2 S1 (optional) Thermal relay trip contact for Braking Resistor Unit 1 2 Thermal relay trip contact for motor cooling fan 1 THRX Reverse Run/Stop SA Thermal switch contact for Braking Unit External fault S2 3 4 S3 TA1 1 2 3 4 5 6 C H B G A F TA3 2 MC TRX Fault reset SA Multi-step speed reference 1 (Main speed switching) S4 MC D Shielded twisted-pair wires TA2 1 S5 TRX 2 Pulse A Pulse monitor output 30 mA max. 3 MA Multi-function contact inputs Factory settings 4 S6 reference 2 Multi-step speed Jog frequency selection Fault contact Pulse B Wiring distance: d 30 m max. S7 External baseblock command S8 MP Multi-step speed reference 3 S9 AC Multi-step speed reference 4 S10 Acc/dec time 1 S11 Emergency stop (NO) S12 Pulse train output 0 to 32 kHz (2.2 kΩ) Default: Output frequency Ammeter adjustment AM 20k Ω - CN5 (NPN setting) +24V 8mA Multi-function analog output 2 -10 to 10 V 2 mA AM + Default: Output current 0 to +10 V Ammeter adjustment FM SC 20k Ω - AC FM + Multi-function analog output 1 -10 to 10 V 2 mA +24V Shield wire connection terminal E (G) Pulse train input RP Master speed pulse train 0 to 32 kHz (3 kΩ) High level: 3.5 to 13.2 V input Frequency setting 2kΩ adjustment Frequency setter 3 External frequency references PG 2kΩ 0 to +10V 2 1 4 to 20mA 0 to +10V P P P +V Frequency setting power +15 V, 20 mA A1 A2 Master speed reference 0 to 10 V (20 kΩ) Master speed reference 4 to 20 mA (250 Ω) [0 to 10 V (20 kΩ) input] A3 Multi-function anlog input 0 to 10 V (20 kΩ) AC 0V Terminating resistance MEMOBUS communications RS-485/422 E(G) *2 MA R+ RS+ MA Error contact output 250 VAC, 10 mA min. 1 A max. 30 VDC, 10 mA min. 1 A max. MB MC M1 M2 MC Multi-function contact output 250 VAC, 10 mA min. 1 A max. 30 VDC, 10 mA min. 1 A max. Default: Running signal P1 Factory setting: Not used -V ( -15V 20mA) Default: Output frequency 0 to +10 V Open collector 1 Default: Zerospeed P2 PC P3 C3 S- P4 IG C4 Open collector 2 Multi-function open-collector outputs 48 VDC 50 mA max. Default: Frequency agree signal Open collector 3 Factory setting: Inverter operation ready Open collector 4 Factory setting: minor fault *3 * 1. The main circuit is separated from the terminal cover for safety reasons. * 2. The contact output circuit is separated from the main circuit and the control circuit by reinforced insulation. It can be connected to extra-low voltage circuits or circuits that are 250 VAC 1 A, 30 VDC 1 A or less. * 3. The control circuit is an extra-low voltage circuit and separated from the main circuit and the contact output circuit by reinforced insulation. Always connect it to extra-low voltage circuits. Fig 10.6 10-14 Conformance to CE Markings Input Fuses In order to conform to the Low Voltage Directive, fuses must be provided for inputs. Use UL-compatible input fuses with ratings higher than the voltages and currents, and fusing I2t specifications within the ranges shown in the table below. Table 10.4 Selection Requirements for Input Fuses with Examples Voltage Class 200 V Class Selection Requirements Input Fuse (Examples) Inverter Model Number CIMR-G7A Voltage (V) Current (A) Fusing I2t (A2sec) 20P4 240 10 12 to 25 A60Q12-2 FERRAZ 600V 12A 17 20P7 240 15 23 to 55 CR2LS-20/UL FUJI 600V 12A 27 21P5 240 20 34 to 98 CR2LS-30/UL FUJI 250V 20A 60 22P2 240 30 82 to 220 CR2LS-50/UL FUJI 250V 30A 200 23P7 240 40 220 to 610 CR2LS-75/UL FUJI 250V 50A 560 25P5 240 50 290 to 1300 CR2LS-75/UL FUJI 250V 75A 560 27P5 240 60 450 to 5000 CR2LS-100/UL FUJI 250V 75A 810 2011 240 90 1200 to 7200 CR2L-125/UL FUJI 250V 100A 1570 2015 240 120 1800 to 7200 CR2L-150/UL FUJI 250V 125A 2260 2018 240 140 870 to 16200 CR2L-150/UL FUJI 250V 150A 2260 2022 240 160 1500 to 23000 CR2L-200/UL FUJI 250V 150A 4010 2030 240 220 2100 to 19000 CR2L-260/UL FUJI 250V 200A 7320 2037 240 270 2700 to 55000 CR2L-300/UL FUJI 250V 260A 9630 2045 240 300 4000 to 55000 CR2L-300/UL FUJI 250V 300A 9630 2055 240 370 7100 to 64000 CR2L-400/UL FUJI 250V 350A 24000 2075 240 500 11000 to 64000 CR2L-500/UL FUJI 250V 450A 40000 2090 240 600 13000 to 83000 CR2L-600/UL FUJI 250V 600A 52000 2110 240 700 13000 to 83000 A50P700-4 FERRAZ 250V 600A 49000 Model Number Manufacturer Ratings Fusing I2t (A2sec) 10 10-15 Table 10.4 Selection Requirements for Input Fuses with Examples (Continued) Voltage Class 400 V Class 10-16 Selection Requirements Input Fuse (Examples) Inverter Model Number CIMR-G7A Voltage (V) Current (A) Fusing I2t (A2sec) 40P4 480 5 16 to 660 CR6L-20/UL FUJI 600V 20A 26 40P7 480 10 19 to 660 CR6L-20/UL FUJI 600V 20A 26 41P5 480 10 46 to 660 CR6L-30/UL FUJI 600V 30A 59 42P2 480 15 78 to 660 CR6L-50/UL FUJI 600V 50A 317 43P7 480 20 110 to 660 CR6L-50/UL FUJI 600V 50A 317 44P0 480 30 220 to 660 CR6L-50/UL FUJI 600V 50A 317 45P5 480 40 240 to 900 CR6L-50/UL FUJI 600V 50A 317 47P5 480 50 320 to 900 CR6L-75/UL FUJI 600V 75A 564 4011 480 50 1000 to 1800 CR6L-100/UL FUJI 600V 100A 1022 4015 480 60 1500 to 4100 CR6L-150/UL FUJI 600V 150A 3070 4018 480 70 530 to 5800 CR6L-150/UL FUJI 600V 150A 3070 4022 480 90 1130 to 5800 CR6L-150/UL FUJI 600V 150A 3070 4030 480 110 1700 to 5800 CR6L-150/UL FUJI 600V 150A 3070 4037 480 140 2000 to 13000 CR6L-200/UL FUJI 600V 200A 5200 4045 480 160 3000 to 13000 CR6L-200/UL FUJI 600V 200A 5200 4055 480 220 6800 to 55000 CR6L-300/UL FUJI 600V 300A 17700 4075 480 280 9000 to 55000 CR6L-300/UL FUJI 600V 300A 17700 4090 480 330 12000 to 23000 A70P400-4 FERRAZ 700V 400A 19000 4110 480 400 18000 to 64000 A70P450-4 FERRAZ 700V 450A 24000 4132 480 450 28000 to 250000 A70P600-4 FERRAZ 700V 600A 43000 4160 480 540 40000 to 250000 A70P700-4 FERRAZ 700V 700A 59000 4185 480 620 43000 to 400000 A70P900-4 FERRAZ 700V 900A 97000 4220 480 750 63000 to 400000 A70P900-4 FERRAZ 700V 900A 97000 4300 480 1000 94000 to 920000 A70P1000-4 FERRAZ 700V 1000A 120000 Model Number Manufacturer Ratings Fusing I2t (A2sec) Conformance to CE Markings EMC Directive Varispeed G7-Series Inverters satisfy testing for conformance to the EMC Directive under the conditions described in European Standard EN61800-3. Installation Method In order to ensure that the machinery or installation incorporating the Inverter conforms to the EMC Directive, perform installation according to the method below. • Install a noise filter that conforms to European Standards on the input side. (Refer to Table 10.5 EMC Noise Filters). • Use a shielded line or metal piping for wiring between the Inverter and Motor. Make the wiring as short as possible. • To suppress harmonics, install a DC reactor in CIMR-G7A20P4, 20P7, 40P4, and 40P7 models. (Refer to Table 10.6 DC Reactors for Suppressing Harmonics.) R/L1, S/L2, T/L3 PE Remove the paint on the ground side. Inputs Inverter Filter Outputs U/T1, V/T2, W/T3 R/L1, S/L2, T/L3 Wiring length: 40 cm max. Metallic plate Wiring length: 20 m max. Remove the paint on the ground side. IM Fig 10.7 Installation Method for Filter and Inverter (CIMR-G7A20P4 to 2015, 40P4 to 4015) 10 10-17 R/L1, S/L2, T/L3 PE Remove the paint on the ground side. Inputs Inverter Filter Outputs U/T1, V/T2, W/T3 R/L1, S/L2, T/L3 Wiring length: 40 cm max. Metallic plate Wiring length: 20 m max. Remove the paint on the ground side. IM Fig 10.8 Installation Method for Filter and Inverter (CIMR-G7A2018 to 2110, 4018 to 4300) Table 10.5 EMC Noise Filters Voltage Class 200V Class 10-18 Inverter Model Number CIMR-G7A Noise Filter (Made by Shaffner) Model Number Rated Current (A) Weight (kg) Dimensions (mm) 20P4 FS5972-10-07 10 1.1 141 × 46 × 330 20P7 FS5972-10-07 10 1.1 141 × 46 × 330 21P5 FS5972-18-07 18 1.3 141 × 46 × 330 22P2 FS5973-35-07 35 1.4 141 × 46 × 330 23P7 FS5973-35-07 35 1.4 141 × 46 × 330 25P5 FS5973-60-07 60 3 141 × 46 × 330 27P5 FS5973-60-07 60 3 206 × 60 × 355 2011 FS5973-100-07 100 4.9 236 × 80 × 408 2015 FS5973-100-07 100 4.9 236 × 80 × 408 2018 FS5973-130-35 130 4.3 90 × 180 × 366 2022 FS5973-130-35 130 4.3 90 × 180 × 366 2030 FS5973-160-40 160 6 120 × 170 × 451 2037 FS5973-240-37 240 11 130 × 240 × 610 2045 FS5973-240-37 240 11 130 × 240 × 610 2055 FS5972-400-99 400 18.5 300 × 160 × 610 2075 FS5972-400-99 400 18.5 300 × 160 × 610 2090 2110 FS5972-460-99 460 19.5 300 × 160 × 610 Conformance to CE Markings Table 10.5 EMC Noise Filters (Continued) Voltage Class Inverter Model Number CIMR-G7A 400V Class Noise Filter (Made by Shaffner) Model Number Rated Current (A) Weight (kg) Dimensions (mm) 40P4 FS5972-10-07 10 1.1 141 × 46 × 330 40P7 FS5972-10-07 10 1.1 141 × 46 × 330 41P5 FS5972-10-07 10 1.1 141 × 46 × 330 42P2 FS5972-18-07 18 1.3 141 × 46 × 330 43P7 FS5972-18-07 18 1.3 141 × 46 × 330 44P0 FS5972-18-07 18 1.3 141 × 46 × 330 45P5 FS5972-35-07 35 2.1 206 × 50 × 355 47P5 FS5972-35-07 35 2.1 206 × 50 × 355 4011 FS5972-60-07 60 4.0 236 × 65 × 408 4015 FS5972-60-07 60 4.0 236 × 65 × 408 4018 FS5972-70-52 70 3.4 80 × 185 × 329 4022 FS5972-70-52 70 3.4 80 × 185 × 329 4030 FS5972-130-35 130 4.7 90 × 180 × 366 4037 FS5972-130-35 130 4.7 90 × 180 × 366 4045 FS5972-130-35 130 4.7 90 × 180 × 366 4055 FS5972-170-40 170 6 120 × 170 × 451 4075 FS5972-170-40 170 6 120 × 170 × 451 4090 FS5972-250-37 250 11 130 × 240 × 610 4110 FS5972-250-37 250 11 130 × 240 × 610 4132 FS5972-410-99 410 10.5 260 × 115 × 386 4160 FS5972-410-99 410 10.5 260 × 115 × 386 4185 FS5972-600-99 600 18.5 260 × 135 × 386 4220 FS5972-800-99 800 31 300 × 160 × 716 4300 FS5972-800-99 800 31 300 × 160 × 716 Table 10.6 DC Reactors for Suppressing Harmonics Voltage Class 200 V Class 400 V Class Inverter Model Number CIMR-G7A 20P4 20P7 40P4 40P7 DC Reactor Model Number Manufacturer Ratings Code Number 10 UZDA-B YASKAWA 5.4 A 8 mH X010084 UZDA-B YASKAWA 3.2 A 28 mH X010052 10-19 Wiring Examples This section provides wiring examples to connect a Braking Unit and other peripheral devices to the main circuits, examples of wiring a transformer to Inverter I/O, and other aspects of Inverter wiring. Using a Braking Resistor Unit This example shows wiring for a Braking Resistor Unit. CIMR-G7A20P4 to -G7A2015 (200 V Class Inverters of 0.4 to 15 kW) CIMR-G7A40P4 to -G7A4015 (400 V Class Inverters of 0.4 to 15 kW) A sequence is required to turn OFF the power supply for the thermal overload relay trip contacts of the Braking Resistor Unit. Braking Resistor overheating contacts (Thermal overload relay trip contacts) DC Reactor to improve input power factor Braking Resistor Unit *3 (Optional) Short-circuit bar MC 3-phase power 200 to 230 V 50/60 Hz or 380 to 460 V 50/60 Hz *4 R/L1 S/L2 T/L3 Inverter U/T1 V/T2 W/T3 Motor 200 V Class Inverters: Ground to 100 Ω max., 400 V Class Inverters: Ground to 10 Ω max.) Overload relay trip contact of Braking Resistor Unit Fault contacts * 1. A transformer is not required for 200 V Class * 2. Remove the short-circuit bar (normally connected) from + 1 and + 2 when connecting a DC Reactor (Optional). * 3. Disable stall prevention during deceleration by setting L3-04 and using a Braking Resistor Unit. The motor may not stop within the deceleration time if this setting is not changed. * 4. When connecting a separately-installed type Braking Unit (model CDBR) to Inverters with built-in braking transistor (200 V/400 V 15 kW or less), connect the B1 terminal of the Inverter to the + terminal of the Braking Unit and connect the - terminal of the Inverter to the - terminal of the Braking Unit. The B2 terminal is not used in this case. Fig 10.9 10-20 Wiring Examples Using a Braking Unit and Braking Resistor Unit When using a Braking Unit and Braking Resistor Unit, create a sequence to detect overheating of the braking resistor and cut off the power supply to the Inverter. CIMR-G7A2018, -G7A2022 (200 V Class Inverters of 18.5 kW, 22 kW) DC Reactor to improve input A sequence is required to turn power factor OFF the power supply for the (Optional) thermal overload relay trip contacts of the Braking Resistor Unit. Short-circuit bar Braking Unit (Optional) Braking Resistor Unit*2 (Optional) Level detector Braking Resistor overheating contacts (Thermal overload relay trip contacts) MCCB R/L1 S/L2 T/L3 3-phase power 200 to 230 V 50/60 Hz U/T1 V/T2 W/T3 Motor Inverter Ground to 100 Ω max. Overload relay trip contact of Braking Resistor Unit Forward Run/Stop Fault contacts Reverse Run/Stop Braking Unit Forward Run Command (forward run when ON) Reverse Run Command (reverse run when ON) External fault * 1. Remove the short-circuit bar (normally connected) from + 1 and + 2 when connecting a DC Reactor (Optional). * 2. Disable stall prevention during deceleration by setting L3-04 when using a Braking Resistor Unit. The motor may not stop within the deceleration time if this setting is not changed. Fig 10.10 10 10-21 Using Braking Units in Parallel This example shows wiring for using two Braking Units in parallel. There are connectors for selecting whether each Braking Unit is to be a Master or Slave. Select “Master” for the first Braking Unit only, and select “Slave” for all other Braking Units (i.e., from the second Unit onwards). A sequence is required to turn OFF the power supply for the thermal overload relay trip contacts of the Braking Resistor Unit. Thermal protector Braking Resistor Unit Braking Resistor Unit Level detector Thermal protector Braking Unit 2 Thermal switch Thermal switch MCCB R/L1 3-phase power 200 to 220 V 50 Hz 200 to 230 V 60 Hz Inverter U/T1 S/L2 V/T2 T/L3 Cooling fan W/T3 Motor Ground to 100 Ω max. Overload relay trip contact of Braking Resistor Unit Fault contacts Forward Run/Stop Reverse Run/Stop Braking Unit Fault contact output Forward Run Command (forward run when ON) Reverse Run Command (reverse run when ON) External fault * Disable stall prevention during deceleration by setting L3-04 to Resistor Unit. The motor may not stop within the deceleration time if this setting is not changed. Fig 10.11 10-22 Wiring Examples Using a Braking Unit and Three Braking Resistor Units in Parallel This example shows wiring for using three Braking Resistor Units in parallel. Thermal protector Thermal protector Braking Resistor Unit Level detector A sequence is required to turn OFF the power supply for the thermal overload relay trip contacts of the Braking Resistor Unit. Thermal protector Braking Resistor Unit Braking Resistor Unit Braking Unit Thermal switch MCCB R/L1 3-phase power 380 to 480 V 50/60 Hz S/L2 Inverter U/T1 Motor V/T2 W/T3 T/L3 Cooling fan Voltage setting Ground to 10 Ω max. Overload relay trip contact of Braking Resistor Unit Fault contact output Fault contacts Forward Run/Stop Reverse Run/Stop Braking Unit Forward Run Command (forward run when ON) Reverse Run Command (reverse run when ON) External fault * Disable stall prevention during deceleration by setting L3-04 to Resistor Unit. The motor may not stop within the deceleration time if this setting is not changed. Fig 10.12 10 10-23 Using a VS Operator This example shows wiring for using a VS Operator. The VS Operator model number is JVOP-95• or JVOP-96 •. CIMR-G7A27P5 (200 V Class Inverters of 7.5 kW) Short-circuit bar (Standard) MCCB R/L1 3-phase power S/L2 Inverter U/T1 Motor V/T2 W/T3 T/L3 JVOP-95•, C-96• VS Operator Forward Run Command (forward run when closed) Reverse Run Command (reverse run when closed) Ground to 100 Ω max. Multi-function contact inputs Sequence common (0 V) Shield terminal Speed setting power (15 V, 20 mA) Master speed (0 to 10 V, 20 kΩ) Master speed (4 to 20 mA, 250 Ω) Multi-function contact output (Default: Running signal) Fault contact output Open collector 1 (Default: Zero-speed signal) Frequency meter Multi-function analog output Multi-function analog output (Default: Output frequency) Fig 10.13 10-24 Open collector 2 (Default: Speed agreement signal) Multi-function output common Multi-function opencollector output 48 V, 50 mA max. Wiring Examples Using Transistors for Input Signals and a 0-V Common in Sinking Mode with an Internal Power Supply Set CN5 (shunt connector) on the control board to NPN as shown below for a sequence that uses an NPN transistor for an input signal (0-V command and sinking mode) and an internal +24-V power supply. +1 +2 - B1 B2 MCCB 3-phase power R R/L1 U/T1 Motor S S/L2 V/T2 IM T T/L3 Inverter W/T3 Ground S1 Forward Run/Stop S2 Reverse Run/Stop S3 External fault S4 Fault reset S5 Multi-function contact inputs Factory settings Multi-step speed setting 1 S12 CN5 (NPN setting) Emergency stop (NO contact) +24 V 8 mA SC +24 V E(G) Pulse train input Frequency setting adjustment 2 kΩ External frequency references Frequency setter 3 2 kΩ 0 to +10 V 2 1 4 to 20 mA P P Shield wire connection terminal RP Master speed pulse train 0 to 32 kHz (3 kΩ) High level: 3.5 to 13.2 V input +V Frequency setting power +15 V 20 mA A1 Master speed reference 0 to 10 V (20 kΩ) A2 AC 10 Master speed reference 4 to 20 mA (250 Ω) 0 to 10 V (20 kΩ) input 0V Fig 10.14 10-25 Using Transistors for Input Signals and a +24-V Common in Sourcing Mode Set CN5 (shunt connector) on the control board to PNP as shown below for a sequence that uses a PNP transistor for an input signal (+24-V common and sourcing mode) and an internal +24-V power supply. +1 +2 - B1 B2 MCCB 3-phase power R R/L1 S S/L2 T T/L3 Inverter U/T1 Motor V/T2 IM W/T3 Ground S1 Forward Run/Stop S2 Reverse Run/Stop S3 External fault S4 Fault reset S5 Multi-function contact inputs Factory settings Multi-step speed setting 1 S12 Emergency stop (NO contact) CN5 (PNP setting) +24 V 8 mA SC +24 V E(G) Pulse train input Frequency setting adjustment 2 kΩ External frequency references Frequency 3 setter 2 kΩ 0 to +10 V 2 1 4 to 20 mA P P Shield wire connection terminal RP Master speed pulse train 0 to 32 kHz (3 kΩ) High level: 3.5 to 13.2 V input +V Frequency setting power +15 V 20 mA A1 Master speed reference 0 to 10 V (20 kΩ) A2 AC Master speed reference 4 to 20 mA (250Ω) 0 to 10 V (20 kΩ) input 0V Fig 10.15 10-26 Wiring Examples Using Transistors for Input Signals and a 0-V Common in Sinking Mode with an External Power Supply Set CN5 (shunt connector) on the control board to EXT as shown below for a sequence that uses an NPN transistor for an input signal (0-V common and sinking mode) and an external +24-V power supply. +1 +2 - B1 B2 MCCB 3-phase power R R/L1 S S/L2 T T/L3 Inverter U/T1 Motor V/T2 IM W/T3 Ground S1 Forward Run/Stop S2 Reverse Run/Stop S3 External fault S4 Fault reset Multi-function contact inputs Factory settings S5 Multi-step speed setting 1 S12 Emergency stop (NO contact) CN5 (EXT setting) +24 V 8 mA External +24V SC +24 V E(G) Pulse train input RP Frequency setting adjustment 2 kΩ External frequency references Frequency setter 3 2 kΩ 0 to +10 V 4 to 20 mA Master speed pulse train 0 to 32 kHz (3 kΩ) High level: 3.5 to 13.2 V input 2 1 Shield wire connection terminal +V Frequency setting power A1 Master speed reference A2 AC Master speed reference +15 V 20 mA 0 to 10 V (20 kΩ) P P 10 4 to 20 mA (250 kΩ) 0 to 10 V (20 kΩ) input 0V Note: Set EXT as shown at the right even for a PNP input signal transistor sequence connection (+24-V common/sourcing mode) with a +24-V external power supply. S12 External +24V CN5 (EXT setting) +24 V 8 mA SC +24 V Fig 10.16 10-27 Using Contact and Open Collector Outputs This example shows wiring for contact outputs and open collector outputs. The following example is for the CIMR-G7A25P5 (200 V Class Inverter for 5.5 kW). +1 +2 B1 - B2 MCCB R R/L1 3-phase power S S/L2 T T/L3 Inverter U/T1 Motor V/T2 IM W/T3 Ground FM Ammeter scale adjustment resistor 20 k Multi-function analog output 2 -10 to +10 V 2 mA Default: Ouput current, AM 0 to +10 V Frequency meter scale adjustment resistor 20 k AC FM AM Multi-function analog output 1 -10 to +10 V 2 mA Default: Output frequency, 0 to +10 V E(G) Sequence Surge absorber MA MB MC Error contact output 250 VAC, 10 mA min. 1 A max. 30 VDC, 10 mA min. 1 A max. Multi-function contact output 250 VAC, 10 mA min. 1 A max. 30 VDC, 10 mA min. 1 A max. (Default: RUN) 250 VAC max. 30 VDC max. Flywheel diode M1 M2 48 VDC max. E(G) Flywheel diode P1 Open collector 1 (Default: zero speed) P2 PC 48 VDC max. Flywheel diode Open collector 2 (Default: Freq agree) Multi-function open collector output 48 VDC 50 mA max. Sequence external power supply Fig 10.17 10-28 User Constants User Constants Factory settings are given in the following table. Table 10.7 User Constants No. Name A1-00 Language selection for Digital Operator display A1-01 Constant access level A1-02 Control method selection A1-03 Factory Setting Setting No. Name Factory Setting 1*1 b3-05 Speed search wait time 0.2 2 b3-10 Speed search detection compensation gain (speed calculation) 1.10 2*1 b3-13 Proportional gain of the speed estimator during speed search 1.0 Initialize 0 b3-14 Rotation direction search selection 1 A1-04 Password 0 b3-17*18 Speed search retrial current level 150 A1-05 Password setting 0 b3-18*18 Speed search retrial detection time 0.10 - b3-19*18 Number of speed search retrials A2-01 to User setting constants A2-32 Setting 0 b1-01 Reference selection 1 b4-01 Timer function ON-delay time 0.0 b1-02 Operation method selection 1 b4-02 Timer function OFF-delay time 0.0 b1-03 Stopping method selection 0 b5-01 PID control method selection b1-04 Prohibition of reverse operation 0 b5-02 Proportional gain (P) 1.00 b1-05 Operation selection for setting E109 or less 0 b5-03 Integral (I) time 1.0 b1-06 Read sequence input twice 1 b5-04 Integral (I) limit 100.0 b1-07 Operation selection after switching to remote mode 0 b5-05 Derivative (D) time 0.00 b1-08 Run Command selection in programming modes 0 b5-06 PID upper limit 100.0 b1-10 Mode selection for zero-speed 0 b5-07 PID offset adjustment 0.0 b2-01 Zero-speed level (DC injection braking starting frequency) 0.5 b5-08 PID first order lag time constant 0.00 50 b5-09 PID output characteristics selection 0 0 b2-02 DC injection braking current b2-03 DC injection braking time at start 0.00 b5-10 PID output gain b2-04 DC injection braking time at stop 0.50 b5-11 PID reverse output selection 0 b2-08 Magnetic flux compensation volume 0 b5-12 Selection of PID feedback command loss detection 0 b3-01 Speed search selection 2*2 b5-13 PID feedback command loss detection level 0 b3-02 Speed search operating current 100*2 b5-14 PID feedback command loss detection time 1.0 b3-03 Speed search deceleration time 2.0 b5-15 PID sleep function operation level 0.0 10 1.0 10-29 Table 10.7 User Constants (Continued) No. 10-30 Name Factory Setting Setting No. Name Factory Setting b5-16 PID sleep operation delay time 0.0 C1-10 Accel/decel time setting unit b5-17 Accel/decel time for PID reference 0.0 C1-11 Accel/decel time switching frequency 0.0 b6-01 Dwell frequency at start 0.0 C2-01 S-curve characteristic time at acceleration start 0.20 b6-02 Dwell time at start 0.0 C2-02 S-curve characteristic time at acceleration end 0.20 b6-03 Dwell frequency at stop 0.0 C2-03 S-curve characteristic time at deceleration start 0.20 b6-04 Dwell time at stop 0.0 C2-04 S-curve characteristic time at deceleration end 0.00 b7-01 Droop control gain 0.0 C3-01 Slip compensation gain 1.0*2 b7-02 Droop control delay time 0.05 C3-02 Slip compensation primary delay time 200*2 b8-01 Energy-saving mode selection 0 C3-03 Slip compensation limit b8-02 Energy-saving gain 0.7*3 C3-04 Slip compensation selection during regeneration 0 b8-03 Energy-saving filter time constant 0.50*4 C3-05 Output voltage limit operation selection 0 b8-04 Energy-saving coefficient C4-01 Torque compensation gain 1.00 b8-05 Power detection filter time constant 20 C4-02 Torque compensation primary delay time constant 20*2 b8-06 Search operation voltage limiter 0 C4-03 Forward starting torque 0.0 b9-01 Zero-servo gain 5 C4-04 Reverse starting torque 0.0 b9-02 Zero-servo completion width 10 C4-05 Starting torque time constant 10 C1-01 Acceleration time 1 10.0 C5-01 ASR proportional (P) gain 1 20.00*7 C1-02 Deceleration time 1 10.0 C5-02 ASR integral (I) time 1 0.500*7 C1-03 Acceleration time 2 10.0 C5-03 ASR proportional (P) gain 2 20.00*7 C1-04 Deceleration time 2 10.0 C5-04 ASR integral (I) time 2 0.500*7 C1-05 Acceleration time 3 10.0 C5-05 ASR limit C1-06 Deceleration time 3 10.0 C5-06 ASR primary delay time 0.004*7 C1-07 Acceleration time 4 10.0 C5-07 ASR switching frequency 0.0 C1-08 Deceleration time 4 10.0 C5-08 ASR integral (I) limit 400 C1-09 Emergency stop time 10.0 C5-10 ASR primary delay time 2 288.20 *5 *6 1 200 5.0 0.010 Setting User Constants Table 10.7 User Constants (Continued) No. Name Factory Setting Setting No. Name Factory Setting 6*6 d3-01 Jump frequency 1 0.0 C6-03*8 Carrier frequency upper limit 15.0*6 d3-02 Jump frequency 2 0.0 C6-04*8 Carrier frequency lower limit 15.0*6 d3-03 Jump frequency 3 0.0 Carrier frequency proportional C6-05*8 gain 00 d3-04 Jump frequency width 1.0 C6-02 Carrier frequency selection C6-11 Carrier frequency for open-loop vector 2 control 4*6 d4-01 Frequency reference hold function selection 0 d1-01 Frequency reference 1 0.00 d4-02 + - Speed limits 10 d1-02 Frequency reference 2 0.00 d5-01 Torque control selection 0 d1-03 Frequency reference 3 0.00 d5-02 Torque reference delay time d1-04 Frequency reference 4 0.00 d5-03 Speed limit selection 1 d1-05 Frequency reference 5 0.00 d5-04 Speed limit 0 d1-06 Frequency reference 6 0.00 d5-05 Speed limit bias 10 d1-07 Frequency reference 7 0.00 d5-06 Speed/torque control switching timer 0 d1-08 Frequency reference 8 0.00 d5-07 Rotation direction limit operation selection 1 d1-09 Frequency reference 9 0.00 d6-01 Field weakening level 80 d1-10 Frequency reference 10 0.00 d6-02 Field frequency 0.0 d1-11 Frequency reference 11 0.00 d6-03 Field forcing function selection d1-12 Frequency reference 12 0.00 d6-05 AφR time constant 1.00 d1-13 Frequency reference 13 0.00 d6-06 Field forcing limit 400 d1-14 Frequency reference 14 0.00 E1-01 Input voltage setting 200*9 d1-15 Frequency reference 15 0.00 E1-03 V/f pattern selection F d1-16 Frequency reference 16 0.00 E1-04 Max. output frequency d1-17 Jog frequency reference 6.00 E1-05 Max. voltage d2-01 Frequency reference upper limit 100.0 E1-06 Base frequency 60.0*2 d2-02 Frequency reference lower limit 0.0 E1-07 Mid. output frequency 3.0*2 d2-03 Master speed reference lower limit 0.0 E1-08 Mid. output frequency voltage Setting 0*7 0 10 60.0*2 200.0 *2 *9 11.0*2 *9 10-31 Table 10.7 User Constants (Continued) No. 10-32 Name Factory Setting Setting No. Name Factory Setting 0.5*2 E4-01 Motor 2 rated current 1.90 *6 2.0*2 *9 E4-02 Motor 2 rated slip 2.90 *6 Mid. output frequency 2 0.0*10 E4-03 Motor 2 no-load current 1.20 *6 E1-12 Mid. output frequency voltage 2 0.0*10 E4-04 Motor 2 number of poles (number of poles) E1-13 Base voltage 0.0*11 E4-05 Motor 2 line-to-line resistance 9.842*6 E2-01 Motor rated current 1.90*6 E4-06 Motor 2 leak inductance 18.2*6 E2-02 Motor rated slip 2.90*6 E4-07 Motor 2 rated capacity 0.40*12 E2-03 Motor no-load current 1.20*6 F1-01 PG constant E2-04 Number of motor poles 4 F1-02 Operation selection at PG open circuit (PGO) 1 E2-05 Motor line-to-line resistance 9.842*6 F1-03 Operation selection at overspeed (OS) 1 E2-06 Motor leak inductance 18.2*6 F1-04 Operation selection at deviation 3 E2-07 Motor iron saturation coefficient 1 0.50 F1-05 PG rotation 0 E2-08 Motor iron saturation coefficient 2 0.75 F1-06 PG division rate (PG pulse monitor) 1 E2-09 Motor mechanical loss 0.0 F1-07 Integral value during accel/decel enable/disable 0 E2-10 Motor iron loss for torque compensation 14*6 F1-08 Overspeed detection level 115 E2-11 Motor rated output 0.40*12 F1-09 Overspeed detection delay time 0.0*7 E2-12 Motor iron saturation coefficient 3 1.30 F1-10 Excessive speed deviation detection level 10 E3-01 Motor 2 control method selection 2 F1-11 Excessive speed deviation detection delay time 0.5 E3-02 Motor 2 max. output frequency (FMAX) 60.0 F1-12 Number of PG gear teeth 1 0 E3-03 Motor 2 max. voltage (VMAX) 200.0*2 F1-13 Number of PG gear teeth 2 0 E3-04 Motor 2 max. voltage frequency (FA) 60.0 F1-14 PG open-circuit detection time E3-05 Motor 2 mid. output frequency 1 (FB) 3.0 *2 F2-01 Bi-polar or uni-polar input selection 0 E3-06 Motor 2 mid. output frequency voltage 1 (VC) 11.0 *9 F3-01 Digital input option 0 E3-07 Motor 2 min. output frequency (FMIN) 0.5 *2 F4-01 Channel 1 monitor selection 2 E3-08 Motor 2 min. output frequency voltage (VMIN) 2.0 *9 F4-02 Channel 1 gain E1-09 Min. output frequency E1-10 Min. output frequency voltage E1-11 4 600 2.0 1.00 Setting User Constants Table 10.7 User Constants (Continued) No. Name Factory Setting Setting No. Name Factory Setting 3 H1-03 Terminal S5 function selection 3 (0)*14 Channel 2 gain 0.50 H1-04 Terminal S6 function selection 4 (3)*14 F4-05 Channel 1 output monitor bias 0.0 H1-05 Terminal S7 function selection 6 (4)*14 F4-06 Channel 2 output monitor bias 0.0 H1-06 Terminal S8 function selection 8 (6)*14 F4-07 Analog output signal level for channel 1 0 H1-07 Terminal S9 function selection 5 F4-08 Analog output signal level for channel 2 0 H1-08 Terminal S10 function selection 32 F5-01 Channel 1 output selection 0 H1-09 Terminal S11 function selection 7 F5-02 Channel 2 output selection 1 H1-10 Terminal S12 function selection 15 F5-03 Channel 3 output selection 2 H2-01 Terminal M1-M2 function selection (contact) 0 F5-04 Channel 4 output selection 4 H2-02 Terminal P1 function selection (open collector) 1 F5-05 Channel 5 output selection 6 H2-03 Terminal P2 function selection (open collector) 2 F5-06 Channel 6 output selection 37 H2-04 Terminal P3 function selection (open-collector) 6 F5-07 Channel 7 output selection 0F H2-05 Terminal P4 function selection (open-collector) 10 F5-08 Channel 8 output selection 0F H3-01 Signal level selection (terminal A1) 0 F5-09 DO-08 output mode selection 0 H3-02 Gain (terminal A1) 100.0 F6-01 Operation selection after communications error 1 H3-03 Bias (terminal A1) 0.0 F6-02 Input level of external fault from Communications Option Board 0 H3-04 Signal level selection (terminal A3) 0 H3-05 1 Multi-function analog input (terminal A3) function selection 2 F6-03 Stopping method for external fault from Communications Option Board H3-06 Gain (terminal A3) 100.0 F6-04 Trace sampling from Communications Option Board 0 H3-07 Bias (terminal A3) 0.0 F6-06 Torque reference/torque limit selection from optical option 0 H3-08 Signal level selection (terminal A2) 2 Operation selection after SI-T F6-08∗13 WDT error 1 H3-09 Multi-function analog input (terminal A2) function selection 0 Number of SI-T BUS error detecF6-09∗13 tion 2 H3-10 Gain (terminal A2) 100.0 F4-03 Channel 2 monitor selection F4-04 H1-01 Terminal S3 function selection 24 H3-11 Bias (terminal A2) 0.0 H1-02 Terminal S4 function selection 14 H3-12 Analog input filter time constant 0.03 Setting 10 10-33 Table 10.7 User Constants (Continued) No. 10-34 Name Factory Setting Setting No. Name Factory Setting 2 L1-03 Alarm operation selection during motor overheating 3 Gain (terminal FM) 1.00 L1-04 Motor overheating operation selection 1 H4-03 Bias (terminal FM) 0.0 L1-05 Motor temperature input filter time constant 0.20 H4-04 Monitor selection (terminal AM) 3 L2-01 Momentary power loss detection 0 H4-05 Gain (terminal AM) 0.50 L2-02 Momentary power loss ridethru time 0.1*6 H4-06 Bias (terminal AM) 0.0 L2-03 Min. baseblock time 0.2*6 H4-07 Analog output 1 signal level selection 0 L2-04 Voltage recovery time 0.3*6 H4-08 Analog output 2 signal level selection 0 L2-05 Undervoltage detection level 190*9 H5-01 Slave address 1F L2-06 KEB deceleration time 0.0 H5-02 Communication speed selection 3 L2-07 Momentary recovery time 0*15 H5-03 Communication parity selection 0 L2-08 Frequency reduction gain at KEB start 100 H5-04 Stopping method after communication error 3 L3-01 Stall prevention selection during accel 1 H5-05 Communication error detection selection 1 L3-02 Stall prevention level during accel 150 H5-06 Send wait time 5 L3-03 Stall prevention limit during accel 50 H5-07 RTS control ON/OFF 1 L3-04 Stall prevention selection during decel 1 Unit Selection for MEMOBUS H5-10*18 Register 0025H 0 L3-05 Stall prevention selection during running 1 0 L3-06 Stall prevention level during running 160 H4-01 Monitor selection (terminal FM) H4-02 H6-01 Pulse train input function selection H6-02 Pulse train input scaling 1440 L3-11 Overvoltage inhibit selection H6-03 Pulse train input gain 100.0 L3-12 Overvoltage inhibit voltage level 380*9 H6-04 Pulse train input bias 0.0 L4-01 Speed agreement detection level 0.0 H6-05 Pulse train input filter time 0.10 L4-02 Speed agreement detection width 2.0 H6-06 Pulse train monitor selection 2 L4-03 Speed agreement detection level (+/-) 0.0 H6-07 Pulse train monitor scaling 1440 L4-04 Speed agreement detection width (+/-) 2.0 L1-01 Motor protection selection 1 L4-05 Operation when frequency reference is missing 0 L1-02 Motor protection time constant 1.0 L5-01 Number of auto restart attempts 0 0 Setting User Constants Table 10.7 User Constants (Continued) No. Name Factory Setting Setting No. Name Factory Setting L5-02 Auto restart operation selection 0 OH1 detection of Inverter’s coolL8-32*16 ing fan 1 L6-01 Torque detection selection 1 0 Carrier frequency reduction selecL8-38*18 tion 1*19 L6-02 Torque detection level 1 150 L8-39*18 Reduced carrier frequency L6-03 Torque detection time 1 0.1 L8-41*18 Current alarm L6-04 Torque detection selection 2 L6-05 2.0 *6 *19 0 0 N1-01 Hunting-prevention function selection Torque detection level 2 150 N1-02 Hunting-prevention gain 1.00 L6-06 Torque detection time 2 0.1 N1-03*17 Hunting-prevention time constant 10*6 L7-01 Forward drive torque limit 200 N2-01 Speed feedback detection control (AFR) gain 1.00 L7-02 Reverse drive torque limit 200 N2-02 Speed feedback detection control (AFR) time constant 50 L7-03 Forward regenerative torque limit 200 N2-03 Speed feedback detection control (AFR) time constant 2 750 L7-04 Reverse regenerative torque limit 200 N3-01 High-slip braking deceleration frequency width L7-06 Integral time setting for torque limit 200 N3-02 High-slip braking current limit 150 Control method selection for torque limit during acceleration deceleration N3-03 High-slip braking stop dwell time 1.0 L7-07 0 N3-04 High-slip braking OL time 40 Protect selection for internal DB resistor (Type ERF) 0 N4-07 Integral time of speed estimator L8-01 Setting 1 5 0.060 95*6 0.030 L8-02 Overheat pre-alarm level L8-03 Operation selection after overheat pre-alarm 3 N4-08 Proportional gain of speed estimator L8-05 Input open-phase protection selection 0 N4-10 High-speed proportional gain of speed estimator L8-07 Output open-phase protection selection 0 N4-11 Speed estimator switching frequency 70 L8-09 Ground protection selection 1 N4-15 Low-speed regeneration stability coefficient 1 0.3 L8-10 Cooling fan control selection 0 N4-17 Torque adjustment gain 0.8 L8-11 Cooling fan control delay time 60 N4-18 Feeder resistance adjustment gain 1.00 L8-12 Ambient temperature 45 N4-28 Speed estimator switching frequency 2 L8-15 OL2 characteristics selection at low speeds 1 N4-29 Torque adjustment gain 2 0.10 L8-18 Soft CLA selection 1 N4-30 Low-speed regeneration stability coefficient 2 1.00 15 15.0 10 50 10-35 Table 10.7 User Constants (Continued) No. * * * * * * * * * * * * * * 10-36 Name Factory Setting Setting No. Name Factory Setting N4-32 Speed estimator gain fluctuation frequency 1 5.0 o2-08 Cumulative operation time selection 0 N4-33 Speed estimator gain fluctuation frequency 2 20.0 o2-10 Fan operation time setting 0 N4-34 Speed estimator gain fluctuation rate 200.0 o2-12 Fault trace/fault history clear function 0 N5-01 Feed forward control selection 0*7 o2-14 Output power monitor clear selection 0 N5-02 Motor acceleration time N5-03 Feed forward proportional gain o1-01 0.178*6 o2-18*18 Capacitor maintenance setting 0 1.0 o3-01 Copy function selection 0 Monitor selection 6 o3-02 Read permitted selection 0 o1-02 Monitor selection after power up 1 T1-00 Motor 1/2 selection 1 o1-03 Frequency units of reference setting and monitor 0 T1-01 Autotuning mode selection o1-04 Setting unit for frequency constants related to V/f characteristics 0 T1-02 Motor output power 0.40*6 o1-05 LCD brightness adjustment 3 T1-03 Motor rated voltage 200.0*9 o2-01 LOCAL/REMOTE key enable/disable 1 T1-04 Motor rated current 1.90*6 o2-02 STOP key during control circuit terminal operation 1 T1-05 Motor base frequency 60.0 o2-03 User constant initial value 0 T1-06 Number of motor poles 4 o2-04 kVA selection 0*6 T1-07 Motor base speed 1750 o2-05 Frequency reference setting method selection 0 T1-08 PG pulses per revolution for teaching 600 o2-06 Operation selection when digital operator is disconnected 0 o2-07 Cumulative operation time setting 0 1. 2. 3. 4. T1-09*18 Motor no-load current 0*2 1.20*6 Not initialized. (Japanese standard specifications: A1-00 = 1, A1-02 = 2) When the control method is changed, the factory setting will change. The open-loop vector 1 factory settings are given. The factory setting is 1.0 when using flux vector control. The factory setting is 2.00 s when Inverter capacity is 55 kW min. The factory setting will change when the control method is changed. The open-loop vector 1 factory setting is given. 5. By setting E2-11 (Motor rated output) the appropriate value will be set. 6. The factory settings depend on the Inverter capacity. The values for a 200 V Class Inverter of 0.4 kW are given. 7. When the control method is changed, the factory settings will change. The flux vector factory settings are given. 8. This constant can be monitored or set only when F is set for C6-02. 9. These are values for a 200 V Class Inverter. Values for a 400 V Class Inverter are double. 10.E1-11 and E1-12 are disregarded when set to 0.0. 11.E1-13 is set to the same value as E1-05 by autotuning. 12.The same capacity as that of the Inverter will be set if the constants are initialized. 13.Applicable for G7-Series Inverters with software versions PRG: 1038 and later. Refer to MECHATROLINK COMMUNICATIONS INTERFACE CARD INSTRUCTIONS (TOBPC73060008) for details. 14.The factory settings in the parentheses are for 3-wire sequence. Setting User Constants * * * * * 15.If the setting is 0, the axis will accelerate to the specified speed for the specified acceleration time (C1-01 to C1-08). 16.Applicable for G7-Series Inverters with software versions PRG: 1038 and later. 17.Applicable for G7-Series Inverters with software versions RPG: 1034 or later. 18.Applicable for G7-Series Inverters with software versions PRG:1039 or later. 19.If a current exceeding 110% of the Inverter rated current flows through the unit, the carrier frequency will automatically decrease and electromagnetic noise will occur. 10 10-37 Index INDEX digital operator connection fault - - - - - - - - - - - - - - - - - - - - -7-9 digital output cards - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-162 drive mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-5, 3-7 dwell function - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-22 Symbols +/- speed - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6-82 Numerics 2-wire sequence - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6-10 3-wire sequence - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6-11 A AC reactor - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2-17 acceleration and deceleration times - - - - - - - - - - - - - - - - - -6-18 advanced programming mode - - - - - - - - - - - - - - - - - - 3-5, 3-10 ASIC internal RAM fault - - - - - - - - - - - - - - - - - - - - - - - -7-11 ASIC version fault - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-11 auto restart - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6-72 autotuning - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-9 autotuning mode - - - - - - - - - - - - - - - - - - - - - - - - - - 3-5, 3-14 B baseblock circuit error - - - - - - - - - - - - - - - - - - - - - - - - - -7-10 braking resistor - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2-21 braking resistor unit - - - - - - - - - - - - - - - - - - - - - - -2-21, 10-20 braking unit- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10-21 BUS Option Com Err - - - - - - - - - - - - - - - - - - - - - - -7-10, 7-18 C CALL Com Call - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-18 CE MEMOBUS Com Err - - - - - - - - - - - - - - - - - - - - - - - -7-18 CE Memobus Com Err - - - - - - - - - - - - - - - - - - - - - - - - - -7-10 CF out of control - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-8 circuit breaker - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2-16 common specifications - - - - - - - - - - - - - - - - - - - - - - - - - - 9-4 communications on standby - - - - - - - - - - - - - - - - - - - - - - -7-18 communications option board A/D converter error - - - - - - - - -7-11 communications option card DPRAM error - - - - - - - - - - - - -7-12 communications option card model code error - - - - - - - - - - - -7-11 communications option card self diagnostic error - - - - - - - - - -7-11 constant selection error - - - - - - - - - - - - - - - - - - - - - - - - - -7-20 constant setting error - - - - - - - - - - - - - - - - - - - - - - - - - - -7-21 constant setting range error - - - - - - - - - - - - - - - - - - - - - - -7-20 control circuit terminals - - - - - - - - - - - - - - - - - - - - - - - - -2-22 control fault - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-8 control method - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-8 control method selection error - - - - - - - - - - - - - - - - - - - - -7-20 control power fault - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-4 cooling fin overheating - - - - - - - - - - - - - - - - - - - - - - - - - - 7-4 CPF00 CPF - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-10 CPF01 CPF01 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-10 CPU internal A/D converter error - - - - - - - - - - - - - - - - - - -7-11 CPU-ASIC mutual diagnosis fault - - - - - - - - - - - - - - - - - - -7-11 crimp terminals - - - - - - - - - - - - - - - - - - - - - - 2-6, 2-22, 2-38 D daily inspection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-2 DC reactor - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2-17 detecting motor overspeed - - - - - - - - - - - - - - - - - - - - - - - 6-161 detecting motor torque - - - - - - - - - - - - - - - - - - - - - - - - - -6-53 detecting PG open circuit - - - - - - - - - - - - - - - - - - - - - - - 6-161 DEV Speed Deviation - - - - - - - - - - - - - - - - - - - - - - - - - -7-16 digital operator - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-2 digital operator communications error 1 - - - - - - - - - - - - - - - -7-10 digital operator communications error 2 - - - - - - - - - - - - - - - -7-10 Index-1 E EEPROM error - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-10 EEPROM write error - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-21 EF External Fault - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-15 EF0 Opt External Flt - - - - - - - - - - - - - - - - - - - - - - - 7-9, 7-17 emergency stop - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-17 enclosed wall-mounted type - - - - - - - - - - - - - - - - - - - - - - - -1-4 energy-saving - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-115 ERR EEPROM R/W Err - - - - - - - - - - - - - - - - - - - - - - - - - 7-21 excessive speed deviation - - - - - - - - - - - - - - - - - - - - 7-8, 7-16 external fault function - - - - - - - - - - - - - - - - - - - - - - - - - - 6-85 F FBL Feedback Loss - - - - - - - - - - - - - - - - - - - - - - - - 7-8, 7-17 FJOG - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-84 forward/reverse run commands input together - - - - - - - - - - - - 7-15 frequency reference - - - - - - - - - - - - - - - - - - - - - - - - 6-2, 6-28 fuse blown - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-3 G ground fault - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-2 ground fault interrupter - - - - - - - - - - - - - - - - - - - - - - - - - - 2-16 ground wiring - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-20 H high-slip braking OL - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-7 hunting-prevention function - - - - - - - - - - - - - - - - - - - - - - - 6-40 I incorrect inverter capacity setting - - - - - - - - - - - - - - - - - - - 7-20 inductive noise - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-19 inrush prevention circuit fault - - - - - - - - - - - - - - - - - - - - - - -7-4 installation site - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -1-9 installed braking resistor overheating - - - - - - - - - - - - - - - - - -7-5 internal braking transistor fault - - - - - - - - - - - - - - - - - - - - - -7-5 inverter input voltage - - - - - - - - - - - - - - - - - - - - - - - - - - 6-121 inverter overload - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-7 J jump frequency function - - - - - - - - - - - - - - - - - - - - - - - - - 6-31 L limiting motor rotation direction - - - - - - - - - - - - - - - - - - - - 6-62 loaded operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-16 M magnetic contactor - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-17 main circuit overvoltage - - - - - - - - - - - - - - - - - - - - - - - - - -7-3 main circuit undervoltage - - - - - - - - - - - - - - - - - - - - 7-3, 7-15 main circuit voltage fault - - - - - - - - - - - - - - - - - - - - - - - - -7-4 maintenance and inspection - - - - - - - - - - - - - - - - - - - - - - - -8-1 MEMOBUS communications - - - - - - - - - - - - - - - - - - - - - - 6-92 MEMOBUS communications error - - - - - - - - - - - - - -7-10, 7-18 modes - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -3-5 motor constants - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-117 motor overheating - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-16 motor overheating alarm - - - - - - - - - - - - - - - - - - - - - - - - - -7-5 motor overheating fault - - - - - - - - - - - - - - - - - - - - - - - - - -7-5 motor overload - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -7-6 motor protection operation time - - - - - - - - - - - - - - - - - - - - 6-59 mounting dimensions - - - - - - - - - - - - - - - - - - - - - - - - - - - -1-6 Index multi-function analog input - - - - - - - - - - - - - - - - - - - - - - 6-47 multi-function analog input selection error - - - - - - - - - - - - - 7-20 multi-function input selection error - - - - - - - - - - - - - - - - - - 7-20 multi-speed operation - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-5 N noise filter - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-17 no-load operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-16 number of gear teeth between PG and motor - - - - - - - - - - - -6-161 number of PG pulses - - - - - - - - - - - - - - - - - - - - - - - - - -6-160 O OH Heatsink Overtemp - - - - - - - - - - - - - - - - - - - - - - - - - 7-15 OH2 Over Heat 2 - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-15 OH3 Motor Overheat 1 - - - - - - - - - - - - - - - - - - - - - - - - - 7-16 OL3 Overtorque Det 1 - - - - - - - - - - - - - - - - - - - - - - - - - 7-16 OL4 Overtorque Det 2 - - - - - - - - - - - - - - - - - - - - - - - - - 7-16 OPE01 kVA Selection- - - - - - - - - - - - - - - - - - - - - - - - - - 7-20 OPE011 Carr Freq/On-Delay - - - - - - - - - - - - - - - - - - - - - 7-21 OPE02 Limit - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-20 OPE03 Terminal - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-20 OPE05 Sequence Select - - - - - - - - - - - - - - - - - - - - - - - - 7-20 OPE06 PG Opt Missing - - - - - - - - - - - - - - - - - - - - - - - - 7-20 OPE07 Analog Selection - - - - - - - - - - - - - - - - - - - - - - - - 7-20 OPE08 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-20 OPE09 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-20 OPE10 V/f Ptrn Setting - - - - - - - - - - - - - - - - - - - - - - - - - 7-20 open chassis type - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-4 open-loop vector control - - - - - - - - - - - - - - - - - - - - - - - - - 4-9 operation errors - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-20 OPR Oper Disconnect - - - - - - - - - - - - - - - - - - - - - - - - - - 7-9 option card communications error - - - - - - - - - - - - - - - - - - 7-18 option card connection error - - - - - - - - - - - - - - - - - - - - - - 7-11 option card selection error - - - - - - - - - - - - - - - - - - - - - - - 7-20 option communications error - - - - - - - - - - - - - - - - - - - - - 7-10 OS Overspeed Det - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-16 output open-phase - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-4 OV DC Bus Overvolt - - - - - - - - - - - - - - - - - - - - - - - - - - 7-15 overcurrent - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-2 overspeed - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-8, 7-16 overtorque 2 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-16 overtorque detected 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-7 overtorque detected 2 - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-7 P password - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-17, 6-156 periodic inspection - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-2 periodic maintenance of parts - - - - - - - - - - - - - - - - - - - - - - 8-3 PG (encoder) pulses - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-39 PG disconnection - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-16 PG disconnection detected - - - - - - - - - - - - - - - - - - - - - - - - 7-8 PG pulse monitor output dividing ratio - - - - - - - - - - - - - - -6-161 PG rotation direction - - - - - - - - - - - - - - - - - - - - - - - - - -6-160 PG speed control card - - - - - - - - - - - - - - - - - - - - - - - - - -6-160 PG speed control cards - - - - - - - - - - - - - - - - - - - - - - - - - 2-31 PGO PG Open - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-16 PID control - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6-106 PID control selection error - - - - - - - - - - - - - - - - - - - - - - - 7-20 PID feedback reference lost - - - - - - - - - - - - - - - - - - - 7-8, 7-17 power ON - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-3 rated current - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-58 RJOG - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-84 run command - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-10 S S-curve characteristics - - - - - - - - - - - - - - - - - - - - - - - - - 6-21 setting speed limit bias - - - - - - - - - - - - - - - - - - - - - - - - -6-132 slip compensation function - - - - - - - - - - - - - - - - - - - - - - - 6-36 speed control with PG - - - - - - - - - - - - - - - - - - - - - - - - -6-158 stabilizing speed - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-41 stall prevention function - - - - - - - - - - - - - - - - 6-23, 6-25, 6-50 standard connection diagrams - - - - - - - - - - - - - - - - - - - - - 2-15 standard inverter specifications - - - - - - - - - - - - - - - - - - - - - 9-2 stopping methods - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-12 straight solderless terminals - - - - - - - - - - - - - - - - - - 2-23, 2-38 surge absorber - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-17 switching motors when the power supply is ON - - - - - - - - - -6-149 T terminal block - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-5 thermal overload relay - - - - - - - - - - - - - - - - - - - - - - - - - 2-19 tightening torque - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-38 timer function - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -6-105 torque compensation - - - - - - - - - - - - - - - - - - - - - - - - - - 6-38 torque limit function - - - - - - - - - - - - - - - - - - - - - - - - - - 6-46 trial operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1 troubleshooting- - - - - - - - - - - - - - - - - - - - - - - - - - - 7-1, 7-25 U UL3 Undertorq Det 1 - - - - - - - - - - - - - - - - - - - - - - - - - - 7-16 UL4 Undertorq Det 2 - - - - - - - - - - - - - - - - - - - - - - - - - - 7-16 undertorque 1 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-16 undertorque 2 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-16 undertorque detected 1 - - - - - - - - - - - - - - - - - - - - - - - - - - 7-8 undertorque detected 2 - - - - - - - - - - - - - - - - - - - - - - - - - - 7-8 user constant access levels - - - - - - - - - - - - - - - - - - - - - - - 4-17 UV DC Bus Undervolt - - - - - - - - - - - - - - - - - - - - - - - - - 7-15 V V/f control - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-8 V/f control with PG - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-8 V/f pattern - - - - - - - - - - - - - - - - - - - - - - - - - - -6-120, 6-122 verify mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-5, 3-13 VS operator - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -10-24 W watchdog timer fault - - - - - - - - - - - - - - - - - - - - - - - - - - 7-11 wire size - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-22 wiring - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-1 Q quick programming mode - - - - - - - - - - - - - - - - - - - - - 3-5, 3-8 R radio interference - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-20 Index-2 Revision History The revision dates and numbers of the revised manuals are given on the bottom of the back cover. MANUAL NO.ޓTOE-S616-60.1B Published in Japan March 200301-05 1 Revision number Date of Date of original publication publication Date of Publication Rev. No. − − First edition March 2003 1 − Addition: Constants for the Inverters with software version PRG:102, description of replacing cooling fan and circulation fan, etc. April 2003 2 Back cover Revision: Address July 2003 3 Chapter 4 Revision: Stationary Autotuning (T1-01=1) Addition: Precautions After Using Rotational and Stationary Autotuning January 2004 4 Chapter 2 Addition: Note 12 to connection diagram. Note after main circuit configuration diagrams for C1MR-G7A2030 to 2110. Explanation of I/O circuit configuration diagram for PG-B2. Chapter 5 Addition: Values for 400 V Class Inverters of 300 kW under Factory Settings that Change with the Inverter Capacity. Note 5 for carrier frequency C6-03 to C6-05. Chapter 6 Revision: Multi-function contact input terminals S7, S8 for multi-step operation to S9, S7. Addition: Output Terminal Function Explanation of restrictions on maximum output frequency depending on carrier frequency under Reducing Noise and Leakage Current. Using Inverters for Elevating Machines Chapter 7 Revision: Main circuit capacitor neutral point potential error causes and corrective action under Fault Detection. Addition: Operator errors in table under Fault Detection. Reset during Run Command input error under Alarm Detection. Chapter 9 Revision: Input noise filter model numbers under Specifications of Options and Peripheral Devices. Addition: Notes 4 and 5 under Common Specifications. Chapter 10 Revision: Precautions for Open-loop Vector 2 Control. Addition: Applications with Repetitive Loads Preface Addition: Warranty Information May 2001 September 2004 5 Section Revised Content Chapter 1 Addition: Removing and Attaching the Protection Cover Chapter 2 Revision: Inverter main circuit configuration diagrams for models CIMR-F7A2037 to 2110 and CIMR-F7A4075 to 4300 Addition: LONWORKS Communications Boards SI-J and SI-W1 in Table 2.14 Option Board Specifications Chapter 4 Addition: Setting 3 for Constant T1-01 Chapter 5 Chapter 5 Addition: Constant N1-03 Chapter 6 Chapter 10 January 2005 September 2005 6 7 Chapter 6 Deletion: Speed Limit Bias Setting under Torque Control Chapter 7 Addition: PG Direction and PG Open in Table 7.4 Errors During Autotuning Chapter 8 Addition: Procedure for Adjusting Constants after Replacement of Control Board Chapter 9 Addition: LONWORKS Communications Boards SI-J and SI-W1 in Table 9.5 Option Boards Chapter 3 Addition: y DATA/ENTER Key is invalid when UV is detected. y Table 3.2 Relation of Inverter to RUN and STOP Indicators Chapter 7 Revision: Note about GF in Table 7.1 Fault Displays and Processing. Addition: Note about OC and GF in the Meaning column in Table 7.1 Fault Displays and Processing. Back cover Revision: Address Date of Publication June 2006 Rev. No. 8 Section Revised Content Preface Addition: Safety Precautions • Setting User Constants Stationary autotuning precautions • Trial Operation Inverter settings precautions • Maintenance and Inspection Precaution about using an Inverter with an elevator Precaution about times when a holding brake is necessary Chapter 1 Revision: Fig1.9 Removing the Terminal Cover (Model CIMR-G7A23P7 Shown Above) Chapter 2 Addition: • Note in Table 2.4 Main Circuit Terminal Functions • IMPORTANT 12, 13, and 14 in Connection Diagram • IMPORTANT in Standard Connection Diagrams • Table 2.14 Option Board Specifications MECHATROLINK Communication Board • Fig 2.22 Cutting the Front Cover Revision: • IMPORTANT 2 in Connection Diagram • Factory setting for multi-function photo-coupler output 4 frequency detection 2 → minor fault • Table 2.2 400 V Class Wire Sizes Following recommended wire sizes:G7A4185, G7A4220, G7A4300 • Description of installing a ground fault interrupter in Wiring the Main Circuits • Fig 2.24 Wiring an Open-collector Input Chapter 4 Addition: • Precautions for precision settings • Description of stationary autotuning 2 Revision: • Fig 4.1 Trial Operation Flowchart • Fig 4.3 Settings According to the Control Method • Checking Operating Status under Loaded Operation Chapter 5 Addition: • Following constants b3-17, b3-18, b3-19, F6-08, F6-09, H5-10, L8-32, L8-39, L8-41, U1-61, U1-63, U1-83, U1-84, U2-21, U2-22, o2-18, T1-09 • 2 setting of b1-08 • 4 setting of T1-01 • Note in the table of L2 constants • Note *2 in the table of U2 constants • 2F, 36, and 3D settings of multi-function output terminal • Note *5 about C4-02 in the table in Factory Settings that Change with the Control Method (A1-02) • L8-39 in the table in Factory Settings that Change with the Inverter Capacity (o2-04) Revision: • Note *2 about E2-01 • Note *3 about E2-03 and E4-03 • Note *8 about T1-09 Chapter 6 Addition: • Inputting Master Speed Frequency Reference Only (Current Input) in Frequency Reference • Following items in Continuing Operation • IMPORTANT in Speed Search • Additional description of master speed analog input in Continuing Operation at Constant Speed When Frequency Reference Is Lost • Varispeed F7 Function Block • Frequency Detection 5 in Using Frequency Detection • Setting the V/f Pattern Description about the changes in the OV and BTR levels that depend on the input voltage in Setting the V/f Pattern. • Torque Control Description of setting speed limit bias • Comparing Inverter Constants and Digital Operator Constant Set Values (VERIFY) under Digital Operator Functions Description of error display CPE • Using Inverters for Elevating Machines • Description about frequency detection 5, which is an Inverter output signal to engage a holding brake • IMPORTANT about precautions on trial operation • IMPORTANT in Brake ON/OFF Sequence • Current Alarm Function • Peak Hold Current Monitoring Function • Maintenance Timer Display Function Date of Publication June 2006 Rev. No. 8 Section Revised Content Chapter 6 Revision: • Restarting Operation After Transient Fault (Auto Restart Function) under Continuing Operation • Description of OH1 detection of Inverter’s cooling fan fault • Fig 6.50 Baseblock Commands • Fig 6.64 PID Control Block • Torque Control under Individual Operation Example Diagrams of winding and rewinding operation during torque control • Application precautions in Copying Constants • Using Inverters for Elevating Machines • Fig 6.85 Brake ON/OFF Sequence Circuit Configuration • Description in Confirming Startup Current and Reducing Carrier Frequency Chapter 7 Addition: • Fault Detections Descriptions of FAN, SER, and E5 • Alarm Detections Descriptions of FAN, E5, AEr, CyC, BB, HCA, LT-F, and LT-C • Table 7.2 Causes and Corrective Actions for When the Digital Operator Goes Dark • Note in Table 7.3 Operation Error Displays and Incorrect Settings • Adjusted Silp Value in Table 7.5 Errors During Autotuning • CPE in Table 7.6 Errors during Copy Function • Following descriptions in Troubleshooting • The Inverter does not operate • Acoustic Noise from the Motor Changes Revision: • Probable causes and corrective actions for the OC, GF, PUF, OV, UV1, UV2, UV3, OH (OH1), OL1, OL2, PGO, DEV, CPF03 to CPF05 and CPF23 faults and OH, FBL, PGO, and DEV alarms Deletion: • Alarm Detections Descriptions of E-15 Chapter 8 Addition: • Descriptions in Periodic Maintenance of Parts • Description of how to attach the fan cover for 200 V Class Inverters of 22 kW, 45 kW, 55 kW, 400 V Class Inverters of 18.5 kW to 75 kW • Description of how to replace the cooing fan and circulation fan for 400 V Class Inverters of 185 kW, 220 kW, and 300 kW Revision: Procedure for Adjusting Constants after Replacement of Control Board Chapter 9 Addition: • Rated input current in Table 9.1 200 V Class Inverters and Table 9.2 400 V Class Inverters • Notes *7 and *8 in Table 9.3 Common Specifications • MECHATROLINK Communications Interface Board SI-T in Table 9.5 Option Boards Chapter 10 Addition: • Conformance to UL standard • Conformance to CE markings • Note *4 in Fig 10.9 November 2007 9 Back cover Revision: Address March 2008 10 Back cover Revision: Address 11 Back cover Revision: Address June 2008 Varispeed G7 INSTRUCTION MANUAL IRUMA BUSINESS CENTER (SOLUTION CENTER) 480, Kamifujisawa, Iruma, Saitama 358-8555, Japan Phone 81-4-2962-5696 Fax 81-4-2962-6138 YASKAWA ELECTRIC AMERICA, INC. 2121 Norman Drive South, Waukegan, IL 60085, U.S.A. Phone 1-847-887-7000 Fax 1-847-887-7370 YASKAWA ELETRICO DO BRASIL LTDA. Avenida Fagundes Filho, 620 Sao Paulo-SP CEP 04304-000, Brazil Phone 55-11-3585-1100 Fax 55-11-5581-8795 YASKAWA ELECTRIC EUROPE GmbH Hauptstraβe 185, 65760 Eschborn, Germany Phone 49-6196-569-300 Fax 49-6196-569-398 YASKAWA ELECTRIC UK LTD. 1 Hunt Hill Orchardton Woods Cumbernauld, G68 9LF, United Kingdom Phone 44-1236-735000 Fax 44-1236-458182 YASKAWA ELECTRIC KOREA CORPORATION 7F, Doore Bldg. 24, Yeoido-dong, Youngdungpo-Ku, Seoul 150-877, Korea Phone 82-2-784-7844 Fax 82-2-784-8495 YASKAWA ELECTRIC (SINGAPORE) PTE. LTD. 151 Lorong Chuan, #04-01, New Tech Park 556741, Singapore Phone 65-6282-3003 Fax 65-6289-3003 YASKAWA ELECTRIC (SHANGHAI) CO., LTD. No.18 Xizang Zhong Road. Room 1702-1707, Harbour Ring Plaza Shanghai 200001, China Phone 86-21-5385-2200 Fax 86-21-5385-3299 YASKAWA ELECTRIC (SHANGHAI) CO., LTD. BEIJING OFFICE Room 1011A, Tower W3 Oriental Plaza, No.1 East Chang An Ave., Dong Cheng District, Beijing 100738, China Phone 86-10-8518-4086 Fax 86-10-8518-4082 YASKAWA ELECTRIC TAIWAN CORPORATION 9F, 16, Nanking E. Rd., Sec. 3, Taipei, Taiwan Phone 886-2-2502-5003 Fax 886-2-2505-1280 YASKAWA ELECTRIC CORPORATION YASKAWA In the event that the end user of this product is to be the military and said product is to be employed in any weapons systems or the manufacture thereof, the export will fall under the relevant regulations as stipulated in the Foreign Exchange and Foreign Trade Regulations. Therefore, be sure to follow all procedures and submit all relevant documentation according to any and all rules, regulations and laws that may apply. Specifications are subject to change without notice for ongoing product modifications and improvements. © 2001-2008 YASKAWA ELECTRIC CORPORATION. All rights reserved. MANUAL NO. TOE-S616-60.1E Published in Japan June 2008 01-5 11 -0 08-5-10 ">
/
다운로드
친절한 알림입니다. 여기에서 문서를 볼 수 있습니다. 그러나 가장 중요한 것은 AI가 이미 읽었다는 것입니다. 복잡한 내용을 간단하게 설명하고, 모든 언어로 질문에 답변하고, 가장 길거나 복잡한 문서도 빠르게 탐색할 수 있도록 도와줍니다.
공개 링크 업데이트됨
문서 공개 링크
광고
